CoRE T. Fossati
Internet-Draft ARM
Intended status: Standards Track K. Hartke
Expires: September 9, 2019 Ericsson
C. Bormann
Universitaet Bremen TZI
March 08, 2019
Multipart Content-Format for CoAP
draft-ietf-core-multipart-ct-03
Abstract
This memo defines application/multipart-core, an application-
independent media-type that can be used to combine representations of
zero or more different media types into a single message, such as a
CoAP request or response body, with minimal framing overhead, each
along with a CoAP Content-Format identifier.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 9, 2019.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Fossati, et al. Expires September 9, 2019 [Page 1]
Internet-Draft Multipart Content-Format for CoAP March 2019
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Multipart Content-Format Encoding . . . . . . . . . . . . . . 3
3. Usage Examples . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Observing Resources . . . . . . . . . . . . . . . . . . . 4
4. Implementation hints . . . . . . . . . . . . . . . . . . . . 4
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 5
5.1. Registration of media type application/multipart-core . . 5
5.2. Registration of a Content-Format identifier for
application/multipart-core . . . . . . . . . . . . . . . 7
6. Security Considerations . . . . . . . . . . . . . . . . . . . 7
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.1. Normative References . . . . . . . . . . . . . . . . . . 7
7.2. Informative References . . . . . . . . . . . . . . . . . 7
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
This memo defines application/multipart-core, an application-
independent media-type that can be used to combine representations of
zero or more different media types into a single message, such as a
CoAP [RFC7252] request or response body, with minimal framing
overhead, each along with a CoAP Content-Format identifier.
This simple and efficient binary framing mechanism can be employed to
create application specific request and response bodies which build
on multiple already existing media types.
The individual representations in an application/multipart-core body
occur in a sequence, which may be employed by an application where
such a sequence is natural, e.g. for a number of audio snippets in
different formats to be played out in that sequence.
In other cases, an application may be more interested in a bag of
representations, which are distinguished by their Content-Format
identifier, such as an audio snippet and a text representation
accompanying it. In such a case, the sequence in which these occur
may not be relevant to the application. This specification allows to
indicate that an optional part is not present by substituting a null
value for the representation of the part.
Fossati, et al. Expires September 9, 2019 [Page 2]
Internet-Draft Multipart Content-Format for CoAP March 2019
A third situation that is common only ever has a single
representation in the sequence, which is one of a set of formats
possible. This kind of union of formats may also make the presence
of the actual representation optional, the omission of which leads to
a zero-length array.
Where these rules are not sufficient for an application, it might
still use the general format defined here, but register a new media
type and an associated Content-Format identifier to associate the
representation with these more specific semantics instead of using
application/multipart-core.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Multipart Content-Format Encoding
A representation of media-type application/multipart-core contains a
collection of zero or more representations, each along with their
respective content format.
The collection is encoded as a CBOR [RFC7049] array with an even
number of elements. The second, fourth, sixth, etc. element is a
byte string containing a representation, or the value "null" if an
optional part is indicated as not given. The first, third, fifth,
etc. element is an unsigned integer specifying the content format ID
of the representation following it.
For example, a collection containing two representations, one with
content format ID 42 and one with content format ID 0, looks like
this in CBOR diagnostic notation:
[42, h'0123456789abcdef', 0, h'3031323334']
For illustration, the structure of an application/multipart-core
representation can be described by the CDDL [I-D.ietf-cbor-cddl]
specification in Figure 1:
multipart-core = [* multipart-part]
multipart-part = (type: uint .size 2, part: bytes / null)
Figure 1: CDDL for application/multipart-core
Fossati, et al. Expires September 9, 2019 [Page 3]
Internet-Draft Multipart Content-Format for CoAP March 2019
This format is intended as a strict specification: An implementation
MUST stop processing the representation if there is a CBOR well-
formedness error, a deviation from the structure defined above, or
any residual data left after processing the CBOR data item. (This
generally means the representation is not processed at all except if
some streaming processing has already happened.)
3. Usage Examples
3.1. Observing Resources
When a client registers to observe a resource [RFC7641] for which no
representation is available yet, the server may send one or more 2.05
(Content) notifications before sending the first actual 2.05
(Content) or 2.03 (Valid) notification. The possible resulting
sequence of notifications is shown in Figure 1.
__________ __________ __________
| | | | | |
---->| 2.05 |---->| 2.05 / |---->| 4.xx / |
| Pending | | 2.03 | | 5.xx |
|__________| |__________| |__________|
^ \ \ ^ \ ^
\__/ \ \___/ /
\_______________________/
Figure 2: Sequence of Notifications:
The specification of the Observe option requires that all
notifications carry the same Content-Format. The application/
multipart-core media type can be used to provide that Content-Format:
e.g., carrying an empty list of representations in the case marked as
"Pending" in Figure 2, and carrying a single representation specified
as the target content-format in the case in the middle of the figure.
4. Implementation hints
This section describes the serialization for readers that may be new
to CBOR. It does not contain any new information.
An application/multipart-core representation carrying no
representations is represented by an empty CBOR array, which is
serialized as a single byte with the value 0x80.
An application/multipart-core representation carrying a single
representation is represented by a two-element CBOR array, which is
serialized as 0x82 followed by the two elements. The first element
is an unsigned integer for the Content-Format value, which is
Fossati, et al. Expires September 9, 2019 [Page 4]
Internet-Draft Multipart Content-Format for CoAP March 2019
represented as described in Table 1. The second element is the
object as a byte string, which is represented as a length as
described in Table 2 followed by the bytes of the object.
+----------------+------------+
| Serialization | Value |
+----------------+------------+
| 0x00..0x17 | 0..23 |
| 0x18 0xnn | 24..255 |
| 0x19 0xnn 0xnn | 256..65535 |
+----------------+------------+
Table 1: Serialization of content-format
+-----------------------------+-------------------+
| Serialization | Length |
+-----------------------------+-------------------+
| 0x40..0x57 | 0..23 |
| 0x58 0xnn | 24..255 |
| 0x59 0xnn 0xnn | 256..65535 |
| 0x5a 0xnn 0xnn 0xnn 0xnn | 65536..4294967295 |
| 0x5b 0xnn .. 0xnn (8 bytes) | 4294967296.. |
+-----------------------------+-------------------+
Table 2: Serialization of object length
For example, a single text/plain object (content-format 0) of value
"Hello World" (11 characters) would be serialized as
0x82 0x00 0x4b H e l l o 0x20 w o r l d
In effect, the serialization for a single object is done by prefixing
the object with information that there is one object (here: 0x82),
about its content-format (here: 0x00) and its length (here: 0x4b).
For more than one representation included in an application/
multipart-core representation, the head of the CBOR array is adjusted
(0x84 for two representations, 0x86 for three, ...) and the sequences
of content-format and embedded representations follow.
5. IANA Considerations
5.1. Registration of media type application/multipart-core
IANA is requested to register the following media type [RFC6838]:
Type name: application
Fossati, et al. Expires September 9, 2019 [Page 5]
Internet-Draft Multipart Content-Format for CoAP March 2019
Subtype name: multipart-core
Required parameters: N/A
Optional parameters: N/A
Encoding considerations: binary
Security considerations: See the Security Considerations Section of
RFCthis
Interoperability considerations: N/A
Published specification: RFCthis
Applications that use this media type: Applications that need to
combine representations of zero or more different media types into
one, e.g., EST-CoAP [I-D.ietf-ace-coap-est]
Fragment identifier considerations: The syntax and semantics of
fragment identifiers specified for "application/multipart-core" is
as specified for "application/cbor". (At publication of this
document, there is no fragment identification syntax defined for
"application/cbor".)
Additional information:
Deprecated alias names for this type: N/A
Magic number(s): N/A
File extension(s): N/A
Macintosh file type code(s): N/A
Person & email address to contact for further information:
iesg&ietf.org
Intended usage: COMMON
Restrictions on usage: N/A
Author: CoRE WG
Change controller: IESG
Provisional registration? (standards tree only): no
Fossati, et al. Expires September 9, 2019 [Page 6]
Internet-Draft Multipart Content-Format for CoAP March 2019
5.2. Registration of a Content-Format identifier for application/
multipart-core
IANA is requested to register the following Content-Format to the
"CoAP Content-Formats" subregistry, within the "Constrained RESTful
Environments (CoRE) Parameters" registry, from the Expert Review
space (0..255):
+----------------------------+----------+------+-----------+
| Media Type | Encoding | ID | Reference |
+----------------------------+----------+------+-----------+
| application/multipart-core | -- | TBD1 | RFCthis |
+----------------------------+----------+------+-----------+
6. Security Considerations
The security considerations of [RFC7049] apply. In particular,
resource exhaustion attacks may employ large values for the byte
string size fields, or deeply nested structures of recursively
embedded application/multipart-core representations.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7049] Bormann, C. and P. Hoffman, "Concise Binary Object
Representation (CBOR)", RFC 7049, DOI 10.17487/RFC7049,
October 2013, <https://www.rfc-editor.org/info/rfc7049>.
[RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
Application Protocol (CoAP)", RFC 7252,
DOI 10.17487/RFC7252, June 2014,
<https://www.rfc-editor.org/info/rfc7252>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
7.2. Informative References
Fossati, et al. Expires September 9, 2019 [Page 7]
Internet-Draft Multipart Content-Format for CoAP March 2019
[I-D.ietf-ace-coap-est]
Stok, P., Kampanakis, P., Richardson, M., and S. Raza,
"EST over secure CoAP (EST-coaps)", draft-ietf-ace-coap-
est-10 (work in progress), March 2019.
[I-D.ietf-cbor-cddl]
Birkholz, H., Vigano, C., and C. Bormann, "Concise data
definition language (CDDL): a notational convention to
express CBOR and JSON data structures", draft-ietf-cbor-
cddl-07 (work in progress), February 2019.
[RFC6838] Freed, N., Klensin, J., and T. Hansen, "Media Type
Specifications and Registration Procedures", BCP 13,
RFC 6838, DOI 10.17487/RFC6838, January 2013,
<https://www.rfc-editor.org/info/rfc6838>.
[RFC7641] Hartke, K., "Observing Resources in the Constrained
Application Protocol (CoAP)", RFC 7641,
DOI 10.17487/RFC7641, September 2015,
<https://www.rfc-editor.org/info/rfc7641>.
Acknowledgements
Most of the text in this draft is from earlier contributions by two
of the authors, Thomas Fossati and Klaus Hartke. The re-mix in this
document is based on the requirements in [I-D.ietf-ace-coap-est],
based on discussions with Michael Richardson, Panos Kampanis and
Peter van der Stok.
Authors' Addresses
Thomas Fossati
ARM
Email: thomas.fossati@arm.com
Klaus Hartke
Ericsson
Torshamnsgatan 23
Stockholm SE-16483
Sweden
Email: klaus.hartke@ericsson.com
Fossati, et al. Expires September 9, 2019 [Page 8]
Internet-Draft Multipart Content-Format for CoAP March 2019
Carsten Bormann
Universitaet Bremen TZI
Postfach 330440
Bremen D-28359
Germany
Phone: +49-421-218-63921
Email: cabo@tzi.org
Fossati, et al. Expires September 9, 2019 [Page 9]