Network Working Group M. Morgenstern
Category: Internet Draft M. Dodge
ECI Telecom
June 2005
Definitions of Managed Objects
for New Generation Asymmetric Digital Subscriber Lines (NG-ADSL)
draft-ietf-adslmib-adsl2-00.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at:
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at:
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2005). All Rights Reserved.
Abstract
This document defines a portion of the Management Information Base
(MIB) module for use with network management protocols in the
Internet community. In particular, it describes objects used for
managing parameters of "Asymmetric Digital Subscriber Line" family
of interface types, especially including ADSL, ADSL2, and ADSL2+.
Expires December 1, 2005 [Page 1]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Table of Contents
1. The Internet-Standard Management Framework .................... 2
2. Overview ...................................................... 2
2.1 Relationship of this MIB Module to other MIB Modules .......... 3
2.2 Conventions used in the MIB Module ............................ 3
2.3 Structure ..................................................... 3
2.4 Persistence ................................................... 4
3. Conformance and Compliance .................................... 4
4. Definitions ................................................... 4
5. Acknowledgements .............................................. 13
6. Security Considerations ....................................... 14
7. IANA Considerations ........................................... 15
8. References .................................................... 15
8.1 Normative References .......................................... 15
8.2 Informative References ........................................ 16
Authors' Addresses ............................................ 16
Full Copyright Statement ...................................... 17
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
2. Overview
This document describes an SNMP MIB module for managing the
ADSL/ADSL2 and ADSL2+ Lines. These definitions are based upon
the specifications for defined in T1E1, European Telecommunications
Standards Institute(ETSI), and International Telecommunication Union
(ITU) documentation [to be added].
Additionally the management framework for New Generation ADSL lines
specified by the Digital Subscriber Line Forum (DSLF) has been taken
into consideration [DSLFTR90].
The MIB module is located in the MIB tree under MIB-2 transmission.
The key words "MUST", "MUST NOT", "RECOMMENDED", and "SHOULD" in this
document are to be interpreted as described in [RFC2119].
Expires December 1, 2005 [Page 2]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
2.1 Relationship of this MIB Module to other MIB Modules
To be added
2.2 Conventions used in the MIB Module
2.2.1 Naming Conventions
A. Atuc -- (ATUC) transceiver at near (Central) end of line
B. Atur -- (ATUR) transceiver at Remote end of line
C. Atu -- One of either Atuc or Atur
D. Curr -- Current
F. Atn -- Attenuation
G. Max -- Maximum
H. Mgn -- Margin
I. PSD -- Power Spectral Density
J. Rx -- Receive
K. Snr -- Signal to Noise Ratio
L. Tx -- Transmit
2.3 Structure
The NG ADSL Line MIB contains the following MIB group:
To be added
2.4 Persistence
All read-create objects defined in this MIB module SHOULD be stored
persistently. Following is an exhaustive list of these persistent
objects:
To be added
Note also that the interface indices in this MIB are maintained
persistently. View-based Access Control Model (VACM) data
relating to these SHOULD be stored persistently as well [RFC3415].
3. Conformance and Compliance
To be added
Expires December 1, 2005 [Page 3]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
4. Definitions
Adsl2-MIB
DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
TimeTicks,
transmission,
Unsigned32,
snmpModules,
Integer32
FROM SNMPv2-SMI
DisplayString,
TEXTUAL-CONVENTION,
ifIndex
FROM IF-MIB
RowStatus
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
adsl2 OBJECT IDENTIFIER ::= { Adsl2 1 }
------------------------------------------------
adsl2Status OBJECT IDENTIFIER ::= { adsl2 1 }
adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 2 }
adsl2Commands OBJECT IDENTIFIER ::= { adsl2 3 }
adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 }
adsl2Config OBJECT IDENTIFIER ::= { adsl2 5 }
adsl2Profile OBJECT IDENTIFIER ::= { adsl2 6 }
------------------------------------------------
adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 }
adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 }
------------------------------------------------
adsl2ConfigLine OBJECT IDENTIFIER ::= { adsl2Config 1 }
------------------------------------------------
adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 }
adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 }
------------------------------------------------
Expires December 1, 2005 [Page 4]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
------------------------------------------------
-- Textual Conventions --
------------------------------------------------
Adsl2YesNo ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
yes (1),
no (2)
}
Adsl2InitResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
noFail(0),
configError(1),
configNotFeasible(2),
commFail(3),
noPeerAtu(4),
otherCause(5)
}
Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A set of ADSL2 line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate
and Lite/splitterless respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved
Expires December 1, 2005 [Page 5]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F)
Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F)
Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F)
Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F)
Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
Bit 39 : G.992.3 Annex M POTS overlapped (F)
Bit 40 : G.992.5 POTS non-overlapped (F)
Bit 41 : G.992.5 POTS overlapped (F)
Bit 42 : G.992.5 ISDN non-overlapped (F)
Bit 43 : G.992.5 ISDN overlapped (F)
Bit 44-45: Reserved
Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
Bit 51 : G.992.5 Annex M POTS overlapped (F)
Bit 52-55: Reserved
"
SYNTAX BITS {
ansit1413(0),
etsi(1),
q9921PotsNonOverlapped(2),
q9921PotsOverlapped(3),
q9921IsdnNonOverlapped(4),
q9921isdnOverlapped(5),
q9921tcmIsdnNonOverlapped(6),
q9921tcmIsdnOverlapped(7),
q9922potsNonOverlapeed(8),
q9922potsOverlapped(9),
q9922tcmIsdnNonOverlapped(10),
q9922tcmIsdnOverlapped(11),
q9921tcmIsdnSymmetric(12),
reserved1(13),
reserved2(14),
reserved3(15),
reserved4(16),
reserved5(17),
q9923PotsNonOverlapped(18),
q9923PotsOverlapped(19),
q9923IsdnNonOverlapped(20),
q9923isdnOverlapped(21),
reserved6(22),
reserved7(23),
Expires December 1, 2005 [Page 6]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
q9924potsNonOverlapeed(24),
q9924potsOverlapped(25),
reserved8(26),
reserved9(27),
q9923AnnexIAllDigNonOverlapped(28),
q9923AnnexIAllDigOverlapped(29),
q9923AnnexJAllDigNonOverlapped(30),
q9923AnnexJAllDigOverlapped(31),
q9924AnnexIAllDigNonOverlapped(32),
q9924AnnexIAllDigOverlapped(33),
q9923AnnexLMode1NonOverlapped(34),
q9923AnnexLMode2NonOverlapped(35),
q9923AnnexLMode3Overlapped(36),
q9923AnnexLMode4Overlapped(37),
q9923AnnexMPotsNonOverlapped(38),
q9923AnnexMPotsOverlapped(39),
q9925PotsNonOverlapped(40),
q9925PotsOverlapped(41),
q9925IsdnNonOverlapped(42),
q9925isdnOverlapped(43),
reserved10(44),
reserved11(45),
q9925AnnexIAllDigNonOverlapped(46),
q9925AnnexIAllDigOverlapped(47),
q9925AnnexJAllDigNonOverlapped(48),
q9925AnnexJAllDigOverlapped(49),
q9925AnnexMPotsNonOverlapped(50),
q9925AnnexMPotsOverlapped(51),
reserved12(52),
reserved13(53),
reserved14(54),
reserved15(55)
}
Adsl2PowerMngState::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
l0(0),
l1(1),
l2(2),
l3(3)
}
Adsl2Unit::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
atuc(1),
atur(2)
}
Expires December 1, 2005 [Page 7]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Adsl2RAMode::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
manual(1),
raInit(2),
dynamicRa(3)
}
Adsl2SymbolProtection::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbol(4)
}
Adsl2MaxBer::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
eminus3(1),
eminus5(2),
eminus7(3)
}
Adsl2EnaDis ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
enabled (1),
disabled (2)
}
Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION ""
SYNTAX INTEGER {
l3toL0 (0),
l0toL2 (2),
l0orL2toL3 (3)
}
Expires December 1, 2005 [Page 8]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"
"
SYNTAX BITS {
bit0(0),bit1(1),bit2(2),bit3(3),bit4(4),bit5(5),
bit6(6),bit7(7),bit8(8),bit9(9),bit10(10),bit11(11),
bit12(12),bit13(13),bit14(14),bit15(15),bit16(16),
bit17(17),bit18(18),bit19(19),bit20(20),bit21(21),
bit22(22),bit23(23),bit24(24),bit25(25),bit26(26),
bit27(27),bit28(28),bit29(29),bit30(30),bit31(31),
bit32(32),bit33(33),bit34(34),bit35(35),bit36(36),
bit37(37),bit38(38),bit39(39),bit40(40),bit41(41),
bit42(42),bit43(43),bit44(44),bit45(45),bit46(46),
bit47(47),bit48(48),bit49(49),bit50(50),bit51(51),
bit52(52),bit53(53),bit54(54),bit55(55),bit56(56),
bit57(57),bit58(58),bit59(59),bit60(60),bit61(61),
bit62(62),bit63(63),bit64(64),bit65(65),bit66(66),
bit67(67),bit68(68),bit69(69),bit70(70),bit71(71),
bit72(72),bit73(73),bit74(74),bit75(75),bit76(76),
bit77(77),bit78(78),bit79(79),bit80(80),bit81(81),
bit82(82),bit83(83),bit84(84),bit85(85),bit86(86),
bit87(87),bit88(88),bit89(89),bit90(90),bit91(91),
bit92(92),bit93(93),bit94(94),bit95(95),bit96(96),
bit97(97),bit98(98),bit99(99),bit100(100),
bit101(101),bit102(102),bit103(103),bit104(104),
bit105(105),bit106(106),bit107(107),bit108(108),
bit109(109),bit110(110),bit111(111),bit112(112),
bit113(113),bit114(114),bit115(115),bit116(116),
bit117(117),bit118(118),bit119(119),bit120(120),
bit121(121),bit122(122),bit123(123),bit124(124),
bit125(125),bit126(126),bit127(127),bit128(128),
bit129(129),bit130(130),bit131(131),bit132(132),
bit133(133),bit134(134),bit135(135),bit136(136),
bit137(137),bit138(138),bit139(139),bit140(140),
bit141(141),bit142(142),bit143(143),bit144(144),
bit145(145),bit146(146),bit147(147),bit148(148),
bit149(149),bit150(150),bit151(151),bit152(152),
bit153(153),bit154(154),bit155(155),bit156(156),
bit157(157),bit158(158),bit159(159),bit160(160),
bit161(161),bit162(162),bit163(163),bit164(164),
bit165(165),bit166(166),bit167(167),bit168(168),
bit169(169),bit170(170),bit171(171),bit172(172),
bit173(173),bit174(174),bit175(175),bit176(176),
bit177(177),bit178(178),bit179(179),bit180(180),
bit181(181),bit182(182),bit183(183),bit184(184),
bit185(185),bit186(186),bit187(187),bit188(188),
bit189(189),bit190(190),bit191(191),bit192(192),
bit193(193),bit194(194),bit195(195),bit196(196),
bit197(197),bit198(198),bit199(199),bit200(200),
bit201(201),bit202(202),bit203(203),bit204(204),
Expires December 1, 2005 [Page 9]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
bit205(205),bit206(206),bit207(207),bit208(208),
bit209(209),bit210(210),bit211(211),bit212(212),
bit213(213),bit214(214),bit215(215),bit216(216),
bit217(217),bit218(218),bit219(219),bit220(220),
bit221(221),bit222(222),bit223(223),bit224(224),
bit225(225),bit226(226),bit227(227),bit228(228),
bit229(229),bit230(230),bit231(231),bit232(232),
bit233(233),bit234(234),bit235(235),bit236(236),
bit237(237),bit238(238),bit239(239),bit240(240),
bit241(241),bit242(242),bit243(243),bit244(244),
bit245(245),bit246(246),bit247(247),bit248(248),
bit249(249),bit250(250),bit251(251),bit252(252),
bit253(253),bit254(254),bit255(255),bit256(256),
bit257(257),bit258(258),bit259(259),bit260(260),
bit261(261),bit262(262),bit263(263),bit264(264),
bit265(265),bit266(266),bit267(267),bit268(268),
bit269(269),bit270(270),bit271(271),bit272(272),
bit273(273),bit274(274),bit275(275),bit276(276),
bit277(277),bit278(278),bit279(279),bit280(280),
bit281(281),bit282(282),bit283(283),bit284(284),
bit285(285),bit286(286),bit287(287),bit288(288),
bit289(289),bit290(290),bit291(291),bit292(292),
bit293(293),bit294(294),bit295(295),bit296(296),
bit297(297),bit298(298),bit299(299),bit300(300),
bit301(301),bit302(302),bit303(303),bit304(304),
bit305(305),bit306(306),bit307(307),bit308(308),
bit309(309),bit310(310),bit311(311),bit312(312),
bit313(313),bit314(314),bit315(315),bit316(316),
bit317(317),bit318(318),bit319(319),bit320(320),
bit321(321),bit322(322),bit323(323),bit324(324),
bit325(325),bit326(326),bit327(327),bit328(328),
bit329(329),bit330(330),bit331(331),bit332(332),
bit333(333),bit334(334),bit335(335),bit336(336),
bit337(337),bit338(338),bit339(339),bit340(340),
bit341(341),bit342(342),bit343(343),bit344(344),
bit345(345),bit346(346),bit347(347),bit348(348),
bit349(349),bit350(350),bit351(351),bit352(352),
bit353(353),bit354(354),bit355(355),bit356(356),
bit357(357),bit358(358),bit359(359),bit360(360),
bit361(361),bit362(362),bit363(363),bit364(364),
bit365(365),bit366(366),bit367(367),bit368(368),
bit369(369),bit370(370),bit371(371),bit372(372),
bit373(373),bit374(374),bit375(375),bit376(376),
bit377(377),bit378(378),bit379(379),bit380(380),
bit381(381),bit382(382),bit383(383),bit384(384),
bit385(385),bit386(386),bit387(387),bit388(388),
bit389(389),bit390(390),bit391(391),bit392(392),
bit393(393),bit394(394),bit395(395),bit396(396),
bit397(397),bit398(398),bit399(399),bit400(400),
bit401(401),bit402(402),bit403(403),bit404(404),
bit405(405),bit406(406),bit407(407),bit408(408),
bit409(409),bit410(410),bit411(411),bit412(412),
Expires December 1, 2005 [Page 10]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
bit413(413),bit414(414),bit415(415),bit416(416),
bit417(417),bit418(418),bit419(419),bit420(420),
bit421(421),bit422(422),bit423(423),bit424(424),
bit425(425),bit426(426),bit427(427),bit428(428),
bit429(429),bit430(430),bit431(431),bit432(432),
bit433(433),bit434(434),bit435(435),bit436(436),
bit437(437),bit438(438),bit439(439),bit440(440),
bit441(441),bit442(442),bit443(443),bit444(444),
bit445(445),bit446(446),bit447(447),bit448(448),
bit449(449),bit450(450),bit451(451),bit452(452),
bit453(453),bit454(454),bit455(455),bit456(456),
bit457(457),bit458(458),bit459(459),bit460(460),
bit461(461),bit462(462),bit463(463),bit464(464),
bit465(465),bit466(466),bit467(467),bit468(468),
bit469(469),bit470(470),bit471(471),bit472(472),
bit473(473),bit474(474),bit475(475),bit476(476),
bit477(477),bit478(478),bit479(479),bit480(480),
bit481(481),bit482(482),bit483(483),bit484(484),
bit485(485),bit486(486),bit487(487),bit488(488),
bit489(489),bit490(490),bit491(491),bit492(492),
bit493(493),bit494(494),bit495(495),bit496(496),
bit497(497),bit498(498),bit499(499),bit500(500),
bit501(501),bit502(502),bit503(503),bit504(504),
bit505(505),bit506(506),bit507(507),bit508(508),
bit509(509),bit510(510),bit511(511)
}
Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"
"
SYNTAX BITS {
bit0(0),bit1(1),bit2(2),bit3(3),bit4(4),bit5(5),
bit6(6),bit7(7),bit8(8),bit9(9),bit10(10),bit11(11),
bit12(12),bit13(13),bit14(14),bit15(15),bit16(16),
bit17(17),bit18(18),bit19(19),bit20(20),bit21(21),
bit22(22),bit23(23),bit24(24),bit25(25),bit26(26),
bit27(27),bit28(28),bit29(29),bit30(30),bit31(31),
bit32(32),bit33(33),bit34(34),bit35(35),bit36(36),
bit37(37),bit38(38),bit39(39),bit40(40),bit41(41),
bit42(42),bit43(43),bit44(44),bit45(45),bit46(46),
bit47(47),bit48(48),bit49(49),bit50(50),bit51(51),
bit52(52),bit53(53),bit54(54),bit55(55),bit56(56),
bit57(57),bit58(58),bit59(59),bit60(60),bit61(61),
bit62(62),bit63(63)
}
Expires December 1, 2005 [Page 11]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
ngadslMIB MODULE-IDENTITY
LAST-UPDATED "200506010000Z" -- June 01, 2005
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: P.O. Box 37324
Raleigh NC 27627-732
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-Chair: Bob Ray
PESA Switching Systems, Inc.
Postal: 330-A Wynn Drive
Huntsville, AL 35805
USA
Email: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Co-editor: Moti Morgenstern
ECI Telecom Ltd.
Postal: 30 hasivim St.
Petach Tikva 49517,
Israel.
Email: moti.morgenstern@ecitele.com
Phone: +972 3 926 6258
Co-editor: Menachem Dodge
ECI Telecom Ltd.
Postal: 30 hasivim St.
Petach Tikva 49517,
Israel.
Email: mbdodge@ieee.org
Phone: +972 3 926 8421
"
------------------------------------------------
-- adsl2LineStatusTable --
------------------------------------------------
adsl2LineStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineStatusTable contains status parameters of ADSL2
line"
::= { adsl2Status 1 }
Expires December 1, 2005 [Page 12]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LineStatusEntry OBJECT-TYPE
SYNTAX Adsl2LineStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineStatusTable contains status parameters of ADSL2
line"
INDEX { adsl2LStatusLineIfIndex }
::= { adsl2LineStatusTable 1 }
Adsl2LineStatusEntry ::=
SEQUENCE {
adsl2LStatusLineIfIndex Unsigned32,
adsl2LStatusAtuTransSys Adsl2TransmissionModeType,
adsl2LStatusPwrMngState Adsl2PowerMngState,
adsl2LStatusInitResult Adsl2InitResult,
adsl2LStatusLastStateDs Unsigned32 (0..10),
adsl2LStatusLastStateUs Unsigned32 (0..10),
adsl2LStatusStatusAtur Unsigned32,
adsl2LStatusStatusAtuc Unsigned32,
adsl2LStatusLnAttenDs Unsigned32,
adsl2LStatusLnAttenUs Unsigned32,
adsl2LStatusSigAttenDs Unsigned32,
adsl2LStatusSigAttenUs Unsigned32,
adsl2LStatusSnrMarginDs Integer32,
adsl2LStatusSnrMarginUs Integer32,
adsl2LStatusAttainableRateDs Unsigned32,
adsl2LStatusAttainableRateUs Unsigned32,
adsl2LStatusActPsdDs Integer32,
adsl2LStatusActPsdUs Integer32,
adsl2LStatusActAtpdDs Integer32,
adsl2LStatusActAtpdUs Integer32
}
adsl2LStatusLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2LineStatusEntry 1 }
Expires December 1, 2005 [Page 13]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LStatusAtuTransSys OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with one bit set to '1'
(the selected coding for the ADSL line).
This parameter may be derived from the handshaking procedures
defined in Recommendation G.994.1.
A set of ADSL2 line transmission modes, with one bit per mode.
The notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F)
Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F)
Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F)
Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F)
Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
Bit 39 : G.992.3 Annex M POTS overlapped (F)
Bit 40 : G.992.5 POTS non-overlapped (F)
Bit 41 : G.992.5 POTS overlapped (F)
Bit 42 : G.992.5 ISDN non-overlapped (F)
Bit 43 : G.992.5 ISDN overlapped (F)
Expires December 1, 2005 [Page 14]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Bit 44-45: Reserved
Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
Bit 51 : G.992.5 Annex M POTS overlapped (F)
Bit 52-55 : Reserved"
::= { adsl2LineStatusEntry 2 }
adsl2LStatusPwrMngState OBJECT-TYPE
SYNTAX Adsl2PowerMngState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current power management state. One of four possible power
management states:
L0 - Synchronized and full transmission (i.e. Showtime),
L1 - Power Down with reduced net data rate (G.992.2 only),
L2 - Power Down with reduced net data rate (G.992.3 and G.992.4
only),
L3 - No power
The various possible values are:L0(0), L1(1), L2(2), L3(3)."
::= { adsl2LineStatusEntry 3 }
adsl2LStatusInitResult OBJECT-TYPE
SYNTAX Adsl2InitResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the result of the last full initialization performed on
the line. It is an enumeration type with the
following values: noFailure(0), configError(1),
configNotFeasible(2),commFail(3), noPeerAtu(4), otherCause(5)."
::= { adsl2LineStatusEntry 4 }
adsl2LStatusLastStateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..10)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in the
downstream direction in the last full initialization
performed on the line. States are per the specific ADSL type
and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime."
::= { adsl2LineStatusEntry 5 }
Expires December 1, 2005 [Page 15]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LStatusLastStateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..10)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in the
upstream direction in the last full initialization performed on the
line. States are per the specific ADSL type and are counted from 0
(if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime."
::= { adsl2LineStatusEntry 6 }
adsl2LStatusStatusAtur OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-R. This is
a bit-map of possible conditions. The various bit positions are:
noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3),
InitFailure(4) - never active on ATU-R"
::= { adsl2LineStatusEntry 7 }
adsl2LStatusStatusAtuc OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-C. This is
a bit-map of possible conditions. The various bit positions are:
noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3),
InitFailure(4)"
::= { adsl2LineStatusEntry 8 }
adsl2LStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub
carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB. (Physical values are 0
to 127 dB). A value of all 1's indicates the line attenuation is
out of range to be represented."
::= { adsl2LineStatusEntry 9 }
Expires December 1, 2005 [Page 16]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub
carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB. (Physical values are 0 to
127 dB). A value of all 1's indicates the line attenuation is out
of range to be represented."
::= { adsl2LineStatusEntry 10 }
adsl2LStatusSigAttenDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub
carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB.
(Physical values are 0 to 127 dB). A value of all 1's indicates the
line attenuation is out of range to be represented."
::= { adsl2LineStatusEntry 11 }
adsl2LStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub
carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB.
(Physical values are 0 to 127 dB). A value of all 1's indicates the
line attenuation is out of range to be represented."
::= { adsl2LineStatusEntry 12 }
adsl2LStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Downstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-R, such that the BER requirements are
met for all downstream bearer channels. It ranges from -640 to 630
units of 0.1 dB. (Physical values are -64 to 63 dB). A value of all
1's indicates the line attenuation is out of range to be
represented."
::= { adsl2LineStatusEntry 13 }
Expires December 1, 2005 [Page 17]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LStatusSnrMarginUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements are
met for all downstream bearer channels.. It ranges from -640 to
630 units of 0.1 dB. (Physical values are -64 to 63 dB).
A value of all 1's indicates the line attenuation is out of
range to be represented."
::= { adsl2LineStatusEntry 14 }
adsl2LStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by the
ATU-C transmitter and the ATU-R receiver, coded in bit/s."
::= { adsl2LineStatusEntry 15 }
adsl2LStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in bit/s."
::= { adsl2LineStatusEntry 16 }
adsl2LStatusActPsdDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB. (Physical
values are -90 to 0 dBm/Hz). A value of all 1's
indicates the measurement is out of range to be represented."
::= { adsl2LineStatusEntry 17 }
Expires December 1, 2005 [Page 18]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LStatusActPsdUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Upstream. The average upstream
transmit PSD over the sub carriers used for upstream. It ranges
from -900 to 0 units of 0.1 dB. (Physical values are -90 to 0
dBm/Hz). A value of all 1's indicates the measurement is out of
range to be represented."
::= { adsl2LineStatusEntry 18 }
adsl2LStatusActAtpdDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Downstream. The total amount of
transmit power delivered by the ATU?C at the U-C reference point,
at the instant of measurement. It ranges from -310 to 310 units of
0.1 dB. (Physical values are -31 to 31 dBm). A value of all 1's
indicates the measurement is out of range to be represented."
::= { adsl2LineStatusEntry 19 }
adsl2LStatusActAtpdUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Upstream. The total amount of
transmit power delivered by the ATU?R at the U-R
reference point, at the instant of measurement. It ranges from
-310 to 310 units of 0.1 dB. (Physical values are -31 to 31 dBm).
A value of all 1's indicates the measurement is out of range to
be represented."
::= { adsl2LineStatusEntry 20 }
------------------------------------------------
-- adsl2ChannelStatusTable --
------------------------------------------------
adsl2ChannelStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2ChannelStatusTable contains status
parameters of ADSL2 channel."
::= { adsl2Status 2 }
Expires December 1, 2005 [Page 19]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChannelStatusEntry OBJECT-TYPE
SYNTAX Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2ChannelStatusTable contains status
parameters of ADSL2 channel."
INDEX { adsl2ChStatusChannelIfIndex, adsl2ChStatusUnit}
::= { adsl2ChannelStatusTable 1 }
Adsl2ChannelStatusEntry ::=
SEQUENCE {
adsl2ChStatusChannelIfIndex Unsigned32,
adsl2ChStatusUnit Adsl2Unit,
adsl2ChStatusActDataRate Unsigned32(0..50000000),
adsl2ChStatusPrevDataRate Unsigned32(0..50000000),
adsl2ChStatusActDelay Unsigned32(0..64),
adsl2ChStatusAtmStatus Unsigned32
}
adsl2ChStatusChannelIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain channel on the
ADSL line on an ATUC board in the system."
::= { adsl2ChannelStatusEntry 1 }
adsl2ChStatusUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit ATUC(1) or ATUR(2)."
::= { adsl2ChannelStatusEntry 2 }
adsl2ChStatusActDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual net data rate the bearer channel is operating at,
if in L0 power management state. In L1 or L2 states, it relates
to the previous L0 state. The data rate is coded in bit/s."
::= { adsl2ChannelStatusEntry 3 }
Expires December 1, 2005 [Page 20]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChStatusPrevDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The previous net data rate the bearer channel was operating at
just before the latest rate change event. This could be a full
or short initialization, fast retrain, DRA or power management
transitions, excluding transitions between L0 state and L1 or
L2 states. The data rate is coded in bit/s."
::= { adsl2ChannelStatusEntry 4 }
adsl2ChStatusActDelay OBJECT-TYPE
SYNTAX Unsigned32(0..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual one-way interleaving delay introduced by the
PMS-TC in the direction of the bearer channel, if in L0
power management state. In L1 or L2 states, it relates to
the previous L0 state. It is coded in ms (rounded to the
nearest ms)."
::= { adsl2ChannelStatusEntry 5 }
adsl2ChStatusAtmStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ADSL channel
in case its Data Path is ATM. This is a bit-map of possible
conditions. The various bit positions are:
noFailure(0),
noCellDelineation(1),
lossOfCellDelineation (2).
In case the channel is not of ATM Data Path the object is set
to '0'."
::= { adsl2ChannelStatusEntry 6 }
------------------------------------------------
-- Adsl2SCStatusTable --
------------------------------------------------
adsl2SCStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2SCStatusTable contains status parameters
of ADSL2 sub carriers."
::= { Adsl2Status 3 }
Expires December 1, 2005 [Page 21]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusEntry OBJECT-TYPE
SYNTAX Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Hfadsl2SCStatusEntry contains status parameters
of ADSL2 sub carriers."
INDEX { adsl2SCStatusLineIfIndex}
::= { adsl2SCStatusTable 1 }
Adsl2SCStatusEntry ::=
SEQUENCE {
adsl2SCStatusLineIfIndex Unsigned32,
adsl2SCStatusSnrDs OCTET STRING ( SIZE (0..512)),
adsl2SCStatusSnrUs OCTET STRING ( SIZE (0..64)),
adsl2SCStatusBitsAllocDs OCTET STRING ( SIZE (0..256)),
adsl2SCStatusBitsAllocUs OCTET STRING ( SIZE (0..32)),
adsl2SCStatusGainAllocDs OCTET STRING ( SIZE (0..1024)),
adsl2SCStatusGainAllocUs OCTET STRING ( SIZE (0..128)),
adsl2SCStatusLinScaleDs Integer32,
adsl2SCStatusLinRealDs OCTET STRING ( SIZE (0..1024)),
adsl2SCStatusLinImgDs OCTET STRING ( SIZE (0..1024)),
adsl2SCStatusLogMtDs Unsigned32,
adsl2SCStatusLogDs OCTET STRING ( SIZE (0..1024)),
adsl2SCStatusLinScaleUs Integer32,
adsl2SCStatusLinRealUs OCTET STRING ( SIZE (0..128)),
adsl2SCStatusLinImgUs OCTET STRING ( SIZE (0..128)),
adsl2SCStatusLogMtUs Unsigned32,
adsl2SCStatusLogUs OCTET STRING ( SIZE (0..128)),
adsl2SCStatusQlnMtDs Unsigned32,
adsl2SCStatusQlnDs OCTET STRING ( SIZE (0..512)),
adsl2SCStatusQlnMtUs Unsigned32,
adsl2SCStatusQlnUs OCTET STRING ( SIZE (0..64)),
adsl2SCStatusLnAttenDs Unsigned32,
adsl2SCStatusLnAttenUs Unsigned32,
adsl2SCStatusSigAttenDs Unsigned32,
adsl2SCStatusSigAttenUs Unsigned32,
adsl2SCStatusSnrMarginDs Integer32,
adsl2SCStatusSnrMarginUs Integer32,
adsl2SCStatusAttainableRateDs Unsigned32,
adsl2SCStatusAttainableRateUs Unsigned32,
adsl2SCStatusActAtpDs Integer32,
adsl2SCStatusActAtpUs Integer32
}
adsl2SCStatusLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
xTUC board in the system."
::= { adsl2SCStatusEntry 1 }
Expires December 1, 2005 [Page 22]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusSnrDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNR Margin per subcarrier, expressing the ratio between the
received signal power and received noise power per subscriber.
An array of 512 bytes, for up to 512 downstream
sub-carriers, depending on NSCds. Byte i (0<=i<NSCds) is set to a
value in the range 0 to 254 to indicate that the respective
downstream sub-carrier i has SNR
of: (-32 + Adsl2SubcarrierSnrDs(i)/2) in dB (i.e., -32 to 95dB).
The special value 255 means that no measurement could be done for
the subcarrier because it is out of the PSD mask passband or that
the noise PSD is out of range to be represented."
::= { adsl2SCStatusEntry 3 }
adsl2SCStatusSnrUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNR Margin per subcarrier, expressing the ratio between the
received signal power and received noise power per subscriber.
An array of 64 bytes, for up to 64 upstream sub-carriers,
depending on NSCus. Byte i (0<=i<NSCus) is set to a value in the
range 0 to 254 to indicate that the respective upstream sub-carrier
i has SNR of: (-32 + Adsl2SubcarrierSnrUs(i)/2) in dB
(i.e., -32 to 95dB). The special value 255 means that no
measurement could be done for the subcarrier because it is out of
the PSD mask passband or that the noise PSD is out of range to
be represented."
::= { adsl2SCStatusEntry 5 }
adsl2SCStatusBitsAllocDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..256))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bits allocation per subcarrier. An array of 256 bytes
(512 nibbles), for up to 512 downstream sub-carriers, depending
on NSCds. Nibble i (0<=i<NSCds) is set to a value in the range
0 to 15 to indicate that the respective downstream sub-carrier
i has the same amount of bits allocation."
::= { adsl2SCStatusEntry 6 }
Expires December 1, 2005 [Page 23]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusBitsAllocUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bits allocation per subcarrier. An array of 32 bytes
(64 nibbles), for up to 64 upstream sub-carriers, depending on
NSCus. Nibble i (0<=i<NSCus) is set to a value in the range 0
to 15 to indicate that the respective upstream sub-carrier i
has the same amount of bits allocation."
::= { adsl2SCStatusEntry 7 }
adsl2SCStatusGainAllocDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The gain allocation per subcarrier. An array of 512 16-bits
values, for up to 512 downstream sub-carriers, depending on NSCds.
Value i (0<=i<NSCds) is in the range 0 to 4093 to indicate that
the respective downstream sub-carrier i has the same amount of gain
value. The gain value is represented as a multiple of 1/512 on
linear scale."
::= { adsl2SCStatusEntry 8 }
adsl2SCStatusGainAllocUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The gain allocation per subcarrier. An array of 64 16-bits values,
for up to 64 upstream sub-carriers, depending on NSCus.
Value i (0<=i<NSCus) is in the range 0 to 4093 to indicate that the
respective upstream sub-carrier i has the same amount of gain
value. The gain value is represented as a multiple of 1/512 on
linear scale."
::= { adsl2SCStatusEntry 9 }
adsl2SCStatusLinScaleDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The scale factor to be applied to the downstream H(f) linear
representation values. This parameter is only available after a
loop diagnostic procedure."
::= { adsl2SCStatusEntry 10 }
Expires December 1, 2005 [Page 24]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusLinRealDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 512 complex downstream H(f) linear representation
values in linear scale for up to 512 downstream sub-carriers,
depending on NSCds. Each array entry represents the real component
[referred here as a(i)] of Hlin(f = i*Df) value for a particular
sub-carrier index i (0<=i<NSCds). Hlin(f) is represented as
((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is
Adsl2SubcarrierLinScaleDs and a(i) and b(i) [provided by the
Adsl2SubcarrierLinDsImg object] are in the range (-2^15+1) to
(+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the passband
or that the attenuation is out of range to be represented. This
parameter is only available after a loop diagnostic procedure."
::= { adsl2SCStatusEntry 11 }
adsl2SCStatusLinImgDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 512 complex downstream H(f) linear representation
values in linear scale for up to 512 downstream sub-carriers,
depending on NSCds. Each array entry represents the imaginary
component [referred here as b(i)] of Hlin(f = i*Df) value for
a particular sub-carrier index i (0<=i<NSCds).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScaleDs and a(i) [provided by
the Adsl2SubcarrierLinDsReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates
that no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure."
::= { adsl2SCStatusEntry 12 }
adsl2SCStatusLogMtDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the downstream H(f)
logarithmic measurement values. This parameter should correspond
to the value specified in the recommendation (e.g. the number of
symbols in 1 s. time interval for G.992.3). This parameter
corresponds to 1 second in loop diagnostic procedure and should be
updated in initialization"
::= { adsl2SCStatusEntry 13 }
Expires December 1, 2005 [Page 25]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusLogDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 512 real downstream H(f) logarithmic representation
values in dB for up to 512 downstream sub-carriers, depending on
NSCds. Each array entry represents the real Hlog(f = i*Df) value
for a particular sub-carrier index i, (0<=i<NSCds).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in
the range 0 to 1022. A special value m=1023 indicates that no
measurement could be done for the subcarrier because it is out of
the passband or that the attenuation is out of range to be
represented. This parameter is applicable in loop diagnostic
procedure and initialization."
::= { adsl2SCStatusEntry 14 }
adsl2SCStatusLinScaleUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The scale factor to be applied to the upstream H(f) linear
representation values. This parameter is only available after a
loop diagnostic procedure."
::= { adsl2SCStatusEntry 15 }
adsl2SCStatusLinRealUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 64 complex upstream H(f) linear representation values
in linear scale for up to 64 upstream sub-carriers, depending on
NSCus. Each array entry represents the real component [referred
here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier
index i (0<=i<NSCus). Hlin(f) is represented as
((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is
Adsl2SubcarrierLinScaleUs and a(i) and b(i) [provided by the
Adsl2SubcarrierLinUsImg object] are in the range (-2^15+1) to
(+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no
measurement could be done for the subcarrier because it is out of
the passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure."
::= { adsl2SCStatusEntry 16 }
Expires December 1, 2005 [Page 26]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusLinImgUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 64 complex upstream H(f) linear representation values
in linear scale for up to 64 upstream sub-carriers, depending on
NSCus. Each array entry represents the imaginary component
[referred here as b(i)] of Hlin(f = i*Df) value for a particular
sub-carrier index i (0<=i<NSCus). Hlin(f) is represented as
((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is
Adsl2SubcarrierLinScaleUs and a(i) [provided by the
Adsl2SubcarrierLinUsReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15
indicates that no measurement could be done for the subcarrier
because it is out of the passband or that the attenuation is out
of range to be represented. This parameter is only available after
a loop diagnostic procedure."
::= { adsl2SCStatusEntry 17 }
adsl2SCStatusLogMtUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the upstream H(f)
logarithmic measurement values. This parameter should correspond
to the value specified in the recommendation (e.g. the number of
symbols in 1 s. time interval for G.992.3). This parameter
corresponds to 1 second in loop diagnostic procedure and should be
updated in initializationis "
::= { adsl2SCStatusEntry 18 }
adsl2SCStatusLogUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 64 real upstream H(f) logarithmic representation
values in dB for up to 64 upstream sub-carriers, depending on
NSCus. Each array entry represents the real Hlog(f = i*Df) value
for a particular sub-carrier index i, (0<=i<NSCus). The real
Hlog(f) value is represented as (6-m(i)/10), with m(i) in the
range 0 to 1022. A special value m=1023 indicates that no
measurement could be done for the subcarrier because it is out of
the passband or that the attenuation is out of range to be
represented. This parameter is applicable in loop diagnostic
procedure and initialization."
::= { adsl2SCStatusEntry 19 }
Expires December 1, 2005 [Page 27]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusQlnMtDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the downstream Quiet Line
Noise values. This parameter should correspond to the value
specified in the recommendation (e.g. the number of symbols in
1 s. time interval for G.992.3). This parameter corresponds to
1 second in loop diagnostic procedure and should be updated in
initialization "
::= { adsl2SCStatusEntry 20 }
adsl2SCStatusQlnDs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 512 real downstream Quiet Line Noise values in dB for
up to 512 downstream sub-carriers, depending on NSCds. Each array
entry represents the QLN(f = i*Df) value for a particular
subcarrier index i, (0<=i<NSCds). The QLN(f) is represented as
( -23-n(i)/2), with n(i) in the range 0 to 254. A special value
n(i)=255 indicates that no measurement could be done for the
subcarrier because it is out of the passband or that the noise PSD
is out of range to be represented. This parameter is applicable
in loop diagnostic procedure and initialization."
::= { adsl2SCStatusEntry 21 }
adsl2SCStatusQlnMtUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the upstream Quiet Line
Noise values. This parameter should correspond to the value
specified in the recommendation (e.g. the number of symbols in
1 s. time interval for G.992.3). This parameter corresponds to 1
second in loop diagnostic procedure and should be updated in
initializationis updated after a loop diagnostic procedure."
::= { adsl2SCStatusEntry 22 }
Expires December 1, 2005 [Page 28]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusQlnUs OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of 64 real upstream Quiet Line Noise values in dB for up
to 64 upstream sub-carriers, depending on NSCus. Each array entry
represents the QLN(f = i*Df) value for a particular sub-carrier
index i, (0<=i<NSCus). The QLN(f) is represented as (-23-n(i)/2),
with n(i) in the range 0 to 254. A special value n(i)=255
indicates that no measurement could be done for the subcarrier
because it is out of the passband or that the noise PSD is out of
range to be represented. This parameter is applicable in loop
diagnostic procedure and initialization."
::= { adsl2SCStatusEntry 23 }
adsl2SCStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub
carriers during diagnostics mode and initialization. It ranges
from 0 to 1270 units of 0.1 dB. (Physical values are 0 to 127 dB).
A value of all 1's indicates the line attenuation is out of range
to be represented."
::= { adsl2SCStatusEntry 24 }
adsl2SCStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub
carriers during diagnostics mode and initialization. It ranges
from 0 to 1270 units of 0.1 dB. (Physical values are 0 to 127 dB).
A value of all 1's indicates the line attenuation is out of range
to be represented."
::= { adsl2SCStatusEntry 25 }
adsl2SCStatusSigAttenDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub
carriers during Showtime. It ranges from 0 to 1270 units of 0.1
dB. (Physical values are 0 to 127 dB). A value of all 1's
indicates the line attenuation is out of range to be represented."
::= { adsl2SCStatusEntry 26 }
Expires December 1, 2005 [Page 29]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub
carriers during Showtime. It ranges from 0 to 1270 units of 0.1
dB. (Physical values are 0 to 127 dB). A value of all 1's
indicates the line attenuation is out of range to be represented."
::= { adsl2SCStatusEntry 27 }
adsl2SCStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Margin is the maximum increase in dB of the noise power
received at the ATU-R, such that the BER requirements are met for
all bearer channels received at the ATU-R. It ranges from -640 to
630 units of 0.1 dB. (Physical values are -64 to 63 dB). A value
of all 1's indicates the SNR margin is out of range to be
represented."
::= { adsl2SCStatusEntry 28 }
adsl2SCStatusSnrMarginUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Margin is the maximum increase in dB of the noise power
received at the ATU-C, such that the BER requirements are met for
all bearer channels received at the ATU-C. It ranges from -640 to
630 units of 0.1 dB. (Physical values are -64 to 63 dB). A value
of all 1's indicates the SNR margin is out of range to be
represented."
::= { adsl2SCStatusEntry 29 }
adsl2SCStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate currently
attainable by the ATU-C transmitter and ATU-R receiver, coded in
bit/s."
::= { adsl2SCStatusEntry 30 }
Expires December 1, 2005 [Page 30]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2SCStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate currently
attainable by the ATU-R transmitter and ATU-C receiver, coded in
bit/s."
::= { adsl2SCStatusEntry 31 }
adsl2SCStatusActAtpDs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power from the ATU-C. The total amount
of transmit-power delivered at either the U-C (ATU-C) reference
point, at the instant of measurement. It ranges from -310 to 310
units of 0.1 dB. (Physical values are -31 to 31 dBm). A value of
all 1's indicates the measurement is out of range to be
represented."
::= { adsl2SCStatusEntry 32 }
adsl2SCStatusActAtpUs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power from the ATU-R. The total amount
of transmit-power delivered at either the U-C (ATU-R) reference
point, at the instant of measurement. It ranges from -310 to 310
units of 0.1 dB. (Physical values are -31 to 31 dBm). A value of
all 1's indicates the measurement is out of range to be
represented."
::= { adsl2SCStatusEntry 33 }
------------------------------------------------
-- adsl2LineInventoryTable --
------------------------------------------------
adsl2LineInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineInventoryTable contains inventory of ADSL2
unit."
::= { adsl2Inventory 1 }
Expires December 1, 2005 [Page 31]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LineInventoryEntry OBJECT-TYPE
SYNTAX Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineInventoryTable contains inventory of ADSL2
unit."
INDEX { adsl2LInvLineIfIndex ,adsl2LInvUnit }
::= { adsl2LineInventoryTable 1 }
Adsl2LineInventoryEntry ::=
SEQUENCE {
adsl2LInvLineIfIndex Unsigned32,
adsl2LInvUnit Adsl2Unit,
adsl2LInvG994VendorId OCTET STRING ( SIZE (0..8)),
adsl2LInvSystemVendorId OCTET STRING ( SIZE (0..8)),
adsl2LInvVersionNumber OCTET STRING ( SIZE (0..16)),
adsl2LInvSerialNumber OCTET STRING ( SIZE (0..32)),
adsl2LInvSelfTestResult OCTET STRING ( SIZE (0..4)),
adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType
}
adsl2LInvLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain channel on the ADSL
line on an ATUC board in the system."
::= { adsl2LineInventoryEntry 1 }
adsl2LInvUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit ATUC{1} or ATUR{2}."
::= { adsl2LineInventoryEntry 2 }
adsl2LInvG994VendorId OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR
message. It consists of 8 binary octets, including a country code
followed by a (regionally allocated) provider code, as defined in
Recommendation T.35."
::= { adsl2LineInventoryEntry 3 }
Expires December 1, 2005 [Page 32]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LInvSystemVendorId OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU System Vendor ID (identifies the ATU system integrator) as
inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It consists of 8 binary octets, with same
format as used for Adsl2InvG994VendorId."
::= { adsl2LineInventoryEntry 4 }
adsl2LInvVersionNumber OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU version number (vendor specific information) as inserted
in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in
the Embedded Operations Channel (only ATU-R in G.992.1 and
G.992.2). It consists of up to 16 binary octets"
::= { adsl2LineInventoryEntry 5 }
adsl2LInvSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU serial number (vendor specific information) as inserted in
the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in
the Embedded Operations Channel (only ATU-R in G.992.1 and
G.992.2). It is vendor specific information. It consists of up to
32 ASCII characters."
::= { adsl2LineInventoryEntry 6 }
adsl2LInvSelfTestResult OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE (0..4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU self-test result, coded as a 32-bit integer. The most
significant octet of this object is '0' if the self-test passed
and '1' if the self-test failed. The interpretation of the other
octets is vendor discretionary."
::= { adsl2LineInventoryEntry 7 }
Expires December 1, 2005 [Page 33]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LInvTransmissionCapabilities OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU transmission system capability list of the different
coding types. It is coded in a bit-map representation with 1 or
more bits set. A bit set to '1' means that the ATU supports the
respective coding. The value may be derived from the handshaking
procedures defined in G.994.1.
A set of ADSL2 line transmission modes, with one bit per mode. The
notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F)
Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow
U/S (F)
Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F)
Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F)
Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
Bit 39 : G.992.3 Annex M POTS overlapped (F)
Bit 40 : G.992.5 POTS non-overlapped (F)
Bit 41 : G.992.5 POTS overlapped (F)
Bit 42 : G.992.5 ISDN non-overlapped (F)
Bit 43 : G.992.5 ISDN overlapped (F)
Expires December 1, 2005 [Page 34]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Bit 44-45: Reserved
Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
Bit 51 : G.992.5 Annex M POTS overlapped (F)
Bit 52-55 : Reserved"
::= { adsl2LineInventoryEntry 8 }
------------------------------------------------
-- adsl2LineCommandTable --
------------------------------------------------
adsl2LineCommandTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineCommandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineCommandTable provides tools t execute command
on ADSL2 line level."
::= { adsl2Commands 1 }
adsl2LineCommandEntry OBJECT-TYPE
SYNTAX Adsl2LineCommandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineCommandTable contains the assignment of ADSL2
profile to line."
INDEX { adsl2LCmndLineIfIndex }
::= { adsl2LineCommandTable 1 }
Adsl2LineCommandEntry ::=
SEQUENCE {
adsl2LCmndLineIfIndex Unsigned32,
adsl2LCmndConfPmsf Adsl2ConfPmsForce,
adsl2LCmndConfLdsf Adsl2YesNo,
adsl2LCmndConfLdsfFailReason Unsigned32
}
adsl2LCmndLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2LineCommandEntry 1 }
Expires December 1, 2005 [Page 35]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LCmndConfPmsf OBJECT-TYPE
SYNTAX Adsl2ConfPmsForce
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Power management state forced. Defines the line states to be
forced by the near-end ATU on this line. The various possible
values are:
L3toL0 (0),
L0toL2 (2),
L0orL2toL3 (3)."
::= { adsl2LineCommandEntry 2 }
adsl2LCmndConfLdsf OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Loop diagnostics mode forced (LDSF). Defines whether the line
should be forced into the loop diagnostics mode by the near-end
ATU on this line or only be responsive to loop diagnostics
initiated by the far-end ATU. The various possible values are:
Yes{1}, No{2}"
::= { adsl2LineCommandEntry 4 }
adsl2LCmndConfLdsfFailReason OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the recent occasion the Loop diagnostics mode forced
(LDSF) was issued for the associated line. Possible values are:
None {1} - The default value in case LDSF was never requested for
the associated line.
Success {2} - The recent command completed successfully.
InProgress {3} - The Loop Diagnostics process is in progress.
Unsupported {4} - The NE or the line card doesn't support LDSF.
CannotRun {5} - The NE cannot initiate the command, due to a non
specific reason.
Aborted {6} - The Loop Diagnostics process aborted.
Failed {7} - The Loop Diagnostics process failed.
IllegalMode {8} - The NE cannot initiate the command, due to the
specific mode of the relevant line.
AdminUp {9} - The NE cannot initiate the command, as the relevant
line is administratively 'Up'."
::= { adsl2LineCommandEntry 6 }
------------------------------------------------
-- adsl2LineConfigTable --
------------------------------------------------
Expires December 1, 2005 [Page 36]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LineConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfigTable contains the assignment of ADSL2
profile to line."
::= { adsl2ConfigLine 1 }
adsl2LineConfigEntry OBJECT-TYPE
SYNTAX Adsl2LineConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfigTable contains the assignment of ADSL2
profile to line."
INDEX { adsl2LCnfgLineIfIndex }
::= { adsl2LineConfigTable 1 }
Adsl2LineConfigEntry ::=
SEQUENCE {
adsl2LCnfgLineIfIndex Unsigned32,
adsl2LCnfgLineTemplate SnmpAdminString
}
adsl2LCnfgLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain channel on the ADSL
line on an ATUC board in the system."
::= { adsl2LineConfigEntry 1 }
adsl2LCnfgLineTemplate OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Configuration Templates Table, (Adsl2ConfTemplatesTable), which
applies for this ADSL2 line."
::= { adsl2LineConfigEntry 2 }
------------------------------------------------
-- adsl2LineConfTemplateTable --
------------------------------------------------
Expires December 1, 2005 [Page 37]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LineConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfTemplateTable contains ADSL2 line
configuration template."
::= { adsl2ProfileLine 1 }
adsl2LineConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfTemplateTable contains ADSL2 line
configuration template."
INDEX { adsl2LConfTempTemplateName }
::= { adsl2LineConfTemplateTable 1 }
Adsl2LineConfTemplateEntry ::=
SEQUENCE {
adsl2LConfTempTemplateName SnmpAdminString ,
adsl2LConfTempLineProfile SnmpAdminString,
adsl2LConfTempChan1ConfProfile SnmpAdminString,
adsl2LConfTempChan1RaRatioDs Unsigned32(0..100),
adsl2LConfTempChan1RaRatioUs Unsigned32(0..100),
adsl2LConfTempChan2ConfProfile SnmpAdminString,
adsl2LConfTempChan2RaRatioDs Unsigned32(0..100),
adsl2LConfTempChan2RaRatioUs Unsigned32(0..100),
adsl2LConfTempChan3ConfProfile SnmpAdminString,
adsl2LConfTempChan3RaRatioDs Unsigned32(0..100),
adsl2LConfTempChan3RaRatioUs Unsigned32(0..100),
adsl2LConfTempChan4ConfProfile SnmpAdminString,
adsl2LConfTempChan4RaRatioDs Unsigned32(0..100),
adsl2LConfTempChan4RaRatioUs Unsigned32(0..100),
adsl2LConfTempRowStatus RowStatus
}
adsl2LConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineConfTemplateEntry 1 }
Expires December 1, 2005 [Page 38]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Configuration Profile Table, (Adsl2LineConfProfileTable), which
applies for this ADSL2 line."
::= { adsl2LineConfTemplateEntry 2 }
adsl2LConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Channel
Configuration Profile Table, (Adsl2ChanConfProfileTable), which
applies for ADSL2 bearer channel #1. If channel is unused then
the object is set to Null.."
::= { adsl2LineConfTemplateEntry 3 }
adsl2LConfTempChan1RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #1 when performing rate adaptation
on Downstream. The ratio refers to the available data rate in
excess of the Minimum Data Rate summed over all bearer channels.
Also, the 1- Adsl2ConfTemplateChan1RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels on
Downstream direction.The sum of rate adaptation ratios over all
bearers on the same direction shall be equal to 100%."
::= { adsl2LineConfTemplateEntry 4 }
adsl2LConfTempChan1RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #1 when performing rate adaptation
on Upstream. The ratio refers to the available data rate in excess
of the Minimum Data Rate summed over all bearer channels. Also,
the 1- Adsl2ConfTemplateChan1RaRatioUs is the ratio of excess data
rate to be assigned to all other bearer channels on Upstream
direction.The sum of rate adaptation ratios over all bearers on
the same direction shall be equal to 100 %."
::= { adsl2LineConfTemplateEntry 5 }
Expires December 1, 2005 [Page 39]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Channel
Configuration Profile Table, (Adsl2ChanConfProfileTable), which
applies for ADSL2 bearer channel #2. If channel is unused then
the object is set to Null."
::= { adsl2LineConfTemplateEntry 6 }
adsl2LConfTempChan2RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #2 when performing rate adaptation
on Downstream. The ratio refers to the available data rate in
excess of the Minimum Data Rate summed over all bearer channels.
Also, the 1- Adsl2ConfTemplateChan2RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels on
Downstream direction.The sum of rate adaptation ratios over all
bearers on the same direction shall be equal to 100%."
::= { adsl2LineConfTemplateEntry 7 }
adsl2LConfTempChan2RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #2 when performing rate adaptation
on Upstream. The ratio refers to the available data rate in excess
of the Minimum Data Rate summed over all bearer channels. Also,
the 1- Adsl2ConfTemplateChan2RaRatioUs is the ratio of excess data
rate to be assigned to all other bearer channels on Upstream
direction.The sum of rate adaptation ratios over all bearers on
the same direction shall be equal to 100 %."
::= { adsl2LineConfTemplateEntry 8 }
adsl2LConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Channel
Configuration Profile Table, (Adsl2ChanConfProfileTable), which
applies for ADSL2 bearer channel #3. If channel is unused then
the object is set to Null."
::= { adsl2LineConfTemplateEntry 9 }
Expires December 1, 2005 [Page 40]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfTempChan3RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #3 when performing rate adaptation
on Downstream. The ratio refers to the available data rate in
excess of the Minimum Data Rate summed over all bearer channels.
Also, the 1- Adsl2ConfTemplateChan3RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels on
Downstream direction.The sum of rate adaptation ratios over all
bearers on the same direction shall be equal to 100%."
::= { adsl2LineConfTemplateEntry 10 }
adsl2LConfTempChan3RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #3 when performing rate adaptation
on Upstream. The ratio refers to the available data rate in excess
of the Minimum Data Rate summed over all bearer channels. Also,
the 1- Adsl2ConfTemplateChan3RaRatioUs is the ratio of excess data
rate to be assigned to all other bearer channels on Upstream
direction.The sum of rate adaptation ratios over all bearers on
the same direction shall be equal to 100%."
::= { adsl2LineConfTemplateEntry 11 }
adsl2LConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Channel
Configuration Profile Table, (Adsl2ChanConfProfileTableDs), which
applies for ADSL2 bearer channel #4. If channel is unused Then the
object is set to Null."
::= { adsl2LineConfTemplateEntry 12 }
adsl2LConfTempChan4RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #4 when performing rate adaptation
on Downstream. The ratio refers to the available data rate in
excess of the Minimum Data Rate summed over all bearer channels.
Also, the 1- Chan4RaRatio is the ratio of excess data rate to be
assigned to all other bearer channels.The sum of rate adaptation
ratios over all bearers on the same direction shall sum to 100%."
::= { adsl2LineConfTemplateEntry 13 }
Expires December 1, 2005 [Page 41]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfTempChan4RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken into
account for the bearer channel #4 when performing rate adaptation
on Upstream. The ratio refers to the available data rate in
excess of the Minimum Data Rate summed over all bearer channels.
Also, the 1- Chan4RaRatio is the ratio of excess data rate to be
assigned to all other bearer channels.The sum of rate adaptation
ratios over all bearers on the same direction shall sum to 100%."
::= { adsl2LineConfTemplateEntry 14 }
adsl2LConfTempRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Row Status."
::= { adsl2LineConfTemplateEntry 15 }
------------------------------------------
-- adsl2LineConfProfTable --
------------------------------------------
adsl2LineConfProfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfProfTable contains ADSL2 line profile
configuration."
::= { adsl2ProfileLine 3 }
adsl2LineConfProfEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2LineConfProfTable contains ADSL2 line profile
configuration."
INDEX { adsl2LConfProfProfileName }
::= { adsl2LineConfProfTable 1 }
Adsl2LineConfProfEntry ::=
SEQUENCE {
adsl2LConfProfProfileName SnmpAdminString,
adsl2LConfProfScMaskDs Adsl2ScMaskDs,
adsl2LConfProfScMaskUs Adsl2ScMaskUs,
adsl2LConfProfRaModeDs Adsl2RAMode,
adsl2LConfProfRaModeUs Adsl2RAMode,
adsl2LConfProfRaUsNrmDs Unsigned32(0..310),
Expires December 1, 2005 [Page 42]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfRaUsNrmUs Unsigned32(0..310),
adsl2LConfProfRaUsTimeDs Unsigned32(0..16383),
adsl2LConfProfRaUsTimeUs Unsigned32(0..16383),
adsl2LConfProfRaDsNrmsDs Unsigned32(0..310),
adsl2LConfProfRaDsNrmsUs Unsigned32(0..310),
adsl2LConfProfRaDsTimeDs Unsigned32(0..16383),
adsl2LConfProfRaDsTimeUs Unsigned32(0..16383),
adsl2LConfProfTargetSnrmDs Unsigned32(0..310),
adsl2LConfProfTargetSnrmUs Unsigned32(0..310),
adsl2LConfProfMaxSnrmDs Unsigned32,
adsl2LConfProfMaxSnrmUs Unsigned32,
adsl2LConfProfMinSnrmDs Unsigned32(0..310),
adsl2LConfProfMinSnrmUs Unsigned32(0..310),
adsl2LConfProfMsgMinUs Unsigned32(4000..64000),
adsl2LConfProfMsgMinDs Unsigned32(4000..64000),
adsl2LConfProfAtuTransSysEna Adsl2TransmissionModeType,
adsl2LConfProfPmMode Unsigned32,
adsl2LConfProfL0Time Unsigned32(0..255),
adsl2LConfProfL2Time Unsigned32(0..255),
adsl2LConfProfL2Atpr Unsigned32(0..31),
adsl2LConfProfL2Atprt Unsigned32(0..31),
adsl2LConfProfMaxNomPsdDs Integer32(-600..-400),
adsl2LConfProfMaxNomPsdUs Integer32(-600..-380),
adsl2LConfProfMaxNomAtpDs Unsigned32(0..255),
adsl2LConfProfMaxNomAtpUs Unsigned32(0..255),
adsl2LConfProfMaxNomRxPwrUs Integer32(-255..2147483647),
adsl2LConfProfRowStatus RowStatus
}
adsl2LConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineConfProfEntry 1 }
adsl2LConfProfScMaskDs OBJECT-TYPE
SYNTAX Adsl2ScMaskDs
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 512 bits, that allows masking up
to 512 downstream sub-carriers, depending on NSCds. If bit i
(0<=i<NSCds) is set to '1' the respective downstream sub-carrier i
is masked and if set to '0' the respective sub-carrier is
unmasked. Note that there should be always unmasked sub carriers
(i.e., the object cannot be all 1's). Also note that in case
NSCds<512 all bits i (NSCds <i<=512) should be set to '1'."
::= { adsl2LineConfProfEntry 2 }
Expires December 1, 2005 [Page 43]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfScMaskUs OBJECT-TYPE
SYNTAX Adsl2ScMaskUs
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 64 bits, that allows masking up to
64 downstream sub-carriers, depending on NSCds. If bit i
(0<=i<NSCus) is set to '1' the respective upstream sub-carrier i
is masked and if set to '0' the respective sub-carrier is
unmasked. Note that there should be always unmasked sub carriers
(i.e., the object cannot be all 1's). Also note that in case
NSCus<64 all bits i (NSCus <i<=64) should be set to '1'."
::= { adsl2LineConfProfEntry 3 }
adsl2LConfProfRaModeDs OBJECT-TYPE
SYNTAX Adsl2RAMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU?C in the transmit
direction. The parameter can take three values:
Manual (1),
RaInit (2),
DynamicRa (3)."
::= { adsl2LineConfProfEntry 5 }
adsl2LConfProfRaModeUs OBJECT-TYPE
SYNTAX Adsl2RAMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU?R in the transmit
direction. The parameter can take three values:
Manual (1),
RaInit (2),
DynamicRa (3)."
::= { adsl2LineConfProfEntry 6 }
adsl2LConfProfRaUsNrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Downstream Up-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream
noise margin is above this value and stays above that for more
than the time specified by the Adsl2LineConfRaUsTimeDs, the
ATU?R shall attempt to increase the downstream net data rate. The
Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1
dB. (Physical values are 0 to 31 dB). "
::= { adsl2LineConfProfEntry 7 }
Expires December 1, 2005 [Page 44]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfRaUsNrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Upstream Up-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise
margin is above this value and stays above that for more than the
time specified by the Adsl2LineConfRaUsTimeUs, the ATU?C shall
attempt to increase the upstream net data rate. The Upstream
Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB.
(Physical values are 0 to 31 dB)."
::= { adsl2LineConfProfEntry 8 }
adsl2LConfProfRaUsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Downstream Up-Shift Time Interval, to be used when
Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time
the downstream noise margin should stay above the Downstream
Up-shift Noise Margin before the ATU?R shall attempt to increase
the downstream net data rate. The time interval ranges from 0 to
16383 seconds."
::= { adsl2LineConfProfEntry 9 }
adsl2LConfProfRaUsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Upstream Up-Shift Time Interval, to be used when
Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time
the upstream noise margin should stay above the Upstream
Up-shift Noise Margin before the ATU?C shall attempt to increase
the upstream net data rate. The time interval ranges from 0 to
16383 seconds."
::= { adsl2LineConfProfEntry 10 }
adsl2LConfProfRaDsNrmsDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Downstream Down-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise
margin is below this value and stays below that for more than the
time specified by the Adsl2LineConfRaDsTimeDs, the ATU?R shall
attempt to decrease the downstream net data rate. The Downstream
Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB.
(Physical values are 0 to 31 dB)."
::= { adsl2LineConfProfEntry 11 }
Expires December 1, 2005 [Page 45]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfRaDsNrmsUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Upstream Downshift Noise Margin value, to be used when
Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise
margin is below this value and stays below that for more than the
time specified by the Adsl2LineConfRaDsTimeUs, the ATU?C shall
attempt to decrease the upstream net data rate. The Upstream
Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB.
(Physical values are 0 to 31 dB)."
::= { adsl2LineConfProfEntry 12 }
adsl2LConfProfRaDsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Downstream Downshift Time Interval, to be used when
Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time the
downstream noise margin should stay below the Downstream Down-shift
Noise Margin before the ATU?R shall attempt to decrease the
downstream net data rate. The time interval ranges from 0 to 16383
seconds."
::= { adsl2LineConfProfEntry 13 }
adsl2LConfProfRaDsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Upstream Down-Shift Time Interval, to be used when
Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time
the upstream noise margin should stay below the Upstream
Down-shift Noise Margin before the ATU?C shall attempt to decrease
the upstream net data rate. The time interval ranges from 0 to
16383 seconds."
::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfTargetSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Noise Margin the ATU?R receiver shall achieve, relative to
the BER requirement for each of the downstream bearer channels, or
better, to successfully complete initialization. The target noise
margin ranges from 0 to 310 units of 0.1 dB. (Physical values are
0 to 31 dB)."
::= { adsl2LineConfProfEntry 15 }
Expires December 1, 2005 [Page 46]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfTargetSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Noise Margin the ATU?C receiver shall achieve, relative to the
BER requirement for each of the upstream bearer channels, or
better, to successfully complete initialization. The target noise
margin ranges from 0 to 310 units of 0.1 dB. (Physical values are
0 to 31 dB)."
::= { adsl2LineConfProfEntry 16 }
adsl2LConfProfMaxSnrmDs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU?R receiver shall try to sustain.
If the Noise Margin is above this level, the ATU-R shall request
the ATU?C to reduce the ATU?C transmit power to get a noise margin
below this limit (if this functionality is supported). The
maximum noise margin ranges from 0 to 310 units of 0.1 dB.
(Physical values are 0 to 31 dB). A value of all 1's means that
there is no maximum."
::= { adsl2LineConfProfEntry 17 }
adsl2LConfProfMaxSnrmUs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU?C receiver shall try to sustain.
If the Noise Margin is above this level, the ATU-C shall request
the ATU?R to reduce the ATU?R transmit power to get a noise
margin below this limit (if this functionality is supported). The
maximum noise margin ranges from 0 to 310 units of 0.1 dB.
(Physical values are 0 to 31 dB). A value of all 1's means that
there is no maximum."
::= { adsl2LineConfProfEntry 18 }
adsl2LConfProfMinSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU?R receiver shall tolerate. If the
noise margin falls below this level, the ATU-R shall request the
ATU?C to increase the ATU?C transmit power. If an increase to
ATU-C transmit power is not possible, a loss-of-margin (LOM)
defect occurs, the ATU?R shall fail and attempt to reinitialize
and the NMS shall be notified. The minimum noise margin ranges
from 0 to 310 units of 0.1 dB. (Physical values are 0 to 31 dB).
A value of 0 means that there is no minimum."
Expires December 1, 2005 [Page 47]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
::= { adsl2LineConfProfEntry 19 }
adsl2LConfProfMinSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU?C receiver shall tolerate. If
the noise margin falls below this level, the ATU-C shall request
the ATU?R to increase the ATU?R transmit power. If an increase of
ATU?R transmit power is not possible, a loss-of-margin (LOM)
defect occurs, the ATU?C shall fail and attempt to re?initialize
and the NMS shall be notified. The minimum noise margin ranges
from 0 to 310 units of 0.1 dB. (Physical values are 0 to 31 dB).
A value of 0 means that there is no minimum.."
::= { adsl2LineConfProfEntry 20 }
adsl2LConfProfMsgMinUs OBJECT-TYPE
SYNTAX Unsigned32(4000..64000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Overhead Rate Upstream. Defines the minimum rate of the
message-based overhead that shall be maintained by the ATU in
upstream direction. Expressed in bits per second and ranges from
4000 to 64000 bps."
::= { adsl2LineConfProfEntry 21 }
adsl2LConfProfMsgMinDs OBJECT-TYPE
SYNTAX Unsigned32(4000..64000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Overhead Rate Downstream. Defines the minimum rate of the
message-based overhead that shall be maintained by the ATU in
downstream direction. Expressed in bits per second and ranges
from 4000 to 64000 bps. "
::= { adsl2LineConfProfEntry 22 }
adsl2LConfProfAtuTransSysEna OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"ATU Transmission System Enabling (ATSE). A list of the different
coding types enabled in this profile. It is coded in a bit-map
representation with 1 or more bits set. A bit set to '1' means
that the ATUs may apply the respective coding for the ADSL line.
A bit set to '0' means that the ATUs cannot apply the respective
coding for the ADSL line. All 'reserved' bits should be set to
'0'."
::= { adsl2LineConfProfEntry 23 }
Expires December 1, 2005 [Page 48]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfPmMode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Power management state Enabling. Defines the line states the ATU-C
or ATU-R may autonomously transition to on this line. The various
bit positions are: L3state (0), L1_2state (1)A bit with a '1'
value means that the ATU is allowed to transit into the respective
state and a '0' value means that the ATU is not allowed to transit
into the respective state."
::= { adsl2LineConfProfEntry 24 }
adsl2LConfProfL0Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Exit from the L2 state
and the next Entry into the L2 state. It ranges from 0 to 255
seconds."
::= { adsl2LineConfProfEntry 25 }
adsl2LConfProfL2Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This minimum time (in seconds) between:
*An Entry into the L2 state and the first Power Trim in the L2
state and *Between two consecutive Power Trims in the L2 State. It
ranges from 0 to 255 seconds."
::= { adsl2LineConfProfEntry 26 }
adsl2LConfProfL2Atpr OBJECT-TYPE
SYNTAX Unsigned32 (0..31)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum aggregate transmit power reduction (in dB) that can be
performed through a single Power Trim in the L2 state. It ranges
from 0 dB to 31 dB."
::= { adsl2LineConfProfEntry 27 }
adsl2LConfProfL2Atprt OBJECT-TYPE
SYNTAX Unsigned32 (0..31)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum aggregate transmit power reduction (in dB) that can
be performed at a transition from L0 into L2 state or through a
single Power Trim in the L2 state. It ranges from 0 dB to 31 dB."
::= { adsl2LineConfProfEntry 28 }
Expires December 1, 2005 [Page 49]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfMaxNomPsdDs OBJECT-TYPE
SYNTAX Integer32(-600..-400)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the downstream direction
during initialization and Showtime. It ranges from -600 to -400
units of 0.1 dBm/Hz. (physical values are -60 to -40 dBm/Hz).
There should be multiple MAXNOMPSDds parameters in the profile in
case multiple bits are set in Adsl2LineConfAtse."
::= { adsl2LineConfProfEntry 29 }
adsl2LConfProfMaxNomPsdUs OBJECT-TYPE
SYNTAX Integer32(-600..-380)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the upstream direction during
initialization and Showtime. It ranges from -600 to -380 units of
0.1 dBm/Hz. (physical values are -60 to -38 dBm/Hz).There should
be multiple MAXNOMPSDus parameters in the profile in case multiple
bits are set in Adsl2LineConfAtse."
::= { adsl2LineConfProfEntry 30 }
adsl2LConfProfMaxNomAtpDs OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the downstream
direction during initialization and Showtime. It ranges from 0 to
255 units of 0.1 dBm (physical values are 0 to 25.5 dBm)."
::= { adsl2LineConfProfEntry 31 }
adsl2LConfProfMaxNomAtpUs OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from 0 to
255 units of 0.1 dBm (physical values are 0 to 25.5 dBm)."
::= { adsl2LineConfProfEntry 32 }
adsl2LConfProfMaxNomRxPwrUs OBJECT-TYPE
SYNTAX Integer32(-255..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum upstream aggregate receive power over the relevant set
of sub-carriers. The ATU-C should verify that the upstream power
cutback is such that this maximum aggregate receive power value is
honored. It ranges from -255 to 255 units of 0.1 dBm (physical
values are -25.5 to 25.5 dBm). A value of all ones means that
there is no limit."
::= { adsl2LineConfProfEntry 33 }
Expires December 1, 2005 [Page 50]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2LConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Row Status"
::= { adsl2LineConfProfEntry 36 }
------------------------------------------------
-- adsl2ChConfProfileTable --
------------------------------------------------
adsl2ChConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel profile
configuration."
::= { adsl2ProfileChannel 1 }
adsl2ChConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2ChConfProfileTable contains ADSL2 channel profile
configuration."
INDEX { adsl2ChConfProfProfileName }
::= { adsl2ChConfProfileTable 1 }
Adsl2ChConfProfileEntry ::=
SEQUENCE {
adsl2ChConfProfProfileName SnmpAdminString,
adsl2ChConfProfMinDataRateDs Unsigned32(0..50000000),
adsl2ChConfProfMinDataRateUs Unsigned32(0..50000000),
adsl2ChConfProfMinResDataRateDs Unsigned32(0..50000000),
adsl2ChConfProfMinResDataRateUs Unsigned32(0..50000000),
adsl2ChConfProfMaxDataRateDs Unsigned32(0..50000000),
adsl2ChConfProfMaxDataRateUs Unsigned32(0..50000000),
adsl2ChConfProfMinDataRateLowPwrDs Unsigned32(0..50000000),
adsl2ChConfProfMinDataRateLowPwrUs Unsigned32(0..50000000),
Expires December 1, 2005 [Page 51]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChConfProfMaxDelayDs Unsigned32(0..64),
adsl2ChConfProfMaxDelayUs Unsigned32(0..64),
adsl2ChConfProfMinProtectionDs Adsl2SymbolProtection,
adsl2ChConfProfMinProtectionUs Adsl2SymbolProtection,
adsl2ChConfProfMaxBerDs Adsl2MaxBer,
adsl2ChConfProfMaxBerUs Adsl2MaxBer,
adsl2ChConfProfUsDataRateDs Unsigned32(0..50000000),
adsl2ChConfProfDsDataRateDs Unsigned32(0..50000000),
adsl2ChConfProfUsDataRateUs Unsigned32(0..50000000),
adsl2ChConfProfDsDataRateUs Unsigned32(0..50000000),
adsl2ChConfProfImaEnabled Adsl2EnaDis,
adsl2ChConfProfRowStatus RowStatus
}
adsl2ChConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChConfProfileEntry 1 }
adsl2ChConfProfMinDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Data Rate on Downstream direction. The minimum net data
rate for the bearer channel, coded in bit/s."
::= { adsl2ChConfProfileEntry 2 }
adsl2ChConfProfMinDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Data Rate on Upstream direction. The minimum net data
rate for the bearer channel, coded in bit/s."
::= { adsl2ChConfProfileEntry 3 }
adsl2ChConfProfMinResDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Downstream direction. The minimum
reserved net data rate for the bearer channel, coded in bit/s.
This parameter is used only if the Rate Adaptation Mode in the
direction of the bearer channel (i.e., Adsl2LineConfRaModeDs)
is set to DynamicRa."
::= { adsl2ChConfProfileEntry 4 }
Expires December 1, 2005 [Page 52]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChConfProfMinResDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Upstream direction. The minimum
reserved net data rate for the bearer channel, coded in
bit/s. This parameter is used only if the Rate Adaptation Mode in
the direction of the bearer channel (i.e., Adsl2LineConfRaModeUs)
is set to DynamicRa."
::= { adsl2ChConfProfileEntry 5 }
adsl2ChConfProfMaxDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Data Rate on Downstream direction. The maximum net data
rate for the bearer channel, coded in bit/s."
::= { adsl2ChConfProfileEntry 6 }
adsl2ChConfProfMaxDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Data Rate on Upstream direction. The maximum net data
rate for the bearer channel, coded in bit/s."
::= { adsl2ChConfProfileEntry 7 }
adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Data Rate in Low Power state on Downstream direction. The
minimum net data rate for the bearer channel, coded in bit/s.,
during the low power state (L1 in G.992.2, L2 in G.992.3)."
::= { adsl2ChConfProfileEntry 8 }
adsl2ChConfProfMinDataRateLowPwrUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Data Rate in Low Power state on Upstream direction. The
minimum net data rate for the bearer channel, coded in bit/s.,
during the low power state (L1 in G.992.2, L2 in G.992.3)."
::= { adsl2ChConfProfileEntry 9 }
Expires December 1, 2005 [Page 53]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChConfProfMaxDelayDs OBJECT-TYPE
SYNTAX Unsigned32(0..64)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on Downstream
direction.. The ATUs shall choose the S (factor) and D (depth)
values such that the actual one-way interleaving delay
(Adsl2ChanStatusActDelay) is as close to but less or equal than
Adsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value
0 indicating no delay bound is being imposed."
::= { adsl2ChConfProfileEntry 10 }
adsl2ChConfProfMaxDelayUs OBJECT-TYPE
SYNTAX Unsigned32(0..64)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on Upstream
direction.. The ATUs shall choose the S (factor) and D (depth)
values such that the actual one-way interleaving delay
(Adsl2ChanStatusActDelay) is as close to but less or equal than
Adsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value
0 indicating no delay bound is being imposed."
::= { adsl2ChConfProfileEntry 11 }
adsl2ChConfProfMinProtectionDs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel, expressed
in symbols. The parameter can take the following values:
NoProtection (1),
HalfSymbol (2),
SingleSymbol (3),
TwoSymbols (4)."
::= { adsl2ChConfProfileEntry 12 }
adsl2ChConfProfMinProtectionUs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel, expressed
in symbols. The parameter can take the following values:
NoProtection (1),
HalfSymbol (2),
SingleSymbol (3),
TwoSymbols (4)"
Expires December 1, 2005 [Page 54]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
::= { adsl2ChConfProfileEntry 13 }
adsl2ChConfProfMaxBerDs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Downstream direction. The maximum bit
error ratio for the bearer channel. The parameter can take the
following values (for 1E-3, 1E-5 or 1E-7):
Eminus3 (1),
Eminus5 (2),
Eminus7 (3)"
::= { adsl2ChConfProfileEntry 14 }
adsl2ChConfProfMaxBerUs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Upstream direction. The maximum bit
error ratio for the bearer channel. The parameter can take the
following values (for 1E-3, 1E-5 or 1E-7):
Eminus3 (1),
Eminus5 (2),
Eminus7 (3)"
::= { adsl2ChConfProfileEntry 15 }
adsl2ChConfProfUsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for downstream direction. An
'Up-shift rate change' event is triggered when the actual
downstream data rate exceeds, by more than the threshold, the data
rate at the last entry into Showtime. The parameter is coded in
bit/s."
::= { adsl2ChConfProfileEntry 16 }
adsl2ChConfProfDsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Data Rate Threshold Downshift for downstream direction. A
'Down-shift rate change' event is triggered when the actual
downstream data rate is below the data rate at the last entry into
Showtime, by more than the threshold. The parameter is coded in
bit/s."
::= { adsl2ChConfProfileEntry 17 }
Expires December 1, 2005 [Page 55]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2ChConfProfUsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for upstream direction. An 'Up-shift
rate change' event is triggered when the actual
upstream data rate exceeds, by more than the threshold, the data
rate at the last entry into Showtime. The parameter is coded in
bit/s."
::= { adsl2ChConfProfileEntry 18 }
adsl2ChConfProfDsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..50000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Data Rate Threshold Downshift for upstream direction. A
'Down-shift rate change' event is triggered when the actual
upstream data rate is below the data rate at the last entry into
Showtime, by more than the threshold. The parameter is coded in
bit/s."
::= { adsl2ChConfProfileEntry 19 }
adsl2ChConfProfImaEnabled OBJECT-TYPE
SYNTAX Adsl2EnaDis
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IMA Mode Enable. The parameter enables the IMA operation mode in
the ATM Data Path. Relevant only if the channel is of ATM Data
Path. When in 'enable' state the ATM data path should comply with
the requirements for IMA transmission."
::= { adsl2ChConfProfileEntry 20 }
adsl2ChConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Row Status"
::= { adsl2ChConfProfileEntry 21 }
--
--PM line current counters
--
adsl2PMLineCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line."
::= {adsl2PMLine 1}
Expires December 1, 2005 [Page 56]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLineCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line."
INDEX { adsl2PMLCurrLineIfIndex, adsl2PMLCurrUnit }
::= { adsl2PMLineCurrTable 1 }
Adsl2PMLineCurrEntry ::=
SEQUENCE {
adsl2PMLCurrLineIfIndex Unsigned32,
adsl2PMLCurrUnit Adsl2Unit,
adsl2PMLCurrValidIntervals Unsigned32,
adsl2PMLCurrInvalidIntervals Unsigned32,
adsl2PMLCurr15MTimeElapsed Unsigned32,
adsl2PMLCurr15MFecSeconds Unsigned32,
adsl2PMLCurr15MEs Unsigned32,
adsl2PMLCurr15MSes Unsigned32,
adsl2PMLCurr15MLoss Unsigned32,
adsl2PMLCurr15MUas Unsigned32,
adsl2PMLCurr1DayValidIntervals Unsigned32,
adsl2PMLCurr1DayInvalidIntervals Unsigned32,
adsl2PMLCurr1DayTimeElapsed Unsigned32,
adsl2PMLCurr1DayFecSeconds Unsigned32,
adsl2PMLCurr1DayEs Unsigned32,
adsl2PMLCurr1DaySes Unsigned32,
adsl2PMLCurr1DayLoss Unsigned32,
adsl2PMLCurr1DayUas Unsigned32
}
adsl2PMLCurrLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain
ADSL line on an ATUC board in the system."
::= { adsl2PMLineCurrEntry 1 }
adsl2PMLCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit ATUC{1} or ATUR{2}."
::= { adsl2PMLineCurrEntry 2 }
Expires December 1, 2005 [Page 57]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 3 }
adsl2PMLCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 4 }
adsl2PMLCurr15MTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval"
::= { adsl2PMLineCurrEntry 5 }
adsl2PMLCurr15MFecSeconds OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was at least one
FEC correction event for one or more bearer channels in this line.
This parameter is inhibited during UAS or SES."
::= { adsl2PMLineCurrEntry 6 }
adsl2PMLCurr15MEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR
SEF >=1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR
RDI >=1 OR LPR-FE >=1
This parameter is inhibited during UAS."
::= { adsl2PMLineCurrEntry 7 }
Expires December 1, 2005 [Page 58]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLCurr15MSes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1
OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1
OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
::= { adsl2PMLineCurrEntry 8 }
adsl2PMLCurr15MLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was LOS (or
LOS-FE for ATU-R)."
::= { adsl2PMLineCurrEntry 9 }
adsl2PMLCurr15MUas OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely
errored seconds, and ends at the onset of 10 contiguous seconds
with no severely errored seconds."
::= { adsl2PMLineCurrEntry 10 }
adsl2PMLCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 11 }
adsl2PMLCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 12 }
Expires December 1, 2005 [Page 59]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { adsl2PMLineCurrEntry 13 }
adsl2PMLCurr1DayFecSeconds OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was at least one
FEC correction event for one or more bearer channels in this line.
This parameter is inhibited during UAS or SES."
::= { adsl2PMLineCurrEntry 14 }
adsl2PMLCurr1DayEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR
SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1
OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
::= { adsl2PMLineCurrEntry 15 }
adsl2PMLCurr1DaySes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1
OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
::= { adsl2PMLineCurrEntry 16 }
adsl2PMLCurr1DayLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was LOS (or
LOS-FE for ATU-R)."
::= { adsl2PMLineCurrEntry 17 }
Expires December 1, 2005 [Page 60]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLCurr1DayUas OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely
errored seconds, and ends at the onset of 10 contiguous seconds
with no severely errored seconds."
::= { adsl2PMLineCurrEntry 18 }
--
--PM line init current counters
--
adsl2PMLineInitTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitTable contains current initialization
counters of ADSL2 line."
::= {adsl2PMLine 2}
adsl2PMLineInitEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitTable contains current initialization
counters of ADSL2 line. ."
INDEX { adsl2PMLInitLineIfIndex }
::= { adsl2PMLineInitTable 1 }
Adsl2PMLineInitEntry ::=
SEQUENCE {
adsl2PMLInitLineIfIndex Unsigned32,
adsl2PMLInit15MfullInits Unsigned32,
adsl2PMLInit15MfailedFullInits Unsigned32,
adsl2PMLInit15MShortInits Unsigned32,
adsl2PMLInit15MFailedShortInits Unsigned32,
adsl2PMLInit1DayFullInits Unsigned32,
adsl2PMLInit1DayFailedFullInits Unsigned32,
adsl2PMLInit1DayShortInits Unsigned32,
adsl2PMLInit1DayFailedShortInits Unsigned32
}
Expires December 1, 2005 [Page 61]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLInitLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2PMLineInitEntry 1 }
adsl2PMLInit15MfullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitEntry 2 }
adsl2PMLInit15MfailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
::= { adsl2PMLineInitEntry 3 }
adsl2PMLInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitEntry 4 }
adsl2PMLInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
::= { adsl2PMLineInitEntry 5 }
adsl2PMLInit1DayFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitEntry 6 }
Expires December 1, 2005 [Page 62]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLInit1DayFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
::= { adsl2PMLineInitEntry 7 }
adsl2PMLInit1DayShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitEntry 8 }
adsl2PMLInit1DayFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
::= { adsl2PMLineInitEntry 9 }
--
--PM line history 15M
--
adsl2PMLineHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineHist15MinTable contains PM line history for
15min intervals of ADSL2 line."
::= {adsl2PMLine 3}
adsl2PMLineHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineHist15MinTable contains PM line history for
15min intervals of ADSL2 line ."
INDEX { adsl2PMLHist15MLineIfIndex, adsl2PMLHist15MUnit,
adsl2PMLHist15MInterval }
::= { adsl2PMLineHist15MinTable 1 }
Expires December 1, 2005 [Page 63]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Adsl2PMLineHist15MinEntry ::=
SEQUENCE {
adsl2PMLHist15MLineIfIndex Unsigned32,
adsl2PMLHist15MUnit Adsl2Unit,
adsl2PMLHist15MInterval Unsigned32,
adsl2PMLHist15MMonitoredTime Unsigned32,
adsl2PMLHist15MFecSeconds Unsigned32,
adsl2PMLHist15MEs Unsigned32,
adsl2PMLHist15MSes Unsigned32,
adsl2PMLHist15MLoss Unsigned32,
adsl2PMLHist15MUas Unsigned32,
adsl2PMLHist15MValidInterval Adsl2YesNo
}
adsl2PMLHist15MLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2PMLineHist15MinEntry 1 }
adsl2PMLHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit ATUC{1} or ATUR{2}."
::= { adsl2PMLineHist15MinEntry 2 }
adsl2PMLHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist15MinEntry 3 }
adsl2PMLHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist15MinEntry 4 }
Expires December 1, 2005 [Page 64]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLHist15MFecSeconds OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was at least one
FEC correction event for one or more bearer channels in this line.
This parameter is inhibited during UAS or SES."
::= { adsl2PMLineHist15MinEntry 5 }
adsl2PMLHist15MEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR
SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1
OR RDI >= 1 OR LPR-FE >=1
This parameter is inhibited during UAS."
::= { adsl2PMLineHist15MinEntry 6 }
adsl2PMLHist15MSes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1
OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS.."
::= { adsl2PMLineHist15MinEntry 7 }
adsl2PMLHist15MLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was LOS (or
LOS-FE for ATU-R)."
::= { adsl2PMLineHist15MinEntry 8 }
adsl2PMLHist15MUas OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely
errored seconds, and ends at the onset of 10 contiguous seconds
Expires December 1, 2005 [Page 65]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
with no severely errored seconds."
::= { adsl2PMLineHist15MinEntry 9 }
adsl2PMLHist15MValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information?"
::= { adsl2PMLineHist15MinEntry 10 }
--
--PM line hist 1D
--
adsl2PMLineHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineHist1DayTable contains PM line history for
24 hours intervals of ADSL2 line."
::= {adsl2PMLine 4}
adsl2PMLineHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineHist1DayTable contains PM line history for
24 hours intervals of ADSL2 line."
INDEX { adsl2PMLHist1DLineIfIndex, adsl2PMLHist1DUnit,
adsl2PMLHist1DInterval }
::= { adsl2PMLineHist1DayTable 1 }
Adsl2PMLineHist1DayEntry ::=
SEQUENCE {
adsl2PMLHist1DLineIfIndex Unsigned32,
adsl2PMLHist1DUnit Adsl2Unit,
adsl2PMLHist1DInterval Unsigned32,
adsl2PMLHist1DMonitoredTime Unsigned32,
adsl2PMLHist1DFecSeconds Unsigned32,
adsl2PMLHist1DEs Unsigned32,
adsl2PMLHist1DSes Unsigned32,
adsl2PMLHist1DLoss Unsigned32,
adsl2PMLHist1DUas Unsigned32,
adsl2PMLHist1DValidInterval Adsl2YesNo
}
adsl2PMLHist1DLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
Expires December 1, 2005 [Page 66]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2PMLineHist1DayEntry 1 }
adsl2PMLHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMLineHist1DayEntry 2 }
adsl2PMLHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist1DayEntry 3 }
adsl2PMLHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist1DayEntry 4 }
adsl2PMLHist1DFecSeconds OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was at least one
FEC correction event for one or more bearer channels in this line.
This parameter is inhibited during UAS or SES."
::= { adsl2PMLineHist1DayEntry 5 }
adsl2PMLHist1DEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR
SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1
OR RDI >= 1 OR LPR-FE >=1
This parameter is inhibited during UAS."
::= { adsl2PMLineHist1DayEntry 6 }
adsl2PMLHist1DSes OBJECT-TYPE
SYNTAX Unsigned32
Expires December 1, 2005 [Page 67]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1
OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
::= { adsl2PMLineHist1DayEntry 7 }
adsl2PMLHist1DLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there was LOS (or
LOS-FE for ATU-R)."
::= { adsl2PMLineHist1DayEntry 8 }
adsl2PMLHist1DUas OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely
errored seconds, and ends at the onset of 10 contiguous seconds
with no severely errored seconds."
::= { adsl2PMLineHist1DayEntry 9 }
adsl2PMLHist1DValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information?"
::= { adsl2PMLineHist1DayEntry 10 }
--
--PM line init list 15M
--
adsl2PMLineInitHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15 minutes intervals of ADSL2 line."
::= {adsl2PMLine 5}
Expires December 1, 2005 [Page 68]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMLineInitHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15 minutes intervals of ADSL2 line."
INDEX {adsl2PMLHistInit15MLineIfIndex,
adsl2PMLHistInit15MInterval}
::= { adsl2PMLineInitHist15MinTable 1 }
Adsl2PMLineInitHist15MinEntry ::=
SEQUENCE {
adsl2PMLHistInit15MLineIfIndex Unsigned32,
adsl2PMLHistInit15MInterval Unsigned32,
adsl2PMLHistInit15MFullInits Unsigned32,
adsl2PMLHistInit15MFailedFullInits Unsigned32,
adsl2PMLHistInit15MShortInits Unsigned32,
adsl2PMLHistInit15MFailedShortInits Unsigned32,
adsl2PMLHistInit15MValidInterval Adsl2YesNo
}
adsl2PMLHistInit15MLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an ATUC
board in the system."
::= { adsl2PMLineInitHist15MinEntry 1 }
adsl2PMLHistInit15MInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist15MinEntry 2 }
adsl2PMLHistInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitHist15MinEntry 3 }
adsl2PMLHistInit15MFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
Expires December 1, 2005 [Page 69]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
::= { adsl2PMLineInitHist15MinEntry 4 }
adsl2PMLHistInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitHist15MinEntry 5 }
adsl2PMLHistInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
::= { adsl2PMLineInitHist15MinEntry 6 }
adsl2PMLHistInit15MValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information?."
::= { adsl2PMLineInitHist15MinEntry 7 }
--
--PM line inithist 1D
--
adsl2PMLineInitHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24 hours intervals of ADSL2 line."
::= {adsl2PMLine 6}
adsl2PMLineInitHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24 hours intervals of ADSL2 line."
INDEX { adsl2PMLHistinit1DLineIfIndex, adsl2PMLHistinit1DInterval}
::= { adsl2PMLineInitHist1DayTable 1 }
Expires December 1, 2005 [Page 70]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Adsl2PMLineInitHist1DayEntry ::=
SEQUENCE {
adsl2PMLHistinit1DLineIfIndex Unsigned32,
adsl2PMLHistinit1DInterval Unsigned32,
adsl2PMLHistinit1DFullInits Unsigned32,
adsl2PMLHistinit1DFailedFullInits Unsigned32,
adsl2PMLHistinit1DShortInits Unsigned32,
adsl2PMLHistinit1DFailedShortInits Unsigned32,
adsl2PMLHistinit1DValidInterval Adsl2YesNo
}
adsl2PMLHistinit1DLineIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an ATUC
board in the system."
::= { adsl2PMLineInitHist1DayEntry 1 }
adsl2PMLHistinit1DInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist1DayEntry 2 }
adsl2PMLHistinit1DFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line (successful
and failed) during this interval."
::= { adsl2PMLineInitHist1DayEntry 3 }
adsl2PMLHistinit1DFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
::= { adsl2PMLineInitHist1DayEntry 4 }
adsl2PMLHistinit1DShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line (successful
and failed) during this interval."
Expires December 1, 2005 [Page 71]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
::= { adsl2PMLineInitHist1DayEntry 5 }
adsl2PMLHistinit1DFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
::= { adsl2PMLineInitHist1DayEntry 6 }
adsl2PMLHistinit1DValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information?"
::= { adsl2PMLineInitHist1DayEntry 7 }
--
--PM channel current counters
--
adsl2PMChCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChCurrTable contains current Performance
Monitoring results of ADSL2 channel."
::= {adsl2PMChannel 1}
adsl2PMChCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChCurrTable contains current Performance
Monitoring results of ADSL2 channel."
INDEX { adsl2PMChCurrChannelIfIndex, adsl2PMChCurrUnit }
::= { adsl2PMChCurrTable 1 }
Adsl2PMChCurrEntry ::=
SEQUENCE {
adsl2PMChCurrChannelIfIndex Unsigned32,
adsl2PMChCurrUnit Adsl2Unit,
adsl2PMChCurrValidIntervals Unsigned32,
adsl2PMChCurrInvalidIntervals Unsigned32,
adsl2PMChCurr15MtimeElapsed Unsigned32,
adsl2PMChCurr15McodingViolations Unsigned32,
adsl2PMChCurr15MCorrectedBlocks Unsigned32,
adsl2PMChCurr1DayValidIntervals Unsigned32,
adsl2PMChCurr1DayInvalidIntervals Unsigned32,
adsl2PMChCurr1DayTimeElapsed Unsigned32,
adsl2PMChCurr1DayCodingViolations Unsigned32,
adsl2PMChCurr1DayCorrectedBlocks Unsigned32
Expires December 1, 2005 [Page 72]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
}
adsl2PMChCurrChannelIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2PMChCurrEntry 1 }
adsl2PMChCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChCurrEntry 2 }
adsl2PMChCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 3 }
adsl2PMChCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 4 }
adsl2PMChCurr15MtimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { adsl2PMChCurrEntry 5 }
adsl2PMChCurr15McodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC?8 (FEBE for ATU-R) anomalies occurring in the channel
during the interval. This parameter is inhibited during UAS or
SES. If the CRC is applied over multiple channels, then each
related CRC?8 (or FEBE)anomaly should increment each of the
counters related to the individual channels."
::= { adsl2PMChCurrEntry 6 }
Expires December 1, 2005 [Page 73]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
adsl2PMChCurr15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter is
inhibited during UAS or SES. If the FEC is applied over multiple
channels, then each related FEC (or FFEC) anomaly should
increment each of the counters related to the individual
channels."
::= { adsl2PMChCurrEntry 7 }
adsl2PMChCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 8 }
adsl2PMChCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 9 }
adsl2PMChCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { adsl2PMChCurrEntry 10 }
adsl2PMChCurr1DayCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC?8 (FEBE for ATU-R) anomalies occurring in the channel
during the interval. This parameter is inhibited during UAS or
SES. If the CRC is applied over multiple channels, then each
related CRC?8 (or FEBE) anomaly should increment each of the
counters related to the individual channels."
::= { adsl2PMChCurrEntry 11 }
adsl2PMChCurr1DayCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
Expires December 1, 2005 [Page 74]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter is
inhibited during UAS or SES. If the FEC is applied over multiple
channels, then each related FEC (or FFEC) anomaly should
increment each of the counters related to the individual
channels."
::= { adsl2PMChCurrEntry 12 }
--
--PM channel hist 15M
--
adsl2PMChHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChCurrTable contains current Performance
Monitoring results of ADSL2 channel."
::= {adsl2PMChannel 2}
adsl2PMChHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChCurrTable contains current Performance
Monitoring results of ADSL2 channel."
INDEX { adsl2PMChHist15MChannelIfIndex, adsl2PMChHist15MUnit,
adsl2PMChHist15MInterval }
::= { adsl2PMChHist15MinTable 1 }
Adsl2PMChHist15MinEntry ::=
SEQUENCE {
adsl2PMChHist15MChannelIfIndex Unsigned32,
adsl2PMChHist15MUnit Adsl2Unit,
adsl2PMChHist15MInterval Unsigned32,
adsl2PMChHist15MMonitoredTime Unsigned32,
adsl2PMChHist15MCodingViolations Unsigned32,
adsl2PMChHist15MCorrectedBlocks Unsigned32,
adsl2PMChHist15MValidInterval Adsl2YesNo
}
adsl2PMChHist15MChannelIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an ATUC
board in the system."
::= { adsl2PMChHist15MinEntry 1 }
adsl2PMChHist15MUnit OBJECT-TYPE
Expires December 1, 2005 [Page 75]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist15MinEntry 2 }
adsl2PMChHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist15MinEntry 3 }
adsl2PMChHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist15MinEntry 4 }
adsl2PMChHist15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC?8 (FEBE for ATU-R) anomalies occurring in the channel
during the interval. This parameter is inhibited during UAS or
SES. If the CRC is applied over multiple channels, then each
related CRC?8 (or FEBE) anomaly should increment each of the
counters related to the individual channels."
::= { adsl2PMChHist15MinEntry 5 }
adsl2PMChHist15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter is
inhibited during UAS or SES. If the FEC is applied over multiple
channels, then each related FEC (or FFEC) anomaly should increment
each of the counters related to the individual channels."
::= { adsl2PMChHist15MinEntry 6 }
adsl2PMChHist15MValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information?"
::= { adsl2PMChHist15MinEntry 7 }
Expires December 1, 2005 [Page 76]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
--
--PM channel hist 1D
--
adsl2PMChHist1DTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChHist1DayTable contains PM channel history for
1 day intervals of ADSL2."
::= {adsl2PMChannel 3}
adsl2PMChHist1DEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2PMChHist1DayTable contains PM channel history for
1 day intervals of ADSL2."
INDEX { adsl2PMChHist1DChannelIfIndex, adsl2PMChHist1DUnit,
adsl2PMChHist1DInterval }
::= { adsl2PMChHist1DTable 1 }
Adsl2PMChHist1DEntry ::=
SEQUENCE {
adsl2PMChHist1DChannelIfIndex Unsigned32,
adsl2PMChHist1DUnit Adsl2Unit,
adsl2PMChHist1DInterval Unsigned32,
adsl2PMChHist1DMonitoredTime Unsigned32,
adsl2PMChHist1DCodingViolations Unsigned32,
adsl2PMChHist1DCorrectedBlocks Unsigned32,
adsl2PMChHist1DValidInterval Adsl2YesNo
}
adsl2PMChHist1DChannelIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex pattern that identifies a certain ADSL line on an
ATUC board in the system."
::= { adsl2PMChHist1DEntry 1 }
adsl2PMChHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist1DEntry 2 }
adsl2PMChHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32
Expires December 1, 2005 [Page 77]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist1DEntry 3 }
adsl2PMChHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist1DEntry 4 }
adsl2PMChHist1DCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC?8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited during
UAS or SES. If the CRC is applied over multiple channels, then
each related CRC?8 (or FEBE) anomaly should increment each of the
counters related to the individual channels."
::= { adsl2PMChHist1DEntry 5 }
adsl2PMChHist1DCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter is
inhibited during UAS or SES. If the FEC is applied over multiple
channels, then each related FEC (or FFEC) anomaly should increment
each of the counters related to the individual channels."
::= { adsl2PMChHist1DEntry 6 }
adsl2PMChHist1DValidInterval OBJECT-TYPE
SYNTAX Adsl2YesNo
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Does the interval contain valid information ?"
::= { adsl2PMChHist1DEntry 7 }
END
5. Acknowledgments
Expires December 1, 2005 [Page 78]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
6. Security Considerations
To be added
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features
as provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of a MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
7. IANA Considerations
The IANA is kindly requested to assign the value of the
MODULE-IDENTITY. The authors suggest transmission 227,
see section 4.
8. References
8.1. Normative References
8.2. Informative References
Authors' Addresses
Moti Morgenstern
ECI Telecom Ltd.
30 Hasivim St.
Petach Tikva 49517,
Israel.
Phone: +972 3 926 6258
Fax: +972 3 928 7342
Email: moti.Morgenstern@ecitele.com
Menachem Dodge
ECI Telecom Ltd.
30 Hasivim St.
Expires December 1, 2005 [Page 79]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
Petach Tikva 49517,
Israel.
Phone: +972 3 926 8421
Fax: +972 3 928 7342
Email: mbdodge@ieee.org
Full Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided
on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT
THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Expires December 1, 2005 [Page 80]
INTERNET-DRAFT NGADSL-LINE-MIB June 2005
