TOC 
ECRITJ. Winterbottom
Internet-DraftM. Thomson
Intended status: BCPAndrew Corporation
Expires: September 25, 2010March 24, 2010


Specifying Holes in LoST Service Boundaries
draft-ietf-ecrit-specifying-holes-03

Abstract

This document describes how holes can be specified in geodetic service boundaries. One means of implementing a search solution in a service database, such as one might provide with a LoST server, is described.

Status of this Memo

This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.

This Internet-Draft will expire on September 25, 2010.

Copyright Notice

Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License.



Table of Contents

1.  Introduction
2.  Terminology
3.  Specifying Holes
4.  GML Polygons
5.  Holes in GML Polygons
6.  Service Boundary Specification and Selection Algorithm
7.  Security Considerations
8.  IANA Considerations
9.  Acknowledgements
10.  References
    10.1.  Normative References
    10.2.  Informative References
§  Authors' Addresses




 TOC 

1.  Introduction

The LoST protocol [RFC5222] (Hardie, T., Newton, A., Schulzrinne, H., and H. Tschofenig, “LoST: A Location-to-Service Translation Protocol,” August 2008.) maps service and locations to destination addresses. A LoST server does this by provisioning boundary maps or areas against service URNs. The boundary is a polygon made up of sets of geodetic coordinates specifying an enclosed area. In some circumstances an area enclosed by a polygon, also known as an exterior polygon, may contain exception areas, or holes, that for the same service must yield a different destination to that described by the larger area.

This document describes the RECOMMENDED approach to specifying holes in service boundaries defined using a GML encoding for the polygons and their internal elements (holes).



    o--------------o
   /                \
  /    /\            \
 /    + +-----+       \
o     |  Hole  \       o
|     |    1   /       |
|     +-------+        |<--- Primary Polygon
|        +-------+     |
|       /  Hole  |     |
o       \   2    |     o
 \       +-----+ +    /
  \             \/   /
   \                /
    o--------------o

 Figure 1: Holes in a Polygon 

This document describes a profile of Geographic Markup Language (GML) (ISO, “Geographic information - Spatial Schema,” 5 2003.) [ISO‑19107] polygons that constrains their representation when used for describing service boundaries.

The working group considered that the types of regions described in this memo could be represented in various ways as polygons without holes, but concluded on the recommendations here to avoid potential problems with the arbitrary division of regions and to align with existing geospatial system practices.



 TOC 

2.  Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).



 TOC 

3.  Specifying Holes

Holes related to an exterior boundary polygon MUST adhere to the following rules:

Rule 1:
Two holes MUST NOT have more than one point of intersection.

If two or more holes overlap or share a common boundary then these represent a single hole. The internal elements (holes) should have common boundaries removed and a single hole created irrespective of whether the excluded area is itself made up of multiple service boundaries.



    o--------------o                      o--------------o
   /                \                    /                \
  /    /\            \                  /    /\            \
 /    + +-----+       \                /    + +-----+       \
o     |  Hole  \       o              o     |        \       o
|     |    1    \      |              |     |  One    \      |
|     +-+-------+      |  =========>  |     +-+  Hole +      |
|       /  Hole  |     |              |       /        |     |
o       \   2    |     o              o       \        |     o
 \       +-----+ +    /                \       +-----+ +    /
  \             \/   /                  \             \/   /
   \                /                    \                /
    o--------------o                      o--------------o

       Incorrect                              Correct

 Figure 2: Hole Specification with Boundary Sharing 

Rule 2:
A polygon MUST describe a contiguous region.

If a hole overlaps with the outer boundary, or it shares part of a side with the outer boundary, then it has an inlet and it MUST be expressed without the hole.



           +------- Inlet
           |
           v
    o---+-----+----o                     o---o     o----o
   /    |%%%%%|     \                   /    |     |     \
  /    /%%%%%%|      \                 /    /      |      \
 /    +%%%%%%%|       \               /    o       o       \
o     |%%%%%%%%\       o             o     |        \       o
|     |%%%%%%%%%\      |             |     |         \      |
|     +-+%%%%%%%%+     |  ========>  |     o-o        o     |
|       /%%%%%%%%|     |             |       /        |     |
o       \%%%%%%%%|     o             o       \        |     o
 \       +-----+ +    /               \       o-----o o    /
  \             \/   /                 \             \/   /
   \                /                   \                /
    o--------------o                     o--------------o

       Incorrect                             Correct

 Figure 3: Specification of an Inlet 

If a hole touches the outer boundary in two places, the region MUST be expressed as two separate polygons.



    A--q-----------B                     A-q   q----------B
   /  | |           \                   /  |   |           \
  /   | |            \                 /   |   |            \
 /    z r-----s       \               / P  z   r-----s   P   \
H     |        \       C             H  o  |          \   o   C
|     |  One    \      |             |  l  |           \   l  |
|     y-x  Hole  t     |  ========>  |  y  y-x          t  y  |
|       /        |     |             |  g    /          |  g  |
G       \        |     D             G  o    \          |  o  D
 \      /    v---u    /               \ n    /      v---u  n /
  \     \   /        /                 \  1  \     /      2 /
   \     \ /        /                   \     \   /        /
    F-----w--------E                     F-----w w--------E

       Incorrect                               Correct

 Figure 4: Specification of Hole with Multiple Outer-Boundary Intersections 

Similarly, a polygon that is enclosed entirely within a hole from another polygon (i.e., an "island") is a separate polygon.



       o--------------o
      /                \
     / +--------------+ \
    /  |%%%%%%%%%%%%%%|  \
   o   |%%o--------o%%|   o
   |   |%/  Island  \%|   |
   |   |%\          /%|   |
   |   |%%o--------o%%|   |
   o   |%%%%%%%%%%%%%%|   o
    \  +--------------+  /
     \                  /
      \                /
       o--------------o

 Figure 5: Holes With Enclosed Polygon (Island) 

Rule 3:
A hole MUST be formed from a legal linear ring in accordance with [geoshape] (Thomson, M. and C. Reed, “GML 3.1.1 PIDF-LO Shape Application Schema for use by the Internet Engineering Task Force (IETF),” April 2007.), except that points are specified in a clockwise direction.

Holes are specified in clockwise direction so that the upward normal is opposed to the upward normal of the exterior boundary of the polygon. Note that [geoshape] (Thomson, M. and C. Reed, “GML 3.1.1 PIDF-LO Shape Application Schema for use by the Internet Engineering Task Force (IETF),” April 2007.) stipulates that exterior boundaries are specified in anti-clockwise order.

There is no restriction on the number of points that are used to express the perimeter of either exterior or interior boundaries.



 TOC 

4.  GML Polygons

The GML encoding of a polygon defines a enclosed exterior boundary, with the first and last points of boundary being the same. Consider the example in Figure 6 (Hexagon and Associated GML).



    F--------------E
   /                \
  /                  \
 /                    \
A                      D
 \                    /
  \                  /
   \                /
    B--------------C

<gml:Polygon srsName="urn:ogc:def:crs:EPSG::4326">
  <gml:exterior>
    <gml:LinearRing>
      <gml:pos>43.311 -73.422</gml:pos> <!--A-->
      <gml:pos>43.111 -73.322</gml:pos> <!--B-->
      <gml:pos>43.111 -73.222</gml:pos> <!--C-->
      <gml:pos>43.311 -73.122</gml:pos> <!--D-->
      <gml:pos>43.411 -73.222</gml:pos> <!--E-->
      <gml:pos>43.411 -73.322</gml:pos> <!--F-->
      <gml:pos>43.311 -73.422</gml:pos> <!--A-->
    </gml:LinearRing>
  </gml:exterior>
</gml:Polygon>

 Figure 6: Hexagon and Associated GML 

Note that polygon vertices in Figure 6 (Hexagon and Associated GML) are expressed using <pos> elements for clarity. The vertices can also be expressed using a <posList> element.



 TOC 

5.  Holes in GML Polygons

A hole is specified in the polygon by defining an interior boundary. The points defining the internal boundary define the area represented by the hole in the primary (exterior) polygon. The shaded area in Figure 7 (Hexagon with Hole) is represented by the 4 points of the interior boundary specified by (w,z,y,x).



    F-------------E
   /               \
  / w-------------x \
 /  |/////////////|  \
A   |/////////////|   D
 \  |/////////////|  /
  \ z-------------y /
   \               /
    B-------------C

<gml:Polygon srsName="urn:ogc:def:crs:EPSG::4326">
  <gml:exterior>
    <gml:LinearRing>
      <gml:pos>43.311 -73.422</gml:pos> <!--A-->
      <gml:pos>43.111 -73.322</gml:pos> <!--B-->
      <gml:pos>43.111 -73.222</gml:pos> <!--C-->
      <gml:pos>43.311 -73.122</gml:pos> <!--D-->
      <gml:pos>43.511 -73.222</gml:pos> <!--E-->
      <gml:pos>43.511 -73.322</gml:pos> <!--F-->
      <gml:pos>43.311 -73.422</gml:pos> <!--A-->
    </gml:LinearRing>
  </gml:exterior>
  <gml:interior>
    <gml:LinearRing>
      <gml:pos>43.411 -73.322</gml:pos> <!--w-->
      <gml:pos>43.411 -73.222</gml:pos> <!--x-->
      <gml:pos>43.211 -73.222</gml:pos> <!--y-->
      <gml:pos>43.211 -73.322</gml:pos> <!--z-->
      <gml:pos>43.411 -73.322</gml:pos> <!--w-->
    </gml:LinearRing>
  </gml:interior>
</gml:Polygon>

 Figure 7: Hexagon with Hole 



 TOC 

6.  Service Boundary Specification and Selection Algorithm

A service boundary is represented by a polygon that may have many vertices. The enclosed area of the polygon represents the area in which a service, expressed as a service URN, maps to a single URI.

Figure 7 (Hexagon with Hole) is used to illustrate two service boundaries. The first service boundary A->F shall be referred to as area-A, and the second service boundary w->z shall be referred to as area-w. Furthermore, area-A is directly represented by the GML encoding provided in Figure 7 (Hexagon with Hole). Area-w is represented as a hole in area-A by the interior boundary. Since area-w is also a service boundary, a separate polygon describing this area is also required and is shown in Figure 8 (GML for Area-w) (note the reversal of the vertices).



<gml:Polygon srsName="urn:ogc:def:crs:EPSG::4326">
  <gml:exterior>
    <gml:LinearRing>
      <gml:pos>43.411 -73.322</gml:pos> <!--w-->
      <gml:pos>43.211 -73.322</gml:pos> <!--z-->
      <gml:pos>43.211 -73.222</gml:pos> <!--y-->
      <gml:pos>43.411 -73.222</gml:pos> <!--x-->
      <gml:pos>43.411 -73.322</gml:pos> <!--w-->
    </gml:LinearRing>
  </gml:exterior>
</gml:Polygon>

 Figure 8: GML for Area-w 

Service mappings for these boundaries might be provided by a LoST server in the form shown in Figure 9 (Service Boundary Specifications).



  <mapping xmlns="urn:ietf:params:xml:ns:lost1"
           expires="2010-12-25T09:44:33Z"
           lastUpdated="2010-03-08T03:48:22Z"
           source="authoritative.foo.example"
           sourceId="7e3f40b098c711dbb606011111111111">
    <displayName xml:lang="en">Outer Area Police</displayName>
    <service>urn:service:sos.police</service>
    <serviceBoundary profile="geodetic-2d">
      <gml:Polygon xmlns:gml="http://www.opengis.net/gml"
                   srsName="urn:ogc:def:crs:EPSG::4326">
        <gml:exterior>
          <gml:LinearRing>
            <gml:pos>43.311 -73.422</gml:pos>
            <gml:pos>43.111 -73.322</gml:pos>
            <gml:pos>43.111 -73.222</gml:pos>
            <gml:pos>43.311 -73.122</gml:pos>
            <gml:pos>43.511 -73.222</gml:pos>
            <gml:pos>43.511 -73.322</gml:pos>
            <gml:pos>43.311 -73.422</gml:pos>
          </gml:LinearRing>
        </gml:exterior>
        <!-- this is the service boundary hole -->
        <gml:interior>
          <gml:LinearRing>
            <gml:pos>43.411 -73.322</gml:pos>
            <gml:pos>43.211 -73.322</gml:pos>
            <gml:pos>43.211 -73.222</gml:pos>
            <gml:pos>43.411 -73.222</gml:pos>
            <gml:pos>43.411 -73.322</gml:pos>
          </gml:LinearRing>
        </gml:interior>
      </gml:Polygon>
    </serviceBoundary>
    <uri>sip:area-A-pd@example.com</uri>
    <uri>xmpp:area-A-pd@example.com</uri>
    <serviceNumber>000</serviceNumber>
  </mapping>

  <mapping xmlns="urn:ietf:params:xml:ns:lost1"
           expires="2010-12-25T09:44:33Z"
           lastUpdated="2010-03-08T03:48:22Z"
           source="authoritative.foo.example"
           sourceId="7e3f40b098c711dbb606011111111111">
    <displayName xml:lang="en">Inner Area Police</displayName>
    <service>urn:service:sos.police</service>
    <serviceBoundary profile="geodetic-2d">
      <gml:Polygon xmlns:gml="http://www.opengis.net/gml"
                   srsName="urn:ogc:def:crs:EPSG::4326">
        <gml:exterior>
          <gml:LinearRing>
            <gml:pos>43.411 -73.322</gml:pos>
            <gml:pos>43.211 -73.322</gml:pos>
            <gml:pos>43.211 -73.222</gml:pos>
            <gml:pos>43.411 -73.222</gml:pos>
            <gml:pos>43.411 -73.322</gml:pos>
          </gml:LinearRing>
        </gml:exterior>
      </gml:Polygon>
    </serviceBoundary>
    <uri>sip:area-w-pd@example.com</uri>
    <uri>xmpp:area-w-pd@example.com</uri>
    <serviceNumber>000</serviceNumber>
  </mapping>

 Figure 9: Service Boundary Specifications 

It is considered likely that LoST servers will need to provide responses sufficiently quickly to allow real-time queries to be performed as part of an emergency call routing flow. It is for this reason that databases supporting native geospatial query techniques are desirable and that service boundary specifications that are easily mapped to internal data structures are preferred. Using interior boundaries makes support for this operation easy, while allowing an arbitrary number of holes in a service boundary to be specified.

Each polygon is stored in the geospatial database and mapped to a service URN and destination URI. Many geospatial databases natively support polygons with interior exclusions. Without native support, interior boundaries can be stored against the polygon and can checked separately. A location falls within the area described by a polygon if it is within the exterior boundary and not within any interior boundary.

In the above example, if a location falls within the interior boundary, it maps to the "Inner Area Police" service; likewise, if a location falls within the exterior boundary, but not within the interior boundary, it maps to the "Outer Area Police" service.



 TOC 

7.  Security Considerations

Constraining the form of a polygon representation as described in this document does not introduce new security considerations.



 TOC 

8.  IANA Considerations

This document has no IANA actions.

[RFC Editor: please remove this section prior to publication.]



 TOC 

9.  Acknowledgements

Thanks to Carl Reed for input provided to the list some months back and for reviewing this document. Thanks to Michael Haberler for suggesting that such a specification is required. Thanks to Avery Penniston for review and feedback.



 TOC 

10.  References



 TOC 

10.1. Normative References

[RFC2119] Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” BCP 14, RFC 2119, March 1997 (TXT, HTML, XML).
[RFC5222] Hardie, T., Newton, A., Schulzrinne, H., and H. Tschofenig, “LoST: A Location-to-Service Translation Protocol,” RFC 5222, August 2008 (TXT).
[geoshape] Thomson, M. and C. Reed, “GML 3.1.1 PIDF-LO Shape Application Schema for use by the Internet Engineering Task Force (IETF),” Candidate OpenGIS Implementation Specification 06-142r1, Version: 1.0, April 2007.


 TOC 

10.2. Informative References

[I-D.ietf-ecrit-lost-sync] Schulzrinne, H. and H. Tschofenig, “Synchronizing Location-to-Service Translation (LoST) Protocol based Service Boundaries and Mapping Elements,” draft-ietf-ecrit-lost-sync-09 (work in progress), March 2010 (TXT).
[ISO-19107] ISO, “Geographic information - Spatial Schema,” ISO Standard 19107, First Edition, 5 2003.


 TOC 

Authors' Addresses

  James Winterbottom
  Andrew Corporation
  Andrew Building (39)
  Wollongong University Campus
  Northfields Avenue
  Wollongong, NSW 2522
  AU
Email:  james.winterbottom@andrew.com
  
  Martin Thomson
  Andrew Corporation
  Andrew Building (39)
  Wollongong University Campus
  Northfields Avenue
  Wollongong, NSW 2522
  AU
Email:  martin.thomson@andrew.com