DRINKS J-F. Mule
Internet-Draft CableLabs
Intended status: Standards Track K. Cartwright
Expires: April 25, 2011 TNS
S. Ali
NeuStar
A. Mayrhofer
enum.at GmbH
October 22, 2010
Session Peering Provisioning Protocol
draft-ietf-drinks-spprov-03
Abstract
This document defines a protocol for provisioning session
establishment data into Session Data Registries and SIP Service
Provider data stores. The provisioned data is typically used by
various network elements for session peering.
This document describes the Session Peering Provisioning Protocol
used by clients to provision registries. The document provides a set
of guiding principles for the design of this protocol including
extensibility and independent transport definitions, a basic data
model and an XML Schema Document.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 25, 2011.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
Mule, et al. Expires April 25, 2011 [Page 1]
Internet-Draft draft-drinks-spprov October 2010
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Protocol High Level Design . . . . . . . . . . . . . . . . . . 9
3.1. Protocol Layering . . . . . . . . . . . . . . . . . . . . 9
3.2. Protocol Data Model . . . . . . . . . . . . . . . . . . . 10
4. Transport Protocol Requirements . . . . . . . . . . . . . . . 14
4.1. Connection Oriented . . . . . . . . . . . . . . . . . . . 15
4.2. Request and Response Model . . . . . . . . . . . . . . . . 15
4.3. Connection Lifetime . . . . . . . . . . . . . . . . . . . 15
4.4. Authentication . . . . . . . . . . . . . . . . . . . . . . 15
4.5. Confidentiality and Integrity . . . . . . . . . . . . . . 16
4.6. Near Real Time . . . . . . . . . . . . . . . . . . . . . . 16
4.7. Request and Response Sizes . . . . . . . . . . . . . . . . 16
4.8. Request and Response Correlation . . . . . . . . . . . . . 16
4.9. Request Acknowledgement . . . . . . . . . . . . . . . . . 16
4.10. Mandatory Transport . . . . . . . . . . . . . . . . . . . 17
5. Base Protocol Data Structures . . . . . . . . . . . . . . . . 18
5.1. Request and Response Structures . . . . . . . . . . . . . 18
5.1.1. Update Request and Response Structures . . . . . . . . 18
5.1.2. Query Request and Response Structures . . . . . . . . 21
5.2. Response Codes and Messages . . . . . . . . . . . . . . . 23
5.3. Basic Object Type and Organization Identifiers . . . . . . 25
6. Protocol Commands . . . . . . . . . . . . . . . . . . . . . . 27
6.1. Add Route Group Operation . . . . . . . . . . . . . . . . 27
6.2. Get Route Groups Operation . . . . . . . . . . . . . . . . 31
6.3. Add Destination Group Operation . . . . . . . . . . . . . 32
6.4. Get Destination Groups Operation . . . . . . . . . . . . . 33
6.5. Add Route Group Offer Operation . . . . . . . . . . . . . 34
6.6. Accept Route Group Offer Operation . . . . . . . . . . . . 36
6.7. Reject Route Group Offer Operation . . . . . . . . . . . . 37
6.8. Get Route Group Offers Operation . . . . . . . . . . . . . 38
6.9. Public Identifier Operations . . . . . . . . . . . . . . . 40
6.10. Egress Route Operations . . . . . . . . . . . . . . . . . 45
6.11. Add Route Record Operation . . . . . . . . . . . . . . . . 47
6.12. Get Route Records Operation . . . . . . . . . . . . . . . 52
Mule, et al. Expires April 25, 2011 [Page 2]
Internet-Draft draft-drinks-spprov October 2010
6.13. Delete Operation . . . . . . . . . . . . . . . . . . . . . 53
7. SPPP Examples . . . . . . . . . . . . . . . . . . . . . . . . 54
7.1. Add Destination Group . . . . . . . . . . . . . . . . . . 54
7.2. Add Route Records . . . . . . . . . . . . . . . . . . . . 55
7.3. Add Route Records -- URIType . . . . . . . . . . . . . . . 56
7.4. Add Route Group . . . . . . . . . . . . . . . . . . . . . 57
7.5. Add Public Identity -- Successful COR claim . . . . . . . 59
7.6. Add LRN . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.7. Add TN Range . . . . . . . . . . . . . . . . . . . . . . . 61
7.8. Add TN Range with Open Number Plan support . . . . . . . . 62
7.9. Add TN Prefix . . . . . . . . . . . . . . . . . . . . . . 63
7.10. Enable Peering -- Route Group Offer . . . . . . . . . . . 64
7.11. Enable Peering -- Route Group Offer Accept . . . . . . . . 66
7.12. Add Egress Route . . . . . . . . . . . . . . . . . . . . . 67
7.13. Get Destination Group . . . . . . . . . . . . . . . . . . 68
7.14. Get Public Identity . . . . . . . . . . . . . . . . . . . 69
7.15. Get Route Group Request . . . . . . . . . . . . . . . . . 70
7.16. Get Route Group Offers Request . . . . . . . . . . . . . . 71
7.17. Get Egree Route . . . . . . . . . . . . . . . . . . . . . 72
7.18. Delete Destination Group . . . . . . . . . . . . . . . . . 74
7.19. Delete Public Identity . . . . . . . . . . . . . . . . . . 74
7.20. Delete Route Group Request . . . . . . . . . . . . . . . . 75
7.21. Delete Route Group Offers Request . . . . . . . . . . . . 76
7.22. Delete Egress Route . . . . . . . . . . . . . . . . . . . 77
8. XML Considerations . . . . . . . . . . . . . . . . . . . . . . 79
8.1. Namespaces . . . . . . . . . . . . . . . . . . . . . . . . 79
8.2. Versioning and Character Encoding . . . . . . . . . . . . 79
9. Security Considerations . . . . . . . . . . . . . . . . . . . 80
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 81
11. Formal Specification . . . . . . . . . . . . . . . . . . . . . 82
12. Specification Extensibility . . . . . . . . . . . . . . . . . 95
13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 96
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 97
14.1. Normative References . . . . . . . . . . . . . . . . . . . 97
14.2. Informative References . . . . . . . . . . . . . . . . . . 97
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 99
Mule, et al. Expires April 25, 2011 [Page 3]
Internet-Draft draft-drinks-spprov October 2010
1. Introduction
Service providers and enterprises use registries to make call or
session routing decisions for Voice over IP, SMS and MMS traffic
exchanges. This document is narrowly focused on the provisioning
protocol for these registries. This protocol prescribes a way for an
entity to provision session-related data into a registry. The data
being provisioned can be optionally shared with other participating
peering entities. The requirements and use cases driving this
protocol have been documented in
[I-D.ietf-drinks-usecases-requirements]. The reader is expected to
be familiar with the terminology defined in the previously mentioned
document.
Three types of provisioning flows have been described in the use case
document: client to registry provisioning, registry to local data
repository and registry-to-registry. This document addresses a
subset (client-to-registry provisioning) by defining a Session
Peering Provisioning Protocol (SPPP) for provisioning Session
Establishment Data (SED) into a Registry (arrow "1" in the figure
below). While the other "provisioning flows" are shown below as
separate message flows, no determination has been made for whether
one common baseline protocol could be used for all three, or whether
distinct protocols are required.
Mule, et al. Expires April 25, 2011 [Page 4]
Internet-Draft draft-drinks-spprov October 2010
*------------* *------------*
(1). Provisioning SED | | (3).Registry | |
-----------------------> | Registry |<------------->| Registry |
data into Registries| | to Registry | |
*------------* exchanges *------------*
/ \ \
/ \ \
/ \ \
/ \ v
/ \ ...
/ \
/ (2). \
/ Distributing \
/ SED \
V V
+----------+ +----------+
|Local Data| |Local Data|
|Repository| |Repository|
+----------+ +----------+
Three Registry Provisioning Flows
Figure 1
The data provisioned for session establishment is typically used by
various downstream SIP signaling systems to route a call to the next
hop associated with the called domain. These systems typically use a
local data store ("Local Data Repository") as their source of session
routing information. More specifically, the SED data is the set of
parameters that the outgoing signaling path border elements (SBEs)
need to initiate the session. See [RFC5486] for more details.
A "terminating" SIP Service Provider (SSP) provisions SED into the
registry to be selectively shared with other peer SSPs.
Subsequently, a Registry may distribute the provisioned data into
local Data Repositories used for look-up queries (identifier -> URI)
or for lookup and location resolution (identifier -> URI -> ingress
SBE of terminating SSP). In some cases, the Registry may
additionally offer a central query resolution service (not shown in
the above figure).
A key requirement for the SPPP protocol is to be able to accommodate
two basic deployment scenarios:
1. A Local Data Repository serves a Look-Up Function (LUF) to
determine the target domain to assist in call routing (as
described in [RFC5486]). In this case, the querying entity may
Mule, et al. Expires April 25, 2011 [Page 5]
Internet-Draft draft-drinks-spprov October 2010
use other means to perform the Location Routing Function (LRF)
which in turn helps determine the actual location of the
Signaling Function in that domain.
2. A Local Data Repository serves both a Look-Up function (LUF) and
Location Routing Function (LRF) to locate the SED data fully.
In terms of protocol design, SPPP protocol is agnostic to the
transport. This document includes the description of the data model
and the means to enable protocol operations within a request and
response structure. To encourage interoperability, the protocol
supports extensibility aspects.
Transport requirements are provided in this document to help with the
selection of the optimum transport mechanism.
([I-D.ietf-drinks-sppp-over-soap]) identifies a SOAP transport
mechanism for SPPP.
This document is organized as follows:
o Section 2 provides the terminology;
o Section 3 provides an overview of the SPPP protocol, including
the layering approach, functional entities and data model;
o Section 4 specifies requirements for SPPP transport protocols;
o Section 5 describes the base protocol data structures including
the request and response elements (Section 5.1), the response
codes and messages (Section 5.2) and the basic object type most
first class objects extend from;
o Section 6 and Section 7 describe the main protocol commands and
examples;
o Section 8 defines XML considerations that XML parsers must meet
to conform to this specification;
o Section 11 normatively defines the SPPP protocol using its XML
Schema Definition.
Mule, et al. Expires April 25, 2011 [Page 6]
Internet-Draft draft-drinks-spprov October 2010
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
This document reuses terms from [RFC3261], [RFC5486], use cases and
requirements documented in [I-D.ietf-drinks-usecases-requirements]
and the ENUM Validation Architecture [RFC4725].
In addition, this document specifies the following additional terms:
SPPP: Session Peering Provisioning Protocol, the protocol used to
provision data into a Registry (see arrow labeled "1." in Figure 1
of [I-D.ietf-drinks-usecases-requirements]). It is the primary
scope of this document.
SPDP: Session Peering Distribution Protocol, the protocol used to
distribute data to Local Data Repository (see arrow labeled "2."
in Figure 1 of [I-D.ietf-drinks-usecases-requirements]).
Client: An application that supports an SPPP Client; it is
sometimes referred to as a "Registry Client".
Registry: The Registry operates a master database of Session
Establishment Data for one or more Registrants.
A Registry acts as an SPPP Server.
Registrant: In this document, we extend the definition of a
Registrant based on [RFC4725]. The Registrant is the end-user,
the person or organization who is the "holder" of the Session
Establishment Data being provisioned into the Registry. For
example, in [I-D.ietf-drinks-usecases-requirements], a Registrant
is pictured as a SIP Service Provider in Figure 2.
A Registrant is identified by its name and an identifier in the
data model.
Mule, et al. Expires April 25, 2011 [Page 7]
Internet-Draft draft-drinks-spprov October 2010
Registrar: In this document, we also extend the definition of a
Registrar from [RFC4725]. A Registrar performs provisioning
operations on behalf of a Registrant by interacting with the
Registry, in our case via the SPPP protocol defined in this
document.
A Registrar is identified by its name and an identifier in the
data model.
Mule, et al. Expires April 25, 2011 [Page 8]
Internet-Draft draft-drinks-spprov October 2010
3. Protocol High Level Design
This section introduces the structure of the data model and provides
the information framework for the SPPP protocol. An overview of the
protocol operations is first provided with a typical deployment
scenario. The data model is then defined along with all the objects
manipulated by the protocol and their relationships.
3.1. Protocol Layering
SPPP is a simple request/reply protocol that allows a client
application to submit provisioning data and query requests to a
server. The SPPP data structures are designed to be protocol
agnostic. Concerns regarding encryption, non-repudiation, and
authentication are beyond the scope of this document. For more
details, please refer to the Transport Protocol Requirements section.
Layer Example
+-------------+ +-----------------------------+
(5) |Data Objects | | RteGrpType, etc. |
+-------------+ +-----------------------------+
| |
+-------------+ +-----------------------------+
(4) | Operations | | AddRteGrpRqstType, etc. |
+-------------+ +-----------------------------+
| |
+-------------+ +-----------------------------+
(3) | Message | | spppUpdateRequest, |
| | | spppUpdateResponse, |
| | | spppQueryRequest, |
| | | spppQueryResponse |
+-------------+ +-----------------------------+
| |
+-------------+ +-----------------------------+
(2) | Message | | HTTP, SOAP, None, etc. |
| Envelope | | |
+-------------+ +-----------------------------+
| |
+-------------+ +-----------------------------+
(1) | Transport | | TCP, TLS, BEEP, etc. |
| Protocol | | |
+-------------+ +-----------------------------+
SPPP Layering
Figure 2
Mule, et al. Expires April 25, 2011 [Page 9]
Internet-Draft draft-drinks-spprov October 2010
SPPP can be viewed as a set of layers that collectively define the
structure of an SPPP request and response. Layers 1 and 2, as
detailed below, are left to separate specifications to allow for
potentially multiple SPPP transport, envelope, and authentication
technologies. This document defines layers 3, 4, and 5 below.
1. The transport protocol layer provides a communication mechanism
between the client and server. SPPP can be layered over any
transport protocol that provides a set of basic requirements
defined in the Transport Protocol Requirements section.
2. The message envelope layer is optional, but can provide features
that are above the transport technology layer but below the
application messaging layer. Technologies such as HTTP and SOAP
are examples of messaging envelope technologies.
3. The message layer provides a simple, envelope-independent and
transport-independent, SPPP wrapper for SPPP request and response
messages.
4. The operation layer defines the set of base SPPP actions that can
be invoked for a given object data type using an SPPP message.
Operations are encoded using XML encoded actions and objects.
5. The data object layer defines the base set of SPPP data objects
that can be included in update operations or returned in
operation responses.
3.2. Protocol Data Model
The data model illustrated and described in Figure 3 defines the
logical objects and the relationships between these objects that the
SPPP protocol supports. SPPP defines the protocol operations through
which an SPPP Client populates a Registry with these logical objects.
Various clients belonging to different Registrars may use the
protocol for populating the Registry's data.
The logical structure presented below is consistent with the
terminology and requirements defined in
[I-D.ietf-drinks-usecases-requirements].
+-------------+ +------------------+
| all object | |Organization: |
| types | |orgId, |
+------+------+ |orgName, |
+------------>|extension |
| |
Mule, et al. Expires April 25, 2011 [Page 10]
Internet-Draft draft-drinks-spprov October 2010
All objects are | |
associated with 2 | |
Organizations to +------------------+
identify the ^
registrant and |A Route Group is
the registrar |associated with
|zero or more Peering
|Organizations
|
+--------+--------------+
|Route Group: | +-----[abstract]-+
| rantId, | | Route Record: |
| rarId, | | |
| rteGrpName, | | rrName, |
| destGrpRef, +------->| priority, |
| isInSvc, | | extension |
| rteRecRef, | | |
| peeringOrg, | +----------------+
| sourceIdent, | ^
| priority, | |
| extension | |Various types
+-----------------------+ |of Route
^ |Records...
| +------+------------...
| | | |
| +----+ +-------+ +----+
| | URI| | NAPTR | | NS |
+----------------+-----+ +----+ +-------+ +----+
|Destination |
|Group: | +----------[abstract]-+
| rantId, | |Public Identifier: |
| rarId, | | |
| dgName, | | rantId, |
| extension |<----+ rarId, |
+----------------------+ | publicIdentifier, |
| destGrpRef, |
| rteRec, |
| extension |
+---------------------+
^
|Various types
|of Public
|Identifiers...
+---------+-------+------------...
| | | |
+------+ +-----+ +-----+ +-----+
| TN | | TNP | | TNR | | RN |
+------+ +-----+ +-----+ +-----+
Mule, et al. Expires April 25, 2011 [Page 11]
Internet-Draft draft-drinks-spprov October 2010
SPPP Data Model
Figure 3
The objects and attributes that comprise the data model can be
described as follows (objects listed from the bottom up):
o Public Identifier:
A public identifier is a well known attribute that is used as the
key to perform lookup functions. For the purposes of this
document, a Public Identifier can be a telephone number, a range
of telephone numbers, a PSTN Routing Number (RN), or perhaps
another type of lookup key.
A Public Identifier is associated with a Destination Group to
create a logical grouping of Public Identifiers that share a
common set of Routes.
A TN Public Identifier may optionally be associated with zero or
more individual Route Records. This ability for a Public
Identifier to be directly associated with a set of Route Records
(e.g. target URI), as opposed to being associated with a
Destination Group, supports the use cases where the target URI
contains data specifically tailored to an individual TN Public
Identifier.
o Telephone Number Range:
A public identifier may represent an inclusive range of telephone
numbers. The TN range is defined by the first and last telephone
number of the inclusive range. For example, a TN range defined by
tn=12125550000 and endTn=12125560000 means all the TNs from
12125550000 to 12125560000 inclusive are included.
o Destination Group:
A name collection of zero or more Public Identifiers that can be
associated with one or more Route Groups for the purpose of
facilitating the management of thier common routing information.
o Route Group:
A Route Group contains a set of references to Route Records, a set
of Destination Group references, and a set of peering organization
identifiers. This is used to establishe a three part
relationships between a set of Public Identifiers and their common
routing information (SED), and the list of peering organizations
whose query responses may include that routing information in
their query responses. To support the use cases defined in
[I-D.ietf-drinks-usecases-requirements], this document defines the
following types of Route Records: NAPTRType, NSType, and URIType.
Mule, et al. Expires April 25, 2011 [Page 12]
Internet-Draft draft-drinks-spprov October 2010
The sourceIdent element within a Route Group, in concert with the
set of peering organization identifiers enables fine grained
source based routing. Further details about the Route Group and
source based routing refer to the definitions and descriptions of
the Route Group operations found later in this document.
o Route Record:
A Route Record contains the data that a resolution system returns
in response to a successful query for a Public Identifier. Route
Recoords are associated with a Route Group for SED that is not
specific to a Public Identifier.
To support the use cases defined in
[I-D.ietf-drinks-usecases-requirements], SPPP protocol defines
three type of Route Records: URIType, NAPTRType, and NSType.
These Route Records extend the abstract type RteRecType and
inherit the common attribute 'priority' that is meant for setting
precedence across the route records defined within a Route Group
in a protocol agnostic fashion.
o Organization:
An Organization is an entity that may fulfill any combination of
three roles: Registrant, Registrar, and Peering Organization. All
SPPP objects are associated with two organization identifiers to
identify each object's registrant and the registrar. A Route
Group object is also associated with a set of zero or more
organization identifiers that identify the peering organizations
whose query responses may include the routing information (SED)
defined in the Route Records within that Route Group.
Mule, et al. Expires April 25, 2011 [Page 13]
Internet-Draft draft-drinks-spprov October 2010
4. Transport Protocol Requirements
This section provides requirements for transport protocols suitable
for SPPP. More specifically, this section specifies the services,
features, and assumptions that SPPP delegates to the chosen transport
and envelope technologies.
Two different groups of use cases are specified in
[I-D.ietf-drinks-usecases-requirements]. One group of use cases
describes the provisioning of data by a client into a Registry
(Section 3.1 of the above referenced document), while the other group
describes the distribution of data into local data repositories
(Section 3.2). The current version of this document focuses on the
first set of use cases (client to registry provisioning).
These use cases may involve the provisioning of very small data sets
like the modification or update of a single public identifier. Other
provisioning operations may deal with huge datasets like the
"download" of a whole local number portability database to a
Registry.
As a result, a transport protocol for SPPP must be very flexible and
accommodate various sizes of data set sizes.
For the reasons outlined above, it is conceivable that provisioning
and distributing may use different transport protocols. This
document focuses on the provisioning protocol.
A few topics remain open for discussion:
o The ability to establish multiple connections between a client and
server may be desirable. If so, we may want to specify the
relation of transactions between the various connections.
o Pipelining of requests is required at the SPPP protocol layer. It
may have impacts at the transport level that need to be outlined.
o Scope: the current scope of this effort is based upon having a
connection oriented transport. Is there any need to support a
transport protocol with asynchronous operation?
o If it is required that responses arrive in the order of the
requests, this must be specified clearly.
Mule, et al. Expires April 25, 2011 [Page 14]
Internet-Draft draft-drinks-spprov October 2010
4.1. Connection Oriented
The SPPP protocol follows a model where a Client establishes a
connection to a Server in order to further exchange provisioning
transactions over such point-to-point connection. A transport
protocol for SPPP MUST therefore be connection oriented.
Note that the role of the "Client" and the "Server" only applies to
the connection, and those roles are not related in any way to the
type of entity that participates in a protocol exchange. For
example, a Registry might also include a "Client" when such a
Registry initiates a connection (for example, for data distribution
to SSP).
4.2. Request and Response Model
Provisioning operations in SPPP follow the request - response model,
where a transaction is initiated by a Client using a Request command,
and the Server responds to the Client by means of a Response.
Multiple subsequent request-response exchanges MAY be performed over
a single connection.
Therefore, a transport protocol for SPPP MUST follow the request-
response model by allowing a response to be sent to the request
initiator.
4.3. Connection Lifetime
Some use cases involve provisioning a single request to a network
element - connections supporting such provisioning requests might be
short-lived, and only established on demand.
Other use cases involve either provisioning a huge set of data, or a
constant stream of small updates, which would require long-lived
connections.
Therefore, a protocol suitable for SPPP SHOULD support short lived as
well as long lived connections.
4.4. Authentication
Many use cases require the Server to authenticate the Client, and
potentially also the Client to authenticate the Server. While
authentication of the Server by the Client is expected to be used
only to prevent impersonation of the Server, authentication of the
Client by the Server is expected to be used to identify and further
authorize the Client to certain resources on the Server.
Mule, et al. Expires April 25, 2011 [Page 15]
Internet-Draft draft-drinks-spprov October 2010
Therefore, an SPPP transport protocol MUST provide means for a Server
to authenticate and authorize a Client, and MAY provide means for
Clients to authenticate a Server.
However, SPPP transport SHOULD also allow for unauthenticated
connections.
4.5. Confidentiality and Integrity
Data that is transported over the protocol is deemed confidential.
Therefore, a transport protocol suitable for SPPP MUST ensure
confidentiality and integrity protection by providing encryption
capabilities.
Additionally, a DRINKS protocol MUST NOT use an unreliable lower-
layer transport protocol that does not provide confidentiality and
integrity protection.
4.6. Near Real Time
Many use cases require near real-time responses from the Server.
Therefore, a DRINKS transport protocol MUST support near-real-time
response to requests submitted by the Client.
4.7. Request and Response Sizes
SPPP covers a range of use cases - from cases where provisioning a
single public identifier will create very small request and response
sizes to cases where millions of data records are submitted or
retrieved in one transaction. Therefore, a transport protocol
suitable for SPPP MUST support a great variety of request and
response sizes.
A transport protocol MAY allow splitting large chunks of data into
several smaller chunks.
4.8. Request and Response Correlation
A transport protocol suitable for SPPP MUST allow responses to be
correlated with requests.
4.9. Request Acknowledgement
Data transported in the SPPP protocol is likely crucial for the
operation of the communication network that is being provisioned.
Failed transactions can lead to situations where a subset of public
identifiers (or even SSPs) might not be reachable, or situations
Mule, et al. Expires April 25, 2011 [Page 16]
Internet-Draft draft-drinks-spprov October 2010
where the provisioning state of the network is inconsistent.
Therefore, a transport protocol for SPPP MUST provide a Response for
each Request, so that a Client can identify whether a Request
succeeded or failed.
4.10. Mandatory Transport
As of this writing of this revision, one transport protocol proposal
has been provided in [I-D.ietf-drinks-sppp-over-soap].
This section will define a mandatory transport protocol to be
compliant with this RFC.
Mule, et al. Expires April 25, 2011 [Page 17]
Internet-Draft draft-drinks-spprov October 2010
5. Base Protocol Data Structures
SPPP uses a common model and a common set of data structures for most
of the supported operations and object types. This section describes
these common data structures.
5.1. Request and Response Structures
An SPPP client interacts with an SPPP server by using one of the
supported transport mechanisms to send one or more requests to the
server and receive corresponding replies from the server. There are
two generalized types of operations that an SPPP client can submit to
an SPPP server, updates and queries. The following two sub-sections
describe the generalized data structures that are used for each of
these two types of operations.
5.1.1. Update Request and Response Structures
An SPPP update request is wrapped within the <spppUpdateRequest>
element while an SPPP update response is wrapped within an
<spppUpdateResponse> element. The following two sub-sections
describe these two elements.
5.1.1.1. Update Request
An SPPP update request object is contained within the generic
<spppUpdateRequest> element.
<element name="spppUpdateRequest">
<complexType>
<sequence>
<element name="clientTransId" type="spppb:TransIdType"
minOccurs="0"/>
<element name="minorVer" type="spppb:MinorVerType"
minOccurs="0"/>
<element name="rqst" type="spppb:BasicRqstType"
maxOccurs="unbounded"/>
</sequence>
</complexType>
</element>
<simpleType name="TransIdType">
<restriction base="string"/>
</simpleType>
Mule, et al. Expires April 25, 2011 [Page 18]
Internet-Draft draft-drinks-spprov October 2010
<simpleType name="MinorVerType">
<restriction base="unsignedLong"/>
</simpleType>
The data elements within the <spppUpdateRequest> element are
described as follows:
o clientTransId: Zero or one client generated transaction ID that,
within the context of the SPPP client, identifies this request.
This value can be used at the discretion of the SPPP client to
track, log or correlate requests and their responses. This
value is also echoed back to the client in the SPPP update
response. An SPPP server will not check this value for
uniqueness.
o minorVer: Zero or one minor version identifier, indicating the
minor version of the SPPP API that the client is attempting to
use. This is used in conjunction with the major version
identifier in the XML namespace to identify the version of SPPP
that the client is using. If the element is not present, the
server assumes that the client is using the latest minor version
supported by the SPPP server for the given major version. The
versions supported by a given SPPP server can be retrieved by
the client using the SPPP server menu operation described later
in the document.
o rqst: One or more BasicRqstType objects. These are the actions
that the client is requesting the SPPP server perform. They are
processed by the SPPP server in the order in which they are
included in the request. And with respect to handling error
conditions, it is a matter of policy whether the objects are
processed in a "stop and rollback" fashion or in a "stop and
commit" fashion. In the "stop and rollback" scenario, the SPPP
server would stop processing BasicRqstType object instances in
the request at the first error and roll back any BasicRqstType
object instances that had already been processed for that update
request. In the "stop and commit" scenario the SPPP server
would stop processing BasicRqstType object instances in the
request at the first error but commit any BasicRqstType object
instances that had already been processed for that update
request.
All update request objects extend the base type BasicRqstType. This
base type is defined as follows:
Mule, et al. Expires April 25, 2011 [Page 19]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="BasicRqstType" abstract="true">
<sequence>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
The BasicRqstType object primarily acts as an abstract base type, and
its only data element is described as follows:
o ext: This is the standard extension element for this object.
Refer to the Extensibility section of this document for more
details.
5.1.1.2. Update Response
An SPPP update response object is contained within the generic
<spppUpdateResponse> element.
<element name="spppUpdateResponse">
<complexType>
<sequence>
<element name="overallResult" type="spppb:ResultCodeType"/>
<element name="rqstObjResult" type="spppb:RqstObjResultCodeType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="clientTransId" type="spppb:TransIdType"
minOccurs="0"/>
<element name="serverTransId" type="spppb:TransIdType"/>
</sequence>
</complexType>
</element>
<complexType name="ResultCodeType">
<sequence>
<element name="code" type="int"/>
<element name="msg" type="string"/>
</sequence>
</complexType>
<complexType name="RqstObjResultCodeType">
<complexContent>
<extension base="spppb:ResultCodeType">
<sequence>
<element name="rqstObj" type="spppb:BasicRqstType"/>
</sequence>
</extension>
Mule, et al. Expires April 25, 2011 [Page 20]
Internet-Draft draft-drinks-spprov October 2010
</complexContent>
</complexType>
An <spppUpdateResponse> contains the elements necessary for the SPPP
client to precisely determine the overal result of the request, and
if an error occurred, it provides information about the specific
object, data element, or condition caused the error.
The data elements within the SPPP update response are described as
follows:
o clientTransId: Zero or one client transaction ID. This value is
simply an echo of the client transaction ID that SPPP client
passed into the SPPP update request.
o serverTransId: Exactly one server transaction ID that identifies
this request for tracking purposes. This value is guaranteed to
be unique for a given SPPP server.
o overallResult: Exactly one response code and message pair that
explicitly identifies the result of the request. See the
Response Code section for further details.
o rqstObjResult: An optional response code, response message, and
BasicRqstObject triplet. This element will be present only if
an object level error condition occurs, and indicates exactly
which error condition occurred and exactly which request object
that was passed in caused the error condition. The contained
BasicRqstObject is simply an echo of the request object instance
that caused the error, while the response code and message
indicate the error condition for this object. See the Response
Code section for further details.
o ext: This is the standard extension element for this object.
Refer to the Extensibility section for more details.
5.1.2. Query Request and Response Structures
An SPPP query request is wrapped within the <spppQueryRequest>
element while an SPPP query response is wrapped within an
<spppQueryResponse> element. The following two sub-sections describe
these two element structures.
Mule, et al. Expires April 25, 2011 [Page 21]
Internet-Draft draft-drinks-spprov October 2010
5.1.2.1. Query Request
An SPPP query request object is contained within the generic
<spppQueryRequest> element.
<element name="spppQueryRequest">
<complexType>
<sequence>
<element name="minorVer" type="spppb:MinorVerType"
minOccurs="0"/>
<element name="rqst" type="spppb:BasicQueryRqstType"/>
</sequence>
</complexType>
</element>
The data elements within the <spppQueryRequest> element are described
as follows:
o minorVer: Zero or one minor version identifier, indicating the
minor version of the SPPP API that the client is attempting to
use. This is used in conjunction with the major version
identifier in the XML namespace to identify the version of SPPP
that the client is using. If the element is not present, the
server assumes that the client is using the latest minor version
supported by the SPPP server for the given major version. The
versions supported by a given SPPP server can be retrieved by
the client using the SPPP server menu operation described later
in the document.
o rqst: One BasicQueryRqstType objects. This is the query that
the client is requesting the SPPP server perform.
All query request objects extend the base type BasicQueryRqstType.
This base type is defined as follows:
<complexType name="BasicQueryRqstType" abstract="true">
<sequence>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
The BasicQueryRqstType object primarily acts as an abstract base
Mule, et al. Expires April 25, 2011 [Page 22]
Internet-Draft draft-drinks-spprov October 2010
type, and its only data element is described as follows:
o ext: This is the standard extension element for this object.
Refer to the Extensibility section of this document for more
details.
5.1.2.2. Query Response
An SPPP query response object is contained within the generic
<spppQueryResponse> element.
<element name="spppQueryResponse">
<complexType>
<sequence>
<element name="overallResult" type="spppb:ResultCodeType"/>
<element name="resultSet" type="spppb:BasicObjType"
minOccurs="0" maxOccurs=" unbounded"/>
</sequence>
</complexType>
</element>
An <spppQueryResponse> contains the elements necessary for the SPPP
client to precisely determine the overal result of the query, and if
an error occurred, exactly what condition caused the error.
The data elements within the SPPP query response are described as
follows:
o overallResult: Exactly one response code and message pair that
explicitly identifies the result of the request. See the
Response Code section for further details.
o resultSet: The set of zero or more objects that matched the
query criteria. If no objects matched the query criteria then
this result set MUST be empty and the overallResult value MUST
indicate success (if no matches are found for the query
criteria, the response is considered a success).
5.2. Response Codes and Messages
This section contains the listing of response codes and their
corresponding human-readable text.
The response code numbering scheme generally adheres to the theory
formalized in section 4.2.1 of [RFC5321]:
Mule, et al. Expires April 25, 2011 [Page 23]
Internet-Draft draft-drinks-spprov October 2010
o The first digit of the response code can only be 1 or 2: 1 = a
positive result, 2 = a negative result.
o The second digit of the response code indicates the category: 0
= Protocol Syntax, 1 = Implementation Specific Business Rule, 2
= Security, 3 = Server System.
o The third and fourth digits of the response code indicate the
individual message event within the category defines by the
first two digits.
The response codes are also categorized as to whether they are
overall response codes that may only be returned in the
"overallResult" data element in SPPP responses, of object level
response codes that may only be returned in the "rqstObjResult"
element of the SPPP responses.
+--------+--------------------------+-------------------------------+
| Result | Text | Overall or Object Level |
| Code | | |
+--------+--------------------------+-------------------------------+
| 1000 | Request Succeeded. | Overall Response Code |
| | | |
| 2001 | Request syntax invalid. | Overall Response Code |
| | | |
| 2002 | Request too large. | Overall Response Code |
| | | |
| 2003 | Version not supported. | Overall Response Code |
| | | |
| 2103 | Command invalid. | Overall Response Code |
| | | |
| 2301 | System temporarily | Overall Response Code |
| | unavailable. | |
| | | |
| 2302 | Unexpected internal | Overall Response Code |
| | system or server error. | |
| | | |
| 2104 | Attribute value invalid. | Object Level Response Code |
| | | |
| | AttrName:[AttributeName] | |
| | AttrVal:[AttributeValue] | |
| | | |
| 2105 | Object does not exist. | Object Level Response Code |
| | AttrName:[AttributeName] | |
| | AttrVal:[AttributeValue] | |
| | | |
Mule, et al. Expires April 25, 2011 [Page 24]
Internet-Draft draft-drinks-spprov October 2010
| 2106 | Object status or | Object Level Response Code |
| | ownership does not allow | |
| | for operation. | |
| | AttrName:[AttributeName] | |
| | AttrVal:[AttributeValue] | |
+--------+--------------------------+-------------------------------+
Table 1: Response Codes Numbering Scheme and Messages
Each of the object level response messages are "parameterized" with
the following parameters: "AttributeName" and "AttributeValue".
The use of these parameters MUST adhere to the following rules:
o All parameters within a response message are mandatory and MUST
be present.
o Any value provided for the "AttributeName" parameter MUST be an
exact XSD element name of the protocol data element that the
response message is referring to. For example, valid values for
"attribute name" are "dgName", "rteGrpName", "rteRec", etc.
o The value for "AttributeValue" MUST be the value of the data
element to which the preceding "AttributeName" refers.
o Result code 2104 SHOULD be used whenever an element value does
not adhere to data validation rules.
o Result codes 2104 and 2105 MUST NOT be used interchangeably.
Response code 2105 SHOULD be returned by an update operation
when the data element(s) used to uniquely identify a pre-
existing object do not exist. If the data elements used to
uniquely identify an object are malformed, then response code
2104 SHOULD be returned.
5.3. Basic Object Type and Organization Identifiers
This section introduces the basic object type that most first class
objects derive from.
All first class objects extend the basic object type BasicObjType
which contains the identifier of the registrant organization that
owns this object, the identifier of the registrar organization that
provisioned this object, the date and time that the object was
created by the server, and the date and time that the object was last
modified.
Mule, et al. Expires April 25, 2011 [Page 25]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="BasicObjType" abstract="true">
<sequence>
<element name="rantId" type="spppb:OrgIdType"/>
<element name="rarId" type="spppb:OrgIdType"/>
<element name="crtDate" type="dateTime" minOccurs="0"/>
<element name="modDate" type="dateTime" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
The identifiers used for registrants (rantId), registrars (rarId) and
peering organizations (peeringOrg) are instances of OrgIdType. The
OrgIdType is defined as a string and all OrgIdType instances SHOULD
follow the textual convention: "namespace:value" (for example "iana-
en:32473"). See the IANA Consideration section for more details.
Mule, et al. Expires April 25, 2011 [Page 26]
Internet-Draft draft-drinks-spprov October 2010
6. Protocol Commands
This section provides a description of each supported protocol
command.
6.1. Add Route Group Operation
As described in the introductory sections, a Route Group represents a
combined grouping of Route Records that define route information,
Destination Groups that contain a set of Public Identifiers with
common routing information, and the list of peer organizations that
have access to these public identifiers using this route information.
It is this indirect linking of public identifiers to their route
information that significantly improves the scalability and
manageability of the peering data. Additions and changes to routing
information are reduced to a single operation on a Route Group or
Route Record , rather than millions of data updates to individual
public identifier records that individually contain their peering
data.
The AddRteGrpRqstType operation creates or overwrites a Route Group
object. If a Route Group with the given name and registrant ID
(which together comprise the unique key or a Route Group) does not
exist, then the server MUST create the Route Group. If a Route Group
with the given name and registrant ID does exist, then the server
MUST replace the current properties of the Route Group with the
properties passed into the AddRteGrpRqstType operation. The XSD
declarations of the AddRteGrpRqstType operation request object are as
follows:
<complexType name="AddRteGrpRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrp" type="spppb:RteGrpType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an instance of AddRteGrpRqstType, which extends
BasicRqstType and contains one RteGrpType object. The RteGrpType
object structure is defined as follows:
Mule, et al. Expires April 25, 2011 [Page 27]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="RteGrpType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rteGrpName" type="spppb:ObjNameType"/>
<element name="rteRecRef" type="spppb:RteRecRefType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="dgName" type="spppb:ObjNameType" minOccurs="0"
maxOccurs="unbounded"/>
<element name="peeringOrg" type="spppb:OrgIdType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="sourceIdent" type="spppb:SourceIdentType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="isInSvc" type="boolean"/>
<element name="priority" type="unsignedShort"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RteRecRefType">
<sequence>
<element name="rteRec" type="spppb:ObjKeyType"/>
<element name="priority" type="unsignedShort"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
The RteGrpType object is composed of the following elements:
o base: All first class objects extend BasicObjType which contains
the ID of the registrant organization that owns this object, the
ID of the registrar organization that provisioned this object,
the date and time that the object was created by the server, and
the date and time that the object was last modified. If the
client passes in either the created date or the modification
date, the server will ignore them. The server sets these two
date/time values.
o rteGrpName: The character string that contains the name of the
Route Group. It uniquely identifies this object within the
context of the registrant ID (a child element of the base
element as described above).
o rteRecRef: Set of zero or more objects of type RteRecRefType
that house the unique keys of the Route Records that the the
Mule, et al. Expires April 25, 2011 [Page 28]
Internet-Draft draft-drinks-spprov October 2010
RteGrpType object refers to and their relative priority within
the context of a given route group. The associated Route
Records contain the routing information, sometimes called SED,
associated with this Roue Group.
o dgName: Set of zero or more names of DestGrpType object
instances. Each dgName name, in association with this Route
Group's registrant ID, uniquely identifies a DestGrpType object
instance whose public identifiers are reachable using the
routing information housed in this Route Group. An intended
side affect of this is that a Route Group cannot provide routing
information for a Destination Group belonging to another
registrant.
o peeringOrg: Set of zero or more peering organization IDs that
have accepted an offer to receive this Route Group's
information. The set of peering organizations in this list is
not directly settable or modifiable using the addRteGrpsRqst
operation. This set is instead controlled using the route offer
and accept operations.
o sourceIdent: Set of zero or more SourceIdentType object
instances. These objects, described further below, house the
source identification schemes and identifiers that are applied
at resolution time as part of source based routing algorithms
for the Route Group.
o isInSvc: A boolean element that defines whether this Route Group
is in service. The routing information contained in a Route
Group that is in service is a candidate for inclusion in
resolution responses for public identities residing in the
Destination Group associated with this Route Group. The routing
information contained in a Route Group that is not in service is
not a candidate for inclusion in resolution responses.
o priority: Zero or one priority value that can be used to provide
a relative value weighting of one Route Group over another. The
manner in which this value is used, perhaps in conjunction with
other factors, is a matter of policy.
o ext: Point of extensibility described in a previous section of
this document.
As described above, the Route Group contains a set of references to
route record objects. A route record object is based on an abstract
type: RteRecType. The concrete types that use RteRecType as an
extension base are NAPTRType, NSType, and URIType. The definitions
of these types are included the Route Record section of this
Mule, et al. Expires April 25, 2011 [Page 29]
Internet-Draft draft-drinks-spprov October 2010
document.
The RteGrpType object provides support for source-based routing via
the peeringOrg data element and more granular source base routing via
the source identity element. The source identity element provides
the ability to specify zero or more of the following in association
with a given Route Group: a regular expression that is matched
against the resolution client IP address, a regular expression that
is matched against the root domain name(s), and/or a regular
expression that is matched against the calling party URI(s). The
result will be that, after identifying the visible Route Groups whose
associated Destination Group(s) contain the lookup key being queried
and whose peeringOrg list contains the querying organizations
organization ID, the resolution server will evaluate the
characteristics of the Source URI, and Source IP address, and root
domain of the lookup key being queried. The resolution server then
compares these criteria against the source identity criteria
associated with the Route Groups. The routing information contained
in Route Groups that have source based routing criteria will only be
included in the resolution response if one or more of the criteria
matches the source criteria from the resolution request. The Source
Identity data element is of type SourceIdentType, whose structure is
defined as follows:
<complexType name="SourceIdentType">
<sequence>
<element name="sourceIdentLabel" type="string"/>
<element name="sourceIdentScheme"
type="spppb:SourceIdentSchemeType"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<simpleType name="SourceIdentSchemeType">
<restriction base="token">
<enumeration value="uri"/>
<enumeration value="ip"/>
<enumeration value="rootDomain"/>
</restriction>
</simpleType>
The SourceIdentType object is composed of the following data
elements:
Mule, et al. Expires April 25, 2011 [Page 30]
Internet-Draft draft-drinks-spprov October 2010
o sourceIdentScheme: The source identification scheme that this
source identification criteria applies to and that the
associated sourceIdentRegex should be matched against.
o sourceIdentRegex: The regular expression that should be used to
test for a match against the portion of the resolution request
that is dictated by the associated sourceIdentScheme.
o ext: Point of extensibility described in a previous section of
this document.
As with the responses to all update operations, the result of the
AddRteGrpRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.2. Get Route Groups Operation
The getRteGrpsRqst operation allows a client to get the properties of
Route Group objects that a registrar organization is authorized to
view. The server will attempt to find a Route Group object that has
the registrant ID and route group name pair contained in each
ObjKeyType object instance. If the set of ObjKeyType objects is
empty then the server will return the list of Route Group objects
that the querying client has the authority to view. If there are no
matching Route Groups found then an empty result set will be
returned.
The element passed into the spppQueryRequest element for this
operation is an instance of type GetRteGrpsRqstType, which extends
BasicRqstType and contains zero or more ObjKeyType objects. Any
limitation on the maximum number of objects that may be passed into
or returned by this operation is a policy decision and not limited by
the protocol. The XSD declaration of the operation is as follows:
<complexType name="GetRteGrpsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
Mule, et al. Expires April 25, 2011 [Page 31]
Internet-Draft draft-drinks-spprov October 2010
As described in an earlier section of this document, the result of
any spppQueryRequest operation is an spppQueryResponse element that
contains the overall response code and the query result set, if any.
Refer to that section of the document for a detailed description of
the spppQueryResponse element.
6.3. Add Destination Group Operation
As described in the introductory sections, a Destination Group
represents a set of Public Identifiers with common routing
information.
The AddDestGrpRqstType operation creates or overwrites a Destination
Group object. If a Destination Group with the given name and
registrant ID (which together comprise the unique key for a
Destination Group) does not exist, then the server MUST create the
Destination Group. If a Destination Group with the given name and
registrant ID does exist, then the server MUST replace the current
properties of the Destination Group with the properties passed into
the AddDestGrpsRqstType operation. The XSD declarations of the
operation request object are as follows:
<complexType name="AddDestGrpRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="destGrp" type="spppb:DestGrpType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an element of type AddDestGrpRqsttype, which extends
BasicRqstType and contains a DestGrpType object. The DestGrpType
object structure is defined as follows:
Mule, et al. Expires April 25, 2011 [Page 32]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="DestGrpType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="dgName" type="spppb:ObjNameType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The DestGrpType object is composed of the following elements:
o base: All first class objects extend BasicObjType which contains
the ID of the registrant organization that owns this object, the
ID of the registrar organization that provisioned this object,
the date and time that the object was created by the server, and
the date and time that the object was last modified. If the
client passed in either the created date or the modification
date, the server will ignore them. The server sets these two
date/time values.
o dgName: The character string that contains the name of the
Destination Group. This uniquely identifies this object within
the context of the registrant ID (a child element of the base
element as described above).
o ext: Point of extensibility described in a previous section of
this document.
As with the responses to all update operations, the result of the
AddDestGrpRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.4. Get Destination Groups Operation
The getDestGrpsRqst operation allows a client to get the properties
of Destination Group objects that a registrar organization is
authorized to view. The server will attempt to find a Destination
Group object that has the registrant ID and destination group name
pair contained in each ObjKeyType object instance. If there are no
matching Destination Groups found then an empty result set will be
returned. If the set of ObjKeyType objects passed in is empty then
the server will return the list of Destination Group objects that the
querying registrar has the authority to view.
Mule, et al. Expires April 25, 2011 [Page 33]
Internet-Draft draft-drinks-spprov October 2010
The element passed into the spppQueryRequest element for this
operation is an instance of type GetDestGrpsRqstType, which extends
BasicQueryRqstType and contains zero or more ObjKeyType objects. Any
limitation on the maximum number of objects that may be passed into
or returned by this operation is a policy decision and not limited by
the protocol. The XSD declaration of the operation is as follows:
<complexType name="GetDestGrpsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
As described in an earlier section of this document, the result of
any spppQueryRequest operation is an spppQueryResponse element that
contains the overall response code and the query result set, if any.
Refer to that section of the document for a detailed description of
the spppQueryResponse element.
6.5. Add Route Group Offer Operation
The list of peer organizations whose resolution responses can include
the routing information contained in a given Route Group is
controlled by the organization to which a Route Group object belongs
(its registrant), and the peer organization that submits resolution
requests (a data recipient, also know as a peering organization).
The registrant offers access to a Route Group by submitting a Route
Group Offer. The data recipient can then accept or reject that
offer. Not until access to a Route Group has been offered and
accepted will the data recipient's organization ID be included in the
peeringOrg list in a Route Group object, and that Route Group's
peering information become a candidate for inclusion in the responses
to the resolution requests submitted by that data recipient. The
AddRteGrpOffersRqstType operation creates or overwrites one or more
Route Group Offer objects. If a Route Group Offer for the given
Route Group object key and the offeredToOrg ID does not exist, then
the server creates the Route Group Offer object. If a such a Route
Group Offer does exist, then the server replaces the current object
with the new object. The XSD declarations of the operation request
object are as follows:
Mule, et al. Expires April 25, 2011 [Page 34]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="AddRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOffer" type="spppb:RteGrpOfferType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an instance of AddRteGrpOfferRqstType, which extends
BasicRqstType and contains a RteGrpOfferType object. The XSD
declaration of the RteGrpOfferType is as follows:
<complexType name="RteGrpOfferType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType"/>
<element name="status" type="spppb:RteGrpOfferStatusType"/>
<element name="offerDateTime" type="dateTime"/>
<element name="acceptDateTime" type="dateTime" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RteGrpOfferKeyType">
<sequence>
<element name="rteGrpKey" type="spppb:ObjKeyType"/>
<element name="offeredTo" type="spppb:OrgIdType"/>
</sequence>
</complexType>
<simpleType name="RteGrpOfferStatusType">
<restriction base="token">
<enumeration value="offered"/>
<enumeration value="accepted"/>
</restriction>
</simpleType>
Mule, et al. Expires April 25, 2011 [Page 35]
Internet-Draft draft-drinks-spprov October 2010
The RteGrpOfferType object is composed of the following elements:
o base: All first class objects extend BasicObjType which contains
the ID of the registrant organization that owns this object, the
ID of the registrar organization that provisioned this object,
the date and time that the object was created by the server, and
the date and time that the object was last modified. If the
client passed in either the created date or the modification
date, the will ignore them. The server sets these two date/time
values.
o rteGrpOfferKey: The object that identifies the route that is or
has been offered and the organization that it is or has been
offered to. The combination of these three data elements
uniquely identify a Route Group Offer.
o status: The status of the offer, offered or accepted. This
status is controlled by the server. It is automatically set to
"offered" when ever a new Route Group Offer is added, and is
automatically set to "accepted" if and when that offer is
accepted. The value of the element is ignored when passed in by
the client.
o offerDateTime: Date and time in GMT when the Route Group Offer
was added.
o acceptDateTime: Date and time in GMT when the Route Group Offer
was accepted.
As with the responses to all update operations, the result of the
AddRteGrpOfferRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.6. Accept Route Group Offer Operation
Not until access to a Route Group has been offered and accepted will
the data recipient's organization ID will it be included in the
peeringOrg list in that Route Group object, and that Route Group's
peering information become a candidate for inclusion in the responses
to the resolution requests submitted by that data recipient. The
AcceptRteGrpOffersRqstType operation is called by, or on behalf of,
the data recipient to accept a Route Group Offer that is pending in
the "offered" status for the data recipient's organization ID. If a
Route Group Offer for the given Route Group Offer key (route name,
route registrant ID, data recipient's organization ID) exists, then
the server moves the Route Group Offer to the "accepted" status and
Mule, et al. Expires April 25, 2011 [Page 36]
Internet-Draft draft-drinks-spprov October 2010
adds that data recipient's organization ID into the list of
peerOrgIds for that Route Group. If a such a Route Group Offer does
not exist, then the server returns the appropriate error code, 2105.
The XSD declarations for the operation request object are as follows:
<complexType name="AcceptRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOfferKey" type="spppb:RteGrpOfferKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an instance of AcceptRteGrpOffersRqstType, which extends
BasicRqstType and contains a RteGrpOfferKeyType object.
As with the responses to all update operations, the result of the
AcceptRteGrpOfferRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.7. Reject Route Group Offer Operation
The data recipient to which a Route Group has been offered has the
option of rejecting a Route Group Offer. Furthermore, that offer may
be rejected, regardless of whether or not it has been previously
accepted. The RejectRteGrpOffersRqstType operation is used for these
purposes and is called by, or on behalf of, the data recipient to
accept a Route Group Offer that is pending in the "offered" status or
is in the "accepted" status for the data recipient's organization ID.
If a Route Group Offer for the given Route Group Offer key (route
name, route registrant ID, data recipient's organization ID) exists
in either the offered or accepted status, then the server deletes
that Route Group Offer object, and, if appropriate, removes the data
recipients organization ID from the list of peeringOrg IDs for that
Route Group. If the Route Group Offer does not exist, then the
server returns the appropriate error code, 2105. The XSD
declarations for the operation request object are as follows:
Mule, et al. Expires April 25, 2011 [Page 37]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="RejectRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOfferKey" type="spppb:RteGrpOfferKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an instance of RejectRteGrpOffersRqstType, which extends
BasicRqstType and contains a RteGrpOfferKeyType object.
As with the responses to all update operations, the result of the
RejectRteGrpOfferRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.8. Get Route Group Offers Operation
The getRteGrpOffersRqst operation allows a client to get the
properties of zero or more Route Group Offer objects that registrar
is authorized to view. The server will attempt to find Route Group
Offer objects that have all the properties specified in the criteria
passed into the operation. If no criteria is passed in then the
server will return the list of Route Group Offer objects that the
querying client has the authority to view. If there are no matching
Route Group Offers found then an empty result set will be returned.
The element passed into the spppQueryRequest element for this
operation is an instance of GetRteGrpOffersRqstType, which extends
BasicQueryRqstType and contains the criteria that the returned Route
Group Offer objects must match. Any limitation on the maximum number
of objects that may be returned by this operation is a policy
decision and not limited by the protocol. The XSD declaration of the
operation is as follows:
Mule, et al. Expires April 25, 2011 [Page 38]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="GetRteGrpOffersRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="offeredByPeers" type="boolean" minOccurs="0"/>
<element name="offeredToPeers" type="boolean" minOccurs="0"/>
<element name="status" type="spppb:RteGrpOfferStatusType"
minOccurs="0"/>
<element name="peeringOrg" type="spppb:OrgIdType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
The GetRteGrpOffersRqstType object is composed of the following
elements:
o offeredByPeers: Zero or one boolean value that, if true,
indicates that only offers that are offered by peering
organizations to the querying registrant should be included in
the result set. If this value is false, the offers by peering
organizations to the querying registrant should not be included
in the result set. The result set is also subject to other
query criteria in the request.
o offeredToPeers: Zero or one boolean value that, if true,
indicates that only offers that are offered to peering
organizations by the querying registrant should be included in
the result set. If this value is false, the offers to peering
organizations by the querying registrant should not be included
in the result set. The result set is also subject to other
query criteria in the request.
o status: The status of the offer, offered or accepted. Only
offers in the specified status should be included in the result
set. If this element is not present then the status of the
offer should not be considered in the query. The result set is
also subject to other query criteria in the request.
o peeringOrg: Zero or more organization IDs. Only offers that are
offered to or offered by the organization IDs in this list
should be included in the result set. The result set is also
subject to other query criteria in the request.
Mule, et al. Expires April 25, 2011 [Page 39]
Internet-Draft draft-drinks-spprov October 2010
o rteGrpOfferKey: Zero or more Route Group Offer Keys. Only
offers having one of these keys should be included in the result
set. The result set is also subject to other query criteria in
the request.
As described in an earlier section of this document, the result of
any spppQueryRequest operation is an spppQueryResponse element that
contains the overall response code and the query result set, if any.
Refer to that section of the document for a detailed description of
the spppQueryResponse element.
6.9. Public Identifier Operations
Public Identifier is the search key used for locating the session
establishment data (SED). In many cases, a Public Identifier is
attributed to the end user who has a retail relationship with the
service provider or registrant organization. In SPPP, SED can be
provisioned by the registrant, or by the registrar on behalf of the
registrant. Also, SPPP supports the notion of the carrier-of-record
as defined in RFC 5067. Therefore, the entity adding the Public
Identity in the Registry can optionally claim to be a carrier-of-
record.
SPPP identifies three types of Public Identifiers: telephone number
(TN), email address, and the routing number (RN). SPPP provides
structures to manage a single TN, a contiguous range of TNs, and a TN
prefix.
The XML schema type definition PubIDType is the generalization of the
Public Identifier. PubIDType is an abstract type. In agreement with
the data model, PubIDType member 'dgName' represents the name of the
destination group that a given Public Identifier is associated to.
The PubIDType object structure is defined as follows:
<complexType name="PubIdType" abstract="true">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="dgName" type="spppb:ObjNameType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
A registrant can add a Public Identifier with the help of a
Mule, et al. Expires April 25, 2011 [Page 40]
Internet-Draft draft-drinks-spprov October 2010
BasicRqstType called AddPubIdRqstType. To complete the add request,
AddPubIdRqstType XML instance is added to <spppUpdateRequest> root
element. If there is a conflict and a Public Identifier already
exists in the Registry, the old entry will be replaced with the newly
provisioned entry. For the add or update operation, the destination
group name is a mandatory parameter. Not including a valid
destination group name in the update request will cause the Registry
to return an appropriate error.
Telephone number is identified by TNType, an extension of PubIDType.
TNType is composed of the following attributes:
o tn: Telephone number to be added to the Registry.
o rteRecRef: Optional reference to the route record that is
directly associated with the TN Public Identifier. Following
the SPPP data model, the route record could be a protocol
agnostic URIType or another type.
o corInfo: corInfo is an optional parameter of type CORInfoType
that allows the registrant organization to set forth a claim to
be the carrier-of-record [see RFC 5067]. This is done by
setting the value of <corClaim> element of the CORInfoType
object structure to "true". The other two parameters of the
CORInfoType, <cor> and <corDateTime> are set by the Registry to
describe the outcome of the carrier-of-record claim by the
registrant. In general, inclusion of <corInfo> parameter is
useful if the Registry has the authority information, such as,
the number portability data, etc., in order to qualify whether
the registrant claim can be satisfied. If the carrier-of-record
claim disagrees with the authority data in the Registry, whether
the TN add operation fails or not is a matter of policy and it
is beyond the scope of this document. In the response message
<spppUpdateResponse>, the SPPP Server must include the <cor>
parameter of the <corInfo> element to let the registrant know
the outcome of the claim.
TNType object definition is as follows:
Mule, et al. Expires April 25, 2011 [Page 41]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="TNType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="tn" type="string"/>
<element name="rteRecRef" type="spppb:RteRecRefType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
Routing number is identified by RNType. SSPs that possess the number
portability data may be able to leverage the RN search key to
discover the ingress routes for session establishment. Therefore,
the registrant organization can add the RN and associate it with the
appropriate destination group to share the route information.
RNType is composed of the following attributes:
o rn: Routing Number used as the search key
o corInfo: Optional <corInfo> element of type CORInfoType.
RNType object information is as follows:
<complexType name="RNType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="rn" type="string" default="true"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
A contiguous range of TNs is added with the help of TNRType
structure. The object definition requires a starting TN and the
ending TN that describes the TN range. In addition, TNRType includes
an optional "prefix" attribute to indicate that the given TN range
Mule, et al. Expires April 25, 2011 [Page 42]
Internet-Draft draft-drinks-spprov October 2010
qualifies for the Open Number Plan (ONP). In order to correctly
expand the number range that qualifies for Open Number Plan, the
Registry must have the required data related to the national
significant number length for the TNs in the TN range object.
Further, <spppUpdateRequest> is transactional in nature, therefore,
if the Registry encounters an error in adding even a single TN of a
TNRType object, the whole request will be deemed a failure. In other
words, the partial success case is not supported.
TNRType is composed of the following attributes:
o startTn: Starting TN in the TN range
o endTn: The last TN in the TN range
o corInfo: Optional <corInfo> element of type CORInfoType
o prefix: Optional attribute, when set to "true", indicates that
the Open Number Plan applies to a given TN Range
TNPType object structure is as follows:
<complexType name="TNRType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="startTn" type="string"/>
<element name="endTn" type="string"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
<attribute name="prefix" type="boolean" default="false">
</attribute>
</extension>
</complexContent>
</complexType>
In some cases, it is useful to describe a set of TNs with the help of
the first few digits of the telephone numbers identified as telephone
number prefix. In many instances, the numbering authority assigns TN
prefix, also referred to as a TN block, to a well-known telephony
service provider. In SPPP, the TNPType structure describes a TN
prefix and it consists of the following attributes:
Mule, et al. Expires April 25, 2011 [Page 43]
Internet-Draft draft-drinks-spprov October 2010
o tnPrefix: The telephone number prefix
o corInfo: Optional <corInfo> element of type CORInfoType.
TNPType object structure is as follows:
<complexType name="TNPType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="tnPrefix" type="string"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
The object structure of AddPubIdRqstType used to add Public
Identifiers is as follows
<complexType name="AddPubIdRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="pi" type="spppb:PubIdType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The client can set the GetPubIdsRqstType in the <spppQueryRequest>
structure to obtain information about one or more <pi> objects that
were successfully provisioned earlier and that the calling entity is
privileged to see. If the GetPubIdsRqstType object does not include
<pi> data, then all authorized Public Identity data will be returned
by the Registry in the response. If no matching Public Identifiers
are found, then an empty result set will be returned.
GetPubIdsRqstType object structure is as follows:
Mule, et al. Expires April 25, 2011 [Page 44]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="GetPubIdsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="pi" type="spppb:PubIdType" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
As described in an earlier section of this document, the result of
any spppQueryRequest operation is a spppQueryResponse that contains
the response code and the query result set, if any.
6.10. Egress Route Operations
The egress route add operation allows a call originating SSP to
define a preferred egress route in an attempt to reach the ingress
SBE of the target SSP. The need arises when there is a choice of
egress SBE and an SSP wants to exercise greater control in deciding
how to route the outbound session establishment request.
As a first step, it is assumed that the target SSP has offered to
share the route group that consists of the ingress route information
to the SBE(s) and the originating SSP has accepted the offer. Next,
the originating SSP can add the egress route in the Registry, with
appropriate regular expression, to rewrite ingress route information
from the target SSP and include the egress SBE information. In high-
availability configurations, the originating SSP will likely add a
secondary egress route object re-writing the same ingress route from
the target SSP with a secondary choice of egress SBE as a backup. In
this case, the backup egress route definition will carry the higher
integer value for the "pref" parameter to indicate a lower priority.
An egress route is identified by type EgrRteType and its object
structure is shown below:
Mule, et al. Expires April 25, 2011 [Page 45]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="EgrRteType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="egrRteName" type="spppb:ObjNameType"/>
<element name="pref" type="unsignedShort"/>
<element name="regxRewriteRule" type="spppb:RegexParamType"/>
<element name="ingrRteRec" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
The EgrRteType object is composed of the following elements:
o base: All first class objects extend BasicObjType which contains
the ID of the registrant organization that owns this object, the
ID of the registrar organization that provisioned this object,
the date and time that the object was created by the server, and
the date and time that the object was last modified. If the
client passes in either the created date or the modification
date, the server will ignore them. The server sets these two
date/time values.
o egrRteName: The name of the egress route.
o pref: The preference of this egress route relative to other
egress routes that may get selected when responding to a
resolution request.
o regxRewriteRule: The regular expression re-write rule that
should be applied to the regular expression of the ingress
NAPTR(s) that belong to the ingress route.
o ingrRteRec: The ingress route records that the egress route
should be used for.
o ext: Point of extensibility described in a previous section of
this document.
The AddEgrRteRqstType request is used to create or overwrite an
egress route.
Mule, et al. Expires April 25, 2011 [Page 46]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="AddEgrRteRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="egrRte" type="spppb:EgrRteType"/>
</sequence>
</extension>
</complexContent>
</complexType>
An instance of AddEgrRtesRqstType is added in the spppUpdateRequest
element in order to send a valid request to the server. Any
limitation on the maximum number of AddEgrRteRqstType instances is a
matter of policy and is not limited by the specification.
The response from the server is returned in addEgrRteRspns element,
which is defined as the element of type BasicRspnsType.
The GetEgrRtesRqstType is used by an authorized entity to fetch the
well-known egress route data.
<complexType name="GetEgrRtesRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
6.11. Add Route Record Operation
As described in the introductory sections, a Route Group represents a
combined grouping of Route Records that define route information.
However, Route Records need not be created to just server a single
Route Group. Route Records can be created and managed to serve
multiple Route Groups. As a result, a change to the properties of a
network node, for example, that is used for multiple routes, would
necessitate just a single update operation to change the properties
of that node. The change would then be reflected in all the Route
Groups whose route record set contains a reference to that node.
Mule, et al. Expires April 25, 2011 [Page 47]
Internet-Draft draft-drinks-spprov October 2010
The AddRteRecRqstType operation creates or overwrites a Route Record
object. If a Route Record with the given name and registrant ID
(which together comprise the unique key or a Route Record) does not
exist, then the server MUST create the Route Record. If a Route
Record with the given name and registrant ID does exist, then the
server MUST replace the current properties of the Route Record with
the properties passed into the AddRteRecRqstType operation. The XSD
declarations of the AddRteRecRqstType operation request object are as
follows:
<complexType name="AddRteRecRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteRec" type="spppb:RteRecType"/>
</sequence>
</extension>
</complexContent>
</complexType>
The element passed into the spppUpdateRequest element for this
operation is an instance of AddRteRecRqstType, which extends
BasicRqstType and contains one RteRecType object. The RteRecType
object structure is defined as follows:
<complexType name="RteRecType" abstract="true">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rrName" type="spppb:ObjNameType"/>
<element name="priority" type="unsignedShort" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
The RteRecType object is composed of the following elements:
o base: All first class objects extend BasicObjType which contains
the ID of the registrant organization that owns this object, the
ID of the registrar organization that provisioned this object,
the date and time that the object was created by the server, and
Mule, et al. Expires April 25, 2011 [Page 48]
Internet-Draft draft-drinks-spprov October 2010
the date and time that the object was last modified. If the
client passes in either the created date or the modification
date, the server will ignore them. The server sets these two
date/time values.
o rrName: The character string that contains the name of the Route
Record. It uniquely identifies this object within the context
of the registrant ID (a child element of the base element as
described above).
o priority: Zero or one priority value that can be used to provide
a relative value weighting of one Route Record over another.
The manner in which this value is used, perhaps in conjunction
with other factors, is a matter of policy.
o ext: Point of extensibility described in a previous section of
this document.
As described above, route records are based on an abstract type:
RteRecType. The concrete types that use RteRecType as an extension
base are NAPTRType, NSType, and URIType. The definitions of these
types are included below. The NAPTRType object is comprised of the
data elements necessary for a NAPTR that contains routing information
for a Route Group. The NSType object is comprised of the data
elements necessary for a Name Server that points to another DNS
server that contains the desired routing information. The URIType
object is comprised of the data elements necessary to house a URI.
The data provisioned in a Registry can be leveraged for many purposes
and queried using various protocols including SIP, ENUM and others.
It is for this reason that a route record type offers a choice of URI
and DNS resource record types. URIType fulfills the need for both
SIP and ENUM protocols. When a given URIType is associated to a
destination group, the user part of the replacement string <uri> that
may require the Public Identifier cannot be preset. As a SIP
Redirect, the resolution server will apply <ere> pattern on the input
Public Identifier in the query and process the replacement string by
substituting any back reference(s) in the <uri> to arrive at the
final URI that is returned in the SIP Contact header. For an ENUM
query, the resolution server will simply return the value of the
<ere> and <uri> members of the URIType in the NAPTR REGEX parameter.
<complexType name="RteRecType" abstract="true">
<sequence>
<element name="rrName" type="spppb:ObjNameType"/>
<element name="priority" type="unsignedShort"/>
Mule, et al. Expires April 25, 2011 [Page 49]
Internet-Draft draft-drinks-spprov October 2010
</sequence>
</complexType>
<complexType name="NAPTRType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="order" type="unsignedShort"/>
<element name="flags" type="string" minOccurs="0"/>
<element name="svcs" type="string"/>
<element name="regx" type="spppb:RegexParamType"
minOccurs="0"/>
<element name="repl" type="string" minOccurs="0"/>
<element name="ttl" type="positiveInteger" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="NSType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="hostName" type="string"/>
<element name="ipAddr" type="spppb:IPAddrType" minOccurs="0"
maxOccurs="unbounded"/>
<element name="ttl" type="positiveInteger" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="URIType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="ere" type="string" default="^(.*)$"/>
<element name="uri" type="string"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="IPAddrType">
<sequence>
<element name="addr" type="string"/>
Mule, et al. Expires April 25, 2011 [Page 50]
Internet-Draft draft-drinks-spprov October 2010
<element name="type" type="spppb:IPType"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<simpleType name="IPType">
<restriction base="token">
<enumeration value="IPv4"/>
<enumeration value="IPv6"/>
</restriction>
</simpleType>
The NAPTRType object is composed of the following elements:
o order: Order value in an ENUM NAPTR, relative to other NAPTRType
objects in the same Route Group.
o svcs: ENUM service(s) that are served by the SBE. This field's
value must be of the form specified in [RFC3761] (e.g., E2U+
pstn:sip+sip). The allowable values are a matter of policy and
not limited by this protocol.
o regx: NAPTR's regular expression field. If this is not included
then the Repl field must be included.
o repl: NAPTR replacement field, should only be provided if the
Regex field is not provided, otherwise it will be ignored by the
server.
o ttl: Number of seconds that an addressing server may cache this
NAPTR.
o ext: Point of extensibility described in a previous section of
this document.
The NSType object is composed of the following elements:
o hostName: Fully qualified host name of the name server.
o ipAddr: Zero or more objects of type IpAddrType. Each object
holds an IP Address and the IP Address type, IPv4 or IP v6.
o ttl: Number of seconds that an addressing server may cache this
Name Server.
Mule, et al. Expires April 25, 2011 [Page 51]
Internet-Draft draft-drinks-spprov October 2010
o ext: Point of extensibility described in a previous section of
this document.
The URIType object is composed of the following elements:
o ere: The POSIX Extended Regular Expression (ere) as defined in
[RFC3986].
o uri: the URI as defined in [RFC3986]. In some cases, this will
serve as the replacement string and it will be left to the
resolution server to arrive at the final usable URI.
As with the responses to all update operations, the result of the
AddRteRecRqstType operation is contained in the generic
spppUpdateResponse data structure described in an earlier sections of
this document. For a detailed description of the spppUpdateResponse
data structure refer to that section of the document.
6.12. Get Route Records Operation
The getRteRecsRqst operation allows a client to get the properties of
Route Record objects that a registrar organization is authorized to
view. The server will attempt to find a Route Record object that has
the registrant ID and route record name pair contained in each
ObjKeyType object instance. If the set of ObjKeyType objects is
empty then the server will return the list of Route Record objects
that the querying client has the authority to view. If there are no
matching Route Record found then an empty result set will be
returned.
The element passed into the spppQueryRequest element for this
operation is an instance of type GetRteRecsRqstType, which extends
BasicRqstType and contains zero or more ObjKeyType objects. Any
limitation on the maximum number of objects that may be passed into
or returned by this operation is a policy decision and not limited by
the protocol. The XSD declaration of the operation is as follows:
<complexType name="GetRteRecsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
Mule, et al. Expires April 25, 2011 [Page 52]
Internet-Draft draft-drinks-spprov October 2010
</complexType>
As described in an earlier section of this document, the result of
any spppQueryRequest operation is an spppQueryResponse element that
contains the overall response code and the query result set, if any.
Refer to that section of the document for a detailed description of
the spppQueryResponse element.
6.13. Delete Operation
In order to remove an object from the Registry, an authorized entity
can send the <spppUpdateRequest> to the Registry with a corresponding
delete BasicRqstType object. If the entity that issued the command
is not authorized to perform this operation or if the public
identifier doesn't exist, an appropriate error code will be returned
in the <spppUpdateRespnonse> message.
As an example, DelPubIdRqstType aids in identifying the Public
Identifier that is used to delete a Public Identifier from the
Registry. DelPubIdsRqstType object definition is shown below:
<complexType name="DelPubIdRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="pi" type="spppb:PubIdType"/>
</sequence>
</extension>
</complexContent>
</complexType>
Similarly, each 'Add' operation in the SP protocol has a
corresponding 'Del' operation used to delete the respective object
type from the Registry.
Mule, et al. Expires April 25, 2011 [Page 53]
Internet-Draft draft-drinks-spprov October 2010
7. SPPP Examples
This section shows XML message exchange between two SIP Service
Providers (SSP) and a Registry. For the sake of simplicity, the
transport wrapper for the SPPP protocol is left out. The SPPP
protocol messages in this section are valid XML instances that
conform to the SPPP schema version within this document.
In this sample use case scenario, SSP1 and SSP2 provision resource
data in the registry and use SPPP constructs to selectively share the
route groups. In the figure below, SSP2 has two ingress SBE
instances that are associated with the public identities that SSP2
has the retail relationship with. Also, the two SBE instances for
SSP1 are used to show how to use SPPP protocol to associate route
preferences for the destination ingress routes and exercise greater
control on outbound traffic to the peer's ingress SBEs.
---------------+ +------------------
| |
+------+ +------+
| sbe1 | | sbe2 |
+------+ +------+
SSP1 | | SSP2
+------+ +------+
| sbe3 | | sbe4 |
+------+ +------+
iana-en:111 | | iana-en:222
---------------+ +------------------
| |
| |
| SPPP +------------------+ SPPP |
+------->| Registry |<--------+
+------------------+
7.1. Add Destination Group
SSP2 adds a destination group to the Registry for use later. The
SSP2 SPPP client sets a unique transaction identifier 'tx_7777' for
tracking purposes. The name of the destination group is set to
DEST_GRP_SSP2_1
Mule, et al. Expires April 25, 2011 [Page 54]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<clientTransId>txid-5555</clientTransId>
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddDestGrpRqstType">
<destGrp>
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:rarId>iana-en:222</ns1:rarId>
<dgName>DEST_GRP_SSP2_1</dgName>
</destGrp>
</rqst>
</spppUpdateRequest>
The Registry processes the request and return a favorable response
confirming successful creation of the named destination group. Also,
besides returning a unique transaction identifier, Registry also
returns the matching client transaction identifier from the request
message back to the SPPP client.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<clientTransId>tx_7777</clientTransId>
<serverTransId>tx_id_12346</serverTransId>
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
</spppUpdateResponse>
7.2. Add Route Records
SSP2 adds an ingress routes in the Registry.
Mule, et al. Expires April 25, 2011 [Page 55]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddRteRecRqstType">
<rteRec xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:NAPTRType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:rrName>RTE_SSP2_SBE2</ns1:rrName>
<order>10</order>
<flags>u</flags>
<svcs>E2U+sip</svcs>
<regx>
<ere>^(.*)$</ere>
<repl>sip:\1@sbe2.ssp2.example.com</repl>
</regx>
</rteRec>
</rqst>
</spppUpdateRequest>
The Registry returns a success response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_11145</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.3. Add Route Records -- URIType
SSP2 adds another ingress routes in the Registry and makes use of
URIType
Mule, et al. Expires April 25, 2011 [Page 56]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddRteRecRqstType">
<rteRec xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:URIType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:rrName>RTE_SSP2_SBE4</ns1:rrName>
<ns1:ere>^(.*)$</ns1:ere>
<ns1:uri>sip:\1;npdi@sbe4.ssp2.example.com</ns1:uri>
</rteRec>
</rqst>
</spppUpdateRequest>
The Registry returns a success response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_11145</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.4. Add Route Group
SSP2 creates the grouping of the ingress routes and choses higher
precedence for RTE_SSP2_SBE2 by setting a lower number for the
"priority" attribute, a protocol agnostic precedence indicator.
Mule, et al. Expires April 25, 2011 [Page 57]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddRteGrpRqstType">
<rteGrp>
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<rteGrpName>RTE_GRP_SSP2_1</rteGrpName>
<ns1:rteRecRef>
<ns1:rteRec>
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:name>RTE_SSP2_SBE2</ns1:name>
</ns1:rteRec>
<ns1:priority>100</ns1:priority>
</ns1:rteRecRef>
<dgName>DEST_GRP_SSP2_1</dgName>
<isInSvc>true</isInSvc>
<ns1:priority>10</ns1:priority>
</rteGrp>
</rqst>
</spppUpdateRequest>
To confirm successful processing of this request, Registry returns a
well-known resolution code '1000' to the SSP2 client.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12345</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
Mule, et al. Expires April 25, 2011 [Page 58]
Internet-Draft draft-drinks-spprov October 2010
7.5. Add Public Identity -- Successful COR claim
SSP2 activates a TN public identity by associating it with a valid
destination group. Further, SSP2 puts forth a claim that it is the
carrier-of-record for the TN.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<clientTransId>txid-5577</clientTransId>
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNType">
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:rarId>iana-en:222</ns1:rarId>
<ns1:crtDate>2010-05-30T09:30:10Z</ns1:crtDate>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<tn>+12025556666</tn>
<ns1:corInfo>
<ns1:corClaim>true</ns1:corClaim>
</ns1:corInfo>
</pi>
</rqst>
</spppUpdateRequest>
Assuming that the Registry has access to TN authority data and it
performs the required checks to verify that SSP2 is in fact the
service provider of record for the given TN, the request was
processed successfully. <cor> element confirms SSP2 claim to be the
carrier of record has been accepted and the processing time is
reflected by <corDateTime> data element.
Mule, et al. Expires April 25, 2011 [Page 59]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<clientTransId>txid-5577</clientTransId>
<serverTransId>tx_id_12345</serverTransId>
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<rqstObjResult>
<code>1000</code>
<msg>success</msg>
<rqstObj xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNType">
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:rarId>iana-en:222</ns1:rarId>
<ns1:crtDate>2010-05-30T09:30:10Z</ns1:crtDate>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<tn>+12025556666</tn>
<ns1:corInfo>
<ns1:corClaim>true</ns1:corClaim>
<ns1:cor>true</ns1:cor>
<ns1:corDateTime>2006-05-04T18:13:51.0Z
</ns1:corDateTime>
</ns1:corInfo>
</pi>
</rqstObj>
</rqstObjResult>
</spppUpdateResponse>
7.6. Add LRN
If another entity that SSP2 shares the routes with has access to
Number Portability data, it may choose to perform route lookups by
routing number. Therefore, SSP2 associates a routing number to a
destination group in order to facilitate ingress route discovery.
Mule, et al. Expires April 25, 2011 [Page 60]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:RNType">
<rantId>rantId0</rantId>
<rarId>rarId0</rarId>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<rn>2025550000</rn>
</pi>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response to the SPPP client.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12345</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.7. Add TN Range
Next, SSP2 activates a block of ten thousand TNs and associate it to
a destination group. Since the 'prefix' public identity attribute is
not set to 'true', this means that the TNs belong to a closed number
plan.
Mule, et al. Expires April 25, 2011 [Page 61]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNRType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<startTn>+12026660000</startTn>
<endTn>+12026669999</endTn>
</pi>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12244498</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.8. Add TN Range with Open Number Plan support
In this case, open number plan refers to TN length variance.
Inclusion of "prefix" attribute of TNRType with its value set to true
indicates that the start TN range identified by the <tn> element is
not necessarily a subscriber number and the Registry will have to
consult the number plan data for the respective country to know how
to expand the number range. <endTn> attribute marks the end of the TN
range.
Mule, et al. Expires April 25, 2011 [Page 62]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNRType" prefix="true">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<startTn>+4312315566</startTn>
<endTn>+4312315567</endTn>
</pi>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12255598</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.9. Add TN Prefix
Next, SSP2 activates a block of ten thousand TNs using the TNPType
structure and identifying a TN prefix.
Mule, et al. Expires April 25, 2011 [Page 63]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNPType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:dgName>DEST_GRP_SSP2_1</ns1:dgName>
<tnPrefix>+1202777</tnPrefix>
</pi>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12387698</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
7.10. Enable Peering -- Route Group Offer
In order for SSP1 to complete session establishment for a destination
TN where the target subscriber has a retail relationship with SSP2,
it first requires an asynchronous bi-directional handshake to show
mutual consent. To start the process, SSP2 initiates the peering
handshake by offering SSP1 access to its route group.
Mule, et al. Expires April 25, 2011 [Page 64]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddRteGrpOfferRqstType">
<rteGrpOffer>
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<rteGrpOfferKey>
<rteGrpKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</rteGrpKey>
<offeredTo>iana-en:111</offeredTo>
</rteGrpOfferKey>
<status>offered</status>
<offerDateTime>2006-05-04T18:13:51.0Z</offerDateTime>
</rteGrpOffer>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and confirms that the
SSP1 will now have the opportunity to weigh in on the offer and
either accept or reject it. The Registry may employ out-of-band
notification mechanisms for quicker updates to SSP1 so they can act
faster, though this topic is beyond the scope of this document.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12277798</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
</spppUpdateResponse>
Mule, et al. Expires April 25, 2011 [Page 65]
Internet-Draft draft-drinks-spprov October 2010
7.11. Enable Peering -- Route Group Offer Accept
SSP1 responds to the offer from SSP2 and agrees to have visibility to
SSP2 ingress routes.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AcceptRteGrpOfferRqstType">
<rteGrpOfferKey>
<rteGrpKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</rteGrpKey>
<offeredTo>iana-en:111</offeredTo>
</rteGrpOfferKey>
</rqst>
</spppUpdateRequest>
Registry confirms that the request has been processed successfully.
From this point forward, if SSP1 looks up a public identity through
the query resolution server, where the public identity is part of the
destination group by way of "RTE_GRP_SSP2_1" route association, SSP2
ingress SBE information will be shared with SSP1.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<serverTransId>tx_id_12333798</serverTransId>
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
</spppUpdateResponse>
Mule, et al. Expires April 25, 2011 [Page 66]
Internet-Draft draft-drinks-spprov October 2010
7.12. Add Egress Route
SSP1 wants to prioritize all outbound traffic to routes associated
with "RTE_GRP_SSP2_1" route group through "sbe1.ssp1.example.com".
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<clientTransId>tx_9000</clientTransId>
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:AddEgrRteRqstType">
<egrRte>
<rantId>iana-en:111</rantId>
<rarId/>
<egrRteName>EGR_RTE_01</egrRteName>
<pref>50</pref>
<regxRewriteRule>
<ere>^(.*@)(.*)$</ere>
<repl>\1\2?route=sbe1.ssp1.example.com</repl>
</regxRewriteRule>
<ns1:ingrRteRec>
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:name>SSP2_RTE_REC_3</ns1:name>
</ns1:ingrRteRec>
</egrRte>
</rqst>
</spppUpdateRequest>
Since peering has already been established, the request to add the
egress route has been successfully completed.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd"
xmlns="urn:ietf:params:xml:ns:sppp:base:1">
<clientTransId>tx_9000</clientTransId>
<serverTransId>tx_id_12388898</serverTransId>
<overallResult>
<code>1000</code>
<msg>Request successful</msg>
</overallResult>
Mule, et al. Expires April 25, 2011 [Page 67]
Internet-Draft draft-drinks-spprov October 2010
</spppUpdateResponse>
7.13. Get Destination Group
SSP2 uses the 'GetDestGrpsRqstType' operation to tally the last
provisioned record for destination group DEST_GRP_SSP2_1.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:GetDestGrpsRqstType">
<objKey>
<rantId>iana-en:222</rantId>
<name>DEST_GRP_SSP2_1</name>
</objKey>
</rqst>
</spppQueryRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<resultSet xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DestGrpType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<dgName>DEST_GRP_SSP2_1</dgName>
</resultSet>
</spppQueryResponse>
Mule, et al. Expires April 25, 2011 [Page 68]
Internet-Draft draft-drinks-spprov October 2010
7.14. Get Public Identity
SSP2 obtains the last provisioned record associated with a given TN.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:GetPubIdsRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<tn>+12025556666</tn>
</pi>
</rqst>
</spppQueryRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<resultSet xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<ns1:dgName>DEST_GRP_1</ns1:dgName>
<tn>+12025556666</tn>
<ns1:corInfo>
<ns1:corClaim>true</ns1:corClaim>
<ns1:cor>true</ns1:cor>
<ns1:corDateTime>2010-05-30T09:30:10Z</ns1:corDateTime>
</ns1:corInfo>
</resultSet>
</spppQueryResponse>
Mule, et al. Expires April 25, 2011 [Page 69]
Internet-Draft draft-drinks-spprov October 2010
7.15. Get Route Group Request
SSP2 obtains the last provisioned record for the route group
RTE_GRP_SSP2_1.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:GetRteGrpsRqstType">
<objKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</objKey>
</rqst>
</spppQueryRequest>
Registry completes the request successfully and returns a favorable
response.
Mule, et al. Expires April 25, 2011 [Page 70]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<resultSet xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:RteGrpType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<rteGrpName>RTE_GRP_SSP2_1</rteGrpName>
<ns1:rteRecRef>
<ns1:rteRec>
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:name>RTE_SSP2_SBE2</ns1:name>
</ns1:rteRec>
<ns1:priority>100</ns1:priority>
</ns1:rteRecRef>
<ns1:rteRecRef>
<ns1:rteRec>
<ns1:rantId>iana-en:222</ns1:rantId>
<ns1:name>RTE_SSP2_SBE4</ns1:name>
</ns1:rteRec>
<ns1:priority>101</ns1:priority>
</ns1:rteRecRef>
<dgName>DEST_GRP_SSP2_1</dgName>
<isInSvc>true</isInSvc>
<ns1:priority>10</ns1:priority>
</resultSet>
</spppQueryResponse>
7.16. Get Route Group Offers Request
SSP2 choses to fetch the last provisioned route group sharing offer
to the <peeringOrg> SSP1.
Mule, et al. Expires April 25, 2011 [Page 71]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:GetRteGrpOffersRqstType">
<ns1:offeredToPeers>true</ns1:offeredToPeers>
<ns1:peeringOrg>ssp1</ns1:peeringOrg>
</rqst>
</spppQueryRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<resultSet xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:RteGrpOfferType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<rteGrpOfferKey>
<rteGrpKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</rteGrpKey>
<offeredTo>iana-en:111</offeredTo>
</rteGrpOfferKey>
<status>offered</status>
<offerDateTime>2006-05-04T18:13:51.0Z</offerDateTime>
</resultSet>
</spppQueryResponse>
7.17. Get Egree Route
SSP1 wants to verify the last provisioned record for the egress route
called EGR_RTE_01.
Mule, et al. Expires April 25, 2011 [Page 72]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:GetEgrRtesRqstType">
<ns1:objKey>
<rantId>iana-en:111</rantId>
<name>EGR_RTE_01</name>
</ns1:objKey>
</rqst>
</spppQueryRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppQueryResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
<resultSet xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:EgrRteType">
<rantId>iana-en:111</rantId>
<rarId>iana-en:111</rarId>
<egrRteName>EGR_RTE_01</egrRteName>
<pref>50</pref>
<svcs>E2U+sip</svcs>
<regxRewriteRule>
<ere>^(.*)$</ere>
<repl>sip:\1@sbe1.ssp1.example.com</repl>
</regxRewriteRule>
<ingressRte>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</ingressRte>
</resultSet>
</spppQueryResponse>
Mule, et al. Expires April 25, 2011 [Page 73]
Internet-Draft draft-drinks-spprov October 2010
7.18. Delete Destination Group
SSP2 initiates a request to delete the destination group
DEST_GRP_SSP2_1.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DelDestGrpRqstType">
<objKey>
<rantId>iana-en:222</rantId>
<name>DEST_GRP_SSP2_1</name>
</objKey>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<serverTransId>txid-982543123</serverTransId>
<overallResult>
<code>1000</code>
<msg>Success</msg>
</overallResult>
</spppUpdateResponse>
7.19. Delete Public Identity
SSP2 choses to de-activate the TN and remove it from the Registry.
Mule, et al. Expires April 25, 2011 [Page 74]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DelPubIdRqstType">
<pi xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:TNType">
<rantId>iana-en:222</rantId>
<rarId>iana-en:222</rarId>
<tn>+12025556666</tn>
</pi>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<serverTransId>txid-98298273123</serverTransId>
<overallResult>
<code>1000</code>
<msg>success</msg>
</overallResult>
</spppUpdateResponse>
7.20. Delete Route Group Request
SSP2 removes the route group called RTE_GRP_SSP2_1.
Mule, et al. Expires April 25, 2011 [Page 75]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DelRteGrpRqstType">
<objKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</objKey>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<serverTransId>txid-982543123</serverTransId>
<overallResult>
<code>1000</code>
<msg>msg</msg>
</overallResult>
</spppUpdateResponse>
7.21. Delete Route Group Offers Request
SSP2 no longer wants to share route group RTE_GRP_SSP2_1 with SSP1.
Mule, et al. Expires April 25, 2011 [Page 76]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DelRteGrpOfferRqstType">
<rteGrpOfferKey>
<rteGrpKey>
<rantId>iana-en:222</rantId>
<name>RTE_GRP_SSP2_1</name>
</rteGrpKey>
<offeredTo>iana-en:111</offeredTo>
</rteGrpOfferKey>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response. Restoring this resource sharing will require a new route
group offer from SSP2 to SSP1 followed by a successful route group
accept request from SSP1.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<serverTransId>txid-982543123</serverTransId>
<overallResult>
<code>1000</code>
<msg>Success</msg>
</overallResult>
</spppUpdateResponse>
7.22. Delete Egress Route
SSP1 decides to remove the egress route with the label EGR_RTE_01.
Mule, et al. Expires April 25, 2011 [Page 77]
Internet-Draft draft-drinks-spprov October 2010
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateRequest xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<rqst xmlns:ns1="urn:ietf:params:xml:ns:sppp:base:1"
xsi:type="ns1:DelEgrRteRqstType">
<objKey>
<rantId>iana-en:111</rantId>
<name>EGR_RTE_01</name>
</objKey>
</rqst>
</spppUpdateRequest>
Registry completes the request successfully and returns a favorable
response.
<?xml version="1.0" encoding="UTF-8"?>
<spppUpdateResponse xmlns="urn:ietf:params:xml:ns:sppp:base:1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:ietf:params:xml:ns:sppp:base:1 sppp.xsd">
<serverTransId>txid-982543123</serverTransId>
<overallResult>
<code>1000</code>
<msg>Success</msg>
</overallResult>
</spppUpdateResponse>
Mule, et al. Expires April 25, 2011 [Page 78]
Internet-Draft draft-drinks-spprov October 2010
8. XML Considerations
XML serves as the encoding format for SPPP, allowing complex
hierarchical data to be expressed in a text format that can be read,
saved, and manipulated with both traditional text tools and tools
specific to XML.
XML is case sensitive. Unless stated otherwise, XML specifications
and examples provided in this document MUST be interpreted in the
character case presented to develop a conforming implementation.
This section discusses a small number of XML-related considerations
pertaining to SPPP.
8.1. Namespaces
All SPPP protocol elements are defined in the namespaces in te IANA
Considerations section and in the Formal Protocol Specification
section of this document.
8.2. Versioning and Character Encoding
All XML instances SHOULD begin with an <?xml?> declaration to
identify the version of XML that is being used, optionally identify
use of the character encoding used, and optionally provide a hint to
an XML parser that an external schema file is needed to validate the
XML instance.
Conformant XML parsers recognize both UTF-8 (defined in [RFC3629])
and UTF-16 (defined in [RFC2781]); per [RFC2277] UTF-8 is the
RECOMMENDED character encoding for use with SPPP.
Character encodings other than UTF-8 and UTF-16 are allowed by XML.
UTF-8 is the default encoding assumed by XML in the absence of an
"encoding" attribute or a byte order mark (BOM); thus, the "encoding"
attribute in the XML declaration is OPTIONAL if UTF-8 encoding is
used. SPPP clients and servers MUST accept a UTF-8 BOM if present,
though emitting a UTF-8 BOM is NOT RECOMMENDED.
Example XML declarations:
<?xml?> version="1.0" encoding="UTF-8" standalone="no"?>
Mule, et al. Expires April 25, 2011 [Page 79]
Internet-Draft draft-drinks-spprov October 2010
9. Security Considerations
The transport protocol section contains some security properties that
the transport protocol must provide so that authenticated endpoints
can exchange data confidentially and with integrity protection.
More details will be provided in a future revision of this document.
Mule, et al. Expires April 25, 2011 [Page 80]
Internet-Draft draft-drinks-spprov October 2010
10. IANA Considerations
This document uses URNs to describe XML namespaces and XML schemas
conforming to a registry mechanism described in [RFC3688].
Two URI assignments are requested.
Registration request for the SPPP XML namespace:
urn:ietf:params:xml:ns:sppp:base:1
Registrant Contact: IESG
XML: None. Namespace URIs do not represent an XML specification.
Registration request for the XML schema:
URI: urn:ietf:params:xml:schema:sppp:1
Registrant Contact: IESG
XML: See the "Formal Specification" section of this document
(Section 11).
IANA is requested to create a new SPPP registry for Organization
Identifiers that will indicate valid strings to be used for well-
known enterprise namespaces.
This document makes the following assignments for the OrgIdType
namespaces:
Namespace OrgIdType namespace string
---- ----------------------------
IANA Enterprise Numbers iana-en
Mule, et al. Expires April 25, 2011 [Page 81]
Internet-Draft draft-drinks-spprov October 2010
11. Formal Specification
This section provides the draft XML Schema Definition for the SPPP
protocol.
<?xml version="1.0" encoding="UTF-8"?>
<schema xmlns:spppb="urn:ietf:params:xml:ns:sppp:base:1"
xmlns="http://www.w3.org/2001/XMLSchema"
targetNamespace="urn:ietf:params:xml:ns:sppp:base:1"
elementFormDefault="qualified" xml:lang="EN">
<annotation>
<documentation>
------------------ Object Type Definitions --------------
</documentation>
</annotation>
<complexType name="RteGrpType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rteGrpName" type="spppb:ObjNameType"/>
<element name="rteRecRef" type="spppb:RteRecRefType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="dgName" type="spppb:ObjNameType" minOccurs="0"
maxOccurs="unbounded"/>
<element name="peeringOrg" type="spppb:OrgIdType" minOccurs="0"
maxOccurs="unbounded"/>
<element name="sourceIdent" type="spppb:SourceIdentType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="isInSvc" type="boolean"/>
<element name="priority" type="unsignedShort"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DestGrpType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="dgName" type="spppb:ObjNameType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="PubIdType" abstract="true">
<complexContent>
Mule, et al. Expires April 25, 2011 [Page 82]
Internet-Draft draft-drinks-spprov October 2010
<extension base="spppb:BasicObjType">
<sequence>
<element name="dgName" type="spppb:ObjNameType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="EmailType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="email" type="string"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="TNType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="tn" type="string"/>
<element name="rteRecRef" type="spppb:RteRecRefType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="TNRType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="startTn" type="string"/>
<element name="endTn" type="string"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
<attribute name="prefix" type="boolean" default="false">
</attribute>
</extension>
</complexContent>
</complexType>
<complexType name="TNPType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="tnPrefix" type="string"/>
Mule, et al. Expires April 25, 2011 [Page 83]
Internet-Draft draft-drinks-spprov October 2010
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RNType">
<complexContent>
<extension base="spppb:PubIdType">
<sequence>
<element name="rn" type="string" default="true"/>
<element name="corInfo" type="spppb:CORInfoType"
minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RteRecType" abstract="true">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rrName" type="spppb:ObjNameType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="NAPTRType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="order" type="unsignedShort"/>
<element name="flags" type="string" minOccurs="0"/>
<element name="svcs" type="string"/>
<element name="regx" type="spppb:RegexParamType"
minOccurs="0"/>
<element name="repl" type="string" minOccurs="0"/>
<element name="ttl" type="positiveInteger" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="NSType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="hostName" type="string"/>
<element name="ipAddr" type="spppb:IPAddrType" minOccurs="0"
Mule, et al. Expires April 25, 2011 [Page 84]
Internet-Draft draft-drinks-spprov October 2010
maxOccurs="unbounded"/>
<element name="ttl" type="positiveInteger" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="URIType">
<complexContent>
<extension base="spppb:RteRecType">
<sequence>
<element name="ere" type="string" default="^(.*)$"/>
<element name="uri" type="string"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RteGrpOfferType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="rteGrpOfferKey" type="spppb:RteGrpOfferKeyType"
/>
<element name="status" type="spppb:RteGrpOfferStatusType"/>
<element name="offerDateTime" type="dateTime"/>
<element name="acceptDateTime" type="dateTime" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="EgrRteType">
<complexContent>
<extension base="spppb:BasicObjType">
<sequence>
<element name="egrRteName" type="spppb:ObjNameType"/>
<element name="pref" type="unsignedShort"/>
<element name="regxRewriteRule" type="spppb:RegexParamType"/>
<element name="ingrRteRec" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</extension>
</complexContent>
</complexType>
<annotation>
<documentation> ------------------ Abstract Object and Element
Mule, et al. Expires April 25, 2011 [Page 85]
Internet-Draft draft-drinks-spprov October 2010
Type Definitions -------------- </documentation>
</annotation>
<complexType name="BasicObjType" abstract="true">
<sequence>
<element name="rantId" type="spppb:OrgIdType"/>
<element name="rarId" type="spppb:OrgIdType"/>
<element name="crtDate" type="dateTime" minOccurs="0"/>
<element name="modDate" type="dateTime" minOccurs="0"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<complexType name="RegexParamType">
<sequence>
<element name="ere" type="string" default="^(.*)$"/>
<element name="repl" type="string"/>
</sequence>
</complexType>
<simpleType name="OrgIdType">
<restriction base="string"/>
</simpleType>
<simpleType name="ObjNameType">
<restriction base="string"/>
</simpleType>
<simpleType name="TransIdType">
<restriction base="string"/>
</simpleType>
<simpleType name="MinorVerType">
<restriction base="unsignedLong"/>
</simpleType>
<complexType name="ObjKeyType">
<sequence>
<element name="rantId" type="spppb:OrgIdType"/>
<element name="name" type="spppb:ObjNameType"/>
</sequence>
</complexType>
<complexType name="IPAddrType">
<sequence>
<element name="addr" type="string"/>
<element name="type" type="spppb:IPType"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<simpleType name="IPType">
<restriction base="token">
<enumeration value="IPv4"/>
<enumeration value="IPv6"/>
</restriction>
</simpleType>
Mule, et al. Expires April 25, 2011 [Page 86]
Internet-Draft draft-drinks-spprov October 2010
<complexType name="RteRecRefType">
<sequence>
<element name="rteRec" type="spppb:ObjKeyType"/>
<element name="priority" type="unsignedShort"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<complexType name="SourceIdentType">
<sequence>
<element name="sourceIdentLabel" type="string"/>
<element name="sourceIdentScheme"
type="spppb:SourceIdentSchemeType"/>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<simpleType name="SourceIdentSchemeType">
<restriction base="token">
<enumeration value="uri"/>
<enumeration value="ip"/>
<enumeration value="rootDomain"/>
</restriction>
</simpleType>
<complexType name="CORInfoType">
<sequence>
<element name="corClaim" type="boolean" default="true"/>
<element name="cor" type="boolean" default="false"
minOccurs="0"/>
<element name="corDateTime" type="dateTime" minOccurs="0"/>
</sequence>
</complexType>
<complexType name="SvcMenuType">
<sequence>
<element name="serverStatus" type="spppb:ServerStatusType"/>
<element name="majMinVersion" type="string"
maxOccurs="unbounded"/>
<element name="objURI" type="anyURI" maxOccurs="unbounded"/>
<element name="extURI" type="anyURI" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</complexType>
<simpleType name="ServerStatusType">
<restriction base="token">
<enumeration value="inService"/>
<enumeration value="outOfService"/>
</restriction>
</simpleType>
<complexType name="RteGrpOfferKeyType">
<sequence>
Mule, et al. Expires April 25, 2011 [Page 87]
Internet-Draft draft-drinks-spprov October 2010
<element name="rteGrpKey" type="spppb:ObjKeyType"/>
<element name="offeredTo" type="spppb:OrgIdType"/>
</sequence>
</complexType>
<simpleType name="RteGrpOfferStatusType">
<restriction base="token">
<enumeration value="offered"/>
<enumeration value="accepted"/>
</restriction>
</simpleType>
<complexType name="ExtAnyType">
<sequence>
<any namespace="##other" maxOccurs="unbounded"/>
</sequence>
</complexType>
<annotation>
<documentation> -------------- Operation Request and Response
Object Type Definitions ------------ </documentation>
</annotation>
<complexType name="ResultCodeType">
<sequence>
<element name="code" type="int"/>
<element name="msg" type="string"/>
</sequence>
</complexType>
<complexType name="RqstObjResultCodeType">
<complexContent>
<extension base="spppb:ResultCodeType">
<sequence>
<element name="rqstObj" type="spppb:BasicRqstType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="BasicRqstType" abstract="true">
<sequence>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<complexType name="BasicQueryRqstType" abstract="true">
<sequence>
<element name="ext" type="spppb:ExtAnyType" minOccurs="0"/>
</sequence>
</complexType>
<complexType name="AddRteGrpRqstType">
<complexContent>
Mule, et al. Expires April 25, 2011 [Page 88]
Internet-Draft draft-drinks-spprov October 2010
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrp" type="spppb:RteGrpType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelRteGrpRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetRteGrpsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AddRteRecRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteRec" type="spppb:RteRecType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelRteRecRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetRteRecsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
Mule, et al. Expires April 25, 2011 [Page 89]
Internet-Draft draft-drinks-spprov October 2010
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AddDestGrpRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="destGrp" type="spppb:DestGrpType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelDestGrpRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetDestGrpsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AddPubIdRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="pi" type="spppb:PubIdType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelPubIdRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
Mule, et al. Expires April 25, 2011 [Page 90]
Internet-Draft draft-drinks-spprov October 2010
<element name="pi" type="spppb:PubIdType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetPubIdsRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="pi" type="spppb:PubIdType" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AddRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOffer" type="spppb:RteGrpOfferType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType" />
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AcceptRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="RejectRteGrpOfferRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
Mule, et al. Expires April 25, 2011 [Page 91]
Internet-Draft draft-drinks-spprov October 2010
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetRteGrpOffersRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="offeredByPeers" type="boolean"
minOccurs="0"/>
<element name="offeredToPeers" type="boolean"
minOccurs="0"/>
<element name="status" type="spppb:RteGrpOfferStatusType"
minOccurs="0"/>
<element name="peeringOrg" type="spppb:OrgIdType"
minOccurs="0" maxOccurs="unbounded"/>
<element name="rteGrpOfferKey"
type="spppb:RteGrpOfferKeyType" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="AddEgrRteRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="egrRte" type="spppb:EgrRteType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="DelEgrRteRqstType">
<complexContent>
<extension base="spppb:BasicRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"/>
</sequence>
</extension>
</complexContent>
</complexType>
<complexType name="GetEgrRtesRqstType">
<complexContent>
<extension base="spppb:BasicQueryRqstType">
<sequence>
<element name="objKey" type="spppb:ObjKeyType"
Mule, et al. Expires April 25, 2011 [Page 92]
Internet-Draft draft-drinks-spprov October 2010
minOccurs="0" maxOccurs="unbounded"/>
</sequence>
</extension>
</complexContent>
</complexType>
<annotation>
<documentation> -------- Generic Request and Response Definitions
--------------- </documentation>
</annotation>
<element name="spppUpdateRequest">
<complexType>
<sequence>
<element name="clientTransId" type="spppb:TransIdType"
minOccurs="0"/>
<element name="minorVer" type="spppb:MinorVerType"
minOccurs="0"/>
<element name="rqst" type="spppb:BasicRqstType"
maxOccurs="unbounded"/>
</sequence>
</complexType>
</element>
<element name="spppUpdateResponse">
<complexType>
<sequence>
<element name="clientTransId" type="spppb:TransIdType"
minOccurs="0"/>
<element name="serverTransId" type="spppb:TransIdType"/>
<element name="overallResult" type="spppb:ResultCodeType"/>
<element name="rqstObjResult"
type="spppb:RqstObjResultCodeType" minOccurs="0"
maxOccurs="unbounded"/>
</sequence>
</complexType>
</element>
<element name="spppQueryRequest">
<complexType>
<sequence>
<element name="minorVer" type="spppb:MinorVerType"
minOccurs="0"/>
<element name="rqst" type="spppb:BasicQueryRqstType"/>
</sequence>
</complexType>
</element>
<element name="spppQueryResponse">
<complexType>
<sequence>
<element name="overallResult" type="spppb:ResultCodeType"/>
<element name="resultSet" type="spppb:BasicObjType"
Mule, et al. Expires April 25, 2011 [Page 93]
Internet-Draft draft-drinks-spprov October 2010
minOccurs="0" maxOccurs=" unbounded"/>
</sequence>
</complexType>
</element>
<element name="spppServerStatusRequest">
<complexType>
<sequence>
<element name="minorVer" type="spppb:MinorVerType"
minOccurs="0"/>
</sequence>
</complexType>
</element>
<element name="spppServerStatusResponse">
<complexType>
<sequence>
<element name="overallResult" type="spppb:ResultCodeType"/>
<element name="svcMenu" type="spppb:SvcMenuType"/>
</sequence>
</complexType>
</element>
</schema>
Mule, et al. Expires April 25, 2011 [Page 94]
Internet-Draft draft-drinks-spprov October 2010
12. Specification Extensibility
The protocol defined in this specification is extensible. This
section explains how to extend the protocol and what procedures are
necessary to follow in order to ensure proper extensions.
Mule, et al. Expires April 25, 2011 [Page 95]
Internet-Draft draft-drinks-spprov October 2010
13. Acknowledgments
This document is a result of various discussions held in the DRINKS
working group and within the DRINKS protocol design team, which is
comprised of the following individuals, in alphabetical order:
Alexander Mayrhofer, Deborah A Guyton, David Schwartz, Lisa
Dusseault, Manjul Maharishi, Otmar Lendl, Richard Shockey and Sumanth
Channabasappa.
Mule, et al. Expires April 25, 2011 [Page 96]
Internet-Draft draft-drinks-spprov October 2010
14. References
14.1. Normative References
[I-D.ietf-drinks-sppp-over-soap]
Cartwright, K., "SPPP Over SOAP and HTTP",
draft-ietf-drinks-sppp-over-soap-00 (work in progress),
June 2010.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2277] Alvestrand, H., "IETF Policy on Character Sets and
Languages", BCP 18, RFC 2277, January 1998.
[RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO
10646", STD 63, RFC 3629, November 2003.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66,
RFC 3986, January 2005.
14.2. Informative References
[I-D.ietf-drinks-usecases-requirements]
Channabasappa, S., "DRINKS Use cases and Protocol
Requirements", draft-ietf-drinks-usecases-requirements-03
(work in progress), May 2010.
[RFC2781] Hoffman, P. and F. Yergeau, "UTF-16, an encoding of ISO
10646", RFC 2781, February 2000.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC3761] Faltstrom, P. and M. Mealling, "The E.164 to Uniform
Resource Identifiers (URI) Dynamic Delegation Discovery
System (DDDS) Application (ENUM)", RFC 3761, April 2004.
[RFC4725] Mayrhofer, A. and B. Hoeneisen, "ENUM Validation
Architecture", RFC 4725, November 2006.
[RFC5321] Klensin, J., "Simple Mail Transfer Protocol", RFC 5321,
Mule, et al. Expires April 25, 2011 [Page 97]
Internet-Draft draft-drinks-spprov October 2010
October 2008.
[RFC5486] Malas, D. and D. Meyer, "Session Peering for Multimedia
Interconnect (SPEERMINT) Terminology", RFC 5486,
March 2009.
Mule, et al. Expires April 25, 2011 [Page 98]
Internet-Draft draft-drinks-spprov October 2010
Authors' Addresses
Jean-Francois Mule
CableLabs
858 Coal Creek Circle
Louisville, CO 80027
USA
Email: jfm@cablelabs.com
Kenneth Cartwright
TNS
1939 Roland Clarke Place
Reston, VA 20191
USA
Email: kcartwright@tnsi.com
Syed Wasim Ali
NeuStar
46000 Center Oak Plaza
Sterling, VA 20166
USA
Email: syed.ali@neustar.biz
Alexander Mayrhofer
enum.at GmbH
Karlsplatz 1/9
Wien, A-1010
Austria
Email: alexander.mayrhofer@enum.at
Mule, et al. Expires April 25, 2011 [Page 99]
