ECRIT R. Gellens
Internet-Draft Core Technology Consulting
Intended status: Standards Track B. Rosen
Expires: April 21, 2017 NeuStar, Inc.
H. Tschofenig
Individual
October 18, 2016
Next-Generation Vehicle-Initiated Emergency Calls
draft-ietf-ecrit-car-crash-18.txt
Abstract
This document describes how to use IP-based emergency services
mechanisms to support the next generation of emergency calls placed
by vehicles (automatically in the event of a crash or serious
incident, or manually invoked by a vehicle occupant) and conveying
vehicle, sensor, and location data related to the crash or incident.
Such calls are often referred to as "Automatic Crash Notification"
(ACN), or "Advanced Automatic Crash Notification" (AACN), even in the
case of manual trigger. The "Advanced" qualifier refers to the
ability to carry a richer set of data.
This document also registers a MIME media type and Emergency Call
Additional Data Block for the vehicle, sensor, and location data
(often referred to as "crash data" even though there is not
necessarily a crash) and an INFO package to enable carrying this and
related data in INFO requests. An external specification for the
data format, contents, and structure are referenced in this document.
This document reuses the technical aspects of next-generation pan-
European eCall (a mandated and standardized system for emergency
calls by in-vehicle systems within Europe and other regions).
However, this document specifies a different set of vehicle (crash)
data, specifically, the Vehicle Emergency Data Set (VEDS) rather than
the eCall Minimum Set of Data (MSD). This document is an extension
of the eCall document, with the primary differences being that this
document makes the MSD data set optional and VEDS mandatory, and adds
attribute values to the metadata/control object to permit greater
functionality. This document registers a new INFO package (identical
to that registered for eCall but with the addition of the VEDS MIME
type). This document also describes legacy (circuit-switched) ACN
systems and their migration to next-generation emergency calling, to
provide background information and context.
Gellens, et al. Expires April 21, 2017 [Page 1]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 21, 2017.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Document Scope . . . . . . . . . . . . . . . . . . . . . . . 7
4. Overview of Legacy Deployment Models . . . . . . . . . . . . 8
5. Migration to Next-Generation . . . . . . . . . . . . . . . . 9
6. Vehicle Data . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Data Transport . . . . . . . . . . . . . . . . . . . . . . . 14
8. Call Setup . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. Call Routing . . . . . . . . . . . . . . . . . . . . . . . . 16
10. New Metadata/Control Values . . . . . . . . . . . . . . . . . 17
10.1. New values for the 'action' attribute' . . . . . . . . . 18
10.2. Request Example . . . . . . . . . . . . . . . . . . . . 19
10.3. The <ack> element . . . . . . . . . . . . . . . . . . . 19
10.4. The <capabilities> element . . . . . . . . . . . . . . . 20
Gellens, et al. Expires April 21, 2017 [Page 2]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
11. Test Calls . . . . . . . . . . . . . . . . . . . . . . . . . 21
12. The emergencyCallData.eCall.VEDS INFO package . . . . . . . . 22
12.1. Overall Description . . . . . . . . . . . . . . . . . . 22
12.2. Applicability . . . . . . . . . . . . . . . . . . . . . 23
12.3. Info Package Name . . . . . . . . . . . . . . . . . . . 23
12.4. Info Package Parameters . . . . . . . . . . . . . . . . 23
12.5. SIP Option-Tags . . . . . . . . . . . . . . . . . . . . 23
12.6. INFO Request Body Parts . . . . . . . . . . . . . . . . 24
12.7. Info Package Usage Restrictions . . . . . . . . . . . . 24
12.8. Rate of INFO Requests . . . . . . . . . . . . . . . . . 24
12.9. Info Package Security Considerations . . . . . . . . . . 25
12.10. Implementation Details . . . . . . . . . . . . . . . . . 25
12.11. Examples . . . . . . . . . . . . . . . . . . . . . . . . 25
13. Example . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
14. Security Considerations . . . . . . . . . . . . . . . . . . . 31
15. Privacy Considerations . . . . . . . . . . . . . . . . . . . 31
16. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 31
16.1. MIME Media Type Registration for
'application/EmergencyCall.VEDS+xml' . . . . . . . . . . 32
16.2. Registration of the 'VEDS' entry in the Emergency Call
Additional Data registry . . . . . . . . . . . . . . . . 33
16.3. New Action Values . . . . . . . . . . . . . . . . . . . 33
16.4. Static Message Registry . . . . . . . . . . . . . . . . 34
16.5. Lamp ID Registry . . . . . . . . . . . . . . . . . . . . 35
16.6. Camera ID Registry . . . . . . . . . . . . . . . . . . . 36
17. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 37
18. Changes from Previous Versions . . . . . . . . . . . . . . . 37
18.1. Changes from draft-ietf-17 to draft-ietf-18 . . . . . . 37
18.2. Changes from draft-ietf-16 to draft-ietf-17 . . . . . . 38
18.3. Changes from draft-ietf-14 to draft-ietf-15 . . . . . . 38
18.4. Changes from draft-ietf-13 to draft-ietf-14 . . . . . . 38
18.5. Changes from draft-ietf-11 to draft-ietf-13 . . . . . . 38
18.6. Changes from draft-ietf-10 to draft-ietf-11 . . . . . . 38
18.7. Changes from draft-ietf-09 to draft-ietf-10 . . . . . . 38
18.8. Changes from draft-ietf-08 to draft-ietf-09 . . . . . . 38
18.9. Changes from draft-ietf-07 to draft-ietf-08 . . . . . . 39
18.10. Changes from draft-ietf-06 to draft-ietf-07 . . . . . . 39
18.11. Changes from draft-ietf-05 to draft-ietf-06 . . . . . . 39
18.12. Changes from draft-ietf-04 to draft-ietf-05 . . . . . . 39
18.13. Changes from draft-ietf-03 to draft-ietf-04 . . . . . . 39
18.14. Changes from draft-ietf-02 to draft-ietf-03 . . . . . . 39
18.15. Changes from draft-ietf-01 to draft-ietf-02 . . . . . . 39
18.16. Changes from draft-ietf-00 to draft-ietf-01 . . . . . . 40
18.17. Changes from draft-gellens-02 to draft-ietf-00 . . . . . 40
18.18. Changes from draft-gellens-01 to -02 . . . . . . . . . . 40
18.19. Changes from draft-gellens-00 to -01 . . . . . . . . . . 40
19. References . . . . . . . . . . . . . . . . . . . . . . . . . 40
19.1. Normative References . . . . . . . . . . . . . . . . . . 40
Gellens, et al. Expires April 21, 2017 [Page 3]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
19.2. Informative references . . . . . . . . . . . . . . . . . 42
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 42
1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
This document re-uses terminology defined in Section 3 of [RFC5012].
Additionally, we use the following abbreviations:
+--------+----------------------------------------------------------+
| Term | Expansion |
+--------+----------------------------------------------------------+
| 3GPP | 3rd Generation Partnership Project |
| AACN | Advanced Automatic Crash Notification |
| ACN | Automatic Crash Notification |
| APCO | Association of Public-Safety Communications Officials |
| EENA | European Emergency Number Association |
| ESInet | Emergency Services IP network |
| GNSS | Global Navigation Satellite System (which includes |
| | various systems such as the Global Positioning System or |
| | GPS) |
| IVS | In-Vehicle System |
| MNO | Mobile Network Operator |
| MSD | eCall Minimum Set of Data |
| NENA | National Emergency Number Association |
| POTS | Plain Old Telephone Service (normal, circuit-switched |
| | voice calls) |
| PSAP | Public Safety Answering Point |
| TSP | Telematics Service Provider |
| VEDS | Vehicle Emergency Data Set |
+--------+----------------------------------------------------------+
Because the endpoints of an NG-ACN call are a PSAP and an IVS or TSP,
to avoid receptively writing "IVS or TSP", the term "IVS" is used to
represent either an IVS or TSP when discussing signaling behavior
(e.g., attaching VEDS data, sending an INVITE request, receiving an
INFO request, etc.).
2. Introduction
Emergency calls made by in-vehicle systems (e.g., automatically in
the event of a crash or serious incident or manually by a vehicle
occupant) assist in significantly reducing road deaths and injuries
by allowing emergency services to respond quickly and appropriately
Gellens, et al. Expires April 21, 2017 [Page 4]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
to the specifics of the incident, often with better location
accuracy.
Drivers often have a poor location awareness, especially outside of
major cities, at night and when away from home (especially abroad).
In the most crucial cases, the victim(s) might not be able to call
because they have been injured or trapped.
For more than two decades, some vehicles have been equipped with
telematics systems which, among other features, place an emergency
call automatically in the event of a crash or manually in response to
an emergency call button. Such systems generally have on-board
location determination systems that make use of satellite-based
positioning technology, inertial sensors, gyroscopes, etc., which can
provide an accurate position for the vehicle. Such built-in systems
can take advantage of the benefits of being integrated into a
vehicle, such as more power capacity, ability to have larger or
specialized antenna, ability to be engineered to avoid or minimise
degradation by vehicle glass coatings, interference from other
vehicle systems, etc. Thus, the PSAP can be provided with a good
estimate of where the vehicle is during an emergency. Vehicle
manufacturers are increasingly adopting such systems, both for the
safety benefits and for the additional features and services they
enable (e.g., remote engine diagnostics, remote door unlock, stolen
vehicle tracking and disabling, etc.).
The general term for such systems is Automatic Crash Notification
(ACN) or "Advanced Automatic Crash Notification" (AACN). "ACN" is
used in this document as a general term. ACN systems transmit some
amount of data specific to the incident, referred to generally as
"crash data" (the term is commonly used even though there might not
have been a crash). While different systems transmit different
amounts of crash data, standardized formats, structures, and
mechanisms are needed to provide interoperability among systems and
PSAPs.
As of the date of this document, currently deployed in-vehicle
telematics systems are circuit-switched and lack a standards-based
ability to convey crash data directly to the PSAP (generally relying
on either a human advisor or an automated text-to-speech system to
provide the PSAP call taker with some crash data orally, or in some
cases via a proprietary mechanism). In most cases, the PSAP call
taker needs to first realize that the call is related to a vehicle
incident, and then listen to the data and transcribe it. Circuit-
switched ACN systems are referred to here as CS-ACN.
The transition to next-generation calling in general, and for
emergency calling in particular, provides an opportunity to vastly
Gellens, et al. Expires April 21, 2017 [Page 5]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
improve the scope, breadth, reliability and usefulness of crash data
during an emergency by allowing it to be transmitted during call set-
up, and to be automatically processed by the PSAP and made available
to the call taker in an integrated, automated way, as well as provide
the ability for a PSAP call taker to request that a vehicle take
certain actions, such as flashing lights or unlocking doors. In
addition, vehicle manufacturers are provided an opportunity to take
advantage of the same standardized mechanisms for data transmission
and request processing for internal use if they wish (such as
telemetry between the vehicle and a service center for both emergency
and non-emergency uses, including location-based services, multi-
media entertainment systems, remote door unlocking, and road-side
assistance applications).
Next-generation ACN provides an opportunity for such calls to be
recognized and processed as such during call set-up, and routed to an
equipped PSAP where the vehicle data is available to assist the call
taker in assessing and responding to the situation. Next-generation
(IP-based) ACN systems are referred to here as NG-ACN.
An ACN call can be initiated by a vehicle occupant or automatically
initiated by vehicle systems in the event of a serious incident.
(The "A" in "ACN" does stand for "Automatic," but the term is broadly
used to refer to the class of calls that are placed by an in-vehicle
system (IVS) or Telematics Service Providers (TSP) and that carry
incident-related data as well as voice.) Automatically triggered
calls indicate a car crash or some other serious incident (e.g., a
fire). Manually triggered calls are often reports of observed
crashes or serious hazards (such as impaired drivers or roadway
debris). In some implementations, manually triggered calls might be
more likely to be accidental.
The Association of Public-Safety Communications Officials (APCO) and
the National Emergency Number Association (NENA) have jointly
developed a standardized set of incident-related vehicle data for ACN
use, called the Vehicle Emergency Data Set (VEDS) [VEDS]. Such data
is often referred to as crash data although it is applicable in
incidents other than crashes.
This document describes how the IETF mechanisms for IP-based
emergency calls are used to provide the realization of next-
generation ACN.
This document reuses the technical aspects of next-generation pan-
European eCall (a mandated and standardized system for emergency
calls by in-vehicle systems within Europe), as described in
[I-D.ietf-ecrit-ecall]. However, this document specifies a different
set of vehicle (crash) data, specifically, the Vehicle Emergency Data
Gellens, et al. Expires April 21, 2017 [Page 6]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
Set (VEDS) rather than the eCall Minimum Set of Data (MSD). This
document is an extension of [I-D.ietf-ecrit-ecall], with the
differences being that this document makes the MSD data set optional
and VEDS mandatory, and adds new attribute values to the metadata/
control object defined in that document. This document also
registers a new INFO package (identical to that defined in
[I-D.ietf-ecrit-ecall] with the addition of the VEDS MIME type).
This document registers the 'application/EmergencyCallData.VEDS+xml'
MIME media type, registers the 'VEDS' entry in the Emergency Call
Additional Data registry, and registers an INFO package to enable
carrying this and related data in INFO requests.
Section 6 introduces VEDS. Section 7 describes how VEDS data and
metadata/control blocks are transported within NG-ACN calls.
Section 8 describes how such calls are placed.
These mechanisms are used to place emergency calls that are
identifiable as ACN calls and that carry standardized crash data in
an interoperable way.
Calls by in-vehicle systems are placed using cellular networks, which
might ignore location information sent by an originating device in an
emergency call INVITE, instead attaching their own location
information (often determined in cooperation with the originating
device). Standardized crash data structures often include location
as determined by the IVS. A benefit of this is that it allows the
PSAP to see both the location as determined by the cellular network
(often in cooperation with the originating device) and the location
as determined by the IVS.
This specification inherits the ability to utilize test call
functionality from Section 15 of [RFC6881].
3. Document Scope
This document is focused on how an ACN emergency call is setup and
incident-related data (including vehicle, sensor, and location data)
is transmitted to the PSAP using IETF specifications. For the direct
model, this is the end-to-end description (between the vehicle and
the PSAP). For the TSP model, this describes the call leg between
the TSP and the PSAP, leaving the call leg between the vehicle and
the TSP up to the entities involved (i.e., IVS and TSP vendors) who
are then free to use the same mechanism as for the right-hand side or
not.
Note that Europe has a mandated and standardized system for emergency
calls by in-vehicle systems. This pan-European system is known as
Gellens, et al. Expires April 21, 2017 [Page 7]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
"eCall" and is the subject of a separate document,
[I-D.ietf-ecrit-ecall], which this document builds on. Vehicles
designed to operate in multiple regions might need to support eCall
as well as NG-ACN as described here. A vehicle IVS might determine
whether to use eCall or ACN by first determining the region or
country in which it is located (e.g., from a GNSS location estimate
and/or identity of or information from an MNO). If other regions
adopt other data formats, a multi-region vehicle might need to
support those as well. This document adopts the call set-up and
other technical aspects of [I-D.ietf-ecrit-ecall], which uses
[RFC7852]; this makes it straightforward to use a different data set
while keeping other technical aspects unchanged. Hence, both NG-
eCall and the NG-ACN mechanism described here are compatible,
differing primarily in the specific data block that is sent (the
eCall MSD in the case of NG-eCall, and the APCO/NENA VEDS used in
this document), and some additions to the metadata/control data
block. If other regions adopt their own vehicle data sets, this can
be similarly accomodated without changing other technical aspects.
Note that any additional data formats require a new INFO package to
permit transport within INFO requests.
4. Overview of Legacy Deployment Models
Legacy (circuit-switched) systems for placing emergency calls by in-
vehicle systems generally have some ability to convey at least
location and in some cases telematics data to the PSAP. Most such
systems use one of three architectural models, which are described
here as: "Telematics Service Provider" (TSP), "direct", and "paired".
These three models are illustrated below.
In the TSP model, both emergency and non-emergency calls are placed
to a Telematics Service Provider (TSP); a proprietary technique is
used for data transfer (such as a proprietary in-band modem) between
the TSP and the vehicle.
In an emergency, generally the TSP call taker bridges in the PSAP and
communicates location, crash data (such as impact severity and trauma
prediction), and other data (such as the vehicle description) to the
PSAP call taker verbally (in some cases, a proprietary out-of-band
interface is used). Since the TSP knows the location of the vehicle
(from on-board GNSS and sensors), location-based routing is usually
used to route to the appropriate PSAP. In some cases, the TSP is
able to transmit location automatically, using similar techniques as
for wireless calls. Typically, a three-way voice call is established
between the vehicle, the TSP, and the PSAP, allowing communication
between the PSAP call taker, the TSP call taker, and the vehicle
occupants (who might be unconscious).
Gellens, et al. Expires April 21, 2017 [Page 8]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
///----\\\ proprietary +------+ 911 trunk or POTS +------+
||| IVS |||-------------->+ TSP +------------------->+ PSAP |
\\\----/// crash data +------+ location via trunk +------+
Figure 1: Legacy TSP Model.
In the paired model, the IVS uses a Bluetooth link with a previously-
paired handset to establish an emergency call with the PSAP (by
dialing a standard emergency number; 9-1-1 in North America), and
then communicates location data to the PSAP via text-to-speech; crash
data might or might not be conveyed also using text-to-speech. Some
such systems use an automated voice prompt menu for the PSAP call
taker (e.g., "this is an automatic emergency call from a vehicle;
press 1 to open a voice path to the vehicle; press 2 to hear the
location read out") to allow the call taker to request location data
via text-to-speech.
+---+
///----\\\ | H | 911/etc voice call via handset +------+
||| IVS |||-->| S +----------------------------------->+ PSAP |
\\\----/// +---+ location via text-to-speech +------+
Figure 2: Legacy Paired Model
In the direct model, the IVS directly places an emergency call with
the PSAP by dialing a standard emergency number (9-1-1 in North
America). Such systems might communicate location data to the PSAP
via text-to-speech; crash data might or might not be conveyed using
text-to-speech. Some such systems use an automated voice prompt menu
(e.g., "this is an automatic emergency call from a vehicle; press 1
to open a voice path to the vehicle; press 2 to hear the location
read out") to allow the call taker to request location data via text-
to-speech.
///----\\\ 911/etc voice call via IVS +------+
||| IVS |||---------------------------------------->+ PSAP |
\\\----/// location via text-to-speech +------+
Figure 3: Legacy Direct Model
5. Migration to Next-Generation
Migration of emergency calls placed by in-vehicle systems to next-
generation (all-IP) technology per this document provides a
standardized mechanism to identify such calls and to present crash
Gellens, et al. Expires April 21, 2017 [Page 9]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
data with the call, as well as enabling additional communications
modalities and enhanced functionality. This allows ACN calls and
crash data to be automatically processed by the PSAP and made
available to the call taker in an integrated, automated way. Because
the crash data is carried in the initial SIP INVITE (per [RFC7852])
the PSAP can present it to the call taker simultaneously with the
appearance of the call. The PSAP can also process the data to take
other actions (e.g., if multiple calls from the same location arrive
when the PSAP is busy and a subset of them are NG-ACN calls, a PSAP
might choose to store the information and reject the calls, since the
IVS will receive confirmation that the information has been
successfully received; a PSAP could also choose to include a message
stating that it is aware of the incident and responders are on the
way; a PSAP could call the vehicle back when a call taker is
available).
Origination devices and networks, PSAPs, emergency services networks,
and other telephony environments are migrating to next-generation.
This provides opportunities for significant enhancement to
interoperability and functionality, especially for emergency calls
carrying additional data such as vehicle crash data. (In the U.S., a
network specifically for emergency responders is being developed.
This network, FirstNet, will be next-generation from the start,
enhancing the ability for data exchange between PSAPs and
responders.)
Migration to next-generation (NG) provides an opportunity to
significantly improve the handling and response to vehicle-initiated
emergency calls. Such calls can be recognized as originating from a
vehicle, routed to a PSAP equipped both technically and operationally
to handle such calls, and the vehicle-determined location and crash
data can be made available to the call taker simultaneously with the
call appearance. The PSAP can take advantage of enhanced
functionality, including the ability to request the vehicle to take
an action, such as sending an updated set of data, converying a
message to the occupants, flashing lights, unlocking doors, etc.
Vehicle manufacturers using the TSP model can choose to take
advantage of the same mechanism to carry telematics data and requests
and responses between the vehicle and the TSP for both emergency and
non-emergency calls as are used for the interface with the PSAP.
A next-generation IVS establishes an emergency call using the
emergency call solution as described in [RFC6443] and [RFC6881], with
the difference that the Request-URI indicates an ACN type of
emergency call, the IVS typically does not perform routing or
location queries but relies on the carrier for this, and uses Call-
Info header fields to indicates that vehicle crash and capabilities
Gellens, et al. Expires April 21, 2017 [Page 10]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
data is attached. When an ESInet is deployed, the MNO only needs to
recognize the call as an emergency call and route it to an ESInet.
The ESInet can recognize the call as an ACN with vehicle data and can
route the call to an NG-ACN capable PSAP. Such a PSAP can interpret
the vehicle data sent with the call and make it available to the call
taker.
[I-D.ietf-ecrit-ecall] registers new service URN children within the
"sos" subservice. These URNs request NG-ACN resources, and
differentiate between manually and automatically triggered NG-ACN
calls (which might be subject to different treatment depending on
policy). The two service URNs registered in [I-D.ietf-ecrit-ecall]
are "urn:service:sos.ecall.automatic" and
"urn:service:sos.ecall.manual". The same service URNs are used for
ACN as for eCall since in any region only one of these is supported,
making a distinction unnecessary. (Further, PSAP equipment might
support multiple data formats, allowing a PSAP to handle a vehicle
that erroneously sent the wrong data object.)
Note that in North America, routing queries performed by clients
outside of an ESInet typically treat all sub-services of "sos"
identically to "sos" with no sub-service. However, the Request-URI
header field retains the full sub-service; route and handling
decisions within an ESInet or PSAP can take the sub-service into
account. For example, in a region with multiple cooperating PSAPs,
an NG-ACN call might be routed to a PSAP that is NG-ACN capable, or
one that specializes in vehicle-related incidents.
Migration of the three architectural models to next-generation (all-
IP) is described below.
In the TSP model, the IVS transmits crash and location data to the
TSP either by re-using the mechanisms and data objects described
here, or using a proprietary mechanism. In an emergency, the TSP
bridges in the PSAP and the TSP transmits crash and other data to the
PSAP using the mechanisms and data objects described here. There is
a three-way call between the vehicle, the TSP, and the PSAP, allowing
communication between the PSAP call taker, the TSP call taker, and
the vehicle occupants (who might be unconscious). The TSP relays
PSAP requests and vehicle responses.
proprietary
///----\\\ or standard +------+ standard +------+
||| IVS ||| ------------------->+ TSP +------------------->+ PSAP |
\\\----/// crash + other data +------+ crash + other data +------+
Figure 4: Next-Generation TSP Model
Gellens, et al. Expires April 21, 2017 [Page 11]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
The vehicle manufacturer and the TSP can choose to use the same
mechanisms and data objects on the left call leg in Figure 4 as on
the right. (Note that the TSP model can be more difficult when the
vehicle is in a different country than the TSP (e.g., a US resident
driving in Canada or Mexico) because of the additional complexity in
choosing the correct PSAP based on vehicle location performed by a
TSP in a different country.)
In the direct model, the IVS communicates crash data to the PSAP
directly using the mechanisms and data objects described here.
///----\\\ NG emergency call +------+
||| IVS |||----------------------------------------->+ PSAP |
\\\----/// crash + other data +------+
Figure 5: Next-Generation Direct Model
In the paired model, the IVS uses a Bluetooth link to a previously-
paired handset to establish an emergency call with the PSAP; it is
undefined what facilities are or will be available for transmitting
crash data through the Bluetooth link to the handset for inclusion in
an NG emergency call. Hence, manufacturers that use the paired model
for legacy calls might choose to adopt either the direct or TSP
models for next-generation calls.
+---+
///----\\\ (undefined) | H | standard +------+
||| IVS |||------------------>| S +------------------->+ PSAP |
\\\----/// (undefined) +---+ crash + other data +------+
Figure 6: Next-Generation Paired Model
If the call is routed to a PSAP that is not capable of processing the
vehicle data, the PSAP ignores (or does not receive) the vehicle
data. This is detectable by the IVS or TSP when the status response
to the INVITE (e.., 200 OK) lacks a control structure acknowledging
receipt of the data [I-D.ietf-ecrit-ecall]. The IVS or TSP then
proceeds as it would for a CS-ACN call (e.g., verbal conveyance of
data)
6. Vehicle Data
The Association of Public-Safety Communications Officials (APCO) and
the National Emergency Number Association (NENA) have jointly
developed a standardized set of incident-related vehicle data for ACN
use, called the Vehicle Emergency Data Set (VEDS) [VEDS]. Such data
is often referred to as crash data although it is applicable in
incidents other than crashes.
Gellens, et al. Expires April 21, 2017 [Page 12]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
VEDS provides a standard data set for the transmission, exchange, and
interpretation of vehicle-related data. A standard data format
allows the data to be generated by an IVS or TSP and interpreted by
PSAPs, emergency responders, and medical facilities. It includes
incident-related information such as airbag deployment, location and
compass orientation of the vehicle, spatial orientation of the
vehicle (e.g., upright, on its side or roof or a bumper), various
sensor data that can indicate the potential severity of the crash and
the likelihood of severe injuries to the vehicle occupants, etc.
This data better informs the PSAP and emergency responders as to the
type of response that might be needed. Some of this information has
been included in U.S. government guidelines for field triage of
injured patients [triage-2008] [triage-2011]. These guidelines are
designed to help responders identify the potential existence of
severe internal injuries and to make critical decisions about how and
where a patient needs to be transported.
VEDS is an XML structure (see [VEDS]) transported in SIP using the
'application/EmergencyCallData.VEDS+xml' MIME media type.
If new data blocks are needed (e.g., in other regions or for enhanced
data), the steps required during standardization are briefly
summarized below:
o A set of data is standardized by an SDO or appropriate
organization
o A MIME media type for the crash data set is registered with IANA
* If the data is specifically for use in emergency calling, the
MIME media type is normally under the 'application' type with a
subtype starting with 'EmergencyCallData.'
* If the data format is XML, then by convention the name has a
suffix of '+xml'
o The item is registered in the Emergency Call Additional Data
registry, as defined in Section 9.1.7 of [RFC7852]
* For emergency-call-specific formats, the registered name is the
root of the MIME media type (not including the
'EmergencyCallData' prefix and any suffix such as '+xml') as
described in Section 4.1 of [RFC7852].
o A new INFO package is registered that permits carrying the the new
media type, the metadata/control object (defined in
[I-D.ietf-ecrit-ecall]), and for compatibility, the MSD and VEDS
objects, in INFO messages.
Gellens, et al. Expires April 21, 2017 [Page 13]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
7. Data Transport
[RFC7852] establishes a general mechanism for attaching blocks of
data to a SIP emergency call. This mechanism permits certain
emergency call MIME types to be attached to SIP messages. This
document makes use of that mechanism. This document also registers
an INFO package (in Section 12) to enable NG-ACN related data blocks
to be carried in SIP INFO requests (per [RFC6086], new INFO usages
require the definition of an INFO package).
An In-Vehicle System (IVS) transmits a VEDS data block (see [VEDS])
by attaching it to a SIP message as a MIME body part per [RFC7852].
The body part is identified by its MIME media type ('application/
emergencyCallData.VEDS+xml') in the Content-Type header field of the
body part. The body part is assigned a unique identifier which is
listed in a Content-ID header field in the body part. The SIP
message is marked as containing the VEDS data by adding (or appending
to) a Call-Info header field at the top level of the SIP message.
This Call-Info header field contains a CID URL referencing the body
part's unique identifier, and a 'purpose' parameter identifying the
data as a VEDS data block per the Emergency Call Additional Data
Blocks registry entry; the 'purpose' parameter's value is
'emergencyCallData.VEDS'. A VEDS data block is carried in a SIP INFO
request by using the INFO package defined in Section 12.
A PSAP or IVS transmits a metadata/control object (see
[I-D.ietf-ecrit-ecall]) by attaching it to a SIP message as a MIME
body part per [RFC7852]. The body part is identified by its MIME
media type ('application/emergencyCallData.control+xml') in the
Content-Type header field of the body part. The body part is
assigned a unique identifier which is listed in a Content-ID header
field in the body part. The SIP message is marked as containing the
metadata/control block by adding (or appending to) a Call-Info header
field at the top level of the SIP message. This Call-Info header
field contains a CID URL referencing the body part's unique
identifier, and a 'purpose' parameter identifying the data as a
metadata/control block per the Emergency Call Additional Data Blocks
registry entry; the 'purpose' parameter's value is
'emergencyCallData.control'. A metadata/control object is carried in
a SIP INFO request by using the INFO package defined in Section 12.
A body part containing a VEDS or metadata/control object has a
Content-Disposition header field value containing "By-Reference" and
is always enclosed in a multipart body part (even if it would
otherwise be the only body part in the SIP message), since as of the
date of this document, the use of Content-ID as a SIP header field is
not defined (while it is defined for use as a MIME header field).
Gellens, et al. Expires April 21, 2017 [Page 14]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
An In-Vehicle System (IVS) initiating an NG-ACN call includes in the
initial INVITE a VEDS data block and a metadata/control object
informing the PSAP of its capabilities. The VEDS and metadata/
control body parts (and PIDF-LO) have a Content-Disposition header
field with the value "By-Reference; handling=optional". Specifying
handling=optional prevents the INVITE from being rejected if it is
processed by a legacy element (e.g., a gateway between SIP and
circuit-switched environments) that does not understand the VEDS or
metadata/control (or PIDF-LO) objects. The PSAP creates a metadata/
control object acknowledging receipt of the VEDS data and includes it
in the SIP final response to the INVITE. The metadata/control object
is not attached to provisional (e.g., 180) responses.
If the IVS receives an acknowledgment for a VEDS data object with
received=false, this indicates that the PSAP was unable to properly
decode or process the VEDS. The IVS action is not defined (e.g., it
might only log an error). Since the PSAP is able to request an
updated VEDS during the call, if an initial VEDS is unsatisfactory in
any way, the PSAP can choose to request another one.
A PSAP can request that the vehicle send an updated VEDS data block
during a call. To do so, the PSAP creates a metadata/control object
requesting VEDS data and attaches it to a SIP INFO request and sends
it within the dialog. The IVS then attaches an updated VEDS data
object to a SIP INFO request and sends it within the dialog. If the
IVS is unable to send the VEDS, it instead sends a metadata/control
object acknowledging the request with the 'success' parameter set to
'false' and a 'reason' parameter (and optionally a 'details'
parameter) indicating why the request cannot be accomplished. Per
[RFC6086], metadata/control objects and VEDS data are sent using the
INFO package defined in Section 12. In addition, to align with the
way a VEDS or metadata/control block is transmitted in a SIP message
other than an INFO request, one or more Call-Info header fields are
included in the SIP INFO request to reference the VEDS or metadata/
control block. See Section 12 for more information on the use of
INFO requests within NG-ACN calls.
Any metadata/control object sent by a PSAP can request that the
vehicle perform an action (such as sending a data block, flashing
lights, providing a camera feed, etc.) The vehicle sends an
acknowledgement for any request other than a successfully executed
send-data action. Multiple requests with the same 'action' value
MUST be sent in separate body parts (to avoid any ambiguity in the
acknowledgement).
If the IVS is aware that VEDS data it sent previously has changed, it
MAY send an unsolicited VEDS in any convenient SIP message, including
an INFO request during the call. The PSAP sends an acknowledgment
Gellens, et al. Expires April 21, 2017 [Page 15]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
for an unsolicited VEDS object (if the IVS sent the unsolicited VEDS
in an INFO request, the acknowledgment is sent in a new INFO request,
otherwise it is sent in the response to the message containing the
VEDS).
8. Call Setup
A next-generation In-Vehicle System (IVS) initiates an NG-ACN call
with a SIP INVITE using one of the SOS sub-services
"SOS.ecall.automatic" or "SOS.ecall.manual" in the Request-URI,
standard sets of crash data and capabilities data encoded in
standardized and registered formats, attached as additional data
blocks as specified in Section 4.1 of [RFC7852]. As described in
that document, each data block is identified by its MIME media type,
and pointed to by a CID URL in a Call-Info header with a 'purpose'
parameter value corresponding to the data block.
When placing an emergency call, the crash data set and IVS capability
data are transported as described in Section 7.
The Vehicle Emergency Data Set (VEDS) is an XML structure defined by
the Association of Public-Safety Communications Officials (APCO) and
the National Emergency Number Association (NENA) [VEDS]. It is
carried in a body part with MIME media type 'application/
EmergencyCallData.VEDS+xml'.
Entities along the path between the vehicle and the PSAP are able to
identify the call as an ACN call and handle it appropriately. The
PSAP is able to identify the crash and capabilities data attached to
the INVITE by examining the Call-Info header fields for 'purpose'
parameters whose values start with 'EmergencyCallData.' The PSAP is
able to access the data it is capable of handling and is interested
in by checking the 'purpose' parameter values.
This document extends [I-D.ietf-ecrit-ecall] by reusing the call set-
up and other normative requirements with the exception that in this
document, support for the eCall MSD is OPTIONAL and support for VEDS
in REQUIRED. This document also adds new attribute values to the
metadata/control object defined in [I-D.ietf-ecrit-ecall].
9. Call Routing
An Emergency Services IP Network (ESInet) is a network operated by or
on behalf of emergency services authorities. It handles emergency
call routing and processing before delivery to a PSAP. In the
NG9-1-1 architecture adopted by NENA as well as the NG1-1-2
architecture adopted by EENA, each PSAP is connected to one or more
ESInets. Each originating network is also connected to one or more
Gellens, et al. Expires April 21, 2017 [Page 16]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
ESInets. The ESInets maintain policy-based routing rules that
control the routing and processing of emergency calls. The
centralization of such rules within ESInets allows for a cleaner
separation between the responsibilities of the originating network
and that of the emergency services network, and provides greater
flexibility and control over processing of emergency calls by the
emergency services authorities and PSAPs. This can make it easier to
react quickly to situations that require changes in how emergency
calls are routed or handled (e.g., a natural disaster closes a PSAP),
as well as ease in making long-term changes that affect such routing
(e.g., cooperative agreements to specially handle calls requiring
translation or relay services).
In an environment that uses ESInets, the originating network might
pass all types of emergency calls to an ESInet (all calls with a
service URN of or starting with "sos"). The ESInet then routs such
calls to an appropriate PSAP. In an environment without an ESInet,
the emergency services authorities and the originating carriers
determine how such calls are routed.
10. New Metadata/Control Values
This document adds new attribute values to the metadata/control
structure defined in [I-D.ietf-ecrit-ecall].
In addition to the base usage from the PSAP to the IVS to
acknowledge receipt of crash data, the <ack> element is also
contained in a metadata/control block sent by the IVS to the PSAP.
This is used by the IVS to acknowledge receipt of a request by the
PSAP and indicate if the request was carried out when that request
would not otherwise be acknowledged (if the PSAP requests the
vehicle to send data and the vehicle does so, the data serves as a
success acknowledgement).
The <capabilities> element is used in a metadata/control block
sent from the IVS to the PSAP (e.g., in the initial INVITE) to
inform the PSAP of the vehicle capabilities. Child elements
contain all actions and data types supported by the vehicle and
all available lamps (lights) and cameras.
New request values are added to the <request> element to enable
the PSAP to request the vehicle to perform actions.
Mandatory Actions (the IVS and the PSAP MUST support):
o Transmit data object (VEDS MUST be supported; MSD MAY be
supported)
Optional Actions (the IVS and the PSAP MAY support):
Gellens, et al. Expires April 21, 2017 [Page 17]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
o Play and/or display static (pre-defined) message
o Speak/display dynamic text (text supplied in action)
o Flash or turn on or off a lamp (light)
o Honk horn
o Enable a camera
The <ack> element indicates the object being acknowledged (i.e., a
data object or a metadata/control block containing <request>
elements), and reports success or failure.
The <capabilities> element has child <request> elements indicating
the actions supported by the IVS.
The <request> element contains attributes to indicate the request and
to supply any needed information, and MAY contain a <text> child
element to contain the text for a dynamic message. The 'action'
attribute is mandatory and indicates the specific action.
[I-D.ietf-ecrit-ecall] established an IANA registry to contain the
allowed values; this document adds new values to that registry in
Table 2.
Per [I-D.ietf-ecrit-ecall], the PSAP sends a control/metadata block
in response to the VEDS data sent by the IVS in SIP requests other
than INFO (e.g., the INVITE). This metadata/control block is sent in
the SIP response to the request (e.g., the INVITE response). When
the PSAP needs to send a control block that is not an immediate
response to a VEDS or other data sent by the IVS, the control block
is transmitted from the PSAP to the IVS in a SIP INFO request within
the established dialog. The IVS sends the requested data (e.g., the
VEDS) or an acknowledgment (for requests other than to send data) in
a new INFO request. This mechanism flexibly allows the PSAP to send
metadata/control data to the IVS and the IVS to respond. If control
data sent in a response message requests the IVS to send a new VEDS
or other data block, or to perform an action other than sending data,
the IVS sends the requested data or an acknowledgment regarding the
action in an INFO message within the dialog.
10.1. New values for the 'action' attribute'
The following new "action" values are defined:
msg-static displays or plays a predefined message (translated as
appropriate for the language of the vehicle's interface). A
registry is created in Section 16.4 for messages and their IDs.
Vehicles include the highest registered message in their
<capabilities> element to indicate support for all messages up to
and including the indicated value.
Gellens, et al. Expires April 21, 2017 [Page 18]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
msg-dynamic displays or speaks (via text-to-speech) a dynamic
message included in the request.
honk sounds the horn.
lamp turns a lamp (light) on, off, or flashes.
enable-camera adds a one-way media stream (established via SIP re-
INVITE sent by the vehicle) to enable the PSAP call taker to view
a feed from a camera.
Note that there is no 'request' action to play dynamic media (such as
an audio message). The PSAP can send a SIP re-INVITE to establish a
one-way media stream for this purpose.
10.2. Request Example
<?xml version="1.0" encoding="UTF-8"?>
<EmergencyCallData.control
xmlns="urn:ietf:params:xml:ns:EmergencyCallData:control"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<request action="send-data" datatype="VEDS"/>
<request action="lamp" lamp-id="hazard"
lamp-action="flash" persistance="PT1H"/>
<request action="msg-static" msgid="1"/>
<request action="msg-dynamic">
<text>Remain calm. Help is on the way.</text>
</request>
</EmergencyCallData.control>
Figure 7: Request Example
10.3. The <ack> element
In [I-D.ietf-ecrit-ecall], the <ack> element is transmitted by the
PSAP to acknowledge the MSD. Here, the <ack> element is also
transmitted by the PSAP to acknowledge the VEDS data and by the IVS
to acknowledge receipt of a <request> element that requested the IVS
to perform an action other than transmitting a data object (e.g., a
request to display a message would be acknowledged, but a request to
transmit VEDS data would not result in a separate <ack> element being
sent, since the data object itself serves as acknowledgment.) An
<ack> element sent by an IVS references the unique ID of the
metadata/control object containing the request(s) and indicates
Gellens, et al. Expires April 21, 2017 [Page 19]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
whether the request was successfully performed, and if not,
optionally includes an explanation.
10.3.1. Ack Examples
<?xml version="1.0" encoding="UTF-8"?>
<EmergencyCallData.control
xmlns="urn:ietf:params:xml:ns:EmergencyCallData:control"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<ack ref="1234567890@atlanta.example.com">
<actionResult action="msg-dynamic" success="true"/>
<actionResult action="lamp" success="false" reason="unable"
details="The requested lamp is inoperable"/>
</ack>
</EmergencyCallData.control>
Figure 8: Ack Example from IVS to PSAP
10.4. The <capabilities> element
The <capabilities> element ([I-D.ietf-ecrit-ecall]) is transmitted by
the IVS to indicate its capabilities to the PSAP.
The <capabilities> element contains a <request> child element per
action supported by the vehicle. The vehicle MUST support sending
the VEDS data object and so includes at a minimum a <request> child
element with the 'action' attribute set to "send-data" and the
'supported-values' attribute containing all data blocks supported by
the IV, which MUST include 'VEDS'. All other actions are OPTIONAL.
If the "msg-static" action is supported, a <request> child element
with the 'action' attribute set to "msg-static" is included, with the
'msgid' attribute set to the highest supported static message
supported by the vehicle. A registry is created in Section 16.4 to
map 'msgid' values to static text messages. By sending the highest
supported static message number in its <capabilities> element, the
vehicle indicates its support for all static messages in the registry
up to and including that value.
If the "lamp" action is supported, a <request> child element with the
'action' attribute set to "lamp" is included, with the 'supported-
values' attribute set to all supported lamp IDs. A registry is
created in Section 16.5 to contain lamp ID values.
Gellens, et al. Expires April 21, 2017 [Page 20]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
If the "enable-camera" action is supported, a <request> child element
with the 'action' attribute set to "enable-camera" is included, with
the 'supported-values' attribute set to all supported camera IDs. A
registry is created in Section 16.6 to contain camera ID values.
10.4.1. Capabilities Example
<?xml version="1.0" encoding="UTF-8"?>
<EmergencyCallData.control
xmlns="urn:ietf:params:xml:ns:EmergencyCallData:control"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<capabilities>
<request action="send-data" supported-values="VEDS"/>
<request action="lamp"
supported-values="head;interior;fog-front;fog-rear;brake;
position-front;position-rear;turn-left;turn-right;hazard"/>
<request action="msg-static" msgid="3"/>
<request action="msg-dynamic"/>
<request action="honk"/>
<request action="enable-camera" supported-values="backup; interior"/>
</capabilities>
</EmergencyCallData.control>
Figure 9: Capabilities Example
11. Test Calls
An NG-ACN test call is a call that is recognized and treated to some
extent as an NG-ACN call but not given emergency call treatment and
not handled by a call taker. The specific handling of test NG-ACN
calls is not itself standardized; the test call facility is intended
to allow the IVS, user, or TSP to verify that an NG-ACN call can be
successfully established with voice and/or other media communication.
The IVS might also be able to verify that the crash data was
successfully received.
This document builds on [I-D.ietf-ecrit-ecall], which inherits the
ability to utilize test call functionality from Section 15 of
[RFC6881]. A service URN starting with "test." indicates a test
call. [I-D.ietf-ecrit-ecall] registered "urn:service:test.sos.ecall"
for test calls.
MNOs, emergency authorities, ESInets, and PSAPs determine how to
treat a vehicle call requesting the "test" service URN so that the
Gellens, et al. Expires April 21, 2017 [Page 21]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
desired functionality is tested, but this is outside the scope of
this document. (One possibility is that MNOs route such calls as
non-emergency calls to an ESInet, which routes them to a PSAP that
supports NG-ACN calls; the PSAP accepts test calls, sends a crash
data acknowledgment, and plays an audio clip (for example, saying
that the call reached an appropriate PSAP and the vehicle data was
successfully processed) in addition to supporting media loopback per
[RFC6881]).
Note that since test calls are placed using "test" as the parent
service URN and "sos" as a child, such calls are not treated as an
emergency call and so some functionality might not apply (such as
preemption or service availability for devices lacking service ("non-
service-initialized" or "NSI" devices) if those are available for
emergency calls).
12. The emergencyCallData.eCall.VEDS INFO package
This document registers the 'emergencyCallData.eCall.VEDS' INFO
package.
Both endpoints (the IVS and the PSAP equipment) include
'emergencyCallData.eCall.VEDS' in a Recv-Info header field per
[RFC6086] to indicate ability to receive INFO messages carrying data
as described here.
Support for the 'emergencyCallData.eCall.VEDS' INFO package indicates
the ability to receive NG-ACN related body parts as specified in
[TBD: THIS DOCUMENT].
An INFO request message carrying data related to an emergency call as
described in [TBD: THIS DOCUMENT] has an Info-Package header field
set to 'emergencyCallData.eCall.VEDS' per [RFC6086].
The requirements of Section 10 of [RFC6086] are addressed in the
following sections.
12.1. Overall Description
This section describes "what type of information is carried in INFO
requests associated with the Info Package, and for what types of
applications and functionalities UAs can use the Info Package."
INFO requests associated with the emergencyCallData.eCall.VEDS INFO
package carry data associated with emergency calls as defined in
[TBD: THIS DOCUMENT]. The application is vehicle-initiated emergency
calls established using SIP. The functionality is to carry vehicle
Gellens, et al. Expires April 21, 2017 [Page 22]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
data and metadata/control information between vehicles and PSAPs.
Refer to [TBD: THIS DOCUMENT] for more information.
12.2. Applicability
This section describes "why the Info Package mechanism, rather than
some other mechanism, has been chosen for the specific use-case...."
The use of INFO is based on an analysis of the requirements against
the intent and effects of INFO versus other approaches (which
included SIP MESSAGE, SIP OPTIONS, SIP re-INVITE, media plane
transport, and non-SIP protocols). In particular, the transport of
emergency call data blocks occurs within a SIP emergency dialog, per
Section 7, and is normally carried in the initial INVITE and its
response; the use of INFO only occurs when emergency-call-related
data needs to be sent mid-call. While MESSAGE could be used, it is
not tied to a SIP dialog as is INFO and thus might not be associated
with the dialog. SIP OPTIONS or re-INVITE could also be used, but is
seen as less clean than INFO. SUBSCRIBE/NOTIFY could be coerced into
service, but the semantics are not a good fit, e.g., the subscribe/
notify mechanism provides one-way communication consisting of (often
multiple) notifications from notifier to subscriber indicating that
certain events in notifier have occurred, whereas what's needed here
is two-way communication of data related to the emergency dialog.
Use of the media plane mechanisms was discounted because the number
of messages needing to be exchanged in a dialog is normally zero or
very few, and the size of the data is likewise very small. The
overhead caused by user plane setup (e.g., to use MSRP as transport)
would be disproportionately large.
Based on the the analyses, the SIP INFO method was chosen to provide
for mid-call data transport.
12.3. Info Package Name
The info package name is emergencyCallData.eCall.VEDS
12.4. Info Package Parameters
None
12.5. SIP Option-Tags
None
Gellens, et al. Expires April 21, 2017 [Page 23]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
12.6. INFO Request Body Parts
The body for an emergencyCallData.eCall.VEDS info package is a
multipart body which MAY contain zero or one application/
emergencyCallData.eCall.VEDS+xml (containing a VEDS data block) part,
zero or more application/emergencyCallData.control+xml (containing a
metadata/control object) parts, and zero or one application/
emergencyCallData.eCall.MSD+per (containing an MSD) part. At least
one VEDS, MSD, or metadata/control body part is expected; the
behavior upon receiving an INFO request with none is undefined.
The body parts are sent per [RFC6086], and in addition, to align with
with how these body parts are sent in non-INFO messages, each
associated body part is referenced by a Call-Info header field at the
top level of the SIP message. The body part has a Content-
Disposition header field set to "By-Reference".
A VEDS or metadata/control block is always enclosed in a multipart
body part (even if it would otherwise be the only body part in the
SIP message), since as of the date of this document, the use of
Content-ID as a SIP header field is not defined (while it is defined
for use as a MIME header field). The innermost multipart that
contains only body parts associated with the INFO package has a
Content-Disposition value of Info-Package.
Service providers are not expected to attach [RFC7852] Additional
Data to an INFO request.
See [TBD: THIS DOCUMENT] for more information.
12.7. Info Package Usage Restrictions
Usage is limited to vehicle-initiated emergency calls as defined in
[TBD: THIS DOCUMENT].
12.8. Rate of INFO Requests
The SIP INFO request is used within an established emergency call
dialog for the PSAP to request the IVS to send an updated data set,
and for the IVS to send the requested data set. Because this is
normally done only on manual request of the PSAP call taker (who
suspects some aspect of the vehicle state has changed), the rate of
SIP INFO requests associated with the emergencyCallData.eCall.VEDS
info package is normally quite low (most dialogs are likely to
contain zero INFO requests, while others can be expected to carry an
occasional request).
Gellens, et al. Expires April 21, 2017 [Page 24]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
12.9. Info Package Security Considerations
The MIME media type registations for the data blocks that can be
carried using this INFO package contains a discussion of the security
and/or privacy considerations specific to that data block. The
"Security Considerations" and "Privacy Considerations" sections of
[TBD: THIS DOCUMENT] discuss security and privacy considerations of
the data carried in vehicle-initiated emergency calls as described in
that document.
12.10. Implementation Details
See [TBD: THIS DOCUMENT] for protocol details.
12.11. Examples
See [TBD: THIS DOCUMENT] for protocol examples.
13. Example
Figure 10 shows an NG-ACN call routing. The mobile network operator
(MNO) routes the call to an Emergency services IP Network (ESInet),
as for any emergency call. The ESInet routes the call to an
appropriate NG-ACN-capable PSAP (using location information and the
fact that that it is an NG-ACN call). The call is processed by the
Emergency Services Routing Proxy (ESRP), as the entry point to the
ESInet. The ESRP routes the call to an appropriate NG-ACN-capable
PSAP, where the call is received by a call taker. (In deployments
where there is no ESInet, the MNO itself routes the call directly to
an appropriate NG-ACN-capable PSAP.)
Gellens, et al. Expires April 21, 2017 [Page 25]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
+---------------------------------------+
| |
+------------+ | +-------+ |
| | | | PSAP2 | |
| | | +-------+ |
| Originating| | |
| Mobile | | +------+ +-------+ |
Vehicle-->| Network |--+->| ESRP |---->| PSAP1 |--> Call-Taker |
| | | +------+ +-------+ |
| | | |
+------------+ | +-------+ |
| | PSAP3 | |
| +-------+ |
| |
| |
| |
| ESInet |
+---------------------------------------+
Figure 10: Example of Vehicle-Placed Emergency Call Message Flow
The example, shown in Figure 11, illustrates a SIP emergency call
INVITE with location information (a PIDF-LO), VEDS crash data (a VEDS
data block), and capabilities data (a metadata/control block with
extensions defined in this document) attached to the SIP INVITE
message. The INVITE has a request URI containing the
'urn:service:sos.ecall.automatic' service URN.
The example VEDS data structure shows information about about a
crashed vehicle. The example communicates that the car is a model
year 2015 Saab 9-5 (a car which does not exist). The front airbag
deployed as a consequence of the crash. The
'VehicleBodyCategoryCode' indicates that the crashed vehicle is a
passenger car (the code is set to '101') and that it is not a
convertible (the 'ConvertibleIndicator' value is set to 'false').
The 'VehicleCrashPulse' element provides further information about
the crash, namely that the force of impact based on the change in
velocity over the duration of the crash pulse was 100 MPH. The
principal direction of the force of the impact is set to '12' (which
refers to 12 O'Clock, corresponding to a frontal collision). This
value is described in the 'CrashPulsePrincipalDirectionOfForceValue'
element.
The 'CrashPulseRolloverQuarterTurnsValue' indicates the number of
quarter turns in concert with a rollover expressed as a number; in
our case 1.
Gellens, et al. Expires April 21, 2017 [Page 26]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
No roll bar was deployed, as indicated in
'VehicleRollbarDeployedIndicator' being set to 'false'.
Next, there is information indicating seatbelt and seat sensor data
for individual seat positions in the vehicle. In our example,
information from the driver seat is available (value '1' in the
'VehicleSeatLocationCategoryCode' element), that the seatbelt was
monitored ('VehicleSeatbeltMonitoredIndicator' element), that the
seatbelt was fastened ('VehicleSeatbeltFastenedIndicator' element)
and the seat sensor determined that the seat was occupied
('VehicleSeatOccupiedIndicator' element).
Finally, information about the weight of the vehicle, which is 600
kilogram in our example.
In addition to the information about the vehicle, further indications
are provided, namely the presence of fuel leakage
('FuelLeakingIndicator' element), an indication whether the vehicle
was subjected to multiple impacts ('MultipleImpactsIndicator'
element), the orientation of the vehicle at final rest
('VehicleFinalRestOrientationCategoryCode' element) and an indication
that there are no parts of the vehicle on fire (the
'VehicleFireIndicator' element).
INVITE urn:service:sos.ecall.automatic SIP/2.0
To: urn:service:sos.ecall.automatic
From: <sip:+13145551111@example.com>;tag=9fxced76sl
Call-ID: 3848276298220188511@atlanta.example.com
Geolocation: <cid:target123@example.com>
Geolocation-Routing: no
Call-Info: <cid:1234567890@atlanta.example.com>;
purpose=EmergencyCallData.VEDS
Call-Info: <cid:1234567892@atlanta.example.com>;
purpose=emergencyCallData.control
Accept: application/sdp, application/pidf+xml,
application/emergencyCallData.control+xml
Recv-Info: emergencyCallData.eCall
Allow: INVITE, ACK, PRACK, INFO, OPTIONS, CANCEL, REFER, BYE,
SUBSCRIBE, NOTIFY, UPDATE
CSeq: 31862 INVITE
Content-Type: multipart/mixed; boundary=boundary1
Content-Length: ...
--boundary1
Content-Type: application/sdp
...Session Description Protocol (SDP) goes here
Gellens, et al. Expires April 21, 2017 [Page 27]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
--boundary1
Content-Type: application/pidf+xml
Content-ID: <target123@atlanta.example.com>
Content-Disposition: by-reference;handling=optional
<?xml version="1.0" encoding="UTF-8"?>
<presence
xmlns="urn:ietf:params:xml:ns:pidf"
xmlns:dm="urn:ietf:params:xml:ns:pidf:data-model"
xmlns:gp="urn:ietf:params:xml:ns:pidf:geopriv10"
xmlns:dyn="urn:ietf:params:xml:ns:pidf:geopriv10:dynamic"
xmlns:gml="http://www.opengis.net/gml"
xmlns:gs="http://www.opengis.net/pidflo/1.0"
entity="sip:+13145551111@example.com">
<dm:device id="123">
<gp:geopriv>
<gp:location-info>
<gml:Point srsName="urn:ogc:def:crs:EPSG::4326">
<gml:pos>-34.407 150.883</gml:pos>
</gml:Point>
<dyn:Dynamic>
<dyn:heading>278</dyn:heading>
<dyn:direction><dyn:direction>
</dyn:Dynamic>
</gp:location-info>
<gp:usage-rules/>
<method>gps</method>
</gp:geopriv>
<timestamp>2012-04-5T10:18:29Z</timestamp>
<dm:deviceID>1M8GDM9A_KP042788</dm:deviceID>
</dm:device>
</presence>
--boundary1
Content-Type: application/EmergencyCallData.VEDS+xml
Content-ID: <1234567890@atlanta.example.com>
Content-Disposition: by-reference;handling=optional
<?xml version="1.0" encoding="UTF-8"?>
<AutomatedCrashNotification xmlns="http://www.veds.org/acn/1.0"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
<Crash>
<CrashVehicle>
<ItemMakeName xmlns="http://niem.gov/niem/niem-core/2.0">
Saab
</ItemMakeName>
<ItemModelName xmlns="http://niem.gov/niem/niem-core/2.0">
Gellens, et al. Expires April 21, 2017 [Page 28]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
9-5
</ItemModelName>
<ItemModelYearDate
xmlns="http://niem.gov/niem/niem-core/2.0">
2015
</ItemModelYearDate>
<Airbag>
<AirbagCategoryCode>FRONT</AirbagCategoryCode>
<AirbagDeployedIndicator>true
</AirbagDeployedIndicator>
</Airbag>
<ConvertibleIndicator>false</ConvertibleIndicator>
<PowerSourceCategoryCode>MAIN</PowerSourceCategoryCode>
<VehicleBodyCategoryCode
xmlns="http://niem.gov/niem/domains/jxdm/4.1">
101
</VehicleBodyCategoryCode>
<VehicleCrashPulse>
<CrashPulseChangeInVelocityMeasure>
<MeasurePointValue
xmlns="http://niem.gov/niem/niem-core/2.0">
100
</MeasurePointValue>
<MeasureUnitText
xmlns="http://niem.gov/niem/niem-core/2.0">
MPH</MeasureUnitText>
</CrashPulseChangeInVelocityMeasure>
<CrashPulsePrincipalDirectionOfForceValue>12
</CrashPulsePrincipalDirectionOfForceValue>
<CrashPulseRolloverQuarterTurnsValue>1
</CrashPulseRolloverQuarterTurnsValue>
</VehicleCrashPulse>
<VehicleRollbarDeployedIndicator>false
</VehicleRollbarDeployedIndicator>
<VehicleSeat>
<VehicleSeatLocationCategoryCode>1
</VehicleSeatLocationCategoryCode>
<VehicleSeatOccupiedIndicator>true
</VehicleSeatOccupiedIndicator>
<VehicleSeatbeltFastenedIndicator>true
</VehicleSeatbeltFastenedIndicator>
<VehicleSeatbeltMonitoredIndicator>true
</VehicleSeatbeltMonitoredIndicator>
</VehicleSeat>
<VehicleUnladenWeightMeasure
xmlns="http://niem.gov/niem/niem-core/2.0">
<MeasurePointValue
xmlns="http://niem.gov/niem/niem-core/2.0">
Gellens, et al. Expires April 21, 2017 [Page 29]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
600
</MeasurePointValue>
<MeasureUnitText
xmlns="http://niem.gov/niem/niem-core/2.0">
kilogram
</MeasureUnitText>
</VehicleUnladenWeightMeasure>
</CrashVehicle>
<FuelLeakingIndicator>true</FuelLeakingIndicator>
<MultipleImpactsIndicator>false</MultipleImpactsIndicator>
<SevereInjuryIndicator>true</SevereInjuryIndicator>
<VehicleFinalRestOrientationCategoryCode>Driver
</VehicleFinalRestOrientationCategoryCode>
<VehicleFireIndicator>false</VehicleFireIndicator>
</Crash>
</AutomatedCrashNotification>
--boundary1
Content-Type: application/emergencyCallData.control+xml
Content-ID: <1234567892@atlanta.example.com>
Content-Disposition: by-reference;handling=optional
<?xml version="1.0" encoding="UTF-8"?>
<EmergencyCallData.control
xmlns="urn:ietf:params:xml:ns:EmergencyCallData:control"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<capabilities>
<request action="send-data" supported-datatypes="VEDS"/>
<request action="lamp"
supported-values="head;interior;fog-front;fog-rear;
brake;position-front;position-rear;turn-left;
turn-right;hazard"/>
<request action="msg-static" msgid="3"/>
<request action="msg-dynamic"/>
<request action="honk"/>
<request action="enable-camera"
supported-values="backup; interior"/>
</capabilities>
</EmergencyCallData.control>
--boundary1--
Figure 11: SIP INVITE for a Vehicle-Initated Emergency Call
Gellens, et al. Expires April 21, 2017 [Page 30]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
14. Security Considerations
Since this document relies on [I-D.ietf-ecrit-ecall] and [RFC7852],
the security considerations described there and in [RFC5069] apply
here. Implementors are cautioned to read and understand the
discussion in those documents.
As with emergency service systems where location data is supplied or
determined with the assistance of an end host, there is the
possibility that that location is incorrect, either intentially
(e.g., in a denial of service attack against the emergency services
infrastructure) or due to a malfunctioning device. The reader is
referred to [RFC7378] for a discussion of some of these
vulnerabilities.
In addition to the security considerations discussion specific to the
metadata/control object in [I-D.ietf-ecrit-ecall], note that vehicles
MAY decline to carry out any requested action (e.g., if the vehicle
requires but is unable to verify the certificate used to sign the
request). The vehicle MAY use any value in the reason registry to
indicate why it did not take an action (e.g., the generic "unable" or
the more specific "security-failure").
15. Privacy Considerations
Since this document builds on [I-D.ietf-ecrit-ecall], which itself
builds on [RFC7852], the data structures specified there, and the
corresponding privacy considerations discussed there, apply here as
well. The VEDS data structure contains optional elements that can
carry identifying and personal information, both about the vehicle
and about the owner, as well as location information, and so needs to
be protected against unauthorized disclosure, as discussed in
[RFC7852]. Local regulations may impose additional privacy
protection requirements.
The additional functionality enabled by this document, such as access
to vehicle camera streams, carries a burden of protection and so
implementations need to be careful that access is only provided
within the context of an emergency call or to an emergency services
provider (e.g., by verifying that the request for camera access is
signed by a certificate issued by an emergency services registrar).
16. IANA Considerations
This document registers the 'application/EmergencyCall.VEDS+xml' MIME
media type, and adds "VEDS" to the Emergency Call Additional Data
registry. This document adds to and creates sub-registries in the
Gellens, et al. Expires April 21, 2017 [Page 31]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
'Metadata/Control Data' registry created in [I-D.ietf-ecrit-ecall].
This document registers a new INFO package.
16.1. MIME Media Type Registration for 'application/
EmergencyCall.VEDS+xml'
This specification requests the registration of a new MIME media type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: EmergencyCallData.VEDS+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Encoding considerations: Uses XML, which can employ 8-bit
characters, depending on the character encoding used. See
Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This media type is designed to carry vehicle crash data during
an emergency call.
This data can contain personal information including vehicle
VIN, location, direction, etc. Appropriate precautions need to
be taken to limit unauthorized access, inappropriate disclosure
to third parties, and eavesdropping of this information.
Please refer to Section 7 and Section 8 of [RFC7852] for more
information.
When this media type is contained in a signed or encrypted body
part, the enclosing multipart (e.g., multipart/signed or
multipart/encrypted) has the same Content-ID as the data part.
This allows an entity to identify and access the data blocks it
is interested in without having to dive deeply into the message
structure or decrypt parts it is not interested in. (The
'purpose' parameter in a Call-Info header field identifies the
data, and the CID URL points to the data block in the body,
which has a matching Content-ID body part header field).
Interoperability considerations: None
Gellens, et al. Expires April 21, 2017 [Page 32]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
Published specification: [VEDS]
Applications which use this media type: Emergency Services
Additional information: None
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Persons and email addresses for further information: Randall
Gellensm rg+ietf@randy.pensive.org; Hannes Tschofenig,
Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
16.2. Registration of the 'VEDS' entry in the Emergency Call Additional
Data registry
This specification requests IANA to add the 'VEDS' entry to the
Emergency Call Additional Data registry, with a reference to this
document. The Emergency Call Additional Data registry was
established by [RFC7852].
16.3. New Action Values
This document adds new values for the 'action' attribute of the
<request> element in the "Action Registry" registry created by
[I-D.ietf-ecrit-ecall].
Gellens, et al. Expires April 21, 2017 [Page 33]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
+---------------+--------------------------------------+
| Name | Description |
+---------------+--------------------------------------+
| msg-static | Section 10.1 of [TBD: THIS DOCUMENT] |
| | |
| msg-dynamic | Section 10.1 of [TBD: THIS DOCUMENT] |
| | |
| honk | Section 10.1 of [TBD: THIS DOCUMENT] |
| | |
| lamp | Section 10.1 of [TBD: THIS DOCUMENT] |
| | |
| enable-camera | Section 10.1 of [TBD: THIS DOCUMENT] |
+---------------+--------------------------------------+
Table 2: Action Registry New Values
16.4. Static Message Registry
This document creates a new sub-registry called "Static Message
Registry" in the "Metadata/Control Data" registry established by
[I-D.ietf-ecrit-ecall]. Because all compliant vehicles are expected
to support all static messages translated into all languages
supported by the vehicle, it is important to limit the number of such
messages. As defined in [RFC5226], this registry operates under
"Publication Required" rules, which require a stable, public document
and implies expert review of the publication. The expert should
determine that the document has been published by an appropriate
emergency services organization (e.g., NENA, EENA, APCO) or by the
IETF with input from an emergency services organization, and that the
proposed message is sufficiently distinguishable from other messages.
The contents of this registry are:
ID: An integer identifier to be used in the 'msgid' attribute of a
metadata/control <request> element.
Message: The text of the message. Messages are listed in the
registry in English; vehicles are expected to implement
translations into languages supported by the vehicle.
When new messages are added to the registry, the message text is
determined by the registrant; IANA assigns the IDs. Each message is
assigned a consecutive integer value as its ID. This allows an IVS
to indicate by a single integer value that it supports all messages
with that value or lower.
The initial set of values is listed in Table 3.
Gellens, et al. Expires April 21, 2017 [Page 34]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
+----+--------------------------------------------------------------+
| ID | Message |
+----+--------------------------------------------------------------+
| 1 | Emergency authorities are aware of your incident and |
| | location, but are unable to speak with you right now. We |
| | will help you as soon as possible. |
+----+--------------------------------------------------------------+
Table 3: Static Message Registry
16.5. Lamp ID Registry
This document creates a new sub-registry called "Lamp ID Registry" in
the "Metadata/Control Data" registry established by
[I-D.ietf-ecrit-ecall]. This new sub-registry uniquely identifies
the names of automotive lamps (lights). As defined in [RFC5226],
this registry operates under "Expert Review" rules. The expert
should determine that the proposed lamp name is clearly
understandable and is sufficiently distinguishable from other lamp
names.
The contents of this registry are:
Name: The identifier to be used in the 'lamp-ID' attribute of a
metadata/control <request> element.
Description: A description of the lamp (light).
The initial set of values is listed in Table 4.
Gellens, et al. Expires April 21, 2017 [Page 35]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
+----------------+---------------------------------------------+
| Name | Description |
+----------------+---------------------------------------------+
| head | The main lamps used to light the road ahead |
| | |
| interior | Interior lamp, often at the top center |
| | |
| fog-front | Front fog lamps |
| | |
| fog-rear | Rear fog lamps |
| | |
| brake | Brake indicator lamps |
| | |
| brake-center | Center High Mounted Stop Lamp |
| | |
| position-front | Front position/parking/standing lamps |
| | |
| position-rear | Rear position/parking/standing lamps |
| | |
| turn-left | Left turn/directional lamps |
| | |
| turn-right | Right turn/directional lamps |
| | |
| hazard | Hazard/four-way lamps |
+----------------+---------------------------------------------+
Table 4: Lamp ID Registry Initial Values
16.6. Camera ID Registry
This document creates a new sub-registry called "Camera ID Registry"
in the "Metadata/Control Data" registry established by
[I-D.ietf-ecrit-ecall]. This new sub-registry uniquely identifies
automotive cameras. As defined in [RFC5226], this registry operates
under "Expert Review" rules. The expert should determine that the
proposed camera name is clearly understandable and is sufficiently
distinguishable from other camera names.
The contents of this registry are:
Name: The identifier to be used in the 'camera-ID' attribute of a
control <request> element.
Description: A description of the camera.
The initial set of values is listed in Table 5.
Gellens, et al. Expires April 21, 2017 [Page 36]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
+-------------+-----------------------------------------------------+
| Name | Description |
+-------------+-----------------------------------------------------+
| backup | Shows what is behind the vehicle, e.g., often used |
| | for driver display when the vehicle is in reverse. |
| | Also known as rearview, reverse, rear visibility, |
| | etc. |
| | |
| left-rear | Shows view to the left and behind (e.g., left side |
| | rear-view mirror or blind spot view) |
| | |
| right-rear | Shows view to the right and behind (e.g., right |
| | side rear-view mirror or blind spot view) |
| | |
| forward | Shows what is in front of the vehicle |
| | |
| rear-wide | Shows what is behind vehicle (e.g., used by rear- |
| | collision detection systems), separate from backup |
| | view |
| | |
| lane | Used by systems to identify road lane and/or |
| | monitor vehicle's position within lane |
| | |
| interior | Shows the interior (e.g., driver) |
| | |
| night-front | Night-vision view of what is in front of the |
| | vehicle |
+-------------+-----------------------------------------------------+
Table 5: Camera ID Registry Initial Values
17. Acknowledgements
We would like to thank Lena Chaponniere, Stephen Edge, and Christer
Holmberg for their review and suggestions; Robert Sparks and Paul
Kyzivat for their help with the SIP mechanisms; Michael Montag,
Arnoud van Wijk, Ban Al-Bakri, Wes George, Gunnar Hellstrom, and Rex
Buddenberg for their feedback; and Ulrich Dietz for his help with
earlier versions of the original version of this document.
18. Changes from Previous Versions
18.1. Changes from draft-ietf-17 to draft-ietf-18
o Added additional text to "Rate of Info Requests"
o Further corrected "content type" to "media type"
Gellens, et al. Expires April 21, 2017 [Page 37]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
18.2. Changes from draft-ietf-16 to draft-ietf-17
o Clarified that an INFO request is expected to have at least one
VEDS, MSD or metadata/control body part
o Corrected "content type" to "media type"
18.3. Changes from draft-ietf-14 to draft-ietf-15
o Moved VEDS text from Introduction to new Vehicle Data section
o Various clarifications and simplifications
18.4. Changes from draft-ietf-13 to draft-ietf-14
o Body parts now always sent enclosed in multipart (even if only
body part in SIP message) and hence always have a Content-
Disposition of By-Reference
o Fixed typos.
18.5. Changes from draft-ietf-11 to draft-ietf-13
o Fixed typos
18.6. Changes from draft-ietf-10 to draft-ietf-11
o Clarifications suggested by Christer
o Corrections to Content-Disposition text and examples as suggested
by Paul Kyzivat
o Clarifications to Content-Disposition text and examples to clarify
that handling=optional is only used in the initial INVITE
18.7. Changes from draft-ietf-09 to draft-ietf-10
o Fixed errors in examples found by Dale in eCall draft
o Removed enclosing sub-section of INFO package registration section
o Added text per Christer and Dale's suggestions that the MSD and
metadata/control blocks are sent in INFO with a Call-Info header
field referencing them
o Other text changes per comments received from Christer and Ivo
against eCall draft.
18.8. Changes from draft-ietf-08 to draft-ietf-09
o Added INFO package registration for eCall.VEDS
o Moved <capabilities> element and other extension points back to
eCall document so that extension points are in base spec (and also
to get XML schema to compile)
o Text changes for clarification.
Gellens, et al. Expires April 21, 2017 [Page 38]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
18.9. Changes from draft-ietf-07 to draft-ietf-08
o Moved much of the metadata/control object from
[I-D.ietf-ecrit-ecall] to this document as extensions
o Editorial clarifications and simplifications
o Moved "Call Routing" to be a subsection of "Call Setup"
o Deleted "Profile" section and moved some of its text into
"Introduction"
18.10. Changes from draft-ietf-06 to draft-ietf-07
o Minor editorial changes
18.11. Changes from draft-ietf-05 to draft-ietf-06
o Added clarifying text regarding signed and encrypted data
o Additional informative text in "Migration to Next-Generation"
section
o Additional clarifying text regarding security and privacy.
18.12. Changes from draft-ietf-04 to draft-ietf-05
o Reworded security text in main document and in MIME registration
for the VEDS object
18.13. Changes from draft-ietf-03 to draft-ietf-04
o Added example VEDS object
o Additional clarifications and corrections
o Removed references from Abstract
o Moved Document Scope section to follow Introduction
18.14. Changes from draft-ietf-02 to draft-ietf-03
o Additional clarifications and corrections
18.15. Changes from draft-ietf-01 to draft-ietf-02
o This document now refers to [I-D.ietf-ecrit-ecall] for technical
aspects including the service URN; this document no longer
proposes a unique service URN for non-eCall NG-ACN calls; the same
service URN is now used for all NG-ACN calls including NG-eCall
and non-eCall
o Added discussion of an NG-ACN call placed to a PSAP that doesn't
support it
o Minor wording improvements and clarifications
Gellens, et al. Expires April 21, 2017 [Page 39]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
18.16. Changes from draft-ietf-00 to draft-ietf-01
o Added further discussion of test calls
o Added further clarification to the document scope
o Mentioned that multi-region vehicles may need to support other
crash notification specifications such as eCall
o Minor wording improvements and clarifications
18.17. Changes from draft-gellens-02 to draft-ietf-00
o Renamed from draft-gellens- to draft-ietf-
o Added text to Introduction to clarify that during a CS ACN, the
PSAP call taker usually needs to listen to the data and transcribe
it
18.18. Changes from draft-gellens-01 to -02
o Fixed case of 'EmergencyCallData', in accordance with changes to
[RFC7852]
18.19. Changes from draft-gellens-00 to -01
o Now using 'EmergencyCallData' for purpose parameter values and
MIME subtypes, in accordance with changes to [RFC7852]
o Added reference to RFC 6443
o Fixed bug that caused Figure captions to not appear
19. References
19.1. Normative References
[I-D.ietf-ecrit-ecall]
Gellens, R. and H. Tschofenig, "Next-Generation Pan-
European eCall", draft-ietf-ecrit-ecall-17 (work in
progress), October 2016.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC3023] Murata, M., St. Laurent, S., and D. Kohn, "XML Media
Types", RFC 3023, DOI 10.17487/RFC3023, January 2001,
<http://www.rfc-editor.org/info/rfc3023>.
[RFC4119] Peterson, J., "A Presence-based GEOPRIV Location Object
Format", RFC 4119, DOI 10.17487/RFC4119, December 2005,
<http://www.rfc-editor.org/info/rfc4119>.
Gellens, et al. Expires April 21, 2017 [Page 40]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
[RFC4288] Freed, N. and J. Klensin, "Media Type Specifications and
Registration Procedures", RFC 4288, DOI 10.17487/RFC4288,
December 2005, <http://www.rfc-editor.org/info/rfc4288>.
[RFC5031] Schulzrinne, H., "A Uniform Resource Name (URN) for
Emergency and Other Well-Known Services", RFC 5031,
DOI 10.17487/RFC5031, January 2008,
<http://www.rfc-editor.org/info/rfc5031>.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
DOI 10.17487/RFC5226, May 2008,
<http://www.rfc-editor.org/info/rfc5226>.
[RFC5491] Winterbottom, J., Thomson, M., and H. Tschofenig, "GEOPRIV
Presence Information Data Format Location Object (PIDF-LO)
Usage Clarification, Considerations, and Recommendations",
RFC 5491, DOI 10.17487/RFC5491, March 2009,
<http://www.rfc-editor.org/info/rfc5491>.
[RFC5962] Schulzrinne, H., Singh, V., Tschofenig, H., and M.
Thomson, "Dynamic Extensions to the Presence Information
Data Format Location Object (PIDF-LO)", RFC 5962,
DOI 10.17487/RFC5962, September 2010,
<http://www.rfc-editor.org/info/rfc5962>.
[RFC6443] Rosen, B., Schulzrinne, H., Polk, J., and A. Newton,
"Framework for Emergency Calling Using Internet
Multimedia", RFC 6443, DOI 10.17487/RFC6443, December
2011, <http://www.rfc-editor.org/info/rfc6443>.
[RFC6881] Rosen, B. and J. Polk, "Best Current Practice for
Communications Services in Support of Emergency Calling",
BCP 181, RFC 6881, DOI 10.17487/RFC6881, March 2013,
<http://www.rfc-editor.org/info/rfc6881>.
[RFC7852] Gellens, R., Rosen, B., Tschofenig, H., Marshall, R., and
J. Winterbottom, "Additional Data Related to an Emergency
Call", RFC 7852, DOI 10.17487/RFC7852, July 2016,
<http://www.rfc-editor.org/info/rfc7852>.
[VEDS] Advanced Automatic Crash Notification (AACN) Joint APCO/
NENA Data Standardization Workgroup, , "Vehicular
Emergency Data Set (VEDS) version 3", July 2012,
<https://www.apcointl.org/resources/telematics/aacn-and-
veds.html>.
Gellens, et al. Expires April 21, 2017 [Page 41]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
19.2. Informative references
[RFC5012] Schulzrinne, H. and R. Marshall, Ed., "Requirements for
Emergency Context Resolution with Internet Technologies",
RFC 5012, DOI 10.17487/RFC5012, January 2008,
<http://www.rfc-editor.org/info/rfc5012>.
[RFC5069] Taylor, T., Ed., Tschofenig, H., Schulzrinne, H., and M.
Shanmugam, "Security Threats and Requirements for
Emergency Call Marking and Mapping", RFC 5069,
DOI 10.17487/RFC5069, January 2008,
<http://www.rfc-editor.org/info/rfc5069>.
[RFC6086] Holmberg, C., Burger, E., and H. Kaplan, "Session
Initiation Protocol (SIP) INFO Method and Package
Framework", RFC 6086, DOI 10.17487/RFC6086, January 2011,
<http://www.rfc-editor.org/info/rfc6086>.
[RFC7378] Tschofenig, H., Schulzrinne, H., and B. Aboba, Ed.,
"Trustworthy Location", RFC 7378, DOI 10.17487/RFC7378,
December 2014, <http://www.rfc-editor.org/info/rfc7378>.
[triage-2008]
National Center for Injury Prevention and Control, and
Centers for Disease Control and Prevention,
"Recommendations from the Expert Panel: Advanced Automatic
Collision Notification and Triage of the Injured Patient",
2008, <https://stacks.cdc.gov/view/cdc/5304/>.
[triage-2011]
National Center for Injury Prevention and Control, and
Centers for Disease Control and Prevention, "Guidelines
for field triage of injured patients: recommendations of
the National Expert Panel on Field Triage", January 2012,
<https://www.researchgate.net/journal/1545-8601_MMWR_Recom
mendations_and_reports_Morbidity_and_mortality_weekly_repo
rt_Recommendations_and_reports_Centers_for_Disease_Control
>.
Authors' Addresses
Randall Gellens
Core Technology Consulting
Email: rg+ietf@randy.pensive.org
Gellens, et al. Expires April 21, 2017 [Page 42]
Internet-Draft Vehicle-Initiated Emergency Calls October 2016
Brian Rosen
NeuStar, Inc.
470 Conrad Dr
Mars, PA 16046
US
Email: br@brianrosen.net
Hannes Tschofenig
Individual
Email: Hannes.Tschofenig@gmx.net
URI: http://www.tschofenig.priv.at
Gellens, et al. Expires April 21, 2017 [Page 43]