CCAMP Working Group                                     Thomas D. Nadeau
Internet Draft                                       Cisco Systems, Inc.
Proposed Status: Standards Track
Expires: December 2004                                 Cheenu Srinivasan
                                                          Bloomberg L.P.

                                                           Adrian Farrel
                                                      Old Dog Consulting

                                                                Tim Hall
                                                             Ed Harrison
                                                    Data Connection Ltd.


                                                               June 2004


      Generalized Multiprotocol Label Switching (GMPLS) Traffic
               Engineering Management Information Base

                draft-ietf-ccamp-gmpls-te-mib-05.txt


Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Abstract

   This memo defines an experimental portion of the Management
   Information Base (MIB) for use with network management protocols in
   the Internet community. In particular, it describes managed objects
   for Generalized Multiprotocol Label Switching (GMPLS) based traffic
   engineering.





Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 1]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

Table of Contents

   1. Introduction                                             2
   1.1. Migration Strategy                                     3
   2. Terminology                                              3
   3. The SNMP Management Framework                            3
   4. Outline                                                  4
   4.1. Summary of GMPLS Traffic Engineering MIB Module        4
   5. Brief Description of GMPLS TE MIB Objects                4
   5.1. gmplsTunnelTable                                       4
   5.2. gmplsTunnelHopTable                                    5
   5.3. gmplsTunnelARHopTable                                  5
   5.4. gmplsTunnelCHopTable                                   5
   5.5. gmplsTunnelErrorTable                                  5
   5.6. gmplsTunnelReversePerfTable                            5
   6. Cross-referencing to the mplsLabelTable                  5
   7. Example of GMPLS Tunnel Setup                            6
   8. GMPLS Traffic Engineering MIB Definitions                9
   9. Security Considerations                                 37
   10. Acknowledgments                                        38
   11. References                                             39
   11.1. Normative Refenerces                                 39
   11.2. Informational References                             40
   12. Authors' Addresses                                     41
   13. Full Copyright Statement                               41
   14. Intellectual Property Notice                           42


1. Introduction

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes managed objects for modeling a
   Generalized Multiprotocol Label Switching (GMPLS) [GMPLSArch] based
   traffic engineering. The tables and objects defined in this document
   extend those defined in the equivalent document for MPLS traffic
   engineering [TEMIB], and management of GMPLS traffic engineering is
   built on management of MPLS traffic engineering.

   This MIB module should be used in conjunction with the companion
   document [GMPLSLSRMIB] for GMPLS based traffic engineering
   configuration and management.

   Comments should be made direct to the CCAMP mailing list at
   ccamp@ops.ietf.org.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119, reference
   [RFC2119].








Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 2]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

1.1. Migration Strategy

   This MIB module extends the traffic engineering MIB module defined
   for use with MPLS [TEMIB]. It provides additions for support of GMPLS
   tunnels.

   The companion document for modeling and managing GMPLS based LSRs
   [GMPLSLSRMIB] extends MPLS LSR MIB [LSRMIB] with the same intentions.

   Textual conventions and OBJECT-IDENTIFIERS are defined in [TCMIB] and
   [GMPLSTCMIB].

2. Terminology

   This document uses terminology from the MPLS architecture document
   [RFC3031], from the GMPLS architecture document [GMPLSArch], and from
   the MPLS Traffic Engineering MIB [TEMIB]. Some frequently used terms
   are described next.

   An explicitly routed LSP (ERLSP) is referred to as a GMPLS tunnel. It
   consists of in-segment(s) and/or out-segment(s) at the egress/ingress
   LSRs, each segment being associated with one GMPLS enabled interface.
   These are also referred to as tunnel segments.

   Additionally, at an intermediate LSR, we model a connection as
   consisting of one or more in-segments and/or one or more out-
   segments. The binding or interconnection between in-segments and out-
   segments in performed using a cross-connect.

   These segment and cross-connect objects are defined in the MPLS Label
   Switch Router MIB [LSRMIB], but see also the GMPLS Label Switch
   Router MIB [GMPLSLSRMIB] for the GMPLS-specific extensions to these
   objects.

3. The SNMP Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a
   MIB module that is compliant to the SMIv2, which is described in STD
   58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
   2580 [RFC2580].










Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 3]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

4. Outline

   Support for GMPLS traffic-engineered tunnels requires the following
   configuration.

   - Setting up tunnels with appropriate MPLS configuration parameters
     using [TEMIB].
   - Extending the tunnels with GMPLS configuration parameters.
   - Configuring tunnel loose and strict source routed hops.

   These actions may need to be accompanied with corresponding actions
   using [LSRMIB] and [GMPLSLSRMIB] to establish and configure tunnel
   segments, if this is done manually. Also, the in-segment and out-
   segment performance tables, mplsInSegmentPerfTable and
   mplsOutSegmentPerfTable [LSRMIB], should be used to determine
   performance of the tunnels and tunnel segments although it should be
   noted that those tables may not be appropriate for measuring
   performance on some types of GMPLS links.

4.1. Summary of GMPLS Traffic Engineering MIB Module

   The MIB objects for performing the actions listed above that cannot
   be performed solely using the MIB objects defined in [TEMIB] consist
   of the following tables.

   - Tunnel Table (gmplsTunnelTable) for providing GMPLS-specific
     tunnel configuration parameters.
   - Tunnel specified, actual, and computed hop tables
     (gmplsTunnelHopTable, gmplsTunnelARHopTable, and
     gmplsTunnelCHopTable) for providing additional configuration of
     strict and loose source routed tunnel hops.
   - Performance and error reporting tables (gmplsTunnelReversePerfTable
     and gmplsTunnelErrorTable).

   These tables are described in the subsequent sections.

   Additionally, this MIB module contains a new Notification.

   - The GMPLS Tunnel Down Notification (gmplsTunnelDown) is intended to
     be used in place of the mplsTunnelDown Notification defined in
     [TEMIB]. As well as indicating that a tunnel has transitioned to
     operational down state, this new Notificaiton indicates the cause
     of the failure.

5. Brief Description of GMPLS TE MIB Objects

   The objects described in this section support the functionality
   described in [RFC3473] and [RFC3472] for GMPLS tunnels.
   The tables support both manually configured and signaled tunnels.

5.1. gmplsTunnelTable

   The gmplsTunnelTable extends the MPLS traffic engineering MIB to
   allow GMPLS tunnels to be created between an LSR and a remote
   endpoint, and existing GMPLS tunnels to be reconfigured or removed.



Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 4]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   Note that we only support point-to-point tunnel segments, although
   multi-point-to-point and point-to-multi-point connections are
   supported by an LSR acting as a cross-connect.

   Each tunnel can thus have one out-segment originating at an LSR
   and/or one in-segment terminating at that LSR.

5.2. gmplsTunnelHopTable

   The gmplsTunnelHopTable is used to indicate additional parameters for
   the hops, strict or loose, of a GMPLS tunnel defined in
   gmplsTunnelTable, when it is established using signaling.  Multiple
   tunnels may share the same hops by pointing to the same entry in this
   table.

5.3. gmplsTunnelARHopTable

   The gmplsTunnelARHopTable is used to indicate the actual hops
   traversed by a tunnel as reported by the signaling protocol after the
   tunnel is setup.  The support of this table is optional since not all
   GMPLS signaling protocols support this feature.

5.4. gmplsTunnelCHoptable

   The gmplsTunnelCHopTable lists the actual hops computed by a
   constraint-based routing algorithm based on the gmplsTunnelHopTable.
   The support of this table is optional since not all implementations
   support computation of hop lists using a constraint-based routing
   protocol.

5.5. gmplsTunnelErrorTable

   The gmplsTunnelErrorTable provides access to information about the
   last error that occurred on each tunnel known about by the MIB.  It
   indicates the nature of the error, when and how it was reported and
   can give recovery advice through a display string.

5.6. gmplsTunnelReversePerfTable

   gmplsTunnelReversePerfTable provides additional counters to measure
   the performance of bidirectional GMPLS tunnels in which packets are
   visible. It supplements the counters in mplsTunnelPerfTable and
   augments gmplsTunnelTable.

   Note that not all counters may be appropriate or available for some
   types of tunnel.

6. Cross-referencing to the gmplsLabelTable

   The gmplsLabelTable is found in a MIB module in [GMPLSLSRMIB] and
   provides a way to model labels in a GMPLS system where labels might
   not be simple 32 bit integers.

   The hop tables in this document (gmplsHopTable, gmplsCHopTable and
   gmplsARHopTable) and the segment tables in the [LSRMIB]
   (mplsInSegmentTable and mplsOutSegmentTable) contain objects with
   syntax MplsLabel.

Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 5]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   MplsLabel (defined in [TCMIB]) is a 32-bit integer that is capable of
   representing any MPLS label and most GMPLS labels. However, some
   GMPLS labels are larger than 32 bits and may be of arbitrary length.
   Further, some labels that may be safely encoded in 32 bits are
   constructed from multiple sub-fields. Additionally, some GMPLS
   technologies support the concatenation of individual labels to
   represent a data flow carried as multiple sub-flows.

   These GMPLS cases require that something other than a simple 32-bit
   integer is made available to represent the labels. This is achieved
   through the gmplsLabelTable contained in [GMPLSLSRMIB].

   The tables in this document and [LSRMIB] that include objects with
   syntax MplsLabel also include companion objects that are row
   pointers. If the row pointer is set to zeroDotZero (0.0) then object
   of syntax MplsLabel contains the label encoded as a 32-bit integer.
   But otherwise the row pointer indicates a row in another MIB table
   that includes the label. In these cases, the row pointer may indicate
   a row in the gmplsLabelTable.

   This provides both a good way to support legacy systems that
   implement the previous version of this MIB [TEMIB], and a significant
   simplification in GMPLS systems that are limited to a single, simple
   label type.

   Note that gmplsLabelTable supports concatenated labels through the
   use of a label sub-index (gmplsLabelSubindex).

7. Example of GMPLS Tunnel Setup

   This section contains an example of which MIB objects should be
   modified to create a GMPLS tunnel.  This example shows a best effort,
   loosely routed, bidirectional traffic engineered tunnel, which spans
   two hops of a simple network, uses Generalized Label requests with
   Lambda encoding, has label recording and shared link layer
   protection.  Note that these objects should be created on the "head-
   end" LSR.

   First in the mplsTunnelTable:
   {
     mplsTunnelIndex                = 1,
     mplsTunnelInstance             = 1,
     mplsTunnelIngressLSRId         = 123.123.125.1,
     mplsTunnelEgressLSRId          = 123.123.126.1,
     mplsTunnelName                 = "My first tunnel",
     mplsTunnelDescr                = "Here to there and back again",
     mplsTunnelIsIf                 = true (1),
     mplsTunnelXCPointer            = mplsXCIndex.3.0.0.12,
     mplsTunnelSignallingProto      = none (1),
     mplsTunnelSetupPrio            = 0,
     mplsTunnelHoldingPrio          = 0,
     mplsTunnelSessionAttributes    = recordRoute (4),
     mplsTunnelOwner                = snmp (2),
     mplsTunnelLocalProtectInUse    = false (0),
     mplsTunnelResourcePointer      = mplsTunnelResourceIndex.6,
     mplsTunnelInstancePriority     = 1,
     mplsTunnelHopTableIndex        = 1,

Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 6]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

     mplsTunnelPrimaryInstance      = 0,
     mplsTunnelIncludeAnyAffinity   = 0,
     mplsTunnelIncludeAllAffinity   = 0,
     mplsTunnelExcludeAnyAffinity   = 0,
     mplsTunnelPathInUse            = 1,
     mplsTunnelRole                 = head(1),
     mplsTunnelRowStatus            = createAndWait (5),
   }

   In gmplsTunnelTable(1,1,123.123.125.1,123.123.126.1):
   {
     gmplsTunnelUnnumIf             = true (1),
     gmplsTunnelAttributes          = labelRecordingRequired (1),
     gmplsTunnelLSPEncoding         = tunnelLspLambda (8),
     gmplsTunnelSwitchingType       = lsc (150),
     gmplsTunnelLinkProtection      = shared (2),
     gmplsTunnelGPid                = lambda (37),
     gmplsTunnelSecondary           = false(0),
     gmplsTunnelDirection           = bidirectional (1)
     gmplsTunnelPathComp            = explicit(2),
     gmplsTunnelUpNotRecip          = 0x7B7B7D01,
     gmplsTunnelDownNotRecip        = 0x00000000,
     gmplsTunnelAdminStatusFlags    = 0,
     gmplsTunnelExtraParamsPtr      = 0.0
   }

   Entries in the mplsTunnelResourceTable, mplsTunnelHopTable and
   gmplsTunnelHopTable are created and activated at this time.

   In mplsTunnelResourceTable:
   {
     mplsTunnelResourceIndex        = 6,
     mplsTunnelResourceMaxRate      = 0,
     mplsTunnelResourceMeanRate     = 0,
     mplsTunnelResourceMaxBurstSize = 0,
     mplsTunnelResourceRowStatus    = createAndGo (4)
   }

   The next two instances of mplsTunnelHopEntry are used to denote the
   hops this tunnel will take across the network.

   The following denotes the beginning of the network, or the first hop.
   We have used the fictitious LSR identified by "123.123.125.1" as our
   example head-end router.

   In mplsTunnelHopTable:
   {
     mplsTunnelHopListIndex         = 1,
     mplsTunnelPathOptionIndex      = 1,
     mplsTunnelHopIndex             = 1,
     mplsTunnelHopAddrType          = ipV4 (1),
     mplsTunnelHopIpv4Addr          = 123.123.125.1,
     mplsTunnelHopIpv4PrefixLen     = 9,
     mplsTunnelHopType              = strict (1),
     mplsTunnelHopRowStatus         = createAndWait (5),
   }


Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 7]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   The following denotes the end of the network, or the last hop in our
   example. We have used the fictitious LSR identified by
   "123.123.126.1" as our end router.

   In mplsTunnelHopTable:
   {
     mplsTunnelHopListIndex         = 1,
     mplsTunnelPathOptionIndex      = 1,
     mplsTunnelHopIndex             = 2,
     mplsTunnelHopAddrType          = ipV4 (1),
     mplsTunnelHopIpv4Addr          = 123.123.126.1,
     mplsTunnelHopIpv4PrefixLen     = 9,
     mplsTunnelHopType              = loose (2),
     mplsTunnelHopRowStatus         = createAndGo (4)
   }

   Now an associated entry in the gmplsTunnelHopTable is created to
   provide additional GMPLS hop configuration indicating that the first
   hop is an unnumbered link using explicit forward and reverse labels.
   An entry in the gmplsLabelTable is created first to include the
   explicit label.

   In gmplsLabelTable:
   {
     gmplsLabelInterface            = 2,
     gmplsLabelIndex                = 1,
     gmplsLabelSubindex             = 0,
     gmplsLabelType                 = =
gmplsFreeformGeneralizedLabel(3),
     gmplsLabelFreeform             = 0xFEDCBA9876543210
     gmplsLabelRowStatus            = createAndGo(4)
   }

   In gmplsTunnelHopTable(1,1,1):
   {
     gmplsTunnelHopLabelStatuses    = forwardPresent(0)
                                                +reversePresent(1),
     gmplsTunnelHopExpLabelPtr      = gmplsLabelTable (2, 1, 0)
     gmplsTunnelHopExpRvrsLabelPtr  = gmplsLabelTable (2, 1, 0)
   }

   The first hop is now activated:

   In mplsTunnelHopTable(1,1,1):
   {
     mplsTunnelHopRowStatus         = active (1)
   }

   No gmplsTunnelHopEntry is created for the second hop as it contains
   no special GMPLS features.

   Finally the mplsTunnelEntry is activated:

   In mplsTunnelTable(1,1,123.123.125.1,123.123.126.1)
   {
     mplsTunnelRowStatus            = active(1)
   }


Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 8]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

8. GMPLS Traffic Engineering MIB Definitions

   GMPLS-TE-STD-MIB DEFINITIONS ::= BEGIN

   IMPORTS
     MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
     Integer32, Unsigned32, Counter32,
     Counter64, IpAddress, zeroDotZero
       FROM SNMPv2-SMI
     MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
       FROM SNMPv2-CONF
     TruthValue, TimeStamp, DisplayString, RowPointer
       FROM SNMPv2-TC
     InetAddress
       FROM INET-ADDRESS-MIB
     mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId,
     mplsTunnelEgressLSRId, mplsTunnelHopListIndex,
     mplsTunnelHopPathOptionIndex, mplsTunnelHopIndex,
     mplsTunnelARHopListIndex, mplsTunnelARHopIndex,
     mplsTunnelCHopListIndex, mplsTunnelCHopIndex,
     mplsTunnelEntry, mplsTunnelSignallingProto,
     mplsTunnelAdminStatus, mplsTunnelOperStatus
       FROM MPLS-TE-STD-MIB
     gmplsStdMIB
       FROM GMPLS-TC-STD-MIB
   ;

   gmplsTeStdMIB MODULE-IDENTITY
         LAST-UPDATED
           "200406010900Z" -- 1 June 2004 9:00:00 GMT
         ORGANIZATION
           "Common Control And Management Protocols (CCAMP)
            Working Group"
         CONTACT-INFO
           "       Thomas D. Nadeau
                   Cisco Systems, Inc.
            Email: tnadeau@cisco.com

                   Cheenu Srinivasan
                   Bloomberg L.P.
            Email: cheenu@bloomberg.net

                   Adrian Farrel
                   Old Dog Consulting
            Email: adrian@olddog.co.uk

                   Ed Harrison
                   Data Connection Ltd.
            Email: ed.harrison@dataconnection.com

                   Tim Hall
                   Data Connection Ltd.
            Email: tim.hall@dataconnection.com

            Comments about this document should be emailed direct to the
            CCAMP working group mailing list at ccamp@ops.ietf.org"


Nadeau, Srinivasan, Farrel, Hall and Harrison                   [Page 9]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

         DESCRIPTION
           "This MIB module contains managed object definitions
            for GMPLS Traffic Engineering (TE).

            Copyright (C) The Internet Society (2004).  This
            version of this MIB module is part of RFCXXX; see
            the RFC itself for full legal notices."

   -- Revision history.
         REVISION
           "200406010900Z" -- 1 June 2004 09:00:00 GMT
         DESCRIPTION
           "Initial revision, published as part of RFC XXXX."
   ::= { gmplsStdMIB xx }

   -- Top level components of this MIB.

   -- Notifications
   gmplsTeNotifications OBJECT IDENTIFIER ::= { gmplsTeStdMIB 0 }

   -- tables, scalars
   gmplsTeScalars OBJECT IDENTIFIER ::= { gmplsTeStdMIB 1 }
   gmplsTeObjects OBJECT IDENTIFIER ::= { gmplsTeStdMIB 2 }

   -- conformance
   gmplsTeConformance OBJECT IDENTIFIER ::= { gmplsTeStdMIB 3 }


   -- GMPLS Tunnel scalars.

   gmplsTunnelsConfigured OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The number of GMPLS tunnels configured on this
        device. A GMPLS tunnel is considered configured if
        an entry for the tunnel exists in the
        gmplsTunnelTable and the associated
        mplsTunnelRowStatusis active(1)."
   ::= { gmplsTeScalars 1 }


   gmplsTunnelsActive OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The number of GMPLS tunnels active on this device.
        A GMPLS tunnel is considered active if there is an
        entry in the gmplsTunnelTable and the associated
        mplsTunnelOperStatus for the tunnel is up(1)."
   ::= { gmplsTeScalars 2 }

   -- End of GMPLS Tunnel scalars.



Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 10]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   -- GMPLS tunnel table.

   gmplsTunnelTable OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "The gmplsTunnelTable 'extends' the mplsTunnelTable.
        It allows GMPLS tunnels to be created between an LSR
        and a remote endpoint, and existing tunnels to be
        reconfigured or removed.
        Note that only point-to-point tunnel segments are
        supported, although multi-point-to-point and point-
        to-multi-point connections are supported by an LSR
        acting as a cross-connect. Each tunnel can thus have
        one out-segment originating at this LSR and/or one
        in-segment terminating at this LSR.

        The row status of an entry in this table is
        controlled by mplsTunnelRowStatus in the
        corresponding entry in mplsTunnelTable. That is,
        it is not permitted to create a row in this table,
        nor to modify an existing row, when the
        corresponding mplsTunnelRowStatus has value
        active(1).

        The exception to this rule is the gmplsTunnelAdminStatusFlags
        object, which can be modified whilst the tunnel is active."
   ::= { gmplsTeObjects 1 }

   gmplsTunnelEntry OBJECT-TYPE
     SYNTAX  GmplsTunnelEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "An entry in this table in association with the
        corresponding entry in the mplsTunnelTable
        represents a GMPLS tunnel.
        An entry can be created by a network administrator
        or by an SNMP agent as instructed by a signaling
        protocol."
     INDEX {
       mplsTunnelIndex,
       mplsTunnelInstance,
       mplsTunnelIngressLSRId,
       mplsTunnelEgressLSRId
     }
   ::= { gmplsTunnelTable 1 }

   GmplsTunnelEntry ::= SEQUENCE {
     gmplsTunnelUnnumIf            TruthValue,
     gmplsTunnelAttributes         BITS,
     gmplsTunnelLSPEncoding        Integer32,
     gmplsTunnelSwitchingType      Integer32,
     gmplsTunnelLinkProtection     BITS,
     gmplsTunnelGPid               Integer32,
     gmplsTunnelSecondary          TruthValue,

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 11]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

     gmplsTunnelDirection          INTEGER,
     gmplsTunnelPathComp           INTEGER,
     gmplsTunnelUpNotRecip         IpAddress,
     gmplsTunnelDownNotRecip       IpAddress,
     gmplsTunnelAdminStatusFlags   BITS,
     gmplsTunnelExtraParamsPtr     RowPointer
   }

   gmplsTunnelUnnumIf OBJECT-TYPE
     SYNTAX  TruthValue
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Denotes whether or not this tunnel corresponds to an
        unnumbered interface represented in the interfaces
        group table.
        This object is only used if mplsTunnelIsIf is set to
        'true'.
        If both this object and the mplsTunnelIsIf object
        are set to 'true', the originating LSR adds an
        LSP_TUNNEL_INTERFACE_ID object to the outgoing Path
        message.
        This object contains information that is only used
        by the terminating LSR."
     REFERENCE
       "Signalling Unnumbered Links in RSVP-TE, Kompella, K.
           and Rekhter, Y., RFC 3477, January 2003."
     DEFVAL  { false }
   ::= { gmplsTunnelEntry 1 }

   gmplsTunnelAttributes OBJECT-TYPE
     SYNTAX BITS {
       labelRecordingDesired (0)
     }
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "This bitmask indicates optional parameters for this
        tunnel. These bits should be taken in addition to
        those defined in mplsTunnelSessionAttributes in
        order to determine the full set of options to be
        signaled (for example SESSION_ATTRIBUTES flags in
        RSVP-TE).
        The following describes these bitfields:

        labelRecordingDesired
          This flag indicates that label information should be
          included when doing a route record.  This bit is not
          valid unless the recordRoute bit is set."

     REFERENCE
       "1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
           Awduche et al, RFC 3209, December 2001."
     DEFVAL  { { } }
   ::= { gmplsTunnelEntry 2 }



Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 12]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelLSPEncoding OBJECT-TYPE
     SYNTAX  Integer32 (0..255)
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "This object indicates the encoding of the LSP being
        requested.
        A value of zero indicates that GMPLS signaling is
        not in use. Some objects in this MIB module may be
        of use for MPLS signaling extensions that do not use
        GMPLS signaling. By setting this object to zero, an
        application may indicate that only those objects
        meaningful in MPLS should be examined.
        The values to use are currently defined in
        Generalized Multi-Protocol Label Switching (GMPLS)
        Signaling Functional Description, RFC 3471. Further
        values may be defined in future RFCs.
          tunnelLspPacket (1),
          tunnelLspEthernet (2),
          tunnelLspAnsiEtsiPdh (3),
          -- the value 4 is deprecated
          tunnelLspSdhSonet (5),
          -- the value 6 is deprecated
          tunnelLspDigitalWrapper (7),
          tunnelLspLambda (8),
          tunnelLspFiber (9),
          -- the value 10 is deprecated
          tunnelLspFiberChannel (11),
          tunnelDigitalPath (12),
          tunnelOpticalChannel (13)"
     REFERENCE
       "1. Berger, L., et al., Generalized Multi-Protocol
           Label Switching (GMPLS) Signaling Functional
           Description, RFC 3471, January 2003.
        2. D. Papadimitriou (Editor), Generalized MPLS
           Signalling Extensions for G.709 Optical Transport
           Networks Control"
     DEFVAL  { 0 }
   ::= { gmplsTunnelEntry 3 }

   gmplsTunnelSwitchingType OBJECT-TYPE
     SYNTAX  Integer32 (0..255)
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Indicates the type of switching that should be performed on
        a particular link. This field is needed for links that
        advertise more than one type of switching capability. Values
        of this object are as the Switching Capability field defined
        in Internet Draft OSPF Extensions in Support of Generalized
        MPLS. Further values may be defined in future RFCs.
          unknown (0),
          psc1 (1),
          psc2 (2),
          psc3 (3),
          psc4 (4),
          l2sc (51),

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 13]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

          tdm (100),
          lsc (150),
          fsc (200)
        This object is only meaningful if
        gmplsTunnelLSPEncoding is not set to 0."
     REFERENCE
       "1. Kompella, K., et al., OSPF Extensions in Support
           of Generalized MPLS, draft-ietf-ccamp-ospf-gmpls-
           extensions-12.txt, October 2003, work in progress.
        2. Berger, L., et al., Generalized Multi-Protocol
           Label Switching (GMPLS) Signaling Functional
           Description, RFC 3471, January 2003."
     DEFVAL  { 0 }
   ::= { gmplsTunnelEntry 4 }

   gmplsTunnelLinkProtection OBJECT-TYPE
     SYNTAX  BITS {
       extraTraffic(0),
       unprotected(1),
       shared (2),
       dedicatedOneToOne (3),
       dedicatedOnePlusOne(4),
       enhanced(5)
     }
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "This bitmask indicates the level of link protection
        required. A value of zero (no bits set) indicates
        that any protection may be used.
        The following describes these bitfields:

        extraTraffic
          Indicates that the LSP should use links that are
          protecting other (primary) traffic.  Such LSPs may
          be preempted when the links carrying the (primary)
          traffic being protected fail.

        unprotected
          Indicates that the LSP should not use any link layer
          protection.

        shared
          Indicates that a shared link layer protection scheme,
          such as 1:N protection, should be used to support the LSP.

        dedicatedOneToOne
          Indicates that a dedicated link layer protection scheme,
          i.e., 1:1 protection, should be used to support the LSP.

        dedicatedOnePlusOne
          Indicates that a dedicated link layer protection scheme,
          i.e., 1+1 protection, should be used to support the LSP.

        enhanced
          Indicates that a protection scheme that is more reliable than
          Dedicated 1+1 should be used, e.g., 4 fiber BLSR/MS-SPRING.

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 14]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

        This object is only meaningful if
        gmplsTunnelLSPEncoding is not set to 0."
     DEFVAL  { { } }
   ::= { gmplsTunnelEntry 5 }

   gmplsTunnelGPid OBJECT-TYPE
     SYNTAX  Integer32 (0..65535)
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "This object indicates the payload carried by the
        LSP. It is only required when GMPLS will be used for
        this LSP.

        The values to use are currently defined in
        Generalized Multi-Protocol Label Switching (GMPLS)
        Signaling Functional Description, RFC 3471. Further
        values may be defined in future RFCs.

          unknown(0),
          asynchE4(5),
          asynchDS3T3(6),
          asynchE3(7),
          bitsynchE3(8),
          bytesynchE3(9),
          asynchDS2T2(10),
          bitsynchDS2T2(11),
          asynchE1(13),
          bytesynchE1(14),
          bytesynch31ByDS0(15),
          asynchDS1T1(16),
          bitsynchDS1T1(17),
          bytesynchDS1T1(18),
          VC11VC12(19),
          ds1SFAsynch(22),
          ds1ESFAsynch(23),
          ds3M23Asynch(24),
          ds3CBitParityAsynch(25),
          vtLovc(26),
          stsSpeHovc(27),
          posNoScramble16BitCrc(28),
          posNoScramble32BitCrc(29),
          posScramble16BitCrc(30),
          posScramble32BitCrc(31),
          atm(32)
          ethernet(33),
          sdhSonet(34),
          digitalwrapper(36),
          lambda(37),
          ansiEtsiPdh (38),
          lapsSdh (40),
          fddi (41),
          dqdb (42),
          fiberChannel3 (43),
          hdlc (44),
          ethernetV2DixOnly (45),
          ethernet802dot3Only (46),

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 15]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

          g709ODUj (47),
          g709OTUk (48),
          g709CBRorCBRa (49),
          g709CBRb (50),
          g709BSOT (51),
          g709BSNT (52),
          gfpIPorPPP (53),
          gfpEthernetMAC (54),
          gfpEthernetPHY (55),
          g709ESCON (56),
          g709FICON (57),
          g709FiberChannel (58)

        This object is only meaningful if
        gmplsTunnelLSPEncoding is not set to 0."
     REFERENCE
       "1. Berger, L., et al., Generalized Multi-Protocol
           Label Switching (GMPLS) Signaling Functional
           Description, RFC 3471, January 2003."
     DEFVAL  { 0 }
   ::= { gmplsTunnelEntry 6 }

   gmplsTunnelSecondary OBJECT-TYPE
     SYNTAX  TruthValue
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Indicates that the requested LSP is a secondary LSP.

        This object is only meaningful if
        gmplsTunnelLSPEncoding is not set to 0."
     DEFVAL  { false }
   ::= { gmplsTunnelEntry 7 }

   gmplsTunnelDirection OBJECT-TYPE
     SYNTAX  INTEGER {
       forward (0),
       bidirectional (1)
     }
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Whether this tunnel carries forward data (is
        unidirectional) or is bidirectional.
        Values of this object other than 'forward' are meaningful
        only if gmplsTunnelLSPEncoding is not set to 0."
     DEFVAL { forward }
   ::= { gmplsTunnelEntry 8 }

   gmplsTunnelPathComp OBJECT-TYPE
     SYNTAX  INTEGER {
       dynamicFull(1),-- CSPF fully computed
       explicit(2),-- fully specified path
       dynamicPartial(3) -- CSPF partially computed
     }
     MAX-ACCESS read-create
     STATUS current

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 16]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

     DESCRIPTION
       "This value instructs the source node on how to perform
        path computation on the explicit route specified by the
        associated entries in the gmplsTunnelHopTable.

        dynamicFull
          The user specifies at least the source and
          destination of the path and expects that the CSPF
          will calculate the remainder of the path.
        explicit
          The user specifies the entire path for the tunnel to
          take. This path may contain strict or loose hops.
          Evaluation of the explicit route will be performed
          hop by hop through the network.
        dynamicPartial
          The user specifies at least the source and
          destination of the path and expects that the CSPF
          will calculate the remainder of the path. The path
          computed by CSPF is allowed to be only partially
          computed allowing the remainder of the path to be
          filled in across the network.

        This object deprecates gmplsTunnelHopEntryPathComp."
     DEFVAL { dynamicFull }
   ::= { gmplsTunnelEntry 9 }

   gmplsTunnelUpNotRecip OBJECT-TYPE
     SYNTAX  IpAddress
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Indicates the address of the upstream recipient for Notify
        messages relating to this tunnel.

        This object is only valid when signaling a tunnel using
        RSVP.  It is also not valid at the tail end of the tunnel.

        If set to 0, no Notify Request object will be included in
        outgoing Path messages."

     DEFVAL { '00000000'H } -- 0.0.0.0
   ::= { gmplsTunnelEntry 10 }

   gmplsTunnelDownNotRecip OBJECT-TYPE
     SYNTAX  IpAddress
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "Indicates the address of the upstream recipient for Notify
        messages relating to this tunnel.

        This object is only valid when signaling a tunnel using
        RSVP.  It is also not valid at the head end of the tunnel.

        If set to 0, no Notify Request object will be included in
        outgoing Resv messages."


Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 17]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

     DEFVAL { '00000000'H } -- 0.0.0.0
   ::= { gmplsTunnelEntry 11 }

   gmplsTunnelAdminStatusFlags OBJECT-TYPE
      SYNTAX      BITS {
             delInProgress (0),
             adminDown (1),
             testing (2),
             reflect (31)
             }
      MAX-ACCESS   read-create
      STATUS       current
      DESCRIPTION
        "Determines the setting of the Admin Status flags in the
         Admin Status object or TLV, as described in
         RFC 3471.  Setting this field to a non-zero value will
         result in the inclusion of the admin status object on
         signaling messages.

         This value of this object can be modified when the
         corresponding mplsTunnelRowStatus and mplsTunnelAdminStatus
         is active(1).  By doing so, a new signaling message will be
         triggered including the requested Admin Status object or
         TLV."

      ::= { gmplsTunnelEntry 12 }

   gmplsTunnelExtraParamsPtr  OBJECT-TYPE
      SYNTAX       RowPointer
      MAX-ACCESS   read-create
      STATUS       current
      DESCRIPTION
        "Some Tunnels will run over transports that can
         usefully support technology-specific additional parameters
         (for example, SONET resource usage).
         Such can be supplied from an external table and referenced from
         here.
         A value of zeroDotzero in this attribute indicates that there
         is no such additional information."

      DEFVAL      { zeroDotZero }
      ::= { gmplsTunnelEntry 13 }

   -- End of gmplsTunnelTable


   -- Begin gmplsTunnelHopTable

   gmplsTunnelHopTable  OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "The gmplsTunnelHopTable 'extends' the
        mplsTunnelHopTable. It is used to indicate the
        explicit labels to be used in an explicit path for a
        GMPLS tunnel defined in mplsTunnelTable and

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 18]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

        gmplsTunnelTable, when it is established using
        signaling. It does not insert new hops, but does
        define new values for hops defined in
        mplsTunnelHopTable.

        Each row in this table is indexed by the same
        indexes as mplsTunnelHopTable. It is acceptable for
        some rows in mplsTunnelHopTable to have
        corresponding entries in this table and some to have
        no corresponding entry in this table.

        The storage type for an entry in this table is
        inherited from mplsTunnelHopStorageType in the
        corresponding entry in mplsTunnelHopTable.

        The row status of an entry in this table is
        controlled by mplsTunnelHopRowStatus in the
        corresponding entry in mplsTunnelHopTable. That is,
        it is not permitted to create a row in this table,
        nor to modify an existing row, when the
        corresponding mplsTunnelHopRowStatus has value
        active(1)."
   ::= { gmplsTeObjects 2 }

   gmplsTunnelHopEntry  OBJECT-TYPE
     SYNTAX  GmplsTunnelHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "An entry in this table represents additions to a
        tunnel hop defined in mplsTunnelHopEntry. At an
        ingress to a tunnel an entry in this table is
        created by a network administrator for an ERLSP to
        be set up by a signaling protocol. At transit and
        egress nodes an entry in this table may be used to
        represent the explicit path instructions received
        using the signaling protocol."

     INDEX {
       mplsTunnelHopListIndex,
       mplsTunnelHopPathOptionIndex,
       mplsTunnelHopIndex
     }
   ::= { gmplsTunnelHopTable 1 }

   GmplsTunnelHopEntry ::= SEQUENCE {
     gmplsTunnelHopLabelStatuses     BITS,
     gmplsTunnelHopExpLabel          Unsigned32,
     gmplsTunnelHopExpLabelPtr       RowPointer,
     gmplsTunnelHopExpRvrsLabel      Unsigned32,
     gmplsTunnelHopExpRvrsLabelPtr   RowPointer
   }






Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 19]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelHopLabelStatuses OBJECT-TYPE
     SYNTAX  BITS {
       forwardPresent (0),
       reversePresent (1)
     }
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "This bitmask indicates the presence of labels
        indicated by the gmplsTunnelHopExpLabel or
        gmplsTunnelHopExpLabelPtr and
        gmplsTunnelHopExpRvrsLabel or gmplsTunnelHopExpRvrsLabel
        objects.

        For the Present bits, a set bit indicates that a
        label is present for this hop in the route. This
        allows zero to be a valid label value."
   ::= { gmplsTunnelHopEntry 1 }

   gmplsTunnelHopExpLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "If gmplsTunnelHopLabelStatuses object indicates that a
        forward label is present and gmplsTunnelHopExpLabelPtr
        contains the value zeroDotZero, then the label to use on this
        hop is found in this object encoded within a 32-bit integer."
   ::= { gmplsTunnelHopEntry 2 }

   gmplsTunnelHopExpLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelHopLabelStatuses object indicates
        that a forward label is present, this object contains
        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label to use on
        this hop in the forward direction.
        If the gmplsTunnelHopLabelStatuses object indicates that
        a forward label is present and this object contains the
        value zeroDotZero, then the label to use on this hop is
        found in the gmplsTunnelHopExpLabel object."
     DEFVAL  { zeroDotZero }
   ::= { gmplsTunnelHopEntry 3 }

   gmplsTunnelHopExpRvrsLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelHopLabelStatuses object indicates that a
        reverse label is present and gmplsTunnelHopExpRvrsLabelPtr
        contains the value zeroDotZero, then the label to use on
        this hop is found in this object encoded as a 32-bit integer."
   ::= { gmplsTunnelHopEntry 4 }

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 20]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelHopExpRvrsLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-create
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelHopLabelStatuses object indicates
        that a reverse label is present, this object contains
        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label to use on
        this hop in the reverse direction.
        If the gmplsTunnelHopLabelStatuses object indicates that
        a reverse label is present and this object contains the
        value zeroDotZero, then the label to use on this hop is
        found in the gmplsTunnelHopExpRvrsLabel object."
     DEFVAL  { zeroDotZero }
   ::= { gmplsTunnelHopEntry 5 }

   -- End of gmplsTunnelHopTable

   -- Tunnel Actual Route Hop table.

   gmplsTunnelARHopTable  OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelARHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "The gmplsTunnelARHopTable 'extends' the
        mplsTunnelARHopTable. It is used to indicate the
        labels currently in use for a GMPLS tunnel defined
        in mplsTunnelTable and gmplsTunnelTable, as reported
        by the signaling protocol. It does not insert new
        hops, but does define new values for hops defined in
        mplsTunnelARHopTable.

        Each row in this table is indexed by the same indexes as
        mplsTunnelARHopTable. It is acceptable for some rows in
        mplsTunnelARHopTable to have corresponding entries in this
        table and some to have no corresponding entry in this table.

        Note that since the information necessary to build
        entries within this table is not provided by some
        signaling protocols and might not be returned in all
        cases of other signaling protocols, implementation
        of this table and mplsTunnelARHopTable is optional.
        Furthermore, since the information in this table is
        actually provided by the signaling protocol after
        the path has been set-up, the entries in this table
        are provided only for observation, and hence, all
        variables in this table are accessible exclusively
        as read-only."
   ::= { gmplsTeObjects 3 }

   gmplsTunnelARHopEntry  OBJECT-TYPE
     SYNTAX  GmplsTunnelARHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 21]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

       "An entry in this table represents additions to a
        tunnel hop visible in mplsTunnelARHopEntry. An entry
        is created by the signaling protocol for a signaled
        ERLSP set up by the signaling protocol.

        At any node on the LSP (ingress, transit or egress)
        Thus at this table and mplsTunnelARHopTable (if the
        tables are supported and if the signaling protocol
        is recording actual route information) contains the
        actual route of the whole tunnel. If the signaling
        protocol is not recording the actual route, this
        table MAY report the information from the
        gmplsTunnelHopTable or the gmplsTunnelCHopTable.

        Note that the recording of actual labels is distinct
        from the recording of the actual route in some
        signaling protocols. This feature is enabled using
        the gmplsTunnelAttributes object."
     INDEX {
       mplsTunnelARHopListIndex,
       mplsTunnelARHopIndex
     }
   ::= { gmplsTunnelARHopTable 1 }

   GmplsTunnelARHopEntry ::= SEQUENCE {
     gmplsTunnelARHopLabelStatuses     BITS,
     gmplsTunnelARHopExpLabel          Unsigned32,
     gmplsTunnelARHopExpLabelPtr       RowPointer,
     gmplsTunnelARHopExpRvrsLabel      Unsigned32,
     gmplsTunnelARHopExpRvrsLabelPtr   RowPointer,
     gmplsTunnelARHopProtection        BITS
   }

   gmplsTunnelARHopLabelStatuses OBJECT-TYPE
     SYNTAX  BITS {
       forwardPresent (0),
       reversePresent (1),
       forwardGlobal (2),
       reverseGlobal (3)
     }
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "This bitmask indicates the presence and status of
        labels indicated by the
        gmplsTunnelARHopExpLabel or gmplsTunnelARHopExpLabelPtr and
        gmplsTunnelARHopExpRvrsLabel or gmplsTunnelARHopExpRvrsLabelPtr
        objects.
        For the Present bits, a set bit indicates that a label
        is present for this hop in the route. For the Global bits,
        a set bit indicates that the label comes from the Global
        Label Space. A clear bit indicates that this is a Per-
        Interface label. A Global bit only has meaning if the
        corresponding Present bit is set."
   ::= { gmplsTunnelARHopEntry 1 }



Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 22]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelARHopExpLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelARHopLabelStatuses object indicates
        that a forward label is present and
        gmplsTunnelARHopExpLabelPtr contains the value
        zeroDotZero, then the label in use on this hop is
        found in this object encoded within a 32-bit integer."
   ::= { gmplsTunnelARHopEntry 2 }

   gmplsTunnelARHopExpLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelARHopLabelStatuses object indicates
        that a forward label is present, this object contains
        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label in use on
        this hop in the forward direction.
        If the gmplsTunnelARHopLabelStatuses object indicates that
        a forward label is present and this object contains the
        value zeroDotZero, then the label in use on this hop is
        found in the gmplsTunnelARHopExpLabel object."
   ::= { gmplsTunnelARHopEntry 3 }

   gmplsTunnelARHopExpRvrsLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelARHopLabelStatuses object indicates
        that a reverse label is present and
        gmplsTunnelARHopExpRvrsLabelPtr contains the value
        zeroDotZero, then the label in use on this hop is
        found in this object encoded as a 32-bit integer."
   ::= { gmplsTunnelARHopEntry 4 }

   gmplsTunnelARHopExpRvrsLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelARHopLabelStatuses object indicates
        that a reverse label is present, this object contains
        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label in use on
        this hop in the reverse direction.
        If the gmplsTunnelARHopLabelStatuses object indicates that
        a reverse label is present and this object contains the
        value zeroDotZero, then the label in use on this hop is
        found in the gmplsTunnelARHopExpRvrsLabel object."
   ::= { gmplsTunnelARHopEntry 5 }



Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 23]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelARHopProtection  OBJECT-TYPE
     SYNTAX  BITS {
       localAvailable (0),
       localInUse (1)
     }
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
      "Availability and usage of protection on the reported link.

       localAvailable
          Indicates that the link downstream of this node
          is protected via a local repair mechanism.
       localInUse
          Indicates that a local repair mechanism is in use to
          maintain this tunnel (usually in the face of an outage
          of the link it was previously routed over)."
   ::= { gmplsTunnelARHopEntry 6 }

   -- End of mplsTunnelARHopTable

   -- Tunnel Computed Hop table.

   gmplsTunnelCHopTable  OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelCHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "The gmplsTunnelCHopTable 'extends' the mplsTunnelCHopTable.
        It is used to indicate additional information about the
        hops of a GMPLS tunnel defined in mplsTunnelTable and
        gmplsTunnelTable, as computed by a constraint-based
        routing protocol, based on the mplsTunnelHopTable
        and the gmplsTunnelHopTable.

        Each row in this table is indexed by the same indexes as
        mplsTunnelCHopTable. It is acceptable for some rows in
        mplsTunnelCHopTable to have corresponding entries in this
        table and some to have no corresponding entry in this table.

        Please note that since the information necessary to
        build entries within this table may not be supported
        by some LSRs, implementation of this table is optional.

        Furthermore, since the information in this table is actually
        provided by a path computation component after the path has
        been computed, the entries in this table are provided only
        for observation, and hence, all objects in this table are
        accessible exclusively as read-only."
   ::= { gmplsTeObjects 4 }

   gmplsTunnelCHopEntry  OBJECT-TYPE
     SYNTAX  GmplsTunnelCHopEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "An entry in this table represents additions to a

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 24]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

        computed tunnel hop visible in mplsTunnelCHopEntry.
        An entry is created by a path computation component
        based on the hops specified in the corresponding
        mplsTunnelHopTable and gmplsTunnelHopTable.

        At a transit LSR this table (if the table is
        supported) MAY contain the path computed by path
        computation engine on (or on behalf of) the transit LSR."
     INDEX {
       mplsTunnelCHopListIndex,
       mplsTunnelCHopIndex
     }
   ::= { gmplsTunnelCHopTable 1 }

   GmplsTunnelCHopEntry ::= SEQUENCE {
     gmplsTunnelCHopLabelStatuses     BITS,
     gmplsTunnelCHopExpLabel          Unsigned32,
     gmplsTunnelCHopExpLabelPtr       RowPointer,
     gmplsTunnelCHopExpRvrsLabel      Unsigned32,
     gmplsTunnelCHopExpRvrsLabelPtr   RowPointer
   }

   gmplsTunnelCHopLabelStatuses OBJECT-TYPE
     SYNTAX  BITS {
       forwardPresent (0),
       reversePresent (1)
     }
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "This bitmask indicates the presence of labels indicated by the
        gmplsTunnelCHopExpLabel or gmplsTunnelCHopExpLabelPtr and
        gmplsTunnelCHopExpRvrsLabel or gmplsTunnelCHopExpRvrsLabelPtr
        objects.
        A set bit indicates that a label is present for this hop in
        the route thus allowing zero to be a valid label value."
   ::= { gmplsTunnelCHopEntry 1 }

   gmplsTunnelCHopExpLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelCHopLabelStatuses object indicates
        that a forward label is present and
        gmplsTunnelCHopExpLabelPtr contains the value
        zeroDotZero, then the label to use on this hop is
        found in this object encoded within a 32-bit integer."
   ::= { gmplsTunnelCHopEntry 2 }

   gmplsTunnelCHopExpLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelCHopLabelStatuses object indicates
        that a forward label is present, this object contains

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 25]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label to use on
        this hop in the forward direction.
        If the gmplsTunnelCHopLabelStatuses object indicates that
        a forward label is present and this object contains the
        value zeroDotZero, then the label to use on this hop is
        found in the gmplsTunnelCHopExpLabel object."
   ::= { gmplsTunnelCHopEntry 3 }

   gmplsTunnelCHopExpRvrsLabel OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelCHopLabelStatuses object indicates
        that a reverse label is present and
        gmplsTunnelCHopExpRvrsLabelPtr contains the value
        zeroDotZero, then the label to use on this hop is
        found in this object encoded as a 32-bit integer."
   ::= { gmplsTunnelCHopEntry 4 }

   gmplsTunnelCHopExpRvrsLabelPtr OBJECT-TYPE
     SYNTAX  RowPointer
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "If the gmplsTunnelCHopLabelStatuses object indicates
        that a reverse label is present, this object contains
        a pointer to a row in another MIB table (such as the
        gmplsLabelTable) that contains the label to use on
        this hop in the reverse direction.
        If the gmplsTunnelCHopLabelStatuses object indicates that
        a reverse label is present and this object contains the
        value zeroDotZero, then the label to use on this hop is
        found in the gmplsTunnelCHopExpRvrsLabel object."
   ::= { gmplsTunnelCHopEntry 5 }

   -- End of gmplsTunnelCHopTable

   -- GMPLS Tunnel Reverse Direction Performance Table.

   gmplsTunnelReversePerfTable  OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelReversePerfEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "This table 'augments' the gmplsTunnelTable to provides
        per-tunnel packet performance information for the
        reverse direction of a bidirectional tunnel. It can be
        seen as supplementing the mplsTunnelPerfTable which
        augments the mplsTunnelTable."
   ::= { gmplsTeObjects 5 }

   gmplsTunnelReversePerfEntry OBJECT-TYPE
     SYNTAX  GmplsTunnelReversePerfEntry
     MAX-ACCESS not-accessible
     STATUS  current

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 26]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

     DESCRIPTION
       "An entry in this table is created by the LSR for every
        bidirectional GMPLS tunnel where packets are visible to
        the LSR."
     AUGMENTS { gmplsTunnelEntry }
   ::= { gmplsTunnelReversePerfTable 1 }

   GmplsTunnelReversePerfEntry ::= SEQUENCE {
     gmplsTunnelReversePerfPackets     Counter32,
     gmplsTunnelReversePerfHCPackets   Counter64,
     gmplsTunnelReversePerfErrors      Counter32,
     gmplsTunnelReversePerfBytes       Counter32,
     gmplsTunnelReversePerfHCBytes     Counter64
   }

   gmplsTunnelReversePerfPackets OBJECT-TYPE
     SYNTAX  Counter32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "Number of packets forwarded on the tunnel in the
        reverse direction if it is bidirectional."
   ::= { gmplsTunnelReversePerfEntry 1 }

   gmplsTunnelReversePerfHCPackets OBJECT-TYPE
     SYNTAX  Counter64
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "High capacity counter for number of packets forwarded on
       the tunnel in the reverse direction if it is bidirectional."
   ::= { gmplsTunnelReversePerfEntry 2 }

   gmplsTunnelReversePerfErrors OBJECT-TYPE
     SYNTAX  Counter32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "Number of errored packets received on the tunnel in
        the reverse direction if it is bidirectional."
   ::= { gmplsTunnelReversePerfEntry 3 }

   gmplsTunnelReversePerfBytes OBJECT-TYPE
     SYNTAX  Counter32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 27]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

       "Number of bytes forwarded on the tunnel in the
        reverse direction if it is bidirectional."
   ::= { gmplsTunnelReversePerfEntry 4 }

   gmplsTunnelReversePerfHCBytes OBJECT-TYPE
     SYNTAX  Counter64
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "High capacity counter for number of bytes forwarded
        on the tunnel in the reverse direction if it is
        bidirectional."
   ::= { gmplsTunnelReversePerfEntry 5 }

   -- End of gmplsTunnelReversePerfTable

   -- GMPLS Tunnel Error Table.

   gmplsTunnelErrorTable  OBJECT-TYPE
     SYNTAX  SEQUENCE OF GmplsTunnelErrorEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "This table 'augments' the mplsTunnelTable

        This table provides per-tunnel information about
        errors. Errors may be detected locally or reported
        through the signaling protocol.

        Error reporting is not exclusive to GMPLS and this
        table may be applied in MPLS systems."
   ::= { gmplsTeObjects 6 }

   gmplsTunnelErrorEntry OBJECT-TYPE
     SYNTAX  GmplsTunnelErrorEntry
     MAX-ACCESS not-accessible
     STATUS  current
     DESCRIPTION
       "An entry in this table is created by the LSR for
        every tunnel where error information is visible to
        the LSR.
        Note that systems which read the objects in this table
        one at a time may experience a discontinuity as the
        result of a new error occurring in between object reads.
        Systems that are vulnerable to this should read
        gmplsTunnelErrorLastTime before and after reading the
        other objects."
     AUGMENTS { mplsTunnelEntry }
   ::= { gmplsTunnelErrorTable 1 }

   GmplsTunnelErrorEntry ::= SEQUENCE {
     gmplsTunnelErrorLastErrorType      INTEGER,
     gmplsTunnelErrorLastTime           TimeStamp,
     gmplsTunnelErrorReporterType       INTEGER,
     gmplsTunnelErrorReporter   InetAddress,
     gmplsTunnelErrorCode               Unsigned32,
     gmplsTunnelErrorSubcode            Unsigned32,
     gmplsTunnelErrorTLVs               OCTET STRING,
     gmplsTunnelErrorHelpString         DisplayString
   }

   gmplsTunnelErrorLastErrorType OBJECT-TYPE
     SYNTAX  INTEGER {
       noError (0),
       unknown (1),
       localProtocol (2),
       remoteProtocol (3),

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 28]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

       configuration (4),
       pathComputation (5),
       localResources (6)
     }
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The nature of the last error. Provides
        interpretation context for
        gmplsTunnelErrorProtocolCode and
        gmplsTunnelErrorProtocolSubcode. A value of noError
        (0) shows that there is no error associated with
        this tunnel and means that the other objects in this
        entry have no meaning."
   ::= { gmplsTunnelErrorEntry 1 }

   gmplsTunnelErrorLastTime OBJECT-TYPE
     SYNTAX  TimeStamp
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The time at which the last error occurred. This is
        presented as the value of SysUpTime when the error
        occurred or was reported to this node.
        If gmplsTunnelErrorLastErrorType has the value
        noError (0), then this object is ignored."
   ::= { gmplsTunnelErrorEntry 2 }

   gmplsTunnelErrorReporterType OBJECT-TYPE
      SYNTAX  INTEGER {
        unknown (0),
        localNode (1),
        localIpV4 (2),
        remoteIpV4 (3),
        localIpV6 (4),
        remoteIpV6 (5)
      }
      MAX-ACCESS read-only
      STATUS  current
      DESCRIPTION
        "The reporter of the last error recorded.
         This object is used principally to aid in interpretation
         of gmplsTunnelErrorReporterIpv4Addr and
         gmplsTunnelErrorReporterIpv6Addr. Where the error has
         been locally generated and there is no requirement to
         associate the error with any specific local address (such
         as an interface), the value localNode (2) may be used.
         If gmplsTunnelErrorLastError has the value noError
         (0), then this object is ignored."
   ::= { gmplsTunnelErrorEntry 3 }

   gmplsTunnelErrorReporter OBJECT-TYPE
     SYNTAX  InetAddress
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION


Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 29]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

       "The address of the node reporting the last error, or
        the address of the resource (such as an interface)
        associated with the error.
        If gmplsTunnelErrorLastErrorType has the value
        noError (0), then this object is ignored.
        This object should be interpreted in the context of
        the value of the object gmplsTunnelErrorReporterType.
        If that object has value localIpV4 (2) or remoteIpV4 (3),
        this object should be viewed as having a syntax of
        InetAddressIPv4. If gmplsTunnelErrorReporterType has
        value localIpV6 (3) or remoteIpV6 (5), this object should be
        viewed as having a syntax of InetAddressIPv6. Otherwise the
        object should contain the value zero and should be ignored."
     REFERENCE
       "RFC3291, Textual Conventions for Internet Network
        Addresses, Section 4. Usage Hints."
   ::= { gmplsTunnelErrorEntry 4 }

   gmplsTunnelErrorCode OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The primary error code associated with the last
        error.

        The interpretation of this error code depends on the
        value of gmplsTunnelErrorLastErrorType. If the value
        of gmplsTunnelErrorLastErrorType is noError (0) the
        value of this object should be 0 and should be
        ignored. If the value of
        gmplsTunnelErrorLastErrorType is localProtocol (2)
        or remoteProtocol (3) the error should be
        interpreted in the context of the signling protocol
        identified by the mplsTunnelSignallingProto object.

        Values in excess 32767 of are not used by signaling
        protocols and may safely be used as implementation-
        specific error codes. "
   ::= { gmplsTunnelErrorEntry 5 }

   gmplsTunnelErrorSubcode OBJECT-TYPE
     SYNTAX  Unsigned32
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The secondary error code associated with the last
        error and the protocol used to signal this tunnel.
        This value is interprettd in the context of the
        value of gmplsTunnelErrorCode.
        If the value of gmplsTunnelErrorLastErrorType is
        noError (0) the value of this object should be 0 and
        should be ignored."
   ::= { gmplsTunnelErrorEntry 6 }




Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 30]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelErrorTLVs OBJECT-TYPE
     SYNTAX  OCTET STRING
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "The sequence of interface identifier TLVs reported
        with the error by the protocol code. The interpretation
        of the TLVs and the encoding within the protocol are
        described in the references.
        A value of zero in the first octet indicates that no
        TLVs are present."
      REFERENCE
       "RFC3471, Generalized Multi-Protocol Label Switching
        (GMPLS) Signaling Functional Description,
        Section 9.1. Interface Identification.
        RFC3473, Generalized Multi-Protocol Label Switching
        (GMPLS) Signaling Resource ReserVation Protocol-Traffic
        Engineering (RSVP-TE) Extensions, Section 8.2. Errored
        Interface Identification"
   ::= { gmplsTunnelErrorEntry 7 }

   gmplsTunnelErrorHelpString OBJECT-TYPE
     SYNTAX  DisplayString
     MAX-ACCESS read-only
     STATUS  current
     DESCRIPTION
       "A textual string containing information about the
        last error, recovery actions and support advice. If
        there is no help string this object contains a zero
        length string.
        If the value of gmplsTunnelErrorLastErrorType is
        noError (0) this object should contain a zero length
        string, but may contain a help string indicating
        that there is no error."
   ::= { gmplsTunnelErrorEntry 8 }

   -- GMPLS Notifications.

   gmplsTunnelDown NOTIFICATION-TYPE
   OBJECTS  {
     mplsTunnelAdminStatus,
     mplsTunnelOperStatus,
     gmplsTunnelErrorLastErrorType,
     gmplsTunnelErrorReporterType,
     gmplsTunnelErrorReporter,
     gmplsTunnelErrorCode,
     gmplsTunnelErrorSubcode
   }
   STATUS      current
   DESCRIPTION
        "This notification is generated when a
         mplsTunnelOperStatus object for one of the
         configured tunnels is about to enter the down state
         from some other state (but not from the notPresent
         state). This other state is indicated by the
         included value of mplsTunnelOperStatus.
         The objects in this notification provide additional

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 31]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

         error information that indicates the reason why the
         tunnel has transitioned down.
         Note that an implementation SHOULD only issue one of
         mplsTunnelDown and gmplsTunnelDown for a single event
         on a single tunnel."
   ::= { gmplsTeNotifications 1 }

   -- End of notifications.

   -- Module compliance.

   gmplsTeGroups
     OBJECT IDENTIFIER ::= { gmplsTeConformance 1 }

   gmplsTeCompliances
     OBJECT IDENTIFIER ::= { gmplsTeConformance 2 }

   gmplsTeModuleCompliance MODULE-COMPLIANCE
     STATUS current
     DESCRIPTION
       "Compliance statement for agents that support the
        GMPLS TE MIB."
     MODULE -- this module

   -- The mandatory group has to be implemented by all
   -- LSRs that originate/terminate ESLSPs/tunnels.
   -- In addition, depending on the type of tunnels
   -- supported, other groups become mandatory as
   -- explained below.

   MANDATORY-GROUPS {
     gmplsTunnelGroup,
     gmplsTunnelScalarGroup
   }

-- GROUP gmplsTunnelManualGroup
--   DESCRIPTION
--     "This group is mandatory for devices which support
--      manual configuration of tunnels, in addition to
--      gmplsTunnelGroup.  The following constraints apply:
--      mplsTunnelSignallingProto should be at least read-
--      only with a value of none(1)."

   GROUP gmplsTunnelSignaledGroup
     DESCRIPTION
       "This group is mandatory for devices which support
        signaled tunnel set up, in addition to
        gmplsTunnelGroup.  The following constraints apply:

        mplsTunnelSignallingProto should be at least read-
        only returning a value of ldp(2), or rsvp(3)."

   GROUP gmplsTunnelIsNotIntfcGroup
     DESCRIPTION
       "This group is mandatory for devices which support
        tunnels that are not interfaces, in addition to
        gmplsTunnelGroup.  The following constraints apply:

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 32]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

        gmplsTunnelIsIf must at least be read-only returning no(0)."

   GROUP gmplsTunnelIsIntfcGroup
     DESCRIPTION
       "This group is mandatory for devices which support
        tunnels that are interfaces, in addition to
        gmplsTunnelGroup."

   GROUP gmplsTunnelOptionalGroup
     DESCRIPTION
       "Objects in this group are optional."

   GROUP gmplsTeNotificationGroup
   DESCRIPTION "This group is mandatory for those implementations
                which can implement the notifications contained
                in this group."

   -- GMPLS Tunnel scalars.
   -- All scalars have max access read-only

   -- gmplsTunnelTable

   OBJECT gmplsTunnelAttributes
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelLSPEncoding
     SYNTAX Integer32
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelSwitchingType
     SYNTAX Integer32
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelLinkProtection
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelGPid
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelSecondary
     SYNTAX TruthValue
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."




Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 33]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   OBJECT gmplsTunnelDirection
     SYNTAX INTEGER {
       forward (0),
       bidirectional (1)
     }
     MIN-ACCESS  read-only
     DESCRIPTION
       "Only forward (0) is required."

   OBJECT gmplsTunnelPathComp
     SYNTAX INTEGER {
       dynamicFull(1),   -- CSPF fully computed
       explicit(2),      -- fully
       dynamicPartial(3) -- CSPF partially computed
     }

     MIN-ACCESS  read-only
     DESCRIPTION
       "Only explicit (2) is required."

   OBJECT gmplsTunnelUpNotRecip
     SYNTAX  IpAddress
     MIN-ACCESS read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelDownNotRecip
     SYNTAX  IpAddress
     MIN-ACCESS read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelAdminStatusFlags
      SYNTAX      BITS {
             delInProgress (0),
             adminDown (1),
             testing (2),
             reflect (31)
             }
      MIN-ACCESS   read-only
      DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelExtraParamsPtr
     SYNTAX  RowPointer
     MIN-ACCESS read-only
     DESCRIPTION
       "Write access is not required."

   -- gmplsTunnelHopTable

   -- gmplsTunnelHopLabelStatuses has max access read-only

   OBJECT gmplsTunnelHopExpLabel
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 34]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   OBJECT gmplsTunnelHopExpLabelPtr
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelHopExpRvrsLabel
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   OBJECT gmplsTunnelHopExpRvrsLabelPtr
     MIN-ACCESS  read-only
     DESCRIPTION
       "Write access is not required."

   -- gmplsTunnelARHopTable
   -- all objects have max access read-only

   -- glmpsTunnelCHopTable
   -- all objects have max access read-only

   -- gmplsTunnelReversePerfTable
   -- all objects have max access read-only

   -- gmplsTunnelErrorTable
   -- all objects have max access read-only
   ::= { gmplsTeCompliances 1 }

   -- Units of conformance.

   gmplsTunnelGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelDirection,
       gmplsTunnelReversePerfPackets,
       gmplsTunnelReversePerfHCPackets,
       gmplsTunnelReversePerfErrors,
       gmplsTunnelReversePerfBytes,
       gmplsTunnelReversePerfHCBytes,
       gmplsTunnelErrorLastErrorType,
       gmplsTunnelErrorLastTime,
       gmplsTunnelErrorReporterType,
       gmplsTunnelErrorReporter,
       gmplsTunnelErrorCode,
       gmplsTunnelErrorSubcode,
       gmplsTunnelErrorTLVs,
       gmplsTunnelErrorHelpString
     }
     STATUS  current
     DESCRIPTION
       "Necessary, but not sufficient, set of objects to implement
        tunnels.  In addition, depending on the type of the tunnels
        supported (for example, manually configured or signaled,
        persistent or non-persistent, etc.), the following other
        groups defined below are mandatory: gmplsTunnelManualGroup
        and/or gmplsTunnelSignaledGroup, gmplsTunnelIsNotIntfcGroup
        and/or gmplsTunnelIsIntfcGroup."
   ::= { gmplsTeGroups 1 }

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 35]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

-- gmplsTunnelManualGroup  OBJECT-GROUP
--   OBJECTS {
--     mplsTunnelSignallingProto
--   }
--   STATUS  current
--   DESCRIPTION
--     "Object(s) needed to implement manually configured
--      tunnels."
-- ::= { gmplsTeGroups 2 }

   gmplsTunnelSignaledGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelAttributes,
       gmplsTunnelLSPEncoding,
       gmplsTunnelSwitchingType,
       gmplsTunnelLinkProtection,
       gmplsTunnelGPid,
       gmplsTunnelSecondary,
       gmplsTunnelPathComp,
       gmplsTunnelUpNotRecip,
       gmplsTunnelDownNotRecip,
       gmplsTunnelAdminStatusFlags,
       gmplsTunnelHopLabelStatuses,
       gmplsTunnelHopExpLabel,
       gmplsTunnelHopExpLabelPtr,
       gmplsTunnelHopExpRvrsLabel,
       gmplsTunnelHopExpRvrsLabelPtr
     }

     STATUS  current
     DESCRIPTION
       "Objects needed to implement signaled tunnels."
   ::= { gmplsTeGroups 3 }

   gmplsTunnelScalarGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelsConfigured,
       gmplsTunnelsActive
     }
     STATUS  current
     DESCRIPTION
       "Scalar objects needed to implement MPLS tunnels."
   ::= { gmplsTeGroups 4 }

   gmplsTunnelIsIntfcGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelUnnumIf
     }
     STATUS  current
     DESCRIPTION
       "Objects needed to implement tunnels that are
        interfaces."
   ::= { gmplsTeGroups 5 }





Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 36]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   gmplsTunnelIsNotIntfcGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelUnnumIf
     }
     STATUS  current
     DESCRIPTION
       "Objects needed to implement tunnels that are not
        interfaces."
   ::= { gmplsTeGroups 6 }

   gmplsTunnelOptionalGroup OBJECT-GROUP
     OBJECTS {
       gmplsTunnelExtraParamsPtr,
       gmplsTunnelARHopLabelStatuses,
       gmplsTunnelARHopExpLabel,
       gmplsTunnelARHopExpLabelPtr,
       gmplsTunnelARHopExpRvrsLabel,
       gmplsTunnelARHopExpRvrsLabelPtr,
       gmplsTunnelARHopProtection,
       gmplsTunnelCHopLabelStatuses,
       gmplsTunnelCHopExpLabel,
       gmplsTunnelCHopExpLabelPtr,
       gmplsTunnelCHopExpRvrsLabel,
       gmplsTunnelCHopExpRvrsLabelPtr
     }
     STATUS  current
     DESCRIPTION
       "The objects in this group are optional."
   ::= { gmplsTeGroups 7 }

   gmplsTeNotificationGroup NOTIFICATION-GROUP
     NOTIFICATIONS {
        gmplsTunnelDown
     }
     STATUS  current
     DESCRIPTION
       "Set of notifications implemented in this module.
        None is mandatory."
   ::= { gmplsTeGroups 8 }

   END

9. Security Considerations

   It is clear that the MIB modules described in this document in
   association with the MPLS-TE-STD-MIB are potentially useful for
   monitoring of MPLS and GMPLS tunnels. These MIB modules can also be
   used for configuration of certain objects, and anything that can be
   configured can be incorrectly configured, with potentially disastrous
   results.

   There are a number of management objects defined in these MIB modules
   with a MAX-ACCESS clause of read-write and/or read-create. Such
   objects may be considered sensitive or vulnerable in some network
   environments. The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations. These are the tables and objects and their

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 37]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   sensitivity/vulnerability:

   o  the gmplsTunnelTable and gmplsTunnelHopTable collectively contain
      objects to provision GMPLS tunnels interfaces at their ingress
      LSRs. Unauthorized write access to objects in these tables, could
      result in disruption of traffic on the network. This is especially
      true if a tunnel has already been established. The use of stronger
      mechanisms such as SNMPv3 security should be considered where
      possible. Specifically, SNMPv3 VACM and USM MUST be used with any
      SNMPv3 agent which implements these MIB modules.

   Some of the readable objects in these MIB modules "i.e., objects with
   a MAX-ACCESS other than not-accessible" may be considered sensitive
   or vulnerable in some network environments. It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP. These are the tables and objects and their
   sensitivity/vulnerability:

   o  the gmplsTunnelTable, gmplsTunnelHopTable, gmplsTunnelARHopTable,
      gmplsTunnelCHopTable, gmplsTunnelReversePerfTable,
      gmplsTunnelErrorTable collectively show the tunnel network
      topology and status. If an Administrator does not want to reveal
      this information, then these tables should be considered
      sensitive/vulnerable.

   SNMP versions prior to SNMPv3 did not include adequate security. Even
   if the network itself is secure "for example by using IPSec", even
   then, there is no control as to who on the secure network is allowed
   to access and GET/SET "read/change/create/delete" the objects in
   these MIB modules. It is RECOMMENDED that implementers consider the
   security features as provided by the SNMPv3 framework "see [RFC3410],
   section 8", including full support for the SNMPv3 cryptographic
   mechanisms "for authentication and privacy".

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module, is properly configured to give access to
   the objects only to those principals "users" that have legitimate
   rights to indeed GET or SET "change/create/delete" them.

10. Acknowledgments

   This document extends [TEMIB]. The authors would like to express
   their gratitude to all those who worked on that earlier MIB document.
   Thanks also to Tony Zinicola and Jeremy Crossen for their valuable
   contributions during an early implementation, and to Baktha
   Muralidharan for his review.

   Special thanks to Joan Cucchiara and Len Nieman for their help with
   compilation issues.





Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 38]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

11. References

11.1. Normative References

   [RFC2119]        Bradner, S., "Key words for use in RFCs to Indicate
                    Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]        McCloghrie, K., Perkins, D., Schoenwaelder, J.,
                    Case, J., Rose, M., and S. Waldbusser, "Structure
                    of Management Information Version 2 (SMIv2)", STD
                    58, RFC 2578, April 1999.

   [RFC2579]        McCloghrie, K., Perkins, D., Schoenwaelder, J.,
                    Case, J., Rose, M., and S. Waldbusser, "Textual
                    Conventions for SMIv2", STD 58, RFC 2579, April
                    1999.

   [RFC2580]        McCloghrie, K., Perkins, D., Schoenwaelder, J.,
                    Case, J., Rose, M., and S. Waldbusser, "Conformance
                    Statements for SMIv2", STD 58, RFC 2580, April
                    1999.

   [RFC3031]        Rosen, E., Viswanathan, A., and R. Callon,
                    "Multiprotocol Label Switching Architecture", RFC
                    3031, January 2001.

   [RFC3209]        Awduche, D., Berger, L., Gan, D., Li, T.,
                    Srinivasan, V., and G. Swallow, "RSVP-TE:
                    Extensions to RSVP for LSP Tunnels", RFC 3209,
                    December 2001.

   [RFC3212]        Jamoussi, B., Aboul-Magd, O., Andersson, L.,
                    Ashwood-Smith, P., Hellstrand, F., Sundell, K.,
                    Callon, R., Dantu, R., Wu, L., Doolan, P., Worster,
                    T., Feldman, N., Fredette, A., Girish, M., Gray,
                    E., Halpern, J., Heinanen, J., Kilty, T., Malis,
                    A., and P. Vaananen, "Constraint-Based LSP Setup
                    using LDP", RFC 3212, December 2001.

   [RFC3291]        Daniele, M., Haberman, B., Routhier, S.,
                    Schoenwaelder, J., and Braunschweig, TU, "Textual
                    Conventions for Internet Network Addresses",
                    RFC3291, May 2002

   [RFC3471]        Berger, L. (Editor), "Generalized Multi-Protocol
                    Label Switching (GMPLS) Signaling Functional
                    Description", RFC 3471, January 2003.

   [RFC3472]        Ashwood-Smith, P., Berger, L. (Editors),
                    "Generalized MPLS Signaling - CR-LDP Extensions",
                    RFC 3472, January 2003.

   [RFC3473]        Berger, L. (Editor), "Generalized MPLS Signaling -
                    RSVP-TE Extensions", RFC 3473, January 2003.

   [RFC3477]        Kompella, K. and Rekhter, Y., "Signalling Unnumbered
                    Links in RSVP-TE", RFC 3477, January 2003.

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 39]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   [RFC3480]        Kompella, K., Rekhter, Y. and Kullberg, A.,
                    "Signalling Unnumbered Links in CR-LDP", RFC 3480,
                    February 2003.

   [GMPLSArch]      Mannie, E. (Editor), "Generalized Multiprotocol
                    Label Switching (GMPLS) Architecture",
                    draft-many-gmpls-architecture-07.txt, May
                    2003, work in progress.

   [GMPLSLSRMIB]    Nadeau, T., Srinivasan, C., A., Farrel, A., Hall,
                    T., and Harrison, E., "Generalized Multiprotocol
                    Label Switching (GMPLS) Label Switching Router
                    (LSR) Management Information Base", draft-ietf-
                    ccamp-gmpls-lsr-mib-05.txt, June 2004, work in
                    progress.

   [GMPLSOSPF]      Kompella, K., et al., "OSPF Extensions in Support
                    of Generalized MPLS", draft-ietf-ccamp-ospf-gmpls-
                    extensions-12.txt, October 2003, work in progress.

   [GMPLSTCMIB]     Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
                    and Harrison, E., "Definitions of Textual
                    Conventions for Multiprotocol Label Switching
                    (MPLS) Management", draft-ietf-ccamp-gmpls-te-mib-
                    05.txt, June 2004, work in progress.

   [LSRMIB]         Srinivasan, C., Viswanathan, A. and T. Nadeau,
                    "Multiprotocol Label Switching (MPLS) Label
                    Switching Router (LSR) Management Information
                    Base", draft-ietf-mpls-lsr-mib-14.txt, November
                    2003, work in progress.

   [TCMIB]          Nadeau, T., Cucchiara, J. (Editors) "Definitions of
                    Textual Conventions for Multiprotocol Label
                    Switching (MPLS) Management",
                    draft-ietf-mpls-tc-mib-10.txt, November 2003, work
                    in progress.

   [TEMIB]          Nadeau, T., Srinivasan, C, Viswanathan, A.,
                    "Multiprotocol Label Switching (MPLS) Traffic
                    Engineering Management Information Base",
                    draft-ietf-mpls-te-mib-14.txt, November 2003,
                    work in progress.

11.2. Informational References

   [RFC2026]        S. Bradner, "The Internet Standards Process --
                    Revision 3", RFC 2026, October 1996.

   [RFC3413]        Levi, D., Meyer, P., Stewart, B., "SNMP
                    Applications", RFC 3413, December 2002.

   [RFC3410]        Case, J., Mundy, R., Partain, D. and B. Stewart,
                    "Introduction and Applicability Statements for
                    Internet-Standard Management Framework", RFC 3410,
                    December 2002.


Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 40]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   [RFC3411]        Harrington, D., Presuhn, R., and B. Wijnen, "An
                    Architecture for Describing Simple Network
                    Management Protocol (SNMP) Management Frameworks",
                    RFC 3411, December 2002.

   [GMPLS-G709]     D. Papadimitriou (Editor), "Generalized MPLS
                    Signalling Extensions for G.709 Optical Transport
                    Networks Control", draft-ietf-ccamp-gmpls-g709-
                    06.txt, January 2004, work in progress.

12. Authors' Addresses

   Thomas D. Nadeau
   Cisco Systems, Inc.
   300 Apollo Drive
   Chelmsford, MA 01824
   Phone: +1-978-244-3051
   Email: tnadeau@cisco.com

   Cheenu Srinivasan
   Bloomberg L.P.
   499 Park Ave.,
   New York, NY 10022
   Phone: +1-212-893-3682
   Email: cheenu@bloomberg.net

   Adrian Farrel
   Old Dog Consulting
   Phone: +44-(0)-1978-860944
   Email: adrian@olddog.co.uk

   Tim Hall
   Data Connection Ltd.
   100 Church Street
   Enfield, Middlesex
   EN2 6BQ, UK
   Phone: +44 20 8366 1177
   Email: tim.hall@dataconnection.com

   Ed Harrison
   Data Connection Ltd.
   100 Church Street
   Enfield, Middlesex
   EN2 6BQ, UK
   Phone: +44 20 8366 1177
   Email: ed.harrison@dataconnection.com

13. Intellectual Property Considerations

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights. Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 41]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard. Please address the information to the IETF at
   ietf-ipr@ietf.org.

13.1. IPR Disclosure Acknowledgement

   By submitting this Internet-Draft, I certify that any applicable
   patent or other IPR claims of which I am aware have been disclosed,
   and any of which I become aware will be disclosed, in accordance with
   RFC 3668.

14. Full Copyright Statement

   Copyright (C) The Internet Society (2004). This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

15. Changes and Pending Work

   This section to be removed before the draft progresses to RFC.

15.1. Pending Work

   The following work items have been identified for this draft.  They
   will be addressed in a future version.

   - Expand conformance statements to give one for monitoring only,
     and one for monitoring and control.
   - Resolve conformance statement from gmplsTunnelManualGroup.

15.1. Changes from version 4 to version 5

   - New IPR and copyright boiler plate.
   - Correct typo in name of gmplsTunnelExtraParamsPtr
   - Add to list of encoding types and GPids for G.709
   - Add G.709 reference





Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 42]


Internet Draft     draft-ietf-ccamp-gmpls-te-mib-05.txt        June 2004

15.2. Changes from version 3 to version 4

   - Provide a way to configure additional tunnel parameters such as
     tunnel resources through an arbitrary row pointer.
   - Update references.
   - Change reporting IP addresses to use InetAddress syntax
   - Add support for IF_ID error reporting.
   - Add a new notification, gmplsTunnelDown, containing cause
     information.
   - Clarify relationship to the gmplsLabelTable.
   - Update descriptive text.
   - Bring usage of labels in line with latest [LSRMIB].

15.3. Changes from version 2 to version 3

   - Work on basic compilation issues.
   - Resolve defaults for objects with syntax BITS.
   - Update references.
   - Clarify which objects can be modified when rowStatus and
     adminStatus are set to active.
   - Control and reporting of upstream and downstream Notify
     Recipients.
   - Add support for control and reporting of GMPLS Administrative
     Status object.
   - Update examples.

































Nadeau, Srinivasan, Farrel, Hall and Harrison                  [Page 43]