Internet Engineering Task Force                        S. Perreault, Ed.
Internet-Draft                                                  Viagenie
Intended status: BCP                                         I. Yamagata
Expires: June 2, 2012                                        S. Miyakawa
                                                      NTT Communications
                                                             A. Nakagawa
                                          Japan Internet Exchange (JPIX)
                                                               H. Ashida
                                                      IS Consulting G.K.
                                                       November 30, 2011


           Common requirements for Carrier Grade NATs (CGNs)
                 draft-ietf-behave-lsn-requirements-05

Abstract

   This document defines common requirements for Carrier-Grade NAT
   (CGN).

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on June 2, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.




Perreault, et al.         Expires June 2, 2012                  [Page 1]


Internet-Draft              CGN Requirements               November 2011


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the BSD License.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   3.  Requirements for CGNs  . . . . . . . . . . . . . . . . . . . .  4
   4.  Logging  . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
   5.  Bulk Port Allocation . . . . . . . . . . . . . . . . . . . . . 10
   6.  Deployment Considerations  . . . . . . . . . . . . . . . . . . 12
   7.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 12
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 12
   9.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 12
   10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 13
     10.1.  Normative References  . . . . . . . . . . . . . . . . . . 13
     10.2.  Informative Reference . . . . . . . . . . . . . . . . . . 13
   Appendix A.  Change Log (to be removed by RFC Editor prior to
                publication)  . . . . . . . . . . . . . . . . . . . . 14
     A.1.   Changed in -05  . . . . . . . . . . . . . . . . . . . . . 14
     A.2.   Changed in -04  . . . . . . . . . . . . . . . . . . . . . 15
     A.3.   Changed in -03  . . . . . . . . . . . . . . . . . . . . . 15
     A.4.   Changed in -02  . . . . . . . . . . . . . . . . . . . . . 16
     A.5.   Changed in -01  . . . . . . . . . . . . . . . . . . . . . 17
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 17


















Perreault, et al.         Expires June 2, 2012                  [Page 2]


Internet-Draft              CGN Requirements               November 2011


1.  Introduction

   With the shortage of IPv4 addresses, it is expected that more ISPs
   may want to provide a service where a public IPv4 address would be
   shared by many subscribers.  Each subscriber is assigned a private
   address, and a NAT situated in the ISP's network translates between
   private and public addresses.  When a second IPv4 NAT is located at
   the customer edge, this results in two layers of NAT.

   This is not to be considered a solution to the shortage of IPv4
   addresses.  It is a service that can conceivably be offered alongside
   others, such as IPv6 services or regular, un-NATed IPv4 service.
   Some ISPs started offering such a service long before there was a
   shortage of IPv4 addresses, showing that there are driving forces
   other than the shortage of IPv4 addresses.

   This document describes behavioral requirements that are to be
   expected of those multi-subscriber NATs.  Meeting this set of
   requirements will greatly increase the likelihood that subscribers'
   applications will function properly.

   Readers should be aware of potential issues that may arise when
   sharing a public address between many subscribers.  See [RFC6269] for
   details.

   This document builds upon previous works describing requirements for
   generic NATs [RFC4787][RFC5382][RFC5508].  These documents, and their
   updates if any, still apply in this context.  What follows are
   additional requirements, to be satisfied on top of previous ones.


2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   Readers are expected to be familiar with [RFC4787] and the terms
   defined there.  The following additional term is used in this
   document:

   Carrier-Grade NAT (CGN):  A NAT-based [RFC2663] functional element
      operated by an administrative entity (e.g., operator) to share the
      same address among several subscribers.  A CGN is managed by the
      administrative entity, not the subscribers.

         Note that the term "carrier-grade" has nothing to do with the
         quality of the NAT; that is left to discretion of implementers.



Perreault, et al.         Expires June 2, 2012                  [Page 3]


Internet-Draft              CGN Requirements               November 2011


         Rather, it is to be understood as a topological qualifier: the
         NAT is placed in an ISP's network and translates the traffic of
         potentially many subscribers.  Subscribers have limited or no
         control over the CGN, whereas they typically have full control
         over a NAT placed on their premises.

   Figure 1 summarizes a common network topology in which a CGN
   operates.

                                  .
                                  :
                                  |       Internet
                  ............... | ...................
                                  |       ISP network
                                  |
                                  |
                              ++------++  External realm
                  ........... |  CGN   |...............
                              ++------++  Internal realm
                                |    |
                                |    |
                                |    |    ISP network
                  ............. | .. | ................
                                |    |  Customer premises
                        ++------++  ++------++
                        |  CPE1  |  |  CPE2  |  etc.
                        ++------++  ++------++

                      Figure 1: CGN network topology

   Another possible topology is one for hotspots, where there is no
   customer premise or customer-premises equipment (CPE), but where a
   CGN serves a bunch of customers who don't trust each other and hence
   fairness is an issue.  One important difference with the previous
   topology is the absence of a second layer of NAT.  This, however, has
   no impact on CGN requirements since they are driven by fairness and
   robustness in the service provided to customers, which applies in
   both cases.


3.  Requirements for CGNs

   What follows is a list of requirements for CGNs.  They are in
   addition to those found in other documents such as [RFC4787],
   [RFC5382], and [RFC5508].






Perreault, et al.         Expires June 2, 2012                  [Page 4]


Internet-Draft              CGN Requirements               November 2011


   REQ-1:  A CGN MUST support at least the following transport
           protocols: TCP (MUST support [RFC5382]), UDP (MUST support
           [RFC4787]), and ICMP (MUST support [RFC5508]).  Support for
           additional transport protocols is OPTIONAL.

   Justification:  These protocols are the ones that NATs traditionally
      support.  The IETF has documented the best current practices for
      them.

   REQ-2:  A CGN MUST have a default "IP address pooling" behavior of
           "Paired" (as defined in [RFC4787] section 4.1).  A CGN MAY
           provide a mechanism for administrators to change this
           behavior on an application protocol basis.

           *  When multiple overlapping internal IP address ranges share
              the same external IP address pool (e.g., DS-Lite
              [RFC6333]), the "IP address pooling" behavior applies to
              mappings between external IP addresses and internal
              subscribers rather than between external and internal IP
              addresses.

   Justification:  This stronger form of REQ-2 from [RFC4787] is
      justified by the stronger need for not breaking applications that
      depend on the external address remaining constant.

      Note that this requirement applies regardless of the transport
      protocol.  In other words, a CGN must use the same external IP
      address mapping for all sessions associated with the same internal
      IP address, be they TCP, UDP, ICMP, something else, or a mix of
      different protocols.

      The justification for allowing other behaviors is to allow the
      administrator to save external addresses and ports for application
      protocols that are known to work fine with other behaviors in
      practice.  However, the default behavior MUST be "Paired".

   REQ-3:  The CGN function SHOULD NOT have any limitations on the size
           nor the contiguity of the external address pool.  In
           particular, the CGN function SHOULD be configurable with
           contiguous or non-contiguous external IPv4 address ranges.

   Justification:  Given the increasing rarity of IPv4 addresses, it is
      becoming harder for an operator to provide large contiguous
      address pools to CGNs.  Additionally, operational flexibility may
      require non-contiguous address pools for reasons such as
      differentiated services, routing management, etc.





Perreault, et al.         Expires June 2, 2012                  [Page 5]


Internet-Draft              CGN Requirements               November 2011


   REQ-4:  A CGN SHOULD support limiting the number of external ports
           (or, equivalently, "identifiers" for ICMP) that are assigned
           per subscriber.

           A.  Limits SHOULD be configurable by the CGN administrator.

           B.  Limits MAY be configurable independently per transport
               protocol.

           C.  Additionally, it is RECOMMENDED that the CGN include
               administrator-adjustable thresholds to prevent a single
               subscriber from consuming excessive CPU resources from
               the CGN (e.g., rate limit the subscriber's creation of
               new mappings).

   Justification:  A CGN can be considered a network resource that is
      shared by competing subscribers.  Limiting the number of external
      ports assigned to each subscriber mitigates the DoS attack that a
      subscriber could launch against other subscribers through the CGN
      in order to get a larger share of the resource.  It ensures
      fairness among subscribers.  Limiting the rate of allocation
      mitigates a similar attack where the CPU is the resource being
      targeted instead of port numbers.

   REQ-5:  A CGN SHOULD support limiting the amount of state memory
           allocated per mapping and per subscriber.  This may include
           limiting the number of sessions, the number of filters, etc.,
           depending on the NAT implementation.

           A.  Limits SHOULD be configurable by the CGN administrator.

           B.  Additionally, it SHOULD be possible to limit the rate at
               which memory-consuming state elements are allocated.

   Justification:  A NAT needs to keep track of TCP sessions associated
      to each mapping.  This state consumes resources for which, in the
      case of a CGN, subscribers may compete.  It is necessary to ensure
      that each subscriber has access to a fair share of the CGN's
      resources.  Limiting TCP sessions per subscriber and per time unit
      is an effective mitigation against inter-subscriber DoS attacks.
      Limiting the rate of allocation is intended to prevent against CPU
      resource exhaustion.

   REQ-6:  It SHOULD be possible to administratively turn off
           translation for specific destination addresses and/or ports.






Perreault, et al.         Expires June 2, 2012                  [Page 6]


Internet-Draft              CGN Requirements               November 2011


   Justification:  It is common for a CGN administrator to provide
      access for subscribers to servers installed in the ISP's network,
      in the external realm.  When such a server is able to reach the
      internal realm via normal routing (which is entirely controlled by
      the ISP), translation is unneeded.  In that case, the CGN may
      forward packets without modification, thus acting like a plain
      router.  This may represent an important efficiency gain.

      Figure 2 illustrates this use-case.


                 X1:x1            X1':x1'            X2:x2
                 +---+from X1:x1  +---+from X1:x1    +---+
                 | C |  to X2:x2  |   |  to X2:x2    | S |
                 | l |>>>>>>>>>>>>| C |>>>>>>>>>>>>>>| e |
                 | i |            | G |              | r |
                 | e |<<<<<<<<<<<<| N |<<<<<<<<<<<<<<| v |
                 | n |from X2:x2  |   |from X2:x2    | e |
                 | t |  to X1:x1  |   |  to X1:x1    | r |
                 +---+            +---+              +---+

                        Figure 2: CGN pass-through

   REQ-7:  It is RECOMMENDED that a CGN have an "Endpoint-Independent
           Filtering" behavior (as defined in [RFC4787] section 5).  If
           it is known that "Address-Independent Filtering" does not
           cause the application-layer protocol to break (how to
           determine this is out of scope for this document), then it
           MAY be used instead.

   Justification:  This is a stronger form of REQ-8 from [RFC4787].
      This is based on the observation that some games and peer-to-peer
      applications require EIF for the NAT traversal to work.  In the
      context of a CGN it is important to minimize application breakage.

   REQ-8:  When a CGN loses state (due to a crash, reboot, failover to a
           cold standby, etc.), it MUST NOT reuse the same external
           address+port pairs for new dynamic mappings for at least 120
           seconds, except for any of the following cases:

           A.  If the CGN tracks TCP sessions (e.g., with a state
               machine, as in [RFC6146] section 3.5.2.2), TCP ports MAY
               be reused immediately.

           B.  If external ports are statically assigned to internal
               addresses (e.g., address X with port range 1000-1999 is
               assigned to subscriber A, 2000-2999 to subscriber B,
               etc.), and the assignment remains constant across state



Perreault, et al.         Expires June 2, 2012                  [Page 7]


Internet-Draft              CGN Requirements               November 2011


               loss, then ports MAY be reused immediately.

   Justification:  This is necessary in order to prevent collisions
      between old and new mappings and sessions.  It ensures that all
      established sessions are broken instead of redirected to a
      different peer.

      The exceptions are for cases where reusing a port immediately does
      not create a possibility that packets would be redirected to the
      wrong peer.

      The 120 seconds value corresponds to the Maximum Segment Lifetime
      (MSL) from [RFC0793].

      One way that this requirement could be satisfied would be have two
      distinct address pools: one dormant and one active.  When
      rebooting, the CGN would swap the dormant pool with the active
      pool.  Another way would be simply to wait 120 seconds before
      resuming NAT activity.

   REQ-9:  Once an external port is deallocated, it SHOULD NOT be
           reallocated to a new mapping until at least 120 seconds have
           passed.  The length of time and the maximum number of ports
           in this state SHOULD be configurable by the CGN
           administrator.  The following exceptions apply:

           A.  If the CGN tracks TCP sessions (e.g., with a state
               machine, as in [RFC6146] section 3.5.2.2), TCP ports MAY
               be reused immediately.

           B.  If the allocated external ports used address-dependent or
               address-and-port-dependent filtering before state loss,
               they MAY be reused immediately.

   Justification:  This is to prevent users from receiving unwanted
      traffic.  It also helps prevent against clock skew when mappings
      are logged.

      The exceptions are for cases where reusing a port immediately does
      not create a possibility that packets would be redirected to the
      wrong peer.

      The 120 seconds value corresponds to the Maximum Segment Lifetime
      (MSL) from [RFC0793].







Perreault, et al.         Expires June 2, 2012                  [Page 8]


Internet-Draft              CGN Requirements               November 2011


   REQ-10:  A CGN SHOULD include a Port Control Protocol server
            [I-D.ietf-pcp-base].

   Justification:  Allowing subscribers to manipulate the NAT state
      table with PCP greatly increases the likelihood that applications
      will function properly.

   REQ-11:  A CGN SHOULD support [RFC4008].

   Justification:  It is anticipated that CGNs will be primarily
      deployed in ISP networks where the need for management is
      critical.

      Note also that there are efforts within the IETF toward creating a
      MIB tailored for CGNs (e.g., [I-D.perreault-opsawg-natmib-bis]).

   REQ-12:  When a CGN is unable to create a mapping due to resource
            constraints or administrative restrictions (i.e., quotas):

            A.  it MUST drop the original packet;

            B.  it SHOULD send an ICMP Destination Unreachable message
                with code 3 (Port Unreachable) to the session initiator;

            C.  it SHOULD send a notification (e.g., SNMP trap) towards
                a management system (if configured to do so);

            D.  and it SHOULD NOT delete existing mappings in order to
                "make room" for the new one.  (This only applies to
                normal CGN behavior, not to manual operator
                intervention.)

   Justification:  This is a slightly different form of REQ-8 from
      [RFC5508].  Code 3 is preferred to code 13 because it is listed as
      a "soft error" in [RFC5461], which is important because we don't
      want TCP stacks to abort the connection attempt in this case.
      Sending an ICMP error may be rate-limited for security reasons,
      which is why requirement B is a SHOULD, not a MUST.

      Applications generally handle connection establishment failure
      better than established connection failure.  This is why dropping
      the packet initiating the new connection is preferred over
      deleting existing mappings.  See also the rationale in [RFC5508]
      section 6.







Perreault, et al.         Expires June 2, 2012                  [Page 9]


Internet-Draft              CGN Requirements               November 2011


4.  Logging

   It may be necessary for CGN administrators to be able to identify a
   subscriber based on external IPv4 address, port, and timestamp in
   order to deal with abuse and lawful intercept requests.  When
   multiple subscribers share a single external address, the source
   address and port that are visible at the destination host have been
   translated from the ones originated by the subscriber.

   In order to be able to do this, the CGN would need to log the
   following information for each mapping created:

   o  subscriber identifier (e.g., internal source address or tunnel
      endpoint identifier)

   o  external source address

   o  external source port

   o  timestamp

   By "subscriber identifier" we mean information that uniquely
   identifies a subscriber.  For example, in a traditional NAT scenario,
   the internal source address would be sufficient.  In the case of DS-
   Lite, many subscribers share the same internal address and the
   subscriber identifier is the tunnel endpoint identifier (i.e., the
   B4's IPv6 address).

   A disadvantage of logging mappings is that CGNs under heavy usage may
   produce large amounts of logs, which may require large storage
   volume.

   REQ-13:  A CGN SHOULD NOT log destination addresses or ports.

   Justification:  Destination logging at the CGN creates privacy
      issues.  Furthermore, readers should be aware of logging
      recommendations for Internet-facing servers [RFC6302].  With
      compliant servers, the destination address and port do not need to
      be logged by the CGN.  This can help reduce the amount of logging.


5.  Bulk Port Allocation

   So far we have assumed that a CGN allocates one external port for
   every outgoing connection.  In this section, the impacts of
   allocating multiple external ports at a time are discussed.

   There is a range of things a CGN can do:



Perreault, et al.         Expires June 2, 2012                 [Page 10]


Internet-Draft              CGN Requirements               November 2011


   Traditional:  For every outgoing connection, allocate one external
      port.

   Scattered port set:  For an outgoing connection, create a set of
      several non-consecutive external ports.  Subsequent outgoing
      connections will use ports from the set.  When the set is
      exhausted, a new connection causes a new set to be created.  A set
      is smaller or equal to the user's maximum port limit.

   Consecutive port set:  Same as the scattered port set, but the ports
      allocated to a set are consecutive.

   Note that this list is not exhaustive.  There is a continuum of
   behavior that a CGN may choose to implement.  For example, a CGN
   could use scattered port sets of consecutive port sets.

   The impacts of bulk port allocation are as follows.

   Port Utilization:  The mechanisms at the top of the list are very
      efficient in their port utilization.  In that sense, they have
      good scaling properties (nothing is wasted).  The mechanisms at
      the bottom of the list will waste ports.  The number of wasted
      ports is proportional to size of the "bin".

   Logging:  Traditional allocation creates a lot of log entries as
      compared to allocation by port sets which creates much fewer
      entries.  Scattered and consecutive port sets generate the same
      number of log entries.  In the case of consecutive port sets,
      entries can be expressed very compactly by indicating a range
      (e.g., "12000-12009").  Some scattered port set allocation schemes
      can also generate small log entries containing the parameters and
      algorithm used for the port set generation (see, e.g.,
      [I-D.boucadair-pppext-portrange-option]).

      With large set sizes, the logging frequency for scattered and
      consecutive port sets can approach that of DHCP servers.

      Logging destination addresses and ports can only be done on a per-
      session basis.  This means that destination logging for a CGN
      implementing bulk port allocation would create one log entry per
      session containing the destination address and port.  Other
      information could still be logged in one entry per port set.

   Security:  Traditional and scattered port sets provide very good
      security in that ports numbers are not easily guessed.  Easily
      guessed port numbers put subscribers at risk of the attacks
      described in [RFC6056].  Consecutive port sets provides poor
      security to subscribers, especially if the set size is small.



Perreault, et al.         Expires June 2, 2012                 [Page 11]


Internet-Draft              CGN Requirements               November 2011


6.  Deployment Considerations

   Several issues are encountered when CGNs are used [RFC6269].  There
   is current work in the IETF toward alleviating some of these issues.
   For example, see [I-D.boucadair-intarea-nat-reveal-analysis].

   The address sharing ratio is the ratio between the number of external
   addresses and the number of internal addresses that a CGN is
   configured to handle.  See [RFC6269] section 26.2 for guidance on
   picking an appropriate ratio.


7.  IANA Considerations

   There are no IANA considerations.


8.  Security Considerations

   If a malicious subscriber can spoof another subscriber's CPE, it may
   cause a DoS to that subscriber by creating mappings up to the allowed
   limit.  Preventing this can be accomplished with ingress filtering,
   as described in [RFC2827].

   Endpoint-Independent Filtering has security considerations which are
   discussed in [RFC4787].

   NATs sometimes perform fragment reassembly.  CGNs would do so at
   presumably high data rates.  Therefore, the reader should be familiar
   with the potential security issues described in [RFC4963].


9.  Acknowledgements

   Thanks for the input and review by Arifumi Matsumoto, Benson
   Schliesser, Dai Kuwabara, Dan Wing, Dave Thaler, Francis Dupont, Joe
   Touch, Lars Eggert, Kousuke Shishikura, Mohamed Boucadair, Nejc
   Skoberne, Reinaldo Penno, Senthil Sivakumar, Takanori Mizuguchi,
   Takeshi Tomochika, Tina Tsou, Tomohiro Fujisaki, Tomohiro Nishitani,
   Tomoya Yoshida, and Yasuhiro Shirasaki.  Dan Wing also contributed
   much of section 5.


10.  References







Perreault, et al.         Expires June 2, 2012                 [Page 12]


Internet-Draft              CGN Requirements               November 2011


10.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC4008]  Rohit, R., Srisuresh, P., Raghunarayan, R., Pai, N., and
              C. Wang, "Definitions of Managed Objects for Network
              Address Translators (NAT)", RFC 4008, March 2005.

   [RFC4787]  Audet, F. and C. Jennings, "Network Address Translation
              (NAT) Behavioral Requirements for Unicast UDP", BCP 127,
              RFC 4787, January 2007.

   [RFC5382]  Guha, S., Biswas, K., Ford, B., Sivakumar, S., and P.
              Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142,
              RFC 5382, October 2008.

   [RFC5508]  Srisuresh, P., Ford, B., Sivakumar, S., and S. Guha, "NAT
              Behavioral Requirements for ICMP", BCP 148, RFC 5508,
              April 2009.

   [I-D.ietf-pcp-base]
              Wing, D., Cheshire, S., Boucadair, M., Penno, R., and P.
              Selkirk, "Port Control Protocol (PCP)",
              draft-ietf-pcp-base-16 (work in progress), October 2011.

10.2.  Informative Reference

   [RFC0793]  Postel, J., "Transmission Control Protocol", STD 7,
              RFC 793, September 1981.

   [RFC2663]  Srisuresh, P. and M. Holdrege, "IP Network Address
              Translator (NAT) Terminology and Considerations",
              RFC 2663, August 1999.

   [RFC2827]  Ferguson, P. and D. Senie, "Network Ingress Filtering:
              Defeating Denial of Service Attacks which employ IP Source
              Address Spoofing", BCP 38, RFC 2827, May 2000.

   [RFC4963]  Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly
              Errors at High Data Rates", RFC 4963, July 2007.

   [RFC5461]  Gont, F., "TCP's Reaction to Soft Errors", RFC 5461,
              February 2009.

   [RFC6056]  Larsen, M. and F. Gont, "Recommendations for Transport-
              Protocol Port Randomization", BCP 156, RFC 6056,
              January 2011.



Perreault, et al.         Expires June 2, 2012                 [Page 13]


Internet-Draft              CGN Requirements               November 2011


   [RFC6146]  Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful
              NAT64: Network Address and Protocol Translation from IPv6
              Clients to IPv4 Servers", RFC 6146, April 2011.

   [RFC6269]  Ford, M., Boucadair, M., Durand, A., Levis, P., and P.
              Roberts, "Issues with IP Address Sharing", RFC 6269,
              June 2011.

   [RFC6302]  Durand, A., Gashinsky, I., Lee, D., and S. Sheppard,
              "Logging Recommendations for Internet-Facing Servers",
              BCP 162, RFC 6302, June 2011.

   [RFC6333]  Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
              Stack Lite Broadband Deployments Following IPv4
              Exhaustion", RFC 6333, August 2011.

   [I-D.boucadair-intarea-nat-reveal-analysis]
              Boucadair, M., Touch, J., Levis, P., and R. Penno,
              "Analysis of Solution Candidates to Reveal a Host
              Identifier in Shared Address Deployments",
              draft-boucadair-intarea-nat-reveal-analysis-04 (work in
              progress), September 2011.

   [I-D.boucadair-pppext-portrange-option]
              Boucadair, M., Levis, P., Bajko, G., Savolainen, T., and
              T. Tsou, "Huawei Port Range Configuration Options for PPP
              IPCP", draft-boucadair-pppext-portrange-option-09 (work in
              progress), September 2011.

   [I-D.perreault-opsawg-natmib-bis]
              Perreault, S. and T. ZOU), "Definitions of Managed Objects
              for Network Address Translators (NAT)",
              draft-perreault-opsawg-natmib-bis-00 (work in progress),
              September 2011.


Appendix A.  Change Log (to be removed by RFC Editor prior to
             publication)

A.1.  Changed in -05

   o  Removed DSCP requirement since it applies to non-CG NATs as well.

   o  Removed instances of "NAT444".

   o  Filtering has no effect on the requirement for a hold down pool.
      Removed REQ-8-B.




Perreault, et al.         Expires June 2, 2012                 [Page 14]


Internet-Draft              CGN Requirements               November 2011


   o  Statically assigned port ranges do not need to go in the hold down
      pool.  Added a new REQ-8-B.

   o  Fixed various nits.  More precise text in some places.

A.2.  Changed in -04

   o  Fixed nits, spelling, updated references.

   o  CGNs SHOULD NOT log destinations.

   o  Allow address-dependent filtering when it does not cause the
      application protocol to break.

   o  Refer to RFC4787 security considerations on EIF.

   o  Clarify REQ-12 point D (it does not apply to operator
      intervention).

   o  Changed "CGNs SHOULD limit ..." to "SHOULD support limiting" to
      make it clear that the operator is in control.

   o  Added reference to RFC 4963.

   o  Added requirement for non-contiguous external address pools.

A.3.  Changed in -03

   o  Added exceptions for which it is not necessary to wait 120 seconds
      before reusing a port.

   o  Renamed "random port set" to "scattered port set", which is more
      accurate.

   o  Log "subscriber identifier" instead of internal address+port to
      allow for overlapping internal address ranges (DS-Lite).

   o  Adjusted logging text and added reference to I-D.boucadair-pppext-
      portrange-option.

   o  Adjusted destination logging text for bulk port allocation
      schemes.

   o  Removed requirement for I-D.ietf-intarea-ipv4-id-update.

   o  Made PCP support a SHOULD-level requirement.





Perreault, et al.         Expires June 2, 2012                 [Page 15]


Internet-Draft              CGN Requirements               November 2011


   o  Lowered the level of requirement for not dropping existing
      mappings in order to "make room" to SHOULD level, and added
      rationale.

A.4.  Changed in -02

   o  CGNs MUST support at least TCP, UDP, and ICMP.

   o  Add requirement from I-D.ietf-intarea-ipv4-id-update.

   o  Add informative reference to [RFC6269].

   o  Add requirement (SHOULD level) for a port forwarding protocol.

   o  Allow any pooling behavior on a per-application protocol basis.

   o  Adjust wording for external port allocation rate limiting.

   o  Add requirement for RFC4008 support (SHOULD level).

   o  Adjust wording for swapping address pools when rebooting.

   o  Add DSCP requirement (stolen from draft-jennings-behave-nat6).

   o  Add informative reference to
      draft-boucadair-intarea-nat-reveal-analysis.

   o  Add requirement for hold-down pool.

   o  Change definition of CGN.

   o  Avoid usage of "device" loaded word throughout the document.

   o  Add requirement about resource exhaustion.

   o  Change title.

   o  Describe additional CGN topology where there is no NAT444.

   o  Better justification for "Paired" pool behavior.

   o  Make it clear that rate limiting allocation is for preserving CPU
      resources

   o  Generalize the requirement for limiting the number of TCP sessions
      per mapping so that it applies to all memory-consuming state
      elements.




Perreault, et al.         Expires June 2, 2012                 [Page 16]


Internet-Draft              CGN Requirements               November 2011


   o  Change CPE to subscriber where it applies throughout the text.

   o  Better terminology for bulk port allocation mechanisms.

   o  Explain how external address pairing works with DS-Lite.

A.5.  Changed in -01

   o  Terminology: LSN is now CGN.

   o  Imported all requirements from RFCs 4787, 5382, and 5508.  This
      allowed us to eliminate some duplication.

   o  Added references to
      draft-ietf-intarea-server-logging-recommendations and
      draft-ford-shared-addressing-issues.

   o  Incorporated a requirement from
      draft-xu-behave-stateful-nat-standby-06.


Authors' Addresses

   Simon Perreault (editor)
   Viagenie
   2875 boul. Laurier, suite D2-630
   Quebec, QC  G1V 2M2
   Canada

   Phone: +1 418 656 9254
   Email: simon.perreault@viagenie.ca
   URI:   http://www.viagenie.ca


   Ikuhei Yamagata
   NTT Communications Corporation
   Gran Park Tower 17F, 3-4-1 Shibaura, Minato-ku
   Tokyo  108-8118
   Japan

   Phone: +81 50 3812 4704
   Email: ikuhei@nttv6.jp









Perreault, et al.         Expires June 2, 2012                 [Page 17]


Internet-Draft              CGN Requirements               November 2011


   Shin Miyakawa
   NTT Communications Corporation
   Gran Park Tower 17F, 3-4-1 Shibaura, Minato-ku
   Tokyo  108-8118
   Japan

   Phone: +81 50 3812 4695
   Email: miyakawa@nttv6.jp


   Akira Nakagawa
   Japan Internet Exchange Co., Ltd. (JPIX)
   Otemachi Building 21F, 1-8-1 Otemachi, Chiyoda-ku
   Tokyo  100-0004
   Japan

   Phone: +81 90 9242 2717
   Email: a-nakagawa@jpix.ad.jp


   Hiroyuki Ashida
   IS Consulting G.K.
   12-17 Odenma-cho Nihonbashi Chuo-ku
   Tokyo  103-0011
   Japan

   Email: assie@hir.jp
























Perreault, et al.         Expires June 2, 2012                 [Page 18]