DOTS                                                   M. Boucadair, Ed.
Internet-Draft                                                    Orange
Intended status: Standards Track                           T. Reddy, Ed.
Expires: January 4, 2020                                          McAfee
                                                           July 03, 2019


Distributed Denial-of-Service Open Threat Signaling (DOTS) Data Channel
                             Specification
                    draft-ietf-dots-data-channel-30

Abstract

   The document specifies a Distributed Denial-of-Service Open Threat
   Signaling (DOTS) data channel used for bulk exchange of data that
   cannot easily or appropriately communicated through the DOTS signal
   channel under attack conditions.

   This is a companion document to the DOTS signal channel
   specification.

Editorial Note (To be removed by RFC Editor)

   Please update these statements within the document with the RFC
   number to be assigned to this document:

   o  "This version of this YANG module is part of RFC XXXX;"

   o  "RFC XXXX: Distributed Denial-of-Service Open Threat Signaling
      (DOTS) Data Channel Specification";

   o  reference: RFC XXXX

   Please update the "revision" date of the YANG module.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any




Boucadair & Reddy        Expires January 4, 2020                [Page 1]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 4, 2020.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   5
   3.  DOTS Data Channel . . . . . . . . . . . . . . . . . . . . . .   5
     3.1.  Design Overview . . . . . . . . . . . . . . . . . . . . .   5
     3.2.  DOTS Server(s) Discovery  . . . . . . . . . . . . . . . .   8
     3.3.  DOTS Gateways . . . . . . . . . . . . . . . . . . . . . .   8
     3.4.  Detect and Prevent Infinite Loops . . . . . . . . . . . .   9
     3.5.  Stale Entries . . . . . . . . . . . . . . . . . . . . . .   9
   4.  DOTS Data Channel YANG Module . . . . . . . . . . . . . . . .  10
     4.1.  Generic Tree Structure  . . . . . . . . . . . . . . . . .  10
     4.2.  Filtering Fields  . . . . . . . . . . . . . . . . . . . .  13
     4.3.  YANG Module . . . . . . . . . . . . . . . . . . . . . . .  20
   5.  Managing DOTS Clients . . . . . . . . . . . . . . . . . . . .  37
     5.1.  Registering DOTS Clients  . . . . . . . . . . . . . . . .  37
     5.2.  Unregistering DOTS Clients  . . . . . . . . . . . . . . .  40
   6.  Managing DOTS Aliases . . . . . . . . . . . . . . . . . . . .  40
     6.1.  Create Aliases  . . . . . . . . . . . . . . . . . . . . .  41
     6.2.  Retrieve Installed Aliases  . . . . . . . . . . . . . . .  45
     6.3.  Delete Aliases  . . . . . . . . . . . . . . . . . . . . .  47
   7.  Managing DOTS Filtering Rules . . . . . . . . . . . . . . . .  47
     7.1.  Retrieve DOTS Filtering Capabilities  . . . . . . . . . .  47
     7.2.  Install Filtering Rules . . . . . . . . . . . . . . . . .  49
     7.3.  Retrieve Installed Filtering Rules  . . . . . . . . . . .  52
     7.4.  Remove Filtering Rules  . . . . . . . . . . . . . . . . .  59
   8.  Operational Considerations  . . . . . . . . . . . . . . . . .  60
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  60



Boucadair & Reddy        Expires January 4, 2020                [Page 2]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   10. Security Considerations . . . . . . . . . . . . . . . . . . .  61
   11. Contributing Authors  . . . . . . . . . . . . . . . . . . . .  63
   12. Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  64
   13. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  65
   14. References  . . . . . . . . . . . . . . . . . . . . . . . . .  65
     14.1.  Normative References . . . . . . . . . . . . . . . . . .  65
     14.2.  Informative References . . . . . . . . . . . . . . . . .  66
   Appendix A.  Sample Examples: Filtering Fragments . . . . . . . .  68
   Appendix B.  Sample Examples: Filtering TCP Messages  . . . . . .  71
     B.1.  Discard TCP Null Attack . . . . . . . . . . . . . . . . .  71
     B.2.  Rate-Limit SYN Flooding . . . . . . . . . . . . . . . . .  72
     B.3.  Rate-Limit ACK Flooding . . . . . . . . . . . . . . . . .  73
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  74

1.  Introduction

   A distributed denial-of-service (DDoS) attack is an attempt to make
   machines or network resources unavailable to their intended users.
   In most cases, sufficient scale can be achieved by compromising
   enough end-hosts and using those infected hosts to perpetrate and
   amplify the attack.  The victim of such attack can be an application
   server, a router, a firewall, an entire network, etc.

   As discussed in [RFC8612], the lack of a common method to coordinate
   a real-time response among involved actors and network domains
   inhibits the speed and effectiveness of DDoS attack mitigation.  From
   that standpoint, DDoS Open Threat Signaling (DOTS) defines an
   architecture that allows a DOTS client to send requests to a DOTS
   server for DDoS attack mitigation [I-D.ietf-dots-architecture].  The
   DOTS approach is thus meant to minimize the impact of DDoS attacks,
   thereby contributing to the enforcement of more efficient defensive
   if not proactive security strategies.  To that aim, DOTS defines two
   channels: the signal and the data channels (Figure 1).

   +---------------+                                 +---------------+
   |               | <------- Signal Channel ------> |               |
   |  DOTS Client  |                                 |  DOTS Server  |
   |               | <=======  Data Channel  ======> |               |
   +---------------+                                 +---------------+

                          Figure 1: DOTS Channels

   The DOTS signal channel is used to carry information about a device
   or a network (or a part thereof) that is under a DDoS attack.  Such
   information is sent by a DOTS client to an upstream DOTS server so
   that appropriate mitigation actions are undertaken on traffic deemed
   suspicious.  The DOTS signal channel is further elaborated in
   [I-D.ietf-dots-signal-channel].



Boucadair & Reddy        Expires January 4, 2020                [Page 3]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   As for the DOTS data channel, it is used for infrequent bulk data
   exchange between DOTS agents to significantly improve the
   coordination of all the parties involved in the response to the
   attack.  Section 2 of [I-D.ietf-dots-architecture] mentions that the
   DOTS data channel is used to perform the following tasks:

   o  Creating aliases for resources for which mitigation may be
      requested.

      A DOTS client may submit to its DOTS server a collection of
      prefixes which it would like to refer to by an alias when
      requesting mitigation.  The DOTS server can respond to this
      request with either a success or failure response (see Section 2
      in [I-D.ietf-dots-architecture]).

      Refer to Section 6 for more details.

   o  Policy management, which enables a DOTS client to request the
      installation or withdrawal of traffic filters, dropping or rate-
      limiting unwanted traffic, and permitting accept-listed traffic.
      A DOTS client is entitled to instruct filtering rules only on IP
      resources that belong to its domain.

      Sample use cases for populating drop- or accept-list filtering
      rules are detailed hereafter:

      *  If a network resource (DOTS client) is informed about a
         potential DDoS attack from a set of IP addresses, the DOTS
         client informs its servicing DOTS gateway of all suspect IP
         addresses that need to be drop-listed for further
         investigation.  The DOTS client could also specify a list of
         protocols and port numbers in the drop-list rule.

         The DOTS gateway then propagates the drop-listed IP addresses
         to a DOTS server which will undertake appropriate actions so
         that traffic originated by these IP addresses to the target
         network (specified by the DOTS client) is blocked.

      *  A network, that has partner sites from which only legitimate
         traffic arrives, may want to ensure that the traffic from these
         sites is not subjected to DDoS attack mitigation.  The DOTS
         client uses the DOTS data channel to convey the accept-listed
         IP prefixes of the partner sites to its DOTS server.

         The DOTS server uses this information to accept-list flows
         originated by such IP prefixes and which reach the network.

      Refer to Section 7 for more details.



Boucadair & Reddy        Expires January 4, 2020                [Page 4]


Internet-Draft         DOTS Data Channel Protocol              July 2019


2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119] [RFC8174] when, and only when, they appear in all capitals,
   as shown here.

   The reader should be familiar with the terms defined in [RFC8612].

   The terminology for describing YANG modules is defined in [RFC7950].
   The meaning of the symbols in the tree diagrams is defined in
   [RFC8340].

   This document generalizes the notion of Access Control List (ACL) so
   that it is not device-specific [RFC8519].  As such, this document
   defines an ACL as an ordered set of rules that is used to filter
   traffic.  Each rule is represented by an Access Control Entry (ACE).
   ACLs communicated via the DOTS data channel are not bound to a device
   interface.

   For the sake of simplicity, all of the examples in this document use
   "/restconf" as the discovered RESTCONF API root path.  Many protocol
   header lines and message-body text within examples throughout the
   document are split into multiple lines for display purposes only.
   When a line ends with backslash ('\') as the last character, the line
   is wrapped for display purposes.  It is to be considered to be joined
   to the next line by deleting the backslash, the following line break,
   and the leading whitespace of the next line.

3.  DOTS Data Channel

3.1.  Design Overview

   Unlike the DOTS signal channel, which must remain operational even
   when confronted with signal degradation due to packets loss, the DOTS
   data channel is not expected to be fully operational at all times,
   especially when a DDoS attack is underway.  The requirements for a
   DOTS data channel protocol are documented in [RFC8612].

   This specification does not require an order of DOTS signal and data
   channel creations nor mandates a time interval between them.  These
   considerations are implementation- and deployment-specific.

   As the primary function of the data channel is data exchange, a
   reliable transport mode is required in order for DOTS agents to
   detect data delivery success or failure.  This document uses RESTCONF




Boucadair & Reddy        Expires January 4, 2020                [Page 5]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   [RFC8040] over TLS over TCP as the DOTS data channel protocol.  The
   abstract layering of DOTS data channel is shown in Figure 2.

                           +-------------------+
                           | DOTS Data Channel |
                           +-------------------+
                           |      RESTCONF     |
                           +-------------------+
                           |        TLS        |
                           +-------------------+
                           |        TCP        |
                           +-------------------+
                           |        IP         |
                           +-------------------+

             Figure 2: Abstract Layering of DOTS Data Channel

   The HTTP POST, PUT, PATCH, and DELETE methods are used to edit data
   resources represented by DOTS data channel YANG modules.  These basic
   edit operations allow the DOTS data channel running configuration to
   be altered by a DOTS client.  Rules for generating and processing
   RESTCONF methods are defined in Section 4 of [RFC8040].

   DOTS data channel configuration information as well as state
   information can be retrieved with the GET method.  An HTTP status-
   line is returned for each request to report success or failure for
   RESTCONF operations (Section 5.4 of [RFC8040]).  The "error-tag"
   provides more information about encountered errors (Section 7 of
   [RFC8040]).

   DOTS clients perform the root resource discovery procedure discussed
   in Section 3.1 of [RFC8040] to determine the root of the RESTCONF
   API.  After discovering the RESTCONF API root, a DOTS client uses
   this value as the initial part of the path in the request URI in any
   subsequent request to the DOTS server.  The DOTS server may support
   the retrieval of the YANG modules it supports (Section 3.7 in
   [RFC8040]).  For example, a DOTS client may use RESTCONF to retrieve
   the vendor-specific YANG modules supported by its DOTS server.

   JavaScript Object Notation (JSON) [RFC8259] payloads are used to
   propagate the DOTS data-channel-specific payload messages that carry
   request parameters and response information, such as errors.  This
   specification uses the encoding rules defined in [RFC7951] for
   representing DOTS data channel configuration data using YANG
   (Section 4) as JSON text.

   A DOTS client registers itself to its DOTS server(s) in order to set
   up DOTS data channel-related configuration data and receive state



Boucadair & Reddy        Expires January 4, 2020                [Page 6]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   data (i.e., non-configuration data) from the DOTS server(s)
   (Section 5).  Mutual authentication considerations are specified in
   Section 8 of [I-D.ietf-dots-signal-channel].  The coupling of signal
   and data channels is discussed in Section 4.4.1 of
   [I-D.ietf-dots-signal-channel].

   A DOTS client can either maintain a persistent connection or periodic
   connections with its DOTS server(s).  If the DOTS client needs to
   frequently update the drop-list or accept-list filtering rules or
   aliases, it maintains a persistent connection with the DOTS server.
   For example, CAPTCHA and cryptographic puzzles can be used by the
   mitigation service in the DOTS client domain to determine whether the
   IP address is used for legitimate purpose or not, and the DOTS client
   can frequently update the drop-list filtering rules.  A persistent
   connection is also useful if the DOTS client subscribes to event
   notifications (Section 6.3 of [RFC8040]).

   A single DOTS data channel between DOTS agents can be used to
   exchange multiple requests and multiple responses.  To reduce DOTS
   client and DOTS server workload, DOTS clients SHOULD re-use the same
   TLS session.  While the communication to the DOTS server is
   quiescent, the DOTS client MAY probe the server to ensure it has
   maintained cryptographic state.  Such probes can also keep alive
   firewall and/or NAT bindings.  A TLS heartbeat [RFC6520] verifies
   that the DOTS server still has TLS state by returning a TLS message.

   A DOTS server may detect conflicting filtering requests from distinct
   DOTS clients which belong to the same domain.  For example, a DOTS
   client could request to drop-list a prefix by specifying the source
   prefix, while another DOTS client could request to accept-list that
   same source prefix, but both having the same destination prefix.
   DOTS servers SHOULD support a configuration parameter to indicate the
   behavior to follow when a conflict is detected (e.g., reject all,
   reject the new request, notify an administrator for validation).
   Section 7.2 specifies a default behavior when no instruction is
   supplied to a DOTS server.

   How a DOTS client synchronizes its configuration with the one
   maintained by its DOTS server(s) is implementation-specific.  For
   example:

   o  a DOTS client can systematically send a GET message before and/or
      after a configuration change request.

   o  a DOTS client can re-establish the disconnected DOTS session after
      an attack is mitigated and sends a GET message before a
      configuration change request.




Boucadair & Reddy        Expires January 4, 2020                [Page 7]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   NAT considerations for the DOTS data channel are similar to those
   discussed in Section 3 of [I-D.ietf-dots-signal-channel].

   How filtering rules that are instantiated on a DOTS server are
   translated into network configurations actions is out of scope of
   this specification.

   Some of the fields introduced in Section 4 are also discussed in
   Sections 5, 6, and 7.  These sections are authoritative for these
   fields.

3.2.  DOTS Server(s) Discovery

   This document assumes that DOTS clients are provisioned with a way to
   know how to reach their DOTS server(s), which could occur by a
   variety of means (e.g., local configuration, or dynamic means such as
   DHCP [I-D.ietf-dots-server-discovery]).  The specification of such
   means are out of scope of this document.

   Likewise, it is out of scope of this document to specify the behavior
   to be followed by a DOTS client to send DOTS requests when multiple
   DOTS servers are provisioned (e.g., contact all DOTS servers, select
   one DOTS server among the list).

3.3.  DOTS Gateways

   When a server-domain DOTS gateway is involved in DOTS data channel
   exchanges, the same considerations for manipulating the 'cdid'
   (client domain identifier) parameter specified in
   [I-D.ietf-dots-signal-channel] MUST be followed by DOTS agents.  As a
   reminder, 'cdid' is meant to assist the DOTS server to enforce some
   policies (e.g., limit the number of filtering rules per DOTS client
   or per DOTS client domain).  A loop detect mechanism for DOTS
   gateways is specified in Section 3.4.

   If a DOTS gateway is involved, the DOTS gateway verifies that the
   DOTS client is authorized to undertake a data channel action (e.g.,
   instantiate filtering rules).  If the DOTS client is authorized, it
   propagates the rules to the upstream DOTS server.  Likewise, the DOTS
   server verifies that the DOTS gateway is authorized to relay data
   channel actions.  For example, to create or purge filters, a DOTS
   client sends its request to its DOTS gateway.  The DOTS gateway
   validates the rules in the request and proxies the requests
   containing the filtering rules to its DOTS server.  When the DOTS
   gateway receives the associated response from the DOTS server, it
   propagates the response back to the DOTS client.





Boucadair & Reddy        Expires January 4, 2020                [Page 8]


Internet-Draft         DOTS Data Channel Protocol              July 2019


3.4.  Detect and Prevent Infinite Loops

   In order to detect and prevent infinite loops, DOTS gateways MUST
   support the procedure defined in Section 5.7.1 of [RFC7230].  In
   particular, each intermediate DOTS gateway MUST check that none of
   its own information (e.g., server names, literal IP addresses) is
   present in the "Via" header field of a DOTS message it receives:

   o  If it detects that its own information is present in the "Via"
      header field, the DOTS gateway MUST NOT forward the DOTS message.
      Messages that cannot be forwarded because of a loop SHOULD be
      logged with a "508 Loop Detected" status-line returned sent back
      to the DOTS peer.  The structure of the reported error is depicted
      in Figure 3.



   error-app-tag:  loop-detected
   error-tag:      operation-failed
   error-type:     transport, application
   error-info:     <via-header> : A copy of the Via header field when
                   the loop was detected.
   Description:    An infinite loop has been detected when forwarding
                   a requests via a proxy.

                       Figure 3: Loop Detected Error

      It is RECOMMENDED that DOTS clients and gateways support methods
      to alert administrators about loop errors so that appropriate
      actions are undertaken.

   o  Otherwise, the DOTS agent MUST update or insert the "Via" header
      by appending its own information.

   Unless configured otherwise, DOTS gateways at the boundaries of a
   DOTS client domain SHOULD remove the previous "Via" header field
   information after checking for a loop before forwarding.  This
   behavior is required for topology hiding purposes but can also serve
   to minimize potential conflicts that may arise if overlapping
   information is used in distinct DOTS domains (e.g., private IPv4
   addresses, non globally unique aliases).

3.5.  Stale Entries

   In order to avoid stale entries, a lifetime is associated with alias
   and filtering entries created by DOTS clients.  Also, DOTS servers
   may track the inactivity timeout of DOTS clients to detect stale
   entries.



Boucadair & Reddy        Expires January 4, 2020                [Page 9]


Internet-Draft         DOTS Data Channel Protocol              July 2019


4.  DOTS Data Channel YANG Module

4.1.  Generic Tree Structure

   The DOTS data channel YANG module (ietf-dots-data-channel) provides a
   method for DOTS clients to manage aliases for resources for which
   mitigation may be requested.  Such aliases may be used in subsequent
   DOTS signal channel exchanges to refer more efficiently to the
   resources under attack.

   Note that the full module's tree has been split across several
   figures to aid the exposition of the various sub-trees.

   The tree structure for the DOTS alias is depicted in Figure 4.

   module: ietf-dots-data-channel
       +--rw dots-data
          +--rw dots-client* [cuid]
          |  +--rw cuid            string
          |  +--rw cdid?           string
          |  +--rw aliases
          |  |  +--rw alias* [name]
          |  |     +--rw name                 string
          |  |     +--rw target-prefix*       inet:ip-prefix
          |  |     +--rw target-port-range* [lower-port]
          |  |     |  +--rw lower-port    inet:port-number
          |  |     |  +--rw upper-port?   inet:port-number
          |  |     +--rw target-protocol*     uint8
          |  |     +--rw target-fqdn*         inet:domain-name
          |  |     +--rw target-uri*          inet:uri
          |  |     +--ro pending-lifetime?    int32
          |  +--rw acls
          |     ...
          +--ro capabilities
             ...

                       Figure 4: DOTS Alias Subtree

   Also, the 'ietf-dots-data-channel' module provides a method for DOTS
   clients to manage filtering rules.  Examples of filtering management
   in a DOTS context include, but not limited to:

   o  Drop-list management, which enables a DOTS client to inform a DOTS
      server about sources from which traffic should be discarded.

   o  Accept-list management, which enables a DOTS client to inform a
      DOTS server about sources from which traffic should always be
      accepted.



Boucadair & Reddy        Expires January 4, 2020               [Page 10]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   o  Policy management, which enables a DOTS client to request the
      installation or withdrawal of traffic filters, dropping or rate-
      limiting unwanted traffic and permitting accept-listed traffic.

   The tree structure for the DOTS filtering entries is depicted in
   Figure 5.

   Investigations into the prospect of augmenting 'ietf-access-control-
   list' to meet DOTS requirements concluded that such a design approach
   did not support many of the DOTS requirements, e.g.,

   o  Retrieve a filtering entry (or all entries) created by a DOTS
      client.

   o  Delete a filtering entry that was instantiated by a DOTS client.

   Accordingly, new DOTS filtering entries (i.e., Access Control List
   (ACL)) are defined that mimic the structure specified in [RFC8519].
   Concretely, DOTS agents are assumed to manipulate an ordered list of
   ACLs; each ACL contains a separately ordered list of Access Control
   Entries (ACEs).  Each ACE has a group of match and a group of action
   criteria.

   Once all the ACE entries have been iterated though with no match,
   then all the following ACL's ACE entries are iterated through until
   the first match at which point the specified action is applied.  If
   there is no match during 'idle' time (i.e., no mitigation is active),
   then there is no further action to be taken against the packet.  If
   there is no match during active mitigation, then the packet will
   still be scrubbed by the DDoS mitigator.





















Boucadair & Reddy        Expires January 4, 2020               [Page 11]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   module: ietf-dots-data-channel
       +--rw dots-data
          +--rw dots-client* [cuid]
          |  +--rw cuid            string
          |  +--rw cdid?           string
          |  +--rw aliases
          |  |  ...
          |  +--rw acls
          |     +--rw acl* [name]
          |        +--rw name                string
          |        +--rw type?               ietf-acl:acl-type
          |        +--rw activation-type?    activation-type
          |        +--ro pending-lifetime?   int32
          |        +--rw aces
          |           +--rw ace* [name]
          |              +--rw name          string
          |              +--rw matches
          |              |  +--rw (l3)?
          |              |  |  +--:(ipv4)
          |              |  |  |  ...
          |              |  |  +--:(ipv6)
          |              |  |     ...
          |              |  +--rw (l4)?
          |              |     +--:(tcp)
          |              |     |  ...
          |              |     +--:(udp)
          |              |     |  ...
          |              |     +--:(icmp)
          |              |        ...
          |              +--rw actions
          |              |  +--rw forwarding    identityref
          |              |  +--rw rate-limit?   decimal64
          |              +--ro statistics
          |                 +--ro matched-packets?   yang:counter64
          |                 +--ro matched-octets?    yang:counter64
          +--ro capabilities
             ...

                        Figure 5: DOTS ACLs Subtree

   Filtering rules instructed by a DOTS client assumes a default
   direction: the destination is the DOTS client domain.

   DOTS forwarding actions can be 'accept' (i.e., accept matching
   traffic) or 'drop' (i.e., drop matching traffic without sending any
   ICMP error message).  Accepted traffic can be subject to rate-
   limiting 'rate-limit'.  Note that 'reject' action (i.e., drop
   matching traffic and send an ICMP error message to the source) is not



Boucadair & Reddy        Expires January 4, 2020               [Page 12]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   supported in 'ietf-dots-data-channel' because it is not appropriate
   in the context of DDoS mitigation.  Generating ICMP messages to
   notify drops when mitigating a DDoS attack will exacerbate the DDoS
   attack.  Furthermore, these ICMP messages will be used by an attacker
   as an explicit signal that the traffic is being blocked.

4.2.  Filtering Fields

   The 'ietf-dots-data-channel' module reuses the packet fields module
   'ietf-packet-fields' [RFC8519] which defines matching on fields in
   the packet including IPv4, IPv6, and transport layer fields.  The
   'ietf-dots-data-channel' module can be augmented, for example, to
   support additional protocol-specific matching fields.

   This specification defines a new IPv4/IPv6 matching field called
   'fragment' to efficiently handle fragment-related filtering rules.
   Indeed, [RFC8519] does not support such capability for IPv6 but
   offers a partial support for IPv4 by means of 'flags'.  Nevertheless,
   the use of 'flags' is problematic since it does not allow to define a
   bitmask.  For example, setting other bits not covered by the 'flags'
   filtering clause in a packet will allow that packet to get through
   (because it won't match the ACE).  Sample examples to illustrate how
   'fragment' can be used are provided in Appendix A.

   Figure 6 shows the IPv4 match subtree.


























Boucadair & Reddy        Expires January 4, 2020               [Page 13]


Internet-Draft         DOTS Data Channel Protocol              July 2019


  module: ietf-dots-data-channel
    +--rw dots-data
       +--rw dots-client* [cuid]
       |  ...
       |  +--rw acls
       |     +--rw acl* [name]
       |        ...
       |        +--rw aces
       |           +--rw ace* [name]
       |              +--rw name          string
       |              +--rw matches
       |              |  +--rw (l3)?
       |              |  |  +--:(ipv4)
       |              |  |  |  +--rw ipv4
       |              |  |  |     +--rw dscp?                  inet:dscp
       |              |  |  |     +--rw ecn?                   uint8
       |              |  |  |     +--rw length?                uint16
       |              |  |  |     +--rw ttl?                   uint8
       |              |  |  |     +--rw protocol?              uint8
       |              |  |  |     +--rw ihl?                   uint8
       |              |  |  |     +--rw flags?                 bits
       |              |  |  |     +--rw offset?                uint16
       |              |  |  |     +--rw identification?        uint16
       |              |  |  |     +--rw (destination-network)?
       |              |  |  |     |  +--:(destination-ipv4-network)
       |              |  |  |     |     +--rw destination-ipv4-network?
       |              |  |  |     |             inet:ipv4-prefix
       |              |  |  |     +--rw (source-network)?
       |              |  |  |     |  +--:(source-ipv4-network)
       |              |  |  |     |     +--rw source-ipv4-network?
       |              |  |  |     |             inet:ipv4-prefix
       |              |  |  |     +--rw fragment
       |              |  |  |        +--rw operator?        operator
       |              |  |  |        +--rw type        fragment-type
       |              |  |  +--:(ipv6)
       |              |  |     ...
       |              |  +--rw (l4)?
       |              |     ...
       |              +--rw actions
       |              |  ...
       |              +--ro statistics
       |                 ...
       +--ro capabilities
          ...

                 Figure 6: DOTS ACLs Subtree (IPv4 Match)

   Figure 7 shows the IPv6 match subtree.



Boucadair & Reddy        Expires January 4, 2020               [Page 14]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   module: ietf-dots-data-channel
    +--rw dots-data
       +--rw dots-client* [cuid]
       |  ...
       |  +--rw acls
       |     +--rw acl* [name]
       |        ...
       |        +--rw aces
       |           +--rw ace* [name]
       |              +--rw name          string
       |              +--rw matches
       |              |  +--rw (l3)?
       |              |  |  +--:(ipv4)
       |              |  |  |  ...
       |              |  |  +--:(ipv6)
       |              |  |     +--rw ipv6
       |              |  |        +--rw dscp?                  inet:dscp
       |              |  |        +--rw ecn?                   uint8
       |              |  |        +--rw length?                uint16
       |              |  |        +--rw ttl?                   uint8
       |              |  |        +--rw protocol?              uint8
       |              |  |        +--rw (destination-network)?
       |              |  |        |  +--:(destination-ipv6-network)
       |              |  |        |     +--rw destination-ipv6-network?
       |              |  |        |             inet:ipv6-prefix
       |              |  |        +--rw (source-network)?
       |              |  |        |  +--:(source-ipv6-network)
       |              |  |        |     +--rw source-ipv6-network?
       |              |  |        |             inet:ipv6-prefix
       |              |  |        +--rw flow-label?
       |              |  |        |       inet:ipv6-flow-label
       |              |  |        +--rw fragment
       |              |  |           +--rw operator?       operator
       |              |  |           +--rw type       fragment-type
       |              |  +--rw (l4)?
       |              |     ...
       |              +--rw actions
       |              |  ...
       |              +--ro statistics
       |                 ...
       +--ro capabilities
          ...

                 Figure 7: DOTS ACLs Subtree (IPv6 Match)

   Figure 8 shows the TCP match subtree.  In addition to the fields
   defined in [RFC8519], this specification defines a new TCP matching




Boucadair & Reddy        Expires January 4, 2020               [Page 15]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   field, called 'flags-bitmask', to efficiently handle TCP flags
   filtering rules.  Some examples are provided in Appendix B.

   module: ietf-dots-data-channel
   +--rw dots-data
      +-rw dots-client* [cuid]
      | ...
      | +-rw acls
      |   +-rw acl* [name]
      |    ...
      |     +-rw aces
      |       +-rw ace* [name]
      |         +-rw name          string
      |           +-rw matches
      |           | +-rw (l3)?
      |           | | ...
      |           | +-rw (l4)?
      |           |   +-:(tcp)
      |           |   | +-rw tcp
      |           |   |   +--rw sequence-number?          uint32
      |           |   |   +--rw acknowledgement-number?   uint32
      |           |   |   +--rw data-offset?              uint8
      |           |   |   +--rw reserved?                 uint8
      |           |   |   +--rw flags?                    bits
      |           |   |   +--rw window-size?              uint16
      |           |   |   +--rw urgent-pointer?           uint16
      |           |   |   +--rw options?                  binary
      |           |   |   +--rw flags-bitmask
      |           |   |   |  +--rw operator?            operator
      |           |   |   |  +--rw bitmask                uint16
      |           |   |   +--rw (source-port)?
      |           |   |   |  +--:(source-port-range-or-operator)
      |           |   |   |     +--rw source-port-range-or-operator
      |           |   |   |        +--rw (port-range-or-operator)?
      |           |   |   |           +--:(range)
      |           |   |   |           |  +--rw lower-port
      |           |   |   |           |  |       inet:port-number
      |           |   |   |           |  +--rw upper-port
      |           |   |   |           |          inet:port-number
      |           |   |   |           +--:(operator)
      |           |   |   |              +--rw operator?
      |           |   |   |              |       operator
      |           |   |   |              +--rw port
      |           |   |   |                      inet:port-number
      |           |   |   +--rw (destination-port)?
      |           |   |      +--:(destination-port-range-or-operator)
      |           |   |         +--rw destination-port-range-or-operator
      |           |   |            +--rw (port-range-or-operator)?



Boucadair & Reddy        Expires January 4, 2020               [Page 16]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      |           |   |               +--:(range)
      |           |   |               |  +--rw lower-port
      |           |   |               |  |       inet:port-number
      |           |   |               |  +--rw upper-port
      |           |   |               |          inet:port-number
      |           |   |               +--:(operator)
      |           |   |                  +--rw operator?
      |           |   |                  |       operator
      |           |   |                  +--rw port
      |           |   |                          inet:port-number
      |           |   +-:(udp)
      |           |   | ...
      |           |   +-:(icmp)
      |           |     ...
      |           +-rw actions
      |           | ...
      |           +-ro statistics
      |             ...
      +-ro capabilities
        ...

                  Figure 8: DOTS ACLs Subtree (TCP Match)

   Figure 9 shows the UDP and ICMP match subtrees.  The same structure
   is used for both ICMP and ICMPv6.  The indication whether an ACL is
   about ICMP or ICMPv6 is governed by the 'l3' match or the ACL type.

 module: ietf-dots-data-channel
  +-rw dots-data
    +-rw dots-client* [cuid]
    | ...
    | +-rw acls
    |   +-rw acl* [name]
    |     ...
    |     +-rw aces
    |       +-rw ace* [name]
    |         +--rw name          string
    |         +--rw matches
    |         |  +--rw (l3)?
    |         |  |  ...
    |         |  +--rw (l4)?
    |         |     +--:(tcp)
    |         |     |  ...
    |         |     +--:(udp)
    |         |     |  +--rw udp
    |         |     |     +--rw length?          uint16
    |         |     |     +--rw (source-port)?
    |         |     |     |  +--:(source-port-range-or-operator)



Boucadair & Reddy        Expires January 4, 2020               [Page 17]


Internet-Draft         DOTS Data Channel Protocol              July 2019


    |         |     |     |     +--rw source-port-range-or-operator
    |         |     |     |        +--rw (port-range-or-operator)?
    |         |     |     |           +--:(range)
    |         |     |     |           |  +--rw lower-port
    |         |     |     |           |  |       inet:port-number
    |         |     |     |           |  +--rw upper-port
    |         |     |     |           |          inet:port-number
    |         |     |     |           +--:(operator)
    |         |     |     |              +--rw operator?
    |         |     |     |              |       operator
    |         |     |     |              +--rw port
    |         |     |     |                      inet:port-number
    |         |     |     +--rw (destination-port)?
    |         |     |        +--:(destination-port-range-or-operator)
    |         |     |           +--rw destination-port-range-or-operator
    |         |     |              +--rw (port-range-or-operator)?
    |         |     |                 +--:(range)
    |         |     |                 |  +--rw lower-port
    |         |     |                 |  |       inet:port-number
    |         |     |                 |  +--rw upper-port
    |         |     |                 |          inet:port-number
    |         |     |                 +--:(operator)
    |         |     |                    +--rw operator?
    |         |     |                    |       operator
    |         |     |                    +--rw port
    |         |     |                            inet:port-number
    |         |     +--:(icmp)
    |         |        +--rw icmp
    |         |           +--rw type?             uint8
    |         |           +--rw code?             uint8
    |         |           +--rw rest-of-header?   binary
    |         +--rw actions
    |         |  ...
    |         +--ro statistics
    |            ...
    +-ro capabilities
      ...

             Figure 9: DOTS ACLs Subtree (UDP and ICMP Match)

   DOTS implementations MUST support the following matching criteria:

      match based on the IP header (IPv4 and IPv6), match based on the
      transport header (TCP, UDP, and ICMP), and any combination
      thereof.  The same matching fields are used for both ICMP and
      ICMPv6.





Boucadair & Reddy        Expires January 4, 2020               [Page 18]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   The following match fields MUST be supported by DOTS implementations
   (Table 1):

   ACL     Mandatory Fields
   Match
   ------- -------------------------------------------------------------
   ipv4    length, protocol, destination-ipv4-network, source-
           ipv4-network, and fragment
   ipv6    length, protocol, destination-ipv6-network, source-
           ipv6-network, and fragment
   tcp     flags-bitmask, source-port-range-or-operator, and
           destination-port-range-or-operator
   udp     length, source-port-range-or-operator, and destination-port-
           range-or-operator
   icmp    type and code

               Table 1: Mandatory DOTS Channel Match Fields

   Implementations MAY support other filtering match fields and actions.
   The 'ietf-dots-data-channel' provides a method for an implementation
   to expose its filtering capabilities.  The tree structure of the
   'capabilities' is shown in Figure 10.  DOTS clients that support both
   'fragment' and 'flags' (or 'flags-bitmask' and 'flags') matching
   fields MUST NOT set these fields in the same request.

   module: ietf-dots-data-channel
       +--rw dots-data
          ...
          +--ro capabilities
             +--ro address-family*        enumeration
             +--ro forwarding-actions*    identityref
             +--ro rate-limit?            boolean
             +--ro transport-protocols*   uint8
             +--ro ipv4
             |  +--ro dscp?                 boolean
             |  +--ro ecn?                  boolean
             |  +--ro length?               boolean
             |  +--ro ttl?                  boolean
             |  +--ro protocol?             boolean
             |  +--ro ihl?                  boolean
             |  +--ro flags?                boolean
             |  +--ro offset?               boolean
             |  +--ro identification?       boolean
             |  +--ro source-prefix?        boolean
             |  +--ro destination-prefix?   boolean
             |  +--ro fragment?             boolean
             +--ro ipv6
             |  +--ro dscp?                 boolean



Boucadair & Reddy        Expires January 4, 2020               [Page 19]


Internet-Draft         DOTS Data Channel Protocol              July 2019


             |  +--ro ecn?                  boolean
             |  +--ro length?               boolean
             |  +--ro hoplimit?             boolean
             |  +--ro protocol?             boolean
             |  +--ro destination-prefix?   boolean
             |  +--ro source-prefix?        boolean
             |  +--ro flow-label?           boolean
             |  +--ro fragment?             boolean
             +--ro tcp
             |  +--ro sequence-number?          boolean
             |  +--ro acknowledgement-number?   boolean
             |  +--ro data-offset?              boolean
             |  +--ro reserved?                 boolean
             |  +--ro flags?                    boolean
             |  +--ro window-size?              boolean
             |  +--ro urgent-pointer?           boolean
             |  +--ro options?                  boolean
             |  +--ro flags-bitmask?            boolean
             |  +--ro source-port?              boolean
             |  +--ro destination-port?         boolean
             |  +--ro port-range?               boolean
             +--ro udp
             |  +--ro length?             boolean
             |  +--ro source-port?        boolean
             |  +--ro destination-port?   boolean
             |  +--ro port-range?         boolean
             +--ro icmp
                +--ro type?             boolean
                +--ro code?             boolean
                +--ro rest-of-header?   boolean

                 Figure 10: Filtering Capabilities Subtree

4.3.  YANG Module

   This module uses the common YANG types defined in [RFC6991] and types
   defined in [RFC8519].

 <CODE BEGINS> file "ietf-dots-data-channel@2019-05-09.yang"
 module ietf-dots-data-channel {
   yang-version 1.1;
   namespace "urn:ietf:params:xml:ns:yang:ietf-dots-data-channel";
   prefix data-channel;

   import ietf-inet-types {
     prefix inet;
     reference "Section 4 of RFC 6991";
   }



Boucadair & Reddy        Expires January 4, 2020               [Page 20]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   import ietf-access-control-list {
     prefix ietf-acl;
     reference
       "RFC 8519: YANG Data Model for Network Access
                  Control Lists (ACLs)";
   }
   import ietf-packet-fields {
     prefix packet-fields;
     reference
       "RFC 8519: YANG Data Model for Network Access
                  Control Lists (ACLs)";
   }

   organization
     "IETF DDoS Open Threat Signaling (DOTS) Working Group";
   contact
     "WG Web:   <https://datatracker.ietf.org/wg/dots/>
      WG List:  <mailto:dots@ietf.org>

      Editor:  Mohamed Boucadair
               <mailto:mohamed.boucadair@orange.com>

      Editor:  Konda, Tirumaleswar Reddy
               <mailto:TirumaleswarReddy_Konda@McAfee.com>

      Author:  Jon Shallow
               <mailto:jon.shallow@nccgroup.com>

      Author:  Kaname Nishizuka
               <mailto:kaname@nttv6.jp>

      Author:  Liang Xia
               <mailto:frank.xialiang@huawei.com>

      Author:  Prashanth Patil
               <mailto:praspati@cisco.com>

      Author:  Andrew Mortensen
               <mailto:amortensen@arbor.net>

      Author:  Nik Teague
               <mailto:nteague@verisign.com>";
   description
     "This module contains YANG definition for configuring
      aliases for resources and filtering rules using DOTS
      data channel.

      Copyright (c) 2019 IETF Trust and the persons identified as



Boucadair & Reddy        Expires January 4, 2020               [Page 21]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      authors of the code.  All rights reserved.

      Redistribution and use in source and binary forms, with or
      without modification, is permitted pursuant to, and subject
      to the license terms contained in, the Simplified BSD License
      set forth in Section 4.c of the IETF Trust's Legal Provisions
      Relating to IETF Documents
      (http://trustee.ietf.org/license-info).

      This version of this YANG module is part of RFC XXXX; see
      the RFC itself for full legal notices.";

   revision 2019-05-09 {
     description
       "Initial revision.";
     reference
       "RFC XXXX: Distributed Denial-of-Service Open Threat
                  Signaling (DOTS) Data Channel Specification";
   }

   typedef activation-type {
     type enumeration {
       enum "activate-when-mitigating" {
         value 1;
         description
           "The Access Control List (ACL) is installed only when
            a mitigation is active for the DOTS client.";
       }
       enum "immediate" {
         value 2;
         description
           "The ACL is immediately activated.";
       }
       enum "deactivate" {
         value 3;
         description
           "The ACL is maintained by the DOTS server, but it is
            deactivated.";
       }
     }
     description
       "Indicates the activation type of an ACL.";
   }

   typedef operator {
     type bits {
       bit not {
         position 0;



Boucadair & Reddy        Expires January 4, 2020               [Page 22]


Internet-Draft         DOTS Data Channel Protocol              July 2019


         description
           "If set, logical negation of operation.";
       }
       bit match {
         position 1;
         description
           "Match bit. This is a bitwise match operation
            defined as '(data & value) == value'.";
       }
       bit any {
         position 3;
         description
           "Any bit. This is a match on any of the bits in
            bitmask. It evaluates to 'true' if any of the bits
            in the value mask are set in the data,
            i.e., '(data & value) != 0'.";
       }
     }
     description
       "Specifies how to apply the defined bitmask.";
   }

   grouping tcp-flags {
     leaf operator {
       type operator;
       default "match";
       description
         "Specifies how to interpret the TCP flags.";
     }
     leaf bitmask {
       type uint16;
       mandatory true;
       description
         "The bitmask matches the last 4 bits of byte 12
          and byte 13 of the TCP header. For clarity, the 4 bits
          of byte 12 corresponding to the TCP data offset field
          are not included in any matching.";
     }
     description
       "Operations on TCP flags.";
   }

   typedef fragment-type {
     type bits {
       bit df {
         position 0;
         description
           "Don't fragment bit for IPv4.



Boucadair & Reddy        Expires January 4, 2020               [Page 23]


Internet-Draft         DOTS Data Channel Protocol              July 2019


            Must be set to 0 when it appears in an IPv6 filter.";
       }
       bit isf {
         position 1;
         description
           "Is a fragment.";
       }
       bit ff {
         position 2;
         description
           "First fragment.";
       }
       bit lf {
         position 3;
         description
           "Last fragment.";
       }
     }
     description
       "Different fragment types to match against.";
   }

   grouping target {
     description
       "Specifies the targets of the mitigation request.";
     leaf-list target-prefix {
       type inet:ip-prefix;
       description
         "IPv4 or IPv6 prefix identifying the target.";
     }
     list target-port-range {
       key "lower-port";
       description
         "Port range. When only lower-port is
          present, it represents a single port number.";
       leaf lower-port {
         type inet:port-number;
         mandatory true;
         description
           "Lower port number of the port range.";
       }
       leaf upper-port {
         type inet:port-number;
         must '. >= ../lower-port' {
           error-message
             "The upper port number must be greater than
              or equal to the lower-port number.";
         }



Boucadair & Reddy        Expires January 4, 2020               [Page 24]


Internet-Draft         DOTS Data Channel Protocol              July 2019


         description
           "Upper port number of the port range.";
       }
     }
     leaf-list target-protocol {
       type uint8;
       description
         "Identifies the target protocol number.

          Values are taken from the IANA protocol registry:
          https://www.iana.org/assignments/protocol-numbers/
          protocol-numbers.xhtml

          For example, 6 for TCP or 17 for UDP.";
     }
     leaf-list target-fqdn {
       type inet:domain-name;
       description
         "FQDN identifying the target.";
     }
     leaf-list target-uri {
       type inet:uri;
       description
         "URI identifying the target.";
     }
   }

   grouping fragment-fields {
     leaf operator {
       type operator;
       default "match";
       description
         "Specifies how to interpret the fragment type.";
     }
     leaf type {
       type fragment-type;
       mandatory true;
       description
         "Indicates what fragment type to look for.";
     }
     description
       "Operations on fragment types.";
   }

   grouping aliases {
     description
       "Top level container for aliases.";
     list alias {



Boucadair & Reddy        Expires January 4, 2020               [Page 25]


Internet-Draft         DOTS Data Channel Protocol              July 2019


       key "name";
       description
         "List of aliases.";
       leaf name {
         type string;
         description
           "The name of the alias.";
       }
       uses target;
       leaf pending-lifetime {
         type int32;
         units "minutes";
         config false;
         description
           "Indicates the pending validity lifetime of the alias
            entry.";
       }
     }
   }

   grouping ports {
     choice source-port {
       container source-port-range-or-operator {
         uses packet-fields:port-range-or-operator;
         description
           "Source port definition.";
       }
       description
         "Choice of specifying the source port or referring to
          a group of source port numbers.";
     }
     choice destination-port {
       container destination-port-range-or-operator {
         uses packet-fields:port-range-or-operator;
         description
           "Destination port definition.";
       }
       description
         "Choice of specifying a destination port or referring
          to a group of destination port numbers.";
     }
     description
       "Choice of specifying a source or destination port numbers.";
   }

   grouping access-lists {
     description
       "Specifies the ordered set of Access Control Lists.";



Boucadair & Reddy        Expires January 4, 2020               [Page 26]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     list acl {
       key "name";
       ordered-by user;
       description
         "An ACL is an ordered list of Access Control Entries (ACE).
          Each ACE has a list of match criteria and a list of actions.";
       leaf name {
         type string {
           length "1..64";
         }
         description
           "The name of the access list.";
         reference
           "RFC 8519: YANG Data Model for Network Access
                      Control Lists (ACLs)";
       }
       leaf type {
         type ietf-acl:acl-type;
         description
           "Type of access control list. Indicates the primary intended
            type of match criteria (e.g., IPv4, IPv6) used in the list
            instance.";
         reference
           "RFC 8519: YANG Data Model for Network Access
                      Control Lists (ACLs)";
       }
       leaf activation-type {
         type activation-type;
         default "activate-when-mitigating";
         description
           "Indicates the activation type of an ACL. An ACL can be
            deactivated, installed immediately, or installed when
            a mitigation is active.";
       }
       leaf pending-lifetime {
         type int32;
         units "minutes";
         config false;
         description
           "Indicates the pending validity lifetime of the ACL
            entry.";
       }
       container aces {
         description
           "The Access Control Entries container contains
            a list of ACEs.";
         list ace {
           key "name";



Boucadair & Reddy        Expires January 4, 2020               [Page 27]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           ordered-by user;
           description
             "List of access list entries.";
           leaf name {
             type string {
               length "1..64";
             }
             description
               "A unique name identifying this ACE.";
             reference
               "RFC 8519: YANG Data Model for Network Access
                          Control Lists (ACLs)";
           }
           container matches {
             description
               "The rules in this set determine what fields will be
                matched upon before any action is taken on them.

                If no matches are defined in a particular container,
                then any packet will match that container.

                If no matches are specified at all in an ACE, then any
                packet will match the ACE.";
             reference
               "RFC 8519: YANG Data Model for Network Access
                          Control Lists (ACLs)";
             choice l3 {
               container ipv4 {
                 when "derived-from(../../../../type, "
                    + "'ietf-acl:ipv4-acl-type')";
                 uses packet-fields:acl-ip-header-fields;
                 uses packet-fields:acl-ipv4-header-fields;
                 container fragment {
                   description
                     "Indicates how to handle IPv4 fragments.";
                   uses fragment-fields;
                 }
                 description
                   "Rule set that matches IPv4 header.";
               }
               container ipv6 {
                 when "derived-from(../../../../type, "
                    + "'ietf-acl:ipv6-acl-type')";
                 uses packet-fields:acl-ip-header-fields;
                 uses packet-fields:acl-ipv6-header-fields;
                 container fragment {
                   description
                     "Indicates how to handle IPv6 fragments.";



Boucadair & Reddy        Expires January 4, 2020               [Page 28]


Internet-Draft         DOTS Data Channel Protocol              July 2019


                   uses fragment-fields;
                 }
                 description
                   "Rule set that matches IPv6 header.";
               }
               description
                 "Either IPv4 or IPv6.";
             }
             choice l4 {
               container tcp {
                 uses packet-fields:acl-tcp-header-fields;
                 container flags-bitmask {
                   description
                     "Indicates how to handle TCP flags.";
                   uses tcp-flags;
                 }
                 uses ports;
                 description
                   "Rule set that matches TCP header.";
               }
               container udp {
                 uses packet-fields:acl-udp-header-fields;
                 uses ports;
                 description
                   "Rule set that matches UDP header.";
               }
               container icmp {
                 uses packet-fields:acl-icmp-header-fields;
                 description
                   "Rule set that matches ICMP/ICMPv6 header.";
               }
               description
                 "Can be TCP, UDP, or ICMP/ICMPv6";
             }
           }
           container actions {
             description
               "Definitions of action for this ACE.";
             leaf forwarding {
               type identityref {
                 base ietf-acl:forwarding-action;
               }
               mandatory true;
               description
                 "Specifies the forwarding action per ACE.";
               reference
                 "RFC 8519: YANG Data Model for Network Access
                            Control Lists (ACLs)";



Boucadair & Reddy        Expires January 4, 2020               [Page 29]


Internet-Draft         DOTS Data Channel Protocol              July 2019


             }
             leaf rate-limit {
               when "../forwarding = 'ietf-acl:accept'" {
                 description
                   "Rate-limit is valid only when accept action is
                    used.";
               }
               type decimal64 {
                 fraction-digits 2;
               }
               units "bytes per second";
               description
                 "Specifies how to rate-limit the traffic.";
             }
           }
           container statistics {
             config false;
             description
               "Aggregate statistics.";
             uses ietf-acl:acl-counters;
           }
         }
       }
     }
   }

   container dots-data {
     description
       "Main container for DOTS data channel.";
     list dots-client {
       key "cuid";
       description
         "List of DOTS clients.";
       leaf cuid {
         type string;
         description
           "A unique identifier that is generated by a DOTS client
            to prevent request collisions.";
         reference
           "RFC YYYY: Distributed Denial-of-Service Open Threat
                   Signaling (DOTS) Signal Channel Specification";
       }
       leaf cdid {
         type string;
         description
           "A client domain identifier conveyed by a
            server-domain DOTS gateway to a remote DOTS server.";
         reference



Boucadair & Reddy        Expires January 4, 2020               [Page 30]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           "RFC YYYY: Distributed Denial-of-Service Open Threat
                   Signaling (DOTS) Signal Channel Specification";
       }
       container aliases {
         description
           "Set of aliases that are bound to a DOTS client.";
         uses aliases;
       }
       container acls {
         description
           "Access lists that are bound to a DOTS client.";
         uses access-lists;
       }
     }
     container capabilities {
       config false;
       description
         "Match capabilities";
       leaf-list address-family {
         type enumeration {
           enum "ipv4" {
             description
               "IPv4 is supported.";
           }
           enum "ipv6" {
             description
               "IPv6 is supported.";
           }
         }
         description
           "Indicates the IP address families supported by
            the DOTS server.";
       }
       leaf-list forwarding-actions {
         type identityref {
           base ietf-acl:forwarding-action;
         }
         description
           "Supported forwarding action(s).";
       }
       leaf rate-limit {
         type boolean;
         description
           "Support of rate-limit action.";
       }
       leaf-list transport-protocols {
         type uint8;
         description



Boucadair & Reddy        Expires January 4, 2020               [Page 31]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           "Upper-layer protocol associated with a filtering rule.

            Values are taken from the IANA protocol registry:
            https://www.iana.org/assignments/protocol-numbers/
            protocol-numbers.xhtml

            For example, this field contains 1 for ICMP, 6 for TCP
            17 for UDP, or 58 for ICMPv6.";
       }
       container ipv4 {
         description
           "Indicates IPv4 header fields that are supported to enforce
            ACLs.";
         leaf dscp {
           type boolean;
           description
             "Support of filtering based on Differentiated Services Code
              Point (DSCP).";
         }
         leaf ecn {
           type boolean;
           description
             "Support of filtering based on Explicit Congestion
              Notification (ECN).";
         }
         leaf length {
           type boolean;
           description
             "Support of filtering based on the Total Length.";
         }
         leaf ttl {
           type boolean;
           description
             "Support of filtering based on the Time to Live (TTL).";
         }
         leaf protocol {
           type boolean;
           description
             "Support of filtering based on protocol field.";
         }
         leaf ihl {
           type boolean;
           description
             "Support of filtering based on the Internet Header
              Length (IHL).";
         }
         leaf flags {
           type boolean;



Boucadair & Reddy        Expires January 4, 2020               [Page 32]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           description
             "Support of filtering based on the 'flags'.";
         }
         leaf offset {
           type boolean;
           description
             "Support of filtering based on the 'offset'.";
         }
         leaf identification {
           type boolean;
           description
             "Support of filtering based on the 'identification'.";
         }
         leaf source-prefix {
           type boolean;
           description
             "Support of filtering based on the source prefix.";
         }
         leaf destination-prefix {
           type boolean;
           description
             "Support of filtering based on the destination prefix.";
         }
         leaf fragment {
           type boolean;
           description
             "Indicates the capability of a DOTS server to
              enforce filters on IPv4 fragments. That is, the match
              functionality based on the Layer 3 'fragment' clause
              is supported.";
         }
       }
       container ipv6 {
         description
           "Indicates IPv6 header fields that are supported to enforce
            ACLs.";
         leaf dscp {
           type boolean;
           description
             "Support of filtering based on DSCP.";
         }
         leaf ecn {
           type boolean;
           description
             "Support of filtering based on ECN.";
         }
         leaf length {
           type boolean;



Boucadair & Reddy        Expires January 4, 2020               [Page 33]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           description
             "Support of filtering based on the Payload Length.";
         }
         leaf hoplimit {
           type boolean;
           description
             "Support of filtering based on the Hop Limit.";
         }
         leaf protocol {
           type boolean;
           description
             "Support of filtering based on the Next Header field.";
         }
         leaf destination-prefix {
           type boolean;
           description
             "Support of filtering based on the destination prefix.";
         }
         leaf source-prefix {
           type boolean;
           description
             "Support of filtering based on the source prefix.";
         }
         leaf flow-label {
           type boolean;
           description
             "Support of filtering based on the Flow label.";
         }
         leaf fragment {
           type boolean;
           description
             "Indicates the capability of a DOTS server to
              enforce filters on IPv6 fragments.";
         }
       }
       container tcp {
         description
           "Set of TCP fields that are supported by the DOTS server
            to enforce filters.";
         leaf sequence-number {
           type boolean;
           description
             "Support of filtering based on the TCP sequence number.";
         }
         leaf acknowledgement-number {
           type boolean;
           description
             "Support of filtering based on the TCP acknowledgement



Boucadair & Reddy        Expires January 4, 2020               [Page 34]


Internet-Draft         DOTS Data Channel Protocol              July 2019


              number.";
         }
         leaf data-offset {
           type boolean;
           description
             "Support of filtering based on the TCP data-offset.";
         }
         leaf reserved {
           type boolean;
           description
             "Support of filtering based on the TCP reserved field.";
         }
         leaf flags {
           type boolean;
           description
             "Support of filtering, as defined in RFC 8519, based
              on the TCP flags.";
         }
         leaf window-size {
           type boolean;
           description
             "Support of filtering based on the TCP window size.";
         }
         leaf urgent-pointer {
           type boolean;
           description
             "Support of filtering based on the TCP urgent pointer.";
         }
         leaf options {
           type boolean;
           description
             "Support of filtering based on the TCP options.";
         }
         leaf flags-bitmask {
           type boolean;
           description
             "Support of filtering based on the TCP flags bitmask.";
         }
         leaf source-port {
           type boolean;
           description
             "Support of filtering based on the source port number.";
         }
         leaf destination-port {
           type boolean;
           description
             "Support of filtering based on the destination port
              number.";



Boucadair & Reddy        Expires January 4, 2020               [Page 35]


Internet-Draft         DOTS Data Channel Protocol              July 2019


         }
         leaf port-range {
           type boolean;
           description
             "Support of filtering based on a port range.

              This includes filtering based on a source port range,
              destination port range, or both. All operators
              (i.e, less than or equal to, greater than or equal to,
              equal to, and not equal to) are supported.";
         }
       }
       container udp {
         description
           "Set of UDP fields that are supported by the DOTS server
            to enforce filters.";
         leaf length {
           type boolean;
           description
             "Support of filtering based on the UDP length.";
         }
         leaf source-port {
           type boolean;
           description
             "Support of filtering based on the source port number.";
         }
         leaf destination-port {
           type boolean;
           description
             "Support of filtering based on the destination port
              number.";
         }
         leaf port-range {
           type boolean;
           description
             "Support of filtering based on a port range.

              This includes filtering based on a source port range,
              destination port range, or both. All operators
              (i.e, less than or equal, greater than or equal, equal to,
              and not equal to) are supported.";
         }
       }
       container icmp {
         description
           "Set of ICMP/ICMPv6 fields that are supported by the DOTS
            server to enforce filters.";
         leaf type {



Boucadair & Reddy        Expires January 4, 2020               [Page 36]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           type boolean;
           description
             "Support of filtering based on the ICMP/ICMPv6 type.";
         }
         leaf code {
           type boolean;
           description
             "Support of filtering based on the ICMP/ICMPv6 code.";
         }
         leaf rest-of-header {
           type boolean;
           description
             "Support of filtering based on the ICMP four-bytes
              field / the ICMPv6 message body.";
         }
       }
     }
   }
 }
 <CODE ENDS>

5.  Managing DOTS Clients

5.1.  Registering DOTS Clients

   In order to make use of DOTS data channel, a DOTS client MUST
   register to its DOTS server(s) by creating a DOTS client ('dots-
   client') resource.  To that aim, DOTS clients SHOULD send a POST
   request (shown in Figure 11).

    POST /restconf/data/ietf-dots-data-channel:dots-data HTTP/1.1
    Host: {host}:{port}
    Content-Type: application/yang-data+json

    {
      "ietf-dots-data-channel:dots-client": [
        {
          "cuid": "string"
        }
      ]
    }

                    Figure 11: POST to Register Schema

   The 'cuid' (client unique identifier) parameter is described below:

   cuid:  A globally unique identifier that is meant to prevent
      collisions among DOTS clients.  This attribute has the same



Boucadair & Reddy        Expires January 4, 2020               [Page 37]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      meaning, syntax, and processing rules as the 'cuid' attribute
      defined in [I-D.ietf-dots-signal-channel].

      DOTS clients MUST use the same 'cuid' for both signal and data
      channels.

      This is a mandatory attribute.

   In deployments where server-domain DOTS gateways are enabled,
   identity information about the origin source client domain SHOULD be
   supplied to the DOTS server.  That information is meant to assist the
   DOTS server to enforce some policies.  These policies can be enforced
   per-client, per-client domain, or both.  Figure 12 shows a schema
   example of a request relayed by a server-domain DOTS gateway.

    POST /restconf/data/ietf-dots-data-channel:dots-data HTTP/1.1
    Host: {host}:{port}
    Content-Type: application/yang-data+json

    {
      "ietf-dots-data-channel:dots-client": [
        {
          "cuid": "string",
          "cdid": "string"
        }
      ]
    }

   Figure 12: POST to Register Schema (via a Server-Domain DOTS Gateway)

   A server-domain DOTS gateway SHOULD add the following attribute:

   cdid:  This attribute has the same meaning, syntax, and processing
      rules as the 'cdid' attribute defined in
      [I-D.ietf-dots-signal-channel].

      In deployments where server-domain DOTS gateways are enabled,
      'cdid' does not need to be inserted when relaying DOTS methods to
      manage aliases (Section 6) or filtering rules (Section 7).  DOTS
      servers are responsible for maintaining the association between
      'cdid' and 'cuid' for policy enforcement purposes.

      This is an optional attribute.

   A request example to create a 'dots-client' resource is depicted in
   Figure 13.  This request is relayed by a server-domain DOTS gateway
   as hinted by the presence of the 'cdid' attribute.




Boucadair & Reddy        Expires January 4, 2020               [Page 38]


Internet-Draft         DOTS Data Channel Protocol              July 2019


    POST /restconf/data/ietf-dots-data-channel:dots-data HTTP/1.1
    Host: example.com
    Content-Type: application/yang-data+json

    {
      "ietf-dots-data-channel:dots-client": [
        {
          "cuid": "dz6pHjaADkaFTbjr0JGBpw",
          "cdid": "7eeaf349529eb55ed50113"
        }
      ]
    }

                Figure 13: POST to Register (DOTS gateway)

   As a reminder, DOTS gateways may rewrite the 'cuid' used by peer DOTS
   clients (Section 4.4.1 of [I-D.ietf-dots-signal-channel]).

   DOTS servers can identify the DOTS client domain using the 'cdid'
   parameter or using the client's DNS name specified in the Subject
   Alternative Name extension's dNSName type in the client certificate
   [RFC6125].

   DOTS servers MUST limit the number of 'dots-client' resources to be
   created by the same DOTS client to 1 per request.  Requests with
   multiple 'dots-client' resources MUST be rejected by DOTS servers.
   To that aim, the DOTS server MUST rely on the same procedure to
   unambiguously identify a DOTS client as discussed in Section 4.4.1 of
   [I-D.ietf-dots-signal-channel].

   The DOTS server indicates the result of processing the POST request
   using status-line codes.  Status codes in the range "2xx" codes are
   success, "4xx" codes are some sort of invalid requests and "5xx"
   codes are returned if the DOTS server has erred or is incapable of
   accepting the creation of the 'dots-client' resource.  In particular,

   o  "201 Created" status-line is returned in the response, if the DOTS
      server has accepted the request.

   o  "400 Bad Request" status-line is returned by the DOTS server, if
      the request does not include a 'cuid' parameter.  The error-tag
      "missing-attribute" is used in this case.

   o  "409 Conflict" status-line is returned to the requesting DOTS
      client, if the data resource already exists.  The error-tag
      "resource-denied" is used in this case.





Boucadair & Reddy        Expires January 4, 2020               [Page 39]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   Once a DOTS client registers itself to a DOTS server, it can
   create/delete/retrieve aliases (Section 6) and filtering rules
   (Section 7).

   A DOTS client MAY use the PUT request (Section 4.5 in [RFC8040]) to
   register a DOTS client within the DOTS server.  An example is shown
   in Figure 14.

            PUT /restconf/data/ietf-dots-data-channel:dots-data\
                /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
            Host: example.com
            Content-Type: application/yang-data+json

            {
              "ietf-dots-data-channel:dots-client": [
                {
                  "cuid": "dz6pHjaADkaFTbjr0JGBpw"
                }
              ]
            }

                        Figure 14: PUT to Register

   The DOTS gateway that inserted a 'cdid' in a PUT request MUST strip
   the 'cdid' parameter in the corresponding response before forwarding
   the response to the DOTS client.

5.2.  Unregistering DOTS Clients

   A DOTS client de-registers from its DOTS server(s) by deleting the
   'cuid' resource(s).  Resources bound to this DOTS client will be
   deleted by the DOTS server.  An example of a de-register request is
   shown in Figure 15.

    DELETE /restconf/data/ietf-dots-data-channel:dots-data\
           /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
    Host: example.com

                   Figure 15: De-register a DOTS Client

6.  Managing DOTS Aliases

   The following sub-sections define means for a DOTS client to create
   aliases (Section 6.1), retrieve one or a list of aliases
   (Section 6.2), and delete an alias (Section 6.3).






Boucadair & Reddy        Expires January 4, 2020               [Page 40]


Internet-Draft         DOTS Data Channel Protocol              July 2019


6.1.  Create Aliases

   A POST or PUT request is used by a DOTS client to create aliases, for
   resources for which a mitigation may be requested.  Such aliases may
   be used in subsequent DOTS signal channel exchanges to refer more
   efficiently to the resources under attack.

   DOTS clients within the same domain can create different aliases for
   the same resource.

   The structure of POST requests used to create aliases is shown in
   Figure 16.

    POST /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=cuid HTTP/1.1
    Host: {host}:{port}
    Content-Type: application/yang-data+json

    {
     "ietf-dots-data-channel:aliases": {
       "alias": [
         {
           "name": "string",
           "target-prefix": [
             "string"
           ],
           "target-port-range": [
             {
               "lower-port": integer,
               "upper-port": integer
             }
           ],
           "target-protocol": [
             integer
           ],
           "target-fqdn": [
             "string"
           ],
           "target-uri": [
             "string"
           ]
         }
       ]
     }
   }

            Figure 16: POST to Create Aliases (Request Schema)




Boucadair & Reddy        Expires January 4, 2020               [Page 41]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   The parameters are described below:

   name:  Name of the alias.

      This is a mandatory attribute.

   target-prefix:   Prefixes are separated by commas.  Prefixes are
      represented using Classless Inter-domain Routing (CIDR) notation
      [RFC4632].  As a reminder, the prefix length must be less than or
      equal to 32 (resp. 128) for IPv4 (resp.  IPv6).

      The prefix list MUST NOT include broadcast, loopback, or multicast
      addresses.  These addresses are considered as invalid values.  In
      addition, the DOTS server MUST validate that these prefixes are
      within the scope of the DOTS client domain.  Other validation
      checks may be supported by DOTS servers.

      This is an optional attribute.

   target-port-range:   A range of port numbers.

      The port range is defined by two bounds, a lower port number
      (lower-port) and an upper port number (upper-port).  The range is
      considered to include both the lower and upper bounds.

      When only 'lower-port' is present, it represents a single port
      number.

      For TCP, UDP, Stream Control Transmission Protocol (SCTP)
      [RFC4960], or Datagram Congestion Control Protocol (DCCP)
      [RFC4340], the range of port numbers can be, for example,
      1024-65535.

      This is an optional attribute.

   target-protocol:   A list of protocols.  Values are taken from the
      IANA protocol registry [proto_numbers].

      If 'target-protocol' is not specified, then the request applies to
      any protocol.

      This is an optional attribute.

   target-fqdn:   A list of Fully Qualified Domain Names (FQDNs)
      identifying resources under attack [RFC8499].

      How a name is passed to an underlying name resolution library is
      implementation- and deployment-specific.  Nevertheless, once the



Boucadair & Reddy        Expires January 4, 2020               [Page 42]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      name is resolved into one or multiple IP addresses, DOTS servers
      MUST apply the same validation checks as those for 'target-
      prefix'.

      The use of FQDNs may be suboptimal because it does not guarantee
      that the DOTS server will resolve a name to the same IP addresses
      that the DOTS client does.

      This is an optional attribute.

   target-uri:   A list of Uniform Resource Identifiers (URIs)
      [RFC3986].

      The same validation checks used for 'target-fqdn' MUST be followed
      by DOTS servers to validate a target URI.

      This is an optional attribute.

   In POST or PUT requests, at least one of the 'target-prefix',
   'target-fqdn', or 'target-uri' attributes MUST be present.  DOTS
   agents can safely ignore Vendor-Specific parameters they don't
   understand.

   If more than one 'target-*' scope types (e.g., 'target-prefix' and
   'target-fqdn' or 'target-fqdn' and 'target-uri') are included in a
   POST or PUT request, the DOTS server binds all resulting IP
   addresses/prefixes to the same resource.

   Figure 17 shows a POST request to create an alias called "https1" for
   HTTPS servers with IP addresses 2001:db8:6401::1 and 2001:db8:6401::2
   listening on TCP port number 443.




















Boucadair & Reddy        Expires January 4, 2020               [Page 43]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   POST /restconf/data/ietf-dots-data-channel:dots-data\
        /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
   Host: www.example.com
   Content-Type: application/yang-data+json

   {
     "ietf-dots-data-channel:aliases": {
       "alias": [
         {
           "name": "https1",
           "target-protocol": [
             6
           ],
           "target-prefix": [
             "2001:db8:6401::1/128",
             "2001:db8:6401::2/128"
           ],
           "target-port-range": [
             {
               "lower-port": 443
             }
           ]
         }
       ]
     }
   }

              Figure 17: Example of a POST to Create an Alias

   "201 Created" status-line MUST be returned in the response if the
   DOTS server has accepted the alias.

   "409 Conflict" status-line MUST be returned to the requesting DOTS
   client, if the request is conflicting with an existing alias name.
   The error-tag "resource-denied" is used in this case.

   If the request is missing a mandatory attribute or it contains an
   invalid or unknown parameter, "400 Bad Request" status-line MUST be
   returned by the DOTS server.  The error-tag is set to "missing-
   attribute", "invalid-value", or "unknown-element" as a function of
   the encountered error.

   If the request is received via a server-domain DOTS gateway, but the
   DOTS server does not maintain a 'cdid' for this 'cuid' while a 'cdid'
   is expected to be supplied, the DOTS server MUST reply with "403
   Forbidden" status-line and the error-tag "access-denied".  Upon
   receipt of this message, the DOTS client MUST register (Section 5).




Boucadair & Reddy        Expires January 4, 2020               [Page 44]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   A DOTS client uses the PUT request to modify the aliases in the DOTS
   server.  In particular, a DOTS client MUST update its alias entries
   upon change of the prefix indicated in the 'target-prefix'.

   A DOTS server MUST maintain an alias for at least 10080 minutes (1
   week).  If no refresh request is seen from the DOTS client, the DOTS
   server removes expired entries.

6.2.  Retrieve Installed Aliases

   A GET request is used to retrieve one or all installed aliases by a
   DOTS client from a DOTS server (Section 3.3.1 in [RFC8040]).  If no
   'name' is included in the request, this is an indication that the
   request is about retrieving all aliases instantiated by the DOTS
   client.

   Figure 18 shows an example to retrieve all the aliases that were
   instantiated by the requesting DOTS client.  The "content" query
   parameter and its permitted values are defined in Section 4.8.1 of
   [RFC8040].

     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw\
         /aliases?content=all HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

             Figure 18: GET to Retrieve All Installed Aliases

   Figure 19 shows an example of the response message body that includes
   all the aliases that are maintained by the DOTS server for the DOTS
   client identified by the 'cuid' parameter.



















Boucadair & Reddy        Expires January 4, 2020               [Page 45]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   {
     "ietf-dots-data-channel:aliases": {
       "alias": [
         {
           "name": "Server1",
           "target-protocol": [
             6
           ],
           "target-prefix": [
             "2001:db8:6401::1/128",
             "2001:db8:6401::2/128"
           ],
           "target-port-range": [
             {
               "lower-port": 443
             }
           ],
           "pending-lifetime": 3596
         },
         {
           "name": "Server2",
           "target-protocol": [
             6
           ],
           "target-prefix": [
             "2001:db8:6401::10/128",
             "2001:db8:6401::20/128"
           ],
           "target-port-range": [
             {
               "lower-port": 80
             }
           ],
           "pending-lifetime": 9869
         }
       ]
     }
   }

   Figure 19: An Example of Response Body Listing All Installed Aliases

   Figure 20 shows an example of a GET request to retrieve the alias
   "Server2" that was instantiated by the DOTS client.








Boucadair & Reddy        Expires January 4, 2020               [Page 46]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw\
         /aliases/alias=Server2?content=all HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

                    Figure 20: GET to Retrieve an Alias

   If an alias name ('name') is included in the request, but the DOTS
   server does not find that alias name for this DOTS client in its
   configuration data, it MUST respond with a "404 Not Found" status-
   line.

6.3.  Delete Aliases

   A DELETE request is used to delete an alias maintained by a DOTS
   server.

   If the DOTS server does not find the alias name, conveyed in the
   DELETE request, in its configuration data for this DOTS client, it
   MUST respond with a "404 Not Found" status-line.

   The DOTS server successfully acknowledges a DOTS client's request to
   remove the alias using "204 No Content" status-line in the response.

   Figure 21 shows an example of a request to delete an alias.

     DELETE /restconf/data/ietf-dots-data-channel:dots-data\
            /dots-client=dz6pHjaADkaFTbjr0JGBpw\
            /aliases/alias=Server1 HTTP/1.1
     Host: example.com

                        Figure 21: Delete an Alias

7.  Managing DOTS Filtering Rules

   The following sub-sections define means for a DOTS client to retrieve
   DOTS filtering capabilities (Section 7.1), create filtering rules
   (Section 7.2), retrieve active filtering rules (Section 7.3), and
   delete a filtering rule (Section 7.4).

7.1.  Retrieve DOTS Filtering Capabilities

   A DOTS client MAY send a GET request to retrieve the filtering
   capabilities supported by a DOTS server.  Figure 22 shows an example
   of such request.





Boucadair & Reddy        Expires January 4, 2020               [Page 47]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /capabilities HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

       Figure 22: GET to Retrieve the Capabilities of a DOTS Server

   A DOTS client which issued a GET request to retrieve the filtering
   capabilities supported by its DOTS server, SHOULD NOT request for
   filtering actions that are not supported by that DOTS server.

   Figure 23 shows an example of a response body received from a DOTS
   server which supports:

   o  IPv4, IPv6, TCP, UDP, ICMP, and ICMPv6 mandatory match criteria
      listed in Section 4.2.

   o  'accept', 'drop', and 'rate-limit' actions.

































Boucadair & Reddy        Expires January 4, 2020               [Page 48]


Internet-Draft         DOTS Data Channel Protocol              July 2019


    {
     "ietf-dots-data-channel:capabilities": {
       "address-family": ["ipv4", "ipv6"],
       "forwarding-actions": ["drop", "accept"],
       "rate-limit": true,
       "transport-protocols": [1, 6, 17, 58],
       "ipv4": {
         "length": true,
         "protocol": true,
         "destination-prefix": true,
         "source-prefix": true,
         "fragment": true
       },
       "ipv6": {
         "length": true,
         "protocol": true,
         "destination-prefix": true,
         "source-prefix": true,
         "fragment": true
       },
       "tcp": {
         "flags-bitmask": true,
         "source-port": true,
         "destination-port": true,
         "port-range": true
       },
       "udp": {
         "length": true,
         "source-port": true,
         "destination-port": true,
         "port-range": true
       },
       "icmp": {
         "type": true,
         "code": true
       }
     }
   }

       Figure 23: Reply to a GET Request with Filtering Capabilities
                              (Message Body)

7.2.  Install Filtering Rules

   A POST or PUT request is used by a DOTS client to communicate
   filtering rules to a DOTS server.





Boucadair & Reddy        Expires January 4, 2020               [Page 49]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   Figure 24 shows a POST request example to block traffic from
   192.0.2.0/24 and destined to 198.51.100.0/24.  Other examples are
   discussed in Appendix A.

    POST /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
    Host: example.com
    Content-Type: application/yang-data+json

    {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "sample-ipv4-acl",
           "type": "ipv4-acl-type",
           "activation-type": "activate-when-mitigating",
           "aces": {
             "ace": [
               {
                 "name": "rule1",
                 "matches": {
                   "ipv4": {
                     "destination-ipv4-network": "198.51.100.0/24",
                     "source-ipv4-network": "192.0.2.0/24"
                   }
                 },
                 "actions": {
                   "forwarding": "drop"
                 }
               }
             ]
           }
         }
       ]
     }
    }

                Figure 24: POST to Install Filtering Rules

   The meaning of these parameters is as follows:

   name:  The name of the access list.

      This is a mandatory attribute.

   type:  Indicates the primary intended type of match criteria (e.g.,
      IPv4, IPv6).  It is set to 'ipv4-acl-type' in the example of
      Figure 24.



Boucadair & Reddy        Expires January 4, 2020               [Page 50]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      This is an optional attribute.

   activation-type:  Indicates whether an ACL has to be activated
      (immediately or during mitigation time) or instantiated without
      being activated (deactivated).  Deactivated ACLs can be activated
      using a variety of means such as manual configuration on a DOTS
      server or using the DOTS data channel.

      If this attribute is not provided, the DOTS server MUST use
      'activate-when-mitigating' as default value.

      When a mitigation is in progress, the DOTS server MUST only
      activate 'activate-when-mitigating' filters that are bound to the
      DOTS client that triggered the mitigation.

      This is an optional attribute.

   matches:  Define criteria used to identify a flow on which to apply
      the rule.  It can be "l3" (IPv4, IPv6) or "l4" (TCP, UDP, ..).
      The detailed match parameters are specified in Section 4.

      In the example depicted in Figure 24, an IPv4 matching criteria is
      used.

      This is an optional attribute.

   destination-ipv4-network:  The destination IPv4 prefix.  DOTS servers
      MUST validate that these prefixes are within the scope of the DOTS
      client domain.  Other validation checks may be supported by DOTS
      servers.  If this attribute is not provided, the DOTS server
      enforces the ACL on any destination IP address that belong to the
      DOTS client domain.

      This is a mandatory attribute in requests with an 'activation-
      type' set to 'immediate'.

   source-ipv4-network:  The source IPv4 prefix.

      This is an optional attribute.

   actions:   Actions in the forwarding ACL category can be "drop" or
      "accept".  The "accept" action is used to accept-list traffic.
      The "drop" action is used to drop-list traffic.

      Accepted traffic may be subject to "rate-limit"; the allowed
      traffic rate is represented in bytes per second.  This unit is the
      same as the one used for "traffic-rate" in [RFC5575].




Boucadair & Reddy        Expires January 4, 2020               [Page 51]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      This is a mandatory attribute.

   The DOTS server indicates the result of processing the POST request
   using the status-line.  Concretely, "201 Created" status-line MUST be
   returned in the response if the DOTS server has accepted the
   filtering rules.  If the request is missing a mandatory attribute or
   contains an invalid or unknown parameter (e.g., a match field not
   supported by the DOTS server), "400 Bad Request" status-line MUST be
   returned by the DOTS server in the response.  The error-tag is set to
   "missing-attribute", "invalid-value", or "unknown-element" as a
   function of the encountered error.

   If the request is received via a server-domain DOTS gateway, but the
   DOTS server does not maintain a 'cdid' for this 'cuid' while a 'cdid'
   is expected to be supplied, the DOTS server MUST reply with "403
   Forbidden" status-line and the error-tag "access-denied".  Upon
   receipt of this message, the DOTS client MUST register (Figure 11).

   If the request is conflicting with an existing filtering installed by
   another DOTS client of the domain, absent any local policy, the DOTS
   server returns "409 Conflict" status-line to the requesting DOTS
   client.  The error-tag "resource-denied" is used in this case.

   The "insert" query parameter (Section 4.8.5 of [RFC8040]) MAY be used
   to specify how an access control entry is inserted within an ACL and
   how an ACL is inserted within an ACL set.

   The DOTS client uses the PUT request to modify its filtering rules
   maintained by the DOTS server.  In particular, a DOTS client MUST
   update its filtering entries upon change of the destination-prefix.
   How such change is detected is out of scope.

   A DOTS server MUST maintain a filtering rule for at least 10080
   minutes (1 week).  If no refresh request is seen from the DOTS
   client, the DOTS server removes expired entries.  Typically, a
   refresh request is a PUT request which echoes the content of a
   response to a GET request with all of the read-only parameters
   stripped out (e.g., pending-lifetime).

7.3.  Retrieve Installed Filtering Rules

   A DOTS client periodically queries its DOTS server to check the
   counters for installed filtering rules.  A GET request is used to
   retrieve filtering rules from a DOTS server.  In order to indicate
   which type of data is requested in a GET request, the DOTS client
   sets adequately the "content" query parameter.





Boucadair & Reddy        Expires January 4, 2020               [Page 52]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   If the DOTS server does not find the access list name conveyed in the
   GET request in its configuration data for this DOTS client, it
   responds with a "404 Not Found" status-line.

   In order to illustrate the intended behavior, consider the example
   depicted in Figure 25.  In reference to this example, the DOTS client
   requests the creation of an immediate ACL called "test-acl-ipv6-udp".












































Boucadair & Reddy        Expires January 4, 2020               [Page 53]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   PUT /restconf/data/ietf-dots-data-channel:dots-data\
       /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
       /acl=test-acl-ipv6-udp HTTP/1.1
   Host: example.com
   Content-Type: application/yang-data+json

   {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "test-acl-ipv6-udp",
           "type": "ipv6-acl-type",
           "activation-type": "immediate",
           "aces": {
             "ace": [
               {
                 "name": "my-test-ace",
                 "matches": {
                   "ipv6": {
                     "destination-ipv6-network": "2001:db8:6401::2/127",
                     "source-ipv6-network": "2001:db8:1234::/96",
                     "protocol": 17,
                     "flow-label": 10000
                   },
                   "udp": {
                     "source-port": {
                       "operator": "lte",
                       "port": 80
                     },
                     "destination-port": {
                       "operator": "neq",
                       "port": 1010
                     }
                   }
                 },
                 "actions": {
                   "forwarding": "accept"
                 }
               }
             ]
           }
         }
       ]
     }
   }

         Figure 25: Example of a PUT Request to Create a Filtering




Boucadair & Reddy        Expires January 4, 2020               [Page 54]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   The peer DOTS server follows the procedure specified in Section 7.2
   to process the request.  We consider in the following that a positive
   response is sent back to the requesting DOTS client to confirm that
   the "test-acl-ipv6-udp" ACL is successfully installed by the DOTS
   server.

   The DOTS client can issue a GET request to retrieve all its filtering
   rules and the number of matches for the installed filtering rules as
   illustrated in Figure 26.  The "content" query parameter is set to
   'all'.  The message body of the response to this GET request is shown
   in Figure 27.

     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw\
         /acls?content=all HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

     Figure 26: Retrieve the Configuration Data and State Data for the
                       Filtering Rules (GET Request)































Boucadair & Reddy        Expires January 4, 2020               [Page 55]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "test-acl-ipv6-udp",
           "type": "ipv6-acl-type",
           "activation-type": "immediate",
           "pending-lifetime":9080,
           "aces": {
             "ace": [
               {
                 "name": "my-test-ace",
                 "matches": {
                   "ipv6": {
                     "destination-ipv6-network": "2001:db8:6401::2/127",
                     "source-ipv6-network": "2001:db8:1234::/96",
                     "protocol": 17,
                     "flow-label": 10000
                   },
                   "udp": {
                     "source-port": {
                       "operator": "lte",
                       "port": 80
                     },
                     "destination-port": {
                       "operator": "neq",
                       "port": 1010
                     }
                   }
                 },
                 "actions": {
                   "forwarding": "accept"
                 }
               }
             ]
           }
         }
       ]
     }
   }

     Figure 27: Retrieve the Configuration Data and State Data for the
                  Filtering Rules (Response Message Body)

   Also, a DOTS client can issue a GET request to retrieve only
   configuration data related to an ACL as shown in Figure 28.  It does
   so by setting the "content" query parameter to 'config'.




Boucadair & Reddy        Expires January 4, 2020               [Page 56]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
         /acl=test-acl-ipv6-udp?content=config HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

   Figure 28: Retrieve the Configuration Data for a Filtering Rule (GET
                                 Request)

   A response to this GET request is shown in Figure 29.









































Boucadair & Reddy        Expires January 4, 2020               [Page 57]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "test-acl-ipv6-udp",
           "type": "ipv6-acl-type",
           "activation-type": "immediate",
           "aces": {
             "ace": [
               {
                 "name": "my-test-ace",
                 "matches": {
                   "ipv6": {
                     "destination-ipv6-network": "2001:db8:6401::2/127",
                     "source-ipv6-network": "2001:db8:1234::/96",
                     "protocol": 17,
                     "flow-label": 10000
                   },
                   "udp": {
                     "source-port": {
                       "operator": "lte",
                       "port": 80
                     },
                     "destination-port": {
                       "operator": "neq",
                       "port": 1010
                     }
                   }
                 },
                 "actions": {
                   "forwarding": "accept"
                 }
               }
             ]
           }
         }
       ]
     }
   }

      Figure 29: Retrieve the Configuration Data for a Filtering Rule
                          (Response Message Body)

   A DOTS client can also issue a GET request with a "content" query
   parameter set to 'non-config' to exclusively retrieve non-
   configuration data bound to a given ACL as shown in Figure 30.  A
   response to this GET request is shown in Figure 31.




Boucadair & Reddy        Expires January 4, 2020               [Page 58]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     GET /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
         /acl=test-acl-ipv6-udp?content=non-config HTTP/1.1
     Host: example.com
     Accept: application/yang-data+json

    Figure 30: Retrieve the Non-Configuration Data for a Filtering Rule
                               (GET Request)

   {
     "ietf-dots-data-channel:acls":  {
       "acl": [
         {
           "name": "test-acl-ipv6-udp",
           "pending-lifetime": 8000,
           "aces": {
             "ace": [
               {
                 "name": "my-test-ace"
               }
             ]
           }
         }
       ]
     }
   }

    Figure 31: Retrieve the Non-Configuration Data for a Filtering Rule
                          (Response Message Body)

7.4.  Remove Filtering Rules

   A DELETE request is used by a DOTS client to delete filtering rules
   from a DOTS server.

   If the DOTS server does not find the access list name carried in the
   DELETE request in its configuration data for this DOTS client, it
   MUST respond with a "404 Not Found" status-line.  The DOTS server
   successfully acknowledges a DOTS client's request to withdraw the
   filtering rules using "204 No Content" status-line, and removes the
   filtering rules accordingly.

   Figure 32 shows an example of a request to remove the IPv4 ACL
   "sample-ipv4-acl" created in Section 7.2.







Boucadair & Reddy        Expires January 4, 2020               [Page 59]


Internet-Draft         DOTS Data Channel Protocol              July 2019


     DELETE  /restconf/data/ietf-dots-data-channel:dots-data\
             /dots-client=dz6pHjaADkaFTbjr0JGBpw/acls\
             /acl=sample-ipv4-acl HTTP/1.1
     Host: example.com

            Figure 32: Remove a Filtering Rule (DELETE Request)

   Figure 33 shows an example of a response received from the DOTS
   server to confirm the deletion of "sample-ipv4-acl".

    HTTP/1.1 204 No Content
    Server: Apache
    Date: Fri, 27 Jul 2018 10:05:15 GMT
    Cache-Control: no-cache
    Content-Type: application/yang-data+json
    Content-Length: 0
    Connection: Keep-Alive

               Figure 33: Remove a Filtering Rule (Response)

8.  Operational Considerations

   The following operational considerations should be taken into
   account:

   o  DOTS servers MUST NOT enable both DOTS data channel and direct
      configuration, to avoid race conditions and inconsistent
      configurations arising from simultaneous updates from multiple
      sources.

   o  DOTS agents SHOULD enable the DOTS data channel to configure
      aliases and ACLs, and only use direct configuration as a stop-gap
      mechanism to test DOTS signal channel with aliases and ACLs.
      Further, direct configuration SHOULD only be used when the on-path
      DOTS agents are within the same domain.

   o  If a DOTS server has enabled direct configuration, it can reject
      the DOTS data channel connection using hard ICMP error [RFC1122]
      or RST (Reset) bit in the TCP header or reject the RESTCONF
      request using an error response containing a "503 Service
      Unavailable" status-line.

9.  IANA Considerations

   This document requests IANA to register the following URI in the "ns"
   subregistry within the "IETF XML Registry" [RFC3688]:





Boucadair & Reddy        Expires January 4, 2020               [Page 60]


Internet-Draft         DOTS Data Channel Protocol              July 2019


            URI: urn:ietf:params:xml:ns:yang:ietf-dots-data-channel
            Registrant Contact: The IESG.
            XML: N/A; the requested URI is an XML namespace.

   This document requests IANA to register the following YANG module in
   the "YANG Module Names" subregistry [RFC7950] within the "YANG
   Parameters" registry.

           Name: ietf-dots-data-channel
           Namespace: urn:ietf:params:xml:ns:yang:ietf-dots-data-channel
           Prefix: data-channel
           Reference: RFC XXXX

   This module is not maintained by IANA.

10.  Security Considerations

   RESTCONF security considerations are discussed in [RFC8040].  In
   particular, DOTS agents MUST follow the security recommendations in
   Sections 2 and 12 of [RFC8040].  Also, DOTS agents MUST support the
   mutual authentication TLS profile discussed in Sections 7.1 and 8 of
   [I-D.ietf-dots-signal-channel].

   Authenticated encryption MUST be used for data confidentiality and
   message integrity.  The interaction between the DOTS agents requires
   Transport Layer Security (TLS) with a cipher suite offering
   confidentiality protection and the guidance given in [RFC7525] MUST
   be followed to avoid attacks on TLS.

   The installation of drop- or accept-list rules using RESTCONF over
   TLS reveals the attacker IP addresses and legitimate IP addresses
   only to the DOTS server trusted by the DOTS client.  The secure
   communication channel between DOTS agents provides privacy and
   prevents a network eavesdropper from directly gaining access to the
   drop- and accept-listed IP addresses.

   An attacker may be able to inject RST packets, bogus application
   segments, etc., regardless of whether TLS authentication is used.
   Because the application data is TLS protected, this will not result
   in the application receiving bogus data, but it will constitute a DoS
   on the connection.  This attack can be countered by using TCP-AO
   [RFC5925].  If TCP-AO is used, then any bogus packets injected by an
   attacker will be rejected by the TCP-AO integrity check and therefore
   will never reach the TLS layer.

   In order to prevent leaking internal information outside a client-
   domain, client-side DOTS gateways SHOULD NOT reveal the identity of




Boucadair & Reddy        Expires January 4, 2020               [Page 61]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   internal DOTS clients (e.g., source IP address, client's hostname)
   unless explicitly configured to do so.

   DOTS servers MUST verify that requesting DOTS clients are entitled to
   enforce filtering rules on a given IP prefix.  That is, only
   filtering rules on IP resources that belong to the DOTS client domain
   can be authorized by a DOTS server.  The exact mechanism for the DOTS
   servers to validate that the target prefixes are within the scope of
   the DOTS client domain is deployment-specific.

   Rate-limiting DOTS requests, including those with new 'cuid' values,
   from the same DOTS client defends against DoS attacks that would
   result from varying the 'cuid' to exhaust DOTS server resources.
   Rate-limit policies SHOULD be enforced on DOTS gateways (if deployed)
   and DOTS servers.

   Applying resources quota per DOTS client and/or per DOTS client
   domain (e.g., limit the number of aliases and filters to be installed
   by DOTS clients) prevents DOTS server resources to be aggressively
   used by some DOTS clients and ensures, therefore, DDoS mitigation
   usage fairness.  Additionally, DOTS servers may limit the number of
   DOTS clients that can be enabled per domain.

   When FQDNs are used as targets, the DOTS server MUST rely upon DNS
   privacy enabling protocols (e.g., DNS over TLS [RFC7858] or DoH
   [RFC8484]) to prevent eavesdroppers from possibly identifying the
   target resources protected by the DDoS mitigation service, and means
   to ensure the target FQDN resolution is authentic (e.g., DNSSEC
   [RFC4034]).

   The presence of DOTS gateways may lead to infinite forwarding loops,
   which is undesirable.  To prevent and detect such loops, a mechanism
   is defined in Section 3.4.

   All data nodes defined in the YANG module which can be created,
   modified, and deleted (i.e., config true, which is the default) are
   considered sensitive.  Write operations applied to these data nodes
   without proper protection can negatively affect network operations.
   This module reuses YANG structures from [RFC8519], and the security
   considerations for those nodes continue to apply for this usage.
   Appropriate security measures are recommended to prevent illegitimate
   users from invoking DOTS data channel primitives.  Nevertheless, an
   attacker who can access a DOTS client is technically capable of
   launching various attacks, such as:

   o  Setting an arbitrarily low rate-limit, which may prevent
      legitimate traffic from being forwarded (rate-limit).




Boucadair & Reddy        Expires January 4, 2020               [Page 62]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   o  Setting an arbitrarily high rate-limit, which may lead to the
      forwarding of illegitimate DDoS traffic (rate-limit).

   o  Communicating invalid aliases to the server (alias), which will
      cause the failure of associating both data and signal channels.

   o  Setting invalid ACL entries, which may prevent legitimate traffic
      from being forwarded.  Likewise, invalid ACL entries may lead to
      forward DDoS traffic.

11.  Contributing Authors

   The following individuals co-authored this document:






































Boucadair & Reddy        Expires January 4, 2020               [Page 63]


Internet-Draft         DOTS Data Channel Protocol              July 2019


      Kaname Nishizuka
      NTT Communications
      GranPark 16F 3-4-1 Shibaura, Minato-ku
      Tokyo  108-8118
      Japan

      Email: kaname@nttv6.jp


      Liang Xia
      Huawei
      101 Software Avenue, Yuhuatai District
      Nanjing, Jiangsu  210012
      China

      Email: frank.xialiang@huawei.com


      Prashanth Patil
      Cisco Systems, Inc.

      Email: praspati@cisco.com


      Andrew Mortensen
      Arbor Networks, Inc.
      2727 S. State St
      Ann Arbor, MI  48104
      United States

      Email: andrew.mortensen@netscout.com


      Nik Teague
      Iron Mountain Data Centers
      United Kingdom

      Email: nteague@ironmountain.co.uk

12.  Contributors

   The following individuals have contributed to this document:

   o  Dan Wing, Email: dwing-ietf@fuggles.com

   o  Jon Shallow, NCC Group, Email: jon.shallow@nccgroup.com





Boucadair & Reddy        Expires January 4, 2020               [Page 64]


Internet-Draft         DOTS Data Channel Protocol              July 2019


13.  Acknowledgements

   Thanks to Christian Jacquenet, Roland Dobbins, Roman Danyliw, Ehud
   Doron, Russ White, Gilbert Clark, Kathleen Moriarty, Nesredien
   Suleiman, Roni Even, and Brian Trammel for the discussion and
   comments.

   The authors would like to give special thanks to Kaname Nishizuka and
   Jon Shallow for their efforts in implementing the protocol and
   performing interop testing at IETF Hackathons.

   Many thanks to Ben Kaduk for the detailed AD review.

   Thanks to Martin Bjorklund for the guidance on RESTCONF.

   Thanks to Alexey Melnikov, Adam Roach, Suresh Krishnan, Mirja
   Kuehlewind, and Warren Kumari for the review.

14.  References

14.1.  Normative References

   [I-D.ietf-dots-signal-channel]
              K, R., Boucadair, M., Patil, P., Mortensen, A., and N.
              Teague, "Distributed Denial-of-Service Open Threat
              Signaling (DOTS) Signal Channel Specification", draft-
              ietf-dots-signal-channel-34 (work in progress), May 2019.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/info/rfc3688>.

   [RFC4632]  Fuller, V. and T. Li, "Classless Inter-domain Routing
              (CIDR): The Internet Address Assignment and Aggregation
              Plan", BCP 122, RFC 4632, DOI 10.17487/RFC4632, August
              2006, <https://www.rfc-editor.org/info/rfc4632>.

   [RFC6125]  Saint-Andre, P. and J. Hodges, "Representation and
              Verification of Domain-Based Application Service Identity
              within Internet Public Key Infrastructure Using X.509
              (PKIX) Certificates in the Context of Transport Layer
              Security (TLS)", RFC 6125, DOI 10.17487/RFC6125, March
              2011, <https://www.rfc-editor.org/info/rfc6125>.



Boucadair & Reddy        Expires January 4, 2020               [Page 65]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
              RFC 6991, DOI 10.17487/RFC6991, July 2013,
              <https://www.rfc-editor.org/info/rfc6991>.

   [RFC7230]  Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer
              Protocol (HTTP/1.1): Message Syntax and Routing",
              RFC 7230, DOI 10.17487/RFC7230, June 2014,
              <https://www.rfc-editor.org/info/rfc7230>.

   [RFC7525]  Sheffer, Y., Holz, R., and P. Saint-Andre,
              "Recommendations for Secure Use of Transport Layer
              Security (TLS) and Datagram Transport Layer Security
              (DTLS)", BCP 195, RFC 7525, DOI 10.17487/RFC7525, May
              2015, <https://www.rfc-editor.org/info/rfc7525>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC7951]  Lhotka, L., "JSON Encoding of Data Modeled with YANG",
              RFC 7951, DOI 10.17487/RFC7951, August 2016,
              <https://www.rfc-editor.org/info/rfc7951>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8259]  Bray, T., Ed., "The JavaScript Object Notation (JSON) Data
              Interchange Format", STD 90, RFC 8259,
              DOI 10.17487/RFC8259, December 2017,
              <https://www.rfc-editor.org/info/rfc8259>.

   [RFC8519]  Jethanandani, M., Agarwal, S., Huang, L., and D. Blair,
              "YANG Data Model for Network Access Control Lists (ACLs)",
              RFC 8519, DOI 10.17487/RFC8519, March 2019,
              <https://www.rfc-editor.org/info/rfc8519>.

14.2.  Informative References

   [I-D.ietf-dots-architecture]
              Mortensen, A., K, R., Andreasen, F., Teague, N., and R.
              Compton, "Distributed-Denial-of-Service Open Threat
              Signaling (DOTS) Architecture", draft-ietf-dots-
              architecture-14 (work in progress), May 2019.



Boucadair & Reddy        Expires January 4, 2020               [Page 66]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   [I-D.ietf-dots-server-discovery]
              Boucadair, M. and R. K, "Distributed-Denial-of-Service
              Open Threat Signaling (DOTS) Server Discovery", draft-
              ietf-dots-server-discovery-04 (work in progress), June
              2019.

   [proto_numbers]
              "IANA, "Protocol Numbers"", 2011,
              <http://www.iana.org/assignments/protocol-numbers>.

   [RFC1122]  Braden, R., Ed., "Requirements for Internet Hosts -
              Communication Layers", STD 3, RFC 1122,
              DOI 10.17487/RFC1122, October 1989,
              <https://www.rfc-editor.org/info/rfc1122>.

   [RFC3986]  Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
              Resource Identifier (URI): Generic Syntax", STD 66,
              RFC 3986, DOI 10.17487/RFC3986, January 2005,
              <https://www.rfc-editor.org/info/rfc3986>.

   [RFC4034]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "Resource Records for the DNS Security Extensions",
              RFC 4034, DOI 10.17487/RFC4034, March 2005,
              <https://www.rfc-editor.org/info/rfc4034>.

   [RFC4340]  Kohler, E., Handley, M., and S. Floyd, "Datagram
              Congestion Control Protocol (DCCP)", RFC 4340,
              DOI 10.17487/RFC4340, March 2006,
              <https://www.rfc-editor.org/info/rfc4340>.

   [RFC4960]  Stewart, R., Ed., "Stream Control Transmission Protocol",
              RFC 4960, DOI 10.17487/RFC4960, September 2007,
              <https://www.rfc-editor.org/info/rfc4960>.

   [RFC5575]  Marques, P., Sheth, N., Raszuk, R., Greene, B., Mauch, J.,
              and D. McPherson, "Dissemination of Flow Specification
              Rules", RFC 5575, DOI 10.17487/RFC5575, August 2009,
              <https://www.rfc-editor.org/info/rfc5575>.

   [RFC5925]  Touch, J., Mankin, A., and R. Bonica, "The TCP
              Authentication Option", RFC 5925, DOI 10.17487/RFC5925,
              June 2010, <https://www.rfc-editor.org/info/rfc5925>.

   [RFC6520]  Seggelmann, R., Tuexen, M., and M. Williams, "Transport
              Layer Security (TLS) and Datagram Transport Layer Security
              (DTLS) Heartbeat Extension", RFC 6520,
              DOI 10.17487/RFC6520, February 2012,
              <https://www.rfc-editor.org/info/rfc6520>.



Boucadair & Reddy        Expires January 4, 2020               [Page 67]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   [RFC7858]  Hu, Z., Zhu, L., Heidemann, J., Mankin, A., Wessels, D.,
              and P. Hoffman, "Specification for DNS over Transport
              Layer Security (TLS)", RFC 7858, DOI 10.17487/RFC7858, May
              2016, <https://www.rfc-editor.org/info/rfc7858>.

   [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
              BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
              <https://www.rfc-editor.org/info/rfc8340>.

   [RFC8484]  Hoffman, P. and P. McManus, "DNS Queries over HTTPS
              (DoH)", RFC 8484, DOI 10.17487/RFC8484, October 2018,
              <https://www.rfc-editor.org/info/rfc8484>.

   [RFC8499]  Hoffman, P., Sullivan, A., and K. Fujiwara, "DNS
              Terminology", BCP 219, RFC 8499, DOI 10.17487/RFC8499,
              January 2019, <https://www.rfc-editor.org/info/rfc8499>.

   [RFC8612]  Mortensen, A., Reddy, T., and R. Moskowitz, "DDoS Open
              Threat Signaling (DOTS) Requirements", RFC 8612,
              DOI 10.17487/RFC8612, May 2019,
              <https://www.rfc-editor.org/info/rfc8612>.

Appendix A.  Sample Examples: Filtering Fragments

   This specification strongly recommends the use of "fragment" for
   handling fragments.

   Figure 34 shows the content of the POST request to be issued by a
   DOTS client to its DOTS server to allow the traffic destined to
   198.51.100.0/24 and UDP port number 53, but to drop all fragmented
   packets.  The following ACEs are defined (in this order):

   o  "drop-all-fragments" ACE: discards all fragments.

   o  "allow-dns-packets" ACE: accepts DNS packets destined to
      198.51.100.0/24.

    POST /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
    Host: example.com
    Content-Type: application/yang-data+json

    {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "dns-fragments",
           "type": "ipv4-acl-type",



Boucadair & Reddy        Expires January 4, 2020               [Page 68]


Internet-Draft         DOTS Data Channel Protocol              July 2019


           "aces": {
             "ace": [
               {
                 "name": "drop-all-fragments",
                 "matches": {
                   "ipv4": {
                     "fragment": {
                       "operator": "match",
                       "type": "isf"
                     }
                   }
                 },
                 "actions": {
                   "forwarding": "drop"
                 }
               }
             ]
             "ace": [
               {
                 "name": "allow-dns-packets",
                 "matches": {
                   "ipv4": {
                     "destination-ipv4-network": "198.51.100.0/24"
                   }
                   "udp": {
                     "destination-port": {
                       "operator": "eq",
                       "port": 53
                   }
                 },
                 "actions": {
                   "forwarding": "accept"
                 }
               }
             ]
           }
         }
       ]
     }
    }

               Figure 34: Filtering IPv4 Fragmented Packets

   Figure 35 shows a POST request example issued by a DOTS client to its
   DOTS server to allow the traffic destined to 2001:db8::/32 and UDP
   port number 53, but to drop all fragmented packets.  The following
   ACEs are defined (in this order):




Boucadair & Reddy        Expires January 4, 2020               [Page 69]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   o  "drop-all-fragments" ACE: discards all fragments (including atomic
      fragments).  That is, IPv6 packets which include a Fragment header
      (44) are dropped.

   o  "allow-dns-packets" ACE: accepts DNS packets destined to
      2001:db8::/32.

    POST /restconf/data/ietf-dots-data-channel:dots-data\
         /dots-client=dz6pHjaADkaFTbjr0JGBpw HTTP/1.1
    Host: example.com
    Content-Type: application/yang-data+json

    {
     "ietf-dots-data-channel:acls": {
       "acl": [
         {
           "name": "dns-fragments",
           "type": "ipv6-acl-type",
           "aces": {
             "ace": [
               {
                 "name": "drop-all-fragments",
                 "matches": {
                   "ipv6": {
                     "fragment": {
                       "operator": "match",
                       "type": "isf"
                     }
                   }
                 },
                 "actions": {
                   "forwarding": "drop"
                 }
               }
             ]
             "ace": [
               {
                 "name": "allow-dns-packets",
                 "matches": {
                   "ipv6": {
                     "destination-ipv6-network": "2001:db8::/32"
                   }
                   "udp": {
                     "destination-port": {
                       "operator": "eq",
                       "port": 53
                     }
                   }



Boucadair & Reddy        Expires January 4, 2020               [Page 70]


Internet-Draft         DOTS Data Channel Protocol              July 2019


                 },
                 "actions": {
                   "forwarding": "accept"
                 }
               }
             ]
           }
         }
       ]
     }
    }

               Figure 35: Filtering IPv6 Fragmented Packets

Appendix B.  Sample Examples: Filtering TCP Messages

   This section provides sample examples to illustrate TCP-specific
   filtering based on the flag bits.  These examples should not be
   interpreted as recommended filtering behaviors under specific DDoS
   attacks.

B.1.  Discard TCP Null Attack

   Figure 36 shows an example of a DOTS request sent by a DOTS client to
   install immediately a filter to discard incoming TCP messages having
   all flags unset.  The bitmask can be set to 255 to check against the
   (CWR, ECE, URG, ACK, PSH, RST, SYN, FIN) flags.
























Boucadair & Reddy        Expires January 4, 2020               [Page 71]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   PUT /restconf/data/ietf-dots-data-channel:dots-data\
       /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
       /acl=tcp-flags-example HTTP/1.1
   Host: example.com
   Content-Type: application/yang-data+json

   {
     "ietf-dots-data-channel:acls": {
       "acl": [{
         "name": "tcp-flags-example",
         "activation-type": "immediate",
         "aces": {
           "ace": [{
             "name": "null-attack",
             "matches": {
               "tcp": {
                 "flags-bitmask": {
                   "operator": "not any",
                   "bitmask": 4095
                 }
               }
             },
             "actions": {
               "forwarding": "drop"
             }
           }]
         }
       }]
     }
   }

   Figure 36: Example of a DOTS Request to Deny TCP Null Attack Messages

B.2.  Rate-Limit SYN Flooding

   Figure 37 shows an ACL example to rate-limit incoming SYNs during a
   SYN-flood attack.














Boucadair & Reddy        Expires January 4, 2020               [Page 72]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   PUT /restconf/data/ietf-dots-data-channel:dots-data\
       /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
       /acl=tcp-flags-example HTTP/1.1
   Host: example.com
   Content-Type: application/yang-data+json

   {
     "ietf-dots-data-channel:acls": {
       "acl": [{
         "name": "tcp-flags-example",
         "activation-type": "activate-when-mitigating",
         "aces": {
           "ace": [{
             "name": "rate-limit-syn",
             "matches": {
               "tcp": {
                 "flags-bitmask": {
                   "operator": "match",
                   "bitmask": 2
                 }
               }
             },
             "actions": {
               "forwarding": "accept",
               "rate-limit": "20.00"
             }
           }]
         }
       }]
     }
   }

    Figure 37: Example of DOTS Request to Rate-Limit Incoming TCP SYNs

B.3.  Rate-Limit ACK Flooding

   Figure 38 shows an ACL example to rate-limit incoming ACKs during an
   ACK-flood attack.













Boucadair & Reddy        Expires January 4, 2020               [Page 73]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   PUT /restconf/data/ietf-dots-data-channel:dots-data\
       /dots-client=paL8p4Zqo4SLv64TLPXrxA/acls\
       /acl=tcp-flags-example HTTP/1.1
   Host: example.com
   Content-Type: application/yang-data+json

   {
     "ietf-dots-data-channel:acls": {
       "acl": [{
         "name": "tcp-flags-example",
         "type": "ipv4-acl-type",
         "activation-type": "activate-when-mitigating",
         "aces": {
           "ace": [{
             "name": "rate-limit-ack",
             "matches": {
               "tcp": {
                 "flags-bitmask": {
                   "operator": "match",
                   "bitmask": 16
                 }
               }
             },
             "actions": {
               "forwarding": "accept",
               "rate-limit": "20.00"
             }
           }]
         }
       }]
     }
   }

    Figure 38: Example of DOTS Request to Rate-Limit Incoming TCP ACKs

Authors' Addresses

   Mohamed Boucadair (editor)
   Orange
   Rennes  35000
   France

   Email: mohamed.boucadair@orange.com








Boucadair & Reddy        Expires January 4, 2020               [Page 74]


Internet-Draft         DOTS Data Channel Protocol              July 2019


   Tirumaleswar Reddy (editor)
   McAfee, Inc.
   Embassy Golf Link Business Park
   Bangalore, Karnataka  560071
   India

   Email: kondtir@gmail.com












































Boucadair & Reddy        Expires January 4, 2020               [Page 75]