DMM Working Group                                          S. Matsushima
Internet-Draft                                                  SoftBank
Intended status: Standards Track                                L. Bertz
Expires: December 20, 2018                                        Sprint
                                                              M. Liebsch
                                                                     NEC
                                                           S. Gundavelli
                                                                   Cisco
                                                                D. Moses
                                                       Intel Corporation
                                                              C. Perkins
                                                               Futurewei
                                                           June 18, 2018


       Protocol for Forwarding Policy Configuration (FPC) in DMM
                       draft-ietf-dmm-fpc-cpdp-12

Abstract

   This document describes a way, called Forwarding Policy Configuration
   (FPC) to manage the separation of data-plane and control-plane.  FPC
   defines a flexible mobility management system using FPC agent and FPC
   client functions.  A FPC agent provides an abstract interface to the
   data-plane.  The FPC client configures data-plane nodes by using the
   functions and abstractions provided by the FPC agent for the data-
   plane nodes.  The data-plane abstractions presented in this document
   are extensible in order to support many different types of mobility
   management systems and data-plane functions.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on December 20, 2018.





Matsushima, et al.      Expires December 20, 2018               [Page 1]


Internet-Draft              DMM FPC Protocol                   June 2018


Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
   3.  FPC Design Objectives and Deployment  . . . . . . . . . . . .   7
   4.  FPC Mobility Information Model  . . . . . . . . . . . . . . .   9
     4.1.  Model Notation and Conventions  . . . . . . . . . . . . .   9
     4.2.  Templates and Attributes  . . . . . . . . . . . . . . . .  12
     4.3.  Attribute-Expressions . . . . . . . . . . . . . . . . . .  13
     4.4.  Attribute Value Types . . . . . . . . . . . . . . . . . .  14
     4.5.  Namespace and Format  . . . . . . . . . . . . . . . . . .  14
     4.6.  Configuring Attribute Values  . . . . . . . . . . . . . .  15
     4.7.  Entity Configuration Blocks . . . . . . . . . . . . . . .  16
     4.8.  Information Model Checkpoint  . . . . . . . . . . . . . .  17
     4.9.  Information Model Components  . . . . . . . . . . . . . .  18
       4.9.1.  Topology Information Model  . . . . . . . . . . . . .  18
       4.9.2.  Service-Group . . . . . . . . . . . . . . . . . . . .  18
       4.9.3.  Domain Information Model  . . . . . . . . . . . . . .  20
       4.9.4.  DPN Information Model . . . . . . . . . . . . . . . .  20
       4.9.5.  Policy Information Model  . . . . . . . . . . . . . .  21
       4.9.6.  Mobility-Context Information Model  . . . . . . . . .  24
       4.9.7.  Monitor Information Model . . . . . . . . . . . . . .  26
   5.  Protocol  . . . . . . . . . . . . . . . . . . . . . . . . . .  27
     5.1.  Protocol Messages and Semantics . . . . . . . . . . . . .  27
       5.1.1.  Configure Message . . . . . . . . . . . . . . . . . .  30
       5.1.2.  Monitor Messages  . . . . . . . . . . . . . . . . . .  36
     5.2.  Protocol Operation  . . . . . . . . . . . . . . . . . . .  38
       5.2.1.  DPN Selection . . . . . . . . . . . . . . . . . . . .  38
       5.2.2.  Policy Creation and Installation  . . . . . . . . . .  41
       5.2.3.  Simple RPC Operation  . . . . . . . . . . . . . . . .  43
       5.2.4.  Policy and Mobility on the Agent  . . . . . . . . . .  51
       5.2.5.  Monitor Example . . . . . . . . . . . . . . . . . . .  53
   6.  Templates and Command Sets  . . . . . . . . . . . . . . . . .  55



Matsushima, et al.      Expires December 20, 2018               [Page 2]


Internet-Draft              DMM FPC Protocol                   June 2018


     6.1.  Monitor Configuration Templates . . . . . . . . . . . . .  55
     6.2.  Descriptor Templates  . . . . . . . . . . . . . . . . . .  56
     6.3.  Tunnel Templates  . . . . . . . . . . . . . . . . . . . .  59
     6.4.  Action Templates  . . . . . . . . . . . . . . . . . . . .  60
     6.5.  Quality of Service Action Templates . . . . . . . . . . .  61
     6.6.  PMIP Command-Set  . . . . . . . . . . . . . . . . . . . .  62
     6.7.  3GPP Specific Templates and Command-Set . . . . . . . . .  62
   7.  Implementation Status . . . . . . . . . . . . . . . . . . . .  64
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  68
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  69
   10. Work Team Participants  . . . . . . . . . . . . . . . . . . .  71
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  71
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  71
     11.2.  Informative References . . . . . . . . . . . . . . . . .  72
   Appendix A.  YANG Data Model for the FPC protocol . . . . . . . .  73
     A.1.  FPC YANG Model  . . . . . . . . . . . . . . . . . . . . .  75
     A.2.  FPC YANG Settings and Extensions Model  . . . . . . . . .  97
     A.3.  PMIP QoS Model  . . . . . . . . . . . . . . . . . . . . . 109
     A.4.  Traffic Selectors YANG Model  . . . . . . . . . . . . . . 117
     A.5.  RFC 5777 Classifier YANG Model  . . . . . . . . . . . . . 125
   Appendix B.  FPC YANG Tree Structure  . . . . . . . . . . . . . . 132
   Appendix C.  Change Log . . . . . . . . . . . . . . . . . . . . . 150
     C.1.  Changes since Version 09  . . . . . . . . . . . . . . . . 150
     C.2.  Changes since Version 10  . . . . . . . . . . . . . . . . 151
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . . 151

1.  Introduction

   This document describes Forwarding Policy Configuration (FPC), a
   system for managing the separation of control-plane and data-plane.
   FPC enables flexible mobility management using FPC client and FPC
   agent functions.  A FPC agent exports an abstract interface
   representing the data-plane.  To configure data-plane nodes and
   functions, the FPC client uses the interface to the data-plane
   offered by the FPC agent.

   Control planes of mobility management systems, or related
   applications which require data-plane control, can utilize the FPC
   client at various levels of abstraction.  FPC operations are capable
   of directly configuring a single Data-Plane Node (DPN), as well as
   multiple DPNs, as determined by the data-plane models exported by the
   FPC agent.

   A FPC agent represents the data-plane operation according to several
   basic information models.  A FPC agent also provides access to
   Monitors, which produce reports when triggered by events or FPC
   Client requests regarding Mobility Contexts, DPNs or the Agent.




Matsushima, et al.      Expires December 20, 2018               [Page 3]


Internet-Draft              DMM FPC Protocol                   June 2018


   To manage mobility sessions, the FPC client assembles applicable sets
   of forwarding policies from the data model, and configures them on
   the appropriate FPC Agent.  The Agent then renders those policies
   into specific configurations for each DPN at which mobile nodes are
   attached.  The specific protocols and configurations to configure a
   DPN from a FPC Agent are outside the scope of this document.

   A DPN is a logical entity that performs data-plane operations (packet
   movement and management).  It may represent a physical DPN unit, a
   sub-function of a physical DPN or a collection of physical DPNs
   (i.e., a "virtual DPN").  A DPN may be virtual -- it may export the
   FPC DPN Agent interface, but be implemented as software that controls
   other data-plane hardware or modules that may or may not be FPC-
   compliant.  In this document, DPNs are specified without regard for
   whether the implementation is virtual or physical.  DPNs are
   connected to provide mobility management systems such as access
   networks, anchors and domains.  The FPC agent interface enables
   establishment of a topology for the forwarding plane.

   When a DPN is mapped to physical data-plane equipment, the FPC client
   can have complete knowledge of the DPN architecture, and use that
   information to perform DPN selection for specific sessions.  On the
   other hand, when a virtual DPN is mapped to a collection of physical
   DPNs, the FPC client cannot select a specific physical DPN because it
   is hidden by the abstraction; only the FPC Agent can address the
   specific associated physical DPNs.  Network architects have the
   flexibility to determine which DPN-selection capabilities are
   performed by the FPC Agent (distributed) and which by the FPC client
   (centralized).  In this way, overlay networks can be configured
   without disclosing detailed knowledge of the underlying hardware to
   the FPC client and applications.

   The abstractions in this document are designed to support many
   different mobility management systems and data-plane functions.  The
   architecture and protocol design of FPC is not tied to specific types
   of access technologies and mobility protocols.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   Attribute Expression:   The definition of a template Property.  This
                           includes setting the type, current value,
                           default value and if the attribute is static,
                           i.e. can no longer be changed.




Matsushima, et al.      Expires December 20, 2018               [Page 4]


Internet-Draft              DMM FPC Protocol                   June 2018


   Domain:                 One or more DPNs that form a logical
                           partition of network resources (e.g., a data-
                           plane network under common network
                           administration).  A FPC client (e.g., a
                           mobility management system) may utilize a
                           single or multiple domains.

   DPN:                    A data-plane node (DPN) is capable of
                           performing data-plane features.  For example,
                           DPNs may be switches or routers, regardless
                           of whether they are realized as hardware or
                           purely in software.

   FPC Client:             A FPC Client is integrated with a mobility
                           management system or related application,
                           enabling control over forwarding policy,
                           mobility sessions and DPNs via a FPC Agent.

   Mobility Context:       A Mobility Context contains the data-plane
                           information necessary to efficiently send and
                           receive traffic from a mobile node.  This
                           includes policies that are created or
                           modified during the network's operation - in
                           most cases, on a per-flow or per session
                           basis.  A Mobility-Context represents the
                           mobility sessions (or flows) which are active
                           on a mobile node.  This includes associated
                           runtime attributes, such as tunnel endpoints,
                           tunnel identifiers, delegated prefix(es),
                           routing information, etc.  Mobility-Contexts
                           are associated to specific DPNs.  Some pre-
                           defined Policies may apply during mobility
                           signaling requests.  The Mobility Context
                           supplies information about the policy
                           settings specific to a mobile node and its
                           flows; this information is often quite
                           dynamic.

   Mobility Session:       Traffic to/from a mobile node that is
                           expected to survive reconnection events.

   Monitor:                A reporting mechanism for a list of events
                           that trigger notification messages from a FPC
                           Agent to a FPC Client.

   Policy:                 A Policy determines the mechanisms for
                           managing specific traffic flows or packets.
                           Policies specify QoS, rewriting rules for



Matsushima, et al.      Expires December 20, 2018               [Page 5]


Internet-Draft              DMM FPC Protocol                   June 2018


                           packet processing, etc.  A Policy consists of
                           one or more rules.  Each rule is composed of
                           a Descriptor and Actions.  The Descriptor in
                           a rule identifies packets (e.g., traffic
                           flows), and the Actions apply treatments to
                           packets that match the Descriptor in the
                           rule.  Policies can apply to Domains, DPNs,
                           Mobile Nodes, Service-Groups, or particular
                           Flows on a Mobile Node.

   Property:               An attribute-value pair for an instance of a
                           FPC entity.

   Service-Group:          A set of DPN interfaces that support a
                           specific data-plane purpose, e.g. inbound/
                           outbound, roaming, subnetwork with common
                           specific configuration, etc.

   Template:               A recipe for instantiating FPC entities.
                           Template definitions are accessible (by name
                           or by a key) in an indexed set.  A Template
                           is used to create specific instances (e.g.,
                           specific policies) by assigning appropriate
                           values into the Template definition via
                           Attribute Expression.

   Template Configuration  The process by which a Template is referenced
                           (by name or by key) and Attribute Expressions
                           are created that change the value, default
                           value or static nature of the Attribute, if
                           permitted.  If the Template is Extensible,
                           new attributes MAY be added.

   Tenant:                 An operational entity that manages mobility
                           management systems or applications which
                           require data-plane functions.  A Tenant
                           defines a global namespace for all entities
                           owned by the Tenant enabling its entities to
                           be used by multiple FPC Clients across
                           multiple FPC Agents.

   Topology:               The DPNs and the links between them.  For
                           example, access nodes may be assigned to a
                           Service-Group which peers to a Service-Group
                           of anchor nodes.






Matsushima, et al.      Expires December 20, 2018               [Page 6]


Internet-Draft              DMM FPC Protocol                   June 2018


3.  FPC Design Objectives and Deployment

   Using FPC, mobility control-planes and applications can configure
   DPNs to perform various mobility management roles as described in
   [I-D.ietf-dmm-deployment-models].  This fulfills the requirements
   described in [RFC7333].

   This document defines FPC Agent and FPC Client, as well as the
   information models that they use.  The attributes defining those
   models serve as the protocol elements for the interface between the
   FPC Agent and the FPC Client.

   Mobility control-plane applications integrate features offered by the
   FPC Client.  The FPC Client connects to FPC Agent functions.  The
   Client and the Agent communicate based on information models
   described in Section 4.  The models allow the control-plane to
   configure forwarding policies on the Agent for data-plane
   communications with mobile nodes.

   Once the Topology of DPN(s) and domains are defined on an Agent for a
   data plane, the DPNs in the topology are available for further
   configuration.  The FPC Agent connects those DPNs to manage their
   configurations.

   A FPC Agent configures and manages its DPN(s) according to forwarding
   policies requested and Attributes provided by the FPC Client.
   Configuration commands used by the FPC agent to configure its DPN
   node(s) may be specific to the DPN implementation; consequently the
   method by which the FPC Agent carries out the specific configuration
   for its DPN(s) is out of scope for this document.  Along with the
   data models, the FPC Client (on behalf of control-plane and
   applications) requests that the Agent configures Policies prior to
   the time when the DPNs start forwarding data for their mobility
   sessions.

   This architecture is illustrated in Figure 1.  A FPC Agent may be
   implemented in a network controller that handles multiple DPNs, or
   (more simply) an FPC Agent may itself be integrated into a DPN.

   This document does not specify a protocol for the FPC interface; it
   is out of scope.  However, an implementation must support the FPC
   transactions described in Section 5.









Matsushima, et al.      Expires December 20, 2018               [Page 7]


Internet-Draft              DMM FPC Protocol                   June 2018


                           +-------------------------+
                           | Mobility Control-Plane  |
                           |          and            |
                           |      Applications       |
                           |+-----------------------+|
                           ||      FPC Client       ||
                           |+----------^------------+|
                           +-----------|-------------+
               FPC interface protocol  |
                       +---------------+-----------------+
                       |                                 |
         Network       |                                 |
         Controller    |                      DPN        |
           +-----------|-------------+        +----------|---------+
           |+----------v------------+|        |+---------v--------+|
           ||   [Data-plane model]  ||        ||[Data-plane model]||
           ||       FPC Agent       ||        ||    FPC Agent     ||
           |+-----------------------+|        |+------------------+|
           |+------------+----------+|        |                    |
           ||SB Protocol |FPC Client||        |  DPN Configuration |
           ||   Modules  |  Module  ||        +--------------------+
           |+------^-----+----^-----+|
           +-------|----------|------+
                   |          |
         Other     |          | FPC interface
        southbound |          | protocol
         protocols |          |
                   |          +-----------------+
                   |                            |
       DPN         |                 DPN        |
        +----------|---------+       +----------|---------+
        |+---------v--------+|       |+---------v--------+|
        ||  Configuration   ||       ||[Data-plane model]||
        || Protocol module  ||       ||     FPC Agent    ||
        |+------------------+|       |+------------------+|
        |                    |       |                    |
        | DPN Configuration  |       |  DPN Configuration |
        +--------------------+       +--------------------+

         Figure 1: Reference Forwarding Policy Configuration (FPC)
                               Architecture

   The FPC architecture supports multi-tenancy; a FPC enabled data-plane
   supports tenants of multiple mobile operator networks and/or
   applications.  It means that the FPC Client of each tenant connects
   to the FPC Agent and it MUST partition namespace and data for their
   data-planes.  DPNs on the data-plane may fulfill multiple data-plane
   roles which are defined per session, domain and tenant.



Matsushima, et al.      Expires December 20, 2018               [Page 8]


Internet-Draft              DMM FPC Protocol                   June 2018


   Multi-tenancy permits the paritioning of data-plane entities as well
   as a common namespace requirement upon FPC Agents and Clients when
   they use the same Tenant for a common data-plane entity.

   FPC information models often configuration to fit the specific needs
   for DPN management of a mobile node's traffic.  The FPC interfaces in
   Figure 1 are the only interfaces required to handle runtime data in a
   Mobility Context.  The Topology and some Policy FPC models MAY be
   pre-configured; in that case real-time protocol exchanges are not
   required for them.

   The information model provides an extensibility mechanism through
   Templates that permits specialization for the needs of a particular
   vendor's equipment or future extension of the model presented in this
   specification.

4.  FPC Mobility Information Model

   The FPC information model includes the following components:

      DPN Information Model,
      Topology Information Model,
      Policy Information Model,
      Mobility-Context, and
      Monitor, as illustrated in Figure 2.

                   :
                   |
                   +-[FPC Mobility Information Model]
                   |          |
                   |          +-[Topology Information Model]
                   |          |
                   |          +-[Policy Information Model]
                   |          |
                   |          +-[Mobility-Context]
                   |          |
                   |          +-[Monitor]
                   |

                 Figure 2: FPC Information Model structure

4.1.  Model Notation and Conventions

   The following conventions are used to describe the FPC information
   models.

   Information model entities (e.g.  DPNs, Rules, etc.) are defined in a
   hierarchical notation where all entities at the same hierarchical



Matsushima, et al.      Expires December 20, 2018               [Page 9]


Internet-Draft              DMM FPC Protocol                   June 2018


   level are located on the same left-justified vertical position
   sequentially.  When entities are composed of sub-entities, the sub-
   entities appear shifted to the right, as shown in Figure 3.

                              |
                              +-[entity2]
                              |         +-[entity2.1]
                              |         +-[entity2.2]

                   Figure 3: Model Notation - An Example

   Some entities have one or more qualifiers placed on the right hand
   side of the element definition in angle-brackets.  Common types
   include:

   List:  A collection of entities (some could be duplicated)

   Set:  A nonempty collection of entities without duplications

   Name:  A human-readable string

   Key:  A unique value.  We distinguish 3 types of keys:

      U-Key:  A key unique across all Tenants.  U-Key spaces typically
         involve the use of registries or language specific mechanisms
         that guarantee universal uniqueness of values.

      G-Key:  A key unique within a Tenant

      L-Key:  A key unique within a local namespace.  For example, there
         may exist interfaces with the same name, e.g. "if0", in two
         different DPNs but there can only be one "if0" within each DPN
         (i.e. its local Interface-Key L-Key space).

   Each entity or attribute may be optional (O) or mandatory (M).
   Entities that are not marked as optional are mandatory.















Matsushima, et al.      Expires December 20, 2018              [Page 10]


Internet-Draft              DMM FPC Protocol                   June 2018


       The following example shows 3 entities:
           -- Entity1 is a globally unique key, and optionally can have
                      an associated Name
           -- Entity2 is a list
           -- Entity3 is a set and is optional
                      +
                      |
                      +-[entity1] <G-Key> (M), <Name> (O)
                      +-[entity2] <List>
                      +-[entity3] <Set> (O)
                      |
                      +

                                 Figure 4

   When expanding entity1 into a modeling language such as YANG it would
   result in two values: entity1-Key and entity1-Name.

   To encourage re-use, FPC defines indexed sets of various entity
   Templates.  Other model elements that need access to an indexed model
   entity contain an attribute which is always denoted as "entity-Key".
   When a Key attribute is encountered, the referencing model element
   may supply attribute values for use when the referenced entity model
   is instantiated.  For example: Figure 5 shows 2 entities:

      EntityA definition references an entityB model element.

      EntityB model elements are indexed by entityB-Key.

   Each EntityB model element has an entityB-Key which allows it to be
   uniquely identified, and a list of Attributes (or, alternatively, a
   Type) which specifies its form.  This allows a referencing entity to
   create an instance by supplying entityB-Values to be inserted, in a
   Settings container.

















Matsushima, et al.      Expires December 20, 2018              [Page 11]


Internet-Draft              DMM FPC Protocol                   June 2018


                           .
                           .
                           |
                           +-[entityA]
                           |      +-[entityB-Key]
                           |      +-[entityB-Values]
                           .
                           .
                           |
                           +-[entityB] <L-Key> (M) <Set>
                           |      +-[entityB-Type]
                           .
                           .

                    Figure 5: Indexed sets of entities

   Indexed sets are specified for each of the following kinds of
   entities:

      Domain (See Section 4.9.3)
      DPN (See Section 4.9.4)
      Policy (See Section 4.9.5)
      Rule (See Section 4.9.5)
      Descriptor (See Figure 12)
      Action (See Figure 12)
      Service-Group (See Section 4.9.2, and
      Mobility-Context (See Section 4.9.6)

   As an example, for a Domain entity, there is a corresponding
   attribute denoted as "Domain-Key" whose value can be used to
   determine a reference to the Domain.

4.2.  Templates and Attributes

   In order to simplify development and maintenance of the needed
   policies and other objects used by FPC, the Information Models which
   are presented often have attributes that are not initialized with
   their final values.  When an FPC entity is instantiated according to
   a template definition, specific values need to be configured for each
   such attribute.  For instance, suppose an entity Template has an
   Attribute named "IPv4-Address", and also suppose that a FPC Client
   instantiates the entity and requests that it be installed on a DPN.
   An IPv4 address will be needed for the value of that Attribute before
   the entity can be used.







Matsushima, et al.      Expires December 20, 2018              [Page 12]


Internet-Draft              DMM FPC Protocol                   June 2018


                        +-[Template] <U-Key, Name> (M) <Set>
                        |      +-[Attributes] <Set> (M)
                        |      +-[Extensible ~ FALSE]
                        |      +-[Entity-State ~ Initial]
                        |      +-[Version]

                        Figure 6: Template entities

   Attributes:  A set of Attribute names MAY be included when defining a
      Template for instantiating FPC entities.

   Extensible:  Determines whether or not entities instantiated from the
      Template can be extended with new non-mandatory Attributes not
      originally defined for the Template.  Default value is FALSE.  If
      a Template does not explicitly specify this attribute, the default
      value is considered to be in effect.

   Entity-State:  Either Initial, PartiallyConfigured, Configured, or
      Active.  Default value is Initial.  See Section 4.6 for more
      information about how the Entity-Status changes during the
      configuration steps of the Entity.

   Version:  Provides a version tag for the Template.

   The Attributes in an Entity Template may be either mandatory or non-
   mandatory.  Attribute values may also be associated with the
   attributes in the Entity Template.  If supplied, the value may be
   either assigned with a default value that can be reconfigured later,
   or the value can be assigned with a static value that cannot be
   reconfigured later (see Section 4.3).

   It is possible for a Template to provide values for all of its
   Attributes, so that no additional values are needed before the entity
   can made Active.  Any instantiation from a Template MUST have at
   least one Attribute in order to be a useful entity unless the
   Template has none.

4.3.  Attribute-Expressions

   The syntax of the Attribute definition is formatted to make it clear.
   For every Attribute in the Entity Template, six possibilities are
   specified as follows:

   '[Att-Name: ]'  Mandatory Attribute is defined, but template does not
      provide any configured value.

   '[Att-Name: Att-Value]'  Mandatory Attribute is defined, and has a
      statically configured value.



Matsushima, et al.      Expires December 20, 2018              [Page 13]


Internet-Draft              DMM FPC Protocol                   June 2018


   '[Att-Name: ~ Att-Value]'  Mandatory Attribute is defined, and has a
      default value.

   '[Att-Name]'  Non-mandatory Attribute may be included but template
      does not provide any configured value.

   '[Att-Name = Att-Value]'  Non-mandatory Attribute may be included and
      has a statically configured value.

   '[Att-Name ~ Att-Value]'  Non-mandatory Attribute may be included and
      has a default value.

   So, for example, a default value for a non-mandatory IPv4-Address
   attribute would be denoted by [IPv4-Address ~ 127.0.0.1].

   After a FPC Client identifies which additional Attributes have been
   configured to be included in an instantiated entity, those configured
   Attributes MUST NOT be deleted by the FPC Agent.  Similarly, any
   statically configured value for an entity Attribute MUST NOT be
   changed by the FPC Agent.

   Whenever there is danger of confusion, the fully qualified Attribute
   name MUST be used when supplying needed Attribute Values for a
   structured Attribute.

4.4.  Attribute Value Types

   For situations in which the type of an attribute value is required,
   the following syntax is recommended.  To declare than an attribute
   has data type "foo", typecast the attribute name by using the
   parenthesized data type (foo).  So, for instance, [(float) Max-
   Latency-in-ms:] would indicate that the mandatory Attribute "Max-
   Latency-in-ms" requires to be configured with a floating point value
   before the instantiated entity could be used.  Similarly, [(float)
   Max-Latency-in-ms: 9.5] would statically configure a floating point
   value of 9.5 to the mandatory Attribute "Max-Latency-in-ms".

4.5.  Namespace and Format

   The identifiers and names in FPC models which reside in the same
   Tenant must be unique.  That uniqueness must be maintained by all
   Clients, Agents and DPNs that support the Tenant.  The Tenant
   namespace uniqueness MUST be applied to all elements of the tenant
   model, i.e.  Topology, Policy and Mobility models.

   When a Policy needs to be applied to Mobility-Contexts in all Tenants
   on an Agent, the Agent SHOULD define that policy to be visible by all
   Tenants.  In this case, the Agent assigns a unique identifier in the



Matsushima, et al.      Expires December 20, 2018              [Page 14]


Internet-Draft              DMM FPC Protocol                   June 2018


   Agent namespace and copies the values to each Tenant.  This
   effectively creates a U-Key although only a G-Key is required within
   the Tenant.

   The notation for identifiers can utilize any format with agreement
   between data-plane agent and client operators.  The formats include
   but are not limited to Globally Unique IDentifiers (GUIDs),
   Universally Unique IDentifiers (UUIDs), Fully Qualified Domain Names
   (FQDNs), Fully Qualified Path Names (FQPNs) and Uniform Resource
   Identifiers (URIs).  The FPC model does not limit the format, which
   could dictate the choice of FPC protocol.  Nevertheless, the
   identifiers which are used in a Mobility model should be considered
   to efficiently handle runtime parameters.

   There are identifiers reserved for Protocol Operation.  See
   Section 5.1.1.5 for details.

4.6.  Configuring Attribute Values

   Attributes of Information Model components such as policy templates
   are configured with values as part of FPC configuration operations.
   There may be several such configuration operations before the
   template instantiation is fully configured.

   Entity-Status indicates when an Entity is usable within a DPN.  This
   permits DPN design tradeoffs amongst local storage (or other
   resources), over the wire request size and the speed of request
   processing.  For example, DPN designers with constrained systems MAY
   only house entities whose status is Active which may result in
   sending over all policy information with a Mobility-Context request.
   Storing information elements with an entity status of
   "PartiallyConfigured" on the DPN requires more resources but can
   result in smaller over the wire FPC communication and request
   processing efficiency.

   When the FPC Client instantiates a Policy from a Template, the
   Policy-Status is "Initial".  When the FPC Client sends the policy to
   a FPC Agent for installation on a DPN, the Client often will
   configure appropriate attribute values for the installation, and
   accordingly changes the Policy-Status to "PartiallyConfigured" or
   "Configured".  The FPC Agent will also configure Domain-specific
   policies and DPN-specific policies on the DPN.  When configured to
   provide particular services for mobile nodes, the FPC Agent will
   apply whatever service-specific policies are needed on the DPN.  When
   a mobile node attaches to the network data-plane within the topology
   under the jurisdiction of a FPC Agent, the Agent may apply policies
   and settings as appropriate for that mobile node.  Finally, when the
   mobile node launches new flows, or quenches existing flows, the FPC



Matsushima, et al.      Expires December 20, 2018              [Page 15]


Internet-Draft              DMM FPC Protocol                   June 2018


   Agent, on behalf of the FPC Client, applies or deactivates whatever
   policies and attribute values are appropriate for managing the flows
   of the mobile node.  When a "Configured" policy is de-activated,
   Policy-Status is changed to be "Active".  When an "Active" policy is
   activated, Policy-Status is changed to be "Configured".

   Attribute values in DPN resident Policies may be configured by the
   FPC Agent as follows:

   Domain-Policy-Configuration:  Values for Policy attributes that are
      required for every DPN in the domain.

   DPN-Policy-Configuration:  Values for Policy attributes that are
      required for every policy configured on this DPN.

   Service-Group-Policy-Configuration:  Values for Policy attributes
      that are required to carry out the intended Service of the Service
      Group.

   MN-Policy-Configuration:  Values for Policy attributes that are
      required for all traffic to/from a particular mobile node.

   Service-Data-Flow-Policy-Configuration:  Values for Policy attributes
      that are required for traffic belonging to a particular set of
      flows on the mobile node.

   Any configuration changes MAY also supply updated values for existing
   default attribute values that may have been previously configured on
   the DPN resident policy.

   Entity blocks describe the format of the policy configurations.

4.7.  Entity Configuration Blocks

   As described in Section 4.6, a Policy Template may be configured in
   several stages by configuring default or missing values for
   Attributes that do not already have statically configured values.  A
   Policy-Configuration is the combination of a Policy-Key (to identify
   the Policy Template defining the Attributes) and the currently
   configured Attribute Values to be applied to the Policy Template.
   Policy-Configurations MAY add attributes to a Template if Extensible
   is True.  They MAY also refine existing attributes by:

      assign new values if the Attribute is not static

      make attributes static if they were not

      make an attribute mandatory



Matsushima, et al.      Expires December 20, 2018              [Page 16]


Internet-Draft              DMM FPC Protocol                   June 2018


   A Policy-Configuration MUST NOT define or refine an attribute twice.
   More generally, an Entity-Configuration can be defined for any
   configurable Indexed Set to be the combination of the Entity-Key
   along with a set of Attribute-Expressions that supply configuration
   information for the entity's Attributes.  Figure 7 shows a schematic
   representation for such Entity Configuration Blocks.

                   [Entity Configuration Block]
                   |       +-[Entity-Key] (M)
                   |       +-[Attribute-Expression] <Set> (M)

                   Figure 7: Entity Configuration Block

   This document makes use of the following kinds of Entity
   Configuration Blocks:

      Descriptor-Configuration

      Action-Configuration

      Rule-Configuration

      Interface-Configuration

      Service-Group-Configuration

      Domain-Policy-Configuration

      DPN-Policy-Configuration

      Policy-Configuration

      MN-Policy-Configuration

      Service-Data-Flow-Policy-Configuration

4.8.  Information Model Checkpoint

   The Information Model Checkpoint permits Clients and Tenants with
   common scopes, referred to in this specification as Checkpoint
   BaseNames, to track the state of provisioned information on an Agent.
   The Agent records the Checkpoint BaseName and Checkpoint value set by
   a Client.  When a Client attaches to the Agent it can query to
   determine the amount of work that must be executed to configure the
   Agent to a specific BaseName / checkpoint revision.

   Checkpoints are defined for the following information model
   components:



Matsushima, et al.      Expires December 20, 2018              [Page 17]


Internet-Draft              DMM FPC Protocol                   June 2018


      Service-Group

      DPN Information Model

      Domain Information Model

      Policy Information Model

4.9.  Information Model Components

4.9.1.  Topology Information Model

   The Topology structure specifies DPNs and the communication paths
   between them.  A network management system can use the Topology to
   select the most appropriate DPN resources for handling specific
   session flows.

   The Topology structure is illustrated in Figure 8 (for definitions
   see Section 2):

                         |
                         +-[Topology Information Model]
                         |          +-[Extensible: FALSE]
                         |          +-[Service-Group]
                         |          +-[DPN] <Set>
                         |          +-[Domain] <Set>

                       Figure 8: Topology Structure

4.9.2.  Service-Group

   Service-Group-Set is collection of DPN interfaces serving some data-
   plane purpose including but not limited to DPN Interface selection to
   fulfill a Mobility-Context.  Each Group contains a list of DPNs
   (referenced by DPN-Key) and selected interfaces (referenced by
   Interface-Key).  The Interfaces are listed explicitly (rather than
   referred implicitly by its specific DPN) so that every Interface of a
   DPN is not required to be part of a Group.  The information provided
   is sufficient to ensure that the Protocol, Settings (stored in the
   Service-Group-Configuration) and Features relevant to successful
   interface selection is present in the model.










Matsushima, et al.      Expires December 20, 2018              [Page 18]


Internet-Draft              DMM FPC Protocol                   June 2018


   |
   +-[Service-Group] <G-Key>, <Name> (O) <Set>
   |           +-[Extensible: FALSE]
   |           +-[Role] <U-Key>
   |           +-[Protocol] <Set>
   |           +-[Feature] <Set> (O)
   |           +-[Service-Group-Configuration] <Set> (O)
   |           +-[DPN-Key] <Set>
   |           |           +-[Referenced-Interface] <Set>
   |           |           |       +-[Interface-Key] <L-Key>
   |           |           |       +-[Peer-Service-Group-Key] <Set> (O)

                          Figure 9: Service Group

   Each Service-Group element contains the following information:

   Service-Group-Key:  A unique ID of the Service-Group.

   Service-Group-Name:  A human-readable display string.

   Role:  The role (MAG, LMA, etc.) of the device hosting the interfaces
      of the DPN Group.

   Protocol-Set:  The set of protocols supported by this interface
      (e.g., PMIP, S5-GTP, S5-PMIP etc.).  The protocol MAY be only its
      name, e.g. 'gtp', but many protocols implement specific message
      sets, e.g. s5-pmip, s8-pmip.  When the Service-Group supports
      specific protocol message sub-subsets the Protocol value MUST
      include this information.

   Feature-Set:  An optional set of static features which further
      determine the suitability of the interface to the desired
      operation.

   Service-Group-Configuration-Set:  An optional set of configurations
      that further determine the suitability of an interface for the
      specific request.  For example: SequenceNumber=ON/OFF.

   DPN-Key-Set:  A key used to identify the DPN.

   Referenced-Interface-Set:  The DPN Interfaces and peer Service-Groups
      associated with them.  Each entry contains

      Interface-Key:   A key that is used together with the DPN-Key, to
         create a key that is refers to a specific DPN interface
         definition.





Matsushima, et al.      Expires December 20, 2018              [Page 19]


Internet-Draft              DMM FPC Protocol                   June 2018


      Peer-Service-Group-Key:   Enables location of the peer Service-
         Group for this Interface.

4.9.3.  Domain Information Model

   A Domain-Set represents a group of heterogeneous Topology resources
   typically sharing a common administrative authority.  Other models,
   outside of the scope of this specification, provide the details for
   the Domain.

             |
             +-[Domain] <G-Key>, <Name> (O) <Set>
             |       +-[Domain-Policy-Configuration] (O) <Set>
             |

                    Figure 10: Domain Information Model

   Each Domain entry contains the following information:

   Domain-Key:  Identifies and enables reference to the Domain.

   Domain-Name:  A human-readable display string naming the Domain.

4.9.4.  DPN Information Model

   A DPN-Set contains some or all of the DPNs in the Tenant's network.
   Some of the DPNs in the Set may be identical in functionality and
   only differ by their Key.

               |
               +-[DPN] <G-Key>, <Name> (O) <Set>
               |     +-[Extensible: FALSE]
               |     +-[Interface] <L-Key> <Set>
               |     |      +-[Role] <U-Key>
               |     |      +-[Protocol] <Set>
               |     |      +-[Interface-Configuration] <Set> (O)
               |     +-[Domain-Key]
               |     +-[Service-Group-Key] <Set> (O)
               |     +-[DPN-Policy-Configuration] <List> (M)
               |     +-[DPN-Resource-Mapping-Reference] (O)

                     Figure 11: DPN Information Model

   Each DPN entry contains the following information:

   DPN-Key:  A unique Identifier of the DPN.

   DPN-Name:  A human-readable display string.



Matsushima, et al.      Expires December 20, 2018              [Page 20]


Internet-Draft              DMM FPC Protocol                   June 2018


   Domain-Key:  A Key providing access to the Domain information about
      the Domain in which the DPN resides.

   Interface-Set:  The Interface-Set references all interfaces (through
      which data packets are received and transmitted) available on the
      DPN.  Each Interface makes use of attribute values that are
      specific to that interface, for example, the MTU size.  These do
      not affect the DPN selection of active or enabled interfaces.
      Interfaces contain the following information:

      Role:   The role (MAG, LMA, PGW, AMF, etc.) of the DPN.

      Protocol (Set):  The set of protocols supported by this interface
         (e.g., PMIP, S5-GTP, S5-PMIP etc.).  The protocol MAY implement
         specific message sets, e.g. s5-pmip, s8-pmip.  When a protocol
         implements such message sub-subsets the Protocol value MUST
         include this information.

      Interface-Configuration-Set:  Configurable settings that further
         determine the suitability of an interface for the specific
         request.  For example: SequenceNumber=ON/OFF.

   Service-Group-Set:  The Service-Group-Set references all of the
      Service-Groups which have been configured using Interfaces hosted
      on this DPN.  The purpose of a Service-Group is not to describe
      each interface of each DPN, but rather to indicate interface types
      for use during the DPN selection process, when a DPN with specific
      interface capabilities is required.

   DPN-Policy-Configuration:  A list of Policies that have been
      configured on this DPN.  Some may have values for all attributes,
      and some may require further configuration.  Each Policy-
      Configuration has a key to enable reference to its Policy-
      Template.  Each Policy-Configuration also has been configured to
      supply missing and non-default values to the desired Attributes
      defined within the Policy-Template.

   DPN-Resource-Mapping-Reference (O):  A reference to the underlying
      implementation, e.g. physical node, software module, etc. that
      supports this DPN.  Further specification of this attribute is out
      of scope for this document.

4.9.5.  Policy Information Model

   The Policy Information Model defines and identifies Rules for
   enforcement at DPNs.  A Policy is basically a set of Rules that are
   to be applied to each incoming or outgoing packet at a DPN interface.
   Rules comprise Descriptors and a set of Actions.  The Descriptors,



Matsushima, et al.      Expires December 20, 2018              [Page 21]


Internet-Draft              DMM FPC Protocol                   June 2018


   when evaluated, determine whether or not a set of Actions will be
   performed on the packet.  The Policy structure is independent of a
   policy context.

   In addition to the Policy structure, the Information Model (per
   Section 4.9.6) defines Mobility-Context.  Each Mobility-Context may
   be configured with appropriate Attribute values, for example
   depending on the identity of a mobile node.

   Traffic descriptions are defined in Descriptors, and treatments are
   defined separately in Actions.  A Rule-Set binds Descriptors and
   associated Actions by reference, using Descriptor-Key and Action-Key.
   A Rule-Set is bound to a policy in the Policy-Set (using Policy-Key),
   and the Policy references the Rule definitions (using Rule-Key).

              |
              +-[Policy Information Model]
              |      +-[Extensible:]
              |      +-[Policy-Template] <G-Key> (M) <Set>
              |      |       +-[Policy-Configuration] <Set> (O)
              |      |       +-[Rule-Template-Key] <List> (M)
              |      |       |       +-[Precedence] (M)
              |      +-[Rule-Template] <L-Key> (M) <Set>
              |      |       +-[Descriptor-Match-Type] (M)
              |      |       +-[Descriptor-Configuration] <Set> (M)
              |      |       |       +-[Direction] (O)
              |      |       +-[Action-Configuration] <Set> (M)
              |      |       |       +-[Action-Order] (M)
              |      |       +-[Rule-Configuration] (O)
              |      +-[Descriptor-Template] <L-Key> (M) <Set>
              |      |       +-[Descriptor-Type] (O)
              |      |       +-[Attribute-Expression] <Set> (M)
              |      +-[Action-Template] <L-Key> (M) <Set>
              |              +-[Action-Type] (O)
              |      |       +-[Attribute-Expression] <Set> (M)

                    Figure 12: Policy Information Model

   The Policy structure defines Policy-Set, Rule-Set, Descriptor-Set,
   and Action-Set, as follows:

   Policy-Template: <Set>  A set of Policy structures, indexed by
      Policy-Key, each of which is determined by a list of Rules
      referenced by their Rule-Key.  Each Policy structure contains the
      following:

      Policy-Key:   Identifies and enables reference to this Policy
         definition.



Matsushima, et al.      Expires December 20, 2018              [Page 22]


Internet-Draft              DMM FPC Protocol                   June 2018


      Rule-Template-Key:   Enables reference to a Rule template
         definition.

      Rule-Precedence:   For each Rule identified by a Rule-Template-Key
         in the Policy, specifies the order in which that Rule must be
         applied.  The lower the numerical value of Precedence, the
         higher the rule precedence.  Rules with equal precedence MAY be
         executed in parallel if supported by the DPN.  If this value is
         absent, the rules SHOULD be applied in the order in which they
         appear in the Policy.

   Rule-Template-Set:   A set of Rule Template definitions indexed by
      Rule-Key.  Each Rule is defined by a list of Descriptors (located
      by Descriptor-Key) and a list of Actions (located by Action-Key)
      as follows:

      Rule-Template-Key:   Identifies and enables reference to this Rule
         definition.

      Descriptor-Match-Type  Indicates whether the evaluation of the
         Rule proceeds by using conditional-AND, or conditional-OR, on
         the list of Descriptors.

      Descriptor-Configuration:   References a Descriptor template
         definition, along with an expression which names the Attributes
         for this instantiation from the Descriptor-Template and also
         specifies whether each Attribute of the Descriptor has a
         default value or a statically configured value, according to
         the syntax specified in Section 4.2.

      Direction:   Indicates if a rule applies to uplink traffic, to
         downlink traffic, or to both uplink and downlink traffic.
         Applying a rule to both uplink and downlink traffic, in case of
         symmetric rules, eliminates the requirement for a separate
         entry for each direction.  When not present, the direction is
         implied by the Descriptor's values.

      Action-Configuration:   References an Action Template definition,
         along with an expression which names the Attributes for this
         instantiation from the Action-Template and also specifies
         whether each Attribute of the Action has a default value or a
         statically configured value, according to the syntax specified
         in Section 4.2.

      Action-Order:   Defines the order in which actions are executed
         when the associated traffic descriptor selects the packet.





Matsushima, et al.      Expires December 20, 2018              [Page 23]


Internet-Draft              DMM FPC Protocol                   June 2018


   Descriptor-Template-Set:   A set of traffic Descriptor Templates,
      each of which can be evaluated on the incoming or outgoing packet,
      returning a TRUE or FALSE value, defined as follows:

      Descriptor-Template-Key:   Identifies and enables reference to
         this descriptor template definition.

      Attribute-Expression:  An expression which defines an Attribute in
         the Descriptor-Template and also specifies whether the Template
         also defines a default value or a statically configured value
         for the Attribute of the Descriptor has, according to the
         syntax specified in Section 4.2.

      Descriptor-Type:   Identifies the type of descriptor, e.g. an IPv6
         traffic selector per [RFC6088].

   Action-Template-Set:   A set of Action Templates defined as follows:

      Action-Template-Key:   Identifies and enables reference to this
         action template definition.

      Attribute-Expression:  An expression which defines an Attribute in
         the Action-Template and also specifies whether the Template
         also defines a default value or a statically configured value
         for the Attribute of the Action has, according to the syntax
         specified in Section 4.2.

      Action-Type:   Identifies the type of an action for unambiguous
         interpretation of an Action-Value entry.

4.9.6.  Mobility-Context Information Model

   The Mobility-Context structure holds entries associated with a mobile
   node and its mobility sessions (flows).  It is created on a DPN
   during the mobile node's registration to manage the mobile node's
   flows.  Flow information is added or deleted from the Mobility-
   Context as needed to support new flows or to deallocate resources for
   flows that are deactivated.  Descriptors are used to characterize the
   nature and resource requirement for each flow.

   Termination of a Mobility-Context implies termination of all flows
   represented in the Mobility-Context, e.g. after deregistration of a
   mobile node.  If any Child-Contexts are defined, they are also
   terminated.







Matsushima, et al.      Expires December 20, 2018              [Page 24]


Internet-Draft              DMM FPC Protocol                   June 2018


        +-[Mobility-Context] <G-Key> <Set>
        |            +-[Extensible:~ FALSE]
        |            +-[Delegating-IP-Prefix:] <Set> (O)
        |            +-[Parent-Context] (O)
        |            +-[Child-Context] <Set> (O)
        |            +-[Service-Group-Key] <Set> (O)
        |            +-[Mobile-Node]
        |            |       +-[IP-Address] <Set> (O))
        |            |       +-[MN-Policy-Configuration] <Set>
        |            +-[Domain-Key]
        |            |       +-[Domain-Policy-Configuration] <Set>
        |            +-[DPN-Key] <Set>
        |            |       +-[Role]
        |            |       +-[DPN-Policy-Configuration] <Set>
        |            |       +-[ServiceDataFlow] <L-Key> <Set> (O)
        |            |       |       +-[Service-Group-Key] (O)
        |            |       |       +-[Interface-Key] <Set>
        |            |       |       +-[ServiceDataFlow-Policy-
                                           Configuration] <Set> (O)
        |            |       |       |       +-[Direction]

               Figure 13: Mobility-Context Information Model

   The Mobility-Context Substructure holds the following entries:

   Mobility-Context-Key:   Identifies a Mobility-Context

   Delegating-IP-Prefix-Set:   Delegated IP Prefixes assigned to the
      Mobility-Context

   Parent-Context:   If present, a Mobility Context from which the
      Attributes and Attribute Values of this Mobility Context are
      inherited.

   Child-Context-Set:   A set of Mobility Contexts which inherit the
      Attributes and Attribute Values of this Mobility Context.

   Service-Group-Key:   Service-Group(s) used during DPN assignment and
      re-assignment.

   Mobile-Node:   Attributes specific to the Mobile Node.  It contains
      the following

      IP-Address-Set  IP addresses assigned to the Mobile Node.

      MN-Policy-Configuration-Set  For each MN-Policy in the set, a key
         and relevant information for the Policy Attributes.




Matsushima, et al.      Expires December 20, 2018              [Page 25]


Internet-Draft              DMM FPC Protocol                   June 2018


   Domain-Key:   Enables access to a Domain instance.

   Domain-Policy-Configuration-Set:   For each Domain-Policy in the set,
      a key and relevant information for the Policy Attributes.

   DPN-Key-Set:   Enables access to a DPN instance assigned to a
      specific role, i.e. this is a Set that uses DPN-Key and Role as a
      compound key to access specific set instances.

   Role:   Role this DPN fulfills in the Mobility-Context.

   DPN-Policy-Configuration-Set:   For each DPN-Policy in the set, a key
      and relevant information for the Policy Attributes.

   ServiceDataFlow-Key-Set:   Characterizes a traffic flow that has been
      configured (and provided resources) on the DPN to support data-
      plane traffic to and from the mobile device.

      Service-Group-Key:   Enables access to a Service-Group instance.

      Interface-Key-Set:   Assigns the selected interface of the DPN.

      ServiceDataFlow-Policy-Configuration-Set:   For each Policy in the
         set, a key and relevant information for the Policy Attributes.

         Direction:   Indicates if the reference Policy applies to
            uplink or downlink traffic, or to both, uplink- and downlink
            traffic.  Applying a rule to both, uplink- and downlink
            traffic, in case of symmetric rules, allows omitting a
            separate entry for each direction.  When not present the
            value is assumed to apply to both directions.

4.9.7.  Monitor Information Model

   Monitors provide a mechanism to produce reports when events occur.  A
   Monitor will have a target that specifies what is to be watched.

   The attribute/entity to be monitored places certain constraints on
   the configuration that can be specified.  For example, a Monitor
   using a Threshold configuration cannot be applied to a Mobility-
   Context, because it does not have a threshold.  Such a monitor
   configuration could be applied to a numeric threshold property of a
   Context.








Matsushima, et al.      Expires December 20, 2018              [Page 26]


Internet-Draft              DMM FPC Protocol                   June 2018


                           |
                           +-[Monitor] <G-Key> <List>
                           |         +-[Extensible:]
                           |         +-[Target:]
                           |         +-[Deferrable]
                           |         +-[Configuration]

                      Figure 14: Monitor Substructure

   Monitor-Key:  Identifies the Monitor.

   Target:  Description of what is to be monitored.  This can be a
      Service Data Flow, a Policy installed upon a DPN, values of a
      Mobility-Context, etc.  The target name is the absolute
      information model path (separated by '/') to the attribute /
      entity to be monitored.

   Deferrable:   Indicates that a monitoring report can be delayed up to
      a defined maximum delay, set in the Agent, for possible bundling
      with other reports.

   Configuration:  Determined by the Monitor subtype.  The monitor
      report is specified by the Configuration.  Four report types are
      defined:

      *  "Periodic" reporting specifies an interval by which a
         notification is sent.

      *  "Event-List" reporting specifies a list of event types that, if
         they occur and are related to the monitored attribute, will
         result in sending a notification.

      *  "Scheduled" reporting specifies the time (in seconds since Jan
         1, 1970) when a notification for the monitor should be sent.
         Once this Monitor's notification is completed the Monitor is
         automatically de-registered.

      *  "Threshold" reporting specifies one or both of a low and high
         threshold.  When these values are crossed a corresponding
         notification is sent.

5.  Protocol

5.1.  Protocol Messages and Semantics

   Four Client to Agent messages are supported.





Matsushima, et al.      Expires December 20, 2018              [Page 27]


Internet-Draft              DMM FPC Protocol                   June 2018


   +---------------------+---------------------------------------------+
   | Message             | Description                                 |
   +---------------------+---------------------------------------------+
   | Configure           | A Configure message includes multiple edits |
   |                     | to one or more information model entities.  |
   |                     | Edits are executed according to their Edit- |
   |                     | Id in ascending order.  The global status   |
   |                     | of the operation and the status of          |
   |                     | individual edits are returned. Partial      |
   |                     | failures, i.e. individual edit failures,    |
   |                     | are allowed.                                |
   | Register-Monitors   | Register monitors at an Agent. The message  |
   |                     | includes the Monitor information as         |
   |                     | specified in Section 4.9.7.                 |
   | Deregister-Monitors | Deregister monitors from an Agent. An       |
   |                     | optional boolean, Send-Data, indicates if a |
   |                     | successful deregistration triggers a Notify |
   |                     | with final data from the Agent for the      |
   |                     | corresponding Monitor.                      |
   | Probe               | Probe the status of registered monitors.    |
   |                     | This triggers a Notify with current data    |
   |                     | from the Agent for the corresponding        |
   |                     | Monitors.                                   |
   +---------------------+---------------------------------------------+

                     Table 1: Client to Agent Messages

   Each message contains a header with the following information:

   Client Identifier:  An Identifier used by the Agent to associate
       specific configuration characteristics, e.g. options used by the
       Client when communicating with the Agent, the association of the
       Client and tenant in the information model as well as tracking
       operations and notifications.

   Delay:  An optional time (in ms) to delay the execution of the
       operation on the DPN once it is received by the Agent.

   Operation Identifier:  A unique identifier created by the Client to
       correlate responses and notifications

   An Agent will respond with an ERROR, indicating one or more Errors
   have occurred, or an OK.

   For Configure messages, an OK status for an edit MAY include
   subsequent edits in the response that were required to properly
   execute the edit.  It MAY also indicate that the final status and any
   final edits required to fulfill the request will be sent via a



Matsushima, et al.      Expires December 20, 2018              [Page 28]


Internet-Draft              DMM FPC Protocol                   June 2018


   Configure Result Notification from the Agent to the Client, see
   Section 5.1.1.4.2.

   If errors occur, they MUST be returned as a list in responses and
   each Error contains the following information:

   Error-type:  The specific error type.  Values are TRANSPORT (0), RPC
       (1), PROTOCOL(2) or APPLICATION (3).

   Error-Tag:  An error tag.

   Error-App-Tag:  Application specific error tag.

   Error-Message:  A message describing the error.

   Error-Info:  Any data required for the response.

                         |
                         +-[Errors] <List>
                         |         +-[(Enumeration) Error-Type ]
                         |         +-[(String) Error-Tag ]
                         |         +-[(String) Error-App-Tag ] (O)
                         |         +-[(String) Error-Message ] (O)
                         |         +-[Error-Info] (O)

                    Figure 15: Error Information Model

   Two Agent to Client notifications are supported.

   +-------------------------------+-----------------------------------+
   | Message                       | Description                       |
   +-------------------------------+-----------------------------------+
   | Configure-Result-Notification | An asynchronous notification from |
   |                               | Agent to Client based upon a      |
   |                               | previous Configure request.       |
   | Notify                        | An asynchronous notification from |
   |                               | Agent to Client based upon a      |
   |                               | registered Monitor's              |
   |                               | configuration, a Monitor          |
   |                               | deregistration or Probe.          |
   +-------------------------------+-----------------------------------+

             Table 2: Agent to Client Messages (notifications)








Matsushima, et al.      Expires December 20, 2018              [Page 29]


Internet-Draft              DMM FPC Protocol                   June 2018


5.1.1.  Configure Message

   The Configure message follows edit formats proposed by [RFC8072] with
   more fields in each edit, an extra operation (clone) and a different
   response format.

5.1.1.1.  Edit Operation Types

   +-----------+-------------------------------------------------------+
   | Operation | Description                                           |
   +-----------+-------------------------------------------------------+
   | create    | Creates a new data resource or Entity.  If the        |
   |           | resource exists an error is returned.                 |
   | delete    | Deletes a resource.  If it does not exist an error is |
   |           | returned.                                             |
   | insert    | Inserts data in a list or user ordered list.          |
   | merge     | Merges the edit value with the target data resource;  |
   |           | the resource is created if it does not exist.         |
   | move      | Moves the target data resource.                       |
   | replace   | Replace the target data resource with the edit value. |
   | remove    | Removes a data resource if it already exists.         |
   | clone     | Clones a data resource and places the copy at the new |
   |           | location.  If the resource does not exist an error is |
   |           | returned.                                             |
   +-----------+-------------------------------------------------------+

                    Table 3: Configure Edit Operations

5.1.1.2.  Edit Operation

   Each Configure includes one or more edits.  These edits include the
   following information:

   Edit-Id:  Uniquely specifies the identifier of the edit within the
       operation.

   Edit-Type:  Specifies the type of operation (see Section 5.1.1.1).

   Command-Set:  The Command-Set is a technology-specific bitset that
       allows for a single entity to be sent in an edit with multiple
       requested, technology specific sub-transactions to be completed.
       It can also provide clarity for a request.  For example, a
       Mobility-Context could have the Home Network Prefix absent but it
       is unclear if the Client would like the address to be assigned by
       the Agent or if this is an error.  Rather than creating a
       specific command for assigning the IP, a bit position in a
       Command-Set can be used to indicate Agent based IP assignment
       requests.



Matsushima, et al.      Expires December 20, 2018              [Page 30]


Internet-Draft              DMM FPC Protocol                   June 2018


   Reference-Scope:  If supported, specifies the Reference Scope (see
       Section 5.1.1.3)

   Target:  Specifies the Target node (Data node path or FPC Identity)
       for the edit operation.  This MAY be a resource, e.g.  Mobility-
       Context, Descriptor-Template, etc., or a data node within a
       resource as specified by its path.

   Point:  The absolute URL path for the data node that is being used as
       the insertion point, clone point or move point for the target of
       this 'edit' entry.

   Where:  Identifies where a data resource will be inserted, cloned to
       or moved.  Only allowed these for lists and lists of data nodes
       that are 'ordered-by user'.  The values are 'before', 'after',
       'first', 'last' (default value).

   Value  The value used for this edit operation.  In this message it
       MUST NOT be a MONITOR entity.

             |
             +-[Configure]
             |         +-[Client-Id:]
             |         +-[(Unsigned 32) Execution-Delay]
             |         +-[Operation-Id:]
             |         +-[Edit:] <List>
             |         |    +-[Edit-Id:] <L-Key>
             |         |    +-[(Enumeration) Edit-Type:]
             |         |    +-[(BitSet) Command-Set]
             |         |    +-[(Enumeration) Reference-Scope]
             |         |    +-[Target:]
             |         |    +-[Point]
             |         |    +-[(Enumeration) Where]
             |         |    +-[Value]

                       Figure 16: Configure Request

   Edits sent to the Agent provided in an operation SHOULD be sent in
   the following order to avoid errors:

   1.  Action Templates

   2.  Descriptor Templates

   3.  Rule Templates

   4.  Policy Templates




Matsushima, et al.      Expires December 20, 2018              [Page 31]


Internet-Draft              DMM FPC Protocol                   June 2018


   5.  DPN Templates

   6.  Mobility Contexts

5.1.1.3.  Reference Scope

   The Reference Scope is an optional feature that provides the scope of
   references used in a configuration command.  These scopes are defined
   as:

   o  none - All edits have no references to other entities or within
      edits.

   o  edit - All references are contained within each edit body (intra-
      edit/intra-operation)

   o  operation - All references exist in the operation (inter-edit/
      intra-operation).

   o  storage - One or more references exist outside of the operation.
      A lookup to cache / storage is required.

   o  unknown - the location of the references are unknown.  This is
      treated as a 'storage' type.

   An Agent that only accepts 'edit' or 'operation' reference scope
   messages is referred to as 'stateless' as it has no direct memory of
   references outside messages themselves.  This permits low memory
   footprint Agents/DPNs.  Even when an Agent supports all message types
   an 'edit' or 'operation' scoped message can be processed quickly by
   the Agent/DPN as it does not require storage access.

   Figure 17 shows an example containment hierarchy provided for all
   caches.

















Matsushima, et al.      Expires December 20, 2018              [Page 32]


Internet-Draft              DMM FPC Protocol                   June 2018


                         +---------------+
                         | Global Cache  |
                         |  (storage)    |
                         +------+--------+
                                |
                                +----------------+
                                |                |
                +------+-----------+      +------+-----------+
                | Operation Cache  |      | Operation Cache  |
                |   (operation)    | .... |   (operation)    |
                +------+-----------+      +--------+---------+
                       |                           |
                   +---+-----------+               |
                   |               |               |
            +------+------+ +------+------+ +------+------+
            | Edit Cache  | | Edit Cache  | | Edit Cache  |
            |   (edit)    | |   (edit)    | |   (edit)    |
            +-------------+ +-------------+ +-------------+

                                (no cache)

                   Figure 17: Example Hierarchical Cache

5.1.1.4.  Operation Response

5.1.1.4.1.  Immediate Response

   The Response MUST include the following:

      Operation Identifier of the corresponding request.

      Global Status for the operation (see Table 1).

      A list of Edit results (described below).

   An edit response, Edit-Status, is comprised of the following:

      Edit-Id: Edit Identifier.

      Edit-Status: OK.

      When the Edit-Status is OK the following values MAY be present

         Notify-Follows - A boolean indicator that the edit has been
         accepted by the Agent but further processing is required.  A
         Configure-Result-Notification will be sent once the processing
         has succeeded or failed.




Matsushima, et al.      Expires December 20, 2018              [Page 33]


Internet-Draft              DMM FPC Protocol                   June 2018


         Subsequent-Edits-List: This is a list of Edits that were
         required to fulfill the request.  It follows the edit request
         semantics (see Section 5.1.1.2).

      Errors-List: When the Edit-Status is ERROR the following values
      are present.  See Table 1 for details.

   The response will minimally contain an Edit-Status implying 'OK' or a
   list of errors.

             |
             +-[Operation-Id:]
             +-[Result-Status:]
             +-[Errors] <List>
             |         +-[(Enumeration) Error-Type:]
             |         +-[(String) Error-Tag:]
             |         +-[(String) Error-App-Tag]
             |         +-[(String) Error-Message]
             |         +-[Error-Info]
             +-[Edit-Status]
             |         +-[Edit-Id:]
             |         +-[Edit-Status: ~ OK]
             |         +-[Notify-Follows]
             |         +-[Subsequent-Edits] <List>
             |         |    +-[Edit-Id:] <L-Key>
             |         |    +-[(Enumeration) Edit-Type:]
             |         |    +-[Target:]
             |         |    +-[Point]
             |         |    +-[(Enumeration) Where]
             |         |    +-[Value]
             |         +-[Errors] <List>
             |         |         +-[(Enumeration) Error-Type:]
             |         |         +-[(String) Error-Tag:]
             |         |         +-[(String) Error-App-Tag]
             |         |         +-[(String) Error-Message]
             |         |         +-[Error-Info]
             |

                  Figure 18: Configure Operation Response

5.1.1.4.2.  Asynchronous Notification

   A Configure-Result-Notification occurs after the Agent has completed
   processing related to a Configure request.  It is an asynchronous
   communication from the Agent to the Client.






Matsushima, et al.      Expires December 20, 2018              [Page 34]


Internet-Draft              DMM FPC Protocol                   June 2018


   It is identical to the immediate response with the exception that the
   Notify-Follows, if present, MUST be false.  As this value is
   unnecessary it SHOULD be omitted.

5.1.1.5.  Reserved Identities

   Several identities are reserved in the Policy Information Model and
   Mobility-Context to facilitate specific uses cases.

   Agents and tenants express their support for descriptors and actions
   using the following Key patterns

      supported-<descriptor template name> indicates a support for the
      descriptor template as defined in its original specification.  For
      example "supported-rfc5777classifier" is a Descriptor Template
      that conforms to the rfc5777-classifier (Figure 31) as defined in
      this document.

      supported-<action template name> indicates a support for the
      action template as defined in its original specification.

      "base-rule" is comprised of all base descriptors using an 'or'
      Descriptor-Match-Type and all Actions in no specific order.

      "base-template" is comprised of the base rule.

   "base-template" can be used to determine supported Action and
   Descriptor Templates.  It can also be used to support an open
   template where any specific Descriptors and Actions can be applied,
   however, depending upon the Order of Actions it is likely to produce
   undesirable results.

   One use case is supported via reservation of specific DPN-Keys:

      Requested policies are those that the Client would like to be
      assigned to a DPN within a Mobility-Context.  The naming
      convention is similar to those used for DPN Assignment via an
      Agent.

         "Requested" is a Key that represents requested policies which
         have not been assigned to a specific DPN.  No Role is assigned
         to the DPN.

         "Requested-<Role>" represents requested policies that have not
         been assigned to a DPN and can only be assigned to DPNs that
         fulfill the specified Role.





Matsushima, et al.      Expires December 20, 2018              [Page 35]


Internet-Draft              DMM FPC Protocol                   June 2018


      It is possible to have policies in the "Requested" DPN that do not
      appear in other entries which reflects the inability to
      successfully assign the policy.

5.1.2.  Monitor Messages

   An Agent may reject a registration if it or the DPN has insufficient
   resources.

   An Agent or DPN MAY temporarily suspend monitoring if insufficient
   resources exist.  In such a case the Agent MUST notify the Client.

   When a monitor has a reporting configuration of SCHEDULED it is
   automatically de-registered after the last Notify occurs.

   If a SCHEDULED or PERIODIC configuration is provided during
   registration with the time related value (time or period
   respectively) of 0 a Notify is sent and the monitor is immediately
   de-registered.  This method should, when a Monitor has not been
   installed, result in an immediate Notify sufficient for the Client's
   needs and lets the Agent realize the Client has no further need for
   the monitor to be registered.

   Probe messages are used by a Client to retrieve information about a
   previously installed monitor.  The Probe message SHOULD identify one
   or more monitors by means of including the associated monitor
   identifier.  An Agent receiving a Probe message sends the requested
   information in a single or multiple Notify messages.

   If the Monitor configuration associated with a Notify can be
   deferred, then the Notify MAY be bundled with other messages back to
   the Agent even if this results in a delay of the Notify.

   The Monitor messages use the following data:

   Monitor-Key:  Monitor Key.

   Monitor:  A Monitor configuration (see Section 4.9.7).

   Send-Data:  An indicator that specifies that the final value MUST be
       sent as a notification from the Agent.










Matsushima, et al.      Expires December 20, 2018              [Page 36]


Internet-Draft              DMM FPC Protocol                   June 2018


             |
             +-[Register-Monitor]
             |         +-[Client-Id:]
             |         +-[(Unsigned 32) Execution-Delay]
             |         +-[Operation-Id:]
             |         +-[Monitor:] <List>
             |         |         +-[Extensible:]
             |         |         +-[Monitor-Key:] <U-Key>
             |         |         +-[Target:]
             |         |         +-[Deferrable]
             |         |         +-[Configuration:]

             |
             +-[Deregister-Monitor]
             |         +-[Client-Id:]
             |         +-[(Unsigned 32) Execution-Delay]
             |         +-[Operation-Id:]
             |         +-[Monitor:] <List>
             |         |         +-[Monitor-Key:] <U-Key>
             |         |         +-[(Boolean) Send-Data ~ False]

             |
             +-[Probe]
             |         +-[Client-Id:]
             |         +-[(Unsigned 32) Execution-Delay]
             |         +-[Operation-Id:]
             |         +-[Monitor-Key:] <List>


                        Figure 19: Monitor Messages

5.1.2.1.  Asynchronous Notification

   A Monitor Report can be sent as part of de-registration, a trigger
   based upon a Monitor Configuration or a Probe.  A Report is comprised
   of the Monitor Key the report applies to, the Trigger for the report,
   a timestamp of when the report's associated event occurs and data,
   Report-Value, that is specific to the monitored value's type.

   Triggers include but are not limited to

   o  Subscribed Event occurred

   o  Low Threshold Crossed

   o  High Threshold Crossed

   o  Periodic Report



Matsushima, et al.      Expires December 20, 2018              [Page 37]


Internet-Draft              DMM FPC Protocol                   June 2018


   o  Scheduled Report

   o  Probe

   o  Deregistration Final Value

   o  Monitoring Suspended

   o  Monitoring Resumed

   o  DPN Available

   o  DPN Unavailable

   Multiple Reports are sent in a Notify message.  Each Notify is
   comprised of unique Notification Identifier from the Agent and
   timestamp indicating when the notification was created.

           |
           +-[ Notify ]
           |         +-[(Unsigned 32) Notification-Identifier:]
           |         +-[Timestamp:]
           |         +-[Report:] <List>
           |         |    +-[Trigger:]
           |         |    +-[Monitor-Key:]
           |         |    +-[Report-Value]

                        Figure 20: Monitor Messages

5.2.  Protocol Operation

   Please note that JSON is used to represent the information in Figures
   in this section but any over the wire representation that accurately
   reflects the information model MAY be used.

5.2.1.  DPN Selection

   In order to assign a DPN to a Mobility Context, the Client or Agent
   requires topology information.  The Service-Group provides
   information, e.g. function, role, protocol, features and
   configuration, to determine suitable DPN interfaces.

   Consider a Client attempting to select DPN interfaces that are served
   by a single Agent.  In this example interfaces are present with
   different protocols, settings and features as shown in the following
   figure.

    "topology-information-model" : {



Matsushima, et al.      Expires December 20, 2018              [Page 38]


Internet-Draft              DMM FPC Protocol                   June 2018


     "dpn" : [ {
      "dpn-key" : "dpn1",
      "interface" : [ {
        "interface-key" : "ifc1",
        "role" : "lma",
        "protocol" : [ "pmip" ],
        "interface-configuration" : [ {
            "index" : 0,
            "setting" : [ "optionA" : "OFF" ]
        } ]
      },{
        "interface-key" : "ifc2",
        "role" : "lma",
        "protocol" : [ "pmip" ],
        "interface-configuration" : [ {
            "index" : 0,
            "setting" : [ "optionC" : "OFF"  ]
         } ]
       },{
        "interface-key" : "ifc2-b",
        "role" : "mag",
        "protocol" : [ "pmip" ]
        } ] },
      {
      "dpn-key" : "dpn2",
      "interface" : [ {
        "interface-key" : "ifc1",
        "role" : "mag",
        "protocol" : [ "pmip" ],
        "interface-configuration" : [ {
          "index" : 0,
          "settings" : [ "optionA" : "OFF", "optionB" : "ON" ]
        } ]
      } ] }
     ],
     ...
     },
     "service-group" : [
     { "service-group-key" : "group1",
       "service-group-name" : "Anchors-OptionA-OFF",
       "role-key" : "lma",
       "protocol" : [ "pmip" ],
       "service-group-configuration" : [ {
            "index" : 0,
            "setting" : [ "optionA" : "OFF" ]
       } ],
       "dpn" : [
       { "dpn-key" : "dpn1",



Matsushima, et al.      Expires December 20, 2018              [Page 39]


Internet-Draft              DMM FPC Protocol                   June 2018


         "referenced-interface" : [ { "interface-key" : "ifc1" } ] }
       ]
     },{ "service-group-key" : "group2",
       "service-group-name" : "Anchors",
       "role-role" : "lma",
       "protocol" : [ "pmip" ],
       "dpn" : [
       { "dpn-key" : "dpn1",
         "referenced-interface" : [ { "interface-key" : "ifc2" } ] }
       ]
      },{ "service-group-key" : "group3",
       "service-group-name" : "MAGs",
       "role-role" : "mag",
       "protocol" : [ "pmip" ],
       "dpn" : [
       { "dpn-key" : "dpn2",
         "referenced-interface" : [ { "interface-key" : "ifc1" } ] },
       { "dpn-key" : "dpn1",
         "referenced-interface" : [ { "interface-key" : "ifc2-b" } ] }
       ]
      }
    ]

   NOTE - A Setting is, in this example, a list of string attributes in
   a Configuration.

                        Figure 21: Monitor Messages

   Two DPNs are present.  The first, dpn1, has 3 interfaces.  Two
   support the LMA role and both have settings.  The third supports the
   MAG function.  The second DPN, dpn2, provides a single interface with
   the MAG function.

   Three ServiceGroups are presented.  The first provides the PMIP
   protocol and LMA role.  It also has a setting, OptionA, that is OFF
   and only contains ifc1 from dpn1.

   The second group is comprised of interfaces that support the PMIP
   protocol and LMA function.  It only contains ifc2 from dpn1.  An
   interface that has setting(s) or feature(s) that must appear in a
   ServiceGroup SHOULD NOT appear in ServiceGroups that do not have
   those setting(s) or feature(s) present.  Thus, ifc1 of dpn1 should
   not be present in this second Service-Group.

   A third group is comprised of interfaces that support the MAG
   function of the LMA protocol.  It contains the MAG interfaces form
   both dpn1 and dpn2.




Matsushima, et al.      Expires December 20, 2018              [Page 40]


Internet-Draft              DMM FPC Protocol                   June 2018


   Given the task to find a LMA that supports the PMIP protocol the
   Client can determine that dpn1 is its only option and, depending on
   its requirement of OptionA, can appropriately determine which
   interface to select.

5.2.2.  Policy Creation and Installation

   A Policy must be installed upon an Agent in order to install policies
   on the selected dpn(s).  This requires construction of the Action(s),
   Descriptor(s) and Rule(s) used by the Policy.

   The CONFIGURE message permits editing all information elements except
   monitors.  The following figure shows use of a CONFIGURE message to
   install policy information on the Agent.

                                                 +-------Router--------+
                            +-----------+        |+-------+ +---------+|
    +------+ +------+     +-----+ FPC   |         | FPC   | |  Anchor |
    |MAG-C1| |MAG-C2|     |LMA-C| Client|         | Agent | |   DPN   |
    +------+ +------+     +-----+-------+         +-------+ +---------+
    |         |            |---(1)--Configure-------->|           |
    |         |          "configure" : {              |           |
    |         |           "client-id" : 0,            |           |
    |         |           "operation-id" : 0,         |           |
    |         |           "edit" : [ {                |           |
    |         |            "edit-id" : 0,             |           |
    |         |            "edit-type" : "create",    |           |
    |         |            "target" : "/policy-information-model/
                              /descriptor-template",              |
    |         |            "value" : {                            |
    |         |              "descriptor-template-key" : "desc1", |
    |         |              "descriptor-type" : "all-traffic" }  |
    |         |             }, {                                  |
    |         |            "edit-id" : 1,             |           |
    |         |            "edit-type" : "create",    |           |
    |         |            "target" : "/policy-information-model/
                              /action-template",                  |
    |         |            "value" : {                            |
    |         |              "action-template-key" : "action1",   |
    |         |              "action-type" : "drop" }             |
    |         |             }, {                                  |
    |         |            "edit-id" : 2,             |           |
    |         |            "edit-type" : "create",    |           |
    |         |            "target" : "/policy-information-model/
                              /rule-template",                    |
    |         |            "value" : {                            |
    |         |              "rule-template-key" : "deny-all",    |
    |         |              "descriptor-match-type" : "and",     |



Matsushima, et al.      Expires December 20, 2018              [Page 41]


Internet-Draft              DMM FPC Protocol                   June 2018


    |         |              "descriptor-configuration" : [{      |
    |         |              "descriptor-template-key" : "all" }],|
    |         |              "action-configuration" : [{          |
    |         |                "action-template-key" : "deny",    |
    |         |                "action-order" : 0 }]              |
    |         |             }, {                                  |
    |         |            "edit-id" : 3,             |           |
    |         |            "edit-type" : "create",    |           |
    |         |            "target" : "/policy-information-model/
                              /policy-template",                  |
    |         |            "value" : {                            |
    |         |              "policy-template-key" : "policy1",   |
    |         |              "entity-state" : "configured",       |
    |         |              "rule-template" : [ {                |
    |         |              "rule-template-key" : "deny-all",    |
    |         |              "precedence" : 0 } ]                 |
    |         |             } } ] }                               |
    |         |            |<---(2)- Response --------|           |
    |         |            | {                        |           |
    |         |            |  "agent-id" : "agent1"," |           |
    |         |            |  "operation-id" : 0,     |           |
    |         |            |  "result-status" : "ok"  |           |
    |         |            | }                        |           |
    |         |            |                          |           |

   Figure 22: Example Policy Installation (focus on FPC reference point)

   In this example a Descriptor "all-traffic" Template and an Action,
   "drop", Template are both empty Templates.  The "deny-all" Rule
   Template is comprised of the action and descriptor.  The Rule is
   included in "policy1".  The policy's status is "Configured" as it is
   a complete policy ready for immediate use.  The policy could be set
   as "Active" if the Client intends to use it upon immediate
   installation in a DPN.

   Installation of the policy on dpn1 is shown in the following Figure.
   The Policy-Status is set to "Active" to make it immediately usable.
   Leaving the status as Configured would permit its installation on the
   DPN without an ability to use it in a Mobility Context.  Such a use
   case is often referred to as policy pre-configuration.











Matsushima, et al.      Expires December 20, 2018              [Page 42]


Internet-Draft              DMM FPC Protocol                   June 2018


                                                 +-------Router--------+
                            +-----------+        |+-------+ +---------+|
    +------+ +------+     +-----+ FPC   |         | FPC   | |  Anchor |
    |MAG-C1| |MAG-C2|     |LMA-C| Client|         | Agent | |   DPN   |
    +------+ +------+     +-----+-------+         +-------+ +---------+
    |         |            |---(1)--Configure-------->|           |
    |         |          "configure" : {              |           |
    |         |           "client-id" : 0,            |           |
    |         |           "operation-id" : 1,         |           |
    |         |           "edit" : [ {                |           |
    |         |            "edit-id" : 0,             |           |
    |         |            "edit-type" : "create",    |           |
    |         |            "target" : "/topology-information-model/
                             /dpn/dpn1/dpn-policy-configuration", |
    |         |            "value" : {                            |
    |         |              "policy-template-key" : "policy1",   |
    |         |              "policy-status" : "active" } } ] }   |
    |         |            |<---(2)- Response --------|-policy--->|
    |         |            | {                        | install   |
    |         |            |  "agent-id" : "agent1"," |           |
    |         |            |  "operation-id" : 1,     |           |
    |         |            |  "result-status" : "ok"  |           |
    |         |            | }                        |           |
    |         |            |                          |           |

   Figure 23: Example Policy Installation (focus on FPC reference point)

   This message uses an edit type of "create" to add the policy template
   directly to the installed DPN policy set.

5.2.3.  Simple RPC Operation

   A Client and Agent MUST identify themselves using the Client
   Identifier and Agent Identifier respectively to ensure that, for all
   transactions, a recipient of a FPC message can unambiguously identify
   the sender of the FPC message.

   A Client MAY direct the Agent to enforce a rule in a particular DPN
   by including a DPN Key value in a Mobility Context.  Otherwise the
   Agent selects a suitable DPN to enforce one or more portions of a
   Mobility Context and notifies the Client about the selected DPN(s)
   using DPN Identifier(s).

   All messages sent from a Client to an Agent MUST be acknowledged by
   the Agent.  The response must include all edit status as well as
   subsequent edits, which indicates the result of processing the
   message, as part of the Configure response.  In case the processing
   of the message results in a failure, the Agent sets the global



Matsushima, et al.      Expires December 20, 2018              [Page 43]


Internet-Draft              DMM FPC Protocol                   June 2018


   status, Error-Type and Error-Tag accordingly and MAY clear the
   entity, e.g.  Mobility-Context, which caused the failure, in the
   response.

   If based upon Agent configuration or the processing of the request
   possibly taking a significant amount of time the Agent MAY respond
   with a Notify-Follows indication with optional Subsequent-Edit(s)
   containing the partially completed entity modifications.  When a
   Notify-Follows indication is sent in a response, the Agent will, upon
   completion or failure of the operation, respond with an asynchronous
   Configuration-Result-Notification to the Client.

   A Client MAY add a property to a Mobility-Context without providing
   all required details of the attribute's value.  In such case the
   Agent SHOULD determine the missing details and provide the completed
   property description, via Subsequent-Edit(s), back to the Client.  If
   the processing will take too long or based upon Agent configuration,
   the Agent MAY respond with an OK for the Edit that indicates a
   Notify-Follows and also includes Subsequent-Edit(s) containing the
   partially completed entity edits.

   In case the Agent cannot determine the missing value of an
   attribute's value per the Client's request, it leaves the attribute's
   value cleared, sets the Edit Result to Error and provides an Error-
   Type and Error-Tag. As example, the Control-Plane needs to setup a
   tunnel configuration in the Data-Plane but has to rely on the Agent
   to determine the tunnel endpoint which is associated with the DPN
   that supports the Mobility-Context.  The Client adds the tunnel
   property attribute to the FPC message and clears the value of the
   attribute (e.g.  IP address of the local tunnel endpoint).  The Agent
   determines the tunnel endpoint and includes the completed tunnel
   property in its response to the Client in a Subsequent-Edit entry.

   Figure 24 illustrates an exemplary session life-cycle based on Proxy
   Mobile IPv6 registration via MAG Control-Plane function 1 (MAG-C1)
   and handover to MAG Control-Plane function 2 (MAG-C2).  Edge DPN1
   represents the Proxy CoA after attachment, whereas Edge DPN2 serves
   as Proxy CoA after handover.  As exemplary architecture, the FPC
   Agent and the network control function are assumed to be co-located
   with the Anchor-DPN, e.g. a Router.

   The Target of the second request uses the Mobility-Context by name.
   Alternatively, the Target could have included the DPN-Key and Policy-
   Key to further reduce the amount of information exchanged.  Setting
   the Target's value to the most specific node SHOULD be followed
   whenever practical.

                                                +-------Router--------+



Matsushima, et al.      Expires December 20, 2018              [Page 44]


Internet-Draft              DMM FPC Protocol                   June 2018


                           +-----------+        |+-------+ +---------+|
   +------+ +------+     +-----+ FPC   |         | FPC   | |  Anchor |
   |MAG-C1| |MAG-C2|     |LMA-C| Client|         | Agent | |   DPN1  |
   +------+ +------+     +-----+-------+         +-------+ +---------+
   [MN attach]  |            |                          |           |
      |-------------PBU----->|                          |           |
      |         |            |---(1)--Configure-------->|           |
      |         |  "configure" : {                      |           |
      |         |    "client-id" : 0,                   |           |
      |         |    "operation-id" : 3,                |           |
      |         |    "edit" : [                         |           |
      |         |      "edit-id" : 0,                   |           |
      |         |      "edit-type" : "create",          |           |
      |         |      "target" : "/mobility-context",              |
      |         |      "value" : {                                  |
      |         |        "mobility-context-key" : "ctxt1",          |
      |         |        "delegating-ip-prefix" : [ <HNP> ],        |
      |         |        "dpn" : [ {                                |
      |         |          "dpn-key" : "DPN1",                      |
      |         |          "role" : "lma",                          |
      |         |          "service-data-flow" : [ {
      |         |            "identifier" : 0,
      |         |            "interface" : [ "interface-key" : "ifc1" ],
      |         |            "service-data-flow-policy-configuration" :[
      |         |              {"policy-template-key" :
                                   "dl-tunnel-with-qos",
      |         |                "policy-status" : "active",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 0,
      |         |                   "qos-template" : <QOS Settings...>},
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <DL tunnel info...>},
      |         |               {"policy-template-key" : "ul-tunnel",
      |         |                   "policy-status" : "active",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <UL tunnel info...>}] }]
      |         |           } ] } ] } ] } ] }           |           |
      |         |            |                          |--tun1 up->|
      |         |            |                          |           |
      |         |            |                          |--tc qos-->|
      |         |            |                          |           |
      |         |            |<---(2)- Response --------|-route add>|
      |         |            | {                        |           |
      |         |            |  "agent-id" : "agent1"," |           |
      |         |            |  "operation-id" : 3,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            |  }                       |           |



Matsushima, et al.      Expires December 20, 2018              [Page 45]


Internet-Draft              DMM FPC Protocol                   June 2018


      |         |            |                          |           |
      |<------------PBA------|                          |           |
      |         |            |                          |           |
      | +----+  |            |                          |           |
      | |Edge|  |            |                          |           |
      | |DPN1|  |            |                          |           |
      | +----+  |            |                          |           |
      |   |                                                         |
      |   |-=======================================================-|
      |                      |                          |           |
      |   [MN handover]      |                          |           |
      |         |---PBU ---->|                          |           |
      |         |            |--(3)- CONFIG(MODIFY)---->|           |
      |         |  "configure" : {                      |-tun1 mod->|
      |         |    "client-id" : 0,                   |           |
      |         |    "operation-id" : 4,                |           |
      |         |    "edit" : [                         |           |
      |         |      "edit-id" : 0,                   |           |
      |         |      "edit-type" : "merge",           |           |
      |         |      "target" : "/mobility-context/ctxt1",        |
      |         |      "value" : {                                  |
      |         |        "mobility-context-key" : "ctxt1",          |
      |         |        "dpn" : "[ {                               |
      |         |          "dpn-key" : "DPN1",                      |
      |         |          "service-data-flow" : [ {
      |         |            "identifier" : 0,
      |         |            "service-data-flow-policy-configuration":[
      |         |                {"policy-template-key" :
                                        "dl-tunnel-with-qos",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <NEW tunnel info...>}]}]
      |         |           } ] } ] } ] }               |           |
      |         |<--PBA------|                          |           |
      |         |            |                          |-tun1 mod->|
      |         |            |<---(4)- OK --------------|           |
      |         |            | {                        |           |
      |         |            |  "agent-id" : "agent1"," |           |
      |         |            |  "operation-id" : 4,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            |  }                       |           |
      |         |  +----+    |                          |           |
      |         |  |Edge|    |                          |           |
      |         |  |DPN2|    |                          |           |
      |         |  +----+    |                          |           |
      |         |    |       |                          |           |
      |         |    |-============================================-|
      |         |            |                          |           |



Matsushima, et al.      Expires December 20, 2018              [Page 46]


Internet-Draft              DMM FPC Protocol                   June 2018


   Figure 24: Single Agent with Handover (focus on FPC reference point)

   After reception of the Proxy Binding Update (PBU) at the LMA Control-
   Plane function (LMA-C), the LMA-C selects a suitable DPN, which
   serves as Data-Plane anchor to the mobile node's (MN) traffic.  The
   LMA-C adds a new logical Mobility-Context to the DPN to treat the
   MN's traffic (1) and includes a Mobility-Context-Key (ctxt1) in the
   Configure command.  The LMA-C identifies the selected Anchor DPN by
   including the associated DPN identifier.

   The LMA-C adds policy template properties during the creation of the
   new Mobility-Context.  One policy, "dl-tunnel-with-qos", is an
   example template that permits tunnel forwarding of traffic destined
   to the MN's HNP, i.e. downlink traffic, with optional QoS parameters.
   Another policy, "ul-tunnel", provides a simple uplink anchor
   termination template where uplink tunnel information is provided.

   The downlink tunnel information specifies the destination endpoint
   (Edge DPN1).

   Upon reception of the Mobility-Context, the FPC Agent utilizes local
   configuration commands to create the tunnel (tun1) as well as the
   traffic control (tc) to enable QoS differentiation.  After
   configuration has been completed, the Agent applies a new route to
   forward all traffic destined to the MN's HNP specified as a property
   in the Mobility-Context and applied the configured tunnel interface
   (tun1).

   During handover, the LMA-C receives an updating PBU from the handover
   target MAG-C2.  The PBU refers to a new Data-Plane node (Edge DPN2)
   to represent the new tunnel endpoint in the downlink as required.
   The LMA-C sends a Configure message (3) to the Agent to modify the
   existing tunnel property of the existing Mobility-Context and to
   update the downlink tunnel endpoint from Edge DPN1 to Edge DPN2.
   Upon reception of the Configure message, the Agent applies updated
   tunnel property to the local configuration and responds to the Client
   (4).

                                                 +-------Router--------+
                           +-----------+         |+-------+ +---------+|
   +------+ +------+     +-----+ FPC   |          | FPC   | |  Anchor |
   |MAG-C1| |MAG-C2|     |LMA-C| Client|          | Agent | |   DPN   |
   +------+ +------+     +-----+-------+          +-------+ +---------+
   [MN detach]  |            |                          |           |
      |-------------PBU----->|                          |           |
      |         |            |---(1)--Configure-------->|           |
      |         |          "configure" : {              |           |
      |         |           "client-identifier" : 0,    |           |



Matsushima, et al.      Expires December 20, 2018              [Page 47]


Internet-Draft              DMM FPC Protocol                   June 2018


      |         |           "operation-id" : 5,         |           |
      |         |           "edits" : [                 |           |
      |         |            "edit-id" : 0,             |           |
      |         |            "edit-type" : "merge",     |           |
      |         |            "target" : "/mobility-context/ctxt1    |
      |         |                /dpn/DPN1/service-data-flow/0      |
      |         |                /service-data-flow-policy-
                                  configuration/dl-tunnel-with-qos/1"
      |         |            "value" : {                |           |
      |         |                  "tunnel" : null      |           |
      |         |             } ] }                     |           |
      |<------------PBA------|                          |--tun1   ->|
      |         |            |                          |    down   |
      |         |            |                          |           |
      |         |            |<---(2)- Response --------|           |
      |         |            | {                        |           |
      |         |            |  "agent-id" : "agent1"," |           |
      |         |            |  "operation-id" : 5,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            | }                        |           |
      |         |            |                          |           |
      |         |  [ MinDelayBeforeBCEDelete expires ]  |           |
      |         |            |                          |           |
      |         |            |---(3)--Configure-------->|-- tun1 -->|
      |         |          "configure" : {              |  delete   |
      |         |           "client-identifier" : 0,    |           |
      |         |           "operation-id" : 6,         |           |
      |         |           "edits" : [                 |           |
      |         |            "edit-id" : 0,             |           |
      |         |            "edit-type" : "delete",    |           |
      |         |            "target" : "/mobility-context/ctxt1"   |
      |         |            ] }                        |           |
      |         |            |                          |           |
      |         |            |<---(4)- Response --------|           |
      |         |            | {                        |           |
      |         |            |  "agent-id" : "agent1"," |           |
      |         |            |  "operation-id" : 6,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            | }                        |           |
      |         |            |                          |-- route ->|
      |         |            |                          |   remove  |
      |         |            |                          |           |

   Figure 25: Single Agent with Deletion (focus on FPC reference point)

   When a teardown of the session occurs, MAG-C1 will send a PBU with a
   lifetime value of zero.  The LMA-C sends a Configure message (1) to
   the Agent to modify the existing tunnel property of the existing



Matsushima, et al.      Expires December 20, 2018              [Page 48]


Internet-Draft              DMM FPC Protocol                   June 2018


   Mobility-Context to delete the tunnel information.  Upon reception of
   the Configure message, the Agent removes the tunnel configuration and
   responds to the Client (2).  Per [RFC5213], the PBA is sent back
   immediately after the PBA is received.

   If no valid PBA is received after the expiration of the
   MinDelayBeforeBCEDelete timer (see [RFC5213]), the LMA-C will send a
   Configure (3) message with a deletion request for the Context.  Upon
   reception of the message, the Agent deletes the tunnel and route on
   the DPN and responds to the Client (4).

   When a multi-DPN Agent is used the DPN list permits several DPNs to
   be provisioned in a single message for the single Mobility-Context.

                           +-----------+           +-------+ +---------+
   +------+ +------+     +-----+ FPC   |           | FPC   | |  Anchor |
   |MAG-C1| |MAG-C2|     |LMA-C| Client|           | Agent | |   DPN1  |
   +------+ +------+     +-----+-------+           +-------+ +---------+
   [MN attach]  |            |                          |           |
      |-------------PBU----->|                          |           |
      |         |            |---(1)--Configure-------->|           |
      |         |  "configure" : {                      |--tun1 up->|
      |         |    "client-id" : 0,                   |           |
      |         |    "operation-id" : 0,                |           |
      |         |    "edit" : [                         |--tc qos-->|
      |         |      "edit-id" : 0,                   |           |
      |         |      "edit-type" : "create",          |           |
      |         |      "target" : "/mobility-context",              |
      |         |      "value" : {                                  |
      |         |        "mobility-context-key" : "ctxt1",          |
      |         |        "delegating-ip-prefix" : [ <HNP> ],        |
      |         |        "dpn" : [ {                                |
      |         |          "role" : "lma",                          |
      |         |          "dpn-key" : "DPN1",                      |
      |         |          "service-data-flow" : [ {
      |         |            "identifier" : 0,
      |         |            "interface" : [ "interface-key" : "ifc1" ],
      |         |            "service-data-flow-policy-configuration" :[
      |         |              {"policy-template-key" :
                                        "dl-tunnel-with-qos",
      |         |                "policy-status" : "active",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 0,
      |         |                   "qos-template" : <QOS Settings...>},
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <DL tunnel info...>},
      |         |               {"policy-template-key" : "ul-tunnel",
      |         |                   "policy-status" : "active",



Matsushima, et al.      Expires December 20, 2018              [Page 49]


Internet-Draft              DMM FPC Protocol                   June 2018


      |         |                "policy-configuration" : [
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <UL tunnel info...>}] }]
      |         |              } ] } ] }, {
      |         |          "dpn-key" : "DPN2",                         |
      |         |          "role" : "mag",                             |
      |         |          "service-data-flow" : [ {
      |         |            "identifier" : 0,
      |         |            "interface" : [ "interface-key" : "ifc2" ],
      |         |            "service-data-flow-policy-configuration" :[
      |         |              {"policy-template-key" :
      "dl-tunnel-with-qos",
      |         |                "policy-status" : "active",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 0,
      |         |                   "qos-template" : <QOS Settings...>},
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <DL tunnel info...>},
      |         |               {"policy-template-key" : "ul-tunnel",
      |         |                   "policy-status" : "active",
      |         |                "policy-configuration" : [
      |         |                  {"index" : 1,
      |         |                   "tunnel" : <UL tunnel info...>}] }]
      |         |              } ] } ] }                |           |
      |         |              ] } ] }                  |           |
      |         |            |                          |           |
      |         |            |<---(2)- Response --------|           |
      |         |            | {                        |-route add>|
      |         |            |  "agent-id" : "agent1"," |           |
      |         |            |  "operation-id" : 0,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            |  "notify-follows" : "true",          |
      |         |            | }                        |           |
      |         |            |                          |           |
      |<------------PBA------|                          |           |
      |         |            |                          |           |
      | +----+               |                          |           |
      | |Edge|               |                          |           |
      | |DPN2|               |                          |           |
      | +----+               |                          |           |
      |   |<---------------------- tun1 up -------------|           |
      |   |<---------------------- tc qos --------------|           |
      |   |<---------------------- route add -----------|           |
      |   |                  |                          |           |
      |         |            |<(3) Configure-Result-    |           |
      |         |            |       Notification       |           |
      |         |            | {                        |-route add>|
      |         |            |  "agent-id" : "agent1"," |           |



Matsushima, et al.      Expires December 20, 2018              [Page 50]


Internet-Draft              DMM FPC Protocol                   June 2018


      |         |            |  "operation-id" : 3,     |           |
      |         |            |  "result-status" : "ok", |           |
      |         |            |  "notify-follows" : "true",          |
      |         |            |  "edit-status" : [       |           |
      |         |            |    "edit-id" : 0,        |           |
      |         |            |    "edit-status" : "ok"  |           |
      |         |            | ] }                      |           |
      |         |            |                          |           |
      |   |                  |                          |           |

         Figure 26: Exemplary Message Sequence for Multi-DPN Agent

   Figure 26 shows how the first 2 messages in Figure 24 are supported
   when a multi-DPN Agent communicates with both Anchor DPN1 and Edge
   DPN2.  In such a case, the FPC Client sends the downlink and uplink
   for both DPNs in the DPN Reference List of the same Mobility-Context.
   Message 1 shows the DPN Set with all entries.  Each entry identifies
   the DPN.

   The Agent responds with an OK and Notify-Follows indication while it
   simultaneously provisions both DPNs.  Upon successful completion, the
   Agent responds to the Client with a Configuration-Result-Notification
   indicating the operation status.

5.2.4.  Policy and Mobility on the Agent

   A Client may build Policy and Topology using Configure messages.

   The Client may add, modify or delete many DPN Policies as DPN Policy
   Configurations and Mobility-Contexts in a single FPC message.  This
   includes linking Mobility-Contexts to DPN Policies as well as
   creating the Policy, Rules Actions and Descriptors.  As example, a
   Rule which performs re-writing of an arriving packet's destination IP
   address from IP_A to IP_B matching an associated Descriptor, can be
   enforced in the Data-Plane via an Agent to implicitly consider
   matching arriving packet's source IP address against IP_B and re-
   write the source IP address to IP_A.

   Figure 27 illustrates the generic policy configuration model as used
   between a FPC Client and a FPC Agent.











Matsushima, et al.      Expires December 20, 2018              [Page 51]


Internet-Draft              DMM FPC Protocol                   June 2018


      Descriptor_1 -+          +- Action_1
                    |          |
      Descriptor_2 -+--<Rule>--+- Action_2
                      +-----------+
                      /Precendent#/--------+
                      +----------+         |
                                           |
      Descriptor_3 -+          +- Action_3 +-<Policy>
                    |          |           |  ^
      Descriptor_4 -+--<Rule>--+- Action_4 |  |
                      +-----------+        |  |
                      /Precendent#/--------+  |
                      +----------+            |
                                             <DPN-Policy-Configuration>

      +---------------------+     +----------------------+
      | Bind 1..M traffic   |     |  Bind 1..N traffic   |
      |  Descriptors to     | --> |  treatment actions   |
      |  to a Policy        |     |   to a Policy        |
      +---------------------+     +----------------------+

     |                                                 |
     +-------------- Data-Plane Rule ------------------+

               Figure 27: Structure of Configurable Policies

   As depicted in Figure 27, the DPN Settings represents the anchor of
   Rules through the Policy / Rule hierarchy.  A Client and Agent use
   the identifier of the associated Policy to directly access the Rule
   and perform modifications of traffic Descriptors or Action
   references.  Arriving packets are matched against traffic according
   to Rule precedence and Descriptors.  If a Rule is applicable the
   packet is treated according to the ordered Action values.

   A Client associates a Precedence value for the Rule's Descriptors, to
   allow unambiguous traffic matching on the Data-Plane.

   Figure 28 illustrates the generic context configuration model as used
   between a Client and an Agent.












Matsushima, et al.      Expires December 20, 2018              [Page 52]


Internet-Draft              DMM FPC Protocol                   June 2018


             <Policy 1>
                   ^
                   |
             <Service-Data-Flow 0> <--- <Mobility-Context-ID2>
                                                  ^
                                                  |
             <Policy 1>                           |
             ^                                    |
             |                                    |
             <Service-Data-Flow 0> <--- <Mobility-Context-ID1>

             +-------------------+     +---------------------+
             | Bind 1..M traffic |     |  Bind 1..N traffic  |
             |    selectors to   | --> |  treatment / qos    |
             |     a Context     |     |  actions to a       |
             |                   |     |       Context       |
             +-------------------+     +---------------------+

            |                                                 |
            +-------------- Data-Plane Rule ------------------+

                   Figure 28: Mobility Context Hierarchy

   Figure 28 represents a mobility session hierarchy.  A Client and
   Agent directly assigns values such as downlink traffic descriptors,
   QoS information, etc.  A Client and Agent use the context identifiers
   to access the descriptors, qos information, etc. to perform
   modifications.  From the viewpoint of packet processing, arriving
   packets are matched against traffic Descriptors and processed
   according to the qos or other mobility profile related Actions
   specified in the Mobility-Context's and Service-Data-Flow's'
   properties.  If present, a Policy could contain tunnel information to
   encapsulate and forward the packet.

   A second Mobility-Context also references Mobility-Context-ID1 in the
   figure.  Based upon the technology a property in a parent context
   (parent mobility-context-id reference) MAY be inherited by its
   descendants.  This permits concise over the wire representation.
   When a Client deletes a parent Context all children are also deleted.

5.2.5.  Monitor Example

   The following example shows the installation of a DPN level monitor
   (1) to observe ifc1 status, a property that is either "up" or "down",
   and another monitor to watch for interface events.  The interface
   experiences an outage which is reported to the Client via a Notify
   (3) message.  At a later time a Probe (4) and corresponding Notify
   (5) is sent.  Finally, the monitors are de-registered (6).



Matsushima, et al.      Expires December 20, 2018              [Page 53]


Internet-Draft              DMM FPC Protocol                   June 2018


   Note, specific event identifiers and types are out of scope.

                                                 +-------Router--------+
                            +-----------+        |+-------+ +---------+|
    +------+ +------+     +-----+ FPC   |         | FPC   | |  Anchor |
    |MAG-C1| |MAG-C2|     |LMA-C| Client|         | Agent | |   DPN   |
    +------+ +------+     +-----+-------+         +-------+ +---------+
    |         |            |---(1)--Configure-------->|           |
    |         |          "register-monitor" : {       |           |
    |         |           "client-id" : 0,            |           |
    |         |           "operation-id" : 0,         |           |
    |         |           "monitor" : [ {             |           |
    |         |            "monitor-key" : "ifc1-status",         |
    |         |            "target" : "/dpn/dpn1/interface/ifc1/status"
    |         |            "deferrable" : false                   |
    |         |            }, {                                   |
    |         |            "monitor-key" : "ifc1-events",         |
    |         |            "target" : "/dpn/dpn1/interface/ifc1"  |
    |         |            "deferrable" : false,                  |
    |         |            "configuration" : {                    |
    |         |                "target-event-configuration" : [ 0,
    |         |                  1, 3, .. ] } } ] }               |
    |         |            |<---(2)- Response --------|           |
    |         |            | {                        |           |
    |         |            |  "agent-id" : "agent1"," |           |
    |         |            |  "operation-id" : 0,     |           |
    |         |            |  "result-status" : "ok", |           |
    |         |            | }                        |           |
    |         |            |                          |           |
             [ ifc1 goes down which is reported as event type 3 ]
    |         |            |<---(3)-- NOTIFY ---------|           |
    |         |          "notify" : {                 |           |
    |         |           "notification-id" : 0,      |           |
    |         |           "timestamp" : ...,          |           |
    |         |           "report" : [ {              |           |
    |         |            "monitor-key" : "ifc1-events",         |
    |         |            "trigger" : "subscribed-event-occurred",
    |         |            "report-value" : { 3 } } ] }           |
    |         |            |                          |           |
    |         |            |---(4)--  Probe  -------->|           |
    |         |          "probe" : {      |           |
    |         |           "client-id" : 0,            |           |
    |         |           "operation-id" : 1,         |           |
    |         |           "monitor" : [               |           |
    |         |            "monitor-key" : "ifc1-status" ] }      |
    |         |            |<---(5)- Response --------|           |
    |         |            | {                        |           |
    |         |            |  "agent-id" : "agent1"," |           |



Matsushima, et al.      Expires December 20, 2018              [Page 54]


Internet-Draft              DMM FPC Protocol                   June 2018


    |         |            |  "operation-id" : 1,     |           |
    |         |            |  "result-status" : "ok", |           |
    |         |            | }                        |           |
    |         |            |                          |           |
    |         |            |<---(6)-- NOTIFY ---------|           |
    |         |          "notify" : {                 |           |
    |         |           "notification-id" : 1,      |           |
    |         |           "timestamp" : ...,          |           |
    |         |           "report" : [ {              |           |
    |         |            "monitor-key" : "ifc1-status",         |
    |         |            "trigger" : "probe",
    |         |            "report-valuerporte" : { "up" } } ] }  |
    |         |            |                          |           |
    |         |            |---(7)- Deregister ------>|           |
    |         |          "deregister-monitor" : {     |           |
    |         |           "client-id" : 0,            |           |
    |         |           "operation-id" : 2,         |           |
    |         |           "monitor" : [               |           |
    |         |            { "monitor-key" : "ifc1-events" },     |
    |         |            { "monitor-key" : "ifc1-status",       |
    |         |              "send-data" : true } ] }             |
    |         |            |<---(8)- Response --------|           |
    |         |            | {                        |           |
    |         |            |  "agent-id" : "agent1"," |           |
    |         |            |  "operation-id" : 2,     |           |
    |         |            |  "result-status" : "ok", |           |
    |         |            | }                        |           |
    |         |            |                          |           |
    |         |            |<---(9)-- NOTIFY ---------|           |
    |         |          "notify" : {                 |           |
    |         |           "notification-id" : 2,      |           |
    |         |           "timestamp" : ...,          |           |
    |         |           "report" : [ {              |           |
    |         |            "monitor-key" : "ifc1-status",         |
    |         |            "trigger" : "deregistration-final-value",
    |         |            "report-value" : { "up" } } ] }        |

         Figure 29: Monitor Example (focus on FPC reference point)

6.  Templates and Command Sets

   Configuration templates are shown below.

6.1.  Monitor Configuration Templates

   A periodic configuration specifies a time interval (ms) for
   reporting.




Matsushima, et al.      Expires December 20, 2018              [Page 55]


Internet-Draft              DMM FPC Protocol                   June 2018


   A scheduled configuration specifies a time for reporting.

   A threshold configuration MUST have at least one hi or low threshold
   and MAY have both.

   A Target-Events-Configuration is a list of Events that, when
   generated by the Target, results in a Monitor notification.

        |
        +-[Monitor] <List>
        ...
        |         +-[Configuration]
        |         |     +-[Periodic-Configuration]
        |         |     |       +-[(Unsigned32) Period:]
        ...
        |         +-[Configuration]
        |         |     +-[Schedule-Configuration]
        |         |     |       +-[(Unsigned32) Schedule:]
        ...
        |         +-[Configuration]
        |         |     +-[Threshold-Configuration]
        |         |     |       +-[(Unsigned32) Low]
        |         |     |       +-[(Unsigned32) Hi]
        ...
        |         +-[Configuration]
        |         |     +-[Target-Events-Configuration]
        |         |     |       +-[(Unsigned32) Event-Key:] <List>

                Figure 30: Monitor Configuration Templates

6.2.  Descriptor Templates

   A IP-Prefix-Template MUST have at least the To or From IP Prefix /
   Length populated.  The IP Prefix specifies and Address and Length.

   The PMIP Traffic Selector template is mapped according to [RFC6088]

   The RFC 5777 Classifier is a structured version of common filter
   rules and follows the format specified in [RFC5777].  The Flow-Label,
   Flow-Label range and ECN-IP-Codepoint specified in [RFC7660] are
   added to the Descriptor as well.

     |
     +-[ip-prefix-template]
     |       +-[(IP Prefix / Length) To-IP-Prefix]
     |       +-[(IP Prefix / Length) From-IP-Prefix]
     ...
     +-[pmip-traffic-selector]



Matsushima, et al.      Expires December 20, 2018              [Page 56]


Internet-Draft              DMM FPC Protocol                   June 2018


     |       +-[(Enumerated - IPv4 or IPv6) ts-format]
     |       +-[ipsec-spi-range]
     |       |   +-[ (ipsec-spi) start-spi: ]
     |       |   +-[ (ipsec-spi) end-spi ]
     |       +-[source-port-range]
     |       |   +-[ (port-number) start-port: ]
     |       |   +-[ (port-number) end-port ]
     |       +-[destination-port-range]
     |       |   +-[ (port-number) start-port: ]
     |       |   +-[ (port-number) end-port ]
     |       +-[source-address-range-v4]
     |       |   +-[ (ipv4-address) start-address: ]
     |       |   +-[ (ipv4-address) end-address ]
     |       +-[destination-address-range-v4]
     |       |   +-[ (ipv4-address) start-address: ]
     |       |   +-[ (ipv4-address) end-address ]
     |       +-[ds-range]
     |       |   +-[ (dscp) start-ds: ]
     |       |   +-[ (dscp) end-ds ]
     |       +-[protocol-range]
     |       |   +-[ (uint8) start-protocol: ]
     |       |   +-[ (uint8) end-protocol ]
     |       +-[source-address-range-v6]
     |       |   +-[(ipv6-address) start-address: ]
     |       |   +-[(ipv6-address) end-address ]
     |       +-[destination-address-range-v6]
     |       |   +-[(ipv6-address) start-address: ]
     |       |   +-[(ipv6-address) end-address ]
     |       +-[flow-label-range]
     |       |   +-[(ipv6-flow-label) start-flow-label ]
     |       |   +-[(ipv6-flow-label) end-flow-label ]
     |       +-[traffic-class-range]
     |       |   +-[ (dscp) start-traffic-class ]
     |       |   +-[ (dscp) end-traffic-class ]
     |       +-[next-header-range]
     |       |   +-[ (uint8) start-next-header ]
     |       |   +-[ (uint8) end-next-header ]
     ...
     +-[rfc5777-classifier]
     |       +-[Extensible: True]
     |       +-[(uint8) protocol]
     |       +-[(Enumerated - In/Out/Both) Direction]
     |       +-[From-Spec] <List>
     |       |    +-[(ip-address) IP-Address] <List>
     |       |    +-[IP-Address-Range] <List>
     |       |    |    +-[(ip-address) IP-Address-Start]
     |       |    |    +-[(ip-address) IP-Address-End]
     |       |    +-[IP-Address-Mask] <List>



Matsushima, et al.      Expires December 20, 2018              [Page 57]


Internet-Draft              DMM FPC Protocol                   June 2018


     |       |    |    +-[(ip-address) IP-Address:]
     |       |    |    +-[(Unsigned 32) IP-Bit-Mask-Width:]
     |       |    +-[(mac-address) MAC-Address] <List>
     |       |    +-[MAC-Address-Mask] <List>
     |       |    |    +-[(mac-address) MAC-Address:]
     |       |    |    +-[(mac-address) MAC-Address-Mask-Pattern:]
     |       |    +-[(eui64-address) EUI64-Address] <List>
     |       |    +-[EUI64-Address-Mask] <List>
     |       |    |    +-[(eui64-address) EUI64-Address:]
     |       |    |    +-[(eui64-address) EUI64-Address-Mask-Pattern:]
     |       |    +-[(Integer 32) Port] <List>
     |       |    +-[Port-Range] <List>
     |       |    |    +-[(Integer 32) Port-Start]
     |       |    |    +-[(Integer 32) Port-End]
     |       |    +-[(Boolean) Negated]
     |       |    +-[(Boolean) Use-Assigned-Address]
     |       +-[To-Spec] <List> (O)
     |       |    +-[(ip-address) IP-Address] <List>
     |       |    +-[IP-Address-Range] <List>
     |       |    |    +-[(ip-address) IP-Address-Start]
     |       |    |    +-[(ip-address) IP-Address-End]
     |       |    +-[IP-Address-Mask] <List>
     |       |    |    +-[(ip-address) IP-Address:]
     |       |    |    +-[(Unsigned 32) IP-Bit-Mask-Width:]
     |       |    +-[(mac-address) MAC-Address] <List>
     |       |    +-[MAC-Address-Mask] <List>
     |       |    |    +-[(mac-address) MAC-Address:]
     |       |    |    +-[(mac-address) MAC-Address-Mask-Pattern:]
     |       |    +-[(eui64-address) EUI64-Address] <List>
     |       |    +-[EUI64-Address-Mask] <List>
     |       |    |    +-[(eui64-address) EUI64-Address:]
     |       |    |    +-[(eui64-address) EUI64-Address-Mask-Pattern:]
     |       |    +-[(Integer 32) Port] <List>
     |       |    +-[Port-Range] <List>
     |       |    |    +-[(Integer 32) Port-Start]
     |       |    |    +-[(Integer 32) Port-End]
     |       |    +-[(Boolean) Negated]
     |       |    +-[(Boolean) Use-Assigned-Address]
     |       +-[(dscp) Diffserv-Code-Point] <List>
     |       +-[(Boolean) Fragmentation-Flag ~ False]
     |       +-[IP-Option] <List>
     |       +-[TCP-Option] <List>
     |       +-[TCP-Flags]
     |       +-[ICMP-Type] <List>
     |       +-[ETH-Option] <List>
     |       +-[ecn-ip-codepoint] <List>
     |       +-[(flowlabel) flow-label] <List>
     |       +-[flow-label-range] <List>



Matsushima, et al.      Expires December 20, 2018              [Page 58]


Internet-Draft              DMM FPC Protocol                   June 2018


     |       |    +-[(flowlabel) flow-label-start]
     |       |    +-[(flowlabel) flow-label-end]

                      Figure 31: Descriptor Templates

6.3.  Tunnel Templates

   The Network Service Header is specified in [RFC8300].

   The MPLS SR Stack is specified in
   [I-D.ietf-spring-segment-routing-mpls].

   The IPv6 SR Stack is specified in
   [I-D.ietf-6man-segment-routing-header].

   A tunnel MUST have the local-address or remote-address (or both)
   populated.

   For GRE, the gre-key MUST be present.

   For GTP (GPRS Tunneling Protocol), the following attributes MAY be
   present

      local tunnel endpoint identifier (teid) - MUST be present if
      local-address is nonempty

      remote tunnel endpoint identifier (teid) - MUST be present if
      remote-address is nonempty

      sequence-numbers-on - Indicates that sequence numbers will be used

   Tunnels can be used as Next Hop and Descriptor values.



















Matsushima, et al.      Expires December 20, 2018              [Page 59]


Internet-Draft              DMM FPC Protocol                   June 2018


     |
     +-[next-hop-template]
     |     +-[Extensible: True]
     |     +-[(ip-address) address]
     |     +-[(mac-address) mac-address]
     |     +-[(service-path-id) service-path]
     |     +-[(mpls-label) mpls-path]
     |     +-[(network service header) nsh]
     |     +-[(Unsigned Integer) interface]
     |     +-[(Unsigned 128) segment-identifier]
     |     +-[(MPLS Stack) mpls-label-stack]
     |     +-[(MPLS SR Stack) mpls-sr-stack]
     |     +-[(IPv6 SR Stack) srv6-stack]
     |     +-[tunnel-template]
     ...
     |
     +-[tunnel-template]
     |     +-[Extensible: True]
     |     +-[(address) local-address]
     |     +-[(address) remote-address]
     |     +-[mtu]
     |     +-[(Enumeration - ipv4(0), ipv6(1), dual(2) payload_type:]
     |     +-[(Enumeration - ip-in-ip(0),
                   udp(1), gre(2), gtpv1(3), gtpv2(4)) type:]
     |     +-[interface]
     |     +-[next-hop]
     |     +-[gre-key:] (type == gre)
     |     +-[gtp-info] (type == gtpv1 or type == gtpv2 )
     |     |    +-[(Unsigned 32) local-teid]
     |     |    +-[(Unsigned 32) remote-teid]
     |     |    +-[(Boolean) sequence-numbers-on] (type == gtpv1)

                        Figure 32: Tunnel Templates

6.4.  Action Templates

   The following figure shows common next-hop (set next-hop) and tunnel
   templates for Actions.

   Drop action has no values.

   Rewrite uses a Descriptor to set the values of the packet.  Exactly
   one Descriptor MUST be present.  Only the Destination and Source port
   fields, if present, are used from the Descriptor.

   Copy-Forward creates a copy of the packet and then forwards it in
   accordance to the nexthop value.




Matsushima, et al.      Expires December 20, 2018              [Page 60]


Internet-Draft              DMM FPC Protocol                   June 2018


                      |
                      +-[drop-template]
                      ...
                      |
                      +-[rewrite-template]
                      |     +-[Extensible: True]
                      |     +-[ip-prefix-template]
                      |     +-[pmip-traffic-selector]
                      |     +-[rfc5777-classifier]
                      ...
                      |
                      +-[copy-forward-template]
                      |     +-[Extensible: True]
                      |     +-[next-hop:]

                        Figure 33: Action Templates

6.5.  Quality of Service Action Templates

   PMIP QoS is specified in [RFC7222].

       |
       +-[qos-template]
       |     +-[Extensible: True]
       |     +-[(dscp) trafficclass]
       |     +-[pmip-qos]
       |     |     +-[(Unsigned 32) per-mn-agg-max-dl]
       |     |     +-[(Unsigned 32) per-mn-agg-max-ul]
       |     |     +-[per-session-agg-max-dl]
       |     |     |    +-[(Unsigned 32) max-rate:]
       |     |     |    +-[(Boolean) service-flag:]
       |     |     |    +-[(Boolean) exclude-flag:]
       |     |     +-[per-session-agg-max-ul]
       |     |     |    +-[(Unsigned 32) max-rate:]
       |     |     |    +-[(Boolean) service-flag:]
       |     |     |    +-[(Boolean) exclude-flag:]
       |     |     +-[allocation-retention-priority]
       |     |     |    +-[(Unsigned 8) priority-level:]
       |     |     |    +-[(Enumeration) preemption-capability:]
       |     |     |    +-[(Enumeration) preemption-vulnerability:]
       |     |     +-[(Unsigned 32) agg-max-dl]
       |     |     +-[(Unsigned 32) agg-max-ul]
       |     |     +-[(Unsigned 32) gbr-dl]
       |     |     +-[(Unsigned 32) gbr-ul]

                         Figure 34: QoS Templates





Matsushima, et al.      Expires December 20, 2018              [Page 61]


Internet-Draft              DMM FPC Protocol                   June 2018


6.6.  PMIP Command-Set

   The following Command Set values are supported for IETF PMIP.

   o  assign-ip - Assign the IP Address for the mobile session.

   o  assign-dpn - Assign the Data-plane Node.

   o  session - Assign values for the Session Level.

   o  uplink - Command applies to uplink.

   o  downlink - Command applies to downlink.

6.7.  3GPP Specific Templates and Command-Set

   3GPP support is optional and detailed in this section.  The following
   acronyms are used:

   APN-AMBR:  Access Point Name Aggregate Maximum Bit Rate

   UE-AMBR:  User Equipment Aggregate Maximum Bit Rate

   QCI:  QoS Class Identifier

   EBI:  EPS Bearer Identity

   LBI:  Linked Bearer Identity

   IMSI:  International Mobile Subscriber Identity

   TFT:  Traffic Flow Template (TFT)

   Generally, 3GPP QoS values should use the qos-template.  Note: User
   Equipment Aggregate Maximum Bit Rate (UE-AMBR) maps to the per-mn-
   agg-max-dl and per-mn-agg-max-ul.















Matsushima, et al.      Expires December 20, 2018              [Page 62]


Internet-Draft              DMM FPC Protocol                   June 2018


                      |
                      +-[ MN-Policy-Template ]
                      |     +-[(Unsigned 64) imsi:]
                      ...
                      +-[tunnel-template]
                      |     +-[Extensible: True]
                      |     +-[(unsigned 4) ebi:]
                      |     +-[(unsigned 4) lbi]
                      ...
                      +-[qos-template]
                      |     +-[Extensible: True]
                      |     +-[(unsigned 4) qos-class-identifier]
                      |     +-[(Unsigned 32) ue-agg-max-bitrate]
                      |     +-[(Unsigned 32) apn-agg-max-bitrate]
                      ...

                    Figure 35: 3GPP Mobility Templates

            |
            +-[ packet-filter ]
            |     +-[Extensible: True]
            |     +-[(Unsigned 8) identifier:]
            |     +-[Contents:] <List>
            |     |     +-[(ip-address) ipv4-ipv6-local]
            |     |     +-[(ipv6-prefix) ipv6-prefix-local]
            |     |     +-[(ip-address) ipv4-ipv6-remote]
            |     |     +-[(ipv6-prefix) ipv6-prefix-remote]
            |     |     +-[(Unsigned 8) protocol-next-header]
            |     |     +-[(Unsigned 16) local-port]
            |     |     +-[local-port-range]
            |     |     |      +-[(Unsigned 16) local-port-lo]
            |     |     |      +-[(Unsigned 16) local-port-hi]
            |     |     +-[(Unsigned 16) remote-port]
            |     |     +-[remote-port-range]
            |     |     |      +-[(Unsigned 16) remote-port-lo]
            |     |     |      +-[(Unsigned 16) remote-port-hi]
            |     |     +-[(Unsigned 32) sec-parameter-index]
            |     |     +-[(dscp) traffic-class]
            |     |     +-[traffic-class-range]
            |     |     |      +-[(dscp) traffic-class-lo]
            |     |     |      +-[(dscp) traffic-class-hi]
            |     |     +-[(dscp) flow-label]
            ...

            Figure 36: 3GPP Packet Filter Template (Descriptor)

   The following Command Set values are supported for 3GPP.




Matsushima, et al.      Expires December 20, 2018              [Page 63]


Internet-Draft              DMM FPC Protocol                   June 2018


   o  assign-ip - Assign the IP Address for the mobile session.

   o  assign-fteid-ip - Assign the Fully Qualified TEID (F-TEID) LOCAL
      IP address.

   o  assign-fteid-teid - Assign the Fully Qualified TEID (F-TEID) LOCAL
      TEID.

   o  session - Assign values for the Session Level.  When this involves
      'assign-fteid-ip' and 'assign-fteid-teid', the values are part of
      the default bearer.

   o  uplink - Command applies to uplink.

   o  downlink - Command applies to downlink.

   o  assign-dpn - Assign the Data-plane Node.

7.  Implementation Status

   Three FPC Agent implementations have been made to date.  The first
   was based upon Version 03 of the draft and followed Model 1.  The
   second follows Version 04 of the document.  Both implementations were
   OpenDaylight plug-ins developed in Java by Sprint.  Version 04 is now
   primarily enhanced by GS Labs.  Version 03 was known as fpcagent and
   version 04's implementation is simply referred to as 'fpc'.  A third
   has been developed on an ONOS Controller for use in MCORD projects.

   fpcagent's intent was to provide a proof of concept for FPC Version
   03 Model 1 in January 2016 and research various errors, corrections
   and optimizations that the Agent could make when supporting multiple
   DPNs.

   As the code developed to support OpenFlow and a proprietary DPN from
   a 3rd party, several of the advantages of a multi-DPN Agent became
   obvious including the use of machine learning to reduce the number of
   Flows and Policy entities placed on the DPN.  This work has driven
   new efforts in the DIME WG, namely Diameter Policy Groups
   [I-D.bertz-dime-policygroups].

   A throughput performance of tens per second using various NetConf
   based solutions in OpenDaylight made fpcagent, based on version 03,
   undesirable for call processing.  The RPC implementation improved
   throughput by an order of magnitude but was not useful based upon
   FPC's Version 03 design using two information models.  During this
   time the features of version 04 and its converged model became
   attractive and the fpcagent project was closed in August 2016.




Matsushima, et al.      Expires December 20, 2018              [Page 64]


Internet-Draft              DMM FPC Protocol                   June 2018


   fpcagent will no longer be developed and will remain a proprietary
   implementation.

   The learnings of fpcagent has influenced the second project, fpc.
   Fpc is also an OpenDaylight project but is an open source release as
   the Opendaylight FpcAgent plugin (https://wiki.opendaylight.org/view/
   Project_Proposals:FpcAgent).  This project is scoped to be a fully
   compliant FPC Agent that supports multiple DPNs including those that
   communicate via OpenFlow.  The following features present in this
   draft and others developed by the FPC development team have already
   led to an order of magnitude improvement.

       Migration of non-realtime provisioning of entities such as
       topology and policy allowed the implementation to focus only on
       the rpc.

       Using only 5 messages and 2 notifications has also reduced
       implementation time.

       Command Sets, an optional feature in this specification, have
       eliminated 80% of the time spent determining what needs to be
       done with a Context during a Create or Update operation.

       Op Reference is an optional feature modeled after video delivery.
       It has reduced unnecessary cache lookups.  It also has the
       additional benefit of allowing an Agent to become cacheless and
       effectively act as a FPC protocol adapter remotely with multi-DPN
       support or co-located on the DPN in a single-DPN support model.

       Multi-tenant support allows for Cache searches to be partitioned
       for clustering and performance improvements.  This has not been
       capitalized upon by the current implementation but is part of the
       development roadmap.

       Use of Contexts to pre-provision policy has also eliminated any
       processing of Ports for DPNs which permitted the code for
       CONFIGURE and CONF_BUNDLE to be implemented as a simple nested
       FOR loops (see below).

   Initial v04 performance results without code optimizations or tuning
   allow reliable provisioning of 1K FPC Mobility-Contexts processed per
   second on a 12 core server.  This results in 2x the number of
   transactions on the southbound interface to a proprietary DPN API on
   the same machine.

   fpc currently supports the following:

                           1 proprietary DPN API



Matsushima, et al.      Expires December 20, 2018              [Page 65]


Internet-Draft              DMM FPC Protocol                   June 2018


                           Policy and Topology as defined in this
                           specification using OpenDaylight North Bound
                           Interfaces such as NetConf and RestConf

                           CONFIG and CONF_BUNDLE (all operations)

                           DPN assignment, Tunnel allocations and IPv4
                           address assignment by the Agent or Client.

                           Immediate Response is always an
                           OK_NOTIFY_FOLLOWS.








































Matsushima, et al.      Expires December 20, 2018              [Page 66]


Internet-Draft              DMM FPC Protocol                   June 2018


        assignment system (receives rpc call):
          perform basic operation integrity check
          if CONFIG then
            goto assignments
            if assignments was ok then
              send request to activation system
              respond back to client with assignment data
            else
              send back error
            end if
          else if CONF_BUNDLE then
            for each operation in bundles
            goto assignments
            if assignments was ok then
              hold onto data
            else
              return error with the assignments that occurred in
                prior operations (best effort)
            end if
            end for
            send bundles to activation systems
          end if

        assignments:
          assign DPN, IPv4 Address and/or tunnel info as required
          if an error occurs undo all assignments in this operation
          return result

        activation system:
          build cache according to op-ref and operation type
          for each operation
            for each Context
              for each DPN / direction in Context
                perform actions on DPN according to Command Set
              end for
            end for
          end for
          commit changes to in memory cache
          log transaction for tracking and notification
                                        (CONFIG_RESULT_NOTIFY)

                        Figure 37: fpc pseudo code

   For further information please contact Lyle Bertz who is also a co-
   author of this document.

   NOTE: Tenant support requires binding a Client ID to a Tenant ID (it
   is a one to many relation) but that is outside of the scope of this



Matsushima, et al.      Expires December 20, 2018              [Page 67]


Internet-Draft              DMM FPC Protocol                   June 2018


   specification.  Otherwise, the specification is complete in terms of
   providing sufficient information to implement an Agent.

8.  Security Considerations

   Detailed protocol implementations for DMM Forwarding Policy
   Configuration must ensure integrity of the information exchanged
   between a FPC Client and a FPC Agent.  Required Security Associations
   may be derived from co-located functions, which utilize the FPC
   Client and FPC Agent respectively.

   The YANG modules defined in this memo are designed to be accessed via
   the NETCONF [RFC6241] or RESTCONF [RFC8040] protocol.  The lowest
   NETCONF layer is the secure transport layer and the mandatory-to-
   implement secure transport is SSH [RFC6242].

   The information model defined in the memo is designed to be access by
   protocols specified in extensions to this document or, if using the
   YANG modules, as described above.

   There are a number of data nodes defined which are
   writable/creatable/deletable.  These data nodes may be considered
   sensitive or vulnerable in some network environments.  Write
   operations (e.g., a NETCONF edit-config) to these data nodes without
   proper protection can have a negative effect on network operations.
   These are the subtrees and data nodes and their sensitivity/
   vulnerability:

      Nodes under the Policy tree provide generic policy enforcement and
      traffic classification.  They can be used to block or permit
      traffic.  If this portion of the model was to be compromised it
      may be used to block, identify or permit traffic that was not
      intended by the Tenant or FPC Client.

      Nodes under the Topology tree provide definition of the Tenant's
      forwarding topology.  Any compromise of this information will
      provide topology information that could be used for subsequent
      attack vectors.  Removal of topology can limit services.

      Mobility-Context provides runtime only information and manipulated
      by remote procedure calls.  The unwanted deletion or removal of
      such information would deny users service or provide services to
      unauthorized parties.

   Some of the readable data nodes defined may be considered sensitive
   or vulnerable in some network environments.  It is thus important to
   control read access (e.g., via get, get-config, or notification) to




Matsushima, et al.      Expires December 20, 2018              [Page 68]


Internet-Draft              DMM FPC Protocol                   June 2018


   these data nodes.  These are the subtrees and data nodes and their
   sensitivity/vulnerability:

      IP address assignments in the Mobility-Context along with their
      associated tunnel configurations/identifiers (from the FPC base
      module)

      Internaitonal Mobile Subscriber Identity (IMSI) and bearer
      identifiers in the Context when using the FPC base model

   Some of the RPC operations defined may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control access to these operations.  These are the operations and
   their sensitivity/vulnerability:

      Configure sends Mobility-Context information which can include
      information of a sensitive or vulnerable nature in some network
      environments as described above.

      Monitor related RPC operations do not specifically provide
      sensitive or vulnerable information but care must be taken by
      users to avoid identifier values that expose sensitive or
      vulnerable information.

      Notifications MUST be treated with same level of protection and
      scrutiny as the operations they correspond to.  For example, a
      Configure-Result-Notification provides the same information that
      is sent as part of the input and output of the Configure RPC
      operation.

   General usage of FPC MUST consider the following:

      FPC Naming Section 4.5 permits arbitrary string values but a user
      MUST avoid placing sensitive or vulnerable information in those
      values.

      Policies that are very narrow and permit the identification of
      specific traffic, e.g. that of a single user, SHOULD be avoided.

9.  IANA Considerations

   This document registers six URIs in the "IETF XML Registry"
   [RFC3688].  Following the format in RFC 3688, the following
   registrations have been made.

       URI: urn:ietf:params:xml:ns:yang:ietf-dmm-fpc
       Registrant Contact: The DMM WG of the IETF.
       XML: N/A, the requested URI is an XML namespace.



Matsushima, et al.      Expires December 20, 2018              [Page 69]


Internet-Draft              DMM FPC Protocol                   June 2018


       URI: urn:ietf:params:xml:ns:yang:ietf-dmm-pmip-qos
       Registrant Contact: The DMM WG of the IETF.
       XML: N/A, the requested URI is an XML namespace.

       URI: urn:ietf:params:xml:ns:yang:ietf-dmm-traffic-selector-types
       Registrant Contact: The DMM WG of the IETF.
       XML: N/A, the requested URI is an XML namespace.

       URI: urn:ietf:params:xml:ns:yang:ietf-dmm-fpc-settingsext
       Registrant Contact: The DMM WG of the IETF.
       XML: N/A, the requested URI is an XML namespace.

      URI: urn:ietf:params:xml:ns:yang:ietf-diam-trafficclassifier
      Registrant Contact: The DMM WG of the IETF.
      XML: N/A, the requested URI is an XML namespace.

   This document registers the following YANG modules in the "YANG
   Module Names" registry [RFC6020].

         name:         ietf-dmm-fpc
         namespace:    urn:ietf:params:xml:ns:yang:ietf-dmm-fpc
         prefix:       fpc
         reference:    TBD1

         name:         ietf-dmm-pmip-qos
         namespace:    urn:ietf:params:xml:ns:yang:ietf-dmm-pmip-qos
         prefix:       qos-pmip
         reference:    TBD2

         name:         ietf-dmm-traffic-selector-types
         namespace:    urn:ietf:params:xml:ns:yang:
           ietf-dmm-traffic-selector-types
         prefix:       traffic-selectors
         reference:    TBD3

         name:         ietf-dmm-fpc-settingsext
         namespace:    urn:ietf:params:xml:ns:yang:
           ietf-dmm-fpc-settingsext
         prefix:       fpcbase
         reference:    TBD4

           name:         ietf-diam-trafficclassifier
           namespace:    urn:ietf:params:xml:ns:yang:
           ietf-diam-trafficclassifier
           prefix:       diamclassifier
           reference:    TBD5





Matsushima, et al.      Expires December 20, 2018              [Page 70]


Internet-Draft              DMM FPC Protocol                   June 2018


10.  Work Team Participants

   Participants in the FPSM work team discussion include Satoru
   Matsushima, Danny Moses, Sri Gundavelli, Marco Liebsch, Pierrick
   Seite, Alper Yegin, Carlos Bernardos, Charles Perkins and Fred
   Templin.

11.  References

11.1.  Normative References

   [I-D.ietf-6man-segment-routing-header]
              Previdi, S., Filsfils, C., Leddy, J., Matsushima, S., and
              d. daniel.voyer@bell.ca, "IPv6 Segment Routing Header
              (SRH)", draft-ietf-6man-segment-routing-header-13 (work in
              progress), May 2018.

   [I-D.ietf-spring-segment-routing-mpls]
              Bashandy, A., Filsfils, C., Previdi, S., Decraene, B.,
              Litkowski, S., and R. Shakir, "Segment Routing with MPLS
              data plane", draft-ietf-spring-segment-routing-mpls-14
              (work in progress), June 2018.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC5777]  Korhonen, J., Tschofenig, H., Arumaithurai, M., Jones, M.,
              Ed., and A. Lior, "Traffic Classification and Quality of
              Service (QoS) Attributes for Diameter", RFC 5777,
              DOI 10.17487/RFC5777, February 2010,
              <https://www.rfc-editor.org/info/rfc5777>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <https://www.rfc-editor.org/info/rfc6020>.

   [RFC6088]  Tsirtsis, G., Giarreta, G., Soliman, H., and N. Montavont,
              "Traffic Selectors for Flow Bindings", RFC 6088,
              DOI 10.17487/RFC6088, January 2011,
              <https://www.rfc-editor.org/info/rfc6088>.

   [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
              RFC 6991, DOI 10.17487/RFC6991, July 2013,
              <https://www.rfc-editor.org/info/rfc6991>.




Matsushima, et al.      Expires December 20, 2018              [Page 71]


Internet-Draft              DMM FPC Protocol                   June 2018


   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8072]  Bierman, A., Bjorklund, M., and K. Watsen, "YANG Patch
              Media Type", RFC 8072, DOI 10.17487/RFC8072, February
              2017, <https://www.rfc-editor.org/info/rfc8072>.

   [RFC8300]  Quinn, P., Ed., Elzur, U., Ed., and C. Pignataro, Ed.,
              "Network Service Header (NSH)", RFC 8300,
              DOI 10.17487/RFC8300, January 2018,
              <https://www.rfc-editor.org/info/rfc8300>.

   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/info/rfc8342>.

11.2.  Informative References

   [I-D.bertz-dime-policygroups]
              Bertz, L. and M. Bales, "Diameter Policy Groups and Sets",
              draft-bertz-dime-policygroups-05 (work in progress),
              December 2017.

   [I-D.ietf-dmm-deployment-models]
              Gundavelli, S. and S. Jeon, "DMM Deployment Models and
              Architectural Considerations", draft-ietf-dmm-deployment-
              models-04 (work in progress), May 2018.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/info/rfc3688>.

   [RFC3958]  Daigle, L. and A. Newton, "Domain-Based Application
              Service Location Using SRV RRs and the Dynamic Delegation
              Discovery Service (DDDS)", RFC 3958, DOI 10.17487/RFC3958,
              January 2005, <https://www.rfc-editor.org/info/rfc3958>.

   [RFC5213]  Gundavelli, S., Ed., Leung, K., Devarapalli, V.,
              Chowdhury, K., and B. Patil, "Proxy Mobile IPv6",
              RFC 5213, DOI 10.17487/RFC5213, August 2008,
              <https://www.rfc-editor.org/info/rfc5213>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.



Matsushima, et al.      Expires December 20, 2018              [Page 72]


Internet-Draft              DMM FPC Protocol                   June 2018


   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <https://www.rfc-editor.org/info/rfc6242>.

   [RFC7222]  Liebsch, M., Seite, P., Yokota, H., Korhonen, J., and S.
              Gundavelli, "Quality-of-Service Option for Proxy Mobile
              IPv6", RFC 7222, DOI 10.17487/RFC7222, May 2014,
              <https://www.rfc-editor.org/info/rfc7222>.

   [RFC7333]  Chan, H., Ed., Liu, D., Seite, P., Yokota, H., and J.
              Korhonen, "Requirements for Distributed Mobility
              Management", RFC 7333, DOI 10.17487/RFC7333, August 2014,
              <https://www.rfc-editor.org/info/rfc7333>.

   [RFC7660]  Bertz, L., Manning, S., and B. Hirschman, "Diameter
              Congestion and Filter Attributes", RFC 7660,
              DOI 10.17487/RFC7660, October 2015,
              <https://www.rfc-editor.org/info/rfc7660>.

Appendix A.  YANG Data Model for the FPC protocol

   This section provides a type mapping for FPC structures in YANG.
   When being mapped to a specific information such as YANG the data
   type MAY change.

   Keys for Actions, Descriptors, Rules, Policies, DPNs, Domains and
   Mobility-Contexts are specified as FPC-Identity which follows rules
   according to Section 4.5.

   Action and Descriptor Templates are mapped as choices.  This was done
   to ensure no duplication of Types and avoid use of identityref for
   typing.

   Policy Expressions are provided as default values.  NOTE that a
   static value CANNOT be supported in YANG.

   Mapping of templates to YANG are performed as follows:

      Value is defined as a choice statement for extensibility and
      therefore a type value is not necessary to discriminated types

      Generic attributes are distinguished by the "Settings" type and
      holds ANY value.  It is an any data node under configurations.

   The CONFIGURE and CONFIGURE-RESULT-NOTIFICATION use the yang-patch-
   status which is a container for edits.  This was done to maximize
   YANG reuse.




Matsushima, et al.      Expires December 20, 2018              [Page 73]


Internet-Draft              DMM FPC Protocol                   June 2018


   In the configure rpc, operation-id is mapped to patch-id and in an
   edit the edit-type is mapped to operation.

   The Result-Status attribute is mapped to the 'ok' (empty leaf) or
   errors structure.

   The Policy-Status is mapped to entity-state to reduce YANG size.

   Five modules are defined:

   o  ietf-dmm-fpc (fpc) - Defines the base model and messages for FPC
      that are meant to be static in FPC.

   o  ietf-dmm-fpc-settingsext - A FPC module that defines the
      information model elements that are likely to be extended in FPC.

   o  ietf-pmip-qos (pmip-qos) - Defines proxy mobile IPv6 QoS
      parameters per RFC 7222

   o  ietf-trafficselectors-types (traffic-selectors) - Defines Traffic
      Selectors per [RFC6088]

   o  ietf-diam-trafficclassifier (diamclassifier) - Defines the
      Classifier per [RFC5777]

   All modules defined in this specification make use of (import) ietf-
   inet-types as defined in [RFC6991].

   ietf-dmm-fpc-settingsext and ietf-diam-trafficclassifier make use of
   (imports) ietf-yang-types as defined in [RFC6991].

   ietf-dmm-fpc imports the restconf (ietf-restconf) [RFC8040] and yang
   patch (ietf-yang-patch) [RFC8072] modules.

   ietf-pmip-qos and ietf-dmm-fpc-settings import the trafficselector
   from the ietf-traffic-selector-types module.

   ietf-dmm-fpc-settings also imports the qosattribute (ietf-pmip-qos)
   and classifier (ietf-diam-trafficclassifier).

   ietf-dmm-fpc-settingsext groups various settings, actions and
   descriptors and is used by the fpc module (ietf-dmm-fpc).

   The following groupings are intended for reuse (import) by other
   modules.

   o  qosoption (ietf-qos-pmip module)




Matsushima, et al.      Expires December 20, 2018              [Page 74]


Internet-Draft              DMM FPC Protocol                   June 2018


   o  qosattribute (ietf-qos-pmip module)

   o  qosoption (ietf-qos-pmip module)

   o  Allocation-Retention-Priority-Value (ietf-qos-pmip module)

   o  trafficselector (ietf-traffic-selector-types)

   o  classifier (ietf-diam-trafficclassifier)

   o  packet-filter (ietf-dmm-fpc-settingsext)

   o  instructions (ietf-dmm-fpc-settingsext)

   o  fpc-descriptor-value (ietf-dmm-fpc-settingsext)

   o  fpc-action-value (ietf-dmm-fpc-settingsext)

   The YANG modules in this document conform to the Network Management
   Datastore Architecture (NMDA) defined in [RFC8342].

   DPNs conformant to NMDA MAY only have policies, installed policies,
   topology, domains and mobility session information that has been
   assigned to it in its intended and operational datastores.  What is
   housed in the operational datastore MAY be determined on a per DPN
   basis and using the Entity-Status as a guideline based upon tradeoffs
   described in Section 4.6.

   ServiceGroups are not expected to appear in operational datastores of
   DPNs as they remain in and are used by FPC Agents and Clients.  They
   MAY be operationally present in DNS when using the Dynamic Delegation
   and Discovery System (DDDS) as defined in [RFC3958] or the
   operational datastore of systems that provide equivalent
   functionality.

A.1.  FPC YANG Model

   This module defines the information model and protocol elements
   specified in this document.

   This module references [RFC6991], [RFC8040] and the fpc-settingsext
   module defined in this document.

   <CODE BEGINS> file "ietf-dmm-fpc@2018-05-17.yang"
   module ietf-dmm-fpc {
     yang-version 1.1;
       namespace "urn:ietf:params:xml:ns:yang:ietf-dmm-fpc";
       prefix fpc;



Matsushima, et al.      Expires December 20, 2018              [Page 75]


Internet-Draft              DMM FPC Protocol                   June 2018


       import ietf-inet-types { prefix inet;
           revision-date 2013-07-15; }
       import ietf-dmm-fpc-settingsext { prefix fpcbase;
           revision-date 2018-05-17; }
       import ietf-diam-trafficclassifier { prefix rfc5777;
           revision-date 2018-05-17; }
       import ietf-restconf { prefix rc;
           revision-date 2017-01-26; }
       import ietf-yang-patch { prefix ypatch;
           revision-date 2017-02-22; }

       organization "IETF Distributed Mobility Management (DMM)
         Working Group";

       contact
          "WG Web:   <http://tools.ietf.org/wg/netmod/>
           WG List:  <mailto:netmod@ietf.org>

           WG Chair: Dapeng Liu
                     <mailto:maxpassion@gmail.com>

           WG Chair: Jouni Korhonen
                     <mailto:jouni.nospam@gmail.com>

           Editor:   Satoru Matsushima
                     <mailto:satoru.matsushima@g.softbank.co.jp>

           Editor:   Lyle Bertz
                     <mailto:lylebe551144@gmail.com>";

       description
       "This module contains YANG definition for
        Forwarding Policy Configuration Protocol (FPCP).

        Copyright (c) 2016 IETF Trust and the persons identified as the
        document authors. All rights reserved.

        This document is subject to BCP 78 and the IETF Trust's Legal
        Provisions Relating to IETF Documents
        (http://trustee.ietf.org/license-info) in effect on the date of
        publication of this document. Please review these documents
        carefully, as they describe your rights and restrictions with
        respect to this document. Code Components extracted from this
        document must include Simplified BSD License text as described
        in Section 4.e of the Trust Legal Provisions and are provided
        without warranty as described in the Simplified BSD License.";

       revision 2018-05-17 {



Matsushima, et al.      Expires December 20, 2018              [Page 76]


Internet-Draft              DMM FPC Protocol                   June 2018


       description "Initial Revision.";
       reference "draft-ietf-dmm-fpc-cpdp-10";
     }

       //General Structures
       grouping templatedef {
           leaf extensible {
               type boolean;
               description "Indicates if the template is extensible";
           }
           leaf-list static-attributes {
               type string;
               description "Attribute (Name) whose value cannot
                   change";
           }
           leaf-list mandatory-attributes {
               type string;
               description "Attribute (Name) of optional attributes
                 that MUST be present in instances of this tempplate.";
           }
           leaf entity-state {
               type enumeration {
                   enum initial {
                       description "Inital Configuration";
                   }
                   enum partially-configured {
                       description "Partial Configuration";
                   }
                   enum configured {
                       description "Confgured";
                   }
                   enum active {
                       description "Active";
                   }
               }
               default initial;
               description "Entity State";
           }
           leaf version {
               type uint32;
               description "Template Version";
           }
           description "Teamplate Definition";
       }
       typedef fpc-identity {
           type union {
               type uint32;
               type instance-identifier;



Matsushima, et al.      Expires December 20, 2018              [Page 77]


Internet-Draft              DMM FPC Protocol                   June 2018


               type string;
           }
           description "FPC Identity";
       }
       grouping index {
           leaf index {
               type uint16;
               description "Index";
           }
           description "Index Value";
       }

       // Policy Structures
       grouping descriptor-template-key {
           leaf descriptor-template-key {
               type fpc:fpc-identity;
               mandatory true;
               description "Descriptor Key";
           }
           description "Descriptor-Template Key";
       }
       grouping action-template-key {
           leaf action-template-key {
               type fpc:fpc-identity;
               mandatory true;
               description "Action Key";
           }
           description "Action-Template Key";
       }
       grouping rule-template-key {
           leaf rule-template-key {
               type fpc:fpc-identity;
               mandatory true;
               description "Rule Identifier";
           }
           description "Rule Key";
       }
       grouping policy-template-key {
           leaf policy-template-key {
               type fpc:fpc-identity;
               mandatory true;
               description "Rule Identifier";
           }
           description "Rule Key";
       }

       grouping fpc-setting-value {
           anydata setting;



Matsushima, et al.      Expires December 20, 2018              [Page 78]


Internet-Draft              DMM FPC Protocol                   June 2018


           description "FPC Setting Value";
       }
       // Configuration / Settings
       grouping policy-configuration-choice {
              choice policy-configuration-value {
                   case descriptor-value {
                       uses fpcbase:fpc-descriptor-value;
                       description "Descriptor Value";
                   }
                   case action-value {
                       uses fpcbase:fpc-action-value;
                       description "Action Value";
                   }
                   case setting-value {
                       uses fpc:fpc-setting-value;
                       description "Setting";
                   }
                   description "Policy Attributes";
               }
               description "Policy Configuration Value Choice";
       }
       grouping policy-configuration {
           list policy-configuration {
               key index;
               uses fpc:index;
               uses fpc:policy-configuration-choice;
               description "Policy Configuration";
           }
           description "Policy Configuration Value";
       }
       grouping ref-configuration {
           uses fpc:policy-template-key;
           uses fpc:policy-configuration;
           uses fpc:templatedef;
           description "Policy-Configuration Entry";
       }

       // FPC Policy
       grouping policy-information-model {
         list action-template {
           key action-template-key;
           uses fpc:action-template-key;
           uses fpcbase:fpc-action-value;
           uses fpc:templatedef;
           description "Action Template";
         }
         list descriptor-template {
           key descriptor-template-key;



Matsushima, et al.      Expires December 20, 2018              [Page 79]


Internet-Draft              DMM FPC Protocol                   June 2018


           uses fpc:descriptor-template-key;
           uses fpcbase:fpc-descriptor-value;
           uses fpc:templatedef;
           description "Descriptor Template";
         }
         list rule-template {
           key rule-template-key;
           uses fpc:rule-template-key;
           leaf descriptor-match-type {
               type enumeration {
                   enum or {
                       value 0;
                       description "OR logic";
                   }
                   enum and {
                       value 1;
                       description "AND logic";
                   }
               }
               mandatory true;
               description "Type of Match (OR or AND) applied
                   to the descriptor-configurations";
           }
           list descriptor-configuration {
               key "descriptor-template-key";
               uses fpc:descriptor-template-key;
               leaf direction {
                   type rfc5777:direction-type;
                   description "Direction";
               }
               list attribute-expression {
                   key index;
                   uses fpc:index;
                   uses fpcbase:fpc-descriptor-value;
                   description "Descriptor Attributes";
               }
               uses fpc:fpc-setting-value;
               description "A set of Descriptor references";
           }
           list action-configuration {
               key "action-order";
               leaf action-order {
                   type uint32;
                   mandatory true;
                   description "Action Execution Order";
               }
               uses fpc:action-template-key;
               list attribute-expression {



Matsushima, et al.      Expires December 20, 2018              [Page 80]


Internet-Draft              DMM FPC Protocol                   June 2018


                   key index;
                   uses fpc:index;
                   uses fpcbase:fpc-action-value;
                   description "Action Attributes";
               }
               uses fpc:fpc-setting-value;
               description "A set of Action references";
           }
           uses fpc:templatedef;
           list rule-configuration {
               key index;
               uses fpc:index;
               uses fpc:policy-configuration-choice;
               description "Rule Configuration";
           }
           description "Rule Template";
         }
         list policy-template {
           key policy-template-key;
           uses fpc:policy-template-key;
           list rule-template {
               key "precedence";
               unique "rule-template-key";
               leaf precedence {
                   type uint32;
                   mandatory true;
                   description "Rule Precedence";
               }
               uses fpc:rule-template-key;
               description "Rule Entry";
           }
           uses fpc:templatedef;
           uses fpc:policy-configuration;
           description "Policy Template";
         }
         description "FPC Policy Structures";
       }

       // Topology Information Model
       identity role {
           description "Role";
       }
       grouping dpn-key {
           leaf dpn-key {
               type fpc:fpc-identity;
               description "DPN Key";
           }
           description "DPN Key";



Matsushima, et al.      Expires December 20, 2018              [Page 81]


Internet-Draft              DMM FPC Protocol                   June 2018


       }
       grouping role-key {
           leaf role-key {
               type identityref {
                   base "fpc:role";
               }
               mandatory true;
               description "Access Technology Role";
           }
           description "Access Technology Role key";
       }
       grouping interface-key {
           leaf interface-key{
               type fpc:fpc-identity;
               mandatory true;
               description "interface identifier";
           }
           description "Interface Identifier key";
       }
       identity interface-protocols {
           description "Protocol supported by the interface";
       }
       identity features {
           description "Protocol features";
       }

     // Mobility Context
     grouping mobility-context {
       leaf mobility-context-key {
         type fpc:fpc-identity;
         mandatory true;
         description "Mobility Context Key";
       }
       leaf-list delegating-ip-prefix {
           type inet:ip-prefix;
           description "IP Prefix";
       }
       leaf parent-context {
         type fpc:fpc-identity;
         description "Parent Mobility Context";
       }
       leaf-list child-context {
           type fpc:fpc-identity;
           description "Child Mobility Context";
       }
       container mobile-node {
           leaf-list ip-address {
               type inet:ip-address;



Matsushima, et al.      Expires December 20, 2018              [Page 82]


Internet-Draft              DMM FPC Protocol                   June 2018


               description "IP Address";
           }
           leaf imsi {
               type fpcbase:imsi-type;
               description "IMSI";
           }
           list mn-policy-configuration {
               key policy-template-key;
               uses fpc:ref-configuration;
               description "MN Policy Configuration";
           }
           description "Mobile Node";
       }
       container domain {
           leaf domain-key {
               type fpc:fpc-identity;
               description "Domain Key";
           }
           list domain-policy-settings {
               key policy-template-key;
               uses fpc:ref-configuration;
               description "MN Policy Configuration";
           }
           description "Domain";
       }
       list dpn {
           key dpn-key;
           uses fpc:dpn-key;
           list dpn-policy-configuration {
               key policy-template-key;
               uses fpc:ref-configuration;
               description "DPN Policy Configuration";
           }
           leaf role {
               type identityref {
                   base "fpc:role";
               }
               description "Role";
           }
           list service-data-flow {
               key identifier;
               leaf identifier {
                   type uint32;
                   description "Generic Identifier";
               }
               leaf service-group-key {
                   type fpc:fpc-identity;
                   description "Service Group Key";



Matsushima, et al.      Expires December 20, 2018              [Page 83]


Internet-Draft              DMM FPC Protocol                   June 2018


               }
               list interface {
                   key interface-key;
                   uses fpc:interface-key;
                   description "interface assigned";
               }
               list service-data-flow-policy-configuration {
                   key policy-template-key;
                   uses fpc:ref-configuration;
                   description "Flow Policy Configuration";
               }
               description "Service Dataflow";
           }
           description "DPN";
       }
       description "Mobility Context";
     }

     // Events, Probes & Notifications
     identity event-type {
       description "Base Event Type";
     }
     typedef event-type-id {
       type uint32;
       description "Event ID Type";
     }
     grouping monitor-key {
       leaf monitor-key {
         type fpc:fpc-identity;
         mandatory true;
         description "Monitor Key";
       }
       description "Monitor Id";
     }
     grouping monitor-config {
       uses fpc:templatedef;
       uses fpc:monitor-key;
       leaf target {
         type string;
         description "target";
       }
       leaf deferrable {
         type boolean;
         description "Indicates reports related to this
           config can be delayed.";
       }
       choice configuration {
         mandatory true;



Matsushima, et al.      Expires December 20, 2018              [Page 84]


Internet-Draft              DMM FPC Protocol                   June 2018


         leaf period {
             type uint32;
             description "Period";
         }
         case threshold-config {
           leaf low {
             type uint32;
             description "low threshold";
           }
           leaf hi {
             type uint32;
             description "high threshold";
           }
           description "Threshold Config Case";
         }
         leaf schedule {
             type uint32;
             description "Reporting Time";
         }
         leaf-list event-identities {
             type identityref {
               base "fpc:event-type";
             }
             description "Event Identities";
         }
         leaf-list event-ids {
             type uint32;
               description "Event IDs";
         }
         description "Event Config Value";
       }
       description "Monitor Configuration";
     }

     // Top Level Structures
     list tenant {
      key "tenant-key";
      leaf tenant-key {
           type fpc:fpc-identity;
           description "Tenant Key";
      }
      container topology-information-model {
        config false;
        list service-group {
           key "service-group-key role-key";
           leaf service-group-key {
               type fpc:fpc-identity;
               mandatory true;



Matsushima, et al.      Expires December 20, 2018              [Page 85]


Internet-Draft              DMM FPC Protocol                   June 2018


               description "Service Group Key";
           }
           leaf service-group-name {
               type string;
               description "Service Group Name";
           }
           uses fpc:role-key;
           leaf role-name {
               type string;
               mandatory true;
               description "Role Name";
           }
           leaf-list protocol {
             type identityref {
               base "interface-protocols";
             }
             min-elements 1;
             description "Supported protocols";
           }
           leaf-list feature {
               type identityref {
                   base "interface-protocols";
               }
               description "Supported features";
           }
           list service-group-configuration {
               key index;
               uses fpc:index;
               uses fpc:policy-configuration-choice;
               description "Settings";
           }
           list dpn {
               key dpn-key;
               uses fpc:dpn-key;
               min-elements 1;
               list referenced-interface {
                   key interface-key;
                   uses fpc:interface-key;
                   leaf-list peer-service-group-key {
                       type fpc:fpc-identity;
                       description "Peer Service Group";
                   }
                   description "Referenced Interface";
               }
               description "DPN";
           }
           description "Service Group";
       }



Matsushima, et al.      Expires December 20, 2018              [Page 86]


Internet-Draft              DMM FPC Protocol                   June 2018


       list dpn {
         key dpn-key;
         uses fpc:dpn-key;
         leaf dpn-name {
           type string;
           description "DPN name";
         }
         leaf dpn-resource-mapping-reference {
           type string;
           description "Reference to underlying DPN resource(s)";
         }
         leaf domain-key {
           type fpc:fpc-identity;
           description "Domains";
         }
         leaf-list service-group-key {
           type fpc:fpc-identity;
           description "Service Group";
         }
         list interface {
           key "interface-key";
           uses fpc:interface-key;
           leaf interface-name {
               type string;
               description "Service Endpoint Interface Name";
           }
           leaf role {
               type identityref {
                   base "fpc:role";
               }
               description "Roles supported";
           }
           leaf-list protocol {
             type identityref {
               base "interface-protocols";
             }
             description "Supported protocols";
           }
           list interface-configuration {
            key index;
            uses fpc:index;
            uses fpc:policy-configuration-choice;
            description "Interface settings";
          }
          description "DPN interfaces";
         }
         list dpn-policy-configuration {
           key policy-template-key;



Matsushima, et al.      Expires December 20, 2018              [Page 87]


Internet-Draft              DMM FPC Protocol                   June 2018


           uses fpc:ref-configuration;
           description "DPN Policy Configuration";
         }
         description "Set of DPNs";
       }
       list domain {
         key domain-key;
         leaf domain-key {
           type fpc:fpc-identity;
           mandatory true;
           description "Domain Key";
         }
         leaf domain-name {
           type string;
           description "Domain displayname";
         }
         list domain-policy-configuration {
           key policy-template-key;
           uses fpc:ref-configuration;
           description "Domain Configuration";
         }
         description "List of Domains";
       }
       container dpn-checkpoint {
           uses fpc:basename-info;
           description "DPN Checkpoint information";
       }
       container service-group-checkpoint {
           uses fpc:basename-info;
           description "Service Group Checkpoint information";
       }
       container domain-checkpoint {
           uses fpc:basename-info;
           description "Domain Checkpoint information";
       }
       description "FPC Topology grouping";
      }
      container policy-information-model {
           config false;
           uses fpc:policy-information-model;
           uses fpc:basename-info;
           description "Policy";
      }
      list mobility-context {
           key "mobility-context-key";
           config false;
           uses fpc:mobility-context;
           description "Mobility Context";



Matsushima, et al.      Expires December 20, 2018              [Page 88]


Internet-Draft              DMM FPC Protocol                   June 2018


      }
      list monitor {
           key monitor-key;
           config false;
           uses fpc:monitor-config;
           description "Monitor";
      }
      description "Tenant";
     }

       typedef agent-identifier {
           type fpc:fpc-identity;
           description "Agent Identifier";
       }
       typedef client-identifier {
           type fpc:fpc-identity;
           description "Client Identifier";
       }
       grouping basename-info {
             leaf basename {
               type fpc:fpc-identity;
               description "Rules Basename";
             }
             leaf base-checkpoint {
               type string;
               description "Checkpoint";
             }
             description "Basename Information";
       }

       // RPCs
       grouping client-id {
           leaf client-id {
               type fpc:client-identifier;
               mandatory true;
               description "Client Id";
           }
           description "Client Identifier";
       }
       grouping execution-delay {
           leaf execution-delay {
               type uint32;
               description "Execution Delay (ms)";
           }
           description "Execution Delay";
       }
       typedef ref-scope {
         type enumeration {



Matsushima, et al.      Expires December 20, 2018              [Page 89]


Internet-Draft              DMM FPC Protocol                   June 2018


           enum none {
             value 0;
             description "no references";
           }
           enum op {
             value 1;
             description "All references are intra-operation";
           }
           enum bundle {
             value 2;
             description "All references in exist in bundle";
           }
           enum storage {
             value 3;
             description "One or more references exist in storage.";
           }
           enum unknown {
             value 4;
             description "The location of the references are unknown.";
           }
         }
         description "Search scope for references in the operation.";
       }
       rpc configure {
           description "Configure RPC";
           input {
               uses client-id;
               uses execution-delay;
               uses ypatch:yang-patch;
           }
           output {
               uses ypatch:yang-patch-status;
           }
       }
       augment "/configure/input/yang-patch/edit" {
           leaf reference-scope {
               type fpc:ref-scope;
               description "Reference Scope";
           }
           uses fpcbase:instructions;
           description "yang-patch edit augments for configure rpc";
       }
       grouping subsequent-edits {
            list subsequent-edit {
              key edit-id;
              ordered-by user;

              description "Edit list";



Matsushima, et al.      Expires December 20, 2018              [Page 90]


Internet-Draft              DMM FPC Protocol                   June 2018


              leaf edit-id {
                type string;
                description "Arbitrary string index for the edit.";
              }

              leaf operation {
                type enumeration {
                  enum create {
                    description "Create";
                  }
                  enum delete {
                    description "Delete";
                  }
                  enum insert {
                    description "Insert";
                  }
                  enum merge {
                    description "Merge";
                  }
                  enum move {
                    description "Move";
                  }
                  enum replace {
                    description "Replace";
                  }
                  enum remove {
                    description
                      "Delete the target node if it currently exists.";
                  }
                }
                mandatory true;
                description
                  "The datastore operation requested";
              }

              leaf target {
                type ypatch:target-resource-offset;
                mandatory true;
                description
                  "Identifies the target data node";
              }

              leaf point {
               when "(../operation = 'insert' or ../operation = 'move')"
                + "and (../where = 'before' or ../where = 'after')" {
                  description
                    "This leaf only applies for 'insert' or 'move'
                     operations, before or after an existing entry.";



Matsushima, et al.      Expires December 20, 2018              [Page 91]


Internet-Draft              DMM FPC Protocol                   June 2018


                }
                type ypatch:target-resource-offset;
                description
                  "The absolute URL path for the data node";
              }

              leaf where {
               when "../operation = 'insert' or ../operation = 'move'" {
                  description
                    "This leaf only applies for 'insert' or 'move'
                     operations.";
                }
                type enumeration {
                  enum before {
                    description
                      "Insert or move a data node before.";
                  }
                  enum after {
                    description
                      "Insert or move a data node after.";
                  }
                 enum first {
                    description
                      "Insert or move a data node so it becomes ordered
                       as the first entry.";
                  }
                  enum last {
                    description
                      "Insert or move a data node so it becomes ordered
                       as the last entry.";
                  }
                }
                default last;
                description
                  "Identifies where a data resource will be inserted
                   or moved.";
              }

              anydata value {
                when "../operation = 'create' "
                   + "or ../operation = 'merge' "
                   + "or ../operation = 'replace' "
                   + "or ../operation = 'insert'" {
                  description
                    "The anydata 'value' is only used for 'create',
                     'merge', 'replace', and 'insert' operations.";
                }
                description



Matsushima, et al.      Expires December 20, 2018              [Page 92]


Internet-Draft              DMM FPC Protocol                   June 2018


                  "Value used for this edit operation.";
              }
            }
            description "Subsequent Edits";
       }
       augment "/configure/output/yang-patch-status/edit-status/edit/"
           + "edit-status-choice/ok" {
           leaf notify-follows {
               type boolean;
               description "Notify Follows Indication";
           }
           uses fpc:subsequent-edits;
           description "Configure output augments";
       }

       grouping op-header {
           uses client-id;
           uses execution-delay;
           leaf operation-id {
               type uint64;
               mandatory true;
               description "Operation Identifier";
           }
           description "Common Operation header";
       }
       grouping monitor-response {
           leaf operation-id {
               type uint64;
               mandatory true;
               description "Operation Identifier";
           }
           choice edit-status-choice {
                  description
                    "A choice between different types of status
                     responses for each 'edit' entry.";
                  leaf ok {
                    type empty;
                    description
                      "This 'edit' entry was invoked without any
                       errors detected by the server associated
                       with this edit.";
                  }
                  case errors {
                    uses rc:errors;
                    description
                      "The server detected errors associated with the
                       edit identified by the same 'edit-id' value.";
                  }



Matsushima, et al.      Expires December 20, 2018              [Page 93]


Internet-Draft              DMM FPC Protocol                   June 2018


           }
           description "Monitor Response";
       }

     // Common RPCs
     rpc register_monitor {
       description "Used to register monitoring of parameters/events";
       input {
         uses fpc:op-header;
         list monitor {
           key monitor-key;
           uses fpc:monitor-config;
           description "Monitor Configuration";
         }
       }
       output {
           uses fpc:monitor-response;
       }
     }
     rpc deregister_monitor {
       description "Used to de-register monitoring of
         parameters/events";
       input {
         uses fpc:op-header;
         list monitor {
           key monitor-key;
           uses fpc:monitor-key;
           min-elements 1;
           leaf send_data {
               type boolean;
               description "Indicates if NOTIFY with final data
                   is desired upon deregistration";
           }
           description "Monitor Identifier";
         }
       }
       output {
           uses fpc:monitor-response;
       }
     }
     rpc probe {
       description "Probe the status of a registered monitor";
       input {
         uses fpc:op-header;
         list monitor {
           key monitor-key;
           uses fpc:monitor-key;
           min-elements 1;



Matsushima, et al.      Expires December 20, 2018              [Page 94]


Internet-Draft              DMM FPC Protocol                   June 2018


           description "Monitor";
         }
       }
       output {
           uses fpc:monitor-response;
       }
     }

     // Notification Messages & Structures
     notification config-result-notification {
       uses ypatch:yang-patch-status;
       description "Configuration Result Notification";
     }
     augment "/config-result-notification" {
           uses fpc:subsequent-edits;
           description "config-result-notificatio augment";
     }

     identity notification-cause {
       description "Notification Cause";
     }
     identity subscribed-event-occurred {
       base "notification-cause";
       description "Subscribed Event Occurence";
     }
     identity low-threshold-crossed {
       base "notification-cause";
       description "Subscribed Event Occurence";
     }
     identity high-threshold-crossed {
       base "notification-cause";
       description "Subscribed Event Occurence";
     }
     identity periodic-report {
       base "notification-cause";
       description "Periodic Report";
     }
     identity scheduled-report {
       base "notification-cause";
       description "Scheduled Report";
     }
     identity probe {
       base "notification-cause";
       description "Probe";
     }
     identity deregistration-final-value {
       base "notification-cause";
       description "Probe";



Matsushima, et al.      Expires December 20, 2018              [Page 95]


Internet-Draft              DMM FPC Protocol                   June 2018


     }
     identity monitoring-suspension {
       base "notification-cause";
       description "Indicates monitoring suspension";
     }
     identity monitoring-resumption {
       base "notification-cause";
       description "Indicates that monitoring has resumed";
     }
     identity dpn-available {
       base "notification-cause";
       description "DPN Candidate Available";
     }
     identity dpn-unavailable {
       base "notification-cause";
       description "DPN Unavailable";
     }
     notification notify {
       leaf notification-id {
         type uint32;
         description "Notification Identifier";
       }
       leaf timestamp {
         type uint32;
         description "timestamp";
       }
       list report {
           key monitor-key;
           uses fpc:monitor-key;
           min-elements 1;
           leaf trigger {
               type identityref {
                   base "notification-cause";
               }
               description "Notification Cause";
           }
           choice value {
               case dpn-candidate-available {
                   leaf node-id {
                       type inet:uri;
                       description "Topology URI";
                   }
                   list supported-interface-list {
                       key role-key;
                       uses fpc:role-key;
                       description "Support Intefaces";
                   }
                   description "DPN Candidate Information";



Matsushima, et al.      Expires December 20, 2018              [Page 96]


Internet-Draft              DMM FPC Protocol                   June 2018


               }
               case dpn-unavailable {
                   leaf dpn-id {
                     type fpc:fpc-identity;
                     description "DPN Identifier for DPN Unavailable";
                   }
                   description "DPN Unavailable";
               }
               anydata report-value {
                   description "Any non integer report";
               }
               description "Report Value";
           }
           description "Report";
       }
       description "Notify Message";
     }
   }
   <CODE ENDS>

A.2.  FPC YANG Settings and Extensions Model

   This module defines the base data elements in FPC that are likely to
   be extended.

   This module references [RFC6991], ietf-trafficselector-types and
   ietf-pmip-qos modules.

   <CODE BEGINS> file "ietf-dmm-fpc-settingsext@2018-05-17.yang"
   module ietf-dmm-fpc-settingsext {
     yang-version 1.1;
     namespace "urn:ietf:params:xml:ns:yang:ietf-dmm-fpc-settingsext";
     prefix fpcbase;

       import ietf-inet-types { prefix inet;
           revision-date 2013-07-15; }
       import ietf-trafficselector-types { prefix traffic-selectors;
           revision-date 2018-05-17; }
       import ietf-yang-types { prefix ytypes;
           revision-date 2013-07-15; }
       import ietf-pmip-qos { prefix pmipqos;
           revision-date 2018-05-17; }
       import ietf-diam-trafficclassifier { prefix rfc5777;
           revision-date 2018-05-17; }

       organization "IETF Distributed Mobility Management (DMM)
         Working Group";




Matsushima, et al.      Expires December 20, 2018              [Page 97]


Internet-Draft              DMM FPC Protocol                   June 2018


       contact
          "WG Web:   <http://tools.ietf.org/wg/netmod/>
           WG List:  <mailto:netmod@ietf.org>

           WG Chair: Dapeng Liu
                     <mailto:maxpassion@gmail.com>

           WG Chair: Sri Gundavelli
                     <mailto:sgundave@cisco.com>

           Editor:   Satoru Matsushima
                     <mailto:satoru.matsushima@g.softbank.co.jp>

           Editor:   Lyle Bertz
                     <mailto:lylebe551144@gmail.com>";

       description
       "This module contains YANG definition for
        Forwarding Policy Configuration Protocol(FPCP).

         It contains Settings defintions as well as Descriptor and
         Action extensions.

        Copyright (c) 2016 IETF Trust and the persons identified as the
        document authors. All rights reserved.

        This document is subject to BCP 78 and the IETF Trust's Legal
        Provisions Relating to IETF Documents
        (http://trustee.ietf.org/license-info) in effect on the date of
        publication of this document. Please review these documents
        carefully, as they describe your rights and restrictions with
        respect to this document. Code Components extracted from this
        document must include Simplified BSD License text as described
        in Section 4.e of the Trust Legal Provisions and are provided
        without warranty as described in the Simplified BSD License.";

   revision 2018-05-17 {
       description "Initial Revision.";
       reference "draft-ietf-dmm-fpc-cpdp-10";
   }

       //Tunnel Information
        identity tunnel-type {
             description "Tunnel Type";
         }
         identity grev1 {
             base "fpcbase:tunnel-type";
             description "GRE v1";



Matsushima, et al.      Expires December 20, 2018              [Page 98]


Internet-Draft              DMM FPC Protocol                   June 2018


         }
         identity grev2 {
             base "fpcbase:tunnel-type";
             description "GRE v2";
         }
         identity ipinip {
             base "fpcbase:tunnel-type";
             description "IP in IP";
         }
         identity gtpv1 {
             base "fpcbase:tunnel-type";
             description "GTP version 1 Tunnel";
         }
         identity gtpv2 {
             base "fpcbase:tunnel-type";
             description "GTP version 2 Tunnel";
         }

       grouping tunnel-value {
         container tunnel-info {
           leaf tunnel-local-address {
               type inet:ip-address;
               description "local tunnel address";
           }
           leaf tunnel-remote-address {
               type inet:ip-address;
               description "remote tunnel address";
           }
           leaf mtu-size {
               type uint32;
               description "MTU size";
           }
           leaf tunnel {
               type identityref {
                   base "fpcbase:tunnel-type";
               }
           description "tunnel type";
           }
           leaf payload-type {
               type enumeration {
                   enum ipv4 {
                       value 0;
                       description "IPv4";
                   }
                   enum ipv6 {
                       value 1;
                       description "IPv6";
                   }



Matsushima, et al.      Expires December 20, 2018              [Page 99]


Internet-Draft              DMM FPC Protocol                   June 2018


                   enum dual {
                       value 2;
                       description "IPv4 and IPv6";
                   }
               }
               description "Payload Type";
           }
           leaf gre-key {
               type uint32;
               description "GRE_KEY";
           }
           container gtp-tunnel-info {
               leaf local-tunnel-identifier {
                   type uint32;
                   description "Tunnel Endpoint IDentifier (TEID)";
               }
               leaf remote-tunnel-identifier {
                   type uint32;
                   description "Tunnel Endpoint IDentifier (TEID)";
               }
               leaf sequence-numbers-enabled {
                   type boolean;
                   description "Sequence No. Enabled";
               }
               description "GTP Tunnel Information";
           }
           leaf ebi {
               type fpcbase:ebi-type;
               description "EPS Bearier Identifier";
           }
           leaf lbi {
               type fpcbase:ebi-type;
               description "Linked Bearier Identifier";
           }
           description "Tunnel Information";
         }
         description "Tunnel Value";
       }

     //////////////////////////////
     // DESCRIPTOR DEFINITIONS

       // From 3GPP TS 24.008 version 13.5.0 Release 13
         typedef packet-filter-direction {
             type enumeration {
               enum preRel7Tft {
                 value 0;
                 description "Pre-Release 7 TFT";



Matsushima, et al.      Expires December 20, 2018             [Page 100]


Internet-Draft              DMM FPC Protocol                   June 2018


               }
               enum uplink {
                 value 1;
                 description "uplink";
               }
               enum downlink {
                 value 2;
                 description "downlink";
               }
               enum bidirectional {
                 value 3;
                 description "bi-direcitonal";
               }
             }
             description "Packet Filter Direction";
         }
         typedef component-type-id {
             type uint8 {
               range "16 | 17 | 32 | 33 | 35 | 48 | 64 | 65 |"
               + " 80 | 81 | 96 | 112 | 128";
             }
             description "Specifies the Component Type";
         }
         grouping packet-filter {
           leaf direction {
               type fpcbase:packet-filter-direction;
               description "Filter Direction";
           }
           leaf identifier {
               type uint8 {
                 range "1..15";
               }
               description "Filter Identifier";
           }
           leaf evaluation-precedence {
               type uint8;
               description "Evaluation Precedence";
           }
           list contents {
             key component-type-identifier;
             description "Filter Contents";
             leaf component-type-identifier {
                 type fpcbase:component-type-id;
                 description "Component Type";
             }
             choice value {
               leaf ipv4-local {
                   type inet:ipv4-address;



Matsushima, et al.      Expires December 20, 2018             [Page 101]


Internet-Draft              DMM FPC Protocol                   June 2018


                   description "IPv4 Local Address";
               }
               leaf ipv6-prefix-local {
                   type inet:ipv6-prefix;
                   description "IPv6 Local Prefix";
               }
               leaf ipv4-ipv6-remote {
                   type inet:ip-address;
                   description "Ipv4 Ipv6 remote address";
               }
               leaf ipv6-prefix-remote {
                   type inet:ipv6-prefix;
                   description "IPv6 Remote Prefix";
               }
               leaf next-header {
                   type uint8;
                   description "Next Header";
               }
               leaf local-port {
                   type inet:port-number;
                   description "Local Port";
               }
               case local-port-range {
                 leaf local-port-lo {
                   type inet:port-number;
                   description "Local Port Min Value";
                 }
                 leaf local-port-hi {
                   type inet:port-number;
                   description "Local Port Max Value";
                 }
               }
               leaf remote-port {
                   type inet:port-number;
                   description "Remote Port";
               }
               case remote-port-range {
                 leaf remote-port-lo {
                   type inet:port-number;
                   description "Remote Por Min Value";
                 }
                 leaf remote-port-hi {
                   type inet:port-number;
                   description "Remote Port Max Value";
                 }
               }
               leaf ipsec-index {
                   type traffic-selectors:ipsec-spi;



Matsushima, et al.      Expires December 20, 2018             [Page 102]


Internet-Draft              DMM FPC Protocol                   June 2018


                   description "IPSec Index";
               }
               leaf traffic-class {
                   type inet:dscp;
                   description "Traffic Class";
               }
               case traffic-class-range {
                   leaf traffic-class-lo {
                     type inet:dscp;
                     description "Traffic Class Min Value";
                   }
                   leaf traffic-class-hi {
                     type inet:dscp;
                     description "Traffic Class Max Value";
                   }
               }
               leaf-list flow-label {
                   type inet:ipv6-flow-label;
                   description "Flow Label";
               }
               description "Component Value";
             }
           }
           description "Packet Filter";
         }

       grouping prefix-descriptor {
           leaf destination-ip {
             type inet:ip-prefix;
             description "Rule of destination IP";
           }
           leaf source-ip {
             type inet:ip-prefix;
             description "Rule of source IP";
           }
           description "Traffic descriptor based upon source/
             destination as IP prefixes";
       }

     grouping fpc-descriptor-value {
       choice descriptor-value {
         mandatory true;
         leaf all-traffic {
             type empty;
             description "admit any";
         }
         leaf no-traffic {
             type empty;



Matsushima, et al.      Expires December 20, 2018             [Page 103]


Internet-Draft              DMM FPC Protocol                   June 2018


             description "deny any";
         }
         case prefix-descriptor {
           uses fpcbase:prefix-descriptor;
           description "IP Prefix descriptor";
         }
         case pmip-selector {
           uses traffic-selectors:traffic-selector;
           description "PMIP Selector";
         }
         container rfc5777-classifier-template {
               uses rfc5777:classifier;
               description "RFC 5777 Classifier";
         }
         container packet-filter {
               uses fpcbase:packet-filter;
               description "Packet Filter";
         }
         case tunnel-info {
           uses fpcbase:tunnel-value;
           description "Tunnel Descriptor (only
               considers source info)";
         }
         description "Descriptor Value";
       }
       description "FPC Descriptor Values";
     }

       // Next Hop Structures
       typedef fpc-service-path-id {
           type uint32 {
               range "0..33554431";
           }
           description "SERVICE_PATH_ID";
       }
       typedef fpc-mpls-label {
           type uint32 {
             range "0..1048575";
           }
           description "MPLS label";
       }
       typedef segment-id {
           type string {
               length "16";
           }
           description "SR Segement Identifier";
       }
       grouping fpc-nexthop {



Matsushima, et al.      Expires December 20, 2018             [Page 104]


Internet-Draft              DMM FPC Protocol                   June 2018


           choice next-hop-value {
               leaf ip-address {
                   type inet:ip-address;
                   description "IP Value";
               }
               leaf mac-address {
                   type ytypes:mac-address;
                   description "MAC Address Value";
               }
               leaf service-path {
                   type fpcbase:fpc-service-path-id;
                   description "Service Path Value";
               }
               leaf mpls-path {
                   type fpcbase:fpc-mpls-label;
                   description "MPLS Value";
               }
               leaf nsh {
                   type string {
                       length "16";
                   }
                   description "Network Service Header";
               }
               leaf interface {
                   type uint16;
                   description "If (interface) Value";
               }
               leaf segment-identifier {
                   type fpcbase:segment-id;
                   description "Segment Id";
               }
               leaf-list mpls-label-stack {
                   type fpcbase:fpc-mpls-label;
                   description "MPLS Stack";
               }
               leaf-list mpls-sr-stack {
                   type fpcbase:fpc-mpls-label;
                   description "MPLS SR Stack";
               }
               leaf-list srv6-stack {
                   type fpcbase:segment-id;
                   description "Segment Id";
               }
               case tunnel-info {
                   uses fpcbase:tunnel-value;
                   description "Tunnel Descriptor (only
                   considers source info)";
               }



Matsushima, et al.      Expires December 20, 2018             [Page 105]


Internet-Draft              DMM FPC Protocol                   June 2018


               description "Value";
           }
           description "Nexthop Value";
       }

       //////////////////////////////
       // PMIP Integration         //
         typedef pmip-commandset {
               type bits {
                   bit assign-ip {
                     position 0;
                     description "Assign IP";
                   }
                   bit assign-dpn {
                     position 1;
                     description "Assign DPN";
                   }
                   bit session {
                     position 2;
                     description "Session Level";
                   }
                   bit uplink {
                     position 3;
                     description "Uplink";
                   }
                   bit downlink {
                     position 4;
                     description "Downlink";
                   }
               }
               description "PMIP Instructions";
           }
       ///////////////////////////////
       // 3GPP Integration         //

         // Type Defs
         typedef fpc-qos-class-identifier {
             type uint8 {
                 range "1..9";
             }
             description "QoS Class Identifier (QCI)";
         }
         typedef ebi-type {
           type uint8 {
             range "0..15";
           }
           description "EUTRAN Bearere Identifier (EBI) Type";
         }



Matsushima, et al.      Expires December 20, 2018             [Page 106]


Internet-Draft              DMM FPC Protocol                   June 2018


         typedef imsi-type {
             type uint64;
             description
                 "International Mobile Subscriber Identity (IMSI)
                   Value Type";
         }
         // Instructions
         typedef threegpp-instr {
           type bits {
             bit assign-ip {
               position 0;
               description "Assign IP Address/Prefix";
             }
             bit assign-fteid-ip {
               position 1;
               description "Assign FTEID-IP";
             }
             bit assign-fteid-teid {
               position 2;
               description "Assign FTEID-TEID";
             }
             bit session {
               position 3;
               description "Commands apply to the Session Level";
             }
             bit uplink {
               position 4;
               description "Commands apply to the Uplink";
             }
             bit downlink {
               position 5;
               description "Commands apply to the Downlink";
             }
             bit assign-dpn {
               position 6;
               description "Assign DPN";
             }
           }
           description "Instruction Set for 3GPP R11";
         }

       //////////////////////////////
       // ACTION VALUE AUGMENTS
       grouping fpc-action-value {
           choice action-value {
               mandatory true;
               leaf drop {
                   type empty;



Matsushima, et al.      Expires December 20, 2018             [Page 107]


Internet-Draft              DMM FPC Protocol                   June 2018


                   description "Drop Traffic";
               }
               container rewrite {
                   choice rewrite-value {
                       case prefix-descriptor {
                           uses fpcbase:prefix-descriptor;
                           description "IP Prefix descriptor";
                       }
                       case pmip-selector {
                           uses traffic-selectors:traffic-selector;
                           description "PMIP Selector";
                       }
                       container rfc5777-classifier-template {
                           uses rfc5777:classifier;
                           description "RFC 5777 Classifier";
                       }
                       description "Rewrite Choice";
                   }
                   description "Rewrite/NAT value";
               }
               container copy-forward-nexthop {
                       uses fpcbase:fpc-nexthop;
                       description "Copy Forward Value";
               }
               container nexthop {
                       uses fpcbase:fpc-nexthop;
                       description "NextHop Value";
               }
               case qos {
                   leaf trafficclass {
                       type inet:dscp;
                       description "Traffic Class";
                   }
                   uses pmipqos:qosattribute;
                   leaf qci {
                       type fpcbase:fpc-qos-class-identifier;
                       description "QCI";
                   }
                   leaf ue-agg-max-bitrate {
                       type uint32;
                       description "UE Aggregate Max Bitrate";
                   }
                   leaf apn-ambr {
                       type uint32;
                       description
                        "Access Point Name Aggregate Max Bit Rate";
                   }
                   description "QoS Attributes";



Matsushima, et al.      Expires December 20, 2018             [Page 108]


Internet-Draft              DMM FPC Protocol                   June 2018


               }
               description "Action Value";
           }
           description "FPC Action Value";
       }

     // Instructions
     grouping instructions {
       container command-set {
         choice instr-type {
           leaf instr-3gpp-mob {
               type fpcbase:threegpp-instr;
               description "3GPP GTP Mobility Instructions";
           }
           leaf instr-pmip {
               type pmip-commandset;
               description "PMIP Instructions";
           }
           description "Instruction Value Choice";
         }
         description "Instructions";
       }
       description "Instructions Value";
     }
   }
   <CODE ENDS>

A.3.  PMIP QoS Model

   This module defines the base protocol elements specified in this
   document.

   This module references [RFC6991].

   <CODE BEGINS> file "ietf-pmip-qos@2018-05-17.yang"
   module ietf-pmip-qos {
       yang-version 1.1;

       namespace
         "urn:ietf:params:xml:ns:yang:ietf-pmip-qos";

       prefix "qos-pmip";

       import ietf-inet-types {
         prefix inet;
         revision-date 2013-07-15;
       }
       import ietf-trafficselector-types { prefix traffic-selectors;



Matsushima, et al.      Expires December 20, 2018             [Page 109]


Internet-Draft              DMM FPC Protocol                   June 2018


           revision-date 2018-05-17; }

       organization "IETF Distributed Mobility Management (DMM)
         Working Group";

       contact
          "WG Web:   <http://tools.ietf.org/wg/netmod/>
           WG List:  <mailto:netmod@ietf.org>

           WG Chair: Dapeng Liu
                     <mailto:maxpassion@gmail.com>

           WG Chair: Sri Gundavelli
                     <mailto:sgundave@cisco.com>

           Editor:   Satoru Matsushima
                     <mailto:satoru.matsushima@g.softbank.co.jp>

           Editor:   Lyle Bertz
                     <mailto:lylebe551144@gmail.com>";

       description
         "This module contains a collection of YANG definitions for
        quality of service paramaters used in Proxy Mobile IPv6.

        Copyright (c) 2016 IETF Trust and the persons identified as the
        document authors. All rights reserved.

        This document is subject to BCP 78 and the IETF Trust's Legal
        Provisions Relating to IETF Documents
        (http://trustee.ietf.org/license-info) in effect on the date of
        publication of this document. Please review these documents
        carefully, as they describe your rights and restrictions with
        respect to this document. Code Components extracted from this
        document must include Simplified BSD License text as described
        in Section 4.e of the Trust Legal Provisions and are provided
        without warranty as described in the Simplified BSD License.";

     revision 2018-05-17 {
       description "Initial Revision.";
       reference "RFC 6088: Traffic Selectors for Flow Bindings";
     }

       // Type Definitions

       // QoS Option Field Type Definitions
     typedef sr-id {
       type uint8;



Matsushima, et al.      Expires December 20, 2018             [Page 110]


Internet-Draft              DMM FPC Protocol                   June 2018


         description
          "An 8-bit unsigned integer used for identifying the QoS
           Service Request.";
       }

       typedef traffic-class {
         type inet:dscp;
         description
           "Traffic Class consists of a 6-bit DSCP field followed by a
            2-bit reserved field.";
        reference
            "RFC 3289: Management Information Base for the
               Differentiated Services Architecture
             RFC 2474: Definition of the Differentiated Services Field
                       (DS Field) in the IPv4 and IPv6 Headers
             RFC 2780: IANA Allocation Guidelines For Values In
                       the Internet Protocol and Related Headers";
       }

       typedef operational-code {
         type enumeration {
           enum RESPONSE {
             value 0;
             description "Response to a QoS request";
           }
           enum ALLOCATE {
             value 1;
             description "Request to allocate QoS resources";
           }
           enum DE-ALLOCATE {
             value 2;
             description "Request to de-Allocate QoS resources";
           }
           enum MODIFY {
             value 3;
             description "Request to modify QoS parameters for a
                 previously negotiated QoS Service Request";
           }
           enum QUERY {
             value 4;
             description "Query to list the previously negotiated QoS
                 Service Requests that are still active";
           }
           enum NEGOTIATE {
             value 5;
             description "Response to a QoS Service Request with a
               counter QoS proposal";
           }



Matsushima, et al.      Expires December 20, 2018             [Page 111]


Internet-Draft              DMM FPC Protocol                   June 2018


         }
         description
          "The type of QoS request. Reserved values:   (6) to (255)
                   Currently not used.  Receiver MUST ignore the option
                   received with any value in this range.";
       }

     //Value definitions
     typedef Per-MN-Agg-Max-DL-Bit-Rate-Value {
         type uint32;
         description
             "The aggregate maximum downlink bit rate that is
             requested/allocated for all the mobile node's IP flows.
             The measurement units are bits per second.";
     }

      typedef Per-MN-Agg-Max-UL-Bit-Rate-Value {
         type uint32;
         description
           "The aggregate maximum uplink bit rate that is
               requested/allocated for the mobile node's IP flows.  The
               measurement units are bits per second.";
      }

      // Generic Structure for the uplink and downlink
      grouping Per-Session-Agg-Max-Bit-Rate-Value {
        leaf max-rate {
          type uint32;
          mandatory true;
          description
          "The aggregate maximum bit rate that is requested/allocated
        for all the IP flows associated with that mobility session.
        The measurement units are bits per second.";
        }
        leaf service-flag {
         type boolean;
         mandatory true;
         description
          "This flag is used for extending the scope of the
           target flows for Per-Session-Agg-Max-UL/DL-Bit-Rate
           from(UL)/to(DL) the mobile node's other mobility sessions
           sharing the same Service Identifier.";
         reference
           "RFC 5149 - Service Selection mobility option";
        }
        leaf exclude-flag {
          type boolean;
          mandatory true;



Matsushima, et al.      Expires December 20, 2018             [Page 112]


Internet-Draft              DMM FPC Protocol                   June 2018


          description
           "This flag is used to request that the uplink/downlink
          flows for which the network is providing
               Guaranteed-Bit-Rate service be excluded from the
               target IP flows for which
               Per-Session-Agg-Max-UL/DL-Bit-Rate is measured.";
        }
       description "Per-Session-Agg-Max-Bit-Rate Value";
      }

      grouping Allocation-Retention-Priority-Value {
        leaf priority-level {
          type uint8 {
            range "0..15";
          }
          mandatory true;
          description
          "This is a 4-bit unsigned integer value. It is used to decide
           whether a mobility session establishment or modification
           request can be accepted; this is typically used for
           admission control of Guaranteed Bit Rate traffic in case of
           resource limitations.";
        }
        leaf preemption-capability {
          type enumeration {
           enum enabled {
             value 0;
             description "enabled";
           }
           enum disabled {
             value 1;
             description "disabled";
           }
           enum reserved1 {
             value 2;
             description "reserved1";
           }
           enum reserved2 {
             value 3;
             description "reserved2";
           }
          }
          mandatory true;
          description
          "This is a 2-bit unsigned integer value.  It defines whether a
           service data flow can get resources tha were already
           assigned to another service data flow with a lower priority
           level.";



Matsushima, et al.      Expires December 20, 2018             [Page 113]


Internet-Draft              DMM FPC Protocol                   June 2018


        }
        leaf preemption-vulnerability {
          type enumeration {
           enum enabled {
             value 0;
             description "enabled";
           }
           enum disabled {
             value 1;
             description "disabled";
           }
           enum reserved1 {
             value 2;
             description "reserved1";
           }
           enum reserved2 {
             value 3;
             description "reserved2";
           }
          }
          mandatory true;
          description
          "This is a 2-bit unsigned integer value.  It defines whether a
            service data flow can lose the resources assigned to it in
            order to admit a service data flow with a higher priority
            level.";
        }
       description "Allocation-Retention-Priority Value";
      }

      typedef Aggregate-Max-DL-Bit-Rate-Value {
         type uint32;
         description
           "The aggregate maximum downlink bit rate that is
            requested/allocated for downlink IP flows.  The measurement
            units are bits per second.";
      }

       typedef Aggregate-Max-UL-Bit-Rate-Value {
         type uint32;
         description
           "The aggregate maximum downlink bit rate that is
            requested/allocated for downlink IP flows.  The measurement
            units are bits per second.";
       }

       typedef Guaranteed-DL-Bit-Rate-Value {
         type uint32;



Matsushima, et al.      Expires December 20, 2018             [Page 114]


Internet-Draft              DMM FPC Protocol                   June 2018


         description
         "The guaranteed bandwidth in bits per second for downlink
           IP flows.  The measurement units are bits per second.";
       }

       typedef Guaranteed-UL-Bit-Rate-Value {
         type uint32;
         description
           "The guaranteed bandwidth in bits per second for uplink
            IP flows.  The measurement units are bits per second.";
       }

       grouping QoS-Vendor-Specific-Attribute-Value-Base {
         leaf vendorid {
           type uint32;
           mandatory true;
           description
            "The Vendor ID is the SMI (Structure of Management
             Information) Network Management Private Enterprise Code of
             the IANA-maintained 'Private Enterprise Numbers'
             registry.";
           reference
             "'PRIVATE ENTERPRISE NUMBERS', SMI Network Management
               Private Enterprise Codes, April 2014,
                <http://www.iana.org/assignments/enterprise-numbers>";
         }
         leaf subtype {
           type uint8;
           mandatory true;
           description
             "An 8-bit field indicating the type of vendor-specific
              information carried in the option.  The namespace for this
              sub-type is managed by the vendor identified by the
              Vendor ID field.";
         }
         description
           "QoS Vendor-Specific Attribute.";
       }

       //Primary Structures (groupings)
       grouping qosattribute {
           leaf per-mn-agg-max-dl {
               type qos-pmip:Per-MN-Agg-Max-DL-Bit-Rate-Value;
               description "Per-MN-Agg-Max-DL-Bit-Rate Value";
           }
           leaf per-mn-agg-max-ul {
               type qos-pmip:Per-MN-Agg-Max-UL-Bit-Rate-Value;
               description "Per-MN-Agg-Max-UL-Bit-Rate Value";



Matsushima, et al.      Expires December 20, 2018             [Page 115]


Internet-Draft              DMM FPC Protocol                   June 2018


           }
           container per-session-agg-max-dl {
               uses qos-pmip:Per-Session-Agg-Max-Bit-Rate-Value;
               description "Per-Session-Agg-Max-Bit-Rate Value";
           }
           container per-session-agg-max-ul {
               uses qos-pmip:Per-Session-Agg-Max-Bit-Rate-Value;
               description "Per-Session-Agg-Max-Bit-Rate Value";
           }
           uses qos-pmip:Allocation-Retention-Priority-Value;
           leaf agg-max-dl {
               type qos-pmip:Aggregate-Max-DL-Bit-Rate-Value;
               description "Aggregate-Max-DL-Bit-Rate Value";
           }
           leaf agg-max-ul {
               type qos-pmip:Aggregate-Max-UL-Bit-Rate-Value;
               description "Aggregate-Max-UL-Bit-Rate Value";
           }
           leaf gbr-dl {
               type qos-pmip:Guaranteed-DL-Bit-Rate-Value;
               description "Guaranteed-DL-Bit-Rate Value";
           }
           leaf gbr-ul {
               type qos-pmip:Guaranteed-UL-Bit-Rate-Value;
               description "Guaranteed-UL-Bit-Rate Value";
           }
           description "PMIP QoS Attributes. Note Vendor option
           is not a part of this grouping";
       }

       grouping qosoption {
           leaf srid {
               type sr-id;
               mandatory true;
               description "Service Request Identifier";
           }
           leaf trafficclass {
               type traffic-class;
               mandatory true;
               description "Traffic Class";
           }
           leaf operationcode {
               type operational-code;
               mandatory true;
               description "Operation Code";
           }
           uses qos-pmip:qosattribute;
           uses qos-pmip:QoS-Vendor-Specific-Attribute-Value-Base;



Matsushima, et al.      Expires December 20, 2018             [Page 116]


Internet-Draft              DMM FPC Protocol                   June 2018


           container traffic-selector {
               uses traffic-selectors:traffic-selector;
               description "traffic selector";
           }
           description "PMIP QoS Option";
       }
   }
   <CODE ENDS>

A.4.  Traffic Selectors YANG Model

   This module defines traffic selector types commonly used in Proxy
   Mobile IP (PMIP).

   This module references [RFC6991].

   <CODE BEGINS> file "ietf-trafficselector-types@2018-05-17.yang"
   module ietf-trafficselector-types {
    yang-version 1.1;

    namespace
    "urn:ietf:params:xml:ns:yang:ietf-trafficselector-types";

    prefix "traffic-selectors";

    import ietf-inet-types {
      prefix inet;
      revision-date 2013-07-15;
    }

    organization "IETF Distributed Mobility Management (DMM)
    Working Group";

    contact
    "WG Web: <http://tools.ietf.org/wg/netmod/>
    WG List: <mailto:netmod@ietf.org>

    WG Chair: Dapeng Liu
    <mailto:maxpassion@gmail.com>

    WG Chair: Sri Gundavelli
    <mailto:sgundave@cisco.com>

    Editor: Satoru Matsushima
    <mailto:satoru.matsushima@g.softbank.co.jp>

    Editor: Lyle Bertz
    <mailto:lylebe551144@gmail.com>";



Matsushima, et al.      Expires December 20, 2018             [Page 117]


Internet-Draft              DMM FPC Protocol                   June 2018


    description
    "This module contains a collection of YANG definitions for
    traffic selectors for flow bindings.

    Copyright (c) 2016 IETF Trust and the persons identified as the
    document authors. All rights reserved.

    This document is subject to BCP 78 and the IETF Trust's Legal
    Provisions Relating to IETF Documents
    (http://trustee.ietf.org/license-info) in effect on the date of
    publication of this document. Please review these documents
    carefully, as they describe your rights and restrictions with
    respect to this document. Code Components extracted from this
    document must include Simplified BSD License text as described
    in Section 4.e of the Trust Legal Provisions and are provided
    without warranty as described in the Simplified BSD License.";

     revision 2018-05-17 {
       description
        "Initial Revision.";
       reference
        "RFC 6088: Traffic Selectors for Flow Bindings";
     }

    // Identities
      identity traffic-selector-format {
        description
        "The base type for Traffic-Selector Formats";
      }

      identity ipv4-binary-selector-format {
        base traffic-selector-format;
        description
          "IPv4 Binary Traffic Selector Format";
      }

      identity ipv6-binary-selector-format {
        base traffic-selector-format;
        description
          "IPv6 Binary Traffic Selector Format";
      }

      // Type definitions and groupings
      typedef ipsec-spi {
        type uint32;
        description
         "The first 32-bit IPsec Security Parameter Index (SPI)
         value on data. This field is defined in [RFC4303].";



Matsushima, et al.      Expires December 20, 2018             [Page 118]


Internet-Draft              DMM FPC Protocol                   June 2018


          reference
          "RFC 4303: IP Encapsulating Security
          Payload (ESP)";
      }

      grouping traffic-selector-base {
        description "A grouping of the commen leaves between the
          v4 and v6 Traffic Selectors";
        container ipsec-spi-range {
          presence "Enables setting ipsec spi range";
          description
          "Inclusive range representing IPSec Security Parameter
          Indices to be used. When only start-spi is present, it
          represents a single spi.";
      leaf start-spi {
          type ipsec-spi;
          mandatory true;
          description
            "The first 32-bit IPsec SPI value on data.";
          }
      leaf end-spi {
            type ipsec-spi;
            must ". >= ../start-spi" {
              error-message
                "The end-spi must be greater than or equal
                 to start-spi";
          }
         description
           "If more than one contiguous SPI value needs to be matched,
           then this field indicates the end value of a range.";
          }
       }
       container source-port-range {
         presence "Enables setting source port range";
         description
          "Inclusive range representing source ports to be used.
           When only start-port is present, it represents a single
        port. These value(s) are from the range of port numbers
           defined by IANA (http://www.iana.org).";
         leaf start-port {
            type inet:port-number;
            mandatory true;
            description
            "The first 16-bit source port number to be matched";
         }
         leaf end-port {
            type inet:port-number;
            must ". >= ../start-port" {



Matsushima, et al.      Expires December 20, 2018             [Page 119]


Internet-Draft              DMM FPC Protocol                   June 2018


            error-message
             "The end-port must be greater than or equal to start-port";
           }
           description
            "The last 16-bit source port number to be matched";
          }
       }
       container destination-port-range {
         presence "Enables setting destination port range";
         description
          "Inclusive range representing destination ports to be used.
          When only start-port is present, it represents a single
          port.";
           leaf start-port {
             type inet:port-number;
             mandatory true;
             description
             "The first 16-bit destination port number to be matched";
          }
          leaf end-port {
            type inet:port-number;
            must ". >= ../start-port" {
            error-message
              "The end-port must be greater than or equal to
             start-port";
           }
           description
        "The last 16-bit destination port number to be matched";
        }
      }
    }

    grouping ipv4-binary-traffic-selector {
      container source-address-range-v4 {
         presence "Enables setting source IPv4 address range";
         description
          "Inclusive range representing IPv4 addresses to be used. When
          only start-address is present, it represents a single
          address.";
         leaf start-address {
           type inet:ipv4-address;
           mandatory true;
          description
           "The first source address to be matched";
         }
         leaf end-address {
           type inet:ipv4-address;
           description



Matsushima, et al.      Expires December 20, 2018             [Page 120]


Internet-Draft              DMM FPC Protocol                   June 2018


            "The last source address to be matched";
          }
      }
      container destination-address-range-v4 {
         presence "Enables setting destination IPv4 address range";
         description
           "Inclusive range representing IPv4 addresses to be used.
           When only start-address is present, it represents a
           single address.";
         leaf start-address {
           type inet:ipv4-address;
           mandatory true;
           description
            "The first destination address to be matched";
         }
         leaf end-address {
           type inet:ipv4-address;
           description
            "The last destination address to be matched";
         }
      }
      container ds-range {
         presence "Enables setting dscp range";
         description
          "Inclusive range representing DiffServ Codepoints to be used.
          When only start-ds is present, it represents a single
          Codepoint.";
         leaf start-ds {
           type inet:dscp;
           mandatory true;
           description
            "The first differential service value to be matched";
       }
       leaf end-ds {
         type inet:dscp;
         must ". >= ../start-ds" {
           error-message
             "The end-ds must be greater than or equal to start-ds";
         }
         description
           "The last differential service value to be matched";
      }
     }
     container protocol-range {
       presence "Enables setting protocol range";
       description
         "Inclusive range representing IP protocol(s) to be used. When
          only start-protocol is present, it represents a single



Matsushima, et al.      Expires December 20, 2018             [Page 121]


Internet-Draft              DMM FPC Protocol                   June 2018


          protocol.";
       leaf start-protocol {
         type uint8;
         mandatory true;
         description
           "The first 8-bit protocol value to be matched.";
        }
        leaf end-protocol {
          type uint8;
          must ". >= ../start-protocol" {
            error-message
              "The end-protocol must be greater than or equal to
             start-protocol";
          }
        description
          "The last 8-bit protocol value to be matched.";
        }
      }
      description "ipv4 binary traffic selector";
    }
     grouping ipv6-binary-traffic-selector {
      container source-address-range-v6 {
        presence "Enables setting source IPv6 address range";
         description
          "Inclusive range representing IPv6 addresses to be used.
          When only start-address is present, it represents a
          single address.";
         leaf start-address {
           type inet:ipv6-address;
           mandatory true;
           description
           "The first source address, from the
           range of 128-bit IPv6 addresses to be matched";
         }
         leaf end-address {
           type inet:ipv6-address;
           description
               "The last source address, from the
               range of 128-bit IPv6 addresses to be matched";
         }
      }
      container destination-address-range-v6 {
        presence "Enables setting destination IPv6 address range";
        description
          "Inclusive range representing IPv6 addresses to be used.
           When only start-address is present, it represents a
           single address.";
        leaf start-address {



Matsushima, et al.      Expires December 20, 2018             [Page 122]


Internet-Draft              DMM FPC Protocol                   June 2018


          type inet:ipv6-address;
          mandatory true;
          description
              "The first destination address, from the
              range of 128-bit IPv6 addresses to be matched";
        }
        leaf end-address {
          type inet:ipv6-address;
          description
              "The last destination address, from the
              range of 128-bit IPv6 addresses to be matched";
       }
     }
     container flow-label-range {
       presence "Enables setting Flow Label range";
       description
         "Inclusive range representing IPv4 addresses to be used. When
          only start-flow-label is present, it represents a single
          flow label.";
       leaf start-flow-label {
         type inet:ipv6-flow-label;
         description
           "The first flow label value to be matched";
       }
       leaf end-flow-label {
         type inet:ipv6-flow-label;
         must ". >= ../start-flow-label" {
           error-message
             "The end-flow-lable must be greater than or equal to
              start-flow-label";
         }
         description
            "The first flow label value to be matched";
       }
      }
     container traffic-class-range {
       presence "Enables setting the traffic class range";
       description
        "Inclusive range representing IPv4 addresses to be used. When
         only start-traffic-class is present, it represents a single
         traffic class.";
       leaf start-traffic-class {
         type inet:dscp;
         description
          "The first traffic class value to be matched";
         reference
          "RFC 3260: New Terminology and Clarifications for Diffserv
           RFC 3168: The Addition of Explicit Congestion Notification



Matsushima, et al.      Expires December 20, 2018             [Page 123]


Internet-Draft              DMM FPC Protocol                   June 2018


           (ECN) to IP";
       }
       leaf end-traffic-class {
         type inet:dscp;
         must ". >= ../start-traffic-class" {
           error-message
             "The end-traffic-class must be greater than or equal to
              start-traffic-class";
         }
         description
           "The last traffic class value to be matched";
       }
     }
     container next-header-range {
       presence "Enables setting Next Header range";
       description
        "Inclusive range representing Next Headers to be used. When
         only start-next-header is present, it represents a
         single Next Header.";
       leaf start-next-header {
         type uint8;
         description
          "The first 8-bit next header value to be matched.";
       }
       leaf end-next-header {
         type uint8;
         must ". >= ../start-next-header" {
           error-message
             "The end-next-header must be greater than or equal to
             start-next-header";
         }
         description
           "The last 8-bit next header value to be matched.";
       }
     }
     description "ipv6 binary traffic selector";
   }

     grouping traffic-selector {
       leaf ts-format {
          type identityref {
            base traffic-selector-format;
          }
          description "Traffic Selector Format";
       }
       uses traffic-selectors:traffic-selector-base;
       uses traffic-selectors:ipv4-binary-traffic-selector;
       uses traffic-selectors:ipv6-binary-traffic-selector;



Matsushima, et al.      Expires December 20, 2018             [Page 124]


Internet-Draft              DMM FPC Protocol                   June 2018


       description
        "The traffic selector includes the parameters used to match
          packets for a specific flow binding.";
       reference
        "RFC 6089: Flow Bindings in Mobile IPv6 and Network
          Mobility (NEMO) Basic Support";
     }
   }
   <CODE ENDS>

A.5.  RFC 5777 Classifier YANG Model

   This module defines the RFC 5777 Classifer.

   This module references [RFC5777].

   <CODE BEGINS> file "ietf-diam-trafficclassifier@2018-05-17.yang"
   module ietf-diam-trafficclassifier {
    yang-version 1.1;

    namespace
    "urn:ietf:params:xml:ns:yang:ietf-diam-trafficclassifier";

    prefix "diamclassifier";

    import ietf-inet-types {
      prefix inet;
      revision-date 2013-07-15;
    }
    import ietf-yang-types { prefix yang-types; }

    organization "IETF Distributed Mobility Management (DMM)
    Working Group";

    contact
    "WG Web: <http://tools.ietf.org/wg/netmod/>
    WG List: <mailto:netmod@ietf.org>

    WG Chair: Dapeng Liu
    <mailto:maxpassion@gmail.com>

    WG Chair: Sri Gundavelli
    <mailto:sgundave@cisco.com>

    Editor: Satoru Matsushima
    <mailto:satoru.matsushima@g.softbank.co.jp>

    Editor: Lyle Bertz



Matsushima, et al.      Expires December 20, 2018             [Page 125]


Internet-Draft              DMM FPC Protocol                   June 2018


    <mailto:lylebe551144@gmail.com>";

    description
    "This module contains a collection of YANG definitions for
    traffic classification and QoS Attributes for Diameter.

    Copyright (c) 2018 IETF Trust and the persons identified as the
    document authors. All rights reserved.

    This document is subject to BCP 78 and the IETF Trust's Legal
    Provisions Relating to IETF Documents
    (http://trustee.ietf.org/license-info) in effect on the date of
    publication of this document. Please review these documents
    carefully, as they describe your rights and restrictions with
    respect to this document. Code Components extracted from this
    document must include Simplified BSD License text as described
    in Section 4.e of the Trust Legal Provisions and are provided
    without warranty as described in the Simplified BSD License.";

     revision 2018-05-17 {
       description
           "Initial";
       reference
       "RFC 5777: Traffic Classification and Quality of Service (QoS)
           Attributes for Diameter";
     }

       typedef eui64-address-type {
           type string {
               length "6";
           }
           description
               "specifies a single layer 2 address in EUI-64 format.
                The value is an 8-octet encoding of the address as
                it would appear in the frame header.";
       }
       typedef direction-type {
           type enumeration {
               enum IN {
                   value 0;
                   description
                       "Applies to flows from the managed terminal.";
               }
               enum OUT {
                   value 1;
                   description
                    "Applies to flows to the managed terminal.";
               }



Matsushima, et al.      Expires December 20, 2018             [Page 126]


Internet-Draft              DMM FPC Protocol                   June 2018


               enum BOTH {
                   value 2;
                   description
                       "Applies to flows both to and from the managed
                           terminal.";
               }
           }
           description
               "Specifies in which direction to apply the classifier.";
       }
       typedef negated-flag-type {
           type enumeration {
               enum False { value 0;
                   description "false"; }
               enum True { value 1;
                   description "True"; }
           }
           description
               "When set to True, the meaning of the match is
                inverted and the classifier will match addresses
                other than those specified by the From-Spec or
                To-Spec AVP.

                Note that the negation does not impact the port
                   comparisons.";
       }
       grouping index {
           leaf index {
               type uint16;
               mandatory true;
               description "Identifier used for referencing";
           }
           description "Index Value";
       }
       grouping to-from-spec-value {
           leaf-list ip-address {
               type inet:ip-address;
               description "IP address";
           }
           list ip-address-range {
               key index;
               uses diamclassifier:index;
               leaf ip-address-start {
                   type inet:ip-address;
                   description "IP Address Start";
               }
               leaf ip-address-end {
                   type inet:ip-address;



Matsushima, et al.      Expires December 20, 2018             [Page 127]


Internet-Draft              DMM FPC Protocol                   June 2018


                   description "IP Address End";
               }
               description "IP Address Range";
           }
           leaf-list ip-address-mask {
               type inet:ip-prefix;
               description "IP Address Mask";
           }
           leaf-list mac-address {
               type yang-types:mac-address;
               description "MAC address";
           }
           list mac-address-mask {
               key mac-address;
               leaf mac-address {
                   type yang-types:mac-address;
                   mandatory true;
                   description "MAC address";
               }
               leaf macaddress-mask-pattern {
                   type yang-types:mac-address;
                   mandatory true;
                   description
                    "The value specifies the bit positions of a
                     MAC address that are taken for matching.";
               }
               description "MAC Address Mask";
           }
           leaf-list eui64-address {
               type diamclassifier:eui64-address-type;
               description "EUI64 Address";
           }
           list eui64-address-mask {
               key eui64-address;
               leaf eui64-address {
                   type diamclassifier:eui64-address-type;
                   mandatory true;
                   description "eui64 address";
               }
               leaf eui64-address-mask-pattern {
                   type diamclassifier:eui64-address-type;
                   mandatory true;
                   description
                    "The value is 8 octets specifying the bit
                     positions of a EUI64 address that are taken
                    for matching.";
               }
               description "EUI64 Address Mask";



Matsushima, et al.      Expires December 20, 2018             [Page 128]


Internet-Draft              DMM FPC Protocol                   June 2018


           }
           leaf-list port {
               type inet:port-number;
               description "Port Number";
           }
           list port-range {
               key index;
               uses diamclassifier:index;
               leaf ip-address-start {
                   type inet:port-number;
                   description "Port Start";
               }
               leaf ip-address-end {
                   type inet:port-number;
                   description "Port End";
               }
               description "Port Range";
           }
           leaf negated {
               type diamclassifier:negated-flag-type;
               description "Negated";
           }
           leaf use-assigned-address {
               type boolean;
               description "Use Assigned Address";
           }
           description
               "Basic traffic description value";
       }

       grouping option-type-group {
           leaf option-type {
               type uint8;
               mandatory true;
               description "Option Type";
           }
           leaf-list ip-option-value {
               type string;
               description "Option Value";
           }
           leaf negated {
               type diamclassifier:negated-flag-type;
               description "Negated";
           }
           description "Common X Option Pattern";
       }
       typedef vlan-id {
           type uint32 {



Matsushima, et al.      Expires December 20, 2018             [Page 129]


Internet-Draft              DMM FPC Protocol                   June 2018


               range "0..4095";
           }
           description "VLAN ID";
       }

     grouping classifier {
       leaf protocol {
           type uint8;
           description "Protocol";
       }
       leaf direction {
           type diamclassifier:direction-type;
           description "Direction";
       }
       list from-spec {
           key index;
           uses diamclassifier:index;
           uses diamclassifier:to-from-spec-value;
           description "from specification";
       }
       list to-spec {
           key index;
           uses diamclassifier:index;
           uses diamclassifier:to-from-spec-value;
           description "to specification";
       }
       leaf-list disffserv-code-point {
           type inet:dscp;
           description "DSCP";
       }
       leaf fragmentation-flag {
       type enumeration {
               enum DF {
                   value 0;
                   description "Don't Fragment";
               }
               enum MF {
                   value 1;
                   description "More Fragments";
               }
           }
           description "Fragmenttation Flag";
       }
       list ip-option {
           key option-type;
           uses diamclassifier:option-type-group;
           description "IP Option Value";
       }



Matsushima, et al.      Expires December 20, 2018             [Page 130]


Internet-Draft              DMM FPC Protocol                   June 2018


       list tcp-option {
           key option-type;
           uses diamclassifier:option-type-group;
           description "TCP Option Value";
       }
       list tcp-flag {
           key tcp-flag-type;
           leaf tcp-flag-type {
               type uint32;
               mandatory true;
               description "TCP Flag Type";
           }
           leaf negated {
               type diamclassifier:negated-flag-type;
               description "Negated";
           }
           description "TCP Flags";
       }
       list icmp-option {
           key option-type;
           uses diamclassifier:option-type-group;
           description "ICMP Option Value";
       }
       list eth-option {
           key index;
           uses diamclassifier:index;
           container eth-proto-type {
               leaf-list eth-ether-type {
                   type string {
                       length "2";
                   }
                   description "value of ethertype field";
               }
               leaf-list eth-sap {
                   type string {
                       length "2";
                   }
                   description "802.2 SAP";
               }
               description "Ether Proto Type";
           }
           list vlan-id-range {
               key index;
               uses diamclassifier:index;
               leaf-list s-vlan-id-start {
                   type diamclassifier:vlan-id;
                   description "S-VID  VLAN ID Start";
               }



Matsushima, et al.      Expires December 20, 2018             [Page 131]


Internet-Draft              DMM FPC Protocol                   June 2018


               leaf-list s-vlan-id-end {
                   type diamclassifier:vlan-id;
                   description "S-VID VLAN ID End";
               }
               leaf-list c-vlan-id-start {
                   type diamclassifier:vlan-id;
                   description "C-VID  VLAN ID Start";
               }
               leaf-list c-vlan-id-end {
                   type diamclassifier:vlan-id;
                   description "C-VID  VLAN ID End";
               }
               description "VLAN ID Range";
           }
           list user-priority-range {
               key index;
               uses diamclassifier:index;
               leaf-list low-user-priority {
                   type uint32 {
                       range "0..7";
                   }
                   description "Low User Priority";
               }
               leaf-list high-user-priority {
                   type uint32 {
                       range "0..7";
                   }
                   description "High User Priority";
               }
               description "User priority range";
           }
           description "Ether Option";
       }
       description "RFC 5777 Classifier";
     }
   }
   <CODE ENDS>

Appendix B.  FPC YANG Tree Structure

   This section only shows the structure for FPC YANG model.  NOTE, it
   does NOT show the settings, Action values or Descriptor Value.

   descriptor_value:
   +--rw (descriptor-value)
     +--:(all-traffic)
     |  +--rw all-traffic?                    empty
     +--:(no-traffic)



Matsushima, et al.      Expires December 20, 2018             [Page 132]


Internet-Draft              DMM FPC Protocol                   June 2018


     |  +--rw no-traffic?                     empty
     +--:(prefix-descriptor)
     |  +--rw destination-ip?                 inet:ip-prefix
     |  +--rw source-ip?                      inet:ip-prefix
     +--:(pmip-selector)
     |  +--rw ts-format?                      identityref
     |  +--rw ipsec-spi-range!
     |  |  +--rw start-spi    ipsec-spi
     |  |  +--rw end-spi?     ipsec-spi
     |  +--rw source-port-range!
     |  |  +--rw start-port    inet:port-number
     |  |  +--rw end-port?     inet:port-number
     |  +--rw destination-port-range!
     |  |  +--rw start-port    inet:port-number
     |  |  +--rw end-port?     inet:port-number
     |  +--rw source-address-range-v4!
     |  |  +--rw start-address    inet:ipv4-address
     |  |  +--rw end-address?     inet:ipv4-address
     |  +--rw destination-address-range-v4!
     |  |  +--rw start-address    inet:ipv4-address
     |  |  +--rw end-address?     inet:ipv4-address
     |  +--rw ds-range!
     |  |  +--rw start-ds    inet:dscp
     |  |  +--rw end-ds?     inet:dscp
     |  +--rw protocol-range!
     |  |  +--rw start-protocol    uint8
     |  |  +--rw end-protocol?     uint8
     |  +--rw source-address-range-v6!
     |  |  +--rw start-address    inet:ipv6-address
     |  |  +--rw end-address?     inet:ipv6-address
     |  +--rw destination-address-range-v6!
     |  |  +--rw start-address    inet:ipv6-address
     |  |  +--rw end-address?     inet:ipv6-address
     |  +--rw flow-label-range!
     |  |  +--rw start-flow-label?   inet:ipv6-flow-label
     |  |  +--rw end-flow-label?     inet:ipv6-flow-label
     |  +--rw traffic-class-range!
     |  |  +--rw start-traffic-class?   inet:dscp
     |  |  +--rw end-traffic-class?     inet:dscp
     |  +--rw next-header-range!
     |     +--rw start-next-header?   uint8
     |     +--rw end-next-header?     uint8
     +--:(rfc5777-classifier-template)
     |  +--rw rfc5777-classifier-template
     |     +--rw protocol?               uint8
     |     +--rw direction?              diamclassifier:direction-type
     |     +--rw from-spec* [index]
     |     |  +--rw index                   uint16



Matsushima, et al.      Expires December 20, 2018             [Page 133]


Internet-Draft              DMM FPC Protocol                   June 2018


     |     |  +--rw ip-address*             inet:ip-address
     |     |  +--rw ip-address-range* [index]
     |     |  |  +--rw index               uint16
     |     |  |  +--rw ip-address-start?   inet:ip-address
     |     |  |  +--rw ip-address-end?     inet:ip-address
     |     |  +--rw ip-address-mask*        inet:ip-prefix
     |     |  +--rw mac-address*            yang-types:mac-address
     |     |  +--rw mac-address-mask* [mac-address]
     |     |  |  +--rw mac-address              yang-types:mac-address
     |     |  |  +--rw macaddress-mask-pattern  yang-types:mac-address
     |     |  +--rw eui64-address*
                         diamclassifier:eui64-address-type
     |     |  +--rw eui64-address-mask* [eui64-address]
     |     |  |  +--rw eui64-address
                         diamclassifier:eui64-address-type
     |     |  |  +--rw eui64-address-mask-pattern
                         diamclassifier:eui64-address-type
     |     |  +--rw port*                   inet:port-number
     |     |  +--rw port-range* [index]
     |     |  |  +--rw index               uint16
     |     |  |  +--rw ip-address-start?   inet:port-number
     |     |  |  +--rw ip-address-end?     inet:port-number
     |     |  +--rw negated?
                         diamclassifier:negated-flag-type
     |     |  +--rw use-assigned-address?   boolean
     |     +--rw to-spec* [index]
     |     |  +--rw index                   uint16
     |     |  +--rw ip-address*             inet:ip-address
     |     |  +--rw ip-address-range* [index]
     |     |  |  +--rw index               uint16
     |     |  |  +--rw ip-address-start?   inet:ip-address
     |     |  |  +--rw ip-address-end?     inet:ip-address
     |     |  +--rw ip-address-mask*        inet:ip-prefix
     |     |  +--rw mac-address*            yang-types:mac-address
     |     |  +--rw mac-address-mask* [mac-address]
     |     |  |  +--rw mac-address                yang-types:mac-address
     |     |  |  +--rw macaddress-mask-pattern    yang-types:mac-address
     |     |  +--rw eui64-address*
                         diamclassifier:eui64-address-type
     |     |  +--rw eui64-address-mask* [eui64-address]
     |     |  |  +--rw eui64-address
                         diamclassifier:eui64-address-type
     |     |  |  +--rw eui64-address-mask-pattern
                         diamclassifier:eui64-address-type
     |     |  +--rw port*                   inet:port-number
     |     |  +--rw port-range* [index]
     |     |  |  +--rw index               uint16
     |     |  |  +--rw ip-address-start?   inet:port-number



Matsushima, et al.      Expires December 20, 2018             [Page 134]


Internet-Draft              DMM FPC Protocol                   June 2018


     |     |  |  +--rw ip-address-end?     inet:port-number
     |     |  +--rw negated?
                         diamclassifier:negated-flag-type
     |     |  +--rw use-assigned-address?   boolean
     |     +--rw disffserv-code-point*   inet:dscp
     |     +--rw fragmentation-flag?     enumeration
     |     +--rw ip-option* [option-type]
     |     |  +--rw option-type        uint8
     |     |  +--rw ip-option-value*   string
     |     |  +--rw negated?           diamclassifier:negated-flag-type
     |     +--rw tcp-option* [option-type]
     |     |  +--rw option-type        uint8
     |     |  +--rw ip-option-value*   string
     |     |  +--rw negated?           diamclassifier:negated-flag-type
     |     +--rw tcp-flag* [tcp-flag-type]
     |     |  +--rw tcp-flag-type    uint32
     |     |  +--rw negated?         diamclassifier:negated-flag-type
     |     +--rw icmp-option* [option-type]
     |     |  +--rw option-type        uint8
     |     |  +--rw ip-option-value*   string
     |     |  +--rw negated?           diamclassifier:negated-flag-type
     |     +--rw eth-option* [index]
     |        +--rw index                  uint16
     |        +--rw eth-proto-type
     |        |  +--rw eth-ether-type*   string
     |        |  +--rw eth-sap*          string
     |        +--rw vlan-id-range* [index]
     |        |  +--rw index              uint16
     |        |  +--rw s-vlan-id-start*   diamclassifier:vlan-id
     |        |  +--rw s-vlan-id-end*     diamclassifier:vlan-id
     |        |  +--rw c-vlan-id-start*   diamclassifier:vlan-id
     |        |  +--rw c-vlan-id-end*     diamclassifier:vlan-id
     |        +--rw user-priority-range* [index]
     |           +--rw index                 uint16
     |           +--rw low-user-priority*    uint32
     |           +--rw high-user-priority*   uint32
     +--:(packet-filter)
     |  +--rw packet-filter
     |     +--rw direction?             fpcbase:packet-filter-direction
     |     +--rw identifier?              uint8
     |     +--rw evaluation-precedence?   uint8
     |     +--rw contents* [component-type-identifier]
     |        +--rw component-type-identifier fpcbase:component-type-id
     |        +--rw (value)?
     |           +--:(ipv4-local)
     |           |  +--rw ipv4-local?                  inet:ipv4-address
     |           +--:(ipv6-prefix-local)
     |           |  +--rw ipv6-prefix-local?           inet:ipv6-prefix



Matsushima, et al.      Expires December 20, 2018             [Page 135]


Internet-Draft              DMM FPC Protocol                   June 2018


     |           +--:(ipv4-ipv6-remote)
     |           |  +--rw ipv4-ipv6-remote?            inet:ip-address
     |           +--:(ipv6-prefix-remote)
     |           |  +--rw ipv6-prefix-remote?          inet:ipv6-prefix
     |           +--:(next-header)
     |           |  +--rw next-header?                 uint8
     |           +--:(local-port)
     |           |  +--rw local-port?                  inet:port-number
     |           +--:(local-port-range)
     |           |  +--rw local-port-lo?               inet:port-number
     |           |  +--rw local-port-hi?               inet:port-number
     |           +--:(remote-port)
     |           |  +--rw remote-port?                 inet:port-number
     |           +--:(remote-port-range)
     |           |  +--rw remote-port-lo?              inet:port-number
     |           |  +--rw remote-port-hi?              inet:port-number
     |           +--:(ipsec-index)
     |           |  +--rw ipsec-index?     traffic-selectors:ipsec-spi
     |           +--:(traffic-class)
     |           |  +--rw traffic-class?               inet:dscp
     |           +--:(traffic-class-range)
     |           |  +--rw traffic-class-lo?            inet:dscp
     |           |  +--rw traffic-class-hi?            inet:dscp
     |           +--:(flow-label)
     |              +--rw flow-label*    inet:ipv6-flow-label
     +--:(tunnel-info)
        +--rw tunnel-info
           +--rw tunnel-local-address?    inet:ip-address
           +--rw tunnel-remote-address?   inet:ip-address
           +--rw mtu-size?                uint32
           +--rw tunnel?                  identityref
           +--rw payload-type?            enumeration
           +--rw gre-key?                 uint32
           +--rw gtp-tunnel-info
           |  +--rw local-tunnel-identifier?    uint32
           |  +--rw remote-tunnel-identifier?   uint32
           |  +--rw sequence-numbers-enabled?   boolean
           +--rw ebi?                     fpcbase:ebi-type
           +--rw lbi?                     fpcbase:ebi-type

   action_value:
   +--:(action-value)
   |  +--rw (action-value)
   |     +--:(drop)
   |     |  +--rw drop?                           empty
   |     +--:(rewrite)
   |     |  +--rw rewrite
   |     |     +--rw (rewrite-value)?



Matsushima, et al.      Expires December 20, 2018             [Page 136]


Internet-Draft              DMM FPC Protocol                   June 2018


   |     |        +--:(prefix-descriptor)
   |     |        |  +--rw destination-ip?               inet:ip-prefix
   |     |        |  +--rw source-ip?                    inet:ip-prefix
   |     |        +--:(pmip-selector)
   |     |        |  +--rw ts-format?                      identityref
   |     |        |  +--rw ipsec-spi-range!
   |     |        |  |  +--rw start-spi    ipsec-spi
   |     |        |  |  +--rw end-spi?     ipsec-spi
   |     |        |  +--rw source-port-range!
   |     |        |  |  +--rw start-port    inet:port-number
   |     |        |  |  +--rw end-port?     inet:port-number
   |     |        |  +--rw destination-port-range!
   |     |        |  |  +--rw start-port    inet:port-number
   |     |        |  |  +--rw end-port?     inet:port-number
   |     |        |  +--rw source-address-range-v4!
   |     |        |  |  +--rw start-address    inet:ipv4-address
   |     |        |  |  +--rw end-address?     inet:ipv4-address
   |     |        |  +--rw destination-address-range-v4!
   |     |        |  |  +--rw start-address    inet:ipv4-address
   |     |        |  |  +--rw end-address?     inet:ipv4-address
   |     |        |  +--rw ds-range!
   |     |        |  |  +--rw start-ds    inet:dscp
   |     |        |  |  +--rw end-ds?     inet:dscp
   |     |        |  +--rw protocol-range!
   |     |        |  |  +--rw start-protocol    uint8
   |     |        |  |  +--rw end-protocol?     uint8
   |     |        |  +--rw source-address-range-v6!
   |     |        |  |  +--rw start-address    inet:ipv6-address
   |     |        |  |  +--rw end-address?     inet:ipv6-address
   |     |        |  +--rw destination-address-range-v6!
   |     |        |  |  +--rw start-address    inet:ipv6-address
   |     |        |  |  +--rw end-address?     inet:ipv6-address
   |     |        |  +--rw flow-label-range!
   |     |        |  |  +--rw start-flow-label?   inet:ipv6-flow-label
   |     |        |  |  +--rw end-flow-label?     inet:ipv6-flow-label
   |     |        |  +--rw traffic-class-range!
   |     |        |  |  +--rw start-traffic-class?   inet:dscp
   |     |        |  |  +--rw end-traffic-class?     inet:dscp
   |     |        |  +--rw next-header-range!
   |     |        |     +--rw start-next-header?   uint8
   |     |        |     +--rw end-next-header?     uint8
   |     |        +--:(rfc5777-classifier-template)
   |     |           +--rw rfc5777-classifier-template
   |     |              +--rw protocol?               uint8
   |     |              +--rw direction?
                         diamclassifier:direction-type
   |     |              +--rw from-spec* [index]
   |     |              |  +--rw index                   uint16



Matsushima, et al.      Expires December 20, 2018             [Page 137]


Internet-Draft              DMM FPC Protocol                   June 2018


   |     |              |  +--rw ip-address*             inet:ip-address
   |     |              |  +--rw ip-address-range* [index]
   |     |              |  |  +--rw index               uint16
   |     |              |  |  +--rw ip-address-start?   inet:ip-address
   |     |              |  |  +--rw ip-address-end?     inet:ip-address
   |     |              |  +--rw ip-address-mask*        inet:ip-prefix
   |     |              |  +--rw mac-address*    yang-types:mac-address
   |     |              |  +--rw mac-address-mask* [mac-address]
   |     |              |  |  +--rw mac-address
                                    yang-types:mac-address
   |     |              |  |  +--rw macaddress-mask-pattern
                                    yang-types:mac-address
   |     |              |  +--rw eui64-address*
                                    diamclassifier:eui64-address-type
   |     |              |  +--rw eui64-address-mask* [eui64-address]
   |     |              |  |  +--rw eui64-address
                                    diamclassifier:eui64-address-type
   |     |              |  |  +--rw eui64-address-mask-pattern
                                    diamclassifier:eui64-address-type
   |     |              |  +--rw port*                 inet:port-number
   |     |              |  +--rw port-range* [index]
   |     |              |  |  +--rw index               uint16
   |     |              |  |  +--rw ip-address-start?   inet:port-number
   |     |              |  |  +--rw ip-address-end?     inet:port-number
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              |  +--rw use-assigned-address?   boolean
   |     |              +--rw to-spec* [index]
   |     |              |  +--rw index                   uint16
   |     |              |  +--rw ip-address*             inet:ip-address
   |     |              |  +--rw ip-address-range* [index]
   |     |              |  |  +--rw index               uint16
   |     |              |  |  +--rw ip-address-start?   inet:ip-address
   |     |              |  |  +--rw ip-address-end?     inet:ip-address
   |     |              |  +--rw ip-address-mask*        inet:ip-prefix
   |     |              |  +--rw mac-address*
                                    yang-types:mac-address
   |     |              |  +--rw mac-address-mask* [mac-address]
   |     |              |  |  +--rw mac-address
                                    yang-types:mac-address
   |     |              |  |  +--rw macaddress-mask-pattern
                                    yang-types:mac-address
   |     |              |  +--rw eui64-address*
                                    diamclassifier:eui64-address-type
   |     |              |  +--rw eui64-address-mask* [eui64-address]
   |     |              |  |  +--rw eui64-address
                                    diamclassifier:eui64-address-type
   |     |              |  |  +--rw eui64-address-mask-pattern



Matsushima, et al.      Expires December 20, 2018             [Page 138]


Internet-Draft              DMM FPC Protocol                   June 2018


                                    diamclassifier:eui64-address-type
   |     |              |  +--rw port*                 inet:port-number
   |     |              |  +--rw port-range* [index]
   |     |              |  |  +--rw index               uint16
   |     |              |  |  +--rw ip-address-start?   inet:port-number
   |     |              |  |  +--rw ip-address-end?     inet:port-number
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              |  +--rw use-assigned-address?   boolean
   |     |              +--rw disffserv-code-point*   inet:dscp
   |     |              +--rw fragmentation-flag?     enumeration
   |     |              +--rw ip-option* [option-type]
   |     |              |  +--rw option-type        uint8
   |     |              |  +--rw ip-option-value*   string
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              +--rw tcp-option* [option-type]
   |     |              |  +--rw option-type        uint8
   |     |              |  +--rw ip-option-value*   string
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              +--rw tcp-flag* [tcp-flag-type]
   |     |              |  +--rw tcp-flag-type    uint32
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              +--rw icmp-option* [option-type]
   |     |              |  +--rw option-type        uint8
   |     |              |  +--rw ip-option-value*   string
   |     |              |  +--rw negated?
                                    diamclassifier:negated-flag-type
   |     |              +--rw eth-option* [index]
   |     |                 +--rw index                  uint16
   |     |                 +--rw eth-proto-type
   |     |                 |  +--rw eth-ether-type*   string
   |     |                 |  +--rw eth-sap*          string
   |     |                 +--rw vlan-id-range* [index]
   |     |                 |  +--rw index              uint16
   |     |                 |  +--rw s-vlan-id-start*
                                    diamclassifier:vlan-id
   |     |                 |  +--rw s-vlan-id-end*
                                    diamclassifier:vlan-id
   |     |                 |  +--rw c-vlan-id-start*
                                    diamclassifier:vlan-id
   |     |                 |  +--rw c-vlan-id-end*
                                    diamclassifier:vlan-id
   |     |                 +--rw user-priority-range* [index]
   |     |                    +--rw index                 uint16
   |     |                    +--rw low-user-priority*    uint32



Matsushima, et al.      Expires December 20, 2018             [Page 139]


Internet-Draft              DMM FPC Protocol                   June 2018


   |     |                    +--rw high-user-priority*   uint32
   |     +--:(copy-forward-nexthop)
   |     |  +--rw copy-forward-nexthop
   |     |     +--rw (next-hop-value)?
   |     |        +--:(ip-address)
   |     |        |  +--rw ip-address?           inet:ip-address
   |     |        +--:(mac-address)
   |     |        |  +--rw mac-address?          ytypes:mac-address
   |     |        +--:(service-path)
   |     |        |  +--rw service-path?   fpcbase:fpc-service-path-id
   |     |        +--:(mpls-path)
   |     |        |  +--rw mpls-path?            fpcbase:fpc-mpls-label
   |     |        +--:(nsh)
   |     |        |  +--rw nsh?                  string
   |     |        +--:(interface)
   |     |        |  +--rw interface?            uint16
   |     |        +--:(segment-identifier)
   |     |        |  +--rw segment-identifier?   fpcbase:segment-id
   |     |        +--:(mpls-label-stack)
   |     |        |  +--rw mpls-label-stack*     fpcbase:fpc-mpls-label
   |     |        +--:(mpls-sr-stack)
   |     |        |  +--rw mpls-sr-stack*        fpcbase:fpc-mpls-label
   |     |        +--:(srv6-stack)
   |     |        |  +--rw srv6-stack*           fpcbase:segment-id
   |     |        +--:(tunnel-info)
   |     |           +--rw tunnel-info
   |     |              +--rw tunnel-local-address?    inet:ip-address
   |     |              +--rw tunnel-remote-address?   inet:ip-address
   |     |              +--rw mtu-size?                uint32
   |     |              +--rw tunnel?                  identityref
   |     |              +--rw payload-type?            enumeration
   |     |              +--rw gre-key?                 uint32
   |     |              +--rw gtp-tunnel-info
   |     |              |  +--rw local-tunnel-identifier?    uint32
   |     |              |  +--rw remote-tunnel-identifier?   uint32
   |     |              |  +--rw sequence-numbers-enabled?   boolean
   |     |              +--rw ebi?                     fpcbase:ebi-type
   |     |              +--rw lbi?                     fpcbase:ebi-type
   |     +--:(nexthop)
   |     |  +--rw nexthop
   |     |     +--rw (next-hop-value)?
   |     |        +--:(ip-address)
   |     |        |  +--rw ip-address?           inet:ip-address
   |     |        +--:(mac-address)
   |     |        |  +--rw mac-address?          ytypes:mac-address
   |     |        +--:(service-path)
   |     |        |  +--rw service-path?   fpcbase:fpc-service-path-id
   |     |        +--:(mpls-path)



Matsushima, et al.      Expires December 20, 2018             [Page 140]


Internet-Draft              DMM FPC Protocol                   June 2018


   |     |        |  +--rw mpls-path?            fpcbase:fpc-mpls-label
   |     |        +--:(nsh)
   |     |        |  +--rw nsh?                  string
   |     |        +--:(interface)
   |     |        |  +--rw interface?            uint16
   |     |        +--:(segment-identifier)
   |     |        |  +--rw segment-identifier?   fpcbase:segment-id
   |     |        +--:(mpls-label-stack)
   |     |        |  +--rw mpls-label-stack*     fpcbase:fpc-mpls-label
   |     |        +--:(mpls-sr-stack)
   |     |        |  +--rw mpls-sr-stack*        fpcbase:fpc-mpls-label
   |     |        +--:(srv6-stack)
   |     |        |  +--rw srv6-stack*           fpcbase:segment-id
   |     |        +--:(tunnel-info)
   |     |           +--rw tunnel-info
   |     |              +--rw tunnel-local-address?    inet:ip-address
   |     |              +--rw tunnel-remote-address?   inet:ip-address
   |     |              +--rw mtu-size?                uint32
   |     |              +--rw tunnel?                  identityref
   |     |              +--rw payload-type?            enumeration
   |     |              +--rw gre-key?                 uint32
   |     |              +--rw gtp-tunnel-info
   |     |              |  +--rw local-tunnel-identifier?    uint32
   |     |              |  +--rw remote-tunnel-identifier?   uint32
   |     |              |  +--rw sequence-numbers-enabled?   boolean
   |     |              +--rw ebi?                     fpcbase:ebi-type
   |     |              +--rw lbi?                     fpcbase:ebi-type
   |     +--:(qos)
   |        +--rw trafficclass?                   inet:dscp
   |        +--rw per-mn-agg-max-dl?
                    qos-pmip:Per-MN-Agg-Max-DL-Bit-Rate-Value
   |        +--rw per-mn-agg-max-ul?
                    qos-pmip:Per-MN-Agg-Max-UL-Bit-Rate-Value
   |        +--rw per-session-agg-max-dl
   |        |  +--rw max-rate        uint32
   |        |  +--rw service-flag    boolean
   |        |  +--rw exclude-flag    boolean
   |        +--rw per-session-agg-max-ul
   |        |  +--rw max-rate        uint32
   |        |  +--rw service-flag    boolean
   |        |  +--rw exclude-flag    boolean
   |        +--rw priority-level                  uint8
   |        +--rw preemption-capability            enumeration
   |        +--rw preemption-vulnerability         enumeration
   |        +--rw agg-max-dl?
                    qos-pmip:Aggregate-Max-DL-Bit-Rate-Value
   |        +--rw agg-max-ul?
                    qos-pmip:Aggregate-Max-UL-Bit-Rate-Value



Matsushima, et al.      Expires December 20, 2018             [Page 141]


Internet-Draft              DMM FPC Protocol                   June 2018


   |        +--rw gbr-dl?
                    qos-pmip:Guaranteed-DL-Bit-Rate-Value
   |        +--rw gbr-ul?
                    qos-pmip:Guaranteed-UL-Bit-Rate-Value
   |        +--rw qci?
                    fpcbase:fpc-qos-class-identifier
   |        +--rw ue-agg-max-bitrate?             uint32
   |        +--rw apn-ambr?                       uint32

   policy-configuration-value:
   |  |  |     +--rw (policy-configuration-value)?
   |  |  |        +--:(descriptor-value)
   |  |  |        |  ...
   |  |  |        +--:(action-value)
   |  |  |        |  ...
   |  |  |        +--:(setting-value)
   |  |  |           +--rw setting?                        <anydata>

   policy-configuration:
   |  |  |  +--rw policy-configuration* [index]
   |  |  |     +--rw index                           uint16
   |  |  |     +--rw extensible?             boolean
   |  |  |     +--rw static-attributes*      string
   |  |  |     +--rw mandatory-attributes*   string
   |  |  |     +--rw entity-state?           enumeration
   |  |  |     +--rw version?                uint32
   |  |  |     +--rw (policy-configuration-value)?
   |  |  |        ...

   module: ietf-dmm-fpc
   +--rw tenant* [tenant-key]
     +--rw tenant-key                    fpc:fpc-identity
     +--rw topology-information-model
     |  +--rw service-group* [service-group-key role-key]
     |  |  +--rw service-group-key     fpc:fpc-identity
     |  |  +--rw service-group-name?   string
     |  |  +--rw role-key              identityref
     |  |  +--rw role-name?            string
     |  |  +--rw protocol*             identityref
     |  |  +--rw feature*              identityref
     |  |  +--rw service-group-configuration* [index]
     |  |  |  +--rw index                           uint16
     |  |  |  +--rw (policy-configuration-value)?
     |  |  |        |  ...
     |  |  +--rw dpn* [dpn-key]
     |  |     +--rw dpn-key                 fpc:fpc-identity
     |  |     +--rw referenced-interface* [interface-key]
     |  |        +--rw interface-key             fpc:fpc-identity



Matsushima, et al.      Expires December 20, 2018             [Page 142]


Internet-Draft              DMM FPC Protocol                   June 2018


     |  |        +--rw peer-service-group-key*   fpc:fpc-identity
     |  +--rw dpn* [dpn-key]
     |  |  +--rw dpn-key                           fpc:fpc-identity
     |  |  +--rw dpn-name?                         string
     |  |  +--rw dpn-resource-mapping-reference?   string
     |  |  +--rw domain-key                        fpc:fpc-identity
     |  |  +--rw service-group-key*                fpc:fpc-identity
     |  |  +--rw interface* [interface-key]
     |  |  |  +--rw interface-key        fpc:fpc-identity
     |  |  |  +--rw interface-name?      string
     |  |  |  +--rw role?                identityref
     |  |  |  +--rw protocol*            identityref
     |  |  |  +--rw interface-configuration* [index]
     |  |  |     +--rw (policy-configuration-value)?
     |  |  |           |  ...
     |  |  +--rw dpn-policy-configuration* [policy-template-key]
     |  |     +--rw policy-template-key     fpc:fpc-identity
     |  |     +--rw policy-configuration* [index]
     |  |        +--rw index    uint16
     |  |          +--rw (policy-configuration-value)?
     |  |               |  ...
     |  +--rw domain* [domain-key]
     |  |  +--rw domain-key        fpc:fpc-identity
     |  |  +--rw domain-name?      string
     |  |  +--rw domain-policy-configuration* [policy-template-key]
     |  |     +--rw policy-template-key     fpc:fpc-identity
     |  |     +--rw policy-configuration* [index]
     |  |              |         ...
     |  +--rw dpn-checkpoint
     |  |  +--rw basename?          fpc:fpc-identity
     |  |  +--rw base-checkpoint?   string
     |  +--rw service-group-checkpoint
     |  |  +--rw basename?          fpc:fpc-identity
     |  |  +--rw base-checkpoint?   string
     |  +--rw dpn-checkpoint
     |  |  +--rw basename?                   fpc:fpc-identity
     |  |  +--rw base-checkpoint?            string
     +--rw policy-information-model
     |  +--rw action-template* [action-template-key]
     |  |  +--rw action-template-key        fpc:fpc-identity
     |  |  +--rw (action-value)
     |  |  |                   ...
     |  |  +--rw extensible?                boolean
     |  |  +--rw static-attributes*         string
     |  |  +--rw mandatory-attributes*      string
     |  |  +--rw entity-state?              enumeration
     |  |  +--rw version?                   uint32
     |  +--rw descriptor-template* [descriptor-template-key]



Matsushima, et al.      Expires December 20, 2018             [Page 143]


Internet-Draft              DMM FPC Protocol                   June 2018


     |  |  +--rw descriptor-template-key         fpc:fpc-identity
     |  |  +--rw (descriptor-value)
     |  |  |                   ...
     |  |  +--rw extensible?                     boolean
     |  |  +--rw static-attributes*              string
     |  |  +--rw mandatory-attributes*           string
     |  |  +--rw entity-state?                   enumeration
     |  |  +--rw version?                        uint32
     |  +--rw rule-template* [rule-template-key]
     |  |  +--rw rule-template-key           fpc:fpc-identity
     |  |  +--rw descriptor-match-type       enumeration
     |  |  +--rw descriptor-configuration* [descriptor-template-key]
     |  |  |  +--rw descriptor-template-key    fpc:fpc-identity
     |  |  |  +--rw direction?                 rfc5777:direction-type
     |  |  |  +--rw setting?                        <anydata>
     |  |  |  +--rw attribute-expression* [index]
     |  |  |     +--rw index                           uint16
     |  |  |     +--rw (descriptor-value)
     |  |  |     |  ...
     |  |  +--rw action-configuration* [action-order]
     |  |  |  +--rw action-order            uint32
     |  |  |  +--rw action-template-key     fpc:fpc-identity
     |  |  |  +--rw setting?                        <anydata>
     |  |  |  +--rw attribute-expression* [index]
     |  |  |     +--rw index                      uint16
     |  |  |     +--rw (action-value)
     |  |  |     |  ...
     |  |  +--rw extensible?                 boolean
     |  |  +--rw static-attributes*          string
     |  |  +--rw mandatory-attributes*       string
     |  |  +--rw entity-state?               enumeration
     |  |  +--rw version?                    uint32
     |  |  +--rw rule-configuration* [index]
     |  |     +--rw index    uint16
     |  |         +--rw (policy-configuration-value)?
     |  |           |  ...
     |  +--rw policy-template* [policy-template-key]
     |  |  +--rw policy-template-key     fpc:fpc-identity
     |  |  +--rw rule-template* [precedence]
     |  |  |  +--rw precedence           uint32
     |  |  |  +--rw rule-template-key    fpc:fpc-identity
     |  |  +--rw extensible?             boolean
     |  |  +--rw static-attributes*      string
     |  |  +--rw mandatory-attributes*   string
     |  |  +--rw entity-state?           enumeration
     |  |  +--rw version?                uint32
     |  |  +--rw policy-configuration* [index]
     |  |      ...



Matsushima, et al.      Expires December 20, 2018             [Page 144]


Internet-Draft              DMM FPC Protocol                   June 2018


     |  +--rw basename?              fpc:fpc-identity
     |  +--rw base-checkpoint?       string
     +--rw mobility-context* [mobility-context-key]
     |  +--rw mobility-context-key    fpc:fpc-identity
     |  +--rw delegating-ip-prefix*   inet:ip-prefix
     |  +--rw parent-context?         fpc:fpc-identity
     |  +--rw child-context*          fpc:fpc-identity
     |  +--rw mobile-node
     |  |  +--rw ip-address*    inet:ip-address
     |  |  +--rw imsi?          fpcbase:imsi-type
     |  |  +--rw mn-policy-configuration* [policy-template-key]
     |  |     +--rw policy-template-key     fpc:fpc-identity
     |  |     +--rw policy-configuration* [index]
     |  |        ...
     |  +--rw domain
     |  |  +--rw domain-key?        fpc:fpc-identity
     |  |  +--rw domain-policy-configuration* [policy-template-key]
     |  |     +--rw policy-template-key     fpc:fpc-identity
     |  |     +--rw policy-configuration* [index]
     |  |        ...
     |   +--rw dpn* [dpn-key]
     |      +--rw dpn-key              fpc:fpc-identity
     |      +--rw dpn-policy-configuration* [policy-template-key]
     |      |  +--rw policy-template-key     fpc:fpc-identity
     |      |  +--rw policy-configuration* [index]
     |      |     ...
     |      +--rw role?                identityref
     |      +--rw service-data-flow* [identifier]
     |         +--rw identifier           uint32
     |         +--rw service-group-key?   fpc:fpc-identity
     |         +--rw interface* [interface-key]
     |         |  +--rw interface-key    fpc:fpc-identity
     |         +--rw service-data-flow-policy-
                       configuration* [policy-template-key]
     |            +--rw policy-template-key     fpc:fpc-identity
     |            +--rw policy-configuration* [index]
     |               ...
     +--rw monitor* [monitor-key]
       +--rw extensible?             boolean
       +--rw static-attributes*      string
       +--rw mandatory-attributes*   string
       +--rw entity-state?           enumeration
       +--rw version?                uint32
       +--rw monitor-key             fpc:fpc-identity
       +--rw target?                 string
       +--rw deferrable?             boolean
       +--rw (configuration)
          +--:(period)



Matsushima, et al.      Expires December 20, 2018             [Page 145]


Internet-Draft              DMM FPC Protocol                   June 2018


          |  +--rw period?           uint32
          +--:(threshold-config)
          |  +--rw low?              uint32
          |  +--rw hi?               uint32
          +--:(schedule)
          |  +--rw schedule?         uint32
          +--:(event-identities)
          |  +--rw event-identities*       identityref
          +--:(event-ids)
             +--rw event-ids*        uint32

     rpcs:
       +---x configure
       |  +---w input
       |  |  +---w client-id          fpc:client-identifier
       |  |  +---w execution-delay?   uint32
       |  |  +---w yang-patch
       |  |     +---w patch-id    string
       |  |     +---w comment?    string
       |  |     +---w edit* [edit-id]
       |  |        +---w edit-id         string
       |  |        +---w operation       enumeration
       |  |        +---w target          target-resource-offset
       |  |        +---w point?          target-resource-offset
       |  |        +---w where?          enumeration
       |  |        +---w value?          <anydata>
       |  |        +---w reference-scope?   fpc:ref-scope
       |  |        +---w command-set
       |  |           +---w (instr-type)?
       |  |              +--:(instr-3gpp-mob)
       |  |              |  +---w instr-3gpp-mob? fpcbase:threegpp-instr
       |  |              +--:(instr-pmip)
       |  |                 +---w instr-pmip?       pmip-commandset
       |  +--ro output
       |     +--ro yang-patch-status
       |        +--ro patch-id       string
       |        +--ro (global-status)?
       |        |  +--:(global-errors)
       |        |  |  +--ro errors
       |        |  |     +--ro error*
       |        |  |        +--ro error-type       enumeration
       |        |  |        +--ro error-tag        string
       |        |  |        +--ro error-app-tag?   string
       |        |  |        +--ro error-path?      instance-identifier
       |        |  |        +--ro error-message?   string
       |        |  |        +--ro error-info?      <anydata>
       |        |  +--:(ok)
       |        |     +--ro ok?            empty



Matsushima, et al.      Expires December 20, 2018             [Page 146]


Internet-Draft              DMM FPC Protocol                   June 2018


       |        +--ro edit-status
       |           +--ro edit* [edit-id]
       |              +--ro edit-id            string
       |              +--ro (edit-status-choice)?
       |                 +--:(ok)
       |                 |  +--ro ok?                empty
       |                 |  +--ro notify-follows?    boolean
       |                 |  +--ro subsequent-edit* [edit-id]
       |                 |     +--ro edit-id      string
       |                 |     +--ro operation    enumeration
       |                 |     +--ro target
                                   ypatch:target-resource-offset
       |                 |     +--ro point?
                                       ypatch:target-resource-offset
       |                 |     +--ro where?       enumeration
       |                 |     +--ro value?       <anydata>
       |                 +--:(errors)
       |                    +--ro errors
       |                       +--ro error*
       |                          +--ro error-type       enumeration
       |                          +--ro error-tag        string
       |                          +--ro error-app-tag?   string
       |                          +--ro error-path?
                                           instance-identifier
       |                          +--ro error-message?   string
       |                          +--ro error-info?      <anydata>
       +---x register_monitor
       |  +---w input
       |  |  +---w client-id          fpc:client-identifier
       |  |  +---w execution-delay?   uint32
       |  |  +---w operation-id              uint64
       |  |  +---w monitor* [monitor-key]
       |  |     +---w extensible?             boolean
       |  |     +---w static-attributes*      string
       |  |     +---w mandatory-attributes*   string
       |  |     +---w entity-state?           enumeration
       |  |     +---w version?                uint32
       |  |     +---w monitor-key             fpc:fpc-identity
       |  |     +---w target?                 string
       |  |     +---w deferrable?             boolean
       |  |     +---w (configuration)
       |  |        +--:(period)
       |  |        |  +---w period?                 uint32
       |  |        +--:(threshold-config)
       |  |        |  +---w low?                    uint32
       |  |        |  +---w hi?                     uint32
       |  |        +--:(schedule)
       |  |        |  +---w schedule?               uint32



Matsushima, et al.      Expires December 20, 2018             [Page 147]


Internet-Draft              DMM FPC Protocol                   June 2018


       |  |        +--:(event-identities)
       |  |        |  +---w event-identities*       identityref
       |  |        +--:(event-ids)
       |  |           +---w event-ids*              uint32
       |  +--ro output
       |     +--ro operation-id     uint64
       |     +--ro (edit-status-choice)?
       |        +--:(ok)
       |        |  +--ro ok?       empty
       |        +--:(errors)
       |           +--ro errors
       |              +--ro error*
       |                 +--ro error-type       enumeration
       |                 +--ro error-tag        string
       |                 +--ro error-app-tag?   string
       |                 +--ro error-path?      instance-identifier
       |                 +--ro error-message?   string
       |                 +--ro error-info?      <anydata>
       +---x deregister_monitor
       |  +---w input
       |  |  +---w client-id          fpc:client-identifier
       |  |  +---w execution-delay?   uint32
       |  |  +---w operation-id              uint64
       |  |  +---w monitor* [monitor-key]
       |  |     +---w monitor-key    fpc:fpc-identity
       |  |     +---w send_data?     boolean
       |  +--ro output
       |     +--ro operation-id     uint64
       |     +--ro (edit-status-choice)?
       |        +--:(ok)
       |        |  +--ro ok?       empty
       |        +--:(errors)
       |           +--ro errors
       |              +--ro error*
       |                 +--ro error-type       enumeration
       |                 +--ro error-tag        string
       |                 +--ro error-app-tag?   string
       |                 +--ro error-path?      instance-identifier
       |                 +--ro error-message?   string
       |                 +--ro error-info?      <anydata>
       +---x probe
          +---w input
          |  +---w client-id          fpc:client-identifier
          |  +---w execution-delay?   uint32
          |  +---w operation-id              uint64
          |  +---w monitor* [monitor-key]
          |     +---w monitor-key    fpc:fpc-identity
          +--ro output



Matsushima, et al.      Expires December 20, 2018             [Page 148]


Internet-Draft              DMM FPC Protocol                   June 2018


             +--ro operation-id     uint64
             +--ro (edit-status-choice)?
                +--:(ok)
                |  +--ro ok?       empty
                +--:(errors)
                   +--ro errors
                      +--ro error*
                         +--ro error-type       enumeration
                         +--ro error-tag        string
                         +--ro error-app-tag?   string
                         +--ro error-path?      instance-identifier
                         +--ro error-message?   string
                         +--ro error-info?      <anydata>

     notifications:
       +---n config-result-notification
       |  +--ro yang-patch-status
       |  |  +--ro patch-id       string
       |  |  +--ro (global-status)?
       |  |  |  +--:(global-errors)
       |  |  |  |  +--ro errors
       |  |  |  |     +--ro error*
       |  |  |  |        +--ro error-type       enumeration
       |  |  |  |        +--ro error-tag        string
       |  |  |  |        +--ro error-app-tag?   string
       |  |  |  |        +--ro error-path?      instance-identifier
       |  |  |  |        +--ro error-message?   string
       |  |  |  |        +--ro error-info?      <anydata>
       |  |  |  +--:(ok)
       |  |  |     +--ro ok?            empty
       |  |  +--ro edit-status
       |  |     +--ro edit* [edit-id]
       |  |        +--ro edit-id    string
       |  |        +--ro (edit-status-choice)?
       |  |           +--:(ok)
       |  |           |  +--ro ok?        empty
       |  |           +--:(errors)
       |  |              +--ro errors
       |  |                 +--ro error*
       |  |                    +--ro error-type       enumeration
       |  |                    +--ro error-tag        string
       |  |                    +--ro error-app-tag?   string
       |  |                    +--ro error-path?
                                       instance-identifier
       |  |                    +--ro error-message?   string
       |  |                    +--ro error-info?      <anydata>
       |  +--ro subsequent-edit* [edit-id]
       |     +--ro edit-id      string



Matsushima, et al.      Expires December 20, 2018             [Page 149]


Internet-Draft              DMM FPC Protocol                   June 2018


       |     +--ro operation    enumeration
       |     +--ro target       ypatch:target-resource-offset
       |     +--ro point?       ypatch:target-resource-offset
       |     +--ro where?       enumeration
       |     +--ro value?       <anydata>
       +---n notify
          +--ro notification-id?   uint32
          +--ro timestamp?         uint32
          +--ro report* [monitor-key]
             +--ro monitor-key                 fpc:fpc-identity
             +--ro trigger?                    identityref
             +--ro (value)?
                +--:(dpn-candidate-available)
                |  +--ro node-id?                    inet:uri
                |  +--ro supported-interface-list* [role-key]
                |     +--ro role-key    identityref
                +--:(dpn-unavailable)
                |  +--ro dpn-id?                     fpc:fpc-identity
                +--:(report-value)
                   +--ro report-value?               <anydata>

                      Figure 38: YANG FPC Agent Tree

Appendix C.  Change Log

C.1.  Changes since Version 09

   The following changes have been made since version 09

      Migration to a Template based framework.  This affects all
      elements.  The framework has a template definition language.

      Basename is split into two aspects.  The first is version which
      applies to Templates.  The second is checkpointing which applies
      to specific sections only.

      Rule was inside Policy and now is Rule-Template and stands as a
      peer structure to Policy.

      Types, e.g.  Descriptor Types, Action Types, etc., are now
      templates that have no values filled in.

      The embedded rule has been replaced by a template that has no
      predefined variables.  All rules, pre-configured or embedded, are
      realized as Policy instantiations.

      The Unassigned DPN is used to track requests vs.  those that are
      installed, i.e. Agent assignment of Policy is supported.



Matsushima, et al.      Expires December 20, 2018             [Page 150]


Internet-Draft              DMM FPC Protocol                   June 2018


      The Topology system supports selection information by ServiceGroup
      or ServiceEndpoint.

      DPN Peer Groups and DPN Groups are now PeerServiceGroup and
      ServiceGroup.

      Bulk Configuration and Configuration now follow a style similar to
      YANG Patch.  Agents MAY response back with edits it made to
      complete the Client edit request.

      RFC 5777 Classifiers have been added.

      All operations have a common error format.

C.2.  Changes since Version 10

   The following changes have been made since version 10

      Sevice-Endpoints eliminated.  Service-Group and DPN interfaces
      changed to hold information previously held by Service-Endpoint as
      noted in ML during IETF 101.

      Service-Group resides under the Topology-Information-Mode

      The Domain now has a checkpoint and the Topology Information Model
      checkpoint was removed to avoid any overlaps in checkpoints.

      Scrubbed YANG for NMDA compliance and Guidelines (RFC 6087bis).

      Monitor lifecycle, policy and policy installation examples added.

Authors' Addresses

   Satoru Matsushima
   SoftBank
   1-9-1,Higashi-Shimbashi,Minato-Ku
   Tokyo  105-7322
   Japan

   Email: satoru.matsushima@g.softbank.co.jp


   Lyle Bertz
   6220 Sprint Parkway
   Overland Park  KS, 66251
   USA

   Email: lylebe551144@gmail.com



Matsushima, et al.      Expires December 20, 2018             [Page 151]


Internet-Draft              DMM FPC Protocol                   June 2018


   Marco Liebsch
   NEC Laboratories Europe
   NEC Europe Ltd.
   Kurfuersten-Anlage 36
   D-69115 Heidelberg
   Germany

   Phone: +49 6221 4342146
   Email: liebsch@neclab.eu


   Sri Gundavelli
   Cisco
   170 West Tasman Drive
   San Jose, CA  95134
   USA

   Email: sgundave@cisco.com


   Danny Moses

   Email: danny.moses@intel.com


   Charles E. Perkins
   Futurewei Inc.
   2330 Central Expressway
   Santa Clara, CA  95050
   USA

   Phone: +1-408-330-4586
   Email: charliep@computer.org


















Matsushima, et al.      Expires December 20, 2018             [Page 152]