Internet Draft E.L. Bell
Expires September 1999 3Com Corp.
draft-ietf-bridge-bridgemib-05.txt A. Smith
Extreme Networks
P. Langille
Newbridge Networks
A. Rijhsinghani
Cabletron Systems
K. McCloghrie
cisco Systems
March 1999
Definitions of Managed Objects for Bridges with Traffic
Classes, Multicast Filtering and Virtual LAN Extensions
Status of this Memo
This document is an Internet Draft and is in full conformance with all
provisions of Section 10 of RFC2026. Internet Drafts are working
documents of the Internet Engineering Task Force (IETF), its Areas, and
its Working Groups. Note that other groups may also distribute working
documents as Internet Drafts.
Internet Drafts are draft documents valid for a maximum of six months.
Internet Drafts may be updated, replaced, or obsoleted by other
documents at any time. It is not appropriate to use Internet Drafts as
reference material or to cite them other than as a "working draft" or
"work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This document is a product of the IETF's Bridge MIB Working Group.
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB) for
use with network management protocols in TCP/IP based internets. In
particular it defines objects for managing MAC bridges based on the IEEE
802.1D-1998 MAC Bridges and IEEE 802.1Q-1998 Virtual LAN (VLAN)
standards for bridging between Local Area Network (LAN) segments.
Bell, et al. Expires September 1999 [Page 1]
Internet Draft Bridge MIB Extensions March 1999
Provisions are made for support of transparent bridging. Provisions are
also made so that these objects apply to bridges connected by
subnetworks other than LAN segments. This memo also includes several
MIB modules in a manner that is compliant to the SNMPv2 SMI [5].
1. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2271 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [2], RFC 1212 [3] and RFC 1215 [4]. The second
version, called SMIv2, is described in RFC 1902 [5], RFC 1903
[6] and RFC 1904 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [8]. A second version of the SNMP message
protocol, which is not an Internet standards track protocol, is
called SNMPv2c and described in RFC 1901 [9] and RFC 1906 [10].
The third version of the message protocol is called SNMPv3 and
described in RFC 1906 [10], RFC 2272 [11] and RFC 2274 [12].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [8]. A second set of protocol operations
and associated PDU formats is described in RFC 1905 [13].
o A set of fundamental applications described in RFC 2273 [14] and
the view-based access control mechanism described in RFC 2275
[15].
Managed objects are accessed via a virtual information store, termed the
Management Information Base or MIB. Objects in the MIB are defined
using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A MIB
conforming to the SMIv1 can be produced through the appropriate
Bell, et al. Expires September 1999 [Page 2]
Internet Draft Bridge MIB Extensions March 1999
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
Bell, et al. Expires September 1999 [Page 3]
Internet Draft Bridge MIB Extensions March 1999
2. Overview
A common device present in many networks is the Bridge. This device is
used to connect Local Area Network segments below the network layer.
These devices are often known as 'layer 2 switches'.
There are two major modes defined for this bridging; transparent and
source route. The transparent method of bridging is defined by IEEE
802.1D-1998 [19]. Managed objects for source route bridges are defined
in [23].
IEEE 802.1D is augmented by IEEE 802.1Q-1998 [20] to provide support for
'virtual bridged LANs' where a single bridged physical LAN network may
be used to support multiple logical bridged LANs, each of which offers a
service approximately the same as that defined by 802.1D. Such virtual
LANs (VLANs) are an integral feature of switched LAN networks. A VLAN
can be viewed as a group of end-stations on multiple LAN segments and
can communicate as if they were on a single LAN. IEEE 802.1Q defines
port-based Virtual LANs where membership is determined by the bridge
port on which data frames are received. This memo defines the objects
needed for the management of port-based VLANs in bridge entities.
This memo defines those objects needed for the management of a bridging
entity operating in the transparent mode, as well as some objects
applicable to all types of bridges. Managed objects for Source-Routing
are defined in [23].
2.1. Scope
This MIB includes a comprehensive set of managed objects which attempts
to match the set defined in IEEE 802.1D and IEEE 802.1Q. However, to be
consistent with the spirit of the SNMP Framework, a subjective judgement
was made to omit the objects from those standards most 'costly' to
implement in an agent and least 'essential' for fault and configuration
management. The omissions are described in section 3 below.
Historical note:
RFC 1493 used the following principles for determining inclusion of an
object in the BRIDGE-MIB module:
(1) Start with a small set of essential objects and add only as
further objects are needed.
Bell, et al. Expires September 1999 [Page 4]
Internet Draft Bridge MIB Extensions March 1999
(2) Require objects be essential for either fault or configuration
management.
(3) Consider evidence of current use and/or utility.
(4) Limit the total of objects.
(5) Exclude objects which are simply derivable from others in this or
other MIBs.
(6) Avoid causing critical sections to be heavily instrumented. The
guideline that was followed is one counter per critical section
per layer.
3. Structure of MIBs
This document defines additional objects, on top of those existing in
the base BRIDGE-MIB module defined in RFC1493: that MIB module is
maintained unchanged for backwards compatibility. Section 3.4.3 of the
present document contains some recommendations regarding usage of
objects in RFC1493 by devices implementing the enhancements defined
here.
Two MIB modules are defined here:
(1) Managed objects for an extended bridge MIB module P-BRIDGE-MIB
for the traffic class and multicast filtering enhancements
defined by IEEE 802.1D-1998.
(2) Managed objects for a virtual bridge MIB module Q-BRIDGE-MIB for
the Virtual LAN bridging enhancements defined by IEEE
802.1Q-1998.
3.1. Structure of Extended Bridge MIB module
Objects in this MIB are arranged into groups. Each group is organized
as a set of related objects. The overall structure and assignment of
objects to their groups is shown below.
Bell, et al. Expires September 1999 [Page 5]
Internet Draft Bridge MIB Extensions March 1999
3.1.1. Relationship to IEEE 802.1D-1998 Manageable Objects
This section contains a cross-reference to the objects defined in IEEE
802.1D-1998 [19]. It also details those objects that are not considered
necessary in this MIB module.
Some objects defined by [19] have been included in the virtual bridge
MIB module rather than this one: entries in dot1qTpGroupTable,
dot1qForwardAllTable and dot1qForwardUnregisteredTable are required for
virtual bridged LANs with additional indexing (e.g. per-VLAN, per-FDB)
and so are not defined here. Instead, devices which do not implement
virtual bridged LANs, should implement these tables with a fixed value
for dot1qFdbId (the value 1 is recommended) or dot1qVlanIndex (the value
1 is recommended). Devices which support Extended Filtering Services
(dynamic learning of Multicast Group Addresses and Group Service
Requirements in the Filtering Database) should support
dot1qTpGroupTable, dot1qForwardAllTable and
dot1qForwardUnregisteredTable.
Extended Bridge MIB Name IEEE 802.1D Name
dot1dExtended Bridge
dot1dExtBase
dot1dDeviceCapabilities
dot1dExtendedFilteringServices
dot1dTrafficClasses
dot1dTrafficClassesEnabled
dot1dGmrpStatus .ApplicantAdministrativeControl
dot1dPriority
dot1dPortPriorityTable
dot1dPortDefaultUserPriority .UserPriority
dot1dPortNumTrafficClasses
dot1dUserPriorityRegenTable .UserPriorityRegenerationTable
dot1dUserPriority
dot1dRegenUserPriority
dot1dTrafficClassTable .TrafficClassTable
dot1dTrafficClassPriority
dot1dTrafficClass
dot1dPortOutboundAccessPriorityTable
.OutboundAccessPriorityTable
dot1dPortOutboundAccessPriority
dot1dGarp
dot1dPortGarpTable
dot1dPortGarpJoinTime .JoinTime
dot1dPortGarpLeaveTime .LeaveTime
Bell, et al. Expires September 1999 [Page 6]
Internet Draft Bridge MIB Extensions March 1999
dot1dPortGarpLeaveAllTime .LeaveAllTime
dot1dGmrp
dot1dPortGmrpTable
dot1dPortGmrpStatus .ApplicantAdministrativeControl
dot1dPortGmrpFailedRegistrations
.FailedRegistrations
dot1dPortGmrpLastPduOrigin .OriginatorOfLastPDU
dot1dTpGroup
dot1dTpHCPortTable
dot1dTpHCPortInFrames .BridgePort.FramesReceived
dot1dTpHCPortOutFrames .ForwardOutBound
dot1dTpHCPortInDiscards .DiscardInbound
dot1dTpPortOverflowTable
dot1dTpPortInOverflowFrames .BridgePort.FramesReceived
dot1dTpPortOutOverflowFrames .ForwardOutBound
dot1dTpPortInOverflowDiscards .DiscardInbound
The following IEEE 802.1D management objects have not been included in
the Bridge MIB for the indicated reasons.
IEEE 802.1D Object Disposition
Bridge.StateValue not considered useful
Bridge.ApplicantAdministrativeControl
not provided per-attribute
(e.g. per-VLAN, per-Group).
Only per-{device,port,application}
control is provided in this MIB.
3.1.2. Relationship to IEEE 802.1Q Manageable Objects
This section contains a cross-reference to the objects defined in IEEE
802.1Q-1998 [20]. These objects have been included in this MIB as they
provide a natural fit with the 802.1D objects they are located with.
Extended Bridge MIB Name IEEE 802.1Q Name
dot1dExtended Bridge
dot1dExtBase
dot1dDeviceCapabilities
dot1qStaticEntryIndividualPort 5.2 implementation options
dot1qIVLCapable
dot1qSVLCapable
dot1qHybridCapable
Bell, et al. Expires September 1999 [Page 7]
Internet Draft Bridge MIB Extensions March 1999
dot1qConfigurablePvidTagging 12.10.1.1 read bridge vlan
config
dot1dPortCapabilitiesTable
dot1dPortCapabilities
dot1qDot1qTagging 5.2 implementation options
dot1qConfigurableAcceptableFrameTypes
5.2 implementation options
dot1qIngressFiltering 5.2 implementation options
3.1.3. The dot1dExtBase Group
This group contains the objects which are applicable to all bridges
implementing the traffic class and multicast filtering features of
802.1D. It includes per-device configuration of GARP and GMRP
protocols. This group will be implemented by all devices which
implement the extensions defined in 802.1D-1998.
3.1.4. The dot1dPriority Group
This group contains the objects for configuring and reporting status of
priority-based queuing mechanisms in a bridge. This includes per- port
user_priority treatment, mapping of user_priority in frames into
internal traffic classes and outbound user_priority and access_priority.
3.1.5. The dot1dGarp Group
This group contains the objects for configuring and reporting on
operation of the Generic Attribute Registration Protocol (GARP).
3.1.6. The dot1dGmrp Group
This group contains the objects for configuring and reporting on
operation of the GARP Multicast Registration Protocol (GMRP).
3.1.7. The dot1dHCPortTable
This table extends the dot1dTp group from RFC1493 and contains the
objects for reporting port bridging statistics for high-capacity network
interfaces.
Bell, et al. Expires September 1999 [Page 8]
Internet Draft Bridge MIB Extensions March 1999
3.2. Structure of Virtual Bridge MIB module
Objects in this MIB are arranged into groups. Each group is organized
as a set of related objects. The overall structure and assignment of
objects to their groups is shown below. Some of the original objects
from RFC1493 need to be indexed differently when extended in a VLAN
environment so some objects in that module effectively duplicate new
objects defined here: this is necessary for backwards compatibility.
3.2.1. Relationship to IEEE 802.1Q Manageable Objects
This section contains a cross-reference to the objects defined in [20].
It also details those objects that are not considered necessary in this
MIB module.
Note: unlike IEEE 802.1D, [20] chose not to define a new set of managed
object names so those following are referenced from the descriptions of
management operations with section numbering from clause 12 in that
document.
Virtual Bridge MIB object 802.1Q object
dot1qBase
dot1qVlanVersionNumber 12.10.1.1 read bridge vlan config
dot1qMaxVlanId 12.10.1.1 read bridge vlan config
dot1qMaxSupportedVlans 12.10.1.1 read bridge vlan config
dot1qNumVlans
dot1dGvrpStatus 12.9.2.1/2 read/set garp
applicant controls
dot1qTp
dot1qFdbTable
dot1qFdbId
dot1qFdbDynamicCount 12.7.1.1.3 read filtering d/base
dot1qTpFdbTable
dot1qTpFdbAddress
dot1qTpFdbPort
dot1qTpFdbStatus
dot1qTpGroupTable 12.7.7.1 read filtering entry
dot1qTpGroupAddress
dot1qTpGroupEgressPorts
dot1qTpGroupLearnt
dot1qForwardAllTable 12.7.7.1 read filtering entry
dot1qForwardAllPorts
dot1qForwardAllStaticPorts
Bell, et al. Expires September 1999 [Page 9]
Internet Draft Bridge MIB Extensions March 1999
dot1qForwardAllForbiddenPorts
dot1qForwardUnregisteredTable 12.7.7.1 read filtering entry
dot1qForwardUnregisteredPorts
dot1qForwardUnregisteredStaticPorts
dot1qForwardUnregisteredForbiddenPorts
dot1qStatic
dot1qStaticUnicastTable 12.7.7.1 create/delete/read
filtering entry
12.7.6.1 read permanent database
dot1qStaticUnicastAddress
dot1qStaticUnicastReceivePort
dot1qStaticUnicastAllowedToGoTo
dot1qStaticUnicastStatus
dot1qStaticMulticastTable 12.7.7.1 create/delete/read
filtering entry
12.7.6.1 read permanent database
dot1qStaticMulticastAddress
dot1qStaticMulticastReceivePort
dot1qStaticMulticastStaticEgressPorts
dot1qStaticMulticastForbiddenEgressPorts
dot1qStaticMulticastStatus
dot1qVlan
dot1qVlanNumDeletes
dot1qVlanCurrentTable 12.10.2.1 read vlan configuration
12.10.3.5 read VID to FID
allocations
12.10.3.6 read FID allocated to VID
12.10.3.7 read VIDs allocated to
FID
dot1qVlanTimeMark
dot1qVlanIndex
dot1qVlanFdbId
dot1qVlanCurrentEgressPorts
dot1qVlanCurrentUntaggedPorts
dot1qVlanStatus
dot1qVlanCreationTime
dot1qVlanStaticTable 12.7.7.1/2/3 create/delete/read
filtering entry
12.7.6.1 read permanent database
12.10.2.2 create vlan config
12.10.2.3 delete vlan config
dot1qVlanStaticName 12.4.1.3 set bridge name
dot1qVlanStaticEgressPorts
dot1qVlanForbiddenEgressPorts
dot1qVlanStaticUntaggedPorts
Bell, et al. Expires September 1999 [Page 10]
Internet Draft Bridge MIB Extensions March 1999
dot1qVlanStaticRowStatus
dot1qPortVlanConfigTable 12.10.1.1 read bridge vlan
configuration
dot1qPvid 12.10.1.2 configure PVID values
dot1qPortAcceptableFrameTypes 12.10.1.3 configure acceptable
frame types parameter
dot1qPortIngressFiltering 12.10.1.4 configure ingress
filtering parameters
dot1qPortGvrpStatus 12.9.2.2 read/set garp applicant
controls
dot1qPortGvrpFailedRegistrations
dot1qPortGvrpLastPduOrigin
dot1qPortVlanStatisticsTable 12.6.1.1 read forwarding port
counters
dot1qTpVlanPortInFrames
dot1qTpVlanPortOutFrames
dot1qTpVlanPortInDiscards
dot1qTpVlanPortInOverflowFrames
dot1qTpVlanPortOutOverflowFrames
dot1qTpVlanPortInOverflowDiscards
dot1qPortVlanHCStatisticsTable 12.6.1.1 read forwarding port
counters
dot1qTpVlanPortHCInFrames
dot1qTpVlanPortHCOutFrames
dot1qTpVlanPortHCInDiscards
dot1qLearningConstraintsTable 12.10.3.1/3/4 read/set/delete
vlan learning constraints
12.10.3.2 read vlan learning
constraints for VID
dot1qConstraintVlan
dot1qConstraintSet
dot1qConstraintType
dot1qConstraintStatus
dot1qConstraintSetDefault
dot1qConstraintTypeDefault
The following IEEE 802.1Q management objects have not been included in
the Bridge MIB for the indicated reasons.
IEEE 802.1Q Object Disposition
reset bridge (12.4.1.4) not considered useful
reset vlan bridge (12.10.1.5) not considered useful
Bell, et al. Expires September 1999 [Page 11]
Internet Draft Bridge MIB Extensions March 1999
read forwarding port counters (12.6.1.1)
discard on error details not considered useful
read permanent database (12.7.6.1)
permanent database size not considered useful
number of static filtering count rows in
entries dot1qStaticUnicastTable +
dot1qStaticMulticastTable
number of static VLAN count rows in
registration entries dot1qVlanStaticTable
read filtering entry range use GetNext operation.
(12.7.7.4)
read filtering database (12.7.1.1)
filtering database size not considered useful
number of dynamic group address count rows applicable to each
entries (12.7.1.3) FDB in dot1dTpGroupTable
read garp state (12.9.3.1) not considered useful
notify vlan registration failure not considered useful
(12.10.1.6)
notify learning constraint violation
(12.10.3.10) not considered useful
3.2.2. The dot1qBase Group
This mandatory group contains the objects which are applicable to all
bridges implementing 802.1Q virtual LANs.
3.2.3. The dot1qTp Group
This group contains objects that control the operation and report the
status of transparent bridging. This includes management of the dynamic
Filtering Databases for both unicast and multicast forwarding. This
group will be implemented by all bridges that perform destination-
address filtering.
Bell, et al. Expires September 1999 [Page 12]
Internet Draft Bridge MIB Extensions March 1999
3.2.4. The dot1qStatic Group
This group contains objects that control static configuration
information for transparent bridging. This includes management of the
static entries in the Filtering Databases for both unicast and multicast
forwarding.
3.2.5. The dot1qVlan Group
This group contains objects that control configuration and report status
of the Virtual LANs known to a bridge. This includes management of the
statically configured VLANs as well as reporting VLANs discovered by
other means e.g. GVRP. It also controls configuration and reports
status of per-port objects relating to VLANs and reports traffic
statistics. It also provides for management of the VLAN Learning
Constraints.
3.3. Textual Conventions
The datatypes MacAddress, BridgeId, Timeout, EnabledStatus, PortList,
VlanIndex and VlanId are used as textual conventions in this document.
These textual conventions have NO effect on either the syntax nor the
semantics of any managed object. Objects defined using these
conventions are always encoded by means of the rules that define their
primitive type. Hence, no changes to the SMI or the SNMP are necessary
to accommodate these textual conventions which are adopted merely for
the convenience of readers.
3.4. Relationship to Other MIBs
As described above, some IEEE 802.1D management objects have not been
included in this MIB because they overlap with objects in other MIBs
applicable to a bridge implementing this MIB. In particular, it is
assumed that a bridge implementing this MIB will also implement (at
least) the 'system' group defined in MIB-II [24], the 'interfaces' group
defined in [22] and the old Bridge MIB [21].
Bell, et al. Expires September 1999 [Page 13]
Internet Draft Bridge MIB Extensions March 1999
3.4.1. Relationship to the 'system' group
In MIB-II, the 'system' group is defined as being mandatory for all
systems such that each managed entity contains one instance of each
object in the 'system' group. Thus, those objects apply to the entity
as a whole irrespective of whether the entity's sole functionality is
bridging, or whether bridging is only a subset of the entity's
functionality.
3.4.2. Relation to Interfaces MIB
RFC 1573, the Interface MIB Evolution [22], requires that any MIB which
is an adjunct of the Interface MIB, clarify specific areas within the
Interface MIB. These areas were intentionally left vague in [22] to
avoid over constraining the MIB, thereby precluding management of
certain media-types.
Section 3.3 of [22] enumerates several areas which a media-specific MIB
must clarify. Each of these areas is addressed in a following
subsection. The implementor is referred to [22] in order to understand
the general intent of these areas.
In [22], the 'interfaces' group is defined as being mandatory for all
systems and contains information on an entity's interfaces, where each
interface is thought of as being attached to a `subnetwork'. (Note that
this term is not to be confused with `subnet' which refers to an
addressing partitioning scheme used in the Internet suite of protocols.)
The term 'segment' is used in this memo to refer to such a subnetwork,
whether it be an Ethernet segment, a 'ring', a WAN link, or even an X.25
virtual circuit.
Implicit in this Bridge MIB is the notion of ports on a bridge. Each of
these ports is associated with one interface of the 'interfaces' group
(one row in ifTable) and, in most situations, each port is associated
with a different interface. However, there are situations in which
multiple ports are associated with the same interface. An example of
such a situation would be several ports each corresponding one-to-one
with several X.25 virtual circuits but all on the same interface.
Each port is uniquely identified by a port number. A port number has no
mandatory relationship to an interface number, but in the simple case a
port number will have the same value as the corresponding interface's
interface number. Port numbers are in the range (1..dot1dBaseNumPorts).
Bell, et al. Expires September 1999 [Page 14]
Internet Draft Bridge MIB Extensions March 1999
Some entities perform other functionality as well as bridging through
the sending and receiving of data on their interfaces. In such
situations, only a subset of the data sent/received on an interface is
within the domain of the entity's bridging functionality. This subset
is considered to be delineated according to a set of protocols, with
some protocols being bridged, and other protocols not being bridged.
For example, in an entity which exclusively performed bridging, all
protocols would be considered as being bridged, whereas in an entity
which performed IP routing on IP datagrams and only bridged other
protocols, only the non-IP data would be considered as being bridged.
Thus, this Bridge MIB (and in particular, its counters) is applicable
only to that subset of the data on an entity's interfaces which is
sent/received for a protocol being bridged. All such data is
sent/received via the ports of the bridge.
3.4.2.1. Layering Model
This memo assumes the interpretation of the Interfaces Group to be in
accordance with [22] which states that the interfaces table (ifTable)
contains information on the managed resource's interfaces and that each
sub-layer below the internetwork layer of a network interface is
considered an interface.
This memo recommends that, within an entity, VLANs which are
instantiated as an entry in dot1qVlanCurrentTable by either management
configuration through dot1qVlanStaticTable or by dynamic means (e.g.
through GVRP), are NOT also represented by an entry in ifTable.
Where an entity contains higher-layer protocol entities e.g. IP-layer
interfaces, that transmit and receive traffic to/from a VLAN, these
should be represented in the ifTable as interfaces of type
propVirtual(53).
3.4.2.2. ifStackTable
In addition, [22] defines a table 'ifStackTable' for describing the
relationship between logical interfaces within an entity. It is
anticipated that implementors will use this table to describe the
binding of e.g. IP interfaces to physical ports, although the presence
of VLANs makes the representation less than perfect for showing
connectivity: the ifStackTable cannot represent the full capability of
the 802.1Q VLAN bridging standard since that makes a distinction between
VLAN bindings on 'ingress' to and 'egress' from a port: these
Bell, et al. Expires September 1999 [Page 15]
Internet Draft Bridge MIB Extensions March 1999
relationships may or may not be symmetrical whereas [22] assumes a
symmetrical binding for transmit and receive. This makes it necessary
to define other manageable objects for configuring which ports are
members of which VLANs.
3.4.2.3. ifRcvAddressTable
This table contains all MAC addresses, unicast, multicast, and
broadcast, for which an interface will receive packets and forward them
up to a higher layer entity for local consumption. Note that this does
not include addresses for data-link layer control protocols such as
Spanning-Tree, GMRP or GVRP. The format of the address, contained in
ifRcvAddressAddress, is the same as for ifPhysAddress.
This table does not include unicast or multicast addresses which are
accepted for possible forwarding out some other port. This table is
explicitly not intended to provide a bridge address filtering mechanism.
3.4.3. Relation to Basic Bridge MIB
This section defines how objects in the basic bridge MIB module should
be represented for devices which implement the extensions: some of the
old objects are less useful in such devices but must still be
implemented for reasons of backwards comaptibility. Note that formal
conformance statements for that MIB module do not exist since it is
defined in SMIv1.
3.4.3.1. The dot1dBase Group
This mandatory group contains the objects which are applicable to all
types of bridges. Interpretation of this group is unchanged.
3.4.3.2. The dot1dStp Group
This group contains the objects that denote the bridge's state with
respect to the Spanning Tree Protocol. Interpretation of this group is
unchanged.
Bell, et al. Expires September 1999 [Page 16]
Internet Draft Bridge MIB Extensions March 1999
3.4.3.3. The dot1dTp Group
This group contains objects that describe the entity's state with
respect to transparent bridging.
In a device operating with a single Filtering Database, interpretation
of this group is unchanged.
In a device supporting multiple Filtering Databases, this group is
interpreted as follows:
dot1dTpLearnedEntryDiscards
The number of times that *any* of the FDBs became full.
dot1dTpAgingTime
This applies to all Filtering Databases.
dot1dTpFdbTable
Report MAC addresses learned on each port, regardless of which
Filtering Database they have been learnt in. If an address has
been learnt in multiple databases on a single port, report it only
once. If an address has been learnt in multiple databases on more
than one port, report the entry on any one of the valid ports.
dot1dTpPortTable
This table is port-based and is not affected by multiple Filtering
Databases or multiple VLANs. The counters should include frames
received or transmitted for all VLANs. Note that equivalent 64-bit
port statistics counters are defined in this document for high-
capacity network interfaces with conformance statements to indicate
for which speeds of interface they are required.
3.4.3.4. The dot1dStatic Group
This optional group contains objects that describe the configuration of
destination-address filtering.
In a device operating with a single Filtering Database, interpretation
of this group is unchanged.
In a device supporting multiple Filtering Databases, this group is
interpreted as follows:
Bell, et al. Expires September 1999 [Page 17]
Internet Draft Bridge MIB Extensions March 1999
dot1dStaticTable
Entries read from this table include all static entries from all of
the Filtering Databases. Entries for the same MAC address and
receive port in more than one Filtering Database must appear only
once since these are the indices of this table. This table should
be implemented as read-only in devices that support multiple
Forwarding Databases - instead, write access should be provided
through dot1qStaticUnicastTable and dot1qStaticMulticastTable, as
defined in this document.
4. Extensions to RFC 1493
In addition to the objects in RFC1493, this document contains:
(1) References point to sections of IEEE 802.1D-1998.
(2) Added support for multiple traffic classes and dynamic multicast
filtering as per IEEE 802.1D-1998.
(3) Added support for bridged Virtual LANs as per IEEE 802.1Q-1998.
(4) Added support for 64-bit versions of existing RFC1493 port
counters.
Bell, et al. Expires September 1999 [Page 18]
Internet Draft Bridge MIB Extensions March 1999
5. Definitions for Extended Bridge MIB
P-BRIDGE-MIB DEFINITIONS ::= BEGIN
-- -------------------------------------------------------------
-- IEEE 802.1p MIB
-- -------------------------------------------------------------
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64
FROM SNMPv2-SMI
TruthValue, TimeInterval, MacAddress, TEXTUAL-CONVENTION
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
dot1dTp, dot1dTpPort, dot1dBridge,
dot1dBasePortEntry, dot1dBasePort
FROM BRIDGE-MIB;
pBridgeMIB MODULE-IDENTITY
LAST-UPDATED "9903020000Z"
ORGANIZATION "IETF Bridge MIB Working Group"
CONTACT-INFO
" Les Bell
Postal: 3Com Europe Ltd.
3Com Centre, Boundary Way
Hemel Hempstead, Herts. HP2 7YU
UK
Phone: +44 (1442) 438025
Email: Les_Bell@3Com.com
Andrew Smith
Postal: Extreme Networks
10460 Bandley Drive
Cupertino CA 95014
USA
Phone: +1 (408) 342 0999
Email: andrew@extremenetworks.com
Paul Langille
Postal: Newbridge Networks
5 Corporate Drive
Andover, MA 01810
USA
Bell, et al. Expires September 1999 [Page 19]
Internet Draft Bridge MIB Extensions March 1999
Phone: +1 (978) 691 4665
Email: langille@newbridge.com
Anil Rijhsinghani
Postal: Cabletron Systems
50 Minuteman Road
Andover MA 01810
USA
Phone: +1 (978) 684 1295
Email: anil@cabletron.com
Keith McCloghrie
Postal: cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Phone: +1 (408) 526 5260
Email: kzm@cisco.com"
DESCRIPTION
"The Bridge MIB Extension module for managing Priority
and Multicast Filtering, defined by IEEE 802.1D-1998."
::= { dot1dBridge 6 }
pBridgeMIBObjects OBJECT IDENTIFIER ::= { pBridgeMIB 1 }
-- -------------------------------------------------------------
-- Textual Conventions
-- -------------------------------------------------------------
EnabledStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A simple status value for the object."
SYNTAX INTEGER { enabled(1), disabled(2) }
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- groups in the P-BRIDGE MIB
-- -------------------------------------------------------------
dot1dExtBase OBJECT IDENTIFIER ::= { pBridgeMIBObjects 1 }
dot1dPriority OBJECT IDENTIFIER ::= { pBridgeMIBObjects 2 }
dot1dGarp OBJECT IDENTIFIER ::= { pBridgeMIBObjects 3 }
Bell, et al. Expires September 1999 [Page 20]
Internet Draft Bridge MIB Extensions March 1999
dot1dGmrp OBJECT IDENTIFIER ::= { pBridgeMIBObjects 4 }
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- the dot1dExtBase group
-- -------------------------------------------------------------
dot1dDeviceCapabilities OBJECT-TYPE
SYNTAX BITS {
dot1dExtendedFilteringServices(0),
-- can perform filtering of
-- individual multicast addresses
-- controlled by GMRP.
dot1dTrafficClasses(1),
-- can map user priority to
-- multiple traffic classes.
dot1qStaticEntryIndividualPort(2),
-- dot1qStaticUnicastReceivePort &
-- dot1qStaticMulticastReceivePort
-- can represent non-zero entries.
dot1qIVLCapable(3), -- Independent VLAN Learning.
dot1qSVLCapable(4), -- Shared VLAN Learning.
dot1qHybridCapable(5),
-- both IVL & SVL simultaneously.
dot1qConfigurablePvidTagging(6),
-- whether the implementation
-- supports the ability to
-- override the default PVID
-- setting and its egress status
-- (VLAN-Tagged or Untagged) on
-- each port.
dot1dLocalVlanCapable(7)
-- can support multiple local
-- bridges, outside of the scope
-- of 802.1Q defined VLANs.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the optional parts of IEEE 802.1D and 802.1Q
that are implemented by this device and are managable
through this MIB. Capabilities that are allowed on a
per-port basis are indicated in dot1dPortCapabilities."
REFERENCE
Bell, et al. Expires September 1999 [Page 21]
Internet Draft Bridge MIB Extensions March 1999
"ISO/IEC 15802-3 Section 5.2,
IEEE 802.1Q/D11 Section 5.2, 12.10.1.1.3/b/2"
::= { dot1dExtBase 1 }
dot1dTrafficClassesEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value true(1) indicates that Traffic Classes are
enabled on this bridge. When false(2), the bridge
operates with a single priority level for all traffic."
DEFVAL { true }
::= { dot1dExtBase 2 }
dot1dGmrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status requested by management for
GMRP. The value enabled(1) indicates that GMRP should
be enabled on this device, in all VLANs, on all ports
for which it has not been specifically disabled. When
disabled(2), GMRP is disabled, in all VLANs, on all
ports and all GMRP packets will be forwarded
transparently. This object affects both Applicant and
Registrar state machines. A transition from disabled(2)
to enabled(1) will cause a reset of all GMRP state
machines on all ports."
DEFVAL { enabled }
::= { dot1dExtBase 3 }
-- -------------------------------------------------------------
-- Port Capabilities Table
-- -------------------------------------------------------------
dot1dPortCapabilitiesTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dPortCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains capabilities information about
every port that is associated with this bridge."
::= { dot1dExtBase 4 }
Bell, et al. Expires September 1999 [Page 22]
Internet Draft Bridge MIB Extensions March 1999
dot1dPortCapabilitiesEntry OBJECT-TYPE
SYNTAX Dot1dPortCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of capabilities information about this port
indexed by dot1dBasePort."
AUGMENTS { dot1dBasePortEntry }
::= { dot1dPortCapabilitiesTable 1 }
Dot1dPortCapabilitiesEntry ::=
SEQUENCE {
dot1dPortCapabilities
BITS
}
dot1dPortCapabilities OBJECT-TYPE
SYNTAX BITS {
dot1qDot1qTagging(0), -- supports 802.1Q VLAN tagging of
-- frames and GVRP.
dot1qConfigurableAcceptableFrameTypes(1),
-- allows modified values of
-- dot1qPortAcceptableFrameTypes.
dot1qIngressFiltering(2)
-- supports the discarding of any
-- frame received on a Port whose
-- VLAN classification does not
-- include that Port in its Member
-- set.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the parts of IEEE 802.1D and 802.1Q that are
optional on a per-port basis that are implemented by
this device and are managable through this MIB."
REFERENCE
"ISO/IEC 15802-3 Section 5.2,
IEEE 802.1Q/D11 Section 5.2"
::= { dot1dPortCapabilitiesEntry 1 }
-- -------------------------------------------------------------
-- the dot1dPriority group
-- -------------------------------------------------------------
Bell, et al. Expires September 1999 [Page 23]
Internet Draft Bridge MIB Extensions March 1999
-- -------------------------------------------------------------
-- Port Priority Table
-- -------------------------------------------------------------
dot1dPortPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dPortPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about every port that
is associated with this transparent bridge."
::= { dot1dPriority 1 }
dot1dPortPriorityEntry OBJECT-TYPE
SYNTAX Dot1dPortPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Default User Priorities for each port of a
transparent bridge. This is indexed by dot1dBasePort."
AUGMENTS { dot1dBasePortEntry }
::= { dot1dPortPriorityTable 1 }
Dot1dPortPriorityEntry ::=
SEQUENCE {
dot1dPortDefaultUserPriority
INTEGER,
dot1dPortNumTrafficClasses
INTEGER
}
dot1dPortDefaultUserPriority OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default ingress User Priority for this port. This
only has effect on media, such as Ethernet, that do not
support native User Priority."
::= { dot1dPortPriorityEntry 1 }
dot1dPortNumTrafficClasses OBJECT-TYPE
SYNTAX INTEGER (1..8)
MAX-ACCESS read-write
STATUS current
Bell, et al. Expires September 1999 [Page 24]
Internet Draft Bridge MIB Extensions March 1999
DESCRIPTION
"The number of egress traffic classes supported on this
port. This object may optionally be read-only."
::= { dot1dPortPriorityEntry 2 }
-- -------------------------------------------------------------
-- User Priority Regeneration Table
-- -------------------------------------------------------------
dot1dUserPriorityRegenTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dUserPriorityRegenEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Regenerated User Priorities for each received
User Priority on each port of a bridge. The Regenerated
User Priority value may be used to index the Traffic
Class Table for each input port. This only has effect
on media that support native User Priority. The default
values for Regenerated User Priorities are the same as
the User Priorities."
REFERENCE
"ISO/IEC 15802-3 Section 6.4"
::= { dot1dPriority 2 }
dot1dUserPriorityRegenEntry OBJECT-TYPE
SYNTAX Dot1dUserPriorityRegenEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A mapping of incoming User Priority to a Regenerated
User Priority."
INDEX { dot1dBasePort, dot1dUserPriority }
::= { dot1dUserPriorityRegenTable 1 }
Dot1dUserPriorityRegenEntry ::=
SEQUENCE {
dot1dUserPriority
INTEGER,
dot1dRegenUserPriority
INTEGER
}
dot1dUserPriority OBJECT-TYPE
SYNTAX INTEGER (0..7)
Bell, et al. Expires September 1999 [Page 25]
Internet Draft Bridge MIB Extensions March 1999
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The User Priority for a frame received on this port."
::= { dot1dUserPriorityRegenEntry 1 }
dot1dRegenUserPriority OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Regenerated User Priority the incoming User
Priority is mapped to for this port."
::= { dot1dUserPriorityRegenEntry 2 }
-- -------------------------------------------------------------
-- Traffic Class Table
-- -------------------------------------------------------------
dot1dTrafficClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dTrafficClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table mapping evaluated User Priority to Traffic
Class, for forwarding by the bridge. Traffic class is a
number in the range (0..(dot1dPortNumTrafficClasses-1))."
REFERENCE
"ISO/IEC 15802-3 Table 7-2"
::= { dot1dPriority 3 }
dot1dTrafficClassEntry OBJECT-TYPE
SYNTAX Dot1dTrafficClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"User Priority to Traffic Class mapping."
INDEX { dot1dBasePort, dot1dTrafficClassPriority }
::= { dot1dTrafficClassTable 1 }
Dot1dTrafficClassEntry ::=
SEQUENCE {
dot1dTrafficClassPriority
INTEGER,
dot1dTrafficClass
Bell, et al. Expires September 1999 [Page 26]
Internet Draft Bridge MIB Extensions March 1999
INTEGER
}
dot1dTrafficClassPriority OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Priority value determined for the received frame.
This value is equivalent to the priority indicated in
the tagged frame received, or one of the evaluated
priorities, determined according to the media-type.
For untagged frames received from Ethernet media, this
value is equal to the dot1dPortDefaultUserPriority value
for the ingress port.
For untagged frames received from non-Ethernet media,
this value is equal to the dot1dRegenUserPriority value
for the ingress port and media-specific user priority."
::= { dot1dTrafficClassEntry 1 }
dot1dTrafficClass OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Traffic Class the received frame is mapped to."
::= { dot1dTrafficClassEntry 2 }
-- -------------------------------------------------------------
-- Outbound Access Priority Table
-- -------------------------------------------------------------
dot1dPortOutboundAccessPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dPortOutboundAccessPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table mapping Regenerated User Priority to Outbound
Access Priority. This is a fixed mapping for all port
types, with two options for 802.5 Token Ring."
REFERENCE
"ISO/IEC 15802-3 Table 7-3"
::= { dot1dPriority 4 }
Bell, et al. Expires September 1999 [Page 27]
Internet Draft Bridge MIB Extensions March 1999
dot1dPortOutboundAccessPriorityEntry OBJECT-TYPE
SYNTAX Dot1dPortOutboundAccessPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Regenerated User Priority to Outbound Access Priority
mapping."
INDEX { dot1dBasePort, dot1dRegenUserPriority }
::= { dot1dPortOutboundAccessPriorityTable 1 }
Dot1dPortOutboundAccessPriorityEntry ::=
SEQUENCE {
dot1dPortOutboundAccessPriority
INTEGER
}
dot1dPortOutboundAccessPriority OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Outbound Access Priority the received frame is
mapped to."
::= { dot1dPortOutboundAccessPriorityEntry 1 }
-- -------------------------------------------------------------
-- the dot1dGarp group
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- The GARP Port Table
-- -------------------------------------------------------------
dot1dPortGarpTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dPortGarpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of GARP control information about every bridge
port. This is indexed by dot1dBasePort."
::= { dot1dGarp 1 }
dot1dPortGarpEntry OBJECT-TYPE
SYNTAX Dot1dPortGarpEntry
MAX-ACCESS not-accessible
Bell, et al. Expires September 1999 [Page 28]
Internet Draft Bridge MIB Extensions March 1999
STATUS current
DESCRIPTION
"GARP control information for a bridge port."
AUGMENTS { dot1dBasePortEntry }
::= { dot1dPortGarpTable 1 }
Dot1dPortGarpEntry ::=
SEQUENCE {
dot1dPortGarpJoinTime
TimeInterval,
dot1dPortGarpLeaveTime
TimeInterval,
dot1dPortGarpLeaveAllTime
TimeInterval
}
dot1dPortGarpJoinTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The GARP Join time, in centiseconds."
DEFVAL { 20 }
::= { dot1dPortGarpEntry 1 }
dot1dPortGarpLeaveTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The GARP Leave time, in centiseconds."
DEFVAL { 60 }
::= { dot1dPortGarpEntry 2 }
dot1dPortGarpLeaveAllTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The GARP LeaveAll time, in centiseconds."
DEFVAL { 1000 }
::= { dot1dPortGarpEntry 3 }
-- -------------------------------------------------------------
-- The GMRP Port Configuration and Status Table
Bell, et al. Expires September 1999 [Page 29]
Internet Draft Bridge MIB Extensions March 1999
-- -------------------------------------------------------------
dot1dPortGmrpTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dPortGmrpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of GMRP control and status information about
every bridge port. Augments the dot1dBasePortTable."
::= { dot1dGmrp 1 }
dot1dPortGmrpEntry OBJECT-TYPE
SYNTAX Dot1dPortGmrpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"GMRP control and status information for a bridge port."
AUGMENTS { dot1dBasePortEntry }
::= { dot1dPortGmrpTable 1 }
Dot1dPortGmrpEntry ::=
SEQUENCE {
dot1dPortGmrpStatus
EnabledStatus,
dot1dPortGmrpFailedRegistrations
Counter32,
dot1dPortGmrpLastPduOrigin
MacAddress
}
dot1dPortGmrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The state of GMRP operation on this port. The value
enabled(1) indicates that GMRP is enabled on this port,
in all VLANs, as long as dot1dGmrpStatus is also enabled
for this device. When disabled(2) but dot1dGmrpStatus
is still enabled for the device, GMRP is disabled on
this port in all VLANs: any GMRP packets received will
be silently discarded and no GMRP registrations will be
propagated from other ports. This object affects all
GMRP Applicant and Registrar state machines on this
port. A transition from disabled(2) to enabled(1) will
Bell, et al. Expires September 1999 [Page 30]
Internet Draft Bridge MIB Extensions March 1999
cause a reset of all GMRP state machines on this port."
DEFVAL { enabled }
::= { dot1dPortGmrpEntry 1 }
dot1dPortGmrpFailedRegistrations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of failed GMRP registrations, for any
reason, in all VLANs, on this port."
::= { dot1dPortGmrpEntry 2 }
dot1dPortGmrpLastPduOrigin OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Source MAC Address of the last GMRP message
received on this port."
::= { dot1dPortGmrpEntry 3 }
-- -------------------------------------------------------------
-- High Capacity Port Table for Transparent Bridges
-- -------------------------------------------------------------
dot1dTpHCPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dTpHCPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about every high
capacity port that is associated with this transparent
bridge."
::= { dot1dTp 5 }
dot1dTpHCPortEntry OBJECT-TYPE
SYNTAX Dot1dTpHCPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics information for each high capacity port of a
transparent bridge."
INDEX { dot1dTpPort }
::= { dot1dTpHCPortTable 1 }
Bell, et al. Expires September 1999 [Page 31]
Internet Draft Bridge MIB Extensions March 1999
Dot1dTpHCPortEntry ::=
SEQUENCE {
dot1dTpHCPortInFrames
Counter64,
dot1dTpHCPortOutFrames
Counter64,
dot1dTpHCPortInDiscards
Counter64
}
dot1dTpHCPortInFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames that have been received by this
port from its segment. Note that a frame received on
the interface corresponding to this port is only counted
by this object if and only if it is for a protocol being
processed by the local bridging function, including
bridge management frames."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpHCPortEntry 1 }
dot1dTpHCPortOutFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames that have been transmitted by this
port to its segment. Note that a frame transmitted on
the interface corresponding to this port is only counted
by this object if and only if it is for a protocol being
processed by the local bridging function, including
bridge management frames."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpHCPortEntry 2 }
dot1dTpHCPortInDiscards OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Bell, et al. Expires September 1999 [Page 32]
Internet Draft Bridge MIB Extensions March 1999
"Count of valid frames that have been received by this
port from its segment which were discarded (i.e.,
filtered) by the Forwarding Process."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpHCPortEntry 3 }
-- -------------------------------------------------------------
-- Overflow Port Table for High Capacity Transparent Bridges
-- -------------------------------------------------------------
dot1dTpPortOverflowTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1dTpPortOverflowEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about every high
capacity port that is associated with this transparent
bridge."
::= { dot1dTp 6 }
dot1dTpPortOverflowEntry OBJECT-TYPE
SYNTAX Dot1dTpPortOverflowEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics information for each high capacity port of a
transparent bridge."
INDEX { dot1dTpPort }
::= { dot1dTpPortOverflowTable 1 }
Dot1dTpPortOverflowEntry ::=
SEQUENCE {
dot1dTpPortInOverflowFrames
Counter32,
dot1dTpPortOutOverflowFrames
Counter32,
dot1dTpPortInOverflowDiscards
Counter32
}
dot1dTpPortInOverflowFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Bell, et al. Expires September 1999 [Page 33]
Internet Draft Bridge MIB Extensions March 1999
DESCRIPTION
"The number of times the associated dot1dTpPortInFrames
counter has overflowed."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpPortOverflowEntry 1 }
dot1dTpPortOutOverflowFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dot1dTpPortOutFrames
counter has overflowed."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpPortOverflowEntry 2 }
dot1dTpPortInOverflowDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated
dot1dTpPortInDiscards counter has overflowed."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1dTpPortOverflowEntry 3 }
-- -------------------------------------------------------------
-- IEEE 802.1p MIB - Conformance Information
-- -------------------------------------------------------------
pBridgeConformance OBJECT IDENTIFIER ::= { pBridgeMIB 2 }
pBridgeGroups OBJECT IDENTIFIER ::= { pBridgeConformance 1 }
pBridgeCompliances OBJECT IDENTIFIER
::= { pBridgeConformance 2 }
-- -------------------------------------------------------------
-- units of conformance
-- -------------------------------------------------------------
pBridgeExtCapGroup OBJECT-GROUP
Bell, et al. Expires September 1999 [Page 34]
Internet Draft Bridge MIB Extensions March 1999
OBJECTS {
dot1dDeviceCapabilities,
dot1dPortCapabilities
}
STATUS current
DESCRIPTION
"A collection of objects indicating the optional
capabilites of the device."
::= { pBridgeGroups 1 }
pBridgeDeviceGmrpGroup OBJECT-GROUP
OBJECTS {
dot1dGmrpStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing device-level control
for the Multicast Filtering extended bridge services."
::= { pBridgeGroups 2 }
pBridgeDevicePriorityGroup OBJECT-GROUP
OBJECTS {
dot1dTrafficClassesEnabled
}
STATUS current
DESCRIPTION
"A collection of objects providing device-level control
for the Priority services."
::= { pBridgeGroups 3 }
pBridgeDefaultPriorityGroup OBJECT-GROUP
OBJECTS {
dot1dPortDefaultUserPriority
}
STATUS current
DESCRIPTION
"A collection of objects defining the User Priority
applicable to each port for media which do not support
native User Priority."
::= { pBridgeGroups 4 }
pBridgeRegenPriorityGroup OBJECT-GROUP
OBJECTS {
dot1dRegenUserPriority
}
Bell, et al. Expires September 1999 [Page 35]
Internet Draft Bridge MIB Extensions March 1999
STATUS current
DESCRIPTION
"A collection of objects defining the User Priorities
applicable to each port for media which support native
User Priority."
::= { pBridgeGroups 5 }
pBridgePriorityGroup OBJECT-GROUP
OBJECTS {
dot1dPortNumTrafficClasses,
dot1dTrafficClass
}
STATUS current
DESCRIPTION
"A collection of objects defining the traffic classes
within a bridge for each evaluated User Priority."
::= { pBridgeGroups 6 }
pBridgeAccessPriorityGroup OBJECT-GROUP
OBJECTS {
dot1dPortOutboundAccessPriority
}
STATUS current
DESCRIPTION
"A collection of objects defining the media dependent
outbound access level for each priority."
::= { pBridgeGroups 7 }
pBridgePortGarpGroup OBJECT-GROUP
OBJECTS {
dot1dPortGarpJoinTime,
dot1dPortGarpLeaveTime,
dot1dPortGarpLeaveAllTime
}
STATUS current
DESCRIPTION
"A collection of objects providing port level control
and status information for GARP operation."
::= { pBridgeGroups 8 }
pBridgePortGmrpGroup OBJECT-GROUP
OBJECTS {
dot1dPortGmrpStatus,
dot1dPortGmrpFailedRegistrations,
dot1dPortGmrpLastPduOrigin
Bell, et al. Expires September 1999 [Page 36]
Internet Draft Bridge MIB Extensions March 1999
}
STATUS current
DESCRIPTION
"A collection of objects providing port level control
and status information for GMRP operation."
::= { pBridgeGroups 9 }
pBridgeHCPortGroup OBJECT-GROUP
OBJECTS {
dot1dTpHCPortInFrames,
dot1dTpHCPortOutFrames,
dot1dTpHCPortInDiscards
}
STATUS current
DESCRIPTION
"A collection of objects providing 64-bit statistics
counters for high capacity bridge ports."
::= { pBridgeGroups 10 }
pBridgePortOverflowGroup OBJECT-GROUP
OBJECTS {
dot1dTpPortInOverflowFrames,
dot1dTpPortOutOverflowFrames,
dot1dTpPortInOverflowDiscards
}
STATUS current
DESCRIPTION
"A collection of objects providing overflow statistics
counters for high capacity bridge ports."
::= { pBridgeGroups 11 }
-- -------------------------------------------------------------
-- compliance statements
-- -------------------------------------------------------------
pBridgeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for device support of Priority
and Multicast Filtering extended bridging services."
MODULE
MANDATORY-GROUPS { pBridgeExtCapGroup }
GROUP pBridgeDeviceGmrpGroup
Bell, et al. Expires September 1999 [Page 37]
Internet Draft Bridge MIB Extensions March 1999
DESCRIPTION
"This group is mandatory for devices supporting the
GMRP application, defined by the extended filtering
services."
GROUP pBridgeDevicePriorityGroup
DESCRIPTION
"This group is mandatory only for devices supporting
the priority forwarding operations defined by the
extended bridge services."
GROUP pBridgeDefaultPriorityGroup
DESCRIPTION
"This group is mandatory only for devices supporting
the priority forwarding operations defined by the
extended bridge services with media types, such as
Ethernet, that do not support native User Priority."
GROUP pBridgeRegenPriorityGroup
DESCRIPTION
"This group is mandatory only for devices supporting
the priority forwarding operations defined by the
extended bridge services with media types that also
support native User Priority."
GROUP pBridgePriorityGroup
DESCRIPTION
"This group is mandatory only for devices supporting
the priority forwarding operations defined by the
extended bridge services."
GROUP pBridgeAccessPriorityGroup
DESCRIPTION
"This group is optional."
GROUP pBridgePortGarpGroup
DESCRIPTION
"This group is mandatory for devices supporting any
of the GARP applications: e.g. GMRP, defined by the
extended filtering services of 802.1D; or GVRP,
defined by 802.1Q (refer to the Q-BRIDGE-MIB for
conformance statements for GVRP)."
GROUP pBridgePortGmrpGroup
DESCRIPTION
Bell, et al. Expires September 1999 [Page 38]
Internet Draft Bridge MIB Extensions March 1999
"This group is mandatory for devices supporting the
GMRP application, defined by the extended filtering
services."
GROUP pBridgeHCPortGroup
DESCRIPTION
"This group is mandatory if the network interface
to which this bridge port is attached has the
value of the corresponding instance of ifSpeed
greater than 650,000,000 bits/second."
GROUP pBridgePortOverflowGroup
DESCRIPTION
"This group is optional."
OBJECT dot1dPortNumTrafficClasses
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dot1dTrafficClass
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dot1dRegenUserPriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { pBridgeCompliances 1 }
END
Bell, et al. Expires September 1999 [Page 39]
Internet Draft Bridge MIB Extensions March 1999
6. Definitions for Virtual Bridge MIB
Q-BRIDGE-MIB DEFINITIONS ::= BEGIN
-- -------------------------------------------------------------
-- IEEE 802.1Q MIB
-- -------------------------------------------------------------
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Counter32, Counter64, Unsigned32, TimeTicks
FROM SNMPv2-SMI
RowStatus, TruthValue, DisplayString, TEXTUAL-CONVENTION,
MacAddress
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
dot1dBridge, dot1dBasePortEntry, dot1dBasePort
FROM BRIDGE-MIB
EnabledStatus
FROM P-BRIDGE-MIB
TimeFilter
FROM RMON2-MIB;
qBridgeMIB MODULE-IDENTITY
LAST-UPDATED "9903020000Z"
ORGANIZATION "IETF Bridge MIB Working Group"
CONTACT-INFO
" Les Bell
Postal: 3Com Europe Ltd.
3Com Centre, Boundary Way
Hemel Hempstead, Herts. HP2 7YU
UK
Phone: +44 (1442) 438025
Email: Les_Bell@3Com.com
Andrew Smith
Postal: Extreme Networks
10460 Bandley Drive
Cupertino CA 95014
USA
Phone: +1 (408) 342 0999
Email: andrew@extremenetworks.com
Bell, et al. Expires September 1999 [Page 40]
Internet Draft Bridge MIB Extensions March 1999
Paul Langille
Postal: Newbridge Networks
5 Corporate Drive
Andover, MA 01810
USA
Phone: +1 (978) 691 4665
Email: langille@newbridge.com
Anil Rijhsinghani
Postal: Cabletron Systems
50 Minuteman Road
Andover MA 01810
USA
Phone: +1 (978) 684 1295
Email: anil@cabletron.com
Keith McCloghrie
Postal: cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Phone: +1 (408) 526 5260
Email: kzm@cisco.com"
DESCRIPTION
"The VLAN Bridge MIB module for managing Virtual Bridged
Local Area Networks, as defined by IEEE 802.1Q-1998."
::= { dot1dBridge 7 }
qBridgeMIBObjects OBJECT IDENTIFIER ::= { qBridgeMIB 1 }
-- -------------------------------------------------------------
-- Textual Conventions
-- -------------------------------------------------------------
PortList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through
8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
Bell, et al. Expires September 1999 [Page 41]
Internet Draft Bridge MIB Extensions March 1999
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'."
SYNTAX OCTET STRING
VlanIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A value used to index per-VLAN tables: values of 0 and
4095 are not permitted; if the value is between 1 and
4094 inclusive, it represents an 802.1Q VLAN-ID with
global scope within a given bridged domain (see VlanId
textual convention). If the value is greater than 4095
then it represents a VLAN with scope local to the
particular agent."
SYNTAX Unsigned32
VlanId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The 12-bit VLAN ID used in the VLAN Tag header."
SYNTAX INTEGER (1..4094)
-- -------------------------------------------------------------
-- groups in the Q-BRIDGE MIB
-- -------------------------------------------------------------
dot1qBase OBJECT IDENTIFIER ::= { qBridgeMIBObjects 1 }
dot1qTp OBJECT IDENTIFIER ::= { qBridgeMIBObjects 2 }
dot1qStatic OBJECT IDENTIFIER ::= { qBridgeMIBObjects 3 }
dot1qVlan OBJECT IDENTIFIER ::= { qBridgeMIBObjects 4 }
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- dot1qBase group
-- -------------------------------------------------------------
dot1qVlanVersionNumber OBJECT-TYPE
SYNTAX INTEGER {
version1(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of IEEE 802.1Q that this device
Bell, et al. Expires September 1999 [Page 42]
Internet Draft Bridge MIB Extensions March 1999
supports."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
::= { dot1qBase 1 }
dot1qMaxVlanId OBJECT-TYPE
SYNTAX VlanId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum IEEE 802.1Q VLAN ID that this device
supports."
REFERENCE
"IEEE 802.1Q/D11 Section 9.3.2.3"
::= { dot1qBase 2 }
dot1qMaxSupportedVlans OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of IEEE 802.1Q VLANs that this
device supports."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
::= { dot1qBase 3 }
dot1qNumVlans OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of IEEE 802.1Q VLANs that are
configured in this device."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.1.1"
::= { dot1qBase 4 }
dot1qGvrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status requested by management for
GVRP. The value enabled(1) indicates that GVRP should
Bell, et al. Expires September 1999 [Page 43]
Internet Draft Bridge MIB Extensions March 1999
be enabled on this device, on all ports for which it has
not been specifically disabled. When disabled(2), GVRP
is disabled on all ports and all GVRP packets will be
forwarded transparently. This object affects all GVRP
Applicant and Registrar state machines. A transition
from disabled(2) to enabled(1) will cause a reset of all
GVRP state machines on all ports."
DEFVAL { enabled }
::= { dot1qBase 5 }
-- -------------------------------------------------------------
-- the dot1qTp group
-- -------------------------------------------------------------
-- -------------------------------------------------------------
-- the current Filtering Database Table
-- -------------------------------------------------------------
dot1qFdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains configuration and control
information for each Filtering Database currently
operating on this device. Entries in this table appear
automatically when VLANs are assigned FDB IDs in the
dot1qVlanCurrentTable."
::= { dot1qTp 1 }
dot1qFdbEntry OBJECT-TYPE
SYNTAX Dot1qFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a specific Filtering Database."
INDEX { dot1qFdbId }
::= { dot1qFdbTable 1 }
Dot1qFdbEntry ::=
SEQUENCE {
dot1qFdbId
Unsigned32,
dot1qFdbDynamicCount
Counter32
Bell, et al. Expires September 1999 [Page 44]
Internet Draft Bridge MIB Extensions March 1999
}
dot1qFdbId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identity of this Filtering Database."
::= { dot1qFdbEntry 1 }
dot1qFdbDynamicCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of dynamic entries in this
Filtering Database."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.1.1.3"
::= { dot1qFdbEntry 2 }
-- -------------------------------------------------------------
-- Multiple Forwarding Databases for 802.1Q Transparent devices
-- This table is an alternative to the dot1dTpFdbTable,
-- previously defined for 802.1D devices which only support a
-- single Forwarding Database.
-- -------------------------------------------------------------
dot1qTpFdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qTpFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about unicast entries
for which the device has forwarding and/or filtering
information. This information is used by the
transparent bridging function in determining how to
propagate a received frame."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7"
::= { dot1qTp 2 }
dot1qTpFdbEntry OBJECT-TYPE
SYNTAX Dot1qTpFdbEntry
MAX-ACCESS not-accessible
Bell, et al. Expires September 1999 [Page 45]
Internet Draft Bridge MIB Extensions March 1999
STATUS current
DESCRIPTION
"Information about a specific unicast MAC address for
which the device has some forwarding and/or filtering
information."
INDEX { dot1qFdbId, dot1qTpFdbAddress }
::= { dot1qTpFdbTable 1 }
Dot1qTpFdbEntry ::=
SEQUENCE {
dot1qTpFdbAddress
MacAddress,
dot1qTpFdbPort
INTEGER,
dot1qTpFdbStatus
INTEGER
}
dot1qTpFdbAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unicast MAC address for which the device has
forwarding and/or filtering information."
::= { dot1qTpFdbEntry 1 }
dot1qTpFdbPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Either the value '0', or the port number of the port on
which a frame having a source address equal to the value
of the corresponding instance of dot1qTpFdbAddress has
been seen. A value of '0' indicates that the port
number has not been learned but that the device does
have some forwarding/filtering information about this
address (e.g. in the dot1qStaticUnicastTable).
Implementors are encouraged to assign the port value to
this object whenever it is learned even for addresses
for which the corresponding value of dot1qTpFdbStatus is
not learned(3)."
::= { dot1qTpFdbEntry 2 }
Bell, et al. Expires September 1999 [Page 46]
Internet Draft Bridge MIB Extensions March 1999
dot1qTpFdbStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
learned(3),
self(4),
mgmt(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of this entry. The meanings of the values
are:
other(1) - none of the following. This may include
the case where some other MIB object (not the
corresponding instance of dot1qTpFdbPort, nor an
entry in the dot1qStaticUnicastTable) is being
used to determine if and how frames addressed to
the value of the corresponding instance of
dot1qTpFdbAddress are being forwarded.
invalid(2) - this entry is no longer valid (e.g., it
was learned but has since aged out), but has not
yet been flushed from the table.
learned(3) - the value of the corresponding instance
of dot1qTpFdbPort was learned and is being used.
self(4) - the value of the corresponding instance of
dot1qTpFdbAddress represents one of the device's
addresses. The corresponding instance of
dot1qTpFdbPort indicates which of the device's
ports has this address.
mgmt(5) - the value of the corresponding instance of
dot1qTpFdbAddress is also the value of an
existing instance of dot1qStaticAddress."
::= { dot1qTpFdbEntry 3 }
-- -------------------------------------------------------------
-- Dynamic Group Registration Table
-- -------------------------------------------------------------
dot1qTpGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qTpGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for VLANs
Bell, et al. Expires September 1999 [Page 47]
Internet Draft Bridge MIB Extensions March 1999
configured into the bridge by (local or network)
management, or learnt dynamically, specifying the set of
ports to which frames received on a VLAN for this FDB
and containing a specific Group destination address are
allowed to be forwarded."
::= { dot1qTp 3 }
dot1qTpGroupEntry OBJECT-TYPE
SYNTAX Dot1qTpGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the bridge by
management, or learnt dynamically, specifying the set of
ports to which frames received on a VLAN and containing
a specific Group destination address, are allowed to be
forwarded. The subset of these ports learnt dynamically
is also provided."
INDEX { dot1qVlanIndex, dot1qTpGroupAddress }
::= { dot1qTpGroupTable 1 }
Dot1qTpGroupEntry ::=
SEQUENCE {
dot1qTpGroupAddress
MacAddress,
dot1qTpGroupEgressPorts
PortList,
dot1qTpGroupLearnt
PortList
}
dot1qTpGroupAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination Group MAC address in a frame to which
this entry's filtering information applies."
::= { dot1qTpGroupEntry 1 }
dot1qTpGroupEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Bell, et al. Expires September 1999 [Page 48]
Internet Draft Bridge MIB Extensions March 1999
"The complete set of ports, in this VLAN, to which
frames destined for this Group MAC address are currently
being explicitly forwarded. This does not include ports
for which this address is only implicitly forwarded, in
the dot1qForwardAllPorts list."
::= { dot1qTpGroupEntry 2 }
dot1qTpGroupLearnt OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The subset of ports in dot1qTpGroupEgressPorts which
were learnt by GMRP or some other dynamic mechanism, in
this Filtering database."
::= { dot1qTpGroupEntry 3 }
-- -------------------------------------------------------------
-- Service Requirements Group
-- -------------------------------------------------------------
dot1qForwardAllTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qForwardAllEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
all multicasts applies, configured statically by
management or dynamically by GMRP. An entry appears in
this table for all VLANs that are currently
instantiated."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.2, 12.7.7"
::= { dot1qTp 4 }
dot1qForwardAllEntry OBJECT-TYPE
SYNTAX Dot1qForwardAllEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Forwarding information for a VLAN, specifying the set
of ports to which all multicasts should be forwarded,
configured statically by management or dynamically by
GMRP."
Bell, et al. Expires September 1999 [Page 49]
Internet Draft Bridge MIB Extensions March 1999
INDEX { dot1qVlanIndex }
::= { dot1qForwardAllTable 1 }
Dot1qForwardAllEntry ::=
SEQUENCE {
dot1qForwardAllPorts
PortList,
dot1qForwardAllStaticPorts
PortList,
dot1qForwardAllForbiddenPorts
PortList
}
dot1qForwardAllPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The complete set of ports in this VLAN to which all
multicast group-addressed frames are to be forwarded.
This includes ports for which this need has been
determined dynamically by GMRP, or configured statically
by management."
::= { dot1qForwardAllEntry 1 }
dot1qForwardAllStaticPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management in this VLAN
to which all multicast group-addressed frames are to be
forwarded. Ports entered in this list will also appear
in the complete set shown by dot1qForwardAllPorts. This
value will be restored after the device is reset. This
only applies to ports that are members of the VLAN,
defined by dot1qVlanCurrentEgressPorts. A port may not
be added in this set if it is already a member of the
set of ports in dot1qForwardAllForbiddenPorts. The
default value is a string of ones of appropriate length,
to indicate standard non-EFS behaviour, i.e. forward
all multicasts to all ports."
::= { dot1qForwardAllEntry 2 }
dot1qForwardAllForbiddenPorts OBJECT-TYPE
Bell, et al. Expires September 1999 [Page 50]
Internet Draft Bridge MIB Extensions March 1999
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management in this VLAN
for which the Service Requirement attribute Forward All
Multicast Groups may not be dynamically registered by
GMRP. This value will be restored after the device is
reset. A port may not be added in this set if it is
already a member of the set of ports in
dot1qForwardAllStaticPorts. The default value is a
string of zeros of appropriate length."
::= { dot1qForwardAllEntry 3 }
dot1qForwardUnregisteredTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qForwardUnregisteredEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
multicast group-addressed frames for which there is no
more specific forwarding information applies. This is
configured statically by management and determined
dynamically by GMRP. An entry appears in this table for
all VLANs that are currently instantiated."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.2, 12.7.7"
::= { dot1qTp 5 }
dot1qForwardUnregisteredEntry OBJECT-TYPE
SYNTAX Dot1qForwardUnregisteredEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Forwarding information for a VLAN, specifying the set
of ports to which all multicasts for which there is no
more specific forwarding information shall be forwarded.
This is configured statically by management or
dynamically by GMRP."
INDEX { dot1qVlanIndex }
::= { dot1qForwardUnregisteredTable 1 }
Dot1qForwardUnregisteredEntry ::=
SEQUENCE {
Bell, et al. Expires September 1999 [Page 51]
Internet Draft Bridge MIB Extensions March 1999
dot1qForwardUnregisteredPorts
PortList,
dot1qForwardUnregisteredStaticPorts
PortList,
dot1qForwardUnregisteredForbiddenPorts
PortList
}
dot1qForwardUnregisteredPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The complete set of ports in this VLAN to which
multicast group-addressed frames for which there is no
more specific forwarding information will be forwarded.
This includes ports for which this need has been
determined dynamically by GMRP, or configured statically
by management."
::= { dot1qForwardUnregisteredEntry 1 }
dot1qForwardUnregisteredStaticPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports configured by management, in this
VLAN, to which multicast group-addressed frames for
which there is no more specific forwarding information
are to be forwarded. Ports entered in this list will
also appear in the complete set shown by
dot1qForwardUnregisteredPorts. This value will be
restored after the device is reset. A port may not be
added in this set if it is already a member of the set
of ports in dot1qForwardUnregisteredForbiddenPorts. The
default value is a string of zeros of appropriate
length, although this has no effect with the default
value of dot1qForwardAllStaticPorts."
::= { dot1qForwardUnregisteredEntry 2 }
dot1qForwardUnregisteredForbiddenPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Bell, et al. Expires September 1999 [Page 52]
Internet Draft Bridge MIB Extensions March 1999
"The set of ports configured by management in this VLAN
for which the Service Requirement attribute Forward
Unregistered Multicast Groups may not be dynamically
registered by GMRP. This value will be restored after
the device is reset. A port may not be added in this
set if it is already a member of the set of ports in
dot1qForwardUnregisteredStaticPorts. The default value
is a string of zeros of appropriate length."
::= { dot1qForwardUnregisteredEntry 3 }
-- -------------------------------------------------------------
-- The Static (Destination-Address Filtering) Database
-- -------------------------------------------------------------
dot1qStaticUnicastTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qStaticUnicastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for Unicast
MAC addresses for each Filtering Database, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific unicast
destination addresses are allowed to be forwarded. A
value of zero in this table as the port number from
which frames with a specific destination address are
received, is used to specify all ports for which there
is no specific entry in this table for that particular
destination address. Entries are valid for unicast
addresses only."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7,
ISO/IEC 15802-3 Section 7.9.1"
::= { dot1qStatic 1 }
dot1qStaticUnicastEntry OBJECT-TYPE
SYNTAX Dot1qStaticUnicastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from a specific port and
containing a specific unicast destination address are
Bell, et al. Expires September 1999 [Page 53]
Internet Draft Bridge MIB Extensions March 1999
allowed to be forwarded."
INDEX {
dot1qFdbId,
dot1qStaticUnicastAddress,
dot1qStaticUnicastReceivePort
}
::= { dot1qStaticUnicastTable 1 }
Dot1qStaticUnicastEntry ::=
SEQUENCE {
dot1qStaticUnicastAddress
MacAddress,
dot1qStaticUnicastReceivePort
INTEGER,
dot1qStaticUnicastAllowedToGoTo
PortList,
dot1qStaticUnicastStatus
INTEGER
}
dot1qStaticUnicastAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination MAC address in a frame to which this
entry's filtering information applies. This object must
take the value of a unicast address."
::= { dot1qStaticUnicastEntry 1 }
dot1qStaticUnicastReceivePort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Either the value '0', or the port number of the port
from which a frame must be received in order for this
entry's filtering information to apply. A value of zero
indicates that this entry applies on all ports of the
device for which there is no other applicable entry."
::= { dot1qStaticUnicastEntry 2 }
dot1qStaticUnicastAllowedToGoTo OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
Bell, et al. Expires September 1999 [Page 54]
Internet Draft Bridge MIB Extensions March 1999
STATUS current
DESCRIPTION
"The set of ports for which a frame with a specific
unicast address will be flooded in the event that it
has not been learned. It also specifies the set of
ports a specific unicast address may be dynamically
learnt on. The dot1qTpFdbTable will have an equivalent
entry with a dot1qTpFdbPort value of '0' until this
address has been learnt, when it will be updated with
the port the address has been seen on. This only
applies to ports that are members of the VLAN, defined
by dot1qVlanCurrentEgressPorts. The default value of
this object is a string of ones of appropriate length."
REFERENCE
"IEEE 802.1Q/D11 Table 8-5, ISO/IEC 15802-3 Table 7-5"
::= { dot1qStaticUnicastEntry 3 }
dot1qStaticUnicastStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
permanent(3),
deleteOnReset(4),
deleteOnTimeout(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use but
the conditions under which it will remain
so differ from the following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset of
the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently in
use and will remain so until it is aged out."
DEFVAL { permanent }
::= { dot1qStaticUnicastEntry 4 }
Bell, et al. Expires September 1999 [Page 55]
Internet Draft Bridge MIB Extensions March 1999
dot1qStaticMulticastTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qStaticMulticastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing filtering information for Multicast
and Broadcast MAC addresses for each VLAN, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific Multicast
and Broadcast destination addresses are allowed to be
forwarded. A value of zero in this table as the port
number from which frames with a specific destination
address are received, is used to specify all ports for
which there is no specific entry in this table for that
particular destination address. Entries are valid for
Multicast and Broadcast addresses only."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7,
ISO/IEC 15802-3 Section 7.9.1"
::= { dot1qStatic 2 }
dot1qStaticMulticastEntry OBJECT-TYPE
SYNTAX Dot1qStaticMulticastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from this specific port
for this VLAN and containing this Multicast or Broadcast
destination address are allowed to be forwarded."
INDEX {
dot1qVlanIndex,
dot1qStaticMulticastAddress,
dot1qStaticMulticastReceivePort
}
::= { dot1qStaticMulticastTable 1 }
Dot1qStaticMulticastEntry ::=
SEQUENCE {
dot1qStaticMulticastAddress
MacAddress,
dot1qStaticMulticastReceivePort
INTEGER,
Bell, et al. Expires September 1999 [Page 56]
Internet Draft Bridge MIB Extensions March 1999
dot1qStaticMulticastStaticEgressPorts
PortList,
dot1qStaticMulticastForbiddenEgressPorts
PortList,
dot1qStaticMulticastStatus
INTEGER
}
dot1qStaticMulticastAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination MAC address in a frame to which this
entry's filtering information applies. This object must
take the value of a Multicast or Broadcast address."
::= { dot1qStaticMulticastEntry 1 }
dot1qStaticMulticastReceivePort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Either the value '0', or the port number of the port
from which a frame must be received in order for this
entry's filtering information to apply. A value of zero
indicates that this entry applies on all ports of the
device for which there is no other applicable entry."
::= { dot1qStaticMulticastEntry 2 }
dot1qStaticMulticastStaticEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports to which frames received from a
specific port and destined for a specific Multicast or
Broadcast MAC address must be forwarded, regardless of
any dynamic information e.g. from GMRP. A port may not
be added in this set if it is already a member of the
set of ports in dot1qStaticMulticastForbiddenEgressPorts.
The default value of this object is a string of ones of
appropriate length."
::= { dot1qStaticMulticastEntry 3 }
Bell, et al. Expires September 1999 [Page 57]
Internet Draft Bridge MIB Extensions March 1999
dot1qStaticMulticastForbiddenEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The set of ports to which frames received from a
specific port and destined for a specific Multicast or
Broadcast MAC address must not be forwarded, regardless
of any dynamic information e.g. from GMRP. A port may
not be added in this set if it is already a member of the
set of ports in dot1qStaticMulticastStaticEgressPorts.
The default value of this object is a string of zeros of
appropriate length."
::= { dot1qStaticMulticastEntry 4 }
dot1qStaticMulticastStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
permanent(3),
deleteOnReset(4),
deleteOnTimeout(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use but
the conditions under which it will remain
so differ from the following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset of
the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently in
use and will remain so until it is aged out."
DEFVAL { permanent }
::= { dot1qStaticMulticastEntry 5 }
-- -------------------------------------------------------------
-- The Current VLAN Database
Bell, et al. Expires September 1999 [Page 58]
Internet Draft Bridge MIB Extensions March 1999
-- -------------------------------------------------------------
dot1qVlanNumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a VLAN entry has been deleted from
the dot1qVlanCurrentTable (for any reason). If an entry
is deleted, then inserted, and then deleted, this
counter will be incremented by 2."
::= { dot1qVlan 1 }
dot1qVlanCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qVlanCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing current configuration information
for each VLAN currently configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received."
::= { dot1qVlan 2 }
dot1qVlanCurrentEntry OBJECT-TYPE
SYNTAX Dot1qVlanCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information for a VLAN configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received."
INDEX { dot1qVlanTimeMark, dot1qVlanIndex }
::= { dot1qVlanCurrentTable 1 }
Dot1qVlanCurrentEntry ::=
SEQUENCE {
dot1qVlanTimeMark
TimeFilter,
dot1qVlanIndex
VlanIndex,
dot1qVlanFdbId
Unsigned32,
dot1qVlanCurrentEgressPorts
PortList,
Bell, et al. Expires September 1999 [Page 59]
Internet Draft Bridge MIB Extensions March 1999
dot1qVlanCurrentUntaggedPorts
PortList,
dot1qVlanStatus
INTEGER,
dot1qVlanCreationTime
TimeTicks
}
dot1qVlanTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A TimeFilter for this entry. See the TimeFilter
textual convention to see how this works."
::= { dot1qVlanCurrentEntry 1 }
dot1qVlanIndex OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VLAN-ID or other identifier refering to this VLAN."
::= { dot1qVlanCurrentEntry 2 }
dot1qVlanFdbId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Filtering Database used by this VLAN. This is one
of the dot1qFdbId values in the dot1qFdbTable. This
value is allocated automatically by the device whenever
the VLAN is created: either dynamically by GVRP, or by
management, in dot1qVlanStaticTable. Allocation of this
value follows the learning constraints defined for this
VLAN in dot1qLearningConstraintsTable."
::= { dot1qVlanCurrentEntry 3 }
dot1qVlanCurrentEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The set of ports which are transmitting traffic for
Bell, et al. Expires September 1999 [Page 60]
Internet Draft Bridge MIB Extensions March 1999
this VLAN as either tagged or untagged frames."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanCurrentEntry 4 }
dot1qVlanCurrentUntaggedPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The set of ports which are transmitting traffic for
this VLAN as untagged frames."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanCurrentEntry 5 }
dot1qVlanStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
permanent(2),
dynamicGvrp(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
other(1) - this entry is currently in use but the
conditions under which it will remain so differ
from the following values.
permanent(2) - this entry, corresponding to an entry
in dot1qVlanStaticTable, is currently in use and
will remain so after the next reset of the
device. The port lists for this entry include
ports from the equivalent dot1qVlanStaticTable
entry and ports learnt dynamically.
dynamicGvrp(3) - this entry is currently in use
and will remain so until removed by GVRP. There
is no static entry for this VLAN and it will be
removed when the last port leaves the VLAN."
::= { dot1qVlanCurrentEntry 6 }
dot1qVlanCreationTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
Bell, et al. Expires September 1999 [Page 61]
Internet Draft Bridge MIB Extensions March 1999
DESCRIPTION
"The value of sysUpTime when this VLAN was created."
::= { dot1qVlanCurrentEntry 7 }
-- -------------------------------------------------------------
-- The Static VLAN Database
-- -------------------------------------------------------------
dot1qVlanStaticTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qVlanStaticEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset."
::= { dot1qVlan 3 }
dot1qVlanStaticEntry OBJECT-TYPE
SYNTAX Dot1qVlanStaticEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Static information for a VLAN configured into the
device by (local or network) management."
INDEX { dot1qVlanIndex }
::= { dot1qVlanStaticTable 1 }
Dot1qVlanStaticEntry ::=
SEQUENCE {
dot1qVlanStaticName
DisplayString,
dot1qVlanStaticEgressPorts
PortList,
dot1qVlanForbiddenEgressPorts
PortList,
dot1qVlanStaticUntaggedPorts
PortList,
dot1qVlanStaticRowStatus
RowStatus
}
dot1qVlanStaticName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
Bell, et al. Expires September 1999 [Page 62]
Internet Draft Bridge MIB Extensions March 1999
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned string, which may be used
to identify the VLAN."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanStaticEntry 1 }
dot1qVlanStaticEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports which are permanently assigned to the
egress list for this VLAN by management. Changes to a
bit in this object affect the per-port per-VLAN
Registrar control for Registration Fixed for the
relevant GVRP state machine on each port. A port may
not be added in this set if it is already a member of
the set of ports in dot1qVlanForbiddenEgressPorts. The
default value of this object is a string of zeros of
appropriate length, indicating not fixed."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3"
::= { dot1qVlanStaticEntry 2 }
dot1qVlanForbiddenEgressPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports which are prohibited by management
from being included in the egress list for this VLAN.
Changes to this object that cause a port to be included
or excluded affect the per-port per-VLAN Registrar
control for Registration Forbidden for the relevant GVRP
state machine on each port. A port may not be added in
this set if it is already a member of the set of ports
in dot1qVlanStaticEgressPorts. The default value of
this object is a string of zeros of appropriate length,
excluding all ports from the forbidden set."
REFERENCE
"IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3"
::= { dot1qVlanStaticEntry 3 }
Bell, et al. Expires September 1999 [Page 63]
Internet Draft Bridge MIB Extensions March 1999
dot1qVlanStaticUntaggedPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of ports which should transmit egress packets
for this VLAN as untagged. The default value of this
object for the default VLAN (VlanId 001) is a string
of appropriate length including all ports. There is no
specified default for other VLANs. If a device cannot
support a value being set then its agent will reject the
set operation. Attempts to set more than one VLAN to be
untagged on egress may be rejected by devices which do
not support this option."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.2.1"
::= { dot1qVlanStaticEntry 4 }
dot1qVlanStaticRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the status of this entry."
::= { dot1qVlanStaticEntry 5 }
dot1qNextFreeLocalVlanIndex OBJECT-TYPE
SYNTAX INTEGER (0|4096..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The next available value for dot1qVlanIndex of a local
VLAN entry in dot1qVlanStaticTable. This will always
report values >=4096, if a new Local VLAN may be
created, or the value 0 if this is not possible. A row
creation operation in this table for an entry with a
local VlanIndex value may fail if this value is not used
as the index. This value will automatically change when
the current value is used."
::= { dot1qVlan 4 }
-- -------------------------------------------------------------
-- The VLAN Port Configuration Table
-- -------------------------------------------------------------
Bell, et al. Expires September 1999 [Page 64]
Internet Draft Bridge MIB Extensions March 1999
dot1qPortVlanTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing per port control and status
information for VLAN configuration in the device."
::= { dot1qVlan 5 }
dot1qPortVlanEntry OBJECT-TYPE
SYNTAX Dot1qPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information controlling VLAN configuration for a port
on the device. This is indexed by dot1dBasePort."
AUGMENTS { dot1dBasePortEntry }
::= { dot1qPortVlanTable 1 }
Dot1qPortVlanEntry ::=
SEQUENCE {
dot1qPvid
VlanIndex,
dot1qPortAcceptableFrameTypes
INTEGER,
dot1qPortIngressFiltering
TruthValue,
dot1qPortGvrpStatus
EnabledStatus,
dot1qPortGvrpFailedRegistrations
Counter32,
dot1qPortGvrpLastPduOrigin
MacAddress
}
dot1qPvid OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The PVID, the VLAN ID assigned to untagged frames or
Prority-Tagged frames received on this port."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.1"
DEFVAL { 1 }
Bell, et al. Expires September 1999 [Page 65]
Internet Draft Bridge MIB Extensions March 1999
::= { dot1qPortVlanEntry 1 }
dot1qPortAcceptableFrameTypes OBJECT-TYPE
SYNTAX INTEGER {
admitAll(1),
admitOnlyVlanTagged(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this is admitOnlyVlanTagged(2) the device will
discard untagged frames or Prority-Tagged frames
received on this port. When admitAll(1), untagged
frames or Prority-Tagged frames received on this port
will be accepted and assigned to the PVID for this port.
This control does not affect VLAN independent BPDU
frames, such as GVRP and STP. It does affect VLAN
dependent BPDU frames, such as GMRP."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.3"
DEFVAL { admitAll }
::= { dot1qPortVlanEntry 2 }
dot1qPortIngressFiltering OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this is true(1) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When false(2), the port will accept all
incoming frames.
This control does not affect VLAN independent BPDU
frames, such as GVRP and STP. It does affect VLAN
dependent BPDU frames, such as GMRP."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.1.4"
DEFVAL { false }
::= { dot1qPortVlanEntry 3 }
dot1qPortGvrpStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
Bell, et al. Expires September 1999 [Page 66]
Internet Draft Bridge MIB Extensions March 1999
STATUS current
DESCRIPTION
"The state of GVRP operation on this port. The value
enabled(1) indicates that GVRP is enabled on this port,
as long as dot1qGvrpStatus is also enabled for this
device. When disabled(2) but dot1qGvrpStatus is still
enabled for the device, GVRP is disabled on this port:
any GVRP packets received will be silently discarded and
no GVRP registrations will be propagated from other
ports. This object affects all GVRP Applicant and
Registrar state machines on this port. A transition
from disabled(2) to enabled(1) will cause a reset of all
GVRP state machines on this port."
DEFVAL { enabled }
::= { dot1qPortVlanEntry 4 }
dot1qPortGvrpFailedRegistrations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of failed GVRP registrations, for any
reason, on this port."
::= { dot1qPortVlanEntry 5 }
dot1qPortGvrpLastPduOrigin OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Source MAC Address of the last GVRP message
received on this port."
::= { dot1qPortVlanEntry 6 }
-- -------------------------------------------------------------
-- Per port VLAN Statistics Table
-- -------------------------------------------------------------
dot1qPortVlanStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qPortVlanStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing per port, per VLAN statistics for
traffic received."
Bell, et al. Expires September 1999 [Page 67]
Internet Draft Bridge MIB Extensions March 1999
::= { dot1qVlan 6 }
dot1qPortVlanStatisticsEntry OBJECT-TYPE
SYNTAX Dot1qPortVlanStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Traffic statistics for a VLAN on an interface."
INDEX { dot1dBasePort, dot1qVlanIndex }
::= { dot1qPortVlanStatisticsTable 1 }
Dot1qPortVlanStatisticsEntry ::=
SEQUENCE {
dot1qTpVlanPortInFrames
Counter32,
dot1qTpVlanPortOutFrames
Counter32,
dot1qTpVlanPortInDiscards
Counter32,
dot1qTpVlanPortInOverflowFrames
Counter32,
dot1qTpVlanPortOutOverflowFrames
Counter32,
dot1qTpVlanPortInOverflowDiscards
Counter32
}
dot1qTpVlanPortInFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames received by this port from
its segment which were classified as belonging to this
VLAN. Note that a frame received on this port is
counted by this object if and only if it is for a
protocol being processed by the local forwarding process
for this VLAN. This object includes received bridge
management frames classified as belonging to this VLAN
(e.g. GMRP, but not GVRP or STP)."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3(a)"
::= { dot1qPortVlanStatisticsEntry 1 }
dot1qTpVlanPortOutFrames OBJECT-TYPE
Bell, et al. Expires September 1999 [Page 68]
Internet Draft Bridge MIB Extensions March 1999
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames transmitted by this port to
its segment from the local forwarding process for this
VLAN. This includes bridge management frames originated
by this device whach are classified as belonging to this
VLAN (e.g. GMRP, but not GVRP or STP)."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3(d)"
::= { dot1qPortVlanStatisticsEntry 2 }
dot1qTpVlanPortInDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames received by this port from
its segment which were classified as belonging to this
VLAN which were discarded due to VLAN related reasons.
Specifically, the IEEE 802.1Q counters for Discard
Inbound and Discard on Ingress Filtering."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3"
::= { dot1qPortVlanStatisticsEntry 3 }
dot1qTpVlanPortInOverflowFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated
dot1qTpVlanPortInFrames counter has overflowed."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1qPortVlanStatisticsEntry 4 }
dot1qTpVlanPortOutOverflowFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated
dot1qTpVlanPortOutFrames counter has overflowed."
Bell, et al. Expires September 1999 [Page 69]
Internet Draft Bridge MIB Extensions March 1999
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1qPortVlanStatisticsEntry 5 }
dot1qTpVlanPortInOverflowDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated
dot1qTpVlanPortInDiscards counter has overflowed."
REFERENCE
"ISO/IEC 15802-3 Section 14.6.1.1.3"
::= { dot1qPortVlanStatisticsEntry 6 }
dot1qPortVlanHCStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qPortVlanHCStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing per port, per VLAN statistics for
traffic received on high capacity interfaces."
::= { dot1qVlan 7 }
dot1qPortVlanHCStatisticsEntry OBJECT-TYPE
SYNTAX Dot1qPortVlanHCStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Traffic statistics for a VLAN on a high capacity
interface."
INDEX { dot1dBasePort, dot1qVlanIndex }
::= { dot1qPortVlanHCStatisticsTable 1 }
Dot1qPortVlanHCStatisticsEntry ::=
SEQUENCE {
dot1qTpVlanPortHCInFrames
Counter64,
dot1qTpVlanPortHCOutFrames
Counter64,
dot1qTpVlanPortHCInDiscards
Counter64
}
dot1qTpVlanPortHCInFrames OBJECT-TYPE
Bell, et al. Expires September 1999 [Page 70]
Internet Draft Bridge MIB Extensions March 1999
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames received by this port from
its segment which were classified as belonging to this
VLAN. Note that a frame received on this port is
counted by this object if and only if it is for a
protocol being processed by the local forwarding process
for this VLAN. This object includes received bridge
management frames classified as belonging to this VLAN
(e.g. GMRP, but not GVRP or STP)."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3(a)"
::= { dot1qPortVlanHCStatisticsEntry 1 }
dot1qTpVlanPortHCOutFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames transmitted by this port to
its segment from the local forwarding process for this
VLAN. This includes bridge management frames originated
by this device whach are classified as belonging to this
VLAN (e.g. GMRP, but not GVRP or STP)."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3(d)"
::= { dot1qPortVlanHCStatisticsEntry 2 }
dot1qTpVlanPortHCInDiscards OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid frames received by this port from
its segment which were classified as belonging to this
VLAN which were discarded due to VLAN related reasons.
Specifically, the IEEE 802.1Q counters for Discard
Inbound and Discard on Ingress Filtering."
REFERENCE
"IEEE 802.1Q/D11 Section 12.6.1.1.3"
::= { dot1qPortVlanHCStatisticsEntry 3 }
-- -------------------------------------------------------------
Bell, et al. Expires September 1999 [Page 71]
Internet Draft Bridge MIB Extensions March 1999
-- The VLAN Learning Constraints Table
-- -------------------------------------------------------------
dot1qLearningConstraintsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot1qLearningConstraintsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing learning constraints for sets of
Shared and Independendent VLANs."
REFERENCE
"IEEE 802.1Q/D11 Section 12.10.3.1"
::= { dot1qVlan 8 }
dot1qLearningConstraintsEntry OBJECT-TYPE
SYNTAX Dot1qLearningConstraintsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A learning constraint defined for a VLAN."
INDEX { dot1qConstraintVlan, dot1qConstraintSet }
::= { dot1qLearningConstraintsTable 1 }
Dot1qLearningConstraintsEntry ::=
SEQUENCE {
dot1qConstraintVlan
VlanIndex,
dot1qConstraintSet
INTEGER,
dot1qConstraintType
INTEGER,
dot1qConstraintStatus
RowStatus
}
dot1qConstraintVlan OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of the row in dot1qVlanCurrentTable for the
VLAN constrained by this entry."
::= { dot1qLearningConstraintsEntry 1 }
dot1qConstraintSet OBJECT-TYPE
Bell, et al. Expires September 1999 [Page 72]
Internet Draft Bridge MIB Extensions March 1999
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identity of the constraint set to which
dot1qConstraintVlan belongs. These values may be chosen
by the management station."
::= { dot1qLearningConstraintsEntry 2 }
dot1qConstraintType OBJECT-TYPE
SYNTAX INTEGER {
independent(1),
shared(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of constraint this entry defines.
independent(1) - the VLAN, dot1qConstraintVlan,
uses an independent filtering database from all
other VLANs in the same set, defined by
dot1qConstraintSet.
shared(2) - the VLAN, dot1qConstraintVlan, shares
the same filtering database as all other VLANs
in the same set, defined by dot1qConstraintSet."
::= { dot1qLearningConstraintsEntry 3 }
dot1qConstraintStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this entry."
::= { dot1qLearningConstraintsEntry 4 }
dot1qConstraintSetDefault OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The identity of the constraint set to which a VLAN
belongs, if there is not an explicit entry for that VLAN
in dot1qLearningConstraintsTable."
::= { dot1qVlan 9 }
Bell, et al. Expires September 1999 [Page 73]
Internet Draft Bridge MIB Extensions March 1999
dot1qConstraintTypeDefault OBJECT-TYPE
SYNTAX INTEGER {
independent(1),
shared(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of constraint set to which a VLAN belongs, if
there is not an explicit entry for that VLAN in
dot1qLearningConstraintsTable. The types are as defined
for dot1qConstraintType."
::= { dot1qVlan 10 }
-- -------------------------------------------------------------
-- IEEE 802.1Q MIB - Conformance Information
-- -------------------------------------------------------------
qBridgeConformance OBJECT IDENTIFIER ::= { qBridgeMIB 2 }
qBridgeGroups OBJECT IDENTIFIER ::= { qBridgeConformance 1 }
qBridgeCompliances OBJECT IDENTIFIER
::= { qBridgeConformance 2 }
-- -------------------------------------------------------------
-- units of conformance
-- -------------------------------------------------------------
qBridgeBaseGroup OBJECT-GROUP
OBJECTS {
dot1qVlanVersionNumber,
dot1qMaxVlanId,
dot1qMaxSupportedVlans,
dot1qNumVlans,
dot1qGvrpStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing device level control
and status information for the Virtual LAN bridge
services."
::= { qBridgeGroups 1 }
qBridgeFdbUnicastGroup OBJECT-GROUP
Bell, et al. Expires September 1999 [Page 74]
Internet Draft Bridge MIB Extensions March 1999
OBJECTS {
dot1qFdbDynamicCount,
dot1qTpFdbPort,
dot1qTpFdbStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
unicast addresses, learnt dynamically or statically
configured by management, in each Filtering Database."
::= { qBridgeGroups 2 }
qBridgeFdbMulticastGroup OBJECT-GROUP
OBJECTS {
dot1qTpGroupEgressPorts,
dot1qTpGroupLearnt
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
multicast addresses, learnt dynamically or statically
configured by management, in each Filtering Database."
::= { qBridgeGroups 3 }
qBridgeServiceRequirementsGroup OBJECT-GROUP
OBJECTS {
dot1qForwardAllPorts,
dot1qForwardAllStaticPorts,
dot1qForwardAllForbiddenPorts,
dot1qForwardUnregisteredPorts,
dot1qForwardUnregisteredStaticPorts,
dot1qForwardUnregisteredForbiddenPorts
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
service requirements, learnt dynamically or statically
configured by management, in each Filtering Database."
::= { qBridgeGroups 4 }
qBridgeFdbStaticGroup OBJECT-GROUP
OBJECTS {
dot1qStaticUnicastAllowedToGoTo,
dot1qStaticUnicastStatus,
dot1qStaticMulticastStaticEgressPorts,
Bell, et al. Expires September 1999 [Page 75]
Internet Draft Bridge MIB Extensions March 1999
dot1qStaticMulticastForbiddenEgressPorts,
dot1qStaticMulticastStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
unicast and multicast addresses statically configured by
management, in each Filtering Database or VLAN."
::= { qBridgeGroups 5 }
qBridgeVlanGroup OBJECT-GROUP
OBJECTS {
dot1qVlanNumDeletes,
dot1qVlanFdbId,
dot1qVlanCurrentEgressPorts,
dot1qVlanCurrentUntaggedPorts,
dot1qVlanStatus,
dot1qVlanCreationTime
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
all VLANs currently configured on this device."
::= { qBridgeGroups 6 }
qBridgeVlanStaticGroup OBJECT-GROUP
OBJECTS {
dot1qVlanStaticName,
dot1qVlanStaticEgressPorts,
dot1qVlanForbiddenEgressPorts,
dot1qVlanStaticUntaggedPorts,
dot1qVlanStaticRowStatus,
dot1qNextFreeLocalVlanIndex
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
VLANs statically configured by management."
::= { qBridgeGroups 7 }
qBridgePortGroup OBJECT-GROUP
OBJECTS {
dot1qPvid,
dot1qPortAcceptableFrameTypes,
dot1qPortIngressFiltering,
Bell, et al. Expires September 1999 [Page 76]
Internet Draft Bridge MIB Extensions March 1999
dot1qPortGvrpStatus,
dot1qPortGvrpFailedRegistrations,
dot1qPortGvrpLastPduOrigin
}
STATUS current
DESCRIPTION
"A collection of objects providing port level VLAN
control and status information for all ports."
::= { qBridgeGroups 8 }
qBridgeVlanStatisticsGroup OBJECT-GROUP
OBJECTS {
dot1qTpVlanPortInFrames,
dot1qTpVlanPortOutFrames,
dot1qTpVlanPortInDiscards
}
STATUS current
DESCRIPTION
"A collection of objects providing per-port packet
statistics for all VLANs currently configured on this
device."
::= { qBridgeGroups 9 }
qBridgeVlanStatisticsOverflowGroup OBJECT-GROUP
OBJECTS {
dot1qTpVlanPortInOverflowFrames,
dot1qTpVlanPortOutOverflowFrames,
dot1qTpVlanPortInOverflowDiscards
}
STATUS current
DESCRIPTION
"A collection of objects providing per-port packet
overflow statistics for all VLANs currently configured
on this device."
::= { qBridgeGroups 10 }
qBridgeVlanHCStatisticsGroup OBJECT-GROUP
OBJECTS {
dot1qTpVlanPortHCInFrames,
dot1qTpVlanPortHCOutFrames,
dot1qTpVlanPortHCInDiscards
}
STATUS current
DESCRIPTION
"A collection of objects providing per-port packet
Bell, et al. Expires September 1999 [Page 77]
Internet Draft Bridge MIB Extensions March 1999
statistics for all VLANs currently configured on this
device for high capacity interfaces."
::= { qBridgeGroups 11 }
qBridgeLearningConstraintsGroup OBJECT-GROUP
OBJECTS {
dot1qConstraintType,
dot1qConstraintStatus
}
STATUS current
DESCRIPTION
"A collection of objects defining the Filtering Database
constraints all VLANs have with each other."
::= { qBridgeGroups 12 }
qBridgeLearningConstraintDefaultGroup OBJECT-GROUP
OBJECTS {
dot1qConstraintSetDefault,
dot1qConstraintTypeDefault
}
STATUS current
DESCRIPTION
"A collection of objects defining the default Filtering
Database constraints for VLANs which have no specific
constraints defined."
::= { qBridgeGroups 13 }
-- -------------------------------------------------------------
-- compliance statements
-- -------------------------------------------------------------
qBridgeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for device support of Virtual
LAN Bridge services."
MODULE
MANDATORY-GROUPS {
qBridgeBaseGroup,
qBridgeVlanGroup,
qBridgeVlanStaticGroup,
qBridgePortGroup
}
Bell, et al. Expires September 1999 [Page 78]
Internet Draft Bridge MIB Extensions March 1999
GROUP qBridgeFdbUnicastGroup
DESCRIPTION
"This group is mandatory for bridges that implement
802.1Q transparent bridging."
GROUP qBridgeFdbMulticastGroup
DESCRIPTION
"This group is mandatory for bridges that implement
802.1Q transparent bridging."
GROUP qBridgeServiceRequirementsGroup
DESCRIPTION
"This group is mandatory for bridges that implement
extended filtering services. All objects must be
read-write if extended-filtering services are
enabled."
GROUP qBridgeFdbStaticGroup
DESCRIPTION
"This group is optional."
GROUP qBridgeVlanStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP qBridgeVlanStatisticsOverflowGroup
DESCRIPTION
"This group is optional."
GROUP qBridgeVlanHCStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP qBridgeLearningConstraintsGroup
DESCRIPTION
"This group is mandatory for devices implementing
both Independent VLAN Learning (IVL) and Shared
VLAN Learning (SVL) modes of operation of the
filtering database."
GROUP qBridgeLearningConstraintDefaultGroup
DESCRIPTION
"This group is mandatory for devices implementing
both Independent VLAN Learning (IVL) and Shared
VLAN Learning (SVL) modes of operation of the
Bell, et al. Expires September 1999 [Page 79]
Internet Draft Bridge MIB Extensions March 1999
filtering database."
OBJECT dot1qPortAcceptableFrameTypes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dot1qPortIngressFiltering
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dot1qConstraintSetDefault
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dot1qConstraintTypeDefault
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { qBridgeCompliances 1 }
END
Bell, et al. Expires September 1999 [Page 80]
Internet Draft Bridge MIB Extensions March 1999
7. Acknowledgments
This document expands upon previous work which resulted in RFC1493.
Much of the groundwork for this document was performed by the IEEE 802.1
working group during the definition of the IEEE 802.1D updates [19] and
IEEE 802.1Q [20].
The authors wish to thank the members of the Bridge Working Group for
their many comments and suggestions which improved this effort.
8. References
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2271, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research,
January 1998
[2] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International, Hughes LAN Systems, May 1990
[3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212,
Performance Systems International, Hughes LAN Systems, March 1991
[4] M. Rose, "A Convention for Defining Traps for use with the SNMP",
RFC 1215, Performance Systems International, March 1991
[5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure
of Management Information for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1902, SNMP Research,Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International Network
Services, January 1996.
[6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
Conventions for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1903, SNMP Research, Inc., Cisco Systems, Inc.,
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance
Statements for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1904, SNMP Research, Inc., Cisco Systems, Inc.,
Bell, et al. Expires September 1999 [Page 81]
Internet Draft Bridge MIB Extensions March 1999
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, SNMP Research, Performance Systems
International, Performance Systems International, MIT Laboratory
for Computer Science, May 1990.
[9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco Systems, Inc.,
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2272, SNMP Research, Inc., Cabletron Systems,
Inc., BMC Software, Inc., IBM T. J. Watson Research, January 1998.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for
version 3 of the Simple Network Management Protocol (SNMPv3)", RFC
2274, IBM T. J. Watson Research, January 1998.
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, SNMP Research, Inc., Cisco Systems, Inc.,
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2273, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, January 1998
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2275, IBM T. J. Watson Research, BMC Software, Inc.,
Cisco Systems, Inc., January 1998
[16] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
Bell, et al. Expires September 1999 [Page 82]
Internet Draft Bridge MIB Extensions March 1999
International Organization for Standardization, International
Standard 8824, December 1987.
[17] Information processing systems - Open Systems Interconnection -
Specification of Basic Encoding Rules for Abstract Notation One
(ASN.1), International Organization for Standardization,
International Standard 8825, December 1987.
[18] ISO/IEC 10038, ANSI/IEEE Std 802.1D-1993 "MAC Bridges".
[19] "Information technology - Telecommunications and information
exchange between systems - Local and metropolitan area networks -
Common specifications - Part 3: Media Access Control (MAC) Bridges:
Revision. This is a revision of ISO/IEC 10038: 1993, 802.1j-1992
and 802.6k-1992. It incorporates P802.11c, P802.1p and P802.12e."
ISO/IEC 15802-3: 1998.
[20] ANSI/IEEE Draft Standard P802.1Q/D11, "IEEE Standards for Local and
Metropolitan Area Networks: Virtual Bridged Local Area Networks",
July 1998.
[21] Decker, E., Langille, P., Rijsinghani, A., McCloghrie, K.,
"Definitions of Managed Objects for Bridges", RFC 1493, cisco
Systems, Digital Equipment, Hughes LAN Systems, July 1993.
[22] McCloghrie, K., Kastenholz, F. "Evolution of the Interfaces Group
of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software, January
1994.
[23] Decker, E., McCloghrie, K., Langille, P., Rijsinghani, A.
"Definitions of Managed Objects for Source Routing Bridges", RFC
1525, cisco Systems, Hughes LAN Systems, Digital Equipment,
September 1993
[24] McCloghrie K., and M. Rose, Editors, "Management Information Base
for Network Management of TCP/IP-based internets", STD 17, RFC
1213, Hughes LAN Systems, Performance Systems International, March
1991.
Bell, et al. Expires September 1999 [Page 83]
Internet Draft Bridge MIB Extensions March 1999
9. Security Considerations
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and GET/SET
(read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security features
as provided by the SNMPv3 framework. Specifically, the use of the User-
based Security Model RFC 2274 [12] and the View-based Access Control
Model RFC 2275 [15] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity
giving access to an instance of this MIB, is properly configured to give
access to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete) them.
Bell, et al. Expires September 1999 [Page 84]
Internet Draft Bridge MIB Extensions March 1999
10. Authors' Addresses
Les Bell
3Com Europe Limited
3Com Centre, Boundary Way
Hemel Hempstead
Herts. HP2 7YU
UK
+44 (1442) 438025
Les_Bell@3Com.com
Andrew Smith
Extreme Networks
10460 Bandley Drive
Cupertino CA 95014
USA
+1 (408) 342 0999
andrew@extremenetworks.com
Paul Langille
Newbridge Networks
5 Corporate Drive
Andover, MA 01810
USA
+1 (978) 691 4665
langille@newbridge.com
Anil Rijhsinghani
Cabletron Systems
50 Minuteman Road
Andover MA 01810
USA
+1 (978) 684-1295
anil@cabletron.com
Keith McCloghrie
cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
+1 (408) 526 5260
kzm@cisco.com
Bell, et al. Expires September 1999 [Page 85]
Internet Draft Bridge MIB Extensions March 1999
Table of Contents
1 The SNMP Management Framework ................................... 2
2 Overview ........................................................ 4
2.1 Scope ......................................................... 4
3 Structure of MIBs ............................................... 5
3.1 Structure of Extended Bridge MIB module ....................... 5
3.1.1 Relationship to IEEE 802.1D-1998 Manageable Objects ......... 6
3.1.2 Relationship to IEEE 802.1Q Manageable Objects .............. 7
3.1.3 The dot1dExtBase Group ...................................... 8
3.1.4 The dot1dPriority Group ..................................... 8
3.1.5 The dot1dGarp Group ......................................... 8
3.1.6 The dot1dGmrp Group ......................................... 8
3.1.7 The dot1dHCPortTable ........................................ 8
3.2 Structure of Virtual Bridge MIB module ........................ 9
3.2.1 Relationship to IEEE 802.1Q Manageable Objects .............. 9
3.2.2 The dot1qBase Group ......................................... 12
3.2.3 The dot1qTp Group ........................................... 12
3.2.4 The dot1qStatic Group ....................................... 13
3.2.5 The dot1qVlan Group ......................................... 13
3.3 Textual Conventions ........................................... 13
3.4 Relationship to Other MIBs .................................... 13
3.4.1 Relationship to the 'system' group .......................... 14
3.4.2 Relation to Interfaces MIB .................................. 14
3.4.2.1 Layering Model ............................................ 15
3.4.2.2 ifStackTable .............................................. 15
3.4.2.3 ifRcvAddressTable ......................................... 16
3.4.3 Relation to Basic Bridge MIB ................................ 16
3.4.3.1 The dot1dBase Group ....................................... 16
3.4.3.2 The dot1dStp Group ........................................ 16
3.4.3.3 The dot1dTp Group ......................................... 17
3.4.3.4 The dot1dStatic Group ..................................... 17
4 Extensions to RFC 1493 .......................................... 18
5 Definitions for Extended Bridge MIB ............................. 19
6 Definitions for Virtual Bridge MIB .............................. 40
7 Acknowledgments ................................................. 81
8 References ...................................................... 81
9 Security Considerations ......................................... 84
10 Authors' Addresses ............................................. 85
Bell, et al. Expires September 1999 [Page 86]
Internet Draft Bridge MIB Extensions March 1999
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished
to others, and derivative works that comment on or otherwise
explain it or assist in its implmentation may be prepared, copied,
published and distributed, in whole or in part, without
restriction of any kind, provided that the above copyright notice
and this paragraph are included on all such copies and derivative
works. However, this document itself may not be modified in any
way, such as by removing the copyright notice or references to the
Internet Society or other Internet organizations, except as needed
for the purpose of developing Internet standards in which case the
procedures for copyrights defined in the Internet Standards
process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not
be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on
an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Bell, et al. Expires September 1999 [Page 87]
