dprive W. Toorop
Internet-Draft NLnet Labs
Updates: 1995, 5936, 7766 (if approved) S. Dickinson
Intended status: Standards Track Sinodun IT
Expires: September 9, 2021 S. Sahib
P. Aras
A. Mankin
Salesforce
March 8, 2021
DNS Zone Transfer-over-TLS
draft-ietf-dprive-xfr-over-tls-08
Abstract
DNS zone transfers are transmitted in clear text, which gives
attackers the opportunity to collect the content of a zone by
eavesdropping on network connections. The DNS Transaction Signature
(TSIG) mechanism is specified to restrict direct zone transfer to
authorized clients only, but it does not add confidentiality. This
document specifies the use of TLS, rather than clear text, to prevent
zone content collection via passive monitoring of zone transfers:
XFR-over-TLS (XoT). Additionally, this specification updates
RFC1995, RFC5936 and RFC7766.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 9, 2021.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
Toorop, et al. Expires September 9, 2021 [Page 1]
Internet-Draft XFR-over-TLS March 2021
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Document work via GitHub . . . . . . . . . . . . . . . . . . 5
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Use Cases for XFR-over-TLS . . . . . . . . . . . . . . . . . 6
4.1. Threat model . . . . . . . . . . . . . . . . . . . . . . 6
5. Connection and Data Flows in Existing XFR Mechanisms . . . . 7
5.1. AXFR Mechanism . . . . . . . . . . . . . . . . . . . . . 7
5.2. IXFR Mechanism . . . . . . . . . . . . . . . . . . . . . 9
5.3. Data Leakage of NOTIFY and SOA Message Exchanges . . . . 11
5.3.1. NOTIFY . . . . . . . . . . . . . . . . . . . . . . . 11
5.3.2. SOA . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Updates to existing specifications . . . . . . . . . . . . . 11
6.1. Update to RFC1995 for IXFR-over-TCP . . . . . . . . . . . 13
6.2. Update to RFC5936 for AXFR-over-TCP . . . . . . . . . . . 13
6.3. Updates to RFC1995 and RFC5936 for XFR-over-TCP . . . . . 13
6.3.1. Connection reuse . . . . . . . . . . . . . . . . . . 13
6.3.2. AXFRs and IXFRs on the same connection . . . . . . . 14
6.3.3. XFR limits . . . . . . . . . . . . . . . . . . . . . 14
6.3.4. The edns-tcp-keepalive EDNS0 Option . . . . . . . . . 15
6.3.5. Backwards compatibility . . . . . . . . . . . . . . . 15
6.4. Update to RFC7766 . . . . . . . . . . . . . . . . . . . . 15
7. XoT specification . . . . . . . . . . . . . . . . . . . . . . 17
7.1. TLS versions . . . . . . . . . . . . . . . . . . . . . . 17
7.2. Port selection . . . . . . . . . . . . . . . . . . . . . 17
7.3. High level XoT descriptions . . . . . . . . . . . . . . . 17
7.4. XoT transfers . . . . . . . . . . . . . . . . . . . . . . 19
7.5. XoT connections . . . . . . . . . . . . . . . . . . . . . 20
7.6. XoT vs ADoT . . . . . . . . . . . . . . . . . . . . . . . 20
7.7. Response RCODES . . . . . . . . . . . . . . . . . . . . . 21
7.8. AXoT specifics . . . . . . . . . . . . . . . . . . . . . 21
7.8.1. Padding AXoT responses . . . . . . . . . . . . . . . 21
7.9. IXoT specifics . . . . . . . . . . . . . . . . . . . . . 22
7.9.1. Condensation of responses . . . . . . . . . . . . . . 22
7.9.2. Fallback to AXFR . . . . . . . . . . . . . . . . . . 22
7.9.3. Padding of IXoT responses . . . . . . . . . . . . . . 23
7.10. Name compression and maximum payload sizes . . . . . . . 23
Toorop, et al. Expires September 9, 2021 [Page 2]
Internet-Draft XFR-over-TLS March 2021
8. Multi-primary Configurations . . . . . . . . . . . . . . . . 23
9. Authentication mechanisms . . . . . . . . . . . . . . . . . . 24
9.1. TSIG . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2. SIG(0) . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.3. TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.3.1. Opportunistic TLS . . . . . . . . . . . . . . . . . . 25
9.3.2. Strict TLS . . . . . . . . . . . . . . . . . . . . . 26
9.3.3. Mutual TLS . . . . . . . . . . . . . . . . . . . . . 26
9.4. IP Based ACL on the Primary . . . . . . . . . . . . . . . 26
9.5. ZONEMD . . . . . . . . . . . . . . . . . . . . . . . . . 27
10. XoT authentication . . . . . . . . . . . . . . . . . . . . . 27
11. Policies for Both AXoT and IXoT . . . . . . . . . . . . . . . 28
12. Implementation Considerations . . . . . . . . . . . . . . . . 29
13. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 29
14. Implementation Status . . . . . . . . . . . . . . . . . . . . 29
15. Security Considerations . . . . . . . . . . . . . . . . . . . 30
16. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 30
17. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 30
18. Changelog . . . . . . . . . . . . . . . . . . . . . . . . . . 31
19. References . . . . . . . . . . . . . . . . . . . . . . . . . 33
19.1. Normative References . . . . . . . . . . . . . . . . . . 33
19.2. Informative References . . . . . . . . . . . . . . . . . 34
19.3. URIs . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix A. XoT server connection handling . . . . . . . . . . . 36
A.1. Only listen on TLS on a specific IP address . . . . . . . 37
A.2. Client specific TLS acceptance . . . . . . . . . . . . . 37
A.3. SNI based TLS acceptance . . . . . . . . . . . . . . . . 37
A.4. TLS specific response policies . . . . . . . . . . . . . 37
A.4.1. SNI based response policies . . . . . . . . . . . . . 38
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 39
1. Introduction
DNS has a number of privacy vulnerabilities, as discussed in detail
in [RFC7626]. Stub client to recursive resolver query privacy has
received the most attention to date, with standards track documents
for both DNS-over-TLS (DoT) [RFC7858] and DNS-over-HTTPS (DoH)
[RFC8484], and a proposal for DNS-over-QUIC
[I-D.ietf-dprive-dnsoquic]. There is ongoing work on DNS privacy
requirements for exchanges between recursive resolvers and
authoritative servers [I-D.ietf-dprive-phase2-requirements] and some
suggestions for how signaling of DoT support by authoritatives might
work, e.g., [I-D.vandijk-dprive-ds-dot-signal-and-pin]. However
there is currently no RFC that specifically defines recursive to
authoritative DNS-over-TLS (ADoT).
Toorop, et al. Expires September 9, 2021 [Page 3]
Internet-Draft XFR-over-TLS March 2021
[RFC7626] established that stub client DNS query transactions are not
public and needed protection, but on zone transfer [RFC1995]
[RFC5936] it says only:
"Privacy risks for the holder of a zone (the risk that someone
gets the data) are discussed in [RFC5936] and [RFC5155]."
In what way is exposing the full contents of a zone a privacy risk?
The contents of the zone could include information such as names of
persons used in names of hosts. Best practice is not to use personal
information for domain names, but many such domain names exist. The
contents of the zone could also include references to locations that
allow inference about location information of the individuals
associated with the zone's organization. It could also include
references to other organizations. Examples of this could be:
o Person-laptop.example.org
o MX-for-Location.example.org
o Service-tenant-from-another-org.example.org
There may also be regulatory, policy or other reasons why the zone
contents in full must be treated as private.
Neither of the RFCs mentioned in [RFC7626] contemplates the risk that
someone gets the data through eavesdropping on network connections,
only via enumeration or unauthorized transfer as described in the
following paragraphs.
Zone enumeration is trivially possible for DNSSEC zones which use
NSEC; i.e. queries for the authenticated denial of existences
records allow a client to walk through the entire zone contents.
[RFC5155] specifies NSEC3, a mechanism to provide measures against
zone enumeration for DNSSEC signed zones (a goal was to make it as
hard to enumerate an DNSSEC signed zone as an unsigned zone). Whilst
this is widely used, zone walking is now possible with NSEC3 due to
crypto-breaking advances. This has prompted further work on an
alternative mechanism for DNSSEC authenticated denial of existence -
NSEC5 [I-D.vcelak-nsec5] - however questions remain over the
practicality of this mechanism.
[RFC5155] does not address data obtained outside zone enumeration
(nor does [I-D.vcelak-nsec5]). Preventing eavesdropping of zone
transfers (this draft) is orthogonal to preventing zone enumeration,
though they aim to protect the same information.
Toorop, et al. Expires September 9, 2021 [Page 4]
Internet-Draft XFR-over-TLS March 2021
[RFC5936] specifies using TSIG [RFC8945] for authorization of the
clients of a zone transfer and for data integrity, but does not
express any need for confidentiality, and TSIG does not offer
encryption. Some operators use SSH tunneling or IPSec to encrypt the
transfer data.
Section 8 of the NIST guide on 'Secure Domain Name System (DNS)
Deployment' [nist-guide] discusses restricting access for zone
transfers using ACLs and TSIG in more detail. It is noted that in
all the common open source implementations such ACLs are applied on a
per query basis. Since requests typically occur on TCP connections
authoritatives must cater for accepting any TCP connection and then
handling the authentication of each XFR request individually.
Because both AXFR and IXFR zone transfers are typically carried out
over TCP from authoritative DNS protocol implementations, encrypting
zone transfers using TLS, based closely on DoT [RFC7858], seems like
a simple step forward. This document specifies how to use TLS as a
transport to prevent zone collection from zone transfers.
2. Document work via GitHub
[THIS SECTION TO BE REMOVED BEFORE PUBLICATION] The Github repository
for this document is at <https://github.com/hanzhang0116/hzpa-dprive-
xfr-over-tls>. Proposed text and editorial changes are very much
welcomed there, but any functional changes should always first be
discussed on the IETF DPRIVE WG (dns-privacy) mailing list.
3. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] and [RFC8174] when, and only when, they appear in all
capitals, as shown here.
Privacy terminology is as described in Section 3 of [RFC6973].
Note that in this document we choose to use the terms 'primary' and
'secondary' for two servers engaged in zone transfers.
DNS terminology is as described in [RFC8499].
DoT: DNS-over-TLS as specified in [RFC7858]
XFR-over-TCP: Used to mean both IXFR-over-TCP [RFC1995] and AXFR-
over-TCP [RFC5936].
Toorop, et al. Expires September 9, 2021 [Page 5]
Internet-Draft XFR-over-TLS March 2021
XoT: Generic XFR-over-TLS mechanisms as specified in this document
AXoT: AXFR-over-TLS
IXoT: IXFR over-TLS
4. Use Cases for XFR-over-TLS
o Confidentiality. Clearly using an encrypted transport for zone
transfers will defeat zone content leakage that can occur via
passive surveillance.
o Authentication. Use of single or mutual TLS (mTLS) authentication
(in combination with ACLs) can complement and potentially be an
alternative to TSIG.
o Performance. Existing AXFR and IXFR mechanisms have the burden of
backwards compatibility with older implementations based on the
original specifications in [RFC1034] and [RFC1035]. For example,
some older AXFR servers don't support using a TCP connection for
multiple AXFR sessions or XFRs of different zones because they
have not been updated to follow the guidance in [RFC5936]. Any
implementation of XFR-over-TLS (XoT) would obviously be required
to implement optimized and interoperable transfers as described in
[RFC5936], e.g., transfer of multiple zones over one connection.
o Performance. Current usage of TCP for IXFR is sub-optimal in some
cases i.e. connections are frequently closed after a single IXFR.
4.1. Threat model
The threat model considered here is one where the current contents
and size of the zone are considered sensitive and should be protected
during transfer.
The threat model does not, however, consider the existence of a zone,
the act of zone transfer between two entities, nor the identities of
the nameservers hosting a zone (including both those acting as hidden
primaries/secondaries or directly serving the zone) as sensitive
information. The proposed mechanisms does not attempt to obscure
such information. The reasons for this include:
o much of this information can be obtained by various methods
including active scanning of the DNS
o an attacker who can monitor network traffic can relatively easily
infer relations between nameservers simply from traffic patterns,
even when some or all of the traffic is encrypted
Toorop, et al. Expires September 9, 2021 [Page 6]
Internet-Draft XFR-over-TLS March 2021
It is noted that simply using XoT will indicate a desire by the zone
owner that the contents of the zone remain confidential and so could
be subject to blocking (e.g. via blocking of port 853) if an attacker
had such capabilities. However this threat is likely true of any
such mechanism that attempts to encrypt data passed between
nameservers e.g. IPsec.
5. Connection and Data Flows in Existing XFR Mechanisms
The original specification for zone transfers in [RFC1034] and
[RFC1035] was based on a polling mechanism: a secondary performed a
periodic SOA query (based on the refresh timer) to determine if an
AXFR was required.
[RFC1995] and [RFC1996] introduced the concepts of IXFR and NOTIFY
respectively, to provide for prompt propagation of zone updates.
This has largely replaced AXFR where possible, particularly for
dynamically updated zones.
[RFC5936] subsequently redefined the specification of AXFR to improve
performance and interoperability.
In this document we use the term "XFR mechanism" to describe the
entire set of message exchanges between a secondary and a primary
that concludes in a successful AXFR or IXFR request/response. This
set may or may not include
o NOTIFY messages
o SOA queries
o Fallback from IXFR to AXFR
o Fallback from IXFR-over-UDP to IXFR-over-TCP
The term is used to encompasses the range of permutations that are
possible and is useful to distinguish the 'XFR mechanism' from a
single XFR request/response exchange.
5.1. AXFR Mechanism
The figure below provides an outline of an AXFR mechanism including
NOTIFYs.
Toorop, et al. Expires September 9, 2021 [Page 7]
Internet-Draft XFR-over-TLS March 2021
Secondary Primary
| NOTIFY |
| <-------------------------------- | UDP
| --------------------------------> |
| NOTIFY Response |
| |
| |
| SOA Request |
| --------------------------------> | UDP (or part of
| <-------------------------------- | a TCP session)
| SOA Response |
| |
| |
| |
| AXFR Request | ---
| --------------------------------> | |
| <-------------------------------- | |
| AXFR Response 1 | |
| (Zone data) | |
| | |
| <-------------------------------- | | TCP
| AXFR Response 2 | | Session
| (Zone data) | |
| | |
| <-------------------------------- | |
| AXFR Response 3 | |
| (Zone data) | ---
| |
Figure 1. AXFR Mechanism
1. An AXFR is often (but not always) preceded by a NOTIFY (over UDP)
from the primary to the secondary. A secondary may also initiate
an AXFR based on a refresh timer or scheduled/triggered zone
maintenance.
2. The secondary will normally (but not always) make a SOA query to
the primary to obtain the serial number of the zone held by the
primary.
3. If the primary serial is higher than the secondaries serial
(using Serial Number Arithmetic [RFC1982]), the secondary makes
an AXFR request (over TCP) to the primary after which the AXFR
data flows in one or more AXFR responses on the TCP connection.
[RFC5936] defines this specific step as an 'AXFR session' i.e. as
Toorop, et al. Expires September 9, 2021 [Page 8]
Internet-Draft XFR-over-TLS March 2021
an AXFR query message and the sequence of AXFR response messages
returned for it.
[RFC5936] re-specified AXFR providing additional guidance beyond that
provided in [RFC1034] and [RFC1035] and importantly specified that
AXFR must use TCP as the transport protocol.
Additionally, sections 4.1, 4.1.1 and 4.1.2 of [RFC5936] provide
improved guidance for AXFR clients and servers with regard to re-use
of TCP connections for multiple AXFRs and AXFRs of different zones.
However [RFC5936] was constrained by having to be backwards
compatible with some very early basic implementations of AXFR. For
example, it outlines that the SOA query can also happen on this
connection. However, this can cause interoperability problems with
older implementations that support only the trivial case of one AXFR
per connection.
5.2. IXFR Mechanism
The figure below provides an outline of the IXFR mechanism including
NOTIFYs.
Toorop, et al. Expires September 9, 2021 [Page 9]
Internet-Draft XFR-over-TLS March 2021
Secondary Primary
| NOTIFY |
| <-------------------------------- | UDP
| --------------------------------> |
| NOTIFY Response |
| |
| |
| SOA Request |
| --------------------------------> | UDP or TCP
| <-------------------------------- |
| SOA Response |
| |
| |
| |
| IXFR Request |
| --------------------------------> | UDP or TCP
| <-------------------------------- |
| IXFR Response |
| (Zone data) |
| |
| | ---
| IXFR Request | |
| --------------------------------> | | Retry over
| <-------------------------------- | | TCP if
| IXFR Response | | required
| (Zone data) | ---
Figure 2. IXFR Mechanism
1. An IXFR is normally (but not always) preceded by a NOTIFY (over
UDP) from the primary to the secondary. A secondary may also
initiate an IXFR based on a refresh timer or scheduled/triggered
zone maintenance.
2. The secondary will normally (but not always) make a SOA query to
the primary to obtain the serial number of the zone held by the
primary.
3. If the primary serial is higher than the secondaries serial
(using Serial Number Arithmetic [RFC1982]), the secondary makes
an IXFR request to the primary after which the primary sends an
IXFR response.
[RFC1995] specifies that Incremental Transfer may use UDP if the
entire IXFR response can be contained in a single DNS packet,
otherwise, TCP is used. In fact it says:
Toorop, et al. Expires September 9, 2021 [Page 10]
Internet-Draft XFR-over-TLS March 2021
"Thus, a client should first make an IXFR query using UDP."
So there may be a fourth step above where the client falls back to
IXFR-over-TCP. There may also be a fourth step where the secondary
must fall back to AXFR because, e.g., the primary does not support
IXFR.
However it is noted that most widely used open source authoritative
nameserver implementations (including both [BIND] and [NSD] do IXFR
using TCP by default in their latest releases. For BIND TCP
connections are sometimes used for SOA queries but in general they
are not used persistently and close after an IXFR is completed.
5.3. Data Leakage of NOTIFY and SOA Message Exchanges
This section attempts to presents a rationale for considering
encrypting the other messages in the XFR mechanism.
Since the SOA of the published zone can be trivially discovered by
simply querying the publicly available authoritative servers leakage
of this RR is not discussed in the following sections.
5.3.1. NOTIFY
Unencrypted NOTIFY messages identify configured secondaries on the
primary.
[RFC1996] also states:
"If ANCOUNT>0, then the answer section represents an
unsecure hint at the new RRset for this (QNAME,QCLASS,QTYPE).
But since the only supported QTYPE for NOTIFY is SOA, this does not
pose a potential leak.
5.3.2. SOA
For hidden primaries or secondaries the SOA response leaks only the
degree of lag of any downstream secondary.
6. Updates to existing specifications
For convenience, the term 'XFR-over-TCP' is used in this document to
mean both IXFR-over-TCP and AXFR-over-TCP and therefore statements
that use that term update both [RFC1995] and [RFC5936], and
implicitly also apply to XoT. Differences in behavior specific to
XoT are discussed in Section 7.
Toorop, et al. Expires September 9, 2021 [Page 11]
Internet-Draft XFR-over-TLS March 2021
Both [RFC1995] and [RFC5936] were published sometime before TCP was
considered a first class transport for DNS. [RFC1995], in fact, says
nothing with respect to optimizing IXFRs over TCP or re-using already
open TCP connections to perform IXFRs or other queries. Therefore,
there arguably is an implicit assumption (probably unintentional)
that a TCP connection is used for one and only one IXFR request.
Indeed, many major open source implementations currently take this
approach. And whilst [RFC5936] gives guidance on connection re-use
for AXFR, it pre-dates more recent specifications describing
persistent TCP connections e.g. [RFC7766], [RFC7828] and AXFR
implementations again often make less than optimal use of open
connections.
Given this, new implementations of XoT will clearly benefit from
specific guidance on TCP/TLS connection usage for XFR because this
will:
o result in more consistent XoT implementations with better
interoperability
o remove any need for XoT implementations to support legacy behavior
that XFR-over-TCP implementations have historically often
supported
Therefore this document updates both the previous specifications for
XFR-over-TCP to clarify that
o Implementations MUST use [RFC7766] (DNS Transport over TCP -
Implementation Requirements) to optimize the use of TCP
connections.
o Whilst RFC7766 states that 'DNS clients SHOULD pipeline their
queries' on TCP connections, it did not distinguish between XFRs
and other queries for this behavior. It is now recognized that
XFRs are not as latency sensitive as other queries, and can be
significantly more complex for clients to handle both because of
the large amount of state that must be kept and because there may
be multiple messages in the responses. For these reasons it is
clarified here that a valid reason for not pipelining queries is
when they are all XFR queries i.e. clients sending multiple XFRs
MAY choose not to pipeline those queries. Clients that do not
pipeline XFR queries, therefore, have no additional requirements
to handle out-of-order or intermingled responses (as described
later) since they will never receive them.
o Implementations SHOULD use [RFC7828] (The edns-tcp-keepalive EDNS0
Option) to manage persistent connections.
Toorop, et al. Expires September 9, 2021 [Page 12]
Internet-Draft XFR-over-TLS March 2021
The following sections include detailed clarifications on the updates
to XFR behavior implied in [RFC7766] and how the use of [RFC7828]
applies specifically to XFR exchanges. It also discusses how IXFR
and AXFR can reuse the same TCP connection.
For completeness, we also mention here the recent specification of
extended DNS error (EDE) codes [RFC8914]. For zone transfers, when
returning REFUSED to a zone transfer request to an 'unauthorized'
client (e.g. where the client is not listed in an ACL for zone
transfers or does not sign the request with the correct TSIG key),
the extended DNS error code 18 (Prohibited) can also be sent.
6.1. Update to RFC1995 for IXFR-over-TCP
For clarity - an IXFR-over-TCP server compliant with this
specification MUST be able to handle multiple concurrent IXoT
requests on a single TCP connection (for the same and different
zones) and SHOULD send the responses as soon as they are available,
which might be out-of-order compared to the requests.
6.2. Update to RFC5936 for AXFR-over-TCP
For clarity - an AXFR-over-TCP server compliant with this
specification MUST be able to handle multiple concurrent AXoT
sessions on a single TCP connection (for the same and different
zones). The response streams for concurrent AXFRs MAY be
intermingled and AXFR-over-TCP clients compliant with this
specification which pipeline AXFR requests MUST be able to handle
this.
6.3. Updates to RFC1995 and RFC5936 for XFR-over-TCP
6.3.1. Connection reuse
As specified, XFR-over-TCP clients SHOULD re-use any existing open
TCP connection when starting any new XFR request to the same primary,
and for issuing SOA queries, instead of opening a new connection.
The number of TCP connections between a secondary and primary SHOULD
be minimized (also see Section 6.4).
Valid reasons for not re-using existing connections might include:
o as already noted in [RFC7766], separate connections for different
zones might be preferred for operational reasons. In this case
the number of concurrent connections for zone transfers SHOULD be
limited to the total number of zones transferred between the
client and server.
Toorop, et al. Expires September 9, 2021 [Page 13]
Internet-Draft XFR-over-TLS March 2021
o reaching a configured limit for the number of outstanding queries
or XFR requests allowed on a single TCP connection
o the message ID pool has already been exhausted on an open
connection
o a large number of timeouts or slow responses have occurred on an
open connection
o an edns-tcp-keepalive EDNS0 option with a timeout of 0 has been
received from the server and the client is in the process of
closing the connection (see Section 6.3.4)
If no TCP connections are currently open, XFR clients MAY send SOA
queries over UDP or a new TCP connection.
6.3.2. AXFRs and IXFRs on the same connection
Neither [RFC1995] nor [RFC5936] explicitly discuss the use of a
single TCP connection for both IXFR and AXFR requests. [RFC5936]
does make the general statement:
"Non-AXFR session traffic can also use an open TCP connection."
We clarify here that implementations capable of both AXFR and IXFR
and compliant with this specification SHOULD
o use the same TCP connection for both AXFR and IXFR requests to the
same primary
o pipeline such requests (if they pipeline XFR requests in general)
and MAY intermingle them
o send the response(s) for each request as soon as they are
available i.e. responses MAY be sent intermingled
6.3.3. XFR limits
The server MAY limit the number of concurrent IXFRs, AXFRs or total
XFR transfers in progress, or from a given secondary, to protect
server resources. Servers SHOULD return SERVFAIL if this limit is
hit, since it is a transient error and a retry at a later time might
succeed.
Toorop, et al. Expires September 9, 2021 [Page 14]
Internet-Draft XFR-over-TLS March 2021
6.3.4. The edns-tcp-keepalive EDNS0 Option
XFR clients that send the edns-tcp-keepalive EDNS0 option on every
XFR request provide the server with maximum opportunity to update the
edns-tcp-keepalive timeout. The XFR server may use the frequency of
recent XFRs to calculate an average update rate as input to the
decision of what edns-tcp-keepalive timeout to use. If the server
does not support edns-tcp-keepalive the client MAY keep the
connection open for a few seconds ([RFC7766] recommends that servers
use timeouts of at least a few seconds).
Whilst the specification for EDNS0 [RFC6891] does not specifically
mention AXFRs, it does say
"If an OPT record is present in a received request, compliant
responders MUST include an OPT record in their respective
responses."
We clarify here that if an OPT record is present in a received AXFR
request, compliant responders MUST include an OPT record in each of
the subsequent AXFR responses. Note that this requirement, combined
with the use of edns-tcp-keepalive, enables AXFR servers to signal
the desire to close a connection (when existing transactions have
competed) due to low resources by sending an edns-tcp-keepalive EDNS0
option with a timeout of 0 on any AXFR response. This does not
signal that the AXFR is aborted, just that the server wishes to close
the connection as soon as possible.
6.3.5. Backwards compatibility
Certain legacy behaviors were noted in [RFC5936], with provisions
that implementations may want to offer options to fallback to legacy
behavior when interoperating with servers known not to support
[RFC5936]. For purposes of interoperability, IXFR and AXFR
implementations may want to continue offering such configuration
options, as well as supporting some behaviors that were
underspecified prior to this work (e.g. performing IXFR and AXFRs on
separate connections). However, XoT implementations should have no
need to do so.
6.4. Update to RFC7766
[RFC7766] made general implementation recommendations with regard to
TCP/TLS connection handling:
Toorop, et al. Expires September 9, 2021 [Page 15]
Internet-Draft XFR-over-TLS March 2021
"To mitigate the risk of unintentional server overload, DNS
clients MUST take care to minimize the number of concurrent TCP
connections made to any individual server. It is RECOMMENDED
that for any given client/server interaction there SHOULD be no
more than one connection for regular queries, one for zone
transfers, and one for each protocol that is being used on top
of TCP (for example, if the resolver was using TLS). However,
it is noted that certain primary/ secondary configurations with
many busy zones might need to use more than one TCP connection
for zone transfers for operational reasons (for example, to
support concurrent transfers of multiple zones)."
Whilst this recommends a particular behavior for the clients using
TCP, it does not relax the requirement for servers to handle 'mixed'
traffic (regular queries and zone transfers) on any open TCP/TLS
connection. It also overlooks the potential that other transports
might want to take the same approach with regard to using separate
connections for different purposes.
This specification for XoT updates the guidance in [RFC7766] to
provide the same separation of connection purpose (regular queries
and zone transfers) for all transports being used on top of TCP.
Therefore, it is RECOMMENDED that for each protocol used on top of
TCP in any given client/server interaction there SHOULD be no more
than one connection for regular queries and one for zone transfers.
As an illustration, it could be imagined that in future such an
interaction could hypothetically include one or all of the following:
o one TCP connection for regular queries
o one TCP connection for zone transfers
o one TLS connection for regular queries
o one TLS connection for zone transfers
o one DoH connection for regular queries
o one DoH connection for zone transfers
Section 6.3.1 has provided specific details of reasons where more
than one connection for a given transport might be required for zone
transfers from a particular client.
Toorop, et al. Expires September 9, 2021 [Page 16]
Internet-Draft XFR-over-TLS March 2021
7. XoT specification
7.1. TLS versions
For improved security all implementations of this specification MUST
use only TLS 1.3 [RFC8446] or later.
7.2. Port selection
The connection for XoT SHOULD be established using port 853, as
specified in [RFC7858], unless there is mutual agreement between the
secondary and primary to use a port other than port 853 for XoT.
There MAY be agreement to use different ports for AXoT and IXoT, or
for different zones.
7.3. High level XoT descriptions
It is useful to note that in XoT it is the secondary that initiates
the TLS connection to the primary for a XFR request, so that in terms
of connectivity the secondary is the TLS client and the primary the
TLS server.
The figure below provides an outline of the AXoT mechanism including
NOTIFYs.
Toorop, et al. Expires September 9, 2021 [Page 17]
Internet-Draft XFR-over-TLS March 2021
Secondary Primary
| NOTIFY |
| <-------------------------------- | UDP
| --------------------------------> |
| NOTIFY Response |
| |
| |
| SOA Request |
| --------------------------------> | UDP (or part of
| <-------------------------------- | a TCP/TLS session)
| SOA Response |
| |
| |
| |
| AXFR Request | ---
| --------------------------------> | |
| <-------------------------------- | |
| AXFR Response 1 | |
| (Zone data) | |
| | |
| <-------------------------------- | | TLS
| AXFR Response 2 | | Session
| (Zone data) | |
| | |
| <-------------------------------- | |
| AXFR Response 3 | |
| (Zone data) | ---
| |
Figure 3. AXoT Mechanism
The figure below provides an outline of the IXoT mechanism including
NOTIFYs.
Toorop, et al. Expires September 9, 2021 [Page 18]
Internet-Draft XFR-over-TLS March 2021
Secondary Primary
| NOTIFY |
| <-------------------------------- | UDP
| --------------------------------> |
| NOTIFY Response |
| |
| |
| SOA Request |
| --------------------------------> | UDP (or part of
| <-------------------------------- | a TCP/TLS session)
| SOA Response |
| |
| |
| |
| IXFR Request | ---
| --------------------------------> | |
| <-------------------------------- | |
| IXFR Response | |
| (Zone data) | |
| | | TLS
| | | session
| IXFR Request | |
| --------------------------------> | |
| <-------------------------------- | |
| IXFR Response | |
| (Zone data) | ---
Figure 4. IXoT Mechanism
7.4. XoT transfers
For a zone transfer between two end points to be considered protected
with XoT all XFR requests and response for that zone MUST be sent
over TLS connections where at a minimum:
o the client MUST authenticate the server by use of an
authentication domain name using a Strict Privacy Profile as
described in [RFC8310]
o the server MUST validate the client is authorized to request or
proxy a zone transfer by using one or both of the following:
* an IP based ACL (which can be either per-message or per-
connection)
* Mutual TLS (mTLS)
Toorop, et al. Expires September 9, 2021 [Page 19]
Internet-Draft XFR-over-TLS March 2021
The server MAY also require a valid TSIG/SIG(0) signature, but this
alone is not sufficient to authenticate the client or server.
Authentication mechanisms are discussed in full in Section 9 and the
rationale for the above requirement in Section 10. Transfer group
policies are discussed in Section 11.
7.5. XoT connections
The details in Section 6 about e.g., persistent connections and XFR
message handling are fully applicable to XoT connections as well.
However any behavior specified here takes precedence for XoT.
If no TLS connections are currently open, XoT clients MAY send SOA
queries over UDP or TCP, or TLS.
7.6. XoT vs ADoT
As noted earlier, there is currently no specification for encryption
of connections from recursive resolvers to authoritative servers.
Some authoritatives are experimenting with ADoT and opportunistic
encryption has also been raised as a possibility; it is therefore
highly likely that use of encryption by authoritative servers will
evolve in the coming years.
This raises questions in the short term,S.S. with regard to TLS
connection and message handling for authoritative servers. In
particular, there is likely to be a class of authoritatives that wish
to use XoT in the near future with a small number of configured
secondaries but that do wish to support DoT for regular queries from
recursive in that same time frame. These servers have to potentially
cope with probing and direct queries from recursives and from test
servers, and also potential attacks that might wish to make use of
TLS to overload the server.
[RFC5936] clearly states that non-AXFR session traffic can use an
open TCP connection, however, this requirement needs to be re-
evaluated when considering applying the same model to XoT. Proposing
that a server should also start responding to all queries received
over TLS just because it has enabled XoT would be equivalent to
defining a form of authoritative DoT. This specification does not
propose that, but it also does not prohibit servers from answering
queries unrelated to XFR exchanges over TLS. Rather, this
specification simply outlines in later sections:
o how XoT implementations should utilize EDE codes in response to
queries on TLS connections they are not willing to answer (see
Section 7.7)
Toorop, et al. Expires September 9, 2021 [Page 20]
Internet-Draft XFR-over-TLS March 2021
o the operational and policy options that a XoT server operator has
with regard to managing TLS connections and messages (see
Appendix A)
7.7. Response RCODES
XoT clients and servers MUST implement EDE codes. If a XoT server
receives non-XoT traffic it is not willing to answer on a TLS
connection it SHOULD respond with the extended DNS error code 21 -
Not Supported [RFC8914]. XoT clients should not send any further
queries of this type to the server for a reasonable period of time
(for example, one hour) i.e., long enough that the server
configuration or policy might be updated.
Historically servers have used the REFUSED RCODE for many situations,
and so clients often had no detailed information on which to base an
error or fallback path when queries were refused. As a result the
client behavior could vary significantly. XoT servers that refuse
queries must cater for the fact that client behavior might vary from
continually retrying queries regardless of receiving REFUSED to every
query, or at the other extreme clients may decide to stop using the
server over any transport. This might be because those clients are
either non-XoT clients or do not implement EDE codes.
7.8. AXoT specifics
7.8.1. Padding AXoT responses
The goal of padding AXoT responses would be two fold:
o to obfuscate the actual size of the transferred zone to minimize
information leakage about the entire contents of the zone.
o to obfuscate the incremental changes to the zone between SOA
updates to minimize information leakage about zone update activity
and growth.
Note that the re-use of XoT connections for transfers of multiple
different zones complicates any attempt to analyze the traffic size
and timing to extract information.
It is noted here that, depending on the padding policies eventually
developed for XoT, the requirement to obfuscate the total zone size
might require a server to create 'empty' AXoT responses. That is,
AXoT responses that contain no RR's apart from an OPT RR containing
the EDNS(0) option for padding. For example, without this capability
the maximum size that a tiny zone could be padded to would
Toorop, et al. Expires September 9, 2021 [Page 21]
Internet-Draft XFR-over-TLS March 2021
theoretically be limited if there had to be a minimum of 1 RR per
packet.
However, as with existing AXFR, the last AXoT response message sent
MUST contain the same SOA that was in the first message of the AXoT
response series in order to signal the conclusion of the zone
transfer.
[RFC5936] says:
"Each AXFR response message SHOULD contain a sufficient number
of RRs to reasonably amortize the per-message overhead, up to
the largest number that will fit within a DNS message (taking
the required content of the other sections into account, as
described below)."
'Empty' AXoT responses generated in order to meet a padding
requirement will be exceptions to the above statement. For
flexibility, future proofing and in order to guarantee support for
future padding policies, we state here that secondary implementations
MUST be resilient to receiving padded AXoT responses, including
'empty' AXoT responses that contain only an OPT RR containing the
EDNS(0) option for padding.
Recommendation of specific policies for padding AXoT responses are
out of scope for this specification. Detailed considerations of such
policies and the trade-offs involved are expected to be the subject
of future work.
7.9. IXoT specifics
7.9.1. Condensation of responses
[RFC1995] says condensation of responses is optional and MAY be done.
Whilst it does add complexity to generating responses it can
significantly reduce the size of responses. However any such
reduction might be offset by increased message size due to padding.
This specification does not update the optionality of condensation
for XoT responses.
7.9.2. Fallback to AXFR
Fallback to AXFR can happen, for example, if the server is not able
to provide an IXFR for the requested SOA. Implementations differ in
how long they store zone deltas and how many may be stored at any one
time.
Toorop, et al. Expires September 9, 2021 [Page 22]
Internet-Draft XFR-over-TLS March 2021
Just as with IXFR-over-TCP, after a failed IXFR a IXoT client SHOULD
request the AXFR on the already open XoT connection.
7.9.3. Padding of IXoT responses
The goal of padding IXoT responses would be to obfuscate the
incremental changes to the zone between SOA updates to minimize
information leakage about zone update activity and growth. Both the
size and timing of the IXoT responses could reveal information.
IXFR responses can vary in size greatly from the order of 100 bytes
for one or two record updates, to tens of thousands of bytes for
large dynamic DNSSEC signed zones. The frequency of IXFR responses
can also depend greatly on if and how the zone is DNSSEC signed.
In order to guarantee support for future padding policies, we state
here that secondary implementations MUST be resilient to receiving
padded IXoT responses.
Recommendation of specific policies for padding IXoT responses are
out of scope for this specification. Detailed considerations of such
policies and the trade-offs involved are expected to be the subject
of future work.
7.10. Name compression and maximum payload sizes
It is noted here that name compression [RFC1035] can be used in XFR
responses to reduce the size of the payload, however the maximum
value of the offset that can be used in the name compression pointer
structure is 16384. For some DNS implementations this limits the
size of an individual XFR response used in practice to something
around the order of 16kB. In principle, larger payload sizes can be
supported for some responses with more sophisticated approaches (e.g.
by pre-calculating the maximum offset required).
Implementations may wish to offer options to disable name compression
for XoT responses to enable larger payloads. This might be
particularly helpful when padding is used since minimizing the
payload size is not necessarily a useful optimization in this case
and disabling name compression will reduce the resources required to
construct the payload.
8. Multi-primary Configurations
Also known as multi-master configurations this model can provide
flexibility and redundancy particularly for IXFR. A secondary will
receive one or more NOTIFY messages and can send an SOA to all of the
Toorop, et al. Expires September 9, 2021 [Page 23]
Internet-Draft XFR-over-TLS March 2021
configured primaries. It can then choose to send an XFR request to
the primary with the highest SOA (or other criteria, e.g., RTT).
When using persistent connections the secondary may have a XoT
connection already open to one or more primaries. Should a secondary
preferentially request an XFR from a primary to which it already has
an open XoT connection or the one with the highest SOA (assuming it
doesn't have a connection open to it already)?
Two extremes can be envisaged here. The first one can be considered
a 'preferred primary connection' model. In this case the secondary
continues to use one persistent connection to a single primary until
it has reason not to. Reasons not to might include the primary
repeatedly closing the connection, long RTTs on transfers or the SOA
of the primary being an unacceptable lag behind the SOA of an
alternative primary.
The other extreme can be considered a 'parallel primary connection'
model. Here a secondary could keep multiple persistent connections
open to all available primaries and only request XFRs from the
primary with the highest serial number. Since normally the number of
secondaries and primaries in direct contact in a transfer group is
reasonably low this might be feasible if latency is the most
significant concern.
Recommendation of a particular scheme is out of scope of this
document but implementations are encouraged to provide configuration
options that allow operators to make choices about this behavior.
9. Authentication mechanisms
To provide context to the requirements in section Section 7.4, this
section provides a brief summary of some of the existing
authentication and validation mechanisms (both transport independent
and TLS specific) that are available when performing zone transfers.
Section 10 then discusses in more details specifically how a
combination of TLS authentication, TSIG and IP based ACLs interact
for XoT.
We classify the mechanisms based on the following properties:
o 'Data Origin Authentication' (DO): Authentication that the DNS
message originated from the party with whom credentials were
shared, and of the data integrity of the message contents (the
originating party may or may not be party operating the far end of
a TCP/TLS connection in a 'proxy' scenario).
Toorop, et al. Expires September 9, 2021 [Page 24]
Internet-Draft XFR-over-TLS March 2021
o 'Channel Confidentiality' (CC): Confidentiality of the
communication channel between the client and server (i.e. the two
end points of a TCP/TLS connection) from passive surveillance.
o 'Channel Authentication' (CA): Authentication of the identity of
party to whom a TCP/TLS connection is made (this might not be a
direct connection between the primary and secondary in a proxy
scenario).
9.1. TSIG
TSIG [RFC8945] provides a mechanism for two or more parties to use
shared secret keys which can then be used to create a message digest
to protect individual DNS messages. This allows each party to
authenticate that a request or response (and the data in it) came
from the other party, even if it was transmitted over an unsecured
channel or via a proxy.
Properties: Data origin authentication
9.2. SIG(0)
SIG(0) [RFC2931] similarly also provides a mechanism to digitally
sign a DNS message but uses public key authentication, where the
public keys are stored in DNS as KEY RRs and a private key is stored
at the signer.
Properties: Data origin authentication
9.3. TLS
9.3.1. Opportunistic TLS
Opportunistic TLS for DoT is defined in [RFC8310] and can provide a
defense against passive surveillance, providing on-the-wire
confidentiality. Essentially
o clients that know authentication information for a server SHOULD
try to authenticate the server
o however they MAY fallback to using TLS without authentication and
o they MAY fallback to using cleartext if TLS is not available.
As such it does not offer a defense against active attacks (e.g. a
MitM attack on the connection from client to server), and is not
considered as useful for XoT.
Toorop, et al. Expires September 9, 2021 [Page 25]
Internet-Draft XFR-over-TLS March 2021
Properties: None guaranteed.
9.3.2. Strict TLS
Strict TLS for DoT [RFC8310] requires that a client is configured
with an authentication domain name (and/or SPKI pinset) that MUST be
used to authenticate the TLS handshake with the server. If
authentication of the server fails, the client will not proceed with
the connection. This provides a defense for the client against
active surveillance, providing client-to-server authentication and
end-to-end channel confidentiality.
Properties: Channel confidentiality and authentication (of the
server).
9.3.3. Mutual TLS
This is an extension to Strict TLS [RFC8310] which requires that a
client is configured with an authentication domain name (and/or SPKI
pinset) and a client certificate. The client offers the certificate
for authentication by the server and the client can authentic the
server the same way as in Strict TLS. This provides a defense for
both parties against active surveillance, providing bi-directional
authentication and end-to-end channel confidentiality.
Properties: Channel confidentiality and mutual authentication.
9.4. IP Based ACL on the Primary
Most DNS server implementations offer an option to configure an IP
based Access Control List (ACL), which is often used in combination
with TSIG based ACLs to restrict access to zone transfers on primary
servers on a per query basis.
This is also possible with XoT but it must be noted that, as with
TCP, the implementation of such an ACL cannot be enforced on the
primary until an XFR request is received on an established
connection.
As discussed in Appendix A an IP based per connection ACL could also
be implemented where only TLS connections from recognized secondaries
are accepted.
Properties: Channel authentication of the client.
Toorop, et al. Expires September 9, 2021 [Page 26]
Internet-Draft XFR-over-TLS March 2021
9.5. ZONEMD
For completeness, we also describe Message Digest for DNS Zones
(ZONEMD) [RFC8976] here. The message digest is a mechanism that can
be used to verify the content of a standalone zone. It is designed
to be independent of the transmission channel or mechanism, allowing
a general consumer of a zone to do origin authentication of the
entire zone contents. Note that the current version of [RFC8976]
states:
"As specified herein, ZONEMD is impractical for large, dynamic zones
due to the time and resources required for digest calculation.
However, The ZONEMD record is extensible so that new digest schemes
may be added in the future to support large, dynamic zones."
It is complementary but orthogonal the above mechanisms; and can be
used in conjunction with XoT but is not considered further here.
10. XoT authentication
It is noted that zone transfer scenarios can vary from a simple
single primary/secondary relationship where both servers are under
the control of a single operator to a complex hierarchical structure
which includes proxies and multiple operators. Each deployment
scenario will require specific analysis to determine which
combination of authentication methods are best suited to the
deployment model in question.
The XoT authentication requirement specified in Section 7.4 addresses
the issue of ensuring that the transfers is encrypted between the two
endpoints directly involved in the current transfers. The following
table summarized the properties of a selection of the mechanisms
discussed in Section 9. The two letter acronyms for the properties
are used below and (S) indicates the secondary and (P) indicates the
primary.
+----------------+-------+-------+-------+-------+-------+-------+
| Method | DO(S) | CC(S) | CA(S) | DO(P) | CC(P) | CA(P) |
+----------------+-------+-------+-------+-------+-------+-------+
| Strict TLS | | Y | Y | | Y | |
| Mutual TLS | | Y | Y | | Y | Y |
| ACL on primary | | | | | | Y |
| TSIG | Y | | | Y | | |
+----------------+-------+-------+-------+-------+-------+-------+
Table 1: Properties of Authentication methods for XoT
Based on this analysis it can be seen that:
Toorop, et al. Expires September 9, 2021 [Page 27]
Internet-Draft XFR-over-TLS March 2021
o Using just mutual TLS can be considered a standalone solution
since both end points are authenticated
o Using Strict TLS and an IP based ACL on the primary also provides
authentication of both end points
o Additional use of TSIG (or equally SIG(0)) can also provide data
origin authentication which might be desirable for deployments
that include a proxy between the secondary and primary, but is not
part of the XoT requirement because it does nothing to guarantee
channel confidentiality or authentication.
11. Policies for Both AXoT and IXoT
Whilst the protection of the zone contents in a transfer between two
end points can be provided by the XoT protocol, the protection of all
the transfers of a given zone requires operational administration and
policy management.
We call the entire group of servers involved in XFR for a particular
set of zones (all the primaries and all the secondaries) the
'transfer group'.
Within any transfer group both AXFRs and IXFRs for a zone MUST all
use the same policy, e.g., if AXFRs use AXoT all IXFRs MUST use IXoT.
In order to assure the confidentiality of the zone information, the
entire transfer group MUST have a consistent policy of requiring
confidentiality. If any do not, this is a weak link for attackers to
exploit.
An individual zone transfer is not considered protected by XoT unless
both the client and server are configured to use only XoT and the
overall zone transfer is not considered protected until all members
of the transfer group are configured to use only XoT with all other
transfers servers (see Section 12).
A XoT policy should specify
o What kind of TLS is required (Strict or Mutual TLS)
o or if an IP based ACL is required.
o (optionally) if TSIG/SIG(0) is required
Since this may require configuration of a number of servers who may
be under the control of different operators the desired consistency
could be hard to enforce and audit in practice.
Toorop, et al. Expires September 9, 2021 [Page 28]
Internet-Draft XFR-over-TLS March 2021
Certain aspects of the Policies can be relatively easily tested
independently, e.g., by requesting zone transfers without TSIG, from
unauthorized IP addresses or over cleartext DNS. Other aspects such
as if a secondary will accept data without a TSIG digest or if
secondaries are using Strict as opposed to Opportunistic TLS are more
challenging.
The mechanics of co-ordinating or enforcing such policies are out of
the scope of this document but may be the subject of future
operational guidance.
12. Implementation Considerations
Server implementations may want to also offer options that allow ACLs
on a zone to specify that a specific client can use either XoT or
TCP. This would allow for flexibility while clients are migrating to
XoT.
Client implementations may similarly want to offer options to cater
for the multi-primary case where the primaries are migrating to XoT.
Such configuration options MUST only be used in a 'migration mode'
though, and therefore should be used with care.
It is noted that use of a TLS proxy in front of the primary server is
a simple deployment solution that can enable server side XoT.
13. IANA Considerations
None.
14. Implementation Status
[THIS SECTION TO BE REMOVED BEFORE PUBLICATION] This section records
the status of known implementations of the protocol defined by this
specification at the time of posting of this Internet-Draft, and is
based on a proposal described in [RFC7942].
A summary of current behavior and implementation status can be found
here: XoT implementation status [1]
Specific recent activity includes:
1. The 1.9.2 version of Unbound [2] includes an option to perform
AXoT (instead of AXFR-over-TCP).
2. There are currently open pull requests against NSD to implement
Toorop, et al. Expires September 9, 2021 [Page 29]
Internet-Draft XFR-over-TLS March 2021
1. Connection re-use by default during XFR-over-TCP [3]
2. Client side XFR-over-TLS [4]
3. Version 9.17.7 of BIND contained an initial implementation of
DoT, implementation of XoT is planned for early 2021 [5]
Both items 1. and 2.2. listed above require the client (secondary) to
authenticate the server (primary) using a configured authentication
domain name if XoT is used.
15. Security Considerations
This document specifies a security measure against a DNS risk: the
risk that an attacker collects entire DNS zones through eavesdropping
on clear text DNS zone transfers.
This does not mitigate:
o the risk that some level of zone activity might be inferred by
observing zone transfer sizes and timing on encrypted connections
(even with padding applied), in combination with obtaining SOA
records by directly querying authoritative servers.
o the risk that hidden primaries might be inferred or identified via
observation of encrypted connections.
o the risk of zone contents being obtained via zone enumeration
techniques.
Security concerns of DoT are outlined in [RFC7858] and [RFC8310].
16. Acknowledgements
The authors thank Tony Finch, Benno Overeinder, Shumon Huque and Tim
Wicinski and many other members of DPRIVE for review and discussions.
The authors particularly thank Peter van Dijk, Ondrej Sury, Brian
Dickson and several other open source DNS implementers for valuable
discussion and clarification on the issue associated with pipelining
XFR queries and handling out-of-order/intermingled responses.
17. Contributors
Significant contributions to the document were made by:
Han Zhang
Salesforce
Toorop, et al. Expires September 9, 2021 [Page 30]
Internet-Draft XFR-over-TLS March 2021
San Francisco, CA
United States
Email: hzhang@salesforce.com
18. Changelog
draft-ietf-dprive-xfr-over-tls-08
o RFC2845 -> (obsoleted by) RFC8945
o I-D.ietf-dnsop-dns-zone-digest -> RFC8976
o Minor editorial changes + email update
draft-ietf-dprive-xfr-over-tls-07
o Reference RFC7942 in the implementation status section
o Convert the URIs that will remain on publication to references
o Correct typos in acknowledgments
draft-ietf-dprive-xfr-over-tls-06
o Update text relating to pipelining and connection reuse after WGLC
comments.
o Add link to implementation status matrix
o Various typos
draft-ietf-dprive-xfr-over-tls-05
o Remove the open questions that received no comments.
o Add more detail to the implementation section
draft-ietf-dprive-xfr-over-tls-04
o Add Github repository
o Fix typos and references and improve layout.
draft-ietf-dprive-xfr-over-tls-03
o Remove propose to use ALPN
Toorop, et al. Expires September 9, 2021 [Page 31]
Internet-Draft XFR-over-TLS March 2021
o Clarify updates to both RFC1995 and RFC5936 by adding specific
sections on this
o Add a section on the threat model
o Convert all SVG diagrams to ASCII art
o Add discussions on concurrency limits
o Add discussions on Extended DNS error codes
o Re-work authentication requirements and discussion
o Add appendix discussion TLS connection management
draft-ietf-dprive-xfr-over-tls-02
o Significantly update descriptions for both AXoT and IXoT for
message and connection handling taking into account previous
specifications in more detail
o Add use of APLN and limitations on traffic on XoT connections.
o Add new discussions of padding for both AXoT and IXoT
o Add text on SIG(0)
o Update security considerations
o Move multi-primary considerations to earlier as they are related
to connection handling
draft-ietf-dprive-xfr-over-tls-01
o Minor editorial updates
o Add requirement for TLS 1.3. or later
draft-ietf-dprive-xfr-over-tls-00
o Rename after adoption and reference update.
o Add placeholder for SIG(0) discussion
o Update section on ZONEMD
draft-hzpa-dprive-xfr-over-tls-02
Toorop, et al. Expires September 9, 2021 [Page 32]
Internet-Draft XFR-over-TLS March 2021
o Substantial re-work of the document.
draft-hzpa-dprive-xfr-over-tls-01
o Editorial changes, updates to references.
draft-hzpa-dprive-xfr-over-tls-00
o Initial commit
19. References
19.1. Normative References
[RFC1034] Mockapetris, P., "Domain names - concepts and facilities",
STD 13, RFC 1034, DOI 10.17487/RFC1034, November 1987,
<https://www.rfc-editor.org/info/rfc1034>.
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, DOI 10.17487/RFC1035,
November 1987, <https://www.rfc-editor.org/info/rfc1035>.
[RFC1995] Ohta, M., "Incremental Zone Transfer in DNS", RFC 1995,
DOI 10.17487/RFC1995, August 1996, <https://www.rfc-
editor.org/info/rfc1995>.
[RFC1996] Vixie, P., "A Mechanism for Prompt Notification of Zone
Changes (DNS NOTIFY)", RFC 1996, DOI 10.17487/RFC1996,
August 1996, <https://www.rfc-editor.org/info/rfc1996>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
editor.org/info/rfc2119>.
[RFC5936] Lewis, E. and A. Hoenes, Ed., "DNS Zone Transfer Protocol
(AXFR)", RFC 5936, DOI 10.17487/RFC5936, June 2010,
<https://www.rfc-editor.org/info/rfc5936>.
[RFC6973] Cooper, A., Tschofenig, H., Aboba, B., Peterson, J.,
Morris, J., Hansen, M., and R. Smith, "Privacy
Considerations for Internet Protocols", RFC 6973,
DOI 10.17487/RFC6973, July 2013, <https://www.rfc-
editor.org/info/rfc6973>.
[RFC7626] Bortzmeyer, S., "DNS Privacy Considerations", RFC 7626,
DOI 10.17487/RFC7626, August 2015, <https://www.rfc-
editor.org/info/rfc7626>.
Toorop, et al. Expires September 9, 2021 [Page 33]
Internet-Draft XFR-over-TLS March 2021
[RFC7766] Dickinson, J., Dickinson, S., Bellis, R., Mankin, A., and
D. Wessels, "DNS Transport over TCP - Implementation
Requirements", RFC 7766, DOI 10.17487/RFC7766, March 2016,
<https://www.rfc-editor.org/info/rfc7766>.
[RFC7828] Wouters, P., Abley, J., Dickinson, S., and R. Bellis, "The
edns-tcp-keepalive EDNS0 Option", RFC 7828,
DOI 10.17487/RFC7828, April 2016, <https://www.rfc-
editor.org/info/rfc7828>.
[RFC7858] Hu, Z., Zhu, L., Heidemann, J., Mankin, A., Wessels, D.,
and P. Hoffman, "Specification for DNS over Transport
Layer Security (TLS)", RFC 7858, DOI 10.17487/RFC7858, May
2016, <https://www.rfc-editor.org/info/rfc7858>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8310] Dickinson, S., Gillmor, D., and T. Reddy, "Usage Profiles
for DNS over TLS and DNS over DTLS", RFC 8310,
DOI 10.17487/RFC8310, March 2018, <https://www.rfc-
editor.org/info/rfc8310>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/rfc8446>.
[RFC8499] Hoffman, P., Sullivan, A., and K. Fujiwara, "DNS
Terminology", BCP 219, RFC 8499, DOI 10.17487/RFC8499,
January 2019, <https://www.rfc-editor.org/info/rfc8499>.
[RFC8914] Kumari, W., Hunt, E., Arends, R., Hardaker, W., and D.
Lawrence, "Extended DNS Errors", RFC 8914,
DOI 10.17487/RFC8914, October 2020, <https://www.rfc-
editor.org/info/rfc8914>.
[RFC8945] Dupont, F., Morris, S., Vixie, P., Eastlake 3rd, D.,
Gudmundsson, O., and B. Wellington, "Secret Key
Transaction Authentication for DNS (TSIG)", STD 93,
RFC 8945, DOI 10.17487/RFC8945, November 2020,
<https://www.rfc-editor.org/info/rfc8945>.
19.2. Informative References
[BIND] ISC, "BIND 9", 2021, <https://www.isc.org/bind/>.
Toorop, et al. Expires September 9, 2021 [Page 34]
Internet-Draft XFR-over-TLS March 2021
[I-D.ietf-dprive-dnsoquic]
Huitema, C., Mankin, A., and S. Dickinson, "Specification
of DNS over Dedicated QUIC Connections", draft-ietf-
dprive-dnsoquic-01 (work in progress), October 2020.
[I-D.ietf-dprive-phase2-requirements]
Livingood, J., Mayrhofer, A., and B. Overeinder, "DNS
Privacy Requirements for Exchanges between Recursive
Resolvers and Authoritative Servers", draft-ietf-dprive-
phase2-requirements-02 (work in progress), November 2020.
[I-D.ietf-tls-esni]
Rescorla, E., Oku, K., Sullivan, N., and C. Wood, "TLS
Encrypted Client Hello", draft-ietf-tls-esni-09 (work in
progress), December 2020.
[I-D.vandijk-dprive-ds-dot-signal-and-pin]
Dijk, P., Geuze, R., and E. Bretelle, "Signalling
Authoritative DoT support in DS records, with key
pinning", draft-vandijk-dprive-ds-dot-signal-and-pin-01
(work in progress), July 2020.
[I-D.vcelak-nsec5]
Vcelak, J., Goldberg, S., Papadopoulos, D., Huque, S., and
D. Lawrence, "NSEC5, DNSSEC Authenticated Denial of
Existence", draft-vcelak-nsec5-08 (work in progress),
December 2018.
[nist-guide]
Chandramouli, R. and S. Rose, "Secure Domain Name System
(DNS) Deployment Guide", 2013,
<https://nvlpubs.nist.gov/nistpubs/SpecialPublications/
NIST.SP.800-81-2.pdf>.
[NSD] NLnet Labs, "NSD", 2021,
<https://www.nlnetlabs.nl/projects/nsd/about/>.
[RFC1982] Elz, R. and R. Bush, "Serial Number Arithmetic", RFC 1982,
DOI 10.17487/RFC1982, August 1996, <https://www.rfc-
editor.org/info/rfc1982>.
[RFC2931] Eastlake 3rd, D., "DNS Request and Transaction Signatures
( SIG(0)s )", RFC 2931, DOI 10.17487/RFC2931, September
2000, <https://www.rfc-editor.org/info/rfc2931>.
Toorop, et al. Expires September 9, 2021 [Page 35]
Internet-Draft XFR-over-TLS March 2021
[RFC5155] Laurie, B., Sisson, G., Arends, R., and D. Blacka, "DNS
Security (DNSSEC) Hashed Authenticated Denial of
Existence", RFC 5155, DOI 10.17487/RFC5155, March 2008,
<https://www.rfc-editor.org/info/rfc5155>.
[RFC6891] Damas, J., Graff, M., and P. Vixie, "Extension Mechanisms
for DNS (EDNS(0))", STD 75, RFC 6891,
DOI 10.17487/RFC6891, April 2013, <https://www.rfc-
editor.org/info/rfc6891>.
[RFC7942] Sheffer, Y. and A. Farrel, "Improving Awareness of Running
Code: The Implementation Status Section", BCP 205,
RFC 7942, DOI 10.17487/RFC7942, July 2016,
<https://www.rfc-editor.org/info/rfc7942>.
[RFC8484] Hoffman, P. and P. McManus, "DNS Queries over HTTPS
(DoH)", RFC 8484, DOI 10.17487/RFC8484, October 2018,
<https://www.rfc-editor.org/info/rfc8484>.
[RFC8976] Wessels, D., Barber, P., Weinberg, M., Kumari, W., and W.
Hardaker, "Message Digest for DNS Zones", RFC 8976,
DOI 10.17487/RFC8976, February 2021, <https://www.rfc-
editor.org/info/rfc8976>.
19.3. URIs
[1] https://dnsprivacy.org/wiki/display/DP/
DNS+Privacy+Implementation+Status#DNSPrivacyImplementationStatus-
XFR/XoTImplementationstatus
[2] https://github.com/NLnetLabs/unbound/blob/release-1.9.2/doc/
Changelog
[3] https://github.com/NLnetLabs/nsd/pull/145
[4] https://github.com/NLnetLabs/nsd/pull/149
[5] https://gitlab.isc.org/isc-projects/bind9/-/issues/1784
Appendix A. XoT server connection handling
For completeness, it is noted that an earlier version of the
specification suggested using a XoT specific ALPN to negotiate TLS
connections that supported only a limited set of queries (SOA, XRFs)
however this did not gain support. Reasons given included additional
code complexity and proxies having no natural way to forward the ALPN
signal to DNS nameservers over TCP connections.
Toorop, et al. Expires September 9, 2021 [Page 36]
Internet-Draft XFR-over-TLS March 2021
A.1. Only listen on TLS on a specific IP address
Obviously a nameserver which hosts a zone and services queries for
the zone on an IP address published in an NS record may wish to use a
separate IP address for listening on TLS for XoT, only publishing
that address to its secondaries.
Pros: Probing of the public IP address will show no support for TLS.
ACLs will prevent zone transfer on all transports on a per query
basis.
Cons: Attackers passively observing traffic will still be able to
observe TLS connections to the separate address.
A.2. Client specific TLS acceptance
Primaries that include IP based ACLs and/or mutual TLS in their
authentication models have the option of only accepting TLS
connections from authorized clients. This could be implemented using
a proxy or directly in DNS implementation.
Pros: Connection management happens at setup time. The maximum
number of TLS connections a server will have to support can be easily
assessed. Once the connection is accepted the server might well be
willing to answer any query on that connection since it is coming
from a configured secondary and a specific response policy on the
connection may not be needed (see below).
Cons: Currently, none of the major open source DNS authoritative
implementations support such an option.
A.3. SNI based TLS acceptance
Primaries could also choose to only accept TLS connections based on
an SNI that was published only to their secondaries.
Pros: Reduces the number of accepted connections.
Cons: As above. For SNIs sent in the clear, this would still allow
attackers passively observing traffic to potentially abuse this
mechanism. The use of Encrypted Client Hello [I-D.ietf-tls-esni] may
be of use here.
A.4. TLS specific response policies
Some primaries might rely on TSIG/SIG(0) combined with per-query IP
based ACLs to authenticate secondaries. In this case the primary
Toorop, et al. Expires September 9, 2021 [Page 37]
Internet-Draft XFR-over-TLS March 2021
must accept all incoming TLS connections and then apply a TLS
specific response policy on a per query basis.
As an aside, whilst [RFC7766] makes a general purpose distinction to
clients in the usage of connections (between regular queries and zone
transfers) this is not strict and nothing in the DNS protocol
prevents using the same connection for both types of traffic. Hence
a server cannot know the intention of any client that connects to it,
it can only inspect the messages it receives on such a connection and
make per query decisions about whether or not to answer those
queries.
Example policies a XoT server might implement are:
o strict: REFUSE all queries on TLS connections except SOA and
authorized XFR requests
o moderate: REFUSE all queries on TLS connections until one is
received that is signed by a recognized TSIG/SIG(0) key, then
answer all queries on the connection after that
o complex: apply a heuristic to determine which queries on a TLS
connections to REFUSE
o relaxed: answer all non-XoT queries on all TLS connections with
the same policy applied to TCP queries
Pros: Allows for flexible behavior by the server that could be
changed over time.
Cons: The server must handle the burden of accepting all TLS
connections just to perform XFRs with a small number of secondaries.
Client behavior to REFUSED response is not clearly defined (see
below). Currently, none of the major open source DNS authoritative
implementations offer an option for different response policies in
different transports (but could potentially be implemented using a
proxy).
A.4.1. SNI based response policies
In a similar fashion, XoT servers might use the presence of an SNI in
the client hello to determine which response policy to initially
apply to the TLS connections.
Pros: This has to potential to allow a clean distinction between a
XoT service and any future DoT based service for answering recursive
queries.
Toorop, et al. Expires September 9, 2021 [Page 38]
Internet-Draft XFR-over-TLS March 2021
Cons: As above.
Authors' Addresses
Willem Toorop
NLnet Labs
Science Park 400
Amsterdam 1098 XH
The Netherlands
Email: willem@nlnetlabs.nl
Sara Dickinson
Sinodun IT
Magdalen Centre
Oxford Science Park
Oxford OX4 4GA
United Kingdom
Email: sara@sinodun.com
Shivan Sahib
Salesforce
Vancouver, BC
Canada
Email: shivankaulsahib@gmail.com
Pallavi Aras
Salesforce
Herndon, VA
United States
Email: paras@salesforce.com
Allison Mankin
Salesforce
Herndon, VA
United States
Email: allison.mankin@gmail.com
Toorop, et al. Expires September 9, 2021 [Page 39]