Dynamic Host Configuration (dhc) F. Gont
Internet-Draft SI6 Networks / UTN-FRH
Intended status: Standards Track W. Liu
Expires: August 22, 2015 Huawei Technologies
February 18, 2015
A Method for Generating Semantically Opaque Interface Identifiers with
Dynamic Host Configuration Protocol for IPv6 (DHCPv6)
draft-ietf-dhc-stable-privacy-addresses-01
Abstract
This document specifies a method for selecting IPv6 Interface
Identifiers, to be employed by Dynamic Host Configuration Protocol
for IPv6 (DHCPv6) servers when leasing non-temporary IPv6 addresses
to DHCPv6 clients. This method is a DHCPv6 server side algorithm,
that does not require any updates to the existing DHCPv6
specifications. The aforementioned method results in stable
addresses within each subnet, even in the presence of multiple DHCPv6
servers or DHCPv6 server reinstallments. It is a DHCPv6-variant of
the method specified in RFC 7217 for IPv6 Stateless Address
Autoconfiguration.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 22, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Gont & Liu Expires August 22, 2015 [Page 1]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Method Specification . . . . . . . . . . . . . . . . . . . . 3
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6
5. Security Considerations . . . . . . . . . . . . . . . . . . . 6
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.1. Normative References . . . . . . . . . . . . . . . . . . 7
7.2. Informative References . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
Stable IPv6 addresses tend to simplify event logging, trouble-
shooting, enforcement of access controls and quality of service, etc.
However, there are a number of scenarios in which a host employing
the DHCPv6 protocol [RFC3315] may be assigned different IPv6
addresses for the same interface within the same subnet over time.
For example, this may happen when multiple servers operate on the
same network to provide increased availability, but may also happen
as a result of DHCPv6 server reinstallments and other scenarios.
This document specifies a method for selecting IPv6 Interface
Identifiers, to be employed by Dynamic Host Configuration Protocol
for IPv6 (DHCPv6) servers when leasing non-temporary IPv6 addresses
to DHCPv6 clients (i.e., to be employed with IA_NA options). This
method is a DHCPv6 server side algorithm, that does not require any
updates to the existing DHCPv6 specifications. The aforementioned
method has the following properties:
o The resulting IPv6 addresses remain stable within each subnet for
the same network interface of the same client, even when different
DHCPv6 servers (implementing this specification) are employed.
o Predicting the IPv6 addresses that will be generated by the method
specified in this document, even with knowledge of the IPv6
addresses generated for other nodes within the same network,
becomes very difficult.
Gont & Liu Expires August 22, 2015 [Page 2]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
The method specified in this document achieves the aforementioned
properties by means of a calculated technique as opposed to e.g.
state- sharing among DHCPv6 servers. This approach has been already
suggested in [RFC7031]. We note that the method specified in this
document is essentially a DHCPv6-version of the "Method for
Generating Semantically Opaque Interface Identifiers with IPv6
Stateless Address Autoconfiguration (SLAAC)" specified in [RFC7217].
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Method Specification
DHCPv6 server implementations conforming to this specification MUST
generate non-temporary IPv6 addresses using the algorithm specified
in this section.
Implementations conforming to this specification SHOULD provide the
means for a system administrator to enable or disable the use of this
algorithm for generating IPv6 addresses.
All of the parameters included in the expression below MUST be
included when generating an IPv6 address.
A DHCPv6 server implementing this specification must select the IPv6
addresses to be leased with the following algorithm:
1. Compute a random (but stable) identifier with the expression:
RID = F(IPV6_ADDR_HI | IPV6_ADDR_LOW | Client_DUID | IAID |
Counter | secret_key)
Where:
RID:
Random (but stable) Identifier
F():
A pseudorandom function (PRF) that MUST NOT be computable from
the outside (without knowledge of the secret key). F() MUST
also be difficult to reverse, such that it resists attempts to
obtain the secret_key, even when given samples of the output
of F() and knowledge or control of the other input parameters.
F() SHOULD produce an output of at least 64 bits. F() could
be implemented as a cryptographic hash of the concatenation of
Gont & Liu Expires August 22, 2015 [Page 3]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
each of the function parameters. The default algorithm to be
employed for F() SHOULD be SHA-1 [FIPS-SHS]. An
implementation MAY provide the means for selecting other other
algorithms (e.g., SHA-256) for F(). Note: MD5 [RFC1321] is
considered unacceptable for F() [RFC6151].
|:
An operator representing "concatenation".
IPV6_ADDR_HI:
An IPv6 address specifying the upper boundary of the IPv6
address pool from which the DHCPv6 server leases IPv6
addresses. It MUST be represented as a 128-bit unsigned
integer in network byte order. If multiple servers operate on
the same network to provide increased availability, all such
DHCPv6 servers MUST be configured with the address range
(i.e., the same IPV6_ADDR_HI and IPV6_ADDR_LOW parameters).
It is the administrator's responsibility that the
aforementioned requirement is met.
IPV6_ADDR_LOW:
An IPv6 address specifying the lower boundary of the IPv6
address pool from which the DHCPv6 server leases IPv6
addresses. It MUST be represented as a 128-bit unsigned
integer in network byte order. If multiple servers operate on
the same network to provide increased availability, all such
DHCPv6 servers MUST be configured with the address range
(i.e., the same IPV6_ADDR_HI and IPV6_ADDR_LOW parameters).
It is the administrator's responsibility that the
aforementioned requirement is met.
Client_DUID:
The DUID value contained in the Client Identifier option
received in the DHCPv6 client message. The DUID can be
treated as an array of 8-bit unsigned integers.
IAID:
The IAID value contained in the IA_NA option received in the
client message. It MUST be interpreted as a 32-bit unsigned
integer in network byte order.
Counter:
A 32-bit unsigned integer in network byte order, that is
employed to resolve address conflicts. It MUST be initialized
to 0.
secret_key:
Gont & Liu Expires August 22, 2015 [Page 4]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
A secret key configured by the DHCPv6 server administrator,
which MUST NOT be known by the attacker. It MUST be encoded
as an array of 8-bit unsigned integers containing the ASCII
codes corresponding to the secret key. An implementation of
this specification MUST provide an interface for viewing and
changing the secret key. All DHCPv6 servers leasing addresses
from the same address range MUST employ the same secret key.
2. A candidate IPv6 address to be leased is obtained as follows:
IPV6_ADDRESS = IPV6_ADDR_LOW + RID % (IPV6_ADDR_HI -
IPV6_ADDR_LOW + 1)
We note that [RFC4291] requires that, the Interface IDs of all
unicast addresses (except those that start with the binary
value 000) be 64-bit long. The method discussed in this
document can be employed for generating IPv6 addresses for any
address range (e.g., smaller than 2**64 bits), albeit at the
expense of reduced entropy (when the address range is smaller
than than of a full 64-bit subnet).
3. The Interface Identifier of the selected IPv6 address MUST be
compared against the reserved IPv6 Interface Identifiers
[RFC5453] [IANA-RESERVED-IID]. In the event that an unacceptable
identifier has been generated, the Counter variable should be
incremented by 1, and a new IPv6 address (RID and subsequent
IPV6_ADDRESS) should be computed with the updated Counter value.
4. If the resulting address is not available (e.g., there is a
conflicting binding), the server should increment the Counter
variable, and a new Interface ID and IPv6 address should be
computed with the updated Counter value.
This document requires that SHA-1 be the default function to be used
for F(), such that, all other configuration parameters being the
same, different implementations of this specification result in the
same IPv6 addresses.
Including the address range in the PRF computation causes the
Interface Identifier to be different for each IPv6 address leased
from a different address range to the same client. This mitigates
the correlation of activities of multi-homed nodes (since each of the
corresponding addresses will employ a different Interface ID), host-
tracking (since the network prefix will change as the node moves from
one network to another), and any other attacks that benefit from
predictable Interface Identifiers (such as IPv6 address scanning
attacks) [I-D.ietf-6man-ipv6-address-generation-privacy].
Gont & Liu Expires August 22, 2015 [Page 5]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
As required by [RFC3315], an IAID is associated with each of the
client's network interfaces, and is consistent across restarts of the
DHCPv6 client.
The Counter parameter provides the means to intentionally cause this
algorithm to produce different IPv6 addresses (all other parameters
being the same). This could be necessary to resolve address
conflicts (e.g. the resulting address having a conflicting binding).
Note that the result of F() in the algorithm above is no more secure
than the secret key. If an attacker is aware of the PRF that is
being used by the DHCPv6 server (which we should expect), and the
attacker can obtain enough material (i.e. addresses generated by the
DHCPv6 server), the attacker may simply search the entire secret-key
space to find matches. To protect against this, the secret key
SHOULD be of at least 128 bits. Key lengths of at least 128 bits
should be adequate.
Providing a mechanism to display and change the secret_key is crucial
for having different DHCPv6 servers produce the same IPv6 addresses,
and for causing a replacement system to generate the same IPv6
addresses as the system being replaced. We note that since the
privacy of the scheme specified in this document relies on the
secrecy of the secret_key parameter, implementations should constrain
access to the secret_key parameter to the extent practicable (e.g.,
require superuser privileges to access it). Furthermore, in order to
prevent leakages of the secret_key parameter, it should not be used
for any other purposes than being a parameter to the scheme specified
in this document.
We note that all of the bits in the resulting Interface IDs are
treated as "opaque" bits [RFC7136]. For example, the universal/local
bit of Modified EUI-64 format identifiers is treated as any other bit
of such identifier.
4. IANA Considerations
There are no IANA registries within this document. The RFC-Editor
can remove this section before publication of this document as an
RFC.
5. Security Considerations
The method specified in this document results in IPv6 Interface
Identifiers (and hence IPv6 addresses) that do not follow any
specific pattern. Thus, address-scanning attacks
[I-D.ietf-opsec-ipv6-host-scanning] are mitigated.
Gont & Liu Expires August 22, 2015 [Page 6]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
The method specified in this document neither mitigates nor
exacerbates the security considerations for DHCPv6 discussed in
[RFC3315].
6. Acknowledgements
This document is based on [RFC7217], authored by Fernando Gont.
The authors would like to thank Stephane Bortzmeyer, Tatuya Jinmei,
Andre Kostur, Tomek Mrugalski, Hosnieh Rafiee, Jean-Francois
Tremblay, Tina Tsou, and Bernie Volz, for providing valuable comments
on earlier versions of this documents.
The authors would like to thank Ted Lemon, who kindly answered some
DHCPv6-related questions.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC5453] Krishnan, S., "Reserved IPv6 Interface Identifiers", RFC
5453, February 2009.
[RFC7136] Carpenter, B. and S. Jiang, "Significance of IPv6
Interface Identifiers", RFC 7136, February 2014.
7.2. Informative References
[FIPS-SHS]
FIPS, , "Secure Hash Standard (SHS)", Federal Information
Processing Standards Publication 180-4, March 2012,
<http://csrc.nist.gov/publications/fips/fips180-4/
fips-180-4.pdf>.
Gont & Liu Expires August 22, 2015 [Page 7]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
[I-D.ietf-6man-ipv6-address-generation-privacy]
Cooper, A., Gont, F., and D. Thaler, "Privacy
Considerations for IPv6 Address Generation Mechanisms",
draft-ietf-6man-ipv6-address-generation-privacy-03 (work
in progress), January 2015.
[I-D.ietf-opsec-ipv6-host-scanning]
Gont, F. and T. Chown, "Network Reconnaissance in IPv6
Networks", draft-ietf-opsec-ipv6-host-scanning-06 (work in
progress), February 2015.
[IANA-RESERVED-IID]
Reserved IPv6 Interface Identifiers, ,
"http://www.iana.org/assignments/ipv6-interface-ids/
ipv6-interface-ids.xml", .
[RFC1321] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321,
April 1992.
[RFC6151] Turner, S. and L. Chen, "Updated Security Considerations
for the MD5 Message-Digest and the HMAC-MD5 Algorithms",
RFC 6151, March 2011.
[RFC7031] Mrugalski, T. and K. Kinnear, "DHCPv6 Failover
Requirements", RFC 7031, September 2013.
[RFC7217] Gont, F., "A Method for Generating Semantically Opaque
Interface Identifiers with IPv6 Stateless Address
Autoconfiguration (SLAAC)", RFC 7217, April 2014.
Authors' Addresses
Fernando Gont
SI6 Networks / UTN-FRH
Evaristo Carriego 2644
Haedo, Provincia de Buenos Aires 1706
Argentina
Phone: +54 11 4650 8472
Email: fgont@si6networks.com
URI: http://www.si6networks.com
Gont & Liu Expires August 22, 2015 [Page 8]
Internet-Draft Stable and Opaque IIDs with DHCPv6 February 2015
Will(Shucheng) Liu
Huawei Technologies
Bantian, Longgang District
Shenzhen 518129
P.R. China
Email: liushucheng@huawei.com
Gont & Liu Expires August 22, 2015 [Page 9]