Automated Certificate Management Environment B. Sipos
Internet-Draft RKF Engineering
Intended status: Experimental 14 November 2021
Expires: 18 May 2022
Automated Certificate Management Environment (ACME) Delay-Tolerant
Networking (DTN) Node ID Validation Extension
draft-ietf-acme-dtnnodeid-07
Abstract
This document specifies an extension to the Automated Certificate
Management Environment (ACME) protocol which allows an ACME server to
validate the Delay-Tolerant Networking (DTN) Node ID for an ACME
client. The DTN Node ID is encoded as a certificate Subject
Alternative Name (SAN) of type otherName with a name form of
BundleEID and as an ACME Identifier type "bundleEID".
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 18 May 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
Sipos Expires 18 May 2022 [Page 1]
Internet-Draft ACME DTN Node ID November 2021
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Simplified BSD License text
as described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2. Authorization Strategy . . . . . . . . . . . . . . . . . 5
1.3. Use of CDDL . . . . . . . . . . . . . . . . . . . . . . . 6
1.4. Terminology . . . . . . . . . . . . . . . . . . . . . . . 7
2. Bundle Endpoint ID ACME Identifier . . . . . . . . . . . . . 7
3. DTN Node ID Validation . . . . . . . . . . . . . . . . . . . 8
3.1. DTN Node ID Challenge Request Object . . . . . . . . . . 11
3.2. DTN Node ID Challenge Response Object . . . . . . . . . . 12
3.3. ACME Node ID Validation Challenge Bundles . . . . . . . . 13
3.3.1. Challenge Bundle Checks . . . . . . . . . . . . . . . 14
3.4. ACME Node ID Validation Response Bundles . . . . . . . . 14
3.4.1. Response Bundle Checks . . . . . . . . . . . . . . . 16
3.5. Multi-Perspective Validation . . . . . . . . . . . . . . 16
4. Bundle Integrity Gateway . . . . . . . . . . . . . . . . . . 17
5. Certificate Request Profile . . . . . . . . . . . . . . . . . 17
5.1. Multiple Identity Claims . . . . . . . . . . . . . . . . 18
5.2. Generating Encryption-only or Signing-only Bundle Security
Certificates . . . . . . . . . . . . . . . . . . . . . . 18
6. Implementation Status . . . . . . . . . . . . . . . . . . . . 18
7. Security Considerations . . . . . . . . . . . . . . . . . . . 19
7.1. Threat: Passive Leak of Validation Data . . . . . . . . . 19
7.2. Threat: BP Node Impersonation . . . . . . . . . . . . . . 20
7.3. Threat: Bundle Replay . . . . . . . . . . . . . . . . . . 20
7.4. Threat: Denial of Service . . . . . . . . . . . . . . . . 20
7.5. Inherited Security Considerations . . . . . . . . . . . . 21
7.6. Out-of-Scope BP Agent Communication . . . . . . . . . . . 21
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22
8.1. ACME Identifier Types . . . . . . . . . . . . . . . . . . 22
8.2. ACME Validation Methods . . . . . . . . . . . . . . . . . 22
8.3. Bundle Administrative Record Types . . . . . . . . . . . 22
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 23
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.1. Normative References . . . . . . . . . . . . . . . . . . 23
10.2. Informative References . . . . . . . . . . . . . . . . . 25
Appendix A. Administrative Record Types CDDL . . . . . . . . . . 27
Appendix B. Example Authorization . . . . . . . . . . . . . . . 27
Sipos Expires 18 May 2022 [Page 2]
Internet-Draft ACME DTN Node ID November 2021
B.1. Challenge Bundle . . . . . . . . . . . . . . . . . . . . 27
B.2. Response Bundle . . . . . . . . . . . . . . . . . . . . . 28
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 29
1. Introduction
Although the original purpose of the Automatic Certificate Management
Environment (ACME) [RFC8555] was to allow Public Key Infrastructure
Using X.509 (PKIX) certificate authorities to validate network domain
names of clients, the same mechanism can be used to validate any of
the subject claims supported by the PKIX profile [RFC5280].
In the case of this specification, the claim being validated is a
Subject Alternative Name (SAN) of type otherName with a name form of
BundleEID, which used to represent an Endpoint ID (EID) for a Delay-
Tolerant Networking (DTN) bundle. Currently the URI schemes "dtn"
and "ipn" as defined in [I-D.ietf-dtn-bpbis] are valid for an
Endpoint ID. A DTN Node ID is an Endpoint ID with scheme-specific
restrictions to identify it as such; currently the "dtn" scheme uses
an empty demux part and the "ipn" scheme uses service number zero.
Because the BundleEID claim is new to ACME, a new ACME Identifier
type "bundleEID" is needed to manage this claim within ACME
messaging. A "bundleEID" claim can be part of a pre-authorization or
as one of the authorizations of an order containing any number of
claims.
Once an ACME server validates a Node ID, either as a pre-
authorization of the "bundleEID" or as one of the authorizations of
an order containing a "bundleEID", the client can finalize the order
using an associated certificate signing request (CSR). Because a
single order can contain multiple identifiers of multiple types,
there can be operational issues for a client attempting to, and
possibly failing to, validate those multiple identifiers as described
in Section 5.1. Once a certificate is issued for a Node ID, how the
ACME client configures the Bundle Protocol (BP) agent with the new
certificate is an implementation matter.
The scope and behavior of this validation mechanism is similar to
that of secured email validation of [RFC8823].
1.1. Scope
This document describes the ACME messages, BPv7 payloads, and BPSec
requirements needed to validate Node ID ownership. This document
does not address:
Sipos Expires 18 May 2022 [Page 3]
Internet-Draft ACME DTN Node ID November 2021
* Mechanisms for communication between ACME client or ACME server
and their associated BP agent(s). This document only describes
exchanges between ACME client--server pairs and between their BP
agents.
* Specific BP extension blocks or BPSec security contexts necessary
to fulfill the security requirements of this protocol. The exact
security context needed, and their parameters, are network-
specific.
* Policies or mechanisms for defining or configuring bundle
integrity gateways, or trusting integrity gateways on an
individual entity or across a network.
* Mechanisms for locating or identifying other bundle entities
(peers) within a network or across an internet. The mapping of
Node ID to potential convergence layer (CL) protocol and network
address is left to implementation and configuration of the BP
Agent and its various potential routing strategies.
* Logic for routing bundles along a path toward a bundle's endpoint.
This protocol is involved only in creating bundles at a source and
handling them at a destination.
* Logic for performing rate control and congestion control of bundle
transfers. The ACME server is responsible for rate control of
validation requests.
* Policies or mechanisms for provisioning, deploying, or accessing
certificates and private keys; deploying or accessing certificate
revocation lists (CRLs); or configuring security parameters on an
individual entity or across a network.
* Policies or mechanisms for an ACME server to handle mixed-use
certificate requests. This specification is focused only on
single-use DTN-specific PKIX profiles.
Sipos Expires 18 May 2022 [Page 4]
Internet-Draft ACME DTN Node ID November 2021
1.2. Authorization Strategy
The basic unit of data exchange in a DTN is a Bundle
[I-D.ietf-dtn-bpbis], which consists of a data payload with
accompanying metadata. An Endpoint ID is used as the destination of
a Bundle and can indicate both a unicast or a multicast destination.
A Node ID is used to identify the source of a Bundle and is used for
routing through intermediate nodes, including the final node(s) used
to deliver a Bundle to its destination endpoint. A Node ID can also
be used as an endpoint for administrative bundles. More detailed
descriptions of the rationale and capabilities of these networks can
be found in "Delay-Tolerant Network Architecture" [RFC4838].
When an ACME client requests a pre-authorization or an order with a
"bundleEID" identifier type having a value consistent with a Node ID
(see Section 4.2.5 of [I-D.ietf-dtn-bpbis]), the ACME server offers a
"dtn-nodeid-01" challenge type to validate that Node ID. If the ACME
client attempts the authorization challenge to validate a Node ID,
the ACME server sends an ACME Node ID Validation Challenge Bundle
with a destination of the Node ID being validated. The BP agent on
that node receives the Challenge Bundle, generates an ACME key
authorization digest, and sends an ACME Node ID Validation Response
Bundle in reply. An Integrity Gateway on the client side of the DTN
can be used to attest to the source of the Response Bundle. Finally,
the ACME server receives the Response Bundle and checks that the
digest was generated for the associated ACME challenge and from the
client account key associated with the original request. This
workflow is shown in the diagram of Figure 1 and defined in
Section 3.
Sipos Expires 18 May 2022 [Page 5]
Internet-Draft ACME DTN Node ID November 2021
+------------+ +------------+
| ACME |<===== HTTPS exchanges =====>| ACME |
| Client | | Server |
+------------+ +------------+
| | ^
(1) Enable or (6) disable (2) Send | |
validation from server Challenge | |(5) Indicate
| Non-DTN | | Response
~~~~~~~~~~~|~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|~~~|~~~~~~~~~~~~
V DTN V |
++------------++ ++------------++
|| Admin Elem.|| || Admin Elem.||-+
|+------------+| (3) Challenge |+------------+| |
| Client's |<------------- Bundle -----| Server's | |
| BP Agent | | BP Agent | |
+--------------+ +--------------+ |
| +----^---------+
| +-------------+ |
| | Integrity | (4) Response |
+---->| Gateway |------ Bundle --------+
+-------------+
Figure 1: The relationships and flows between Node ID Validation
entities
Because the DTN Node ID is used both for routing bundles between BP
agents and for multiplexing administrative services within a BP
agent, there is no possibility to separate the ACME validation of a
Node ID from normal bundle handling for that same Node ID. This
leaves administrative record types as a way to leave the Node ID
unchanged while disambiguating from other service data bundles.
There is nothing in this protocol which requires network-topological
co-location of either the ACME client or ACME server with their
associated BP agent. While ACME requires a low-enough latency
network to perform HTTPS exchanges between ACME client and server,
the client's BP agent (the one being validated) could be on the far
side of a long-delay or multi-hop DTN network. The means by which
the ACME client or server communicates with its associated BP agent
is an implementation matter.
1.3. Use of CDDL
This document defines CBOR structure using the Concise Data
Definition Language (CDDL) of [RFC8610]. The entire CDDL structure
can be extracted from the XML version of this document using the
XPath expression:
Sipos Expires 18 May 2022 [Page 6]
Internet-Draft ACME DTN Node ID November 2021
'//sourcecode[@type="cddl"]'
The following initial fragment defines the top-level symbols of this
document's CDDL, which includes the example CBOR content.
start = acme-record / bundle / tstr
1.4. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
In this document, several terms are shortened for the sake of
terseness. These terms are:
Challenge Request: This is a shortened form of the full "DTN Node ID
Challenge Request Object". It is a JSON object created by the
ACME server for challenge type "dtn-nodeid-01".
Challenge Response: This is a shortened form of the full "DTN Node
ID Challenge Response Object". It is a JSON object created by the
ACME client to authorize a challenge type "dtn-nodeid-01".
Challenge Bundle: This is a shortened form of the full "ACME Node ID
Validation Challenge Bundle". It is a Bundle created by the BP
agent managed by the ACME server to challenge a Node ID claim.
Response Bundle: This is a shortened form of the full "ACME Node ID
Validation Response Bundle". It is a Bundle created by the BP
agent managed by the ACME client to validate a Node ID claim.
2. Bundle Endpoint ID ACME Identifier
This specification is the first to make use of an Bundle Endpoint ID
to identify a claim for a certificate request in ACME. In this
document, the only purpose for which an Bundle Endpoint ID ACME
identifier is validated is as a DTN Node ID (see Section 3), but
other specifications can define challenge types for other Endpoint ID
uses.
Identifiers of type "bundleEID" in certificate requests MUST appear
in an extensionRequest attribute [RFC2985] containing a
subjectAltName extension of type otherName with a name form of
BundleEID, identified by id-on-bundleEID of [IANA-SMI], consistent
with the requirements of Section 4.4.2.1 of [I-D.ietf-dtn-tcpclv4].
Sipos Expires 18 May 2022 [Page 7]
Internet-Draft ACME DTN Node ID November 2021
Because the BundleEID is encoded as an IA5String it SHALL be treated
as being in the percent-encoded form of Section 2.1 of [RFC3986].
Any "bundleEID" identifier which fails to properly percent-decode
SHALL be rejected with an ACME error type of "malformed".
The ACME server SHALL decode and normalize (based on scheme-specific
syntax) all received identifiers of type "bundleEID". Any
"bundleEID" identifier request which uses a scheme not handled by the
ACME server or for which the EID does not match the scheme-specific
syntax SHALL be rejected with an ACME error type of
"rejectedIdentifier".
When an ACME server needs to request proof that a client controls a
BundleEID, it SHALL create an authorization with the identifier type
"bundleEID". The ACME server SHALL NOT attempt to dereference the
EID value on its own. It is the responsibility of a validation
method to ensure the EID ownership via scheme-specific means
authorized by the ACME client.
An identifier for the Node ID of "dtn://example/" would be formatted
as:
{
"type": "bundleEID",
"value": "dtn://example/"
}
3. DTN Node ID Validation
The DTN Node ID validation method proves control over a Node ID by
requiring the ACME client to configure a BP agent to respond to
specific Challenge Bundles sent from the ACME server. The ACME
server validates control of the Node ID by verifying that received
Response Bundles correspond with the BP Node and client account key
being validated.
Similar to the ACME use case for validating email address ownership
[RFC8823], this challenge splits the token into several parts, each
being transported by a different channel, and the Key Authorization
result requires combining all parts of the token. The token parts
are:
token-chal: This token is unique to, and identifies, each ACME
authorization. It is contained in the Challenge Object of
Section 3.1 as well as the Challenge Bundle of Section 3.3 and
Response Bundle of Section 3.4. Each authorization can consist of
multiple Challenge Bundles (e.g. taking different routes), but
they all share the same token-chal value. This ensures that the
Sipos Expires 18 May 2022 [Page 8]
Internet-Draft ACME DTN Node ID November 2021
Key Authorization is bound to the specific ACME challenge (and
parent ACME authorization) and also allows the ACME client's BP
agent to filter-in only valid Challenge Bundles. This token is
also accessible to DTN on-path eavesdroppers.
token-bundle: This token is unique to each Challenge Bundle sent by
the ACME server. It is contained in the Challenge Bundle of
Section 3.3 and Response Bundle of Section 3.4. This ensures that
the Key Authorization is bound to the ability to receive the
Challenge Bundle and not just have access to the ACME Challenge
Object. This token is also accessible to DTN on-path
eavesdroppers.
For each ACME server, the pair of token-chal and token-bundle values
is the unique correlator between Challenge and Response bundles.
Because multiple Challenge Bundles can be sent to validate the same
Node ID, the token-bundle in the response is needed to correlate with
the expected Key Authorization digest.
The DTN Node ID Challenge SHALL only be allowed for an EID usable as
a DTN Node ID, which [I-D.ietf-dtn-bpbis]. When an ACME server
supports Node ID validation, the ACME server SHALL define a challenge
object in accordance with Section 3.1. Once this challenge object is
defined, the ACME client may begin the validation.
To initiate a Node ID validation, the ACME client performs the
following steps:
1. The ACME client POSTs a newOrder or newAuthz request including
the identifier of type "bundleEID" for the desired Node ID. From
either of these entry points an authorization for the "bundleEID"
type is indicated by the ACME server. See Section 7.4 of
[RFC8555] for more details.
2. The ACME client obtains the challenge source Node ID and token-
chal from the challenge object in accordance with Section 3.1.
3. The ACME client indicates to the administrative element of its BP
agent the source Node ID and challenge token-chal which is
authorized for use and the associated client account key
thumbprint. The ACME client SHALL wait, if necessary, until the
agent is configured before proceeding to the next step.
4. The ACME client POSTs a challenge response to the challenge URL
on the ACME server accordance with Section 7.5.1 of [RFC8555].
The payload object is constructed in accordance with Section 3.2.
Sipos Expires 18 May 2022 [Page 9]
Internet-Draft ACME DTN Node ID November 2021
5. The administrative element waits for a Challenge Bundle to be
received with the authorized ACME parameters, including its
token-bundle payload, in accordance with Section 3.3.
6. The administrative element concatenates token-bundle with token-
chal (each as base64url-encoded text strings) and computes the
Key Authorization in accordance with Section 8.1 of [RFC8555]
using the full token and client account key thumbprint.
7. The administrative element computes the SHA-256 digest of the Key
Authorization result and generates a Response Bundle to send back
to the ACME server in accordance with Section 3.4.
8. The ACME client waits for the authorization to be finalized on
the ACME server in accordance with Section 7.5.1 of [RFC8555].
9. Once the challenge is completed (successfully or not), the ACME
client indicates to the BP agent that the validation source and
token-chal is no longer usable. If the authorization fails, the
ACME client MAY retry the challenge from Step 3.
The ACME server verifies the client's control over a Node ID by
performing the following steps:
1. The ACME server receives a newOrder or newAuthz request including
the identifier of type "bundleEID", where the URI value is a Node
ID.
2. The ACME server generates an authorization for the Node ID with
challenge type "dtn-nodeid-01" in accordance with Section 3.1.
3. The ACME server receives a POST to the challenge URL indicated
from the authorization object. The payload is handled in
accordance with Section 3.2.
4. The ACME server sends, via the administrative element of its BP
agent, one or more Challenge Bundles in accordance with
Section 3.3. Each challenge bundle SHALL contain a distinct
token-bundle to be able to correlate with a response bundle.
Computing an expected Key Authorization digest is not necessary
until a response is received.
5. The ACME server waits for Response Bundle(s) for a limited
interval of time (based on the challenge response object of
Section 3.2). Responses are encoded in accordance with
Section 3.4.
Sipos Expires 18 May 2022 [Page 10]
Internet-Draft ACME DTN Node ID November 2021
6. Once received and decoded, the ACME server checks the contents of
each Response Bundle in accordance with Section 3.4.1. After all
Challenge Bundles have either been responded to or timed-out, the
ACME server policy (see Section 3.5) determines whether the
validation is successful. If validation is not successful, a
client may retry the challenge which starts in Step 3.
When responding to a Challenge Bundle, a BP agent SHALL send a single
Response Bundle in accordance with Section 3.4. A BP agent SHALL
respond to ACME challenges only within the interval of time, only for
the Node ID, and only for the token-chal indicated by the ACME
client. A BP agent SHALL respond to multiple Challenge Bundles with
the same ACME parameters but different bundle identities (source Node
ID and timestamp); these correspond with the ACME server validating
via multiple routing paths.
3.1. DTN Node ID Challenge Request Object
The DTN Node ID Challenge request object is defined by the ACME
server when it supports validating Node IDs.
The DTN Node ID Challenge request object has the following content:
type (required, string): The string "dtn-nodeid-01".
source (required, array of string): An unordered list of possible
source Node ID of bundles originating at the BP agent(s) of the
ACME server. See Section 3.5 for a discussion of multi-
perspective validation using multiple sources. The array SHALL be
non-empty. The array MAY contain Node IDs which are not actually
used as a challenge bundle source.
token-chal (required, string): A random value that uniquely
identifies the challenge. This value MUST have at least 128 bits
of entropy. It MUST NOT contain any characters outside the
base64url alphabet as described in Section 5 of [RFC4648].
Trailing '=' padding characters MUST be stripped. See [RFC4086]
for additional information on randomness requirements.
{
"type": "dtn-nodeid-01",
"url": "https://example.com/acme/chall/prV_B7yEyA4",
"source": ["dtn://acme-server/"],
"token-chal": "tPUZNY4ONIk6LxErRFEjVw"
}
Sipos Expires 18 May 2022 [Page 11]
Internet-Draft ACME DTN Node ID November 2021
The token-chal value included in this object is fixed for the entire
challenge, and may correspond with multiple separate token-bundle
values when multiple Challenge Bundles are sent for a single
validation.
3.2. DTN Node ID Challenge Response Object
The DTN Node ID Challenge response object is defined by the ACME
client when it authorizes validation of a Node ID. Because a DTN has
the potential for significantly longer delays than a non-DTN network,
the ACME client is able to inform the ACME server if a particular
validation round-trip is expected to take longer than normal network
delays (on the order of seconds).
The DTN Node ID Challenge response object has the following content:
rtt (optional, number): An expected round-trip time (RTT), in
seconds, between sending a Challenge Bundle and receiving a
Response Bundle. This value is a hint to the ACME server for how
long to wait for responses but is not authoritative. The minimum
RTT value SHALL be zero. There is no special significance to
zero-value RTT, it simply indicates the response is expected in
less than the least significant unit used by the ACME client.
{
"rtt": 300.0
}
A challenge response is not sent until the BP agent has been
configured to properly respond to the challenge, so the RTT value is
meant to indicate any node-specific path delays expected to
encountered from the ACME server. Because there is no requirement on
the path (or paths) which bundles may traverse between the ACME
server and the BP agent, and the ACME server can attempt some path
diversity, the RTT value SHOULD be pessimistic.
A default bundle response interval, used when the object does not
contain an RTT, SHOULD be a configurable parameter of the ACME
server. If the ACME client indicated an RTT value in the object, the
response interval SHOULD be twice the RTT (with limiting logic
applied as described below). The lower limit on response interval is
network-specific, but SHOULD NOT be shorter than one second. The
upper limit on response interval is network-specific, but SHOULD NOT
be longer than one minute (60 seconds) for a terrestrial-only DTN.
Sipos Expires 18 May 2022 [Page 12]
Internet-Draft ACME DTN Node ID November 2021
3.3. ACME Node ID Validation Challenge Bundles
Each ACME Node ID Validation Challenge Bundle SHALL be structured and
encoded in accordance with [I-D.ietf-dtn-bpbis].
Each Challenge Bundle has parameters as listed here:
Bundle Processing Control Flags: The primary block flags SHALL
indicate that the payload is an administrative record. The
primary block flags SHALL indicate that user application
acknowledgement is requested; this flag distinguishes the
Challenge Bundle from the Response Bundle. The primary block
flags MAY indicate that status reports are requested; such status
can be helpful to troubleshoot routing issues.
Destination EID: The Destination EID SHALL be the ACME-server-
normalized Node ID being validated.
Source Node ID: The Source Node ID SHALL indicate the Node ID of the
BP agent of the ACME server performing the challenge. The
challenge bundle source SHALL be present in the "source" array of
the challenge object (see Section 3.1)
Creation Timestamp and Lifetime: The Creation Timestamp SHALL be set
to the time at which the challenge was generated. The Lifetime
SHALL indicate the response interval (of Section 3.2) for which
ACME server will accept responses to this challenge.
Administrative Record Type Code: Set to the ACME Node ID Validation
type code defined in Section 8.3.
Administrative Record Content: The Challenge Bundle administrative
record content SHALL consist of a CBOR map containing two pairs:
* One pair SHALL consist of key 1 with value of ACME challenge
token-chal, copied from the challenge object, represented as a
CBOR byte string.
* One pair SHALL consist of key 2 with value of ACME challenge
token-bundle, represented as a CBOR byte string. The token-
bundle is a random value that uniquely identifies the challenge
bundle. This value MUST have at least 128 bits of entropy.
See [RFC4086] for additional information on randomness
requirements.
This structure is part of the extension CDDL in Appendix A. An
example full Challenge Bundle is included in Appendix B.1
Sipos Expires 18 May 2022 [Page 13]
Internet-Draft ACME DTN Node ID November 2021
If the BP agent generating a Challenge Bundle does not have a well-
synchronized clock or the agent responding to the challenge is
expected to not have a well-synchronized clock, the bundle SHALL
include a Bundle Age extension block.
Challenge Bundles SHALL include a Block Integrity Block (BIB) in
accordance with Section 4 or with a Security Source identical to the
bundle Source Node. Challenge Bundles SHALL NOT be directly
encrypted by Block Confidentiality Block (BCB) or any other method
(see Section 7.1).
3.3.1. Challenge Bundle Checks
A proper Challenge Bundle meets all of the following criteria:
* The Challenge Bundle was received within the time interval allowed
for the challenge. The allowed interval starts at the Creation
Timestamp and extends for the Lifetime of the Challenge Bundle.
* The Challenge Bundle Source Node ID is identical to the Node ID
indicated in the ACME challenge object. The comparison of Node
IDs SHALL use the comparison logic of the NODE-ID from
Section 4.4.1 of [I-D.ietf-dtn-tcpclv4].
* The Challenge Bundle contains a BIB which covers at least the
primary block and payload. That BIB has a security source which
is trusted and passes security-context-specific validation (i.e.
MAC or signature verification).
* The challenge payload contains the token-chal as indicated in the
ACME challenge object. The challenge payload contains a token-
bundle meeting the definition in Section 3.3.
Any of the failures above SHALL cause the challenge bundle to be
deleted and otherwise ignored by the BP agent. The BP agent MAY send
status reports about the deletion if allowed by security policy.
3.4. ACME Node ID Validation Response Bundles
Each ACME Node ID Validation Response Bundle SHALL be structured and
encoded in accordance with [I-D.ietf-dtn-bpbis].
Each Response Bundle has parameters as listed here:
Bundle Processing Control Flags: The primary block flags SHALL
indicate that the payload is an administrative record. The
primary block flags SHALL NOT indicate that user application
acknowledgement is requested; this flag distinguishes the Response
Sipos Expires 18 May 2022 [Page 14]
Internet-Draft ACME DTN Node ID November 2021
Bundle from the Challenge Bundle. The primary block flags MAY
indicate that status reports are requested; such status can be
helpful to troubleshoot routing issues.
Destination EID: The Destination EID SHALL be identical to the
Source Node ID of the Challenge Bundle to which this response
corresponds.
Source Node ID: The Source Node ID SHALL be identical to the
Destination EID of the Challenge Bundle to which this response
corresponds.
Creation Timestamp and Lifetime: The Creation Timestamp SHALL be set
to the time at which the response was generated. The response
Lifetime SHALL indicate the response interval remaining if the
Challenge Bundle indicated a limited Lifetime.
Administrative Record Type Code: Set to the ACME Node ID Validation
type code defined in Section 8.3.
Administrative Record Content: The Response Bundle administrative
record content SHALL consist of a CBOR map containing three pairs:
* One pair SHALL consist of key 1 with value of ACME challenge
token-chal, copied from the Request Bundle, represented as a
CBOR byte string.
* One pair SHALL consist of key 2 with value of ACME challenge
token-bundle, copied from the Request Bundle, represented as a
CBOR byte string.
* One pair SHALL consist of key 3 with value of the SHA-256
digest [FIPS180-4] of the ACME Key Authorization in accordance
with Section 8.1 of [RFC8555], represented as a CBOR byte
string.
This structure is part of the extension CDDL in Appendix A. An
example full Response Bundle is included in Appendix B.2
If the BP agent responding to a Challenge Bundle does not have a
well-synchronized clock, it SHALL use any information about last-hop
delays and (if present) Bundle Age extension data to infer the age of
the Challenge Bundle and lifetime of the Response Bundle.
Response Bundles SHALL include a BIB in accordance with Section 4.
Response Bundles SHALL NOT be directly encrypted by BCB or any other
method (see Section 7.1 for explanation).
Sipos Expires 18 May 2022 [Page 15]
Internet-Draft ACME DTN Node ID November 2021
3.4.1. Response Bundle Checks
A proper Response Bundle meets all of the following criteria:
* The Response Bundle was received within the time interval allowed
for the challenge. The allowed interval starts at the Creation
Timestamp and extends for the Lifetime of the associated Challenge
Bundle. The interval of the Challenge Bundle is used here because
the interval of the Response Bundle could be made to disagree with
the Challenge Bundle.
* The Response Bundle Source Node ID is identical to the Node ID
being validated. The comparison of Node IDs SHALL use the
comparison logic of the NODE-ID from Section 4.4.1 of
[I-D.ietf-dtn-tcpclv4].
* The Response Bundle contains a BIB which covers at least the
primary block and payload. That BIB has a security source which
is trusted and passes security-context-specific validation.
* The response payload contains the same token-chal and token-bundle
as sent in the Challenge Bundle (this is also how the two bundles
are correlated). The response payload contains the expected Key
Authorization digest computed by the ACME server.
Any of the failures above SHALL cause that single-perspective
validation to fail. Any of the failures above SHOULD be
distinguished as subproblems to the ACME client. The lack of a
response within the expected response interval, as defined in
Section 3.2, SHALL also be treated as a validation failure.
3.5. Multi-Perspective Validation
To avoid possible on-path attacks in certain networks, an ACME server
can perform a single validation using multiple challenge bundle
sources or via multiple routing paths. This technique is called
multi-perspective validation as recommended in Section 10.2 of
[RFC8555] and an implementation used by Let's Encrypt is described in
[LE-multi-perspective].
When required by policy, an ACME server SHALL send multiple challenge
bundles from different sources in the DTN network. When multiple
Challenge Bundles are sent for a single validation, it is a matter of
ACME server policy to determine whether or not the validation as a
whole is successful. The result of each single-source validation is
defined as success or failure in Section 3.4.1.
Sipos Expires 18 May 2022 [Page 16]
Internet-Draft ACME DTN Node ID November 2021
A RECOMMENDED validation policy is to succeed if the challenge from a
primary bundle source is successful and if there are no more than one
failure from a secondary source. The determination of which
perspectives are considered primary or secondary is an implementation
matter.
Regardless of whether a validation is single- or multi-perspective, a
validation failure SHALL be indicated by an ACME error type of
"incorrectResponse". Each specific perspective failure SHOULD be
indicated to the ACME client as a validation subproblem.
4. Bundle Integrity Gateway
This section defines a BIB use which closely resembles the function
of DKIM email signing [RFC6376]. In this mechanism a routing node in
a DTN sub-network attests to the origination of a bundle by adding a
BIB before forwarding it. The bundle receiver then need not trust
the source of the bundle, but only trust this security source node.
The receiver needs policy configuration to know which security
sources are permitted to attest for which bundle sources.
An integrity gateway SHALL validate the Source Node ID of a bundle,
using local-network-specific means, before adding a BIB to the
bundle. The exact means by which an integrity gateway validates a
bundle's source is network-specific, but could use physical-layer,
network-layer or BP-convergence-layer authentication. The bundle
source could also add its own BIB with a local-network-specific
security context or local-network-specific key material (i.e. a group
key shared within the local network).
When an integrity gateway adds a BIB it SHALL be in accordance with
[I-D.ietf-dtn-bpsec]. The BIB targets SHALL cover both the payload
block and the primary block (either directly as a target or as
additional authenticated data for the payload block MAC/signature).
The Security Source of this BIB SHALL be either the bundle source
Node ID itself or a routing node trusted by the destination node (see
Section 7.2).
5. Certificate Request Profile
The ultimate purpose of this ACME validation is to allow a CA to
issue certificates following the profiles of Section 4.4.2 of
[I-D.ietf-dtn-tcpclv4], [I-D.sipos-dtn-udpcl], and
[I-D.bsipos-dtn-bpsec-cose]. These purposes are referred to here as
bundle security certificates.
Sipos Expires 18 May 2022 [Page 17]
Internet-Draft ACME DTN Node ID November 2021
One defining aspect of bundle security certificates is the Extended
Key Usage key purpose id-kp-bundleSecurity of [IANA-SMI]. When
requesting a certificate which includes a Node ID SAN, the CSR SHOULD
include an Extended Key Usage of id-kp-bundleSecurity. When a bundle
security certificate is issued based on a validated Node ID SAN, the
certificate SHALL include an Extended Key Usage of id-kp-
bundleSecurity.
5.1. Multiple Identity Claims
A single bundle security CSR MAY contain a mixed set of SAN claims,
including combinations of "ip", "dns", and "bundleEID" claims. There
is no restriction on how a certificate combines these claims, but
each claim MUST be validated by an ACME server to issue such a
certificate as part of an associated ACME order. This is no
different than the existing behavior of [RFC8555] but is mentioned
here to make sure that CA policy handles such situations; especially
related to validation failure of an identifier in the presence of
multiple identifiers. The specific use case of
[I-D.ietf-dtn-tcpclv4] allows, and for some network policies
requires, that a certificate authenticate both the DNS name of an
entity as well as the Node ID of the entity.
5.2. Generating Encryption-only or Signing-only Bundle Security
Certificates
ACME extensions specified in this document can be used to request
encryption-only or signing-only bundle security certificates.
In order to request signing only bundle security certificate, the CSR
MUST include the key usage extension with digitalSignature and/or
nonRepudiation bits set and no other bits set.
In order to request encryption only bundle security certificate, the
CSR MUST include the key usage extension with keyEncipherment or
keyAgreement bits set and no other bits set.
Presence of both of the above sets of key usage bits in the CSR, as
well as absence of key usage extension in the CSR, signals to ACME
server to issue a bundle security certificate suitable for both
signing and encryption.
6. Implementation Status
This section is to be removed before publishing as an RFC.
Sipos Expires 18 May 2022 [Page 18]
Internet-Draft ACME DTN Node ID November 2021
[NOTE to the RFC Editor: please remove this section before
publication, as well as the reference to [RFC7942] and
[github-dtn-demo-agent] and [github-dtn-wireshark].]
This section records the status of known implementations of the
protocol defined by this specification at the time of posting of this
Internet-Draft, and is based on a proposal described in [RFC7942].
The description of implementations in this section is intended to
assist the IETF in its decision processes in progressing drafts to
RFCs. Please note that the listing of any individual implementation
here does not imply endorsement by the IETF. Furthermore, no effort
has been spent to verify the information presented here that was
supplied by IETF contributors. This is not intended as, and must not
be construed to be, a catalog of available implementations or their
features. Readers are advised to note that other implementations can
exist.
An example implementation of the this draft of ACME Node ID
Validation has been created as a GitHub project
[github-dtn-demo-agent] and is intended to use as a proof-of-concept
and as a possible source of interoperability testing.
A Wireshark dissector for of the this draft of ACME Node ID
Validation has been created as a GitHub project
[github-dtn-wireshark] and is intended to be used to inspect and
troubleshoot implementations.
7. Security Considerations
This section separates security considerations into threat categories
based on guidance of BCP 72 [RFC3552].
7.1. Threat: Passive Leak of Validation Data
Because this challenge mechanism is used to bootstrap security
between DTN Nodes, the challenge and its response are likely to be
transferred in plaintext. The only ACME data present on-the-wire is
a random token and a cryptographic digest, so there is no sensitive
data to be leaked within the Node ID Validation bundle exchange.
Because each challenge uses a separate token, there is no value in an
on-path attacker seeing the tokens from past challenges and/or
responses.
It is possible for intermediate BP nodes to encapsulate-and-encrypt
Challenge and/or Response Bundles while they traverse untrusted
networks, but that is a DTN configuration matter outside of the scope
of this document.
Sipos Expires 18 May 2022 [Page 19]
Internet-Draft ACME DTN Node ID November 2021
7.2. Threat: BP Node Impersonation
As described in Section 8.1 of [RFC8555], it is possible for an
active attacker to alter data on both ACME client channel and the DTN
validation channel.
The primary mitigation is to delegate bundle integrity sourcing to a
trusted routing node near, in the sense of bundle routing topology,
to the bundle source node as defined in Section 4. This is
functionally similar to DKIM signing of [RFC6376] and provides some
level of bundle origination.
Another way to mitigate single-path on-path attacks is to attempt
validation of the same Node ID from multiple sources or via multiple
bundle routing paths, as defined in Section 3.5. It is not a trivial
task to guarantee bundle routing though, so more advanced techniques
such as onion routing (using bundle-in-bundle encapsulation
[I-D.ietf-dtn-bibect]) could be employed.
7.3. Threat: Bundle Replay
It is possible for an on-path attacker to replay both Challenge
Bundles or Response Bundles. Even in a properly-configured DTN it is
possible that intermediate bundle routers to use multicast forwarding
of a unicast-destination bundle.
Ultimately, the point of the ACME bundle exchange is to derive a Key
Authorization and its cryptographic digest and communicate it back to
the ACME server for validation, so the uniqueness of the Key
Authorization directly determines the scope of replay validity. The
uniqueness of each token-bundle to each challenge bundle ensures that
the Key Authorization is unique to the challenge bundle. The
uniqueness of each token-chal to the ACME challenge ensures that the
Key Authorization is unique to that ACME challenge.
Having each bundle's primary block and payload block covered by a BIB
from a trusted security source (see Section 4) ensures that a
replayed bundle cannot be altered in the blocks used by ACME. All
together, these properties mean that there is no degraded security
caused by replay of either a Challenge Bundle or a Response Bundle
even in the case where the primary or payload block is not covered by
a BIB. The worst that can come of bundle replay is the waste of
network resources as described in Section 7.4.
7.4. Threat: Denial of Service
The behaviors described in this section all amount to a potential
denial-of-service to a BP agent.
Sipos Expires 18 May 2022 [Page 20]
Internet-Draft ACME DTN Node ID November 2021
A malicious entity can continually send Challenge Bundles to a BP
agent. The victim BP agent can ignore Challenge Bundles which do not
conform to the specific time interval and challenge token for which
the ACME client has informed the BP agent that challenges are
expected. The victim BP agent can require all Challenge Bundles to
be BIB-signed to ensure authenticity of the challenge.
A malicious entity can continually send Response Bundles to a BP
agent. The victim BP agent can ignore Response Bundles which do not
conform to the specific time interval or Source Node ID or challenge
token for an active Node ID validation.
Similar to other validation methods, an ACME server validating a DTN
Node ID could be used as a denial of service amplifier. For this
reason any ACME server can rate-limit validation activities for
individual clients and individual certificate requests.
7.5. Inherited Security Considerations
Because this protocol relies on ACME for part of its operation, the
security considerations of [RFC8555] apply to all ACME client--server
exchanges during Node ID validation.
Because this protocol relies on BPv7 for part of its operation, the
security considerations of [I-D.ietf-dtn-bpbis] and
[I-D.ietf-dtn-bpsec] apply to all BP messaging during Node ID
validation.
7.6. Out-of-Scope BP Agent Communication
Although messaging between an ACME client or ACME server an its
associated BP agent are out-of-scope for this document, both of those
channels are critical to Node ID validation security. Either channel
can potentially leak data or provide attack vectors if not properly
secured. These channels need to protect against spoofing of
messaging in both directions to avoid interruption of normal
validation sequencing and to prevent false validations from
succeeding.
The ACME server and its BP agent exchange the outgoing token-chal,
token-bundle, and Key Authorization digest but these values do not
need to be confidential (they are also in plaintext over the BP
channel).
Depending on implementation details, the ACME client might transmit
the client account key thumbprint to its BP agent to allow computing
the Key Authorization digest on the BP agent. If an ACME client does
transmit its client account key thumbprint to a BP agent, it is
Sipos Expires 18 May 2022 [Page 21]
Internet-Draft ACME DTN Node ID November 2021
important that this data is kept confidential because it provides the
binding of the client account key to the Node ID validation (as well
as for all other types of ACME validation). Avoiding this
transmission would require a full round-trip between BP agent and
ACME client, which can be undesirable if the two are separated by a
long-delay network.
8. IANA Considerations
This specification adds to the ACME registry and BP registry for this
behavior.
8.1. ACME Identifier Types
Within the "Automated Certificate Management Environment (ACME)
Protocol" registry [IANA-ACME], the following entry has been added to
the "ACME Identifier Types" sub-registry.
+===========+==================================+
| Label | Reference |
+===========+==================================+
| bundleEID | This specification and [RFC3986] |
+-----------+----------------------------------+
Table 1
8.2. ACME Validation Methods
Within the "Automated Certificate Management Environment (ACME)
Protocol" registry [IANA-ACME], the following entry has been added to
the "ACME Validation Methods" sub-registry.
+===============+=================+======+====================+
| Label | Identifier Type | ACME | Reference |
+===============+=================+======+====================+
| dtn-nodeid-01 | bundleEID | Y | This specification |
+---------------+-----------------+------+--------------------+
Table 2
8.3. Bundle Administrative Record Types
Within the "Bundle Protocol" registry [IANA-BP], the following
entries have been added to the "Bundle Administrative Record Types"
sub-registry.
Sipos Expires 18 May 2022 [Page 22]
Internet-Draft ACME DTN Node ID November 2021
[NOTE to the RFC Editor: For [RFC5050] compatibility the AR-TBD value
needs to be no larger than 15, but such compatibility is not needed.
For BPbis the AR-TBD value needs to be no larger than 65535 as
defined by [I-D.sipos-bpv7-admin-iana].]
+=========================+========+==============+===============+
| Bundle Protocol Version | Value | Description | Reference |
+=========================+========+==============+===============+
| 7 | AR-TBD | ACME Node ID | This |
| | | Validation | specification |
+-------------------------+--------+--------------+---------------+
Table 3
9. Acknowledgments
This specification is based on DTN use cases related to PKIX
certificate issuance.
The workflow and terminology of this validation method was originally
copied from the work of Alexey Melnikov in [RFC8823].
10. References
10.1. Normative References
[FIPS180-4]
National Institute of Standards and Technology, "Secure
Hash Standard (SHS)", FIPS PUB 180-4, August 2015,
<https://csrc.nist.gov/publications/detail/fips/180/4/
final>.
[IANA-ACME]
IANA, "Automated Certificate Management Environment (ACME)
Protocol", <https://www.iana.org/assignments/acme/>.
[IANA-BP] IANA, "Bundle Protocol",
<https://www.iana.org/assignments/bundle/>.
[IANA-SMI] IANA, "Structure of Management Information (SMI) Numbers",
<https://www.iana.org/assignments/smi-numbers/>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
Sipos Expires 18 May 2022 [Page 23]
Internet-Draft ACME DTN Node ID November 2021
[RFC2985] Nystrom, M. and B. Kaliski, "PKCS #9: Selected Object
Classes and Attribute Types Version 2.0", RFC 2985,
DOI 10.17487/RFC2985, November 2000,
<https://www.rfc-editor.org/info/rfc2985>.
[RFC3552] Rescorla, E. and B. Korver, "Guidelines for Writing RFC
Text on Security Considerations", BCP 72, RFC 3552,
DOI 10.17487/RFC3552, July 2003,
<https://www.rfc-editor.org/info/rfc3552>.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66,
RFC 3986, DOI 10.17487/RFC3986, January 2005,
<https://www.rfc-editor.org/info/rfc3986>.
[RFC4086] Eastlake 3rd, D., Schiller, J., and S. Crocker,
"Randomness Requirements for Security", BCP 106, RFC 4086,
DOI 10.17487/RFC4086, June 2005,
<https://www.rfc-editor.org/info/rfc4086>.
[RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data
Encodings", RFC 4648, DOI 10.17487/RFC4648, October 2006,
<https://www.rfc-editor.org/info/rfc4648>.
[RFC4838] Cerf, V., Burleigh, S., Hooke, A., Torgerson, L., Durst,
R., Scott, K., Fall, K., and H. Weiss, "Delay-Tolerant
Networking Architecture", RFC 4838, DOI 10.17487/RFC4838,
April 2007, <https://www.rfc-editor.org/info/rfc4838>.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List
(CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
<https://www.rfc-editor.org/info/rfc5280>.
[RFC7942] Sheffer, Y. and A. Farrel, "Improving Awareness of Running
Code: The Implementation Status Section", BCP 205,
RFC 7942, DOI 10.17487/RFC7942, July 2016,
<https://www.rfc-editor.org/info/rfc7942>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8555] Barnes, R., Hoffman-Andrews, J., McCarney, D., and J.
Kasten, "Automatic Certificate Management Environment
(ACME)", RFC 8555, DOI 10.17487/RFC8555, March 2019,
<https://www.rfc-editor.org/info/rfc8555>.
Sipos Expires 18 May 2022 [Page 24]
Internet-Draft ACME DTN Node ID November 2021
[RFC8610] Birkholz, H., Vigano, C., and C. Bormann, "Concise Data
Definition Language (CDDL): A Notational Convention to
Express Concise Binary Object Representation (CBOR) and
JSON Data Structures", RFC 8610, DOI 10.17487/RFC8610,
June 2019, <https://www.rfc-editor.org/info/rfc8610>.
[I-D.ietf-dtn-bpbis]
Burleigh, S., Fall, K., and E. J. Birrane, "Bundle
Protocol Version 7", Work in Progress, Internet-Draft,
draft-ietf-dtn-bpbis-31, 25 January 2021,
<https://datatracker.ietf.org/doc/html/draft-ietf-dtn-
bpbis-31>.
[I-D.ietf-dtn-bpsec]
III, E. J. B. and K. McKeever, "Bundle Protocol Security
Specification", Work in Progress, Internet-Draft, draft-
ietf-dtn-bpsec-27, 16 February 2021,
<https://datatracker.ietf.org/doc/html/draft-ietf-dtn-
bpsec-27>.
10.2. Informative References
[RFC5050] Scott, K. and S. Burleigh, "Bundle Protocol
Specification", RFC 5050, DOI 10.17487/RFC5050, November
2007, <https://www.rfc-editor.org/info/rfc5050>.
[RFC6376] Crocker, D., Ed., Hansen, T., Ed., and M. Kucherawy, Ed.,
"DomainKeys Identified Mail (DKIM) Signatures", STD 76,
RFC 6376, DOI 10.17487/RFC6376, September 2011,
<https://www.rfc-editor.org/info/rfc6376>.
[RFC8823] Melnikov, A., "Extensions to Automatic Certificate
Management Environment for End-User S/MIME Certificates",
RFC 8823, DOI 10.17487/RFC8823, April 2021,
<https://www.rfc-editor.org/info/rfc8823>.
[I-D.ietf-dtn-bibect]
Burleigh, S., "Bundle-in-Bundle Encapsulation", Work in
Progress, Internet-Draft, draft-ietf-dtn-bibect-03, 18
February 2020, <https://datatracker.ietf.org/doc/html/
draft-ietf-dtn-bibect-03>.
Sipos Expires 18 May 2022 [Page 25]
Internet-Draft ACME DTN Node ID November 2021
[I-D.ietf-dtn-tcpclv4]
Sipos, B., Demmer, M., Ott, J., and S. Perreault, "Delay-
Tolerant Networking TCP Convergence Layer Protocol Version
4", Work in Progress, Internet-Draft, draft-ietf-dtn-
tcpclv4-28, 6 October 2021,
<https://datatracker.ietf.org/doc/html/draft-ietf-dtn-
tcpclv4-28>.
[I-D.sipos-dtn-udpcl]
Sipos, B., "Delay-Tolerant Networking UDP Convergence
Layer Protocol", Work in Progress, Internet-Draft, draft-
sipos-dtn-udpcl-01, 26 March 2021,
<https://datatracker.ietf.org/doc/html/draft-sipos-dtn-
udpcl-01>.
[I-D.sipos-bpv7-admin-iana]
Sipos, B., "Bundle Protocol Version 7 Administrative
Record Types Registry", Work in Progress, Internet-Draft,
draft-sipos-bpv7-admin-iana-00, 13 October 2021,
<https://datatracker.ietf.org/doc/html/draft-sipos-bpv7-
admin-iana-00>.
[I-D.bsipos-dtn-bpsec-cose]
Sipos, B., "DTN Bundle Protocol Security COSE Security
Context", Work in Progress, Internet-Draft, draft-bsipos-
dtn-bpsec-cose-06, 3 June 2021,
<https://datatracker.ietf.org/doc/html/draft-bsipos-dtn-
bpsec-cose-06>.
[github-dtn-demo-agent]
Sipos, B., "Python implementation of basic BPv7-related
protocols",
<https://github.com/BSipos-RKF/dtn-demo-agent/>.
[github-dtn-wireshark]
Sipos, B., "Wireshark Dissectors for BPv7-related
Protocols",
<https://github.com/BSipos-RKF/dtn-wireshark/>.
[LE-multi-perspective]
Aas, J., McCarney, D., and R. Shoemaker, "Multi-
Perspective Validation Improves Domain Validation
Security", 19 February 2020,
<https://letsencrypt.org/2020/02/19/multi-perspective-
validation.html>.
Sipos Expires 18 May 2022 [Page 26]
Internet-Draft ACME DTN Node ID November 2021
Appendix A. Administrative Record Types CDDL
[NOTE to the RFC Editor: The "0xFFFF" in this CDDL is replaced by the
"ACME Node ID Validation" administrative record type code.]
The CDDL extension of BP [I-D.ietf-dtn-bpbis] for the ACME bundles
is:
; All ACME records have the same structure
$admin-record /= [0xFFFF, acme-record]
acme-record = {
token-chal,
token-bundle,
? key-auth-digest ; present for Response Bundles
}
token-chal = (1 => bstr)
token-bundle = (2 => bstr)
key-auth-digest = (3 => bstr)
Appendix B. Example Authorization
[NOTE to the RFC Editor: The "0xFFFF" in these examples are replaced
by the "ACME Node ID Validation" administrative record type code.]
This example is a bundle exchange for the ACME server with Node ID
"dtn://acme-server/" performing a verification for ACME client Node
ID "dtn://acme-client/". The example bundles use no block CRC or
BPSec integrity, which is for simplicity and is not recommended for
normal use. The provided figures are extended diagnostic notation
[RFC8610].
For this example the ACME client key thumbprint has the base64url
encoded value of:
"LPJNul-wow4m6DsqxbninhsWHlwfp0JecwQzYpOLmCQ"
And the ACME-server generated token-chal has the base64url-encoded
value of:
"tPUZNY4ONIk6LxErRFEjVw"
B.1. Challenge Bundle
For the single challenge bundle in this example, the token-bundle
(transported as byte string via BP) has the base64url-encoded value
of:
"p3yRYFU4KxwQaHQjJ2RdiQ"
Sipos Expires 18 May 2022 [Page 27]
Internet-Draft ACME DTN Node ID November 2021
The minimal-but-valid Challenge Bundle is shown in Figure 2. This
challenge requires that the ACME client respond within a 60 second
time window.
[_
[
7, / BP version /
0x22, / flags: user-app-ack, payload-is-an-admin-record /
0, / CRC type: none /
[1, "//acme-client/"], / destination /
[1, "//acme-server/"], / source /
[1, "//acme-server/"], / report-to /
[1000000, 0], / timestamp: 2000-01-01T00:16:40+00:00 /
60000 / lifetime: 60s /
],
[
1, / block type code /
1, / block number /
0, / flags /
0, / CRC type: none /
<<[ / type-specific data /
0xFFFF, / record-type-code /
{ / record-content /
1: b64'tPUZNY4ONIk6LxErRFEjVw' / token-chal /
2: b64'p3yRYFU4KxwQaHQjJ2RdiQ' / token-bundle /
}
]>>
]
]
Figure 2: Example Challenge Bundle
B.2. Response Bundle
When the tokens are combined with the key thumbprint, the full Key
Authorization value (a single string split across lines for
readability) is:
"p3yRYFU4KxwQaHQjJ2RdiQtPUZNY4ONIk6LxErRFEjVw."
"LPJNul-wow4m6DsqxbninhsWHlwfp0JecwQzYpOLmCQ"
The minimal-but-valid Response Bundle is shown in Figure 3. This
response indicates that there is 30 seconds remaining in the response
time window.
Sipos Expires 18 May 2022 [Page 28]
Internet-Draft ACME DTN Node ID November 2021
[_
[
7, / BP version /
0x02, / flags: payload-is-an-admin-record /
0, / CRC type: none /
[1, "//acme-server/"], / destination /
[1, "//acme-client/"], / source /
[1, 0], / report-to: none /
[1030000, 0], / timestamp: 2000-01-01T00:17:10+00:00 /
30000 / lifetime: 30s /
],
[
1, / block type code /
1, / block number /
0, / flags /
0, / CRC type: none /
<<[ / block-type-specific data /
0xFFFF, / record-type-code /
{ / record-content /
1: b64'tPUZNY4ONIk6LxErRFEjVw' / token-chal /
2: b64'p3yRYFU4KxwQaHQjJ2RdiQ' / token-bundle /
3: b64'mVIOJEQZie8XpYM6MMVSQUiNPH64URnhM9niJ5XHrew'
/ key auth. digest /
}
]>>
]
]
Figure 3: Example Response Bundle
Author's Address
Brian Sipos
RKF Engineering Solutions, LLC
7500 Old Georgetown Road
Suite 1275
Bethesda, MD 20814-6198
United States of America
Email: brian.sipos+ietf@gmail.com
Sipos Expires 18 May 2022 [Page 29]