Network Working Group                                         L. Dunbar
Internet Draft                                                Futurewei
Intended status: Standard                                      S. Hares
Expires: October 26, 2022                      Hickory Hill Consulting
                                                               R. Raszuk
                                                 NTT Network Innovations
                                                            K. Majumdar
                                                               CommScope
                                                             Gyan Mishra
                                                                 Verizon
                                                          April 26, 2022



                    BGP UPDATE for SDWAN Edge Discovery
                  draft-ietf-idr-sdwan-edge-discovery-02

Abstract

   The document describes the encoding of BGP UPDATE messages for the
   SDWAN edge node discovery.

   In the context of this document, BGP Route Reflector (RR) is the
   component of the SDWAN Controller that receives the BGP UPDATE from
   SDWAN edges and in turns propagates the information to the intended
   peers that are authorized to communicate via the SDWAN overlay
   network.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."





xxx, et al.            Expires October 26, 2022                [Page 1]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

   This Internet-Draft will expire on Dec 25, 2022.

Copyright Notice

   Copyright (c) 2022 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document. Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.

Table of Contents


   1. Introduction...................................................3
   2. Conventions used in this document..............................3
   3. Framework of SDWAN Edge Discovery..............................5
      3.1. The Objectives of SDWAN Edge Discovery....................5
      3.2. Comparing with Pure IPsec VPN.............................5
      3.3. Client Route UPDATE and Hybrid Underlay Tunnel UPDATE.....7
      3.4. Edge Node Discovery.......................................9
   4. BGP UPDATE to Support SDWAN Segmentation......................10
      4.1. SDWAN Segmentation, SDWAN Virtual Topology and Client VPN10
      4.2. Constrained Propagation of Edge Capability...............11
   5. Client Route UPDATE...........................................12
      5.1. SDWAN VPN ID in Client Route Update......................13
      5.2. SDWAN VPN ID in Data Plane...............................13
   6. Hybrid Underlay Tunnel UPDATE.................................13
      6.1. NLRI for Hybrid Underlay Tunnel Update...................13
      6.2. SDWAN-Hybrid Tunnel Encoding.............................15
      6.3. IPsec-SA-ID Sub-TLV......................................15


Dunbar, et al.           Expires Dec 26, 2022                  [Page 2]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


         6.3.1. Encoding example #1 of using IPsec-SA-ID Sub-TLV....16
         6.3.2. Encoding Example #2 of using IPsec-SA-ID Sub-TLV....17
      6.4. Extended Port Tunnel Encapsulation Attribute Sub-TLV.....18
      6.5. Underlay Network Properties Sub-TLV......................20
   7. IPsec SA Property Sub-TLVs....................................21
      7.1. IPsec SA Nonce Sub-TLV...................................21
      7.2. IPsec Public Key Sub-TLV.................................22
      7.3. IPsec SA Proposal Sub-TLV................................23
      7.4. Simplified IPsec Security Association sub-TLV............23
      7.5. IPsec SA Encoding Examples...............................24
   8. Error & Mismatch Handling.....................................25
   9. Manageability Considerations..................................26
   10. Security Considerations......................................27
   11. IANA Considerations..........................................27
      11.1. Hybrid (SDWAN) Overlay SAFI.............................27
      11.2. Tunnel Encapsulation Attribute Type.....................27
   12. References...................................................28
      12.1. Normative References....................................28
      12.2. Informative References..................................28
   13. Acknowledgments..............................................30

1. Introduction

   [SDWAN-BGP-USAGE] illustrates how BGP [RFC4271] is used as a control
   plane for a SDWAN network. SDWAN network refers to a policy-driven
   network over multiple heterogeneous underlay networks to get better
   WAN bandwidth management, visibility, and control.

   The document describes BGP UPDATE messages for an SDWAN edge node to
   announce its properties to its RR which then propagates that
   information to the authorized peers.

2. Conventions used in this document
   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

   The following acronyms and terms are used in this document:






Dunbar, et al.           Expires Dec 26, 2022                  [Page 3]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


   Cloud DC:   Off-Premise Data Centers that usually host applications
               and workload owned by different organizations or
               tenants.

   Controller: Used interchangeably with SDWAN controller to manage
               SDWAN overlay path creation/deletion and monitor the
               path conditions between sites.

   CPE:        Customer (Edge) Premises Equipment.

   CPE-Based VPN: Virtual Private Secure network formed among CPEs.
               This is to differentiate such VPNs from most commonly
               used PE-based VPNs discussed in [RFC4364].

   MP-NLRI:    Multi-Protocol Network Layer Reachability Information
               [MP_REACH_NLRI] Path Attribute defined in RFC4760.

   SDWAN End-point:  can be the SDWAN edge node address, a WAN port
               address (logical or physical) of a SDWAN edge node, or a
               client port address.

   OnPrem:     On Premises data centers and branch offices.

   RR          Route Reflector.

   SDWAN:      Software Defined Wide Area Network. In this document,
               "SDWAN" refers to policy-driven transporting IP packets
               over multiple different underlay networks to get better
               WAN bandwidth management, visibility and control.

   SDWAN Segmentation: Segmentation is the process of dividing the
               network into logical sub-networks.

   SDWAN VPN: refers to the Client's VPN, which is like the VRF on the
               PEs of a MPLS VPN. One SDWAN client VPN can be mapped
               one or multiple SD-WAN virtual topologies. How Client
               VPN is mapped to a SDWAN virtual topology is governed by
               policies.

   SDWAN Virtual Topology: Since SDWAN can connect any nodes, whereas
               MPLS VPN connects a fixed number of PEs, one SDWAN


Dunbar, et al.           Expires Dec 26, 2022                  [Page 4]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


               Virtual Topology refers to a set of edge nodes and the
               tunnels (including both IPsec tunnels and/or MPLS
               tunnels) interconnecting those edge nodes.

      VPN         Virtual Private Network.

      VRF         VPN Routing and Forwarding instance.

      WAN         Wide Area Network.


3. Framework of SDWAN Edge Discovery


3.1. The Objectives of SDWAN Edge Discovery

   The objectives of SDWAN edge discovery are for an SDWAN edge node to
   discover its authorized peers and their associated properties to
   establish secure tunnels. The attributes to be propagated includes:

      - the SDWAN (client) VPNs information,
      - the attached routes under the SDWAN VPNs,
      - the properties of the underlay networks over which the client
        routes can be carried, and potentially more.

   Some SDWAN peers are connected by both trusted VPNs and untrusted
   public networks. Some SDWAN peers are connected only by untrusted
   public networks. For the traffic over untrusted networks, IPsec
   Security Associations (IPsec SA) must be established and maintained.
   If an edge node has network ports behind a NAT, the NAT properties
   need to be discovered by the authorized SDWAN peers.

   Like any VPN networks, the attached client's routes belonging to
   specific SDWAN VPNs can only be exchanged with the SDWAN peer nodes
   authorized to communicate.

3.2. Comparing with Pure IPsec VPN

   A pure IPsec VPN has IPsec tunnels connecting all edge nodes over
   public networks. Therefore, it requires stringent authentication and
   authorization (i.e., IKE Phase 1) before other properties of IPsec
   SA can be exchanged. The IPsec Security Association (SA) between two
   untrusted nodes typically requires the following configurations and
   message exchanges:


Dunbar, et al.           Expires Dec 26, 2022                  [Page 5]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


       - IPsec IKE to authenticate with each other
       - Establish IPsec SA
            o Local key configuration
            o Remote Peer address (192.10.0.10<->172.0.01)
            o IKEv2 Proposal directly sent to peer
               o Encryption method, Integrity sha512
            o Transform set
       - Attached client prefixes discovery
            o By running routing protocol within each IPsec SA
            o If multiple IPsec SAs between two peer nodes are
               established to achieve load sharing, each IPsec tunnel
               needs to run its own routing protocol to exchange client
               routes attached to the edges.
       - Access List or Traffic Selector)
            o Permit Local-IP1, Remote-IP2

   In a BGP-controlled SDWAN network over hybrid MPLS VPN and public
   internet underlay networks, all edge nodes and RRs are already
   connected by private secure paths. The RRs have the policies to
   manage the authentication of all peer nodes. More importantly, when
   an edge node needs to establish multiple IPsec tunnels to many edge
   nodes, all the management information can be multiplexed into the
   secure management tunnel between RR and the edge node. Therefore,
   the amount of authentication in a BGP-Controlled SDWAN network can
   be significantly reduced.

   Client VPNs are configured via VRFs, just like the configuration of
   the existing MPLS VPN. The IPsec equivalent traffic selectors for
   local and remote routes are achieved by importing/exporting VPN
   Route Targets. The binding of client routes to IPsec SA is dictated
   by policies. As a result, the IPsec configuration for a BGP
   controlled SDWAN (with mixed MPLS VPN) can be simplified:

       - The SDWAN controller has the authority to authenticate edges
          and peers. Remote Peer association is controlled by the SDWAN
          Controller (RR)
       - The IKEv2 proposals, including the IPsec Transform set, can
          be sent directly to peers or incorporated in a BGP UPDATE.
       - BGP UPDATE: Announces the client route reachability for all
          permitted parallel tunnels/paths.
            o There is no need to run multiple routing protocols in
               each IPsec tunnel.



Dunbar, et al.           Expires Dec 26, 2022                  [Page 6]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


       - Importing/exporting Route Targets under each client VPN (VRF)
          achieves the traffic selection (or permission) among clients'
          routes attached to multiple edge nodes.

3.3. Client Route UPDATE and Hybrid Underlay Tunnel UPDATE

   As described in [SDWAN-BGP-USAGE], two separate BGP UPDATE messages
   are used for SDWAN Edge Discovery:

     - UPDATE U1 for advertising the attached client routes,
        This UPDATE is precisely the same as the BGP edge client route
        UPDATE. It uses the Encapsulation Extended Community and the
        Color Extended Community to link with the Underlay Tunnels
        UPDATE Message as specified in section 8 of [RFC9012].

        A new Tunnel Type (SDWAN-Hybrid) is added and used by the
        Encapsulation Extended Community or the Tunnel-Encap Path
        Attribute [RFC9012] to indicate mixed underlay networks.

     - UPDATE U2 advertises the properties of the various tunnels,
        including IPsec, terminated at the edge node.
        This UPDATE is for an edge node to advertise the properties of
        directly attached underlay networks, including the NAT
        information, pre-configured IPsec SA identifiers, and/or the
        underlay network ISP information. This UPDATE can also include
        the detailed IPsec SA attributes, such as keys, nonce,
        encryption algorithms, etc.

   In the following figure: there are four types underlay paths between
   C-PE1 and C-PE2:

      a) MPLS-in-GRE path.

      b) node-based IPsec tunnel [2.2.2.2<->1.1.1.1].

      c) port-based IPsec tunnel [192.0.0.1 <-> 192.10.0.10]; and

      d) port-based IPsec tunnel [172.0.0.1 <-> 160.0.0.1].










Dunbar, et al.           Expires Dec 26, 2022                  [Page 7]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022



                                       +---+
                        +--------------|RR |----------+
                       /  Untrusted    +-+-+           \
                      /                                 \
                     /                                   \
             +---------+  MPLS Path                      +-------+
     11.1.1.x| C-PE1   A1-------------------------------B1 C-PE2 |10.1.1.x
             |         |                                 |       |
     21.1.1.x|         A2(192.10.0.10)------( 192.0.0.1)B2       |20.1.1.x
             |         |                                 |       |
             | Addr    A3(160.0.0.1) --------(170.0.0.1)B3 Addr  |
             | 1.1.1.1 |                                 |2.2.2.2|
             +---------+                                 +-------+

                         Figure 1: Hybrid SDWAN



   C-PE2 uses UPDATE U1 to advertise the attached client routes:

   UDPATE U1:

         Extended community: RT for SDWAN VPN 1
         NLRI: AFI=? & SAFI = 1/1
           Prefix: 10.1.1.x; 20.1.1.x
           NextHop: 2.2.2.2 (C-PE2)
         Encapsulation Extended Community: tunnel-type=SDWAN-Hybrid
         Color Extended Community: RED

   The UPDATE U1 is recursively resolved to the UPDATE U2 which
   specifies the detailed hybrid WAN underlay tunnels terminated at the
   C-PE2:

   UPDATE U2:

     NLRI: SAFI = SDWAN-Hybrid
       (With Color RED encoded in the NLRI Site-Property field)
       Prefix: 2.2.2.2
       Tunnel encapsulation Path Attribute [type=SDWAN-Hybrid]
         IPSec SA for 192.0.0.1
         Tunnel-End-Point Sub-TLV for 192.0.0.1 [RFC9012]
         IPsec-SA-ID sub-TLV [See the Section 6]
       Tunnel encapsulation Path Attribute [type=SDWAN-Hybrid]
         IPSec SA for



Dunbar, et al.           Expires Dec 26, 2022                  [Page 8]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


         Tunnel-End-Point Sub-TLV /* for 170.0.0.1 */
         IPsec-SA-ID sub-TLV
       Tunnel Encap Attr MPLS-in-GRE [type=SDWAN-Hybrid]
         Sub-TLV for MPLS-in-GRE [Section 3.2.6 of RFC9012]

   Note: [RFC9012] Section 11 specifies that each Tunnel Encap
   Attribute can only have one Tunnel-End-Point sub-TLV. Therefore, two
   separate Tunnel Encap Attributes are needed to indicate that the
   client routes can be carried by either one.

3.4. Edge Node Discovery

   The basic scheme of SDWAN edge node discovery using BGP consists of
   the following:

     - Secure connection to a SDWAN controller (i.e., RR in this
        context):
        For an SDWAN edge with both MPLS and IPsec paths, the edge node
        should already have a secure connection to its controller,
        i.e., RR in this context. For an SDWAN edge that is only
        accessible via Internet, the SDWAN edge, upon power-up,
        establishes a secure tunnel (such as TLS or SSL) with the SDWAN
        central controller whose address is preconfigured on the edge
        node. The central controller informs the edge node of its local
        RR. The edge node then establishes a transport layer secure
        session with the RR (such as TLS or SSL).

     - The Edge node will advertise its own properties to its
        designated RR via the secure connection.

     - The RR propagates the received information to the authorized
        peers.

     - The authorized peers can establish the secure data channels
        (IPsec) and exchange more information among each other.
   For an SDWAN deployment with multiple RRs, it is assumed that there
   are secure connections among those RRs. How secure connections are
   established among those RRs is out of the scope of this document.
   The existing BGP UPDATE propagation mechanisms control the edge
   properties propagation among the RRs.

   For some environments where the communication to RR is highly
   secured, [RFC9016] IKE-less can be deployed to simplify IPsec SA
   establishment among edge nodes.


Dunbar, et al.           Expires Dec 26, 2022                  [Page 9]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


4. BGP UPDATE to Support SDWAN Segmentation
4.1. SDWAN Segmentation, SDWAN Virtual Topology and Client VPN

   In SDWAN deployment, "SDWAN Segmentation" is a frequently used term,
   referring to partitioning a network into multiple sub-networks, just
   like MPLS VPNs. "SDWAN Segmentation" is achieved by creating SDWAN
   virtual topologies and SDWAN VPNs. An SDWAN virtual topology
   consists of a set of edge nodes and the tunnels (a.k.a. underlay
   paths), including both IPsec tunnels and/or MPLS VPN tunnels,
   interconnecting those edge nodes.

   An SDWAN VPN is the same as a client VPN, which is configured in the
   same way as the VRFs on PEs of an MPLS VPN. One SDWAN client VPN can
   be mapped to multiple SD-WAN virtual topologies. SDWAN Controller
   governs the policies of mapping a client VPN to SDWAN virtual
   topologies.

   Each SDWAN edge node may need to support multiple VPNs. Just as a
   Route Target is used to distinguish different MPLS VPNs, an SDWAN
   VPN ID is used to differentiate the SDWAN VPNs. For example, in the
   picture below, the "Payment-Flow" on C-PE2 is only mapped to the
   virtual topology of C-PEs to/from Payment Gateway, whereas other
   flows can be mapped to a multipoint-to-multipoint virtual topology.






















Dunbar, et al.           Expires Dec 26, 2022                 [Page 10]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022



                                       +---+
                        +--------------|RR |----------+
                       /  Untrusted    +-+-+           \
                      /                                 \
                     /                                   \
             +---------+  MPLS Path                      +-------+
     11.1.1.x| C-PE1   A1-------------------------------B1 C-PE2 |10.1.1.x
             |         |                                 |       |
     21.1.1.x|         A2(192.10.0.10)------( 192.0.0.1)B2       |20.1.1.x
             |         |                                 |       |
             | Addr    A3(160.0.0.1) --------(170.0.0.1)B3 Addr  |11.2.2.x
             | 1.1.1.1 |                              /  |2.2.2.2|
             +---------+                             /   +-------+
                        \                           /
                         \                         /PaymentFlow
                          \                       /
                           \                +----+----+
                            +---------------| payment |
                                            | Gateway |
                                            +---------+

                 Figure 2: SDWAN Virtual Topology & VPN



4.2. Constrained Propagation of Edge Capability

     BGP has a built-in mechanism to dynamically achieve the
     constrained distribution of edge information. [RFC4684] describes
     the BGP RT constrained distribution. In a nutshell, an SDWAN edge
     sends RT Constraint (RTC) NLRI to the RR for the RR to install an
     outbound route filter, as shown in the figure below:
















Dunbar, et al.           Expires Dec 26, 2022                 [Page 11]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022



         RT Constraint                   RT constraint
         NLRI={SDWAN#1, SDWAN#2}         NLRI={SDWAN#1, SDWAN#3}
                 ----->                 +---+      <-----------
                   +--------------------|RR1|------------------+
                   | Outbound Filter    +---+  Outbound Filter |
                   | Permit SDWAN#1,#2        Permit SDWAN#1,#3|
                   | Deny all                 Deny all         |
                   |   <-------                --------->      |
                   |                                           |
             +-----+---+  MPLS Path                      +-----+-+
     11.1.1.x| C-PE1   A1-------------------------------B1 C-PE2 |10.1.1.x
             |         |                                 |       |
     21.1.1.x|         A2(192.10.0.10)------( 192.0.0.1)B2       |20.1.1.x
             |         |                                 |       |
             | Addr    A3(160.0.0.1) --------(170.0.0.1)B3 Addr  |
             | 1.1.1.1 |                                 |2.2.2.2|
             +---------+                                 +-------+
     SDWAN VPN #1                                          SDWAN VPN #1
     SDWAN VPN #2                                          SDWAN VPN #3
           Figure 3: Constraint propagation of Edge Property

     However, a SDWAN overlay network can span across untrusted
     networks, RR can't trust the RT Constraint (RTC) NLRI BGP UPDATE
     from any nodes. RR can only process the RTC NLRI from authorized
     peers for a SDWAN VPN.

     It is out of the scope of this document on how RR is configured
     with the policies to filter out unauthorized nodes for specific
     SDWAN VPNs.

     When the RR receives BGP UPDATE from an edge node, it propagates
     the received UPDATE message to the nodes that are in the Outbound
     Route filter for the specific SDWAN VPN.

5. Client Route UPDATE

   The SDWAN network's Client Route UPDATE message is the same as the
   MPLS VPN client route UDPATE message. The SDWAN Client Route UPDATE
   message uses the Encapsulation Extended Community and the Color
   Extended Community to link with the Underlay Tunnels UPDATE Message.






Dunbar, et al.           Expires Dec 26, 2022                 [Page 12]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


5.1. SDWAN VPN ID in Client Route Update

   An SDWAN VPN is same as a client VPN in a BGP controlled SDWAN
   network. The Route Target Extended Community should be included in a
   Client Route UPDATE message to differentiate the client routes from
   routes belonging to other VPNs.

5.2. SDWAN VPN ID in Data Plane

   For an SDWAN edge node which can be reached by both MPLS and IPsec
   paths, the client packets reached by MPLS network will be encoded
   with the MPLS Labels based on the scheme specified by [RFC8277].

   For GRE Encapsulation within an IPsec tunnel, the GRE key field can
   be used to carry the SDWAN VPN ID. For network virtual overlay
   (VxLAN, GENEVE, etc.) encapsulation within the IPsec tunnel, the
   Virtual Network Identifier (VNI) field is used to carry the SDWAN
   VPN ID.

6. Hybrid Underlay Tunnel UPDATE

   The hybrid underlay tunnel UPDATE is to advertise the detailed
   properties of hybrid types of tunnels terminated at a SDWAN edge
   node.

   A client route UDPATE is recursively tied to an underlay tunnel
   UDPATE by the Color Extended Community included in client route
   UPDATE.

 6.1. NLRI for Hybrid Underlay Tunnel Update

   A new NLRI is introduced within the MP_REACH_NLRI Path Attribute of
   RFC4760, for advertising the detailed properties of hybrid types of
   tunnels terminated at the edge node, with SAFI=SDWAN (code = 74):















Dunbar, et al.           Expires Dec 26, 2022                 [Page 13]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


     +------------------+
     |   NLRI Length    | 1 octet
     +------------------+
     |   Site-Type      | 2 Octet
     +------------------+
     |   Port-Local-ID  | 4 octets
     +------------------+
     |  SDWAN-Color     | 4 octets
     +------------------+
     |  SDWAN-Node-ID   | 4 or 16 octets
     +------------------+


   where:

     - NLRI Length: 1 octet of length expressed in bits as defined in
       [RFC4760].
     - Site Type: 2 octet value. The SDWAN Site Type defines the
       different types of Site IDs to be used in the deployment. This
       document defines the following types:
          Site-Type = 1: For a simple deployment, such as all edge
          nodes under one SDWAN management system, the node ID is
          enough for the SDWAN management to map the site to its
          precise geolocation.
          Site-Type = 2: For large SDWAN heterogeneous deployment where
          a Geo-Loc Sub-TLV [LISP-GEOLoc]is needed to fully describe
          the accurate location of the node.
     -            Port local ID: SDWAN edge node Port identifier, which is locally
       significant. If the SDWAN NLRI applies to multiple ports, this
       field is NULL.
     - SDWAN-Color: to correlate with the Color-Extended-community
       included in the client routes UPDATE.
     - SDWAN Edge Node ID: The node's IPv4 or IPv6 address.








Dunbar, et al.           Expires Dec 26, 2022                 [Page 14]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


6.2. SDWAN-Hybrid Tunnel Encoding

   A new BGP Tunnel-Type=SDWAN-Hybrid (code point TBD1) is specified
   for the Tunnel Encapsulation Attribute to indicate hybrid underlay
   networks.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Tunnel-Type(=SDWAN-Hybrid )   | Length (2 Octets)             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                           Sub-TLVs                            |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
           SDWAN Hybrid Underlay network Sub-TLV Value Field


6.3. IPsec-SA-ID Sub-TLV

   IPsec-SA-ID Sub-TLV for the Hybrid Underlay Tunnel UPDATE indicates
   one or more preestablished IPsec SAs by using their identifiers,
   instead of listing all the detailed attributes of the IPsec SAs.

   Using an IPsec-SA-ID Sub-TLV not only greatly reduces the size of
   BGP UPDATE messages, but also allows the pairwise IPsec rekeying
   process to be performed independently.

   The following is the structure of the IPsec-SA-ID sub-TLV:

    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Type= IPsec-SA-ID subTLV (TBD2)|  Length (2 Octets)            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      IPsec SA Identifier #1                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      IPsec SA Identifier #2                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If the client traffic needs to be encapsulated in a specific way
   within the IPsec ESP Tunnel, such as GRE or VxLAN, etc., the
   corresponding Tunnel-Encap Sub-TLV needs to be prepended right
   before the IPsec-SA-ID Sub-TLV.






Dunbar, et al.           Expires Dec 26, 2022                 [Page 15]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


6.3.1. Encoding example #1 of using IPsec-SA-ID Sub-TLV

   This section provides an encoding example for the following
   scenario:

     - There are four IPsec SAs terminated at the same WAN Port
        address (or the same node address)
     - Two of the IPsec SAs use GRE (value =2) as Inner Encapsulation
        within the IPsec Tunnel
     - two of the IPsec SA uses VxLAN (value = 8) as the Inner
        Encapsulation within its IPsec Tunnel.


   Here is the encoding for the scenario:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Tunnel-Type =SDWAN-Hybrid     |       Length =                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Tunnel-end-Point Sub-TLV                           |
   ~                                                               ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                      GRE Sub-TLV                              ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | subTLV-Type = IPsec-SA-ID     |       Length =                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     IPsec SA Identifier = 1                   |
   +---------------------------------------------------------------+
   |                     IPsec SA Identifier = 2                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                      VxLAN Sub-TLV                            ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |subTLV-Type = IPsec-SA-ID      |        Length=                |
   +-------------------------------+-------------------------------+
   |                     IPsec SA Identifier = 3                   |
   +-------------------------------+-------------------------------+
   |                     IPsec SA Identifier = 4                   |
   +---------------------------------------------------------------+

  The Length of the Tunnel-Type = SDDWAN-Hybrid is the sum of the
  following:
  -  Tunnel-end-point sub-TLV total length
  -  The GRE Sub-TLV total length,



Dunbar, et al.           Expires Dec 26, 2022                 [Page 16]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


  -  The IPsec-SA-ID Sub-TLV length,
  -  The VxLAN sub-TLV total length, and
  -  The IPsec-SA-ID Sub-TLV length.

6.3.2. Encoding Example #2 of using IPsec-SA-ID Sub-TLV

   For IPsec SAs terminated at different endpoints, multiple Tunnel Encap
   Attributes must be included. This section provides an encoding example for
   the following scenario:

     - there is one IPsec SA terminated at the WAN Port address
        192.0.0.1; and another IPsec SA terminated at WAN Port
        170.0.0.1;
     - Both IPsec SAs use GRE (value =2) as Inner Encapsulation within
        the IPsec Tunnel


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Tunnel-Type =SDWAN-Hybrid     |       Length =                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Tunnel-end-Point Sub-TLV                           |
   ~            for  192.0.0.1                                     ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                   GRE Sub-TLV                                 ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~           IPsec-SA-ID sub-TLV #1                              ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Tunnel-Type =SDWAN-Hybrid     |       Length =                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Tunnel-end-Point Sub-TLV                           |
   ~            for  170.0.0.1                                    ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                   GRE sub-TLV                                 ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~             IPsec-SA-ID sub-TLV #2                            ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+









Dunbar, et al.           Expires Dec 26, 2022                 [Page 17]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


 6.4. Extended Port Tunnel Encapsulation Attribute Sub-TLV

   When a SDWAN edge node is connected to an underlay network via a
   port behind NAT devices, traditional IPsec uses IKE for NAT
   negotiation. The location of a NAT device can be such that:
     - Only the initiator is behind a NAT device. Multiple initiators
       can be behind separate NAT devices. Initiators can also connect
       to the responder through multiple NAT devices.
     - Only the responder is behind a NAT device.
     - Both the initiator and the responder are behind a NAT device.


   The initiator's address and/or responder's address can be
   dynamically assigned by an ISP or when their connection crosses a
   dynamic NAT device that allocates addresses from a dynamic address
   pool.

   Because one SDWAN edge can connect to multiple peers via one
   underlay network, the pair-wise NAT exchange as IPsec's IKE is not
   efficient. In BGP Controlled SDWAN, NAT information of a WAN port is
   advertised to its RR in the BGP UPDATE message. It is encoded as an
   Extended sub-TLV that describes the NAT property if the port is
   behind a NAT device.

   An SDWAN edge node can ask a STUN Server (Session Traversal of UDP
   Through Network Address Translation [RFC3489]) to get the NAT
   properties, the public IP address and the Public Port number to pass
   to peers.


        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |Port Ext Type  |  EncapExt subTLV Length       |I|O|R|R|R|R|R|R|
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | NAT Type      |  Encap-Type   |Trans networkID|     RD ID     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                  Local  IP Address                            |
                  32-bits for IPv4, 128-bits for Ipv6
                          ~~~~~~~~~~~~
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                  Local  Port                                  |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Dunbar, et al.           Expires Dec 26, 2022                 [Page 18]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


      |                Public IP                                      |
                  32-bits for IPv4, 128-bits for Ipv6
                          ~~~~~~~~~~~~
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                Public Port                                    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                ISP-Sub-TLV                                    |
      ~                                                               ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   Where:

     o Port Ext Type (TBD3): indicating it is the Port Ext SubTLV.
     o PortExt subTLV Length: the length of the subTLV.
     o Flags:
          - I bit (CPE port address or Inner address scheme)
             If set to 0, indicate the inner (private) address is IPv4.
             If set to 1, it indicates the inner address is IPv6.

          - O bit (Outer address scheme):
             If set to 0, indicate the public (outer) address is IPv4.
             If set to 1, it indicates the public (outer) address is
             IPv6.

          - R bits: reserved for future use. Must be set to 0 now.


     o NAT Type.without NAT; 1:1 static NAT; Full Cone; Restricted
        Cone; Port Restricted Cone; Symmetric; or Unknown (i.e. no
        response from the STUN server).
     o Encap Type.the supported encapsulation types for the port
        facing public network, such as IPsec+GRE, IPsec+VxLAN, IPsec
        without GRE, GRE (when packets don't need encryption)
     o Transport Network ID.Central Controller assign a global unique
        ID to each transport network.
     o RD ID.Routing Domain ID.need to be global unique.
     o Local IP.The local (or private) IP address of the port.
     o Local Port.used by Remote SDWAN edge node for establishing
        IPsec to this specific port.




Dunbar, et al.           Expires Dec 26, 2022                 [Page 19]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


     o Public IP.The IP address after the NAT. If NAT is not used,
        this field is set to NULL.
     o Public Port.The Port after the NAT. If NAT is not used, this
        field is set to NULL.

 6.5. Underlay Network Properties Sub-TLV

   The purpose of the Underlay Network Sub-TLV is to carry the WAN port
   properties with SDWAN SAFI NLRI. It would be treated as optional
   Sub-TLV. The BGP originator decides whether to include this Sub-TLV
   along with the SDWAN NLRI. If this Sub-TLV is present, it would be
   processed by the BGP receiver and to determine what local policies
   to apply for the remote end point of the underlay tunnel.

   The format of this Sub-TLV is as follows:

        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | Type=TBD4     |      Length   |      Flag     |    Reserved   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |Connection Type|   Port Type   |        Port Speed             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where:

      Type: TBD4.

      Length: always 6 bytes.

      Flag: a 1 octet value.

      Reserved: 1 octet of reserved bits. It SHOULD be set to zero on
      transmission and MUST be ignored on receipt.

      Connection Type: There are two different types of WAN
      Connectivity. They are listed below as:

      Wired - 1
      WIFI - 2
      LTE - 3
      5G  - 4




Dunbar, et al.           Expires Dec 26, 2022                 [Page 20]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


      Port Type: There are different types of ports. They are listed
      Below as:

      Ethernet  - 1
      Fiber Cable - 2
      Coax Cable - 3
      Cellular - 4

      Port Speed: The port seed is defined as 2 octet value. The values
      are defined as Gigabit speed.





7. IPsec SA Property Sub-TLVs

   This section describes the detailed IPsec SA properties sub-TLVs.

7.1. IPsec SA Nonce Sub-TLV

   The Nonce Sub-TLV is based on the Base DIM sub-TLV as described the
   Section 6.1 of [SECURE-EVPN]. The IPsec SA ID is included in the
   sub-TLV, which is to be referenced by the client route NLRI Tunnel
   Encapsulation Path Attribute for the IPsec SA.  The following fields
   are removed because:

        - the Originator ID is carried by the NLRI,
        - the Tenant ID is represented by the SDWAN VPN ID Extended
           Community, and
        - the Subnet ID are carried by the BGP route UPDATE.


    The format of this Sub-TLV is as follows:












Dunbar, et al.           Expires Dec 26, 2022                 [Page 21]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |   ID Length   |       Nonce Length            |I|   Flags     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                             Rekey                             |
       |                            Counter                            |
       +---------------------------------------------------------------+
       |      IPsec SA ID              |        Reserved               |
       +---------------------------------------------------------------+
       |                                                               |
       ~                          Nonce Data                           ~
       |                                                               |
       +---------------------------------------------------------------+


   IPsec SA ID - The 2 bytes IPSec SA ID could 0 or non-zero values. It
   is cross referenced by client route's IPSec Tunnel Encapsulation
   IPSec-SA-ID SubTLV in Section 6. When there are multiple IPsec SAs
   terminated at one address, such as WAN port address or the node
   address, they are differentiated by the different IPsec SA IDs.



7.2. IPsec Public Key Sub-TLV

   The IPsec Public Key Sub-TLV is derived from the Key Exchange Sub-
   TLV described in [SECURE-EVPN] with an addition of Duration filed to
   define the IPSec SA life span. The edge nodes would pick the
   shortest duration value between the SDWAN SAFI pairs.

   The format of this Sub-TLV is as follows:

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |   Diffie-Hellman Group Num    |          Reserved             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       ~                       Key Exchange Data                       ~
       |                                                               |
       +---------------------------------------------------------------+
       |                            Duration                           |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




Dunbar, et al.           Expires Dec 26, 2022                 [Page 22]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


7.3. IPsec SA Proposal Sub-TLV

   The IPsec SA Proposal Sub-TLV is to indicate the number of Transform
   Sub-TLVs. This Sub-TLV aligns with the sub-TLV structure from
   [SECURE-VPN]

   The Transform Sub-sub-TLV will following the section 3.3.2 of
   RFC7296.



7.4. Simplified IPsec Security Association sub-TLV

     For a simple SDWAN network with edge nodes supporting only a few
     pre-defined encryption algorithms, a simple IPsec sub-TLV can be
     used to encode the pre-defined algorithms, as below:

        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |IPsec-simType  |IPsecSA Length                 | Flag          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | Transform     | Mode          | AH algorithms |ESP algorithms |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |         ReKey Counter (SPI)                                   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | key1 length   |         Public Key                            ~
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | key2 length   |         Nonce                                 ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |        Duration                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



   Where:

     o IPsec-SimType: The type value has to be between 128~255 because
        IPsec-SA subTLV needs 2 bytes for length to carry the needed
        information.
     o IPsec-SA subTLV Length (2 Byte): 25 (or more)
     o Flags: 1 octet of flags. None are defined at this stage. Flags
        SHOULD be set to zero on transmission and MUST be ignored on
        receipt.
     o Transform (1 Byte):  the value can be AH, ESP, or AH+ESP.



Dunbar, et al.           Expires Dec 26, 2022                 [Page 23]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


     o IPsec Mode (1 byte): the value can be Tunnel Mode or Transport
        mode
     o AH algorithms (1 byte): AH authentication algorithms supported,
        which can be md5 | sha1 | sha2-256 | sha2-384 | sha2-512 | sm3.
        Each SDWAN edge node can have multiple authentication.
        algorithms; send to its peers to negotiate the strongest one.
     o ESP (1 byte): ESP authentication algorithms supported, which
        can be md5 | sha1 | sha2-256 | sha2-384 | sha2-512 | sm3. Each
        SDWAN edge node can have multiple authentication algorithms;
        send to its peers to negotiate the strongest one. Default
        algorithm is AES-256.
          o When node supports multiple authentication algorithms, the
             initial UPDATE needs to include the "Transform Sub-TLV"
             described by [SECURE-EVPN] to describe all of the
             algorithms supported by the node.

     o Rekey Counter (Security Parameter Index)): 4 bytes
     o Public Key: IPsec public key
     o Nonce.IPsec Nonce
     o Duration: SA life span.



7.5. IPsec SA Encoding Examples

   For the Figure 1 in Section 3, C-PE2 needs to advertise its IPsec SA
   associated attributes, such as the public keys, the nonce, the
   supported encryption algorithms for the IPsec tunnels terminated at
   192.0.0.1, 170.1.1.1 and 2.2.2.2 respectively.

   Using the IPsec Tunnel [ISP4: 160.0.0.1 <-> ISP2:170.0.0.1] as an
   example: C-PE1 needs to advertise the following attributes for
   establishing the IPsec SA:
     SDWAN Node ID
     SDWAN Color
     Tunnel Encap Attr (Type=SDWAN-Hybrid)
          Extended Port Sub-TLV for information about the Port
          (including ISP Sub-TLV for information about the ISP2)
          IPsec SA Nonce Sub-TLV,
          IPsec SA Public Key Sub-TLV,
          IPsec SA Sub-TLV for the supported transforms



Dunbar, et al.           Expires Dec 26, 2022                 [Page 24]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


               {Transforms Sub-TLV - Trans 2,
               Transforms Sub-TLV - Trans 3}

   C-PE2 needs to advertise the following attributes for establishing
   IPsec SA:
     SDWAN Node ID
     SDWAN Color
     Tunnel Encap Attr (Type=SDWAN-Hybrid)
          Extended Port Sub-TLV (including ISP Sub-TLV for information
          about the ISP2)
          IPsec SA Nonce Sub-TLV,
          IPsec SA Public Key Sub-TLV,
          IPsec SA Sub-TLV for the supported transforms
               {Transforms Sub-TLV - Trans 2,
               Transforms Sub-TLV - Trans 4}

   As both end points support Transform #2, the Transform #2 will be
   used for the IPsec Tunnel [ISP4: 160.0.0.1 <-> ISP2:170.0.0.1].


8. Error & Mismatch Handling


   Each C-PE device advertises a SDWAN SAFI Underlay NLRI to the other
   C-PE devices via a BGP Route Reflector to establish pairwise SAs
   between itself and every other remote C-PEs. During the SAFI NLRI
   advertisement, the BGP originator would include either simple IPSec
   Security Association properties defined in IPSec SA Sub-TLV based on
   IPSec-SA-Type = 1 or full-set of IPSec Sub-TLVs including Nonce,
   Public Key, Proposal and number of Transform Sub-TLVs based on
   IPSec-SA-Type = 2.

   The C-PE devices compare the IPSec SA attributes between the local
   and remote WAN ports. If there is a match on the SA Attributes
   between the two ports, the IPSec Tunnel is established.

   The C-PE devices would not try to negotiate the base IPSec-SA
   parameters between the local and the remote ports in the case of
   simple IPSec SA exchange or the Transform sets between local and
   remote ports if there is a mismatch on the Transform sets in the
   case of full-set of IPSec SA Sub-TLVs.





Dunbar, et al.           Expires Dec 26, 2022                 [Page 25]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


   As an example, using the Figure 1 in Section 3, to establish IPsec
   Tunnel between C-PE1 and C-PE2 WAN Ports A2 and B2 [A2: 192.10.0.10
   <-> B2:192.0.0.1]:


   C-PE1 needs to advertise the following attributes for establishing
   the IPsec SA:
     NH: 192.10.0.10
     SDWAN Node ID
     SDWAN-Site-ID
     Tunnel Encap Attr (Type=SDWAN)
          ISP Sub-TLV for information about the ISP3
          IPsec SA Nonce Sub-TLV,
          IPsec SA Public Key Sub-TLV,
          Proposal Sub-TLV with Num Transforms = 1
               {Transforms Sub-TLV - Trans 1}

   C-PE2 needs to advertise the following attributes for establishing
   IPsec SA:
     NH: 192.0.0.1
     SDWAN Node ID
     SDWAN-Site-ID
     Tunnel Encap Attr (Type=SDWAN)
          ISP Sub-TLV for information about the ISP1
          IPsec SA Nonce Sub-TLV,
          IPsec SA Public Key Sub-TLV,
          Proposal Sub-TLV with Num Transforms = 1
               {Transforms Sub-TLV - Trans 2}

   As there is no matching transform between the WAN ports A2 and B2 in
   C-PE1 and C-PE2 respectively, there will be no IPsec Tunnel be
   established.


9. Manageability Considerations

      TBD - this needs to be filled out before publishing







Dunbar, et al.           Expires Dec 26, 2022                 [Page 26]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


10. Security Considerations

     The document describes the encoding for SDWAN edge nodes to
     advertise its properties to their peers to its RR, which
     propagates to the intended peers via untrusted networks.

     The secure propagation is achieved by secure channels, such as
     TLS, SSL, or IPsec, between the SDWAN edge nodes and the local
     controller RR.

    [More details need to be filled in here]


11. IANA Considerations
11.1. Hybrid (SDWAN) Overlay SAFI

   IANA has assigned SAFI = 74 as the Hybrid (SDWAN)SAFI.

11.2. Tunnel Encapsulation Attribute Type

   IANA is requested to assign a type from the BGP Tunnel Encapsulation
   Attribute Tunnel Types as follows:

   Value   Description    Reference
   -----   ------------   ---------
    TBD1   SDWAN-Hybrid   [this document]

11.3 Tunnel Encapsulation Attribute Sub-TLV Types

   IANA is requested to assign three Types, as follows, in the BGP Tunnel
   Encapsulation Attribute Sub-TLVs regustry:


   Value    Description               Reference
   -----   -----------------------   ---------------
    TBD2   IPSEC-SA-ID               [this document]
    TBD3   Port Extension            [this document]
    TBD4   Underlay ISP Properties   [this document]








Dunbar, et al.           Expires Dec 26, 2022                 [Page 27]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


12. References


 12.1. Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
             Border Gateway Protocol 4 (BGP-4)", RFC 4271, DOI
             10.17487/RFC4271, January 2006, <https://www.rfc-
             editor.org/info/rfc4271>.

   [RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
             "Multiprotocol Extensions for BGP-4", RFC 4760, DOI
             10.17487/RFC4760, January 2007, <https://www.rfc-
             editor.org/info/rfc4760>.

   [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
             2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
             May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC9012] Patel, K., Van de Velde, G., Sangli, S., and J. Scudder,
             "The BGP Tunnel Encapsulation Attribute", RFC 9012, DOI
             10.17487/RFC9012, April 2021, <https://www.rfc-
             editor.org/info/rfc9012>.


 12.2. Informative References

   [RFC8192] S. Hares, et al, "Interface to Network Security Functions
             (I2NSF) Problem Statement and Use Cases", July 2017

   [RFC5521] P. Mohapatra, E. Rosen, "The BGP Encapsulation Subsequent
             Address Family Identifier (SAFI) and the BGP Tunnel
             Encapsulation Attribute", April 2009.








Dunbar, et al.           Expires Dec 26, 2022                 [Page 28]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


   [RFC9061] Marin-Lopez, R., Lopez-Millan, G., and F. Pereniguez-
             Garcia, "A YANG Data Model for IPsec Flow Protection Based
             on Software-Defined Networking (SDN)", RFC 9061, DOI
             10.17487/RFC9061, July 2021, <https://www.rfc-
             editor.org/info/rfc9061>.

   [CONTROLLER-IKE] D. Carrel, et al, "IPsec Key Exchange using a
             Controller", draft-carrel-ipsecme-controller-ike-01, work-
             in-progress.

   [LISP-GEOLOC] D. Farinacci, "LISP Geo-Coordinate Use-Case", draft-
             farinacci-lisp-geo-09, April 2020.

   [SDN-IPSEC] R. Lopez, G. Millan, "SDN-based IPsec Flow Protection",
             draft-ietf-i2nsf-sdn-ipsec-flow-protection-07, Aug 2019.

   [SECURE-EVPN] A. Sajassi, et al, "Secure EVPN", draft-sajassi-bess-
             secure-evpn-02, July 2019.

   [VPN-over-Internet] E. Rosen, "Provide Secure Layer L3VPNs over
             Public Infrastructure", draft-rosen-bess-secure-l3vpn-00,
             work-in-progress, July 2018

   [DMVPN] Dynamic Multi-point VPN:
             https://www.cisco.com/c/en/us/products/security/dynamic-
             multipoint-vpn-dmvpn/index.html

   [DSVPN] Dynamic Smart VPN:
             http://forum.huawei.com/enterprise/en/thread-390771-1-
             1.html



   [ITU-T-X1036] ITU-T Recommendation X.1036, "Framework for creation,
             storage, distribution and enforcement of policies for
             network security", Nov 2007.

   [Net2Cloud-Problem] L. Dunbar and A. Malis, "Dynamic Networks to
             Hybrid Cloud DCs Problem Statement", draft-ietf-rtgwg-
             net2cloud-problem-statement-12, March 7, 2022.



Dunbar, et al.           Expires Dec 26, 2022                 [Page 29]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


   [Net2Cloud-gap] L. Dunbar, A. Malis, and C. Jacquenet, "Networks
             Connecting to Hybrid Cloud DCs: Gap Analysis", draft-ietf-
             rtgwg-net2cloud-gap-analysis-07, July, 2020.

   [RFC9012] K. Patel, et al "The BGP Tunnel Encapsulation Attribute",
             RFC9012, April 2021.



13. Acknowledgments

   Acknowledgements to Wang Haibo, Hao Weiguo, and ShengCheng for
   implementation contribution; Many thanks to Yoav Nir, Graham
   Bartlett, Jim Guichard, John Scudder, and Donald Eastlake for their
   review and suggestions.

   This document was prepared using 2-Word-v2.0.template.dot.




























Dunbar, et al.           Expires Dec 26, 2022                 [Page 30]


Internet-Draft       BGP for SDWAN Edge Discovery            April 2022


Authors' Addresses


   Linda Dunbar
   Futurewei
   Email: ldunbar@futurewei.com

   Sue Hares
   Hickory Hill Consulting
   Email: shares@ndzh.com

   Robert Raszuk
   NTT Network Innovations
   Email: robert@raszuk.net

   Kausik Majumdar
   CommScope
   Email: Kausik.Majumdar@commscope.com

   Gyan Mishra
   Verizon Inc.
   Email: gyan.s.mishra@verizon.com

Contributors' Addresses
   Donald Eastlake
   Futurewei
   Email: d3e3e3@gmail.com


















Dunbar, et al.           Expires Dec 26, 2022                 [Page 31]