Network Working Group                                      G. Bernstein
Internet Draft                                        Grotto Networking
Intended status: Standards Track                                 Y. Lee
Expires: August 2014                                              D. Li
                                                                 Huawei
                                                             W. Imajuku
                                                                    NTT


                                                      February 13, 2014

        Routing and Wavelength Assignment Information Encoding for
                   Wavelength Switched Optical Networks


                  draft-ietf-ccamp-rwa-wson-encode-24.txt


Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with
   the provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

   This Internet-Draft will expire on August 13, 2014.

Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.






Bernstein and Lee      Expires August 13, 2014                 [Page 1]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document.  Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.

Abstract

   A wavelength switched optical network (WSON) requires that certain
   key information elements are made available to facilitate path
   computation and the establishment of label switching paths (LSPs).
   The information model described in "Routing and Wavelength
   Assignment Information for Wavelength Switched Optical Networks"
   shows what information is required at specific points in the WSON.
   Part of the WSON information model contains aspects that may be of
   general applicability to other technologies, while other parts are
   fairly specific to WSONs.

   This document provides efficient, protocol-agnostic encodings for
   the WSON specific information elements. It is intended that
   protocol-specific documents will reference this memo to describe how
   information is carried for specific uses. Such encodings can be used
   to extend GMPLS signaling and routing protocols. In addition these
   encodings could be used by other mechanisms to convey this same
   information to a path computation element (PCE).



Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC-2119 [RFC2119].

Table of Contents


   1. Introduction...................................................3
   1.1. Terminology..................................................4
   2. Resources, Resource Blocks, and the Resource Pool..............4
      2.1. Resource Block Set Field..................................5
   3. Resource Accessibility/Availability............................6



Bernstein and Lee      Expires August 13, 2014                 [Page 2]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      3.1. Resource Accessibility Field..............................6
      3.2. Resource Wavelength Constraints Field.....................8
      3.3. Resource Block Pool State (RBPoolState) Field............10
      3.4. Resource Block Shared Access Wavelength Availability
      (RBSharedAccessWaveAvailability) Field........................11
   4. Resource Block Information (ResourceBlockInfo) Field..........13
      4.1. Optical Interface Class List Subfield....................15
            4.1.1. ITU-G.698.1 Application Code Mapping.............16
            4.1.2. ITU-G.698.2 Application Code Mapping.............18
            4.1.3. ITU-G.959.1 Application Code Mapping.............19
            4.1.4. ITU-G.695 Application Code Mapping...............22
      4.2. Acceptable Client Signal List Subfield...................24
      4.3. Input Bit Rate List Subfield.............................24
      4.4. Processing Capability List Subfield......................25
   5. Security Considerations.......................................26
   6. IANA Considerations...........................................27
      6.1. Types for subfields of WSON Resource Block Information...27
   7. Acknowledgments...............................................27
   APPENDIX A: Encoding Examples....................................28
      A.1. Wavelength Converter Accessibility Field.................28
      A.2. Wavelength Conversion Range Field........................29
      A.3. An OEO Switch with DWDM Optics...........................30
   8. References....................................................33
      8.1. Normative References.....................................33
      8.2. Informative References...................................33
   9. Contributors..................................................35
   Authors' Addresses...............................................36
   Intellectual Property Statement..................................37
   Disclaimer of Validity...........................................38

1. Introduction

   A Wavelength Switched Optical Network (WSON) is a Wavelength
   Division Multiplexing (WDM) optical network in which switching is
   performed selectively based on the center wavelength of an optical
   signal.

   [RFC6163] describes a framework for Generalized Multiprotocol Label
   Switching (GMPLS) and Path Computation Element (PCE) control of a
   WSON. Based on this framework, [RWA-Info] describes an information
   model that specifies what information is needed at various points in
   a WSON in order to compute paths and establish Label Switched Paths
   (LSPs).

   This document provides efficient encodings of information needed by
   the routing and wavelength assignment (RWA) process in a WSON. Such



Bernstein and Lee      Expires August 13, 2014                 [Page 3]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   encodings can be used to extend GMPLS signaling and routing
   protocols. In addition these encodings could be used by other
   mechanisms to convey this same information to a path computation
   element (PCE). Note that since these encodings are relatively
   efficient they can provide more accurate analysis of the control
   plane communications/processing load for WSONs looking to utilize a
   GMPLS control plane.



1.1. Terminology

   Refer to [RFC6163] for CWDM, DWDM, RWA, WDM.

   Refer to Section 5 of [Gen-Encode] for the terminology of Resources,
   Resources Blocks, and Resource Pool.



2. Resources, Resource Blocks, and the Resource Pool

   This section provides encodings for the information elements defined
   in [RWA-Info] that have applicability to WSON.  The encodings are
   designed to be suitable for use in the GMPLS routing protocols OSPF
   [RFC4203] and IS-IS [RFC5307] and in the PCE protocol (PCEP)
   [RFC5440]. Note that the information distributed in [RFC4203] and
   [RFC5307] is arranged via the nesting of sub-TLVs within TLVs and
   this document defines elements to be used within such constructs.
   Specific constructs of sub-TLVs and the nesting of sub-TLVs of the
   information element defined by this document will be defined in the
   respective protocol enhancement documents.

   This document defines the following information elements pertaining
   to resources within an optical node:

     . Resource Accessibility <ResourceAccessibility>

     . Resource Wavelength Constraints <ResourceWaveConstraints>

     . Resource Block Pool State <RBPoolState>

     . Resource Block Shared Access Wavelength Availability
        <RBSharedAccessWaveAvailability>

     . Resource Block Information <ResourceBlockInfo>




Bernstein and Lee      Expires August 13, 2014                 [Page 4]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   Each of these information elements works with one or more sets of
   resources rather than just a single resource block. This motivates
   the following field definition.



2.1. Resource Block Set Field

   In a WSON node that includes resource blocks (RB), denoting subsets
   of these blocks allows one to efficiently describe common properties
   of the blocks and to describe the structure and characteristics, if
   non-trivial, of the resource pool. The RB Set field is defined in a
   similar manner to the label set concept of [RFC3471].

   The information carried in a RB set field is defined by:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    Action     |C|  Reserved   |        Length                 |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        RB Identifier 1                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      :                               :                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        RB Identifier n                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


      Action: 8 bits

         0 - Inclusive List

   Indicates that the TLV contains one or more RB elements that are
   included in the list.

         1 - Inclusive Range(s)

   Indicates that the TLV contains one or more ranges of RBs.  Each
   individual range is denoted by two 32 bit RB identifier. The first
   32 bits is the RB identifier for the start of the range and the next
   32 bits is the RB identifier for the end of the range. Note that the
   Length field is used to determine the number of ranges.

      C (Connectivity bit): Set to 0 to denote fixed (possibly multi-
   cast) connectivity; Set to 1 to denote potential (switched)



Bernstein and Lee      Expires August 13, 2014                 [Page 5]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   connectivity. Used in Resource Accessibility field. Ignored
   elsewhere.

         Reserved: 7 bits

   This field is reserved. It MUST be set to zero on transmission and
   MUST be ignored on receipt.

      Length: 16 bits

   The total length of this field in bytes.

      RB Identifier:

   The RB identifier represents the ID of the resource block which is a
   32 bit integer.

   Usage Note: the inclusive range "Action" can result in very compact
   encoding of resource sets and it can be advantages to number
   resource blocks in such a way so that status updates (dynamic
   information) can take advantage of this efficiency.

3. Resource Accessibility/Availability

   This section defines the information elements for dealing with
   accessibility and availability of resource blocks within a pool of
   resources. These include the ResourceAccessibility,
   ResourceWaveConstraints, and RBPoolState fields.



3.1. Resource Accessibility Field

   This information element describes the structure of the resource
   pool in relation to the switching device. In particular it indicates
   the ability of an input port to reach sets of resources and of sets
   of resources to reach a particular output port. This is the
   PoolInputMatrix and PoolOutputMatrix of [RWA-Info].

   The Resource Accessibility is defined by:









Bernstein and Lee      Expires August 13, 2014                 [Page 6]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |Reserved(8bits)|C|             Reserved (23 bits)              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Input Link Set Field A #1                  |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          RB Set Field A #1                    |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         Additional Link set and RB set pairs as needed to     |
      :                    specify PoolInputMatrix                    :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                Output Link Set Field B #1                     |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             RB Set B Field #1 (for output connectivity)       |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         Additional Link Set and RB set pairs as needed to     |
      :                    specify PoolOutputMatrix                   :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where


   C (Connectivity bit): Connectivity indicates how the input/output
   ports connect to the resource blocks.

         0 -- the device is fixed (e.g., a connected port must go
         through the resource block)

         1 -- the device is switched (e.g., a port can be configured to
         go through a resource but isn't required)

   The For the Input and Output Link Set Fields, the Link Set Field
   encoding defined in [Gen-Encode] is to be used. A Label Set Field
   MUST carry a label as defined in [RFC6205].










Bernstein and Lee      Expires August 13, 2014                 [Page 7]


Internet-Draft   Wavelength Switched Optical Networks     February 2014




   Note that the direction parameter within the Link Set Field is used
   to indicate whether the link set is an input or output link set, and
   the bidirectional value for this parameter is not permitted in this
   field.

   See Appendix A.1 for an illustration of this encoding.


3.2. Resource Wavelength Constraints Field

   Resources, such as wavelength converters, etc., may have a limited
   input or output wavelength ranges. Additionally, due to the
   structure of the optical system not all wavelengths can necessarily
   reach or leave all the resources. These properties are described by
   using one or more resource wavelength restrictions fields as defined
   below:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |I|O|B|                      Reserved                           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                Input Wavelength Constraints                   |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                Output Wavelength Constraints                  |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   I = 1 or 0 indicates the presence or absence of the Input Wavelength
   Constraints Field.

   O = 1 or 0 indicates the presence or absence of the Output
   Wavelength Constraints Field.

   B = 1 indicates that a single wavelength constraints field
   represents both Input and Output Wavelength Constraints Fields.

   Currently the only valid combinations of (I,O,B) are (1,0,0),
   (0,1,0), (1,1,0), (0,0,1).



Bernstein and Lee      Expires August 13, 2014                 [Page 8]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      RB Set Field:

   A set of resource blocks (RBs) which have the same wavelength
   restrictions.

      Input Wavelength Constraints Field:

   Indicates the wavelength input restrictions of the RBs in the
   corresponding RB set. This field is encoded via the Label Set field
   of [Gen-Encode].

      Output Wavelength Constraints Field:

   Indicates the wavelength output restrictions of RBs in the
   corresponding RB set. This field is encoded via the Label Set field
   of [Gen-Encode].

































Bernstein and Lee      Expires August 13, 2014                 [Page 9]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


3.3. Resource Block Pool State (RBPoolState) Field

   The state of the pool is given by the number of resources available
   with particular characteristics. A resource block set is used to
   encode all or a subset of the resources of interest. The usage state
   of resources within a resource block set is encoded as either a list
   of 16 bit integer values or a bit map indicating whether a single
   resource is available or in use. The bit map encoding is appropriate
   when resource blocks consist of a single resource. This information
   can be relatively dynamic, i.e., can change when a connection (LSP
   is established or torn down.

      0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Action        |    Reserved                                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                  RB Usage state                               |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where Action = 0 denotes a list of 16 bit integers and Action = 1
   denotes a bit map. In both cases the elements of the RB Set field
   are in a one-to-one correspondence with the values in the usage RB
   usage state area.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Action = 0    |    Reserved                                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                  RB#1 state   |      RB#2 state               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                 RB#n-1 state  |   RB#n state or Padding       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   RB#i State (16 bits, unsigned integer): indicates Resource Block #i
   is in use or available.



Bernstein and Lee      Expires August 13, 2014                [Page 10]


Internet-Draft   Wavelength Switched Optical Networks     February 2014



   Whether the last 16 bits is a wavelength converter (RB) state or
   padding is determined by the number of elements in the RB set field.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Action = 1    |    Reserved                                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                  RB Usage state bitmap                        |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     ......             |      Padding bits    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   RB Usage state:  Variable Length but must be a multiple of 4 byes.

   Each bit indicates the usage status of one RB with 0 indicating the
   RB is available and 1 indicating the RB is in used. The sequence of
   the bit map is ordered according to the RB Set field with this
   element.

   Padding bits: Variable Length

3.4. Resource Block Shared Access Wavelength Availability
   (RBSharedAccessWaveAvailability) Field

   Resources blocks may be accessed via a shared fiber. If this is the
   case, then wavelength availability on these shared fibers is needed
   to understand resource availability.















Bernstein and Lee      Expires August 13, 2014                [Page 11]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |I|O|                          Reserved                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |            Input Available Wavelength Set Field               |
      :                          (Optional)                           :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             Output Available Wavelength Set Field             |
      :                          (Optional)                           :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


      I bit:

   Indicates whether the input available wavelength set field is
   included (1) or not (0).

      O bit:

   Indicates whether the output available wavelength set field is
   included (1) or not (0).

      RB Set Field:

   A Resource Block set in which all the members share the same input
   or output fiber or both.

      Input Available Wavelength Set Field:

   Indicates the wavelengths currently available (not being used) on
   the input fiber to this resource block. This field is encoded via
   the Label Set field of [Gen-Encode].

      Output Available Wavelength Set Field:

   Indicates the wavelengths currently available (not being used) on
   the output fiber from this resource block. This field is encoded via
   the Label Set field of [Gen-Encode].







Bernstein and Lee      Expires August 13, 2014                [Page 12]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


4. Resource Block Information (ResourceBlockInfo) Field

   As defined in [RWA-INFO], the Resource Block Information
   <ResourceBlockInfo> field is used to represent resource signal
   constraints and processing capabilities of a node.


   The fundamental properties of a resource block are:

     (a) Optical Interface Class List(s)
     (b) Acceptable Client Signal (shared input, modulation, FEC, bit
        rate, G-PID)
     (c) Input Bit Rate
     (d) Processing Capabilities (number of resources in a block,
        regeneration, performance monitoring, vendor specific)


   ResourceBlockInfo fields are used to convey relatively static
   information about individual resource blocks including the resource
   block properties and the number of resources in a block.

   When more than one ResourceBlockInfo field is used, there are no
   ordering requirements amongst these fields.

   This ResourceBlockInfo field has the following format:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          RB Set Field                         |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |I|O|                         Reserved                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Optional subfield 1                    |
      :                              ...                              :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      :                               :                               :
      :                               :                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Optional subfield N                    |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+





Bernstein and Lee      Expires August 13, 2014                [Page 13]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   RB Set Field is described in Section 2.1.

   The shared input or output indication is indicated by the first bit
   (I) and the second bit (O):

   where I and O are set to 1 if the resource blocks identified in the
   RB set field utilized a shared fiber for input/output access and set
   to 0 otherwise.

   Zero or more Optional subfields MAY be present. Optional subfields
   have following format:


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Type             |             Length            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            Value...                           |
      .                                                               .
      .                                                               .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   The Length field defines the length of the value portion in bytes
   (thus a subfield with no value portion would have a length of zero).
   The subfield is padded to four-byte alignment; padding is not
   included in the Length field (so a three byte value would have a
   length of three, but the total size of the subfield would be eight
   byte).  Unrecognized types are not processed. If multiple subfields
   of the same type are present, only the first of the type SHOULD be
   processed.

   The following subfield Types are defined:

      Value          Length      Sub-TLV Type

       1             variable    Optical Interface Class List
       2             variable    Acceptable Client Signal List
       3             variable    Input Bit Rate List
       4             variable    Processing Capability List

     See the IANA Considerations section for allocation of new Types.



Bernstein and Lee      Expires August 13, 2014                [Page 14]


Internet-Draft   Wavelength Switched Optical Networks     February 2014





4.1. Optical Interface Class List Subfield

   The list of Optical Interface Class subfield has the following
   format:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           Reserved                        |I|O|
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Optical Interface Classes                   |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   The following I and E combination are defined:

   I   O

   0   0   Invalid

   1   0   Optical Interface Class List acceptable in input

   0   1   Optical Interface Class List available in output

   1   1   Optical Interface Class List available on both input and
   output.

   The Resource Block MAY contain one or more lists according to
   input/output flags.

   The Optical Interface Classes Format is defined as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S|     Reserved                |    OI Code Points             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         Optical Interface Class                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         Optical Interface Class  (Cont.)                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Bernstein and Lee      Expires August 13, 2014                [Page 15]


Internet-Draft   Wavelength Switched Optical Networks     February 2014





     Where the first 32 bits of the encoding shall be used to identify
     the semantic of the Optical Interface Class in the following way:



        S  Standard bit.

              S=0, identify not ITU code points

              S=1, identify ITU application codes

        With S=0, the OI Code Points field can take the following
     values:

           0: reserved

           1: Vendor Specific Optical Interface Class.

        With S=1, the OI Code Points field can take the following
     values:

           0: reserved

           1: [ITU-G.698.1] application code.

           2: [ITU-G.698.2] application code.

           3: [ITU-G.959.1] application code.

           4: [ITU-G.695] application code.

   In case of ITU Application Code, the mapping between the string
   defining the application code and the 64 bits number implementing
   the optical interface class is given in the following sections.



   4.1.1. ITU-G.698.1 Application Code Mapping

      Recommendation ITU-G.698.1 defines the Application Codes: DScW-
   ytz(v) and B-DScW-ytz(v).  Where:

      B: means Bidirectionals.



Bernstein and Lee      Expires August 13, 2014                [Page 16]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      D: means a DWDM application.

      S: take values N (narrow spectral excursion), W (wide spectral
   excursion).

      c: Channel Spacing (GHz).

      W: take values S (short-haul), L (long-haul).

      y: take values 1 (NRZ 2.5G), 2 (indicating NRZ 10G).

      t: take only D value is defined (link does not contain optical
   amplifier)

      z: take values 2 (ITU-T G.652 fibre), 3 (ITU-T G.653 fibre), 5
   (indicating ITU-T G.655 fibre).

      v: take values S (Short wavelength), C (Conventional), L (Long
   wavelength).

      An Optional F can be added indicating a FEC Encoding.

   These get mapped into the 64 bit OIC field as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |B|  D  |S|   c   |   W   |   y   |   t   |   z   |  v  |   F   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           reserved                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   Where (values between parenthesis refer to ITU defined values as
   reported above):

         B: = 1 bidirectional, 0 otherwise

         D (prefix): = 0 reserved, = 1 (D)

         S: = 0 (N), = 1 (W)

         c: Channel Spacing, 4 bits mapped according to same definition
   in [RFC6205] (note that DWDM spacing apply here)




Bernstein and Lee      Expires August 13, 2014                [Page 17]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


         W: = 0 reserved, = 2 (S), = 3 (L)

         y: = 0 reserved, = 1 (1), = 2 (2)

         t: = 0 reserved, = 4 (D)

         z: = 0 reserved, = 2 (2), = 3 (3), = 5 (5)

         v: = 0 reserved, = 1 (S), = 2 (C), = 3 (L)

         F (suffix): = 0 reserved, = 1 Fec Encoding

      Values not mentioned here are not allowed in this application
   code, the last 32 bits are reserved and shall be set to zero.



   4.1.2. ITU-G.698.2 Application Code Mapping



   Recommendation ITU-G.698.2 defines the Application Codes: DScW-
   ytz(v) and B-DScW-ytz(v).

      B: means Bidirectional.

      D: means a DWDM application.

      S: take values N (narrow spectral excursion), W (wide spectral
   excursion).

      c: Channel Spacing (GHz).

      W: take values C (link is dispersion compensated), U (link is
   dispersion uncompensated).

      y: take values 1 (NRZ 2.5G), 2 (indicating NRZ 10G).

      t: take value A (link may contains optical amplifier)

      z: take values 2 (ITU-T G.652 fibre), 3 (ITU-T G.653 fibre), 5
   (indicating ITU-T G.655 fibre).

      v: take values S (Short wavelength), C (Conventional), L (Long
   wavelength).




Bernstein and Lee      Expires August 13, 2014                [Page 18]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      An Optional F can be added indicating a FEC Encoding.

       These get mapped into the 64 bit OIC field as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |B|  D  |S|   c   |   W   |   y   |   t   |   z   |  v  |   F   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           reserved                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Where (values between parenthesis refer to ITU defined values as
reported above):

         B: = 1 bidirectional, 0 otherwise

         D (prefix): = 0 reserved, = 1 (D)

         S: = 0 (N), = 1 (W)

         c: Channel Spacing, 4 bits mapped according to same definition
   in [RFC6205] (note that DWDM spacing apply here)

         W: = 0 reserved, = 10 (C), = 11 (U)

         y: = 0 reserved, = 1 (1), = 2 (2)

         t: = 0 reserved, = 1 (A)

         z: = 0 reserved, = 2 (2), = 3 (3), = 5 (5)

         v: = 0 reserved, = 1 (S), = 2 (C), = 3 (L)

         F (suffix): = 0 reserved, = 1 Fec Encoding

      Values not mentioned here are not allowed in this application
   code, the last 32 bits are reserved and shall be set to zero.

   4.1.3. ITU-G.959.1 Application Code Mapping

   Recommendation ITU-G.959.1 defines the Application Codes: PnWx-ytz
   and BnWx-ytz.  Where:





Bernstein and Lee      Expires August 13, 2014                [Page 19]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      P,B: when present indicate Plural or Bidirectional

      n: maximum number of channels supported by the application code
   (i.e. an integer number)

      W: take values I (intra-office), S (short-haul), L (long-haul), V
   (very long-haul), U (ultra long-haul).

      x: maximum number of spans allowed within the application code
   (i.e. an integer number)

      y: take values 1 (NRZ 2.5G), 2 (NRZ 10G), 9 (NRZ 25G), 3 (NRZ
   40G), 7 (RZ 40G).



      t: take values A (power levels suitable for a booster amplifier
   in the originating ONE and power levels suitable for a pre-amplifier
   in the terminating ONE), B (booster amplifier only), C (pre-
   amplifier only), D (no amplifiers).

      z: take values 1 (1310 nm sources on ITU-T G.652 fibre), 2 (1550
   nm sources on ITU-T G.652 fibre), 3 (1550 nm sources on ITU-T
   G.653 fibre), 5 (1550 nm sources on ITU-T G.655 fibre).

      The following list of suffixes can be added to these application
   codes:

      F: FEC encoding.

      D: Adaptive dispersion compensation.

      E: receiver capable of dispersion compensation.

      r: reduced target distance.

      a: power levels appropriate to APD receivers.

      b: power levels appropriate to PIN receivers.

      These values are encoded as follows:








Bernstein and Lee      Expires August 13, 2014                [Page 20]


Internet-Draft   Wavelength Switched Optical Networks     February 2014




      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | p |  P  |       n           |   W   |     x     |   reserved  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |   y   |   t   |   z   |   suffix  |          reserved         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




      Where (values between parenthesis refer to ITU defined values as
   reported above):

         p (prefix) = 0 otherwise, = 1 Bidirectional (B)

         P (optional): = 0 not present, = 2 (P).



         n: maximum number of channels (10 bits, up to 1024 channels)

         W: = 0 reserved, = 1 (I), = 2 (S), = 3 (L), = 4 (V), = 5 (U)

         x: = number of spans (6 bits, up to 64 spans)

         y: = 0 reserved, = 1 (1), = 2 (2), = 3 (3), = 7 (7), = 9 (9)

         t: = 0 reserved, = 1 (A), = 2 (B), = 3 (C), = 4 (D)

         z: = 0 reserved, = 1 (1), = 2 (2), = 3 (3), = 5 (5)



         suffix is an 6 bit, bit map:

       0 1 2 3 4 5
      +-+-+-+-+-+-+
      |F|D|E|r|a|b|
      +-+-+-+-+-+-+
   where a 1 in the appropriate slot indicates that the corresponding
   suffix has been added.





Bernstein and Lee      Expires August 13, 2014                [Page 21]


Internet-Draft   Wavelength Switched Optical Networks     February 2014




   4.1.4. ITU-G.695 Application Code Mapping




   Recommendation [ITU-G.695] defines the Application Codes: CnWx-ytz
   and B-CnWx-ytz and S-CnWx-ytz.

   Where the optional prefixed are:

      B: Bidirectional

      S: a system using a black link approach

   And the rest of the application code is defined as:

      C: CWDM (Coarse WDM) application

      n: maximum number of channels supported by the application code
   (i.e. an integer number)

      W: take values S (short-haul), L (long-haul).

      x: maximum number of spans allowed

      y: take values 0 (NRZ 1.25G), 1 (NRZ 2.5G), 2 (NRZ 10G).

      t: take values D (link does not contain any optical amplifier).

      z: take values 1 (1310 nm region for ITU-T G.652 fibre), 2 (ITU-T
   G.652 fibre), 3 (ITU-T G.653 fibre), 5 (ITU-T G.655 fibre).

      The following list of suffixes can be added to these application
   codes:

      F: FEC encoding.

      Since the application codes are very similar to the one from the
   G.959 section most of the fields are reused. The 64 bit OIC field is
   encoded as follows:







Bernstein and Lee      Expires August 13, 2014                [Page 22]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | p |  C  |       n           |   W   |     x     |   reserved  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |   y   |   t   |   z   |   suffix  |          reserved         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




      Where (values between parenthesis refer to ITU defined values as
   reported above):

         p: = 0 no prefix, 1 = B bidirectional, = 2 S black link

         C: = 0 reserved, = 3 (C).



         n: maximum number of channels (10 bits, up to 1024 channels)

         W: = 0 reserved, = 1 reserved, = 2 (S), = 3 (L), > 3 reserved

         x: = number of spans (6 bits, up to 64 spans)

         y: = 0 (0), = 1 (1), =2 (2), > 2 reserved

         t: = 4 (D), all other values are reserved

         z: = 0 reserved, = 1 (1), = 2 (2), = 3 (3)

         suffix is an 6 bit, bit map:

       0 1 2 3 4 5
      +-+-+-+-+-+-+
      |F|0|0|0|0|0|
      +-+-+-+-+-+-+
   where a 1 in the appropriate slot indicates that the corresponding
   suffix has been added.









Bernstein and Lee      Expires August 13, 2014                [Page 23]


Internet-Draft   Wavelength Switched Optical Networks     February 2014




4.2. Acceptable Client Signal List Subfield

   This subfield contains a list of acceptable input client signal
   types.

   The acceptable client signal list is a list of Generalized Protocol
   Identifiers (G-PIDs).

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            Reserved           |       Number of G-PIDs        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            G-PID #1           |          G-PID #2             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     :                               |                               :
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            G-PID #N           |                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   Type (16 bits):  identifies the Acceptable Client Signal List field.

   Length (16 bits): The Length field defines the length of the value
   portion in octets.

   The number of G-PIDs is an integer greater than or equal to one.

   G-PIDs are assigned by IANA and many are defined in [RFC3471] and
   [RFC4328].



4.3. Input Bit Rate List Subfield

   This subfield contains a list of bit rate of each input client
   signal types specified in the Input Client Signal List.

   The number of Input Bit Rate MUST match the number of G-PID.








Bernstein and Lee      Expires August 13, 2014                [Page 24]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   Input Bit Rate of G-PID #1                  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     :                                                               :
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   Input Bit Rate of G-PID #N                  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Input Bit Rates are in IEEE floating point format [IEEE].



4.4. Processing Capability List Subfield

   This subfield contains a list of resource processing capabilities.

   The processing capability list field is a list of capabilities that
   can be achieved through the referred resources:

     1. Regeneration capability

     2. Fault and performance monitoring

     3. Vendor Specific capability

   Note that the code points for Fault and performance monitoring and
   vendor specific capability are subject to further study.

   The processing capability list field is then given by:



      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            Reserved           |        Processing Cap ID      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |   Possible additional capability parameters depending upon    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     :   the processing ID                                           :
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+






Bernstein and Lee      Expires August 13, 2014                [Page 25]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   When the processing Cap ID is "regeneration capability", the
   following additional capability parameters are provided in the
   following field:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  T  | C |                 Reserved                            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   Where T bit indicates the type of regenerator:

      T=0: Reserved

      T=1: 1R Regenerator

      T=2: 2R Regenerator

      T=3: 3R Regenerator

   Where C bit indicates the capability of regenerator:

      C=0: Reserved

      C=1: Fixed Regeneration Point

      C=2: Selective Regeneration Point

   Note that when the capability of regenerator is indicated to be
   Selective Regeneration Pools, regeneration pool properties such as
   input and output restrictions and availability need to be specified.
   The code point for this is subject to further study.



5. Security Considerations

   This document defines protocol-independent encodings for WSON
   information and does not introduce any security issues.

   However, other documents that make use of these encodings within
   protocol extensions need to consider the issues and risks associated
   with, inspection, interception, modification, or spoofing of any of
   this information. It is expected that any such documents will
   describe the necessary security measures to provide adequate



Bernstein and Lee      Expires August 13, 2014                [Page 26]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   protection. A general discussion on security in GMPLS networks can
   be found in [RFC5920].



6. IANA Considerations

   IANA allocation requests for protocol dependent encodings will be
   addressed in protocol specific documents based on the encodings
   defined here.

   This document introduces a new registry for GMPLS routing parameters
   for WSON encoding. This new IANA registry will be created to make
   the assignment of a new type and new values for the new "GMPLS
   Routing Parameters for WSON."



6.1. Types for subfields of WSON Resource Block Information

   Under this new GMPLS Routing Parameters for WSON, a new IANA
   registry will be created for nested subfields of the Resource Block
   Information field to create a new section named "Types for subfields
   of WSON Resource Block Information" and allocate new values as
   follows:

   Value          Length      Sub-TLV Type                  Reference

   0                          Reserved
   1              variable    Optical Interface Class List [This.I-D]
   2              variable    Acceptable Client
                              Signal List                  [This.I-D]
   3              variable    Input Bit Rate List          [This.I-D]
   4              variable    Processing Capability List   [This.I-D]
   5-65535                    Unassigned

   Types are to be assigned via Standards Action as defined in
   [RFC5226].



7. Acknowledgments

   This document was prepared using 2-Word-v2.0.template.dot.





Bernstein and Lee      Expires August 13, 2014                [Page 27]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


APPENDIX A: Encoding Examples

A.1. Wavelength Converter Accessibility Field

   Example:

   Figure 1 shows a wavelength converter pool architecture know as
   "shared per fiber". In this case the input and output pool matrices
   are simply:

              +-----+       +-----+
              | 1 1 |       | 1 0 |
          WI =|     |,  WE =|     |
              | 1 1 |       | 0 1 |
              +-----+       +-----+


                    +-----------+                      +------+
                    |           |--------------------->|      |
                    |           |--------------------->|  C   |
              /|    |           |--------------------->|  o   |
             /D+--->|           |--------------------->|  m   |
            + e+--->|           |                      |  b   |=======>
   ========>| M|    |  Optical  |    +-----------+     |  i   | Port O1
   Port I1  + u+--->|   Switch  |    |  WC Pool  |     |  n   |
             \x+--->|           |    |  +-----+  |     |  e   |
              \|    |           +----+->|WC #1|--+---->|  r   |
                    |           |    |  +-----+  |     +------+
                    |           |    |           |     +------+
              /|    |           |    |  +-----+  |     |      |
             /D+--->|           +----+->|WC #2|--+---->|  C   |
            + e+--->|           |    |  +-----+  |     |  o   |
   ========>| M|    |           |    +-----------+     |  m   |=======>
   Port I2  + u+--->|           |                      |  b   | Port O2
             \x+--->|           |--------------------->|  i   |
              \|    |           |--------------------->|  n   |
                    |           |--------------------->|  e   |
                    |           |--------------------->|  r   |
                    +-----------+                      +------+
    Figure 1 An optical switch featuring a shared per fiber wavelength
                       converter pool architecture.


   This wavelength converter pool can be encoded as follows:





Bernstein and Lee      Expires August 13, 2014                [Page 28]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    Reserved |1|                    Reserved                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                  Note: I1,I2 can connect to either WC1 or WC2
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |0|  Reserved   |            Length = 12        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Link Local Identifier = #1                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Link Local Identifier = #2                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |1|  Reserved   |            Length = 8         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           RB ID = #1                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           RB ID = #2                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                        Note: WC1 can only connect to O1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |1|  Reserved   |            Length = 8         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Link Local Identifier = #1                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |0|  Reserved   |            Length = 8         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            RB ID = #1                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                        Note: WC2 can only connect to O2
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |1|  Reserved   |            Length = 8         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Link Local Identifier = #2                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |0|                |            Length = 8      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            RB ID = #2                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




A.2. Wavelength Conversion Range Field

   Example:



Bernstein and Lee      Expires August 13, 2014                [Page 29]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   This example, based on figure 1, shows how to represent the
   wavelength conversion range of wavelength converters. Suppose the
   wavelength range of input and output of WC1 and WC2 are {L1, L2, L3,
   L4}:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                             Note: WC Set
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Action=0     |1| Reserved    |     Length = 8                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |           WC ID = #1          |       WC ID = #2              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                             Note: wavelength input range
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | 2   | Num Wavelengths = 4     |          Length = 8           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |Grid |  C.S. |     Reserved    |  n for lowest frequency = 1   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                             Note: wavelength output range
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | 2   | Num Wavelengths = 4     |          Length = 8           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |Grid |  C.S. |     Reserved    |  n for lowest frequency = 1   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

A.3. An OEO Switch with DWDM Optics

   Figure 2 shows an electronic switch fabric surrounded by DWDM
   optics. In this example the electronic fabric can handle either
   G.709 or SDH signals only (2.5 or 10 Gbps). To describe this node,
   the following information is needed:

   <Node_Info> ::= <Node_ID>[Other GMPLS info-
   elements][<ConnectivityMatrix>...]  [<ResourcePool>][<RBPoolState>]

   In this case there is complete port to port connectivity so the
   <ConnectivityMatrix> is not required. In addition since there are
   sufficient ports to handle all wavelength signals the <RBPoolState>
   element is not needed.

   Hence the attention will be focused on the <ResourcePool> field:

   <ResourcePool> ::=
   <ResourceBlockInfo>[<RBAccessibility>...][<ResourceWaveConstraints>.
   ..]



Bernstein and Lee      Expires August 13, 2014                [Page 30]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


              /|    +-----------+    +-------------+   +------+
             /D+--->|           +--->|Tunable Laser|-->|      |
            + e+--->|           |    +-------------+   |  C   |
   ========>| M|    |           |        ...           |  o   |=======>
   Port I1  + u+--->|           |    +-------------+   |  m   | Port O1
             \x+--->|           |--->|Tunable Laser|-->|  b   |
              \|    |  Electric |    +-------------+   +------+
                    |   Switch  |
              /|    |           |    +-------------+   +------+
             /D+--->|           +--->|Tunable Laser|-->|      |
            + e+--->|           |    +-------------+   |  C   |
   ========>| M|    |           |        ...           |  o   |=======>
   Port I2  + u+--->|           |    +-------------+   |  m   | Port O2
             \x+--->|           +--->|Tunable Laser|-->|  b   |
              \|    |           |    +-------------+   +------+
                    |           |
              /|    |           |    +-------------+   +------+
             /D+--->|           |--->|Tunable Laser|-->|      |
            + e+--->|           |    +-------------+   |  C   |
   ========>| M|    |           |        ...           |  o   |=======>
   Port I3  + u+--->|           |    +-------------+   |  m   | Port O3
             \x+--->|           |--->|Tunable Laser|-->|  b   |
              \|    +-----------+    +-------------+   +------+

      Figure 2 An optical switch built around an electronic switching
                                  fabric.

   The resource block information will tell us about the processing
   constraints of the receivers, transmitters and the electronic
   switch. The resource availability information, although very simple,
   tells us that all signals must traverse the electronic fabric (fixed
   connectivity). The resource wavelength constraints are not needed
   since there are no special wavelength constraints for the resources
   that would not appear as port/wavelength constraints.

   <ResourceBlockInfo>:













Bernstein and Lee      Expires August 13, 2014                [Page 31]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     RB Set Field                              |
      :  (only one resource block in this example with shared         |
      |                     input/output case)                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|1|                   Reserved                                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                 Optical Interface Class List(s)               |
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Input Client Signal Type                   |
      :                   (G-PIDs for SDH and G.709)                  :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Input Bit Rate Range List                  |
      :                       (2.5Gbps, 10Gbps)                       :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Processing Capabilities List                |
      :              Fixed (non optional) 3R regeneration             :
      :                                                               :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Since there is fixed connectivity to resource blocks (the electronic
   switch) the <RBAccessibility> is:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Connectivity=0|Reserved                                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Input Link Set Field A #1                  |
      :                    (All input links connect to resource)      :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          RB Set Field A #1                    |
      :              (trivial set only one resource block)            :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                Output Link Set Field B #1                     |
      :                    (All output links connect to resource)     :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+









Bernstein and Lee      Expires August 13, 2014                [Page 32]


Internet-Draft   Wavelength Switched Optical Networks     February 2014




8. References

8.1. Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC4328] Papadimitriou, D., Ed., "Generalized Multi-Protocol Label
             Switching (GMPLS) Signaling Extensions for G.709 Optical
             Transport Networks Control", RFC 4328, January 2006.

   [Gen-Encode]   G. Bernstein, Y. Lee, D. Li, W. Imajuku, "General
             Network Element Constraint Encoding for GMPLS Controlled
             Networks", work in progress: draft-ietf-ccamp-general-
             constraint-encode.



8.2. Informative References



   [IEEE]    IEEE, "IEEE Standard for Binary Floating-Point
             Arithmetic", Standard 754-1985, 1985 (ISBN 1-5593-7653-8).

   [G.694.1] ITU-T Recommendation G.694.1, Spectral grids for WDM
             applications: DWDM frequency grid, June 2002.

   [G.694.2] ITU-T Recommendation G.694.2, Spectral grids for WDM
             applications: CWDM wavelength grid, December 2003.

   [G.695]   ITU-T Recommendation G.695, Optical interfaces for coarse
             wavelength division multiplexing applications, October,
             2010.

   [G.959.1] ITU-T Recommendation G.959.1, Optical transport network
             physical layer interfaces, February, 2012.

   [RFC3471] Berger, L., "Generalized Multi-Protocol Label Switching
             (GMPLS) Signaling Functional Description", RFC 3471,
             January 2003.






Bernstein and Lee      Expires August 13, 2014                [Page 33]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   [RFC4203] Kompella, L. and Y. Rekhter, Eds., "OSPF Extensions in
             Support of Generalized Multi-Protocol Label Switching
             (GMPLS)", RFC 4203, October 2005.

   [RFC5307] Kompella, L. and Y. Rekhter, Eds., "IS-IS Extensions in
             Support of Generalized Multi-Protocol Label Switching
             (GMPLS)", RFC 5307, October, 2008.

   [RFC5440] Vasseur, JP. and Le Roux,  JL., Eds., "Path Computation
             Element (PCE) Communication Protocol (PCEP)", RFC 5440,
             March 2009.

   [RFC5920] L. Fang, Ed., "Security Framework for MPLS and GMPLS
             Networks", RFC 5920, July 2010.

   [RFC6205]   T. Otani, H. Guo, K. Miyazaki, D. Caviglia, "Generalized
             Labels for G.694 Lambda-Switching Capable Label Switching
             Routers", RFC 6205, March 2011.

   [RFC6163]  Y. Lee, G. Bernstein, W. Imajuku, "Framework for GMPLS
             and PCE Control of Wavelength Switched Optical Networks",
             RFC 6163, April 2011.

   [RWA-Info]  G. Bernstein, Y. Lee, D. Li, W. Imajuku, "Routing and
             Wavelength Assignment Information Model for Wavelength
             Switched Optical Networks", work in progress: draft-ietf-
             ccamp-rwa-info.






















Bernstein and Lee      Expires August 13, 2014                [Page 34]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


9. Contributors

   Diego Caviglia
   Ericsson
   Via A. Negrone 1/A 16153
   Genoa Italy

   Phone: +39 010 600 3736
   Email: diego.caviglia@ericsson.com

   Anders Gavler
   Acreo AB
   Electrum 236
   SE - 164 40 Kista Sweden

   Email: Anders.Gavler@acreo.se

   Jonas Martensson
   Acreo AB
   Electrum 236
   SE - 164 40 Kista, Sweden

   Email: Jonas.Martensson@acreo.se

   Itaru Nishioka
   NEC Corp.
   1753 Simonumabe, Nakahara-ku, Kawasaki, Kanagawa 211-8666
   Japan

   Phone: +81 44 396 3287
   Email: i-nishioka@cb.jp.nec.com

   Pierre Peloso
   ALU

   Email: pierre.peloso@alcatel-lucent.com

   Cyril Margaria
   Email: cyril.margaria@gmail.com


   Giovanni Martinelli

   Cisco





Bernstein and Lee      Expires August 13, 2014                [Page 35]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   Email: giomarti@cisco.com


   Gabriele M Galimberti
   Cisco
   Email: ggalimbe@cisco.com

   Lyndon Ong
   Ciena Corporation
   Email: lyong@ciena.com

   Daniele Ceccarelli
   Ericsson
   Email: daniele.ceccarelli@ericsson.com



Authors' Addresses

   Greg M. Bernstein (ed.)
   Grotto Networking
   Fremont California, USA

   Phone: (510) 573-2237
   Email: gregb@grotto-networking.com


   Young Lee (ed.)
   Huawei Technologies
   5340 Legacy Drive Build 3
   Plano, TX 75024
   USA

   Phone: (469) 277-5838
   Email: leeyoung@huawei.com












Bernstein and Lee      Expires August 13, 2014                [Page 36]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   Dan Li
   Huawei Technologies Co., Ltd.
   F3-5-B R&D Center, Huawei Base,
   Bantian, Longgang District
   Shenzhen 518129 P.R.China

   Phone: +86-755-28973237
   Email: danli@huawei.com

   Wataru Imajuku
   NTT Network Innovation Labs
   1-1 Hikari-no-oka, Yokosuka, Kanagawa
   Japan

   Phone: +81-(46) 859-4315
   Email: imajuku.wataru@lab.ntt.co.jp



   Jianrui Han
   Huawei Technologies Co., Ltd.
   F3-5-B R&D Center, Huawei Base,
   Bantian, Longgang District
   Shenzhen 518129 P.R.China

   Phone: +86-755-28972916
   Email: hanjianrui@huawei.com


Intellectual Property Statement

   The IETF Trust takes no position regarding the validity or scope of
   any Intellectual Property Rights or other rights that might be
   claimed to pertain to the implementation or use of the technology
   described in any IETF Document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.

   Copies of Intellectual Property disclosures made to the IETF
   Secretariat and any assurances of licenses to be made available, or
   the result of an attempt made to obtain a general license or
   permission for the use of such proprietary rights by implementers or
   users of this specification can be obtained from the IETF on-line
   IPR repository at http://www.ietf.org/ipr




Bernstein and Lee      Expires August 13, 2014                [Page 37]


Internet-Draft   Wavelength Switched Optical Networks     February 2014


   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   any standard or specification contained in an IETF Document. Please
   address the information to the IETF at ietf-ipr@ietf.org.

Disclaimer of Validity

   All IETF Documents and the information contained therein are
   provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION
   HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY,
   THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
   WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
   WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
   ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
   FOR A PARTICULAR PURPOSE.

Acknowledgment

   Funding for the RFC Editor function is currently provided by the
   Internet Society.




























Bernstein and Lee      Expires August 13, 2014                [Page 38]