Hub MIB Working Group J. Flick
INTERNET DRAFT Hewlett-Packard Company
J. Johnson
RedBack Networks
August 1998
Definitions of Managed Objects for
the Ethernet-like Interface Types
<draft-ietf-hubmib-etherif-mib-v2-00.txt>
Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference
material or to cite them other than as "work in progress."
To view the entire list of current Internet-Drafts, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern
Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific
Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast).
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
This memo obsoletes RFC 2358 ''Definitions of Managed Objects for the
Ethernet-like Interface Types''. This memo extends that
specification by including management information useful for the
management of 1000 Mb/s and full-duplex Ethernet interfaces.
Ethernet technology, as defined by the 802.3 Working Group of the
IEEE, continues to evolve, with scalable increases in speed, new
types of cabling and interfaces, and new features. This evolution
may require changes in the managed objects in order to reflect this
new functionality. This document, as with other documents issued by
Flick, et. al. Expires February 1999 [Page 1]
Internet Draft Ethernet-Like MIB August 1998
this working group, reflect a certain stage in the evolution of
Ethernet technology. In the future, this document might be revised,
or new documents might be issued by the Ethernet Interfaces and Hub
MIB Working Group, in order to reflect the evolution of Ethernet
technology.
Distribution of this memo is unlimited. Please forward comments to
hubmib@hprnd.rose.hp.com.
Table of Contents
1. Introduction ................................................ 2
2. The SNMP Management Framework .............................. 3
3. Overview ................................................... 4
3.1. Relation to MIB-2 ........................................ 4
3.2. Relation to the Interfaces MIB ........................... 5
3.2.1. Layering Model ......................................... 5
3.2.2. Virtual Circuits ....................................... 5
3.2.3. ifTestTable ............................................ 5
3.2.4. ifRcvAddressTable ...................................... 6
3.2.5. ifPhysAddress .......................................... 6
3.2.6. ifType ................................................. 7
3.2.7. Specific Interface MIB Objects ......................... 7
3.3. Relation to the 802.3 MAU MIB ............................ 11
3.4. Mapping of IEEE 802.3 Managed Objects .................... 11
4. Definitions ................................................ 12
5. Intellectual Property ...................................... 40
6. Acknowledgements ........................................... 41
7. References ................................................. 42
8. Security Considerations .................................... 45
9. Author's Addresses ......................................... 45
A. Change Log ................................................. 46
A.1. Changes since RFC 2358 ................................... 46
A.2. Changes between RFC 1650 and RFC 2358 .................... 47
B. Full Copyright Statement ................................... 47
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines objects for managing Ethernet-like
interfaces.
This memo also includes a MIB module. This MIB module extends the
list of managed objects specified in the earlier version of this MIB:
RFC2358 [26].
Flick, et. al. Expires February 1999 [Page 2]
Internet Draft Ethernet-Like MIB August 1998
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [29].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2271 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [2], RFC 1212 [3] and RFC 1215 [4]. The second version,
called SMIv2, is described in RFC 1902 [5], RFC 1903 [6] and RFC
1904 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [8]. A second version of the SNMP message
protocol, which is not an Internet standards track protocol, is
called SNMPv2c and described in RFC 1901 [9] and RFC 1906 [10].
The third version of the message protocol is called SNMPv3 and
described in RFC 1906 [10], RFC 2272 [11] and RFC 2274 [12].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [8]. A second set of protocol operations
and associated PDU formats is described in RFC 1905 [13].
o A set of fundamental applications described in RFC 2273 [14] and
the view-based access control mechanism described in RFC 2275
[15].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
Flick, et. al. Expires February 1999 [Page 3]
Internet Draft Ethernet-Like MIB August 1998
MIB.
3. Overview
Instances of these object types represent attributes of an interface
to an ethernet-like communications medium. At present, ethernet-like
media are identified by the following values of the ifType object in
the Interfaces MIB [28]:
ethernetCsmacd(6)
iso88023Csmacd(7)
starLan(11)
The definitions presented here are based on IEEE Draft 802.3z/D4.2,
Section 30 [19], as originally interpreted by Frank Kastenholz then
of Interlan in [20]. Implementors of these MIB objects should note
that IEEE Std. 802.3 ([16], [17], and [18]) and IEEE Draft 802.3z
[19] explicitly describe (in the form of Pascal pseudocode) when,
where, and how various MAC attributes are measured. The IEEE
documents also describe the effects of MAC actions that may be
invoked by manipulating instances of the MIB objects defined here.
To the extent that some of the attributes defined in [19] are
represented by previously defined objects in MIB-2 [27] or in the
Interfaces MIB [28], such attributes are not redundantly represented
by objects defined in this memo. Among the attributes represented by
objects defined in other memos are the number of octets transmitted
or received on a particular interface, the number of frames
transmitted or received on a particular interface, the promiscuous
status of an interface, the MAC address of an interface, and
multicast information associated with an interface.
3.1. Relation to MIB-2
This section applies only when this MIB is used in conjunction with
the "old" (RFC 1213) [27] interface group.
The relationship between an ethernet-like interface and an interface
in the context of the Internet-standard MIB is one-to-one. As such,
the value of an ifIndex object instance can be directly used to
identify corresponding instances of the objects defined herein.
For agents which implement the (now deprecated) ifSpecific object, an
instance of that object that is associated with an ethernet-like
interface has the OBJECT IDENTIFIER value:
Flick, et. al. Expires February 1999 [Page 4]
Internet Draft Ethernet-Like MIB August 1998
dot3 OBJECT IDENTIFER ::= { transmission 7 }
3.2. Relation to the Interfaces MIB
The Interface MIB [28] requires that any MIB which is an adjunct of
the Interface MIB clarify specific areas within the Interface MIB.
These areas were intentionally left vague in the Interface MIB to
avoid over constraining the MIB, thereby precluding management of
certain media-types.
Section 3.3 of [28] enumerates several areas which a media-specific
MIB must clarify. Each of these areas is addressed in a following
subsection. The implementor is referred to [28] in order to
understand the general intent of these areas.
3.2.1. Layering Model
This MIB does not provide for layering. There are no sublayers.
EDITOR'S NOTE:
One could foresee the development of an 802.2 and enet-transceiver
MIB. They could be higher and lower sublayers, respectively. All
that THIS document should do is allude to the possibilities and urge
the implementor to be aware of the possibility and that they may have
requirements which supersede the requirements in this document.
3.2.2. Virtual Circuits
This medium does not support virtual circuits and this area is not
applicable to this MIB.
3.2.3. ifTestTable
This MIB defines two tests for media which are instrumented with this
MIB; TDR and Loopback. Implementation of these tests is not
required. Many common interface chips do not support one or both of
these tests.
These two tests are provided as a convenience, allowing a common
method to invoke the test.
Standard MIBs do not include objects in which to return the results
Flick, et. al. Expires February 1999 [Page 5]
Internet Draft Ethernet-Like MIB August 1998
of the TDR test. Any needed objects MUST be provided in the vendor
specific MIB.
Note that the ifTestTable is now deprecated. Work is underway to
define a replacement MIB for system and interface testing. It is
expected that the tests defined in this document will be usable in
this replacement MIB.
3.2.4. ifRcvAddressTable
This table contains all IEEE 802.3 addresses, unicast, multicast, and
broadcast, for which this interface will receive packets and forward
them up to a higher layer entity for local consumption. The format
of the address, contained in ifRcvAddressAddress, is the same as for
ifPhysAddress.
In the event that the interface is part of a MAC bridge, this table
does not include unicast addresses which are accepted for possible
forwarding out some other port. This table is explicitly not
intended to provide a bridge address filtering mechanism.
3.2.5. ifPhysAddress
This object contains the IEEE 802.3 address which is placed in the
source-address field of any Ethernet, Starlan, or IEEE 802.3 frames
that originate at this interface. Usually this will be kept in ROM
on the interface hardware. Some systems may set this address via
software.
In a system where there are several such addresses the designer has a
tougher choice. The address chosen should be the one most likely to
be of use to network management (e.g. the address placed in ARP
responses for systems which are primarily IP systems).
If the designer truly can not chose, use of the factory- provided ROM
address is suggested.
If the address can not be determined, an octet string of zero length
should be returned.
The address is stored in binary in this object. The address is
stored in "canonical" bit order, that is, the Group Bit is positioned
as the low-order bit of the first octet. Thus, the first byte of a
multicast address would have the bit 0x01 set.
Flick, et. al. Expires February 1999 [Page 6]
Internet Draft Ethernet-Like MIB August 1998
3.2.6. ifType
This MIB applies to interfaces which have any of the following ifType
values:
ethernetCsmacd(6)
iso88023Csmacd(7)
starLan(11)
It is RECOMMENDED that all Ethernet-like interfaces use an ifType of
ethernetCsmacd(6) regardless of the speed that the interface is
running or the link-layer encapsulation in use. iso88023Csmacd(7)
and starLan(11) are supported for backwards compatability.
There are three other interface types defined in the IANAifType-MIB
for 100 Mbit Ethernet. They are fastEther(62), fastEtherFX(69), and
gigabitEthernet(117). This document takes the position that an
Ethernet is an Ethernet, and Ethernet interfaces SHOULD always have
the same value of ifType. Information on the particular flavor of
Ethernet that an interface is running is available from ifSpeed in
the Interfaces MIB, and ifMauType in the 802.3 MAU MIB. An
Ethernet-like interface SHOULD NOT use the fastEther(62),
fastEtherFX(69), or gigabitEthernet(117) ifTypes.
Interfaces with any of the supported ifType values map to the
EtherLike-MIB in the same manner. Which compliance statement an
interface should implement is dependent on the maximum speed
supported on the interface. The EtherLike-MIB etherCompliance
compliance statement applies to all Ethernet-like interfaces whose
maximum supported speed is 10 Mbit/sec or less. There are no
implementation differences. Similarly, the EtherLike-MIB
ether100MbsCompliance compliance statement applies to all Ethernet-
like interfaces whose maximum supported speed is 100Mbit/sec.
An interface that is capable of operating at 100Mbit/sec MUST
implement the ether100MbsCompliance compliance statement, even if it
is currently operating at a lower speed. Counters in the
ether100MbsCompliance compliance statement that only apply to 100
Mbit interfaces would simply not increment when the interface is
operating at a lower speed.
3.2.7. Specific Interface MIB Objects
The following table provides specific implementation guidelines for
applying the interface group objects to ethernet-like media.
Object
Flick, et. al. Expires February 1999 [Page 7]
Internet Draft Ethernet-Like MIB August 1998
ifIndex Each ethernet-like interface is
represented by an ifEntry. The
dot3StatsTable in this MIB module is
indexed by dot3StatsIndex. The interface
identified by a particular value of
dot3StatsIndex is the same interface as
identified by the same value of ifIndex.
ifDescr Refer to [28].
ifType Refer to section 3.2.6.
ifMtu 1500 octets. NOTE: This is the MTU as
seen by the MAC client. When a higher
layer protocol, like IP, is running over
Ethernet, this is the MTU that will be
seen by that higher layer protocol.
However, when using the IEEE 802.2 LLC
protocol, higher layer protocols will
see a different MTU. In particular, an
LLC type 1 client protocol will see
an MTU of 1497 octets, and a protocol
running over SNAP will see an MTU of
1492 octets.
ifSpeed The current operational speed of the
interface in bits per second. For
current ethernet-like interfaces, this
will be equal to 1,000,000 (1 million),
10,000,000 (10 million), 100,000,000
(100 million), or 1,000,000,000 (1
billion). If the interface implements
auto-negotiation, auto-negotiation is
enabled for this interface, and the
interface has not yet negotiated to an
operational speed, this object SHOULD
reflect the maximum speed supported by
the interface. Note that this object
MUST NOT indicate a doubled value when
operating in full-duplex mode. It MUST
indicate the correct line speed
regardless of the current duplex mode.
The correct object to use to determine
the duplex mode of the interface is the
ifMauType object in the 802.3 MAU MIB.
ifPhysAddress Refer to section 3.2.5.
Flick, et. al. Expires February 1999 [Page 8]
Internet Draft Ethernet-Like MIB August 1998
ifAdminStatus Write access is not required. Support
for 'testing' is not required.
ifOperStatus The operational state of the interface.
Support for 'testing' is not required.
The value 'dormant' has no meaning for
an ethernet-like interface.
ifLastChange Refer to [28].
ifInOctets The number of octets in valid MAC frames
received on this interface, including
the MAC header and FCS.
ifInUcastPkts Refer to [28].
ifInDiscards Refer to [28].
ifInErrors The sum for this interface of
dot3StatsAlignmentErrors,
dot3StatsFCSErrors,
dot3StatsFrameTooLongs,
dot3StatsInternalMacReceiveErrors and
dot3StatsSymbolErrors.
ifInUnknownProtos Refer to [28].
ifOutOctets The number of octets transmitted in
valid MAC frames on this interface,
including the MAC header and FCS.
ifOutUcastPkts Refer to [28].
ifOutDiscards Refer to [28].
ifOutErrors The sum for this interface of:
dot3StatsSQETestErrors,
dot3StatsLateCollisions,
dot3StatsExcessiveCollisions,
dot3StatsInternalMacTransmitErrors and
dot3StatsCarrierSenseErrors.
ifName Locally-significant textual name for the
interface (e.g. lan0).
ifInMulticastPkts Refer to [28].
ifInBroadcastPkts Refer to [28].
Flick, et. al. Expires February 1999 [Page 9]
Internet Draft Ethernet-Like MIB August 1998
ifOutMulticastPkts Refer to [28].
ifOutBroadcastPkts Refer to [28].
ifHCInOctets 64-bit versions of counters. Required
ifHCOutOctets for ethernet-like interfaces that are
capable of operating at 20Mbit/sec or
faster, even if the interface is
currently operating at less than
20Mbit/sec.
ifHCInUcastPkts 64-bit versions of packet counters.
ifHCInMulticastPkts Support for these counters is not
ifHCInBroadcastPkts required for the interface types
ifHCOutUcastPkts supported by this MIB. They are only
ifHCOutMulticastPkts required for interfaces capable of
ifHCOutBroadcastPkts operating at 640Mbit/sec or faster.
Note that a future revision of this
document may support faster interfaces,
and therefore may require support for
these counters.
ifLinkUpDownTrapEnable Refer to [28]. Default is 'enabled'
ifHighSpeed The current operational speed of the
interface in millions of bits per
second. For current ethernet-like
interfaces, this will be equal to 1, 10,
100, or 1,000. If the interface
implements auto-negotiation,
auto-negotiation is enabled for this
interface, and the interface has not yet
negotiated to an operational speed, this
object SHOULD reflect the maximum speed
supported by the interface. Note that
this object MUST NOT indicate a doubled
value when operating in full-duplex
mode. It MUST indicate the correct line
speed regardless of the current duplex
mode. The correct object to use to
determine the duplex mode of the
interface is the ifMauType object in the
802.3 MAU MIB.
ifPromiscuousMode Refer to [28].
ifConnectorPresent This will normally be 'true'.
Flick, et. al. Expires February 1999 [Page 10]
Internet Draft Ethernet-Like MIB August 1998
ifAlias Refer to [28].
ifCounterDiscontinuityTime Refer to [28].
ifStackHigherLayer Refer to section 3.2.1.
ifStackLowerLayer
ifStackStatus
ifRcvAddressAddress Refer to section 3.2.4.
ifRcvAddressStatus
ifRcvAddressType
3.3. Relation to the 802.3 MAU MIB
Support for the mauModIfCompl compliance statement of the MAU-MIB
[30] is REQUIRED for Ethernet-like interfaces. This MIB is needed in
order to allow applications to determine the current MAU type in use
by the interface. The MAU type indicates not only the media type in
use, but also indicates whether the interface is operating in half-
duplex or full-duplex mode. Implementing this MIB module without
implementing the MAU-MIB would leave applications with no standard
way to determine the duplex mode of the interface.
3.4. Mapping of IEEE 802.3 Managed Objects
IEEE 802.3 Managed Object Corresponding SNMP Object
oMacEntity
.aMACID dot3StatsIndex or
IF-MIB - ifIndex
.aFramesTransmittedOK IF-MIB - ifOutUCastPkts +
ifOutMulticastPkts +
ifOutBroadcastPkts
.aSingleCollisionFrames dot3StatsSingleCollisionFrames
.aMultipleCollisionFrames dot3StatsMultipleCollisionFrames
.aFramesReceivedOK IF-MIB - ifInUcastPkts +
ifInMulticastPkts +
ifInBroadcastPkts
.aFrameCheckSequenceErrors dot3StatsFCSErrors
.aAlignmentErrors dot3StatsAlignmentErrors
.aOctetsTransmittedOK IF-MIB - ifOutOctets*
.aFramesWithDeferredXmissions dot3StatsDeferredTransmissions
.aLateCollisions dot3StatsLateCollisions
.aFramesAbortedDueToXSColls dot3StatsExcessiveCollisions
.aFramesLostDueToIntMACXmitError dot3StatsInternalMacTransmitErrors
.aCarrierSenseErrors dot3StatsCarrierSenseErrors
Flick, et. al. Expires February 1999 [Page 11]
Internet Draft Ethernet-Like MIB August 1998
.aOctetsReceivedOK IF-MIB - ifInOctets*
.aFramesLostDueToIntMACRcvError dot3StatsInternalMacReceiveErrors
.aPromiscuousStatus IF-MIB - ifPromiscuousMode
.aReadMulticastAddressList IF-MIB - ifRcvAddressTable
.aMulticastFramesXmittedOK IF-MIB - ifOutMulticastPkts
.aBroadcastFramesXmittedOK IF-MIB - ifOutBroadcastPkts
.aMulticastFramesReceivedOK IF-MIB - ifInMulticastPkts
.aBroadcastFramesReceivedOK IF-MIB - ifInBroadcastPkts
.aFrameTooLongErrors dot3StatsFrameTooLongs
.aReadWriteMACAddress IF-MIB - ifPhysAddress
.aCollisionFrames dot3CollFrequencies
.acAddGroupAddress IF-MIB - ifRcvAddressTable
.acDeleteGroupAddress IF-MIB - ifRcvAddressTable
.acExecuteSelfTest dot3TestLoopBack
oPHYEntity
.aSQETestErrors dot3StatsSQETestErrors
.aSymbolErrorDuringCarrier dot3StatsSymbolErrors
* Note that the octet counters in IF-MIB do not exactly match the
definition of the octet counters in IEEE 802.3. aOctetsTransmittedOK
and aOctetsReceivedOK count only the octets in the clientData and Pad
fields, whereas ifInOctets and ifOutOctets include the entire MAC
frame, including MAC header and FCS. However, the IF-MIB counters
can be derived from the IEEE 802.3 counters as follows:
ifInOctets = aOctetsReceivedOK + (18 * aFramesReceivedOK)
ifOutOctets = aOctetsTransmittedOK + (18 * aFramesTransmittedOK)
The following IEEE 802.3 managed objects have been removed from this
MIB module as a result of implementation feedback:
oMacEntity
.aFramesWithExcessiveDeferral
.aInRangeLengthErrors
.aOutOfRangeLengthField
.aMACEnableStatus
.aTransmitEnableStatus
.aMulticastReceiveStatus
.acInitializeMAC
Please see [22] for the detailed reasoning on why these objects were
removed.
4. Definitions
Flick, et. al. Expires February 1999 [Page 12]
Internet Draft Ethernet-Like MIB August 1998
EtherLike-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,
Counter32, Unsigned32, mib-2, transmission
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex, InterfaceIndex
FROM IF-MIB;
etherMIB MODULE-IDENTITY
LAST-UPDATED "9808042227Z" -- August 4, 1998
ORGANIZATION "IETF 802.3 Hub MIB Working Group"
CONTACT-INFO
"WG E-mail: hubmib@hprnd.rose.hp.com
To subscribe: hubmib-request@hprnd.rose.hp.com
Chair: Dan Romascanu
Postal: LANNET Ltd.
Atidum Technology Park, Bldg. 3
Tel Aviv 61131
Israel
Tel: +972 3 645 8414
E-mail: dromasca@lannet.com
Editor: John Flick
Postal: Hewlett-Packard Company
8000 Foothills Blvd. M/S 5556
Roseville, CA 95747-5556
USA
Tel: +1 916 785 4018
Fax: +1 916 785 3583
E-mail: johnf@rose.hp.com
Editor: Jeffrey Johnson
Postal: RedBack Networks
2570 North First Street, Suite 410
San Jose, CA, 95131
USA
Tel: +1 408 571 2699
Fax: +1 408 571 2698
E-Mail: jeff@redbacknetworks.com"
DESCRIPTION "The MIB module to describe generic objects for
Ethernet-like network interfaces.
The following reference is used throughout this
Flick, et. al. Expires February 1999 [Page 13]
Internet Draft Ethernet-Like MIB August 1998
MIB module:
[IEEE 802.3 Std] refers to:
ISO/IEC 8802-3: 1996(E), (ANSI/IEEE
Std 802.3, 1996 Edition), 'Information
technology - Telecommunications and
information exchange between systems - Local
and metropolitan area networks - Specific
requirements - Part 3: Carrier sense
multiple access with collision detection
(CSMA/CD) access method and physical layer
specifications', July 1996.
as ammended by the following supplements:
IEEE Std 802.3u-1995, 'Media Access Control
(MAC) Parameters, Physical Layer, Medium
Attachment Units, and Repeater for 100Mb/s
Operation, Type 100BASE-T', October 1995.
IEEE Std 802.3x-1997 and IEEE Std
802.3y-1997, 'Specification for 802.3 Full
Duplex Operation and Physical Layer
Specification for 100Mbit/s Operation on Two
Pairs of Category 3 or Better Balanced
Twisted Pair Cable (100BASE-T2)', November
1997.
IEEE Draft 802.3z/D4.2, 'Media Access
Control (MAC) Parameters, Physical Layer,
Repeater and Management Parameters for 1000
Mb/s Operation', March 1998.
Of particular interest is Clause 30, '10Mb/s,
100Mb/s and 1000Mb/s Management', which is
specified in IEEE Draft 802.3z/D4.2."
REVISION "9808042227Z"
DESCRIPTION "Updated to include support for 1000 Mb/sec
interfaces and full-duplex interfaces."
REVISION "9806032150Z"
DESCRIPTION "Updated to include support for 100 Mb/sec
interfaces. Published as RFC 2358."
REVISION "9402030400Z"
DESCRIPTION "Version published as RFC 1650."
::= { mib-2 35 }
Flick, et. al. Expires February 1999 [Page 14]
Internet Draft Ethernet-Like MIB August 1998
etherMIBObjects OBJECT IDENTIFIER ::= { etherMIB 1 }
dot3 OBJECT IDENTIFIER ::= { transmission 7 }
-- the Ethernet-like Statistics group
dot3StatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3StatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Statistics for a collection of ethernet-like
interfaces attached to a particular system."
::= { dot3 2 }
dot3StatsEntry OBJECT-TYPE
SYNTAX Dot3StatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Statistics for a particular interface to an
ethernet-like medium."
INDEX { dot3StatsIndex }
::= { dot3StatsTable 1 }
Dot3StatsEntry ::=
SEQUENCE {
dot3StatsIndex InterfaceIndex,
dot3StatsAlignmentErrors Counter32,
dot3StatsFCSErrors Counter32,
dot3StatsSingleCollisionFrames Counter32,
dot3StatsMultipleCollisionFrames Counter32,
dot3StatsSQETestErrors Counter32,
dot3StatsDeferredTransmissions Counter32,
dot3StatsLateCollisions Counter32,
dot3StatsExcessiveCollisions Counter32,
dot3StatsInternalMacTransmitErrors Counter32,
dot3StatsCarrierSenseErrors Counter32,
dot3StatsFrameTooLongs Counter32,
dot3StatsInternalMacReceiveErrors Counter32,
dot3StatsEtherChipSet OBJECT IDENTIFIER,
dot3StatsSymbolErrors Counter32
}
dot3StatsIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION "An index value that uniquely identifies an
interface to an ethernet-like medium. The
Flick, et. al. Expires February 1999 [Page 15]
Internet Draft Ethernet-Like MIB August 1998
interface identified by a particular value of
this index is the same interface as identified
by the same value of ifIndex."
REFERENCE "RFC 2233, ifIndex"
::= { dot3StatsEntry 1 }
dot3StatsAlignmentErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames received on a particular
interface that are not an integral number of
octets in length and do not pass the FCS check.
The count represented by an instance of this
object is incremented when the alignmentError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.
This counter does not increment for 8-bit wide
group encoding schemes."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.7,
aAlignmentErrors"
::= { dot3StatsEntry 2 }
dot3StatsFCSErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames received on a particular
interface that are an integral number of octets
in length but do not pass the FCS check. This
count does not include frames received with
frame-too-long or frame-too-short error.
The count represented by an instance of this
object is incremented when the frameCheckError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.
Flick, et. al. Expires February 1999 [Page 16]
Internet Draft Ethernet-Like MIB August 1998
Note: Coding errors detected by the physical
layer for speeds above 10 Mb/s will cause the
frame to fail the FCS check."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.6,
aFrameCheckSequenceErrors."
::= { dot3StatsEntry 3 }
dot3StatsSingleCollisionFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by exactly one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the dot3StatsMultipleCollisionFrames
object.
This counter does not increment when the
interface is operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.3,
aSingleCollisionFrames."
::= { dot3StatsEntry 4 }
dot3StatsMultipleCollisionFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the dot3StatsSingleCollisionFrames
object.
This counter does not increment when the
interface is operating in full-duplex mode."
Flick, et. al. Expires February 1999 [Page 17]
Internet Draft Ethernet-Like MIB August 1998
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.4,
aMultipleCollisionFrames."
::= { dot3StatsEntry 5 }
dot3StatsSQETestErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of times that the SQE TEST ERROR
message is generated by the PLS sublayer for a
particular interface. The SQE TEST ERROR
is set in accordance with the rules for
verification of the SQE detection mechanism in
the PLS Carrier Sense Function as described in
ANSI/IEEE 802.3-1996, section 7.2.4.6.
This counter does not increment on interfaces
operating at speeds greater than 10 Mb/s, or on
interfaces operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 7.2.4.6, also 30.3.2.1.4,
aSQETestErrors."
::= { dot3StatsEntry 6 }
dot3StatsDeferredTransmissions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames for which the first
transmission attempt on a particular interface
is delayed because the medium is busy.
The count represented by an instance of this
object does not include frames involved in
collisions.
This counter does not increment when the
interface is operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.9,
aFramesWithDeferredXmissions."
::= { dot3StatsEntry 7 }
dot3StatsLateCollisions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of times that a collision is
detected on a particular interface later than
Flick, et. al. Expires February 1999 [Page 18]
Internet Draft Ethernet-Like MIB August 1998
one slotTime into the transmission of a packet.
A (late) collision included in a count
represented by an instance of this object is
also considered as a (generic) collision for
purposes of other collision-related
statistics.
This counter does not increment when the
interface is operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.10,
aLateCollisions."
::= { dot3StatsEntry 8 }
dot3StatsExcessiveCollisions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames for which transmission on a
particular interface fails due to excessive
collisions.
This counter does not increment when the
interface is operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.11,
aFramesAbortedDueToXSColls."
::= { dot3StatsEntry 9 }
dot3StatsInternalMacTransmitErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames for which transmission on a
particular interface fails due to an internal
MAC sublayer transmit error. A frame is only
counted by an instance of this object if it is
not counted by the corresponding instance of
either the dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or the
dot3StatsCarrierSenseErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of transmission
errors on a particular interface that are not
otherwise counted."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.12,
Flick, et. al. Expires February 1999 [Page 19]
Internet Draft Ethernet-Like MIB August 1998
aFramesLostDueToIntMACXmitError."
::= { dot3StatsEntry 10 }
dot3StatsCarrierSenseErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of times that the carrier sense
condition was lost or never asserted when
attempting to transmit a frame on a particular
interface.
The count represented by an instance of this
object is incremented at most once per
transmission attempt, even if the carrier sense
condition fluctuates during a transmission
attempt.
This counter does not increment when the
interface is operating in full-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.13,
aCarrierSenseErrors."
::= { dot3StatsEntry 11 }
-- { dot3StatsEntry 12 } is not assigned
dot3StatsFrameTooLongs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames received on a particular
interface that exceed the maximum permitted
frame size.
The count represented by an instance of this
object is incremented when the frameTooLong
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.25,
aFrameTooLongErrors."
::= { dot3StatsEntry 13 }
-- { dot3StatsEntry 14 } is not assigned
Flick, et. al. Expires February 1999 [Page 20]
Internet Draft Ethernet-Like MIB August 1998
-- { dot3StatsEntry 15 } is not assigned
dot3StatsInternalMacReceiveErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of frames for which reception on a
particular interface fails due to an internal
MAC sublayer receive error. A frame is only
counted by an instance of this object if it is
not counted by the corresponding instance of
either the dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of receive errors
on a particular interface that are not
otherwise counted."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.15,
aFramesLostDueToIntMACRcvError."
::= { dot3StatsEntry 16 }
dot3StatsEtherChipSet OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This object contains an OBJECT IDENTIFIER
which identifies the chipset used to
realize the interface. Ethernet-like
interfaces are typically built out of
several different chips. The MIB implementor
is presented with a decision of which chip
to identify via this object. The implementor
should identify the chip which is usually
called the Medium Access Control chip.
If no such chip is easily identifiable,
the implementor should identify the chip
which actually gathers the transmit
and receive statistics and error
indications. This would allow a
manager station to correlate the
statistics and the chip generating
them, giving it the ability to take
into account any known anomalies
in the chip."
Flick, et. al. Expires February 1999 [Page 21]
Internet Draft Ethernet-Like MIB August 1998
::= { dot3StatsEntry 17 }
dot3StatsSymbolErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "For an interface operating at 100 Mb/s, the
number of times there was an invalid data symbol
when a valid carrier was present.
For an interface operating in half-duplex mode
at 1000 Mb/s, the number of times the receiving
media is non-idle (a carrier event) for a period
of time equal to or greater than slotTime, and
during which there was at least one occurrence
of an event that causes the PHY to indicate
'Data reception error' or 'carrier extend error'
on the GMII.
For an interface operating in full-duplex mode
at 1000 Mb/s, the number of times the receiving
media is non-idle a carrier event) for a period
of time equal to or greater than minFrameSize,
and during which there was at least one
occurrence of an event that causes the PHY to
indicate 'Data reception error' on the GMII.
The count represented by an instance of this
object is incremented at most once per carrier
event, even if multiple symbol errors occur
during the carrier event. This count does
not increment if a collision is present."
REFERENCE "[IEEE 802.3 Std.], 30.3.2.1.5,
aSymbolErrorDuringCarrier."
::= { dot3StatsEntry 18 }
-- the Ethernet-like Collision Statistics group
-- Implementation of this group is optional; it is appropriate
-- for all systems which have the necessary metering
dot3CollTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3CollEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A collection of collision histograms for a
particular set of interfaces."
REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.30,
Flick, et. al. Expires February 1999 [Page 22]
Internet Draft Ethernet-Like MIB August 1998
aCollisionFrames."
::= { dot3 5 }
dot3CollEntry OBJECT-TYPE
SYNTAX Dot3CollEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A cell in the histogram of per-frame
collisions for a particular interface. An
instance of this object represents the
frequency of individual MAC frames for which
the transmission (successful or otherwise) on a
particular interface is accompanied by a
particular number of media collisions."
INDEX { ifIndex, dot3CollCount }
::= { dot3CollTable 1 }
Dot3CollEntry ::=
SEQUENCE {
dot3CollCount INTEGER,
dot3CollFrequencies Counter32
}
-- { dot3CollEntry 1 } is no longer in use
dot3CollCount OBJECT-TYPE
SYNTAX INTEGER (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The number of per-frame media collisions for
which a particular collision histogram cell
represents the frequency on a particular
interface."
::= { dot3CollEntry 2 }
dot3CollFrequencies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of individual MAC frames for which the
transmission (successful or otherwise) on a
particular interface occurs after the
frame has experienced exactly the number
of collisions in the associated
dot3CollCount object.
Flick, et. al. Expires February 1999 [Page 23]
Internet Draft Ethernet-Like MIB August 1998
For example, a frame which is transmitted
on interface 77 after experiencing
exactly 4 collisions would be indicated
by incrementing only dot3CollFrequencies.77.4.
No other instance of dot3CollFrequencies would
be incremented in this example.
This counter does not increment when the
interface is operating in full-duplex mode."
::= { dot3CollEntry 3 }
dot3ControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3ControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table of descriptive and status information
about the MAC Control sublayer on the
ethernet-like interfaces attached to a
particular system."
::= { dot3 9 }
dot3ControlEntry OBJECT-TYPE
SYNTAX Dot3ControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the table, containing information
about the MAC Control sublayer on a single
ethernet-like interface."
INDEX { dot3StatsIndex }
::= { dot3ControlTable 1 }
Dot3ControlEntry ::=
SEQUENCE {
dot3ControlFunctionsSupported BITS,
dot3ControlInUnknownOpcodes Counter32,
dot3ControlPauseMode INTEGER,
dot3ControlPauseLinkDelayAllowance Unsigned32,
dot3ControlInPauseFrames Counter32,
dot3ControlOutPauseFrames Counter32
}
dot3ControlFunctionsSupported OBJECT-TYPE
SYNTAX BITS {
pause(0)
}
MAX-ACCESS read-write
STATUS current
Flick, et. al. Expires February 1999 [Page 24]
Internet Draft Ethernet-Like MIB August 1998
DESCRIPTION "A list of the possible MAC Control functions
implemented for this interface."
REFERENCE "[IEEE 802.3 Std.], 30.3.3.2,
aMACControlFunctionsSupported."
::= { dot3ControlEntry 1 }
dot3ControlInUnknownOpcodes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of MAC Control frames received on this
interface that contain an opcode that is not
supported by this device."
REFERENCE "[IEEE 802.3 Std.], 30.3.3.5,
aUnsupportedOpcodesReceived"
::= { dot3ControlEntry 2 }
dot3ControlPauseMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabledXmit(2),
enabledRcv(3),
enabledXmitAndRcv(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This object reflects the PAUSE mode currently
in use on this interface. Interfaces operating
at less than 1000 Mb/s will never return
'enabledXmit(2)' or 'enabledRcv(3)'. Interfaces
which have not yet completed auto-negotiation
should return the value 'disabled(1)'."
::= { dot3ControlEntry 3 }
dot3ControlPauseLinkDelayAllowance OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The allowance, in bit times, made by the PAUSE
MAC Control entity for round-trip propagation
delay of the full-duplex link."
REFERENCE "[IEEE 802.3 Std.], 30.3.4.1,
aPAUSELinkDelayAllowance."
::= { dot3ControlEntry 4 }
dot3ControlInPauseFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Flick, et. al. Expires February 1999 [Page 25]
Internet Draft Ethernet-Like MIB August 1998
STATUS current
DESCRIPTION "A count of MAC Control frames received on this
interface with an opcode indicating the PAUSE
operation.
This counter does not increment when the
interface is operating in half-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.4.3,
aPAUSEMACCtrlFramesReceived."
::= { dot3ControlEntry 5 }
dot3ControlOutPauseFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "A count of MAC Control frames transmitted on
this interface with an opcode indicating the
PAUSE operation.
This counter does not increment when the
interface is operating in half-duplex mode."
REFERENCE "[IEEE 802.3 Std.], 30.3.4.2,
aPAUSEMACCtrlFramesTransmitted."
::= { dot3ControlEntry 6 }
-- 802.3 Tests
dot3Tests OBJECT IDENTIFIER ::= { dot3 6 }
dot3Errors OBJECT IDENTIFIER ::= { dot3 7 }
-- TDR Test
dot3TestTdr OBJECT-IDENTITY
STATUS current
DESCRIPTION "The Time-Domain Reflectometry (TDR) test is
specific to ethernet-like interfaces of type
10Base5 and 10Base2. The TDR value may be
useful in determining the approximate distance
to a cable fault. It is advisable to repeat
this test to check for a consistent resulting
TDR value, to verify that there is a fault.
A TDR test returns as its result the time
interval, measured in 10 MHz ticks or 100 nsec
units, between the start of TDR test
Flick, et. al. Expires February 1999 [Page 26]
Internet Draft Ethernet-Like MIB August 1998
transmission and the subsequent detection of a
collision or deassertion of carrier. On
successful completion of a TDR test, the result
is stored as the value of an appropriate
instance of an appropriate vendor specific MIB
object, and the OBJECT IDENTIFIER of that
instance is stored in the appropriate instance
of the appropriate test result code object
(thereby indicating where the result has been
stored)."
::= { dot3Tests 1 }
-- Loopback Test
dot3TestLoopBack OBJECT-IDENTITY
STATUS current
DESCRIPTION "This test configures the MAC chip and executes
an internal loopback test of memory, data paths,
and the MAC chip logic. This loopback test can
only be executed if the interface is offline.
Once the test has completed, the MAC chip should
be reinitialized for network operation, but it
should remain offline.
If an error occurs during a test, the
appropriate test result object will be set
to indicate a failure. The two OBJECT
IDENTIFIER values dot3ErrorInitError and
dot3ErrorLoopbackError may be used to provided
more information as values for an appropriate
test result code object."
::= { dot3Tests 2 }
dot3ErrorInitError OBJECT-IDENTITY
STATUS current
DESCRIPTION "Couldn't initialize MAC chip for test."
::= { dot3Errors 1 }
dot3ErrorLoopbackError OBJECT-IDENTITY
STATUS current
DESCRIPTION "Expected data not received (or not received
correctly) in loopback test."
::= { dot3Errors 2 }
-- 802.3 Hardware Chipsets
-- The object dot3StatsEtherChipSet is provided to
Flick, et. al. Expires February 1999 [Page 27]
Internet Draft Ethernet-Like MIB August 1998
-- identify the MAC hardware used to communicate on an
-- interface. The following hardware chipsets are
-- registered:
dot3ChipSets OBJECT IDENTIFIER ::= { dot3 8 }
dot3ChipSetAMD OBJECT IDENTIFIER ::= { dot3ChipSets 1 }
dot3ChipSetAMD7990 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am7990 Local Area Network
Controller for Ethernet (LANCE)."
::= { dot3ChipSetAMD 1 }
dot3ChipSetAMD79900 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79900 chip."
::= { dot3ChipSetAMD 2 }
dot3ChipSetAMD79C940 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C940 Media Access Controller
for Ethernet (MACE)."
::= { dot3ChipSetAMD 3 }
dot3ChipSetAMD79C90 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C90 CMOS Local Area Network
Controller for Ethernet (C-LANCE)."
::= { dot3ChipSetAMD 4 }
dot3ChipSetAMD79C960 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C960 PCnet-ISA Single Chip
Ethernet Controller for ISA."
::= { dot3ChipSetAMD 5 }
dot3ChipSetAMD79C961 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C961 PCnet-ISA+ Single Chip
Plug & Play Full-Duplex Ethernet Controller
for ISA."
Flick, et. al. Expires February 1999 [Page 28]
Internet Draft Ethernet-Like MIB August 1998
::= { dot3ChipSetAMD 6 }
dot3ChipSetAMD79C961A OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C961A PCnet-ISA II Single Chip
Plug & Play Full-Duplex Ethernet Controller
for ISA."
::= { dot3ChipSetAMD 7 }
dot3ChipSetAMD79C965 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C965 PCnet-32 Single Chip
Ethernet Controller for PCI."
::= { dot3ChipSetAMD 8 }
dot3ChipSetAMD79C970 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C970 PCnet PCI Single Chip
Ethernet Controller for PCI Local Bus."
::= { dot3ChipSetAMD 9 }
dot3ChipSetAMD79C970A OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices AM79C970A PCnet PCI II Single Chip
Full-Duplex Ethernet Controller for PCI Local
Bus."
::= { dot3ChipSetAMD 10 }
dot3ChipSetAMD79C971 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C971 PCnet-FAST Single Chip
Full-Duplex 10/100 Mbps Ethernet Controller for
PCI Local Bus."
::= { dot3ChipSetAMD 11 }
dot3ChipSetAMD79C972 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Advanced
Micro Devices Am79C972 PCnet-FAST+ Enhanced
10/100 Mbps PCI Ethernet Controller with OnNow
Support."
::= { dot3ChipSetAMD 12 }
Flick, et. al. Expires February 1999 [Page 29]
Internet Draft Ethernet-Like MIB August 1998
dot3ChipSetIntel OBJECT IDENTIFIER ::= { dot3ChipSets 2 }
dot3ChipSetIntel82586 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Intel
82586 IEEE 802.3 Ethernet LAN Coprocessor."
::= { dot3ChipSetIntel 1 }
dot3ChipSetIntel82596 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Intel
82596 High-Performance 32-Bit Local Area Network
Coprocessor."
::= { dot3ChipSetIntel 2 }
dot3ChipSetIntel82595 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Intel
82595 High Integration Ethernet Controller."
::= { dot3ChipSetIntel 3 }
dot3ChipSetIntel82557 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Intel
82557 Fast Ethernet PCI Bus Lan Controller."
::= { dot3ChipSetIntel 4 }
dot3ChipSetIntel82558 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Intel
82558 Fast Ethernet PCI Bus LAN Controller with
Integrated PHY."
::= { dot3ChipSetIntel 5 }
dot3ChipSetSeeq OBJECT IDENTIFIER ::= { dot3ChipSets 3 }
dot3ChipSetSeeq8003 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
8003 chip set."
::= { dot3ChipSetSeeq 1 }
dot3ChipSetSeeq80C03 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
80C03 Full-Duplex CMOS Ethernet Data Link
Controller (MAC)."
::= { dot3ChipSetSeeq 2 }
Flick, et. al. Expires February 1999 [Page 30]
Internet Draft Ethernet-Like MIB August 1998
dot3ChipSetSeeq84C30 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
4-Port 84C30 Full-Duplex CMOS Ethernet 10
MBit/Sec Data Link Controller (MAC)."
::= { dot3ChipSetSeeq 3 }
dot3ChipSetSeeq8431 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
4-Port 8431 Full-Duplex CMOS Ethernet 10
MBit/Sec Data Link Controller (MAC)."
::= { dot3ChipSetSeeq 4 }
dot3ChipSetSeeq80C300 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
80C300 Full-Duplex CMOS Ethernet 10/100
Mbit/Sec Data Link Controller (MAC)."
::= { dot3ChipSetSeeq 5 }
dot3ChipSetSeeq84C300 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
4-Port 84C300 Fast Ethernet Controller (MAC)."
::= { dot3ChipSetSeeq 6 }
dot3ChipSetSeeq84301 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
4-Port 84301 Fast Ethernet Controller (MAC)."
::= { dot3ChipSetSeeq 7 }
dot3ChipSetSeeq84302 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
4-Port 84302 Fast Ethernet Controller (MAC)."
::= { dot3ChipSetSeeq 8 }
dot3ChipSetSeeq8100 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the SEEQ
8100 Gigabit Ethernet Controller (MAC & PCS)."
::= { dot3ChipSetSeeq 9 }
dot3ChipSetNational OBJECT IDENTIFIER ::= { dot3ChipSets 4 }
dot3ChipSetNational8390 OBJECT-IDENTITY
Flick, et. al. Expires February 1999 [Page 31]
Internet Draft Ethernet-Like MIB August 1998
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP8390 Network Interface
Controller."
::= { dot3ChipSetNational 1 }
dot3ChipSetNationalSonic OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83932 Systems-Oriented Network
Interface Controller (SONIC)."
::= { dot3ChipSetNational 2 }
dot3ChipSetNational83901 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83901 Serial Network Interface
Controller (SNIC)."
::= { dot3ChipSetNational 3 }
dot3ChipSetNational83902 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83902 Serial Network Interface
Controller for Twisted Pair (ST-NIC)."
::= { dot3ChipSetNational 4 }
dot3ChipSetNational83905 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83905 AT Local Area Network
Twisted-Pair Interface (AT/LANTIC)."
::= { dot3ChipSetNational 5 }
dot3ChipSetNational83907 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83907 AT Twisted-Pair Enhanced
Coaxial Network Interface Controller
(AT/LANTIC II)."
::= { dot3ChipSetNational 6 }
dot3ChipSetNational83916 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83916 Systems-Oriented Network
Interface Controller (SONIC-16)."
::= { dot3ChipSetNational 7 }
Flick, et. al. Expires February 1999 [Page 32]
Internet Draft Ethernet-Like MIB August 1998
dot3ChipSetNational83934 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83934 Systems-Oriented Network
Interface Controller with Twisted Pair Interface
(SONIC-T)."
::= { dot3ChipSetNational 8 }
dot3ChipSetNational83936 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the National
Semiconductor DP83936AVUL Full-Duplex Systems-
Oriented Network Interface Controller with
Twisted Pair Interface (SONIC-T)."
::= { dot3ChipSetNational 9 }
dot3ChipSetFujitsu OBJECT IDENTIFIER ::= { dot3ChipSets 5 }
dot3ChipSetFujitsu86950 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Fujitsu
86950 chip."
::= { dot3ChipSetFujitsu 1 }
dot3ChipSetFujitsu86960 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Fujitsu
MB86960 Network Interface Controller with
Encoder/Decoder (NICE)."
::= { dot3ChipSetFujitsu 2 }
dot3ChipSetFujitsu86964 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Fujitsu
MB86964 Ethernet Controller with 10BASE-T
Tranceiver."
::= { dot3ChipSetFujitsu 3 }
dot3ChipSetFujitsu86965A OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Fujitsu
MB86965A EtherCoupler Single-Chip Ethernet
Controller."
::= { dot3ChipSetFujitsu 4 }
dot3ChipSetFujitsu86965B OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Fujitsu
Flick, et. al. Expires February 1999 [Page 33]
Internet Draft Ethernet-Like MIB August 1998
MB86965B EtherCoupler Single-Chip Ethernet
Controller (supports full-duplex)."
::= { dot3ChipSetFujitsu 5 }
dot3ChipSetDigital OBJECT IDENTIFIER ::= { dot3ChipSets 6 }
dot3ChipSetDigitalDC21040 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor DC21040 chip."
::= { dot3ChipSetDigital 1 }
dot3ChipSetDigital21041 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21041 PCI Ethernet LAN
Controller."
::= { dot3ChipSetDigital 2 }
dot3ChipSetDigital21140 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21140 PCI Fast Ethernet LAN
Controller."
::= { dot3ChipSetDigital 3 }
dot3ChipSetDigital21143 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21143 PCI/CardBus 10/100-Mb/s
Ethernet LAN Controller."
::= { dot3ChipSetDigital 4 }
dot3ChipSetDigital21340 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21340 10/100-MB/s managed buffered
port switch."
::= { dot3ChipSetDigital 5 }
dot3ChipSetDigital21440 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21440 Multiport 10/100Mbps
Ethernet Controller."
::= { dot3ChipSetDigital 6 }
dot3ChipSetDigital21540 OBJECT-IDENTITY
Flick, et. al. Expires February 1999 [Page 34]
Internet Draft Ethernet-Like MIB August 1998
STATUS current
DESCRIPTION "The authoritative identifier for the Digital
Semiconductor 21540 PCI/CardBus Ethernet LAN
Controller with Modem Interface."
::= { dot3ChipSetDigital 7 }
dot3ChipSetTI OBJECT IDENTIFIER ::= { dot3ChipSets 7 }
dot3ChipSetTIE100 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Texas
Instruments TNETE100 ThunderLAN PCI Fast
Ethernet Controller."
::= { dot3ChipSetTI 1 }
dot3ChipSetTIE110 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Texas
Instruments TNETE110 ThunderLAN PCI 10BASE-T
Ethernet Adapter."
::= { dot3ChipSetTI 2 }
dot3ChipSetTIX3100 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Texas
Instruments TNETX3100 Desktop ThunderSWITCH
8/2."
::= { dot3ChipSetTI 3 }
dot3ChipSetTIX3150 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Texas
Instruments TNETX3150 ThunderSWITCH 12/3."
::= { dot3ChipSetTI 4 }
dot3ChipSetTIX3270 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Texas
Instruments TNETX3270 ThunderSWITCH 24/3."
::= { dot3ChipSetTI 5 }
dot3ChipSetToshiba OBJECT IDENTIFIER ::= { dot3ChipSets 8 }
dot3ChipSetToshibaTC35815F OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Toshiba
TC35815F PCI-Based 100/10Mbps Ethernet
Controller."
Flick, et. al. Expires February 1999 [Page 35]
Internet Draft Ethernet-Like MIB August 1998
::= { dot3ChipSetToshiba 1 }
dot3ChipSetLucent OBJECT IDENTIFIER ::= { dot3ChipSets 9 }
dot3ChipSetLucentATT1MX10 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Lucent
Technologies ATT1MX10 (Spinnaker) Quad MAC and
Tranceiver for Ethernet Frame Switching."
::= { dot3ChipSetLucent 1 }
dot3ChipSetLucentLUC3M08 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Lucent
Technologies LUC3M08 Eight Ethernet MACs for
10/100 Mbits/s Frame Switching."
::= { dot3ChipSetLucent 2 }
dot3ChipSetGalileo OBJECT IDENTIFIER ::= { dot3ChipSets 10 }
dot3ChipSetGalileoGT48001 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48001A Switched Ethernet
Controller."
::= { dot3ChipSetGalileo 1 }
dot3ChipSetGalileoGT48002 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48002A Switched Fast Ethernet
Controller."
::= { dot3ChipSetGalileo 2 }
dot3ChipSetGalileoGT48004 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48004A Four Port Fast Ethernet
Switch for Multiport 10/100BASE-X Systems."
::= { dot3ChipSetGalileo 3 }
dot3ChipSetGalileoGT48207 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48207 Low-Cost 10 Port Switched
Ethernet Controller for 10+10/100BASE-X."
::= { dot3ChipSetGalileo 4 }
Flick, et. al. Expires February 1999 [Page 36]
Internet Draft Ethernet-Like MIB August 1998
dot3ChipSetGalileoGT48208 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48208 Advanced 10 Port Switched
Ethernet Controller for 10+10/100BASE-X."
::= { dot3ChipSetGalileo 5 }
dot3ChipSetGalileoGT48212 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Galileo
Technology GT-48212 Advanced 14 Port Switched
Ethernet Controller for 10+10/100BASE-X."
::= { dot3ChipSetGalileo 6 }
dot3ChipSetJato OBJECT IDENTIFIER ::= { dot3ChipSets 11 }
dot3ChipSetJatoJT1001 OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the Jato
Technologies JT1001 GigEMAC Server
10/100/1000Mbps Ethernet Controller with PCI
interface."
::= { dot3ChipSetJato 1 }
dot3ChipSetXaQti OBJECT IDENTIFIER ::= { dot3ChipSets 12 }
dot3ChipSetXaQtiXQ11800FP OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the XaQTI
XQ11800FP XMAC II Gigabit Ethernet Media Access
Controller."
::= { dot3ChipSetXaQti 1 }
dot3ChipSetXaQtiXQ18110FP OBJECT-IDENTITY
STATUS current
DESCRIPTION "The authoritative identifier for the XaQTI
XQ18110FP GigaPower Protocol Accelerator."
::= { dot3ChipSetXaQti 2 }
-- For those chipsets not represented above, OBJECT IDENTIFIER
-- assignment is required in other documentation, e.g.,
-- assignment within that part of the registration tree
-- delegated to individual enterprises (see RFC 1155 and
-- RFC 1902).
--
-- In the future, management of chipset registrations may be
-- delegated to the Internet Assigned Numbers Authority (IANA).
Flick, et. al. Expires February 1999 [Page 37]
Internet Draft Ethernet-Like MIB August 1998
-- conformance information
etherConformance OBJECT IDENTIFIER ::= { etherMIB 2 }
etherGroups OBJECT IDENTIFIER ::= { etherConformance 1 }
etherCompliances OBJECT IDENTIFIER ::= { etherConformance 2 }
-- compliance statements
etherCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for managed network
entities which have ethernet-like network
interfaces."
MODULE -- this module
MANDATORY-GROUPS { etherStatsGroup }
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all systems which have the necessary
metering. Implementation in such systems is
highly recommended."
::= { etherCompliances 1 }
ether100MbsCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for managed network
entities which have 100 Mb/sec ethernet-like
network interfaces."
MODULE -- this module
MANDATORY-GROUPS { etherStats100MbsGroup }
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all systems which have the necessary
metering. Implementation in such systems is
highly recommended."
::= { etherCompliances 2 }
-- units of conformance
etherStatsGroup OBJECT-GROUP
OBJECTS { dot3StatsIndex,
dot3StatsAlignmentErrors,
dot3StatsFCSErrors,
Flick, et. al. Expires February 1999 [Page 38]
Internet Draft Ethernet-Like MIB August 1998
dot3StatsSingleCollisionFrames,
dot3StatsMultipleCollisionFrames,
dot3StatsSQETestErrors,
dot3StatsDeferredTransmissions,
dot3StatsLateCollisions,
dot3StatsExcessiveCollisions,
dot3StatsInternalMacTransmitErrors,
dot3StatsCarrierSenseErrors,
dot3StatsFrameTooLongs,
dot3StatsInternalMacReceiveErrors,
dot3StatsEtherChipSet
}
STATUS current
DESCRIPTION "A collection of objects providing information
applicable to all ethernet-like network
interfaces."
::= { etherGroups 1 }
etherCollisionTableGroup OBJECT-GROUP
OBJECTS { dot3CollFrequencies
}
STATUS current
DESCRIPTION "A collection of objects providing a histogram
of packets successfully transmitted after
experiencing exactly N collisions."
::= { etherGroups 2 }
etherStats100MbsGroup OBJECT-GROUP
OBJECTS { dot3StatsIndex,
dot3StatsAlignmentErrors,
dot3StatsFCSErrors,
dot3StatsSingleCollisionFrames,
dot3StatsMultipleCollisionFrames,
dot3StatsDeferredTransmissions,
dot3StatsLateCollisions,
dot3StatsExcessiveCollisions,
dot3StatsInternalMacTransmitErrors,
dot3StatsCarrierSenseErrors,
dot3StatsFrameTooLongs,
dot3StatsInternalMacReceiveErrors,
dot3StatsEtherChipSet,
dot3StatsSymbolErrors
}
STATUS current
DESCRIPTION "A collection of objects providing information
applicable to 100 Mb/sec ethernet-like network
Flick, et. al. Expires February 1999 [Page 39]
Internet Draft Ethernet-Like MIB August 1998
interfaces."
::= { etherGroups 3 }
etherControlGroup OBJECT-GROUP
OBJECTS { dot3ControlFunctionsSupported,
dot3ControlInUnknownOpcodes
}
STATUS current
DESCRIPTION "A collection of objects providing information
about the MAC Control sublayer on ethernet-like
network interfaces."
::= { etherGroups 4 }
etherControlPauseGroup OBJECT-GROUP
OBJECTS { dot3ControlPauseMode,
dot3ControlPauseLinkDelayAllowance,
dot3ControlInPauseFrames,
dot3ControlOutPauseFrames
}
STATUS current
DESCRIPTION "A collection of objects providing information
about the MAC Control PAUSE function on
ethernet-like network interfaces."
::= { etherGroups 5 }
END
5. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
Flick, et. al. Expires February 1999 [Page 40]
Internet Draft Ethernet-Like MIB August 1998
this standard. Please address the information to the IETF Executive
Director.
6. Acknowledgements
This document was produced by the 802.3 Hub MIB Working Group.
This document is based on the Proposed Standard Ethernet MIB, RFC
2358 [26], edited by John Flick of Hewlett-Packard and Jeffrey
Johnson of RedBack Networks and produced by the Ethernet Interfaces
and Hub MIB Working Group. It extends that document by providing
support for full-duplex Ethernet interfaces as outlined in [18] and
1000 Mb/sec Ethernet interfaces as outlined in [19].
RFC 2358, in turn, is almost completely based on both the Standard
Ethernet MIB, RFC 1643 [24], and the Proposed Standard Ethernet MIB
using the SNMPv2 SMI, RFC 1650 [25], both of which were edited by
Frank Kastenholz of FTP Software and produced by the Ethernet MIB
Working Group. RFC 2358 extends those documents by providing support
for 100 Mb/sec ethernet interfaces as outlined in [17].
RFC 1643 and RFC 1650, in turn, are based on the Draft Standard
Ethernet MIB, RFC 1398 [23], also edited by Frank Kastenholz and
produced by the Ethernet MIB Working Group.
RFC 1398, in turn, is based on the Proposed Standard Ethernet MIB,
RFC 1284 [21], which was edited by John Cook of Chipcom and produced
by the Transmission MIB Working Group. The Ethernet MIB Working
Group gathered implementation experience of the variables specified
in RFC 1284, documented that experience in RFC 1369 [22], and used
that information to develop this revised MIB.
RFC 1284, in turn, is based on a document written by Frank
Kastenholz, then of Interlan, entitled IEEE 802.3 Layer Management
Draft M compatible MIB for TCP/IP Networks [20]. This document was
modestly reworked, initially by the SNMP Working Group, and then by
the Transmission Working Group, to reflect the current conventions
for defining objects for MIB interfaces. James Davin, of the MIT
Laboratory for Computer Science, and Keith McCloghrie of Hughes LAN
Systems, contributed to later drafts of this memo. Marshall Rose of
Performance Systems International, Inc. converted the document into
RFC 1212 [3] concise format. Anil Rijsinghani of DEC contributed text
that more adequately describes the TDR test. Thanks to Frank
Kastenholz of Interlan and Louis Steinberg of IBM for their
experimentation.
Flick, et. al. Expires February 1999 [Page 41]
Internet Draft Ethernet-Like MIB August 1998
7. References
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2271, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research,
January 1998
[2] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16,
RFC 1155, Performance Systems International, Hughes LAN Systems,
May 1990
[3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16,
RFC 1212, Performance Systems International, Hughes LAN Systems,
March 1991
[4] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, Performance Systems International, March 1991
[5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Structure of Management Information for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1902, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
Conventions for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1903, SNMP Research, Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International
Network Services, January 1996.
[7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Conformance Statements for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1904, SNMP Research, Inc.,
Cisco Systems, Inc., Dover Beach Consulting, Inc., International
Network Services, January 1996.
[8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, SNMP Research,
Performance Systems International, Performance Systems
International, MIT Laboratory for Computer Science, May 1990.
[9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, SNMP
Research, Inc., Cisco Systems, Inc., Dover Beach Consulting,
Inc., International Network Services, January 1996.
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
Flick, et. al. Expires February 1999 [Page 42]
Internet Draft Ethernet-Like MIB August 1998
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc.,
Cisco Systems, Inc., Dover Beach Consulting, Inc., International
Network Services, January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2272, SNMP Research, Inc., Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research,
January 1998.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol
(SNMPv3)", RFC 2274, IBM T. J. Watson Research, January 1998.
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1905, SNMP Research, Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International
Network Services, January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2273, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, January 1998
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2275, IBM T. J. Watson Research, BMC Software,
Inc., Cisco Systems, Inc., January 1998
[16] International Standard ISO/IEC 8802-3: 1996(E), (ANSI/IEEE Std
802.3, 1996 Edition), "Information technology -
Telecommunications and information exchange between systems -
Local and metropolitan area networks - Specific requirements -
Part 3: Carrier sense multiple access with collision detection
(CSMA/CD) access method and physical layer specifications", July
1996.
[17] IEEE, IEEE Std 802.3u-1995, "Media Access Control (MAC)
Parameters, Physical Layer, Medium Attachment Units, and
Repeater for 100Mb/s Operation, Type 100BASE-T", Supplement to
ISO/IEC 8802-3: 1993 (ANSI/IEEE Std 802.3, 1993 Edition),
October 1995.
[18] IEEE, IEEE Std 802.3x-1997 and IEEE Std 802.3y-1997,
"Specification for 802.3 Full Duplex Operation and Physical
Layer Specification for 100Mbit/s Operation on Two Pairs of
Category 3 or Better Balanced Twisted Pair Cable (100BASE-T2)",
Flick, et. al. Expires February 1999 [Page 43]
Internet Draft Ethernet-Like MIB August 1998
Supplement to ISO/IEC 8802-3: 1996 (ANSI/IEEE Std 802.3, 1996
Edition), November 1997.
[19] IEEE, IEEE Draft 802.3z/D4.2, "Media Access Control (MAC)
Parameters, Physical Layer, Repeater and Management Parameters
for 1000 Mb/s Operation", Supplement to ISO/IEC 8802-3: 1996
(ANSI/IEEE Std 802.3, 1996 Edition), March 1998.
[20] Kastenholz, F., "IEEE 802.3 Layer Management Draft compatible
MIB for TCP/IP Networks", electronic mail message to mib-
wg@nnsc.nsf.net, 9 June 1989.
[21] Cook, J., "Definitions of Managed Objects for Ethernet-Like
Interface Types", RFC 1284, Chipcom Corporation, December 1991.
[22] Kastenholz, F., "Implementation Notes and Experience for The
Internet Ethernet MIB", RFC 1369, FTP Software, October 1992.
[23] Kastenholz, F., "Definitions of Managed Objects for the
Ethernet-like Interface Types", RFC 1398, FTP Software, Inc.,
January 1993.
[24] Kastenholz, F., "Definitions of Managed Objects for the
Ethernet-like Interface Types", STD 50, RFC 1643, FTP Software,
Inc., July 1994.
[25] Kastenholz, F., "Definitions of Managed Objects for the
Ethernet-like Interface Types using SMIv2", RFC 1650,
FTP Software, Inc., August 1994.
[26] Flick, J., and J. Johnson, "Definitions of Managed Objects
for the Ethernet-like Interface Types", RFC 2358,
Hewlett-Packard Company, RedBack Networks, June 1998.
[27] McCloghrie, K., and M. Rose, Editors, "Management Information
Base for Network Management of TCP/IP-based internets: MIB-II",
STD 17, RFC 1213, March 1991.
[28] McCloghrie, K., and F. Kastenholz, "The Interfaces Group MIB
using SMIv2", RFC 2233, Cisco Systems, FTP Software,
November 1997.
[29] Bradner, S., "Key words for use in RFCs to Indicate
Requirements Levels", BCP 14, RFC 2119, March 1997.
[30] deGraaf, K., Romascanu, D., McMaster, D., McCloghrie, K., and
S. Roberts, "Definitions of Managed Objects for IEEE 802.3
Medium Attachment Units (MAUs) using SMIv2", RFC 2239,
Flick, et. al. Expires February 1999 [Page 44]
Internet Draft Ethernet-Like MIB August 1998
3Com Corporation, Madge Networks (Israel) Ltd., Cisco Systems
Inc., Cisco Systems Inc., Farallon Computing Inc., November
1997.
8. Security Considerations
There are no management objects defined in this MIB that have a MAX-
ACCESS clause of read-write and/or read-create. So, if this MIB is
implemented correctly, then there is no risk that an intruder can
alter or create any management objects of this MIB via direct SNMP
SET operations.
There are a number of managed objects in this MIB that may be
considered to contain sensitive information. In particular, the
dot3StatsEtherChipSet object may be considered sensitive in many
environments, since it would allow an intruder to obtain information
about which vendor's equipment is in use on the network.
Therefore, it may be important in some environments to control read
access to these objects and possibly to even encrypt the values of
these object when sending them over the network via SNMP. Not all
versions of SNMP provide features for such a secure environment.
SNMPv1 by itself is such an insecure environment. Even if the
network itself is secure (for example by using IPSec), even then,
there is no control as to who on the secure network is allowed to
access and GET (read) the objects in this MIB.
It is recommended that the implementors consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2274 [12] and the View-based
Access Control Model RFC 2275 [15] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to those objects only to those principals
(users) that have legitimate rights to access them.
9. Author's Addresses
John Flick
Hewlett-Packard Company
8000 Foothills Blvd. M/S 5556
Roseville, CA 95747-5556
Phone: +1 916 785 4018
Flick, et. al. Expires February 1999 [Page 45]
Internet Draft Ethernet-Like MIB August 1998
Email: johnf@rose.hp.com
Jeffrey Johnson
RedBack Networks
2570 North First Street, Suite 410
San Jose, CA, 95131, USA
Phone: +1 408 571 2699
EMail: jeff@redbacknetworks.com
A. Change Log
A.1. Changes since RFC 2358
This section enumerates changes made to RFC 2358 to produce this
document.
(1) Section 2 has been replaced with the current SNMP
Management Framework boilerplate.
(2) The ifMtu mapping has been clarified.
(3) The relationship between the IEEE 802.3 octet counters
and the IF-MIB octet counters has been clarified.
(4) REFERENCE clauses have been updated to reflect the
actual IEEE 802.3 managed object that each MIB object
is based on.
(5) The following object DESCRIPTION clauses have been
updated to reflect that they do not increment in
full-duplex mode: dot3StatsSingleCollisionFrames,
dot3StatsMultipleCollisionFrames, dot3StatsSQETestErrors,
dot3StatsDeferredTransmissions, dot3StatsLateCollisions,
dot3StatsExcessiveCollisions, dot3StatsCarrierSenseErrors,
dot3CollFrequencies.
(6) The following object DESCRIPTION clauses have been
updated to reflect behaviour on full-duplex and
1000 Mb/s interfaces: dot3StatsAlignmentErrors,
dot3StatsFCSErrors, dot3StatsSQETestErrors,
dot3StatsLateCollisions, dot3StatsSymbolErrors.
(7) A new table, dot3ControlTable, has been added.
Flick, et. al. Expires February 1999 [Page 46]
Internet Draft Ethernet-Like MIB August 1998
(8) Two new conformance groups, etherControlGroup and
etherControlPauseGroup, have been added.
A.2. Changes between RFC 1650 and RFC 2358
This section enumerates changes made to RFC 1650 to produce RFC 2358.
(1) The MODULE-IDENTITY has been updated to reflect the changes
in the MIB.
(2) A new object, dot3StatsSymbolErrors, has been added.
(3) The definition of the object dot3StatsIndex has been
converted to use the SMIv2 OBJECT-TYPE macro.
(4) A new conformance group, etherStats100MbsGroup, has been
added.
(5) A new compliance statement, ether100MbsCompliance, has
been added.
(6) The Acknowledgements were extended to provide a more
complete history of the origin of this document.
(7) The discussion of ifType has been expanded.
(8) A section on mapping of Interfaces MIB objects has
been added.
(9) A section defining the relationship of this MIB to
the MAU MIB has been added.
(10) A section on the mapping of IEEE 802.3 managed objects
to this MIB and the Interfaces MIB has been added.
(11) Converted the dot3Tests, dot3Errors, and dot3ChipSets
OIDs to use the OBJECT-IDENTITY macro.
(12) Added to the list of registered dot3ChipSets.
(13) An intellectual property notice and copyright notice
were added, as required by RFC 2026.
B. Full Copyright Statement
This document and translations of it may be copied and furnished to
Flick, et. al. Expires February 1999 [Page 47]
Internet Draft Ethernet-Like MIB August 1998
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Flick, et. al. Expires February 1999 [Page 48]
