Internet Engineering Task Force J. Bound
INTERNET DRAFT Compaq
DHC Working Group M. Carney
Obsoletes: draft-ietf-dhc-dhcpv6-22.txt Sun Microsystems, Inc
C. Perkins
Nokia Research Center
Ted Lemon
Nominum
Bernie Volz
Ericsson
R. Droms(ed.)
Cisco Systems
1 Feb 2002
Dynamic Host Configuration Protocol for IPv6 (DHCPv6)
draft-ietf-dhc-dhcpv6-23.txt
Status of This Memo
This document is a submission by the Dynamic Host Configuration
Working Group of the Internet Engineering Task Force (IETF). Comments
should be submitted to the dhcwg@ietf.org mailing list.
Distribution of this memo is unlimited.
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at
any time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at:
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at:
http://www.ietf.org/shadow.html.
Abstract
The Dynamic Host Configuration Protocol for IPv6 (DHCP) enables
DHCP servers to pass configuration parameters such as IPv6 network
addresses to IPv6 nodes. It offers the capability of automatic
allocation of reusable network addresses and additional configuration
flexibility. This protocol is a stateful counterpart to "IPv6
Droms (ed.), et al. Expires 1 Aug 2002 [Page i]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Stateless Address Autoconfiguration" [21], and can be used separately
or concurrently with the latter to obtain configuration parameters.
Contents
Status of This Memo i
Abstract i
1. Introduction 1
2. Requirements 2
3. Background 2
4. Design Goals 3
5. Non-Goals 4
6. Terminology 4
6.1. IPv6 Terminology . . . . . . . . . . . . . . . . . . . . 4
6.2. DHCP Terminology . . . . . . . . . . . . . . . . . . . . 5
7. DHCP Constants 7
7.1. Multicast Addresses . . . . . . . . . . . . . . . . . . . 7
7.2. UDP ports . . . . . . . . . . . . . . . . . . . . . . . . 7
7.3. DHCP message types . . . . . . . . . . . . . . . . . . . 8
7.4. Status Codes . . . . . . . . . . . . . . . . . . . . . . 9
7.4.1. Generic Status Codes . . . . . . . . . . . . . . 9
7.4.2. Server-specific Status Codes . . . . . . . . . . 10
7.5. Configuration Variables . . . . . . . . . . . . . . . . . 11
8. Message Formats 11
8.1. DHCP Solicit Message Format . . . . . . . . . . . . . . . 12
8.2. DHCP Advertise Message Format . . . . . . . . . . . . . . 12
8.3. DHCP Request Message Format . . . . . . . . . . . . . . . 12
8.4. DHCP Confirm Message Format . . . . . . . . . . . . . . . 13
8.5. DHCP Renew Message Format . . . . . . . . . . . . . . . . 13
8.6. DHCP Rebind Message Format . . . . . . . . . . . . . . . 13
8.7. DHCP Reply Message Format . . . . . . . . . . . . . . . . 13
8.8. DHCP Release Message Format . . . . . . . . . . . . . . . 13
8.9. DHCP Decline Message Format . . . . . . . . . . . . . . . 14
8.10. DHCP Reconfigure Message Format . . . . . . . . . . . . . 14
8.11. Information-Request Message Format . . . . . . . . . . . 14
9. Relay messages 14
9.1. Relay-forward message . . . . . . . . . . . . . . . . . . 15
9.2. Relay-reply message . . . . . . . . . . . . . . . . . . . 16
10. Representation and use of domain names 16
11. DHCP unique identifier (DUID) 16
Droms (ed.), et al. Expires 1 Aug 2002 [Page ii]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
11.1. DUID contents . . . . . . . . . . . . . . . . . . . . . . 17
11.2. DUID based on link-layer address plus time . . . . . . . 17
11.3. Vendor-assigned unique ID (VUID) . . . . . . . . . . . . 18
11.4. Link-layer address . . . . . . . . . . . . . . . . . . . 19
12. Identity association 20
13. Selecting addresses for assignment to an IA 21
14. Management of temporary addresses 22
15. Reliability of Client Initiated Message Exchanges 23
16. Message validation 24
16.1. Use of Transaction-ID field . . . . . . . . . . . . . . . 24
16.2. Solicit message . . . . . . . . . . . . . . . . . . . . . 25
16.3. Advertise message . . . . . . . . . . . . . . . . . . . . 25
16.4. Request message . . . . . . . . . . . . . . . . . . . . . 25
16.5. Confirm message . . . . . . . . . . . . . . . . . . . . . 25
16.6. Renew message . . . . . . . . . . . . . . . . . . . . . . 26
16.7. Rebind message . . . . . . . . . . . . . . . . . . . . . 26
16.8. Decline messages . . . . . . . . . . . . . . . . . . . . 26
16.9. Release message . . . . . . . . . . . . . . . . . . . . . 27
16.10. Reply message . . . . . . . . . . . . . . . . . . . . . . 27
16.11. Reconfigure message . . . . . . . . . . . . . . . . . . . 27
16.12. Information-request message . . . . . . . . . . . . . . . 27
16.13. Relay-forward message . . . . . . . . . . . . . . . . . . 28
16.14. Relay-reply message . . . . . . . . . . . . . . . . . . . 28
17. Client Source Address and Interface Selection 28
18. DHCP Server Solicitation 28
18.1. Client Behavior . . . . . . . . . . . . . . . . . . . . . 29
18.1.1. Creation of Solicit messages . . . . . . . . . . 29
18.1.2. Transmission of Solicit Messages . . . . . . . . 29
18.1.3. Receipt of Advertise messages . . . . . . . . . . 30
18.2. Server Behavior . . . . . . . . . . . . . . . . . . . . . 31
18.2.1. Receipt of Solicit messages . . . . . . . . . . . 31
18.2.2. Creation and transmission of Advertise messages . 31
19. DHCP Client-Initiated Configuration Exchange 32
19.1. Client Behavior . . . . . . . . . . . . . . . . . . . . . 33
19.1.1. Creation and transmission of Request messages . . 33
19.1.2. Creation and transmission of Confirm messages . . 34
19.1.3. Creation and transmission of Renew messages . . . 35
19.1.4. Creation and transmission of Rebind messages . . 37
19.1.5. Creation and Transmission of Information-request
messages . . . . . . . . . . . . . . . . . 38
19.1.6. Receipt of Reply message in response to a Request,
Confirm, Renew, Rebind or Information-request
message . . . . . . . . . . . . . . . . . 38
19.1.7. Creation and transmission of Release messages . . 40
Droms (ed.), et al. Expires 1 Aug 2002 [Page iii]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
19.1.8. Receipt of Reply message in response to a Release
message . . . . . . . . . . . . . . . . . 41
19.1.9. Creation and transmission of Decline messages . . 41
19.1.10. Receipt of Reply message in response to a Decline
message . . . . . . . . . . . . . . . . . 42
19.2. Server Behavior . . . . . . . . . . . . . . . . . . . . . 42
19.2.1. Receipt of Request messages . . . . . . . . . . . 42
19.2.2. Receipt of Confirm messages . . . . . . . . . . . 43
19.2.3. Receipt of Renew messages . . . . . . . . . . . . 44
19.2.4. Receipt of Rebind messages . . . . . . . . . . . 45
19.2.5. Receipt of Information-request messages . . . . . 46
19.2.6. Receipt of Release messages . . . . . . . . . . . 47
19.2.7. Receipt of Decline messages . . . . . . . . . . . 47
19.2.8. Transmission of Reply messages . . . . . . . . . 47
20. DHCP Server-Initiated Configuration Exchange 48
20.1. Server Behavior . . . . . . . . . . . . . . . . . . . . . 48
20.1.1. Creation and transmission of Reconfigure messages 48
20.1.2. Time out and retransmission of Reconfigure
messages . . . . . . . . . . . . . . . . . 49
20.1.3. Receipt of Renew messages . . . . . . . . . . . . 49
20.2. Receipt of Information-request messages . . . . . . . . . 49
20.3. Client Behavior . . . . . . . . . . . . . . . . . . . . . 50
20.3.1. Receipt of Reconfigure messages . . . . . . . . . 50
20.3.2. Creation and transmission of Renew messages . . . 51
20.3.3. Creation and transmission of Information-request
messages . . . . . . . . . . . . . . . . . 51
20.3.4. Time out and retransmission of Renew or
Information-request messages . . . . . . . 51
20.3.5. Receipt of Reply messages . . . . . . . . . . . . 51
21. Relay Behavior 52
21.1. Relaying of client messages . . . . . . . . . . . . . . . 52
21.2. Relaying of server messages . . . . . . . . . . . . . . . 52
22. Authentication of DHCP messages 53
22.1. DHCP threat model . . . . . . . . . . . . . . . . . . . . 53
22.2. Security of messages sent between servers and relay agents 54
22.3. Summary of DHCP authentication . . . . . . . . . . . . . 54
22.4. Replay detection . . . . . . . . . . . . . . . . . . . . 54
22.5. Configuration token protocol . . . . . . . . . . . . . . 54
22.6. Delayed authentication protocol . . . . . . . . . . . . . 55
22.6.1. Management issues in the delayed authentication
protocol . . . . . . . . . . . . . . . . . 55
22.6.2. Use of the Authentication option in the delayed
authentication protocol . . . . . . . . . 55
22.6.3. Message validation . . . . . . . . . . . . . . . 56
22.6.4. Key utilization . . . . . . . . . . . . . . . . . 57
22.6.5. Client considerations for delayed authentication
protocol . . . . . . . . . . . . . . . . . 57
22.6.6. Server considerations for delayed authentication
protocol . . . . . . . . . . . . . . . . . 59
Droms (ed.), et al. Expires 1 Aug 2002 [Page iv]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
23. DHCP options 60
23.1. Format of DHCP options . . . . . . . . . . . . . . . . . 60
23.2. Client Identifier option . . . . . . . . . . . . . . . . 60
23.3. Server Identifier option . . . . . . . . . . . . . . . . 61
23.4. Identity association option . . . . . . . . . . . . . . . 61
23.5. IA Address option . . . . . . . . . . . . . . . . . . . . 63
23.6. Requested Temporary Addresses (RTA) Option . . . . . . . 65
23.7. Option Request option . . . . . . . . . . . . . . . . . . 65
23.8. Preference option . . . . . . . . . . . . . . . . . . . . 66
23.9. Elapsed Time . . . . . . . . . . . . . . . . . . . . . . 67
23.10. Client message option . . . . . . . . . . . . . . . . . . 67
23.11. Server message option . . . . . . . . . . . . . . . . . . 68
23.12. Authentication option . . . . . . . . . . . . . . . . . . 68
23.13. Server unicast option . . . . . . . . . . . . . . . . . . 69
23.14. Status Code Option . . . . . . . . . . . . . . . . . . . 70
23.15. User Class Option . . . . . . . . . . . . . . . . . . . . 70
23.16. Vendor Class Option . . . . . . . . . . . . . . . . . . . 71
23.17. Interface-Id Option . . . . . . . . . . . . . . . . . . . 72
24. Security Considerations 73
25. Year 2000 considerations 73
26. IANA Considerations 74
26.1. Multicast addresses . . . . . . . . . . . . . . . . . . . 74
26.2. DHCPv6 message types . . . . . . . . . . . . . . . . . . 74
26.3. DUID . . . . . . . . . . . . . . . . . . . . . . . . . . 74
26.4. DHCPv6 options . . . . . . . . . . . . . . . . . . . . . 74
26.5. Status codes . . . . . . . . . . . . . . . . . . . . . . 74
26.6. Authentication option . . . . . . . . . . . . . . . . . . 75
27. Acknowledgments 75
References 75
Chair's Address 77
Authors' Addresses 77
A. Appearance of Options in Message Types 79
B. Appearance of Options in the Options Field of DHCP Messages 79
C. Full Copyright Statement 80
1. Introduction
This document describes DHCP for IPv6 (DHCP), a UDP [19]
client/server protocol designed to reduce the cost of management
of IPv6 nodes in environments where network managers require more
control over the allocation of IPv6 addresses and configuration
of network stack parameters than that offered by "IPv6 Stateless
Droms (ed.), et al. Expires 1 Aug 2002 [Page 1]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Address Autoconfiguration" [21]. DHCP is a stateful counterpart to
stateless autoconfiguration. Note that both stateful and stateless
autoconfiguration can be used concurrently in the same environment,
leveraging the strengths of both mechanisms in order to reduce the
cost of ownership and management of network nodes.
DHCP reduces the cost of ownership by centralizing the management
of network resources such as IP addresses, routing information, OS
installation information, directory service information, and other
such information on a few DHCP servers, rather than distributing such
information in local configuration files among all network node.
DHCP is designed to be easily extended to carry new configuration
parameters through the addition of new DHCP "options" defined to
carry this information.
Those readers familiar with DHCP for IPv4 [7] will find DHCP for
IPv6 provides a superset of the features of DHCP and benefits from
the additional features of IPv6 and freedom from the constraints of
backward compatibility with BOOTP [4].
2. Requirements
The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL, when they appear in this
document, are to be interpreted as described in [2].
This document also makes use of internal conceptual variables
to describe protocol behavior and external variables that an
implementation must allow system administrators to change. The
specific variable names, how their values change, and how their
settings influence protocol behavior are provided to demonstrate
protocol behavior. An implementation is not required to have them in
the exact form described here, so long as its external behavior is
consistent with that described in this document.
3. Background
The IPv6 Specification provides the base architecture and design of
IPv6. Related work in IPv6 that would best serve an implementor
to study includes the IPv6 Specification [5], the IPv6 Addressing
Architecture [9], IPv6 Stateless Address Autoconfiguration [21], IPv6
Neighbor Discovery Processing [17], and Dynamic Updates to DNS [22].
These specifications enable DHCP to build upon the IPv6 work to
provide both robust stateful autoconfiguration and autoregistration
of DNS Host Names.
The IPv6 Addressing Architecture specification [9] defines the
address scope that can be used in an IPv6 implementation, and the
various configuration architecture guidelines for network designers
of the IPv6 address space. Two advantages of IPv6 are that support
for multicast is required, and nodes can create link-local addresses
Droms (ed.), et al. Expires 1 Aug 2002 [Page 2]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
during initialization. This means that a client can immediately use
its link-local address and a well-known multicast address to begin
communications to discover neighbors on the link. For instance, a
client can send a Solicit message and locate a server or relay.
IPv6 Stateless Address Autoconfiguration [21] specifies procedures
by which a node may autoconfigure addresses based on router
advertisements [17], and the use of a valid lifetime to support
renumbering of addresses on the Internet. In addition the
protocol interaction by which a node begins stateless or stateful
autoconfiguration is specified. DHCP is one vehicle to perform
stateful autoconfiguration. Compatibility with stateless address
autoconfiguration is a design requirement of DHCP (see Section 4).
IPv6 Neighbor Discovery [17] is the node discovery protocol in IPv6
which replaces and enhances functions of ARP [18]. To understand
IPv6 and stateless address autoconfiguration it is strongly
recommended that implementors understand IPv6 Neighbor Discovery.
Dynamic Updates to DNS [22] is a specification that supports the
dynamic update of DNS records for both IPv4 and IPv6. DHCP can use
the dynamic updates to DNS to integrate addresses and name space to
not only support autoconfiguration, but also autoregistration in
IPv6.
4. Design Goals
- DHCP is a mechanism rather than a policy. Network administrators
set their administrative policies through the configuration
parameters they place upon the DHCP servers in the DHCP domain
they're managing. DHCP is simply used to deliver parameters
according to that policy to each of the DHCP clients within the
domain.
- DHCP is compatible with IPv6 stateless address
autoconfiguration [21], statically configured, non-participating
nodes and with existing network protocol implementations.
- DHCP does not require manual configuration of network parameters
on DHCP clients, except in cases where such configuration is
needed for security reasons. A node configuring itself using
DHCP should require no user intervention.
- DHCP does not require a server on each link. To allow for scale
and economy, DHCP must work across DHCP relays.
- DHCP clients can operate on a link without IPv6 routers present.
- DHCP will provide the ability to renumber network(s) when
required by network administrators [3].
Droms (ed.), et al. Expires 1 Aug 2002 [Page 3]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
- A DHCP client can make multiple, different requests for
configuration parameters when necessary from one or more DHCP
servers at any time.
- DHCP will contain the appropriate time out and retransmission
mechanisms to efficiently operate in environments with high
latency and low bandwidth characteristics.
5. Non-Goals
This specification explicitly does not cover the following:
- Specification of a DHCP server to server protocol.
- How a DHCP server stores its DHCP data.
- How to manage a DHCP domain or DHCP server.
- How a DHCP relay is configured or what sort of information it may
log.
6. Terminology
This sections defines terminology specific to IPv6 and DHCP used in
this document.
6.1. IPv6 Terminology
IPv6 terminology relevant to this specification from the IPv6
Protocol [5], IPv6 Addressing Architecture [9], and IPv6 Stateless
Address Autoconfiguration [21] is included below.
address An IP layer identifier for an interface
or a set of interfaces.
unicast address An identifier for a single interface.
A packet sent to a unicast address is
delivered to the interface identified by
that address.
multicast address An identifier for a set of interfaces
(typically belonging to different
nodes). A packet sent to a multicast
address is delivered to all interfaces
identified by that address.
host Any node that is not a router.
IP Internet Protocol Version 6 (IPv6). The
terms IPv4 and IPv6 are used only in
Droms (ed.), et al. Expires 1 Aug 2002 [Page 4]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
contexts where it is necessary to avoid
ambiguity.
interface A node's attachment to a link.
link A communication facility or medium over
which nodes can communicate at the link
layer, i.e., the layer immediately below
IP. Examples are Ethernet (simple or
bridged); Token Ring; PPP links, X.25,
Frame Relay, or ATM networks; and
Internet (or higher) layer "tunnels",
such as tunnels over IPv4 or IPv6
itself.
link-layer identifier A link-layer identifier for an
interface. Examples include IEEE 802
addresses for Ethernet or Token Ring
network interfaces, and E.164 addresses
for ISDN links.
link-local address An IPv6 address having link-only
scope, indicated by having the prefix
(FE80::0000/64), that can be used to
reach neighboring nodes attached to
the same link. Every interface has a
link-local address.
neighbor A node attached to the same link.
node A device that implements IP.
packet An IP header plus payload.
prefix The initial bits of an address, or a
set of IP address that share the same
initial bits.
prefix length The number of bits in a prefix.
router A node that forwards IP packets not
explicitly addressed to itself.
6.2. DHCP Terminology
Terminology specific to DHCP can be found below.
agent address The address of a neighboring DHCP Agent
on the same link as the DHCP client.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 5]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
binding A binding (or, client binding) is a
group of server data records containing
the information the server has about
the addresses in an IA and any other
configuration information assigned to
the client. A binding is indexed by the
tuple <DUID, IAID>.
DHCP Dynamic Host Configuration Protocol
for IPv6. The terms DHCPv4 and DHCPv6
are used only in contexts where it is
necessary to avoid ambiguity.
configuration parameter An element of the configuration
information set on the server and
delivered to the client using DHCP.
Such parameters may be used to carry
information to be used by a node to
configure its network subsystem and
enable communication on a link or
internetwork, for example.
DHCP client (or client) A node that initiates requests on a link
to obtain configuration parameters from
one or more DHCP servers.
DHCP domain A set of links managed by DHCP and
operated by a single administrative
entity.
DHCP server (or server) A server is a node that responds to
requests from clients, and may or
may not be on the same link as the
client(s).
DHCP relay (or relay) A node that acts as an intermediary to
deliver DHCP messages between clients
and servers, and is on the same link as
a client.
DHCP agent (or agent) Either a DHCP server on the same link as
a client, or a DHCP relay.
DUID A DHCP Unique IDentifier for a DHCP
participant; each DHCP client and server
has exactly one DUID.
Identity association (IA) A collection of addresses assigned to
a client. Each IA has an associated
IAID. An IA may have 0 or more addresses
associated with it.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 6]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Identity association identifier (IAID) An identifier for an IA,
chosen by the client. Each IA has an
IAID, which is chosen to be unique among
all IAIDs for IAs belonging to that
client.
message A unit of data carried in a packet,
exchanged between DHCP agents and
clients.
transaction-ID An unsigned integer to match responses
with replies initiated either by a
client or server.
7. DHCP Constants
This section describes various program and networking constants used
by DHCP.
7.1. Multicast Addresses
DHCP makes use of the following multicast addresses:
All_DHCP_Agents (FF02::1:2) This link-scoped multicast address
is used by clients to communicate with the
on-link agent(s) when they do not know the
link-local address(es) for those agents. All
agents (servers and relays) are members of this
multicast group.
All_DHCP_Servers (FF05::1:3) This site-scoped multicast address is
used by clients or relays to communicate with
server(s), either because they want to send
messages to all servers or because they do not
know the server(s) unicast address(es). Note
that in order for a client to use this address,
it must have an address of sufficient scope to
be reachable by the server(s). All servers
within the site are members of this multicast
group.
7.2. UDP ports
DHCP uses the following destination UDP [19] port numbers. While
source ports MAY be arbitrary, client implementations SHOULD permit
their specification through a local configuration parameter to
facilitate the use of DHCP through firewalls.
546 Client port. Used by servers as the destination port
for messages sent to clients and relays. Used by relay
Droms (ed.), et al. Expires 1 Aug 2002 [Page 7]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
agents as the destination port for messages sent to
clients.
547 Agent port. Used as the destination port by clients
for messages sent to agents. Used as the destination
port by relays for messages sent to servers.
7.3. DHCP message types
DHCP defines the following message types. More detail on these
message types can be found in Section 8. Message types not listed
here are reserved for future use. The message code for each message
type is shown with the message name.
SOLICIT (1) The Solicit message is used by clients to
locate servers.
ADVERTISE (2) The Advertise message is used by servers
responding to Solicits.
REQUEST (3) The Request message is used by clients to
request configuration parameters from servers.
CONFIRM (4) The Confirm message is used by clients to
confirm that the addresses assigned to an IA
and the lifetimes for those addresses, as
well as the current configuration parameters
assigned by the server to the client are still
valid.
RENEW (5) The Renew message is used by clients to
update the addresses assigned to an IA and the
lifetimes for those addresses, as well as the
current configuration parameters assigned by
the server to the client. A client sends a
Renew message to the server that originally
populated the IA at time T1.
REBIND (6) The Rebind message is used by clients to extend
the lifetimes of addresses assigned to an IA,
as well as the current configuration parameters
assigned by the server to the client. A
client sends a Rebind message to all available
DHCP servers at time T2 only after the client
has been unable to contact the server that
originally populated the IA with a Renew
message.
REPLY (7) The Reply message is used by servers
responding to Request, Confirm, Renew, Rebind,
Information-request, Release and Decline
messages. In the case of responding to
Droms (ed.), et al. Expires 1 Aug 2002 [Page 8]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
a Request, Confirm, Information-request,
Renew or Rebind message, the Reply contains
configuration parameters destined for the
client.
RELEASE (8) The Release message is used by clients to
indicate to a server that the client will no
longer use one or more addresses in an IA.
DECLINE (9) The Decline message is used by clients to
indicate that the client has determined that
one or more addresses in an IA are already
in use on the link to which the client is
connected.
RECONFIGURE (10) The Reconfigure message is sent by a server
to inform a client that the server has new or
updated configuration parameters, and that
the client is to initiate a Renew/Reply or
Information-request/Reply transaction with
the server in order to receive the updated
information.
INFORMATION-REQUEST (11) The Information-request message is sent
by clients to request configuration parameters
without the assignment of any IP addresses to
the client.
RELAY-FORW (12) The Relay-forward message is used by relays to
forward client messages to servers. The client
message is encapsulated in an option in the
Relay-forward message.
RELAY-REPL (13) The Relay-reply message is used by servers to
send messages to clients through a relay. The
server encapsulates the client message as an
option in the Relay-reply message, which the
relay extracts and forwards to the client.
7.4. Status Codes
This section describes status codes exchanged between DHCP
implementations. These status codes may appear in the Status Code
option or in the status field of an IA.
7.4.1. Generic Status Codes
The status codes in this section are used between clients and servers
to convey status conditions. The following table contains the status
codes, the name for each code (as used in this document) and a brief
Droms (ed.), et al. Expires 1 Aug 2002 [Page 9]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
description. Note that the numeric values do not start at 1, nor are
they consecutive. The status codes are organized in logical groups.
Name Code Description
---------- ---- -----------
Success 0 Success
UnspecFail 16 Failure, reason unspecified
AuthFailed 17 Authentication failed or nonexistent
PoorlyFormed 18 Poorly formed message
AddrUnavail 19 Addresses unavailable
OptionUnavail 20 Requested options unavailable
7.4.2. Server-specific Status Codes
The status codes in this section are used by servers to convey status
conditions to clients. The following table contains the status
codes, the name for each code (as used in this document) and a brief
description. Note that the numeric values do not start at 1, nor are
they consecutive. The status codes are organized in logical groups.
Name Code Description
---- ---- -----------
NoBinding 32 Client record (binding) unavailable
ConfNoMatch 33 Client record Confirm doesn't match IA
RenwNoMatch 34 Client record Renew doesn't match IA
RebdNoMatch 35 Client record Rebind doesn't match IA
InvalidSource 36 Invalid Client IP address
NoPrefixMatch 37 One or more prefixes of the addresses
in the IA is not valid for the link
from which the client message was received
Droms (ed.), et al. Expires 1 Aug 2002 [Page 10]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
7.5. Configuration Variables
This section presents a table of client and server configuration
variables and the default or initial values for these variables.
Parameter Default Description
-------------------------------------
MIN_SOL_DELAY 1 sec Min delay of first Solicit
MAX_SOL_DELAY 5 secs Max delay of first Solicit
SOL_TIMEOUT 500 msecs Initial Solicit timeout
SOL_MAX_RT 30 secs Max Solicit timeout value
REQ_TIMEOUT 250 msecs Initial Request timeout
REQ_MAX_RT 30 secs Max Request timeout value
REQ_MAX_RC 10 Max Request retry attempts
CNF_TIMEOUT 250 msecs Initial Confirm timeout
CNF_MAX_RT 1 sec Max Confirm timeout
CNF_MAX_RD 10 secs Max Confirm duration
REN_TIMEOUT 10 sec Initial Renew timeout
REN_MAX_RT 600 secs Max Renew timeout value
REB_TIMEOUT 10 secs Initial Rebind timeout
REB_MAX_RT 600 secs Max Rebind timeout value
INF_TIMEOUT 500 ms Initial Information-request timeout
INF_MAX_RT 30 secs Max Information-request timeout value
REL_TIMEOUT 250 msecs Initial Release timeout
REL_MAX_RT 1 sec Max Release timeout
REL_MAX_RC 5 MAX Release attempts
DEC_TIMEOUT 250 msecs Initial Decline timeout
DEC_MAX_RT 1 sec Max Decline timeout
DEC_MAX_RC 5 Max Decline attempts
8. Message Formats
All DHCP messages sent between clients and servers share an identical
fixed format header and a variable format area for options. Not all
fields in the header are used in every message.
All values in the message header and in options are in network order.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 11]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The following diagram illustrates the format of DHCP messages sent
between clients and servers:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type | transaction-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. options .
. (variable) .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The following sections describe the use of the fields in the DHCP
message header in each of the DHCP messages. In these descriptions,
fields that are not used in a message are marked as "unused". All
unused fields in a message MUST be transmitted as zeroes and ignored
by the receiver of the message.
8.1. DHCP Solicit Message Format
msg-type SOLICIT
transaction-ID An unsigned integer generated by the client used
to identify this Solicit message.
options See section 23.
8.2. DHCP Advertise Message Format
msg-type ADVERTISE
transaction-ID An unsigned integer used to identify this
Advertise message. Copied from the Solicit
message received from the client.
options See section 23.
8.3. DHCP Request Message Format
msg-type REQUEST
transaction-ID An unsigned integer generated by the client used
to identify this Request message.
options See section 23.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 12]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
8.4. DHCP Confirm Message Format
msg-type CONFIRM
transaction-ID An unsigned integer generated by the client used
to identify this Confirm message.
options See section 23.
8.5. DHCP Renew Message Format
msg-type RENEW
transaction-ID An unsigned integer generated by the client used
to identify this Renew message.
options See section 23.
8.6. DHCP Rebind Message Format
msg-type REBIND
transaction-ID An unsigned integer generated by the client used
to identify this Rebind message.
options See section 23.
8.7. DHCP Reply Message Format
msg-type REPLY
transaction-ID An unsigned integer used to identify this
Reply message. Copied from the client Request,
Confirm, Renew or Rebind message received from
the client.
options See section 23.
8.8. DHCP Release Message Format
msg-type RELEASE
transaction-ID An unsigned integer generated by the client used
to identify this Release message.
options See section 23.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 13]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
8.9. DHCP Decline Message Format
msg-type DECLINE
transaction-ID An unsigned integer generated by the client used
to identify this Decline message.
options See section 23.
8.10. DHCP Reconfigure Message Format
msg-type RECONFIG
transaction-ID An unsigned integer generated by the server used
to identify this Reconfigure message.
options See section 23.
8.11. Information-Request Message Format
msg-type INFORMATION-REQUEST
transaction-ID An unsigned integer generated by the client used
to identify this Information-request message.
options See section 23.
9. Relay messages
Relay agents exchange messages with servers to forward messages
between clients and servers that are not connected to the same link.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 14]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
There are two relay messages, which share the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type | |
+-+-+-+-+-+-+-+-+ |
| link-address |
| |
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-|
| | |
+-+-+-+-+-+-+-+-+ |
| client-return-address |
| |
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-|
| | |
+-+-+-+-+-+-+-+-+ |
. .
. options (variable number and length) .... .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The following sections describe the use of the Relay message header.
9.1. Relay-forward message
The following table defines the use of message fields in a
Relay-forward message.
msg-type RELAY-FORW
link-address An address with a prefix that is assigned
to the link from which the client should
be assigned an address.
client-return-address The IPv6 source address in which the
message from the client was received by
the relay agent
options MUST include a "Client message option";
see section 23.10; MAY include other
options added by the relay agent
Droms (ed.), et al. Expires 1 Aug 2002 [Page 15]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
9.2. Relay-reply message
The following table defines the use of message fields in a
Relay-reply message.
msg-type RELAY-REPL
link-address The link-address copied from the
Relay-forward message; used by the relay
agent to select the link on which the
message is returned to the client
client-return-address The source address from the IP datagram
in which the message from the client was
received by the relay agent
options MUST include a "Server message option";
see section 23.11; MAY include other
options
10. Representation and use of domain names
So that domain names may be encoded uniformly and compactly, a
domain name or a list of domain names is encoded using the technique
described in sections 3.1 and 4.1.4 of RFC1035 [14]. Section 4.1.4
of RFC1035 describes how more than one domain name can be represented
in a list of domain names. For use in this specification, in a
list of domain names, the compression pointer (see section 4.1.4 of
RFC1035) refers to the offset within the list.
If a single domain name is being used by a vendor as a vendor
identifier, then the vendor MUST ensure that the domain name has not
previously been used by a different vendor.
11. DHCP unique identifier (DUID)
Each DHCP client and server has a DUID. DHCP servers use DUIDs to
identify clients for the selection of configuration parameters and
in the association of IAs with clients. DHCP clients use DUIDs to
identify a server in messages where a server needs to be identified.
See sections 23.3 and 23.2 for the representation of a DUID in a DHCP
message.
Clients and servers MUST treat DUIDs as opaque values and MUST only
compare DUIDs for equality. Clients and servers MUST NOT in any
other way interpret DUIDs. Clients and servers MUST NOT restrict
DUIDs to the types defined in this document as additional DUID types
may be defined in the future.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 16]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The DUID is carried in an option because it may be variable length
and because it is not required in all DHCP options. The DUID is
designed to be unique across all DHCP clients and servers, and
consistent for any specific client or server - that is, the DUID used
by a client or server SHOULD NOT change over time, for example, as a
result of network hardware reconfiguration.
The motivation for having more than one type of DUID is that the DUID
must be globally unique, and must also be easy to generate. The sort
of globally-unique identifier that is easy to generate for any given
device can differ quite widely. Also, some devices may not contain
any persistent storage. Retaining a generated DUID in such a device
is not possible, so the DUID scheme must accommodate such devices.
11.1. DUID contents
A DUID consists of a sixteen-bit type code represented in network
order, followed by a variable number of octets that make up the
actual identifier. A DUID can be no more than 256 octets long. The
following types are currently defined:
1 Link-layer address plus time
2 Vendor-assigned unique ID
3 Link-layer address
Formats for the variable field of the DUID for each of the above
types are shown below.
11.2. DUID based on link-layer address plus time
This type of DUID consists of a two octet type field containing the
value 1, a two octet hardware type code, four octets containing
a time value, followed by link-layer address of any one network
interface that is connected to the DHCP device at the time that the
DUID is generated. The time value is the time that the DUID is
generated represented in seconds since midnight (UTC), January 1,
2000, modulo 2^32. The hardware type MUST be a valid hardware type
assigned by the IANA as described in the section on ARP in RFC 826.
Both the time and the hardware type are stored in network order.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 17]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The following diagram illustrates the format of a DUID based on
link-layer address plus time:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 1 | Hardware type (16 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Time (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. link-layer address (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The choice of network interface can be completely arbitrary, as long
as that interface provides a unique link-layer address, and the same
DUID should be used in configuring all network interfaces connected
to the device, regardless of which interface's link-layer address was
used to generate the DUID.
Clients and servers using this type of DUID MUST store the DUID
in stable storage, and MUST continue to use this DUID even if the
network interface used to generate the DUID is removed. Clients and
servers that do not have any stable storage MUST NOT use this type of
DUID.
Clients and servers that use this DUID SHOULD attempt to configure
the time prior to generating the DUID, if that is possible, and MUST
use some sort of time source (e.g., a real-time clock) in generating
the DUID, even if that time source could not be configured prior to
generating the DUID. The use of a time source makes it unlikely that
two identical DUIDs will be generated if the network interface is
removed from the client and another client then uses the same network
interface to generate a DUID. A DUID collision is very unlikely even
if the clocks haven't been configured prior to generating the DUID.
This method of DUID generation is recommended for all general purpose
computing devices such as desktop computers and laptop computers, and
also for devices such as printers, routers, and so on, that contain
some form of writable non-volatile storage.
11.3. Vendor-assigned unique ID (VUID)
The vendor-assigned unique ID consists of a two-octet value giving
the length of the identifier, the value of the idnetifier and the
vendor's registered domain name.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 18]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The following diagram summarizes the structure of a VUID:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 2 | identifier length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. identifier .
. (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. domain name (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The source of the identifier is left up to the vendor defining it,
but each identifier part of each VUID MUST be unique to the device
that is using it, and MUST be assigned to the device at the time of
manufacture and stored in some form of non-volatile storage. The
VUID SHOULD be recorded in non-erasable storage. The domain name
is simply any domain name that has been legally registered by the
vendor in the domain name system [13], stored in the form described
in section 10.
An example DUID of this type might look like this:
+---+---+---+---+---+---+---+---+
| 0 | 2 | 0 | 8 | 12|192|132|221|
+---+---+---+---+---+---+---+---+
| 3 | 0 | 9 | 18|101|120| 97|109|
+---+---+---+---+---+---+---+---+
|112|108|101| 46| 99|111|109|
+---+---+---+---+---+---+---+
This example includes the two-octet type of 2, the two-octet length
of 8, eight octets of identifier data, followed by "example.com"
represented in ASCII.
11.4. Link-layer address
This type of DUID consists of two octets containing the DUID type 3,
a two octet network hardware type code, followed by the link-layer
address of any one network interface that is permanently connected
to the client or server device and cannot be removed. The hardware
type MUST be a valid hardware type assigned by the IANA as described
in the section on ARP in RFC 826. The hardware type is stored in
network order.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 19]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The following diagram illustrates the format of a DUID based on
link-layer address:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 3 | Hardware type (16 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. link-layer address (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The choice of network interface can be completely arbitrary, as
long as that interface provides a unique link-layer address and
is permanently attached to the device on which the DUID is being
generated. The same DUID should be used in configuring all network
interfaces connected to the device, regardless of which interface's
link-layer address was used to generate the DUID.
This type of DUID is recommended for devices that have a
permanently-connected network interface with a link-layer address and
do not have nonvolatile, writable stable storage. This type of DUID
MUST NOT be used by DHCP clients or servers that cannot tell whether
or not a network interface is permanently attached to the device on
which the DHCP client is running.
12. Identity association
An "identity-association" (IA) is a construct through which a server
and a client can identify, group and manage IPv6 addresses. Each IA
consists of an IAID and associated configuration information.
A client must associate at least one distinct IA with each of
its network interfaces and uses that IA to obtain configuration
information from a server for that interface. Other distinct IAs may
be associated with applications. Each IA must be associated with
exactly one interface.
The IAID uniquely identifies the IA and must be chosen to be unique
among the IAIDs on the client. The IAID is chosen by the client.
For any given use of an IA by the client, the IAID for that IA MUST
be consistent across restarts of the DHCP client. The client may
maintain consistency either by storing the IAID in non-volatile
storage or by using an algorithm that will consistently produce the
same IAID as long as the configuration of the client has not changed.
There may be no way for a client to maintain consistency of the IAIDs
if it does not have non-volatile storage and the client's hardware
configuration changes.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 20]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The configuration information in an IA consists of one or more IPv6
addresses and other parameters. The parameters are specified as DHCP
options within the IA, and are associated with the addresses in the
IA and the interface to which the IA belongs. Other parameters that
are not associated with a particular interface may be specified in
the options section of a DHCP message, outside the scope of any IA.
Each address in an IA has a preferred lifetime and a valid lifetime,
as defined in RFC2462 [21]. The lifetimes are transmitted from the
DHCP server to the client in the IA option. The lifetimes apply to
the use of IPv6 addresses as described in section 5.5.4 of RFC2462.
An address whose valid lifetime has expired MAY be discarded from the
IA.
See section 23.4 for the representation of an IA in a DHCP message.
13. Selecting addresses for assignment to an IA
A server selects addresses to be assigned to an IA according to the
address assignment policies determined by the server administrator
and the specific information the server determines about the client
from the following sources:
- The link to which the client is attached. The server determines
the link as follows:
* If the server receives the message directly from the client
and the source address in the IP datagram in which the
message was received is a link-local address, then the client
is on the same link to which the interface over which the
message was received is attached
* If the server receives the message from a forwarding relay
agent, then the client is on the same link as the one to
which the interface identified by the link-address field in
the message from the relay is attached
- The DUID supplied by the client
- Other information in options supplied by the client
- Other information in options supplied by the relay agent
- If the server receives the message directly from the client and
the source address in the IP datagram in which the message was
received is not a link-local address, then the client is on the
link identified by the source address in the IP datagram (note
that this situation can occur only if the server has enabled the
use of unicast message delivery by the client and the client has
sent a message for which unicast delivery is allowed)
Droms (ed.), et al. Expires 1 Aug 2002 [Page 21]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The addresses that the server selects for the client MUST be valid on
the link to which the interface is attached, regardless of the way in
which the server selects the addresses.
14. Management of temporary addresses
A client may be assigned temporary addresses [16]. Clients and
servers simply label addresses as "temporary". DHCPv6 handling
of address lifetimes and lifetime extensions is no different for
temporary addresses. DHCPv6 says nothing about details of temporary
addresses like lifetimes, lifetime extensions, how clients use
temporary addresses, rules for generating successive temporary
addresses, etc.
In DHCP, temporary addresses are identified with T-bit set in the IA
Address Option(see section 23.5). A client may have zero or more
temporary addresses. Addresses with the T-bit set MUST be intended
for the client to use for the general purposes described in RFC3041.
Addresses that otherwise have short lifetimes or are not intended to
be renewed by the server MUST NOT have the T-bit set.
Clients ask for temporary addresses and servers assign them. When
a client sends an IA to a server, the client lists all of the
temporary addresses it knows about and optionally indicates how many
additional temporary addresses it wants in the Requested Temporary
Addresses Option(see section 23.6). The server compares the number
of requested additional temporary addresses against any previously
allocated temporary addresses for the IA that were not reported
by the client in the IA but still have some reasonable preferred
lifetime left. If the number of temporary addresses is less than the
requested number, the server adds additional temporary addresses to
the IA to satisfy the requested number (subject to server policy).
DISCUSSION:
It is important that the server include any allocated
temporary addresses that were not reported by the client as
it is possible the client never received an earlier Reply
that contained these additional temporary addresses. If
the server did not consider these, a client that fails to
receive a server's reply might cause the server to allocate
many temporary addresses.
When the valid lifetime on a temporary address expires, both the
client and server silently discard the address from the IA. The
discarded address no longer counts against the client's allotment of
temporary addresses.
A server SHOULD NOT assign a client temporary addresses without the
client having specifically asked for it. The client is not obligated
to install address(es) that it receives and did not request and can
release any addresses it does not want.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 22]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The server MAY update the DNS for a temporary address as described in
section 4 of RFC3041, and MUST NOT update the DNS in any other way
for a temporary address.
15. Reliability of Client Initiated Message Exchanges
DHCP clients are responsible for reliable delivery of messages in the
client-initiated message exchanges described in sections 18 and 19.
If a DHCP client fails to receive an expected response from a server,
the client must retransmit its message. This section describes the
retransmission strategy to be used by clients in client-initiated
message exchanges.
Note that the procedure described in this section is slightly
modified for use with the Solicit message (section 18.1.2).
The client begins the message exchange by transmitting a message to
the server. The message exchange terminates when either the client
successfully receives the appropriate response or responses from a
server or servers, or when the message exchange is considered to have
failed according to the retransmission mechanism described below.
The client retransmission behavior is controlled and described by the
following variables:
RT Retransmission timeout
IRT Initial retransmission time
MRC Maximum retransmission count
MRT Maximum retransmission time
MRD Maximum retransmission duration
RAND Randomization factor
With each message transmission or retransmission, the client sets RT
according to the rules given below. If RT expires before the message
exchange terminates, the client recomputes RT and retransmits the
message.
Each of the computations of a new RT include a randomization factor
(RAND), which is a random number chosen with a uniform distribution
between -0.1 and +0.1. The randomization factor is included to
minimize synchronization of messages transmitted by DHCP clients.
The algorithm for choosing a random number does not need to be
cryptographically sound. The algorithm SHOULD produce a different
sequence of numbers from each invocation of the DHCP client.
RT for the first message transmission is based on IRT:
Droms (ed.), et al. Expires 1 Aug 2002 [Page 23]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
RT = 2*IRT + RAND*IRT
RT for each subsequent message transmission is based on the previous
value of RT:
RT = 2*RTprev + RAND*RTprev
MRT specifies an upper bound on the value of RT. If MRT has a value
of 0, there is no upper limit on the value of RT. Otherwise:
if (RT > MRT)
RT = MRT + RAND*MRT
MRC specifies an upper bound on the number of times a client may
retransmit a message. If MRC has a value of 0, the client MUST
continue to retransmit the original message until a response is
received. Otherwise, the message exchange fails once the client has
transmitted the message MRC times.
MRD specifies an upper bound on the length of time a client may
retransmit a message. If MRD has a value of 0, the client MUST
continue to retransmit the original message until a response is
received. Otherwise, the message exchange fails once the client has
transmitted the message MRD seconds.
If both MRC and MRD are non-zero, the message exchange fails whenever
either of the conditions specified in the previous two paragraphs are
met.
16. Message validation
Servers MUST discard any received messages that include
authentication information and fail the authentication check by the
server.
Clients MUST discard any received messages that include
authentication information and fail the authentication check by the
client, except as noted in section 22.6.5.2.
16.1. Use of Transaction-ID field
The "transaction-ID" field holds a value used by clients and servers
to synchronize server responses to client messages. A client SHOULD
choose a different transaction-ID for each new message it sends. A
client MUST leave the transaction-ID unchanged in retransmissions of
a message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 24]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
16.2. Solicit message
Clients MUST discard any received Solicit messages.
Relay agents MUST discard any Solicit messages received through port
546.
Servers MUST discard any Solicit messages that do not include a
Client Identifier option.
16.3. Advertise message
Clients MUST discard any received Advertise messages that meet any of
the following conditions:
- the message does not include a Server Identifier option
- the message does not include a Client Identifier option
- the contents of the Client Identifier option does not match the
client's DUID
- the "Transaction-ID" field value does not match the value the
client used in its Solicit message
Servers and relay agents MUST discard any received Advertise
messages.
16.4. Request message
Clients MUST discard any received Request messages.
Relay agents MUST discard any Request messages received through port
546.
Servers MUST discard any received Request message that meet any of
the following conditions:
- the message does not include a Server Identifier option
- the contents of the Server Identifier option do not match the
server's identifier
- the message does not include a Client Identifier option
16.5. Confirm message
Clients MUST discard any received Confirm messages.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 25]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Relay agents MUST discard any Confirm messages received through port
546.
Servers MUST discard any Confirm messages received that do not
include a Client Identifier option.
16.6. Renew message
Clients MUST discard any received Renew messages.
Relay agents MUST discard any Renew messages received through port
546.
Servers MUST discard any received Renew message that meets any of the
following conditions:
- the message does not include a Server Identifier option
- the contents of the Server Identifier option do not match the
server's identifier
- the message does not include a Client Identifier option
16.7. Rebind message
Clients MUST discard any received Rebind messages.
Relay agents MUST discard any Rebind messages received through port
546.
Servers MUST discard any received Rebind message that does not
include a Client Identifier option.
16.8. Decline messages
Clients MUST discard any received Decline messages.
Relay agents MUST discard any Decline messages received through port
546.
Servers MUST discard any received Decline message that meets any of
the following conditions:
- the message does not include a Server Identifier option
- the contents of the Server Identifier option do not match the
server's identifier
- the message does not include a Client Identifier option
Droms (ed.), et al. Expires 1 Aug 2002 [Page 26]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
16.9. Release message
Clients MUST discard any received Release messages.
Relay agents MUST discard any Release messages received through port
546.
- the message does not include a Server Identifier option
- the contents of the Server Identifier option do not match the
server's identifier
- the message does not include a Client Identifier option
16.10. Reply message
Clients MUST discard any received Reply messages that meet any of the
following conditions:
- the message does not include a Server Identifier option
- the "transaction-ID" field in the message does not match the
value used in the original message
- the message does not include a Client Identifier option
- the contents of the Client Identifier option does not match the
DUID of the client
Servers and relay agents MUST discard any received Reply messages.
16.11. Reconfigure message
Servers and relay agents MUST discard any received Reconfigure
messages.
Clients MUST discard any Reconfigure messages that meet any of the
following conditions:
- the message does not include a Server Identifier option
- the message does not contain an authentication option
- the message fails the authentication validation performed by the
client
16.12. Information-request message
Clients MUST discard any received Information-request messages.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 27]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Relay agents MUST discard any Information-request messages received
through port 546.
Servers MAY choose to discard any received Information-request
messages that do not include a Client Identifier option.
Servers MUST discard any received Information-request message that
includes a Server Identifier option and the DUID in the option does
not match the server's DUID.
16.13. Relay-forward message
Clients MUST discard any received Relay-forward messages.
16.14. Relay-reply message
Clients and servers MUST discard any received Relay-reply messages.
17. Client Source Address and Interface Selection
When a client sends a DHCP message to the All_DHCP_Agents multicast
address, it MUST use the IPv6 link-local address assigned to
the interface for which the client is interested in obtaining
configuration as the source address in the header of the IP datagram.
When a client sends a DHCP message directly to a server using unicast
(after receiving the Server Unicast option from that server), it
MUST use an address assigned to the interafce for which the client
is interested in obtaining configuration, which is suitable for use
by the server in responding to the client, as the source address in
the header of the IP datagram. See "Default Address Selection for
IPv6" [6] for more details.
The client MUST transmit the message on the link that the interface
for which configuration information is being obtained is attached
to. The client SHOULD send the message through that interface. The
client MAY send the message through another interface attached to the
same link if and only if the client is certain the two interface are
attached to the same link.
18. DHCP Server Solicitation
This section describes how a client locates servers that will assign
addresses to IAs belonging to the client.
The client is responsible for creating IAs and requesting that a
server assign configuration information, including IPv6 addresses,
to the IA. The client first creates an IA and assigns it an IAID.
The client then transmits a Solicit message containing an IA option
Droms (ed.), et al. Expires 1 Aug 2002 [Page 28]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
describing the IA. Servers that can assign configuration information
to the IA respond to the client with an Advertise message. The
client then initiates a configuration exchange as described in
section 19.
18.1. Client Behavior
A client uses the Solicit message to discover DHCP servers configured
to serve addresses on the link to which the client is attached.
18.1.1. Creation of Solicit messages
The client sets the "msg-type" field to SOLICIT. The client generates
a transaction ID and inserts this value in the "transaction-ID"
field.
The client MUST include a Client Identifier option to identify itself
to the server. The client MUST include one or more IA options for
any IAs to which it wants the server to assign addresses. The client
MAY include addresses in the IAs as a hint to the server about
addresses for which the client has a preference. The client MAY
include an Option Request Option in the Solicit message. The client
MUST NOT include any other options except those specifically allowed
as defined by specific options.
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned.
18.1.2. Transmission of Solicit Messages
The client sends the Solicit message to the All_DHCP_Agents multicast
address.
The first Solicit message from the client on the interface MUST
be delayed by a random amount of time between MIN_SOL_DELAY and
MAX_SOL_DELAY. This random delay desynchronizes clients which start
at the same time (e.g., after a power outage).
Droms (ed.), et al. Expires 1 Aug 2002 [Page 29]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The client transmits the message according to section 15, using the
following parameters:
IRT SOL_TIMEOUT
MRT SOL_MAX_RT
MRC 0
MRD 0
The mechanism in section 15 is modified as follows for use in the
transmission of Solicit messages. The message exchange is not
terminated by the receipt of an Advertise before IRT has elapsed.
Rather, the client collects Advertise messages until IRT has elapsed.
Also, the first RT MUST be selected to be strictly greater than IRT
by choosing RAND to be strictly greater than 0.
A client MUST collect Advertise messages for IRT seconds, unless
it receives an Advertise message with a preference value of 255.
The preference value is carried in the Preference option (section
23.8). Any Solicit that does not include a Preference option is
considered to have a preference value of 0. If the client receives
an Advertise message with a preference value of 255, then the client
MAY act immediately on that Advertise message without waiting for any
additional Advertise messages.
If the client does not receive any Advertise messages before IRT
has elapsed, it begins the retransmission mechanism described in
section 15. The client terminates the retransmission process as
soon as it recieves any Advertise message, and the client acts on
the received Advertise message without waiting for any additional
Advertise messages.
A DHCP client SHOULD choose MRC and MRD to be 0. If the DHCP client
is configured with either MRC or MRD set to a value other than
0, it MUST stop trying to configure the interface if the message
exchange fails. After the DHCP client stops trying to configure the
interface, it SHOULD choose to restart the reconfiguration process
after some external event, such as user input, system restart, or
when the client is attached to a new link.
18.1.3. Receipt of Advertise messages
The client MUST ignore any Advertise message that includes a Status
Code option containing the value AddrUnavail, with the exception that
the client MAY display the associated status message to the user.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 30]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Upon receipt of one or more valid Advertise messages, the client
selects one or more Advertise messages based upon the following
criteria.
- Those Advertise messages with the highest server preference value
are preferred over all other Advertise messages.
- Within a group of Advertise messages with the same server
preference value, a client MAY select those servers whose
Advertise messages advertise information of interest to the
client. For example, the client may choose a server that
returned an advertisement with configuration options of interest
to the client.
- The client MAY choose a less-preferred server if that server has
a better set of advertised parameters, such as the available
addresses advertised in IAs.
Once a client has selected Advertise message(s), the client will
typically store information about each server, such as server
preference value, addresses advertised, when the advertisement was
received, and so on. Depending on the requirements of the user that
invoked the DHCP client, the client MAY initiate a configuration
exchange with the server(s) immediately, or MAY defer this exchange
until later.
If the client needs to select an alternate server in the case that a
chosen server does not respond, the client chooses the next server
according to the criteria given above.
18.2. Server Behavior
A server sends an Advertise message in response to Solicit messages
it receives to announce the availability of the server to the client.
18.2.1. Receipt of Solicit messages
The server determines the information about the client and its
location as described in section 13. If administrative policy
permits the server to respond to the client, the server will generate
and send an Advertise message to the client.
18.2.2. Creation and transmission of Advertise messages
The server sets the "msg-type" field to ADVERTISE and copies the
contents of the transaction-ID field from the Solicit message
received from the client to the Advertise message. The server
includes its server identifier in a Server Identifier option.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 31]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The server MAY add a Preference option to carry the preference value
for the Advertise message. The server implementation SHOULD allow
the setting of a server preference value by the administrator.
The server preference value MUST default to zero unless otherwise
configured by the server administrator.
The server MUST include IA options in the Advertise message
containing any addresses that would be assigned to IAs contained in
the Solicit message from the client. The server MAY include some or
all of the IA options from the client in the Advertise message.
If the server will not assign any addresses to IAs in a subsequent
Request from the client, the server SHOULD either send an Advertise
message to the client that includes only a status code option with
the status code set to AddrUnavail and a status message for the user
or not respond to the Solicit message.
The server may choose to assign fewer temporary addresses than
the client requested with an RTA option (see section 23.6) and
includes a status code of Success in the IA. If the server will
assign no temporary addresses, the server includes a status code of
AddrUnavail.
The server MAY include other options the server will return to the
client in a subsequent Reply message. The information in these
options will be used by the client in the selection of a server if
the client receives more than one Advertise message. The server
SHOULD include options specifying values for options requested by the
client in an Option Request Option included in the Solicit message.
If the Solicit message was received directly by the server, the
server unicasts the Advertise message directly to the client using
the address in the source address field from the IP datagram in
which the Solicit message was received. The Advertise message MUST
be unicast through the interface on which the Solicit message was
received.
If the Solicit message was received in a Relay-forward message,
the server constructs a Relay-reply message with the Advertise
message in the payload of a "server-message" option. The server
unicasts the Relay-reply message directly to the relay agent using
the address in the source address field from the IP datagram in which
the Relay-forward message was received.
19. DHCP Client-Initiated Configuration Exchange
A client initiates a message exchange with a server or servers to
acquire or update configuration information of interest. The client
may initiate the configuration exchange as part of the operating
system configuration process or when requested to do so by the
application layer.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 32]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
19.1. Client Behavior
A client will use Request, Confirm, Renew, Rebind and
Information-request messages to acquire and confirm the
validity of configuration information. The client uses the server
identifier information and information about IAs from previous
Advertise messages for use in constructing Request messages. Note
that a client may request configuration information from one or more
servers at any time.
19.1.1. Creation and transmission of Request messages
The client uses a Request message to populate IAs with addresses
and obtain other configuration information. The client includes
one or more IA options in the Request message, with addresses and
information about the IAs that were obtained from the server in a
previous Advertise message. The server then returns addresses and
other information about the IAs to the client in IA options in a
Reply message.
The client generates a transaction ID and inserts this value in the
"transaction-ID" field.
The client places the identifier of the destination server in a
Server Identifier option.
The client MUST include a Client Identifier option to identify itself
to the server. The client adds any other appropriate options,
including one or more IA options (if the client is requesting that
the server assign it some network addresses). The list of addresses
in each included IA MUST include the addresses received by the client
in a previous Advertise message.
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned.
If the client has a source address of sufficient scope that can be
used by the server as a return address and the client has received
a Server Unicast option (section 23.13) from the server, the client
SHOULD unicast the Request message to the server. Otherwise, the
client MUST send the Request message to the All_DHCP_Agents multicast
address.
DISCUSSION:
Use of multicast and relay agents enables the inclusion of
relay agent options in all messages sent by the client. The
server should enable the use of unicast only when relay
agent options will not be used.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 33]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The client transmits the message according to section 15, using the
following parameters:
IRT REQ_TIMEOUT
MRT REQ_MAX_RT
MRC REQ_MAX_RC
MRD 0
If the message exchange fails, the client MAY choose one of the
following actions:
- Select another server from a list of servers known to the client;
e. g., servers that responded with an Advertise message
- Initiate the server discovery process described in section 18
- Terminate the configuration process and report failure
19.1.2. Creation and transmission of Confirm messages
Whenever a client may have moved to a new link, its IPv6 addresses
and other configuration information may no longer be valid. Examples
of times when a client may have moved to a new link include:
o The client reboots
o The client is physically disconnected from a wired connection
o The client returns from sleep mode
o The client using a wireless technology changes access points
In any situation when a client may have moved to a new link, the
client MUST initiate a Confirm/Reply message exchange. The client
includes any IAs, along with the addresses associated with those IAs,
in its Confirm message. Any responding servers will indicate the
acceptability of the addresses with the status in the Reply message
it returns to the client.
The client sets the "msg-type" field to CONFIRM. The client generates
a transaction ID and inserts this value in the "transaction-ID"
field.
The client MUST include a Client Identifier option to identify itself
to the server. The client adds any appropriate options, including
one or more IA options. The client MUST include the addresses the
client currently has associated with those IAs.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 34]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned.
The client sends the Confirm message to the All_DHCP_Agents multicast
address. The client MUST use an IPv6 address that the client has
confirmed to be valid on the link to which it is currently attached
and that is assigned to the interface for which the client is
interested in obtaining configuration information as the source
address in the IP header of the datagram carrying the Confirm
message.
The client transmits the message according to section 15, using the
following parameters:
IRT CNF_TIMEOUT
MRT CNF_MAX_RT
MRC 0
MRD CNF_MAX_RD
If the client receives no responses before the message transmission
process as described in section 15 terminates, the client SHOULD
continue to use any IP addresses, using the last known lifetimes for
those addresses, and SHOULD continue to use any other previously
obtained configuration parameters.
19.1.3. Creation and transmission of Renew messages
To extend the valid and preferred lifetimes associated with
addresses, the client sends a Renew message to the server containing
an "IA option" for the IA and its associated addresses. The server
determines new lifetimes for the addresses in the IA according to the
administrative configuration of the server. The server may also add
new addresses to the IA. The server may remove addresses from the IA
by setting the preferred and valid lifetimes of those addresses to
zero.
The server controls the time at which the client contacts the server
to extend the lifetimes on assigned addresses through the T1 and T2
parameters assigned to an IA.
At time T1 for an IA, the client initiates a Renew/Reply message
exchange to extend the lifetimes on any addresses in the IA. The
client includes an IA option with all addresses currently assigned to
the IA in its Renew message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 35]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The client sets the "msg-type" field to RENEW. The client generates a
transaction ID and inserts this value in the "transaction-ID" field.
The client places the identifier of the destination server in a
Server Identifier option.
The client MUST include a Client Identifier option to identify
itself to the server. The client adds any appropriate options,
including one or more IA options (if the client is requesting that
the server extend the lifetimes of the addresses assigned to those
IAs; note that the client may check the status of other configuration
parameters without asking for lifetime extensions). The client MUST
include the list of addresses the client currently has associated
with the IAs in the Renew message.
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned.
If the client has a source address of sufficient scope that can be
used by the server as a return address and the client has received
a Server Unicast option (section 23.13) from the server, the client
SHOULD unicast the Renew message to the server. Otherwise, the
client sends the Renew message to the All_DHCP_Agents multicast
address.
DISCUSSION:
Use of multicast and relay agents enables the inclusion of
relay agent options in all messages sent by the client. The
server MUST NOT enable the use of unicast for a client when
relay agent options are required for that client.
The client transmits the message according to section 15, using the
following parameters:
IRT REN_TIMEOUT
MRT REP_MAX_RT
MRC 0
MRD 0
The mechanism in section 15 is modified as follows for use in the
transmission of Renew messages. The message exchange is terminated
when time T2 is reached (see section 19.1.4), at which time the
client begins a Rebind message exchange.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 36]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
19.1.4. Creation and transmission of Rebind messages
At time T2 for an IA (which will only be reached if the server to
which the Renew message was sent at time T1 has not responded),
the client initiates a Rebind/Reply message exchange. The client
includes an IA option with all addresses currently assigned to the
IA in its Rebind message. The client sends this message to the
All_DHCP_Agents multicast address.
The client sets the "msg-type" field to REBIND. The client generates
a transaction ID and inserts this value in the "transaction-ID"
field.
The client MUST include a Client Identifier option to identify
itself to the server. The client adds any appropriate options,
including one or more IA options. The client MUST include the list
of addresses the client currently has associated with the IAs in the
Rebind message.
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned.
The client sends the Rebind message to the All_DHCP_Agents multicast
address.
The client transmits the message according to section 15, using the
following parameters:
IRT REB_TIMEOUT
MRT REB_MAX_RT
MRC 0
MRD 0
The mechanism in section 15 is modified as follows for use in the
transmission of Rebind messages. The message exchange is terminated
when the lifetimes of all of the addresses assigned to the IA expire
(see section 12), at which time the client has several alternative
actions to choose from:
- The client may choose to use a Solicit message to locate a new
DHCP server and send a Request for the expired IA to the new
server
- The client may have other addresses in other IAs, so the client
may choose to discard the expired IA and use the addresses in the
other IAs
Droms (ed.), et al. Expires 1 Aug 2002 [Page 37]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
19.1.5. Creation and Transmission of Information-request messages
The client uses an Information-request message to obtain
configuration information without having addresses assigned to it.
The client sets the "msg-type" field to INFORMATION-REQUEST. The
client generates a transaction ID and inserts this value in the
"transaction-ID" field.
The client SHOULD include a Client Identifier option to identify
itself to the server. If the client does not include a Client
Identifier option, the server will not be able to return any
client-specific options to the client.
If the client chooses to request specific options from the server,
it does so by including an Option Request option (see section 23.7,
which MUST include all of the options the client is requesting. The
client MAY include options with data values as hints to the server
about parameter values the client would like to have returned. The
client MUST NOT include any IA options.
If the client has an IPv6 address of sufficient scope, the
client MAY choose to send the Information-request message to the
All_DHCP_Servers multicast address. Otherwise, the client MUST send
the Information-request message to the All_DHCP_Agents multicast
address.
The client transmits the message according to section 15, using the
following parameters:
IRT INF_TIMEOUT
MRT INF_MAX_RT
MRC 0
MRD 0
19.1.6. Receipt of Reply message in response to a Request, Confirm,
Renew, Rebind or Information-request message
Upon the receipt of a valid Reply message in response to a Request,
Confirm, Renew, Rebind or Information-request message, the client
extracts the configuration information contained in the Reply. The
client MAY choose to report any status code or message from the
status code option in the Reply message.
The client SHOULD perform duplicate address detection [21] on each
of the addresses in any IAs it receives in the Reply message after
a Request message. If any of the addresses are found to be in use
on the link, the client sends a Decline message to the server as
described in section 19.1.9.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 38]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The client records the T1 and T2 times for each IA in the Reply
message. The client records any addresses included with IAs in
the Reply message. The client updates the preferred and valid
lifetimes for the addresses in the IA from the lifetime information
in the IA option. The client leaves any addresses that the client
has associated with the IA that are not included in the IA option
unchanged.
The client SHOULD respond to the server with a Release message for
any addresses in the Reply message that have a valid lifetime of 0.
The client constructs and transmits this message as described in
section 19.1.7.
If the Reply was received in response to a Renew or Rebind message,
the client must update the information in any IA option contained in
the Reply message. The client adds any new addresses from the IA
option to the IA, updates lifetimes for existing addresses in the IA
from the IA option and discards any addresses with a lifetime of zero
in the IA option.
Management of the specific configuration information is detailed in
the definition of each option, in section 23.
When the client receives a NoPrefixMatch status in an IA from the
server the client can assume it needs to send a Request to the server
to obtain appropriate addresses for the IA. If the client receives
any Reply messages that do not indicate a NoPrefixMatch status, the
client can use the addresses in the IA and ignore any messages that
do indicate a NoPrefixMatch status.
When the client receives an AddrUnavail status in an IA from the
server for a Request message the client will have to find a new
server to create an IA.
When the client receives a NoBinding status in an IA from the server
for a Confirm message the client can assume it needs to send a
Request to reestablish an IA with the server.
When the client receives a ConfNoMatch status in an IA from the
server for a Confirm message the client can send a Renew message to
the server to extend the lifetimes of the addresses.
When the client receives a NoBinding status in an IA from the server
for a Renew message the client can assume it needs to send a Request
to reestablish an IA with the server.
When the client receives a RenwNoMatch status in an IA from the
server for a Renew message the client can assume it needs to send a
Request to reestablish an IA with the server.
When the client receives an AddrUnavail status in an IA from the
server for a Renew message the client can assume it needs to send a
Request to reestablish an IA with the server.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 39]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
When the client receives a NoBinding status in an IA from the server
for a Rebind message the client can assume it needs to send a Request
to reestablish an IA with the server or try another server.
When the client receives a RebdNoMatch status in an IA from the
server for a Rebind message the client can assume it needs to send a
Request to reestablish an IA with the server or try another server.
When the client receives an AddrUnavail status in an IA from the
server for a Rebind message the client can assume it needs to send a
Request to reestablish an IA with the server or try another server.
19.1.7. Creation and transmission of Release messages
The client sets the "msg-type" field to RELEASE. The client generates
a transaction ID and places this value in the "transaction-ID" field.
The client places the identifier of the server that allocated the
address(es) a Server Identifier option.
The client MUST include a Client Identifier option to identify itself
to the server. The client includes options containing the IAs it
is releasing in the "options" field. The addresses to be released
MUST be included in the IAs. The client continues to use any other
addresses in the IAs. The appropriate "status" field in the options
MUST be set to indicate the reason for the release.
The client MUST NOT use any of the addresses in the IAs in the
message as the source address in the Release message or in any
subsequently transmitted message.
If the client has a source address of sufficient scope that can be
used by the server as a return address and the client has received
a Server Unicast option (section 23.13) from the server, the client
SHOULD unicast the Release message to the server. Otherwise, the
client MUST send the Release message to the All_DHCP_Agents multicast
address.
DISCUSSION:
Use of multicast and relay agents enables the inclusion of
relay agent options in all messages sent by the client. The
server MUST NOT enable the use of unicast for a client when
relay agent options are required for that client.
A client MAY choose to wait for a Reply message from the server in
response to the Release message. If the client does wait for a
Reply, the client MAY choose to retransmit the Release message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 40]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The client transmits the message according to section 15, using the
following parameters:
IRT REL_TIMEOUT
MRT 0
MRC REL_MAX_MRC
MRD 0
The client MUST abandon the attempt to release addresses if the
Release message exchange fails.
The client MUST stop using all of the addresses in the IA(s) being
released as soon as the client begins the Release message exchange
process. If an IA is released but the Reply from a DHCP server
is lost, the client will retransmit the Release message, and the
server may respond with a Reply indicating a status of "Nobinding".
Therefore, the client does not treat a Reply message with a status
of "Nobinding" in a Release message exchange as if it indicates an
error.
Note that if the client fails to release the IA, the addresses
assigned to the IA will be reclaimed by the server when the lifetime
of the address expires.
19.1.8. Receipt of Reply message in response to a Release message
Upon receipt of a valid Reply message, the client can consider the
Release event successful.
19.1.9. Creation and transmission of Decline messages
The client sets the "msg-type" field to DECLINE. The client generates
a transaction ID and places this value in the "transaction-ID" field.
The client places the identifier of the server that allocated the
address(es) in a Server Identifier option.
The client MUST include a Client Identifier option to identify itself
to the server. The client includes options containing the IAs it is
declining in the "options" field. The addresses to be declined MUST
be included in the IAs. The client continues to use other addresses
in the IAs. The appropriate "status" field in the options MUST be
set to indicate the reason for declining the address.
The client MUST NOT use any of the addresses in the IAs in the
message as the source address in the Decline message or in any
subsequently transmitted message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 41]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
If the client has a source address of sufficient scope that can be
used by the server as a return address and the client has received
a Server Unicast option (section 23.13) from the server, the client
SHOULD unicast the Decline message to the server. Otherwise, the
client MUST send the Decline message to the All_DHCP_Agents multicast
address.
DISCUSSION:
Use of multicast and relay agents enables the inclusion of
relay agent options in all messages sent by the client. The
server MUST NOT enable the use of unicast for a client when
relay agent options are required for that client.
The client transmits the message according to section 15, using the
following parameters:
IRT DEC_TIMEOUT
MRT DEC_MAX_RT
MRC DEC_MAX_RC
MRD 0
The client MUST abandon the attempt to decline addresses if the
Decline message exchange fails.
19.1.10. Receipt of Reply message in response to a Decline message
Upon receipt of a valid Reply message, the client can consider the
Decline event successful.
19.2. Server Behavior
For this discussion, the Server is assumed to have been configured in
an implementation specific manner with configuration of interest to
clients.
19.2.1. Receipt of Request messages
The server MAY choose to discard Request messages received via
unicast from a client to which the server has not sent a unicast
option.
When the server receives a Request the client is requesting the
configuration of a new IA by the server. The server MUST take the
IA from the client and associate a binding for that client in an
implementation-specific manner within the configuration parameter
database for DHCP clients managed by the server.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 42]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Upon the receipt of a valid Request message from a client the server
can respond to, (implementation-specific administrative policy
satisfied) the server scans the options field.
The server then constructs a Reply message and sends it to the
client.
The server SHOULD process each option for the client in an
implementation-specific manner. The server MUST construct a Reply
message containing the following values:
msg-type REPLY
transaction-ID The transaction-ID from the Request message.
The server MUST include a Server Identifier option containing the
server's DUID in the Reply message.
If the server finds that the prefix on one or more IP addresses in
any IA in the message from the client is not a valid prefix for the
link to which the client is connected, the server MUST return the IA
to the client with the status field set to NoPrefixMatch.
If the server cannot assign any addresses to any of the IAs in
the message from the client, the server SHOULD include the IAs in
the Reply message with the status field set to AddrUnavail and no
addresses in the IA.
For any IAs to which the server can assign addresses, server includes
the IA with addresses and other configuration parameters a status of
Success, and add the IA as a new client binding.
The server may choose to assign fewer temporary addresses than
the client requested with an RTA option (see section 23.6) and
includes a status code of Success in the IA. If the server chooses to
assign no temporary addresses, the server includes a status code of
AddrUnavail.
The server adds options to the Reply message for any other
configuration information to be assigned to the client.
19.2.2. Receipt of Confirm messages
When the server receives a Confirm message, the client is requesting
confirmation that the configuration information it will use is valid.
The server SHOULD locate the binding for that client and compare the
information in the Confirm message from the client to the information
associated with that client.
Upon the receipt of a valid Confirm message from a client the server
can respond to, (implementation-specific administrative policy
satisfied) the server scans the options field.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 43]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
If the server cannot determine if the information in the Confirm
message is valid or invalid, the server MUST NOT send a reply to the
client. For example, if the server does not have a binding for the
client, but the configuration information in the Confirm message
appears valid, the server does not reply.
If the server finds that the information for the client does not
match what is in the binding for that client or the configuration
information is not valid, the server sends a Reply message containing
a Status Code option with the value ConfNoMatch.
If the server finds that the information for the client does match
the information in the binding for that client, and the configuration
information is still valid, the server sends a Reply message
containing a Status Code option with the value Success.
The server SHOULD process each option for the client in an
implementation-specific manner. The server MUST construct a Reply
message containing the following values:
msg-type REPLY
transaction-ID The transaction-ID from the Confirm message.
The server MUST include a Server Identifier option containing the
server's DUID in the Reply message.
The Reply message from the server MUST contain a Status Code option
and MUST NOT include any other options.
19.2.3. Receipt of Renew messages
The server MAY choose to discard Renew messages received via unicast
from a client to which the server has not sent a unicast option.
Upon the receipt of a valid Renew message from a client the server
can respond to, (implementation-specific administrative policy
satisfied) the server scans the options field.
When the server receives a Renew and IA option from a client it
SHOULD locate the clients binding and verify the information in the
IA from the client matches the information stored for that client.
If the server cannot find a client entry for this IA the server
SHOULD return an IA containing no addresses with status set to
NoBinding.
If the server finds that the addresses in the IA for the client
do not match the client binding the server should return an IA
containing no addresses with status set to RenwNoMatch.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 44]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
If the server cannot Renew addresses for the client it SHOULD send
back an IA containing no addresses to the client with the status
field set to AddrUnavail.
If the server finds the addresses in the IA for the client then the
server SHOULD send back the IA to the client with new lifetimes and
T1/T2 times if the default is not being used, and set status to
Success. The server may choose to change the list of addresses and
the lifetimes of addresses in IAs that are returned to the client.
The server may choose to assign fewer temporary addresses than
the client requested with an RTA option (see section 23.6) and
includes a status code of Success in the IA. If the server chooses to
assign no temporary addresses, the server includes a status code of
AddrUnavail.
The server SHOULD process each option for the client in an
implementation-specific manner. The server MUST construct a Reply
message containing the following values:
msg-type REPLY
transaction-ID The transaction-ID from the Confirm message.
The server MUST include a Server Identifier option containing the
server's DUID in the Reply message.
19.2.4. Receipt of Rebind messages
Upon the receipt of a valid Rebind message from a client the server
can respond to, (implementation-specific administrative policy
satisfied) the server scans the options field.
When the server receives a Rebind and IA option from a client it
SHOULD locate the clients binding and verify the information in the
IA from the client matches the information stored for that client.
If the server cannot find a client entry for this IA the server
SHOULD return an IA containing no addresses with status set to
NoBinding.
If the server finds that the addresses in the IA for the client
do not match the client binding the server should return an IA
containing no addresses with status set to RebdNoMatch.
If the server cannot Rebind addresses for the client it SHOULD send
back an IA containing no addresses to the client with the status
field set to AddrUnavail.
If the server finds the addresses in the IA for the client then the
server SHOULD send back the IA to the client with new lifetimes and
Droms (ed.), et al. Expires 1 Aug 2002 [Page 45]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
T1/T2 times if the default is not being used, and set status to
Success.
The server may choose to assign fewer temporary addresses than
the client requested with an RTA option (see section 23.6) and
includes a status code of Success in the IA. If the server will
assign no temporary addresses, the server includes a status code of
AddrUnavail.
The server SHOULD process each option for the client in an
implementation-specific manner. The server MUST construct a Reply
message containing the following values:
msg-type REPLY
transaction-ID The transaction-ID from the Confirm message.
The server MUST include a Server Identifier option containing the
server's DUID in the Reply message.
19.2.5. Receipt of Information-request messages
When the server receives an Information-request message, the client
is requesting configuration information that does not include
the assignment of any addresses. The server SHOULD determine all
configuration parameters appropriate to the client, based on the
server configuration policies known to the server.
Upon the receipt of a valid Information-request message from a client
the server can respond to, (implementation-specific administrative
policy satisfied) the server scans the options field. The server
then constructs a Reply message and sends it to the client.
The server SHOULD process each option for the client in an
implementation-specific manner. The server MUST construct a Reply
message containing the following values:
msg-type REPLY
transaction-ID The transaction-ID from the Confirm message.
The server MUST include a Server Identifier option containing the
server's DUID in the Reply message.
The server adds options to the Reply message for all of the
configuration parameters to be returned to the client.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 46]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
19.2.6. Receipt of Release messages
The server MAY choose to discard Release messages received via
unicast from a client to which the server has not sent a unicast
option.
Upon the receipt of a valid Release message, the server examines the
IAs and the addresses in the IAs for validity. If the IAs in the
message are in a binding for the client and the addresses in the IAs
have been assigned by the server to those IAs, the server deletes
the addresses from the IAs and makes the addresses available for
assignment to other clients. The server ignores invalid addresses
(though it may choose to log an error if it finds an invalid
address).
After all the addresses have been processed, the server generates a
Reply message and includes a Status Code option with value Success
and a Server Identifier option with the server's DUID. The server
MUST NOT include any other options in the Reply message.
A server is not required to (but may choose to as an implementation
strategy) retain any record of an IA from which all of the addresses
have been released.
19.2.7. Receipt of Decline messages
The server MAY choose to discard Decline messages received via
unicast from a client to which the server has not sent a unicast
option.
Upon the receipt of a valid Decline message, the server examines the
IAs and the addresses in the IAs for validity. If the IAs in the
message are in a binding for the client and the addresses in the IAs
have been assigned by the server to those IA, the server deletes
the addresses from the IAs. The server SHOULD mark the addresses
declined by the client so that those addresses are not assigned to
other clients, and MAY choose to make a notification that addresses
were declined. The server ignores invalid addresses (though it may
choose to log an error if it finds an invalid address).
After all the address have been processed, the server generates a
Reply message and includes a Status Code option with value Success
and a Server Identifier option with the server' DUID. The server MUST
NOT include any other options in the Reply message.
19.2.8. Transmission of Reply messages
If the Request, Confirm, Renew, Rebind, Release, Decline or
Information-request message from the client was originally received
in a Relay-forward message from a relay, the server places the
Reply message in the options field of a Relay-response message and
Droms (ed.), et al. Expires 1 Aug 2002 [Page 47]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
copies the link-address and client-return-address fields from the
Relay-forward message into the Relay-response message.
The server then unicasts the Reply or Relay-reply to the source
address from the IP datagram in which the original message was
received.
20. DHCP Server-Initiated Configuration Exchange
A server initiates a configuration exchange to cause DHCP clients
to obtain new addresses and other configuration information. For
example, an administrator may use a server-initiated configuration
exchange when links in the DHCP domain are to be renumbered. Other
examples include changes in the location of directory servers,
addition of new services such as printing, and availability of new
software (system or application).
20.1. Server Behavior
A server sends a Reconfigure message to cause a client to initiate
immediately a Renew/Reply or Information-request/Reply message
exchange with the server.
20.1.1. Creation and transmission of Reconfigure messages
The server sets the "msg-type" field to RECONFIGURE. The server
generates a transaction-ID and inserts it in the "transaction-ID"
field. The server places its identifier in a Server Identifier
option.
The server MAY include an Option Request option to inform the client
of what information has been changed or new information that has been
added. In particular, the server specifies the IA option in the
Option Request option if the server wants the client to obtain new
address information.
The server MUST include an authentication option with the appropriate
settings and add that option as the last option in the "options"
field of the Reconfigure message.
The server MUST NOT include any other options in the Reconfigure
except as specifically allowed in the definition of individual
options.
A server sends each Reconfigure message to a single DHCP client,
using an IPv6 unicast address of sufficient scope belonging to the
DHCP client. The server may obtain the address of the client through
the information that the server has about clients that have been in
contact with the server, or the server may be configured with the
address of the client through some external agent.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 48]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
To reconfigure more than one client, the server unicasts a separate
message to each client. The server may initiate the reconfiguration
of multiple clients concurrently; for example, a server may
send a Reconfigure message to additional clients while previous
reconfiguration message exchanges are still in progress.
The Reconfigure message causes the client to initiate a Renew/Reply
or Information-request/Reply message exchange with the server. The
server interprets the receipt of a Renew or Information-request
message from the client as satisfying the Reconfigure message
request.
20.1.2. Time out and retransmission of Reconfigure messages
If the server does not receive a Renew or Information-request message
from the client in RECREP_MSG_TIMEOUT milliseconds, the server
retransmits the Reconfigure message, doubles the RECREP_MSG_TIMEOUT
value and waits again. The server continues this process until
REC_MSG_ATTEMPTS unsuccessful attempts have been made, at which point
the server SHOULD abort the reconfigure process for that client.
Default and initial values for RECREP_MSG_TIMEOUT and
REC_MSG_ATTEMPTS are documented in section 7.5.
20.1.3. Receipt of Renew messages
The server generates and sends Reply message(s) to the client as
described in section 19.2.8, including in the "options" field new
values for configuration parameters.
It is possible that the client may send a Renew message after the
server has sent a Reconfigure but before the Reconfigure is received
by the client. In this case, the Renew message from the client
may not include all of the IAs and requests for parameters to be
reconfigured by the server. To accommodate this scenario, the server
MAY choose to send a Reply with the IAs and other parameters to be
reconfigured, even if those IAs and parameters were not in the Renew
message from the client.
20.2. Receipt of Information-request messages
If the server has assigned addresses to one or more IAs that belong
to the responding client, the server MUST silently discard the
Information-request message.
If the client has requested options in an Option Request option that
the server is unable to provide to the client, the server MAY send
a Reply message with only those options it can provide. If the
server sends a Reply message that does not include all of the options
Droms (ed.), et al. Expires 1 Aug 2002 [Page 49]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
requested by the client, it MUST include a Status Code option with
code OptionUnavail.
The server generates and sends Reply message(s) to the client as
described in section 19.2.8, including in the "options" field new
values for configuration parameters.
It is possible that the client may send an Information-request
message after the server has sent a Reconfigure but before
the Reconfigure is received by the client. In this case, the
Information-request message from the client may not request all of
the parameters to be reconfigured by the server. To accommodate
this scenario, the server MAY choose to send a Reply with the other
parameters to be reconfigured, even if those parameters were not
specified in the Information-request message from the client.
20.3. Client Behavior
A client MUST always monitor UDP port 546 for Reconfigure messages
on interfaces for which it has acquired DHCP parameters. Since the
results of a reconfiguration event may affect application layer
programs, the client SHOULD log these events, and MAY notify these
programs of the change through an implementation-specific interface.
20.3.1. Receipt of Reconfigure messages
Upon receipt of a valid Reconfigure message, the client initiates a
transaction with the server. While the transaction is in progress,
the client silently discards any Reconfigure messages it receives.
If the client has IAs with addresses that have been assigned by the
server from which the Reconfigure message was received, the client
MUST respond with a Renew message. Otherwise, the client responds
with an Information-request message.
DISCUSSION:
The Reconfigure message acts as a trigger that signals the
client to complete a successful message exchange. Once
the client has received a Reconfigure, the client proceeds
with the message exchange (retransmitting the Renew or
Information-request message if necessary); the client
ignores any additional Reconfigure messages (regardless
of the transaction ID in the Reconfigure message) until
the exchange is complete. Subsequent Reconfigure messages
(again independent of the transaction ID) cause the client
to initiate a new exchange.
How does this mechanism work in the face of duplicated or
retransmitted Reconfigure messages? Duplicate messages
will be ignored because the client will begin the exchange
Droms (ed.), et al. Expires 1 Aug 2002 [Page 50]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
after the receipt of the first Reconfigure. Retransmitted
messages will either trigger the exchange (if the first
Reconfigure was not received by the client) or will be
ignored. The server can discontinue retransmission of
Reconfigure messages to the client once the server receives
the Renew or Information-request message from the client.
It might be possible for a duplicate or retransmitted
Reconfigure to be sufficiently delayed (and delivered out of
order) to arrive at the client after the exchange (initiated
by the original Reconfigure) has been completed. In this
case, the client would initiate a redundant exchange. The
likelihood of delayed and out of order delivery is small
enough to be ignored. The consequence of the redundant
exchange is inefficiency rather than incorrect operation.
20.3.2. Creation and transmission of Renew messages
When responding to a Reconfigure, the client creates and sends
the Renew message in exactly the same manner as outlined in
section 19.1.3, with the exception: if the server included on Option
Request option specifying the IA option, the client MUST include IA
options containing the addresses the client currently has assigned to
ALL IAs for the interface through which the Reconfigure message was
received.
20.3.3. Creation and transmission of Information-request messages
When responding to a Reconfigure, the client creates and sends the
Information-request message in exactly the same manner as outlined in
section 19.1.5, with the exception that the client includes a Server
Identifier option with the identifier from the Reconfigure message to
which the client is responding.
20.3.4. Time out and retransmission of Renew or Information-request
messages
The client uses the same variables and retransmission algorithm as
it does with Renew or Information-request messages generated as part
of a client-initiated configuration exchange. See sections 19.1.3
and 19.1.5 for details.
20.3.5. Receipt of Reply messages
Upon the receipt of a valid Reply message, the client extracts the
contents of the "options" field, and sets (or resets) configuration
parameters appropriately. The client records and updates the
lifetimes for any addresses specified in IAs in the Reply message.
If the configuration parameters changed were requested by the
Droms (ed.), et al. Expires 1 Aug 2002 [Page 51]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
application layer, the client notifies the application layer of the
changes using an implementation-specific interface.
21. Relay Behavior
For this discussion, the Relay MAY be configured to use a list of
server destination addresses, which MAY include unicast addresses,
the All_DHCP_Servers multicast address, or other multicast addresses
selected by the network administrator. If the Relay has not been
explicitly configured, it MUST use the All_DHCP_Servers multicast
address as the default.
21.1. Relaying of client messages
When a Relay receives a valid client message, it constructs a
Relay-forward message. The relay places an address with a prefix
assigned to the link on which the client should be assigned an
address in the link-address field. This address will be used by the
server to determine the link from which the client should be assigned
an address and other configuration information.
If the relay cannot use the address in the link-address field to
identify the interface through which the response to the client will
be forwarded, the relay MUST include an Interface-id option (see
section 23.17) in the Relay-forward message. The server will include
the Interface-id option in its Relay-reply message.
The relay copies the source address from the IP datagram in which the
message was received from the client into the client-return-address
field in the Relay-forward message.
The relay constructs a "client-message" option 23.10 that contains
the entire message from the client in the data field of the
option. The relay places the "relay-message" option along with any
"relay-specific" options in the options field of the Relay-forward
message. The Relay MUST send the Relay-forward message to the list
of server destination addresses with which it has been configured.
21.2. Relaying of server messages
When the relay receives a Relay-reply message, it extracts the server
message from the "server-message" option. If the Relay-reply message
includes a Interface-id option, the relay forwards the message from
the server to the client on the link identified by the Interface-id
option. Otherwise, the relay forwards the message on the link
identified by the link-address field. In either case, the relay
forwards the message to the address in the client-return-address
field in the Relay-reply message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 52]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
22. Authentication of DHCP messages
Some network administrators may wish to provide authentication of
the source and contents of DHCP messages. For example, clients may
be subject to denial of service attacks through the use of bogus
DHCP servers, or may simply be misconfigured due to unintentionally
instantiated DHCP servers. Network administrators may wish to
constrain the allocation of addresses to authorized hosts to avoid
denial of service attacks in "hostile" environments where the network
medium is not physically secured, such as wireless networks or
college residence halls.
Because of the risk of denial of service attacks against DHCP
clients, the use of authentication is mandated in Reconfigure
messages. A DHCP server MUST include an authentication option in
Reconfigure messages sent to clients.
The DHCP authentication mechanism is based on the design of
authentication for DHCP for IPv4 [8].
22.1. DHCP threat model
The threat to DHCP is inherently an insider threat (assuming a
properly configured network where DHCPv6 ports are blocked on the
perimeter gateways of the enterprise). Regardless of the gateway
configuration, however, the potential attacks by insiders and
outsiders are the same.
The attack specific to a DHCP client is the possibility of the
establishment of a "rogue" server with the intent of providing
incorrect configuration information to the client. The motivation
for doing so may be to establish a "man in the middle" attack or it
may be for a "denial of service" attack.
There is another threat to DHCP clients from mistakenly or
accidentally configured DHCP servers that answer DHCP client requests
with unintentionally incorrect configuration parameters.
The threat specific to a DHCP server is an invalid client
masquerading as a valid client. The motivation for this may be for
"theft of service", or to circumvent auditing for any number of
nefarious purposes.
The threat common to both the client and the server is the resource
"denial of service" (DoS) attack. These attacks typically involve
the exhaustion of valid addresses, or the exhaustion of CPU or
network bandwidth, and are present anytime there is a shared
resource. In current practice, redundancy mitigates DoS attacks the
best.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 53]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
22.2. Security of messages sent between servers and relay agents
Relay agents and servers that choose to exchange messages securely
use the IPsec mechanisms for IPv6 [10]. The way in which IPsec
is employed by relay agents and servers is not specified in this
document.
22.3. Summary of DHCP authentication
Authentication of DHCP messages is accomplished through the use of
the Authentication option. The authentication information carried
in the Authentication option can be used to reliably identify the
source of a DHCP message and to confirm that the contents of the DHCP
message have not been tampered with.
The Authentication option provides a framework for multiple
authentication protocols. Two such protocols are defined here.
Other protocols defined in the future will be specified in separate
documents.
The protocol field in the Authentication option identifies the
specific protocol used to generate the authentication information
carried in the option. The algorithm field identifies a specific
algorithm within the authentication protocol; for example, the
algorithm field specifies the hash algorithm used to generate the
message authentication code (MAC) in the authentication option. The
replay detection method (RDM) field specifies the type of replay
detection used in the replay detection field.
22.4. Replay detection
The Replay Detection Method (RDM) field determines the type of replay
detection used in the Replay Detection field.
If the RDM field contains 0x00, the replay detection field MUST be
set to the value of a monotonically increasing counter. Using a
counter value such as the current time of day (e.g., an NTP-format
timestamp [12]) can reduce the danger of replay attacks. This method
MUST be supported by all protocols.
22.5. Configuration token protocol
If the protocol field is 0, the authentication information field
holds a simple configuration token. The configuration token is an
opaque, unencoded value known to both the sender and receiver. The
sender inserts the configuration token in the DHCP message and the
receiver matches the token from the message to the shared token. If
the configuration option is present and the token from the message
does not match the shared token, the receiver MUST discard the
message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 54]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Configuration token may be used to pass a plain-text configuration
token and provides only weak entity authentication and no message
authentication. This protocol is only useful for rudimentary
protection against inadvertently instantiated DHCP servers.
DISCUSSION:
The intent here is to pass a constant, non-computed token
such as a plain-text password. Other types of entity
authentication using computed tokens such as Kerberos
tickets or one-time passwords will be defined as separate
protocols.
22.6. Delayed authentication protocol
If the protocol field is 1, the message is using the "delayed
authentication" mechanism. In delayed authentication, the client
requests authentication in its Solicit message and the server replies
with an Advertise message that includes authentication information.
This authentication information contains a nonce value generated by
the source as a message authentication code (MAC) to provide message
authentication and entity authentication.
The use of a particular technique based on the HMAC protocol [11]
using the MD5 hash [20] is defined here.
22.6.1. Management issues in the delayed authentication protocol
The "delayed authentication" protocol does not attempt to address
situations where a client may roam from one administrative domain
to another, i.e. interdomain roaming. This protocol is focused on
solving the intradomain problem where the out-of-band exchange of a
shared secret is feasible.
22.6.2. Use of the Authentication option in the delayed authentication
protocol
In a Solicit message, the Authentication option carries the Protocol,
Algorithm, RDM and Replay detection fields, but no Authentication
information.
In an Advertise, Request, Renew, Rebind, Confirm, Decline, Release
or Information-request message, the Authentication option carries
the Protocol, Algorithm, RDM and Replay detection fields and
Authentication information.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 55]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The format of the Authentication information is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Secret ID (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| HMAC-MD5 (128 bits) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The following definitions will be used in the description of the
authentication information for delayed authentication, algorithm 1:
Replay Detection - as defined by the RDM field
K - a secret value shared between the source and
destination of the message; each secret has a
unique identifier (secret ID)
secret ID - the unique identifier for the secret value
used to generate the MAC for this message
HMAC-MD5 - the MAC generating function.
The sender computes the MAC using the HMAC generation algorithm [11]
and the MD5 hash function [20]. The entire DHCP message (except
the MAC field of the authentication option itself), including the
DHCP message header and the options field, is used as input to the
HMAC-MD5 computation function. The 'secret ID' field MUST be set to
the identifier of the secret used to generate the MAC.
DISCUSSION:
Algorithm 1 specifies the use of HMAC-MD5. Use of a
different technique, such as HMAC-SHA, will be specified as
a separate protocol.
Delayed authentication requires a shared secret key for each
client on each DHCP server with which that client may wish
to use the DHCP protocol. Each secret key has a unique
identifier that can be used by a receiver to determine which
secret was used to generate the MAC in the DHCP message.
Therefore, delayed authentication may not scale well in an
architecture in which a DHCP client connects to multiple
administrative domains.
22.6.3. Message validation
To validate an incoming message, the receiver first checks that
the value in the replay detection field is acceptable according
Droms (ed.), et al. Expires 1 Aug 2002 [Page 56]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
to the replay detection method specified by the RDM field. Next,
the receiver computes the MAC as described in [11]. The receiver
MUST set the 'MAC' field of the authentication option to all 0s for
computation of the MAC. If the MAC computed by the receiver does not
match the MAC contained in the authentication option, the receiver
MUST discard the DHCP message.
22.6.4. Key utilization
Each DHCP client has a key, K. The client uses its key to encode
any messages it sends to the server and to authenticate and verify
any messages it receives from the server. The client's key SHOULD
be initially distributed to the client through some out-of-band
mechanism, and SHOULD be stored locally on the client for use in all
authenticated DHCP messages. Once the client has been given its key,
it SHOULD use that key for all transactions even if the client's
configuration changes; e.g., if the client is assigned a new network
address.
Each DHCP server MUST know, or be able to obtain in a secure manner,
the keys for all authorized clients. If all clients use the same
key, clients can perform both entity and message authentication for
all messages received from servers. However, the sharing of keys
is strongly discouraged as it allows for unauthorized clients to
masquerade as authorized clients by obtaining a copy of the shared
key. To authenticate the identity of individual clients, each client
MUST be configured with a unique key.
22.6.5. Client considerations for delayed authentication protocol
22.6.5.1. Sending Solicit messages
When the client sends a Solicit message and wishes to use
authentication, it includes an Authentication option with the desired
protocol, algorithm, RDM and replay detection field as described
in section 22.6. The client does not include any authentication
information in the Authentication option.
22.6.5.2. Receiving Advertise messages
The client validates any Advertise messages containing an
Authentication option specifying the delayed authentication protocol
using the validation test described in section 22.6.3.
Client behavior if no Advertise messages include authentication
information or pass the validation test is controlled by local policy
on the client. According to client policy, the client MAY choose to
respond to a Advertise message that has not been authenticated.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 57]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The decision to set local policy to accept unauthenticated messages
should be made with care. Accepting an unauthenticated Advertise
message can make the client vulnerable to spoofing and other
attacks. If local users are not explicitly informed that the client
has accepted an unauthenticated Advertise message, the users may
incorrectly assume that the client has received an authenticated
address and is not subject to DHCP attacks through unauthenticated
messages.
A client MUST be configurable to discard unauthenticated messages,
and SHOULD be configured by default to discard unauthenticated
messages. A client MAY choose to differentiate between Advertise
messages with no authentication information and Advertise messages
that do not pass the validation test; for example, a client might
accept the former and discard the latter. If a client does accept an
unauthenticated message, the client SHOULD inform any local users and
SHOULD log the event.
22.6.5.3. Sending Request, Confirm, Renew, Rebind, Decline or Release
messages
If the client authenticated the Advertise message through which the
client selected the server, the client MUST generate authentication
information for subsequent Request, Confirm, Renew, Rebind or Release
messages sent to the server as described in section 22.6. When the
client sends a subsequent message, it MUST use the same secret used
by the server to generate the authentication information.
22.6.5.4. Sending Information-request messages
If the client has negotiated a secret with the server through a
previous message exchange, the client MUST use the same secret used
by the server to generate the authentication information. If the
client has not negotiated a secret with the server, the client MUST
use a secret that has been selected for the client through some
external mechanism.
22.6.5.5. Receiving Reply messages
If the client authenticated the Advertise it accepted, the client
MUST validate the associated Reply message from the server. The
client MUST discard the Reply if the message fails to pass validation
and MAY log the validation failure. If the Reply fails to pass
validation, the client MUST restart the DHCP configuration process by
sending a Solicit message. The client MAY choose to remember which
server replied with a Reply message that failed to pass validation
and discard subsequent messages from that server.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 58]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
If the client accepted an Advertise message that did not include
authentication information or did not pass the validation test, the
client MAY accept an unauthenticated Reply message from the server.
22.6.5.6. Receiving Reconfigure messages
The client MUST validate the Reconfigure message from the server.
The client MUST discard the Reconfigure if the message fails to pass
validation and MAY log the validation failure.
22.6.6. Server considerations for delayed authentication protocol
22.6.6.1. Receiving Solicit messages and Sending Advertise messages
The server selects a secret for the client and includes
authentication information in the Advertise message returned to the
client as specified in section 22.6. The server MUST record the
identifier of the secret selected for the client and use that same
secret for validating subsequent messages with the client.
22.6.6.2. Receiving Request, Confirm, Renew, Rebind or Release messages
and Sending Reply messages
The server uses the secret identified in the message and validates
the message as specified in section 22.6.3. If the message fails to
pass validation or the server does not know the secret identified by
the 'secret ID' field, the server MUST discard the message and MAY
choose to log the validation failure.
If the message passes the validation procedure, the server responds
to the specific message as described in section 19.2. The server
MUST include authentication information generated using the secret
identified in the received message as specified in section 22.6.
22.6.6.3. Sending Reconfigure messages
The server MUST include authentication information in a Reconfigure
message, generated as specified in section 22.6 using the secret the
server initially negotiated with the client to which the Reconfigure
message is to be sent.
If the server has not previously negotiated a secret with the client,
the server MUST use a secret that has been selected for the client
through some external mechanism.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 59]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
23. DHCP options
Options are used to carry additional information and parameters
in DHCP messages. Every option shares a common base format, as
described in section 23.1. All values in options is represented in
network order.
This document describes the DHCP options defined as part of the base
DHCP specification. Other options may be defined in the future in a
separate document.
23.1. Format of DHCP options
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| option-code | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| option-data |
| (option-len octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code An unsigned integer identifying the specific option
type carried in this option.
option-len An unsigned integer giving the length of the
option-data field in this option in octets.
option-data The data for the option; the format of this data
depends on the definition of the option.
DHCPv6 options are scoped by using encapsulation. Some options apply
generally to the client, some are specific to an IA, and some are
specific to the addresses within an IA. These latter two cases are
discussed in sections 23.4 and 23.5.
23.2. Client Identifier option
The Client Identifier option is used to carry a DUID identifying a
client between a client and a server. The Client Identifier option
MUST appear before any IA options in the DHCP message. The format of
the DUID option is:
Droms (ed.), et al. Expires 1 Aug 2002 [Page 60]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_CLIENTID | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. DUID .
. (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_CLIENTID (TBD)
option-len Length of DUID in octets
option-data The DUID for the client
23.3. Server Identifier option
The Server Identifier option is used to carry a DUID identifying
a server between a client and a server. The format of the Server
Identifier option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_SERVERID | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. DUID .
. (variable length) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_SERVERID (TBD)
option-len Length of DUID in octets
option-data The DUID for the server
23.4. Identity association option
The identity association option is used to carry an identity
association, the parameters associated with the IA and the addresses
assigned to the IA.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 61]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The format of the IA option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION IA | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IAID (4 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| T1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| T2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IA Status | |
+-+-+-+-+-+-+-+-+ |
. Options .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_IA (TBD)
option-len See section 23.
IAID The unique identifier for this IA.
T1 The time at which the client contacts the
server from which the addresses in the IA
were obtained to extend the lifetimes of the
addresses assigned to the IA.
T2 The time at which the client contacts any
available server to extend the lifetimes of
the addresses assigned to the IA.
IA status Status of the IA in this option.
options Options associated with this IA.
The Options field encapsulates those options that are specific
to this IA. For example, all of the Address Options carrying the
addresses associated with this IA are in the Options field.
Note that an IA has no explicit "lifetime" or "lease length" of
its own. When the lifetimes of all of the addresses in an IA have
expired, the IA can be considered as having expired. T1 and T2
are included to give servers explicit control over when a client
recontacts the server about a specific IA.
In a message sent by a client to a server, values in the T1 and
T2 fields indicate the client's preference for those parameters.
The client may send 0 if it has no preference for T1 and T2. In a
Droms (ed.), et al. Expires 1 Aug 2002 [Page 62]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
message sent by a server to a client, the client MUST use the values
in the T1 and T2 fields for the T1 and T2 parameters. The values in
the T1 and T2 fields are the number of seconds until T1 and T2.
The server MUST set the T1 and T2 times to values that will allow
the client to extend as appropriate the lifetimes of any addresses
in the IA. If the server does not intend for a client to extend the
lifetimes of a particular address in an IA, the server MAY set the
renewal time values to occur after the lifetimes on that address
expire.
T1 is the time at which the client SHOULD begin the lifetime
extension process by sending a Renew message to the server that
originally assigned the addresses to the IA. T2 is the time at which
the client SHOULD start sending a Rebind message to any server. A
client MAY begin the lifetime extension process prior to T1 if it
needs additional addresses for some reason.
T1 and T2 are specified as unsigned integers that specify the time
in seconds relative to the time at which the messages containing the
option is received.
23.5. IA Address option
The IA Address option is used to specify IPv6 addresses associated
with an IA. The IA Address option must be encapsulated in the
Options field of an Identity Association option. The Options field
encapsulates those options that are specific to this address.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 63]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The format of the IA Address option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_IAADDR | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|T| addr status | prefix length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| IPv6 address |
| (16 octets) |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | preferred lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| pref. lifetime (cont.) | valid lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| valid lifetime (cont.) | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
. .
. Options .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_IADDR (TBD)
option-len See section 23.
T When set to 1, indicates that this address is a
"temporary address" [16]; when set to 0, the address
is not a temporary address.
addr status Status of this address in this IA.
prefix length Prefix length for this address.
IPv6 address An IPv6 address
preferred lifetime The preferred lifetime for the IPv6 address in
the option.
valid lifetime The valid lifetime for the IPv6 address in the
option
options Options associated with this address
In a message sent by a client to a server, values in the preferred
and valid lifetime fields indicate the client's preference for those
parameters. The client may send 0 if it has no preference for the
preferred and valid lifetimes. In a message sent by a server to a
client, the client MUST use the values in the preferred and valid
Droms (ed.), et al. Expires 1 Aug 2002 [Page 64]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
lifetime fields for the preferred and valid lifetimes. The values in
the preferred and valid lifetimes are the number of seconds remaining
in each lifetime.
One or more IA Address Options can appear anywhere in an IA option.
23.6. Requested Temporary Addresses (RTA) Option
The Requested Temporary Addresses (RTA) option is used by a client to
request a server to assign additional temporary addresses to an IA.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_RTA | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| num-requested |
+-+-+-+-+-+-+-+-+
option-code OPTION_RTA (TBD)
option-len See section 23.
num-requested The number of additional temporary addresses the
client is requesting. This is an unsigned value.
This option MUST only be sent by a client and only in a Solicit,
Request, Renew, or Rebind message. It MUST only appear encapsulated
within an Identity association option. A client MUST only include
this option when it wants to have additional temporary address
allocated; a client SHOULD NOT send this option if 'num-requested' is
0.
23.7. Option Request option
The Option Request option is used to identify a list of options in a
message between a client and a server.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 65]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The format of the Option Request option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_ORO | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| requested-option-code-1 | requested-option-code-2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_ORO (TBD)
option-len See section 23.
requested-option-code-n The option code for an option requested by
the client.
A client MAY include an Option Request option in a Solicit, Request,
Renew, Rebind, Confirm or Information-request message to inform the
server about options the client wants the server to send to the
client.
23.8. Preference option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_PREFERENCE | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| pref value |
+-+-+-+-+-+-+-+-+
option-code OPTION_PREFERENCE (TBD)
option-len See section 23.
pref value The preference value for the server in this message.
A server MAY include a Preference option in an Advertise message to
control the selection of a server by the client. See section 18.1.3
for the use of the Preference option by the client and the
interpretation of Preference option data value.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 66]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
23.9. Elapsed Time
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_ELAPSED_TIME | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| elapsed time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_ELAPSED_TIME (TBD)
option-len See section 23.
elapsed time The amount of time since the client began its
current DHCP transaction. This time is expressed in
hundredths of a second (10^-2 seconds).
A client MAY include an Elapsed Time option in messages to indicate
how long the client has been trying to complete a DHCP transaction.
Servers and Relay Agents MAY use the data value in this option
as input to policy controlling how a server responds to a client
message.
23.10. Client message option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_CLIENT_MSG | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. DHCP client message .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_CLIENT_MSG (TBD)
option-len See section 23.
DHCP client message The message received from the client;
forwarded verbatim to the server.
A relay agent forwards a message from a client to a server as the
contents of a Client Message option in a Relay-forward message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 67]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
23.11. Server message option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_SERVER_MSG | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. DHCP server message .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_SERVER_MSG (TBD)
option-len See section 23.
DHCP server message The message received from the server;
forwarded verbatim to the client.
A server sends a DHCP message to be forwarded to a client by a relay
agent as the contents of a Server Message option in a Relay-reply
message.
23.12. Authentication option
The Authentication option carries authentication information to
authenticate the identity and contents of DHCP messages. The use of
the Authentication option is described in section 22. If present,
the Authentication option MUST appear as the first option in the DHCP
message.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 68]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
The format of the Authentication option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_AUTH | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Protocol | Algorithm | RDM | Replay detect.|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Replay Detection (64 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Replay cont. | Auth. Info |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Authentication Information |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_AUTH (TBD)
option-len See section 23.
protocol The authentication protocol used in
this authentication option
algorithm The algorithm used in the
authentication protocol
RDM The replay detection method used in
this authentication option
Replay detection The replay detection information for
the RDM
Authentication information The authentication information,
as specified by the protocol and
algorithm used in this authentication
option
23.13. Server unicast option
The server MAY send this option to a client to indicate to the client
that is allowed to unicast messages to the server. The server
specifies the IPv6 address to which the client is to send unicast
messages in the server-address field. When a client receives this
option, where permissible, the client MAY send messages directly to
the server using the IPv6 address specified in the server-address
field of the option.
Details about when the client may send messages to the server using
unicast are in section 19.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 69]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_UNICAST | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| server-address |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_UNICAST (TBD)
option-len See section 23.
server-address The IP address to which the client should send
messages delivered using unicast
23.14. Status Code Option
This option returns a status indication related to the DHCP message
in which it appears.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_STATUS_CODE | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| status-code | status-message |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_STATUS_CODE (TBD)
option-len See section 23.
status-code The numeric code for the status encoded in
this option. The status codes are defined in
section 7.4.
status-message A UTF-8 encoded text string, which MUST NOT
be null-terminated.
23.15. User Class Option
This option is used by a client to identify the type or category of
user or applications it represents. The information contained in the
Droms (ed.), et al. Expires 1 Aug 2002 [Page 70]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
data area of this option is contained in one or more opaque fields
that represent the user class or classes of which the client is a
member. The user class information carried in this option MUST be
configurable on the client.
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_USER_CLASS | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| user class data |
| . . . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code TBD
option-len See section 23.
user class data The user classes carried by the client.
The data area of the user class option MUST contain one or more
instances of user class data. Each instance of the user class data
is formatted as follows:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-...-+-+-+-+-+-+-+
| user class len | user class data |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-...-+-+-+-+-+-+-+
The user class len is two octets long and specifies the length of the
opaque user class data in network order.
Servers can interpret the meanings of multiple class specifications
in an implementation dependent or configuration dependent manner,
and so the use of multiple classes by a DHCP client should be based
on the specific server implementation and configuration which will
be used to process that User class option. Servers not equipped to
interpret the user class information sent by a client MUST ignore it
(although it may be reported).
23.16. Vendor Class Option
This option is used by clients and servers to exchange
vendor-specific information. The definition of this information
is vendor specific. The vendor is indicated in the vendor
class identifier option. Servers not equipped to interpret
the vendor-specific information sent by a client MUST ignore it
(although it may be reported). Clients which do not receive desired
vendor-specific information SHOULD make an attempt to operate without
it, although they may do so (and announce they are doing so) in a
degraded mode.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 71]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_VENDOR_CLASS | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| vendor-id |
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| option-data |
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code TBD
option-len See section 23.
vendor-id A domain name belonging to the vendor used to
identify the vendor that defined this vendor
class option.
option-data An opaque object of option-len octets,
presumably interpreted by vendor-specific
code on the clients and servers
The vendor-id must adhere to the rules in section 10.
The Encapsulated vendor-specific options field MUST be encoded as
a sequence of code/length/value fields of identical format to the
DHCP options field. Each of the encapsulated options is formatted as
follows.
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| opt-code | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| option-data |
| . . . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
opt-code The code for the encapsulated option
option-len See section 23.
option-data The data area for the encapsulated option
23.17. Interface-Id Option
The relay agent MAY send the Interface-id option to identify the
interface on which the client message was received. If a relay
Droms (ed.), et al. Expires 1 Aug 2002 [Page 72]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
receives a Relay-reply message with an Interface-id option, the relay
forwards the message to the client through the interface identified
by the option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_INTERFACE_ID | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Interface-Id |
. .
. .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_INTERFACE_ID (TBD)
option-len See section 23.
Interface-Id An opaque value of arbitrary length generated
by the relay agent to identify one of the
relay agent's interfaces
The server MUST copy the Interface-Id option from the Relay-Forward
message into the Relay-Reply message the server sends to the relay
agent in response to the Relay-Forward message. This option MUST NOT
appear in any message except a Relay-Forward or Relay-Reply message.
Servers MAY use the Interface-ID for parameter assignment policies.
The Interface-ID SHOULD be considered an opaque value, with policies
based on exact string match only; that is, the Interface-ID SHOULD
NOT be internally parsed by the server.
24. Security Considerations
Section 22 describes a threat model and an option that provides an
authentication framework to defend against that threat model.
25. Year 2000 considerations
Since all times are relative to the current time of the transaction,
there is no problem within the DHCPv6 protocol related to any
hardcoded dates or two-digit representation of the current year.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 73]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
26. IANA Considerations
This document defines several new name spaces associated with DHCPv6
and DHCPv6 options. IANA is requested to manage the allocation of
values from these name spaces, which are described in the remainder
of this section. These name spaces are all to be managed separately
from the name spaces defined for DHCPv4 [7, 1].
New values in each of these name spaces should be approved by the
process of IETF consensus [15].
26.1. Multicast addresses
Section 7.1 defines the following multicast addresses, which have
been assigned by IANA for use by DHCPv6:
All_DHCP_Agents address: FF02::1:2
All_DHCP_Servers address: FF05::1:3
IANA is requested to manage definition of additional multicast
addresses in the future.
26.2. DHCPv6 message types
IANA is requested to record the message types defined in section 7.3.
IANA is requested to manage definition of additional message types in
the future.
26.3. DUID
IANA is requested to record the DUID types defined in section 11.1.
IANA is requested to manage definition of additional DUID types in
the future.
26.4. DHCPv6 options
IANA is requested to assign option-codes to the options defined in
section 23. IANA is requested to manage the definition of additional
DHCPv6 option-codes in the future.
26.5. Status codes
IANA is requested to record the status codes defined in section 7.4.
IANA is requested to manage the definition of additional status codes
in the future.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 74]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
26.6. Authentication option
Section 22 defines three new name spaces associated with the
Authentication Option (section 23.12), which are to be created and
maintained by IANA: Protocol, Algorithm and RDM.
Initial values assigned from the Protocol name space are 0 (for the
configuration token Protocol in section 22.5) and 1 (for the delayed
authentication Protocol in section 22.6). Additional protocols may
be defined in the future.
The Algorithm name space is specific to individual Protocols. That
is, each Protocol has its own Algorithm name space. The guidelines
for assigning Algorithm name space values for a particular protocol
should be specified along with the definition of a new Protocol.
For the configuration token Protocol, the Algorithm field MUST be
0, as described in section 22.5. For the delayed authentication
Protocol, the Algorithm value 1 is assigned to the HMAC-MD5
generating function as defined in section 22.6. Additional
algorithms for the delayed authentication protocol may be defined in
the future.
The initial value of 0 from the RDM name space is assigned to the
use of a monotonically increasing value as defined in section 22.4.
Additional replay detection methods may be defined in the future.
27. Acknowledgments
Thanks to the DHC Working Group for their time and input into the
specification. In particular, thanks also for the consistent input,
ideas, and review by (in alphabetical order) Thirumalesh Bhat,
Vijayabhaskar, Brian Carpenter, Matt Crawford, Francis Dupont,
Josh Littlefield, Gerald Maguire, Jack McCann, Thomas Narten, Erik
Nordmark, Yakov Rekhter, Mark Stapp, Matt Thomas, Sue Thomson, and
Phil Wells.
Thanks to Steve Deering and Bob Hinden, who have consistently
taken the time to discuss the more complex parts of the IPv6
specifications.
Bill Arbaugh reviewed the authentication mechanism described in
section 22.
And, thanks to Steve Deering for pointing out at IETF 51 in London
that the DHCPv6 specification has the highest revision number of any
Internet Draft.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 75]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
References
[1] S. Alexander and R. Droms. DHCP Options and BOOTP Vendor
Extensions, March 1997. RFC 2132.
[2] S. Bradner. Key words for use in RFCs to Indicate Requirement
Levels, March 1997. RFC 2119.
[3] S. Bradner and A. Mankin. The Recommendation for the IP Next
Generation Protocol, January 1995. RFC 1752.
[4] W.J. Croft and J. Gilmore. Bootstrap Protocol, September 1985.
RFC 951.
[5] S. Deering and R. Hinden. Internet Protocol, Version 6 (IPv6)
Specification, December 1998. RFC 2460.
[6] R. Draves. Default Address Selection for IPv6, September 2001.
work in progress.
[7] R. Droms. Dynamic Host Configuration Protocol, March 1997. RFC
2131.
[8] R. Droms, Editor, W. Arbaugh, and Editor. Authentication for
DHCP Messages, June 2001. RFC 3118.
[9] R. Hinden and S. Deering. IP Version 6 Addressing Architecture,
July 1998. RFC 2373.
[10] S. Kent and R. Atkinson. Security Architecture for the Internet
Protocol, November 1998. RFC 2401.
[11] H. Krawczyk, M. Bellare, and R. Canetti. HMAC: Keyed-Hashing
for Message Authentication, February 1997. RFC 2104.
[12] David L. Mills. Network Time Protocol (Version 3)
Specification, Implementation, March 1992. RFC 1305.
[13] P.V. Mockapetris. Domain names - concepts and facilities,
November 1987. RFC 1034.
[14] P.V. Mockapetris. Domain names - implementation and
specification, November 1987. RFC 1035.
[15] T. Narten and H. Alvestrand. Guidelines for Writing an IANA
Considerations Section in RFCs, October 1998. RFC 2434.
[16] T. Narten and R. Draves. Privacy Extensions for Stateless
Address Autoconfiguration in IPv6, January 2001. RFC 3041.
[17] T. Narten, E. Nordmark, and W. Simpson. Neighbor Discovery for
IP Version 6 (IPv6), December 1998. RFC 2461.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 76]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
[18] D.C. Plummer. Ethernet Address Resolution Protocol: Or
converting network protocol addresses to 48.bit Ethernet address
for transmission on Ethernet hardware, November 1982. RFC 826.
[19] J. Postel. User Datagram Protocol, August 1980. RFC 768.
[20] R. Rivest. The MD5 Message-Digest Algorithm, April 1992. RFC
1321.
[21] S. Thomson and T. Narten. IPv6 Stateless Address
Autoconfiguration, December 1998. RFC 2462.
[22] P. Vixie, Ed., S. Thomson, Y. Rekhter, and J. Bound. Dynamic
Updates in the Domain Name System (DNS UPDATE), April 1997. RFC
2136.
Chair's Address
The working group can be contacted via the current chair:
Ralph Droms
Cisco Systems
300 Apollo Drive
Chelmsford, MA 01824
Phone: (978) 244-4733
E-mail: rdroms@cisco.com
Authors' Addresses
Questions about this memo can be directed to:
Droms (ed.), et al. Expires 1 Aug 2002 [Page 77]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Jim Bound
Compaq Computer Corporation
ZK3-3/W20
110 Spit Brook Road
Nashua, NH 03062-2698
USA
Voice: +1 603 884 0062
E-mail: Jim.Bound@compaq.com
Mike Carney
Sun Microsystems, Inc
Mail Stop: UMPK17-202
901 San Antonio Road
Palo Alto, CA 94303-4900
USA
Voice: +1-650-786-4171
E-mail: mwc@eng.sun.com
Charles E. Perkins
Communications Systems Lab
Nokia Research Center
313 Fairchild Drive
Mountain View, California 94043
USA
Voice: +1-650 625-2986
E-mail: charliep@iprg.nokia.com
Fax: +1 650 625-2502
Ted Lemon
Nominum, Inc.
950 Charter Street
Redwood City, CA 94043
E-mail: Ted.Lemon@nominum.com
Bernie Volz
Ericsson
959 Concord St
Framingham, MA 01701
Voice: +1-508-875-3162
Fax: +1-508-875-3018
E-mail: bernie.volz@ericsson.com
Ralph Droms
Cisco Systems
300 Apollo Drive
Chelmsford, MA 01824
USA
Voice: +1 978 479 4733
E-mail: rdroms@cisco.com
Droms (ed.), et al. Expires 1 Aug 2002 [Page 78]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
A. Appearance of Options in Message Types
The following table indicates with a "*" the options are allowed in
each DHCP message type:
Client Server IA RTA Option Pref Time Client Server
ID ID Request Forw. Forw.
Solicit * * * *
Advert. * * * * * *
Request * * * * *
Confirm * * * *
Renew * * * * *
Rebind * * * *
Decline * * * * *
Release * * * * *
Reply * * * * * *
Reconf. * * *
Inform. * (see note) *
R-forw. * *
R-repl. * *
NOTE:
Only included in Information-Request messages that are sent
in response to a Reconfigure (see section 20.3.3).
Auth Server Status User Vendor
Unica. Code Class Class
Solicit * * *
Advert. * * *
Request * * *
Confirm * * *
Renew * * *
Rebind * * *
Decline * * * *
Release * * * *
Reply * * *
Reconf. *
Inform. * * *
R-forw. * *
R-repl. * *
B. Appearance of Options in the Options Field of DHCP Messages
The following table indicates with a "*" where options can appear in
the options field or encapsulated in other options:
Droms (ed.), et al. Expires 1 Aug 2002 [Page 79]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
Option IA IAADDR RTA Client Server
Field Forw. Forw.
Client msg. * *
Server msg. * *
DUID *
IA *
IAADDR *
RTA *
ORO *
Pref *
Time *
Client Forw. *
Server Forw. *
DSTM Addr. *
DSTM Tunnel *
Authentic. *
Server Uni. *
Dom. Srch. *
Dom. Server *
Status Cod. * * *
Circ. ID * *
User Class *
Vend. Class *
C. Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However,
this document itself may not be modified in any way, such as by
removing the copyright notice or references to the Internet Society
or other Internet organizations, except as needed for the purpose
of developing Internet standards in which case the procedures
for copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
Droms (ed.), et al. Expires 1 Aug 2002 [Page 80]
Internet Draft DHCP for IPv6 (-23) 1 Feb 2002
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Droms (ed.), et al. Expires 1 Aug 2002 [Page 81]