Network Working Group L. Wang
Internet-Draft Individual
Intended status: Standards Track H. Ananthakrishnan
Expires: April 20, 2016 Packet Design
M. Chen
Huawei
A. Dass
S. Kini
Ericsson
N. Bahadur
Bracket Computing
October 18, 2015
A YANG Data Model for Routing Information Base (RIB)
draft-ietf-i2rs-rib-data-model-02
Abstract
This document defines a YANG data model for Routing Information Base
(RIB) that aligns with the I2RS RIB information model.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 20, 2016.
Wang, et al. Expires April 20, 2016 [Page 1]
Internet-Draft RIB DM October 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Definitions and Acronyms . . . . . . . . . . . . . . . . 3
1.2. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 3
2. Model Structure . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. RIB Capability . . . . . . . . . . . . . . . . . . . . . 7
2.2. Routing Instance and Rib . . . . . . . . . . . . . . . . 7
2.3. Route . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4. Nexthop . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5. RPC Operations . . . . . . . . . . . . . . . . . . . . . 14
2.6. Notifications . . . . . . . . . . . . . . . . . . . . . . 16
3. YANG Modules . . . . . . . . . . . . . . . . . . . . . . . . 18
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 58
5. Security Considerations . . . . . . . . . . . . . . . . . . . 58
6. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 58
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.1. Normative References . . . . . . . . . . . . . . . . . . 59
7.2. Informative References . . . . . . . . . . . . . . . . . 59
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 59
1. Introduction
The Interface to the Routing System (I2RS)
[I-D.ietf-i2rs-architecture] provides read and write access to the
information and state within the routing process that exists inside
the routing elements, this is achieved via the protocol message
exchange between I2RS clients and I2RS agents associated with the
routing system. One of the functions of I2RS is to read and write
data of Routing Information Base (RIB).
[I-D.ietf-i2rs-usecase-reqs-summary] introduces a set of RIB use
cases and the RIB information model is defined in
[I-D.ietf-i2rs-rib-info-model].
Wang, et al. Expires April 20, 2016 [Page 2]
Internet-Draft RIB DM October 2015
This document defines a YANG [RFC6020][RFC6991] data model for the
RIB that satisfies the RIB use cases and aligns with the RIB
information model.
1.1. Definitions and Acronyms
RIB: Routing Information Base
Information Model (IM): An abstract model of a conceptual domain,
independent of a specific implementation or data representation.
1.2. Tree Diagrams
A simplified graphical representation of the data model is used in
this document. The meaning of the symbols in these diagrams is as
follows:
o Brackets "[" and "]" enclose list keys.
o Abbreviations before data node names: "rw" means configuration
(read-write) and "ro" state data (read-only).
o Symbols after data node names: "?" means an optional node and "*"
denotes a "list" and "leaf-list".
o Parentheses enclose choice and case nodes, and case nodes are also
marked with a colon (":").
o Ellipsis ("...") stands for contents of subtrees that are not
shown.
2. Model Structure
The following figure shows an overview of structure tree of the i2rs-
rib module. To give a whole view of the structure tree, some details
of the tree are omitted. The detail are introduced in the following
sub-sections.
module: i2rs-rib
+--rw routing-instance
+--rw name string
+--rw interface-list* [name]
| +--rw name if:interface-ref
+--rw router-id? yang:dotted-quad
+--rw lookup-limit? uint8
+--rw rib-list* [name]
+--rw name string
+--rw rib-family rib-family-def
Wang, et al. Expires April 20, 2016 [Page 3]
Internet-Draft RIB DM October 2015
+--rw enable-ip-rpf-check? boolean
+--rw route-list* [route-index]
+--rw route-index uint64
+--rw route-type route-type-def
+--rw match
| +--rw (rib-route-type)?
| +--:(ipv4)
| | ...
| +--:(ipv6)
| | ...
| +--:(mpls-route)
| | ...
| +--:(mac-route)
| | ...
| +--:(interface-route)
| ...
+--rw nexthop
| +--rw nexthop-id uint32
| +--rw sharing-flag boolean
| +--rw (nexthop-type)?
| +--:(nexthop-base)
| | ...
| +--:(nexthop-chain) {nexthop-chain}?
| | ...
| +--:(nexthop-protection) {nexthop-protection}?
| | ...
| +--:(nexthop-load-balance) {nexthop-load-balance}?
| | ...
| +--:(nexthop-replicates) {nexthop-replicates}?
| ...
+--rw route-statistic
| ...
+--rw route-attributes
| ...
+--rw route-vendor-attributes
rpcs:
+---x rib-add
| +--ro input
| | +--ro rib-name string
| | +--ro rib-family rib-family-def
| | +--ro enable-ip-rpf-check? boolean
| +--ro output
| +--ro result boolean
+---x rib-delete
| +--ro input
| | +--ro rib-name string
| +--ro output
| +--ro result boolean
Wang, et al. Expires April 20, 2016 [Page 4]
Internet-Draft RIB DM October 2015
+---x route-add
| +--ro input
| | +--ro rib-name string
| | +--ro routes
| | +--ro route-list* [route-index]
| | ...
| +--ro output
| +--ro result boolean
+---x route-delete
| +--ro input
| | +--ro rib-name string
| | +--ro routes
| | +--ro route-list* [route-index]
| | ...
| +--ro output
| +--ro result boolean
+---x route-update
| +--ro input
| | +--ro rib-name string
| | +--ro (match-conditions)?
| | +--:(match-route-prefix)
| | | ...
| | +--:(match-route-attributes)
| | | ...
| | +--:(match-nexthop)
| | ...
| +--ro output
| +--ro result boolean
+---x nh-add
| +--ro input
| | +--ro rib-name string
| | +--ro nexthop-id uint32
| | +--ro sharing-flag boolean
| | +--ro (nexthop-type)?
| | +--:(nexthop-base)
| | | ...
| | +--:(nexthop-chain) {nexthop-chain}?
| | | ...
| | +--:(nexthop-protection) {nexthop-protection}?
| | | ...
| | +--:(nexthop-load-balance) {nexthop-load-balance}?
| | | ...
| | +--:(nexthop-replicates) {nexthop-replicates}?
| | ...
| +--ro output
| +--ro result boolean
| +--ro nexthop-id uint32
+---x nh-delete
Wang, et al. Expires April 20, 2016 [Page 5]
Internet-Draft RIB DM October 2015
+--ro input
| +--ro rib-name string
| +--ro (nexthop-context-or-id)?
| +--:(nexthop-context)
| | ...
| +--:(nexthop-identifier)
| +--ro nexthop-identifer uint32
+--ro output
+--ro result boolean
notifications:
+---n nexthop-resolution-status-change
| +--ro nexthop
| | +--ro nexthop-id uint32
| | +--ro sharing-flag boolean
| | +--ro (nexthop-type)?
| | +--:(nexthop-base)
| | | ...
| | +--:(nexthop-chain) {nexthop-chain}?
| | | ...
| | +--:(nexthop-protection) {nexthop-protection}?
| | | ...
| | +--:(nexthop-load-balance) {nexthop-load-balance}?
| | | ...
| | +--:(nexthop-replicates) {nexthop-replicates}?
| | ...
| +--ro nexthop-state nexthop-state-def
+---n route-change
+--ro rib-name string
+--ro rib-family rib-family-def
+--ro route-index uint64
+--ro route-type route-type-def
+--ro match
| +--ro (rib-route-type)?
| +--:(ipv4)
| | ...
| +--:(ipv6)
| | ...
| +--:(mpls-route)
| | ...
| +--:(mac-route)
| | ...
| +--:(interface-route)
| ...
+--ro route-installed-state route-installed-state-def
+--ro route-state route-state-def
+--ro route-reason route-reason-def
Figure 1: Overview of I2RS Rib Module Structure
Wang, et al. Expires April 20, 2016 [Page 6]
Internet-Draft RIB DM October 2015
2.1. RIB Capability
RIB capability negotiation is very important because not all of the
hardware will be able to support all kinds of nexthops and there
should be a limitation on how many levels of lookup can be
practically performed. Therefore, a RIB data model MUST specify a
way for an external entity to learn about the functional capabilities
of a network device.
At the same time, nexthop chains can be used to specify multiple
headers over a packet, before that particular packet is forwarded.
Not every network device will be able to support all kinds of nexthop
chains along with the arbitrary number of headers which are chained
together. The RIB data model MUST provide a way to expose the
nexthop chaining capability supported by a given network device.
This module uses the feature and if-feature statements to achieve
above capability negotiation.
2.2. Routing Instance and Rib
A routing instance, in the context of the RIB information model, is a
collection of RIBs, interfaces, and routing protocol parameters. A
routing instance creates a logical slice of the router and can allow
multiple different logical slices; across a set of routers; to
communicate with each other. And the routing protocol parameters
control the information available in the RIBs. More detail about
routing instance can be found in Section 2.2 of
[I-D.ietf-i2rs-rib-info-model].
As described in [I-D.ietf-i2rs-rib-info-model], there will be
multiple routing instances for a router. At the same time, for a
routing instance, there would be multiple RIBs as well. Therefore,
this model uses "list" to express the RIBs. The structure tree is
shown as following figure.
Wang, et al. Expires April 20, 2016 [Page 7]
Internet-Draft RIB DM October 2015
+--rw routing-instance
+--rw name string
+--rw interface-list* [name]
| +--rw name if:interface-ref
+--rw router-id? yang:dotted-quad
+--rw lookup-limit? uint8
+--rw rib-list* [name]
+--rw name string
+--rw rib-family rib-family-def
+--rw enable-ip-rpf-check? boolean
+--rw route-list* [route-index]
... (refer to Sec.2.3)
Figure 2: Routing Instance Stuture
2.3. Route
A route is essentially a match condition and an action following that
match. The match condition specifies the kind of route (e.g., IPv4,
MPLS, MAC, Interface etc.) and the set of fields to match on.
According to the definition in [I-D.ietf-i2rs-rib-info-model], a
route MUST associate with the following attributes:
o ROUTE_PREFERENCE: See Section 2.3 of
[I-D.ietf-i2rs-rib-info-model].
o ACTIVE: Indicates whether a route is fully resolved and is a
candidate for selection.
o INSTALLED: Indicates whether the route got installed in the FIB.
In addition, a route can associate with one or more optional route
attributes(e.g., route-vendor-attributes).
For a RIB, there will have a number of routes, so the routes are
expressed as a list under the rib list.
Wang, et al. Expires April 20, 2016 [Page 8]
Internet-Draft RIB DM October 2015
+--rw route-list* [route-index]
+--rw route-index uint64
+--rw route-type route-type-def
+--rw match
| +--rw (rib-route-type)?
| +--:(ipv4)
| | +--rw ipv4
| | +--rw ipv4-route-type match-ip-route-type-def
| | +--rw (match-ip-route-type)?
| | +--:(dest-ipv4-address)
| | | ...
| | +--:(src-ipv4-address)
| | | ...
| | +--:(dest-src-ipv4-address)
| | ...
| +--:(ipv6)
| | +--rw ipv6
| | +--rw ipv6-route-type match-ip-route-type-def
| | +--rw (match-ip-route-type)?
| | +--:(dest-ipv6-address)
| | | ...
| | +--:(src-ipv6-address)
| | | ...
| | +--:(dest-src-ipv6-address)
| | ...
| +--:(mpls-route)
| | +--rw mpls-label uint32
| +--:(mac-route)
| | +--rw mac-address uint32
| +--:(interface-route)
| +--rw interface-identifier if:interface-ref
+--rw nexthop
| ...(refer to Sec.2.4)
Figure 3: Routes Structure
2.4. Nexthop
A nexthop represents an object resulting from a route lookup. As
illustrated in Section 2.4 of [I-D.ietf-i2rs-rib-info-model], to
support various of use cases (e.g., load balance, protection,
multicast or the combination of them), the nexthop is modelled as a
multi-level structure and supports recursion. The first level of the
nexthop includes the following four types:
o Base: The "base" nexthop itself is a hierarchical structure, it is
the base of all other nexthop types. The first level of the base
nexthop includes special-nexthop and nexthop-chain. The nexthop-
Wang, et al. Expires April 20, 2016 [Page 9]
Internet-Draft RIB DM October 2015
chain can have one or more nexthop chain members, each member is
one of the four types (as listed below) of specific nexthop.
Other first level nexthop (e.g., load-balance, protection and
replicate) will finally be iterated to a "base" nexthop.
* nexthop-id
* egress-interface
* logical-tunnel
* tunnel-encap
o Load-balance: Designed for load-balance case where it normally
will have multiple weighted nexthops.
o Protection: Designed for protection scenario where it normally
will have primary and standby nexthop.
o Replicate: Designed for multiple destinations forwarding.
The structure tree of nexthop is shown in the following figures.
Wang, et al. Expires April 20, 2016 [Page 10]
Internet-Draft RIB DM October 2015
+--rw nexthop
| +--rw nexthop-id uint32
| +--rw sharing-flag boolean
| +--rw (nexthop-type)?
| +--:(nexthop-base)
| | ...(refer to Figure 5)
| +--:(nexthop-chain) {nexthop-chain}?
| | +--rw nexthop-chain
| | +--rw nexthop-chain* [nexthop-chain-member-id]
| | +--rw nexthop-chain-member-id uint32
| +--:(nexthop-protection) {nexthop-protection}?
| | +--rw nexthop-protection
| | +--rw nexthop-protection-list* [...-member-id]
| | +--rw nexthop-protection-member-id uint32
| | +--rw nexthop-preference nexthop-preference-def
| +--:(nexthop-load-balance) {nexthop-load-balance}?
| | +--rw nexthop-lb
| | +--rw nexthop-lbs* [nexthop-lbs-member-id]
| | +--rw nexthop-lbs-member-id uint32
| | +--rw nhop-lb-weight nhop-lb-weight-def
| +--:(nexthop-replicates) {nexthop-replicates}?
| +--rw nexthop-replicates
| +--rw nexthop-replicates* [nexthop-replicates-member-id]
| +--rw nexthop-replicates-member-id uint32
Figure 4: Nexhop Structure
Figure 6 (as shown blow) is a sub-tree of nexthop, it's under the
nexthop base node.
+--:(nexthop-base)
| +--rw nexthop-base
| +--rw (nexthop-base-type)?
| +--:(special-nexthop)
| | +--rw special? special-nexthop-def
| +--:(egress-interface-nexthop)
| | +--rw outgoing-interface if:interface-ref
| +--:(ipv4-address-nexthop)
| | +--rw ipv4-address inet:ipv4-address
| +--:(ipv6-address-nexthop)
| | +--rw ipv6-address inet:ipv6-address
| +--:(egress-interface-ipv4-nexthop)
| | +--rw egress-interface-ipv4-address
| | +--rw outgoing-interface if:interface-ref
| | +--rw ipv4-address inet:ipv4-address
| +--:(egress-interface-ipv6-nexthop)
| | +--rw egress-interface-ipv6-address
| | +--rw outgoing-interface if:interface-ref
Wang, et al. Expires April 20, 2016 [Page 11]
Internet-Draft RIB DM October 2015
| | +--rw ipv6-address inet:ipv6-address
| +--:(egress-interface-mac-nexthop)
| | +--rw egress-interface-mac-address
| | +--rw outgoing-interface if:interface-ref
| | +--rw ieee-mac-address uint32
| +--:(tunnel-encap-nexthop) {nexthop-tunnel}?
| | +--rw tunnel-encap
| | +--rw (tunnel-type)?
| | +--:(ipv4) {ipv4-tunnel}?
| | | +--rw source-ipv4-address inet:ipv4-address
| | | +--rw destination-ipv4-address inet:ipv4-address
| | | +--rw protocol uint8
| | | +--rw ttl? uint8
| | | +--rw dscp? uint8
| | +--:(ipv6) {ipv6-tunnel}?
| | | +--rw source-ipv6-address inet:ipv6-address
| | | +--rw destination-ipv6-address inet:ipv6-address
| | | +--rw next-header uint8
| | | +--rw traffic-class? uint8
| | | +--rw flow-label? uint16
| | | +--rw hop-limit? uint8
| | +--:(mpls) {mpls-tunnel}?
| | | +--rw (mpls-action-type)?
| | | +--:(mpls-push)
| | | | +--rw mpls-push boolean
| | | | +--rw mpls-label uint32
| | | | +--rw s-bit? boolean
| | | | +--rw tc-value? uint8
| | | | +--rw ttl-value? uint8
| | | +--:(mpls-swap)
| | | +--rw mpls-swap boolean
| | | +--rw mpls-in-label uint32
| | | +--rw mpls-out-label uint32
| | | +--rw ttl-action? ttl-action-def
| | +--:(gre) {gre-tunnel}?
| | | +--rw gre-ip-destination inet:ipv4-address
| | | +--rw gre-protocol-type inet:ipv4-address
| | | +--rw gre-key? uint64
| | +--:(nvgre) {nvgre-tunnel}?
| | | +--rw (nvgre-type)?
| | | | +--:(ipv4)
| | | | | +--rw src-ipv4-address inet:ipv4-address
| | | | | +--rw dest-ipv4-address inet:ipv4-address
| | | | | +--rw protocol uint8
| | | | | +--rw ttl? uint8
| | | | | +--rw dscp? uint8
| | | | +--:(ipv6)
| | | | +--rw source-ipv6-address inet:ipv6-address
Wang, et al. Expires April 20, 2016 [Page 12]
Internet-Draft RIB DM October 2015
| | | | +--rw dest-ipv6-address inet:ipv6-address
| | | | +--rw next-header uint8
| | | | +--rw traffic-class? uint8
| | | | +--rw flow-label? uint16
| | | | +--rw hop-limit? uint8
| | | +--rw virtual-subnet-id uint32
| | | +--rw flow-id? uint16
| | +--:(vxlan) {vxlan-tunnel}?
| | +--rw (vxlan-type)?
| | | +--:(ipv4)
| | | | +--rw src-ipv4-address inet:ipv4-address
| | | | +--rw dest-ipv4-address inet:ipv4-address
| | | | +--rw protocol uint8
| | | | +--rw ttl? uint8
| | | | +--rw dscp? uint8
| | | +--:(ipv6)
| | | +--rw src-ipv6-address inet:ipv6-address
| | | +--rw dest-ipv6-address inet:ipv6-address
| | | +--rw next-header uint8
| | | +--rw traffic-class? uint8
| | | +--rw flow-label? uint16
| | | +--rw hop-limit? uint8
| | +--rw vxlan-identifier? uint32
| +--:(tunnel-decap-nexthp) {nexthop-tunnel}?
| | +--rw tunnel-decap
| | +--rw (tunnel-type)?
| | +--:(ipv4) {ipv4-tunnel}?
| | | +--rw ipv4-decap
| | | +--rw ipv4-decap boolean
| | | +--rw ttl-action? ttl-action-def
| | +--:(ipv6) {ipv6-tunnel}?
| | | +--rw ipv6-decap
| | | +--rw ipv6-decap boolean
| | | +--rw hop-limit-action? hop-limit-action-def
| | +--:(mpls) {mpls-tunnel}?
| | +--rw mpls-pop
| | +--rw mpls-pop boolean
| | +--rw ttl-action? ttl-action-def
| +--:(logical-tunnel-nexthop) {nexthop-tunnel}?
| | +--rw logical-tunnel
| | +--rw tunnel-type tunnel-type-def
| | +--rw tunnel-name string
| +--:(rib-name-nexthop)
| +--rw rib-name? string
Figure 5: Nexthop Base Structure
Wang, et al. Expires April 20, 2016 [Page 13]
Internet-Draft RIB DM October 2015
2.5. RPC Operations
This module defines the following RPC operations:
o rib-add: It is defined to add a rib to a routing instance. A name
of the rib, address family of the rib and whether the RPF check is
enabled are passed as the input parameters. The output is the
result of the add operation: 1 means success, and 0 means failed.
o rib-delete: It is defined to delete a rib from a routing instance.
When a rib is deleted, all routes installed in the rib will be
deleted. A name of the rib is passed as the input parameter. The
output is the result of the delete operation: 1 means success, and
0 means failed.
o route-add: It is defined to add a route or a set of routes to a
rib. A rib name, the route prefix(es), route attributes, route
vendor attributes and nexthop are passed as the input parameters.
The output is the result of the add operation: 1 means success,
and 0 means failed. Before calling the route-add rpc, it is
required to call the nh-add rpc to create and/or return the
nexthop identifier.
o route-delete: It is defined to delete a route or a set of routes
from a rib. A name of the rib and the route prefix(es) are passed
as the input parameters. The output is the result of the delete
operation: 1 means success, and 0 means failed.
o route-update: It is defined to update a route or a set of routes.
A rib name, the route prefix(es), or route attributes, or route
vendor attributes, or nexthop are passed as the input parameters.
The match conditions can be either route prefix(es), or route
attributes, or route vendor attributes, or nexthop. The update
actions include: update the nexthop, update the route attributes,
update the route vendor attributes. The output is the result of
the update operation: 1 means success, and 0 means failed.
o nh-add: It is defined to add a nexthop to a rib. A name of the
rib and a nexthop are passed as the input parameters. The network
node is required to allocate a nexhop identifier to the nexthop.
The outputs include the result of the update operation (1 means
success, and 0 means failed ) and the nexthop identifier that is
allocated to the nexthop.
o nh-delete: It is defined to delete a nexthop from a rib. A name
of a rib and a nexthop or nexthop identifier are passed as the
input parameters. The output is the result of the delete
operation: 1 means success, 0 means failed.
Wang, et al. Expires April 20, 2016 [Page 14]
Internet-Draft RIB DM October 2015
The structure tree of rpcs is showing in following figure.
rpcs:
+---x rib-add
| +--ro input
| | +--ro rib-name string
| | +--ro rib-family rib-family-def
| | +--ro enable-ip-rpf-check? boolean
| +--ro output
| +--ro result boolean
+---x rib-delete
| +--ro input
| | +--ro rib-name string
| +--ro output
| +--ro result boolean
+---x route-add
| +--ro input
| | +--ro rib-name string
| | +--ro routes
| | ...
| +--ro output
| +--ro result boolean
+---x route-delete
| +--ro input
| | +--ro rib-name string
| | +--ro routes
| | ...
| +--ro output
| +--ro result boolean
+---x route-update
| +--ro input
| | +--ro rib-name string
| | +--ro (match-conditions)?
| | +--:(match-route-prefix)
| | | ...
| | +--:(match-route-attributes)
| | | ...
| | +--:(match-vendor-route-attributes)
| | | ...
| | +--:(match-nexthop)
| | ...
| +--ro output
| +--ro result boolean
+---x nh-add
| +--ro input
| | +--ro rib-name string
| | +--ro nexthop-id uint32
| | +--ro sharing-flag boolean
Wang, et al. Expires April 20, 2016 [Page 15]
Internet-Draft RIB DM October 2015
| | +--ro (nexthop-type)?
| | ...
| +--ro output
| +--ro result boolean
| +--ro nexthop-id uint32
+---x nh-delete
+--ro input
| +--ro rib-name string
| +--ro (nexthop-context-or-id)?
| +--:(nexthop-context)
| | ...
| +--:(nexthop-identifier)
| ...
+--ro output
+--ro result boolean
Figure 6: RPCs Structure
2.6. Notifications
Asynchronous notifications are sent by the RIB manager of a network
device to an external entity when some event triggers on the network
device. A RIB data-model MUST support sending 2 kind of asynchronous
notifications.
1. Route change notification:
o Installed (Indicates whether the route got installed in the FIB) ;
o Active (Indicates whether a route is fully resolved and is a
candidate for selection) ;
o Reason - E.g. Not authorized
2. Nexthop resolution status notification
Nexthops can be fully resolved nexthops or an unresolved nexthop.
A resolved nexthop has adequate level of information to send the
outgoing packet towards the destination by forwarding it on an
interface of a directly connected neighbor.
An unresolved nexthop is something that requires the RIB manager to
determine the final resolved nexthop. For example, in a case when a
nexthop could be an IP address. The RIB manager would resolve how to
reach that IP address, e.g. by checking if that particular IP is
address reachable by regular IP forwarding or by a MPLS tunnel or by
both. If the RIB manager cannot resolve the nexthop, then the
Wang, et al. Expires April 20, 2016 [Page 16]
Internet-Draft RIB DM October 2015
nexthop remains in an unresolved state and is NOT a suitable
candidate for installation in the FIB.
The structure tree of notifications is shown in the following figure.
notifications:
+---n nexthop-resolution-status-change
| +--ro nexthop
| | +--ro nexthop-id uint32
| | +--ro sharing-flag boolean
| | +--ro (nexthop-type)?
| | +--:(nexthop-base)
| | | ...
| | +--:(nexthop-chain) {nexthop-chain}?
| | | ...
| | +--:(nexthop-protection) {nexthop-protection}?
| | | ...
| | +--:(nexthop-load-balance) {nexthop-load-balance}?
| | | ...
| | +--:(nexthop-replicates) {nexthop-replicates}?
| | ...
| +--ro nexthop-state nexthop-state-def
+---n route-change
+--ro rib-name string
+--ro rib-family rib-family-def
+--ro route-index uint64
+--ro route-type route-type-def
+--ro match
| +--ro (rib-route-type)?
| +--:(ipv4)
| | ...
| +--:(ipv6)
| | ...
| +--:(mpls-route)
| | ...
| +--:(mac-route)
| | ...
| +--:(interface-route)
| ...
+--ro route-installed-state route-installed-state-def
+--ro route-state route-state-def
+--ro route-reason route-reason-def
Figure 7: Notifications Structure
Wang, et al. Expires April 20, 2016 [Page 17]
Internet-Draft RIB DM October 2015
3. YANG Modules
//<CODE BEGINS> file "i2rs rib@2015-10-17.yang"
module i2rs-rib {
namespace "urn:ietf:params:xml:ns:yang:i2rs-rib";
// replace with iana namespace when assigned
prefix "i2rs-rib";
import ietf-inet-types {
prefix inet;
//rfc6991
}
import ietf-interfaces {
prefix "if";
}
import ietf-yang-types {
prefix yang;
}
organization
"IETF I2RS WG";
contact
"email: wang_little_star@sina.com
email: hari@packetdesign.com
email: mach.chen@huawei.com
email: amit.dass@ericsson.com
email: sriganesh.kini@ericsson.com
email: nitin_bahadur@yahoo.com";
description
"This module defines a YANG data model for
Routing Information Base (RIB) that aligns
with the I2RS RIB information model.";
revision "2015-10-17" {
description "initial revision";
reference "draft-ietf-i2rs-rib-info-model-07";
}
//Nexthhop related features
feature nexthop-tunnel {
description
"This feature means that a node support
tunnel nexhtop capability. The i2rs client
can specify a tunnel nexthop to a route.";
Wang, et al. Expires April 20, 2016 [Page 18]
Internet-Draft RIB DM October 2015
}
feature nexthop-chain {
description
"This feature means that a node support
chain nexhtop capability.";
}
feature nexthop-protection {
description
"This feature means that a node support
protection nexhtop capability.";
}
feature nexthop-replicates {
description
"This feature means that a node support
relicates nexhtop capability.";
}
feature nexthop-load-balance {
description
"This feature means that a node support
load balance nexhtop capability.";
}
//Tunnel encap related features
feature ipv4-tunnel {
description
"This feature means that a node support
IPv4 tunnel encapsulation capability.";
}
feature ipv6-tunnel {
description
"This feature means that a node support
IPv6 tunnel encapsulation capability.";
}
feature mpls-tunnel {
description
"This feature means that a node support
MPLS tunnel encapsulation capability.";
}
feature vxlan-tunnel {
description
"This feature means that a node support
VxLAN tunnel encapsulation capability.";
}
feature gre-tunnel {
Wang, et al. Expires April 20, 2016 [Page 19]
Internet-Draft RIB DM October 2015
description
"This feature means that a node support
GRE tunnel encapsulation capability.";
}
feature nvgre-tunnel {
description
"This feature means that a node support
NvGRE tunnel encapsulation capability.";
}
//Identities and Type Definitions
identity mpls-action {
description
"Base identify from which all mpls label
operations are derived.
The MPLS label stack operations include:
push - to add a new label to a label stack,
pop - to pop the top label from a label stack,
swap - to change the top label of a label
stack with new label.";
}
identity label-push {
base "mpls-action";
description
"MPLS label stack operation: push.";
}
identity label-pop {
base "mpls-action";
description
"MPLS label stack operation: pop.";
}
identity label-swap {
base "mpls-action";
description
"MPLS label stack operation: swap.";
}
typedef mpls-action-def {
type identityref {
base "mpls-action";
}
description
"MPLS action def.";
}
Wang, et al. Expires April 20, 2016 [Page 20]
Internet-Draft RIB DM October 2015
identity ttl-action {
description
"Base identify from which all TTL
actions are derived.
The tll actions include:
- ttl-no-action: do nothing regarding the TTL, or
- ttl-copy-to-inner: copy the TTL of the outer
header to inner header, or
- ttl-decrease-and-copy-to-inner: Decrease the TTL
by one and copy it to inner header.
";
}
identity ttl-no-action {
base "ttl-action";
description
"Do nothing regarding the TTL.";
}
identity ttl-copy-to-inner {
base "ttl-action";
description
"Copy the TTL of the outer header
to inner header.";
}
identity ttl-decrease-and-copy-to-inner {
base "ttl-action";
description
"Decrease TTL by one and copy the TTL
to inner header.";
}
typedef ttl-action-def {
type identityref {
base "ttl-action";
}
description
"TTL action def.";
}
identity hop-limit-action {
description
"Base identify from which all hop limit
actions are derived.";
}
identity hop-limit-no-action {
Wang, et al. Expires April 20, 2016 [Page 21]
Internet-Draft RIB DM October 2015
base "hop-limit-action";
description
"Do nothing regarding the hop limit.";
}
identity hop-limit-copy-to-inner {
base "hop-limit-action";
description
"Copy the hop limit of the outer header
to inner header.";
}
typedef hop-limit-action-def {
type identityref {
base "hop-limit-action";
}
description
"IPv6 hop limit action def.";
}
identity special-nexthop {
description
"Base identify from which all special
nexthops are derived.";
}
identity discard {
base "special-nexthop";
description
"This indicates that the network
device should drop the packet and
increment a drop counter.";
}
identity discard-with-error {
base "special-nexthop";
description
"This indicates that the network
device should drop the packet,
increment a drop counter and send
back an appropriate error message
(like ICMP error).";
}
identity receive {
base "special-nexthop";
description
"This indicates that that the traffic is
Wang, et al. Expires April 20, 2016 [Page 22]
Internet-Draft RIB DM October 2015
destined for the network device. For
example, protocol packets or OAM packets.
All locally destined traffic SHOULD be
throttled to avoid a denial of service
attack on the router's control plane. An
optional rate-limiter can be specified
to indicate how to throttle traffic
destined for the control plane.";
}
identity cos-value {
base "special-nexthop";
description
"Cos-value special nexthop.";
}
typedef special-nexthop-def {
type identityref {
base "special-nexthop";
}
description
"Special nexthop def.";
}
identity match-ip-route-type {
description
"Base identify from which all route
match types are derived.
Route match type could be:
match source, or
match destination, or
match source and destination.";
}
identity match-ip-src {
base "match-ip-route-type";
description
"Source route match type.";
}
identity match-ip-dest {
base "match-ip-route-type";
description
"Destination route match type";
}
identity match-ip-src-dest {
base "match-ip-route-type";
description
"Src and Dest route match type";
Wang, et al. Expires April 20, 2016 [Page 23]
Internet-Draft RIB DM October 2015
}
typedef match-ip-route-type-def {
type identityref {
base "match-ip-route-type";
}
description
"Route match type def.";
}
identity rib-family {
description
"Base identify from which all rib
address families are derived.";
}
identity ipv4-rib-family {
base "rib-family";
description
"IPv4 rib address family.";
}
identity ipv6-rib-family {
base "rib-family";
description
"IPv6 rib address family.";
}
identity mpls-rib-family {
base "rib-family";
description
"MPLS rib address family.";
}
identity ieee-mac-rib-family {
base "rib-family";
description
"MAC rib address family.";
}
typedef rib-family-def {
type identityref {
base "rib-family";
}
description
"Rib address family def.";
}
Wang, et al. Expires April 20, 2016 [Page 24]
Internet-Draft RIB DM October 2015
identity route-type {
description
"Base identify from which all route types
are derived.";
}
identity ipv4-route {
base "route-type";
description
"IPv4 route type.";
}
identity ipv6-route {
base "route-type";
description
"IPv6 route type.";
}
identity mpls-route {
base "route-type";
description
"MPLS route type.";
}
identity ieee-mac {
base "route-type";
description
"MAC route type.";
}
identity interface {
base "route-type";
description
"Interface route type.";
}
typedef route-type-def {
type identityref {
base "route-type";
}
description
"Route type def.";
}
identity tunnel-type {
description
"Base identify from which all tunnel
types are derived.";
Wang, et al. Expires April 20, 2016 [Page 25]
Internet-Draft RIB DM October 2015
}
identity ipv4-tunnel {
base "tunnel-type";
description
"IPv4 tunnel type";
}
identity ipv6-tunnel {
base "tunnel-type";
description
"IPv6 Tunnel type";
}
identity mpls-tunnel {
base "tunnel-type";
description
"MPLS tunnel type";
}
identity gre-tunnel {
base "tunnel-type";
description
"GRE tunnel type";
}
identity vxlan-tunnel {
base "tunnel-type";
description
"VxLAN tunnel type";
}
identity nvgre-tunnel {
base "tunnel-type";
description
"NVGRE tunnel type";
}
typedef tunnel-type-def {
type identityref {
base "tunnel-type";
}
description
"Tunnel type def.";
}
identity route-state {
description
Wang, et al. Expires April 20, 2016 [Page 26]
Internet-Draft RIB DM October 2015
"Base identify from which all route
states are derived.";
}
identity active {
base "route-state";
description
"Active state.";
}
identity inactive {
base "route-state";
description
"Inactive state.";
}
typedef route-state-def {
type identityref {
base "route-state";
}
description
"Route state def.";
}
identity nexthop-state {
description
"Base identify from which all nexthop
states are derived.";
}
identity resolved {
base "nexthop-state";
description
"Reolved nexthop state.";
}
identity unresolved {
base "nexthop-state";
description
"Unresolved nexthop state.";
}
typedef nexthop-state-def {
type identityref {
base "nexthop-state";
}
description
"Nexthop state def.";
Wang, et al. Expires April 20, 2016 [Page 27]
Internet-Draft RIB DM October 2015
}
identity route-installed-state {
description
"Base identify from which all route
installed states are derived.";
}
identity uninstalled {
base "route-installed-state";
description
"Uninstalled state.";
}
identity installed {
base "route-installed-state";
description
"Installed state.";
}
typedef route-installed-state-def {
type identityref {
base "route-installed-state";
}
description
"Route installed state def.";
}
identity route-reason {
description
"Base identify from which all route
reasons are derived.";
}
identity low-preference {
base "route-reason";
description
"Low preference";
}
identity unresolved-nexthop {
base "route-reason";
description
"Unresolved nexthop";
}
identity higher-metric {
base "route-reason";
Wang, et al. Expires April 20, 2016 [Page 28]
Internet-Draft RIB DM October 2015
description
"Higher metric";
}
typedef route-reason-def {
type identityref {
base "route-reason";
}
description
"Route reason def.";
}
typedef nexthop-preference-def {
type uint8 {
range "1..99";
}
description
"Nexthop-preference is used for protection schemes.
It is an integer value between 1 and 99. A lower
value indicates higher preference. To download a
primary/standby/tertiary group to the FIB, the
nexthops that are resolved and have two highest
preferences are selected.";
}
typedef nhop-lb-weight-def {
type uint8 {
range "1..99";
}
description
"Nhop-lb-weight is a number between 1 and 99.";
}
//Groupings
grouping route-prefix {
description
"The common attributes used for all types of route prefix.";
leaf route-index {
type uint64 ;
mandatory true;
description
"Route index.";
}
leaf route-type {
type route-type-def;
mandatory true;
description
"Route types, e.g., IPv4, IPv6, MPLS, MAC etc. route types.";
Wang, et al. Expires April 20, 2016 [Page 29]
Internet-Draft RIB DM October 2015
}
container match {
description
"The match condition specifies the
kind of route (IPv4, MPLS, etc.)
and the set of fields to match on.";
choice rib-route-type {
description
"To match a route according to rib route type.";
case ipv4 {
description
"IPv4 rib case.";
container ipv4 {
description
"IPv4 route match type.";
leaf ipv4-route-type {
type match-ip-route-type-def;
mandatory true;
description
"Route match type, it could be:
match source, or
match destination, or
match source and destination.
";
}
choice match-ip-route-type {
description
"To match a route according to match type.";
case dest-ipv4-address {
leaf dest-ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"To match an IPv4 destination address.";
}
}
case src-ipv4-address {
leaf src-ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"To match an IPv4 source address.";
}
}
case dest-src-ipv4-address {
container dest-src-ipv4-address {
description
"To match IPv4 source and destination addreses.";
Wang, et al. Expires April 20, 2016 [Page 30]
Internet-Draft RIB DM October 2015
leaf dest-ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"The IPv4 destination address of
the match condition.";
}
leaf src-ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"The IPv4 source address of
the match condition.";
}
}
}
}
}
}
case ipv6 {
description
"IPv6 rib case.";
container ipv6 {
description
"IPv6 route match type.";
leaf ipv6-route-type {
type match-ip-route-type-def;
mandatory true;
description
"Route match type, it could be:
match source, or
match destination, or
match source and destination.
";
}
choice match-ip-route-type {
description
"To match a route according to match type.";
case dest-ipv6-address {
leaf dest-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"To match an IPv6 destination address.";
}
}
case src-ipv6-address {
leaf src-ipv6-prefix {
Wang, et al. Expires April 20, 2016 [Page 31]
Internet-Draft RIB DM October 2015
type inet:ipv6-prefix;
mandatory true;
description
"To match an IPv6 source address.";
}
}
case dest-src-ipv6-address {
container dest-src-ipv6-address {
description
"To match the source and destination addreses.";
leaf dest-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"The IPv6 destination address of
the match condition.";
}
leaf src-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"The IPv6 source address of
the match condition.";
}
}
}
}
}
}
case mpls-route {
description
"MPLS rib case.";
leaf mpls-label {
type uint32 ;
mandatory true;
description
"The label used for matching.";
}
}
case mac-route {
description
"MAC rib case.";
leaf mac-address {
type uint32 ;
mandatory true;
description
"The MAC address used for matching.";
}
Wang, et al. Expires April 20, 2016 [Page 32]
Internet-Draft RIB DM October 2015
}
case interface-route {
description
"Interface rib case.";
leaf interface-identifier {
type if:interface-ref;
mandatory true;
description
"The interface used for matching.";
}
}
}
}
}
grouping route {
description
"The common attributes usesd for all types of route.";
uses route-prefix;
container nexthop {
description
"The nexthop of the route.";
uses nexthop;
}
container route-statistic {
description
"The statistic information of the route.";
leaf route-state {
type route-state-def;
config false;
description
"Indicate a route's state: Active or Inactive.";
}
leaf route-installed-state {
type route-installed-state-def;
config false;
description
"Indicate that a route's installed states:
Installed or uninstalled.";
}
leaf route-reason {
type route-reason-def;
config false;
description
"Indicate the route reason.";
}
}
container route-attributes {
Wang, et al. Expires April 20, 2016 [Page 33]
Internet-Draft RIB DM October 2015
description
"Route attributes.";
uses route-attributes;
}
container route-vendor-attributes {
description
"Route vendor attributes.";
uses route-vendor-attributes;
}
}
grouping nexthop {
description
"The nexthop structure.";
leaf nexthop-id {
type uint32;
mandatory true;
description
"The nexthop identifier of a nexthop.";
}
leaf sharing-flag {
type boolean;
mandatory true;
description
"To indicate whether a nexthop is sharable
or non-sharable.
1 - means sharable
0 - means non-sharable.";
}
choice nexthop-type {
description
"Based on nexthop type to derive the nexthop.";
case nexthop-base {
container nexthop-base {
description
"A nexthop base container.";
uses nexthop-base;
}
}
case nexthop-chain {
if-feature nexthop-chain;
container nexthop-chain {
description
"A nexthop chain container.";
list nexthop-chain {
key "nexthop-chain-member-id";
description
"A list of nexthop members of
Wang, et al. Expires April 20, 2016 [Page 34]
Internet-Draft RIB DM October 2015
a load nexthop chain.";
leaf nexthop-chain-member-id {
type uint32;
mandatory true;
description
"A nexthop identifier that points
to a nexthop chain member.
A nexthop chain member is a nexthop.";
}
}
}
}
case nexthop-protection {
if-feature nexthop-protection;
container nexthop-protection {
description
"A protection nexthop container.";
list nexthop-protection-list {
key "nexthop-protection-member-id";
description
"A list of nexthop protection
members of a load balance nexthop.";
leaf nexthop-protection-member-id {
type uint32;
mandatory true;
description
"A nexthop identifier that points
to a protection nexthop member.
A protection nexthop member is
a nexthop.";
}
leaf nexthop-preference {
type nexthop-preference-def;
mandatory true;
description
"Nexthop-preference is used for protection schemes.
It is an integer value between 1 and 99. A lower
value indicates higher preference. To download a
primary/standby/tertiary group to the FIB, the
nexthops that are resolved and have two highest
preferences are selected.";
}
}
}
}
case nexthop-load-balance {
if-feature nexthop-load-balance;
container nexthop-lb {
Wang, et al. Expires April 20, 2016 [Page 35]
Internet-Draft RIB DM October 2015
description
"A load balance nexthop container.";
list nexthop-lbs {
key "nexthop-lbs-member-id";
description
"A list of nexthop load balance
members of a load balance nexthop.";
leaf nexthop-lbs-member-id {
type uint32;
mandatory true;
description
"A nexthop identifier that points
to a load balance nexthop member.
A load balance nexthop member is
a nexthop.";
}
leaf nhop-lb-weight {
type nhop-lb-weight-def;
mandatory true;
description
"The weight of a nexthop of
the load balance nexthops.";
}
}
}
}
case nexthop-replicates {
if-feature nexthop-replicates;
container nexthop-replicates {
description
"A nexthop replicates container.";
list nexthop-replicates {
key "nexthop-replicates-member-id";
description
"A list of replicate nexthop members
that belong to the nexthop-replicates.";
leaf nexthop-replicates-member-id {
type uint32;
description
"A nexthop identifier that points
to a replicates nexthop member.
A replicates nexthop member is a nexthop.";
}
}
}
}
}
}
Wang, et al. Expires April 20, 2016 [Page 36]
Internet-Draft RIB DM October 2015
grouping nexthop-base {
description
"The base nexthop content for a route.";
choice nexthop-base-type {
description
"Based on nexthop chain type to select
relevant nexthop chain member.";
case special-nexthop {
leaf special {
type special-nexthop-def;
description
"A special nexthop.";
}
}
case egress-interface-nexthop {
leaf outgoing-interface {
type if:interface-ref;
mandatory true;
description
"The nexthop is an outgoing interface.";
}
}
case ipv4-address-nexthop {
leaf ipv4-address {
type inet:ipv4-address;
mandatory true;
description
"The nexthop is an IPv4 address.";
}
}
case ipv6-address-nexthop {
leaf ipv6-address {
type inet:ipv6-address;
mandatory true;
description
"The nexthop is an IPv6 address.";
}
}
case egress-interface-ipv4-nexthop {
container egress-interface-ipv4-address{
leaf outgoing-interface {
type if:interface-ref;
mandatory true;
description
"Name of the outgoing interface.";
}
leaf ipv4-address {
type inet:ipv4-address;
Wang, et al. Expires April 20, 2016 [Page 37]
Internet-Draft RIB DM October 2015
mandatory true;
description
"The nexthop points to an interface with
an IPv4 address.";
}
description
"Egress-interface and ip address: This can be usesd
in cases e.g.where the ip address is a link-local
address.";
}
}
case egress-interface-ipv6-nexthop {
container egress-interface-ipv6-address {
leaf outgoing-interface {
type if:interface-ref;
mandatory true;
description
"Name of the outgoing interface.";
}
leaf ipv6-address {
type inet:ipv6-address;
mandatory true;
description
"The nexthop points to an interface with
an IPv6 address.";
}
description
"Egress-interface and ip address: This can be usesd
in cases e.g.where the ip address is a link-local
address.";
}
}
case egress-interface-mac-nexthop {
container egress-interface-mac-address {
leaf outgoing-interface {
type if:interface-ref;
mandatory true;
description
"Name of the outgoing interface.";
}
leaf ieee-mac-address {
type uint32;
mandatory true;
description
"The nexthop points to an interface with
a specific mac-address.";
}
description
Wang, et al. Expires April 20, 2016 [Page 38]
Internet-Draft RIB DM October 2015
"The egress interface must be an ethernet
interface. Address resolution is not required
for this nexthop.";
}
}
case tunnel-encap-nexthop {
if-feature nexthop-tunnel;
container tunnel-encap {
uses tunnel-encap;
description
"This can be an encap representing an IP tunnel or
MPLS tunnel or others as defined in info model.
An optional egress interface can be chained to the
tunnel encap to indicate which interface to send
the packet out on. The egress interface is useful
when the network device contains Ethernet interfaces
and one needs to perform address resolution for the
IP packet.";
}
}
case tunnel-decap-nexthp {
if-feature nexthop-tunnel;
container tunnel-decap {
uses tunnel-decap;
description
"This is to specify decapsulating a tunnel header.";
}
}
case logical-tunnel-nexthop {
if-feature nexthop-tunnel;
container logical-tunnel {
uses logical-tunnel;
description
"This can be a MPLS LSP or a GRE tunnel (or others
as defined in This document), that is represented
by a unique identifier (e.g. name).";
}
}
case rib-name-nexthop {
leaf rib-name {
type string;
description
"A nexthop pointing to a rib indicates that the
route lookup needs to continue in The specified
rib. This is a way to perform chained lookups.";
}
}
}
Wang, et al. Expires April 20, 2016 [Page 39]
Internet-Draft RIB DM October 2015
}
grouping route-vendor-attributes {
description
"Route vendor attributes.";
}
grouping logical-tunnel {
description
"A logical tunnel that is identified
by a type and a tunnel name.";
leaf tunnel-type {
type tunnel-type-def;
mandatory true;
description
"A tunnel type.";
}
leaf tunnel-name {
type string;
mandatory true;
description
"A tunnel name that points to a logical tunnel.";
}
}
grouping ipv4-header {
description
"The IPv4 header encapsulation information.";
leaf source-ipv4-address {
type inet:ipv4-address;
mandatory true;
description
"The source ip address of the header.";
}
leaf destination-ipv4-address {
type inet:ipv4-address;
mandatory true;
description
"The destination ip address of the header.";
}
leaf protocol {
type uint8;
mandatory true;
description
"The protocol id of the header.";
}
leaf ttl {
type uint8;
Wang, et al. Expires April 20, 2016 [Page 40]
Internet-Draft RIB DM October 2015
description
"The TTL of the header.";
}
leaf dscp {
type uint8;
description
"The DSCP field of the header.";
}
}
grouping ipv6-header {
description
"The IPv6 header encapsulation information.";
leaf source-ipv6-address {
type inet:ipv6-address;
mandatory true;
description
"The source ip address of the header.";
}
leaf destination-ipv6-address {
type inet:ipv6-address;
mandatory true;
description
"The destination ip address of the header.";
}
leaf next-header {
type uint8;
mandatory true;
description
"The next header of the IPv6 header.";
}
leaf traffic-class {
type uint8;
description
"The traffic class value of the header.";
}
leaf flow-label {
type uint16;
description
"The flow label of the header.";
}
leaf hop-limit {
type uint8;
description
"The hop limit the header.";
}
}
Wang, et al. Expires April 20, 2016 [Page 41]
Internet-Draft RIB DM October 2015
grouping nvgre-header {
description
"The NvGRE header encapsulation information.";
choice nvgre-type {
description
"NvGRE can use eigher IPv4
or IPv6 header for encapsulation.";
case ipv4 {
uses ipv4-header;
}
case ipv6 {
uses ipv6-header;
}
}
leaf virtual-subnet-id {
type uint32;
mandatory true;
description
"The subnet identifier of the NvGRE header.";
}
leaf flow-id {
type uint16;
description
"The flow identifier of the NvGRE header.";
}
}
grouping vxlan-header {
description
"The VxLAN encapsulation header information.";
choice vxlan-type {
description
"NvGRE can use eigher IPv4
or IPv6 header for encapsulation.";
case ipv4 {
uses ipv4-header;
}
case ipv6 {
uses ipv6-header;
}
}
leaf vxlan-identifier {
type uint32;
description
"The VxLAN identifier of the VxLAN header.";
}
}
Wang, et al. Expires April 20, 2016 [Page 42]
Internet-Draft RIB DM October 2015
grouping gre-header {
description
"The GRE encapsulation header information.";
leaf gre-ip-destination {
type inet:ipv4-address;
mandatory true;
description
"The destination ip address of the GRE header.";
}
leaf gre-protocol-type {
type inet:ipv4-address;
mandatory true;
description
"The protocol type of the GRE header.";
}
leaf gre-key {
type uint64;
description
"The GRE key of the GRE header.";
}
}
grouping mpls-header {
description
"The MPLS encapsulation header information.";
choice mpls-action-type {
description
"Based on action type to perform different operation.";
case mpls-push {
leaf mpls-push {
type boolean;
mandatory true;
description
"Push a MPLS label to the label stack.";
}
leaf mpls-label {
type uint32;
mandatory true;
description
"The MPLS label to be pushed.";
}
leaf s-bit {
type boolean;
description
"The s-bit of the label to be pushed. ";
}
leaf tc-value {
type uint8;
Wang, et al. Expires April 20, 2016 [Page 43]
Internet-Draft RIB DM October 2015
description
"The traffic class value of the label to be pushed.";
}
leaf ttl-value {
type uint8;
description
"The TTL value of the label to to be pushed.";
}
}
case mpls-swap {
leaf mpls-swap {
type boolean;
mandatory true;
description
"Swap a MPLS label with another label.";
}
leaf mpls-in-label {
type uint32;
mandatory true;
description
"The in MPLS label.";
}
leaf mpls-out-label {
type uint32;
mandatory true;
description
"The out MPLS label.";
}
leaf ttl-action {
type ttl-action-def;
description
"The label ttl actions:
- No-action, or
- Copy to inner label,or
- Decrease (the in label) by 1 and
copy to the out label.";
}
}
}
}
grouping tunnel-encap{
description
"Tunnel encapsulation inforamtion.";
choice tunnel-type {
description
"Tunnel options for next-hops.";
case ipv4 {
Wang, et al. Expires April 20, 2016 [Page 44]
Internet-Draft RIB DM October 2015
if-feature ipv4-tunnel;
uses ipv4-header;
}
case ipv6 {
if-feature ipv6-tunnel;
uses ipv6-header;
}
case mpls {
if-feature mpls-tunnel;
uses mpls-header;
}
case gre {
if-feature gre-tunnel;
uses gre-header;
}
case nvgre {
if-feature nvgre-tunnel;
uses nvgre-header;
}
case vxlan {
if-feature vxlan-tunnel;
uses vxlan-header;
}
}
}
grouping tunnel-decap {
description
"Tunnel decapsulation inforamtion.";
choice tunnel-type {
description
"Tunnel options for next-hops.";
case ipv4 {
if-feature ipv4-tunnel;
container ipv4-decap {
leaf ipv4-decap {
type boolean;
mandatory true;
description
"IPv4 decap operations.";
}
leaf ttl-action {
type ttl-action-def;
description
"The ttl actions:
no-action or copy to inner header.";
}
description
Wang, et al. Expires April 20, 2016 [Page 45]
Internet-Draft RIB DM October 2015
"IPv4 decap.";
}
}
case ipv6 {
if-feature ipv6-tunnel;
container ipv6-decap {
leaf ipv6-decap {
type boolean;
mandatory true;
description
"IPv6 decap operations.";
}
leaf hop-limit-action {
type hop-limit-action-def;
description
"The hop limit actions:
no-action or copy to inner header.";
}
description
"IPv6 decap.";
}
}
case mpls {
if-feature mpls-tunnel;
container mpls-pop {
leaf mpls-pop {
type boolean;
mandatory true;
description
"Pop a MPLS label from the label stack.";
}
leaf ttl-action {
type ttl-action-def;
description
"The label ttl actions:
no-action or copy to inner label";
}
description
"MPLS decap.";
}
}
}
}
grouping route-attributes {
description
"Route attributes.";
leaf route-preference {
Wang, et al. Expires April 20, 2016 [Page 46]
Internet-Draft RIB DM October 2015
type uint32 ;
mandatory true;
description
"ROUTE_PREFERENCE: This is a numerical value that
allows for comparing routes from different
protocols. Static configuration is also
considered a protocol for the purpose of this
field. It iss also known as administrative-distance.
The lower the value, the higher the preference.";
}
leaf local-only {
type boolean ;
mandatory true;
description
"Indicate whether the attributes is local only.";
}
container address-family-route-attributes{
description
"Address family related route attributes.";
choice route-type {
description
"Address family related route attributes.";
case ip-route-attributes {
}
case mpls-route-attributes {
}
case ethernet-route-attributes {
}
}
}
}
container routing-instance {
description
"Configuration of an 'i2rs' pseudo-protocol
instance consists of a list of ribs.";
leaf name {
type string;
mandatory true;
description
"A routing instance is identified by its name,
INSTANCE_name. This MUST be unique across all
routing instances in a given network device.";
}
list interface-list {
key "name";
description
"This represents the list of interfaces associated
Wang, et al. Expires April 20, 2016 [Page 47]
Internet-Draft RIB DM October 2015
with this routing instance. The interface list helps
constrain the boundaries of packet forwarding.
Packets coming on these interfaces are directly
associated with the given routing instance. The
interface list contains a list of identifiers, with
each identifier uniquely identifying an interface.";
leaf name {
type if:interface-ref;
description
"A reference to the name of a configured
network layer interface.";
}
}
leaf router-id {
type yang:dotted-quad;
description
"Router ID - 32-bit number in the form of a dotted quad.";
}
leaf lookup-limit {
type uint8;
description
"A limit on how many levels of a lookup can be performed.";
}
list rib-list {
key "name";
description
"This is the list of RIBs associated with this routing
instance. Each routing instance can have multiple RIBs
to represent routes of different types.";
leaf name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
leaf rib-family {
type rib-family-def;
mandatory true;
description
"The address family of the rib.";
}
leaf enable-ip-rpf-check {
type boolean;
description
"Each RIB can be optionally associated with a
ENABLE_IP_RPF_CHECK attribute that enables Reverse
path forwarding (RPF) checks on all IP routes in that
RIB. Reverse path forwarding (RPF) check is used to
Wang, et al. Expires April 20, 2016 [Page 48]
Internet-Draft RIB DM October 2015
prevent spoofing and limit malicious traffic.";
}
list route-list {
key "route-index";
description
"A routes of a rib.";
uses route;
}
}
}
/*RPC Operations*/
rpc rib-add {
description
"To add a rib to a instance";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of the rib
that is to be added.";
}
leaf rib-family {
type rib-family-def;
mandatory true;
description
"The address family of the rib.";
}
leaf enable-ip-rpf-check {
type boolean;
description
"Each RIB can be optionally associated with a
ENABLE_IP_RPF_CHECK attribute that enables Reverse
path forwarding (RPF) checks on all IP routes in that
RIB. Reverse path forwarding (RPF) check is used to
prevent spoofing and limit malicious traffic.";
}
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the rib-add operation.
1 - means success;
Wang, et al. Expires April 20, 2016 [Page 49]
Internet-Draft RIB DM October 2015
0 - means falied.";
}
}
}
rpc rib-delete {
description
"To delete a rib from a routing instance,
by deleting the rib, all routes installed
in the rib will be deleted as well.";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of the rib
that is to be deleted.";
}
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the rib-delete operation.
1 - means success;
0 - means falied.";
}
}
}
rpc route-add {
description
"To add a route or a list of route to a rib";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
container routes {
description
"The routes to be added to the rib.";
list route-list {
key "route-index";
description
"Use a list to include all routes to be added.";
Wang, et al. Expires April 20, 2016 [Page 50]
Internet-Draft RIB DM October 2015
uses route-prefix;
uses route-attributes;
uses route-vendor-attributes;
uses nexthop;
}
}
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the route-add operation.
1 - means success;
0 - means falied.";
}
}
}
rpc route-delete {
description
"To delete a route or a list of route from a rib";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
container routes {
description
"The routes to be added to the rib.";
list route-list{
key "route-index";
description
"The list of routes to be deleted.";
uses route-prefix;
}
}
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the route-delete operation.
Wang, et al. Expires April 20, 2016 [Page 51]
Internet-Draft RIB DM October 2015
1 - means success;
0 - means falied.";
}
}
}
rpc route-update {
description
"To update a route or a list of route of a rib.
The inputs:
1. The match conditions, could be:
a. route prefix, or
b. route attribtes, or
c. nexthop;
2. The update parameters to be used:
a. new nexhop;
b. new route attributes;
Actions:
1. update the nexthop
2. update the route attributes
The outputs:
1 - success;
0 - failed.
";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
choice match-conditions {
description
"When conditions matched, update the routes.";
//Update routes that have the matched route prefixes
case match-route-prefix {
container input-routes {
description
"The matched routes to be updated.";
list route-list {
key "route-index";
description
"The list of routes to be updated.";
uses route-prefix;
choice update-actions-prefix {
description
"Update actions include:
Wang, et al. Expires April 20, 2016 [Page 52]
Internet-Draft RIB DM October 2015
1. update nexthop
2. update route attributes
3. update route-vendor-attributes.
";
case update-nexthop {
uses nexthop;
}
case update-route-attributes {
uses route-attributes;
}
case update-route-vendor-attributes {
uses route-vendor-attributes;
}
}
}
}
}
//Update the routes that have the matched attributes
case match-route-attributes {
container input-route-attributes {
description
"The route attributes are used for matching.";
uses route-attributes;
}
choice update-actions-attributes {
description
"Update actions include:
1. update nexthop
2. update route attributes
3. update route-vendor-attributes.
";
case update-nexthop {
uses nexthop;
}
case update-route-attributes {
uses route-attributes;
}
case update-route-vendor-attributes {
uses route-vendor-attributes;
}
}
}
//Update the routes that have the matched vendor attributes
case match-vendor-route-attributes {
container input-vendor-route-attributes {
description
"The vendor route attributes are used for matching.";
uses route-vendor-attributes;
Wang, et al. Expires April 20, 2016 [Page 53]
Internet-Draft RIB DM October 2015
}
choice update-actions-vendor-attributes {
description
"Update actions include:
1. update nexthop
2. update route attributes
3. update route-vendor-attributes.
";
case update-nexthop {
uses nexthop;
}
case update-route-attributes {
uses route-attributes;
}
case update-route-vendor-attributes {
uses route-vendor-attributes;
}
}
}
//Update the routes that have the matched nexthop
case match-nexthop {
container input-nexthop {
description
"The nexthop used for matching.";
uses nexthop;
}
choice update-actions-nexthop {
description
"Update actions include:
1. update nexthop
2. update route attributes
3. update route-vendor-attributes.
";
case update-nexthop {
uses nexthop;
}
case update-route-attributes {
uses route-attributes;
}
case update-route-vendor-attributes {
uses route-vendor-attributes;
}
}
}
}
}
Wang, et al. Expires April 20, 2016 [Page 54]
Internet-Draft RIB DM October 2015
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the route-update operation.
1 - means success;
0 - means falied.";
}
}
}
rpc nh-add {
description
"To add a nexthop to a rib.
Inputs parameters:
1. rib name
2. nexthop;
Actions:
Add the nexthop to the rib
Outputs:
1.Operation result:
1 - means success
0 - means faled;
2. nexthop identifier.";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
uses nexthop;
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the nh-add operation.
1 - means success;
0 - means falied.";
}
leaf nexthop-id {
type uint32;
mandatory true;
Wang, et al. Expires April 20, 2016 [Page 55]
Internet-Draft RIB DM October 2015
description
"A nexthop identifer that is allocated to the nexthop.";
}
}
}
rpc nh-delete {
description
"To delete a nexthop from a rib";
input {
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
choice nexthop-context-or-id {
description
"Delete a nexthop by inputing
the nexthop itself or its nexthop id.";
case nexthop-context {
uses nexthop;
}
case nexthop-identifier {
leaf nexthop-identifer {
type uint32;
mandatory true;
description
"A reference to the nexthop to be deleted.";
}
}
}
}
output {
leaf result {
type boolean ;
mandatory true;
description
"Return the result of the nh-delete operation.
1 - means success;
0 - means falied.";
}
}
}
/*Notifications*/
Wang, et al. Expires April 20, 2016 [Page 56]
Internet-Draft RIB DM October 2015
notification nexthop-resolution-status-change {
description
"Nexthop resolution status (resolved/unresolved)
notification.";
container nexthop{
description
"The nexthop.";
uses nexthop;
}
leaf nexthop-state {
type nexthop-state-def;
mandatory true;
description
"Nexthop resolution status (resolved/unresolved)
notification.";
}
}
notification route-change {
description
"Route change notification.";
leaf rib-name {
type string;
mandatory true;
description
"A reference to the name of a rib.";
}
leaf rib-family {
type rib-family-def;
mandatory true;
description
"A reference to address family of a rib.";
}
uses route-prefix;
leaf route-installed-state {
type route-installed-state-def;
mandatory true;
description
"Indicates whether the route got installed in the FIB.";
}
leaf route-state {
type route-state-def;
mandatory true;
description
"Indicates whether a route is fully resolved and
is a candidate for selection.";
}
leaf route-change-reason {
Wang, et al. Expires April 20, 2016 [Page 57]
Internet-Draft RIB DM October 2015
type route-reason-def;
mandatory true;
description
"Return the reason that causes the route change.";
}
}
}
//<CODE ENDS>
4. IANA Considerations
This document requests to register a URI in the "IETF XML registry"
[RFC3688]:
--------------------------------------------------------------------
URI: urn:ietf:params:xml:ns:yang:ietf-i2rs-rib
Registrant Contact: The IESG.XML:
N/A, the requested URI is an XML namespace.
--------------------------------------------------------------------
This document requests to register a YANG module in the "YANG Module
Names registry" [RFC6020]:
--------------------------------------------------------------------
name: ietf-i2rs-rib
namespace: urn:ietf:params:xml:ns:yang:ietf-i2rs-rib
prefix: iir
reference: RFC XXXX
--------------------------------------------------------------------
5. Security Considerations
This document introduces no extra new security threat and SHOULD
follow the security requirements as stated in
[I-D.ietf-i2rs-architecture].
6. Contributors
The following individuals also contribute to this document.
o Zekun He, Tencent Holdings Ltd
o Sujian Lu, Tencent Holdings Ltd
o Jeffery Zhang, Juniper Networks
Wang, et al. Expires April 20, 2016 [Page 58]
Internet-Draft RIB DM October 2015
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<http://www.rfc-editor.org/info/rfc3688>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<http://www.rfc-editor.org/info/rfc6020>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
<http://www.rfc-editor.org/info/rfc6991>.
7.2. Informative References
[I-D.ietf-i2rs-architecture]
Atlas, A., Halpern, J., Hares, S., Ward, D., and T.
Nadeau, "An Architecture for the Interface to the Routing
System", draft-ietf-i2rs-architecture-09 (work in
progress), March 2015.
[I-D.ietf-i2rs-rib-info-model]
Bahadur, N., Kini, S., and J. Medved, "Routing Information
Base Info Model", draft-ietf-i2rs-rib-info-model-07 (work
in progress), September 2015.
[I-D.ietf-i2rs-usecase-reqs-summary]
Hares, S. and M. Chen, "Summary of I2RS Use Case
Requirements", draft-ietf-i2rs-usecase-reqs-summary-01
(work in progress), May 2015.
Authors' Addresses
Lixing Wang
Individual
Email: wang_little_star@sina.com
Wang, et al. Expires April 20, 2016 [Page 59]
Internet-Draft RIB DM October 2015
Hariharan Ananthakrishnan
Packet Design
Email: hari@packetdesign.com
Mach(Guoyi) Chen
Huawei
Email: mach.chen@huawei.com
Amit Dass
Ericsson
Torshamnsgatan 48.
Stockholm 16480
Sweden
Email: amit.dass@ericsson.com
Sriganesh Kini
Ericsson
Email: sriganesh.kini@ericsson.com
Nitin Bahadur
Bracket Computing
Email: nitin_bahadur@yahoo.com
Wang, et al. Expires April 20, 2016 [Page 60]