BESS Working Group R. Singh
INTERNET-DRAFT K. Kompella
Intended Status: Proposed Standard Juniper Networks
Updates: 4761 (if approved) S. Palislamovic
Alcatel-Lucent
Expires: February 18, 2019 August 17, 2018
Updated processing of control flags for BGP VPLS
draft-ietf-bess-bgp-vpls-control-flags-06
Abstract
This document updates the meaning of the "control flags" fields
inside the "layer2 info extended community" used for BGP-VPLS NLRI as
defined in RFC4761. If approved, this document updates RFC4761.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Copyright and License Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Singh, et al Expires February 18, 2019 [Page 1]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Updated meaning of control flags in the layer2 info extended
community . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Control word (C-bit) . . . . . . . . . . . . . . . . . . . . 4
3.2 Sequence flag (S-bit) . . . . . . . . . . . . . . . . . . . 4
4 Using p2mp LSP as transport for BGP VPLS . . . . . . . . . . . 5
5 Treatment of C and S bits in multi-homing scenarios . . . . . . 5
5.1 Control word (C-bit) . . . . . . . . . . . . . . . . . . . . 5
5.2 Sequence flag (S-bit) . . . . . . . . . . . . . . . . . . . 6
6 Illustrative diagram . . . . . . . . . . . . . . . . . . . . . 6
7 Security Considerations . . . . . . . . . . . . . . . . . . . . 7
8 IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 7
9 References . . . . . . . . . . . . . . . . . . . . . . . . . . 7
9.1 Normative References . . . . . . . . . . . . . . . . . . . 7
9.2 Informative References . . . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 8
Singh, et al Expires February 18, 2019 [Page 2]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
1 Introduction
"Virtual Private LAN Service (VPLS) Using BGP for Auto-Discovery and
Signaling" ([RFC4761]) describes the concepts and signaling for using
BGP (Border Gateway Protocol) to setup a VPLS (virtual private LAN
service). It specifies the BGP VPLS NLRI (network layer reachability
information) by which a PE may require other PEs in the same VPLS to
include (or not) control-word and sequencing information in VPLS
frames sent to this PE.
The use of control word (CW) helps prevent mis-ordering of IPv4 or
IPv6 PW traffic over ECMP (equal cost multi-path) paths or LAG (link
aggregation group) bundles. [RFC4385] describes the format for
control-word that may be used over point-2-point PWs (pseudowires)
and over a VPLS. It along with [RFC3985] also describes sequencing of
frames.
However, [RFC4761] does not specify the behavior of PEs in a mixed
environment where some PEs support control-word/sequencing and others
do not.
1.1 Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2 Problem
[RFC4761] specifies the VPLS BGP NLRI by which a given PE advertises
the behavior expected from the multiple PEs participating in the same
VPLS. The NLRI indicates the VPLS label that the various PE routers,
which are referred to in the NLRI, should use when forwarding VPLS
traffic to this PE. Additionally, by using the "control flags" this
PE specifies whether the other PEs (in the same VPLS) should use
control-word or sequenced-delivery for frames forwarded to this PE.
These are respectively indicated by the C and the S bits in the
"control flags" as specified in section 3.2.4 in [RFC4761].
[RFC4761] requires that if the advertising PE sets the C and S bits,
when forwarding VPLS traffic to the PE, the receiving PE MUST insert
control word (CW) and by including sequence numbers respectively.
However, in a BGP VPLS deployment there would often be cases where a
PE receiving the VPLS BGP NLRI may not have the ability to insert a
CW or include sequencing information inside PW frames. Thus, the
behavior of processing CW and sequencing needs to be further
specified.
Singh, et al Expires February 18, 2019 [Page 3]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
This document updates the meaning of the control flags in layer2
extended community in the BGP VPLS NLRI. It also specifies the
forwarding behavior for a mixed-mode environment where not every PE
in a VPLS has the ability or the configuration to honor the control
flags received from the PE advertising the BGP NLRI.
3 Updated meaning of control flags in the layer2 info extended
community
Current specification does not allow for the CW setting to be
negotiated. Rather, if a PE sets the C-bit, it expects to receive
VPLS frames with a control word, and will send frames the same way.
If the PEs at both ends of a pseudowire do not agree on the setting
of the C-bit, the PW does not come up. The expected behavior is
similar for the S-bit.
This memo updates the meaning of the C-bit and the S-bit in the
control flags.
3.1 Control word (C-bit)
If a PE sets the C-bit in its NLRI, it means that the PE has ability
to send and receive frames with a control word. If the PEs at both
ends of a PW set the C-bit, control words MUST be used in both
directions of the PW. If both PEs send a C-bit of 0, control words
MUST NOT be used on the PW. These two cases behave as before.
However, if the PEs don't agree on the setting of the C-bit, control
words MUST NOT be used on that PW but the PW MUST NOT be prevented
from coming up due to this mismatch. So, the PW MUST still come up.
This behavior is new; the old behavior was that the PW doesn't come
up.
3.2 Sequence flag (S-bit)
Current BGP VPLS specification do not allow for S-bit setting to be
negotiated either. If the PE sets the S-bit, it expects to receive
VPLS frames with sequence numbers, and will send the frames with
sequence numbers as well. This memo further specifies the existing
behavior. If the PEs on the both ends of the PW set the S-bit, then
both PEs MUST include the PW sequence numbers. If the PEs at both
ends of the PW do not agree on the setting of the S-bit, the PW
SHOULD NOT come up at all.
Singh, et al Expires February 18, 2019 [Page 4]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
4 Using p2mp LSP as transport for BGP VPLS
BGP VPLS can be used over point-2-point LSPs acting as transport
between the VPLS PEs. Alternately, BGP VPLS may also be used over
p2mp (point to multipoint) LSPs (label switched path) with the source
of the p2mp LSP rooted at the PE advertising the VPLS BGP NLRI.
In a network that uses p2mp LSPs as transport for BGP VPLS, in a
given VPLS there may be some PEs that support control-word while
others do not. Similarly, for sequencing of frames.
In such a setup, a source PE that supports control-word should setup
2 different p2mp LSPs such that:
- one p2mp LSP will carry CW-marked frames to those PEs that
advertised C-bit as 1, and
- the other p2mp LSP will carry frames without CW to those PEs
that advertised C-bit as 0.
Using 2 different p2mp LSPs to deliver frames with and without CW
to different PEs ensures that this PE honors the C-bit advertised
by the other PEs.
However, the set of leaves on the 2 p2mp LSPs (rooted at the given
PE) MUST NOT contain any PEs that advertised a value for S-bit
different from what this PE itself is advertising. PEs that
advertised their S-bit value differently (from what this PE
advertised) will not be on either of the p2mp LSPs. It is ensured
that this PE is sending VPLS frames only to those PEs that agree
with this PE on the setting of S-bit.
5 Treatment of C and S bits in multi-homing scenarios
5.1 Control word (C-bit)
In multi-homed environment, different PEs may effectively represent
the same service destination end point. It could be assumed that
the end-to-end PW establishment process should follow the same
rules when it comes to control word requirement, meaning setting
the C-bit would be enforced equally toward both primary and backup
designated forwarder together.
However, in the multi-homing case each PW SHOULD be evaluated
independently. Assuming the below specified network topology, there
could be the case where PW between PE2 and PE1 could have control
word signaled via extended community and would be used in the VPLS
frame, while PE2 to PE4 PW would not insert the control word in the
VPLS frame due to C-bit mismatch. The rest of PEs multi-homing
behavior should simply follow the rules specified in draft-ietf-
Singh, et al Expires February 18, 2019 [Page 5]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
bess-vpls-multihoming-00.
5.2 Sequence flag (S-bit)
In multi-homed environment, different PEs may effectively represent
the same service destination end point. In this case, the rules for
end-to-end PW establishment SHOULD follow the same rules when it
comes to sequence bit requirements. Consider the case below with
CE5 being multi-homed to PE4 and PE1. The PW behavior is similar
to the C-word scenario so that the insertion of S-bit evaluation
SHOULD be independent per PW. However, because S-bit mismatch
between two end-point PEs yields in no PW establishment, in the
case where PE4 doesn't support S-bit, only one PW would be
established, between PE1 and PE2. Thus, even though CE5 is
physically multi-homed, due to PE4's lack of support for S-bit, and
no PW between PE1 and PE4, CE5 would not be multi-homed any more.
6 Illustrative diagram
-----
/ A1 \
---- ____CE1 |
/ \ -------- -------- / | |
| A2 CE2- / \ / PE1 \ /
\ / \ / \___/ | \ -----
---- ---PE2 | \
| | \ -----
| Service Provider Network | \ / \
| | CE5 A5
| ___ | / \ /
\ / \ PE4_/ -----
PE3 / \ /
|------/ \------- -------
---- / | ----
/ \/ \ / \ CE = Customer Edge Device
| A3 CE3 --CE4 A4 | PE = Provider Edge Router
\ / \ /
---- ---- A<n> = Customer site n
Figure 1: Example of a VPLS
In the above topology, let there be a VPLS configured with the PEs as
displayed. Let PE1 be the PE under consideration that is CW enabled.
Let PE2 and PE3 also be CW enabled. Let PE4 not be CW enabled. PE1
will advertise a VPLS BGP NLRI, containing the C/S bits marked as 1.
PE2 and PE3 on learning of NLRI from PE1, shall include the control
Singh, et al Expires February 18, 2019 [Page 6]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
word in VPLS frames being forwarded to PE1. However, PE4 which does
not have the ability to include control-word.
As per [RFC4761], PE1 would have an expectation that all other PEs
forward traffic to it by including CW. That expectation cannot be met
by PE4 in this example. Thus, as per [RFC4761] the PW between PE1 and
PE4 does not come up.
However, this document addresses how to support the mixed-CW
environment as above. PE1 will bring up the PW with PE4 despite the
CW mismatch. Additionally, it will setup its data-plane such that it
will strip the control-word only for those VPLS frames that are
received from PEs that are themselves indicating their desire to
receive CW marked frames. So, PE1 will setup its data plane to strip-
off the CW only for VPLs frames received from PEs PE2 and PE3. PE1
will setup its data plane to not strip CW from frames received from
PE4.
7 Security Considerations
This document updates the behavior specified in [RFC4761]. The
security considerations listed in [RFC4761] apply. However, there are
no new security considerations due to the text of this document.
8 IANA Considerations
This document does not make any requests from IANA.
9 References
9.1 Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4761] Kompella, K., Y. Rekhter, Virtual Private LAN Service
(VPLS) Using BGP for Auto-Discovery and Signaling,
RFC 4761, January 2007.
[RFC4385] Bryant, S., Swallow G., Martini L., D. McPherson,
Pseudowire Emulation Edge-to-Edge (PWE3) Control Word,
RFC 4385, February 2006.
9.2 Informative References
[RFC3985] Bryant, S., P. Pate, Pseudo Wire Emulation
Edge-to-Edge (PWE3) Architecture, RFC3985, March 2005.
Singh, et al Expires February 18, 2019 [Page 7]
INTERNET DRAFT Control Flags for BGP VPLS August 17, 2018
Authors' Addresses
Ravi Singh
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
EMail: ravis@juniper.net
Kireeti Kompella
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
EMail: kireeti@juniper.net
Senad Palislamovic
Alcatel-Lucent
EMail: senad.palislamovic@alcatel-lucent.com
Singh, et al Expires February 18, 2019 [Page 8]