GEOPRIV R. Barnes Internet-Draft M. Lepinski Updates: 3693, 3694 BBN Technologies (if approved) A. Cooper Intended status: BCP J. Morris Expires: November 28, 2010 Center for Democracy & Technology H. Tschofenig Nokia Siemens Networks H. Schulzrinne Columbia University May 27, 2010 An Architecture for Location and Location Privacy in Internet Applications draft-ietf-geopriv-arch-02 Abstract Location-based services (such as navigation applications, emergency services, management of equipment in the field) need geographic location information about Internet hosts, their users, and other related entities. These applications need to securely gather and transfer location information for location services, and at the same time protect the privacy of the individuals involved. This document describes an architecture for privacy-preserving location-based services in the Internet, focusing on authorization, security, and privacy requirements for the data formats and protocols used by these services. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on November 28, 2010. Barnes, et al. Expires November 28, 2010 [Page 1]
Internet-Draft Internet Location Architecture May 2010 Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Barnes, et al. Expires November 28, 2010 [Page 2]
Internet-Draft Internet Location Architecture May 2010 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. Binding Rules to Data . . . . . . . . . . . . . . . . . . 4 1.2. Location-Specific Privacy Risks . . . . . . . . . . . . . 5 1.3. Privacy Paradigms . . . . . . . . . . . . . . . . . . . . 6 2. Overview of the Architecture . . . . . . . . . . . . . . . . . 7 2.1. Basic Geopriv Scenario . . . . . . . . . . . . . . . . . . 8 2.2. Roles and Data Formats . . . . . . . . . . . . . . . . . . 9 3. The Location Life-Cycle . . . . . . . . . . . . . . . . . . . 12 3.1. Positioning . . . . . . . . . . . . . . . . . . . . . . . 13 3.1.1. Determination Mechanisms and Protocols . . . . . . . . 13 3.1.2. Privacy Considerations for Positioning . . . . . . . . 15 3.1.3. Security Considerations for Positioning . . . . . . . 16 3.2. Location Distribution . . . . . . . . . . . . . . . . . . 16 3.2.1. Privacy Rules . . . . . . . . . . . . . . . . . . . . 17 3.2.2. Location Configuration . . . . . . . . . . . . . . . . 19 3.2.3. Location References . . . . . . . . . . . . . . . . . 20 3.2.4. Privacy Considerations for Distribution . . . . . . . 20 3.2.5. Security Considerations for Distribution . . . . . . . 22 3.3. Location Use . . . . . . . . . . . . . . . . . . . . . . . 23 3.3.1. Privacy Considerations for Use . . . . . . . . . . . . 23 3.3.2. Security Considerations for Use . . . . . . . . . . . 23 4. Security Considerations . . . . . . . . . . . . . . . . . . . 24 5. Example Scenarios . . . . . . . . . . . . . . . . . . . . . . 26 5.1. Minimal Scenario . . . . . . . . . . . . . . . . . . . . . 26 5.2. Location-based Web Services . . . . . . . . . . . . . . . 27 5.3. Emergency Calling . . . . . . . . . . . . . . . . . . . . 29 5.4. Combination of Services . . . . . . . . . . . . . . . . . 31 6. Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 36 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 36 9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 36 9.1. Normative References . . . . . . . . . . . . . . . . . . . 36 9.2. Informative References . . . . . . . . . . . . . . . . . . 36 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 38 Barnes, et al. Expires November 28, 2010 [Page 3]
Internet-Draft Internet Location Architecture May 2010 1. Introduction Location-based services (applications that require information about the geographic location of an individual or device) are becoming increasingly common on the Internet. Navigation and direction services, emergency services, friend finders, management of equipment in the field and many other applications require geographic location information about Internet hosts, their users, and other related entities. As the accuracy of location information improves and the expense of calculating and obtaining it declines, the distribution and use of location information in Internet-based services will likely become increasingly pervasive. Ensuring that location information is transmitted and accessed in a secure and privacy- protective way is essential to the future success of these services, as well as the minimization of the privacy harms that could flow from their wide deployment and use. Standards for communicating location information over the Internet have an important role to play in providing a technical basis for privacy and security protection. This document describes a standardized privacy- and security-focused architecture for location- based services in the Internet: the Geopriv architecture. The central component of the Geopriv architecture is the location object, which is used to convey both location information about an individual or device and user-specified privacy rules governing that location information. As location information moves through its life cycle -- positioning, distribution, and use by its ultimate recipient(s) -- Geopriv provides mechanisms to secure the integrity and confidentiality of location objects and to ensure that location information is only transmitted in compliance with the user's privacy rules. The goals of this document are two-fold: First, the architecture described revises and expands on the basic Geopriv Requirements [2][3], in order to clarify how these privacy concerns and the Geopriv architecture apply to use cases that have arisen since the publication of those documents. Second, this document provides a general introduction to Geopriv and Internet location-based services, and is useful as a good first document for readers new to Geopriv. 1.1. Binding Rules to Data A central feature of the Geopriv architecture is that location information is always bound to privacy rules to ensure that entities that receive location are informed of how they may use it. These rules can convey simple directives ("do not share my location with others"), or more robust preferences ("allow my spouse to know my exact location all of the time, but only allow my boss to know it Barnes, et al. Expires November 28, 2010 [Page 4]
Internet-Draft Internet Location Architecture May 2010 during work hours"). By creating a structure to convey the user's preferences along with location information, the likelihood that those preferences will be honored necessarily increases. In particular, no recipient of the location information can disavow knowledge of users' preferences for how their location may be used. The binding of privacy rules to location information can convey users' desire for and expectations of privacy, which in turn helps to bolster social and legal systems' protection of those expectations. Binding of usage rules to sensitive information is a common way of protecting information. Several emerging schemes for expressing copyright information provide for rules to be transmitted together with copyrighted works. The Creative Commons [21] model is the most prominent example, allowing an owner of a work to set four types of rules ("Attribution," "Noncommercial," "No Derivative Works" and "ShareAlike") governing the subsequent use of the work. After the author sets these rules, the rules are conveyed together with the work itself, so that every recipient is aware of the copyright terms. Classification systems for controlling sensitive documents within an organization are another example. In these systems, when a document is created, it is marked with a classification such as "SECRET" or "PROPRIETARY." Each recipient of the document knows from this marking that the document should only be shared with other people who are authorized to access documents with that marking. Classification markings can also convey other sorts of rules, such as a specification for how long the marking is valid (a declassification date). The United States Department of Defense guidelines for classification [4] provides one example. 1.2. Location-Specific Privacy Risks While location-based services raise some privacy concerns that are common to all forms of personal information, many of them are heightened and others are uniquely applicable in the context of location information. Location information is frequently generated on or by mobile devices. Because individuals often carry their mobile devices with them, location data may be collected everywhere and at any time, often without user interaction, and it may potentially describe both what a person is doing and where he or she is doing it. For example, location data can reveal the fact that an individual was at a particular medical clinic at a particular time. The ubiquity of location information may also increase the risks of stalking and domestic violence if perpetrators are able to use (or abuse) location-based services to gain access to location information about their victims. Barnes, et al. Expires November 28, 2010 [Page 5]
Internet-Draft Internet Location Architecture May 2010 Location information is also of particular interest to governments and law enforcers around the world. The existence of detailed records of individuals' movements should not automatically facilitate the ability for governments to track their citizens, but in some jurisdictions, laws dictating what government agents must do to obtain location data are either non-existent or out-of-date. 1.3. Privacy Paradigms Traditionally, the extent to which data about individuals enjoys privacy protections on the Internet has largely been decided by the recipients of the data. Internet users may or may not be aware of the privacy practices of the entities with whom they share data. Even if they are aware, they have generally been limited to making a binary choice between sharing data with a particular entity or not sharing it. Internet users have not historically been granted the opportunity to express their own privacy preferences to the recipients of their data and to have those preferences honored. This paradigm is problematic because the interests of data recipients are often not aligned with the interests of data subjects. While both parties may agree that data should be collected, used, disclosed and retained as necessary to deliver a particular service to the data subject, they may not agree about how the data should otherwise be used. For example, an Internet user may gladly provide his email address on a Web site to receive a newsletter, but he may not want the Web site to share his email address with marketers, whereas the Web site may profit from such sharing. Neither providing the address for both purposes nor deciding not to provide it is an optimal option from the Internet user's perspective. The Geopriv model departs from this paradigm for privacy protection. As explained above, location information can be uniquely sensitive. And as siloed location-based services emerge and proliferate, they increasingly require standardized protocols for communicating location information between services and entities. Recognizing both of these dynamics, Geopriv gives data subjects the ability to express their choices with respect to their own location information, rather than allowing the recipients of the information to define how it will be used. The combination of heightened privacy risk and the need for standardization compelled the Geopriv designers to shift away from the prevailing Internet privacy model, instead empowering users to express their privacy preferences about the use of their location information. Geopriv does not, by itself, provide technical means through which it can be guaranteed that users' location privacy rules will be honored by recipients. The privacy protections in the Geopriv architecture Barnes, et al. Expires November 28, 2010 [Page 6]
Internet-Draft Internet Location Architecture May 2010 are largely provided by virtue of the fact that recipients of location are informed of relevant privacy rules, and are expected to only use location in accordance with those rules. The distributed nature of the architecture inherently limits the degree to which compliance can be guaranteed and verified by technical means. Section 4 describes how some security mechanisms can address this to a limited extent. By binding privacy rules to location information, however, Geopriv provides valuable information about users' privacy preferences, so that non-technical forces such as legal contracts, governmental consumer protection authorities, and marketplace feedback can better enforce those privacy preferences. If a commercial recipient of location information, for example, violates the location rules bound to the information, the recipient can in a growing number of countries be charged with violating consumer or data protection laws. In the absence of a binding of rules with location information, consumer protection authorities would be less able to protect consumers whose location information has been abused. 2. Overview of the Architecture This section provides an overview of the Geopriv architecture for the secure and private distribution of location information on the Internet. We describe the three phases of the "location life cycle" -- positioning, distribution and use -- and discuss how the components of the architecture fit within each phase. The next section provides additional detail about how each phase can be achieved in a private and secure manner. The risks discussed in the previous section all arise from unauthorized disclosure or usage of location information. Thus, the Geopriv architecture has two fundamental privacy goals: 1. Ensure that location information is distributed only to authorized entities, and 2. Provide information to those entities about how they are authorized to use the location information. If these two goals are met, all parties that receive location information will also receive directives about how they can use that information. Privacy-preserving entities will only engage in authorized uses, and entities that violate privacy will do so knowingly, since they have been informed of what is authorized (and thus, implicitly, of what is not). Barnes, et al. Expires November 28, 2010 [Page 7]
Internet-Draft Internet Location Architecture May 2010 Privacy rules and their distribution are thus the central technical components of the privacy system, since they inform location recipients about how they are authorized to use that information. The two goals in the preceding paragraph are enabled by two classes of rules: 1. Access control rules: Rules that describe which entities may receive location information and in what form 2. Usage rules: Rules that describe what uses of location information are authorized Within this framework for privacy, security mechanisms provide support for the application of privacy rules. For example, authentication mechanisms validate the identities of entities requesting location (so that authorization and access-control policies can be applied), and confidentiality mechanisms protect location information en route between privacy-preserving entities. Security mechanisms can also provide assurances that are outside the purview of privacy by, for example, assuring location recipients that location information has been faithfully transmitted to them by its creator. 2.1. Basic Geopriv Scenario As location information is transmitted among Internet hosts, it goes through a "location life-cycle": first, the location is computed based on some external information (positioning), then it is transmitted from one host to another (distribution) until finally it is used by a recipient (use). For example, suppose Alice is using a mobile device, she learns of her location from a wireless location service, and she wishes to share her location privately with her friends by way of a presence service. Alice clearly needs to provide the presence server with her location and rules about which friends can be provided with her location. To enable Alice's friends to preserve her privacy, they need to be provided with privacy rules. Alice may tell some of her friends the rules directly, or she can have the presence server provide the rules to her friends when it provides them with her location. In this way, every friend who receives Alice's location is authorized by Alice to receive it, and every friend who receives it knows the rules. Good friends will obey the rules. If a bad friend breaks them and Alice finds out, the bad friend cannot claim that he was unaware of the rules. Some of Alice's friends will be interested in using Alice's location only for their own purposes (to meet up with her or plot her location Barnes, et al. Expires November 28, 2010 [Page 8]
Internet-Draft Internet Location Architecture May 2010 over time, for example). The usage rules that they receive direct them as to what they can or cannot do (for example, Alice might not want them keeping her location for more than, say, two weeks). Consider one friend, Bob, who wants to send Alice's location to some of his friends. To operate in a privacy-protective way, Bob needs not only usage rules for himself, but also access control rules that describe who he can send information to and rules to give to the recipients. If the rules he received from the presence server authorize him to give Alice's location to others, he may do so; otherwise, he will require additional rules from Alice before he is authorized to distribute her location. If recipients who receive Alice's location from Bob want to distribute the location on further, they must go through the same process as Bob. The whole example is illustrated in the following figure: +----------+ | Wireless | | Location | | Service | Retrieve +----------+ Access Control Rules | +-----------------------------------+ | | +-----------------------------+ | Location | | Access | | | | | Control Rules v | | | | +-----+ | | | | | | | | | Bob |--> ... | | | +----->| | v v | | +-----+ +----------+ +----------+ | | |Device| |--Location->| Presence |--Location---->| +----------+ | -------- | | Server | |---->| Friend-1 | | |---Rules--->| |---Rules------>| +----------+ | Alice | +----------+ | +----------+ | | +----------+ +---->| Friend-2 | +----------+ Figure 1: Basic Geopriv Scenario 2.2. Roles and Data Formats The above example illustrates the six basic roles in the Geopriv architecture: Barnes, et al. Expires November 28, 2010 [Page 9]
Internet-Draft Internet Location Architecture May 2010 Target: An individual or other entity whose location is sought in the Geopriv architecture. In many cases the Target will be the human user of a Device, but it can also be an object such as a vehicle or shipping container to which a Device is attached. In some instances the Target will be the Device itself. The Target is the entity whose privacy Geopriv seeks to protect. Alice is the Target in Figure 1. Device: The technical device whose location is tracked as a proxy for the location of a Target. Alice's device is the Device in Figure 1. Rule Maker (RM): Performs the role of creating rules governing access to location information for a Target. In some cases the Target performs the Rule Maker role (as is the case with Alice), and in other cases they are separate. For example, a parent may serve as the Rule Maker when the Target is his child, or a corporate security officer may serve as the Rule Maker for devices owned by the corporation but used by employees. The Rule Maker is also not necessarily the owner of the Device. For example, a corporation may provide a Device to an employee but permit the employee to serve as the Rule Maker and set her own privacy rules. Location Generator (LG): Performs the roles of initially determining or gathering the location of the Device and providing it to Location Servers. Location Generators may be any sort of software or hardware used to obtain the Device's location (examples include GPS chips and cellular networks). A Device may even perform the Location Generator role for itself; Devices capable of unassisted satellite-based positioning and Devices that accept manually entered location information are two examples. The wireless location service plays the Location Generator role in Figure 1. Location Server (LS): Performs the roles of receiving location information and rules, applying the rules to the location information to determine what other entities, if any, can receive location information, and providing the location to Location Recpients. Location Servers receive location information from Location Generators and rules from Rule Makers, and then apply the rules to the location information. Location Servers may not necessarily be "servers" in the colloquial sense of hosts in remote data centers servicing requests. Rather, a Location Server can be any software or hardware component that distributes location information. Examples include a server in an access network, a presence server, or a Web browser or other software running on a Device. The above example includes three Location Servers: Alice, the presence service and Bob. Barnes, et al. Expires November 28, 2010 [Page 10]
Internet-Draft Internet Location Architecture May 2010 Location Recipient (LR): Performs the role of receiving location information. A Location Recipient may ask for location explicitly (by sending a query to a Location Server), or it may receive location asynchronously. The presence service, Bob, Friend-1 and Friend-2 are Location Recipients in Figure 1. In general, these roles may or may not be performed by physically separate entities, as demonstrated by the entities in Figure 1, many of which perform multiple roles. It is not uncommon for the same entity to perform both the LG and LS roles, or both the LR and LS roles. A single entity may take on multiple roles simply by virtue of its own capabilities and the permissions provided to it. Although in the above example there is only a single Location Generator and a single Rule Maker, in some cases a Location Server may receive Location Objects from multiple Location Generators or Rules from multiple Rule Makers. Likewise, a single Location Generator may publish location information to multiple Location Servers, and a single Location Recipient may receive Location Objects from multiple Location Servers. There is a close relationship between a Target and its Device. The term "Device" is used when discussing protocol interactions, whereas the term "Target" is used when discussing generically the person or object being located and its privacy. While in the example above there is a one-to-one relationship between the Target and the Device, Geopriv can also be used to convey location information about a device that is not directly linked to a single individual or object, such as a Device shared by multiple individuals. Two data formats are necessary within this architecture: Location Object (LO): An object used to convey location information together with Privacy Rules. Geopriv supports both geodetic location data (latitude/longitude/altitude/etc.) and civic location data (street/city/state/etc.). Either or both types of location information may be present in a single LO. Location Objects typically include some sort of identifier associated with the Target. Privacy Rule: A directive that regulates an entity's activities with respect to location information, including the collection, use, disclosure, and retention of the location information. Privacy Rules describe which entities may obtain location information in what form (access control rules) and how location information may be used by an entity (usage rules). Barnes, et al. Expires November 28, 2010 [Page 11]
Internet-Draft Internet Location Architecture May 2010 The whole example, using Geopriv roles and formats, is illustrated in the following figure: +----+ | LG | +----+ ^ | Positioning Data | | +------------Privacy Rules------------------>+----+ | | +---->| LR |--> ... | | | | LS | v | | +----+ +-------+ | |Target | +----+ | +----+ |Device |--------------->| LR |---------------+---->| LR | | RM | LO | LS | LO | +----+ | LS | +----+ | +-------+ | | +----+ +---->| LR | +----+ Figure 2: Basic Geopriv Scenario 3. The Location Life-Cycle The previous section gave an example of how an individual's location can be distributed through the Internet. In general, the location life-cycle breaks down into three phases: 1. Positioning: A Location Generator determines the Device's location. 2. Distribution: Location Servers send location to Location Recipients, which may in turn act as Location Servers and further distribute location to other Location Recipients (possibly several times). 3. Use: A Location Recipient receives the location and uses it. Each of these phases involves a different set of Geopriv roles and each has a different set of privacy and security implications. The Geopriv roles are mapped onto the location life-cycle in the figure below. Barnes, et al. Expires November 28, 2010 [Page 12]
Internet-Draft Internet Location Architecture May 2010 +----------+ +----------+ | | | Rule |+ | Device | | Maker(s)|| | | | || +----------+ +----------+| ^| +----------+ || Positioning | Rules || Data | || | |V V +----------+ +----------+ +----------+ |Location | Location | Location |+ LO |Location | |Generator |--------------->| Server(s)||-------------->|Recipient | | | | || | | +----------+ +----------+| +----------+ +----------+ <-------------------------><---------------------------><-----------> Positioning Distribution Use Figure 3: Location Life-Cycle 3.1. Positioning Positioning is the process by which the physical location of the Device is computed, based on some observations about the Device's situation in the physical world. (This process goes by several other names, including Location Determination or Sighting.) The input to the positioning process is some information about the Device, and the outcome is that the Location Generator knows the location of the Device. In this section, we give a brief taxonomy of current positioning systems, their requirements for protocol support, and the privacy and security requirements for positioning. 3.1.1. Determination Mechanisms and Protocols While the specific positioning mechanisms that can be applied for a given Device are strongly dependent on the physical situation and capabilities of the Device, these mechanisms generally fall into the three categories described in detail below: o Device-based o Network-based Barnes, et al. Expires November 28, 2010 [Page 13]
Internet-Draft Internet Location Architecture May 2010 o Network-assisted As suggested by the above names, a positioning scheme can rely on the Device, an Internet-accessible resource (not necessarily a network operator), or a combination of the two. For a given scheme, the nature of this reliance will dictate the protocol mechanisms needed to support it. With Device-based positioning mechanisms, the Device is capable of determining its location by itself. This is the case for manually- entered location or for (unassisted) satellite-based positioning (using a Global Navigation Satellite System, or GNSS). In these cases, the Device acts as its own Location Generator, and there are no protocols required to support positioning (since no information needs to be communicated). In network-based positioning schemes, an external Location Generator (an Internet host other than the Device) has access to sufficient information about the Device, through out-of-band channels, to establish the position of the Device. The most common examples of this type of LG are entities that have a physical relationship to the Device (such as ISPs). In wired networks, wiremap-based location is a network-based technique; in wireless networks, timing and signal- strength based techniques that use measurements from base stations are considered to be network-based. Large-scale IP-to-geo databases (for example, those based on WHOIS data or latency measurements) are also considered to be network-based positioning mechanisms. For network-based positioning as for Device-based, no protocols are strictly necessary to support positioning, since positioning information is collected outside of the location distribution system (at lower layers of the network stack, for example). This does not rule out the use of other Internet protocols (like SNMP) to collect inputs to the positioning process. Rather, since these inputs can only be used by certain Location Generators to determine location, they are not controlled as private information. Network-based positioning often provides location to protocols by which the network informs a Device of its own location (these are known as Location Configuration Protocols, see Section 3.2.2 for further discussion). Network-assisted systems account for the greatest number and diversity of positioning schemes. In these systems, the work of positioning is divided between the Device and an external Location Generator via some communication (possibly over the Internet), typically in one of two ways: o The Device provides measurements to the LG Barnes, et al. Expires November 28, 2010 [Page 14]
Internet-Draft Internet Location Architecture May 2010 o The LG provides assistance data to the Device "Measurements" are understood to be observations about the Device's environment, ranging from wireless signal strengths to the MAC address of a first-hop router. "Assistance" is the complement to measurement, namely the information that enables the computation of location based on measurements. A set of wireless base station locations (or wireless calibration information) would be an assistance datum, as would be a table that maps routers to buildings in a corporate campus. For example, wireless and wired networks can serve as the basis for network-assisted positioning. In several current 802.11 positioning systems, the Device sends measurements (e.g., MAC addresses and signal strengths) to a Location Generator, and the Location Generator returns a location to the client. In wired networks, the Device can send its MAC address to the Location Generator, which can query the MAC-layer infrastructure to determine the switch and port to which that MAC address is connected, then query a wire map to determine the location at which the wire connected to that port terminates. As an aside, the common phrase "assisted GPS" ("assisted GNSS" more broadly) actually encompasses techniques that transmit both measurements and assistance data. Systems in which the Device provides the Location Generator with GNSS measurements are measurement-based, while those in which the assistance server provide ephemeris or alamanac data are assistance-based in the above terminology. (Those familiar with GNSS positioning will note that there are of course cases in which both of these interactions occur within a single location determination protocol, so the categories are not mutually exclusive.) Naturally, the exchange of measurement or positioning data between the Device and the LG requires a protocol over which the information is carried. The structure of this protocol will depend on which of the two patterns a network-assisted scheme follows. Conversely, the structure of the protocol will determine which of the two parties (the Device, the LG, or both) is aware of the Device's location at the end of the protocol interaction. 3.1.2. Privacy Considerations for Positioning Positioning is the first point at which location may be associated with a particular Target's identity. Local identifiers, unlinked pseudonyms, or private identifiers that are not linked to the real identity of the Target should be used as forms of identity whenever possible. This provides privacy protection by disassociating the location from the Target's identity before it is distributed. Barnes, et al. Expires November 28, 2010 [Page 15]
Internet-Draft Internet Location Architecture May 2010 At the conclusion of the positioning process, the entity acting as the LG has the Device's location (if the Device is performing the LG role, then they both have it). If the entity acting as the LG also performs the role of LS, the privacy considerations in Section 3.2.4 apply. In some deployment scenarios, positioning functions and distribution functions may need to be provided by separate entities, in which case the LG and LS roles will not be performed by the same entity. In this situation, the LG acts as a "dumb," non-privacy-aware positioning resource, and the LS provides the privacy logic necessary to support distribution (possibly with multiple LSes using the same LG). In order to allow the privacy-unaware LG to distribute location to these LSes while maintaining privacy, the relationship between the LG and its set of LSes MUST be tightly constrained, effectively "hard-wired." That is, the LG MUST only provide location to a small fixed set of LSes, and each of these LSes MUST comply with the requirements of Section 3.2.4. 3.1.3. Security Considerations for Positioning Manipulation of the positioning process can expose location through two mechanisms: 1) A third party could guess or derive measurements about a specific device and use them to get the location of that Device. To mitigate this risk, the LG should be able to authenticate and authorize devices providing measurements and, if possible, verify that the presented measurements are likely to be the actual physical values measured by that client. These security procedures rely on the type of positioning being done, and may not be technically feasible in all cases. 2) By eavesdropping, a third party may be able to obtain measurements sent by the Device itself that indicate the rough position of the Device. To mitigate this risk, protocols used for positioning must provide confidentiality and integrity protections in order to prevent observation and modification of transmitted positioning data while en route between the Target and the LG. If a Location Generator or a Target chooses to act as a Location Server, it inherits the security requirements for an LS, described in Section 3.2.5. 3.2. Location Distribution When an entity receives location (from an LG or an LS) and redistributes it to other entities, it acts as a Location Server. Barnes, et al. Expires November 28, 2010 [Page 16]
Internet-Draft Internet Location Architecture May 2010 Location Distribution is the process by which one or more Location Servers provide LOs to Location Recipients in a privacy-preserving manner. The role of a Location Server is thus two-fold: First, it must collect location information and Rules that control access to that information. Rules can be communicated within a Location Object, within a protocol that carries LOs, or through a separate protocol that carries Rules. Second, the Location Server must process requests for location and apply the Rules to these requests in order to determine whether it is authorized to fulfill them by returning location information. A Location Server thus has at least two types of interactions with other hosts, namely receiving and sending Location Objects. An LS may optionally implement a third interaction, allowing Rule Makers to provision it with Rules. The distinction between these two cases is important in practice, because it determines whether the LS has a direct relationship with a Rule Maker: An LS that accepts Rules directly from a Rule Maker has such a relationship, while an LS that acquires all its Rules through LOs does not. 3.2.1. Privacy Rules Privacy Rules are the central mechanism in Geopriv for maintaining a Target's privacy, because they provide a recipient of a LO (an LS or LR) with information on how the LO may be used. Throughout the Geopriv architecture, Privacy Rules are communicated in rules languages with a defined syntax and semantics. For example, the Common Policy rules language has been defined [5] to provide a framework for broad-based rule specifications. Geopriv Policy [6] defines a language for creating location-specific rules. XCAP [7] can be used as a protocol to install rules in both of these formats. Privacy Rules follow a default-deny pattern: an empty set of Rules implies that all requests for location should be denied (other than requests made by the Target itself), with each Rule added to the set granting a specific permission. Adding a Rule to a set can never reduce existing permissions; it can only augment them. The following are examples of Privacy Rules governing location distribution: o Retransmit location when requested from example.com o Retransmit only city and country Barnes, et al. Expires November 28, 2010 [Page 17]
Internet-Draft Internet Location Architecture May 2010 o Retransmit location with no less than a 100 meter radius of uncertainty o Retransmit location only for the next two weeks Location Servers enforce Privacy Rules in two ways: by denying requests for location, or by transforming the location information before retransmitting it. Location Servers may also receive Rules governing location retention, such as "Retain location only for 48 hours." Such Rules are simply directives about how long the Target's location information can be retained. Privacy Rules can govern the behavior of both Location Servers and Location Recipients. Rules that direct Location Servers about how to treat a Target's location information are known as Local Rules. Local Rules are used internally by the Location Server to handle requests from Location Recipients. They are not distributed to Location Recipients. Forwarded Rules, on the other hand, travel inside LOs and direct Location Servers and Location Recipients about how to handle the location information they receive. Because the Rules themselves may reveal potentially sensitive information about the Target, only the minimal subset of Forwarded Rules necessary to handle the LO is distributed. An example can illustrate the interaction between Local Rules and Forwarded Rules. Suppose Alice provides the following Local Rules to a Location Server: o The LS may retransmit Alice's precise location to Bob, who in turn is permitted to retain the location information for one month o The LS may retransmit Alice's city, state, and country to Steve, who in turn is permitted to retain the location information for one hour o The LS may retransmit Alice's country to a photo-sharing website, which in turn is permitted to retain the location information for one year and retransmit it to any requesters When Steve asks for Alice's location, the Location Server can transmit to Steve the limited location information (city, state, and country) along with Forwarded Rules instructing Steve to (a) not further retransmit Alice's location information, and (b) only retain the location information for one hour. By only sending these Barnes, et al. Expires November 28, 2010 [Page 18]
Internet-Draft Internet Location Architecture May 2010 specifically applicable Forwarded Rules to Steve (as opposed to the full set of Local Rules), the LS is protecting Alice's privacy by not disclosing to Steve that (for example) Alice allows Bob to obtain more precise location information than Alice allows Steve to receive. Geopriv is designed to be usable even by devices with constrained processing capabilities. To ensure that Forwarded Rules can be processed on constrained devices, LOs are required to carry only a limited set of Forwarded Rules, with an option to reference a more robust set of external Rules. The limited Rule set covers two privacy aspects: how long the Target's location may be retained ("Retention"), and whether or not the Target's location may be retransmitted ("Retransmission"). A LO may contain a pointer to more robust Rules, such as those shown in the set of four Rules at the beginning of this section. 3.2.2. Location Configuration Some performing the Location Generator role are designed only to provide Targets with their own locations (as opposed to distributing a Target's location to others). The process of providing a Target with its own location is known within Geopriv as Location Configuration. The term Location Information Server (LIS) is often used to describe the entity that performs this function (although a LIS may also perform other functions, such as providing a Target's location to other entities). A Location Configuration Protocol (LCP) [8] is one mechanism that can be used by a Device to discover its own location from a LIS. LCPs provide functions in the way they obtain, transport and deliver location requests and responses between a LIS and a Device such that the LIS can trust that the location requests and responses handled via the LCP are in fact from/to the Target. Several LCPs have been developed within Geopriv [9][10][11][12]. A LIS whose sole purpose is to perform Location Configuration need only follow a simple privacy-preserving policy: transmit a Target's location only to the Target itself. This is known as the "LCP policy." Importantly, if an LS is also serving in the role of LG and it has not been provisioned with Privacy Rules for a particular Target, it MUST follow the LCP policy, whether it is a LIS or not. In the positioning phase, an entity serving the roles of both LG and LS that has not received Privacy Rules must follow this policy. The same is true for any LS in the distribution phase. Barnes, et al. Expires November 28, 2010 [Page 19]
Internet-Draft Internet Location Architecture May 2010 3.2.3. Location References The location distribution process occurs through a series of transmissions of Location Objects: transmissions of location "by value." Location "by value" can be expressed in terms of geodetic location data (latitude/longitude/altitude/etc.) and civic location data (street/city/state/etc.). Location can also be distributed "by reference," where a reference is represented by a URI that can be dereferenced to obtain the LO. This document summarizes the properties of location-by-reference that are discussed at length in [13]. Distribution of location by reference (distribution of location URIs) offer several benefits. Location URIs are a more compact way of transmitting location, since URIs are usually smaller than LOs. A recipient of location can make multiple requests to a URI over time to receive updated location (if the URI is configured to provide fresh location rather than a single "snapshot"). From a positioning perspective, location by reference can offer the additional benefit of "just in time" positioning. If location is distributed by reference, an entity acting as a combined LG/LS only needs to perform positioning operations when a recipient dereferences a previously distributed URI. From a privacy perspective, distributing location as a URI instead of as a Location Object can help protect privacy by forcing each recipient of the location to request location from the referenced LS, which can then apply access controls individually to each recipient. But the benefit provided here is contingent on the LS applying access controls. If the LS does not apply an access control policy to requests for a location URI (in other words, if it enforces the "possession model" defined in [13]), then transmitting a location URI presents the same privacy risks as transmitting the Location Object itself. Moreover, the use of location URIs without access controls can introduce additional privacy risks: If URIs predictable, an attacker to whom the URI has not been sent may be able to guess the URI and use it to obtain the referenced LO. To mitigate this, location URIs without access controls need to be constructed so that they contain a random component with sufficient entropy to make guessing infeasible. 3.2.4. Privacy Considerations for Distribution Location information MUST be accompanied by Rules throughout the distribution process. Otherwise, a recipient will not know what uses are authorized, and will not be able to use the LO. Consequently, Barnes, et al. Expires November 28, 2010 [Page 20]
Internet-Draft Internet Location Architecture May 2010 LOs MUST be able to express Rules that convey appropriate authorizations. An LS MUST only accept Rules from authorized Rule Makers. For an LS that receives Rules exclusively in LOs and has no direct relationship with a Rule Maker, this requirement is met by applying the Rules provided in a LO to the distribution of that LO. For an LS with a direct relationship to a Rule Maker, this requirement means that the LS MUST be configurable with an RM authorization policy. An LS SHOULD define a prescribed set of RMs that may provide Rules for a given Target or LO. For example, an LS may only allow the Target to set Rules for itself, or it might allow an RM to set Rules for several Targets (e.g., a parent for children, or a corporate security officer for employees). No matter how Rules are provided to an LS, for each LO it receives, it MUST combine all Rules that apply to the LO into a Rule set that defines which transmissions are authorized, and it MUST transmit location only in ways that are authorized by these Rules. An LS that receives Rules exclusively through LOs MUST examine the Rules that accompany a given LO in order to determine how the LS may use the LO (if any Rules are included by reference, the LS SHOULD attempt to download them). If the LO includes no Rules that allow the LS to transmit the LO to another entity, then the LS MUST NOT transmit the LO. If the LO contains no Rules at all (if it is in a format with no Rules syntax, for example), then the LS MUST delete it. An LS that receives Rules both directly from one or more Rule Makers and through LOs MUST combine the Rules in a given LO with Rules it has received from the RMs. The strategy the LS uses to combine these sets of Rules is a matter for local policy, depending on the relative priority that the LS grants to each source of Rules. Some example policies: Union: A transmission of location is authorized if it is authorized by either a rule in the LO or an RM-provided rule. Intersection: A transmission of location is authorized if it is authorized by both a rule in the LO and an RM-provided rule. RM Override: A transmission of location is authorized if it is authorized by an RM-provided rule (regardless of the LO Rules). Barnes, et al. Expires November 28, 2010 [Page 21]
Internet-Draft Internet Location Architecture May 2010 LO Override: A transmission of location is authorized if it is authorized by a LO-provided rule (regardless of the RM Rules). In general, it is RECOMMENDED that an LS follow the "Intersection" policy, since it grants equal weight to all RMs (including the LO creator). In cases where an external RM is more trusted than the source of the LO, the "RM Override" policy may be more suitable (for example, if the external RM is the Target, and the LO is provided by a third party). Conversely, the "LO Override" policy is best suited to cases where the LO provider is more trused than the RM (for example, if the RM is the user of a mobile device LS and the LO contains Rules from the RM's parents or corporate security office). 3.2.5. Security Considerations for Distribution An LS's decisions about how to transmit location are based on the identities of entities requesting information and other aspects of requests for location. In order to ensure that these decisions are made properly, the LS needs assurance of the reliability of information on the identities of the entities with which the LS interacts (including LRs, LSes, and RMs) and other information in the request. Protocols to convey LOs and protocols to convey Rules MUST provide information on the identity of the recipient of location and the identity of the RM, respectively. In order to ensure the validity of this information, these protocols MUST allow for mutual authentication of both parties, and MUST provide integrity protection for protocol messages. These security features ensure that the LG has sufficient information (and sufficiently reliable information) to make privacy decisions. As they travel through the Internet, Location Objects necessarily pass through a sequence of intermediaries, ranging from layer-2 switches to IP routers to application-layer proxies and gateways. The ability of an LS to protect privacy by making access control decisions is reduced if these intermediaries have access to a Location Object as it travels between privacy-preserving entities. Ideally, Location Objects should be transmitted with confidentiality protection end-to-end between an LS that transmits location and the LR that receives it. In some cases, the protocol conveying an LO provides confidentiality protection as a built-in security solution for its signaling (and potentially its data traffic). In this case, carrying an unprotected Location Object within such an encrypted channel is sufficient. Many protocols, however, are offering communication modes where messages are either unprotected or protected on a hop-by-hop basis (for example, between intermediaries Barnes, et al. Expires November 28, 2010 [Page 22]
Internet-Draft Internet Location Architecture May 2010 in a store-and-forward protocol). In such a case it is RECOMMENDED that the protocol allows for the use of encrypted LOs, or for the transmission of a reference to location in place of a LO [13]. 3.3. Location Use The primary privacy requirement of a Location Recipient is to constrain its usage of location to the set of uses authorized by the Rules in a LO. If an LR only uses a LO in ways that have minimal privacy impact -- specifically, if it does not transmit the LO to any other entity, and does not retain the LO for longer than is required to complete its interaction with the LS -- then no further action is necessary for the LR to comply with Geopriv requirements. As an example of this simplest case, if a Location Recipient (a) receives a location, (b) immediately provides to the Target information or a service based on the location, (c) does not retain the information, and (d) does not retransmit the location to any other entity, then the LR will comply with any set of Rules that are permissible under Geopriv. Thus, a service that, for example, only provides directions to the closest bookstore in response to an input of location, and promptly then discards the input location, will be in compliance with any Geopriv Rule set. LRs that make other uses of a LO (e.g., those that store LOs, or send them to other service providers to obtain location-based services) MUST meet the requirements below to assure that these uses are authorized. 3.3.1. Privacy Considerations for Use The principle privacy requirement for Location Recipients is to follow usage rules. When an LR receives a LO, it is REQUIRED to examine the Rules included with that LO. Any usage the LR makes of the LO MUST be explicitly authorized by these Rules. Since Rules are positive grants of permission, any action not explicitly authorized is denied by default. 3.3.2. Security Considerations for Use Since the Location Recipient role does not involve transmission of location, there are no protocol security considerations required to support privacy (other than ensuring that data does not leak unintentionally caused by security breaches). Aside from privacy, Location Recipients often require some assurance that a LO is reliable (assurance of the integrity, authenticity, and validity of an LO), since LRs use LOs in order to deliver location- Barnes, et al. Expires November 28, 2010 [Page 23]
Internet-Draft Internet Location Architecture May 2010 based services. Threats against this reliability and corresponding mitigations are discussed in the Security Considerations below. 4. Security Considerations Security considerations related to the privacy of Location Objects are discussed throughout this document. In this section we summarize those concerns and consider security risks not related to privacy. The life-cycle of a Location Object often consists of a series of location transmissions. Protocols that carry location can provide strong assurances, but only for a single segment of the Location Object's life cycle. In particular, a protocol can provide integrity protection and confidentiality for the data exchanged, and mutual authentication of the parties involved in the protocol, by using a secure transport such as IPsec or TLS. Additionally, if (1) the protocol provides mutual authentication for every segment, and (2) every entity in the location distribution chain exchanges information only with entities with whom it has a trust relationship, entities can transitively obtain assurances regarding the origin and ultimate destination of the Location Object. Of course, direct assurances are always preferred over assurances requiring transitive trust, since they require fewer assumptions. Using protocol mechanisms alone, the entities can receive assurances only about a single hop in the distribution chain. For example, suppose that an LR receives location from an LS over an integrity- and confidentiality-protected channel. The LR knows that the transmitted LO has not been modified or observed en route. However, the assurances provided by the protocol do not guarantee that the transmitted LO was not corrupted before it was sent to the LS (by a previous LS, for example). Likewise, the LR can verify that the LO was transmitted by the LS, but cannot verify the origin of the LO if it did not originate with the LS. Security mechanisms in protocols are thus unable to provide direct assurances over multiple transmissions of a LO. However, the transmission of location "by reference" can be used to effectively turn multi-hop paths into single-hop paths. If the multiple transmissions of a LO are replaced by multiple transmissions of a URI (a multi-hop dissemination channel), the LO need only traverse a single hop, namely the dereference transaction between the LR and the dereference server. The major threats to the security of Location Objects can be grouped into two categories. First, threats against the integrity and Barnes, et al. Expires November 28, 2010 [Page 24]
Internet-Draft Internet Location Architecture May 2010 authenticity of Location Objects can expose entities that rely on Location Objects. Second, threats against the confidentiality of Location Objects can allow unauthorized access to location information. A Location Object contains four essential types of information: identifiers for the described Target, location information, time- stamps, and Rules. By grouping values of these various types together within a single structure, a Location Object encodes a set of bindings among them. That is, the Location Object asserts that the identified Target was present at the given location at the given time and that the given Rules express the Target's desired policy at that time for the distribution of his location. Below, we provide a description of the assurances required by each party involved in the location distribution in order to mitigate the possible attacks on these bindings. Rule Maker: The Rule Maker is responsible for creating the Target's Privacy Rules and for uploading them to the location servers. The primary assurance required by the Rule Maker is that the Target's Privacy Rules are correctly associated with the Target's identity when they are conveyed to each location server that handles the Location Object. Ensuring the integrity of the Privacy Rules distributed to the location servers prevents rule-tampering attacks. In many circumstances, the privacy policy of the Target may itself be sensitive information; in these cases, the Rule Maker also requires the assurance that the binding between the Target's identity and the Target's Privacy Rules are not deducible by anyone other than an authorized Location Server. Location Server: The Location Server is responsible for enforcing the Target's Privacy Rules. The first assurance required by the Location Server is that the binding between the Target's Privacy Rules and the Target's identity is authentic. Authenticating and authorizing the Rule Maker who creates, updates and deletes the Privacy Rules prevents rule-tampering attacks. The Location Server has to ensure that the authorization policies are not exposed to third parties, if so desired by the Rule Maker (when the rules themselves are privacy-sensitive). Location Recipient: The Location Recipient is the consumer of the Location Object. The Location Recipient thus requires assurances about the authenticity of the bindings between the Target's location, the Target's identity and the time. Ensuring the authenticity of these bindings helps to prevent various attacks, such falsifying the location, modifying the time-stamp, faking the identity, replaying location objects. Barnes, et al. Expires November 28, 2010 [Page 25]
Internet-Draft Internet Location Architecture May 2010 Location Generator: The primary assurance required by the Location Generator is that the Location Server to which the Location Object is initially published is one that is trusted to enforce the Target's Privacy Rules. Authenticating the trusted Location Server mitigates the risk of server impersonation attacks. Additionally, the Location Generator is responsible for the location determination process, which is also security sensible as wrong input provided by external entites can lead to undesireable disclosure or access to location information information. Assurances as to the integrity and confidentiality of a Location Object can be provided directly through the Location Object format. RFC 4119 provides a description for usage of S/MIME to integrity and confidentility protection. Although such direct, end-to-end assurances are desirable, and these mechanisms should be used whenever possible, there are many deployment scenarios where directly securing a Location Object is impractical. For example, in some deployment scenarios a direct trust relationship may not exist between the creator of the Location Object and the recipient. Additionally, in a scenario where many recipients are authorized to receive a given Location Object, the creator of the Location Object cannot guarantee end-to-end confidentiality without knowing precisely which recipient will receive the Location Object. Many of these cases can, however, be addressed by the usage of a Location-by- Reference (possibly combined with a location object). 5. Example Scenarios This section contains a set of example of how the Geopriv architecture can be deployed in practice. These examples are meant to illustrate key points of the architecture, rather than to form an exhaustive set of use cases. For convenience and clarity in these examples, we assume that the Privacy Rules that a LO carries are equivalent to those in a PIDF-LO Location Object (namely, that the principal Rules that can be set are limits on the retransmission and retention of the LO). While these two Rules are the most well-known and important examples, the specific types of Rules an LS or LR must consider will in general depend on the types of LO it processes. 5.1. Minimal Scenario One of the simplest scenarios in the Geopriv architecture is when a Device determines its own location and uses that LO to request a service (e.g., by including the LO in an HTTP POST request or SIP INVITE message), and the server delivers that service immediately Barnes, et al. Expires November 28, 2010 [Page 26]
Internet-Draft Internet Location Architecture May 2010 (e.g., in a 200 OK response in HTTP or SIP), without retaining or retransmitting the Device's location. The Device acts as an LG by using a Device-based positioning algorithm (e.g., manual entry) and as a Location Server by interpreting the rule and transmitting the LO. The Target acts as a Rule Maker by specifying that the location should be sent to the server. The server acts as a Location Recipient by receiving and using the LO. In this case, the privacy of location information is maintained in two steps: The first step is that location is only transmitted as directed by the single Rule Maker, namely the Target. The second step is simply the fact that the server, as LR, does not do anything that creates a privacy risk -- it does not retain or retransmit location. Because the server limits its behavior in this way, it does not need to read the Rules in the LO (even though they were provided) -- no Rule would prevent it from using location in this safe manner. The following outline summarizes this scenario: o Positioning: Device-based, Device=LG o Distribution hop 1: HTTP UA --> Ephemeral web service, privacy via user indication o Use: Ephemeral web service delivers response without retaining or retransmitting location o Key points: * LRs that do not behave in ways that risk privacy are Geopriv- compliant by default. No further action is necessary. 5.2. Location-based Web Services Many location-based services are delivered over the Web, using Javascript code to orchestrate a series of HTTP requests for location specific information. To support these applications, browser extensions have been developed that support Device-based positioning (manual entry and GPS) and network-assisted positioning (via AGPS, and multilateration with 802.11 and cellular signals), exposing position to web pages through Javascript APIs. In this scenario, we consider a Target that uses a browser with a network-assisted positioning extension. When the Target uses this browser to request location-based services from a web page, the browser prompts the user to grant the page permission to access the user's location. If the user grants permission, the browser Barnes, et al. Expires November 28, 2010 [Page 27]
Internet-Draft Internet Location Architecture May 2010 extension sends 802.11 signal strength measurements to a positioning server, which then returns the position of the host. The extension constructs a Location Object with this location and Rules set by the user, then passes the LO to the page through its Javascript API. The page then obtains location-relevant information using an XMLHttpRequest [14] to a server in the same domain as the page and renders this information to the user. At first blush, this scenario seems much more complicated than the minimal scenario above. However, most of the privacy considerations are actually the same. The positioning phase in this scenario begins when the browser extension contacts the positioning server. The positioning server acts as a Location Generator. The distribution phase actually occurs entirely within the Target host. This phase begins when the positioning server, now acting as LS, follows the LCP policy by providing location only to the Target. The next hop in distribution occurs when the browser extension (an entity under the control of the Target) passes a LO to the web page (an entity under the control of its author). In this phase, the browser extension acts as an LS, with the Target as the sole Rule Maker; the user interface for rule-making is effectively a protocol for conveying Rules, and the extension's API effectively defines a a way to communicate LOs and a LO Format. The web site acts as Location Recipient when the web page accepts the LO. The use phase encompasses the web site's use of the LO. In this context, the phrase "web site" encompasses not only the web page, but also the dedicated supporting logic behind it. Considering the entire web site as a recipient, rather than a single page, it becomes clear that sending the LO in an XMLHttpRequest to a back-end server is like passing it to a separate component of the LR (as opposed to retransmitting it to another entity). Thus, even in this case, where location-relevant information is obtained from a back-end server, the LR does not retain or retransmit location, so its behavior is "privacy-safe" -- it doesn't need to interpret the Rules in the LO. However, consider a variation on this scenario where the web page requests additional information (a map, for instance) from a third- party site. In this case, since location is being transmitted to a third party, the web site (either in the web page or in a back-end server) would need to verify that this transmission is allowed by the LO's Privacy Rules. Similarly, if the site wanted to log the user's location information, then it would need to examine the LO to determine how long this information can be retained. In such a case, if the LR needs to do something that is not allowed by the Rules, it Barnes, et al. Expires November 28, 2010 [Page 28]
Internet-Draft Internet Location Architecture May 2010 may have to deny service to the user (hopefully providing a message with the reason). Nonetheless, if the Rules permit retention or retransmission (even if this retransmission is limited by access control rules), then the LR may do so to the extent the Rules allow. The following outline summarizes this scenario: o Positioning: Network-assisted, positioning server=LG o Rule installation: RM (=Target) gives permission to sites and sets LO Rules o Distribution hop 1: positioning server=LS --> Target, privacy via LCP policy o Distribution hop 2: Browser=LS --> Web site=LR, privacy via user confirmation o Use: Back-end server delivers location-relevant information without further retransmission, then deletes location; privacy via safe behavior o Key points: * Privacy in this scenario is provided by a combination of explicit user direction and Rules in an LO * Distribution can occur within a host, between mutually untrusting components * Some transmissions of location are actually internal to an LR * LRs that do things that might be constrained by Rules need to verify that these actions are allowed for a particular LO 5.3. Emergency Calling Support for emergency calls by Voice-over-IP devices is a critical use case for location information about Internet hosts. The details of the Internet architecture for emergency calling are described in [15][16]. In this architecture, there are three critical steps in the placement of an emergency call, each involving location information: 1. Determine the location of the caller 2. Determine the proper Public Safety Answering Point (PSAP) for the caller's location Barnes, et al. Expires November 28, 2010 [Page 29]
Internet-Draft Internet Location Architecture May 2010 3. Send a SIP INVITE message (including the caller's location) to the PSAP The first step in an emergency call is to determine the location of the caller. This step is the positioning phase of the location life- cycle. Location is determined by whatever means are available to the caller's device, or to the network, if this step is being done by a proxy. Whichever entity does the positioning (either the caller or a proxy) acts as an Location Server, preserving the privacy of location information by only including it in emergency calls. The second step in an emergency call encompasses location distribution and use. The entity that is routing the emergency call sends location though the LoST protocol [17] to a mapping server. In this role, the routing entity acts as a Location Server and the LoST server acts as a Location Recipient. The LO format within LoST does not allow Rules to be sent along with location, but because LoST is an application-specific protocol, the sending of location within a LoST message authorizes the LoST server to use the location to complete the protocol, namely to route the message as necessary through the LoST mapping architecture [18]. That is, the LoST server is authorized to complete the LoST protocol, but to do nothing else. The third step in an emergency call is again a combination of distribution and use. The caller (or another entity that inserts the caller's location) acts as an LS and the PSAP acts as a Location Recipient. In this specific example, the caller's location is transmitted either as a PIDF-LO object or as a reference that returns a PIDF-LO (or both); in the latter case, the reference should be appropriately protected so that only the PSAP has access. In any case, the receipt of a LO implies that the PSAP should obey the Rules in those LOs in order to preserve privacy. Depending on the regulatory environment, the PSAP may have the option to ignore those constraints in order to respond to an emergency, or it may be bound to respect these Rules (in spite of the emergency situation). The following outline summarizes this scenario: o Positioning: Any o Distribution/use hop 1: Target=LS --> LoST infrastructure (no Rules), privacy via authorization implicit in protocol o Distribution/use hop 2: Target=LS --> PSAP, privacy via Rules in LO o Use: PSAP uses location to deliver emergency services Barnes, et al. Expires November 28, 2010 [Page 30]
Internet-Draft Internet Location Architecture May 2010 o Key points: * Privacy in this scenario is provided by a combination of explicit user direction, implicit authorization particular to a protocol, and Rules in an LO * LRs may be constrained to respect or ignore Privacy Rules by local regulation 5.4. Combination of Services In modern Internet applications, users frequently receive information via one channel and broadcast it via another. In this sense, both users and channels (e.g., web services) become location servers. Here we consider a more complex example that illustrates this pattern across multiple logical hops. Suppose Alice (the Target) subscribes to a wireless ISP that determines her location using a network-based positioning technique (e.g., via the location of the base station serving the Target), and provides that information directly to a location-enhanced presence provider (which might use SIP, XMPP, or another protocol). The location-enhanced presence provider allows Alice to specify Rules for how this location is distributed: which friends should receive Alice's location and what Rules they should get with it. Alice uses a few other location-enhanced services as well, so she sends Rules that allow her location to be shared with those services, and allow those services to retain and retransmit her location. Bob is one of Alice's friends, and he receives her location via this location-enhanced presence service. Noting that she's at their favorite coffee shop, Bob wants to upload a photo of the two of them at the coffee shop to a photo-sharing site, along with a LO that marks the location. Bob checks the Rules in Alice's LO and verifies that the photo sharing site is one of the services that Alice authorized. Seeing that Alice has authorized him to give the LO to the photo-sharing site, he attaches it to the photo and uploads it. Once the geo-tagged photo is uploaded, the photo sharing site reads the Rules in the LO and verifies that the site is authorized to store the photo and to share it with others. Since Alice has allowed the site to retransmit and retain without any constraints, the site fulfills Bob's request to make the geo-tagged photo publicly accessible. Eve, another user of the photo sharing site, downloads the photo of Alice and Bob at the coffee shop and receives Alice's LO along with it. Eve posts the photo and location to her public page on a social Barnes, et al. Expires November 28, 2010 [Page 31]
Internet-Draft Internet Location Architecture May 2010 networking site without checking the Rules, even though the LO doesn't allow Eve to send the location anywhere else. The social networking site, however, observes that no retransmission or retention are allowed (both of which it needs for a public posting), and rejects the upload. In terms of the location life-cycle, this scenario consists of a positioning step, followed by four distribution hops and use. Positioning is the simplest step: An LG in Alice's ISP monitors her location and transmits it to the presence service, maintaining privacy by only transmitting location to a single entity (to which Alice has delegated privacy responsibilities). The first distribution hop occurs when the presence server sends location to Bob. In this transaction, the presence server acts as an LS, Alice acts as an RM, and Bob acts as an LR. The privacy of this transaction is assured by the fact that Alice has installed Rules on the presence server that dictate who it may allow to access her location. The second distribution hop is when Bob uploads the LO to the photo-sharing site. Here Bob acts as an LS, preserving the privacy of location information by verifying that the Rules in the LO allow him to upload it. The third distribution hop is when the photo-sharing site sends the LO to Eve, likewise following the Rules -- but a different set of Rules than Bob, since a LO can specify different Rule sets for different Location Servers. Eve is the fourth LS in the chain, and fails to comply with Geopriv by not checking the Rules in the LO prior to uploading the LO to the social networking site. The site, however, is a responsible LR -- it checks the Rules in the LO, sees that they don't allow it to use the location as it needs to, and discards the LO. The following outline summarizes this scenario: o Positioning: Network-based, LG in network, privacy via exclusive relationship with presence service o Distribution/use hop 1: Presence server --> Bob, privacy via Alice's access control rules o Distribution/use hop 2: Bob --> photo sharing site, privacy via Rules for Bob in LO o Distribution/use hop 3: Photo sharing site --> Eve, privacy via Rules for site in LO o Distribution/use hop 4: Eve --> Social networking site, violates privacy by retransmitting Barnes, et al. Expires November 28, 2010 [Page 32]
Internet-Draft Internet Location Architecture May 2010 o Use: Social networking site, privacy via checking Rules and discarding o Key points: * Privacy can be preserved through multiple hops * A LO can specify different Rules for different entities * An LS can still disobey the Rules, but even then, the architecture still works in some cases 6. Glossary The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [1]. $ Access Control Rule A rule that describe which entities may receive location information and in what form. $ civic location The geographic position of an entity in terms of a postal address or civic landmark. Examples of such data are room number, street number, street name, city, ZIP code, county, state and country. $ Device The technical device whose location is tracked as a proxy for the location of a Target. $ geodetic location The geographic position of an entity in a particular coordinate system (for example, a latitude-longitude pair). $ Local Rule A Privacy Rules that directs a Location Server about how to treat a Target's location information. Local Rules are used internally by a Location Server to handle requests from Location Recipients. They are not distributed to Location Recipients. Barnes, et al. Expires November 28, 2010 [Page 33]
Internet-Draft Internet Location Architecture May 2010 $ Location Generator (LG) Performs the role of initially determining or gathering the location of a Target. Location Generators may be any sort of software or hardware used to obtain a Target's location (examples include GPS chips and cellular networks). $ Location Information Server (LIS) An entity responsible for providing devices within an access network with information about their own locations. A Location Information Server uses knowledge of the access network and its physical topology to generate and distribute location information to devices. $ Location Object (LO) A data unit that conveys location information together with Privacy Rules within the Geopriv architecture. A Location Object may convey geodetic location data (latitiude/longitude/altitude), civic location data (street/city/state/etc.), or both. $ Location Recipient (LR) An ultimate end point entity to which a Location Object is distributed. Location Recipients request location information about a particular Target from a Location Server. If allowed by the appropriate Privacy Rules, a Location Recipient will receive Location Objects describing the Target's location from the Location Server. $ Location Server (LS) An entity that receives Location Objects from Location Generators, Privacy Rules from Rule Makers, and location requests from Location Recipients. A Location Server applies the appropriate Privacy Rules to a Location Object received from a Location Generator and may disclose the Location Object, in compliance with the Rules, to Location Recipients. Location Servers may not necessarily be "servers" in the colloquial sense of hosts in remote data centers servicing requests. Rather, a Location Server can be any software or hardware component that receives and distributes location information. Examples include a positioning server (with a location interface) in an access network, a presence server, or a Web browser or other software running on a Target's device. Barnes, et al. Expires November 28, 2010 [Page 34]
Internet-Draft Internet Location Architecture May 2010 $ Privacy Rule A directive that regulates an entity's activities with respect to a Target's location information, including the collection, use, disclosure, and retention of the location information. Privacy Rules describe how location information may be used by an entity, the level of detail with which location information may be described to an entity, and the conditions under which location information may be disclosed to an entity. Privacy Rules are communicated from Rule Makers to Location Servers and conveyed in Location Objects throughout the Geopriv architecture. $ Rule See Privacy Rule. $ Rule Maker (RM) An individual or entity that is authorized to set Privacy Rules for a Target. In some cases a Rule Maker and a Target will be the same individual or entity, and in other cases they will be separate. For example, a parent may serve as the Rule Maker when the Target is his child. The Rule Maker is also not necessarily the owner of a Target device. For example, a corporation may own a device that it provides to an employee but permit the employee to serve as the Rule Maker and set her own Privacy Rules. Rule Makers provide the Privacy Rules associated with a Target to Location Servers. $ Forwarded Rule A Privacy Rule that travels inside a Location Object. Forwarded Rules direct Location Recipients about how to handle the location information they receive. Because the Forwarded Rules themselves may reveal potentially sensitive information about a Target, only the minimal subset of Forwarded Rules necessary for a Location Recipient to handle a Location Object is distributed to the Location Recipient. $ Target An individual or other entity whose location is sought in the Geopriv architecture. In many cases the Target will be the human user of a Device, or it may be an object such as a vehicle or shipping container to which a Device is attached. In some instances the Target will be the Device itself. The Target is the entity whose privacy Geopriv seeks to protect. Barnes, et al. Expires November 28, 2010 [Page 35]
Internet-Draft Internet Location Architecture May 2010 $ Usage Rule A rule that describe what uses of location information are authorized. 7. Acknowledgements Section 4 is largely based on the security investigations conducted as part of the Geopriv Layer-7 Location Configuration Protocol design team, which produced [8]. We would like to thank all the members of the design team. We would also like to thank Marc Linsner and Martin Thomson for their contributions regarding terminology and LCPs. 8. IANA Considerations This document makes no request of IANA. 9. References 9.1. Normative References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. 9.2. Informative References [2] Cuellar, J., Morris, J., Mulligan, D., Peterson, J., and J. Polk, "Geopriv Requirements", RFC 3693, February 2004. [3] Danley, M., Mulligan, D., Morris, J., and J. Peterson, "Threat Analysis of the Geopriv Protocol", RFC 3694, February 2004. [4] U.S. Department of Defense, "National Industrial Security Program Operating Manual", DoD 5220-22M, January 1995. [5] Schulzrinne, H., Tschofenig, H., Morris, J., Cuellar, J., Polk, J., and J. Rosenberg, "Common Policy: A Document Format for Expressing Privacy Preferences", RFC 4745, February 2007. [6] Schulzrinne, H., Tschofenig, H., Morris, J., Cuellar, J., and J. Polk, "Geolocation Policy: A Document Format for Expressing Privacy Preferences for Location Information", draft-ietf-geopriv-policy-21 (work in progress), January 2010. Barnes, et al. Expires November 28, 2010 [Page 36]
Internet-Draft Internet Location Architecture May 2010 [7] Rosenberg, J., "The Extensible Markup Language (XML) Configuration Access Protocol (XCAP)", RFC 4825, May 2007. [8] Tschofenig, H. and H. Schulzrinne, "GEOPRIV Layer 7 Location Configuration Protocol; Problem Statement and Requirements", draft-ietf-geopriv-l7-lcp-ps-10 (work in progress), July 2009. [9] Polk, J., Schnizlein, J., and M. Linsner, "Dynamic Host Configuration Protocol Option for Coordinate-based Location Configuration Information", RFC 3825, July 2004. [10] Schulzrinne, H., "Dynamic Host Configuration Protocol (DHCPv4 and DHCPv6) Option for Civic Addresses Configuration Information", RFC 4776, November 2006. [11] Polk, J., "Dynamic Host Configuration Protocol (DHCP) IPv4 and IPv6 Option for a Location Uniform Resource Identifier (URI)", draft-ietf-geopriv-dhcp-lbyr-uri-option-07 (work in progress), March 2010. [12] Barnes, M., Winterbottom, J., Thomson, M., and B. Stark, "HTTP Enabled Location Delivery (HELD)", draft-ietf-geopriv-http-location-delivery-16 (work in progress), August 2009. [13] Marshall, R., "Requirements for a Location-by-Reference Mechanism", draft-ietf-geopriv-lbyr-requirements-09 (work in progress), November 2009. [14] World Wide Web Consortium, "The XMLHttpRequest Object", W3C document http://www.w3.org/TR/XMLHttpRequest/, April 2008. [15] Rosen, B., Schulzrinne, H., Polk, J., and A. Newton, "Framework for Emergency Calling using Internet Multimedia", draft-ietf-ecrit-framework-10 (work in progress), July 2009. [16] Rosen, B. and J. Polk, "Best Current Practice for Communications Services in support of Emergency Calling", draft-ietf-ecrit-phonebcp-14 (work in progress), January 2010. [17] Hardie, T., Newton, A., Schulzrinne, H., and H. Tschofenig, "LoST: A Location-to-Service Translation Protocol", RFC 5222, August 2008. [18] Schulzrinne, H., "Location-to-URL Mapping Architecture and Framework", draft-ietf-ecrit-mapping-arch-04 (work in progress), March 2009. Barnes, et al. Expires November 28, 2010 [Page 37]
Internet-Draft Internet Location Architecture May 2010 [19] Peterson, J., "A Presence-based GEOPRIV Location Object Format", RFC 4119, December 2005. [20] Polk, J. and B. Rosen, "Location Conveyance for the Session Initiation Protocol", draft-ietf-sip-location-conveyance-13 (work in progress), March 2009. URIs [21] <http://creativecommons.org/> Authors' Addresses Richard Barnes BBN Technologies 9861 Broken Land Pkwy, Suite 400 Columbia, MD 21046 USA Phone: +1 410 290 6169 Email: rbarnes@bbn.com Matt Lepinski BBN Technologies 10 Moulton St Cambridge, MA 02138 USA Phone: +1 617 873 5939 Email: mlepinski@bbn.com Alissa Cooper Center for Democracy & Technology 1634 I Street NW, Suite 1100 Washington, DC USA Email: acooper@cdt.org Barnes, et al. Expires November 28, 2010 [Page 38]
Internet-Draft Internet Location Architecture May 2010 John Morris Center for Democracy & Technology 1634 I Street NW, Suite 1100 Washington, DC USA Email: jmorris@cdt.org Hannes Tschofenig Nokia Siemens Networks Linnoitustie 6 Espoo 02600 Finland Phone: +358 (50) 4871445 Email: Hannes.Tschofenig@gmx.net URI: http://www.tschofenig.priv.at Henning Schulzrinne Columbia University Department of Computer Science 450 Computer Science Building New York, NY 10027 US Phone: +1 212 939 7004 Email: hgs@cs.columbia.edu URI: http://www.cs.columbia.edu Barnes, et al. Expires November 28, 2010 [Page 39]
