Internet Engineering Task Force N. Akiya
Internet-Draft Big Switch Networks
Intended status: Standards Track C. Pignataro
Expires: October 15, 2016 D. Ward
Cisco Systems
April 13, 2016
Seamless Bidirectional Forwarding Detection (S-BFD) for
IPv4, IPv6 and MPLS
draft-ietf-bfd-seamless-ip-04
Abstract
This document defines procedures to use Seamless Bidirectional
Forwarding Detection (S-BFD) for IPv4, IPv6 and MPLS environments.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 15, 2016.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Akiya, et al. Expires October 15, 2016 [Page 1]
Internet-Draft Seamless BFD for IP April 2016
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. S-BFD UDP Port . . . . . . . . . . . . . . . . . . . . . . . 2
3. S-BFD Echo UDP Port . . . . . . . . . . . . . . . . . . . . . 3
4. S-BFD Control Packet Demultiplexing . . . . . . . . . . . . . 3
5. Initiator Procedures . . . . . . . . . . . . . . . . . . . . 3
5.1. Details of S-BFD Control Packet Sent by SBFDInitiator . . 4
5.1.1. Target vs. Remote Entity (S-BFD Discriminator) . . . 4
6. Responder Procedures . . . . . . . . . . . . . . . . . . . . 5
6.1. Details of S-BFD Control Packet Sent by SBFDReflector . . 5
7. Security Considerations . . . . . . . . . . . . . . . . . . . 5
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 6
10. Contributing Authors . . . . . . . . . . . . . . . . . . . . 6
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
11.1. Normative References . . . . . . . . . . . . . . . . . . 7
11.2. Informative References . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
Seamless Bidirectional Forwarding Detection (S-BFD),
[I-D.ietf-bfd-seamless-base], defines a generalized mechanism to
allow network nodes to seamlessly perform continuity checks to remote
entities. This document defines necessary procedures to use S-BFD on
IPv4, IPv6 and MPLS environments.
The reader is expected to be familiar with the IP [RFC0791]
[RFC2460], BFD [RFC5880], MPLS BFD [RFC5884], and S-BFD
[I-D.ietf-bfd-seamless-base] terminologies and protocol constructs.
2. S-BFD UDP Port
A new UDP port is defined for the use of the S-BFD on IPv4, IPv6 and
MPLS environments: 7784. SBFDReflector session MUST listen for
incoming S-BFD control packets on the port 7784. SBFDInitiator
sessions MUST transmit S-BFD control packets with destination port
7784. The source port of the S-BFD control packets transmitted by
SBFDInitiator sessions can be any but MUST NOT be 7784. The same UDP
source port number MUST be used for all S-BFD control packets
Akiya, et al. Expires October 15, 2016 [Page 2]
Internet-Draft Seamless BFD for IP April 2016
associated with a particular SBFDInitiator session. The source port
number is unique among all SBFDInitiator sessions on the system.
3. S-BFD Echo UDP Port
The BFD Echo port defined by [RFC5881], port 3785, is used for the
S-BFD Echo function on IPv4, IPv6 and MPLS environments.
SBFDInitiator sessions MUST transmit S-BFD echo packets with
destination port 3785. This document defines only the UDP port value
for the S-BFD Echo function. The source port and the procedures for
the S-BFD Echo function are outside the scope of this document.
4. S-BFD Control Packet Demultiplexing
The S-BFD Control Packet demultiplexing follows the procedure
specified in Section 7.1. of [I-D.ietf-bfd-seamless-base]. Received
S-BFD control packet MUST be demultiplexed with the destination UDP
port field.
This procedure for an S-BFD packet is executed on both the initiator
and the reflector. If the port is 7784 (i.e., S-BFD packet for
S-BFDReflector)), then the packet MUST be looked up to locate a
corresponding SBFDReflector session based on the value from the "your
discriminator" field in the table describing S-BFD discriminators.
If the port is not 7784, then the packet MUST be looked up to locate
a corresponding SBFDInitiator session or classical BFD session based
on the value from the "your discriminator" field in the table
describing BFD discriminators. If the located session is an
SBFDInitiator, then the destination IP address of the packet SHOULD
be validated to be for self. If the packet is a classical BFD
session, then the procedures from [RFC5880] apply.
5. Initiator Procedures
S-BFD control packets are transmitted with IP header, UDP header and
BFD control header ([RFC5880]). When S-BFD control packets are
explicitly label switched (i.e. not IP routed which happen to go over
an LSP, but explicitly sent on a specific LSP), the former is
prepended with a label stack. Note that this document does not make
a distinction between a single-hop S-BFD scenario and a multi-hop
S-BFD scenario, both scenarios are supported.
Necessary values in the BFD control headers are described in
[I-D.ietf-bfd-seamless-base]. Section 5.1 describes necessary values
in the MPLS header, IP header and UDP header when an SBFDInitiator on
the initiator is sending S-BFD control packets.
Akiya, et al. Expires October 15, 2016 [Page 3]
Internet-Draft Seamless BFD for IP April 2016
5.1. Details of S-BFD Control Packet Sent by SBFDInitiator
o Specifications common to both IP routed S-BFD control packets and
explicitly label switched S-BFD control packets:
* Source IP address field of the IP header MUST be set to a local
IP address that is expected to be routable by the target (i.e.
not IPv6 link-local address when the target is multiple hops
away).
* UDP destination port MUST be set to a well-known UDP
destination port assigned for S-BFD: 7784.
* UDP source port MUST NOT be set to 7784.
o Specifications for IP routed S-BFD control packets:
* Destination IP address field of the IP header MUST set to an IP
address of the target.
* TTL field of the IP header SHOULD be set to 255.
o Specifications for explicitly label switched S-BFD control
packets:
* S-BFD control packets MUST have the label stack that is
expected to reach the target.
* TTL field of the top most label SHOULD be 255.
* The destination IP address MUST be chosen from the 127/8 range
for IPv4 and from the 0:0:0:0:0:FFFF:7F00/104 range for IPv6,
as with [RFC5884].
* TTL field of the IP header MUST be set to 1.
5.1.1. Target vs. Remote Entity (S-BFD Discriminator)
Typically, an S-BFD control packet will have "your discriminator"
field corresponding to an S-BFD discriminator of the remote entity
located on the target network node defined by the destination IP
address or the label stack. It is, however, possible for an
SBFDInitiator to carefully set "your discriminator" and TTL fields to
perform a continuity test towards a target, but to a transit network
node and not to the target itself.
Section 5.1 intentionally uses the word "target", instead of "remote
entity", to accommodate this possible S-BFD usage through TTL expiry.
Akiya, et al. Expires October 15, 2016 [Page 4]
Internet-Draft Seamless BFD for IP April 2016
This also requires S-BFD control packets not be dropped by the
responder node due to TTL expiry. Thus implementations on the
responder MUST allow received S-BFD control packets taking TTL expiry
exception path to reach corresponding reflector BFD session.
6. Responder Procedures
S-BFD control packets are IP routed back to the initiator, and will
have IP header, UDP header and BFD control header. If an
SBFDReflector receives an S-BFD control packet with UDP source port
as 7784, the packet MUST be discarded. Necessary values in the BFD
control header are described in [I-D.ietf-bfd-seamless-base].
Section 6.1 describes necessary values in the IP header and UDP
header when an SBFDReflector on the responder is sending S-BFD
control packets.
6.1. Details of S-BFD Control Packet Sent by SBFDReflector
o Destination IP address field of the IP header MUST be copied from
source IP address field of received S-BFD control packet.
o Source IP address field of the IP header MUST be set to a local IP
address that is expected to be visible by the initiator (i.e. not
IPv6 link-local address when the initiator is multiple hops away).
The source IP address SHOULD be copied from the destination IP
address field of the received S-BFD control packet, except when it
is from the 127/8 range for IPv4 or from the
0:0:0:0:0:FFFF:7F00/104 range for IPv6.
o TTL field of the IP header MUST be set to 255.
o UDP destination port MUST be copied from received UDP source port.
o UDP source port MUST be copied from received UDP destination port.
7. Security Considerations
Security considerations for S-BFD are discussed in
[I-D.ietf-bfd-seamless-base]. Additionally, implementing the
following measures will strengthen security aspects of the mechanism
described by this document:
o Implementations MUST provide filtering capability based on source
IP addresses of received S-BFD control packets: [RFC2827].
o Implementations MUST NOT act on received S-BFD control packets
containing source Martian IP addresses (i.e., address that, by
Akiya, et al. Expires October 15, 2016 [Page 5]
Internet-Draft Seamless BFD for IP April 2016
application of the current forwarding tables, would not have its
return traffic routed back to the sender.)
o Implementations MUST ensure that response S-BFD control packets
generated to the initiator by the SBFDReflector have a reachable
target (ex: destination IP address).
8. IANA Considerations
A new value 7784 was allocated from the "Service Name and Transport
Protocol Port Number Registry". The allocated registry entry is:
Service Name (REQUIRED)
s-bfd
Transport Protocol(s) (REQUIRED)
udp
Assignee (REQUIRED)
IESG <iesg@ietf.org>
Contact (REQUIRED)
BFD Chairs <bfd-chairs@tools.ietf.org>
Description (REQUIRED)
Seamless Bidirectional Forwarding Detection (S-BFD)
Reference (REQUIRED)
RFC.this (RFC Editor, please update at publication)
Port Number (OPTIONAL)
7784
9. Acknowledgements
The authors would like to thank the BFD WG members for helping to
shape the contents of this document. In particular, significant
contributions were made by following people: Marc Binderberger,
Jeffrey Haas, Santosh Pallagatti, Greg Mirsky, Sam Aldrin, Vengada
Prasad Govindan, Mallik Mudigonda and Srihari Raghavan.
10. Contributing Authors
Tarek Saad
Cisco Systems
Email: tsaad@cisco.com
Siva Sivabalan
Cisco Systems
Email: msiva@cisco.com
Nagendra Kumar
Cisco Systems
Email: naikumar@cisco.com
Akiya, et al. Expires October 15, 2016 [Page 6]
Internet-Draft Seamless BFD for IP April 2016
11. References
11.1. Normative References
[I-D.ietf-bfd-seamless-base]
Akiya, N., Pignataro, C., Ward, D., Bhatia, M., and J.
Networks, "Seamless Bidirectional Forwarding Detection
(S-BFD)", draft-ietf-bfd-seamless-base-08 (work in
progress), February 2016.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
<http://www.rfc-editor.org/info/rfc5880>.
[RFC5881] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881,
DOI 10.17487/RFC5881, June 2010,
<http://www.rfc-editor.org/info/rfc5881>.
11.2. Informative References
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
DOI 10.17487/RFC0791, September 1981,
<http://www.rfc-editor.org/info/rfc791>.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
December 1998, <http://www.rfc-editor.org/info/rfc2460>.
[RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP Source
Address Spoofing", BCP 38, RFC 2827, DOI 10.17487/RFC2827,
May 2000, <http://www.rfc-editor.org/info/rfc2827>.
[RFC5884] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,
"Bidirectional Forwarding Detection (BFD) for MPLS Label
Switched Paths (LSPs)", RFC 5884, DOI 10.17487/RFC5884,
June 2010, <http://www.rfc-editor.org/info/rfc5884>.
Akiya, et al. Expires October 15, 2016 [Page 7]
Internet-Draft Seamless BFD for IP April 2016
Authors' Addresses
Nobo Akiya
Big Switch Networks
Email: nobo.akiya.dev@gmail.com
Carlos Pignataro
Cisco Systems
Email: cpignata@cisco.com
Dave Ward
Cisco Systems
Email: wardd@cisco.com
Akiya, et al. Expires October 15, 2016 [Page 8]