Internet-Draft CATS Framework September 2024
Li, et al. Expires 21 March 2025 [Page]
Workgroup:
cats
Internet-Draft:
draft-ietf-cats-framework-03
Published:
Intended Status:
Informational
Expires:
Authors:
C. Li, Ed.
Huawei Technologies
Z. Du
China Mobile
M. Boucadair, Ed.
Orange
L. M. Contreras
Telefonica
J. Drake
Juniper Networks, Inc.

A Framework for Computing-Aware Traffic Steering (CATS)

Abstract

This document describes a framework for Computing-Aware Traffic Steering (CATS). Particularly, the document identifies a set of CATS components, describes their interactions, and exemplifies the workflow of the control and data planes.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 21 March 2025.

1. Introduction

Computing service architectures have been expanding from single service site to multiple, sometimes collaborative, service sites to address various issues (e.g., long response times or suboptimal service and network resource usage).

The underlying networking infrastructures that include computing resources usually provide relatively static service dispatching (that is, the selection of the service instances that will be invoked for a request). In such infrastructures, service-specific traffic is often directed to the closest service site from a routing perspective without considering the actual network state (e.g., traffic congestion conditions) or the service site state.

As described in [I-D.ietf-cats-usecases-requirements], traffic steering that takes into account computing resource metrics would benefit several services, including latency-sensitive services like immersive services that rely upon the use of augmented reality or virtual reality (AR/VR) techniques. This document provides an architectural framework that aims at facilitating the making of compute- and network-aware traffic steering decisions in networking environments where computing service resources are deployed.

The Computing-Aware Traffic Steering (CATS) framework assumes that there might be multiple service instances that are providing one given service. Each of these service instances can be accessed via a service contact instance. A single service site may have limited computing resources available at a given time, whereas the various service sites may experience different resource availability issues over time. A single service site may host one or multiple service contact instances.

Steering in CATS is about selecting the appropriate service contact instance that will service a request according to a set of network and computing metrics. That selection may not necessarily reveal the actual service instance that will be invoked, e.g., in hierarchical or recursive contexts. Therefore, the metrics of the service contact instance may be the aggregated metrics from multiple service instances.

The CATS framework is an overlay framework for the selection of the suitable service contact instance(s) from a set of candidates. The exact characterization of 'suitable' is determined by a combination of networking and computing metrics.

Also, this document describes a workflow of the main CATS procedures that are executed in both the control and data planes.

2. Terminology

This document makes use of the following terms:

Client:

An endpoint that is connected to a service provider network.

Computing-Aware Traffic Steering (CATS):

A traffic engineering approach [I-D.ietf-teas-rfc3272bis] that takes into account the dynamic nature of computing resources and network state to optimize service-specific traffic forwarding towards a given service contact instance. Various relevant metrics may be used to enforce such computing-aware traffic steering policies.

Service:

An offering that is made available by a provider by orchestrating a set of resources (networking, compute, storage, etc.).

Which and how these resources are solicited is part of the service logic which is internal to the provider. For example, these resources may be:

  • Exposed by one or multiple processes.

  • Provided by virtual instances, physical, or a combination thereof.

  • Hosted within the same or distinct nodes.

  • Hosted within the same or multiple service sites.

  • Chained to provide a service using a variety of means.

How a service is structured is out of the scope of CATS.

The same service can be provided in many locations; each of them constitutes a service instance.

Computing Service:

An offering is made available by a provider by orchestrating a set of computing resources.

CATS Service ID (CS-ID):

An identifier representing a service, which the clients use to access it. See Section 3.2.

Service instance:

An instance of running resources according to a given service logic.

Many such instances can be enabled by a provider. Instances that adhere to the same service logic provide the same service.

An instance is typically running in a service site. Clients' requests are serviced by one of these instances.

Service site:

A location that hosts the resources that are required to offer a service.

A service site may be a node or a set of nodes.

A CATS-serviced site is a service site that is connected to a CATS-Forwarder.

Service contact instance:

A client-facing service function instance that is responsible for receiving requests in the context of a given service.

A service contact instance can handle one or more service instances.

Steering beyond a service contact instance is hidden to both clients and CATS components.

A service request is processed according to the service logic (e.g., handle locally or solicit backend resources).

A service contact instance is reachable via at least one Egress CATS Forwarder.

A service can be accessed via multiple service contact instances running at the same or different locations (service sites).

A service contact instance may dispatch service requests to one or more service instances (e.g., a service contact instance that behaves as a service load-balancer).

CATS Service Contact Instance ID (CSCI-ID):

An identifier of a specific service contact instance. See Section 3.2.

Computing-aware forwarding (or steering, computing):

A forwarding (or steering, computing) scheme which takes a set of metrics that reflect the capabilities and state of computing resources as input.

Service request:

A request to access or invoke a specific service. Such a request is steered to a service contact instance via CATS-Forwarders.

A service request is placed using service-specific protocols.

Service requests are not explicitly sent by clients to CATS-Forwarders.

CATS-Forwarder:

A network entity that steers traffic specific to a service request towards a corresponding yet selected service contact instance according to provisioned forwarding decisions. These decisions are supplied by a C-PS, which may or may not be on the CATS-Forwarder.

A CATS-Forwarder may behave as Ingress or Egress CATS-Forwarder.

Ingress CATS-Forwarder:

An entity that steers service-specific traffic along a CATS-computed path that leads to an Egress CATS-Forwarder that connects to the most suitable service site that host the service contact instance selected to satisfy the initial service request.

Egress CATS-Forwarder:

An entity that is located at the end of a CATS-computed path and which connects to a CATS-serviced site.

CATS Path Selector (C-PS):

A functional entity that computes and selects paths towards service locations and instances and which accommodates the requirements of service requests. Such a path computation engine takes into account the service and network status information. See Section 3.4.4.

CATS Service Metric Agent (C-SMA):

A functional entity that is responsible for collecting service capabilities and status, and for reporting them to a CATS Path Selector (C-PS). See Section 3.4.2.

CATS Network Metric Agent (C-NMA):

A functional entity that is responsible for collecting network capabilities and status, and for reporting them to a C-PS. See Section 3.4.3.

CATS Traffic Classifier (C-TC):

A functional entity that is responsible for determining which packets belong to a traffic flow for a particular service request. It is also responsible for forwarding such packets along a C-PS computed path that leads to the relevant service contact instance. See Section 3.4.5.

3. CATS Framework and Components

3.1. Assumptions

CATS assumes that there are multiple service instances running on different service sites, and which provide a given service that is represented by the same service identifier (see Section 3.2). However, CATS does not make any assumption about these instances other than they are reachable via one or multiple service contact instances.

3.2. CATS Identifiers

CATS uses the following identifiers:

CATS Service ID (CS-ID):

An identifier representing a service, which the clients use to access it. Such an ID identifies all the instances of a given service, regardless of their location.

The CS-ID is independent of which service contact instance serves the service request.

Service requests are spread over the service contact instances that can accommodate them, considering the location of the initiator of the service request and the availability (in terms of resource/traffic load, for example) of the service instances resource-wise among other considerations like traffic congestion conditions.

CATS Service Contact Instance ID (CSCI-ID):

An identifier of a specific service contact instance.

3.3. Framework Overview

A high-level view of the CATS framework, without expanding the functional entities in the network, is illustrated in Figure 1.

   +----------------------------------+  |         +--------+
   |         Management Plane         |  |         |        |
   +----------------------------------+  |<=======>| C-SMA  |
   |           Control Plane          |  |         |        |
   +----------------------------------+  |         +---+----+
                   /\                    |             |
                   ||                    |             |
                   \/                    |             |
   +----------------------------------+  |         +--------+
   |           Data Plane             |  |         | +--------+
   +----------------------------------+  |<=======>| |Service |
                                         |         +-|Contact |
                                         |           |Instance|
                                         |           +--------+

            Network Domain                  Computing Domain
Figure 1: Main CATS Interactions

The following planes are defined:

  • CATS Management Plane: Responsible for monitoring, configuring, and maintaining CATS network devices.

  • CATS Control Plane: Responsible for scheduling services based on computing and network information. It is also responsible for making decisions about how packets should be forwarded by involved forwarding nodes and communicating such decisions to the CATS Data Plane for execution.

  • CATS Data Plane: Responsible for computing-aware routing, including handling packets in the data path, such as packet forwarding.

Depending on implementation and deployment, these planes may consist of several functional elements/components, and the details will be described in the following sections.

3.4. CATS Functional Components

CATS nodes make forwarding decisions for a given service request that has been received from a client according to the capabilities and status information of both service contact instances and network. The main CATS functional elements and their interactions are shown in Figure 2.

    +-----+              +------+           +------+
  +------+|            +------+ |         +------+ |
  |client|+            |client|-+         |client|-+
  +---+--+             +---+--+           +---+--+
      |                    |                  |
      | +----------------+ |            +-----+----------+
      +-+    C-TC#1      +-+      +-----+    C-TC#2      |
        |----------------|        |     |----------------|
        |     |C-PS#1    |    +------+  |CATS-Forwarder 4|
  ......|     +----------|....|C-PS#2|..|                |...
  :     |CATS-Forwarder 2|    |      |  |                |  .
  :     +----------------+    +------+  +----------------+  :
  :                                                         :
  :                                            +-------+    :
  :                         Underlay           | C-NMA |    :
  :                      Infrastructure        +-------+    :
  :                                                         :
  :                                                         :
  : +----------------+                +----------------+    :
  : |CATS-Forwarder 1|  +-------+     |CATS-Forwarder 3|    :
  :.|                |..|C-SMA#1|.... |                |....:
    +---------+------+  +-------+     +----------------+
              |         |             |   C-SMA#2      |
              |         |             +-------+--------+
              |         |                     |
              |         |                     |
           +------------+               +------------+
          +------------+ |             +------------+ |
          |  Service   | |             |  Service   | |
          |  Contact   | |             |  Contact   | |
          |  Instance  |-+             |  Instance  |-+
          +------------+               +------------+
           Service Site 1              Service Site 2
Figure 2: CATS Functional Components

3.4.1. Service Sites, Services Instances, and Service Contact Instances

As service instances are accessed via a service contact instance, a client will not see the service instances but only the service contact instance.

Service sites are locations that host resources (including computing resources) that are required to offer a service. As mentioned in Section 3.2, a compute service (e.g., for face recognition purposes or a game server) is uniquely identified by a CATS Service IDentifier (CS-ID). The CS-ID does not need to be globally unique, though.

A single service can be represented and accessed via several contact instances that run in same or different regions of a network.

Figure 2 shows two CATS nodes ("CATS-Forwarder 1" and "CATS-Forwarder 3") that provide access to service contact instances. These nodes behave as Egress CATS-Forwarders (Section 3.4.6).

  • Note: "Egress" is used here in reference to the direction of the service request placement. The directionality is called to explicitly identify the exit node of the CATS infrastructure.

3.4.2. CATS Service Metric Agent (C-SMA)

The CATS Service Metric Agent (C-SMA) is a functional component that gathers information about service sites and server resources, as well as the status of the different service instances. The C-SMAs may be located adjacent to the service contact instances, co-located with service contact instances, hosted by the Egress CATS-Forwarders (Section 3.4.6), etc.

Figure 2 shows one C-SMA embedded in "CATS-Forwarder 3", and another C-SMA that is adjacent to "CATS-Forwarder 1".

3.4.3. CATS Network Metric Agent (C-NMA)

The CATS Network Metric Agent (C-NMA) is a functional component that gathers information about the state of the underlay network. The C-NMAs may be implemented as standalone components or may be hosted by other components, such as CATS-Forwarders or CATS Path Selectors (C-PS) (Section 3.4.4).

C-NMA is likely to leverage existing techniques (e.g., [RFC7471], [RFC8570], and [RFC8571]).

Figure 2 shows a single, standalone C-NMA within the underlay network. There may be one or more C-NMAs for an underlay network.

3.4.4. CATS Path Selector (C-PS)

The C-SMAs and C-NMAs share the collected information with CATS Path Selectors (C-PSes) that use such information to select the Egress CATS-Forwarders (and potentially the service contact instances) where to forward traffic for a given service request. C-PSes also determine the best paths (possibly using tunnels) to forward traffic, according to various criteria that include network state and traffic congestion conditions. The collected information is encoded into one or more metrics that feed the C-PS path computation logic. Such an information also includes CS-ID and possibly CSCI-IDs.

There might be one or more C-PSes used to compute CATS paths in a CATS infrastructure.

A C-PS can be integrated into CATS-Forwarders (e.g., "C-PS#1" in Figure 2) or may be deployed as a standalone component (e.g., "C-PS#2" in Figure 2). Generally, a standalone C-PS can be a functional component of a centralized controller (e.g., a Path Computation Element (PCE) [RFC4655]).

3.4.5. CATS Traffic Classifier (C-TC)

CATS Traffic Classifier (C-TC) is a functional component that is responsible for associating incoming packets from clients with existing service requests. CATS classifiers also ensure that packets that are bound to a specific service contact instance are all forwarded towards that same service contact instance, as instructed by a C-PS.

CATS classifiers are typically hosted in CATS-Forwarders.

3.4.6. Overlay CATS-Forwarders

Egress CATS-Forwarders are the endpoints that behave as an overlay egress for service requests that are forwarded over a CATS infrastructure. A service site that hosts service instances may be connected to one or more Egress CATS-Forwarders (e.g., multi-homing design). If a C-PS has selected a specific service contact instance and the C-TC has marked the traffic with the CIS-ID related information, the Egress CATS-Forwarder then forwards traffic to the relevant service contact instance accordingly. In some cases, the choice of the service contact instance may be left open to the Egress CATS-Forwarder (i.e., traffic is marked only with the CS-ID). In such cases, the Egress CATS-Forwarder selects a service contact instance using its knowledge of service and network capabilities as well as the current load as observed by the CATS-Forwarder, among other considerations. Absent explicit policy, an Egress CATS-Forwarder must make sure to forward all packets that pertain to a given service request towards the same service contact instance.

Note that, depending on the design considerations and service requirements, per-service contact instance computing-related metrics or aggregated per-site computing related metrics (and a combination thereof) can be used by a C-PS. Using aggregated per-site computing related metrics appears as a preferred option scalability-wise, but relies on Egress CATS-Forwarders that connect to various service contact instances to select the proper service contact instance. An Egress CATS-Forwarder may choose to aggregate the metrics from different sites as well. In this case, the Egress CATS-Forwarder will choose the best site by itself when the packets arrive at it.

3.4.7. Underlay Infrastructure

The "underlay infrastructure" in Figure 2 indicates an IP and/or MPLS network that is not necessarily CATS-aware. The CATS paths that are computed by a C-PS will be distributed among the CATS-Forwarders (Section 3.4.6), and will not affect the underlay nodes. Underlay nodes are typically P routers (Section 5.3.1 of [RFC4026]).

3.5. Deployment Considerations

This document does not make any assumption about how the various CATS functional elements are implemented and deployed. Concretely, whether a CATS deployment follows a fully distributed design or relies upon a mix of centralized (e.g., a C-PS) and distributed CATS functions (e.g., CATS traffic classifiers) is deployment-specific and may reflect the savoir-faire of the (CATS) service provider.

For example, in a Centralized design, both the computing related metrics from the C-SMAs and the network metrics are collected by a (logically) centralized path computation logic (e.g., a PCE). In this case, the CATS computation logic may process incoming service requests to compute and select paths to service contact instances. More generally, the paths might be computed before the service request comes. The outcomes of such a computation process can then be communicated to CATS traffic classifiers (C-TCs).

According to the method of distributing and collecting the computing related metrics, three deployment models can be considered for the deployment of the CATS framework:

Distributed model:

Computing metrics are distributed among network devices directly using distributed protocols without interactions with a centralized control plane. Service scheduling function is performed by the CATS forwarders in the distribution model, Therefore, the C-PS is integrated into an Ingress CATS-Forwarder.

Centralized model:

Computing metrics are collected by a centralized control plane, and then the centralized control plane computes the forwarding path for service requests and syncs up with the Ingress CATS-Forwarder. In this model, C-PS is implemented in the centralized control plane.

Hybrid model:

Is a combination of distribution and centralized models.

A part of computing metrics are distributed among involved network devices, and others may be collected by a centralized control plane. For example, some static information (e.g., capabilities information) can be distributed among network devices since they are quite stable. Frequent changing information (e.g., resource utilization) can be collected by a centralized control plane to avoid frequent flooding in the distributed control plane. Service scheduling function can be performed by a centralized control plane and/or the CATS forwarder. The entire or partial C-PS function may be implemented in the centralized control plane, depending on the specific implementation and deployment.

4. CATS Framework Workflow

The following subsections provide an overview of how the CATS workflow operates.

4.1. Provisioning of CATS Components

TBC: --detail required provisioning at CAST elements (booptsrapping, credentials of peer CAST nodes, services, optimization metrics per service, etc.)--

4.2. Service Announcement

A service is associated with a unique identifier called a CS-ID. A CS-ID may be a network identifier, such as an IP address. The mapping of CS-IDs to network identifiers may be learned through a name resolution service, such as DNS [RFC1034].

4.3. Metrics Distribution

As described in Section 3.4, a C-SMA collects both service-related capabilities and metrics, and associates them with a CS-ID that identifies the service. The C-SMA may aggregate the metrics for multiple service contact instances, or maintain them separately or both.

The C-SMA then advertises CS-IDs along with metrics to related C-PSes in the network. Depending on deployment choice, CS-IDs with metrics may be distributed in different ways.

For example, in a distributed model, CS-IDs with metrics can be distributed from the C-SMA to an Egress CATS Forwarder firstly and then be redistributed by the Egress CATS Forwarder to related C-PSes that are integrated into Ingress CATS Forwarders.

In the centralized model, CS-IDs with metrics can be distributed from the C-SMA to a centralized control plane, for instance, a standalone C-PS.

In the hybrid model, the metrics can be distributed to C-PSes in combination of distributed and centralized ways.

The service metrics include computing-related metrics and potentially other service-specific metrics like the number of end-users who access the service contact instance at any given time, their location, etc.

Computing metrics may change very frequently (see [I-D.ietf-cats-usecases-requirements] for a discussion). How frequently such information is distributed is to be determined as part of the specification of any communication protocol (including routing protocols) that may be used to distribute the information. Various options can be considered, such as (but not limited to) interval-based updates, threshold-triggered updates, or policy-based updates.

Additionally, the C-NMA collects network-related capabilities and metrics. These may be collected and distributed by existing measurement protocols and/or routing protocols, although extensions to such protocols may be required to carry additional information (e.g., link latency). The C-NMA distributes the network metrics to the C-PSes so that they can use the combination of service and network metrics to determine the best Egress CATS-Forwarder to provide access to a service contact instance and invoke the compute function required by a service request. Similar to service-related metrics, the network-related metrics can be distributed using distributed, centralized, or hybrid schemes. This document does not describe such details since this is a deployment-specific.

Network metrics may also change over time. Dynamic routing protocols may take advantage of some information or capabilities to prevent the network from being flooded with state change information (e.g., Partial Route Computation (PRC) of OSPFv3 [RFC5340]). C-NMAs should also be configured or instructed like C-SMAs to determine when and how often updates should be notified to the C-PSes.

Figure 3 shows an example of how CATS metrics can be disseminated in the distributed model. There is a client attached to the network via "CATS-Forwarder 1". There are three instances of the service with CS-ID "1": two are located at "Service Site 2" attached via "CATS-Forwarder 2" and have CSCI-IDs "1" and "2"; the third service contact instance is located at "Service Site 3" attached via "CATS-Forwarder 3" and with CSCI-ID "3". There is also a second service with CS-ID "2" with only one service contact instance located at "Service Site 2".

In Figure 3, the C-SMA collocated with "CATS-Forwarder 2" distributes the service metrics for both service contact instances (i.e., (CS-ID 1, CSCI-ID 1) and (CS-ID 1, CSCI-ID 2)). Note that this information may be aggregated into a single advertisement, but in this case, the metrics for each service contact instance are indicated separately. Similarly, the C-SMA agent located at "Service Site 3" advertises the service metrics for the two services hosted by "Service Site 3".

The service metric advertisements are processed by the C-PS hosted by "CATS-Forwarder 1". The C-PS also processes network metric advertisements sent by the C-NMA. All metrics are used by the C-PS to compute and select the most relevant path that leads to the Egress CATS-Forwarder according to the initial client's service request, the service that is requested ("CS-ID 1" or "CS-ID 2"), the state of the service contact instances as reported by the metrics, and the state of the network.

          Service CS-ID 1, contact instance CSCI-ID 1 <metrics>
          Service CS-ID 1, contact instance CSCI-ID 2 <metrics>

                 :<----------------------:
                 :                       :               +---------+
                 :                       :               |CS-ID 1  |
                 :                       :            +--|CSCI-ID 1|
                 :              +----------------+    |  +---------+
                 :              |    C-SMA       |----|   Service Site 2
                 :              +----------------+    |  +---------+
                 :              |CATS-Forwarder 2|    +--|CS-ID 1  |
                 :              +----------------+       |CSCI-ID 2|
 +--------+      :                        |              +---------+
 | Client |      :  Network +----------------------+
 +--------+      :  metrics | +-------+            |
      |          : :<---------| C-NMA |            |
      |          : :        | +-------+            |
 +---------------------+    |                      |
 |CATS-Forwarder 1|C-PS|----|                      |
 +---------------------+    |       Underlay       |
                 :          |     Infrastructure   |     +---------+
                 :          |                      |     |CS-ID 1  |
                 :          +----------------------+ +---|CSCI-ID 3|
                 :                    |              |   +---------+
                 :          +----------------+  +-------+
                 :          |CATS-Forwarder 3|--| C-SMA | Service Site 3
                 :          +----------------+  +-------+
                 :                                :  |   +-------+
                 :                                :  +---|CS-ID 2|
                 :                                :      +-------+
                 :<-------------------------------:
          Service CS-ID 1, contact instance CSCI-ID 3 <metrics>
          Service CS-ID 2, <metrics>
Figure 3: An Example of CATS Metric Dessimination in a Distributed Model

The example in Figure 3 mainly describes a per-instance computing-related metric distribution. In the case of distributing aggregated per-site computing-related metrics, the per-instance CSCI-ID information will not be included in the advertisement. Instead, a per-site CSCI-ID may be used in case multiple sites are connected to the Egress CATS-Forwarder to explicitly indicate the site from where the aggregated metrics come.

If the CATS framework is implemented using a centralized model, the metric can be, e.g., distributed as illustrated in Figure 4.

                        Service CS-ID 1, instance CSCI-ID 1 <metrics>
                        Service CS-ID 1, instance CSCI-ID 2 <metrics>
                        Service CS-ID 1, instance CSCI-ID 3 <metrics>
                        Service CS-ID 2, <metrics>

             :       +------+
             :<------| C-PS |<-----------------------------------+
             :       +------+ <------+              +---------+  |
             :          ^            |           +--|CS-ID 1  |  |
             :          |            |           |  |CSCI-ID 1|  |
             :          |   +----------------+   |  +---------+  |
             :          |   |    C-SMA       |---|Service Site 2 |
             :          |   +----------------+   |  +---------+  |
             :          |   |CATS-Forwarder 2|   +--|CS-ID 1  |  |
             :          |   +----------------+      |CSCI-ID 2|  |
 +--------+  :          |             |             +---------+  |
 | Client |  :  Network |   +----------------------+             |
 +--------+  :  metrics |   | +-------+            |             |
      |      :          +-----| C-NMA |            |      +-----+
      |      :          |   | +-------+            |      |C-SMA|<-+
 +----------------+ <---+   |                      |      +-----+  |
 |CATS-Forwarder 1|---------|                      |          ^    |
 +----------------+         |       Underlay       |          |    |
             :              |     Infrastructure   |    +---------+|
             :              |                      |    |CS-ID 1  ||
             :              +----------------------+  +-|CSCI-ID 3||
             :                        |               | +---------+|
             :          +----------------+------------+            |
             :          |CATS-Forwarder 3|         Service Site 3  |
             :          +----------------+                         |
             :                        |       :      +-------+     |
             :                        +-------:------|CS-ID 2|-----+
             :                                :      +-------+
             :<-------------------------------:
      Service CS-ID 1, contact instance CSCI-ID 3
      Service CS-ID 2
Figure 4: An Example of CATS Metric Distribution in a Centralized Model

If the CATS framework is implemented using an hybrid model, the metric can be distributed, e.g., as illustrated in the Figure 5. For example, the metrics 1,2,3 associated with the CS-ID1 are collected by the centralized C-PS, and the metrics 4 and 5 are distributed via distributed protocols to the ingress CATS-Forwarder directly. For a service with CS-ID2, all the metrics are collected by the centralized C-PS. The CATS-computed path result will be distributed to the Ingress CATS-Forwarders from the C-PS by considering both the metrics from the C-SMA and C-NMA. Furthermore, the Ingress CATS-Forwarder may also have some ability to compute the path for the subsequent service accessing packets.

                   Service CS-ID 1, instance CSCI-ID 1 <metric 1,2,3>
                   Service CS-ID 1, instance CSCI-ID 2 <metric 1,2,3>
                   Service CS-ID 1, instance CSCI-ID 3 <metric 1,2,3>
                   Service CS-ID 2, <metrics>

             :       +------+
             :<------| C-PS |<-----------------------------------+
             :       +------+ <------+              +---------+  |
             :          ^            |           +--|CS-ID 1  |  |
             :          |            |           |  |CSCI-ID 1|  |
             :          |   +----------------+   |  +---------+  |
             :          |   |    C-SMA       |---|Service Site 2 |
             :          |   +----------------+   |  +---------+  |
             :          |   |CATS-Forwarder 2|   +--|CS-ID 1  |  |
             :          |   +----------------+      |CSCI-ID 2|  |
 +--------+  :          |             |             +---------+  |
 | Client |  :  Network |   +----------------------+             |
 +--------+  :  metrics |   | +-------+            |             |
      |      :          +-----| C-NMA |            |      +-----+
      |      :          |   | +-------+            |      |C-SMA|<-+
 +----------------+ <---+   |                      |      +-----+  |
 |CATS-Forwarder 1|---------|                      |          ^    |
 |----------------+         |       Underlay       |          |    |
 |C-PS|      :              |     Infrastructure   |    +---------+|
 +----+      :              |                      |    |CS-ID 1  ||
             :              +----------------------+  +-|CSCI-ID 3||
             :                        |               | +---------+|
             :          +----------------+------------+            |
             :          |CATS-Forwarder 3|         Service Site 3  |
             :          +----------------+                         |
             :                        |       :      +-------+     |
             :                        +-------:------|CS-ID 2|-----+
             :                                :      +-------+
             :<-------------------------------:
      Service CS-ID 1, contact instance CSCI-ID 3, <metric 4,5>
      Service CS-ID 2
Figure 5: An Example of CATS Metric Distribution in Hybrid Model

4.4. Service Access Processing

A C-PS computes paths that lead to Egress CATS-Forwarders according to both service and network metrics that were advertised. A C-PS may be collocated with an Ingress CATS-Forwarder (as shown in Figure 3) or logically centralized (in a centralized model or hybrid model).

This document does not specify any path computation and instance selection algorithm running in C-PSes. However, it is expected that a service request or a policy may feed the C-PS computation logic with optimization goals (e.g., in terms of maximum latency) and preferences in selecting the service contact instance.

In the example shown in Figure 3, the client sends a service access via the network through the "CATS-Forwarder 1", which is an Ingress CATS-Forwarder. Note that, a service access may consist of one or more service packets (e.g., Session Initiation Protocol (SIP) [RFC3261], HTTP [RFC9112], IPv6 [RFC8200], SRv6 [RFC8754] or Real-Time Streaming Protocol (RTSP) [RFC7826]) that carry the CS-ID and potential parameters. The Ingress CATS-Forwarder classifies the packets using the information provided by the CATS classifier (C-TC). When a matching classification entry is found for the packets, the Ingress CATS-Forwarder encapsulates and forwards them to the C-PS selected Egress CATS-Forwarder. When these packets reach the Egress CATS-Forwarder, the outer header of the possible overlay encapsulation will be removed and the inner packets will be sent to the relevant service contact instance.

  • Note that multi-homed clients may be connected to multiple CATS infrastructures that may be operated by the same or distinct service providers. This version of the framework does not cover multihoming specifics.

4.5. Service Contact Instance Affinity

Instance affinity means that packets that belong to a flow associated with a service should always be sent to the same service contact instance. Furthermore, packets of a given flow should be forwarded along the same path to avoid mis-ordering and to prevent the introduction of unpredictable latency variations. Specifically, the same Egress CATS-Forwarder may be solicited to forward the packets.

The affinity is configured on the C-PS when the service is deployed, or is determined at the time of newly formulated service requests.

Note that different services may have different notions of what constitutes a 'flow' and may, thus, identify a flow differently. Typically, a flow is identified by the 5-tuple transport coordinates (source and destination addresses, source and destination port numbers, and protocol). However, for instance, an RTP video stream may use different port numbers for video and audio channels: in that case, affinity may be identified as a combination of the two 5-tuple flow identifiers so that both flows are addressed to the same service contact instance.

Hence, when specifying a protocol to communicate information about service contact instance affinity, a certain level of flexibility for identifying flows should be supported. Or, from a more general perspective, there should be a flexible mechanism to specify and identify the set of packets that are subject to a service contact instance affinity.

More importantly, the means for identifying a flow for the purpose of ensuring instance affinity should be application-independent to avoid the need for service-specific instance affinity methods. However, service contact instance affinity information may be configurable on a per-service basis. For each service, the information can include the flow/packets identification type and means, affinity timeout value, etc.

This document does not define any mechanism for defining or enforcing service contact instance affinity.

5. Security Considerations

The computing resource information changes over time very frequently, especially with the creation and termination of service contact instances. When such an information is carried in a routing protocol, too many updates may affect network stability. This issue could be exploited by an attacker (e.g., by spawning and deleting service contact instances very rapidly). CATS solutions must support guards against such misbehaviors. For example, these solutions should support aggregation techniques, dampening mechanisms, and threshold-triggered distribution updates.

The information distributed by the C-SMA and C-NMA agents may be sensitive. Such information could indeed disclose intel about the network and the location of compute resources hosted in service sites. This information may be used by an attacker to identify weak spots in an operator's network. Furthermore, such information may be modified by an attacker resulting in disrupted service delivery for the clients, up to and including misdirection of traffic to an attacker's service implementation. CATS solutions must support authentication and integrity-protection mechanisms between C-SMAs/C-NMAs and C-PSes, and between C-PSes and Ingress CATS-Forwarders. Also, C-SMA agents need to support a mechanism to authenticate the services for which they provide information to C-PS computation logics, among other CATS functions.

6. Privacy Considerations

Means to prevent that on-path nodes in the underlay infrastructure to fingerprint and track clients (e.g., determine which client accesses which service) must be supported by CATS solutions. More generally, personal data must not be exposed to external parties by CATS beyond what is carried in the packet that was originally issued by the client.

In some cases, the service will need to know about applications, clients, and even user identity. This information is sensitive and should be encrypted. To prevent the information leaking, if the client/service communication is not already encrypted, the the C-PS computed path information should be encrypted.

For more discussion about privacy, refer to [RFC6462] and [RFC6973].

7. IANA Considerations

This document makes no requests for IANA action.

8. Informative References

[I-D.ietf-cats-usecases-requirements]
Yao, K., Trossen, D., Contreras, L. M., Shi, H., Li, Y., Zhang, S., and Q. An, "Computing-Aware Traffic Steering (CATS) Problem Statement, Use Cases, and Requirements", Work in Progress, Internet-Draft, draft-ietf-cats-usecases-requirements-03, , <https://datatracker.ietf.org/doc/html/draft-ietf-cats-usecases-requirements-03>.
[I-D.ietf-teas-rfc3272bis]
Farrel, A., "Overview and Principles of Internet Traffic Engineering", Work in Progress, Internet-Draft, draft-ietf-teas-rfc3272bis-27, , <https://datatracker.ietf.org/doc/html/draft-ietf-teas-rfc3272bis-27>.
[I-D.yao-cats-awareness-architecture]
Yao, H., wang, X., Li, Z., Huang, D., and C. Lin, "Computing and Network Information Awareness (CNIA) system architecture for CATS", Work in Progress, Internet-Draft, draft-yao-cats-awareness-architecture-02, , <https://datatracker.ietf.org/doc/html/draft-yao-cats-awareness-architecture-02>.
[RFC1034]
Mockapetris, P., "Domain names - concepts and facilities", STD 13, RFC 1034, DOI 10.17487/RFC1034, , <https://www.rfc-editor.org/rfc/rfc1034>.
[RFC3261]
Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, DOI 10.17487/RFC3261, , <https://www.rfc-editor.org/rfc/rfc3261>.
[RFC4026]
Andersson, L. and T. Madsen, "Provider Provisioned Virtual Private Network (VPN) Terminology", RFC 4026, DOI 10.17487/RFC4026, , <https://www.rfc-editor.org/rfc/rfc4026>.
[RFC4655]
Farrel, A., Vasseur, J.-P., and J. Ash, "A Path Computation Element (PCE)-Based Architecture", RFC 4655, DOI 10.17487/RFC4655, , <https://www.rfc-editor.org/rfc/rfc4655>.
[RFC5340]
Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF for IPv6", RFC 5340, DOI 10.17487/RFC5340, , <https://www.rfc-editor.org/rfc/rfc5340>.
[RFC6462]
Cooper, A., "Report from the Internet Privacy Workshop", RFC 6462, DOI 10.17487/RFC6462, , <https://www.rfc-editor.org/rfc/rfc6462>.
[RFC6973]
Cooper, A., Tschofenig, H., Aboba, B., Peterson, J., Morris, J., Hansen, M., and R. Smith, "Privacy Considerations for Internet Protocols", RFC 6973, DOI 10.17487/RFC6973, , <https://www.rfc-editor.org/rfc/rfc6973>.
[RFC7471]
Giacalone, S., Ward, D., Drake, J., Atlas, A., and S. Previdi, "OSPF Traffic Engineering (TE) Metric Extensions", RFC 7471, DOI 10.17487/RFC7471, , <https://www.rfc-editor.org/rfc/rfc7471>.
[RFC7826]
Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M., and M. Stiemerling, Ed., "Real-Time Streaming Protocol Version 2.0", RFC 7826, DOI 10.17487/RFC7826, , <https://www.rfc-editor.org/rfc/rfc7826>.
[RFC8200]
Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, , <https://www.rfc-editor.org/rfc/rfc8200>.
[RFC8570]
Ginsberg, L., Ed., Previdi, S., Ed., Giacalone, S., Ward, D., Drake, J., and Q. Wu, "IS-IS Traffic Engineering (TE) Metric Extensions", RFC 8570, DOI 10.17487/RFC8570, , <https://www.rfc-editor.org/rfc/rfc8570>.
[RFC8571]
Ginsberg, L., Ed., Previdi, S., Wu, Q., Tantsura, J., and C. Filsfils, "BGP - Link State (BGP-LS) Advertisement of IGP Traffic Engineering Performance Metric Extensions", RFC 8571, DOI 10.17487/RFC8571, , <https://www.rfc-editor.org/rfc/rfc8571>.
[RFC8754]
Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J., Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header (SRH)", RFC 8754, DOI 10.17487/RFC8754, , <https://www.rfc-editor.org/rfc/rfc8754>.
[RFC9112]
Fielding, R., Ed., Nottingham, M., Ed., and J. Reschke, Ed., "HTTP/1.1", STD 99, RFC 9112, DOI 10.17487/RFC9112, , <https://www.rfc-editor.org/rfc/rfc9112>.

Appendix A. Acknowledgements

The authors would like to thank Joel Halpern, John Scudder, Dino Farinacci, Adrian Farrel, Cullen Jennings, Linda Dunbar, Jeffrey Zhang, Peng Liu, Fang Gao, Aijun Wang, Cong Li, Xinxin Yi, Jari Arkko, Mingyu Wu, Haibo Wang, Xia Chen, Jianwei Mao, Guofeng Qian, Zhenbin Li, Xinyue Zhang, Weier Li, and Nagendra Kumar for their comments and suggestions.

Some text about various deployment models was originally documented in [I-D.yao-cats-awareness-architecture].

Contributors

Guangping Huang
ZTE
Gyan Mishra
Verizon Inc.
Huijuan Yao
China Mobile
Yizhou Li
Huawei Technologies
Dirk Trossen
Huawei Technologies
Luigi Iannone
Huawei Technologies
Hang Shi
Huawei Technologies
Changwang Lin
New H3C Technologies
Xueshun Wang
CICT
Xuewei Wang
Ruijie Networks
Christian Jacquenet
Orange

Authors' Addresses

Cheng Li (editor)
Huawei Technologies
China
Zongpeng Du
China Mobile
China
Mohamed Boucadair (editor)
Orange
France
Luis M. Contreras
Telefonica
Spain
John E Drake
Juniper Networks, Inc.
United States of America