Network Working Group                                           R. Droms
Internet-Draft                                             Cisco Systems
Expires: July 13, 2004                                  January 13, 2004


                    Stateless DHCP Service for IPv6
                 draft-ietf-dhc-dhcpv6-stateless-04.txt

Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at http://
   www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on July 13, 2004.

Copyright Notice

   Copyright (C) The Internet Society (2004). All Rights Reserved.

Abstract

   Stateless DHCP service for IPv6 (DHCPv6) is used by nodes to obtain
   configuration information such as the addresses of DNS recursive name
   servers that does not require the maintenance of any dynamic state
   for individual clients. A node that uses stateless DHCP must have
   obtained its IPv6 addresses through some other mechanism, typically
   stateless address autoconfiguration. This document explains which
   parts of RFC3315 must be implemented in each of the different kinds
   of DHCP agents so that that agent can support stateless DHCP.

1. Introduction

   Nodes that have obtained IPv6 addresses through some other mechanism
   such as stateless address autoconfiguration [6] or manual



Droms                    Expires July 13, 2004                  [Page 1]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   configuration can use stateless DHCP to obtain other configuration
   information such as a list of DNS recursive name servers or SIP
   servers.  A stateless DHCP server provides only configuration
   information to nodes and does not perform any address assignment.
   Such a server is called "stateless" because it need not maintain any
   dynamic state for individual clients.

   While the DHCP specification [1] defines more than 10 protocol
   messages and 20 options, only a subset of those messages and options
   are required for stateless DHCP service. This document explains which
   messages and options defined in RFC 3315 are required for stateless
   DHCP service. The intended use of the document is to guide the
   interoperable implementation of clients and servers that use
   stateless DHCP service.

   The operation of relay agents is the same for stateless and stateful
   DHCP service.  The operation of relay agents is described in the DHCP
   specification.

   Section 4 of this document lists the sections of the DHCP document
   that an implementor should read for an overview of the DHCP
   specification and the basic requirements of a DHCP service. Section 5
   lists the specific messages and options that are specifically
   required for stateless DHCP service.  Section 6 describes how
   stateless and stateful DHCP servers interact to provide service to
   clients that require address assignment and clients that require only
   stateless service.

2. Terminology

   Throughout this document, "DHCP" refers to DHCP for IPv6.

   This document uses the terminology defined in RFC2460 [2], the DHCP
   specification [1] and the DHCP DNS configuration options
   specification [3].

   "Stateless DHCP" refers to the use of DHCP to provide configuration
   information to clients that does not require the server to maintain
   dynamic state about the DHCP clients.

3. Overview

   This document assumes that a node using stateless DHCP configuration
   is not using DHCP for address assignment, and that a node has
   determined at least a link-local address as described in section 5.3
   of RFC2461 [4].

   To obtain configuration parameters through stateless DHCP, a node



Droms                    Expires July 13, 2004                  [Page 2]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   uses the DHCP Information-request message. DHCP servers respond to
   the node's message with a Reply message that carries configuration
   parameters for the node.  The Reply message from the server can carry
   configuration information such as a list of DNS recursive name
   servers [3] and SIP servers [5].

   This document does not apply to the function of DHCP relay agents as
   described in RFC 3315. A network element can provide both DHCP server
   and DHCP relay service.  For example, a network element can provide
   stateless DHCP service to hosts requesting stateless DHCP service,
   while relaying messages from hosts requesting address assignment
   through DHCP to another DHCP server.

4. Basic Requirements for Implementation of DHCP

   Several sections of the DHCP specification provide background
   information or define parts of the specification that are common to
   all implementations:

   1-4:   give an introduction to DHCP and an overview of DHCP message
      flows

   5:     defines constants used throughout the protocol specification

   6, 7:  illustrates the format of DHCP messages

   8:     describes the representation of Domain Names

   9:     defines the "DHCP unique identifier" (DUID)

   13-16: describe DHCP message transmission, retransmission and
      validation

   21:    describes authentication for DHCP


5. Implementation of Stateless DHCP

   The client indicates that it is requesting configuration information
   by sending an Information-request message that includes an Option
   Request option specifying the options that it wishes to receive from
   the DHCP server.  For example, if the client is attempting to obtain
   a list of DNS recursive name servers, it identifies the DNS Recursive
   Name Server option in the Information-request message. The server
   determines the appropriate configuration parameters for the client
   based on its configuration policies and responds with a Reply message
   containing the requested parameters.  In this example, the server
   would respond with DNS configuration parameters.



Droms                    Expires July 13, 2004                  [Page 3]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   As described in section 18.1.5 of RFC 3315, a node may include a
   Client Identifier option in the Information-request message to
   identify itself to a server, because the server administrator may
   want to customize the server's response to each node, based on the
   node's identity.

   RFC 3315 does not define any mechanisms through which the time at
   which a host uses an Information-request message to obtain updated
   configuration parameters can be controlled.  The dhc WG has
   undertaken the development of such a mechanism or mechanisms which
   will be published as Standards-track RFC(s).

   RFC 3315 also does not provide any guidance about when a host might
   use an Information-request message to obtain updated configuration
   parameters when the host has moved to a new link. The dhc WG is
   reviewing a related document, "Detection of Network Attachment (DNA)
   in IPv4" [8], which describes how a host using IPv4 can determine
   when to use DHCPv4.  Either the dhc WG or a WG formed from the dna
   BOF will undertake development of a similar document for IPv6.

5.1 Messages Required for Stateless DHCP Service

   Clients and servers implement the following messages for stateless
   DHCP service; the section numbers in this list refer to the DHCP
   specification:

   Information-request: sent by a DHCP client to a server to request
      configuration parameters (sections 18.1.5 and 18.2.5)

   Reply:               sent by a DHCP server to a client containing
      configuration parameters (sections 18.2.6 and 18.2.8)

   In addition, servers and relay agents implement the following
   messages for stateless DHCP service; the section numbers in this list
   refer to the DHCP specification:

   Relay-forward: Sent by a DHCP relay agent to carry the client message
      to a server (section 15.13)

   Relay-reply:   Sent by a DHCP server to carry a response message to
      the relay agent (section 15.14)


5.2 Options Required for Stateless DHCP Service

   Clients and servers implement the following options for stateless
   DHCP service; the section numbers in this list refer to the DHCP
   specification:



Droms                    Expires July 13, 2004                  [Page 4]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   Option Request:    specifies the configuration information that the
      client is requesting from the server (section 22.7)

   Status Code:       used to indicate completion status or other status
      information (section 22.13)

   Server Identifier: used to identify the server responding to a client
      request (section 22.3)

   Servers and relay agents implement the following options for
   stateless DHCP service; the section numbers in this list refer to the
   DHCP specification:

   Client message: Sent by a DHCP relay agent in a Relay-forward message
      to carry the client message to a server (section 20)

   Server message: Sent by a DHCP server in a Relay-reply message to
      carry a response message to the relay agent (section 20)

   Interface-ID:   Sent by the DHCP relay agent and returned by the
      server to identify the interface to use to forward a message to
      the client (section 22.18)


5.3 Options Used for Configuration Information

   Clients and servers use the following options to pass configuration
   information to clients; note that other options for configuration
   information may be specified in future Internet Standards:

   DNS Recursive Name Servers: specifies the DNS recursive name servers
      [7] the client uses for name resolution; see "DNS Configuration
      options for DHCPv6" [3]

   DNS search list:            specifies the domain names to be searched
      during name resolution; see "DNS Configuration options for DHCPv6"
      [3]

   SIP Servers:                specifies the SIP servers the client uses
      to obtain a list of domain names of IPv6 addresses that can be
      mapped to one or more SIP outbound proxy servers [5]


5.4 Other Options Used in Stateless DHCP

   Clients and servers may implement the following options for stateless
   DHCP service; the section numbers in this list refer to the DHCP
   specification:



Droms                    Expires July 13, 2004                  [Page 5]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   Preference:     Sent by a DHCP server to indicate the preference
      level for the server (section 22.8)

   Elapsed time:   Sent by a DHCP client to indicate the time since the
      client began the DHCP configuration process (section 22.9)

   User Class:     Sent by a DHCP client to give additional information
      to the server for selecting configuration parameters for the
      client (section 22.15)

   Vendor Class:   Sent by a DHCP client to give additional information
      about the client vendor and hardware to the server for selecting
      configuration parameters for the client (section 22.16)

   Vendor-specific Information: Used to pass information to clients in
      options defined by vendors (section 22.17)

   Client Identifier: Sent by a DHCP client to identify itself (section
      22.2).  Clients are not required to send this option; servers send
      the option back if included in a message from a client

   Authentication: Used to provide authentication of DHCP messages
      (section 21)


6. Interaction with DHCP for Address Assignment

   In some networks, there may be both clients that are using stateless
   address autoconfiguration and DHCP for DNS configuration and clients
   that are using DHCP for stateful address configuration.  Depending on
   the deployment and configuration of relay agents, DHCP servers that
   are intended only for stateless configuration may receive messages
   from clients that are performing stateful address configuration.

   A DHCP server that is only able to provide stateless configuration
   information through an Information-request/Reply message exchange
   discards any other DHCP messages it receives. Specifically, the
   server discards any messages other than Information-Request or
   Relay-forward it receives, and the server does not participate in any
   stateful address configuration messages exchanges.  If there are
   other DHCP servers that are configured to provide stateful address
   assignment, one of those servers will provide the address assignment.

7. Security Considerations

   Stateless DHCP service is a proper subset of the DHCP service
   described in the DHCP specification, RFC 3315. Therefore, stateless
   DHCP service introduces no additional security considerations beyond



Droms                    Expires July 13, 2004                  [Page 6]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   those discussed in sections 21, 22.11 and 23 of the DHCP
   specification.

   Configuration information provided to a node through stateless DHCP
   service may be used to mount spoofing, man-in-the-middle,
   denial-of-service and other attacks. These attacks are described in
   more detail in the specifications for each of the options that carry
   configuration information. Authenticated DHCP, as described in
   sections 21 and 22.11 of the DHCP specification, can be used to avoid
   attacks mounted through the stateless DHCP service.

8. Acknowledgments

   Jim Bound, Ted Lemon and Bernie Volz reviewed this document and
   contributed editorial suggestions.  Thanks to Peter Barany, Tim
   Chown, Christian Huitema, Tatuya Jinmei, Pekka Savola and Juha
   Wiljakka for their review and comments.

Normative References

   [1]  Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C. and M.
        Carney, "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)",
        RFC 3315, July 2003.

   [2]  Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
        Specification", RFC 2460, December 1998.

Informative References

   [3]  Droms, R., "DNS Configuration options for Dynamic Host
        Configuration Protocol for IPv6 (DHCPv6)", RFC 3646, December
        2003.

   [4]  Narten, T., Nordmark, E. and W. Simpson, "Neighbor Discovery for
        IP Version 6 (IPv6)", RFC 2461, December 1998.

   [5]  Schulzrinne, H. and B. Volz, "Dynamic Host Configuration
        Protocol (DHCPv6) Options for Session Initiation Protocol (SIP)
        Servers", RFC 3319, July 2003.

   [6]  Thomson, S. and T. Narten, "IPv6 Stateless Address
        Autoconfiguration", RFC 2462, December 1998.

   [7]  Mockapetris, P., "Domain names - concepts and facilities", STD
        13, RFC 1034, November 1987.

   [8]  Aboba, B., "Detection of Network Attachment (DNA) in IPv4",
        draft-ietf-dhc-dna-ipv4-04 (work in progress), October 2003.



Droms                    Expires July 13, 2004                  [Page 7]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


Author's Address

   Ralph Droms
   Cisco Systems
   1414 Massachusetts Avenue
   Boxborough, MA  01719
   USA

   Phone: +1 978 497 4733
   EMail: rdroms@cisco.com









































Droms                    Expires July 13, 2004                  [Page 8]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


Intellectual Property Statement

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights. Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11. Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard. Please address the information to the IETF Executive
   Director.


Full Copyright Statement

   Copyright (C) The Internet Society (2004). All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works. However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assignees.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION



Droms                    Expires July 13, 2004                  [Page 9]


Internet-Draft    Stateless DHCPv6 Implementation Guide     January 2004


   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Acknowledgment

   Funding for the RFC Editor function is currently provided by the
   Internet Society.











































Droms                    Expires July 13, 2004                 [Page 10]