Email Address Internationalization Y. Abel
(EAI) TWNIC
Internet-Draft S. Steele
Obsoletes: 5335 (if approved) Microsoft
Updates: 2045,5321,5322 December 04, 2010
(if approved)
Intended status: Standards Track
Expires: June 7, 2011
Internationalized Email Headers
draft-ietf-eai-rfc5335bis-05
Abstract
Full internationalization of electronic mail requires not only the
capabilities to transmit non-ASCII content, to encode selected
information in specific header fields, and to use non-ASCII
characters in envelope addresses. It also requires being able to
express those addresses and the information based on them in mail
header fields. This document specifies a variant of Internet mail
that permits the use of Unicode encoded in UTF-8, rather than ASCII,
as the base form for Internet email header field. This form is
permitted in transmission only if authorized by an SMTP extension, as
specified in an associated specification. This specification updates
Section 6.4 of [RFC2045] to conform with the requirements.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 7, 2011.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
Abel & Steele Expires June 7, 2011 [Page 1]
Internet-Draft I18N Email Headers December 2010
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Role of This Specification . . . . . . . . . . . . . . . . 3
1.2. Relation to Other Standards . . . . . . . . . . . . . . . 3
2. Background and History . . . . . . . . . . . . . . . . . . . . 3
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Changes on Message Header Fields . . . . . . . . . . . . . . . 5
4.1. UTF-8 Syntax and Normalization . . . . . . . . . . . . . . 5
4.2. Changes on MIME Headers . . . . . . . . . . . . . . . . . 5
4.3. Syntax Extensions to RFC 5322 . . . . . . . . . . . . . . 6
4.4. Change on addr-spec Syntax . . . . . . . . . . . . . . . . 8
4.5. Trace Field Syntax . . . . . . . . . . . . . . . . . . . . 9
4.6. message/global . . . . . . . . . . . . . . . . . . . . . . 9
5. Security Considerations . . . . . . . . . . . . . . . . . . . 11
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 12
8. Edit history . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.1. draft-ietf-eai-rfc5335bis-00 . . . . . . . . . . . . . . . 12
8.2. draft-ietf-eai-rfc5335bis-01 . . . . . . . . . . . . . . . 12
8.3. draft-ietf-eai-rfc5335bis-02 . . . . . . . . . . . . . . . 12
8.4. draft-ietf-eai-rfc5335bis-03 . . . . . . . . . . . . . . . 12
8.5. draft-ietf-eai-rfc5335bis-04 . . . . . . . . . . . . . . . 13
8.6. draft-ietf-eai-rfc5335bis-05 . . . . . . . . . . . . . . . 13
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9.1. Normative References . . . . . . . . . . . . . . . . . . . 13
9.2. Informative References . . . . . . . . . . . . . . . . . . 14
Abel & Steele Expires June 7, 2011 [Page 2]
Internet-Draft I18N Email Headers December 2010
1. Introduction
1.1. Role of This Specification
Full internationalization of electronic mail requires several
capabilities:
o The capability to transmit non-ASCII content, provided for as part
of the basic MIME specification [RFC2045], [RFC2046].
o The capability to use international characters in envelope
addresses, discussed in [I-D.ietf-eai-frmwrk-4952bis] and
specified in [I-D.ietf-eai-rfc5336bis].
o The capability to express those addresses, and information related
to them and based on them, in mail header fields, defined in this
document.
This document specifies a variant of Internet mail that permits the
use of Unicode encoded in UTF-8 [RFC3629], rather than ASCII, as the
base form for Internet email header fields. This form is permitted
in transmission, if authorized by the SMTP extension specified in
[I-D.ietf-eai-rfc5336bis] or by other transport mechanisms capable of
processing it.
1.2. Relation to Other Standards
This document updates Section 6.4 of [RFC2045]. It removes the
blanket ban on applying a content-transfer-encoding to all subtypes
of message/ and instead specifies that a composite subtype MAY
specify whether or not a content-transfer-encoding can be used for
that subtype, with "cannot be used" as the default.
This document also updates Section 3.4 of [RFC5322]. It Extended
mailbox address syntax to permit UTF-8 character in Section 4.3.
Allowing use of a content-transfer-encoding on subtypes of messages
is not limited to transmissions that are authorized by the SMTP
extension specified in [I-D.ietf-eai-rfc5336bis]. message/global (see
Section 4.6) permits use of a content-transfer-encoding.
2. Background and History
Mailbox names often represent the names of human users. Many of
these users throughout the world have names that are not normally
expressed with just the ASCII repertoire of characters, and would
like to use more or less their real names in their mailbox names.
These users are also likely to use non-ASCII text in their display
Abel & Steele Expires June 7, 2011 [Page 3]
Internet-Draft I18N Email Headers December 2010
names and subjects of email messages, both received and sent. This
protocol specifies UTF-8 as the encoding to represent email header
field bodies.
The traditional format of email messages [RFC5322] allows only ASCII
characters in the header fields of messages. This prevents users
from having email addresses that contain non-ASCII characters. It
further forces non-ASCII text in display names, comments, and in free
text (such as in the "Subject:" field) to be encoded (as required by
MIME format [RFC2047]). This specification describes a change to the
email message format that is related to the SMTP message transport
change described in the associated documents
[I-D.ietf-eai-frmwrk-4952bis] and [I-D.ietf-eai-rfc5336bis], and that
allows non-ASCII characters in most email header fields. These
changes affect SMTP clients, SMTP servers, mail user agents (MUAs),
list expanders, gateways to other media, and all other processes that
parse or handle email messages.
As specified in [I-D.ietf-eai-rfc5336bis], an SMTP protocol extension
"UTF8SMTPbis" is used to prevent the transmission of messages with
UTF-8 header fields to systems that cannot handle such messages.
Use of this SMTP extension helps prevent the introduction of such
messages into message stores that might misinterpret, improperly
display, or mangle such messages. It should be noted that using an
ESMTP extension does not prevent transferring email messages with
UTF-8 header fields to other systems that use the email format for
messages and that may not be upgraded, such as unextended POP and
IMAP servers. Changes to these protocols to handle UTF-8 header
fields are addressed in [I-D.ietf-eai-rfc5721bis] and
[I-D.ietf-eai-5378bis].
The objective for this protocol is to allow UTF-8 in email header
fields.
3. Terminology
A plain ASCII string is full compatible with [RFC5321] and [RFC5322].
In this document, non-ASCII strings are UTF-8 strings if they are in
header which contain at least one <UTF8-non-ascii>.
Unless otherwise noted, all terms used here are defined in [RFC5321],
[RFC5322], [I-D.ietf-eai-frmwrk-4952bis], or
[I-D.ietf-eai-rfc5336bis].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Abel & Steele Expires June 7, 2011 [Page 4]
Internet-Draft I18N Email Headers December 2010
4. Changes on Message Header Fields
SMTP clients can send header fields in UTF-8 format, if the
UTF8SMTPbis extension is advertised by the SMTP server or is
permitted by other transport mechanisms.
This protocol does NOT change the [RFC5322] rules for defining header
field names. The bodies of header fields are allowed to contain
UTF-8 characters, but the header field names themselves must contain
only ASCII characters.
To permit UTF-8 characters in field values, the header definition in
[RFC5322] is extended to support the new format. The following ABNF
is defined to substitute those definitions in [RFC5322].
The syntax rules not covered in this section remain as defined in
[RFC5322].
4.1. UTF-8 Syntax and Normalization
UTF-8 characters can be defined in terms of octets using the
following ABNF [RFC5234], taken from [RFC3629]:
UTF8-non-ascii = UTF8-2 / UTF8-3 / UTF8-4
UTF8-2 = <See Section 4 of RFC3629>
UTF8-3 = <See Section 4 of RFC3629>
UTF8-4 = <See Section 4 of RFC3629>
See [RFC5198] for a discussion of normalization; the use of
normalization form [NFC] is RECOMMENDED. Actually, if one is going
to do internationalization properly, one of the most often-cited
goals is to permit people to spell their names correctly. Since many
mailbox local parts reflect personal names, that principle applies as
well. And NFKC is not recommended because it may lose information
that is needed to correctly spell some names in unusual
circumstances.
4.2. Changes on MIME Headers
This specification updates Section 6.4 of [RFC2045]. [RFC2045]
prohibits applying a content-transfer-encoding to any subtypes of
"message/". This specification relaxes the rule -- it allows newly
defined MIME types to permit content-transfer-encoding, and it allows
content-transfer-encoding for message/global (see Section 4.6).
Abel & Steele Expires June 7, 2011 [Page 5]
Internet-Draft I18N Email Headers December 2010
Background: Normally, transfer of message/global will be done in
8-bit-clean channels, and body parts will have "identity" encodings,
that is, no decoding is necessary. In the case where a message
containing a message/global is downgraded from 8-bit to 7-bit as
described in [RFC1652], an encoding may be applied to the message; if
the message travels multiple times between a 7-bit environment and an
environment implementing UTF8SMTPbis, multiple levels of encoding may
occur. This is expected to be rarely seen in practice, and the
potential complexity of other ways of dealing with the issue are
thought to be larger than the complexity of allowing nested encodings
where necessary.
4.3. Syntax Extensions to RFC 5322
The following rules are intended to extend the corresponding rules in
[RFC5322] in order to allow UTF-8 characters.
FWS = <see [RFC5322] Section 3.2.2, folding white space>
CFWS = <see [RFC5322] Section 3.2.2>
ctext =/ UTF8-non-ascii
comment = "(" *([FWS] uCcontent) [FWS] ")"
word = uAtom / uQuoted-String
This means that all the [RFC5322] constructs that build upon these
will permit UTF-8 characters, including comments and quoted strings.
We do not change the syntax of <atext> in order to allow UTF-8
characters in <addr-spec>. This would also allow UTF-8 characters in
<message-id>, which is not allowed due to the limitation described in
Section 4.5. Instead, <uAtext> is added to meet this requirement.
Abel & Steele Expires June 7, 2011 [Page 6]
Internet-Draft I18N Email Headers December 2010
uText = %d1-9 / ; all UTF-8 characters except
%d11-12 / ; US-ASCII NUL, CR, and LF
%d14-127 /
UTF8-non-ascii
uQuoted-Pair = ("\" (VCHAR / WSP / UTF8-non-ascii )) / obs-qp
VCHAR = <See appendix B.1 of RFC 5234>
WSP = <See appendix B.1 of RFC 5234>
uQcontent = uQtext / uQuoted-Pair
uQuoted-Pair = ("\" uText) / obs-qp
DQUOTE = <See appendix B.1 of RFC 5234>
uCcontent = ctext / uQuoted-Pair / comment
uQtext = qtext / UTF8-non-ascii
uAtext = ALPHA / DIGIT /
"!" / "#" / ; Any character except
"$" / "%" / ; controls, SP, and specials.
"&" / "'" / ; Used for atoms.
"*" / "+" /
"-" / "/" /
"=" / "?" /
"^" / "_" /
"`" / "{" /
"|" / "}" /
"~" /
UTF8-non-ascii
uAtom = [CFWS] 1*uAtext [CFWS]
uDot-Atom = [CFWS] uDot-Atom-text [CFWS]
uDot-Atom-text = 1*uAtext *("." 1*uAtext)
qcontent =/ uQcontent
To allow the use of UTF-8 in a Content-Description header field
[RFC2045], the following syntax is used:
description = "Content-Description" ":" *uText
Abel & Steele Expires June 7, 2011 [Page 7]
Internet-Draft I18N Email Headers December 2010
; Replace description in Section 8 of [RFC2045]
The <uText> syntax is extended above to allow UTF-8 in all
<description> header fields.
Note, however, this does not remove any constraint on the character
set of protocol elements; for instance, all the allowed values for
timezone in the "Date:" header fields are still expressed in ASCII.
And also, none of this revised syntax changes what is allowed in a
<msg-id>, which will still remain in pure ASCII.
4.4. Change on addr-spec Syntax
Internationalized email addresses are represented in UTF-8. Thus,
all header fields containing <mailbox>es are updated from [RFC5321]
Section 4.1.2 to permit UTF-8 addresses.
mailbox = name-addr / addr-spec / uAddr-Spec
; Replace mailbox in Section 3.4 of RFC 5322
angle-addr =/ [CFWS] "<" uAddr-Spec ">" [CFWS]
; Replace angle-addr in Section 3.4 of RFC 5322
uAddr-Spec = uLocal-Part "@" uDomain
uLocal-Part = uDot-Atom / uQuoted-String / obs-local-part
; Replace Local-Part in Section 3.4.1 of RFC 5322
uDomain = uDot-Atom / domain-literal / obs-domain
domain-literal = <See Section 3.4.1 of RFC 5322>
Below are a few examples of possible <mailbox> representations.
"DISPLAY_NAME" <ASCII@ASCII>
; traditional mailbox format
"DISPLAY_NAME" <non-ASCII@non-ASCII>
; message will be rejected if UTF8SMTPbis extension is not supported
<non-ASCII@non-ASCII>
; without DISPLAY_NAME and quoted string
; message will be rejected if UTF8SMTPbis extension is not supported
Abel & Steele Expires June 7, 2011 [Page 8]
Internet-Draft I18N Email Headers December 2010
4.5. Trace Field Syntax
The 'uFor' clause in "Received:" fields has been allowed the use of
internationalized addresses in "For" fields. It described in
[I-D.ietf-eai-rfc5336bis], Section 3.6.3.
The "Return-path" designates the address to which messages indicating
non-delivery or other mail system failures are to be sent. Thus, the
header is augmented to carry UTF-8 addresses (see the revised syntax
of <angle-addr> in Section 4.4 of this document). This will not
break the rule of trace field integrity, because the header field is
added at the last MTA and described in [RFC5321].
The <received-token> on "Received:" field ( described in Section
3.6.7 of [RFC5322]) syntax is augmented to allow UTF-8 email address
in the "For" field. <angle-addr> is augmented to include UTF-8 email
address. In order to allow UTF-8 email addresses in an <addr-spec>,
<uAddr-Spec> is added to <received-token>.
received-token =/ uAddr-Spec
4.6. message/global
Internationalized messages MUST only be transmitted as authorized by
[I-D.ietf-eai-rfc5336bis] or within a non-SMTP environment which
supports these messages. A message is a "message/global message", if
o it contains UTF-8 header values as specified in this document, or
o it contains UTF-8 values in the headers fields of body parts.
The type message/global is similar to message/rfc822, except that it
specifies that a message can contain UTF-8 characters in the headers
of the message or body parts. If this type is sent to a 7-bit-only
system, it has to be encoded in MIME [RFC2045]. (Note that a system
compliant with MIME that doesn't recognize message/global SHOULD
treat it as "application/octet-stream" as described in Section 5.2.4
of [RFC2046].)
Type name: message
Subtype name: global
Required parameters: none
Abel & Steele Expires June 7, 2011 [Page 9]
Internet-Draft I18N Email Headers December 2010
Optional parameters: none
Encoding considerations: Any content-transfer-encoding is permitted.
The 8-bit or binary content-transfer-encodings are recommended
where permitted.
Security considerations: See Section 5.
Interoperability considerations: The media type provides
functionality similar to the message/rfc822 content type for email
messages with international email headers. When there is a need
to embed or return such content in another message, there is
generally an option to use this media type and leave the content
unchanged or down-convert the content to message/rfc822. Both of
these choices will interoperate with the installed base, but with
different properties. Systems unaware of internationalized
headers will typically treat a message/global body part as an
unknown attachment, while they will understand the structure of a
message/rfc822. However, systems that understand message/global
will provide functionality superior to the result of a down-
conversion to message/rfc822. The most interoperable choice
depends on the deployed software.
Published specification: RFC XXXX
Applications that use this media type: SMTP servers and email
clients that support multipart/report generation or parsing.
Email clients which forward messages with international headers as
attachments.
Additional information:
Magic number(s): none
File extension(s): The extension ".u8msg" is suggested.
Macintosh file type code(s): A uniform type identifier (UTI) of
"public.utf8-email-message" is suggested. This conforms to
"public.message" and "public.composite-content", but does not
necessarily conform to "public.utf8-plain-text".
Person & email address to contact for further information: See the
Author's Address section of this document.
Intended usage: COMMON
Abel & Steele Expires June 7, 2011 [Page 10]
Internet-Draft I18N Email Headers December 2010
Restrictions on usage: This is a structured media type which embeds
other MIME media types. The 8-bit or binary content-transfer-
encoding SHOULD be used unless this media type is sent over a
7-bit-only transport.
Author: See the Author's Address section of this document.
Change controller: IETF Standards Process
5. Security Considerations
If a user has a non-ASCII mailbox address and an ASCII mailbox
address, a digital certificate that identifies that user may have
both addresses in the identity. Having multiple email addresses as
identities in a single certificate is already supported in PKIX
(Public Key Infrastructure for X.509 Certificates) [RFC5280] and
OpenPGP [RFC3156].
Because UTF-8 often requires several octets to encode a single
character, internationalized local parts and header value may cause
mail addresses to become longer. As specified in [RFC5322], each
line of characters MUST be no more 998 octets, excluding the CRLF.
On the other hand, MDA (Mail Delivery Agent) processes that parse,
store, or handle email addresses or local parts must take extra care
not to overflow buffers, truncate addresses, or exceed storage
allotments. Also, they must take care, when comparing, to use the
entire lengths of the addresses.
In this specification, a user could provide an ASCII alternative
address for a non-ASCII address. However, it is possible these two
addresses go to different mailboxes, or even different people. This
configuration may be based on a user's personal choice or on
administration policy. We recognize that if ASCII and non-ASCII
email is delivered to two different destinations, based on MTA
capability, this may violate the principle of least astonishment, but
this is not a "protocol problem".
The security impact of UTF-8 headers on email signature systems such
as Domain Keys Identified Mail (DKIM), S/MIME, and OpenPGP is
discussed in [I-D.ietf-eai-frmwrk-4952bis], Section 14.
6. IANA Considerations
IANA has registered the message/global MIME type using the
registration form contained in Section 4.4.
Abel & Steele Expires June 7, 2011 [Page 11]
Internet-Draft I18N Email Headers December 2010
7. Acknowledgements
This document incorporates many ideas first described in Internet-
Draft form by Paul Hoffman, although many details have changed from
that earlier work.
The author especially thanks Jeff Yeh for his efforts and
contributions on editing previous versions.
Most of the content of this document is provided by John C Klensin.
Also, some significant comments and suggestions were received from
Charles H. Lindsey, Kari Hurtta, Pete Resnick, Alexey Melnikov, Chris
Newman, Yangwoo Ko, Yoshiro Yoneya, and other members of the JET team
(Joint Engineering Team) and were incorporated into the document.
The editor sincerely thanks them for their contributions.
8. Edit history
This section is used for tracking the update of this document. Will
be removed after finalize.
8.1. draft-ietf-eai-rfc5335bis-00
1. Applied Errata suggested by Alfred Hoenes.
2. Adjust [RFC2821] and [RFC2822] to [RFC5321] and [RFC5322].
3. Abrogate <alt-address> in ABNF of <angle-addr>.
4. Revoke [RFC5504] from this document.
5. Upgrade some references from I-Ds to RFC.
8.2. draft-ietf-eai-rfc5335bis-01
1. Author name revised.
8.3. draft-ietf-eai-rfc5335bis-02
1. ABNF revised.
8.4. draft-ietf-eai-rfc5335bis-03
1. Fix typos
2. ABNF revised
Abel & Steele Expires June 7, 2011 [Page 12]
Internet-Draft I18N Email Headers December 2010
3. Improve sentence
8.5. draft-ietf-eai-rfc5335bis-04
1. improve sentences and ABNF revised based on AD and Co-chairs
8.6. draft-ietf-eai-rfc5335bis-05
1. ABNF revised in Section 4.4 based on AD comments
9. References
9.1. Normative References
[I-D.ietf-eai-5378bis] Resnick, P., Newman, C., and S. Shen,
"IMAP Support for UTF-8",
draft-ietf-eai-5378bis-00 (work in
progress), November 2010.
[I-D.ietf-eai-frmwrk-4952bis] Klensin, J. and Y. Ko, "Overview and
Framework for Internationalized
Email",
draft-ietf-eai-frmwrk-4952bis-10 (work
in progress), September 2010.
[I-D.ietf-eai-rfc5336bis] Yao, J. and W. MAO, "SMTP Extension
for Internationalized Email Address",
draft-ietf-eai-rfc5336bis-05 (work in
progress), December 2010.
[I-D.ietf-eai-rfc5721bis] Gellens, R., Newman, C., Yao, J., and
K. Fujiwara, "POP3 Support for UTF-8",
draft-ietf-eai-rfc5721bis-00 (work in
progress), September 2010.
[RFC2119] Bradner, S., "Key words for use in
RFCs to Indicate Requirement Levels",
BCP 14, RFC 2119, March 1997.
[RFC3629] Yergeau, F., "UTF-8, a transformation
format of ISO 10646", STD 63,
RFC 3629, November 2003.
[RFC5198] Klensin, J. and M. Padlipsky, "Unicode
Format for Network Interchange",
RFC 5198, March 2008.
[RFC5234] Crocker, D. and P. Overell, "Augmented
Abel & Steele Expires June 7, 2011 [Page 13]
Internet-Draft I18N Email Headers December 2010
BNF for Syntax Specifications: ABNF",
STD 68, RFC 5234, January 2008.
[RFC5321] Klensin, J., "Simple Mail Transfer
Protocol", RFC 5321, October 2008.
[RFC5322] Resnick, P., Ed., "Internet Message
Format", RFC 5322, October 2008.
9.2. Informative References
[NFC] Davis, M. and K. Whistler, "Unicode
Standard Annex #15: Unicode
Normalization Forms", September 2010,
<http://www.unicode.org/reports/
tr15/>.
[RFC1652] Klensin, J., Freed, N., Rose, M.,
Stefferud, E., and D. Crocker, "SMTP
Service Extension for 8bit-
MIMEtransport", RFC 1652, July 1994.
[RFC2045] Freed, N. and N. Borenstein,
"Multipurpose Internet Mail Extensions
(MIME) Part One: Format of Internet
Message Bodies", RFC 2045,
November 1996.
[RFC2046] Freed, N. and N. Borenstein,
"Multipurpose Internet Mail Extensions
(MIME) Part Two: Media Types",
RFC 2046, November 1996.
[RFC2047] Moore, K., "MIME (Multipurpose
Internet Mail Extensions) Part Three:
Message Header Extensions for Non-
ASCII Text", RFC 2047, November 1996.
[RFC3156] Elkins, M., Del Torto, D., Levien, R.,
and T. Roessler, "MIME Security with
OpenPGP", RFC 3156, August 2001.
[RFC5280] Cooper, D., Santesson, S., Farrell,
S., Boeyen, S., Housley, R., and W.
Polk, "Internet X.509 Public Key
Infrastructure Certificate and
Certificate Revocation List (CRL)
Profile", RFC 5280, May 2008.
Abel & Steele Expires June 7, 2011 [Page 14]
Internet-Draft I18N Email Headers December 2010
Authors' Addresses
Abel Yang
TWNIC
4F-2, No. 9, Sec 2, Roosevelt Rd.
Taipei, 100
Taiwan
Phone: +886 2 23411313 ext 505
EMail: abelyang@twnic.net.tw
Shawn Steele
Microsoft
EMail: Shawn.Steele@microsoft.com
Abel & Steele Expires June 7, 2011 [Page 15]