AVTCORE WG                                                 M. Westerlund
Internet-Draft                                                  Ericsson
Updates: 3550, 3551 (if approved)                             C. Perkins
Intended status: Standards Track                   University of Glasgow
Expires: June 12, 2016                                         J. Lennox
                                                                   Vidyo
                                                       December 10, 2015


        Sending Multiple Types of Media in a Single RTP Session
             draft-ietf-avtcore-multi-media-rtp-session-12

Abstract

   This document specifies how an RTP session can contain RTP Streams
   with media from multiple media types such as audio, video, and text.
   This has been restricted by the RTP Specification, and thus this
   document updates RFC 3550 and RFC 3551 to enable this behaviour for
   applications that satisfy the applicability for using multiple media
   types in a single RTP session.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on June 12, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect



Westerlund, et al.        Expires June 12, 2016                 [Page 1]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Background and Motivation . . . . . . . . . . . . . . . . . .   3
   4.  Applicability . . . . . . . . . . . . . . . . . . . . . . . .   4
   5.  Using Multiple Media Types in a Single RTP Session  . . . . .   6
     5.1.  Allowing Multiple Media Types in an RTP Session . . . . .   6
     5.2.  Demultiplexing media types within an RTP session  . . . .   7
     5.3.  Per-SSRC Media Type Restrictions  . . . . . . . . . . . .   8
     5.4.  RTCP Considerations . . . . . . . . . . . . . . . . . . .   8
   6.  Extension Considerations  . . . . . . . . . . . . . . . . . .   9
     6.1.  RTP Retransmission Payload Format . . . . . . . . . . . .   9
     6.2.  RTP Payload Format for Generic FEC  . . . . . . . . . . .  10
     6.3.  RTP Payload Format for Redundant Audio  . . . . . . . . .  11
   7.  Signalling  . . . . . . . . . . . . . . . . . . . . . . . . .  12
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  12
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  13
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  13
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  13
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  13
     11.2.  Informative References . . . . . . . . . . . . . . . . .  14
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  15

1.  Introduction

   The Real-time Transport Protocol [RFC3550] was designed to use
   separate RTP sessions to transport different types of media.  This
   implies that different transport layer flows are used for different
   media streams.  For example, a video conferencing application might
   send audio and video traffic RTP flows on separate UDP ports.  With
   increased use of network address/port translation, firewalls, and
   other middleboxes it is, however, becoming difficult to establish
   multiple transport layer flows between endpoints.  Hence, there is
   pressure to reduce the number of concurrent transport flows used by
   RTP applications.

   This memo updates [RFC3550] and [RFC3551] to allow multiple media
   types to be sent in a single RTP session in certain cases, thereby
   reducing the number of transport layer flows that are needed.  It
   makes no changes to RTP behaviour when using multiple RTP streams
   containing media of the same type (e.g., multiple audio streams or
   multiple video streams) in a single RTP session.  However



Westerlund, et al.        Expires June 12, 2016                 [Page 2]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   [I-D.ietf-avtcore-rtp-multi-stream] provides important clarifications
   to RTP behaviour in that case.

   This memo is structured as follows.  Section 2 defines terminology.
   Section 3 further describes the background to, and motivation for,
   this memo and Section 4 describes the scenarios where this memo is
   applicable.  Section 5 discusses issues arising from the base RTP and
   RTCP specification when using multiple types of media in a single RTP
   session, while Section 6 considers the impact of RTP extensions.  We
   discuss signalling in Section 7.  Finally, security considerations
   are discussed in Section 8.

2.  Terminology

   The terms Encoded Stream, Endpoint, Media Source, RTP Session, and
   RTP Stream are used as defined in [RFC7656].  We also define the
   following terms:

   Media Type:  The general type of media data used by a real-time
      application.  The media type corresponds to the value used in the
      <media> field of an SDP m= line.  The media types defined at the
      time of this writing are "audio", "video", "text", "image",
      "application", and "message".  [RFC4566] [RFC6466]

   Quality of Service (QoS):  Network mechanisms that are intended to
      ensure that the packets within a flow or with a specific marking
      are transported with certain properties.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119].

3.  Background and Motivation

   RTP was designed to support multimedia sessions, containing multiple
   types of media sent simultaneously, by using multiple transport layer
   flows.  The existence of network address translators, firewalls, and
   other middleboxes complicates this, however, since a mechanism is
   needed to ensure that all the transport layer flows needed by the
   application can be established.  This has three consequences:

   1.  increased delay to establish a complete session, since each of
       the transport layer flows needs to be negotiated and established;

   2.  increased state and resource consumption in the middleboxes that
       can lead to unexpected behaviour when middlebox resource limits
       are reached; and



Westerlund, et al.        Expires June 12, 2016                 [Page 3]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   3.  increased risk that a subset of the transport layer flows will
       fail to be established, thus preventing the application from
       communicating.

   Using fewer transport layer flows can hence be seen to reduce the
   risk of communication failure, and can lead to improved reliability
   and performance.

   One of the benefits of using multiple transport layer flows is that
   it makes it easy to use network layer quality of service (QoS)
   mechanisms to give differentiated performance for different flows.
   However, we note that many RTP-using application don't use network
   QoS features, and don't expect or desire any separation in network
   treatment of their media packets, independent of whether they are
   audio, video or text.  When an application has no such desire, it
   doesn't need to provide a transport flow structure that simplifies
   flow based QoS.

   Given the above issues, it might seem appropriate for RTP-based
   applications to send all their media streams bundled into one RTP
   session, running over a single transport layer flow.  However, this
   is prohibited by the RTP specification, because the design of RTP
   makes certain assumptions that can be incompatible with sending
   multiple media types in a single RTP session.  Specifically, the RTP
   control protocol (RTCP) timing rules assume that all RTP media flows
   in a single RTP session have broadly similar RTCP reporting and
   feedback requirements, which can be problematic when different types
   of media are multiplexed together.  Various RTP extensions also make
   assumptions about SSRC use and RTCP reporting that are incompatible
   with sending different media types in a single RTP session.

   This memo updates [RFC3550] and [RFC3551] to allow RTP sessions to
   contain more than one media type in certain circumstances, and gives
   guidance on when it is safe to send multiple media types in a single
   RTP session.

4.  Applicability

   This specification has limited applicability, and anyone intending to
   use it needs to ensure that their application and use case meets the
   following criteria:

   Equal treatment of media:  The use of a single RTP session requires
      similar network treatment for all types of media used within the
      session.  Applications that require significantly different
      network quality of service (QoS) or RTCP configuration for
      different media streams are better suited by sending those media
      streams on separate RTP session, using separate transport layer



Westerlund, et al.        Expires June 12, 2016                 [Page 4]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


      flows for each, since that gives greater flexibility.  Further
      guidance on how to provide differential treatment for some media
      is given in [I-D.ietf-avtcore-multiplex-guidelines] and [RFC7657].

   Compatible RTCP Behaviour:  The RTCP timing rules enforce a single
      RTCP reporting interval for all participants in an RTP session.
      Flows with very different media sending rate or RTCP feedback
      requirements cannot be multiplexed together, since this leads to
      either excessive or insufficient RTCP for some flows, depending on
      how the RTCP session bandwidth, and hence reporting interval, is
      configured.  For example, it is likely infeasible to find a single
      RTCP configuration that simultaneously suits both a low-rate audio
      flow with no feedback, and a high-quality video flow with
      sophisticated RTCP-based feedback.  Thus, combining these into a
      single RTP session is difficult and/or inadvisable.

   Signalled Support:  The extensions defined in this memo are not
      compatible with unmodified [RFC3550]-compatible endpoints.  Their
      use requires signalling and mutual agreement by all participants
      within an RTP session.  This requirement can be a problem for
      signalling solutions that can't negotiate with all participants.
      For declarative signalling solutions, mandating that the session
      is using multiple media types in one RTP session can be a way of
      attempting to ensure that all participants in the RTP session
      follow the requirement.  However, for signalling solutions that
      lack methods for enforcing that a receiver supports a specific
      feature, this can still cause issues.

   Consistent support for multiparty RTP sessions:  If it is desired to
      send multiple types of media in a multiparty RTP session, then all
      participants in that session need to support sending multiple type
      of media in a single RTP session.  It is not possible, in the
      general case, to implement a gateway that can interconnect an
      endpoint using multiple types of media sent using separate RTP
      sessions, with one or more endpoints that send multiple types of
      media in a single RTP session.

      One reason for this is that the same SSRC value can safely be used
      for different streams in multiple RTP sessions, but when collapsed
      to a single RTP session there is an SSRC collision.  This would
      not be an issue, since SSRC collision detection will resolve the
      conflict, except that some RTP payload formats and extensions use
      matching SSRCs to identify related flows, and break when a single
      RTP session is used.

      A middlebox that remaps SSRC values when combining multiple RTP
      sessions into one also needs to be aware of all possible RTCP
      packet types that might be used, so that it can remap the SSRC



Westerlund, et al.        Expires June 12, 2016                 [Page 5]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


      values in those packets.  This is impossible to do without
      restricting the set of RTCP packet types that can be used to those
      that are known by the middlebox.  Such a middlebox might also have
      difficulty due to differences in configured RTCP bandwidth and
      other parameters between the RTP sessions.

      Finally, the use of a middlebox that translates SSRC values can
      negatively impact the possibility for loop detection, as SSRC/CSRC
      can't be used to detect the loops; instead some other RTP stream
      or media source identity name space that is common across all
      interconnect parts is needed.

   Ability to operate with limited payload type space:  An RTP session
      has only a single 7-bit payload type space for all its payload
      type numbers.  Some applications might find this space limiting
      when using different media types and RTP payload formats within a
      single RTP session.

   Avoids incompatible Extensions:  Some RTP and RTCP extensions rely on
      the existence of multiple RTP sessions and relate media streams
      between sessions.  Others report on particular media types, and
      cannot be used with other media types.  Applications that send
      multiple types of media into a single RTP session need to avoid
      such extensions.

5.  Using Multiple Media Types in a Single RTP Session

   This section defines what needs to be done or avoided to make an RTP
   session with multiple media types function without issues.

5.1.  Allowing Multiple Media Types in an RTP Session

   Section 5.2 of "RTP: A Transport Protocol for Real-Time Applications"
   [RFC3550] states:

      For example, in a teleconference composed of audio and video media
      encoded separately, each medium SHOULD be carried in a separate
      RTP session with its own destination transport address.

      Separate audio and video streams SHOULD NOT be carried in a single
      RTP session and demultiplexed based on the payload type or SSRC
      fields.

   This specification changes both of these sentences.  The first
   sentence is changed to:

      For example, in a teleconference composed of audio and video media
      encoded separately, each medium SHOULD be carried in a separate



Westerlund, et al.        Expires June 12, 2016                 [Page 6]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


      RTP session with its own destination transport address, unless
      specification [RFCXXXX] is followed and the application meets the
      applicability constraints.

   The second sentence is changed to:

      Separate audio and video media sources SHOULD NOT be carried in a
      single RTP session, unless the guidelines specified in [RFCXXXX]
      are followed.

   Second paragraph of Section 6 in RTP Profile for Audio and Video
   Conferences with Minimal Control [RFC3551] says:

      The payload types currently defined in this profile are assigned
      to exactly one of three categories or media types: audio only,
      video only and those combining audio and video.  The media types
      are marked in Tables 4 and 5 as "A", "V" and "AV", respectively.
      Payload types of different media types SHALL NOT be interleaved or
      multiplexed within a single RTP session, but multiple RTP sessions
      MAY be used in parallel to send multiple media types.  An RTP
      source MAY change payload types within the same media type during
      a session.  See the section "Multiplexing RTP Sessions" of RFC
      3550 for additional explanation.

   This specifications purpose is to override that existing SHALL NOT
   under certain conditions.  Thus this sentence also has to be changed
   to allow for multiple media type's payload types in the same session.
   The above sentence is changed to:

      Payload types of different media types SHALL NOT be interleaved or
      multiplexed within a single RTP session unless [RFCXXXX] is used,
      and the application conforms to the applicability constraints.
      Multiple RTP sessions MAY be used in parallel to send multiple
      media types.

   RFC-Editor Note: Please replace RFCXXXX with the RFC number of this
   specification when assigned.

5.2.  Demultiplexing media types within an RTP session

   When receiving packets from a transport layer flow, an endpoint will
   first separate the RTP and RTCP packets from the non-RTP packets, and
   pass them to the RTP/RTCP protocol handler.  The RTP and RTCP packets
   are then demultiplexed based on their SSRC into the different media
   streams.  For each media stream, incoming RTCP packets are processed,
   and the RTP payload type is used to select the appropriate media
   decoder.  This process remains the same irrespective of whether
   multiple media types are sent in a single RTP session or not.



Westerlund, et al.        Expires June 12, 2016                 [Page 7]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   It is important to note that the RTP payload type is never used to
   distinguish media streams.  The RTP packets are demultiplexed into
   media streams based on their SSRC, then the RTP payload type is used
   to select the correct media decoding pathway for each media stream.

5.3.  Per-SSRC Media Type Restrictions

   An SSRC in an RTP session can change between media formats of the
   same type, subject to certain restrictions [RFC7160], but MUST NOT
   change media type during its lifetime.  For example, an SSRC can
   change between different audio formats, but cannot start sending
   audio then change to sending video.  The lifetime of an SSRC ends
   when an RTCP BYE packet for that SSRC is sent, or when it ceases
   transmission for long enough that it times out for the other
   participants in the session.

   The main motivation is that a given SSRC has its own RTP timestamp
   and sequence number spaces.  The same way that you can't send two
   encoded streams of audio with the same SSRC, you can't send one
   encoded audio and one encoded video stream with the same SSRC.  Each
   encoded stream when made into an RTP stream needs to have the sole
   control over the sequence number and timestamp space.  If not, one
   would not be able to detect packet loss for that particular encoded
   stream.  Nor can one easily determine which clock rate a particular
   SSRCs timestamp will increase with.  For additional arguments why RTP
   payload type based multiplexing of multiple media sources doesn't
   work, see [I-D.ietf-avtcore-multiplex-guidelines].

   Within an RTP session where multiple media types have been configured
   for use, an SSRC can only send one type of media during its lifetime
   (i.e., it can switch between different audio codecs, since those are
   both the same type of media, but cannot switch between audio and
   video).  Different SSRCs MUST be used for the different media
   sources, the same way multiple media sources of the same media type
   already have to do.  The payload type will inform a receiver which
   media type the SSRC is being used for.  Thus the payload type MUST be
   unique across all of the payload configurations independent of media
   type that is used in the RTP session.

5.4.  RTCP Considerations

   When sending multiple types of media that have different rates in a
   single RTP session, endpoints MUST follow the guidelines for handling
   RTCP described in Section 7 of [I-D.ietf-avtcore-rtp-multi-stream].







Westerlund, et al.        Expires June 12, 2016                 [Page 8]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


6.  Extension Considerations

   This section outlines known issues and incompatibilities with RTP and
   RTCP extensions when multiple media types are used in a single RTP
   sessions.  Future extensions to RTP and RTCP need to consider, and
   document, any potential incompatibility.

6.1.  RTP Retransmission Payload Format

   The RTP Retransmission Payload Format [RFC4588] can operate in either
   SSRC-multiplexed mode or session-multiplex mode.

   In SSRC-multiplexed mode, retransmitted RTP packets are sent in the
   same RTP session as the original packets, but use a different SSRC
   with the same RTCP SDES CNAME.  If each endpoint sends only a single
   original RTP stream and a single retransmission RTP stream in the
   session, this is sufficient.  If an endpoint sends multiple original
   and retransmission RTP streams, as would occur when sending multiple
   media types in a single RTP session, then each original RTP stream
   and the retransmission RTP stream have to be associated using
   heuristics.  By having retransmission requests outstanding for only
   one SSRC not yet mapped, a receiver can determine the binding between
   original and retransmission RTP stream.  Another alternative is the
   use of different RTP payload types, allowing the signalled "apt"
   (associated payload type) parameter of the RTP retransmission payload
   format to be used to associate retransmitted and original packets.

   Session-multiplexed mode sends the retransmission RTP stream in a
   separate RTP session to the original RTP stream, but using the same
   SSRC for each, with association being done by matching SSRCs between
   the two sessions.  This is unaffected by the use of multiple media
   types in a single RTP session, since each media type will be sent
   using a different SSRC in the original RTP session, and the same
   SSRCs can be used in the retransmission session, allowing the streams
   to be associated.  This can be signalled using SDP with the BUNDLE
   [I-D.ietf-mmusic-sdp-bundle-negotiation] and FID grouping [RFC5888]
   extensions.  These SDP extensions require each "m=" line to only be
   included in a single FID group, but the RTP retransmission payload
   format uses FID groups to indicate the m= lines that form an original
   and retransmission pair.  Accordingly, when using the BUNDLE
   extension to allow multiple media types to be sent in a single RTP
   session, each original media source (m= line) that is retransmitted
   needs a corresponding m= line in the retransmission RTP session.  In
   case there are multiple media lines for retransmission, these media
   lines will form a independent BUNDLE group from the BUNDLE group with
   the source streams.





Westerlund, et al.        Expires June 12, 2016                 [Page 9]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   An example SDP fragment showing the grouping structures is provided
   in Figure 1.  This example is not legal SDP and only the most
   important attributes have been left in place.  Note that this SDP is
   not an initial BUNDLE offer.  As can be seen there are two bundle
   groups, one for the source RTP session and one for the
   retransmissions.  Then each of the media sources are grouped with its
   retransmission flow using FID, resulting in three more groupings.

          a=group:BUNDLE foo bar fiz
          a=group:BUNDLE zoo kelp glo
          a=group:FID foo zoo
          a=group:FID bar kelp
          a=group:FID fiz glo
          m=audio 10000 RTP/AVP 0
          a=mid:foo
          a=rtpmap:0 PCMU/8000
          m=video 10000 RTP/AVP 31
          a=mid:bar
          a=rtpmap:31 H261/90000
          m=video 10000 RTP/AVP 31
          a=mid:fiz
          a=rtpmap:31 H261/90000
          m=audio 40000 RTP/AVPF 99
          a=rtpmap:99 rtx/90000
          a=fmtp:99 apt=0;rtx-time=3000
          a=mid:zoo
          m=video 40000 RTP/AVPF 100
          a=rtpmap:100 rtx/90000
          a=fmtp:199 apt=31;rtx-time=3000
          a=mid:kelp
          m=video 40000 RTP/AVPF 100
          a=rtpmap:100 rtx/90000
          a=fmtp:199 apt=31;rtx-time=3000
          a=mid:glo

      Figure 1: SDP example of Session Multiplexed RTP Retransmission

6.2.  RTP Payload Format for Generic FEC

   The RTP Payload Format for Generic Forward Error Correction (FEC)
   [RFC5109] (and its predecessor [RFC2733]) can either send the FEC
   stream as a separate RTP stream, or it can send the FEC combined with
   the original RTP stream as a redundant encoding [RFC2198].

   When sending FEC as a separate stream, the RTP Payload Format for
   generic FEC requires that FEC stream to be sent in a separate RTP
   session to the original stream, using the same SSRC, with the FEC
   stream being associated by matching the SSRC between sessions.  The



Westerlund, et al.        Expires June 12, 2016                [Page 10]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   RTP session used for the original streams can include multiple RTP
   streams, and those RTP streams can use multiple media types.  The
   repair session only needs one RTP Payload type to indicate FEC data,
   irrespective of the number of FEC streams sent, since the SSRC is
   used to associate the FEC streams with the original streams.  Hence,
   it is RECOMMENDED that FEC stream use the "application/ulpfec" media
   type for [RFC5109], and the "application/parityfec" media type for
   [RFC2733].  It is legal, but NOT RECOMMENDED, to send FEC streams
   using media specific payload format names (e.g., if an original RTP
   session contains audio and video flows, for the associated FEC RTP
   session where to use the "audio/ulpfec" and "video/ulpfec" payload
   formats), since this unnecessarily uses up RTP payload type values,
   and adds no value for demultiplexing since there might be multiple
   streams of the same media type).

   The combination of an original RTP session using multiple media types
   with a associated generic FEC session can be signalled using SDP with
   the BUNDLE extension [I-D.ietf-mmusic-sdp-bundle-negotiation].  In
   this case, the RTP session carrying the FEC streams will be its own
   BUNDLE group.  The m= line for each original stream and the m= line
   for the corresponding FEC stream are grouped using the SDP grouping
   framework using either the FEC-FR [RFC5956] grouping or, for
   backwards compatibility, the FEC [RFC4756] grouping.  This is similar
   to the situation that arises for RTP retransmission with session
   multiplexing discussed in Section 6.1.

   The Source-Specific Media Attributes [RFC5576] specification defines
   an SDP extension (the "FEC" semantic of the "ssrc-group" attribute)
   to signal FEC relationships between multiple RTP streams within a
   single RTP session.  This cannot be used with generic FEC, since the
   FEC repair packets need to have the same SSRC value as the source
   packets being protected.  There is ongoing work on an ULP extension
   to allow it be use FEC RTP streams within the same RTP Session as the
   source stream [I-D.lennox-payload-ulp-ssrc-mux].

   When the FEC is sent as a redundant encoding, the considerations in
   Section 6.3 apply.

6.3.  RTP Payload Format for Redundant Audio

   The RTP Payload Format for Redundant Audio [RFC2198] can be used to
   protect audio streams.  It can also be used along with the generic
   FEC payload format to send original and repair data in the same RTP
   packets.  Both are compatible with RTP sessions containing multiple
   media types.

   This payload format requires each different redundant encoding use a
   different RTP payload type number.  When used with generic FEC in



Westerlund, et al.        Expires June 12, 2016                [Page 11]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   sessions that contain multiple media types, this requires each media
   type use a different payload type for the FEC stream.  For example,
   if audio and text are sent in a single RTP session with generic ULP
   FEC sent as a redundant encoding for each, then payload types need to
   be assigned for FEC using the audio/ulpfec and text/ulpfec payload
   formats.  If multiple original payload types are used in the session,
   different redundant payload types need to be allocated for each one.
   This has potential to rapidly exhaust the available RTP payload type
   numbers.

7.  Signalling

   Establishing a single RTP session using multiple media types requires
   signalling.  This signalling has to:

   1.  ensure that any participant in the RTP session is aware that this
       is an RTP session with multiple media types;

   2.  ensure that the payload types in use in the RTP session are using
       unique values, with no overlap between the media types;

   3.  ensure RTP session level parameters, for example the RTCP RR and
       RS bandwidth modifiers, the RTP/AVPF trr-int parameter, transport
       protocol, RTCP extensions in use, and any security parameters,
       are consistent across the session; and

   4.  ensure that RTP and RTCP functions that can be bound to a
       particular media type are reused where possible, rather than
       configuring multiple code-points for the same thing.

   When using SDP signalling, the BUNDLE extension
   [I-D.ietf-mmusic-sdp-bundle-negotiation] is used to signal RTP
   sessions containing multiple media types.

8.  Security Considerations

   RTP provides a range of strong security mechanisms that can be used
   to secure sessions [RFC7201], [RFC7202].  The majority of these are
   independent of the type of media sent in the RTP session; however it
   is important to check that the security mechanism chosen is
   compatible with all types of media sent within the session.

   Sending multiple media types in a single RTP session will generally
   require that all use the same security mechanism, whereas media sent
   using different RTP sessions can be secured in different ways.  When
   different media types have different security requirements, it might
   be necessary to send them using separate RTP sessions to meet those




Westerlund, et al.        Expires June 12, 2016                [Page 12]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   different requirements.  This can have significant costs in terms of
   resource usage, session set-up time, etc.

9.  IANA Considerations

   This memo makes no request of IANA.

10.  Acknowledgements

   The authors would like to thank Christer Holmberg, Gunnar Hellstroem,
   Charles Eckel, Tolga Asveren, and Warren Kumari for their feedback on
   the document.

11.  References

11.1.  Normative References

   [I-D.ietf-avtcore-rtp-multi-stream]
              Lennox, J., Westerlund, M., Wu, W., and C. Perkins,
              "Sending Multiple Media Streams in a Single RTP Session",
              draft-ietf-avtcore-rtp-multi-stream-10 (work in progress),
              November 2015.

   [I-D.ietf-mmusic-sdp-bundle-negotiation]
              Holmberg, C., Alvestrand, H., and C. Jennings,
              "Negotiating Media Multiplexing Using the Session
              Description Protocol (SDP)", draft-ietf-mmusic-sdp-bundle-
              negotiation-23 (work in progress), July 2015.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <http://www.rfc-editor.org/info/rfc3550>.

   [RFC3551]  Schulzrinne, H. and S. Casner, "RTP Profile for Audio and
              Video Conferences with Minimal Control", STD 65, RFC 3551,
              DOI 10.17487/RFC3551, July 2003,
              <http://www.rfc-editor.org/info/rfc3551>.








Westerlund, et al.        Expires June 12, 2016                [Page 13]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


11.2.  Informative References

   [I-D.ietf-avtcore-multiplex-guidelines]
              Westerlund, M., Perkins, C., and H. Alvestrand,
              "Guidelines for using the Multiplexing Features of RTP to
              Support Multiple Media Streams", draft-ietf-avtcore-
              multiplex-guidelines-03 (work in progress), October 2014.

   [I-D.lennox-payload-ulp-ssrc-mux]
              Lennox, J., "Supporting Source-Multiplexing of the Real-
              Time Transport Protocol (RTP) Payload for Generic Forward
              Error Correction", draft-lennox-payload-ulp-ssrc-mux-00
              (work in progress), February 2013.

   [RFC2198]  Perkins, C., Kouvelas, I., Hodson, O., Hardman, V.,
              Handley, M., Bolot, J., Vega-Garcia, A., and S. Fosse-
              Parisis, "RTP Payload for Redundant Audio Data", RFC 2198,
              DOI 10.17487/RFC2198, September 1997,
              <http://www.rfc-editor.org/info/rfc2198>.

   [RFC2733]  Rosenberg, J. and H. Schulzrinne, "An RTP Payload Format
              for Generic Forward Error Correction", RFC 2733,
              DOI 10.17487/RFC2733, December 1999,
              <http://www.rfc-editor.org/info/rfc2733>.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, DOI 10.17487/RFC4566,
              July 2006, <http://www.rfc-editor.org/info/rfc4566>.

   [RFC4588]  Rey, J., Leon, D., Miyazaki, A., Varsa, V., and R.
              Hakenberg, "RTP Retransmission Payload Format", RFC 4588,
              DOI 10.17487/RFC4588, July 2006,
              <http://www.rfc-editor.org/info/rfc4588>.

   [RFC4756]  Li, A., "Forward Error Correction Grouping Semantics in
              Session Description Protocol", RFC 4756,
              DOI 10.17487/RFC4756, November 2006,
              <http://www.rfc-editor.org/info/rfc4756>.

   [RFC5109]  Li, A., Ed., "RTP Payload Format for Generic Forward Error
              Correction", RFC 5109, DOI 10.17487/RFC5109, December
              2007, <http://www.rfc-editor.org/info/rfc5109>.

   [RFC5576]  Lennox, J., Ott, J., and T. Schierl, "Source-Specific
              Media Attributes in the Session Description Protocol
              (SDP)", RFC 5576, DOI 10.17487/RFC5576, June 2009,
              <http://www.rfc-editor.org/info/rfc5576>.




Westerlund, et al.        Expires June 12, 2016                [Page 14]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   [RFC5888]  Camarillo, G. and H. Schulzrinne, "The Session Description
              Protocol (SDP) Grouping Framework", RFC 5888,
              DOI 10.17487/RFC5888, June 2010,
              <http://www.rfc-editor.org/info/rfc5888>.

   [RFC5956]  Begen, A., "Forward Error Correction Grouping Semantics in
              the Session Description Protocol", RFC 5956,
              DOI 10.17487/RFC5956, September 2010,
              <http://www.rfc-editor.org/info/rfc5956>.

   [RFC6466]  Salgueiro, G., "IANA Registration of the 'image' Media
              Type for the Session Description Protocol (SDP)",
              RFC 6466, DOI 10.17487/RFC6466, December 2011,
              <http://www.rfc-editor.org/info/rfc6466>.

   [RFC7160]  Petit-Huguenin, M. and G. Zorn, Ed., "Support for Multiple
              Clock Rates in an RTP Session", RFC 7160,
              DOI 10.17487/RFC7160, April 2014,
              <http://www.rfc-editor.org/info/rfc7160>.

   [RFC7201]  Westerlund, M. and C. Perkins, "Options for Securing RTP
              Sessions", RFC 7201, DOI 10.17487/RFC7201, April 2014,
              <http://www.rfc-editor.org/info/rfc7201>.

   [RFC7202]  Perkins, C. and M. Westerlund, "Securing the RTP
              Framework: Why RTP Does Not Mandate a Single Media
              Security Solution", RFC 7202, DOI 10.17487/RFC7202, April
              2014, <http://www.rfc-editor.org/info/rfc7202>.

   [RFC7656]  Lennox, J., Gross, K., Nandakumar, S., Salgueiro, G., and
              B. Burman, Ed., "A Taxonomy of Semantics and Mechanisms
              for Real-Time Transport Protocol (RTP) Sources", RFC 7656,
              DOI 10.17487/RFC7656, November 2015,
              <http://www.rfc-editor.org/info/rfc7656>.

   [RFC7657]  Black, D., Ed. and P. Jones, "Differentiated Services
              (Diffserv) and Real-Time Communication", RFC 7657,
              DOI 10.17487/RFC7657, November 2015,
              <http://www.rfc-editor.org/info/rfc7657>.

Authors' Addresses










Westerlund, et al.        Expires June 12, 2016                [Page 15]


Internet-Draft   Multiple Media Types in an RTP Session    December 2015


   Magnus Westerlund
   Ericsson
   Farogatan 6
   SE-164 80 Kista
   Sweden

   Phone: +46 10 714 82 87
   Email: magnus.westerlund@ericsson.com


   Colin Perkins
   University of Glasgow
   School of Computing Science
   Glasgow  G12 8QQ
   United Kingdom

   Email: csp@csperkins.org


   Jonathan Lennox
   Vidyo, Inc.
   433 Hackensack Avenue
   Seventh Floor
   Hackensack, NJ  07601
   US

   Email: jonathan@vidyo.com
























Westerlund, et al.        Expires June 12, 2016                [Page 16]