ANCP F. Le Faucheur
Internet-Draft Cisco
Intended status: Standards Track R. Maglione
Expires: September 9, 2010 Telecom Italia
T. Taylor
Huawei
March 8, 2010
Multicast Control Extensions for ANCP
draft-ietf-ancp-mc-extensions-02.txt
Abstract
This document specifies the extensions to the Access Node Control
Protocol required for support of the multicast use cases defined in
the Access Node Control Protocol framework document. Those use cases
are organized into the following ANCP capabilities:
o NAS-initiated multicast replication;
o conditional access with white and black lists;
o conditional access with grey lists;
o bandwidth delegation.
These capabilities may be combined according to the rules given in
this specification.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
Le Faucheur, et al. Expires September 9, 2010 [Page 1]
Internet-Draft ANCP Multicast Extensions March 2010
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on September 9, 2010.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Le Faucheur, et al. Expires September 9, 2010 [Page 2]
Internet-Draft ANCP Multicast Extensions March 2010
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Multicast Use Cases . . . . . . . . . . . . . . . . . . . . . 8
3.1. NAS Initiated Multicast Replication Control Use Case . . . 8
3.1.1. Goals . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1.2. Message Flow . . . . . . . . . . . . . . . . . . . . . 9
3.2. Conditional Access and Admission Control Use Case . . . . 9
3.2.1. Goals . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2.2. Message Flow . . . . . . . . . . . . . . . . . . . . . 10
3.3. Multicast Flow Reporting Use Case . . . . . . . . . . . . 11
3.3.1. Goals . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3.2. Message Flow . . . . . . . . . . . . . . . . . . . . . 11
4. ANCP Messages . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1. Provisioning Message . . . . . . . . . . . . . . . . . . . 13
4.1.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 13
4.1.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 14
4.2. Port Management Message . . . . . . . . . . . . . . . . . 15
4.2.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 15
4.2.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 16
4.3. Multicast Replication Control Message . . . . . . . . . . 16
4.3.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 21
4.3.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 21
4.4. Multicast Admission Control Message . . . . . . . . . . . 23
4.4.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 24
4.4.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 25
4.5. Bandwidth Reallocation Request Message . . . . . . . . . . 26
4.5.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 27
4.5.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 27
4.6. Bandwidth Transfer Message . . . . . . . . . . . . . . . . 29
4.6.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 30
4.6.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 30
4.7. Delegated Bandwidth Query Request Message . . . . . . . . 31
4.7.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 32
4.7.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 32
4.8. Delegated Bandwidth Query Response Message . . . . . . . . 32
4.8.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 32
4.8.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 33
4.9. Multicast Flow Query Request and Response Messages . . . . 33
4.9.1. Sender Behaviour . . . . . . . . . . . . . . . . . . . 34
4.9.2. Receiver Behaviour . . . . . . . . . . . . . . . . . . 35
5. ANCP TLVs For Multicast . . . . . . . . . . . . . . . . . . . 37
5.1. Multicast-Service-Profile TLV . . . . . . . . . . . . . . 37
5.2. Multicast-Service-Profile-Name TLV . . . . . . . . . . . . 38
5.3. List-Action TLV . . . . . . . . . . . . . . . . . . . . . 38
5.4. Sequence-Number TLV . . . . . . . . . . . . . . . . . . . 41
5.5. Bandwidth-Allocation TLV . . . . . . . . . . . . . . . . . 42
Le Faucheur, et al. Expires September 9, 2010 [Page 3]
Internet-Draft ANCP Multicast Extensions March 2010
5.6. White-List-CAC TLV . . . . . . . . . . . . . . . . . . . . 42
5.7. MRepCtl-CAC TLV . . . . . . . . . . . . . . . . . . . . . 43
5.8. Bandwidth-Request TLV . . . . . . . . . . . . . . . . . . 43
5.9. Request-Source-IP TLV . . . . . . . . . . . . . . . . . . 44
5.10. Request-Source-MAC TLV . . . . . . . . . . . . . . . . . . 44
5.11. Multicast-Flow TLV . . . . . . . . . . . . . . . . . . . . 45
6. Multicast Capabilities . . . . . . . . . . . . . . . . . . . . 47
6.1. Required Protocol Support . . . . . . . . . . . . . . . . 47
6.1.1. Protocol Requirements For NAS-initiated Replication . 47
6.1.2. Protocol Requirements For Conditional Access With
White and Black Lists . . . . . . . . . . . . . . . . 48
6.1.3. Protocol Requirements For Conditional Access With
Grey Lists . . . . . . . . . . . . . . . . . . . . . . 49
6.1.4. Protocol Requirements For Delegated Bandwidth . . . . 50
6.2. Capability-Specific Procedures for Providing Multicast
Service . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.2.1. Procedures For NAS-initiated Replication . . . . . . . 51
6.2.2. Procedures For Conditional Access With Black and
White Lists . . . . . . . . . . . . . . . . . . . . . 52
6.2.3. Procedures For Conditional Access With Grey Lists . . 54
6.2.4. Procedures For Delegated Bandwidth . . . . . . . . . . 55
6.3. Combinations of Multicast Capabilities . . . . . . . . . . 56
6.3.1. Combination of Conditional Access With White and
Black Lists and Conditional Access With Grey Lists . . 56
6.3.2. Combination of Conditional Access With Delegated
Bandwidth . . . . . . . . . . . . . . . . . . . . . . 57
6.3.3. Combination of NAS-Initiated Replication with
Other Capabilities . . . . . . . . . . . . . . . . . . 57
7. Security Considerations . . . . . . . . . . . . . . . . . . . 59
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 60
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 63
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 64
10.1. Normative References . . . . . . . . . . . . . . . . . . . 64
10.2. Informative References . . . . . . . . . . . . . . . . . . 64
Appendix A. Example of Messages and Message Flows . . . . . . . . 66
A.1. Provisioning Phase . . . . . . . . . . . . . . . . . . . . 66
A.2. Handling a Grey-Listed Flow . . . . . . . . . . . . . . . 72
A.3. Handling White-Listed Flows . . . . . . . . . . . . . . . 77
A.4. Handling Of Black-Listed Join Requests . . . . . . . . . . 82
A.5. Handling Of Requests To Join and Leave the On-Line Game . 82
A.6. Example Flow For Multicast Flow Reporting . . . . . . . . 85
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 89
Le Faucheur, et al. Expires September 9, 2010 [Page 4]
Internet-Draft ANCP Multicast Extensions March 2010
1. Introduction
[I-D.ietf-ancp-framework] defines a framework and requirements for an
Access Node control mechanism between a Network Access Server (NAS)
and an Access Node (e.g. a Digital Subscriber Line Access Multiplexer
(DSLAM)) in a multi-service reference architecture in order to
perform QoS-related, service-related and subscriber-related
operations. [I-D.ietf-ancp-protocol] specifies a protocol for Access
Node Control in broadband networks in line with this framework.
The Access Node Control Protocol (ANCP) specified in
[I-D.ietf-ancp-protocol] supports a number of use cases defined in
[I-D.ietf-ancp-framework] such as the Access Topology Discovery use
case, the Access Loop Configuration use case and the Remote
Connectivity Test use case. However, it does not support the
multicast use cases defined in [I-D.ietf-ancp-framework]. The
present document specifies the extensions to the Access Node Control
Protocol required for support of these multicast use cases. In terms
of the ANCP protocol, these use cases are organized into four
capabilities:
o NAS-initiated multicast replication;
o conditional access with white and black lists;
o conditional access with grey lists;
o bandwidth delegation.
NAS-initiated multicast replication assumes that multicast "join" and
"leave" requests are terminated on the NAS, or that the NAS receives
requests to establish multicast sessions through other means (e.g.,
application-level signalling). The NAS sends commands to the AN to
start or stop replication of specific multicast flows on specific
subscriber ports. This use case is described briefly in the next-to-
last paragraph of Section 3.4 of [I-D.ietf-ancp-framework].
Conditional access is described in Sections 3.4.1 and 3.4.2.3 of
[I-D.ietf-ancp-framework], with the latter section particularly
applicable to operation with white and black lists only. In case of
"conditional access with white and black lists", multicast join and
leave requests are terminated at the AN and accepted or ignored in
accordance with the direction provided by white and black lists
respectively. The white and black lists are provisioned per port at
startup time and may be modified thereafter. The NAS may enable
admission control of white-listed flows by appropriate provisioning.
Conditional access with grey lists is similar to conditional access
Le Faucheur, et al. Expires September 9, 2010 [Page 5]
Internet-Draft ANCP Multicast Extensions March 2010
with white lists, except that before accepting any request matching a
grey list entry, the AN sends a request to the NAS for permission to
replicate the flow. Again, the NAS can enable admission control of
grey-listed flows at the AN.
Bandwidth delegation is described in Section 3.4.2.1 of
[I-D.ietf-ancp-framework]. It allows flexible sharing of total video
bandwidth on an access line between the AN and the NAS. One
application of such bandwidth sharing is where the AN does multicast
admission control, while the NAS or Policy Server does unicast
admission control. In that case, bandwidth delegation allows dynamic
sharing of bandwidth between unicast and multicast video traffic on
each access line.
The formal specification of the behaviours associated with each of
these capabilities, singly and in combination, is given in Section 6.
In addition to the multicast service processing behaviour just
sketched, the definition of each capability includes support for the
multicast accounting and reporting services described in Section
3.4.3 of [I-D.ietf-ancp-framework]. Because of this common content
and because of other protocol overlaps between the different
capabilities, the protocol descriptions for the multicast extensions
specified in this document are merged into a single non-redundant
narrative. Tables in Section 6 then indicate the specific sub-
sections of the protocol description that have to be implemented to
support each capability.
Le Faucheur, et al. Expires September 9, 2010 [Page 6]
Internet-Draft ANCP Multicast Extensions March 2010
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
The expression "delegated bandwidth" is used as a shorter way of
saying: "the total amount of video bandwidth delegated to the AN for
multicast admission control".
Le Faucheur, et al. Expires September 9, 2010 [Page 7]
Internet-Draft ANCP Multicast Extensions March 2010
3. Multicast Use Cases
Quoting from [I-D.ietf-ancp-framework]:
"... the Access Node, aggregation node(s) and the NAS must all be
involved in the multicast replication process. This avoids that
several copies of the same stream are sent within the access/
aggregation network. In case of an Ethernet-based access/aggregation
network, this may, for example, be achieved by means of IGMP snooping
or IGMP proxy in the Access Node and aggregation node(s). By
introducing IGMP processing in the access/aggregation nodes, the
multicast replication process is now divided between the NAS, the
aggregation node(s) and Access Nodes. In order to ensure backward
compatibility with the ATM-based model, the NAS, aggregation node and
Access Node need to behave as a single logical device. This logical
device must have exactly the same functionality as the NAS in the ATM
access/aggregation network. The Access Node Control Mechanism can be
used to make sure that this logical/functional equivalence is
achieved by exchanging the necessary information between the Access
Node and the NAS. "
[I-D.ietf-ancp-framework] describes the use cases for ANCP associated
with such multicast operations, and identifies the associated ANCP
requirements. The present section describes a subset of these use
cases as background to facilitate reading of this document, but the
reader is refered to [I-D.ietf-ancp-framework] for a more exhaustive
description of the ANCP multicast use cases. Detailed example
message flows can also be found in Appendix A.
3.1. NAS Initiated Multicast Replication Control Use Case
3.1.1. Goals
One option for multicast handling is for the subscriber to
communicate the "join/leave" information to the NAS. This can be
done for instance by terminating all subscriber IGMP ([RFC3376]) or
MLD ([RFC2710], [RFC3810]) signaling on the NAS. Another example
could be a subscriber using some form of application level signaling,
which is redirected to the NAS. In any case, this option is
transparent to the access and aggregation network. In this scenario,
the NAS uses ANCP to create and remove replication state in the AN
for efficient multicast replication. Thus, the NAS only sends a
single copy of the multicast stream towards the AN, which in turn
performs replication to multiple subscribers as instructed by the NAS
via ANCP. The NAS first performs conditional access and multicast
admission control when processing multicast join requests, and only
creates replication state in the AN if admission succeeds.
Le Faucheur, et al. Expires September 9, 2010 [Page 8]
Internet-Draft ANCP Multicast Extensions March 2010
3.1.2. Message Flow
With the NAS-initiated use case, a Multicast Replication Control
Message is sent by the NAS to the AN with a directive to either join
or leave one (or more) multicast flow(s). In the example message
flow, the AN uses a Generic Response message to convey the outcome of
the directive. Figure 1 illustrates such an ANCP message exchange as
well as the associated AN behavior.
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<-------------------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | (*)
| | | Multicast-Replication-Crl |
| | | (Target,add, Flow 1) |
| | |<--------------------------|
| Mcast Flow 1 | |
|<==========================+ |
| | | Generic Response |
| | |-------------------------->|
| | | |
| | | |
~ ~ ~ ~
| | | |
| | | Multicast-Replication-Crl |
| | | (Target,delete, Flow 1) |
| | |<--------------------------|
| | | |
| <Stop Replication of X |
| Mcast Flow 1> | Generic Response |
| | |-------------------------->|
(*) The NAS may optionally seek direction from an external
Authorization/Policy Server before admitting the flow.
Figure 1: NAS Initiated Multicast Replication Control
3.2. Conditional Access and Admission Control Use Case
3.2.1. Goals
One option for multicast handling is for the access/aggregation nodes
to participate in IGMP/MLD processing (e.g. via IGMP/MLD snooping).
In this scenario, on detecting a join/leave request from an enduser
for a multicast flow (in the grey list), the AN uses ANCP to request
conditional access and admission control decision from the NAS. In
turn, after conditional access and admission control checks, the NAS
Le Faucheur, et al. Expires September 9, 2010 [Page 9]
Internet-Draft ANCP Multicast Extensions March 2010
uses ANCP to instruct the AN to change the replication states
accordingly.
3.2.2. Message Flow
For support of the conditional access and admission control use case,
on detection of an IGMP/MLD Join, the AN sends an Admission Control
message to the NAS to request conditional access and admission
control check. In case of positive outcome, the NAS sends a
Multicast Replication Control Message to the AN with a directive to
replicate the multicast flow to the corresponding user. Similarly on
detection of an IGMP/MLD leave, an Admission Control message is sent
by the AN to the NAS to keep the NAS aware of user departure for the
flow. This message flow is illustrated in Figure 2.
Le Faucheur, et al. Expires September 9, 2010 [Page 10]
Internet-Draft ANCP Multicast Extensions March 2010
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<------------------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | |
| Join(Gr-Flow1) | Admission-Control |
|------------+---------->| (Target,add,Gr-Flow1) |
| | |-------------------------->|
| | | (*)
| | | Multicast-Replication-Crl |
| | | (Target,add,Gr-Flow 1) |
| | |<--------------------------|
| Mcast Gr-Flow1 | |
|<=======================+ |
| | | |
~ ~ ~ ~
| | | |
| Leave(Gr-Flow1) | Admission-Control |
|------------+---------->| (Target,delete,Gr-Flow1) |
| | |-------------------------->|
| <Stop Replication of X |
| Mcast Gr-Flow1> | |
| | | |
Gr-Flow1: a multicast flow matching the grey list for that port
(*) The NAS may optionally seek direction from an external
Authorization/Policy Server before admitting the flow.
Figure 2: Multicast Conditional Access and Admission Control
3.3. Multicast Flow Reporting Use Case
3.3.1. Goals
The Multicast flow reporting use case allows the NAS to
asynchronously query the AN to obtain an instantaneous status report
related to multicast flows currently replicated by the AN.
3.3.2. Message Flow
The NAS sends a Multicast Flow Query Request message to the AN in
order to query the AN about information such as which multicast flows
are currently active on a given AN port or which ports are currently
replicating a given multicast flow. The AN conveys the requested
information to the NAS in a Multicast Flow Query Response message.
This message flow is illustrated in Figure 3.
Le Faucheur, et al. Expires September 9, 2010 [Page 11]
Internet-Draft ANCP Multicast Extensions March 2010
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<---------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | Multicast Flow |
| | | Query Request |
| | |<------------------|
| | | |
| | | Multicast Flow |
| | | Query Response |
| | |------------------>|
| | | |
| | | |
Figure 3: Multicast Flow Reporting
Le Faucheur, et al. Expires September 9, 2010 [Page 12]
Internet-Draft ANCP Multicast Extensions March 2010
4. ANCP Messages
This section defines new ANCP messages and new usage of existing ANCP
messages as well as procedures associated with the use of these
messages.
4.1. Provisioning Message
Section 5.4.3.1 of [I-D.ietf-ancp-protocol] defines the Provisioning
message that is sent by the NAS to the AN to provision information in
the AN.
The present document specifies that the Provisioning message MAY be
used by the NAS to provision multicast-related information (e.g.
multicast service profiles). The ANCP Provisioning message payload
MAY contain:
o one or more instances of the Multicast-Service-Profile TLV. The
Multicast-Service-Profile TLV is defined in the present document
in Section 5.1. Each instance of the Multicast-Service-Profile
TLV contains a multicast service profile name and one or more list
actions. A list action consists of an action (add, delete,
replace), a list type (White, Black, or Grey), and list content
(multicast source and group addresses).
o an instance of the White-List-CAC TLV. The White-List-CAC TLV is
defined in Section 5.6. If present, this TLV indicates that the
AN is required to do admission control before replicating White-
listed flows.
o an instance of the MRepCtl-CAC TLV. The MRepCtl-CAC TLV is
defined in Section 5.7. If present, this TLV indicates that the
AN is required to do admission control before replicating flows
specified in Multicast Replication Control messages.
See Section 6 for information on which multicast capabilities require
support of these TLVs in the Provisioning message.
4.1.1. Sender Behaviour
When directed by the Policy Server or by management action, the NAS
sends the Provisioning message to initially provision or to update
the White, Black, and/or Grey multicast channel lists associated with
a set of named multicast service profiles, or to enable the AN to
perform admission control for specific classes of flows.
To provision or update a multicast service profile, the NAS MUST
include within the message one or more instances of the Multicast-
Le Faucheur, et al. Expires September 9, 2010 [Page 13]
Internet-Draft ANCP Multicast Extensions March 2010
Service-Profile TLV specifying the content to be provisioned or
updated. The NAS SHOULD NOT include any list type (White, Black, or
Grey) that is not supported by the set of multicast capabilities
negotiated between the NAS and the AN. The NAS MUST NOT use the
Provisioning message to send instances of the Multicast-Service-
Profile TLV to the AN unless the Multicast-Service-Profile TLV is
supported by the set of multicast capabilities negotiated between the
NAS and the AN.
To require admission control to be performed at the AN on White-
listed flows, the NAS MUST include a copy of the White-List-CAC TLV
in the Provisioning message. The White-List-CAC TLV MUST NOT be
provided unless the negotiated set of capabilities includes
conditional access with White and Black lists.
To require admission control to be performed at the AN on Grey-listed
flows or on NAS-initiated flows, the NAS MUST include a copy of the
MRepCtl-CAC TLV in the Provisioning message. The MRepCtl-CAC TLV
MUST NOT be provided unless the negotiated set of capabilities
includes NAS-initiated replication control or conditional access with
Grey lists.
4.1.2. Receiver Behaviour
The receiving AN provisions/updates the White, Black, and/or Grey
lists associated with the multicast service profile names contained
in the Multicast-Service-Profile TLV instances within the message
according to the contents of the associated List-Action TLVs. The AN
MUST process List-Action TLVs in the order in which they appear
within the message. The AN MUST ignore instances of the List-Action
TLV referring to any list type (White, Black, or Grey) that is not
supported by the set of multicast capabilities negotiated between the
NAS and the AN.
When a new multicast service profile is identified by a Multicast-
Service-Profile TLV, the initial state of all lists associated with
that profile according to the negotiated set of multicast
capabilities is empty until changed by the contents of Multicast-
Service-Profile TLVs.
The receipt of a Provisioning message containing updates to an
existing multicast service profile subsequent to startup will cause
the AN to review the status of active flows on all ports to which
that profile has been assigned. For further details, see Section 6.
If the White-List-CAC and/or MRepCtl-CAC TLV is present in the
Provisioning message and the respective associated capabilities have
been negotiated, the AN prepares (or continues) to do connection
Le Faucheur, et al. Expires September 9, 2010 [Page 14]
Internet-Draft ANCP Multicast Extensions March 2010
admission control on the indicated class(es) of flow. If one or both
of these TLVs was present in an earlier Provisioning message but is
absent in the latest message received, the AN ceases to do connection
admission control on the indicated class(es) of flow.
As indicated in [I-D.ietf-ancp-protocol], the AN MUST NOT reply to
the Provisioning message if it processed it successfully. If an
error prevents successful processing of the message content, the AN
MUST return a Generic Response message as defined in
[I-D.ietf-ancp-protocol], containing a Status-Info TLV with the
appropriate content describing the error. For this purpose, the
presence of a list type in a Multicast-Service-Profile TLV which was
ignored because it was not supported by the negotiated set of
capabilities is not considered to be an error.
Editor's note: that means that if a NAS mistakenly adds the wrong
list types there will be no debugging feedback. On the other
hand, this adds flexibility for handling pre-assembled sets of
list updates being sent out to multiple ANs. If there are no
comments on this feature/bug, this Editor's note will be removed
in the next version of the draft.
4.2. Port Management Message
As specified in [I-D.ietf-ancp-protocol], the NAS may send line
configuration information to the AN ("ANCP based Line Configuration"
use case) using GSMP Port Management messages modified to contain an
extension block. Section 5.4.3 of [I-D.ietf-ancp-protocol] defines a
number of TLVs that can be included in the Extension Value field
inside a Port Management message to support line configuration.
This document specifies that the Port Management message MAY also
include either or both of the following TLVs:
o Multicast-Service-Profile-Name TLV (defined in Section 5.2). This
TLV associates a Multicast Service Profile with the Access Port
specified by the extension block.
o Bandwidth-Allocation TLV (defined in Section 5.5). This TLV
specifies the total multicast bandwidth available to the AN for
admission control at the Access Port.
4.2.1. Sender Behaviour
The NAS sends the Port Management message at startup time to
initialize parameters associated with the Access Port specified in
the message and with the multicast capabilities negotiated between
the NAS and the AN. The NAS MAY send additional Port Management
Le Faucheur, et al. Expires September 9, 2010 [Page 15]
Internet-Draft ANCP Multicast Extensions March 2010
messages subsequent to startup, to update or, in the case of the
Bandwidth-Allocation TLV, reset these parameters. If the NAS
includes a Multicast-Service-Profile-Name TLV in the Port Management
message, the name MUST match a profile name provided in a Multicast-
Service-Profile TLV in a prior Provisioning message. The NAS MUST
NOT include a TLV unless it is supported by the set of multicast
capabilities negotiated between the NAS and the AN. See Section 6
for further information.
4.2.2. Receiver Behaviour
If the Port Management message contains a Multicast-Service-Profile-
Name TLV, the AN associates the named profile with the specified
Access Port. This association replaces any previous association.
That is, a given Access Port is associated with at most one multicast
service profile. The replacement of one multicast service profile
with another will cause the AN to review the status of all active
flows on the target port. For further details see Section 6.
If the Port Management message contains a Bandwidth-Allocation TLV,
the AN adopts this as the current value of its total multicast
bandwidth limit for the target port. If the AN has already committed
multicast bandwidth exceeding the amount given in the Bandwidth-
Allocation TLV, the AN SHOULD NOT discontinue any multicast streams
in order to bring bandwidth down to within the new limit. However,
the AN MUST NOT admit new multicast streams that are subject to
admission control until it can do so within the limit specified by
the Bandwidth-Allocation TLV.
If the Port Management request cannot be processed due to error and
the Result field of the request is Nack (0x1) or AckAll (0x2), the AN
SHOULD add a Status-Info TLV to the Extension Value field in its
reply if this will provide useful information beyond what is provided
by the Code value returned in the response header. In particular, if
the name within the Multicast-Service-Profile-Name TLV does not match
a profile name given in a prior Provisioning message, the AN SHOULD
return a reply where the Code field in the header indicates "Invalid
TLV value" (85), the Error Message field in the Status-Info TLV
contains the text "Multicast profile name not provisioned", and the
Status-Info TLV contains a copy of the Multicast-Service-Profile-Name
TLV.
4.3. Multicast Replication Control Message
This section defines a new message called the Multicast Replication
Control message. The Multicast Replication Control message is sent
by the NAS to the AN with one or more directives to add (join) or
delete (leave) a multicast flow on a target object identified in the
Le Faucheur, et al. Expires September 9, 2010 [Page 16]
Internet-Draft ANCP Multicast Extensions March 2010
content of the message.
The Message Type for the Multicast Replication Control message is
144.
The ANCP Multicast Replication Control message payload contains the
following TLVs:
o Target TLV: The Target TLV is defined in [I-D.ietf-ancp-protocol].
It MUST appear once and only once. It is encoded as specified in
[I-D.ietf-ancp-protocol] and identifies the AN port subject to the
request for admission or release.
o Command TLV: The Command TLV is defined in
[I-D.ietf-ancp-protocol]. It MUST be present. It MAY appear
multiple times.
As [I-D.ietf-ancp-protocol] indicates, the contents of the Command
Info field within the Command TLV are specific to the message in
which the TLV occurs. For the Multicast Replication Control Message,
these contents consist of:
o a Command Code field;
o an Accounting field;
o an instance of the Multicast-Flow TLV.
Figure 4 illustrates the complete Command TLV with the contents
specific to the Multicast Replication Control message.
Le Faucheur, et al. Expires September 9, 2010 [Page 17]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = Command | Command-TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Command Code | Accounting | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast-Flow TLV |
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Other embedded TLV Type | Other embedded TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Other embedded TLV data ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Contents of the Command TLV in the Multicast Replication
Control Message
Command Code:
Command directive:
0x01 - Add;
0x02 - Delete;
0x03 - Delete All;
0x04 - Admission Control Reject;
0x05 - Conditional Access Reject;
0x06 - Admission Control and Conditional Access
Reject.
Directives 0x04 through 0x06 are used as described in
Section 4.4.2
Accounting:
Meaningful only when the Command Code is "Add" (0x01). In
that case, 0x00 indicates no flow accounting, 0x01
indicates that octet accounting for the flow is to
commence. The Accounting field MUST be set to 0x00 for
other Command Code values.
Le Faucheur, et al. Expires September 9, 2010 [Page 18]
Internet-Draft ANCP Multicast Extensions March 2010
Reserved:
Reserved for future use. MUST be set to 0x0000 by the
sender and ignored by the receiver.
Multicast-Flow TLV:
An instance of the Multicast-Flow TLV (Section 5.11)
specifying the flow to be added or deleted. The Multicast-
Flow TLV MUST be omitted if the Command Code has value
"Delete All" (0x03).
Other embedded TLV:
No other embedded TLVs are currently specified within the
Multicast Replication Control message/Command TLV.
Unrecognized embedded TLVs SHOULD be silently discarded.
The figure below is an example of a Multicast Replication Control
message that would result in a swap from multicast SSM flows
192.0.2.1, 233.252.0.2, to 192.0.2.2, 233.252.0.3 on the Target
identified by the "Access Loop Circuit ID":
Le Faucheur, et al. Expires September 9, 2010 [Page 19]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub |MessageType=144| 0x02 | Code |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier = 0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = Target 0x1000 | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = Command TLV | Command-TLV Length = 0x0014 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x02 |Acctg = 0x00 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Multicast-Flow | TLV Length = 0x000C |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |AddrFam = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address: 233.252.0.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
| Source Address = 192.0.2.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
| Type = Command-TLV | Command-TLV Length = 0x0014 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x01 |Acctg = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Multicast-Flow | TLV Length = 0x000C |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |AddrFam = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.0.3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Address = 192.0.2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
Le Faucheur, et al. Expires September 9, 2010 [Page 20]
Internet-Draft ANCP Multicast Extensions March 2010
4.3.1. Sender Behaviour
The NAS MAY issue a Multicast Replication Control message to the AN
to convey one or more directives to add (join) or delete (leave) one
or more multicast flows.
The NAS MAY send this message on its own initiative to support the
NAS initiated Multicast Control use case presented in
[I-D.ietf-ancp-framework] and summarized in Section 3.1. In that
case, the NAS MUST set the Result field to AckAll (0x2) or Nack (0x1)
according to its requirements.
The NAS MAY also send this message in response to a Multicast
Admission Control message (defined in Section 4.4) received from the
AN to support the conditional access and admission control use case
presented in [I-D.ietf-ancp-framework] and summarized in Section 3.2.
In that case, the NAS MUST set the Result field to NAck (0x1).
In either case, the sender MUST populate the Code field with the
value 0x000 and the ANCP Transaction Identifier field with a unique
value, as described in section 5.4.5 of [I-D.ietf-ancp-protocol].
Each Multicast Replication Control Message MUST contain one or more
commands, each encapsulated in its own Command TLV. The sender MUST
use a separate Command TLV for each distinct multicast flow.
When the order of processing of two commands does not matter, the
commands MUST be transmitted in separate Multicast Replication
Control messages.
4.3.2. Receiver Behaviour
When successive commands (in the same or different messages) relate
to the same Target and multicast flow, the state of each feature
controlled or affected by attributes received in the Multicast
Replication Control message, SHALL be as set by the last command or
message referring to that target and flow and containing the
controlling attribute. As an example, successive Multicast
Replication Control messages containing add commands for a given port
and flow, but differing only in the Accounting field setting SHALL be
interpreted to mean that the state of the accounting feature is as
set in the final command received, but all other features are as set
in the initial message.
If more than one Command TLV is present in a Multicast Replication
Control message, the AN MUST act on the commands in the order in
which they are presented in the message. The AN SHALL assign a
sequence number to each command in a given Multicast Replication
Le Faucheur, et al. Expires September 9, 2010 [Page 21]
Internet-Draft ANCP Multicast Extensions March 2010
Control message, starting from 0x01 for the first command.
If a Command TLV adds a flow and the AN is performing admission
control for Multicast Replication Control messages, then the AN MUST
perform admission control before replicating the flow. If the
admission control check fails, the AN MUST treat the failure as an
error as described below. The appropriate Code value for the
response is 18 (0x012) "Insufficient resources".
If the AN processes the complete Multicast Replication Control
message successfully and the Result field of the Multicast
Replication Control message was set to AckAll (0x2), the AN MUST
respond with a Generic Response message where the Result field is set
to Success (0x3), the Code field is set to 0x000, and the Transaction
Identifier field is copied from the Multicast Replication Control
message. The body of the response MAY be empty or MAY be copied from
the Multicast Replication Control message.
If the AN processes the complete Multicast Replication Control
message successfully and the Result field of the Multicast
Replication Control message was set to Nack (0x1), the AN MUST NOT
respond to the message.
The processing/execution of multiple commands contained in a single
Multicast Control message MUST be interrupted at the first error
encountered, and the remaining commands in the Multicast Replication
Control message discarded.
If the AN detects an error in a received Multicast Replication
Control message and the Result field in that message was set to Nack
(0x1) or AckAll(0x2), the AN MUST generate a Generic Response message
providing error information to the NAS. This specification
identifies the following new Code values beyond those specified in
[I-D.ietf-ancp-protocol], which MAY be used in a Generic Response
sent in reply to a Multicast Replication Control message:
100 Command error. This SHOULD be reported for the case that an
invalid command code has been received.
101 Bad flow address. This SHOULD be reported for the following
cases:
* unsupported address family;
* source address present for an ASM flow, or absent for an SSM
flow.
Le Faucheur, et al. Expires September 9, 2010 [Page 22]
Internet-Draft ANCP Multicast Extensions March 2010
102 Multicast flow does not exist. This SHOULD be reported if the
NAS attempts to delete a flow that is not enabled.
A Generic Response message responding to the Multicast Replication
Control message and containing one of the above Code values MUST
include a Status-Info TLV which includes one or two embedded TLVs as
follows:
o a Sequence-Number TLV as described in Section 5.4, giving the
sequence number of the failed command, MUST be included;
o the failed Command TLV itself SHOULD be included.
Note that the Error Message field of the Status-Info TLV MAY be
used to report more details than implied by the Code value in the
message header. For example, the Code value could be 101 and the
Error Message field could contain the text: "Source address
present for ASM flow".
4.4. Multicast Admission Control Message
This section defines a new message called the Multicast Admission
Control message. The Multicast Admission Control message is sent by
the AN to the NAS to request admission of a multicast flow, or to
notify of the removal of a multicast flow, for a given target.
The Message Type for the Multicast Admission Control message is 145.
The ANCP Multicast Admission Control message payload contains two
TLVs:
o Target TLV: The Target TLV is defined in [I-D.ietf-ancp-protocol].
It MUST appear once and only once in the Multicast Admission
Control message. It is encoded as specified in
[I-D.ietf-ancp-protocol] and identifies the AN port subject to the
request for admission or release.
o Command TLV: The Command TLV is defined in
[I-D.ietf-ancp-protocol]. It MUST be present. If it appears more
than once, only the first instance is considered meaningful in the
present version of this specification and the other instances are
ignored.
Informative note:
In the future, the specification of the Admission Control message
may be extended to allow transport of more than a single directive
(e.g. to carry both a leave from one group and a join to another
Le Faucheur, et al. Expires September 9, 2010 [Page 23]
Internet-Draft ANCP Multicast Extensions March 2010
group for the same Target). It is expected that this would
support a similar notion of strict sequenced processing as
currently defined for handling multiple directives in the
Multicast Replication Control message whereby all directives
following the first directive that can not be executed are not
executed either. When the strict sequenced processing of the
directives is not required the directives are distributed across
separate messages.
The Command TLV has the same contents as were described above for the
Multicast Replication Control message, with the following additions:
o a Request-Source-IP TLV MAY be appended to the Command TLV as an
additional embedded TLV;
o similarly, a Request-Source-MAC TLV MAY be appended to the Command
TLV as an additional embedded TLV.
Note that the Command TLV length includes the length of any embedded
TLVs, including the embedded TLV headers.
4.4.1. Sender Behaviour
The AN sending the Multicast Admission Control message MUST set the
Result field to Ignore (0x0).
The AN MUST populate the ANCP Transaction Identifier field with a
unique value, as described in section 5.4.5
of[I-D.ietf-ancp-protocol] .
The AN MUST encode the Command TLV as specified in Section 4.3 with
the following additional rules:
o the Accounting field MUST be set to 0;
o the Command Code field MUST be set to "0x01 - Add" when the
message conveys a Join , to "0x02 - Delete" when the message
conveys a Leave and to "0x03 - Delete All" when the message
conveys a Leave of all channels (on the target);
o The Multicast-Flow TLV within the Command TLV identifies the
multicast flow subject to the request for admission or release.
When the Command Code is 0x03, the Multicast-Flow TLV is
meaningless and MUST be omitted.
o the Request-Source-IP embedded TLV MAY be included by the AN to
convey the IP address of the sender of the join/leave message
(e.g. IGMP/MLD Join/Leave) that triggered the AN to include the
Le Faucheur, et al. Expires September 9, 2010 [Page 24]
Internet-Draft ANCP Multicast Extensions March 2010
corresponding Command TLV in the Admission Control message. If it
appears more than once, only the first instance is considered
meaningful and the other instances are ignored.
o the Request-Source-MAC embedded TLV MAY be included by the AN to
convey the MAC address of the sender of the join/leave message
(e.g. IGMP/MLD Join/Leave) that triggered the AN to include the
corresponding Command TLV in the Admission Control message. If it
appears more than once, only the first instance is considered
meaningful and the other instances are ignored.
4.4.2. Receiver Behaviour
On receipt of an Multicast Admission Control message, the NAS:
o MUST ignore the Result field;
o if the directive in the Multicast Admission Control message is
"0x02 - Delete" or "0x03 - Delete All" and is processed correctly
by the NAS, the NAS MUST NOT generate any ANCP message in response
to the Multicast Admission Control message;
o if the directive in the Multicast Admission Control message is
"0x01 - Add" and is accepted by the NAS, the NAS MUST generate a
Multicast Replication Control in response to the Multicast
Admission Control message. The Multicast Replication Control
message:
* MUST contain a Result set to Nack (0x1);
* MUST contain a Transaction ID generated by the NAS (distinct
non-zero, and linearly incremented by NAS for each request per
adjacency);
* MUST contain the directive as accepted by the NAS. The NAS MAY
modify the Accounting field if flow accounting is required.
o if the directive in the Multicast Admission Control message is
"0x01 - Add", is processed correctly but not accepted by the NAS
(i.e. it does not pass the admission control or conditional access
check), the NAS MAY generate a Multicast Replication Control
message in response to the Multicast Admission Control message.
This optional message can be used by the AN to maintain statistics
about admission control rejections.
In the future, the AN may be able to notify the subscriber that
the request was rejected (e.g. using
[I-D.morin-mboned-igmpmld-error-feedback]).
Le Faucheur, et al. Expires September 9, 2010 [Page 25]
Internet-Draft ANCP Multicast Extensions March 2010
When used in this situation, the Multicast Replication Control
message:
* MUST contain a Result set to 0x0;
* MUST contain a Transaction ID generated by the NAS (distinct
non-zero, and linearly incremented by NAS for each request per
adjacency);
* MUST contain the directive rejected by the NAS (i.e. Target
TLV and Command TLV) but with a Command Code set to "0x04 -
Admission Control Reject", "0x05 - Conditional Access Reject",
or "0x06 - Admission Control and Conditional Access Reject".
o if the Multicast Admission Control message cannot be processed
correctly by the NAS (e.g. the message is malformed, the multicast
flow does not exist etc.), the NAS MUST generate a Generic
Response message (defined in [I-D.ietf-ancp-protocol]) with
appropriate content indicating the reason for the failure.
4.5. Bandwidth Reallocation Request Message
The Bandwidth Reallocation Request message is used when the bandwidth
delegation capability is included in the negotiated set. It MAY be
sent either by the NAS or by the AN to request an adjustment in the
amount of delegated bandwidth. It will be sent by the NAS typically
to reduce the multicast bandwidth allocated to the AN in order for
the NAS to satisfy a request to add one or more flows. Conversely,
the AN will send a Bandwidth Reallocation Request to obtain
additional bandwidth to satisfy a request to add a multicast channel.
In each case, the requestor has a minimum requirement for additional
bandwidth, and MAY ask for additional bandwidth beyond this amount
(e.g., to handle anticipated future requests).
The Bandwidth Reallocation Request message contains two TLVs:
o the Target TLV (section 5.4.5.1.1 of [I-D.ietf-ancp-protocol]),
specifying a single access line;
o the Bandwidth-Request TLV (Section 5.8), specifying the required
and preferred amounts of delegated bandwidth.
The Message Type for the Bandwidth Reallocation Request message is
146.
Le Faucheur, et al. Expires September 9, 2010 [Page 26]
Internet-Draft ANCP Multicast Extensions March 2010
4.5.1. Sender Behaviour
The Result field in the header of the Bandwidth Reallocation Request
message is not used and the sender MUST set it to Ignore (0x0).
The bandwidth values in the Bandwidth-Request TLV are expressed in
terms of total multicast bandwidth allocated to the AN.
The choice of "total bandwidth" rather than "incremental
bandwidth" was made so that it would be easier for the AN and NAS
to keep their respective views of the current amount of delegated
bandwidth synchronized.
Because the values are totals rather than desired increments/
decrements, the relationship between the required amount and the
preferred amount will differ depending on whether the Bandwidth
Reallocation Request message is issued by the NAS or the AN.
o If the NAS is making the request, the preferred amount MUST be
less than or equal to the required amount. The required amount
MUST be less than the currently amount of delegated bandwidth.
o If the AN is making the request, the preferred amount MUST be
greater than or equal to the required amount. The required amount
MUST be greater than the currently amount of delegated bandwidth.
4.5.2. Receiver Behaviour
When the peer receives a valid Bandwidth Reallocation Request
message, it SHOULD determine whether it can satisfy the request from
its existing allocation of unused video bandwidth. If it decides
that it can reallocate bandwidth to the peer, it MAY choose to return
any amount between the required and the preferred amounts indicated
in the Bandwidth Reallocation Request message.
The peer MUST return a Bandwidth Transfer message Section 4.6
indicating its decision. If the request is met, the Result field of
the Bandwidth Transfer message MUST be set to Success (0x3), the Code
field MUST be set to 0x000, and the Bandwidth-Allocation TLV
(Section 5.5) MUST contain the new value of total multicast
bandwidth. This new value MUST lie between the required and
preferred values, inclusive, from the request message. If the
request is not met, the Result field of the Bandwidth Transfer
message MUST be set to Failure (0x4), the Code field MUST be set to
0x000, and the Bandwidth Allocation TLV MUST contain the value of the
currently allocated amount of delegated bandwidth as the responder
views it.
Le Faucheur, et al. Expires September 9, 2010 [Page 27]
Internet-Draft ANCP Multicast Extensions March 2010
The following cases indicate that the sender holds a different view
of the amount of delegated bandwidth from the receiver:
o the NAS receives a request where the required amount is less than
its view of the current amount of delegated bandwidth;
o the AN receives a request where the required amount is greater
than its view of the current amount of delegated bandwidth.
If one of these cases occurs, the receiver with one exception MUST
send a Bandwidth Transfer message indicating Success.
o If the NAS received the request, the allocated amount in the NAS's
response MUST be at least equal to NAS's view of the current
amount of delegated bandwidth.
o If the AN received the request, the allocated amount in the AN's
response MUST be no greater than the AN's view of the current
amount of delegated bandwidth.
The exception is when the NAS receives a request while it has a
request of its own outstanding. Handling of that case is described
below.
While the cases just described are an error condition, the success
response achieves a graceful recovery.
To avoid deadlock due to race conditions, the following rules MUST be
applied:
a. If the NAS receives a Bandwidth Reallocation Request message
while it has a Bandwidth Reallocation Request message of its own
outstanding for the same access line, the NAS MUST provide an
immediate failure response to the request from the AN, with a
Code value set to 105 "Bandwidth request conflict".
b. If the AN receives a Bandwidth Reallocation Request message while
it has a Bandwidth Reallocation Request message of its own
outstanding for the same access line, the AN MUST release any
bandwidth it has already committed to an outstanding Join request
while it is awaiting a response from the NAS. It MUST decide
upon and send its response to the NAS taking the released
bandwidth into account.
If the receiver is unable to process the Bandwidth Reallocation
Request message due to an error, then the receiver MUST return a
Bandwidth Transfer message where:
Le Faucheur, et al. Expires September 9, 2010 [Page 28]
Internet-Draft ANCP Multicast Extensions March 2010
o the Result field is set to Failure (0x4),
o the Code field is set appropriately to indicate the type of error
that was detected,
o the Bandwidth Allocation TLV contains the value of the current
amount of delegated bandwidth as the responder views it, and
o a Status-Info TLV MAY follow the Bandwidth Allocation TLV giving
further information about the error.
This specification provides three new Code values applicable
specifically to the contents of the Bandwidth-Request TLV. These
Code values by their nature MUST only be used when the error is being
reported in a Bandwidth Transfer message rather than a Generic
Response message.
103 invalid preferred bandwidth amount. This indicates that the
preferred and required amounts of bandwidth in the TLV do not have
the numerical relationship described in the previous section.
104 inconsistent views of delegated bandwidth amount. This will
appear only in a Bandwidth Transfer message from the NAS to the AN
in the case where the NAS has an outstanding Bandwidth
Reallocation Request. The recommended procedure for recovery is
described in Section 4.6.2.
105 bandwidth request conflict. The NAS has rejected the AN's
request for more bandwidth because the NAS has an outstanding
bandwidth request.
4.6. Bandwidth Transfer Message
The Bandwidth Transfer message is used to transfer video bandwidth
from the sender to the peer for a specific access line. This message
MAY be sent either from the AN or from the NAS. As described in the
previous section, it is the required response to a valid Bandwidth
Reallocation Request message.
The Bandwidth Transfer message MAY also be used to transfer bandwidth
autonomously from one peer to another. One example of this usage is
to release bandwidth borrowed earlier by means of the Bandwidth
Reallocation Request message. When the message is used in this way,
the Result field in the Bandwidth Transfer message MUST be set to
Ignore (0x0).
This allows the receiver to distinguish between an autonomous
transfer and a response to a previous Bandwidth Reallocation
Le Faucheur, et al. Expires September 9, 2010 [Page 29]
Internet-Draft ANCP Multicast Extensions March 2010
Request, for purposes of validation.
The Message Type for the Bandwidth Transfer message is 147. The
Bandwidth Transfer message contains the following TLVs:
o the Target TLV, designating the access line concerned;
o an instance of the Bandwidth-Allocation TLV (Section 5.5). The
bandwidth value in the Bandwidth-Allocation TLV is the new amount
of delegated bandwidth allocated to the target.
4.6.1. Sender Behaviour
When sending a Bandwidth Transfer message where the Result value is
Ignore (0x0) or Success (0x3), the following relationships MUST hold:
o if the message is sent by the NAS, the bandwidth value in the
Bandwidth-Allocation TLV MUST be greater than or equal to the
sender's view of the current amount of delegated bandwidth for the
access line concerned;
o if the message is sent by the AN, the bandwidth value in the
Bandwidth-Allocation TLV MUST be less than or equal to the
sender's view of the current amount of delegated bandwidth for the
access line concerned.
Further sender behaviour is specified above, in Section 4.5.2.
4.6.2. Receiver Behaviour
4.6.2.1. Behaviour of the NAS
If the amount of delegated bandwidth provided in the Bandwidth-
Allocation TLV is not greater than the NAS's view of the current
amount of delegated bandwidth, the NAS MUST update its view of the
current amount of delegated bandwidth to the amount indicated in the
Bandwidth Transfer message. This is required regardless of whether
the Result field of that message indicates Success or Failure.
If the amount of delegated bandwidth provided in the Bandwidth-
Allocation TLV is greater than the NAS's view of the current amount
of delegated bandwidth, the NAS MAY accept the given value as its new
value of delegated bandwidth. Alternatively, the NAS MAY force the
AN to modify its view of the amount of delegated bandwidth to that
held by the NAS, by sending a Port Management message for the target
access line concerned, containing a Bandwidth-Allocation TLV with a
value equal to the amount of delegated bandwidth the NAS wishes to
enforce.
Le Faucheur, et al. Expires September 9, 2010 [Page 30]
Internet-Draft ANCP Multicast Extensions March 2010
4.6.2.2. Behaviour of the AN
If the amount of delegated bandwidth provided in the Bandwidth-
Allocation TLV of the Bandwidth Transfer message differs from the
AN's view of the current amount of delegated bandwidth, the AN MUST
update its view of the current amount of delegated bandwidth to the
amount indicated in the Bandwidth Transfer message. This is required
with the exception of a Bandwidth Transfer message with a Result
field equal to Failure (0x4) and a Code field equal to 104
"Inconsistent views of delegated bandwidth amount" or 105 "Bandwidth
request conflict". If Code value 104 is received, the AN MUST issue
a Delegated Bandwidth Query Request message to determine the NAS's
current view of the amount of delegated bandwidth. The AN MUST
update its own view based on the value returned in the Delegated
Bandwidth Query Response. If Code value 105 is received, the AN
SHOULD carry out this procedure unless it can account for the
discrepancy as a result of a transfer of bandwidth to the NAS that
was carried out just before the incoming Bandwidth Transfer message
was processed.
The two Code values indicate a race condition where the AN may
have just completed a transfer of bandwidth to the NAS. As a
result, the value given in the Bandwidth Transfer message may be
outdated, and the AN needs to query the NAS to find its latest
view. The procedure assumes that ordering is preserved between
the Bandwidth Transfer message sent by the AN in response to the
NAS's request and the subsequent Delegated Bandwidth Query Request
message.
If as the result of the procedures just described the AN determines
that it has over-committed multicast bandwidth, it MUST NOT terminate
any currently-active programs, but MUST NOT honour any more "join"
requests until it is possible to do so within the limit set by its
current value of delegated bandwidth.
4.7. Delegated Bandwidth Query Request Message
The Message Type for the Delegated Bandwidth Query Request (and
Response) messages is 148.
The Delegated Bandwidth Query Request message MAY be sent either by
the NAS or by the AN to retrieve the peer's view of the amount of
delegated bandwidth. The request contains one TLV:
o a Target TLV designating the access line for which the information
is requested.
Le Faucheur, et al. Expires September 9, 2010 [Page 31]
Internet-Draft ANCP Multicast Extensions March 2010
4.7.1. Sender Behaviour
The sender MUST set the Result field in the header of the Delegated
Bandwidth Query Request message to AckAll (0x2). The Code value MUST
be set to 0x000. The sender MUST populate the ANCP Transaction
Identifier field with a unique value, as described in section 5.4.5
of [I-D.ietf-ancp-protocol].
4.7.2. Receiver Behaviour
If the AN or NAS receives a valid Delegated Bandwidth Query Request
message, it MUST respond with a Delegated Bandwidth Query Response
message. The Result field in the header of the response MUST be set
to Success (0x3). The Code field MUST be set to 0x000. The
Transaction-Id field MUST be copied from the request message. The
body of the response MUST contain the Target TLV, copied from the
request message. Finally, the body of the response MUST contain a
Bandwidth-Allocation TLV, containing the current amount of delegated
bandwidth from the point of view of the receiver of the request.
If the contents of the Delegated Bandwidth Query Request message are
in error, the receiver MUST return a Delegated Bandwidth Query
Response message with the Result field in the header set to Failure
(0x3). The Code field MUST be set to the value that indicates the
nature of the error (e.g., 4 "Unrecognized target"). The
Transaction-Id field MUST be copied from the request. The body of
the response MUST contain the Target TLV copied from the request.
This MAY be followed by a Status-Info TLV giving further information
about the error.
4.8. Delegated Bandwidth Query Response Message
The Delegated Bandwidth Query Response message is sent in reply to a
Delegated Bandwidth Query Request. The response to a valid request
contains two TLVs:
o the Target TLV, copied from the request;
o a Bandwidth-Allocation TLV, giving the responder's view of the
current amount of multicast bandwidth delegated to the AN.
The Message Type for the Delegated Bandwidth Query Response message
is 148.
4.8.1. Sender Behaviour
Sender behaviour for the Delegated Bandwidth Query Response message
is specified in Section 4.7.2.
Le Faucheur, et al. Expires September 9, 2010 [Page 32]
Internet-Draft ANCP Multicast Extensions March 2010
4.8.2. Receiver Behaviour
If the Delegated Bandwidth Query Response message indicates Success
(0x3), the following actions apply.
4.8.2.1. Behaviour at the NAS
If the amount of delegated bandwidth provided in the Bandwidth-
Allocation TLV is less than the NAS's view of the current amount of
delegated bandwidth, the NAS MUST update its view of the current
amount of delegated bandwidth to the amount indicated in the
Delegated Bandwidth Query Response message.
If the amount of delegated bandwidth provided in the Bandwidth-
Allocation TLV is greater than the NAS's view of the current amount
of delegated bandwidth, the NAS MAY accept the given value as its new
value of delegated bandwidth. Alternatively, the NAS MAY force the
AN to modify its view of the amount of delegated bandwidth to that
held by the NAS, by sending a Port Management message for the target
access line concerned, containing a Bandwidth-Allocation TLV with a
value equal to the amount of delegated bandwidth the NAS wishes to
enforce.
4.8.2.2. Behaviour at the AN
The AN SHOULD accept the value returned in the Bandwidth-Allocation
TLV of the Delegated Bandwidth Query Response message as the correct
value of the current amount of delegated bandwidth. If the AN has
currently committed more than this amount to active programs, it MUST
NOT cease replicating the flows concerned, but MUST NOT honour any
more Join requests until possible to do so within the new limit.
A race condition is possible, where the AN sends a query, the NAS
requests more bandwidth, then receives and responds to the query,
then receives the Bandwidth Transfer message responding to its
request. It is up to the AN to take appropriate action in this
case. The best action appears to be not to act on the result of
the first query, but to repeat the query after sending the
Bandwidth Transfer message. Similar considerations apply to a
race between queries from both sides.
4.9. Multicast Flow Query Request and Response Messages
This section defines two new messages called the Multicast Flow Query
Request and Multicast Flow Query Response. The Multicast Flow Query
Request is sent by the NAS to request information about the multicast
flows that are active on the AN. The Multicast Flow Query Response
is sent in response by the AN to provide the requested information to
Le Faucheur, et al. Expires September 9, 2010 [Page 33]
Internet-Draft ANCP Multicast Extensions March 2010
the NAS.
The Message Type for the Multicast Flow Query Request and Multicast
Flow Query Response messages is 149.
The contents of the Multicast Flow Query Request and Response depend
on the nature of the query, as described below.
4.9.1. Sender Behaviour
The sender of a Multicast Flow Query Request message MUST set the
Result field to AckAll (0x2). The Code field MUST be set to 0x000.
The sender MUST populate the ANCP Transaction Identifier field with a
unique value, as described in section 5.4.5 of [I-D.ietf-ancp-
protocol].
The Multicast Flow Query Request MAY be used by the NAS to retrieve:
o the AN's view of which multicast flows are currently active on a
specified set of access ports; or
o the AN's view of the access ports on which a specified set of
multicast flows are currently active; or
o the AN's view of all the multicast flows currently active on each
and every port of the AN.
To retrieve the AN's view of which multicast flows are currently
active on a given port of the AN, the NAS MUST include a Target TLV
in the Multicast Flow Query Request payload identifying that port.
The Target TLV is encoded as specified in [I-D.ietf-ancp-protocol].
To retrieve the AN's view of the ports currently receiving a given
multicast flow, the NAS MUST include a Multicast-Flow TLV in the
Multicast Flow Query Request payload identifying that flow. The
Multicast-Flow TLV is encoded as specified in Section 5.11.
The NAS MAY include multiple Target TLVs or multiple Multicast-Flow
TLVs in the Multicast Flow Query Request, but MUST NOT include both
Target and Multicast-Flow TLVs in the same message.
To retrieve the AN's view of all of the multicast flows currently
active on each port of the AN, the NAS MUST send a Multicast Flow
Query Request which does not contain any instance of the Target TLV
or the Multicast-Flow TLV.
Le Faucheur, et al. Expires September 9, 2010 [Page 34]
Internet-Draft ANCP Multicast Extensions March 2010
4.9.2. Receiver Behaviour
The AN MUST respond to a Multicast Flow Query Request message that
has a valid format and a valid content with a Multicast Flow Query
Response message. The Result field in the response MUST be set to
Success (0x3). The Code field MUST be set to 0x000. The
Transaction-Id field MUST be copied from the request.
If the Multicast Flow Query Request contained one (or more) Target
TLVs, the AN MUST include, for each of these Target TLVs, the
following set of TLVs:
o Target TLV. This MUST be identical to the Target TLV in the
received Multicast Flow Query Request message.
o Multicast-Flow TLV(s). The Multicast-Flow TLV MUST appear once
per multicast flow that is currently active on the AN port
identified in the preceding Target TLV.
The Target TLVs MUST appear in the response from the AN in the same
order as in the query from the NAS.
If the Multicast Flow Query Request contained one (or more)
Multicast-Flow TLVs, the AN MUST include, for each of these
Multicast-Flow TLVs, the following set of TLVs:
o Multicast-Flow TLV. This MUST be identical to the Multicast-Flow
TLV in the received Multicast Flow Query Request message.
o Target TLV(s). The Target TLV MUST appear once per AN port on
which the multicast flow identified in the preceding Multicast
Flow TLV is active.
The Multicast-Flow TLVs MUST appear in the response from the AN in
the same order as in the query from the NAS.
If the Multicast Flow Query Request contained no Target TLV and no
Multicast Flow TLV, the AN MUST include, for each AN port currently
receiving multicast flow(s), the following set of TLVs:
o Target TLV. This MUST identify one AN port.
o Multicast-Flow TLV(s). The Multicast-Flow TLV MUST appear once
per Multicast Flow that is currently active on the AN port
identified in the preceding Target TLV.
If the contents of the Multicast Flow Query Request are in error, the
AN MUST reply with a Multicast Flow Query Response message with the
Le Faucheur, et al. Expires September 9, 2010 [Page 35]
Internet-Draft ANCP Multicast Extensions March 2010
Result field set to Failure (0x4) and the Code field set to indicate
the nature of the error. If the request contained multiple instances
of the Target TLV or the Multicast-Flow TLV and one of these is in
error, the response message MUST contain the results for the
preceding instances of the TLV as if there had been no error. These
successful results MUST be followed by the TLV in error, copied from
the request. The AN MUST NOT do further processing of the request.
The AN MAY add a Status-Info TLV to provide further information on
the nature of the error.
The amount of information in the response to the Multicast Flow Query
Request may be very large. The AN MAY pass the information in a
series of Multicast Flow Query Response messages so that the control
channel to the NAS is not blocked for too long by transmission of a
single very large message. To support this, the receiver MUST set
the I flag and Submessage Number fields in the header of each
Multicast Flow Query Response message making up the complete response
in accordance with the usage of these fields as described in Section
3.1.1 of [RFC3292]. That is, the initial Multicast Flow Query
Response message in the sequence MUST have the I flag set (0x1) and
the Submessage Number field value equal to the total number of
messages making up the complete response. The remaining messages in
the sequence MUST have the I flag cleared (0x0) and the Submessage
Number field value set to the sequence number of the message within
the complete sequence, counting from 2 for the second message in the
sequence. Moreover, every message in the sequence except the last
one MUST have the Result field value equal to "More" (0x5). The
final message in the response MUST have the Result field set to
Success (0x3) or Failure (0x4) as the case may be. The ordering of
the messages in the sequence MUST be such that they present the
contents in the same order as if all of the information had been
presented in just one message, according to the rules described
above.
Le Faucheur, et al. Expires September 9, 2010 [Page 36]
Internet-Draft ANCP Multicast Extensions March 2010
5. ANCP TLVs For Multicast
This section defines new ANCP TLVs for the control of multicast
flows.
5.1. Multicast-Service-Profile TLV
This document defines the new Multicast-Service-Profile TLV.
The Multicast-Service-Profile TLV MAY be included in a Provisioning
message as specified in Section 4.1.
The Multicast-Service-Profile TLV is illustrated in Figure 5. It
consists of a TLV header encapsulating a single instance of the
Multicast-Service-Profile-Name TLV and one or more instances of the
List-Action TLV.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Mcast Serv Profile | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast-Service-Profile-Name TLV |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List-Action TLV |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List-Action TLV |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Multicast-Service-Profile TLV
The Multicast-Service-Profile TLV has the following fields:
o The Multicast-Service-Profile TLV Type is 0x13.
o The TLV length is determined by the contents following the TLV
header.
o The Multicast-Service-Profile-Name TLV is described in
Section 5.2. The Multicast-Service-Profile-Name TLV MUST contain
an identifier which is unique over all profiles provisioned to the
same AN partition. This identifier will be used to refer to the
Le Faucheur, et al. Expires September 9, 2010 [Page 37]
Internet-Draft ANCP Multicast Extensions March 2010
profile when activating it for a given target within a Port
Management message (see Section 4.2).
o The List-Action TLV is described in Section 5.3. The List-Action
TLV(s) provide the content of a newly defined multicast service
profile or modify the existing content. If more than one List-
Action TLV is present, the order of the TLVs may be significant,
since List-Action TLVs are processed in the order in whch they
appear.
5.2. Multicast-Service-Profile-Name TLV
The Multicast-Service-Profile-Name TLV carries the identifier of a
multicast service profile provisioned on the AN. It is illustrated
in Figure 6.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = MSP Name | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast service profile identifier |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Multicast-Service-Profile-Name TLV
The Multicast-Service-Profile-Name TLV has the following fields:
o The Multicast-Service-Profile-Name TLV Type is 0x18.
o TLV Length: up to 255 octets.
o Multicast service profile identifier: an opaque sequence of bits
identifying a specific multicast service profile.
The identifier could have the form of human-readable text or an
arbitrary binary value, depending on the operator's practices.
5.3. List-Action TLV
The List-Action TLV identifies multicast flows to be added to or
removed from a list of White-, Black-, or Grey-listed flows. It is
meaningful only in association with a Multicast-Service-Profile-Name
TLV identifying the profile to which the List-Action TLV applies.
Such an association can be achieved by placing both TLVs in the same
base message payload or as embedded TLVs of another TLV such as the
Multicast-Service-Profile. The List-Action TLV is shown in Figure 7.
Le Faucheur, et al. Expires September 9, 2010 [Page 38]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = List-Action TLV | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Operation | List Type | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Family | Number of flow fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast flow fields |
......
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Family | Number of flow fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast flow fields |
......
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: List-Action TLV
The List-Action TLV contains the following fields:
o The List-Action TLV Type is 0x21.
o TLV Length: length of the subsequent contents.
o Operation: operation to be performed upon the White, Black, or
Grey list identified by the List Type field within the profile
identified by the associated Multicast-Service-Profile-Name
embedded TLV. The possible values are:
* Add (0x01): the multicast flow fields are to be added to the
list.
* Delete (0x02): the multicast flow fields are to be removed from
the list. Each multicast flow field in the List-Action MUST
match exactly an existing entry in the list concerned. Thus to
remove part of the range provided by a wildcarded list entry,
it is necessary to remove the entire entry and add back the
remaining partial range(s).
* Replace (0x03): the multicast flow fields replace the existing
contents of the list.
Le Faucheur, et al. Expires September 9, 2010 [Page 39]
Internet-Draft ANCP Multicast Extensions March 2010
o List Type: the list type being modified by this List-Action. The
possible values are White (0x01), Black (0x02), or Grey (0x03).
o Reserved: a sender MUST set this field to 0x0000. A receiver MUST
ignore the contents of this field.
o Address Family: the IP version of the set of multicast flow fields
that follow, encoded according to [PIMreg]. Possible values are
0x0001 (IPv4) or 0x0002 (IPv6). Either an IPv4 list or an IPv6
list or both MAY be present in the List-Action TLV.
o Number of flow fields: the number of multicast flow fields of the
given address family which follow.
o Multicast flow field: a field identifying one or more multicast
flows. It consists of an 8-bit group address prefix length, an
8-bit source address prefix length, a 0-16 octet group prefix, and
a 0-16 octet source prefix, as shown in Figure 8.
Each multicast flow field refers either to a Source-Specific
Multicast (SSM) channel or to an Any Source Multicast (ASM) group.
The scope of the designation may be broadened to multiple channels or
groups through use of prefix length values smaller than the total
address length for the given address family. Multicast flow fields
MUST be placed consecutively within the embedded TLV without
intervening padding except to round out individual addresses to the
nearest octet boundary.
A multicast flow field consists of two single-octet prefix lengths
followed by zero to two prefix values as shown in Figure 8:
+-+-+-+-+-+-+-+-+
| Group PrefLen |
+-+-+-+-+-+-+-+-+
| Source PrefLen|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group Prefix (multicast) (0 to 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Prefix (unicast, SSM only) (0 to 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8: Organization of a Single Multicast Flow Field
The prefix length has its usual meaning. It is the number of most-
significant bits specified within the corresponding prefix. The
prefix length MAY vary from 0 to 32 in the IPv4 sub-list, and from 0
to 128 in the IPv6 sub-list.
Le Faucheur, et al. Expires September 9, 2010 [Page 40]
Internet-Draft ANCP Multicast Extensions March 2010
A value of 0x00 for either the Group PrefLen (prefix length) or the
Source PrefLen indicates that any value of the corresponding address
will match (wild card). If the value 0x00 is provided for a
particular prefix length, the corresponding prefix MUST be omitted
from the field contents. In particular, a value of 0x00 for the
Source PrefLen indicates an ASM multicast entry, and the Source
Prefix will be absent.
The length of a Source or Group Prefix field is equal to (PrefLen +
7)/8 octets, truncated to the nearest integer. Unused bits at the
end of the prefix MUST be set to zeroes.
5.4. Sequence-Number TLV
The Sequence-Number TLV conveys a sequence number of some sort. The
specific meaning of the sequence number is message-specific. Within
this specification, the Sequence-Number TLV is used as a embedded TLV
within a Status-Info TLV, in a Generic Response reporting a failed
command within a Multicast Replication Control or Multicast Admission
Request message. It identifies the sequence number within the
message of the command that failed.
The Sequence-Number TLV has the format shown in Figure 9.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Sequence-Number | TLV Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9: Sequence-Number TLV
The Sequence-Number TLV has the following fields:
o The Sequence-Number TLV Type is 0x22.
o TLV length is 0x0004.
o Sequence number: the sequence number of a specific entity within a
series, where numbering starts from 1 for the first entity in the
series. Represented as a 32-bit binary number, most significant
bit first.
Le Faucheur, et al. Expires September 9, 2010 [Page 41]
Internet-Draft ANCP Multicast Extensions March 2010
5.5. Bandwidth-Allocation TLV
The Bandwidth-Allocation TLV is used to indicate the total amount of
video bandwidth delegated to the AN for multicast admission control
for a given access line, in kilobits per second. The TLV has the
format shown in Figure 10.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = BW-Allocation | TLV Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Delegated amount (kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10: The Bandwidth-Allocation TLV
The Bandwidth-Allocation TLV has the following fields:
o The Bandwidth-Allocation TLV Type is 0x15.
o TLV length is 4.
o Delegated amount: the bandwidth amount delegated to the AN for
admission of multicast video on a given port, kilobits per second.
Presented as a 32-bit binary value, most significant bit first.
5.6. White-List-CAC TLV
The White-List-CAC TLV is used to indicate that the NAS wishes the AN
to do admission control for White-listed flows. Details on when the
White-List-CAC TLV may be provisioned are specified in Section 6.
The White-List-CAC TLV is illustrated in Figure 11.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = White-List-CAC | TLV Length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: White-List-CAC TLV
The White-List-CAC TLV contains the following fields:
o The White-List-CAC TLV Type is 0x24.
o TLV length is 0, since the TLV contains no data other than the TLV
header.
Le Faucheur, et al. Expires September 9, 2010 [Page 42]
Internet-Draft ANCP Multicast Extensions March 2010
5.7. MRepCtl-CAC TLV
The MRepCtl-CAC TLV is used to indicate that the NAS wishes the AN to
do admission control for flows added by the Multicast Replication
Control message. Details on when the MRepCtl-CAC TLV may be
provisioned are specified in Section 6. The MRepCtl-CAC TLV is
illustrated in Figure 12.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = MRepCtl-CAC | TLV Length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 12: MRepCtl-CAC TLV
The MRepCtl-CAC TLV contains the following fields:
o The MRepCtl-CAC TLV Type is 0x25.
o TLV length is 0, since the TLV contains no data other than the TLV
header.
5.8. Bandwidth-Request TLV
The Bandwidth-Request TLV is used to request an adjustment of the
total amount of video bandwidth allocated to the AN for multicast
admission control for a given line. The "Required amount" field
indicates the minimum adjustment required to meet the request. The
"Preferred amount" field indicates the adjustment the requestor would
prefer to have, if possible. Section 4.5 discusses the required
relationships between the "Required amount", "Preferred amount", and
current values of total bandwidth allocated to the AN.
The Bandwidth-Request TLV has the format shown in Figure 13.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Bandwidth-Request | TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Required amount (kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Preferred amount (kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 13: The Bandwidth-Request TLV
Le Faucheur, et al. Expires September 9, 2010 [Page 43]
Internet-Draft ANCP Multicast Extensions March 2010
The Bandwidth-Request TLV has the following fields:
o The Bandwidth-Request TLV Type is 0x16.
o The TLV length is 8 octets.
o Required amount: the minimum or maximum amount, depending on
whether the sender is the AN or the NAS respectively, of delegated
video bandwidth that is being requested, in kilobits per second.
Presented as a 32-bit binary value, most significant bit first.
o Preferred amount: the preferred amount of delegated video
bandwidth that is being requested, in kilobits per second.
Presented as a 32-bit binary value, most significant bit first.
5.9. Request-Source-IP TLV
The Request-Source-IP TLV provides the IP address of the entity that
originated a specific request to join or leave a multicast channel.
The TLV is illustrated in Figure 14.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = Request-Source-IP | TLV length = 4 or 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 14: Request-Source-IP TLV
The Request-Source-IP TLV contains the following fields:
o The Request-Source-IP TLV Type is 0x92.
o TLV length is 4 for an IPv4 address or 16 for an IPv6 address.
o Unicast address: IP address of the source of a multicast flow join
request, in network byte order.
5.10. Request-Source-MAC TLV
The Request-Source-MAC TLV provides the MAC address of the entity
that originated a specific request to join or leave a multicast
channel. The TLV is illustrated in Figure 15.
Le Faucheur, et al. Expires September 9, 2010 [Page 44]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type=Request-Source-MAC | TLV Length = 6 or 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IEEE MAC Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 15: Request-Source-MAC TLV
The Request-Source-MAC TLV contains the following fields:
o The Request-Source-MAC TLV Type is 0x93.
o TLV length is either 6 octets (MAC-48 or EUI-48) or 8 octets
(EUI-64).
o IEEE MAC Address: MAC address of the device originating the
request to join a multicast flow. Within the address, bytes and
bits respectively shall be ordered from most to least significant,
consistently with [IEEE48] for MAC-48 and EUI-48, and with
[IEEE64] for EUI-64.
EUI-48 and EUI-64 are registered trademarks of the IEEE.
5.11. Multicast-Flow TLV
The Multicast-Flow TLV specifies a multicast flow in terms of its
multicast group address and, if applicable, its unicast source
address. It is illustrated in Figure 16.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TLV Type = Multicast-Flow | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flow Type | Addr Family | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
| Unicast Source Address (for SSM flows only) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 16: Multicast-Flow TLV
The Multicast-Flow TLV has the following fields:
Le Faucheur, et al. Expires September 9, 2010 [Page 45]
Internet-Draft ANCP Multicast Extensions March 2010
o The Multicast-Flow TLV Type is 0x19.
o TLV Length: ranges from a minimum of 8 (for an ASM IPv4 flow) to
36 (for an IPv6 SSM flow.
o Flow Type: 0x01 for Any Source Multicast (ASM), 0x02 for Specific-
Source Multicast (SSM).
o Addr Family: address family of the multicast source and group
addresses, encoded in accordance with the IANA PIM Address Family
registry ([PIMreg]). 0x01 indicates IPv4, 0x02 indicates IPv6.
o Reserved: MUST be set to 0x0000 by the sender and MUST be ignored
by the receiver.
One possible use for this field in the future is to indicate
the presence of PIM Join attributes attached to the source
address (see [RFC5384]). The applicability of PIM attributes
in the context of ANCP is for further study.
o Multicast Group Address: a multicast group address within the
given address family. The group address MUST always be present.
o Unicast Source Address: unicast address within the given address
family. If the Flow Type is 0x01 (ASM), a source address MUST NOT
be present. If the Flow Type is 0x02 (SSM), a source address MUST
be present.
Le Faucheur, et al. Expires September 9, 2010 [Page 46]
Internet-Draft ANCP Multicast Extensions March 2010
6. Multicast Capabilities
Section 5.3 of [I-D.ietf-ancp-protocol] defines a capability
negotiation mechanism as well as a number of capabilities. This
section defines four new capabilities in support of different modes
of multicast operation:
o NAS-initiated replication (capability type 0x05);
o conditional access with white and black lists (capability type
0x06);
o conditional access with grey lists (capability type 0x07);
o bandwidth delegation (capability type 0x08).
The "Capability Data" field within the Capability TLV for all of
these capabilities is empty.
The remainder of this section consists of three sub-sections.
Section 6.1 specifies the protocol elements that must be implemented
in order to support each capability. Section 6.2 specifies the
procedures that apply to each capability on its own. Section 6.3
specifies how the capabilities interact if more than one multicast
capability is included in the set of capabilities negotiated between
the AN and the NAS.
Note that if a request contains content that is not supported
(according to the tables in Section 6.1) by the negotiated set of
multicast capabilities, the appropriate response is to return a
Generic Response message indicating Failure (0x4) with an appropriate
code value (e.g., 84 "TLV or value not supported by negotiated
capability set"). The body of the message MUST contain a Status-Info
TLV. See Sections 5.4.5.1 and 5.4.5.2 in [I-D.ietf-ancp-protocol]
for more details.
6.1. Required Protocol Support
This section specifies the protocol elements that MUST be implemented
to support each of the four multicast capabilities. Support of
multiple multicast capabilities requires implementation of the union
of the sets of protocol elements applying to each of the individual
capabilities in the supported set.
6.1.1. Protocol Requirements For NAS-initiated Replication
Table 1 specifies the protocol elements within Section 4 and
Section 5 that MUST be implemented to support the NAS-initiated
Le Faucheur, et al. Expires September 9, 2010 [Page 47]
Internet-Draft ANCP Multicast Extensions March 2010
replication multicast capability.
+--------------+----------------------------------------------------+
| Reference | Protocol Element |
+--------------+----------------------------------------------------+
| Section 4.1 | Provisioning message with MRepCtl-CAC TLV |
| | |
| Section 4.2 | Port Management message with Bandwidth-Allocation |
| | TLV. |
| | |
| Section 4.3 | Multicast Replication Control message |
| | |
| Section 4.9 | Multicast Flow Query Request and Response messages |
| | |
| Section 5.4 | Command Number TLV |
| | |
| Section 5.7 | MRepCtl-CAC TLV |
| | |
| Section 5.11 | Multicast-Flow TLV |
+--------------+----------------------------------------------------+
Table 1: Protocol Requirements For NAS-initiated Replication
6.1.2. Protocol Requirements For Conditional Access With White and
Black Lists
Table 2 specifies the protocol elements within Section 4 and
Section 5 that MUST be implemented to support the conditional access
with white and black lists multicast capability.
Le Faucheur, et al. Expires September 9, 2010 [Page 48]
Internet-Draft ANCP Multicast Extensions March 2010
+--------------+----------------------------------------------------+
| Reference | Protocol Element |
+--------------+----------------------------------------------------+
| Section 4.1 | Provisioning message with |
| | Multicast-Service-Profile TLV, White and Black |
| | lists only, and White-List-CAC TLV |
| | |
| Section 4.2 | Port Management message with |
| | Multicast-Service-Profile-Name and |
| | Bandwidth-Allocation TLVs. |
| | |
| Section 4.9 | Multicast Flow Query Request and Response messages |
| | |
| Section 5.1 | Multicast-Service-Profile TLV |
| | |
| Section 5.2 | Multicast-Service-Profile-Name TLV |
| | |
| Section 5.3 | List-Action TLV, White and Black lists only |
| | |
| Section 5.5 | Bandwidth-Allocation TLV |
| | |
| Section 5.6 | White-List-CAC TLV |
| | |
| Section 5.11 | Multicast-Flow TLV |
+--------------+----------------------------------------------------+
Table 2: Protocol Requirements For Conditional Access with White and
Black Lists
6.1.3. Protocol Requirements For Conditional Access With Grey Lists
Table 3 specifies the protocol elements within Section 4 and
Section 5 that MUST be implemented to support the conditional access
with grey lists multicast capability.
Le Faucheur, et al. Expires September 9, 2010 [Page 49]
Internet-Draft ANCP Multicast Extensions March 2010
+--------------+----------------------------------------------------+
| Reference | Protocol Element |
+--------------+----------------------------------------------------+
| Section 4.1 | Provisioning message with |
| | Multicast-Service-Profile TLV, Grey lists only, |
| | and MRepCtl-CAC TLV |
| | |
| Section 4.2 | Port Management message with |
| | Multicast-Service-Profile-Name and |
| | Bandwidth-Allocation TLVs. |
| | |
| Section 4.3 | Multicast Replication Control message |
| | |
| Section 4.4 | Multicast Admission Control Message |
| | |
| Section 4.9 | Multicast Flow Query Request and Response messages |
| | |
| Section 5.1 | Multicast-Service-Profile TLV, Grey lists only |
| | |
| Section 5.2 | Multicast-Service-Profile-Name TLV |
| | |
| Section 5.3 | List-Action TLV, Grey lists only |
| | |
| Section 5.4 | Command Number TLV |
| | |
| Section 5.5 | Bandwidth-Allocation TLV |
| | |
| Section 5.7 | MRepCtl-CAC TLV |
| | |
| Section 5.9 | Request-Source-IP TLV |
| | |
| Section 5.10 | Request-Source-MAC TLV |
| | |
| Section 5.11 | Multicast-Flow TLV |
+--------------+----------------------------------------------------+
Table 3: Protocol Requirements For Conditional Access with Grey Lists
6.1.4. Protocol Requirements For Delegated Bandwidth
Table 4 specifies the protocol elements within Section 4 and
Section 5 that MUST be implemented to support the delegated bandwidth
multicast capability.
Le Faucheur, et al. Expires September 9, 2010 [Page 50]
Internet-Draft ANCP Multicast Extensions March 2010
+--------------+----------------------------------------------------+
| Reference | Protocol Element |
+--------------+----------------------------------------------------+
| Section 4.2 | Port Management message with Bandwidth-Allocation |
| | TLV. |
| | |
| Section 4.5 | Bandwidth Reallocation Request Message |
| | |
| Section 4.6 | Bandwidth Transfer Message |
| | |
| Section 4.7 | Delegated Bandwidth Query Request Message |
| | |
| Section 4.8 | Delegated Bandwidth Query Response Message |
| | |
| Section 4.9 | Multicast Flow Query Request and Response messages |
| | |
| Section 5.5 | Bandwidth-Allocation TLV |
| | |
| Section 5.8 | Bandwidth-Request TLV |
| | |
| Section 5.11 | Multicast-Flow TLV |
+--------------+----------------------------------------------------+
Table 4: Protocol Requirements For Delegated Bandwidth
6.2. Capability-Specific Procedures for Providing Multicast Service
This section describes multicast service procedures for each
capability as if it were the only multicast capability within the
negotiated set. Procedures involving combinations of multicast
capabilities are described in Section 6.3.
The use of the Multicast Flow Query Request and Response messages to
determine the association between multicast flows and ports is common
to all multicast capabilities. No additional text is required here,
beyond that already given in Section 4.9 to describe the use of those
messages.
6.2.1. Procedures For NAS-initiated Replication
NAS-initiated replication MAY be negotiated to support a mode of
operation where IGMP/MLD requests are terminated on the NAS.
Alternatively, it MAY be negotiated to allow the NAS to respond to
requests sent by other means (e.g., through application signalling)
that require the replication of multicast channels to a given access
line.
Le Faucheur, et al. Expires September 9, 2010 [Page 51]
Internet-Draft ANCP Multicast Extensions March 2010
6.2.1.1. Provisioning
The NAS MAY perform admission control for NAS-initiated replication.
In this case, it MUST NOT include the MRepCtl-CAC TLV in a
Provisioning message sent to the AN. Alternatively, the NAS MAY
enable admission control at the AN for NAS-initiated replication. To
do this, it MUST include the MRepCtl-CAC TLV in a Provisioning
message sent to the AN and it MUST also include a Bandwidth-
Allocation TLV in a Port Management message for each access line.
6.2.1.2. Multicast Service Procedures
The procedures associated with NAS-initiated replication are
straightforward. To initiate replication, the NAS MUST send a
Multicast Replication Control message to the AN, containing one or
more commands adding flows, as described in Section 4.3.1. To
terminate replication the NAS MUST send a Multicast Replication
Control message where the commands delete instead of adding the
flows. The AN acts upon these messages as specified in
Section 4.3.2.
6.2.2. Procedures For Conditional Access With Black and White Lists
6.2.2.1. Provisioning
The NAS provisions named multicast service profiles containing White
and Black lists on the AN using the Provisioning message containing
one or more Multicast-Service-Profile TLVs. The NAS MAY update the
contents of these profiles from time to time as required, by sending
additional Provisioning messages with Multicast-Service-Profile TLVs
containing incremental modifications to the existing White and Black
lists or replacements for them.
The NAS assigns a specific multicast service profile to an individual
access line using the Port Management message containing a Multicast-
Service-Profile-Name TLV. The NAS MAY change the multicast service
profile for a given access line at any time by sending a Port
Management message identifying a new multicast service profile.
The NAS MAY choose to enable admission control at the AN for White-
listed flows. To do this, it MUST send a Provisioning message as
described in Section 4.1, which includes the White-List-CAC TLV and
it MUST provide a multicast bandwidth allocation for each access line
by including a Bandwidth-Allocation TLV in a Port Management message.
Le Faucheur, et al. Expires September 9, 2010 [Page 52]
Internet-Draft ANCP Multicast Extensions March 2010
6.2.2.2. Multicast Service Procedures
The conditional access with White and Black lists capability assumes
that IGMP/MLD requests are terminated on the AN. When the AN
receives a "join" request, it MUST check to see whether the requested
flow is White-listed or Black-listed as described below. Requests
for Black-listed flows MUST be discarded. If the NAS has enabled
admission control on the AN as described in the previous section, but
a White-listed flow would cause the amount of committed multicast
bandwidth to exceed the provisioned limit, the request MUST be
discarded. The AN replicates flows passing these checks to the
access line.
To determine if a requested flow is White-listed, the AN searches for
a best match to the flow in the applicable multicast service profile.
Matching is done on the prefixes specified in the profile, ignoring
the address bits of lower order than those in the prefix.
If the requested multicast flow matches multiple lists associated
with the access line, then the most specific match will be considered
by the AN. If the most specific match occurs in multiple lists, the
Black list entry takes precedence over the White list. In this
context, the most specific match is defined as:
o first, most specific match (longest prefix length) on the
multicast flow address (i.e., on G of <S,G>)
o then, most specific match (longest prefix length) on the unicast
source address (i.e. on S of <S,G>)
If the requested multicast flow is not part of any list, the join
message SHOULD be discarded by the AN. This default behavior can
easily be changed by means of a "catch-all" statement in the White
list. For instance, adding (<S=*,G=*>) in the White List would make
the default behavior to accept join messages for a multicast flow
that has no other match on any list.
When the AN receives a "leave" request, it terminates replication of
the multicast flow.
If the AN receives a Provisioning message which updates an existing
multicast service profile, the AN MUST review the status of active
flows on all ports to which the updated profile is currently
assigned. Similarly, if a Port Management message assigns a new
multicast service profile to a given port, the AN MUST review all
active flows on that port. If the most specific match for any flow
is a Black list entry, the flow MUST be terminated immediately. If
any of the remaining flows do not match an entry in the White list,
Le Faucheur, et al. Expires September 9, 2010 [Page 53]
Internet-Draft ANCP Multicast Extensions March 2010
they also MUST be terminated immediately. White listed flows MUST be
allowed to continue.
6.2.3. Procedures For Conditional Access With Grey Lists
6.2.3.1. Provisioning
The NAS provisions named multicast service profiles containing Grey
lists on the AN using the Provisioning message containing one or more
Multicast-Service-Profile TLVs. The NAS MAY update the contents of
these profiles from time to time as required, by sending additional
Provisioning messages with Multicast-Service-Profile TLVs containing
incremental modifications to the existing Grey lists or replacements
for them.
The NAS assigns a specific multicast service profile to an individual
access line using the Port Management message containing a Multicast-
Service-Profile-Name TLV. The NAS MAY change profiles on the line by
sending a subsequent Port Management message identifying a new
profile.
The NAS MAY perform admission control for grey-listed flows. In that
case, the NAS MUST NOT include the MRepCtl-CAC TLV in a Provisioning
message sent to the AN. Alternatively, the NAS MAY enable admission
control at the AN for Grey-listed flows. To do this, it MUST include
the MRepCtl-CAC TLV in a Provisioning message sent to the AN and MUST
also provide a Bandwidth-Allocation TLV in a Port Management message
for each access line.
6.2.3.2. Multicast Service Procedures
The conditional access with Grey lists capability assumes that IGMP/
MLD requests are terminated on the AN. When the AN receives a "join"
request, it MUST determine whether there is a match to the requested
flow in the Grey list of the multicast service profile provisioned
against the given access line. If there is no match, the request is
discarded. Otherwise, the AN MUST send a Multicast Admission Control
message to the NAS with content identifying the access line and the
multicast flow to be added. As indicated in Section 4.4, the AN MAY
add information identifying the requestor by IP address and/or MAC
address.
If the NAS decides to enable the flow, it MUST send a Multicast
Replication Control request to the AN to replicate the flow to the
access line with the Result field set to Nack (0x1), as described in
Section 4.3.1.
When the AN receives the Multicast Replication Control request, it
Le Faucheur, et al. Expires September 9, 2010 [Page 54]
Internet-Draft ANCP Multicast Extensions March 2010
performs admission control if admission control has been enabled as
described in the previous section. If admitting the flow would cause
the committed multicast bandwidth at the access line to exceed the
provisioned limit, the AN reports an error to the NAS as described in
Section 4.3.2. Otherwise it replicates the multicast flow as
requested.
If the NAS decides not to permit the flow, it MAY send a Multicast
Replication Control message in response to the Multicast Admission
Control message to allow the AN to update its internal records. The
content of this message is described in Section 4.4.2.
When the AN receives a "leave" request, it MUST terminate replication
of the flow to the access line. It MUST then send a Multicast
Admission Control message to the NAS indicating the deletion. The
NAS updates its internal records but MUST NOT respond to the message.
If the AN receives a Provisioning message which updates an existing
multicast service profile, the AN MUST review the status of active
flows on all ports to which the updated profile has been assigned.
Similarly, if a Port Management message that assigns a new profile to
a given port, the AN MUST review all active flows on that port. In
either case, if any flow does not match an entry in the Grey list, it
MUST be terminated immediately.
6.2.4. Procedures For Delegated Bandwidth
6.2.4.1. Provisioning
The NAS SHOULD provision an initial amount of delegated multicast
bandwidth for each access line using the Port Management message
containing the Bandwidth-Allocation TLV.
If it fails to do so and a value has not been provisioned on the
AN by other means, the AN will be forced to request a bandwidth
allocation as soon as it receives a "join" request.
The NAS MAY at any time force an update of the amount of delegated
bandwidth by the same means.
6.2.4.2. Multicast Service Procedures
The delegated bandwidth capability assumes that IGMP/MLD requests are
terminated on the AN. When the AN receives a "join" request, it
checks whether it has sufficient remaining uncommitted multicast
bandwidth on the access line to accommodate the new multicast flow.
If not, it MAY send a request to the NAS for an increased allocation
of delegated bandwidth, using the Bandwidth Reallocation Request
Le Faucheur, et al. Expires September 9, 2010 [Page 55]
Internet-Draft ANCP Multicast Extensions March 2010
message. The NAS MUST return a Bandwidth Transfer message indicating
whether it has granted the request, and if so, what is the new amount
of delegated bandwidth.
If the AN has sufficient uncommitted multicast capacity to admit the
request, either originally or as the result of a successful request
to the NAS, it replicates the requested flow to the access line.
Otherwise it discards the request.
When the AN receives a "leave" request for an active flow, it ceases
replication.
The NAS or AN MAY at some point detect that their respective views of
the amount of delegated bandwidth are inconsistent. If so, they can
recover using procedures described in Section 4.5 and Section 4.6.
As a further aid to synchronization, either the NAS or the AN MAY
from time to time check the peer's view of the amount of delegated
bandwidth using the Delegated Bandwidth Query message.
The NAS or AN MAY at any time release bandwidth to the peer using an
autonomous Bandwidth Transfer message. The contents of this message
are described in Section 4.6.
6.3. Combinations of Multicast Capabilities
6.3.1. Combination of Conditional Access With White and Black Lists and
Conditional Access With Grey Lists
If conditional access with White and Black lists is combined with
conditional access with Grey lists, provisioning of the multicast
service profiles is as described in Section 6.2.2.1 except that
multicast service profiles will also include Grey lists. Admission
control is enabled independently on the AN for White lists by
including the White-list-CAC TLV in the Provisioning message and for
Grey lists by including the MRepCtl-CAC TLV in the Provisioning
message. The Bandwidth-Allocation TLV provisions an amount that
applies to both White- and Grey- listed flows if admission control is
enabled for both.
With regard to multicast service procedures, one point of difference
from the individual capabilities must be noted. This is an
interaction during the profile matching procedure. The AN MUST seek
the best match amongst multiple lists as described in
Section 6.2.2.2. However, if there are multiple matches of equal
precision, the order of priority is Black list first, Grey list
second, and White list last.
Once profile matching has been completed, processing of a "join"
Le Faucheur, et al. Expires September 9, 2010 [Page 56]
Internet-Draft ANCP Multicast Extensions March 2010
request is as described in Section 6.2.2.2 for White or Black listed
flows or Section 6.2.3.2 for Grey listed flows. Requests that do not
match any list SHOULD be discarded.
When the AN receives a "leave" request, it MUST terminate replication
of the flow to the access line. If the flow was Grey-listed, the AN
MUST then send a Multicast Admission Control message to the NAS
indicating the deletion. Thus the AN needs to retain the fact that
the flow was Grey-listed for the life of the flow.
If the AN receives a Provisioning message which updates an existing
multicast service profile, the AN MUST review the status of active
flows on all ports to which the updated profile is currently
assigned. Similarly, if a Port Management message assigns a new
multicast service profile to a given port, the AN MUST review all
active flows on that port. If any flow has its most specific match
in a Black list entry, it MUST be terminated immediately. If any of
the remaining flows do not match an entry in the White or Grey list,
they MUST also be terminated immediately. Finally, if any remaining
flows were originally admitted because they were White-listed, but
after the change they are Grey-listed, the AN MUST generate a
Multicast Flow Query response message autonomously as if it were
responding to a Multicast Flow Query request, listing all such flows.
These flows MUST be allowed to continue until the NAS or the
subscriber terminates them. Flows with their most specific match in
the White list MUST be allowed to continue.
The autonomously-generated Multicast Flow Query response message MUST
be formatted as if it were a successful response to a request
containing no Target and no Multicast-Flow TLV, as described in
Section 4.9.2, with the exception that the Transaction-Id MUST be set
to all zeroes.
6.3.2. Combination of Conditional Access With Delegated Bandwidth
The provisioning and bandwidth management procedures of Section 6.2.4
apply in addition to the procedures in Section 6.2.2, Section 6.2.3,
or Section 6.3.1 as applicable. Admission control follows the rules
for conditional access in terms of matching flows against White and
Black and/or Grey lists and performing or not performing bandwidth
checks at the AN, but the amount of bandwidth used by the AN to
perform admission control is negotiable as described in
Section 6.2.4.2.
6.3.3. Combination of NAS-Initiated Replication with Other Capabilities
NAS-initiated replication can coexist with the other capabilities,
but some means must exist to prevent double replication of flows.
Le Faucheur, et al. Expires September 9, 2010 [Page 57]
Internet-Draft ANCP Multicast Extensions March 2010
The simplest way to do this is to terminate all IGMP/MLD requests on
the AN, so that NAS-initiated replication is stimulated only by
signalling through other channels. Other arrangements are possible,
but need not be discussed here.
Assuming the necessary separation of responsibilities, the only point
of interaction between NAS-initiated replication and the other
multicast capabilities is in the area of admission control.
Specifically, inclusion of the MRepCtl-CAC TLV in a Provisioning
message and the Bandwidth-Allocation TLV in a Port Management message
enables admission control by the AN for flows added by Multicast
Replication Control messages, regardless of whether they are part of
NAS-initiated replication or Grey list multicast service processing.
Conversely, non inclusion of the MRepCtl-CAC TLV in Provisioning
messages to the AN enables admission control by the NAS for flows
added by Multicast Replication Control messages, regardless of
whether they are part of NAS- initiated replication or Grey list
multicast service processing. Admission Control for white flows can
also be enabled independently on the AN by inclusion by the NAS of
the White-List-CAC TLV in the Provisioning message.
Le Faucheur, et al. Expires September 9, 2010 [Page 58]
Internet-Draft ANCP Multicast Extensions March 2010
7. Security Considerations
The security considerations of ANCP are discussed in
[I-D.ietf-ancp-protocol] and in [I-D.ietf-ancp-security-threats].
[Probably need to say more, but will do so later.]
Le Faucheur, et al. Expires September 9, 2010 [Page 59]
Internet-Draft ANCP Multicast Extensions March 2010
8. IANA Considerations
This document defines the following additional values within the
GSMPv3 Message Type Name Space registry, under the new heading
"Multicast Extensions To ANCP/GSMPv3":
+---------------------------+---------------+--------+--------------+
| Message Name | Message | Status | Reference |
| | Number | | |
+---------------------------+---------------+--------+--------------+
| Multicast Replication | 144 | | This |
| Control | | | document |
| | | | |
| Multicast Admission | 145 | | This |
| Control | | | document |
| | | | |
| Bandwidth Reallocation | 146 | | This |
| Request | | | document |
| | | | |
| Bandwidth Transfer | 147 | | This |
| | | | document |
| | | | |
| Delegated Bandwidth Query | 148 | | This |
| | | | document |
| | | | |
| Multicast Flow Query | 149 | | This |
| | | | document |
+---------------------------+---------------+--------+--------------+
This document defines the following additional values for the GSMPv3
Failure Response Message Name Space registry:
+-------+--------------------------------------------+--------------+
| Value | Failure Response Message Name | Reference |
+-------+--------------------------------------------+--------------+
| 100 | Command error. | This |
| | | document |
| | | |
| 101 | Bad flow address. | This |
| | | document |
| | | |
| 102 | Multicast flow does not exist. | This |
| | | document |
| | | |
| 103 | Invalid preferred bandwidth amount. | This |
| | | document |
| | | |
Le Faucheur, et al. Expires September 9, 2010 [Page 60]
Internet-Draft ANCP Multicast Extensions March 2010
| 104 | Inconsistent views of delegated bandwidth | This |
| | amount. | document |
| | | |
| 105 | Bandwidth request conflict. | This |
| | | document |
+-------+--------------------------------------------+--------------+
This document defines the following additional values within the ANCP
TLV Type Registry:
+--------------------------------+-----------+---------------+
| TLV Name | Type Code | Reference |
+--------------------------------+-----------+---------------+
| Multicast-Service-Profile | 0x13 | This document |
| | | |
| Bandwidth-Allocation | 0x15 | This document |
| | | |
| Bandwidth-Request | 0x16 | This document |
| | | |
| Multicast-Service-Profile-Name | 0x18 | This document |
| | | |
| Multicast-Flow | 0x19 | This document |
| | | |
| List-Action | 0x21 | This document |
| | | |
| Sequence-Number | 0x22 | This document |
| | | |
| White-List-CAC | 0x24 | This document |
| | | |
| MRepCtl-CAC | 0x25 | This document |
| | | |
| Request-Source-IP | 0x92 | This document |
| | | |
| Request-Source-MAC | 0x93 | This document |
+--------------------------------+-----------+---------------+
This document defines the following additional values for the ANCP
Command Code registry:
Le Faucheur, et al. Expires September 9, 2010 [Page 61]
Internet-Draft ANCP Multicast Extensions March 2010
+-------------------------------------+----------------+------------+
| Command Code Directive Name | Command Code | Reference |
| | Value | |
+-------------------------------------+----------------+------------+
| Add | 0x01 | This |
| | | document |
| | | |
| Delete | 0x02 | This |
| | | document |
| | | |
| Delete All | 0x03 | This |
| | | document |
| | | |
| Admission Control Reject | 0x04 | This |
| | | document |
| | | |
| Conditional Access Reject | 0x05 | This |
| | | document |
| | | |
| Admission Control and Conditional | 0x06 | This |
| Access Reject | | document |
+-------------------------------------+----------------+------------+
This document defines the following additional values for the ANCP
Capability registry:
+-----------------------------------+------------------+------------+
| Capability Type Name | Capability Type | Reference |
| | Code | |
+-----------------------------------+------------------+------------+
| NAS-initiated replication | 0x5 | This |
| | | document |
| | | |
| Conditional access with white and | 0x6 | This |
| black lists | | document |
| | | |
| Conditional access with grey | 0x7 | This |
| lists | | document |
| | | |
| Bandwidth delegation | 0x8 | This |
| | | document |
+-----------------------------------+------------------+------------+
Le Faucheur, et al. Expires September 9, 2010 [Page 62]
Internet-Draft ANCP Multicast Extensions March 2010
9. Acknowledgements
The authors would like to acknowledge Wojciech Dec for providing
useful input to this document, Robert Rennison for his help in
shaping the definition of the Multicast-Service-Profile TLV, Shridhar
Rao for his comments and suggestions and Aniruddha A for his proposal
that formed the base of the Multicast Flow Reporting solution.
Philippe Champagne, Sanjay Wadhwa and Stefaan De Cnodder provided
substantial contributions on the solution for the NAS initiated
multicast control use case.
Le Faucheur, et al. Expires September 9, 2010 [Page 63]
Internet-Draft ANCP Multicast Extensions March 2010
10. References
10.1. Normative References
[I-D.ietf-ancp-framework]
Ooghe, S., Voigt, N., Platnic, M., Haag, T., and S.
Wadhwa, "Framework and Requirements for an Access Node
Control Mechanism in Broadband Multi-Service Networks",
draft-ietf-ancp-framework-13 (work in progress),
February 2010.
[I-D.ietf-ancp-protocol]
Wadhwa, S., Moisand, J., Subramanian, S., Haag, T., Voigt,
N., and R. Maglione, "Protocol for Access Node Control
Mechanism in Broadband Networks",
draft-ietf-ancp-protocol-09 (work in progress),
February 2010.
[IEEE48] IEEE, "http://standards.ieee.org/regauth/oui/tutorials/
EUI48.html", 2010.
[IEEE64] IEEE, "http://standards.ieee.org/regauth/oui/tutorials/
EUI64.html", 2010.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast
Listener Discovery (MLD) for IPv6", RFC 2710,
October 1999.
[RFC3292] Doria, A., Hellstrand, F., Sundell, K., and T. Worster,
"General Switch Management Protocol (GSMP) V3", RFC 3292,
June 2002.
[RFC3376] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A.
Thyagarajan, "Internet Group Management Protocol, Version
3", RFC 3376, October 2002.
[RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
10.2. Informative References
[I-D.ietf-ancp-security-threats]
Moustafa, H., Tschofenig, H., and S. Cnodder, "Security
Threats and Security Requirements for the Access Node
Control Protocol (ANCP)",
Le Faucheur, et al. Expires September 9, 2010 [Page 64]
Internet-Draft ANCP Multicast Extensions March 2010
draft-ietf-ancp-security-threats-08 (work in progress),
July 2009.
[I-D.morin-mboned-igmpmld-error-feedback]
Morin, T. and B. Haberman, "IGMP/MLD Error Feedback",
draft-morin-mboned-igmpmld-error-feedback-02 (work in
progress), November 2008.
[PIMreg] IANA, "http://www.iana.org/assignments/pim-parameters/
pim-parameters.xhtml", 2005.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601, August 2006.
[RFC5384] Boers, A., Wijnands, I., and E. Rosen, "The Protocol
Independent Multicast (PIM) Join Attribute Format",
RFC 5384, November 2008.
Le Faucheur, et al. Expires September 9, 2010 [Page 65]
Internet-Draft ANCP Multicast Extensions March 2010
Appendix A. Example of Messages and Message Flows
This appendix provides an example in which most of the possible
message flows for multicast control are illustrated. This appendix
is for informational purposes only. In case of discrepancy with text
of the body of this document, the text in the body of the document is
to be considered as the normative text.
Assume the following, for a given access port:
o The basic subscribed service is white-listed. The AN will be
responsible for admission control for this service.
o Some premium services are available, but requests for these
services must be referred to the policy server for proper credit
processing. For this reason they are grey-listed. The NAS will
be responsible for admission control for these services.
o The subscriber has asked that certain services be blocked so that
his children cannot view them. These services are black-listed.
o All of the above services are Source-Specific Multicast (SSM). In
addition, by means which bypass the AN, the subscriber can signal
intent to join an on-line game service which is Any-Source
Multicast (ASM). The NAS is responsible for admission control for
this service.
o Bandwidth delegation is in effect to share video bandwidth between
the AN and the NAS.
The stated conditions require the use of all four of the capabilities
specified in this memo.
A.1. Provisioning Phase
Assume that capability negotiation has been completed between the AN
and NAS and that the set of negotiated capabilities includes the
following four multicast capabilities: NAS-initiated replication,
conditional access with white and black list, conditional access with
grey list, and bandwidth delegation. At this point, the NAS can
provision the service profiles on the AN and enable admission control
at the AN for white-listed flows. To do this, the NAS sends the AN a
Provisioning message containing this information. An example message
providing the profile for our assumed subscriber is shown in
Figure 17. The message has the following contents:
o Message type is 93.
Le Faucheur, et al. Expires September 9, 2010 [Page 66]
Internet-Draft ANCP Multicast Extensions March 2010
o The Result and Code fields in the header are set to zeroes, as
specified in the ANCP base protocol document.
o A Transaction identifier is assigned by the NAS.
o The Multicast-Service-Profile TLV (of which typically there would
be multiple instances) contains a Multicast-Service-Profile-Name
TLV (with a length of 20 octets assumed for the example) and three
List-Action TLVs, one each for the White, Grey, and Black lists
within the profile. The White list flows come in two sets of
group addresses: 233.252.0.0/29, coming from a server at
192.0.2.15, and 233.252.0.32/29, coming from a server at
192.0.2.16. The Grey listed flows are in the band
233.252.0.64/29, coming from a server at 192.0.2.21. Finally, the
Black list flows are two individual flows that happen to overlap
with the Grey list band: 233.252.0.65, and 233.252.0.69, also with
source 192.0.2.21.
o The White-List-CAC TLV indicates that the AN does admission
control on White-listed flows.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 132 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type = 93 | 0x00 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 132 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| M-Serv-Prof TLV Type = 0x13 | TLV Length = 112 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| M-S-Prof-Name TLV Type = 0x18 | Embedded TLV Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast service profile name |
~ = "Cust 0127-53681-0003" ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List-Action TLV Type = 0x21 | Embedded TLV Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Oper = 0x01 |Lst Typ = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Family = 0x01 | List Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| G Preflen = 29| S Preflen = 32| Group prefix = |
Le Faucheur, et al. Expires September 9, 2010 [Page 67]
Internet-Draft ANCP Multicast Extensions March 2010
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 233.252.0.0 | Source prefix = |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.15 | G Preflen = 29| S Preflen = 32|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group prefix = 233.252.0.32 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source prefix = 192.0.2.15 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List-Action TLV Type = 0x21 | Embedded TLV Length = 18 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Oper = 0x01 |Lst Typ = 0x03 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Family = 0x01 | List Length = 10 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| G Preflen = 29| S Preflen = 32| Group prefix = /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ 233.252.0.64 | Source prefix = /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ 192.0.2.21 | Padding = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List-Action TLV Type = 0x21 | Embedded TLV Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Oper = 0x01 |Lst Typ = 0x02 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Family = 0x01 | List Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| G Preflen = 32| S Preflen = 32| Group prefix = /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ 233.252.0.65 | Source prefix = /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ 192.0.2.21 | G Preflen = 32| S Preflen = 32|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group prefix = 233.252.0.69 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source prefix = 192.0.2.21 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|White-List-CAC TLV Type = 0x24 | TLV Length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
TLV lengths are given in decimal for easier understanding. Note that
the padding after the middle List-Action TLV is counted as part of
length of the Multicast-Service-Profile TLV, but is not included in
the length of that List-Action TLV. Note also that the Length field
in the message header, unlike those in the TLVs, includes the message
header itself, as required by [RFC3292]. Finally, note that the
Provisioning message does not include a MRepCtl-CAC TLV since in our
example admission control for Grey listed flows and for NAS-initiated
Le Faucheur, et al. Expires September 9, 2010 [Page 68]
Internet-Draft ANCP Multicast Extensions March 2010
replication is performed by the NAS.
Figure 17: Example Provisioning Message
As soon as the AN port comes up, the AN sends an ANCP PORT_UP message
to the NAS specifying the Access Loop Circuit ID. The NAS replies
with an ANCP Port Management message that, together with the other
parameters, includes the multicast service profile name to be
associated to that port along with the initial amount of delegated
bandwidth. The corresponding message flow is illustrated in
Figure 18.
+----------+ +---------+ +-----+ +-----+
|Subscriber| | Home | | AN | | NAS |
+----------+ | Gateway | +-----+ +-----+
| +---------+ | |
| | | |
| | | |
| | DSL Synch. | |
| |--------------------->| |
| | |(M1)PORT_UP(Port ID) |
| | |-------------------->|
| | | (*)
| | |(M2) PORT_MNGT |
| | | (Port ID, |
| | |Mcast S Profile Name,|
| | |Bandwidth Allocation)|
| | |<--------------------|
(*) The NAS may optionally seek direction from an external
Autorization/Policy Server
Figure 18: Configuring an AN Port With Multicast Service Profile ID
and Delegated Bandwidth amount
The Port Management message will typically contain other TLVs but our
example (Figure 19) just shows the Target, Multicast-Service-Profile-
Name, and Bandwidth-Allocation TLVs. The Target TLV identifies the
subscriber line, the Multicast-Service-Profile-Name TLV is identical
to the one contained in the Provisioning message, and the Bandwidth-
Allocation TLV provides just enough bandwidth (2000 kbits/s) for one
channel to start with.
The following fields in the Port Management message header are shown
with specific values either as directed by the base protocol document
or for the sake of our example:
Le Faucheur, et al. Expires September 9, 2010 [Page 69]
Internet-Draft ANCP Multicast Extensions March 2010
o Message Type is 32.
o Result is set to Nack (0x01) for this example.
o Code is 0x000.
o Port is set to 0.
o Event Sequence Number, the R flag and the other bits marked x,
Duration, the Event Flags, and the Flow Control Flags are all
irrelevant for this function and are set to 0.
o Function is set to 0x8, "Configure Connection Service Data".
o X-Function is set to 0.
o Tech Type is 0x05 (DSL).
o Block lengths are calculated assuming a Circuit-Id length of 4 in
our example. Recall that the example Multicast-Service-Profile-
Name TLV length is 20.
Le Faucheur, et al. Expires September 9, 2010 [Page 70]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 84 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type = 32 | 0x01 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 84 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Port = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Port Session Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Event Sequence Number = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|R|x|x|x|x|x|x|x| Duration = 0 | Function = 0x8| X-Function = 0|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Event Flags | Flow Control Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|x|x|x|x|x|x|x|x| Msg Type = 32 |Tech Type=0x05 | Blk Len = 56 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| # of TLVs = 3 | Extension Block length = 44 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Target TLV Type = 0x1000 | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| M-S-Prof-Name TLV Type = 0x18 | TLV Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast service profile name |
~ = "Cust 0127-53681-0003" ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BW Alloc TLV Type = 0x15 | TLV Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Bandwidth value = 0x000007D0 (2000 kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 19: Example Port Management Message
Le Faucheur, et al. Expires September 9, 2010 [Page 71]
Internet-Draft ANCP Multicast Extensions March 2010
A.2. Handling a Grey-Listed Flow
Suppose now that the subscriber chooses to watch the premium channel
characterized by source 192.0.2.21, group 233.252.0.67. Upon
receiving the Join request, the AN matches it against the multicast
service profile for the port and determines that it is a Grey-listed
flow. Figure 20 illustrates the resulting ANCP message flow for the
case of a simple join and leave, when admission control for Grey-
listed flows is not activated on the AN. To start the flow, the AN
sends a Multicast Admission Control request (M1) to the NAS. The NAS
decides whether flow can be admitted, applying both policy and
bandwidth criteria. It returns its decision (positive in this
example) in a Multicast Replication Control message (M2). Later,
when the subscriber leaves the flow, the AN informs the NAS by
sending another Multicast Admission Control message.
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<---------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | Multicast |
| Join(Grey-Fl) | Admission |
|-----------+---------->| Control (M1) |
| | |------------------>|
| | | | (NAS performs
| | | Multicast | admission
| | | Replication (*) control)
| | | Control (M2) |
| Mcast Grey Flow |<------------------|
|<======================+ |
| | | |
~ ~ ~ ~
| | | Multicast |
| Leave(Grey-Fl) | Admission |
|-----------+---------->| Control (M3) |
| | |------------------>|
| | | |
Grey-Fl : Multicast Flow matching an entry in Grey List
(*) The NAS may optionally seek direction from an external
Authorization/Policy Server
Figure 20: Successful Join/Leave Operations, Grey-Listed Flow
The Multicast Admission Control message M1 contains:
Le Faucheur, et al. Expires September 9, 2010 [Page 72]
Internet-Draft ANCP Multicast Extensions March 2010
o an ANCP Header with:
* Message-Type = 145 - Multicast Admission Control;
* Result= 0x0 (Ignore);
* Transaction-ID = Transaction-ID maintained by AN;
o a Target TLV identifying the AN Port
o a Command TLV containing:
* Command Code = Add (0x01);
* Accounting = 0;
* a Multicast-Flow embedded TLV indicating the SSM multicast flow
(Flow Type = 0x02) for which the AN received the IGMP Join:
IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01) Source
Address = 192.0.2.21;
* a Request-Source-IP embedded TLV containing the IGMP join
source IP (192.0.2.100).
The Multicast Admission Control message M1 is illustrated below:
Le Faucheur, et al. Expires September 9, 2010 [Page 73]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 98 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=145 | 0x0 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 98 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Command TLV Type = 0x11 | TLV Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x01 |Acctg = 0x00 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.0.67 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.21 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
| Req-Src-IP TLV Type = 0x92 | Embedded TLV length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Address = 192.0.2.100 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Multicast Admission Control Message Seeking To Add A Flow
The Multicast Replication Control message M2 contains:
o an ANCP Header with:
* Message Type = 144 - Multicast Replication Control;
* Result= 0x1 (NAck);
* Transaction-ID = Transaction-ID maintained by NAS;
Le Faucheur, et al. Expires September 9, 2010 [Page 74]
Internet-Draft ANCP Multicast Extensions March 2010
o a Target TLV identifying the AN Port;
o a Command TLV containing:
* Command Code = Add (0x01);
* Accounting = 1 (begin flow accounting), since in our example
the operator wants accounting on this flow.
* a Multicast-Flow embedded TLV indicating the SSM multicast flow
(Flow Type = 0x02) that the NAS is admitting for this access
port: IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01)
Source Address = 192.0.2.21.
The Multicast Admission Control message M2 is illustrated below.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 48 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=144 | 0x1 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 48 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Command TLV Type = 0x11 | TLV Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x01 | Acctg = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.0.67 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.21 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 21: Multicast Replication Control Message Admitting A Flow
Le Faucheur, et al. Expires September 9, 2010 [Page 75]
Internet-Draft ANCP Multicast Extensions March 2010
The Multicast Admission Control message M3 advising the NAS that the
flow has been terminated contains:
o an ANCP Header with:
* Message-Type = 145 - Multicast Admission Control
* Result= 0x0 (Ignore)
* Transaction-ID = Transaction-ID maintained by AN
o a Target TLV identifying the AN Port
o a Command TLV containing:
* a Command Code = Delete (0x02);
* Accounting = 0;
* a Multicast-Flow embedded TLV indicating the SSM multicast flow
(Flow Type = 0x02) for which the AN received the IGMP leave:
IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01) Source
Address = 192.0.2.21.
* a Request-Source-IP embedded TLV containing the IGMP leave
request source, IPv4 (0x01) address 192.0.2.100.
The Multicast Admission Control message M3 is illustrated below.
Le Faucheur, et al. Expires September 9, 2010 [Page 76]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=145 | 0x0 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Command TLV Type = 0x11 | TLV Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x02 |Acctg = 0x00 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.0.67 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.21 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Req-Src-IP TLV Type = 0x92 | Embedded TLV length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Address = 192.0.2.100 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Multicast Admission Control Message Signalling flow Termination
A.3. Handling White-Listed Flows
The NAS has enabled White list admission control on the AN, and the
bandwidth delegation capability has been negotiated. White listed
flows in themselves require no messages to the NAS, either upon
admission or upon termination, but the AN may request an increase in
the amount of delegated bandwidth if it needs the increase to admit a
flow.
Consider an example where the AN has already admitted one White-
listed flow, thereby using up the initially provisioned amount of
delegated bandwidth (2000 kbits/s). A request is received to join a
Le Faucheur, et al. Expires September 9, 2010 [Page 77]
Internet-Draft ANCP Multicast Extensions March 2010
new flow in the White list range. The AN chooses to send a Bandwidth
Reallocation Request message to the NAS, requesting that the
delegated bandwidth allocation be increased to 4000 kbits/s at a
minimum, and preferably to 6000 kbits/s.
In our example, the NAS is managing bandwidth tightly, as witnessed
by its minimal initial allocation of just enough for one flow. It is
willing to provide the minimum additional amount only, and therefore
returns a Bandwidth Transfer message where the delegated bandwidth
value is given as 4000 kbits/s. With this amount, the AN is able to
admit the second White-listed flow. The AN could send a similar
Bandwidth Transfer message back to the NAS bringing the delegated
bandwidth amount back down to 2000 kbits/s when one of the flows is
terminated, but this shows nothing new and is omitted.
As one more point of illustration, suppose that the NAS chooses to
audit the current amount of delegated bandwidth to ensure it is
synchronized with the AN. It sends a Delegated Bandwidth Query
request message to the AN, and receives a Delegated Bandwidth Query
response message with the current allocation as the AN sees it.
The complete message flow is shown in Figure 22.
Le Faucheur, et al. Expires September 9, 2010 [Page 78]
Internet-Draft ANCP Multicast Extensions March 2010
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<---------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | |
| Join(White-F1) | |
|-----------+---------->| |
| | |AN performs |
| Mcast White Flow 1 | admission control |
|<======================+ |
| | | |
| Join(White-F2) | |
|-----------+---------->|No bandwidth left |
| | | |
| | |Bandwidth |
| | | Reallocation Req |
| | |------------------>|(M1)
| | | |
| | | (*)
| | |Bandwidth Transfer |
| AN can now |<------------------|(M2)
| admit flow | |
| Mcast White Flow 2 | |
|<======================+ |
| | | |
~ ~ ~ ~
| | |Delegated Bandwidth|
| | | Query request |
| | |<------------------|(M3)
| | | |
| | |Delegated Bandwidth|
| | | Query response |
| | |------------------>|(M4)
| | | |
(*) The NAS may optionally seek direction from an external
Authorization/Policy Server
Figure 22: Successful Join/Leave Operations, Grey-Listed Flow
The Bandwidth Reallocation Request message (M1) is shown in
Figure 23. The contents require little explanation. The Message
Type for the Bandwidth Reallocation Request is 146. The Result field
is set to 0x0 (Ignore). Besides the Target, the message has one
other TLV, the Bandwidth-Request, with a TLV Type of 0x16. The TLV
contains Required Amount and Preferred Amount fields, set to 4000 and
6000 kbits/s respectively.
Le Faucheur, et al. Expires September 9, 2010 [Page 79]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 36 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=146 | 0x0 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 36 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Bandwidth-Req TLV Type = 0x16 | TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Required Amount = 0x00000FA0 (4000 kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Preferred Amount = 0x00001770 (6000 kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 23: Bandwidth Reallocation Request Message
The Bandwidth Transfer message (M2) is shown in Figure 24. Again,
the contents are easily understood. The Message Type for the
Bandwidth Transfer message is 147. The Result field is set to
Success (0x3). The message contains the Target TLV and the
Bandwidth-Allocation TLV. The latter has a TLV Type of 0x15 and
contains a Delegated Amount field, set to 4000 kbits/s.
Le Faucheur, et al. Expires September 9, 2010 [Page 80]
Internet-Draft ANCP Multicast Extensions March 2010
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 32 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=147 | 0x3 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 32 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|BW-Allocation TLV Type = 0x15 | TLV Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Delegated Amount = 0x00000FA0 (4000 kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 24: NAS Response, Bandwidth Transfer Message
The Delegated Bandwidth Query request message (M3) is shown in
Figure 25. The Message Type for the Delegated Bandwidth Query
request message is 148. The Result field is set to AckAll (0x2).
The message contains the Target TLV only.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 24 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=148 | 0x2 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 24 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 25: Delegated Bandwidth Query Request Message
Le Faucheur, et al. Expires September 9, 2010 [Page 81]
Internet-Draft ANCP Multicast Extensions March 2010
Finally, the Delegated Bandwidth Query response message (M4) is shown
in Figure 26. The Message Type for the Delegated Bandwidth Query
response message is 148. The Result field is set to Success (0x3).
The message contains the Target TLV and the Bandwidth-Allocation TLV
with the Delegated Amount field set to 4000 kbits/s.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 32 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=148 | 0x3 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier (copied from request) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 32 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|BW-Allocation TLV Type = 0x15 | TLV Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Delegated Amount = 0x00000FA0 (4000 kbits/s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 26: Delegated Bandwidth Query Response Message
A.4. Handling Of Black-Listed Join Requests
This section introduces no new messages, since requests for flows in
the Black list are simply ignored. The one thing to point out is the
overlap in our example between the set of flows in the Grey list and
the flows in the Black list. This does not create any ambiguity,
since not only does the Black list have priority for equally good
matches, but also the Black list entries are more specific (group
prefix lengths of 32 versus 29 in the Grey list) than the Grey list
flow prefixes.
A.5. Handling Of Requests To Join and Leave the On-Line Game
The final class of multicast control actions in our example allows
the subscriber to enter and leave the on-line game. As described at
the beginning of this example, the game uses Any Source Multicast
(ASM). Subscriber signalling bypasses the AN, going directly to the
NAS (e.g., through a web interface).
Le Faucheur, et al. Expires September 9, 2010 [Page 82]
Internet-Draft ANCP Multicast Extensions March 2010
When the subscriber requests to join the game, the NAS (after
applying policy and bandwidth checks) sends a Multicast Replication
Control message to the AN to enable the flow on the port concerned.
The AN knows not to apply admission control, since it has not
received an MRepCtl-CAC TLV in the Provisioning message. When the
subscriber leaves, the NAS sends another Multicast Replication
Control message to delete the flow. This message sequence is shown
in Figure 27.
It is possible that the NAS finds that there is not enough bandwidth
available to accommodate the subscriber's request. In this case, the
NAS could send a Bandwidth Reallocation Request message to the AN,
asking it to release some of the bandwidth delegated to it. This is
not shown in the present example, since the messages are the same as
those already presented with the exception that the Preferred Amount
in the request will be *less than* or equal to the Required amount,
rather than *greater than* or equal to it.
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<---------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | |
| Join game | |
|-----------+------------------------------>|
| | | Multicast | NAS performs
| | | Replication (*) admission
| | | Control (M1) | control
| Mcast Game Flow |<------------------|
|<=====================>+ |
| | | |
~ ~ ~ ~
| | | |
| Leave game | |
|-----------+------------------------------>|
| | | Multicast |
| | | Replication |
| | | Control (M2) |
| Mcast Game Flow |<------------------|
| discontinued | |
| | | |
(*) The NAS may optionally seek direction from an external
Authorization/Policy Server
Figure 27: NAS-Initiated Flows For On-Line Gaming
Multicast Replication Control message (M1) in Figure 28 looks like
Le Faucheur, et al. Expires September 9, 2010 [Page 83]
Internet-Draft ANCP Multicast Extensions March 2010
the message in Figure 21 with two exceptions. The first is that the
NAS has the option to set the Result field to AckAll (0x02) if it
needs positive reassurance that the flow has been enabled. This was
not done here to save having to depict a response differing only in
the Result field. The larger difference in this example is that the
flow description in the Multicast-Flow embedded TLV is that of an ASM
multicast group (Flow Type = 0x01) with IPv4 (0x01) group address
233.252.1.100.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length = 44 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type=144 | 0x1 | Code = 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length = 44 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access Loop Circuit ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Command TLV Type = 0x11 | TLV Length = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cmd Code=0x01 | Acctg = 0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x01 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.1.100 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
Figure 28: Enabling The Subscriber To Join An On-Line Game
Message M2 terminating the flow when the subscriber leaves the game
looks the same as the message in Figure 28 with two exceptions: the
Command Code becomes Delete (0x02), and Accounting is set to 0 to
turn off flow accounting. Of course, the Transaction Identifier
values will differ between the two messages.
Le Faucheur, et al. Expires September 9, 2010 [Page 84]
Internet-Draft ANCP Multicast Extensions March 2010
A.6. Example Flow For Multicast Flow Reporting
The example in this section is independent of the example in the
preceding sections.
Figure 29 illustrates a message flow in a case where the NAS queries
the AN about which multicast flows are active on port 10, on port 20
and on port 11 of the AN.
+----------+ +-------+ +-----+ ANCP +-----+
|Subscriber| | Home | | AN |<---------->| NAS |
+----------+ |Gateway| +-----+ +-----+
| +-------+ | |
| | | Multicast Flow |
| | | Query Request |
| | | (M1) |
| | |<------------------|
| | | |
| | | Multicast Flow |
| | | Query Response |
| | | (M2) |
| | |------------------>|
| | | |
| | | |
Figure 29: Per Port Multicast Flow Reporting
The Multicast Flow Query Request message (M1) is illustrated in
Figure 30. The Message Type is 149. The Result field is set to
AckAll (0x2). Three Target TLVs are present, identifying port 10,
port 20, and port 11 respectively.
Le Faucheur, et al. Expires September 9, 2010 [Page 85]
Internet-Draft ANCP Multicast Extensions March 2010
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type = 149|Rslt=2 | Code = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port10) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port20) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port11) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 30: Multicast Flow Query Request Message For Per-Port
Multicast Flow Reporting
The Multicast Flow Query Response message (M2) is illustrated in
Figure 31. It indicates that there is one active multicast flow
[(192.0.2.1, 233.252.2.4)] on port 10, no active multicast flow on
port 20 and two active multicast flows [(192.0.2.1, 233.252.2.4) and
(192.0.2.2, 233.252.2.10)] on port 11.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
Le Faucheur, et al. Expires September 9, 2010 [Page 86]
Internet-Draft ANCP Multicast Extensions March 2010
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (0x88-0C) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers | Sub | Msg Type = 149|Rslt=3 | Code = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID | Transaction Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I| SubMessage Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port10) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.2.4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port20) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x1000 (Target) | Target TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Access Loop Circuit ID (port11) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address = 233.252.2.4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.1 |
Le Faucheur, et al. Expires September 9, 2010 [Page 87]
Internet-Draft ANCP Multicast Extensions March 2010
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
|Multicast-Flow TLV Type = 0x19 | Embedded TLV Length = 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Flow Type=0x02 |Addr Fam =0x01 | Reserved = 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multicast Group Address: 233.252.2.10 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Unicast Source Address = 192.0.2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
Figure 31: Multicast Flow Query Response message for per-port
Mulicast Flow Reporting
Le Faucheur, et al. Expires September 9, 2010 [Page 88]
Internet-Draft ANCP Multicast Extensions March 2010
Authors' Addresses
Francois Le Faucheur
Cisco Systems
Greenside, 400 Avenue de Roumanille
Sophia Antipolis 06410
France
Phone: +33 4 97 23 26 19
Email: flefauch@cisco.com
Roberta Maglione
Telecom Italia
Via Reiss Romoli 274
Torino 10148
Italy
Phone:
Email: roberta.maglione@telecomitalia.it
Tom Taylor
Huawei Technologies
1852 Lorraine Ave
Ottawa, Ontario K1H 6Z8
Canada
Phone: +1 613 680 2675
Email: tom111.taylor@bell.net
Le Faucheur, et al. Expires September 9, 2010 [Page 89]