AVT T. Turletti
Internet-Draft MIT
Expires: May 1, 2004 C. Huitema
Microsoft
R. Even
Polycom
November 2003
RTP Payload Format for H.261 Video Streams
draft-ietf-avt-rfc2032-bis-00.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at http://
www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on May 1, 2004.
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Abstract
This memo describes a scheme to packetize an H.261 video stream for
transport using the Real-time Transport Protocol, RTP, with any of
the underlying protocols that carry RTP.
This specification is a product of the Audio/Video Transport working
group within the Internet Engineering Task Force. Comments are
solicited and should be addressed to the working group's mailing list
and/or the authors.
Turletti, et al. Expires May 1, 2004 [Page 1]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Structure of the packet stream . . . . . . . . . . . . . . . 4
2.1 Overview of the ITU-T recommendation H.261 . . . . . . . . . 4
2.2 Considerations for packetization . . . . . . . . . . . . . . 4
3. Specification of the packetization scheme . . . . . . . . . 6
3.1 Usage of RTP . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Recommendations for operation with hardware codecs . . . . . 8
4. Packet loss issues . . . . . . . . . . . . . . . . . . . . . 10
4.1 Use of optional H.261-specific control packets . . . . . . . 10
4.2 H.261 control packets definition . . . . . . . . . . . . . . 11
4.2.1 Full INTRA-frame Request (FIR) packet . . . . . . . . . . . 11
4.2.2 Negative Acknowledgements (NACK) packet . . . . . . . . . . 12
5. Payload Format Parameters . . . . . . . . . . . . . . . . . 13
5.1 IANA Considerations . . . . . . . . . . . . . . . . . . . . 13
5.1.1 Registration of MIME media type video/H261 . . . . . . . . . 13
5.2 SDP Parameters . . . . . . . . . . . . . . . . . . . . . . . 14
6. Security Considerations . . . . . . . . . . . . . . . . . . 15
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 16
8. Requirements notation . . . . . . . . . . . . . . . . . . . 17
9. changes from RFC 2032> . . . . . . . . . . . . . . . . . . . 18
Normative References . . . . . . . . . . . . . . . . . . . . 19
Informative References . . . . . . . . . . . . . . . . . . . 20
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . 20
Intellectual Property and Copyright Statements . . . . . . . 22
Turletti, et al. Expires May 1, 2004 [Page 2]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
1. Introduction
The ITU-T recommendation H.261[H261] specifies the encoding used by
ITU-T compliant video-conference codecs. Although these encoding were
originally specified for fixed data rate ISDN circuits, experiments
[INRIA],[MICE] have shown that they can also be used over
packet-switched networks such as the Internet.
The purpose of this memo is to specify the RTP payload format for
encapsulating H.261 video streams in RTP[RFC3550].
Turletti, et al. Expires May 1, 2004 [Page 3]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
2. Structure of the packet stream
2.1 Overview of the ITU-T recommendation H.261
The H.261 coding is organized as a hierarchy of groupings. The video
stream is composed of a sequence of images, or frames, which are
themselves organized as a set of Groups of Blocks (GOB). Note that
H.261 "pictures" are referred as "frames" in this document. Each GOB
holds a set of 3 lines of 11 macro blocks (MB). Each MB carries
information on a group of 16x16 pixels: luminance information is
specified for 4 blocks of 8x8 pixels, while chrominance information
is given by two "red" and "blue" color difference components at a
resolution of only 8x8 pixels. These components and the codes
representing their sampled values are as defined in the ITU-R
Recommendation 601 [BT601].
This grouping is used to specify information at each level of the
hierarchy:
- At the frame level, one specifies information such as the delay
from the previous frame, the image format, and various indicators.
- At the GOB level, one specifies the GOB number and the default
quantifier that will be used for the MBs.
- At the MB level, one specifies which blocks are present and
which did not change, and optionally a quantifier and motion vectors.
Blocks which have changed are encoded by computing the discrete
cosine transform (DCT) of their coefficients, which are then
quantized and Huffman encoded (Variable Length Codes).
The H.261 Huffman encoding includes a special "GOB start" pattern,
composed of 15 zeroes followed by a single 1, that cannot be imitated
by any other code words. This pattern is included at the beginning of
each GOB header (and also at the beginning of each frame header) to
mark the separation between two GOBs, and is in fact used as an
indicator that the current GOB is terminated. The encoding also
includes a stuffing pattern, composed of seven zeroes followed by
four ones; that stuffing pattern can only be entered between the
encoding of MBs, or just before the GOB separator.
2.2 Considerations for packetization
H.261 codecs designed for operation over ISDN circuits produce a bit
stream composed of several levels of encoding specified by H.261 and
companion recommendations. The bits resulting from the Huffman
encoding are arranged in 512-bit frames, containing 2 bits of
Turletti, et al. Expires May 1, 2004 [Page 4]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
synchronization, 492 bits of data and 18 bits of error correcting
code. The 512-bit frames are then interlaced with an audio stream
and transmitted over px64 kbps circuits according to specification
H.221 [H221].
When transmitting over the Internet, we will directly consider the
output of the Huffman encoding. All the bits produced by the Huffman
encoding stage will be included in the packet. We will not carry the
512-bit frames, as protection against bit errors can be obtained by
other means. Similarly, we will not attempt to multiplex audio and
video signals in the same packets, as UDP and RTP provide a much more
efficient way to achieve multiplexing.
Directly transmitting the result of the Huffman encoding over an
unreliable stream of UDP datagrams would, however, have poor error
resistance characteristics. The result of the hierarchical structure
of H.261 bit stream is that one needs to receive the information
present in the frame header to decode the GOBs, as well as the
information present in the GOB header to decode the MBs. Without
precautions, this would mean that one has to receive all the packets
that carry an image in order to properly decode its components.
If each image could be carried in a single packet, this requirement
would not create a problem. However, a video image or even one GOB by
itself can sometimes be too large to fit in a single packet.
Therefore, the MB is taken as the unit of fragmentation. Packets
must start and end on a MB boundary, i.e. a MB cannot be split across
multiple packets. Multiple MBs may be carried in a single packet
when they will fit within the maximal packet size allowed. This
practice is recommended to reduce the packet send rate and packet
overhead.
To allow each packet to be processed independently for efficient
resynchronization in the presence of packet losses, some state
information from the frame header and GOB header is carried with each
packet to allow the MBs in that packet to be decoded. This state
information includes the GOB number in effect at the start of the
packet, the macroblock address predictor (i.e. the last MBA encoded
in the previous packet), the quantizer value in effect prior to the
start of this packet (GQUANT, MQUANT or zero in case of a beginning
of GOB) and the reference motion vector data (MVD) for computing the
true MVDs contained within this packet. The bit stream cannot be
fragmented between a GOB header and MB 1 of that GOB.
Moreover, since the compressed MB may not fill an integer number of
octets, the data header contains two three-bit integers, SBIT and
EBIT, to indicate the number of unused bits in the first and last
octets of the H.261 data, respectively.
Turletti, et al. Expires May 1, 2004 [Page 5]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
3. Specification of the packetization scheme
3.1 Usage of RTP
The H.261 information is carried as payload data within the RTP
protocol. The following fields of the RTP header are specified:
- The payload type should specify H.261 payload format (see the
companion RTP profile document RFC 1890).
- The RTP timestamp encodes the sampling instant of the first
video image contained in the RTP data packet. If a video image
occupies more than one packet, the timestamp will be the same on all
of those packets. Packets from different video images must have
different timestamps so that frames may be distinguished by the
timestamp. For H.261 video streams, the RTP timestamp is based on a
90kHz clock. This clock rate is a multiple of the natural H.261 frame
rate (i.e. 30000/1001 or approx. 29.97 Hz). That way, for each frame
time, the clock is just incremented by the multiple and this removes
inaccuracy in calculating the timestamp. Furthermore, the initial
value of the timestamp is random (unpredictable) to make
known-plaintext attacks on encryption more difficult, see RTP
[RFC3550]. Note that if multiple frames are encoded in a packet (e.g.
when there are very little changes between two images), it is
necessary to calculate display times for the frames after the first
using the timing information in the H.261 frame header. This is
required because the RTP timestamp only gives the display time of the
first frame in the packet.
- The marker bit of the RTP header is set to one in the last
packet of a video frame, and otherwise, must be zero. Thus, it is not
necessary to wait for a following packet (which contains the start
code that terminates the current frame) to detect that a new frame
should be displayed.
The H.261 data will follow the RTP header, as in:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. RTP header .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| H.261 header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| H.261 stream ... .
Turletti, et al. Expires May 1, 2004 [Page 6]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The H.261 header is defined as following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|SBIT |EBIT |I|V| GOBN | MBAP | QUANT | HMVD | VMVD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The fields in the H.261 header have the following meanings:
Start bit position (SBIT): 3 bits
Number of most significant bits that should be ignored in the first
data octet.
End bit position (EBIT): 3 bits
Number of least significant bits that should be ignored in the last
data octet.
INTRA-frame encoded data (I): 1 bit
Set to 1 if this stream contains only INTRA-frame coded blocks. Set
to 0 if this stream may or may not contain INTRA-frame coded blocks.
The sense of this bit may not change during the course of the RTP
session.
Motion Vector flag (V): 1 bit
Set to 0 if motion vectors are not used in this stream. Set to 1 if
motion vectors may or may not be used in this stream. The sense of
this bit may not change during the course of the session.
GOB number (GOBN): 4 bits
Encodes the GOB number in effect at the start of the packet. Set to 0
if the packet begins with a GOB header.
Macroblock address predictor (MBAP): 5 bits
Encodes the macroblock address predictor (i.e. the last MBA encoded
in the previous packet). This predictor ranges from 0-32 (to predict
the valid MBAs 1-33), but because the bit stream cannot be fragmented
between a GOB header and MB 1, the predictor at the start of the
packet can never be 0. Therefore, the range is 1-32, which is biased
Turletti, et al. Expires May 1, 2004 [Page 7]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
by -1 to fit in 5 bits. For example, if MBAP is 0, the value of the
MBA predictor is 1. Set to 0 if the packet begins with a GOB header.
Quantizer (QUANT): 5 bits
Quantizer value (MQUANT or GQUANT) in effect prior to the start of
this packet. Set to 0 if the packet begins with a GOB header.
Horizontal motion vector data (HMVD): 5 bits
Reference horizontal motion vector data (MVD). Set to 0 if V flag is
0 or if the packet begins with a GOB header, or when the MTYPE of the
last MB encoded in the previous packet was not MC. HMVD is encoded as
a 2's complement number, and `10000' corresponding to the value -16
is forbidden (motion vector fields range from +/-15).
Vertical motion vector data (VMVD): 5 bits
Reference vertical motion vector data (MVD). Set to 0 if V flag is 0
or if the packet begins with a GOB header, or when the MTYPE of the
last MB encoded in the previous packet was not MC. VMVD is encoded as
a 2's complement number, and `10000' corresponding to the value -16
is forbidden (motion vector fields range from +/-15).
Note that the I and V flags are hint flags, i.e. they can be inferred
from the bit stream. They are included to allow decoders to make
optimizations that would not be possible if these hints were not
provided before bit stream was decoded. Therefore, these bits cannot
change for the duration of the stream. A conformant implementation
can always set V=1 and I=0.
3.2 Recommendations for operation with hardware codecs
Packetizers for hardware codecs can trivially figure out GOB
boundaries using the GOB-start pattern included in the H.261 data.
(Note that software encoders already know the boundaries.) The
cheapest packetization implementation is to packetize at the GOB
level all the GOBs that fit in a packet. But when a GOB is too
large, the packetizer has to parse it to do MB fragmentation. (Note
that only the Huffman encoding must be parsed and that it is not
necessary to fully decompress the stream, so this requires relatively
little processing; example implementations can be found in some
public H.261 codecs such as IVS [IVS] and VIC [VIC].) It is
recommended that MB level fragmentation be used when feasible in
order to obtain more efficient packetization. Using this
fragmentation scheme reduces the output packet rate and therefore
reduces the overhead.
Turletti, et al. Expires May 1, 2004 [Page 8]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
At the receiver, the data stream can be depacketized and directed to
a hardware codec's input. If the hardware decoder operates at a
fixed bit rate, synchronization may be maintained by inserting the
stuffing pattern between MBs (i.e., between packets) when the packet
arrival rate is slower than the bit rate.
Turletti, et al. Expires May 1, 2004 [Page 9]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
4. Packet loss issues
On the Internet, most packet losses are due to network congestion
rather than transmission errors. Using UDP, no mechanism is available
at the sender to know if a packet has been successfully received. It
is up to the application, i.e. coder and decoder, to handle the
packet loss. Each RTP packet includes a a sequence number field which
can be used to detect packet loss.
H.261 uses the temporal redundancy of video to perform compression.
This differential coding (or INTER-frame coding) is sensitive to
packet loss. After a packet loss, parts of the image may remain
corrupt until all corresponding MBs have been encoded in INTRA-frame
mode (i.e. encoded independently of past frames). There are several
ways to mitigate packet loss:
(1) One way is to use only INTRA-frame encoding and MB level
conditional replenishment. That is, only MBs that change (beyond some
threshold) are transmitted.
(2) Another way is to adjust the INTRA-frame encoding refreshment
rate according to the packet loss observed by the receivers. The
H.261 recommendation specifies that a MB is INTRA-frame encoded at
least every 132 times it is transmitted. However, the INTRA-frame
refreshment rate can be raised in order to speed the recovery when
the measured loss rate is significant.
(3) The fastest way to repair a corrupted image is to request an
INTRA-frame coded image refreshment after a packet loss is detected.
One means to accomplish this is for the decoder to send to the coder
a list of packets lost. The coder can decide to encode every MB of
every GOB of the following video frame in INTRA-frame mode (i.e. Full
INTRA-frame encoded), or if the coder can deduce from the packet
sequence numbers which MBs were affected by the loss, it can save
bandwidth by sending only those MBs in INTRA-frame mode. This mode is
particularly efficient in point-to-point connection or when the
number of decoders is low. The next section specifies how the
refresh function may be implemented.
Note that the method (1) is currently implemented in the VIC
videoconferencing software [VIC]. Methods (2) and (3) are currently
implemented in the IVS videoconferencing software [IVS] .
4.1 Use of optional H.261-specific control packets
This specification defines two H.261-specific RTCP control packets,
"Full INTRA-frame Request" and "Negative Acknowledgement", described
in the next section. Their purpose is to speed up refreshment of the
Turletti, et al. Expires May 1, 2004 [Page 10]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
video in those situations where their use is feasible. Support of
these H.261-specific control packets by the H.261 sender is optional;
in particular, early experiments have shown that the usage of this
feature could have very negative effects when the number of sites is
very large. Thus, these control packets should be used with caution.
The H.261-specific control packets differ from normal RTCP packets in
that they are not transmitted to the normal RTCP destination
transport address for the RTP session (which is often a multicast
address). Instead, these control packets are sent directly via
unicast from the decoder to the coder. The destination port for
these control packets is the same port that the coder uses as a
source port for transmitting RTP (data) packets. Therefore, these
packets may be considered "reverse" control packets.
As a consequence, these control packets may only be used when no RTP
mixers or translators intervene in the path from the coder to the
decoder. If such intermediate systems do intervene, the address of
the coder would no longer be present as the network-level source
address in packets received by the decoder, and in fact, it might not
be possible for the decoder to send packets directly to the coder.
Some reliable multicast protocols use similar NACK control packets
transmitted over the normal multicast distribution channel, but they
typically use random delays to prevent a NACK implosion problem
[IEEE]. The goal of such protocols is to provide reliable multicast
packet delivery at the expense of delay, which is appropriate for
applications such as a shared whiteboard.
On the other hand, interactive video transmission is more sensitive
to delay and does not require full reliability. For video
applications it is more effective to send the NACK control packets as
soon as possible, i.e. as soon as a loss is detected, without adding
any random delays. In this case, multicasting the NACK control
packets would generate useless traffic between receivers since only
the coder will use them. But this method is only effective when the
number of receivers is small. e.g. in IVS [IVS] the H.261 specific
control packets are used only in point-to-point connections or in
point-to-multipoint connections when there are less than 10
participants in the conference.
4.2 H.261 control packets definition
4.2.1 Full INTRA-frame Request (FIR) packet
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
Turletti, et al. Expires May 1, 2004 [Page 11]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P| MBZ | PT=RTCP_FIR | length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SSRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This packet indicates that a receiver requires a full encoded image
in order to either start decoding with an entire image or to refresh
its image and speed the recovery after a burst of lost packets. The
receiver requests the source to force the next image in full "INTRA-
frame" coding mode, i.e. without using differential coding. The
various fields are defined in the RTP specification [RFC3550]. SSRC
is the synchronization source identifier for the sender of this
packet. The value of the packet type (PT) identifier is the constant
RTCP_FIR (192).
4.2.2 Negative Acknowledgements (NACK) packet
The format of the NACK packet is as follow:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P| MBZ | PT=RTCP_NACK | length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SSRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FSN | BLP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The various fields T, P, PT, length and SSRC are defined in the RTP
specification [RFC3550]. The value of the packet type (PT) identifier
is the constant RTCP_NACK (193). SSRC is the synchronization source
identifier for the sender of this packet.
The two remaining fields have the following meanings:
First Sequence Number (FSN): 16 bits
Identifies the first sequence number lost.
Bitmask of following lost packets (BLP): 16 bits
A bit is set to 1 if the corresponding packet has been lost, and set
to 0 otherwise. BLP is set to 0 only if no packet other than that
being NACKed (using the FSN field) has been lost. BLP is set to
0x00001 if the packet corresponding to the FSN and the following
packet have been lost, etc.
Turletti, et al. Expires May 1, 2004 [Page 12]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
5. Payload Format Parameters
This section updates the H.261 media type described in RFC3555
[RFC3555].
This section specifies optional parameters that MAY be used to select
optional features of the payload format. The parameters are
specified here as part of the MIME subtype registration for the
ITU-T H.261codec. A mapping of the parameters into the Session
Description Protocol (SDP) [RFC2327] is also provided for those
applications that use SDP. Multiple parameters SHOULD be expressed as
a MIME media type string, in the form of a space-separated list of
parameter=value pairs
5.1 IANA Considerations
This section describes the MIME types and names associated with this
payload format. The section registers the MIME types, as per
RFC2048[RFC2048]
5.1.1 Registration of MIME media type video/H261
MIME media type name: video
MIME subtype name: H261
Required parameters: None
Optional parameters:
CIF: Describes the maximum supported frame rate for CIF resolution.
permissible value are integer values 1 to 4 and it means that the
maximum rate is 29.97/ specified value
QCIF: Describes themaximum supported frame rate for QCIF resolution.
permissible value are integer values 1 to 4 and it means that the
maximum rate is 29.97/ specified value
D: specifies support for still image graphics according to H.261
annex D.
Encoding considerations:
This type is only defined for transfer via RTP [RFC3550]
Security considerations: See Section 6
Interoperability considerations: none
Turletti, et al. Expires May 1, 2004 [Page 13]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Published specification: RFC yyy
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person and email address to contact for further information :
Roni Evenr: roni.even@polycom.co.il
Intended usage: COMMON
>Author/Change controller:
Roni Even
5.2 SDP Parameters
The MIME media type video/H261 string is mapped to fields in the
Session Description Protocol (SDP) as follows:
o The media name in the "m=" line of SDP MUST be video.
o The encoding name in the "a=rtpmap" line of SDP MUST be H261 (the
MIME subtype).
o The clock rate in the "a=rtpmap" line MUST be 90000.
o The optional parameters "CIF", "QCIF" and "D" if any, SHALL be
included in the "a=fmtp" line of SDP. These parameters are expressed
as a MIME media type string, in the form of as a space separated
list of parameter=value pairs."
An example of media representation in SDP is as follows: (CIF at 15
frames per second, QCIF at 30 frames per second and annex D
m=video 49170/2 RTP/AVP 98
a=rtpmap:98 H261/90000
a=fmtp:98 CIF=2 QCIF=3 D
Turletti, et al. Expires May 1, 2004 [Page 14]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
6. Security Considerations
RTP packets using the payload format defined in this specification
are subject to the security considerations discussed in the RTP
specification. This implies that confidentiality of the media streams
is achieved by encryption. Because the data compression used with
this payload format is applied end-to-end, encryption may be
performed after compression so there is no conflict between the two
operations.
Turletti, et al. Expires May 1, 2004 [Page 15]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
7. Acknowledgements
This is to acknowledge the work done by Petri Koskelainen from Nokia
and Nermeen Ismail from Cisco who helped with drafting the text for
the new MIME types.
Turletti, et al. Expires May 1, 2004 [Page 16]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
8. Requirements notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119[RFC2119].
Turletti, et al. Expires May 1, 2004 [Page 17]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
9. changes from RFC 2032>
The changes from the RFC 2032 are:
1. The H.261 MIME type is now in the payload specification.
Added optional parameters to the H.261 MIME type
3. Editorial changes to be in line with RFC editing procedures
Turletti, et al. Expires May 1, 2004 [Page 18]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Normative References
[H261] International Telecommunications Union, "Video codec for
audiovisual services at p x 64 kbit/s", ITU Recommendation
H.261, March 1993.
[RFC2048] Freed, N., Klensin, J. and J. Postel, "Multipurpose
Internet Mail Extensions (MIME) Part Four: Registration
Procedures", BCP 13, RFC 2048, November 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2327] Handley, M. and V. Jacobson, "SDP: Session Description
Protocol", RFC 2327, April 1998.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R. and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", RFC 3550, July 2003.
[RFC3555] Casner, S. and P. Hoschka, "MIME Type Registration of RTP
Payload Formats", RFC 3555, July 2003.
Turletti, et al. Expires May 1, 2004 [Page 19]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Informative References
[BT601] International Telecommunications Union, "Studio encoding
parameters of digital television for standard 4:3 and
wide-screen 16:9 aspect ratios", ITU-R Recommendation
BT.601-5, October 1995.
[H221] International Telecommunications Union, "Frame structure for
a 64 to 1920 kbit/s channel in audiovisual teleservices",
ITU Recommendation H.221, May 1999.
[IEEE] Pingali, S., Towsley, D. and JF. Kurose, "A comparison of
sender-initiated and receiver-initiated reliable multicast
protocols", IEEE GLOBECOM 94, 1994.
[INRIA] Turletti, T., "H.261 software codec for videoconferencing
over the Internet", INRIA Research Report 1834, January
1993.
[IVS] Turletti, T., "INRIA Videoconferencing tool (IVS), available
by anonymous ftp from zenon.inria.fr in the "rodeo/ivs/
last_version" directory. See also URL http://www.inria.fr/
rodeo/ivs.html".
[MICE] Sasse, MA., Bilting, U., Schultz, CD. and T. Turletti,
"Remote Seminars through MultiMedia Conferencing:
Experiences from the MICE project", Proc. INET'94/JENC5,
Prague pp. 251/1-251/8, June !994.
[VIC] MacCanne, S., "VIC Videoconferencing tool, available by
anonymous ftp from ee.lbl.gov in the "conferencing/vic"
directory".
Authors' Addresses
Thierry Turletti
MIT
Christian Huitema
Microsoft
Turletti, et al. Expires May 1, 2004 [Page 20]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Roni Even
Polycom
94 Derech Em Hamoshavot
Petach Tikva 49130
Israel
EMail: roni.even@polycom.co.il
Turletti, et al. Expires May 1, 2004 [Page 21]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assignees.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
Turletti, et al. Expires May 1, 2004 [Page 22]
Internet-Draft RTP Payload Format for H.261 Video Streams November 2003
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Turletti, et al. Expires May 1, 2004 [Page 23]