Internet Draft Don Fedyk, Alcatel-Lucent
Category: Informational Lou Berger, LabN
Expiration Date: July 14, 2010 Loa Andersson, Ericsson AB
January 14, 2010
Generalized Multi-Protocol Label Switching (GMPLS) Ethernet
Label Switching Architecture and Framework
draft-ietf-ccamp-gmpls-ethernet-arch-09.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on July 14, 2010.
Copyright and License Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Abstract
There has been significant recent work in increasing the capabilities
of Ethernet switches and Ethernet forwarding models. As a
consequence, the role of Ethernet is rapidly expanding into
"transport networks" that previously were the domain of other
Fedyk, et. al. Informational [Page 1]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
technologies such as Synchronous Optical Network (SONET)/Synchronous
Digital Hierarchy (SDH), Time-Division Multiplex (TDM) and
Asynchronous Transfer Mode (ATM). This document defines an
architecture and framework for a Generalized MPLS based control plane
for Ethernet in this "transport network" capacity. GMPLS has already
been specified for similar technologies. Some additional extensions
to the GMPLS control plane are needed and this document provides a
framework for these extensions.
Fedyk, et. al. Informational [Page 2]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
Table of Contents
1 Introduction ........................................... 4
1.1 Terminology ............................................ 6
1.1.1 Concepts ............................................... 6
1.1.2 Abbreviations and Acronyms ............................. 7
2 Background ............................................. 8
2.1 Ethernet Switching ..................................... 8
2.2 Operations, Administration, and Maintenance (OAM) ...... 11
2.3 Ethernet Switching Characteristics ..................... 11
3 Framework .............................................. 12
4 GMPLS Routing and Addressing Model ..................... 14
4.1 GMPLS Routing .......................................... 14
4.2 Control Plane Network .................................. 15
5 GMPLS Signaling ........................................ 15
6 Link Management ........................................ 16
7 Path Computation and Selection ......................... 17
8 Multiple VLANs ......................................... 18
9 Security Considerations ................................ 18
10 IANA Considerations .................................... 19
11 References ............................................. 19
11.1 Normative References ................................... 19
11.2 Informative References ................................. 19
12 Acknowledgments ........................................ 21
13 Author's Addresses ..................................... 21
Fedyk, et. al. Informational [Page 3]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
1. Introduction
There has been significant recent work in increasing the capabilities
of Ethernet switches. As a consequence, the role of Ethernet is
rapidly expanding into "transport networks" that previously were the
domain of other technologies such as SONET/SDH, TDM and ATM. The
evolution and development of Ethernet capabilities in these areas is
a very active and ongoing process.
Multiple organizations have been active in extending Ethernet
Technology to support transport networks. This activity has taken
place in the Institute of Electrical and Electronics Engineers (IEEE)
802.1 Working Group, the International Telecommunication Union -
Telecommunication Standardization Sector (ITU-T) and the Metro
Ethernet Forum (MEF). These groups have been focusing on Ethernet
forwarding, Ethernet management plane extensions and the Ethernet
Spanning Tree Control Plane, but not on an explicitly routed,
constraint-based control plane.
In the forwarding plane context, extensions have been, or are being,
defined to support different transport Ethernet forwarding models,
protection modes, and service interfaces. Examples of such
extensions include [802.1ah], [802.1Qay], [G.8011] and [MEF.6]. These
extensions allow for greater flexibility in the Ethernet forwarding
plane and, in some cases, the extensions allow for a departure from
forwarding based on Spanning tree. For example, in the [802.1Qah]
case, greater flexibility in forwarding is achieved through the
addition of a "provider" address space. [802.1Qay] supports the use
of provisioning systems and network control protocols that explicitly
select traffic engineered paths.
This document provides a framework for GMPLS Ethernet Label Switching
(GELS). GELS will likely require more than one switching type to
support the different models, and as the GMPLS procedures that will
need to be extended are dependent on switching type, these will be
covered in the technology specific documents.
In the provider bridge model developed in the IEEE 802.1ad project
and amended to the IEEE 802.1Q standard [802.1Q], an extra Virtual
Local Area Network (VLAN) identifier (VID) is added. This VLAN is
referred to as the Service VID, (S-VID) and is carried in a Service
TAG (S-TAG). In provider backbone bridges (PBB) [802.1ah], a backbone
VID (B-VID) and B-MAC header with a service instance (I-TAG)
encapsulates a customer Ethernet frame or a service Ethernet frame.
In the IEEE 802.1Q standard the terms Provider Backbone Bridges (PBB)
and Provider Backbone Bridged Network (PBBN) are used in the context
of these extensions.
Fedyk, et. al. Informational [Page 4]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
An example of Ethernet protection extensions can be found in
[G.8031]. Ethernet operations, administration, and maintenance (OAM)
is another important area that is being extended to enable provider
Ethernet services. Related extensions can be found in [802.1ag] and
[Y.1731].
An Ethernet based service model is being defined within the context
of the MEF and ITU-T. [MEF.6] and [G.8011] provide parallel
frameworks for defining network-oriented characteristics of Ethernet
services in transport networks. These framework documents discuss
general Ethernet connection characteristics, Ethernet User-Network
Interfaces (UNIs) and Ethernet Network-Network Interfaces (NNIs).
[G.8011.1] defines the Ethernet Private Line (EPL) service and
[G.8011.2] defines the Ethernet Virtual Private Line (EVPL) service.
[MEF.6] covers both service types. These activities are consistent
with the types of Ethernet switching defined in [802.1ah].
The Ethernet forwarding and management plane extensions allow for the
disabling of standard Spanning tree but do not define an explicitly
routed, constraint-based control plane. For example [802.1Qay] is an
amendment to IEEE 802.1Q that explicitly allows for traffic
engineering of Ethernet forwarding paths.
The IETF's GMPLS work provides a common control plane for different
data plane technologies for Internet and telecommunication service
providers. The GMPLS architecture is specified in RFC3945 [RFC3945].
The protocols specified for GMPLS can be used to control "Transport
Network" technologies, e.g. Optical and TDM networks. GMPLS can also
be used for packet and Layer 2 Switching (frame/cell based networks).
This document provides a framework for use of GMPLS to control
"transport" Ethernet Label Switched Paths (Eth-LSP). Transport
Ethernet adds new constraints which require it to be distinguished
from the previously specified technologies for GMPLS. Some additional
extensions to the GMPLS control plane are needed and this document
provides a framework for these extensions. All extensions to support
Eth-LSPs will build on the GMPLS architecture and related
specifications.
This document introduces and explains GMPLS control plane use for
transport Ethernet and the concept of the Ethernet Label Switched
Path (Eth-LSP). The data plane aspects of Eth-LSPs are outside the
scope of this document and IETF activities.
The intent of this document is to reuse and align with as much of the
GMPLS protocols as possible. For example, reusing the IP control
plane addressing allows existing signaling, routing, LMP and path
computation to be used as specified. The GMPLS protocols support
Fedyk, et. al. Informational [Page 5]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
hierarchical LSPs as well as contiguous LSPs. Also, GMPLS protocol
mechanisms support a variety of network reference points from UNIs to
NNIs. Additions to existing GMPLS capabilities will only be made to
accommodate features unique to transport Ethernet.
1.1. Terminology
1.1.1. Concepts
The following are basic Ethernet and GMPLS terms:
o Asymmetric Bandwidth
This term refers to a property of a Bidirectional service
instance that has differing bandwidth allocation in each
direction.
o Bidirectional Congruent LSP
This term refers to the property of a bidirectional LSP that uses
only the same nodes, ports, and links in both directions.
Ethernet data planes are normally bidirectional congruent
(sometimes known as reverse path congruent).
o Contiguous Eth-LSP
A contiguous Eth-LSP is an end-to-end Eth-LSP that is formed from
multiple Eth-LSPs each operating within a VLAN and that are
mapped one-to-one at the VLAN boundaries. Stitched LSPs form
contiguous LSPs.
o Eth-LSP
This term refers to Ethernet label switched paths that may be
controlled via GMPLS.
o Hierarchical Eth-LSP
Hierarchical Eth-LSPs aggregate Eth-LSPs by creating a hierarchy
of Eth-LSPs.
o In-band GMPLS Signaling
In-band GMPLS Signaling is IP based control messages which are
sent on the native Ethernet links encapsulated by a single hop
Ethernet header. Logical links that use a dedicated VID on the
Fedyk, et. al. Informational [Page 6]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
same physical links would be considered In-band signaling.
o Out-of-band GMPLS Signaling
Out-of-band GMPLS Signaling is composed of IP based control
messages that are sent between Ethernet switches over links other
than the links used by the Ethernet data plane. Out of band
signaling typically shares a different fate from the data links.
o Point-to-point (P2P) Traffic Engineering (TE) service instance
A TE service instance made up of a single bidirectional P2P or
two P2P unidirectional Eth-LSPs.
o Point-to-multipoint (P2MP) Traffic Engineering (TE) service
instance
A TE service instance supported by a set of LSPs which comprises
one P2MP LSP from a root to n leaves plus a Bidirectional
Congruent point-to-point (P2P) LSP from each of the leaves to the
root.
o Shared forwarding
Shared forwarding is a property of a data path where a single
forwarding entry (VID + DMAC) may be used for frames from
multiple sources (SMAC). Shared forwarding does not change any
data plane behavior. Shared forwarding saves forwarding database
(FDB) entries only. Shared forwarding offers similar benefits to
merging in the data plane. However in shared forwarding the
Ethernet data packets are unchanged when using shared forwarding.
With shared forwarding dedicated control plane states for all
Eth-LSPs are maintained regardless of shared forwarding entries.
1.1.2. Abbreviations and Acronyms
The following abbreviations and acronyms are used in this document:
CCM Continuity Check Message
CFM Connectivity Fault Management
DMAC Destination MAC Address
Eth-LSP Ethernet Label Switched Path
I-SID Backbone Service Identifier carried in the I-TAG
I-TAG A Backbone Service Instance TAG defined in the
IEEE 802.1ah Standard [802.1ah]
LMP Link Management Protocol
Fedyk, et. al. Informational [Page 7]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
MAC Media Access Control
MP2MP Multipoint to multipoint
NMS Network Management System
OAM Operations, Administration and Maintenance
PBB Provider Backbone Bridges [802.1ah]
PBB-TE Provider Backbone Bridges Traffic Engineering
[802.1Qay]
P2P Point to Point
P2MP Point to Multipoint
QoS Quality of Service
SMAC Source MAC Address
S-TAG A Service TAG defined in the IEEE 802.1 Standard
[802.1Q]
TE Traffic Engineering
TAG An Ethernet short form for a TAG Header
TAG Header An extension to an Ethernet frame carrying
priority and other information.
TSpec Traffic specification
VID VLAN Identifier
VLAN Virtual LAN
2. Background
This section provides background to the types of switching and
services that are supported within the defined framework. The former
is particularly important as it identifies the switching functions
that GMPLS will need to represent and control. The intent is for this
document to allow for all standard forms of Ethernet switching and
services.
The material presented in this section is based on both finished and
on-going work taking place in the IEEE 802.1 Working Group, the ITU-T
and the MEF. This section references and, to some degree, summarizes
that work. This section is not a replacement for, or an
authoritative description of that work.
2.1. Ethernet Switching
In Ethernet switching terminology, the bridge relay is responsible
for forwarding and replicating the frames. Bridge relays forward
frames based on the Ethernet header fields: Virtual Local Area
Network (VLAN) Identifiers (VID) and Destination Media Access Control
(DMAC) address. PBB [802.1ah] has also introduced a Service Instance
tag (I-TAG). Across all the Ethernet extensions (already referenced
in the Introduction), multiple forwarding functions, or service
interfaces, have been defined using the combination of VIDs, DMACs,
Fedyk, et. al. Informational [Page 8]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
and I-TAGs. PBB [802.1ah] provides a breakdown of the different
types of Ethernet switching services. Figure 1 reproduces this
breakdown.
PBB Network
Service Types
_,,-' | '--.._
_,.-'' | `'--.._
_,.--' | `'--..
Port based S-tagged I-tagged
_,- -.
_.' `.
_,' `.
one-to-one bundled
_.- =.
_.-' ``-.._
_.-' `-..
many-to-one all-to-one
|
|
|
Transparent
Figure 1: Ethernet Switching Service Types
The switching types are defined in Clause 25 of [802.1ah]. While not
specifically described in [802.1ah], the Ethernet services being
defined in the context of [MEF.6] and [G.8011] also fall into the
types defined in Figure 1 (with the exception of the newly defined I-
tagged service type).
[802.1ah] defines a new I-tagged service type but does not
specifically define the Ethernet services being defined in the
context of [MEF.6] and [G.8011] which are also illustrated in Figure
1.
To summarize the definitions:
o Port based
This is a frame based service that supports specific frame types,
no Service VLAN tagging or MAC address based switching.
o S-tagged
There are multiple Service VLAN tag (S-tag) aware services,
including:
+ one-to-one
In this service, each VLAN identifier (VID) is mapped into a
Fedyk, et. al. Informational [Page 9]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
different service.
+ Bundled
Bundled S-tagged service supports the mapping of multiple VIDs
into a single service and include:
* many-to-one
In this frame based service, multiple VIDs are mapped into the
same service.
* all-to-one
In this frame based service, all VIDs are mapped into the same
service.
- transparent
This is a special case, all frames are mapped from a single
incoming port to a single destination Ethernet port.
o I-tagged
The edge of a PBBN consists of a combined backbone relay (B-
component relay) and service instance relay (I-component relay).
An I-Tag contains a service identifier (24 bit I-SID) and priority
markings as well as some other fields. An I-Tagged service is
typically between the edges of the PBBN and terminated at each edge
on an I-component that faces a customer port so the service is
often not visible except at the edges. However, since the I-
component relay involves a distinct relay, it is possible to have a
visible I-Tagged Service by separating the I component relay from
the B-component relay. Two examples where it makes sense to do
this are: an I-Tagged service between two PBBNs and as an
attachment to a customer's Provider Instance Port.
In general, the different switching types determine which of the
Ethernet header fields are used in the forwarding/switching function,
e.g. VID only or VID and DMACs. The switching type may also require
the use of additional Ethernet headers or fields. Services defined
for UNIs tend to use the headers for requesting service (service
delimiter) and are relevant between the customer site and network
edge.
In most bridging cases, the header fields cannot be changed, but some
translations of VID field values are permitted, typically at the
network edges.
Across all service types, the Ethernet data plane is bidirectional
congruent. This means that the forward and reverse paths share the
exact same set of nodes, ports and bidirectional links. This
Fedyk, et. al. Informational [Page 10]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
property is fundamental. The 802.1 group has maintained this
bidirectional congruent property in the definition of Connectivity
Fault Management (CFM) which is part of the overall Operations
Administration and Maintenance (OAM) capability.
2.2. Operations, Administration, and Maintenance (OAM)
Robustness is enhanced with the addition of data plane OAM to provide
both fault and performance management.
Ethernet OAM messages [802.1ag] and [Y.1731], rely on data plane
forwarding for both directions. Determining a broken path or
misdirected packet in this case relies on OAM following the Eth-LSP.
These OAM message identifiers are dependent on the data plane so they
work equally well for provisioned or GMPLS controlled paths.
Ethernet OAM currently consists of:
Defined in both [802.1ag & Y.1731]:
- CCM/RDI: Connectivity Check, Remote Defect Indication
- LBM/LBR: Loopback Message, Loopback Reply
- LTM/LTR: Link trace Message, Link trace Reply
- VSM/VSR: Vendor-specific extensions Message/Reply
Additionally defined in [Y.1731]:
- AIS: Alarm Indication Signal
- LCK: Locked Signal
- TST: Test
- LMM/LMR: Loss Measurement Message/Reply
- DM/DMM/DMR: Delay Measurement
- EXM/EXR: Experimental
- APS, MCC: Automatic Protection Switching, Maintenance
Communication Channel
These functions are supported across all the Standardized Eth-LSP
formats.
2.3. Ethernet Switching Characteristics
Ethernet is similar to MPLS as it encapsulates different packet and
frame types for data transmission. In Ethernet, the encapsulated
data is referred to as MAC client data. The encapsulation is an
Ethernet MAC frame with a header, a source address, destination
address, optional VLAN identifier, Type and length on the front of
the MAC client data with optional padding and a Frame Check Sequence
at the end of the frame.
Fedyk, et. al. Informational [Page 11]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
The type of MAC client data is typically identified by an "Ethertype"
value. This is an explicit type indication but Ethernet also supports
an implicit type indication.
Ethernet bridging switches based on a frame's destination MAC address
and VLAN. The VLAN identifies a virtual active set of Bridges and
LANs. The address is assumed to be unique and invariant within the
VLAN. MAC addresses are often globally unique but this is not
necessary for bridging.
3. Framework
As defined in the GMPLS Architecture [RFC3945], the GMPLS control
plane can be applied to a technology by controlling the data plane
and switching characteristics of that technology. The GMPLS
architecture, per [RFC3945], allowed for control of Ethernet bridges
and other layer 2 technologies using the Layer-2 Switch Capable
(L2SC) switching type. But, the control of Ethernet switching was
not explicitly defined in [RFC3471], [RFC4202] or any other
subsequent GMPLS reference document.
The GMPLS architecture includes a clear separation between a control
plane and a data plane. Control plane and data plane separation
allows the GMPLS control plane to remain architecturally and
functionally unchanged while controlling different technologies. The
architecture also requires IP connectivity for the control plane to
exchange information, but does not otherwise require an IP data
plane.
All aspects of GMPLS, i.e., addressing, signaling, routing and link
management, may be applied to Ethernet switching. GMPLS can provide
control for traffic engineered and protected Ethernet service paths.
This document defines the term "Eth-LSP" to refer to Ethernet service
paths that are controlled via GMPLS. As is the case with all GMPLS
controlled services, Eth-LSPs can leverage common traffic engineering
attributes such as:
- bandwidth profile;
- forwarding priority level;
- connection preemption characteristics;
- protection/resiliency capability;
- routing policy, such as an explicit route;
- bidirectional service;
- end-to-end and segment protection;
- hierarchy
The bandwidth profile may be used to set committed information rate,
Fedyk, et. al. Informational [Page 12]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
peak information rate, and policies based on either under-
subscription or over-subscription. Services covered by this
framework will use a TSpec that follows the Ethernet Traffic
parameters defined in [ETH-TSPEC].
In applying GMPLS to "transport" Ethernet, GMPLS will need to be
extended to work with the Ethernet data plane and switching
functions. The definition of GMPLS support for Ethernet is multi-
faceted due to the different forwarding/switching functions inherent
in the different service types discussed in Section 2.1. In general,
the header fields used in the forwarding/switching function, e.g. VID
and DMAC, can be characterized as a data plane label. In some
circumstances these fields will be constant along the path of the
Eth-LSP, and in others they may vary hop-by-hop or at certain
interfaces only along the path. In the case where the "labels" must
be forwarded unchanged, there are a few constraints on the label
allocation that are similar to some other technologies such as lambda
labels.
The characteristics of the "transport" Ethernet data plane are not
modified in order to apply GMPLS control. For example, consider the
IEEE 802.1Q [802.1Q] data plane: The VID is used as a "filter"
pointing to a particular forwarding table, and if the DMAC is found
in that forwarding table the forwarding decision is taken based on
the DMAC. When forwarding using an Spanning tree, if the DMAC is not
found the frame is broadcast over all outgoing interfaces for which
that VID is defined. This valid MAC checking and broadcast supports
Ethernet learning. A special case is when a VID is defined for only
two ports on one bridge, effectively resulting in a p2p forwarding
constraint. In this case all frames tagged with that VID received
over one of these ports are forward over the other port without
address learning.
[802.1Qay] allows for turning off learning and hence the broadcast
mechanism providing means to create explicitly routed Ethernet
connections.
This document does not define any specific format for an Eth-LSP
label. Rather, it is expected that service specific documents will
define any signaling and routing extensions needed to support a
specific Ethernet service. Depending on the requirements of a
service, it may be necessary to define multiple GMPLS protocol
extensions and procedures. It is expected that all such extensions
will be consistent with this document.
It is expected that a key requirement for service specific documents
will be to describe label formats and encodings. It may also be
necessary to provide a mechanism to identify the required Ethernet
Fedyk, et. al. Informational [Page 13]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
service type in signaling and a way to advertise the capabilities of
Ethernet switches in the routing protocols. These mechanisms must
make it possible to distinguish between requests for different
paradigms including new, future, and existing paradigms.
The Switching Type and Interface Switching Capability Descriptor
share a common set of values and are defined in [RFC3945], [RFC3471],
and [RFC4202] as indicators of the type of switching that should
([RFC3471]) and can ([RFC4202]) be performed on a particular link for
an LSP. The L2SC switching type may already be used by
implementations performing layer 2 switching including Ethernet. As
such, and to allow the continued use of that switching type and those
implementations, and to distinguish the different Ethernet switching
paradigms, a new switching type needs to be defined for each new
Ethernet switching paradigm that is supported.
For discussion purposes, we decompose the problem of applying GMPLS
into the functions of Routing, Signaling, Link Management and Path
Selection. It is possible to use some functions of GMPLS alone or in
partial combinations. In most cases using all functions of GMPLS
leads to less operational overhead than partial combinations.
4. GMPLS Routing and Addressing Model
The GMPLS routing and addressing model is not modified by this
document. GMPLS control for Eth-LSPs uses the routing and Addressing
Model described in [RFC3945]. Most notably this includes the use of
IP addresses to identify interfaces and LSP end-points. It also
includes support for both numbered and unnumbered interfaces.
In the case where another address family or type of identifier is
required to support an Ethernet service, extensions may be defined to
provide mapping to an IP address. Support of Eth-LSPs is expected to
strictly comply to the GMPLS protocol suite addressing as specific in
[RFC3471], [RFC3473] and related documents.
4.1. GMPLS Routing
GMPLS routing as defined in [RFC4202] uses IP routing protocols with
opaque TLV extensions for the purpose of distributing GMPLS related
TE (router and link) information. As is always the case with GMPLS,
TE information is populated based on resource information obtained
from LMP or from configured information. The bandwidth resources of
the links are tracked as Eth-LSPs are set up. Interfaces supporting
the switching of Eth-LSPs are identified using the appropriate
Interface Switching Capabilities Descriptor. As mentioned in Section
Fedyk, et. al. Informational [Page 14]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
3, the definition of one or more new Interface Switching Capabilities
to support Eth-LSPs is expected. Again, the L2SC Interface Switching
Capabilities will not be used to represent interfaces capable of
supporting Eth-LSPs defined by this document and subsequent documents
in support of the transport Ethernet switching paradigms. In
addition, Interface Switching Capability specific TE information may
be defined as needed to support the requirements of a specific
Ethernet Switching Service Type.
GMPLS routing is an optional functionality but it is highly valuable
in maintaining topology and distributing the TE database for path
management and dynamic path computation.
4.2. Control Plane Network
In order for a GMPLS control plane to operate, an IP connectivity
network of sufficient capacity to handle the information exchange of
the GMPLS routing and signaling protocols is necessary.
One way to implement this is with an IP routed network supported by
an IGP that views each switch as a terminated IP adjacency. In other
words, IP traffic and a simple routing table are available for the
control plane but there is no requirement for needing a high
performance IP data plane, or for forwarding user traffic over this
IP network.
This IP connectivity can be provided as a separate independent
network (out of band) or integrated with the Ethernet switches (in-
band).
5. GMPLS Signaling
GMPLS signaling, see [RFC3471][RFC3473], is well suited to the
control of Eth-LSPs and Ethernet switches. Signaling provides the
ability to dynamically establish a path from an ingress node to an
egress node. The signaled path may be completely static and not
change for the duration of its lifetime. However, signaling also has
the capability to dynamically adjust the path in a coordinated
fashion after the path has been established. The range of signaling
options from static to dynamic are under operator control.
Standardized signaling also improves multi-vendor interoperability.
GMPLS signaling supports the establishment and control of
bidirectional and unidirectional data paths. Ethernet is
bidirectional by nature and CFM has been built to leverage this.
Prior to CFM, the emulation of a physical wire and the learning
Fedyk, et. al. Informational [Page 15]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
requirements also mandated bidirectional connections. Given this,
Eth-LSPs need to be bidirectional congruent. Eth-LSPs may be either
P2P or P2MP (see [RFC4875]). GMPLS signaling also allows for full
and partial LSP protection; see [RFC4872] and [RFC4873].
Note that standard GMPLS does not support different bandwidth in each
direction of a bidirectional LSP. [RFC5467], an Experimental
document, provides procedures if asymmetric bandwidth bidirectional
LSPs are required.
6. Link Management
Link discovery has been specified for links interconnecting IEEE
802.1 bridges in [802.1AB]. The benefits of running link discovery
in large systems are significant. Link discovery may reduce
configuration and reduce the possibility of undetected errors in
configuration as well as exposing misconnections. However the 802.1AB
capability is an optional feature, it is not necessarily operating
before a link is operational, and it primarily supports the
management plane.
In the GMPLS context, LMP [RFC4204] has been defined to support GMPLS
control plane link management and discovery features. LMP also
supports for the control plane the automated creation of unnumbered
interfaces. If LMP is not used there is an additional configuration
requirement for GMPLS link identifiers. For large-scale
implementations LMP is beneficial. LMP also has optional fault
management capabilities, primarily for opaque and transparent network
technology. With IEEE's newer CFM [802.1ag] and ITU-T's [Y.1731]
capabilities, this optional capability may not be needed. It is the
goal of the GMPLS Ethernet architecture to allow the selection of the
best tool set for the user needs. The full functionality of Ethernet
CFM should be supported when using a GMPLS control plane.
LMP and 802.1AB are relatively independent. The LMP capability should
be sufficient to remove the need for 802.1AB but 802.1 AB can be run
in parallel or independently if desired. Figure 2 provides possible
ways of using LMP, 802.1AB and 802.1ag in combination.
Figure 2 illustrates the functional relationship of link management
and OAM schemes. It is expected that LMP would be used for control
plane functions of link property correlation but that Ethernet
mechanisms for OAM such as CFM, link trace, etc. would be used for
data plane fault management and fault trace.
Fedyk, et. al. Informational [Page 16]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
+-------------+ +-------------+
| +---------+ | | +---------+ |
| | | | | | | |GMPLS
| | LMP |-|<------>|-| LMP | |Link Property
| | | | | | | |Correlation
| | (opt) | |GMPLS | | (opt) | |
| | | | | | | | Bundling
| +---------+ | | +---------+ |
| +---------+ | | +---------+ |
| | | | | | | |
| | 802.1AB |-|<------>|-| 802.1AB | |P2P
| | (opt) | |Ethernet| | (opt) | |link identifiers
| | | | | | | |
| +---------+ | | +---------+ |
| +---------+ | | +---------+ |
| | | | | | | |End to End
-----|-| 802.1ag |-|<------>|-| 802.1ag |-|-------
| | Y.1731 | |Ethernet| | Y.1731 | |Fault Management
| | (opt) | | | | (opt) | |Performance
| | | | | | | |Management
| +---------+ | | +---------+ |
+-------------+ +-------------+
Switch 1 link Switch 2
Figure 2: Logical Link Management Options
7. Path Computation and Selection
GMPLS does not specify a specific method for selecting paths or
supporting path computation. GMPLS allows for a wide range of
possibilities supported from very simple path computation to very
elaborate path coordination where a large number of coordinated paths
are required. Path computation can take the form of paths being
computed in a fully distributed fashion, on a management station with
local computation for rerouting, or on more sophisticated path
computation servers.
Eth-LSPs may be supported using any path selection or computation
mechanism. As is the case with any GMPLS path selection function, and
common to all path selection mechanisms, the path selection process
should take into consideration Switching Capabilities and Encoding
advertised for a particular interface. Eth-LSPs may also make use of
the emerging path computation element and selection work; see
[RFC4655].
Fedyk, et. al. Informational [Page 17]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
8. Multiple VLANs
This document allows for the support of the signaling of Ethernet
parameters across multiple VLANs supporting both contiguous Eth-LSP
and Hierarchical Ethernet LSPs. The intention is to reuse GMPLS
hierarchy for the support of Peer to Peer models, UNIs and NNIs.
9. Security Considerations
A GMPLS controlled "transport" Ethernet system should assume that
users and devices attached to UNIs may behave maliciously,
negligently, or incorrectly. Intra-provider control traffic is
trusted to not be malicious. In general, these requirements are no
different from the security requirements for operating any GMPLS
network. Access to the trusted network will only occur through the
protocols defined for the UNI or NNI or through protected management
interfaces.
When in-band GMPLS signaling is used for the control plane the
security of the control plane and the data plane may affect each
other. When out-of-band GMPLS signaling is used for the control
plane the data plane security is decoupled from the control plane and
therefore the security of the data plane has less impact on overall
security.
Where GMPLS is applied to the control of VLAN only, the commonly
known techniques for mitigation of Ethernet DOS attacks may be
required on UNI ports.
For a more comprehensive discussion on GMPLS security please see the
MPLS and GMPLS Security Framework [SECURITY]. Cryptography can be
used to protect against many attacks described in [SECURITY]. One
option for protecting "transport" Ethernet is the use of 802.1AE
Media Access Control Security, [MACSEC] which provides encryption and
authentication."
It is expected that solution documents will include a full analysis
of the security issues that any protocol extensions introduce.
Fedyk, et. al. Informational [Page 18]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
10. IANA Considerations
No new values are specified in this document.
11. References
11.1. Normative References
[RFC3471] Berger, L. (editor), "Generalized MPLS Signaling
Functional Description", January 2003, RFC3471.
[RFC3473] Berger, L. (editor), "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Resource ReserVation
Protocol-Traffic Engineering (RSVP-TE) Extensions",
January 2003, RFC3473.
[RFC4202] Kompella, K., Rekhter, Y., "Routing Extensions in
Support of Generalized MPLS", RFC 4202, October 2005
[RFC3945] E. Mannie, Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Architecture", RFC 3495.
11.2. Informative References
[G.8031] ITU-T Draft Recommendation G.8031, Ethernet Protection
Switching.
[G.8011] ITU-T Draft Recommendation G. 8011, Ethernet over
Transport - Ethernet services framework.
[802.1AB] "IEEE Standard for Local and Metropolitan Area
Networks, Station and Media Access Control
Connectivity Discovery" (2004).
[802.1ag] "IEEE Standard for Local and Metropolitan Area
Networks - Virtual Bridged Local Area Networks
- Amendment 5:Connectivity Fault Management",
(2007).
[802.1ah] "IEEE Standard for Local and Metropolitan Area
Networks - Virtual Bridged Local Area Networks
- Amendment 6: Provider Backbone Bridges",
IEEE Std 802.1Qah-2008, 14 August 2008.
Fedyk, et. al. Informational [Page 19]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
[802.1Qay] "IEEE Standard for Local and Metropolitan Area
Networks - Virtual Bridged Local Area Networks
Provider Backbone Bridge Traffic Engineering
- Amendment 10: ", IEEE Std 802.1Qay-2009,
August 5th, 2009.
[802.1Q] "IEEE standard for Virtual Bridged Local Area Networks
802.1Q-2005", May 19, 2006.
[RFC4204] Lang. J. Editor, "Link Management Protocol (LMP)"
RFC4204, October 2005.
[MEF.6] The Metro Ethernet Forum MEF 6 (2004), "Ethernet Services
Definitions - Phase I".
[MEF.10] The Metro Ethernet Forum MEF 10 (2004), "Ethernet
Services Attributes Phase 1".
[RFC4875] Aggarwal, R. Ed., "Extensions to RSVP-TE for Point to
Multipoint TE LSPs", IETF RFC 4875, May 2007.
[RFC4655] Farrel, A. et.al., "Path Computation Element (PCE)
Architecture", RFC 4655, August 2006.
[RFC4872] Lang et.al., "RSVP-TE Extensions in support of
End-to-End Generalized Multi-Protocol Label Switching
(GMPLS)-based Recovery ", RFC 4872, May 2007.
[RFC4873] Berger, L. et.al.,"MPLS Segment Recovery", RFC 4873, May
2007.
[Y.1731] ITU-T Draft Recommendation Y.1731(ethoam), " OAM
Functions and Mechanisms for Ethernet based Networks ",
work in progress.
[RFC5467] Berger, L. et al., "GMPLS Asymmetric Bandwidth
Bidirectional LSPs", RFC5467, March 2009.
[ETH-TSPEC] Papadimitriou, D., "Ethernet Traffic Parameters",
draft-ietf-ccamp-ethernet-traffic-parameters-09.txt,
work in progress.
[SECURITY] Luyuan Fang, Ed., "Security Framework for MPLSand GMPLS
Networks", draft-ietf-mpls-mpls-and-gmpls-security-
framework-07.txt, work in progress.
Fedyk, et. al. Informational [Page 20]
Internet-Draft draft-ietf-ccamp-gmpls-ethernet-arch-09.txt Jan. 14, 2010
[MACSEC] "IEEE Standard for Local and metropolitan area networks
Media Access Control (MAC) Security
IEEE 802.1AE-2006", August 18, 2006.
12. Acknowledgments
There were many people involved in the initiation of this work prior
to this document. The GELS framework draft and the PBB-TE extensions
drafts were two drafts the helped shape and justify this work. We
acknowledge the work of these authors of these initial drafts:
Dimitri Papadimitriou, Nurit Sprecher, Jaihyung Cho, Dave Allan,
Peter Busschbach, Attila Takacs, Thomas Eriksson, Diego Caviglia,
Himanshu Shah, Greg Sunderwood, Alan McGuire, and Nabil Bitar.
George Swallow contributed significantly to this document.
13. Author's Addresses
Don Fedyk
Alcatel-Lucent
Groton, MA, 01450
Phone: +1-978-467-5645
Email: donald.fedyk@alcatel-lucent.com
Lou Berger
LabN Consulting, L.L.C.
Phone: +1-301-468-9228
Email: lberger@labn.net
Loa Andersson
Ericsson AB
Phone: +46 10 717 52 13
Email: loa.andersson@ericsson.com
Fedyk, et. al. Informational [Page 21]
Generated on: Thu Jan 14 15:15:38 EST 2010
