IDMR Working Group Keith McCloghrie
INTERNET-DRAFT Dino Farinacci
Expires September 1997 Cisco Systems
Dave Thaler
University of Michigan
25 March 1997
Protocol Independent Multicast MIB
<draft-ietf-idmr-pim-mib-03.txt>
Status of this Memo
This document is an Internet Draft. Internet Drafts are working
documents of the Internet Engineering Task Force (IETF), its Areas, and
its Working Groups. Note that other groups may also distribute working
documents as Internet Drafts.
Internet Drafts are valid for a maximum of six months and may be
updated, replaced, or obsoleted by other documents at any time. It is
inappropriate to use Internet Drafts as reference material or to cite
them other than as a "work in progress".
1. Introduction
This memo defines an experimental portion of the Management Information
Base (MIB) for use with network management protocols in the Internet
community. In particular, it describes managed objects used for
managing the Protocol Independent Multicast (PIM) protocol [5,6,7,8].
This MIB module is applicable to IP multicast routers which implement
PIM.
Draft PIM MIB March 1997
2. Revision History
A record of changes which will be removed before publication.
25 March
(1) deprecated pimInterfaceMode, which is obsoleted by
ipMRouteInterfaceProtocol in the IP Multicast MIB.
(2) deprecated pimNeighborMode (to retain support for PIM version 1).
(3) moved pimCandidateBSRPreference to the PIM Interface Table and
renamed it pimInterfaceCBSRPreference.
(4) moved pimBSRAddress, pimBSRExpiryTime, and pimCandidateRPHoldTime
to the new PIM Component Table, to manage routers connected to
multiple PIM domains.
(5) renamed pimMessageInterval to pimJoinPruneInterval and
pimInterfaceQueryInterval to pimInterfaceHelloInterval.
(6) added pimInterfaceJoinPruneInterval.
9 June:
(1) added pimRPSetTable and pimCandidateRPTable.
(2) deprecated pimRPTable (to retain support for PIM version 1).
(3) removed pimGroupTable.
(4) added pimBSRAddress, pimBSRExpiryTime, pimCandidateBSRPreference
and pimCandidateRPHoldTime.
4 November:
(1) changed the PIM Group table to hold information common to all RPs
of a group.
(2) added the PIM RP table with each entry specific to an RP of a
group.
(3) added pimNeighborMode
Expires September 1997 [Page 2]
Draft PIM MIB March 1997
(4) modified the pimGroupTable to be indexed by pimGroupAddress and
pimGroupRP, in order to allow for multiple RPs per group.
15 July - initial version.
3. The SNMP Network Management Framework
The SNMP Network Management Framework presently consists of three major
components. They are:
o RFC 1902 [1] which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of management.
o STD 17, RFC 1213 [2] defines MIB-II, the core set of managed
objects for the Internet suite of protocols.
o RFC 1157 [3] and RFC 1905 [4] which define two versions of the
protocol used for network access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
3.1. Object Definitions
Managed objects are accessed via a virtual information store, termed the
Management Information Base or MIB. Objects in the MIB are defined
using the subset of Abstract Syntax Notation One (ASN.1) defined in the
SMI. In particular, each object type is named by an OBJECT IDENTIFIER,
an administratively assigned name. The object type together with an
object instance serves to uniquely identify a specific instantiation of
the object. For human convenience, we often use a textual string,
termed the descriptor, to refer to the object type.
4. Overview
This MIB module contains one scalar and six tables. The tables are:
(1) the PIM Interface Table which contains one row for each of the
router's PIM interfaces;
(2) the PIM Neighbor Table which contains one row for each of the
router's PIM neighbors; and
Expires September 1997 [Page 3]
Draft PIM MIB March 1997
(3) the PIM RP-Set Table which contains the PIM (version 2) information
for sets of candidate Rendezvous Points (RPs) for IP multicast
group addresses with particular address prefixes.
(4) the PIM Candidate-RP Table which contains the IP multicast groups
for which the local router is to advertise itself as a Candidate-
RP. If this table is empty, then the local router advertises
itself as a Candidate-RP for all groups.
(5) the (deprecated) PIM RP Table which contains the PIM (version 1)
information for IP multicast groups which is common to all RPs of a
group;
(6) the PIM Component Table which contains one row for each of the PIM
domains to which the router is connected.
Expires September 1997 [Page 4]
Draft PIM MIB March 1997
5. Definitions
PIM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, experimental,
Integer32, IpAddress, TimeTicks FROM SNMPv2-SMI
RowStatus FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF;
pimMIB MODULE-IDENTITY
LAST-UPDATED "9703261231Z"
ORGANIZATION "IETF IDMR Working Group."
CONTACT-INFO
" Keith McCloghrie
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
US
Phone: +1 408 526 5260
EMail: kzm@cisco.com"
DESCRIPTION
"The MIB module for management of PIM routers."
::= { experimental 61 }
pimMIBObjects OBJECT IDENTIFIER ::= { pimMIB 1 }
pim OBJECT IDENTIFIER ::= { pimMIBObjects 1 }
pimJoinPruneInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default interval at which periodic PIM-SM Join/Prune
messages are to be sent."
::= { pim 1 }
Expires September 1997 [Page 5]
Draft PIM MIB March 1997
-- The PIM Interface Table
pimInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM interfaces.
IGMP and PIM are enabled on all interfaces listed in this
table."
::= { pim 2 }
pimInterfaceEntry OBJECT-TYPE
SYNTAX PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimInterfaceTable."
INDEX { pimInterfaceIfIndex }
::= { pimInterfaceTable 1 }
PimInterfaceEntry ::= SEQUENCE {
pimInterfaceIfIndex Integer32,
pimInterfaceAddress IpAddress,
pimInterfaceNetMask IpAddress,
pimInterfaceMode INTEGER,
pimInterfaceDR IpAddress,
pimInterfaceHelloInterval Integer32,
pimInterfaceStatus RowStatus,
pimInterfaceJoinPruneInterval Integer32,
pimInterfaceCBSRPreference Integer32
}
pimInterfaceIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex value of this PIM interface."
::= { pimInterfaceEntry 1 }
pimInterfaceAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
Expires September 1997 [Page 6]
Draft PIM MIB March 1997
DESCRIPTION
"The IP address of the PIM interface."
::= { pimInterfaceEntry 2 }
pimInterfaceNetMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network mask for the IP address of the PIM interface."
::= { pimInterfaceEntry 3 }
pimInterfaceMode OBJECT-TYPE
SYNTAX INTEGER { dense(1), sparse(2) }
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The configured mode of this PIM interface."
DEFVAL { dense }
::= { pimInterfaceEntry 4 }
pimInterfaceDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Designated Router on this PIM interface. For point-
to-point interfaces, this object has the value 0.0.0.0."
::= { pimInterfaceEntry 5 }
pimInterfaceHelloInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which PIM Hello messages are transmitted
on this interface."
DEFVAL { 30 }
::= { pimInterfaceEntry 6 }
pimInterfaceStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
Expires September 1997 [Page 7]
Draft PIM MIB March 1997
DESCRIPTION
"The status of this entry. Creating the entry enables PIM
on the interface; destroying the entry disables PIM on the
interface."
::= { pimInterfaceEntry 7 }
pimInterfaceJoinPruneInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which PIM Join/Prune messages are
transmitted on this PIM interface. The default value of
this object is the pimJoinPruneInterval."
::= { pimInterfaceEntry 8 }
pimInterfaceCBSRPreference OBJECT-TYPE
SYNTAX Integer32 (-1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preference value for the local interface as a candidate
bootstrap router. The value of -1 is used to indicate that
the local interface is not a candidate BSR interface."
DEFVAL { 0 }
::= { pimInterfaceEntry 9 }
-- The PIM Neighbor Table
pimNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM neighbors."
::= { pim 3 }
pimNeighborEntry OBJECT-TYPE
SYNTAX PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimNeighborTable."
Expires September 1997 [Page 8]
Draft PIM MIB March 1997
INDEX { pimNeighborAddress }
::= { pimNeighborTable 1 }
PimNeighborEntry ::= SEQUENCE {
pimNeighborAddress IpAddress,
pimNeighborIfIndex Integer32,
pimNeighborUpTime TimeTicks,
pimNeighborExpiryTime TimeTicks,
pimNeighborMode INTEGER
}
pimNeighborAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the PIM neighbor for which this entry
contains information."
::= { pimNeighborEntry 1 }
pimNeighborIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ifIndex for the interface used to reach this
PIM neighbor."
::= { pimNeighborEntry 2 }
pimNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this PIM neighbor (last) became a neighbor
of the local router."
::= { pimNeighborEntry 3 }
pimNeighborExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before this PIM neighbor will be
aged out."
Expires September 1997 [Page 9]
Draft PIM MIB March 1997
::= { pimNeighborEntry 4 }
pimNeighborMode OBJECT-TYPE
SYNTAX INTEGER { dense(1), sparse(2) }
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The active PIM mode of this neighbor. This object is
deprecated for PIMv2 routers since all neighbors on the
interface must be either dense or sparse as determined by
the protocol running on the interface."
::= { pimNeighborEntry 5 }
-- The PIM RP Table
pimRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimRPEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The (conceptual) table listing PIM version 1 information
for the Rendezvous Points (RPs) for IP multicast groups.
This table is deprecated since its function is replaced by
the pimRPSetTable for PIM version 2."
::= { pim 5 }
pimRPEntry OBJECT-TYPE
SYNTAX PimRPEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry (conceptual row) in the pimRPTable. There is one
entry per RP address for each IP multicast group."
INDEX { pimRPGroupAddress, pimRPAddress }
::= { pimRPTable 1 }
Expires September 1997 [Page 10]
Draft PIM MIB March 1997
PimRPEntry ::= SEQUENCE {
pimRPGroupAddress IpAddress,
pimRPAddress IpAddress,
pimRPState INTEGER,
pimRPStateTimer TimeTicks,
pimRPLastChange TimeTicks,
pimRPRowStatus RowStatus
}
pimRPGroupAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The IP multicast group address for which this entry
contains information about an RP."
::= { pimRPEntry 1 }
pimRPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The IP multicast group address for which this entry
contains PIM version 1 information about an RP."
::= { pimRPEntry 2 }
pimRPState OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The state of the RP."
::= { pimRPEntry 3 }
pimRPStateTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The minimum time remaining before the next state change.
When pimRPState is up, this is the minimum time which must
expire until it can be declared down. When pimRPState is
down, this is the time until it will be declared up (in
order to retry)."
Expires September 1997 [Page 11]
Draft PIM MIB March 1997
::= { pimRPEntry 4 }
pimRPLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The value of sysUpTime at the time when the corresponding
instance of pimRPState last changed its value."
::= { pimRPEntry 5 }
pimRPRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { pimRPEntry 6 }
-- The PIM RP-Set Table
pimRPSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing PIM information for
candidate Rendezvous Points (RPs) for IP multicast groups.
When the local router is the BSR, this information is
obtained from received Candidate-RP-Advertisements. When
the local router is not the BSR, this information is
obtained from received RP-Set messages."
::= { pim 6 }
pimRPSetEntry OBJECT-TYPE
SYNTAX PimRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimRPSetTable."
INDEX { pimRPSetGroupAddress, pimRPSetGroupMask,
pimRPSetAddress }
::= { pimRPSetTable 1 }
Expires September 1997 [Page 12]
Draft PIM MIB March 1997
PimRPSetEntry ::= SEQUENCE {
pimRPSetGroupAddress IpAddress,
pimRPSetGroupMask IpAddress,
pimRPSetAddress IpAddress,
pimRPSetHoldTime Integer32,
pimRPSetExpiryTime TimeTicks
}
pimRPSetGroupAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
pimRPSetGroupMask, gives the group prefix for which this
entry contains information about the Candidate-RP."
::= { pimRPSetEntry 1 }
pimRPSetGroupMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address mask which, when combined with
pimRPSetGroupAddress, gives the group prefix for which this
entry contains information about the Candidate-RP."
::= { pimRPSetEntry 2 }
pimRPSetAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the Candidate-RP."
::= { pimRPSetEntry 3 }
pimRPSetHoldTime OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The holdtime of a Candidate-RP. If the local router is not
the BSR, this value is 0."
::= { pimRPSetEntry 4 }
Expires September 1997 [Page 13]
Draft PIM MIB March 1997
pimRPSetExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before the Candidate-RP will be
declared down. If the local router is not the BSR, this
value is 0."
::= { pimRPSetEntry 5 }
-- The PIM Candidate-RP Table
pimCandidateRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimCandidateRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the IP multicast groups for
which the local router is to advertise itself as a
Candidate-RP when the value of pimCandidateRPHoldTime is
non-zero. If this table is empty, then the local router
will advertise itself as a Candidate-RP for all groups
(providing the value of pimCandidateRPHoldTime is non-
zero)."
::= { pim 11 }
pimCandidateRPEntry OBJECT-TYPE
SYNTAX PimCandidateRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimCandidateRPTable."
INDEX { pimCandidateRPGroupAddress,
pimCandidateRPGroupMask }
::= { pimCandidateRPTable 1 }
PimCandidateRPEntry ::= SEQUENCE {
pimCandidateRPGroupAddress IpAddress,
pimCandidateRPGroupMask IpAddress,
pimCandidateRPAddress IpAddress,
pimCandidateRPRowStatus RowStatus
}
pimCandidateRPGroupAddress OBJECT-TYPE
Expires September 1997 [Page 14]
Draft PIM MIB March 1997
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
pimCandidateRPGroupMask, identifies a group prefix for which
the local router will advertise itself as a Candidate-RP."
::= { pimCandidateRPEntry 1 }
pimCandidateRPGroupMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address mask which, when combined with
pimCandidateRPGroupMask, identifies a group prefix for which
the local router will advertise itself as a Candidate-RP."
::= { pimCandidateRPEntry 2 }
pimCandidateRPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The (unicast) address of the interface which will be
advertised as a Candidate-RP."
::= { pimCandidateRPEntry 3 }
pimCandidateRPRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { pimCandidateRPEntry 4 }
Expires September 1997 [Page 15]
Draft PIM MIB March 1997
-- The PIM Component Table
pimComponentTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimComponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing objects specific to a PIM
domain. One row exists for each domain to which the router
is connected."
::= { pim 12 }
pimComponentEntry OBJECT-TYPE
SYNTAX PimComponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimComponentTable."
INDEX { pimComponentIndex }
::= { pimComponentTable 1 }
PimComponentEntry ::= SEQUENCE {
pimComponentIndex Integer32,
pimComponentBSRAddress IpAddress,
pimComponentBSRExpiryTime TimeTicks,
pimComponentCRPHoldTime Integer32,
pimComponentStatus RowStatus
}
pimComponentIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number uniquely identifying the component. Each protocol
instance connected to a separate domain should have a
different index value."
::= { pimComponentEntry 1 }
pimComponentBSRAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the bootstrap router (BSR) for the local
Expires September 1997 [Page 16]
Draft PIM MIB March 1997
PIM region."
::= { pimComponentEntry 2 }
pimComponentBSRExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before the bootstrap router in
the local domain will be declared down. For candidate BSRs,
this is the time until the component sends an RP-Set
message. For other routers, this is the time until it may
accept an RP-Set message from a lower candidate BSR."
::= { pimComponentEntry 3 }
pimComponentCRPHoldTime OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The holdtime of the component when it is a candidate RP in
the local domain. The value of 0 is used to indicate that
the local system is not a Candidate-RP."
DEFVAL { 0 }
::= { pimComponentEntry 4 }
pimComponentStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this entry. Creating the entry creates
another protocol instance; destroying the entry disables a
protocol instance."
::= { pimComponentEntry 5 }
Expires September 1997 [Page 17]
Draft PIM MIB March 1997
-- conformance information
pimMIBConformance OBJECT IDENTIFIER ::= { pimMIB 2 }
pimMIBCompliances OBJECT IDENTIFIER ::= { pimMIBConformance 1 }
pimMIBGroups OBJECT IDENTIFIER ::= { pimMIBConformance 2 }
-- compliance statements
pimV1MIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for routers running PIMv1 and
implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimV1MIBGroup }
::= { pimMIBCompliances 1 }
pimSparseV2MIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Sparse
Mode and implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimV2MIBGroup }
OBJECT pimInterfaceStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { pimMIBCompliances 2 }
pimDenseV2MIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Dense Mode
and implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimDenseV2MIBGroup }
OBJECT pimInterfaceStatus
MIN-ACCESS read-only
DESCRIPTION
Expires September 1997 [Page 18]
Draft PIM MIB March 1997
"Write access is not required."
::= { pimMIBCompliances 3 }
-- units of conformance
pimV2MIBGroup OBJECT-GROUP
OBJECTS { pimJoinPruneInterval, pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceDR, pimInterfaceHelloInterval,
pimInterfaceStatus, pimInterfaceJoinPruneInterval,
pimInterfaceCBSRPreference,
pimRPSetHoldTime, pimRPSetExpiryTime,
pimComponentBSRAddress, pimComponentBSRExpiryTime,
pimComponentCRPHoldTime, pimComponentStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM Sparse
Mode (version 2) routers."
::= { pimMIBGroups 2 }
pimDenseV2MIBGroup OBJECT-GROUP
OBJECTS { pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceDR, pimInterfaceHelloInterval,
pimInterfaceStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM Dense
Mode (version 2) routers."
::= { pimMIBGroups 5 }
pimV2CandidateRPMIBGroup OBJECT-GROUP
OBJECTS { pimCandidateRPAddress,
pimCandidateRPRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support configuration of which
groups a router is to advertise itself as a Candidate-RP."
Expires September 1997 [Page 19]
Draft PIM MIB March 1997
::= { pimMIBGroups 3 }
pimV1MIBGroup OBJECT-GROUP
OBJECTS { pimJoinPruneInterval, pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimNeighborMode,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceMode, pimInterfaceDR,
pimInterfaceHelloInterval,
pimRPState, pimRPStateTimer,
pimRPLastChange, pimRPRowStatus
}
STATUS deprecated
DESCRIPTION
"A collection of objects to support management of PIM
(version 1) routers."
::= { pimMIBGroups 4 }
END
Expires September 1997 [Page 20]
Draft PIM MIB March 1997
6. Acknowledgements
This MIB module has been updated based on feedback from the IETF's
Inter-Domain Multicast Routing (IDMR) Working Group.
7. References
[1] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
S. Waldbusser, "Structure of Management Information for version 2
of the Simple Network Management Protocol (SNMPv2)", RFC 1902,
January 1996.
[2] McCloghrie, K., and M. Rose, Editors, "Management Information Base
for Network Management of TCP/IP-based internets: MIB-II", STD 17,
RFC 1213, March 1991.
[3] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, May 1990.
[4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
S. Waldbusser, "Protocol Operations for version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1905, January 1996.
[5] Deering, S., Estrin, D., Farinacci, D., Jacobson, V., Liu, G., and
L. Wei, "Protocol Independent Multicast (PIM): Motivation and
Architecture", January 1995.
[6] Deering, S., Estrin, D., Farinacci, D., Jacobson, V., Liu, G., and
L. Wei, "Protocol Independent Multicast (PIM): Protocol
Specification", January 1995.
[7] Estrin, D., Farinacci, D., Helmy, A., Thaler, D., Deering, S.,
Handley, M., Jacobson, V., Liu, C., Sharma, P., and L. Wei,
"Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol
Specification", November 1996.
[8] Estrin, D., Farinacci, D., Jacobson, V., Liu, C., Wei, L., Sharma,
P, and Helmy, A., "Protocol Independent Multicast-Dense Mode (PIM-
DM): Protocol Specification", January 1996.
Expires September 1997 [Page 21]
Draft PIM MIB March 1997
8. Security Considerations
Security issues are not discussed in this memo.
9. Author's Address
Keith McCloghrie
cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
Phone: +1 408 526 5260
EMail: kzm@cisco.com
Dino Farinacci
cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
Phone: +1 408 526 4696
EMail: dino@cisco.com
Dave Thaler
Department of Electrical Engineering and Computer Science
University of Michigan
1301 Beal Ave.
Ann Arbor, MI 48109-2122
Phone: +1 313 763 5243
EMail: thalerd@eecs.umich.edu
Expires September 1997 [Page 22]
Draft PIM MIB March 1997
Table of Contents
1 Introduction .................................................... 1
2 Revision History ................................................ 2
3 The SNMP Network Management Framework ........................... 3
3.1 Object Definitions ............................................ 3
4 Overview ........................................................ 3
5 Definitions ..................................................... 5
6 Acknowledgements ................................................ 21
7 References ...................................................... 21
8 Security Considerations ......................................... 22
9 Author's Address ................................................ 22
Expires September 1997 [Page 23]