IPCDN Working Group D. Raftus
Internet Draft Terayon Canada Ltd.
Document: draft-ietf-ipcdn-docs-rfmibv2-07 September 2003
Expires: March 2004
Obsoletes: RFC2670
Radio Frequency (RF) Interface Management Information Base
for DOCSIS 2.0 compliant RF interfaces
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use
Internet-Drafts as reference material or to cite them other than
as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Abstract
This memo is a draft revision of the standards track RFC-2670.
Please see "Section 9 Changes from RFC2670" for a description of
modifications. This document or its successor will obsolete RFC-2670
when accepted.
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines a basic set of managed objects for SNMP-
based management of DOCSIS compliant Radio Frequency (RF)
interfaces.
This memo is a product of the IPCDN working group within the
Internet Engineering Task Force. Comments are solicited and should
be addressed to the working group's mailing list at ipcdn@ietf.org
and/or the authors.
Raftus [Page 1]
Internet Draft DOCSIS RF Interface MIB September 2003
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in BCP 14,
RFC 2119 [RFC2119].
Table of Contents
1 The SNMP Management Framework ................................. 3
2 Glossary ...................................................... 3
2.1 CATV ........................................................ 3
2.2 Channel ..................................................... 3
2.3 CM .......................................................... 4
2.4 CMTS ........................................................ 4
2.5 Codeword .................................................... 4
2.6 Data Packet ................................................. 4
2.7 dBmV ........................................................ 4
2.8 DOCSIS ...................................................... 4
2.9 Downstream .................................................. 4
2.10 Head-end ................................................... 5
2.11 MAC Packet ................................................. 5
2.12 MCNS ....................................................... 5
2.13 Mini-slot .................................................. 5
2.14 QPSK ....................................................... 5
2.15 QAM ........................................................ 5
2.16 RF ......................................................... 5
2.17 Symbol-times ............................................... 5
2.18 Upstream ................................................... 5
3 Overview ...................................................... 5
3.1 Structure of the MIB ........................................ 6
3.1.1 docsIfBaseObjects ......................................... 6
3.1.2 docsIfCmObjects ........................................... 6
3.1.3 docsIfCmtsObjects ......................................... 7
3.2 Relationship to the Interfaces MIB .......................... 7
3.2.1 Layering Model ............................................ 7
3.2.2 Virtual Circuits .......................................... 9
3.2.3 ifTestTable ............................................... 9
3.2.4 ifRcvAddressTable ......................................... 9
3.2.5 ifEntry ................................................... 9
3.2.5.1 ifEntry for Downstream interfaces ....................... 9
3.2.5.1.1 ifEntry for Downstream interfaces in Cable Modem
Termination Systems ........................................ 9
3.2.5.1.2 ifEntry for Downstream interfaces in Cable Modems .... 11
3.2.5.2 ifEntry for Upstream interfaces ........................ 13
3.2.5.2.1 ifEntry for Upstream interfaces in Cable Modem
Termination Systems ....................................... 13
3.2.5.2.2 ifEntry for Upstream interfaces in Cable Modems ...... 15
3.2.5.3 ifEntry for Upstream channels .......................... 16
3.2.5.3.1 ifEntry for Upstream Channels in Cable Modem
Raftus Expires March 2004 [Page 2]
Internet Draft DOCSIS RF Interface MIB September 2003
Termination Systems ....................................... 16
3.2.5.4 ifEntry for the MAC Layer .............................. 18
4 Definitions .................................................. 20
5 Acknowledgments ............................................. 118
6 Revision History ............................................ 118
7 Normative References ........................................ 118
8 Informative References ...................................... 121
9 Security Considerations ..................................... 121
10 Changes from RFC2670 ....................................... 121
11 Conflict Resolution with docsIfExt MIB ..................... 123
12 Intellectual Property .......................................123
13 Author's Address ........................................... 124
14 Full Copyright Statement ................................... 124
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7
of RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. MIB objects are
generally accessed through the Simple Network Management Protocol
(SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in
STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58,
RFC 2580 [RFC2580].
2. Glossary
The terms in this document are derived either from normal cable
system usage, or from the documents associated with the Data Over
Cable Service Interface Specification process.
2.1. CATV
Originally "Community Antenna Television", now used to refer to any
cable or hybrid fiber and cable system used to deliver video signals
to a community.
2.2. Channel
A specific frequency allocation with an RF medium, specified by
channel width in Hertz (cycles per second) and by center frequency.
Within the US Cable Systems, upstream channels are generally
allocated from the 5-42MHz range while down stream channels are
Raftus Expires March 2004 [Page 3]
Internet Draft DOCSIS RF Interface MIB September 2003
generally allocated from the 50-750MHz range depending on the
capabilities of the given system. The typical broadcast channel
width in the US is 6MHz. Upstream channel widths for DOCSIS vary.
For European cable systems, upstream channels vary by country. The
upper edge of upstream channel allocations vary between 25 MHz to 65
MHz, and the lower edge of downstream channel allocations vary
between 47 MHz and 87.5 MHz. The typical broadcast channel width in
Europe is 8MHz. The actual parameters are of concern to systems
deploying EuroDOCSIS technology.
2.3. CM Cable Modem.
A CM acts as a "slave" station in a DOCSIS compliant cable data
system.
2.4. CMTS Cable Modem Termination System.
A generic term covering a cable bridge or cable router in a
head-end. A CMTS acts as the master station in a DOCSIS compliant
cable data system. It is the only station that transmits
downstream, and it controls the scheduling of upstream
transmissions by its associated CMs.
2.5. Codeword
A characteristic of the Forward Error Correction scheme used
above the RF media layer.
See "Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730"
2.6. Data Packet
The payload portion of the MAC Packet.
2.7. dBmV
A measure of RF signal voltage amplitude, whose power level is
determined by the characteristic impedance. A zero dB signal power
is equivalent to 48.75 dBmV signal amplitude in a 75 Ohm system.
2.8. DOCSIS
"Data Over Cable Service Interface Specification". A term
referring to the ITU-T J.112 Annex B standard for cable modem
systems [7].
2.9. Downstream
The direction from the head-end towards the subscriber.
Raftus Expires March 2004 [Page 4]
Internet Draft DOCSIS RF Interface MIB September 2003
2.10. Head-end
The origination point in most cable systems of the subscriber video
signals.
2.11. MAC Packet
A DOCSIS PDU.
2.12. MCNS
"Multimedia Cable Network System". Generally replaced in usage by
DOCSIS.
2.13. Mini-slot
In general, an interval of time which is allocated by the
CMTS to a given CM for that CM to transmit in an upstream direction.
See "Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730",
2.14. QPSK Quadrature Phase Shift Keying.
A particular modulation scheme on an RF medium. See [6].
2.15. QAM Quadrature Amplitude Modulation.
A particular modulation scheme on RF medium. Usually expressed
with a number indicating the size of the modulation constellation
(e.g. 16 QAM). See [6], or any other book on digital communications
over RF for a complete explanation of this.
2.16. RF
Radio Frequency.
2.17. Symbol-times
A characteristic of the RF modulation scheme.
See "Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730"
2.18. Upstream
The direction from the subscriber towards the head-end.
3. Overview
This MIB provides a set of objects required for the management of
MCNS/DOCSIS compliant Cable Modem (CM) and Cable Modem Termination
System (CMTS) RF interfaces. The specification is derived in part
Raftus Expires March 2004 [Page 5]
Internet Draft DOCSIS RF Interface MIB September 2003
from the parameters and protocols described in "Data-Over-Cable
Service Interface Specifications: Radio Frequency Interface
Specification SP-RFIv2.0-I04-030730".
3.1. Structure of the MIB
This MIB is structured as three groups:
o Management information pertinent to both Cable Modems (CM) and
Cable Modem Termination Systems (CMTS) (docsIfBaseObjects).
o Management information pertinent to Cable Modems only
(docsIfCmObjects).
o Management information pertinent to Cable Modem Termination
Systems only (docsIfCmtsObjects).
Tables within each of these groups group objects functionally - e.g.
Quality of Service, Channel characteristics, MAC layer management,
etc. Rows created automatically (e.g. by the device according to
the hardware configuration) may and generally will have a mixture of
configuration and status objects within them. Rows that are meant
to be created by the management station are generally restricted to
configuration (read-create) objects.
3.1.1. docsIfBaseObjects
docsIfDownstreamChannelTable - This table describes the active
downstream channels for a CMTS and the received downstream channel
for a CM.
docsIfUpstreamChannelTable - This table describes the active
upstream channels for a CMTS and the current upstream transmission
channel for a CM.
docsIfQosProfileTable - This table describes the valid Quality of
Service profiles for the cable data system.
docsIfSignalQualityTable - This table is used to monitor RF signal
quality characteristics of received signals.
docsIfDocsisBaseCapability - This object is used to indicate the
highest level of DOCSIS version a cable device can support.
3.1.2. docsIfCmObjects
docsIfCmMacTable - This table is used to monitor the DOCSIS MAC
interface and can be considered an extension to the ifEntry.
docsIfCmStatusTable - This table maintains a number of status
objects and counters for cable modems. There is a comparable table
at the CMTS, docsIfCmtsCmStatusTable, which maintains similar
Raftus Expires March 2004 [Page 6]
Internet Draft DOCSIS RF Interface MIB September 2003
counters from the CMTS point of view.
docsIfCmServiceTable - This table describes the upstream service
queues available at this CM. There is a comparable table at the
CMTS, docsIfCmtsServiceEntry, which describes the service queues
from the point of view of the CMTS.
3.1.3. docsIfCmtsObjects
docsIfCmtsMacTable - Describes the attributes of each CMTS MAC
interface.
docsIfCmtsStatusTable - This table provides a set of aggregated
counters which roll-up values and events that occur on the
underlying sub-interfaces.
docsIfCmtsCmStatusTable - This table is used to hold information
about known (i.e. ranging, registered, and/or previously online)
cable modems on the system serviced by this CMTS.
docsIfCmtsServiceTable - This table provides access to the
information related to upstream service queues.
docsIfCmtsModulationTable - This table allows control over the
modulation profiles for RF channels associated with this CMTS.
docsIfCmtsMacToCmTable - This table allows fast access into the
docsIfCmtsCmTable via a MAC address (of the CM) interface.
docsIfCmtsChannelUtilizationTable - This table provides statistical
load usage data for attached upstream and downstream physical
channels.
docsIfCmtsDownChannelCounterTable - This table provides statistical
data for attached downstream channels, appropriate as input for load
usage calculations.
docsIfCmtsUpChannelCounterTable - This table provides statistical
data for attached upstream channels, appropriate as input for load
usage calculations.
3.2. Relationship to the Interfaces MIB
This section clarifies the relationship of this MIB to the
Interfaces MIB [RFC2863]. Several areas of correlation are addressed
in the following subsections. The implementer is referred to the
Interfaces MIB document in order to understand the general intent of
these areas.
3.2.1. Layering Model
Raftus Expires March 2004 [Page 7]
Internet Draft DOCSIS RF Interface MIB September 2003
An instance of ifEntry exists for each RF Downstream interface, for
each RF Upstream interface, for each Upstream logical Channel and
for each RF MAC layer.
The ifStackTable [RFC2863] MUST be implemented to identify
relationships among sub-interfaces.
The following example illustrates a CMTS MAC interface with one
downstream and two upstream interfaces.
| <== to network layer
+------------------ --+-------------------------------+
| RF MAC |
+--+------------------+------------------------+------+
| | |
+-------+-----+ +------+------+ +------+------+
| Downstream1 | | Upstream1 | | Upstream2 |
| | | | | |
+-------------+ ++-----------++ ++-----------++
| | | |
+----+----+ +----+----+ +----+----+ +----+----+
| Ch-1 | | Ch-2 | | Ch-1 | | Ch-2 |
|(A/TDMA) | |(S-CDMA) | |(A/TDMA) | |(S-CDMA) |
+---------+ +---------+ +---------+ +---------+
As can be seen from this example, the RF MAC interface is layered on
top of the downstream and upstream interfaces, and the RF Upstream
interface is layered on top of an Upstream Logical Channels.
In this example, the assignment of index values could be as follows:
ifIndex ifType Description
2 docsCableMaclayer(127) CATV MAC Layer
3 docsCableDownstream(128) CATV Downstream interface
4 docsCableUpstream(129) CATV Upstream interface
5 docsCableUpstream(129) CATV Upstream interface
6 docsCableUpstreamChannel(205) CATV Upstream Channel
7 docsCableUpstreamChannel(205) CATV Upstream Channel
8 docsCableUpstreamChannel(205) CATV Upstream Channel
9 docsCableUpstreamChannel(205) CATV Upstream Channel
The corresponding ifStack entries would then be:
| IfStackHigherLayer | ifStackLowerLayer |
| 0 | 2 |
| 2 | 3 |
| 2 | 4 |
| 2 | 5 |
| 4 | 6 |
| 4 | 7 |
Raftus Expires March 2004 [Page 8]
Internet Draft DOCSIS RF Interface MIB September 2003
| 5 | 8 |
| 5 | 9 |
| 3 | 0 |
| 6 | 0 |
| 7 | 0 |
| 8 | 0 |
| 9 | 0 |
The same interface model can also be used in Telephony or Telco
Return systems. A pure Telco Return system (Cable Modem as well as
Cable Modem Termination System) would not have upstream, but only
downstream cable channels. Systems supporting both Telco Return and
cable upstream channels can use the above model without
modification.
Telco Return Upstream channel(s) are handled by the appropriate
MIBs, such as PPP or Modem MIBs.
3.2.2. Virtual Circuits
This medium does not support virtual circuits and this area is not
applicable to this MIB.
3.2.3. ifTestTable
The ifTestTable is optional for Docsis CM/CMTS implementations, but
is not specifically influenced by the RF mib.
3.2.4. ifRcvAddressTable
The ifRcvAddressTable is optional for Docsis CM/CMTS
implementations, but is not specifically influenced by the RF mib.
3.2.5. ifEntry
This section documents only the differences from the requirements
specified in the Interfaces MIB. See that MIB for columns omitted
from the descriptions below.
3.2.5.1. ifEntry for Downstream interfaces
The ifEntry for Downstream interfaces supports the
ifGeneralInformationGroup and the ifPacketGroup of the Interfaces
MIB. This is an output only interface at the CMTS and all input
status counters - ifIn* - will return zero. This is an input only
interface at the CM and all output status counters - ifOut* - will
return zero.
3.2.5.1.1. ifEntry for Downstream interfaces in Cable Modem
Termination Systems
ifTable Comments
Raftus Expires March 2004 [Page 9]
Internet Draft DOCSIS RF Interface MIB September 2003
============== ===========================================
ifIndex Each RF Cable Downstream interface is represented
by an ifEntry.
ifType The IANA value of docsCableDownstream(128).
ifSpeed Return the speed of this downstream channel.
The returned value is the raw bandwidth in bits/s
of this interface. This is the symbol rate
multiplied with the number of bits per symbol.
ifHighSpeed Return the speed of this downstream channel.
The returned value is the raw bandwidth in
megabits/s of this interface. This is the symbol
rate multiplied with the number of bits per
symbol.
ifPhysAddress Return an empty string.
ifAdminStatus The administrative status of this interface.
ifOperStatus The current operational status of this interface.
ifMtu The size of the largest frame which can be
sent on this interface, specified in octets.
The value includes the length of the MAC header.
ifInOctets Return zero.
ifHCInOctets
ifInUcastPkts Return zero.
ifHCInUcastPkts
ifInMulticastPkts Return zero.
ifHCInMulticastPkts
ifInBroadcastPkts Return zero.
ifHCInBroadcastPkts
ifInDiscards Return zero.
ifInErrors Return zero.
ifInUnknownProtos Return zero.
ifOutOctets The total number of octets transmitted on this
ifHCOutOctets interface. This includes MAC packets as well as
data packets, and includes the length of the MAC
header.
ifOutUcastPkts The number of Unicast packets transmitted on this
ifHCOutUcastPkts interface. This includes MAC packets as well as
Raftus Expires March 2004 [Page 10]
Internet Draft DOCSIS RF Interface MIB September 2003
data packets.
ifOutMulticastPkts
ifHCOutMulticastPkts
Return the number of Multicast packets transmitted
on this interface.
This includes MAC packets as well as data packets.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return the number of broadcast packets transmitted
on this interface.
This includes MAC packets as well as data packets.
ifOutDiscards The total number of outbound packets which
were discarded. Possible reasons are:
buffer shortage.
ifOutErrors The number of packets which could not be
transmitted due to errors.
ifPromiscuousMode Return false.
3.2.5.1.2. ifEntry for Downstream interfaces in Cable Modems
ifTable Comments
============== ===========================================
ifIndex Each RF Cable Downstream interface is represented
by an ifEntry.
ifType The IANA value of docsCableDownstream(128).
ifSpeed Return the speed of this downstream channel.
The returned value the raw bandwidth in bits/s
of this interface. This is the symbol rate
multiplied with the number of bits per symbol.
ifHighSpeed Return the speed of this downstream channel.
The returned value the raw bandwidth in megabits/s
of this interface. This is the symbol rate
multiplied with the number of bits per symbol.
ifPhysAddress Return an empty string.
ifAdminStatus The administrative status of this interface.
ifOperStatus The current operational status of this interface.
ifMtu The size of the largest frame which can be
received from this interface, specified in octets.
The value includes the length of the MAC header.
Raftus Expires March 2004 [Page 11]
Internet Draft DOCSIS RF Interface MIB September 2003
ifInOctets The total number of octets received on this
ifHCInOctets interface. This includes data packets as well as
MAC packets, and includes the length of the
MAC header.
ifInUcastPkts The number of Unicast packets received on this
ifHCInUcastPkts interface. This includes data packets as well as
MAC packets.
ifInMulticastPkts
ifHCInMulticastPkts
Return the number of Multicast packets received
on this interface. This includes data packets as
well as MAC packets.
ifInBroadcastPkts
ifHCInBroadcastPkts
Return the number of Broadcast packets received
on this interface. This includes data packets
as well as MAC packets.
ifInDiscards The total number of received packets that have
been discarded.
The possible reasons are: buffer shortage.
ifInErrors The number of inbound packets that contained
errors preventing them from being deliverable
to higher layers.
Possible reasons are: MAC FCS error.
ifInUnknownProtos The number of frames with an unknown packet type.
These are MAC frames with an unknown packet type.
ifOutOctets Return zero.
ifHCOutOctets
ifOutUcastPkts Return zero.
ifHCOutUcastPkts
ifOutMulticastPkts
ifHCOutMulticastPkts
Return zero.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return zero.
ifOutDiscards Return zero.
ifOutErrors Return zero.
ifPromiscuousMode Refer to the Interfaces MIB.
Raftus Expires March 2004 [Page 12]
Internet Draft DOCSIS RF Interface MIB September 2003
3.2.5.2. ifEntry for Upstream interfaces
Each supported interface of the type docsCableUpstream(129) must
have a corresponding ifEntry.
The ifEntry for Upstream interfaces supports the
ifGeneralInformationGroup and the ifPacketGroup of the Interfaces
MIB. This is an input only interface at the CMTS and all output
status counters - ifOut* - will return zero. This is an output only
interface at the CM and all input status counters - ifIn* - will
return zero.
3.2.5.2.1. ifEntry for Upstream interfaces in Cable Modem Termination
Systems
ifTable Comments
============== ===========================================
ifIndex Each RF Cable Upstream interface is represented
by an ifEntry.
ifType The IANA value of docsCableUpstream (129).
ifSpeed Return the maximum channel throughput (not payload
throughput) supported by the interface.
The maximum throughput is calculated for the case
where upstream channels are configured to maximize
interface throughput.
ifHighSpeed Return the maximum channel throughput (not payload
throughput) supported by the interface.
The maximum throughput is calculated for the case
where upstream channels are configured to maximize
interface throughput. Units for this object are
(1/1 000 000) * IfSpeed.
ifPhysAddress Return an empty string.
ifAdminStatus The administrative status of this interface.
This reflect the total status of all the channels
under this interface. So if at least one channel
has a physical connection this interface has
connection. Any SNMP SET on this interface will
cause a SET to all the channels under this
interface.
ifOperStatus The current operational status of this interface.
This reflects the total status of all the channels
under this interface. So if at least one channel
has a physical connection this interface has
connection.
Raftus Expires March 2004 [Page 13]
Internet Draft DOCSIS RF Interface MIB September 2003
ifMtu The size of the largest frame which can be
transmitted on this interface, specified in
octets. The value includes the length of the MAC
header. This is the maximum of all the ifMtu of
all the channels under this interface.
ifInOctets
ifHCInOctets The total (sum) number of octets received on all
the Upstream channels under this
interface. This includes data packets as well as
MAC packets, and includes the length of the
MAC header.
ifInUcastPkts
ifHCInUcastPkts The total number of Unicast packets received on
all the upstream channels under this
interface. This includes data packets as well as
MAC packets.
ifInMulticastPkts
ifHCInMulticastPkts
Return the total number of Multicast packets
received on all the Upstream channels under this
interface. This includes data packets as well as
MAC layer packets.
ifInBroadcastPkts
ifHCInBroadcastPkts
Return the total number of Broadcast packets
received on all the Upstream channels under this
interface. This includes data packets as well as
MAC packets.
ifInDiscards The total number of received packets, which have
been discarded on all the Upstream channels under
this interface.
The possible reasons are: buffer shortage.
ifInErrors The total number of inbound packets that contained
errors preventing them from being deliverable
to higher layers.
Possible reasons are: MAC FCS error.
ifInUnknownProtos The total number of frames with an unknown packet
type. These are MAC frames with an unknown packet
type.
ifOutOctets Return zero.
ifHCOutOctets
ifOutUcastPkts Return zero.
Raftus Expires March 2004 [Page 14]
Internet Draft DOCSIS RF Interface MIB September 2003
ifHCOutOctets
ifOutMulticastPkts
ifHCOutMulticastPkts
Return zero.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return zero.
ifOutDiscards Return zero.
ifOutErrors Return zero.
3.2.5.2.2. ifEntry for Upstream interfaces in Cable Modems
ifTable Comments
============== ===========================================
ifIndex Each RF Cable Upstream interface is represented
by an ifEntry.
ifType The IANA value of docsCableUpstream (129).
ifSpeed Return the speed of this upstream interface.
The returned value is the raw bandwidth
in bits/s of this interface.
ifHighSpeed Return the speed of this upstream interface.
The returned value is the raw bandwidth
in megabits/s of this interface.
ifPhysAddress Return an empty string.
ifAdminStatus The administrative status of this interface.
ifOperStatus The current operational status of this interface.
ifMtu The size of the largest frame which can be
transmitted on this interface, specified in
octets. The value includes the length of the MAC
header.
ifInOctets Return zero.
ifHCInOctets
ifInUcastPkts Return zero.
ifHCInUcastPkts
ifInMulticastPkts Return zero.
ifHCInMulticastPkts
Raftus Expires March 2004 [Page 15]
Internet Draft DOCSIS RF Interface MIB September 2003
ifInBroadcastPkts Return zero.
ifHCInBroadcastPkts
ifInDiscards Return zero.
ifInErrors Return zero.
ifInUnknownProtos Return zero.
ifOutOctets The total number of octets transmitted on this
ifHCOutOctets interface. This includes MAC packets as well as
data packets, and includes the length of the MAC
header.
ifOutUcastPkts The number of Unicast packets transmitted on this
ifHCOutUcastPkts interface. This includes MAC packets as well as
data packets.
ifOutMulticastPkts
ifHCOutMulticastPkts
Return the number of Multicast packets transmitted
on this interface.
This includes MAC packets as well as data packets.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return the number of broadcast packets transmitted
on this interface.
This includes MAC packets as well as data packets.
ifOutDiscards The total number of outbound packets which
were discarded. Possible reasons are:
buffer shortage.
ifOutErrors The number of packets which could not be
transmitted due to errors.
ifPromiscuousMode Return false.
3.2.5.3. ifEntry for Upstream channels
Each supported channel of the type docsCableUpstreamChannel(205)
must have a corresponding ifEntry.
The ifEntry for Upstream channels supports the
ifGeneralInformationGroup and the ifPacketGroup of the Interfaces
MIB. This is an input only interface at the CMTS and all output
status counters - ifOut* - will return zero. At the time of this mib
creation, DOCSIS CMs are not required to support logical upstream
channels.
3.2.5.3.1. ifEntry for Upstream Channels in Cable Modem Termination
Raftus Expires March 2004 [Page 16]
Internet Draft DOCSIS RF Interface MIB September 2003
Systems
ifTable Comments
============== ===========================================
ifIndex Each RF Cable Upstream channel is represented
by an ifEntry.
ifType The IANA value of docsCableUpstreamChannel (205).
ifSpeed Return the speed of this upstream channel.
The returned value is the raw bandwidth
in bits/s of this channel.
ifHighSpeed Return the speed of this upstream channel.
The returned value is the raw bandwidth
in megabits/s of this channel.
ifPhysAddress Return an empty string.
ifAdminStatus The administrative status of this interface.
ifOperStatus The current operational status of this interface.
ifMtu The size of the largest frame which can be
received on this interface, specified in octets.
The value includes the length of the MAC header.
ifInOctets The total number of octets received on this
interface. This includes data packets as well as
MAC packets, and includes the length of the
MAC header.
ifInUcastPkts The number of Unicast packets received on this
ifHCInUcastPkts interface. This includes data packets as well as
MAC packets.
ifInMulticastPkts
ifHCInMulticastPkts
Return the number of Multicast packets received
on this interface. This includes data packets as
well as MAC layer packets.
ifInBroadcastPkts
ifHCInBroadcastPkts
Return the number of Broadcast packets received
on this interface. This includes data packets
as well as MAC packets.
ifInDiscards The total number of received packets that have
been discarded.
The possible reasons are: buffer shortage.
Raftus Expires March 2004 [Page 17]
Internet Draft DOCSIS RF Interface MIB September 2003
ifInErrors The number of inbound packets that contained
errors preventing them from being deliverable
to higher layers.
Possible reasons are: MAC FCS error.
ifInUnknownProtos The number of frames with an unknown packet type.
These are MAC frames with an unknown packet type.
ifOutOctets Return zero.
ifHCOutOctets
ifOutUcastPkts Return zero.
ifHCOutUcastPkts
ifOutMulticastPkts
ifHCOutMulticastPkts
Return zero.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return zero.
ifOutDiscards Return zero.
ifOutErrors Return zero.
3.2.5.4. ifEntry for the MAC Layer
The ifEntry for the MAC Layer supports the ifGeneralInformationGroup
and the ifPacketGroup of the Interfaces MIB. This interface
provides an aggregate view of status for the lower level Downstream
and Upstream interfaces.
ifTable Comments
============== ===========================================
ifIndex Each RF Cable MAC layer entity is represented
by an ifEntry.
ifType The IANA value of docsCableMaclayer(127).
ifSpeed Return zero.
ifPhysAddress Return the physical address of this interface.
ifAdminStatus The administrative status of this interface.
ifOperStatus The current operational status of the MAC
layer interface.
ifHighSpeed Return zero.
Raftus Expires March 2004 [Page 18]
Internet Draft DOCSIS RF Interface MIB September 2003
ifMtu Return 1500.
ifInOctets The total number of data octets received on this
ifHCInOctets interface, targeted for upper protocol layers.
ifInUcastPkts The number of Unicast packets received on this
ifHCInUcastPkts interface, targeted for upper protocol layers.
ifInMulticastPkts
ifHCInMulticastPkts
Return the number of Multicast packets received
on this interface, targeted for upper protocol
layers.
ifInBroadcastPkts
ifHCInBroadcastPkts
Return the number of Broadcast packets received
on this interface, targeted for upper protocol
layers.
ifInDiscards The total number of received packets that have
been discarded.
The possible reasons are: buffer shortage.
ifInErrors The number of inbound packets that contained
errors preventing them from being deliverable
to higher layers.
Possible reasons are: data packet FCS error,
invalid MAC header.
ifInUnknownProtos The number of frames with an unknown packet type.
This is the number of data packets targeted for
upper protocol layers with an unknown packet type.
ifOutOctets The total number of octets, received from upper
ifHCOutOctets protocol layers and transmitted on this interface.
ifOutUcastPkts The number of Unicast packets, received from upper
ifHCOutUcastPkts protocol layers and transmitted on this interface.
ifOutMulticastPkts
ifHCOutMulticastPkts
Return the number of Multicast packets received
from upper protocol layers and transmitted on this
interface.
ifOutBroadcastPkts
ifHCOutBroadcastPkts
Return the number of broadcast packets received
from upper protocol layers and transmitted on this
Raftus Expires March 2004 [Page 19]
Internet Draft DOCSIS RF Interface MIB September 2003
interface.
ifOutDiscards The total number of outbound packets which
were discarded. Possible reasons are:
buffer shortage.
ifOutErrors The number of packets which could not be
transmitted due to errors.
ifPromiscuousMode Refer to the Interfaces MIB.
4. Definitions
DOCS-IF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
-- do not import BITS,
Unsigned32,
Integer32,
Counter32,
Counter64,
TimeTicks,
IpAddress,
transmission
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
MacAddress,
RowStatus,
TruthValue,
TimeInterval,
TimeStamp
FROM SNMPv2-TC
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF
ifIndex, InterfaceIndexOrZero
FROM IF-MIB
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB
IANAifType
FROM IANAifType-MIB;
docsIfMib MODULE-IDENTITY
LAST-UPDATED "200309100000Z" -- September 10, 2003
ORGANIZATION "IETF IPCDN Working Group"
CONTACT-INFO
" David Raftus
Raftus Expires March 2004 [Page 20]
Internet Draft DOCSIS RF Interface MIB September 2003
Postal: Terayon Communications
340 Terry Fox Drive, Suite 202
Ottawa Ontario
Canada
Phone: +1 613 592 1052 ext.222
E-mail: david.raftus@terayon.com
IETF IPCDN Working Group
General Discussion: ipcdn@ietf.org
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy, Richard_Woundy@cable.comcast.com
Jean-Francois Mule, jf.mule@cablelabs.com"
DESCRIPTION
"This is the MIB Module for DOCSIS 2.0 compliant Radio
Frequency (RF) interfaces in Cable Modems (CM) and
Cable Modem Termination Systems (CMTS)."
REVISION "200309100000Z"
DESCRIPTION
"pre-RFC draft v7:
Modified by David Raftus to return name to pre v6 title
DOCS-IF-MIB, to clarify descriptive wording of various
objects, tables and methodologies, to add new objects to
count UCC transactions, to add enumeration values to
docsIfCmtsModPreambleType and docsIfCmtsCmStatusValue, to
to add new object to indicate the last update time of
docsIfCmtsCmStatusValueLastUpdate, to update references to
the latest Docsis versions.
pre-RFC draft v6:
Modified by David Raftus to update references, boilerplate
to format suggested by IPCDN workgroup. Also clarified
descriptions of some objects, added size constraints to
selected objects to fix compiler warnings.
pre-RFC draft v5:
Modified by David Raftus to add channel utilization
related objects, upstream channel equalization related
objects, a cmts upstream minislot counter table, a cmts
downstream byte counter table, 64 bit versions of existing
32 bit docsIfSigQTable objects, and perform some editorial
adjustments.
pre-RFC draft v4:
Modified by David Raftus to fix docsIfUpChannelWidth range
in compliance statements to accommodate 6.4Mhz channel at
5.12 Msymbol/sec. Also adjusted description of
docsIfUpChannelStatus to use correct rowStatus
terminology.
pre-RFC draft v3:
Modified by David Raftus to add new textual convention
describing upstream modulation status. Also clarified
some object descriptions, fixed error in
docsIfSignalQualityEntry, fixed upstreamTable compliance
statements.
Raftus Expires March 2004 [Page 21]
Internet Draft DOCSIS RF Interface MIB September 2003
pre-RFC draft v2:
Modified by David Raftus to add capability to adjust
and verify upstream channel parameters as a group.
Also adjusted syntax and clarified descriptions of
selected objects.
pre-RFC draft v1:
Modified by Aviv Goren and David Raftus to accommodate
Docsis 2.0 Advanced Phy capabilities, as well as to
incorporate objects from the docsIfExt mib.
Modified by Rich Woundy to use IPv6-friendly
address objects, to accommodate EuroDOCSIS, and
to correct the SYNTAX of various objects."
REVISION "199908190000Z"
DESCRIPTION
"Initial Version, published as RFC 2670.
Modified by Mike StJohns to fix problems identified by
the first pass of the MIB doctor. Of special note,
docsIfRangingResp and docsIfCmtsInsertionInterval were
obsoleted and replaced by other objects with the same
functionality, but more appropriate SYNTAX."
::= { transmission 127 }
-- Textual Conventions
TenthdBmV ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d-1"
STATUS current
DESCRIPTION
"This data type represents power levels that are normally
expressed in dBmV. Units are in tenths of a dBmV;
for example, 5.1 dBmV will be represented as 51."
SYNTAX Integer32
TenthdB ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d-1"
STATUS current
DESCRIPTION
"This data type represents power levels that are normally
expressed in dB. Units are in tenths of a dB;
for example, 5.1 dB will be represented as 51."
SYNTAX Integer32
DocsisVersion ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the DOCSIS version number."
SYNTAX INTEGER {
docsis10 (1),
docsis11 (2),
docsis20 (3)
}
Raftus Expires March 2004 [Page 22]
Internet Draft DOCSIS RF Interface MIB September 2003
DocsisQosVersion ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the quality of service level."
SYNTAX INTEGER {
docsis10 (1),
docsis11 (2)
}
DocsisUpstreamType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the DOCSIS Upstream Channel Type."
SYNTAX INTEGER {
unknown (0),
tdma (1),
atdma (2),
scdma (3),
tdmaAndAtdma (4)
}
DocsisUpstreamTypeStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the DOCSIS Upstream Channel Type Status.
The shared channel indicator type is not valid, since
this type is used to specifically identify PHY mode."
SYNTAX INTEGER {
unknown (0),
tdma (1),
atdma (2),
scdma (3)
}
docsIfMibObjects OBJECT IDENTIFIER ::= { docsIfMib 1 }
docsIfBaseObjects OBJECT IDENTIFIER ::= { docsIfMibObjects 1 }
docsIfCmObjects OBJECT IDENTIFIER ::= { docsIfMibObjects 2 }
docsIfCmtsObjects OBJECT IDENTIFIER ::= { docsIfMibObjects 3 }
--
-- BASE GROUP
--
--
-- The following table is implemented on both the Cable Modem (CM)
-- and the Cable Modem Termination System (CMTS). This table is
-- read only for the CM.
--
docsIfDownstreamChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfDownstreamChannelEntry
Raftus Expires March 2004 [Page 23]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the attributes of downstream
channels (frequency bands)."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-12 and Table 6-13."
::= { docsIfBaseObjects 1 }
docsIfDownstreamChannelEntry OBJECT-TYPE
SYNTAX DocsIfDownstreamChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry provides a list of attributes for a single
Downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128)."
INDEX { ifIndex }
::= { docsIfDownstreamChannelTable 1 }
DocsIfDownstreamChannelEntry ::= SEQUENCE {
docsIfDownChannelId Integer32,
docsIfDownChannelFrequency Integer32,
docsIfDownChannelWidth Integer32,
docsIfDownChannelModulation INTEGER,
docsIfDownChannelInterleave INTEGER,
docsIfDownChannelPower TenthdBmV,
docsIfDownChannelAnnex INTEGER
}
docsIfDownChannelId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Cable Modem Termination System (CMTS) identification
of the downstream channel within this particular MAC
interface. If the interface is down, the object returns
the most current value. If the downstream channel ID is
unknown, this object returns a value of 0."
::= { docsIfDownstreamChannelEntry 1 }
docsIfDownChannelFrequency OBJECT-TYPE
SYNTAX Integer32 (0..1000000000)
UNITS "hertz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The center of the downstream frequency associated with
Raftus Expires March 2004 [Page 24]
Internet Draft DOCSIS RF Interface MIB September 2003
this channel. This object will return the current tuner
frequency. If a CMTS provides IF output, this object
will return 0, unless this CMTS is in control of the
final downstream RF frequency. See the associated
compliance object for a description of valid frequencies
that may be written to this object."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Tables 4-1, 6-14."
::= { docsIfDownstreamChannelEntry 2 }
docsIfDownChannelWidth OBJECT-TYPE
SYNTAX Integer32 (0..16000000)
UNITS "hertz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The bandwidth of this downstream channel. Most
implementations are expected to support a channel width
of 6 MHz (North America) and/or 8 MHz (Europe). See the
associated compliance object for a description of the
valid channel widths for this object."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-14."
::= { docsIfDownstreamChannelEntry 3 }
docsIfDownChannelModulation OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
qam64(3),
qam256(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The modulation type associated with this downstream
channel. If the interface is down, this object either
returns the configured value (CMTS), the most current
value (CM), or the value of unknown(1). See the
associated conformance object for write conditions and
limitations. See the reference for specifics on the
modulation profiles implied by qam64 and qam256."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-14."
::= { docsIfDownstreamChannelEntry 4 }
Raftus Expires March 2004 [Page 25]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfDownChannelInterleave OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
taps8Increment16(3),
taps16Increment8(4),
taps32Increment4(5),
taps64Increment2(6),
taps128Increment1(7),
taps12increment17(8)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Forward Error Correction (FEC) interleaving used
for this downstream channel.
Values are defined as follows:
taps8Increment16(3): protection 5.9/4.1 usec,
latency .22/.15 msec
taps16Increment8(4): protection 12/8.2 usec,
latency .48/.33 msec
taps32Increment4(5): protection 24/16 usec,
latency .98/.68 msec
taps64Increment2(6): protection 47/33 usec,
latency 2/1.4 msec
taps128Increment1(7): protection 95/66 usec,
latency 4/2.8 msec
taps12increment17(8): protection 18/14 usec,
latency 0.43/0.32 msec
taps12increment17 is implemented in
conformance with EuroDOCSIS
document 'Adapted MIB-definitions -
and a clarification for
MPEG-related issues - for
EuroDOCSIS cable modem systems' by
tComLabs and should only be used
for a EuroDOCSIS MAC interface.
If the interface is down, this object either returns
the configured value (CMTS), the most current value (CM),
or the value of unknown(1).
The value of other(2) is returned if the interleave
is known but not defined in the above list.
See the associated conformance object for write
conditions and limitations. See the reference for the FEC
configuration described by the setting of this object."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-13."
::= { docsIfDownstreamChannelEntry 5 }
Raftus Expires March 2004 [Page 26]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfDownChannelPower OBJECT-TYPE
SYNTAX TenthdBmV
UNITS "dBmV"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"At the CMTS, the operational transmit power. At the CM,
the received power level.
If the interface is down, this object either returns
the configured value (CMTS), the most current value (CM)
or the value of 0. See the associated conformance object
for write conditions and limitations. See the reference
for recommended and required power levels."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-15."
::= { docsIfDownstreamChannelEntry 6 }
docsIfDownChannelAnnex OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
annexA(3),
annexB(4),
annexC(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J83 is used.
annexC : Annex C from ITU-J83 is used.
AnnexB is used for DOCSIS implementations"
REFERENCE
"Document Adapted MIB-definitions and a clarification for
MPEG-related issues for EuroDOCSIS cable modem systems
v1.01, tComLabs, May 2000, Section 2.2"
::= { docsIfDownstreamChannelEntry 7 }
--
-- The following table is implemented on both the CM and the CMTS.
-- For the CM, only attached channels appear in the table. For the
-- CM, this table is read only as well.
--
docsIfUpstreamChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfUpstreamChannelEntry
MAX-ACCESS not-accessible
STATUS current
Raftus Expires March 2004 [Page 27]
Internet Draft DOCSIS RF Interface MIB September 2003
DESCRIPTION
"This table describes the attributes of attached upstream
channels."
::= { docsIfBaseObjects 2 }
docsIfUpstreamChannelEntry OBJECT-TYPE
SYNTAX DocsIfUpstreamChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of attributes for a single upstream channel. For
Docsis 2.0 CMTSs, an entry in this table exists for
each ifEntry with an ifType of docsCableUpstreamChannel
(205).
For Docsis 1.x CM/CMTSs and Docsis 2.0 CMs, an entry in
this table exists for each ifEntry with an ifType of
docsCableUpstreamInterface (129)."
INDEX { ifIndex }
::= { docsIfUpstreamChannelTable 1 }
DocsIfUpstreamChannelEntry ::= SEQUENCE {
docsIfUpChannelId Integer32,
docsIfUpChannelFrequency Integer32,
docsIfUpChannelWidth Integer32,
docsIfUpChannelModulationProfile Unsigned32,
docsIfUpChannelSlotSize Unsigned32,
docsIfUpChannelTxTimingOffset Unsigned32,
docsIfUpChannelRangingBackoffStart Integer32,
docsIfUpChannelRangingBackoffEnd Integer32,
docsIfUpChannelTxBackoffStart Integer32,
docsIfUpChannelTxBackoffEnd Integer32,
docsIfUpChannelScdmaActiveCodes Unsigned32,
docsIfUpChannelScdmaCodesPerSlot Integer32,
docsIfUpChannelScdmaFrameSize Unsigned32,
docsIfUpChannelScdmaHoppingSeed Unsigned32,
docsIfUpChannelType DocsisUpstreamType,
docsIfUpChannelCloneFrom InterfaceIndexOrZero,
docsIfUpChannelUpdate TruthValue,
docsIfUpChannelStatus RowStatus,
docsIfUpChannelPreEqEnable TruthValue
}
docsIfUpChannelId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The CMTS identification of the upstream channel."
::= { docsIfUpstreamChannelEntry 1 }
docsIfUpChannelFrequency OBJECT-TYPE
SYNTAX Integer32 (0..1000000000)
Raftus Expires March 2004 [Page 28]
Internet Draft DOCSIS RF Interface MIB September 2003
UNITS "hertz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The center of the frequency band associated with this
upstream interface. This object returns 0 if the frequency
is undefined or unknown. Minimum permitted upstream
frequency is 5,000,000 Hz for current technology. See
the associated conformance object for write conditions
and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 4-2."
::= { docsIfUpstreamChannelEntry 2 }
docsIfUpChannelWidth OBJECT-TYPE
SYNTAX Integer32 (0..64000000)
UNITS "hertz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The bandwidth of this upstream interface. This object
returns 0 if the interface width is undefined or unknown.
Minimum permitted interface width is 200,000 Hz currently.
See the associated conformance object for write conditions
and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-12."
::= { docsIfUpstreamChannelEntry 3 }
docsIfUpChannelModulationProfile OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An entry identical to the docsIfModIndex in the
docsIfCmtsModulationTable that describes this channel.
This channel is further instantiated there by a grouping
of interval usage codes which together fully describe the
channel modulation. This object returns 0 if the
docsIfCmtsModulationTable entry does not exist or
docsIfCmtsModulationTable is empty. See
the associated conformance object for write conditions
and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
Raftus Expires March 2004 [Page 29]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfUpstreamChannelEntry 4 }
docsIfUpChannelSlotSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Applicable to TDMA and ATDMA channel types only.
The number of 6.25 microsecond ticks in each upstream
mini-slot. Returns zero if the value is undefined, unknown
or in case of an SCDMA channel.
See the associated conformance object for write
conditions and limitations. "
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.1.2.4."
::= { docsIfUpstreamChannelEntry 5 }
docsIfUpChannelTxTimingOffset OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CM, a measure of the current round trip time
obtained from the ranging offset (initial ranging offset +
ranging offset adjustments).
At the CMTS, the maximum of timing offset, among all the
CMs that are/were present on the channel, taking into
account all ( initial + periodic ) timing offset
corrections that were sent for each of the CMs. Generally,
these measurements are positive, but if the measurements
are negative, the value of this object is zero. Used for
timing of CM upstream transmissions to ensure synchronized
arrivals at the CMTS.
Units are in terms of (6.25 microseconds/64)."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.18."
::= { docsIfUpstreamChannelEntry 6 }
docsIfUpChannelRangingBackoffStart OBJECT-TYPE
SYNTAX Integer32 (0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The initial random backoff window to use when retrying
Ranging Requests. Expressed as a power of 2. A value of 16
at the CMTS indicates that a proprietary adaptive retry
mechanism is to be used. See the associated conformance
object for write conditions and limitations."
Raftus Expires March 2004 [Page 30]
Internet Draft DOCSIS RF Interface MIB September 2003
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.4."
::= { docsIfUpstreamChannelEntry 7 }
docsIfUpChannelRangingBackoffEnd OBJECT-TYPE
SYNTAX Integer32 (0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The final random backoff window to use when retrying
Ranging Requests. Expressed as a power of 2. A value of 16
at the CMTS indicates that a proprietary adaptive retry
mechanism is to be used. See the associated conformance
object for write conditions and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.4."
::= { docsIfUpstreamChannelEntry 8 }
docsIfUpChannelTxBackoffStart OBJECT-TYPE
SYNTAX Integer32 (0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The initial random backoff window to use when retrying
transmissions. Expressed as a power of 2. A value of 16
at the CMTS indicates that a proprietary adaptive retry
mechanism is to be used. See the associated conformance
object for write conditions and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.4."
::= { docsIfUpstreamChannelEntry 9 }
docsIfUpChannelTxBackoffEnd OBJECT-TYPE
SYNTAX Integer32 (0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The final random backoff window to use when retrying
transmissions. Expressed as a power of 2. A value of 16
at the CMTS indicates that a proprietary adaptive retry
mechanism is to be used. See the associated conformance
object for write conditions and limitations."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.4."
Raftus Expires March 2004 [Page 31]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfUpstreamChannelEntry 10 }
docsIfUpChannelScdmaActiveCodes OBJECT-TYPE
SYNTAX Unsigned32 (0 | 64..128)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Applicable for SCDMA channel types only.
Number of active codes. Returns zero for
Non-SCDMA channel types. Note that legal
values from 64..128 MUST be non-prime."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.11.2.1."
::= { docsIfUpstreamChannelEntry 11 }
docsIfUpChannelScdmaCodesPerSlot OBJECT-TYPE
SYNTAX Integer32(0 | 2..32)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Applicable for SCDMA channel types only.
The number of SCDMA codes per mini-slot.
Returns zero if the value is undefined, unknown or in
case of a TDMA or ATDMA channel."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.11.2.1."
::= { docsIfUpstreamChannelEntry 12 }
docsIfUpChannelScdmaFrameSize OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Applicable for SCDMA channel types only.
SCDMA Frame size in units of spreading intervals.
This value returns zero for non SCDMA Profiles."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.12."
::= { docsIfUpstreamChannelEntry 13 }
docsIfUpChannelScdmaHoppingSeed OBJECT-TYPE
SYNTAX Unsigned32 (0..32767)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Applicable for SCDMA channel types only.
Raftus Expires March 2004 [Page 32]
Internet Draft DOCSIS RF Interface MIB September 2003
15 bit seed used for code hopping sequence initialization.
Returns zero for non-SCDMA channel types."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.14.1."
::= { docsIfUpstreamChannelEntry 14 }
docsIfUpChannelType OBJECT-TYPE
SYNTAX DocsisUpstreamType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the Upstream channel type.
Given the channel type, other channel attributes can be
checked for value validity at the time of entry creation
and update."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.1."
::= { docsIfUpstreamChannelEntry 15 }
docsIfUpChannelCloneFrom OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Intended for use when a temporary inactive upstream table
row is created for the purpose of manipulating parameters
for an active row. Refer to the descriptions of
docsIfUpChannelStatus and docsIfUpChannelUpdate for
details of this procedure. This object contains the
ifIndex value of the active upstream row whose parameters
are to be adjusted.
Although this object was created to facilitate SCDMA
parameter adjustment, it may also be used at the vendor's
discretion for non-SCDMA parameter adjustment.
This object must contain a value of zero for active
upstream rows."
::= { docsIfUpstreamChannelEntry 16 }
docsIfUpChannelUpdate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Used to perform the transfer of adjusted SCDMA parameters
from the temporary upstream row to the active upstream row
indicated by the docsIfUpChannelCloneFrom object. The
transfer is initiated through an SNMP SET of TRUE to this
object. The SNMP SET will fail with a GEN_ERROR (snmpv1)
Raftus Expires March 2004 [Page 33]
Internet Draft DOCSIS RF Interface MIB September 2003
or COMMIT_FAILED_ERROR (snmpv2c/v3) if the adjusted
SCDMA parameter values are not compatible with each other.
Although this object was created to facilitate SCDMA
parameter adjustment, it may also be used at the vendor's
discretion for non-SCDMA parameter adjustment.
An SNMP GET of this object always returns FALSE."
::= { docsIfUpstreamChannelEntry 17 }
docsIfUpChannelStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is generally intended to be used for the
creation of a temporary inactive upstream row for the
purpose of adjusting channel parameters of an active
upstream row.
The recommended procedure is:
1) Create an inactive row through an SNMP SET using
createAndWait(5). Use an ifIndex value outside the
operational range of the system.
2) Set the docsIfUpChannelCloneFrom field to the ifIndex
value of the active row whose parameters require
adjustment.
3) Adjust the parameter values using the new
temporary inactive row. Ensure all parameters contain
desired values before proceeding to step 4.
4) Update the active row by setting object
docsIfUpChannelUpdate to TRUE. This SET will fail if
the adjusted parameters are not compatible with
each other.
5) Delete the temporary row through an SNMP SET using
DELETE.
The following restrictions apply to this object:
1) This object must contain a value of active(1) for
active rows.
2) Temporary inactive rows must be created using
createAndWait(5).
3) The only possible status change of a row created using
createAndWait(5) (ie notInService(2)) is to destroy(6).
These temporary rows must never become active.
4) A status transition from active (1) to destroy (6) is
not permitted. Entries with docsIfUpChannelStatus set
to active(1) are logically linked to a physical
interface, not temporarily created to clone parameters.
The Interface MIB [RFC2863] ifAdminStatus should be
used to take an Upstream Channel offline.
Although this object was created to facilitate SCDMA
parameter adjustment, it may also be used at the vendor's
Raftus Expires March 2004 [Page 34]
Internet Draft DOCSIS RF Interface MIB September 2003
discretion for non-SCDMA parameter adjustment."
::= { docsIfUpstreamChannelEntry 18 }
docsIfUpChannelPreEqEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"At the CMTS, used to enable or disable pre-equalization on
the upstream channel represented by this table instance.
At the CM, this object is read-only and reflects the
status of pre-equalization as represented in the RNG-RSP.
Pre-equalization is considered enabled at the CM if a
RNG-RSP with pre-equalization data has been received at
least once since the last mac reinit."
::= { docsIfUpstreamChannelEntry 19 }
-- The following table describes the attributes of each class of
-- service. The entries in this table are referenced from the
-- docsIfServiceEntries. They exist as a separate table in order to
-- reduce redundant information in docsIfServiceTable.
--
-- This table is implemented at both the CM and the CMTS.
-- The CM need only maintain entries for the classes of service
-- referenced by its docsIfServiceTable.
--
docsIfQosProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes for each class of service."
::= { docsIfBaseObjects 3 }
docsIfQosProfileEntry OBJECT-TYPE
SYNTAX DocsIfQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes for a single class of service.
If implemented as read-create in the Cable Modem
Termination System, creation of entries in this table is
controlled by the value of
docsIfCmtsQosProfilePermissions.
If implemented as read-only, entries are created based
Raftus Expires March 2004 [Page 35]
Internet Draft DOCSIS RF Interface MIB September 2003
on information in REG-REQ MAC messages received from
Cable Modems (Cable Modem Termination System
implementation), or based on information extracted from
the TFTP option file (Cable Modem implementation).
In the Cable Modem Termination system, read-only entries
are removed if no longer referenced by
docsIfCmtsServiceTable.
An entry in this table must not be removed while it is
referenced by an entry in docsIfCmServiceTable (Cable
Modem) or docsIfCmtsServiceTable (Cable Modem Termination
System).
An entry in this table should not be changeable while
it is referenced by an entry in docsIfCmtsServiceTable.
If this table is created automatically, there should only
be a single entry for each Class of Service. Multiple
entries with the same Class of Service parameters are not
recommended."
INDEX { docsIfQosProfIndex }
::= { docsIfQosProfileTable 1 }
DocsIfQosProfileEntry ::= SEQUENCE {
docsIfQosProfIndex Integer32,
docsIfQosProfPriority Integer32,
docsIfQosProfMaxUpBandwidth Integer32,
docsIfQosProfGuarUpBandwidth Integer32,
docsIfQosProfMaxDownBandwidth Integer32,
docsIfQosProfMaxTxBurst Integer32, -- Deprecated
docsIfQosProfBaselinePrivacy TruthValue,
docsIfQosProfStatus RowStatus,
docsIfQosProfMaxTransmitBurst Integer32
}
docsIfQosProfIndex OBJECT-TYPE
SYNTAX Integer32 (1..16383)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies an entry
in the docsIfQosProfileTable."
::= { docsIfQosProfileEntry 1 }
docsIfQosProfPriority OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A relative priority assigned to this service when
allocating bandwidth. Zero indicates lowest priority
and seven indicates highest priority.
Raftus Expires March 2004 [Page 36]
Internet Draft DOCSIS RF Interface MIB September 2003
Interpretation of priority is device-specific.
MUST NOT be changed while this row is active."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Appendix C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 2 }
docsIfQosProfMaxUpBandwidth OBJECT-TYPE
SYNTAX Integer32 (0..100000000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum upstream bandwidth, in bits per second,
allowed for a service with this service class.
Zero if there is no restriction of upstream bandwidth.
MUST NOT be changed while this row is active."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Appendix C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 3 }
docsIfQosProfGuarUpBandwidth OBJECT-TYPE
SYNTAX Integer32 (0..100000000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum guaranteed upstream bandwidth, in bits per second,
allowed for a service with this service class.
MUST NOT be changed while this row is active."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Appendix C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 4 }
docsIfQosProfMaxDownBandwidth OBJECT-TYPE
SYNTAX Integer32 (0..100000000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum downstream bandwidth, in bits per second,
allowed for a service with this service class.
Zero if there is no restriction of downstream bandwidth.
MUST NOT be changed while this row is active."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Raftus Expires March 2004 [Page 37]
Internet Draft DOCSIS RF Interface MIB September 2003
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Appendix C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 5 }
docsIfQosProfMaxTxBurst OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The maximum number of mini-slots that may be requested
for a single upstream transmission.
A value of zero means there is no limit.
MUST NOT be changed while this row is active.
This object has been deprecated and replaced by
docsIfQosProfMaxTransmitBurst, to fix a mismatch
of the units and value range with respect to the DOCSIS
Maximum Upstream Channel Transmit Burst Configuration
Setting."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 6 }
docsIfQosProfBaselinePrivacy OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether Baseline Privacy is enabled for this
service class.
MUST NOT be changed while this row is active."
DEFVAL { false }
::= { docsIfQosProfileEntry 7 }
docsIfQosProfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is object is to used to create or delete rows in
this table. This object MUST NOT be changed from active
while the row is referenced by the any entry in either
docsIfCmServiceTable (on the CM), or the
docsIfCmtsServiceTable (on the CMTS)."
::= { docsIfQosProfileEntry 8 }
docsIfQosProfMaxTransmitBurst OBJECT-TYPE
SYNTAX Integer32 (0..65535)
Raftus Expires March 2004 [Page 38]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of bytes that may be requested for a
single upstream transmission. A value of zero means there
is no limit. Note: This value does not include any
physical layer overhead.
MUST NOT be changed while this row is active."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Appendix C.1.1.4."
DEFVAL { 0 }
::= { docsIfQosProfileEntry 9 }
docsIfSignalQualityTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfSignalQualityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"At the CM, describes the PHY signal quality of downstream
channels. At the CMTS, describes the PHY signal quality of
upstream channels. At the CMTS, this table may exclude
contention intervals."
::= { docsIfBaseObjects 4 }
docsIfSignalQualityEntry OBJECT-TYPE
SYNTAX DocsIfSignalQualityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"At the CM, describes the PHY characteristics of a
downstream channel. At the CMTS, describes the PHY signal
quality of an upstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128) for Cable Modems.
For Docsis 1.1 Cable Modem Termination Systems, an entry
exists for each ifEntry with an ifType of
docsCableUpstream (129).
For Docsis 2.0 Cable Modem Termination Systems, an entry
exists for each ifEntry with an ifType of
docsCableUpstreamChannel (205)."
INDEX { ifIndex }
::= { docsIfSignalQualityTable 1 }
DocsIfSignalQualityEntry ::= SEQUENCE {
docsIfSigQIncludesContention TruthValue,
docsIfSigQUnerroreds Counter32,
docsIfSigQCorrecteds Counter32,
docsIfSigQUncorrectables Counter32,
docsIfSigQSignalNoise TenthdB,
docsIfSigQMicroreflections Integer32,
Raftus Expires March 2004 [Page 39]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfSigQEqualizationData OCTET STRING,
docsIfSigQExtUnerroreds Counter64,
docsIfSigQExtCorrecteds Counter64,
docsIfSigQExtUncorrectables Counter64
}
docsIfSigQIncludesContention OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"true(1) if this CMTS includes contention intervals in
the counters in this table. Always false(2) for CMs."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4.1"
::= { docsIfSignalQualityEntry 1 }
docsIfSigQUnerroreds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel without error.
This includes all codewords, whether or not they
were part of frames destined for this device.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfSignalQualityEntry 2 }
docsIfSigQCorrecteds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel with correctable
errors. This includes all codewords, whether or not
they were part of frames destined for this device.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Raftus Expires March 2004 [Page 40]
Internet Draft DOCSIS RF Interface MIB September 2003
Section 6.2.5."
::= { docsIfSignalQualityEntry 3 }
docsIfSigQUncorrectables OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel with uncorrectable
errors. This includes all codewords, whether or not
they were part of frames destined for this device.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfSignalQualityEntry 4 }
docsIfSigQSignalNoise OBJECT-TYPE
SYNTAX TenthdB
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Signal/Noise ratio as perceived for this channel.
At the CM, describes the Signal/Noise of the downstream
channel. At the CMTS, describes the average Signal/Noise
of the upstream channel."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Tables 4-1 and 4-2"
::= { docsIfSignalQualityEntry 5 }
docsIfSigQMicroreflections OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "dBc"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total microreflections including in-channel response
as perceived on this interface, measured in dBc below
the signal level.
This object is not assumed to return an absolutely
accurate value, but should give a rough indication
of microreflections received on this interface.
It is up to the implementer to provide information
as accurate as possible.
Discontinuities in the value of this counter can occur
Raftus Expires March 2004 [Page 41]
Internet Draft DOCSIS RF Interface MIB September 2003
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Tables 4-1 and 4-2"
::= { docsIfSignalQualityEntry 6 }
docsIfSigQEqualizationData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CM, returns the equalization data for the
downstream channel. At the CMTS, returns the average
equalization data for the upstream channel. Returns an
empty string if the value is unknown or if there is no
equalization data available or defined."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.3.2."
::= { docsIfSignalQualityEntry 7 }
docsIfSigQExtUnerroreds OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel without error.
This includes all codewords, whether or not they
were part of frames destined for this device.
This is the 64 bit version of docsIfSigQUnerroreds.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfSignalQualityEntry 8 }
docsIfSigQExtCorrecteds OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel with correctable
errors. This includes all codewords, whether or not
they were part of frames destined for this device.
Raftus Expires March 2004 [Page 42]
Internet Draft DOCSIS RF Interface MIB September 2003
This is the 64 bit version of docsIfSigQCorrecteds.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfSignalQualityEntry 9 }
docsIfSigQExtUncorrectables OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received on this channel with uncorrectable
errors. This includes all codewords, whether or not
they were part of frames destined for this device.
This is the 64 bit version of docsIfSigQUncorrectables.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfSignalQualityEntry 10 }
--
-- DOCSIS Version of the device
--
docsIfDocsisBaseCapability OBJECT-TYPE
SYNTAX DocsisVersion
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indication of the DOCSIS capability of the device.
This object mirrors docsIfDocsisCapability from the
DocsIfExt mib."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Annex G."
::= { docsIfBaseObjects 5 }
--
-- CABLE MODEM GROUP
Raftus Expires March 2004 [Page 43]
Internet Draft DOCSIS RF Interface MIB September 2003
--
-- #######
--
-- The CM MAC Table
--
docsIfCmMacTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of each CM MAC interface,
extending the information available from ifEntry."
::= { docsIfCmObjects 1 }
docsIfCmMacEntry OBJECT-TYPE
SYNTAX DocsIfCmMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing objects describing attributes of
each MAC entry, extending the information in ifEntry.
An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsIfCmMacTable 1 }
DocsIfCmMacEntry ::= SEQUENCE {
docsIfCmCmtsAddress MacAddress,
docsIfCmCapabilities BITS,
docsIfCmRangingRespTimeout TimeTicks,
docsIfCmRangingTimeout TimeInterval
}
docsIfCmCmtsAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the CMTS that is believed to control this MAC
domain. At the CM, this will be the source address from
SYNC, MAP, and other MAC-layer messages. If the CMTS is
unknown, returns 00-00-00-00-00-00."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.2.2."
::= { docsIfCmMacEntry 1 }
Raftus Expires March 2004 [Page 44]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmCapabilities OBJECT-TYPE
SYNTAX BITS {
atmCells(0),
concatenation(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the capabilities of the MAC implementation
at this interface. Note that packet transmission is
always supported. Therefore, there is no specific bit
required to explicitly indicate this capability.
Note that BITS objects are encoded most significant bit
first. For example, if bit 1 is set, the value of this
object is the octet string '40'H."
::= { docsIfCmMacEntry 2 }
-- This object has been obsoleted and replaced by
-- docsIfCmRangingTimeout to correct the typing to TimeInterval. New
-- implementations of the MIB should use docsIfCmRangingTimeout
-- instead.
docsIfCmRangingRespTimeout OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-write
STATUS obsolete
DESCRIPTION
"Waiting time for a Ranging Response packet."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.1.6."
DEFVAL { 20 }
::= { docsIfCmMacEntry 3 }
docsIfCmRangingTimeout OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Waiting time for a Ranging Response packet."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.1.6, timer T3."
DEFVAL { 20 }
::= { docsIfCmMacEntry 4 }
--
-- CM status table.
-- This table is implemented only at the CM.
Raftus Expires March 2004 [Page 45]
Internet Draft DOCSIS RF Interface MIB September 2003
--
docsIfCmStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table maintains a number of status objects
and counters for Cable Modems."
::= { docsIfCmObjects 2 }
docsIfCmStatusEntry OBJECT-TYPE
SYNTAX DocsIfCmStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of status objects and counters for a single MAC
layer instance in a Cable Modem.
An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsIfCmStatusTable 1 }
DocsIfCmStatusEntry ::= SEQUENCE {
docsIfCmStatusValue INTEGER,
docsIfCmStatusCode OCTET STRING,
docsIfCmStatusTxPower TenthdBmV,
docsIfCmStatusResets Counter32,
docsIfCmStatusLostSyncs Counter32,
docsIfCmStatusInvalidMaps Counter32,
docsIfCmStatusInvalidUcds Counter32,
docsIfCmStatusInvalidRangingResponses Counter32,
docsIfCmStatusInvalidRegistrationResponses Counter32,
docsIfCmStatusT1Timeouts Counter32,
docsIfCmStatusT2Timeouts Counter32,
docsIfCmStatusT3Timeouts Counter32,
docsIfCmStatusT4Timeouts Counter32,
docsIfCmStatusRangingAborteds Counter32,
docsIfCmStatusDocsisOperMode DocsisQosVersion,
docsIfCmStatusModulationType DocsisUpstreamTypeStatus,
docsIfCmStatusEqualizationData OCTET STRING,
docsIfCmStatusUCCs Counter32,
docsIfCmStatusUCCFails Counter32
}
docsIfCmStatusValue OBJECT-TYPE
SYNTAX INTEGER {
other(1),
notReady(2),
notSynchronized(3),
phySynchronized(4),
Raftus Expires March 2004 [Page 46]
Internet Draft DOCSIS RF Interface MIB September 2003
usParametersAcquired(5),
rangingComplete(6),
ipComplete(7),
todEstablished(8),
securityEstablished(9),
paramTransferComplete(10),
registrationComplete(11),
operational(12),
accessDenied(13)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current Cable Modem connectivity state, as specified
in the RF Interface Specification. Interpretations for
state values 1-12 are clearly outlined in the SP-RFI
reference given below.
As stated in the description for object
docsIfCmtsCmStatusValue, accessDenied(13)indicates the
CMTS has sent a Registration Aborted message to the CM."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 11.2.
Data-Over-Cable Service Interface Specifications:
Operations Support System Interface Specification
SP-OSSIv2.0-IO4-030730, Section 6.3.4.2."
::= { docsIfCmStatusEntry 1 }
docsIfCmStatusCode OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Status code for this Cable Modem as defined in the
OSSI Specification. The status code consists
of a single character indicating error groups, followed
by a two- or three-digit number indicating the status
condition, followed by a decimal."
REFERENCE
"Data-Over-Cable Service Interface Specifications:
Operations Support System Interface Specification
SP-OSSIv2.0-I04-030730, Annex D."
::= { docsIfCmStatusEntry 2 }
docsIfCmStatusTxPower OBJECT-TYPE
SYNTAX TenthdBmV
UNITS "dBmV"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational transmit power for the attached upstream
Raftus Expires March 2004 [Page 47]
Internet Draft DOCSIS RF Interface MIB September 2003
channel."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.18."
::= { docsIfCmStatusEntry 3 }
docsIfCmStatusResets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM reset or initialized this
interface."
::= { docsIfCmStatusEntry 4 }
docsIfCmStatusLostSyncs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM lost synchronization with
the downstream channel.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.2."
::= { docsIfCmStatusEntry 5 }
docsIfCmStatusInvalidMaps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM received invalid MAP messages.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.4."
::= { docsIfCmStatusEntry 6 }
docsIfCmStatusInvalidUcds OBJECT-TYPE
SYNTAX Counter32
Raftus Expires March 2004 [Page 48]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM received invalid UCD messages.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.3."
::= { docsIfCmStatusEntry 7 }
docsIfCmStatusInvalidRangingResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM received invalid ranging response
messages.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.6."
::= { docsIfCmStatusEntry 8 }
docsIfCmStatusInvalidRegistrationResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the CM received invalid registration
response messages.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.8."
::= { docsIfCmStatusEntry 9 }
docsIfCmStatusT1Timeouts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Raftus Expires March 2004 [Page 49]
Internet Draft DOCSIS RF Interface MIB September 2003
DESCRIPTION
"Number of times counter T1 expired in the CM.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 9-2."
::= { docsIfCmStatusEntry 10 }
docsIfCmStatusT2Timeouts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times counter T2 expired in the CM.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 9-2."
::= { docsIfCmStatusEntry 11 }
docsIfCmStatusT3Timeouts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times counter T3 expired in the CM.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 9-2."
::= { docsIfCmStatusEntry 12 }
docsIfCmStatusT4Timeouts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times counter T4 expired in the CM.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
Raftus Expires March 2004 [Page 50]
Internet Draft DOCSIS RF Interface MIB September 2003
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 9-2."
::= { docsIfCmStatusEntry 13 }
docsIfCmStatusRangingAborteds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the ranging process was aborted
by the CMTS.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.3.3."
::= { docsIfCmStatusEntry 14 }
docsIfCmStatusDocsisOperMode OBJECT-TYPE
SYNTAX DocsisQosVersion
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indication whether the device has registered using 1.0
Class of Service or 1.1 Quality of Service.
An unregistered CM should indicate 1.1 QOS for a
docsIfDocsisBaseCapability value of Docsis 1.1/2.0. An
unregistered CM should indicate 1.0 COS for a
docsIfDocsisBaseCapability value of Docsis 1.0.
This object mirrors docsIfCmDocsisOperMode from the
docsIfExt mib."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Annex G."
::= { docsIfCmStatusEntry 15 }
docsIfCmStatusModulationType OBJECT-TYPE
SYNTAX DocsisUpstreamTypeStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates modulation type status currently used by the
CM. Since this object specifically identifies PHY mode,
the shared upstream channel type is not permitted."
Raftus Expires March 2004 [Page 51]
Internet Draft DOCSIS RF Interface MIB September 2003
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.1."
::= { docsIfCmStatusEntry 16 }
docsIfCmStatusEqualizationData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Pre-equalization data for this CM after convolution with
data indicated in the RNG-RSP. This data is valid when
docsIfUpChannelPreEqEnable is set to true. The
value should be formatted as defined in the following
REFERENCE, beginning with the main tap location field.
The type and length fields shown in the referenced figure
must not be included.
Returns an empty string if the value is unknown or if
there is no equalization data available or defined."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 8-23."
::= { docsIfCmStatusEntry 17 }
docsIfCmStatusUCCs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of successful Upstream Channel Change
transactions.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmStatusEntry 18 }
docsIfCmStatusUCCFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of failed Upstream Channel Change
transactions.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
Raftus Expires March 2004 [Page 52]
Internet Draft DOCSIS RF Interface MIB September 2003
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmStatusEntry 19 }
--
-- The Cable Modem Service Table
--
docsIfCmServiceTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmServiceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of each upstream service queue
on a CM."
::= { docsIfCmObjects 3 }
docsIfCmServiceEntry OBJECT-TYPE
SYNTAX DocsIfCmServiceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of an upstream bandwidth service
queue.
An entry in this table exists for each Service ID.
The primary index is an ifIndex with an ifType of
docsCableMaclayer(127)."
INDEX { ifIndex, docsIfCmServiceId }
::= { docsIfCmServiceTable 1 }
DocsIfCmServiceEntry ::= SEQUENCE {
docsIfCmServiceId Integer32,
docsIfCmServiceQosProfile Integer32,
docsIfCmServiceTxSlotsImmed Counter32,
docsIfCmServiceTxSlotsDed Counter32,
docsIfCmServiceTxRetries Counter32,
docsIfCmServiceTxExceededs Counter32,
docsIfCmServiceRqRetries Counter32,
docsIfCmServiceRqExceededs Counter32,
docsIfCmServiceExtTxSlotsImmed Counter64,
docsIfCmServiceExtTxSlotsDed Counter64
}
docsIfCmServiceId OBJECT-TYPE
SYNTAX Integer32 (1..16383)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies a service queue for upstream bandwidth. The
attributes of this service queue are shared between the
Raftus Expires March 2004 [Page 53]
Internet Draft DOCSIS RF Interface MIB September 2003
CM and the CMTS. The CMTS allocates upstream bandwidth
to this service queue based on requests from the CM and
on the class of service associated with this queue."
::= { docsIfCmServiceEntry 1 }
docsIfCmServiceQosProfile OBJECT-TYPE
SYNTAX Integer32 (0..16383)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index in docsIfQosProfileTable describing the quality
of service attributes associated with this particular
service. If no associated entry in docsIfQosProfileTable
exists, this object returns a value of zero."
::= { docsIfCmServiceEntry 2 }
docsIfCmServiceTxSlotsImmed OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of upstream mini-slots which have been used to
transmit data PDUs in immediate (contention) mode. This
includes only those PDUs that are presumed to have
arrived at the headend (i.e., those which were explicitly
acknowledged.) It does not include retransmission attempts
or mini-slots used by Requests.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 3 }
docsIfCmServiceTxSlotsDed OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of upstream mini-slots which have been used to
transmit data PDUs in dedicated mode (i.e., as a result
of a unicast Data Grant).
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Raftus Expires March 2004 [Page 54]
Internet Draft DOCSIS RF Interface MIB September 2003
Section 9.4."
::= { docsIfCmServiceEntry 4 }
docsIfCmServiceTxRetries OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of attempts to transmit data PDUs containing
requests for acknowledgment that did not result in
acknowledgment.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 5 }
docsIfCmServiceTxExceededs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of data PDUs transmission failures due to
excessive retries without acknowledgment.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 6 }
docsIfCmServiceRqRetries OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of attempts to transmit bandwidth requests
which did not result in acknowledgment.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Raftus Expires March 2004 [Page 55]
Internet Draft DOCSIS RF Interface MIB September 2003
Section 9.4."
::= { docsIfCmServiceEntry 7 }
docsIfCmServiceRqExceededs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests for bandwidth which failed due to
excessive retries without acknowledgment.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 8 }
docsIfCmServiceExtTxSlotsImmed OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of upstream mini-slots which have been used to
transmit data PDUs in immediate (contention) mode. This
includes only those PDUs that are presumed to have
arrived at the headend (i.e., those which were explicitly
acknowledged.) It does not include retransmission attempts
or mini-slots used by Requests.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 9 }
docsIfCmServiceExtTxSlotsDed OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of upstream mini-slots which have been used to
transmit data PDUs in dedicated mode (i.e., as a result
of a unicast Data Grant).
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
Raftus Expires March 2004 [Page 56]
Internet Draft DOCSIS RF Interface MIB September 2003
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.4."
::= { docsIfCmServiceEntry 10 }
--
-- CMTS GROUP
--
--
-- The CMTS MAC Table
--
docsIfCmtsMacTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of each CMTS MAC interface,
extending the information available from ifEntry.
Mandatory for all CMTS devices."
::= { docsIfCmtsObjects 1 }
docsIfCmtsMacEntry OBJECT-TYPE
SYNTAX DocsIfCmtsMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing objects describing attributes of each
MAC entry, extending the information in ifEntry.
An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsIfCmtsMacTable 1 }
DocsIfCmtsMacEntry ::= SEQUENCE {
docsIfCmtsCapabilities BITS,
docsIfCmtsSyncInterval Integer32,
docsIfCmtsUcdInterval Integer32,
docsIfCmtsMaxServiceIds Integer32,
docsIfCmtsInsertionInterval TimeTicks, -- Obsolete
docsIfCmtsInvitedRangingAttempts Integer32,
docsIfCmtsInsertInterval TimeInterval
}
docsIfCmtsCapabilities OBJECT-TYPE
Raftus Expires March 2004 [Page 57]
Internet Draft DOCSIS RF Interface MIB September 2003
SYNTAX BITS {
atmCells(0),
concatenation(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the capabilities of the CMTS MAC
implementation at this interface. Note that packet
transmission is always supported. Therefore, there
is no specific bit required to explicitly indicate
this capability.
Note that BITS objects are encoded most significant bit
first. For example, if bit 1 is set, the value of this
object is the octet string '40'H."
::= { docsIfCmtsMacEntry 1 }
docsIfCmtsSyncInterval OBJECT-TYPE
SYNTAX Integer32 (1..200)
UNITS "Milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval between CMTS transmission of successive SYNC
messages at this interface."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.3."
::= { docsIfCmtsMacEntry 2 }
docsIfCmtsUcdInterval OBJECT-TYPE
SYNTAX Integer32 (1..2000)
UNITS "Milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval between CMTS transmission of successive
Upstream Channel Descriptor messages for each upstream
channel at this interface."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.3"
::= { docsIfCmtsMacEntry 3 }
docsIfCmtsMaxServiceIds OBJECT-TYPE
SYNTAX Integer32 (1..16383)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of service IDs that may be
Raftus Expires March 2004 [Page 58]
Internet Draft DOCSIS RF Interface MIB September 2003
simultaneously active."
::= { docsIfCmtsMacEntry 4 }
-- This object has been obsoleted and replaced by
-- docsIfCmtsInsertInterval to fix a SYNTAX typing problem. New
-- implementations of this MIB should use that object instead.
docsIfCmtsInsertionInterval OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-write
STATUS obsolete
DESCRIPTION
"The amount of time to elapse between each broadcast
initial maintenance grant. Broadcast initial maintenance
grants are used to allow new cable modems to join the
network. Zero indicates that a vendor-specific algorithm
is used instead of a fixed time. Maximum amount of time
permitted by the specification is 2 seconds."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Annex B."
::= { docsIfCmtsMacEntry 5 }
docsIfCmtsInvitedRangingAttempts OBJECT-TYPE
SYNTAX Integer32 (0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of attempts to make on invitations
for ranging requests. A value of zero means the system
should attempt to range forever."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 9.3.3 and Annex B."
::= { docsIfCmtsMacEntry 6 }
docsIfCmtsInsertInterval OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The amount of time to elapse between each broadcast
initial maintenance grant. Broadcast initial maintenance
grants are used to allow new cable modems to join the
network. Zero indicates that a vendor-specific algorithm
is used instead of a fixed time. Maximum amount of time
permitted by the specification is 2 seconds."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Annex B."
Raftus Expires March 2004 [Page 59]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfCmtsMacEntry 7 }
--
--
-- CMTS status table.
--
docsIfCmtsStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"For the MAC layer, this group maintains a number of
status objects and counters."
::= { docsIfCmtsObjects 2 }
docsIfCmtsStatusEntry OBJECT-TYPE
SYNTAX DocsIfCmtsStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Status entry for a single MAC layer.
An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsIfCmtsStatusTable 1 }
DocsIfCmtsStatusEntry ::= SEQUENCE {
docsIfCmtsStatusInvalidRangeReqs Counter32,
docsIfCmtsStatusRangingAborteds Counter32,
docsIfCmtsStatusInvalidRegReqs Counter32,
docsIfCmtsStatusFailedRegReqs Counter32,
docsIfCmtsStatusInvalidDataReqs Counter32,
docsIfCmtsStatusT5Timeouts Counter32
}
docsIfCmtsStatusInvalidRangeReqs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts invalid RNG-REQ messages received on
this interface.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.5."
Raftus Expires March 2004 [Page 60]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfCmtsStatusEntry 1 }
docsIfCmtsStatusRangingAborteds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts ranging attempts that were explicitly
aborted by the CMTS.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.6."
::= { docsIfCmtsStatusEntry 2 }
docsIfCmtsStatusInvalidRegReqs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts invalid REG-REQ messages received on
this interface. That is, syntax, out of range parameters,
or erroneous requests.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.7."
::= { docsIfCmtsStatusEntry 3 }
docsIfCmtsStatusFailedRegReqs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts failed registration attempts. Included
are docsIfCmtsStatusInvalidRegReqs, authentication and
class of service failures.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Raftus Expires March 2004 [Page 61]
Internet Draft DOCSIS RF Interface MIB September 2003
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.3.7."
::= { docsIfCmtsStatusEntry 4 }
docsIfCmtsStatusInvalidDataReqs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts invalid data request messages
received on this interface.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsStatusEntry 5 }
docsIfCmtsStatusT5Timeouts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times counter T5
expired on this interface.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 9-2."
::= { docsIfCmtsStatusEntry 6 }
--
-- CM status table (within CMTS).
-- This table is implemented only at the CMTS.
-- It contains per CM status information available in the CMTS.
--
docsIfCmtsCmStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsCmStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects in the CMTS, maintained for each
Cable Modem connected to this CMTS."
::= { docsIfCmtsObjects 3 }
docsIfCmtsCmStatusEntry OBJECT-TYPE
SYNTAX DocsIfCmtsCmStatusEntry
Raftus Expires March 2004 [Page 62]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Status information for a single Cable Modem.
An entry in this table exists for each Cable Modem
that is connected to the CMTS implementing this table."
INDEX { docsIfCmtsCmStatusIndex }
::= { docsIfCmtsCmStatusTable 1 }
DocsIfCmtsCmStatusEntry ::= SEQUENCE {
docsIfCmtsCmStatusIndex Integer32,
docsIfCmtsCmStatusMacAddress MacAddress,
docsIfCmtsCmStatusIpAddress IpAddress, -- Deprecated
docsIfCmtsCmStatusDownChannelIfIndex InterfaceIndexOrZero,
docsIfCmtsCmStatusUpChannelIfIndex InterfaceIndexOrZero,
docsIfCmtsCmStatusRxPower TenthdBmV,
docsIfCmtsCmStatusTimingOffset Unsigned32,
docsIfCmtsCmStatusEqualizationData OCTET STRING,
docsIfCmtsCmStatusValue INTEGER,
docsIfCmtsCmStatusUnerroreds Counter32,
docsIfCmtsCmStatusCorrecteds Counter32,
docsIfCmtsCmStatusUncorrectables Counter32,
docsIfCmtsCmStatusSignalNoise TenthdB,
docsIfCmtsCmStatusMicroreflections Integer32,
docsIfCmtsCmStatusExtUnerroreds Counter64,
docsIfCmtsCmStatusExtCorrecteds Counter64,
docsIfCmtsCmStatusExtUncorrectables Counter64,
docsIfCmtsCmStatusDocsisRegMode DocsisQosVersion,
docsIfCmtsCmStatusModulationType DocsisUpstreamTypeStatus,
docsIfCmtsCmStatusInetAddressType InetAddressType,
docsIfCmtsCmStatusInetAddress InetAddress,
docsIfCmtsCmStatusValueLastUpdate TimeStamp,
docsIfCmtsCmStatusHighResolutionTimingOffset Unsigned32
}
docsIfCmtsCmStatusIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index value to uniquely identify an entry in this table.
For an individual Cable Modem, this index value should
not change during CMTS uptime."
::= { docsIfCmtsCmStatusEntry 1 }
docsIfCmtsCmStatusMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"MAC address of this Cable Modem. If the Cable Modem has
multiple MAC addresses, this is the MAC address associated
Raftus Expires March 2004 [Page 63]
Internet Draft DOCSIS RF Interface MIB September 2003
with the Cable interface."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 8.2.2."
::= { docsIfCmtsCmStatusEntry 2 }
docsIfCmtsCmStatusIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"IP address of this Cable Modem. If the Cable Modem has no
IP address assigned, or the IP address is unknown, this
object returns a value of 0.0.0.0. If the Cable Modem has
multiple IP addresses, this object returns the IP address
associated with the Cable interface.
This object has been deprecated and replaced by
docsIfCmtsCmStatusInetAddressType and
docsIfCmtsCmStatusInetAddress, to enable IPv6 addressing
in the future."
::= { docsIfCmtsCmStatusEntry 3 }
docsIfCmtsCmStatusDownChannelIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IfIndex of the downstream channel this CM is connected
to. If the downstream channel is unknown, this object
returns a value of zero."
::= { docsIfCmtsCmStatusEntry 4 }
docsIfCmtsCmStatusUpChannelIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IfIndex of the upstream channel this CM is connected
to. If the upstream channel is unknown, this object
returns a value of zero."
::= { docsIfCmtsCmStatusEntry 5 }
docsIfCmtsCmStatusRxPower OBJECT-TYPE
SYNTAX TenthdBmV
UNITS "dBmV"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The receive power as perceived for upstream data from
this Cable Modem.
If the receive power is unknown, this object returns
Raftus Expires March 2004 [Page 64]
Internet Draft DOCSIS RF Interface MIB September 2003
a value of zero."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 6-11."
::= { docsIfCmtsCmStatusEntry 6 }
docsIfCmtsCmStatusTimingOffset OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A measure of the current round trip time for this CM.
Used for timing of CM upstream transmissions to ensure
synchronized arrivals at the CMTS. Units are in terms
of (6.25 microseconds/64). Returns zero if the value
is unknown.
For channels requiring finer resolution, please refer to
object docsIfCmtsCmStatusHighResolutionTimingOffset."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.17."
::= { docsIfCmtsCmStatusEntry 7 }
docsIfCmtsCmStatusEqualizationData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equalization data for this CM. Returns an empty string
if the value is unknown or if there is no equalization
data available or defined."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Figure 8-23."
::= { docsIfCmtsCmStatusEntry 8 }
docsIfCmtsCmStatusValue OBJECT-TYPE
SYNTAX INTEGER {
other(1),
ranging(2),
rangingAborted(3),
rangingComplete(4),
ipComplete(5),
registrationComplete(6),
accessDenied(7),
operational(8), -- deprecated
registeredBPIInitializing(9)
}
MAX-ACCESS read-only
Raftus Expires March 2004 [Page 65]
Internet Draft DOCSIS RF Interface MIB September 2003
STATUS current
DESCRIPTION
"Current Cable Modem connectivity state, as specified
in the RF Interface Specification. Returned status
information is the CM status as assumed by the CMTS,
and indicates the following events:
other(1)
Any state other than below.
ranging(2)
The CMTS has received an Initial Ranging Request
message from the CM, and the ranging process is not
yet complete.
rangingAborted(3)
The CMTS has sent a Ranging Abort message to the CM.
rangingComplete(4)
The CMTS has sent a Ranging Complete message to the CM.
ipComplete(5)
The CMTS has received a DHCP reply message and
forwarded it to the CM.
registrationComplete(6)
The CMTS has sent a Registration Response message to
the CM.
accessDenied(7)
The CMTS has sent a Registration Aborted message
to the CM.
operational(8) -- deprecated value
This value has been deprecated in favor of the more
Specific registeredBPIInitializing(9).
registeredBPIInitializing(9)
Baseline Privacy (BPI) is enabled and the CMTS is in the
process of completing BPI initialization. This state may
last for a significant length of time if failures occur
during the initialization process. After completion of
BPI initialization, the CMTS will report
registrationComplete(6).
The CMTS only needs to report states it is able to
detect."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 11.2."
::= { docsIfCmtsCmStatusEntry 9 }
docsIfCmtsCmStatusUnerroreds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received without error from this Cable Modem.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
Raftus Expires March 2004 [Page 66]
Internet Draft DOCSIS RF Interface MIB September 2003
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 10 }
docsIfCmtsCmStatusCorrecteds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received with correctable errors from this
Cable Modem.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 11 }
docsIfCmtsCmStatusUncorrectables OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received with uncorrectable errors from this
Cable Modem.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 12 }
docsIfCmtsCmStatusSignalNoise OBJECT-TYPE
SYNTAX TenthdB
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Signal/Noise ratio as perceived for upstream data from
this Cable Modem.
If the Signal/Noise is unknown, this object returns
a value of zero."
REFERENCE
Raftus Expires March 2004 [Page 67]
Internet Draft DOCSIS RF Interface MIB September 2003
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Tables 4-1 and 4-2."
::= { docsIfCmtsCmStatusEntry 13 }
docsIfCmtsCmStatusMicroreflections OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "dBc"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total microreflections including in-channel response
as perceived on this interface, measured in dBc below
the signal level.
This object is not assumed to return an absolutely
accurate value, but should give a rough indication
of microreflections received on this interface.
It is up to the implementer to provide information
as accurate as possible.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Tables 4-1 and 4-2"
::= { docsIfCmtsCmStatusEntry 14 }
docsIfCmtsCmStatusExtUnerroreds OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received without error from this Cable Modem.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 15 }
docsIfCmtsCmStatusExtCorrecteds OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received with correctable errors from this
Cable Modem.
Raftus Expires March 2004 [Page 68]
Internet Draft DOCSIS RF Interface MIB September 2003
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 16 }
docsIfCmtsCmStatusExtUncorrectables OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Codewords received with uncorrectable errors from this
Cable Modem.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.5."
::= { docsIfCmtsCmStatusEntry 17 }
docsIfCmtsCmStatusDocsisRegMode OBJECT-TYPE
SYNTAX DocsisQosVersion
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Indication whether the CM has registered using 1.0
Class of Service or 1.1 Quality of Service.
This object mirrors docsIfCmtsCmStatusDocsisMode from
the docsIfExt mib."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Annex G."
::= { docsIfCmtsCmStatusEntry 18 }
docsIfCmtsCmStatusModulationType OBJECT-TYPE
SYNTAX DocsisUpstreamTypeStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates modulation type currently used by the CM. Since
this object specifically identifies PHY mode, the shared
type is not permitted. If the upstream channel is
unknown, this object returns a value of zero."
REFERENCE
Raftus Expires March 2004 [Page 69]
Internet Draft DOCSIS RF Interface MIB September 2003
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
::= { docsIfCmtsCmStatusEntry 19 }
docsIfCmtsCmStatusInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of internet address of
docsIfCmtsCmStatusInetAddress. If the cable modem
Internet address is unassigned or unknown, then the
value of this object is unknown(0)."
::= { docsIfCmtsCmStatusEntry 20 }
docsIfCmtsCmStatusInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Internet address of this Cable Modem. If the Cable
Modem has no Internet address assigned, or the Internet
address is unknown, the value of this object is the
empty string. If the Cable Modem has multiple Internet
addresses, this object returns the Internet address
associated with the Cable (i.e. RF MAC) interface."
::= { docsIfCmtsCmStatusEntry 21 }
docsIfCmtsCmStatusValueLastUpdate OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when docsIfCmtsCmStatusValue
was last updated."
::= { docsIfCmtsCmStatusEntry 22 }
docsIfCmtsCmStatusHighResolutionTimingOffset OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A measure of the current round trip time for this CM.
Used for timing of CM upstream transmissions to ensure
synchronized arrivals at the CMTS. Units are in terms
of (6.25 microseconds/(64*256)). Returns zero if the value
is unknown.
This is the high resolution version of object
docsIfCmtsCmStatusTimingOffset, for channels requiring
finer resolution."
REFERENCE
Raftus Expires March 2004 [Page 70]
Internet Draft DOCSIS RF Interface MIB September 2003
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Section 6.2.17."
::= { docsIfCmtsCmStatusEntry 23 }
--
-- The CMTS Service Table.
--
docsIfCmtsServiceTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsServiceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of upstream service queues
in a Cable Modem Termination System."
::= { docsIfCmtsObjects 4 }
docsIfCmtsServiceEntry OBJECT-TYPE
SYNTAX DocsIfCmtsServiceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes the attributes of a single upstream bandwidth
service queue.
Entries in this table exist for each ifEntry with an
ifType of docsCableMaclayer(127), and for each service
queue (Service ID) within this MAC layer.
Entries in this table are created with the creation of
individual Service IDs by the MAC layer and removed
when a Service ID is removed."
INDEX { ifIndex, docsIfCmtsServiceId }
::= { docsIfCmtsServiceTable 1 }
DocsIfCmtsServiceEntry ::= SEQUENCE {
docsIfCmtsServiceId Integer32,
docsIfCmtsServiceCmStatusIndex Integer32, -- Deprecated
docsIfCmtsServiceAdminStatus INTEGER,
docsIfCmtsServiceQosProfile Integer32,
docsIfCmtsServiceCreateTime TimeStamp,
docsIfCmtsServiceInOctets Counter32,
docsIfCmtsServiceInPackets Counter32,
docsIfCmtsServiceNewCmStatusIndex Integer32
}
docsIfCmtsServiceId OBJECT-TYPE
SYNTAX Integer32 (1..16383)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies a service queue for upstream bandwidth. The
Raftus Expires March 2004 [Page 71]
Internet Draft DOCSIS RF Interface MIB September 2003
attributes of this service queue are shared between the
Cable Modem and the Cable Modem Termination System.
The CMTS allocates upstream bandwidth to this service
queue based on requests from the CM and on the class of
service associated with this queue."
::= { docsIfCmtsServiceEntry 1 }
docsIfCmtsServiceCmStatusIndex OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Pointer to an entry in docsIfCmtsCmStatusTable identifying
the Cable Modem using this Service Queue. If multiple
Cable Modems are using this Service Queue, the value of
this object is zero.
This object has been deprecated and replaced by
docsIfCmtsServiceNewCmStatusIndex, to fix a mismatch
of the value range with respect to docsIfCmtsCmStatusIndex
(1..2147483647)."
::= { docsIfCmtsServiceEntry 2 }
docsIfCmtsServiceAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2),
destroyed(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allows a service class for a particular modem to be
suppressed, (re-)enabled, or deleted altogether."
::= { docsIfCmtsServiceEntry 3 }
docsIfCmtsServiceQosProfile OBJECT-TYPE
SYNTAX Integer32 (0..16383)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index in docsIfQosProfileTable describing the quality
of service attributes associated with this particular
service. If no associated docsIfQosProfileTable entry
exists, this object returns a value of zero."
::= { docsIfCmtsServiceEntry 4 }
docsIfCmtsServiceCreateTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this entry was created."
Raftus Expires March 2004 [Page 72]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfCmtsServiceEntry 5 }
docsIfCmtsServiceInOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The cumulative number of Packet Data octets received
on this Service ID. The count does not include the
size of the Cable MAC header.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsServiceEntry 6 }
docsIfCmtsServiceInPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The cumulative number of Packet Data packets received
on this Service ID.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsServiceEntry 7 }
docsIfCmtsServiceNewCmStatusIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Pointer (via docsIfCmtsCmStatusIndex) to an entry in
docsIfCmtsCmStatusTable identifying the Cable Modem
using this Service Queue. If multiple Cable Modems are
using this Service Queue, the value of this object is
zero."
::= { docsIfCmtsServiceEntry 8 }
--
-- The following table provides upstream channel modulation profiles.
-- Entries in this table can be
-- re-used by one or more upstream channels. An upstream channel will
-- have a modulation profile
-- for each value of docsIfModIntervalUsageCode.
--
docsIfCmtsModulationTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsModulationEntry
Raftus Expires March 2004 [Page 73]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes a modulation profile associated with one or more
upstream channels."
::= { docsIfCmtsObjects 5 }
docsIfCmtsModulationEntry OBJECT-TYPE
SYNTAX DocsIfCmtsModulationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes a modulation profile for an Interval Usage Code
for one or more upstream channels.
Entries in this table are created by the operator. Initial
default entries may be created at system initialization
time. No individual objects have to be specified in order
to create an entry in this table.
Note that some objects do not have DEFVALs, but do have
calculated defaults and need not be specified during row
creation.
There is no restriction on the changing of values in this
table while their associated rows are active."
INDEX { docsIfCmtsModIndex, docsIfCmtsModIntervalUsageCode}
::= { docsIfCmtsModulationTable 1 }
DocsIfCmtsModulationEntry ::= SEQUENCE {
docsIfCmtsModIndex Integer32,
docsIfCmtsModIntervalUsageCode INTEGER,
docsIfCmtsModControl RowStatus,
docsIfCmtsModType INTEGER,
docsIfCmtsModPreambleLen Integer32,
docsIfCmtsModDifferentialEncoding TruthValue,
docsIfCmtsModFECErrorCorrection Integer32,
docsIfCmtsModFECCodewordLength Integer32,
docsIfCmtsModScramblerSeed Integer32,
docsIfCmtsModMaxBurstSize Integer32,
docsIfCmtsModGuardTimeSize Unsigned32,
docsIfCmtsModLastCodewordShortened TruthValue,
docsIfCmtsModScrambler TruthValue,
docsIfCmtsModByteInterleaverDepth Unsigned32,
docsIfCmtsModByteInterleaverBlockSize Unsigned32,
docsIfCmtsModPreambleType INTEGER,
docsIfCmtsModTcmErrorCorrectionOn TruthValue,
docsIfCmtsModScdmaInterleaverStepSize Unsigned32,
docsIfCmtsModScdmaSpreaderEnable TruthValue,
docsIfCmtsModScdmaSubframeCodes Unsigned32,
docsIfCmtsModChannelType DocsisUpstreamType
}
docsIfCmtsModIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
Raftus Expires March 2004 [Page 74]
Internet Draft DOCSIS RF Interface MIB September 2003
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index into the Channel Modulation table representing
a group of Interval Usage Codes, all associated with the
same channel."
::= { docsIfCmtsModulationEntry 1 }
docsIfCmtsModIntervalUsageCode OBJECT-TYPE
SYNTAX INTEGER {
request(1),
requestData(2),
initialRanging(3),
periodicRanging(4),
shortData(5),
longData(6),
advPhyShortData(9),
advPhyLongData(10),
ugs(11)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index into the Channel Modulation table which, when
grouped with other Interval Usage Codes, fully
instantiate all modulation sets for a given upstream
channel."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-20."
::= { docsIfCmtsModulationEntry 2 }
docsIfCmtsModControl OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Controls and reflects the status of rows in this table."
::= { docsIfCmtsModulationEntry 3 }
docsIfCmtsModType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
qpsk(2),
qam16(3),
qam8(4),
qam32(5),
qam64(6),
qam128(7)
}
MAX-ACCESS read-create
Raftus Expires March 2004 [Page 75]
Internet Draft DOCSIS RF Interface MIB September 2003
STATUS current
DESCRIPTION
"The modulation type used on this channel. Returns
other(1) if the modulation type is neither
qpsk, qam16, qam8, qam32, qam64 or qam128.
Type qam128 is used for SCDMA channels only.
See the reference for the modulation profiles
implied by different modulation types."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { qpsk }
::= { docsIfCmtsModulationEntry 4 }
docsIfCmtsModPreambleLen OBJECT-TYPE
SYNTAX Integer32 (0..1536)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preamble length for this modulation profile in bits.
Default value is the minimum needed by the implementation
at the CMTS for the given modulation profile."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
::= { docsIfCmtsModulationEntry 5 }
docsIfCmtsModDifferentialEncoding OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies whether or not differential encoding is used
on this channel."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { false }
::= { docsIfCmtsModulationEntry 6 }
docsIfCmtsModFECErrorCorrection OBJECT-TYPE
SYNTAX Integer32 (0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of correctable errored bytes (t) used in
forward error correction code. The value of 0 indicates
no correction is employed. The number of check bytes
appended will be twice this value."
Raftus Expires March 2004 [Page 76]
Internet Draft DOCSIS RF Interface MIB September 2003
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 0 }
::= { docsIfCmtsModulationEntry 7 }
docsIfCmtsModFECCodewordLength OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of data bytes (k) in the forward error
correction codeword.
This object is not used if docsIfCmtsModFECErrorCorrection
is zero."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 32 }
::= { docsIfCmtsModulationEntry 8 }
docsIfCmtsModScramblerSeed OBJECT-TYPE
SYNTAX Integer32 (0..32767)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The 15 bit seed value for the scrambler polynomial."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 0 }
::= { docsIfCmtsModulationEntry 9 }
docsIfCmtsModMaxBurstSize OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of mini-slots that can be transmitted
during this channel's burst time. Returns zero if the
burst length is bounded by the allocation MAP rather than
this profile.
Default value is 0 except for shortData, where it is 8."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
::= { docsIfCmtsModulationEntry 10 }
Raftus Expires March 2004 [Page 77]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsModGuardTimeSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbol-times which must follow the end of
this channel's burst. Default value is the minimum time
needed by the implementation for this modulation profile."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
::= { docsIfCmtsModulationEntry 11 }
docsIfCmtsModLastCodewordShortened OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates if the last FEC codeword is truncated."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { true }
::= { docsIfCmtsModulationEntry 12 }
docsIfCmtsModScrambler OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates if the scrambler is employed."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { false }
::= { docsIfCmtsModulationEntry 13 }
docsIfCmtsModByteInterleaverDepth OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ATDMA Byte Interleaver Depth (Ir). This object returns 1
for non ATDMA profiles."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 1 }
Raftus Expires March 2004 [Page 78]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfCmtsModulationEntry 14 }
docsIfCmtsModByteInterleaverBlockSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ATDMA Byte Interleaver Block size (Br). This object
returns zero for non ATDMA profiles "
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 18 }
::= { docsIfCmtsModulationEntry 15 }
docsIfCmtsModPreambleType OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
qpsk0(1),
qpsk1(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Preamble type for DOCSIS 2.0 bursts. The value
'unknown(0)' represents a row entry consisting only of
DOCSIS 1.x bursts"
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { qpsk0 }
::= { docsIfCmtsModulationEntry 16 }
docsIfCmtsModTcmErrorCorrectionOn OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Trellis Code Modulation (TCM) On/Off. This value returns
false for non S-CDMA profiles."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { false }
::= { docsIfCmtsModulationEntry 17 }
docsIfCmtsModScdmaInterleaverStepSize OBJECT-TYPE
SYNTAX Unsigned32 (0 | 1..32)
MAX-ACCESS read-create
Raftus Expires March 2004 [Page 79]
Internet Draft DOCSIS RF Interface MIB September 2003
STATUS current
DESCRIPTION
" S-CDMA Interleaver step size. This value returns zero
for non S-CDMA profiles."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 1 }
::= { docsIfCmtsModulationEntry 18 }
docsIfCmtsModScdmaSpreaderEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" S-CDMA spreader. This value returns false for non S-CDMA
profiles. Default value for IUC 3 and 4 is OFF, for
all other IUCs it is ON."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
::= { docsIfCmtsModulationEntry 19 }
docsIfCmtsModScdmaSubframeCodes OBJECT-TYPE
SYNTAX Unsigned32 (0 | 1..128)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" S-CDMA sub-frame size. This value returns zero
for non S-CDMA profiles."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { 1 }
::= { docsIfCmtsModulationEntry 20 }
docsIfCmtsModChannelType OBJECT-TYPE
SYNTAX DocsisUpstreamType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Describes the modulation channel type for this modulation
entry."
REFERENCE
"Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730,
Table 8-19."
DEFVAL { tdma }
Raftus Expires March 2004 [Page 80]
Internet Draft DOCSIS RF Interface MIB September 2003
::= { docsIfCmtsModulationEntry 21 }
docsIfCmtsQosProfilePermissions OBJECT-TYPE
SYNTAX BITS {
createByManagement(0),
updateByManagement(1),
createByModems(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies permitted methods of creating
entries in docsIfQosProfileTable.
CreateByManagement(0) is set if entries can be created
using SNMP. UpdateByManagement(1) is set if updating
entries using SNMP is permitted. CreateByModems(2)
is set if entries can be created based on information
in REG-REQ MAC messages received from Cable Modems.
Information in this object is only applicable if
docsIfQosProfileTable is implemented as read-create.
Otherwise, this object is implemented as read-only
and returns CreateByModems(2).
Either CreateByManagement(0) or CreateByModems(1)
must be set when writing to this object.
Note that BITS objects are encoded most significant bit
first. For example, if bit 2 is set, the value of this
object is the octet string '20'H."
::= { docsIfCmtsObjects 6 }
docsIfCmtsMacToCmTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsMacToCmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is a table to provide a quick access index into the
docsIfCmtsCmStatusTable. There is exactly one row in this
table for each row in the docsIfCmtsCmStatusTable. In
general, the management station should use this table only
to get a pointer into the docsIfCmtsCmStatusTable (which
corresponds to the CM's RF interface MAC address), and
should not iterate (e.g. GetNext through) this table."
::= { docsIfCmtsObjects 7 }
docsIfCmtsMacToCmEntry OBJECT-TYPE
SYNTAX DocsIfCmtsMacToCmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the docsIfCmtsMacToCmTable.
An entry in this table exists for each Cable Modem
that is connected to the CMTS implementing this table."
INDEX { docsIfCmtsCmMac }
Raftus Expires March 2004 [Page 81]
Internet Draft DOCSIS RF Interface MIB September 2003
::= {docsIfCmtsMacToCmTable 1 }
DocsIfCmtsMacToCmEntry ::= SEQUENCE {
docsIfCmtsCmMac MacAddress,
docsIfCmtsCmPtr Integer32
}
docsIfCmtsCmMac OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The RF side MAC address for the referenced CM. (E.g. the
interface on the CM that has docsCableMacLayer(127) as
its ifType."
::= { docsIfCmtsMacToCmEntry 1 }
docsIfCmtsCmPtr OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An row index into docsIfCmtsCmStatusTable. When queried
with the correct instance value (e.g. a CM's MAC address),
returns the index in docsIfCmtsCmStatusTable which
represents that CM."
::= { docsIfCmtsMacToCmEntry 2 }
-- The following independent object and associated table provide
-- operators with a mechanism to evaluate the load/utilization of
-- both upstream and downstream physical channels. This information
-- may be used for capacity planning and incident analysis, and may
-- be particularly helpful in provisioning of high value QOS.
--
-- Utilization is expressed as an index representing the calculated
-- percentage utilization of the upstream or downstream channel in
-- the most recent sampling interval (ie. utilization interval).
-- Refer to the DESCRIPTION field of the docsIfCmtsChannelUtUtilization
-- object for definitions and calculation details.
docsIfCmtsChannelUtilizationInterval OBJECT-TYPE
SYNTAX Integer32 (0..86400)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time interval in seconds over which the channel
utilization index is calculated. All upstream/downstream
channels use the same
docsIfCmtsChannelUtilizationInterval.
Raftus Expires March 2004 [Page 82]
Internet Draft DOCSIS RF Interface MIB September 2003
Setting a value of zero disables utilization reporting.
A channel utilization index is calculated over a fixed
window applying to the most recent
docsIfCmtsChannelUtilizationInterval. It would therefore
be prudent to use a relatively short
docsIfCmtsChannelUtilizationInterval.
It is a vendor decision whether to reset the timer when
docsIfCmtsChannelUtilizationInterval is changed during a
utilization sampling period."
::= { docsIfCmtsObjects 8 }
docsIfCmtsChannelUtilizationTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsChannelUtilizationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Reports utilization statistics for attached upstream and
downstream physical channels."
::= { docsIfCmtsObjects 9 }
docsIfCmtsChannelUtilizationEntry OBJECT-TYPE
SYNTAX DocsIfCmtsChannelUtilizationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Utilization statistics for a single upstream or downstream
physical channel. An entry exists in this table for each
ifEntry with an ifType equal to
docsCableDownstreamInterface (128)
or docsCableUpstreamInterface (129)."
INDEX { ifIndex, docsIfCmtsChannelUtIfType,
docsIfCmtsChannelUtId }
::= { docsIfCmtsChannelUtilizationTable 1 }
DocsIfCmtsChannelUtilizationEntry ::= SEQUENCE {
docsIfCmtsChannelUtIfType IANAifType,
docsIfCmtsChannelUtId Integer32,
docsIfCmtsChannelUtUtilization Integer32
}
docsIfCmtsChannelUtIfType OBJECT-TYPE
SYNTAX IANAifType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The secondary index into this table. Indicates the IANA
interface type associated with this physical channel.
Only docsCableDownstreamInterface (128) and
docsCableUpstreamInterface (129) are valid."
::= { docsIfCmtsChannelUtilizationEntry 1 }
Raftus Expires March 2004 [Page 83]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsChannelUtId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The tertiary index into this table. Indicates the CMTS
identifier for this physical channel."
::= { docsIfCmtsChannelUtilizationEntry 2 }
docsIfCmtsChannelUtUtilization OBJECT-TYPE
SYNTAX Integer32 (0..100)
UNITS "percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The calculated and truncated utilization index for this
physical upstream or downstream channel, accurate as of
the most recent docsIfCmtsChannelUtilizationInterval.
Upstream Channel Utilization Index:
The upstream channel utilization index is expressed as a
percentage of minislots utilized on the physical channel,
regardless of burst type. For an Initial Maintenance
region, the minislots for the complete region are
considered utilized if the CMTS received an upstream
burst within the region from any CM on the physical
channel. For contention REQ and REQ/DATA regions, the
minislots for a transmission opportunity within the
region are considered utilized if the CMTS received an
upstream burst within the opportunity from any CM on the
physical channel. For all other regions, utilized
minislots are those in which the CMTS granted
bandwidth to any unicast SID on the physical channel.
For an upstream interface that has multiple logical
upstream channels enabled, the utilization index is a
weighted sum of utilization indices for the logical
channels. The weight for each utilization index is the
percentage of upstream minislots allocated for the
corresponding logical channel.
Example:
If 75% of bandwidth is allocated to the first logical
channel and 25% to the second, and the utilization
indices for each are 60 and 40 respectively, the
utilization index for the upstream physical channel is
(60 * 0.75) + (40 * 0.25) = 55. This figure
applies to the most recent utilization interval.
Downstream Channel Utilization Index:
The downstream channel utilization index is a percentage
expressing the ratio between bytes used to transmit data
versus the total number of bytes transmitted in the raw
Raftus Expires March 2004 [Page 84]
Internet Draft DOCSIS RF Interface MIB September 2003
bandwidth of the MPEG channel. As with the upstream
utilization index, the calculated value represents
the most recent utilization interval.
Formula:
Downstream utilization index =
(100 * (data bytes / raw bytes))
Definitions:
Data bytes: Number of bytes transmitted as data in the
docsIfCmtsChannelUtilizationInterval.
Identical to docsIfCmtsDownChannelCtrUsed
Bytes measured over the utilization
interval.
Raw bandwidth: Total number of bytes available for
transmitting data, not including bytes
used for headers and other overhead.
Raw bytes: (raw bandwidth *
docsIfCmtsChannelUtilizationInterval).
Identical to docsIfCmtsDownChannelCtrTotal
Bytes measured over the utilization
interval."
::= { docsIfCmtsChannelUtilizationEntry 3 }
-- The following table provides operators with input data appropriate
-- for calculating downstream channel utilization. Operators may use
-- the docsIfCmtsChannelUtilizationTable, or perform their own polling
-- of the docsIfCmtsDownChannelCounterTable objects to characterize
-- their downstream channel usage. The 32 bit counter objects are
-- included to provide backward compatibility with SNMPv1 managers,
-- which cannot access 64 bit counter objects.
docsIfCmtsDownChannelCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsDownChannelCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is implemented at the CMTS to collect
downstream channel statistics for utilization
calculations."
::= { docsIfCmtsObjects 10 }
docsIfCmtsDownChannelCounterEntry OBJECT-TYPE
SYNTAX DocsIfCmtsDownChannelCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry provides a list of traffic counters for a single
downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128)."
Raftus Expires March 2004 [Page 85]
Internet Draft DOCSIS RF Interface MIB September 2003
INDEX { ifIndex }
::= { docsIfCmtsDownChannelCounterTable 1 }
DocsIfCmtsDownChannelCounterEntry ::= SEQUENCE {
docsIfCmtsDownChnlCtrId Integer32,
docsIfCmtsDownChnlCtrTotalBytes Counter32,
docsIfCmtsDownChnlCtrUsedBytes Counter32,
docsIfCmtsDownChnlCtrExtTotalBytes Counter64,
docsIfCmtsDownChnlCtrExtUsedBytes Counter64
}
docsIfCmtsDownChnlCtrId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Cable Modem Termination System (CMTS) identification
of the downstream channel within this particular MAC
interface. If the interface is down, the object returns
the most current value. If the downstream channel ID is
unknown, this object returns a value of 0."
::= { docsIfCmtsDownChannelCounterEntry 1 }
docsIfCmtsDownChnlCtrTotalBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CMTS, the total number of bytes in the Payload
portion of MPEG Packets (ie. not including MPEG header
or pointer_field) transported by this downstream channel
since CMTS initialization. This is the 32 bit version of
docsIfCmtsDownChnlCtrExtTotalBytes, included to provide
back compatibility with SNMPv1 managers.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsDownChannelCounterEntry 2 }
docsIfCmtsDownChnlCtrUsedBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CMTS, the total number of DOCSIS data bytes
transported by this downstream channel since CMTS
initialization. The number of data bytes is defined as the
total number of bytes transported in DOCSIS payloads minus
the number of stuff bytes transported in DOCSIS payloads.
This is the 32 bit version of
docsIfCmtsDownChnlCtrExtUsedBytes, included to provide
Raftus Expires March 2004 [Page 86]
Internet Draft DOCSIS RF Interface MIB September 2003
back compatibility with SNMPv1 managers.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsDownChannelCounterEntry 3 }
docsIfCmtsDownChnlCtrExtTotalBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CMTS, the total number of bytes in the Payload
portion of MPEG Packets (ie. not including MPEG header
or pointer_field) transported by this downstream channel
since CMTS initialization. This is the 64 bit version of
docsIfCmtsDownChnlCtrTotalBytes, and will not be
accessible to SNMPv1 managers.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsDownChannelCounterEntry 4 }
docsIfCmtsDownChnlCtrExtUsedBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"At the CMTS, the total number of DOCSIS data bytes
transported by this downstream channel since CMTS
initialization. The number of data bytes is defined as the
total number of bytes transported in DOCSIS payloads minus
the number of stuff bytes transported in DOCSIS payloads.
This is the 64 bit version of
docsIfCmtsDownChnlCtrUsedBytes, and will not be accessible
to SNMPv1 managers.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsDownChannelCounterEntry 5 }
-- The following table provides operators with input data appropriate
-- for calculating upstream channel utilization, and for determining
-- the traffic characteristics of upstream channels. Operators may use
-- the docsIfCmtsChannelUtilizationTable, or perform their own polling
-- of the docsIfCmtsUpChannelCounterTable objects for utilization
-- determination.
Raftus Expires March 2004 [Page 87]
Internet Draft DOCSIS RF Interface MIB September 2003
-- The first four 32 and 64 objects in this table are mandatory.
-- Vendors may choose to implement the remaining optional objects to
-- provide operators with finer characterization of upstream channel
-- traffic patterns. The 32 bit counter objects are included to provide
-- backward compatibility with SNMPv1 managers, which cannot access 64
-- bit counter objects.
docsIfCmtsUpChannelCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsIfCmtsUpChannelCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is implemented at the CMTS to provide upstream
channel statistics appropriate for channel utilization
calculations."
::= { docsIfCmtsObjects 11 }
docsIfCmtsUpChannelCounterEntry OBJECT-TYPE
SYNTAX DocsIfCmtsUpChannelCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of traffic statistics for a single upstream channel.
For Docsis 2.0 CMTSs, an entry in this table
exists for each ifEntry with an ifType of
docsCableUpstreamChannel (205).
For Docsis 1.x CMTSs, an entry in this table
exists for each ifEntry with an ifType of
docsCableUpstreamInterface (129)."
INDEX { ifIndex }
::= { docsIfCmtsUpChannelCounterTable 1 }
DocsIfCmtsUpChannelCounterEntry ::= SEQUENCE {
docsIfCmtsUpChnlCtrId Integer32,
docsIfCmtsUpChnlCtrTotalMslots Counter32,
docsIfCmtsUpChnlCtrUcastGrantedMslots Counter32,
docsIfCmtsUpChnlCtrTotalCntnMslots Counter32,
docsIfCmtsUpChnlCtrUsedCntnMslots Counter32,
docsIfCmtsUpChnlCtrExtTotalMslots Counter64,
docsIfCmtsUpChnlCtrExtUcastGrantedMslots Counter64,
docsIfCmtsUpChnlCtrExtTotalCntnMslots Counter64,
docsIfCmtsUpChnlCtrExtUsedCntnMslots Counter64,
docsIfCmtsUpChnlCtrCollCntnMslots Counter32,
docsIfCmtsUpChnlCtrTotalCntnReqMslots Counter32,
docsIfCmtsUpChnlCtrUsedCntnReqMslots Counter32,
docsIfCmtsUpChnlCtrCollCntnReqMslots Counter32,
docsIfCmtsUpChnlCtrTotalCntnReqDataMslots Counter32,
docsIfCmtsUpChnlCtrUsedCntnReqDataMslots Counter32,
docsIfCmtsUpChnlCtrCollCntnReqDataMslots Counter32,
docsIfCmtsUpChnlCtrTotalCntnInitMaintMslots Counter32,
docsIfCmtsUpChnlCtrUsedCntnInitMaintMslots Counter32,
Raftus Expires March 2004 [Page 88]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsUpChnlCtrCollCntnInitMaintMslots Counter32,
docsIfCmtsUpChnlCtrExtCollCntnMslots Counter64,
docsIfCmtsUpChnlCtrExtTotalCntnReqMslots Counter64,
docsIfCmtsUpChnlCtrExtUsedCntnReqMslots Counter64,
docsIfCmtsUpChnlCtrExtCollCntnReqMslots Counter64,
docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslots Counter64,
docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslots Counter64,
docsIfCmtsUpChnlCtrExtCollCntnReqDataMslots Counter64,
docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslots Counter64,
docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslots Counter64,
docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslots Counter64
}
docsIfCmtsUpChnlCtrId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The CMTS identification of the upstream channel."
::= { docsIfCmtsUpChannelCounterEntry 1 }
docsIfCmtsUpChnlCtrTotalMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of all minislots
defined for this upstream logical channel. This count
includes all IUCs and SIDs, even those allocated to the
NULL SID for a 2.0 logical channel which is inactive. This
is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalMslots
and is included for back compatibility with SNMPv1
managers. Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 2 }
docsIfCmtsUpChnlCtrUcastGrantedMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of unicast
granted minislots on the upstream logical channel,
regardless of burst type. Unicast granted minislots are
those in which the CMTS assigned bandwidth to any unicast
SID on the logical channel. However this object does not
Raftus Expires March 2004 [Page 89]
Internet Draft DOCSIS RF Interface MIB September 2003
include minislots for reserved IUCs, or grants to SIDs
designated as meaning 'no CM'. This is the 32 bit version
of docsIfCmtsUpChnlCtrExtUcastGrantedMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 3 }
docsIfCmtsUpChnlCtrTotalCntnMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
minislots defined for this upstream logical channel. This
count includes all minislots assigned to a broadcast or
multicast SID on the logical channel. This is the 32 bit
version of docsIfCmtsUpChnlCtrExtTotalCntnMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 4 }
docsIfCmtsUpChnlCtrUsedCntnMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
minislots utilized on the upstream logical channel. For
contention regions, utilized minislots are those in which
the CMTS correctly received an upstream burst from any CM
on the upstream logical channel. This is the 32 bit
version of docsIfCmtsUpChnlCtrExtUsedCntnMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 5 }
docsIfCmtsUpChnlCtrExtTotalMslots OBJECT-TYPE
Raftus Expires March 2004 [Page 90]
Internet Draft DOCSIS RF Interface MIB September 2003
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of all minislots
defined for this upstream logical channel. This count
includes all IUCs and SIDs, even those allocated to the
NULL SID for a 2.0 logical channel which is inactive. This
is the 64 bit version of docsIfCmtsUpChnlCtrTotalMslots,
and will not be accessible to SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 6 }
docsIfCmtsUpChnlCtrExtUcastGrantedMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of unicast
granted minislots on the upstream logical channel,
regardless of burst type. Unicast granted minislots are
those in which the CMTS assigned bandwidth to any unicast
SID on the logical channel. However this object does not
include minislots for reserved IUCs, or grants to SIDs
designated as meaning 'no CM'. This is the 64 bit version
of docsIfCmtsUpChnlCtrUcastGrantedMslots, and will not be
accessible to SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 7 }
docsIfCmtsUpChnlCtrExtTotalCntnMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
minislots defined for this upstream logical channel. This
count includes all minislots assigned to a broadcast or
multicast SID on the logical channel. This is the 64 bit
version of docsIfCmtsUpChnlCtrTotalCntnMslots, and will
not be accessible to SNMPv1 managers.
Support for this object is mandatory.
Raftus Expires March 2004 [Page 91]
Internet Draft DOCSIS RF Interface MIB September 2003
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 8 }
docsIfCmtsUpChnlCtrExtUsedCntnMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
minislots utilized on the upstream logical channel. For
contention regions, utilized minislots are those in which
the CMTS correctly received an upstream burst from any CM
on the upstream logical channel. This is the 64 bit
version of docsIfCmtsUpChnlCtrUsedCntnMslots, and will not
be accessible to SNMPv1 managers.
Support for this object is mandatory.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 9 }
docsIfCmtsUpChnlCtrCollCntnMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
minislots subjected to collisions on the upstream logical
channel. For contention regions, these are the minislots
applicable to bursts that the CMTS detected, but could not
correctly receive. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtCollCntnMslots, and is included for
back compatibility with SNMPv1 managers. Support for this
object is optional. If the object is not supported, a
value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 10 }
docsIfCmtsUpChnlCtrTotalCntnReqMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Raftus Expires March 2004 [Page 92]
Internet Draft DOCSIS RF Interface MIB September 2003
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots defined for this upstream logical
channel. This count includes all minislots for IUC1
assigned to a broadcast or multicast SID on the logical
channel. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtTotalCntnReqMslots, and is included
for back compatibility with SNMPv1 managers.
Support for this object is optional. If the object is not
supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 11 }
docsIfCmtsUpChnlCtrUsedCntnReqMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots utilized on this upstream logical
channel. This count includes all contention minislots for
IUC1 applicable to bursts that the CMTS correctly
received. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtUsedCntnReqMslots, and is included
for back compatibility with SNMPv1 managers. Support for
this object is optional. If the object is not supported,
a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 12 }
docsIfCmtsUpChnlCtrCollCntnReqMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots subjected to collisions on this upstream
logical channel. This includes all contention minislots
for IUC1 applicable to bursts that the CMTS detected, but
could not correctly receive. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtCollCntnReqMslots, and is included
for back compatibility with SNMPv1 managers. Support for
this object is optional. If the object is not supported,
a value of zero is returned.
Raftus Expires March 2004 [Page 93]
Internet Draft DOCSIS RF Interface MIB September 2003
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 13 }
docsIfCmtsUpChnlCtrTotalCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots defined for this upstream logical
channel. This count includes all minislots for IUC2
assigned to a broadcast or multicast SID on the logical
channel. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is optional. If the object is not
supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 14 }
docsIfCmtsUpChnlCtrUsedCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots utilized on this upstream logical
channel. This includes all contention minislots for IUC2
applicable to bursts that the CMTS correctly received.
This is the 32 bit version of
docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is optional. If the object is not
supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 15 }
docsIfCmtsUpChnlCtrCollCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Raftus Expires March 2004 [Page 94]
Internet Draft DOCSIS RF Interface MIB September 2003
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots subjected to collisions on this
upstream logical channel. This includes all contention
minislots for IUC2 applicable to bursts that the CMTS
detected, but could not correctly receive. This is the 32
bit version of
docsIfCmtsUpChnlCtrExtCollCntnReqDataMslots, and is
included for back compatibility with SNMPv1 managers.
Support for this object is optional. If the object is not
supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 16 }
docsIfCmtsUpChnlCtrTotalCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
initial maintenance minislots defined for this upstream
logical channel. This includes all minislots for IUC3
assigned to a broadcast or multicast SID on the logical
channel. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslots,
and is included for back compatibility with SNMPv1
managers. Support for this object is optional. If the
object is not supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 17 }
docsIfCmtsUpChnlCtrUsedCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
initial maintenance minislots utilized on this upstream
logical channel. This includes all contention minislots
for IUC3 applicable to bursts that the CMTS correctly
received. This is the 32 bit version of
docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslots,
and is included for back compatibility with SNMPv1
Raftus Expires March 2004 [Page 95]
Internet Draft DOCSIS RF Interface MIB September 2003
managers. Support for this object is optional. If the
object is not supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 18 }
docsIfCmtsUpChnlCtrCollCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
initial maintenance minislots subjected to collisions on
this upstream logical channel. This includes all
contention minislots for IUC3 applicable to bursts that
the CMTS detected, but could not correctly receive.
This is the 32 bit version of
docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslots,
and is included for back compatibility with SNMPv1
managers. Support for this object is optional. If the
object is not supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 19 }
docsIfCmtsUpChnlCtrExtCollCntnMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of collision
contention minislots on the upstream logical channel.
For contention regions, these are the minislots applicable
to bursts that the CMTS detected, but could not correctly
receive. This is the 64 bit version of
docsIfCmtsUpChnlCtrCollCntnMslots, and will not be
accessible to SNMPv1 managers. Support for this object is
optional. If the object is not supported, a value of zero
is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 20 }
Raftus Expires March 2004 [Page 96]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsUpChnlCtrExtTotalCntnReqMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots defined for this upstream logical
channel. This count includes all minislots for IUC1
assigned to a broadcast or multicast SID on the logical
channel. This is the 64 bit version of
docsIfCmtsUpChnlCtrTotalCntnReqMslots, and will not be
accessible to SNMPv1 managers. Support for this object
is optional. If the object is not supported, a value of
zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 21 }
docsIfCmtsUpChnlCtrExtUsedCntnReqMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots utilized on this upstream logical
channel. This count includes all contention minislots for
IUC1 applicable to bursts that the CMTS correctly
received. This is the 64 bit version of
docsIfCmtsUpChnlCtrUsedCntnReqMslots, and will not be
accessible to SNMPv1 managers. Support for this object is
optional. If the object is not supported, a value of zero
is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 22 }
docsIfCmtsUpChnlCtrExtCollCntnReqMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request minislots subjected to collisions on this upstream
logical channel. This includes all contention minislots
for IUC1 applicable to bursts that the CMTS detected,
but could not correctly receive. This is the 64 bit
Raftus Expires March 2004 [Page 97]
Internet Draft DOCSIS RF Interface MIB September 2003
version of docsIfCmtsUpChnlCtrCollCntnReqMslots, and will
not be accessible to SNMPv1 managers. Support for this
object is optional. If the object is not supported, a
value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 23 }
docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots defined for this upstream logical
channel. This count includes all minislots for IUC2
assigned to a broadcast or multicast SID on the logical
channel. This is the 64 bit version of
docsIfCmtsUpChnlCtrTotalCntnReqDataMslots, and will not be
accessible to SNMPv1 managers. Support for this object is
optional. If the object is not supported, a value of zero
is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 24 }
docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots utilized on this upstream logical
channel. This includes all contention minislots for IUC2
applicable to bursts that the CMTS correctly received.
This is the 64 bit version of
docsIfCmtsUpChnlCtrUsedCntnReqDataMslots, and will not be
accessible to SNMPv1 managers. Support for this object is
optional. If the object is not supported, a value of zero
is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 25 }
Raftus Expires March 2004 [Page 98]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsUpChnlCtrExtCollCntnReqDataMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
request data minislots subjected to collisions on this
upstream logical channel. This includes all contention
minislots for IUC2 applicable to bursts that the CMTS
detected, but could not correctly receive. This is the
64 bit version of
docsIfCmtsUpChnlCtrCollCntnReqDataMslots,
and will not be accessible to SNMPv1 managers. Support
for this object is optional. If the object is not
supported, a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 26 }
docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of initial
maintenance minislots defined for this upstream logical
channel. This count includes all minislots for IUC3
assigned to a broadcast or multicast SID on the logical
channel. This is the 64 bit version of
docsIfCmtsUpChnlCtrTotalCntnInitMaintMslots,
and will not be accessible to SNMPv1 managers. Support for
this object is optional. If the object is not supported,
a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 27 }
docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of initial
maintenance minislots utilized on this upstream logical
channel. This includes all contention minislots for IUC3
Raftus Expires March 2004 [Page 99]
Internet Draft DOCSIS RF Interface MIB September 2003
applicable to bursts that the CMTS correctly received.
This is the 64 bit version of
docsIfCmtsUpChnlCtrUsedCntnInitMaintMslots,
and will not be accessible to SNMPv1 managers. Support for
this object is optional. If the object is not supported,
a value of zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 28 }
docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslots OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current count, from CMTS initialization, of contention
initial maintenance minislots subjected to collisions on
this upstream logical channel. This includes all
contention minislots for IUC3 applicable to bursts that
the CMTS detected, but could not correctly receive.
This is the 64 bit version of
docsIfCmtsUpChnlCtrCollCntnInitMaintMslots, and will not
be accessible to SNMPv1 managers. Support for this object
is optional. If the object is not supported, a value of
zero is returned.
Discontinuities in the value of this counter can occur
at reinitialization of the managed system, and at other
times as indicated by the the value of
ifCounterDiscontinuityTime for the associated ifIndex."
::= { docsIfCmtsUpChannelCounterEntry 29 }
--
-- notification group is for future extension.
--
docsIfNotification OBJECT IDENTIFIER ::= { docsIfMib 2 }
--
-- RFC 2670 Conformance definitions
--
docsIfConformance OBJECT IDENTIFIER ::= { docsIfMib 3 }
docsIfCompliances OBJECT IDENTIFIER ::= { docsIfConformance 1 }
docsIfGroups OBJECT IDENTIFIER ::= { docsIfConformance 2 }
-- compliance statements
Raftus Expires March 2004 [Page 100]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfBasicCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for devices that implement
MCNS/DOCSIS compliant Radio Frequency Interfaces."
MODULE -- docsIfMib
-- unconditionally mandatory groups
MANDATORY-GROUPS {
docsIfBasicGroup
}
-- conditionally mandatory group
GROUP docsIfCmGroup
DESCRIPTION
"This group is implemented only in Cable Modems, not in
Cable Modem Termination Systems."
-- conditionally mandatory group
GROUP docsIfCmtsGroup
DESCRIPTION
"This group is implemented only in Cable Modem Termination
Systems, not in Cable Modems."
OBJECT docsIfDownChannelFrequency
WRITE-SYNTAX Integer32 (54000000..860000000)
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems. The values above are
appropriate for a cable plant using a Sub-Split channel
plan. If DOCSIS is extended to cover other types of
channel plans (and frequency allocations) this object
will be modified accordingly."
OBJECT docsIfDownChannelWidth
WRITE-SYNTAX Integer32 (6000000)
MIN-ACCESS read-only
DESCRIPTION
"It is conformant to implement this object as read-only.
In Cable Modems, this object is always implemented as
read-only. The above value is appropriate for cable
plants running under NTSC (National Television
Standards Committee) standards. If DOCSIS is extended to
work with other standard (e.g. European standards), this
object will be modified accordingly."
OBJECT docsIfDownChannelModulation
WRITE-SYNTAX INTEGER {
qam64 (3),
qam256 (4)
Raftus Expires March 2004 [Page 101]
Internet Draft DOCSIS RF Interface MIB September 2003
}
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfDownChannelInterleave
WRITE-SYNTAX INTEGER {
taps8Increment16(3),
taps16Increment8(4),
taps32Increment4(5),
taps64Increment2(6),
taps128Increment1(7)
}
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfDownChannelPower
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfUpChannelFrequency
WRITE-SYNTAX Integer32 (5000000..42000000)
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems.The values above are
appropriate for a cable plant using a Sub-Split channel
plan. If DOCSIS is extended to cover other types of
channel plans (and frequency allocations) this object
will be modified accordingly."
OBJECT docsIfUpChannelWidth
WRITE-SYNTAX Integer32 (200000..3200000)
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems.The above value is appropriate
for cable plants running under NTSC (National Television
Standards Committee) standards. If DOCSIS is extended to
work with other standard (e.g. European standards), this
object will be modified accordingly."
OBJECT docsIfUpChannelModulationProfile
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
Raftus Expires March 2004 [Page 102]
Internet Draft DOCSIS RF Interface MIB September 2003
OBJECT docsIfUpChannelSlotSize
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfUpChannelRangingBackoffStart
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfUpChannelRangingBackoffEnd
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfUpChannelTxBackoffStart
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfUpChannelTxBackoffEnd
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems;
read-only in Cable Modems."
OBJECT docsIfQosProfPriority
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfMaxUpBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfGuarUpBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
Raftus Expires March 2004 [Page 103]
Internet Draft DOCSIS RF Interface MIB September 2003
OBJECT docsIfQosProfMaxDownBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfMaxTxBurst
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfBaselinePrivacy
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfStatus
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfCmtsServiceAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsSyncInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsUcdInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsInsertInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsInvitedRangingAttempts
MIN-ACCESS read-only
DESCRIPTION
Raftus Expires March 2004 [Page 104]
Internet Draft DOCSIS RF Interface MIB September 2003
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsQosProfilePermissions
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsModType
WRITE-SYNTAX INTEGER {
qpsk (2),
qam16 (3)
}
DESCRIPTION
"Management station may only set 16QAM or QPSK modulation,
but others might be possible based on device
configuration."
::= { docsIfCompliances 1 }
docsIfBasicGroup OBJECT-GROUP
OBJECTS {
docsIfDownChannelId,
docsIfDownChannelFrequency,
docsIfDownChannelWidth,
docsIfDownChannelModulation,
docsIfDownChannelInterleave,
docsIfDownChannelPower,
docsIfUpChannelId,
docsIfUpChannelFrequency,
docsIfUpChannelWidth,
docsIfUpChannelModulationProfile,
docsIfUpChannelSlotSize,
docsIfUpChannelTxTimingOffset,
docsIfUpChannelRangingBackoffStart,
docsIfUpChannelRangingBackoffEnd,
docsIfUpChannelTxBackoffStart,
docsIfUpChannelTxBackoffEnd,
docsIfQosProfPriority,
docsIfQosProfMaxUpBandwidth,
docsIfQosProfGuarUpBandwidth,
docsIfQosProfMaxDownBandwidth,
docsIfQosProfMaxTxBurst,
docsIfQosProfBaselinePrivacy,
docsIfQosProfStatus,
docsIfSigQIncludesContention,
docsIfSigQUnerroreds,
docsIfSigQCorrecteds,
docsIfSigQUncorrectables,
docsIfSigQSignalNoise,
docsIfSigQMicroreflections,
docsIfSigQEqualizationData
Raftus Expires March 2004 [Page 105]
Internet Draft DOCSIS RF Interface MIB September 2003
}
STATUS current
DESCRIPTION
"Group of objects implemented in both Cable Modems and
Cable Modem Termination Systems."
::= { docsIfGroups 1 }
-- The following table was modified to correct naming conventions for
-- Counter32 variables.
docsIfCmGroup OBJECT-GROUP
OBJECTS {
docsIfCmCmtsAddress,
docsIfCmCapabilities,
-- docsIfCmRangingRespTimeout,
docsIfCmRangingTimeout,
docsIfCmStatusValue,
docsIfCmStatusCode,
docsIfCmStatusTxPower,
docsIfCmStatusResets,
docsIfCmStatusLostSyncs,
docsIfCmStatusInvalidMaps,
docsIfCmStatusInvalidUcds,
-- docsIfCmStatusInvalidRangingResp,
docsIfCmStatusInvalidRangingResponses,
-- docsIfCmStatusInvalidRegistrationResp,
docsIfCmStatusInvalidRegistrationResponses,
docsIfCmStatusT1Timeouts,
docsIfCmStatusT2Timeouts,
docsIfCmStatusT3Timeouts,
docsIfCmStatusT4Timeouts,
docsIfCmStatusRangingAborteds,
docsIfCmServiceQosProfile,
docsIfCmServiceTxSlotsImmed,
docsIfCmServiceTxSlotsDed,
docsIfCmServiceTxRetries,
-- docsIfCmServiceTxExceeded,
docsIfCmServiceTxExceededs,
docsIfCmServiceRqRetries,
-- docsIfCmServiceRqExceeded
docsIfCmServiceRqExceededs
}
STATUS current
DESCRIPTION
"Group of objects implemented in Cable Modems."
::= { docsIfGroups 2 }
docsIfCmtsGroup OBJECT-GROUP
OBJECTS {
docsIfCmtsCapabilities,
docsIfCmtsSyncInterval,
docsIfCmtsUcdInterval,
docsIfCmtsMaxServiceIds,
Raftus Expires March 2004 [Page 106]
Internet Draft DOCSIS RF Interface MIB September 2003
-- docsIfCmtsInsertionInterval,
docsIfCmtsInvitedRangingAttempts,
docsIfCmtsInsertInterval,
docsIfCmtsStatusInvalidRangeReqs,
docsIfCmtsStatusRangingAborteds,
docsIfCmtsStatusInvalidRegReqs,
docsIfCmtsStatusFailedRegReqs,
docsIfCmtsStatusInvalidDataReqs,
docsIfCmtsStatusT5Timeouts,
docsIfCmtsCmStatusMacAddress,
docsIfCmtsCmStatusIpAddress,
docsIfCmtsCmStatusDownChannelIfIndex,
docsIfCmtsCmStatusUpChannelIfIndex,
docsIfCmtsCmStatusRxPower,
docsIfCmtsCmStatusTimingOffset,
docsIfCmtsCmStatusEqualizationData,
docsIfCmtsCmStatusValue,
docsIfCmtsCmStatusUnerroreds,
docsIfCmtsCmStatusCorrecteds,
docsIfCmtsCmStatusUncorrectables,
docsIfCmtsCmStatusSignalNoise,
docsIfCmtsCmStatusMicroreflections,
docsIfCmtsServiceCmStatusIndex,
docsIfCmtsServiceAdminStatus,
docsIfCmtsServiceQosProfile,
docsIfCmtsServiceCreateTime,
docsIfCmtsServiceInOctets,
docsIfCmtsServiceInPackets,
docsIfCmtsModType,
docsIfCmtsModControl,
docsIfCmtsModPreambleLen,
docsIfCmtsModDifferentialEncoding,
docsIfCmtsModFECErrorCorrection,
docsIfCmtsModFECCodewordLength,
docsIfCmtsModScramblerSeed,
docsIfCmtsModMaxBurstSize,
docsIfCmtsModGuardTimeSize,
docsIfCmtsModLastCodewordShortened,
docsIfCmtsModScrambler,
docsIfCmtsQosProfilePermissions,
docsIfCmtsCmPtr
}
STATUS current
DESCRIPTION
"Group of objects implemented in Cable Modem Termination
Systems."
::= { docsIfGroups 3 }
-- The following is not necessary and was commented out to avoid
-- SMICng warnings
-- docsIfObsoleteGroup OBJECT-GROUP
Raftus Expires March 2004 [Page 107]
Internet Draft DOCSIS RF Interface MIB September 2003
-- OBJECTS {
-- docsIfCmRangingRespTimeout,
-- docsIfCmtsInsertionInterval
-- }
-- STATUS obsolete
-- DESCRIPTION
-- "Group of objects obsoleted."
-- ::= { docsIfGroups 4 }
--
-- RFC xxxx Conformance definitions
--
docsIfCompliancesV2 OBJECT IDENTIFIER ::= { docsIfConformance 3 }
docsIfGroupsV2 OBJECT IDENTIFIER ::= { docsIfConformance 4 }
-- compliance statements
docsIfBasicComplianceV2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for devices that implement
MCNS/DOCSIS compliant Radio Frequency Interfaces."
MODULE -- docsIfMib
-- unconditionally mandatory groups
MANDATORY-GROUPS {
docsIfBasicGroupV2
}
-- conditionally mandatory group
GROUP docsIfCmGroupV2
DESCRIPTION
"This group is implemented only in Cable Modems, not in
Cable Modem Termination Systems."
-- conditionally mandatory group
GROUP docsIfCmtsGroupV2
DESCRIPTION
"This group is implemented only in Cable Modem Termination
Systems, not in Cable Modems."
OBJECT docsIfDownChannelFrequency
WRITE-SYNTAX Integer32 (47000000..862000000)
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems,
read-only in Cable Modems.
A range of 54MHz to 860MHz is appropriate for a cable
plant using a North American Sub-Split channel plan.
Raftus Expires March 2004 [Page 108]
Internet Draft DOCSIS RF Interface MIB September 2003
The spectrum range has been expanded to accommodate
a lower edge of 47MHz and an upper edge of 862MHz
for some European channel plans.
If DOCSIS is extended to cover other types of channel
plans (and frequency allocations) this object will be
modified accordingly."
OBJECT docsIfDownChannelWidth
WRITE-SYNTAX Integer32 (6000000 | 8000000)
MIN-ACCESS read-only
DESCRIPTION
"It is conformant to implement this object as read-only.
In Cable Modems, this object is always implemented as
read-only. The value of 6 MHz is appropriate for cable
plants running under NTSC (National Television
Standards Committee) standards. The value of 8 MHz is
appropriate for cable plants running under ETSI
standards. For other regional standards, this
object will be modified accordingly."
OBJECT docsIfDownChannelModulation
WRITE-SYNTAX INTEGER {
qam64 (3),
qam256 (4)
}
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfDownChannelInterleave
WRITE-SYNTAX INTEGER {
taps8Increment16(3),
taps16Increment8(4),
taps32Increment4(5),
taps64Increment2(6),
taps128Increment1(7),
taps12increment17(8)
}
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfDownChannelPower
MIN-ACCESS read-only
DESCRIPTION
"Read-write in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelFrequency
WRITE-SYNTAX Integer32 (5000000..65000000)
Raftus Expires March 2004 [Page 109]
Internet Draft DOCSIS RF Interface MIB September 2003
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems.
A range of 5MHz to 42MHz is appropriate for a cable
plant using a North American Sub-Split channel plan.
The spectrum range has been expanded to accommodate
an upper edge of 65MHz for some European channel plans.
If DOCSIS is extended to cover other types of channel
plans (and frequency allocations) this object will
be modified accordingly."
OBJECT docsIfUpChannelWidth
WRITE-SYNTAX Integer32 (200000..6400000)
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems. The above value is appropriate
for cable plants running under NTSC (National Television
Standards Committee) standards. If DOCSIS is extended to
work with other standard (e.g. European standards), this
object will be modified accordingly."
OBJECT docsIfUpChannelModulationProfile
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelSlotSize
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfUpChannelRangingBackoffStart
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelRangingBackoffEnd
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelTxBackoffStart
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
Raftus Expires March 2004 [Page 110]
Internet Draft DOCSIS RF Interface MIB September 2003
read-only in Cable Modems."
OBJECT docsIfUpChannelTxBackoffEnd
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelScdmaActiveCodes
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems. The
number of active codes when SCDMA is in use must range
from 64 to 128, and must be a non-Prime value.
Providing this range allows for the following features
and capabilities:
1) Power management in S-CDMA spreader-on frames
(with a 3 dB spread)
2) Avoidance of code 0
3) Flexible minislot sizes with and without the use of
code 0"
OBJECT docsIfUpChannelScdmaCodesPerSlot
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelScdmaFrameSize
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelScdmaHoppingSeed
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems."
OBJECT docsIfUpChannelType
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelCloneFrom
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelUpdate
Raftus Expires March 2004 [Page 111]
Internet Draft DOCSIS RF Interface MIB September 2003
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfUpChannelPreEqEnable
MIN-ACCESS read-only
DESCRIPTION
"Read-create in Cable Modem Termination Systems,
read-only in Cable Modems."
OBJECT docsIfQosProfPriority
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfMaxUpBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfGuarUpBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfMaxDownBandwidth
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfBaselinePrivacy
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfQosProfStatus
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
Raftus Expires March 2004 [Page 112]
Internet Draft DOCSIS RF Interface MIB September 2003
OBJECT docsIfQosProfMaxTransmitBurst
MIN-ACCESS read-only
DESCRIPTION
"This object is always read-only in Cable Modems.
It is compliant to implement this object as read-only
in Cable Modem Termination Systems."
OBJECT docsIfCmtsServiceAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsSyncInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsUcdInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsInsertInterval
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsInvitedRangingAttempts
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsIfCmtsQosProfilePermissions
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
::= { docsIfCompliancesV2 1 }
docsIfBasicGroupV2 OBJECT-GROUP
OBJECTS {
docsIfDownChannelId,
docsIfDownChannelFrequency,
docsIfDownChannelWidth,
docsIfDownChannelModulation,
docsIfDownChannelInterleave,
docsIfDownChannelPower,
docsIfDownChannelAnnex,
docsIfUpChannelId,
docsIfUpChannelFrequency,
docsIfUpChannelWidth,
Raftus Expires March 2004 [Page 113]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfUpChannelModulationProfile,
docsIfUpChannelSlotSize,
docsIfUpChannelTxTimingOffset,
docsIfUpChannelRangingBackoffStart,
docsIfUpChannelRangingBackoffEnd,
docsIfUpChannelTxBackoffStart,
docsIfUpChannelTxBackoffEnd,
docsIfUpChannelScdmaActiveCodes,
docsIfUpChannelScdmaCodesPerSlot,
docsIfUpChannelScdmaFrameSize,
docsIfUpChannelScdmaHoppingSeed,
docsIfUpChannelType,
docsIfUpChannelCloneFrom,
docsIfUpChannelUpdate,
docsIfUpChannelStatus,
docsIfUpChannelPreEqEnable,
docsIfQosProfPriority,
docsIfQosProfMaxUpBandwidth,
docsIfQosProfGuarUpBandwidth,
docsIfQosProfMaxDownBandwidth,
docsIfQosProfBaselinePrivacy,
docsIfQosProfStatus,
docsIfQosProfMaxTransmitBurst,
docsIfSigQIncludesContention,
docsIfSigQUnerroreds,
docsIfSigQCorrecteds,
docsIfSigQUncorrectables,
docsIfSigQSignalNoise,
docsIfSigQMicroreflections,
docsIfSigQEqualizationData,
docsIfSigQExtUnerroreds,
docsIfSigQExtCorrecteds,
docsIfSigQExtUncorrectables,
docsIfDocsisBaseCapability
}
STATUS current
DESCRIPTION
"Group of objects implemented in both Cable Modems and
Cable Modem Termination Systems."
::= { docsIfGroupsV2 1 }
docsIfCmGroupV2 OBJECT-GROUP
OBJECTS {
docsIfCmCmtsAddress,
docsIfCmCapabilities,
docsIfCmRangingTimeout,
-- docsIfCmRangingRespTimeout,
docsIfCmStatusValue,
docsIfCmStatusCode,
docsIfCmStatusTxPower,
docsIfCmStatusResets,
docsIfCmStatusLostSyncs,
Raftus Expires March 2004 [Page 114]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmStatusInvalidMaps,
docsIfCmStatusInvalidUcds,
docsIfCmStatusInvalidRangingResponses,
docsIfCmStatusInvalidRegistrationResponses,
docsIfCmStatusT1Timeouts,
docsIfCmStatusT2Timeouts,
docsIfCmStatusT3Timeouts,
docsIfCmStatusT4Timeouts,
docsIfCmStatusRangingAborteds,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType,
docsIfCmStatusEqualizationData,
docsIfCmStatusUCCs,
docsIfCmStatusUCCFails,
docsIfCmServiceQosProfile,
docsIfCmServiceTxSlotsImmed,
docsIfCmServiceTxSlotsDed,
docsIfCmServiceTxRetries,
docsIfCmServiceTxExceededs,
docsIfCmServiceRqRetries,
docsIfCmServiceRqExceededs,
docsIfCmServiceExtTxSlotsImmed,
docsIfCmServiceExtTxSlotsDed
}
STATUS current
DESCRIPTION
"Group of objects implemented in Cable Modems."
::= { docsIfGroupsV2 2 }
docsIfCmtsGroupV2 OBJECT-GROUP
OBJECTS {
docsIfCmtsCapabilities,
docsIfCmtsSyncInterval,
docsIfCmtsUcdInterval,
docsIfCmtsMaxServiceIds,
-- docsIfCmtsInsertionInterval,
docsIfCmtsInvitedRangingAttempts,
docsIfCmtsInsertInterval,
docsIfCmtsStatusInvalidRangeReqs,
docsIfCmtsStatusRangingAborteds,
docsIfCmtsStatusInvalidRegReqs,
docsIfCmtsStatusFailedRegReqs,
docsIfCmtsStatusInvalidDataReqs,
docsIfCmtsStatusT5Timeouts,
docsIfCmtsCmStatusMacAddress,
docsIfCmtsCmStatusDownChannelIfIndex,
docsIfCmtsCmStatusUpChannelIfIndex,
docsIfCmtsCmStatusRxPower,
docsIfCmtsCmStatusTimingOffset,
docsIfCmtsCmStatusEqualizationData,
docsIfCmtsCmStatusValue,
Raftus Expires March 2004 [Page 115]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsCmStatusUnerroreds,
docsIfCmtsCmStatusCorrecteds,
docsIfCmtsCmStatusUncorrectables,
docsIfCmtsCmStatusSignalNoise,
docsIfCmtsCmStatusMicroreflections,
docsIfCmtsCmStatusExtUnerroreds,
docsIfCmtsCmStatusExtCorrecteds,
docsIfCmtsCmStatusExtUncorrectables,
docsIfCmtsCmStatusDocsisRegMode,
docsIfCmtsCmStatusModulationType,
docsIfCmtsCmStatusInetAddressType,
docsIfCmtsCmStatusInetAddress,
docsIfCmtsCmStatusValueLastUpdate,
docsIfCmtsCmStatusHighResolutionTimingOffset,
docsIfCmtsServiceAdminStatus,
docsIfCmtsServiceQosProfile,
docsIfCmtsServiceCreateTime,
docsIfCmtsServiceInOctets,
docsIfCmtsServiceInPackets,
docsIfCmtsServiceNewCmStatusIndex,
docsIfCmtsModType,
docsIfCmtsModControl,
docsIfCmtsModPreambleLen,
docsIfCmtsModDifferentialEncoding,
docsIfCmtsModFECErrorCorrection,
docsIfCmtsModFECCodewordLength,
docsIfCmtsModScramblerSeed,
docsIfCmtsModMaxBurstSize,
docsIfCmtsModGuardTimeSize,
docsIfCmtsModLastCodewordShortened,
docsIfCmtsModScrambler,
docsIfCmtsModByteInterleaverDepth,
docsIfCmtsModByteInterleaverBlockSize,
docsIfCmtsModPreambleType,
docsIfCmtsModTcmErrorCorrectionOn,
docsIfCmtsModScdmaInterleaverStepSize,
docsIfCmtsModScdmaSpreaderEnable,
docsIfCmtsModScdmaSubframeCodes,
docsIfCmtsModChannelType,
docsIfCmtsQosProfilePermissions,
docsIfCmtsCmPtr,
docsIfCmtsChannelUtilizationInterval,
docsIfCmtsChannelUtUtilization,
docsIfCmtsDownChnlCtrId,
docsIfCmtsDownChnlCtrTotalBytes,
docsIfCmtsDownChnlCtrUsedBytes,
docsIfCmtsDownChnlCtrExtTotalBytes,
docsIfCmtsDownChnlCtrExtUsedBytes,
docsIfCmtsUpChnlCtrId,
docsIfCmtsUpChnlCtrTotalMslots,
docsIfCmtsUpChnlCtrUcastGrantedMslots,
docsIfCmtsUpChnlCtrTotalCntnMslots,
Raftus Expires March 2004 [Page 116]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfCmtsUpChnlCtrUsedCntnMslots,
docsIfCmtsUpChnlCtrExtTotalMslots,
docsIfCmtsUpChnlCtrExtUcastGrantedMslots,
docsIfCmtsUpChnlCtrExtTotalCntnMslots,
docsIfCmtsUpChnlCtrExtUsedCntnMslots,
docsIfCmtsUpChnlCtrCollCntnMslots,
docsIfCmtsUpChnlCtrTotalCntnReqMslots,
docsIfCmtsUpChnlCtrUsedCntnReqMslots,
docsIfCmtsUpChnlCtrCollCntnReqMslots,
docsIfCmtsUpChnlCtrTotalCntnReqDataMslots,
docsIfCmtsUpChnlCtrUsedCntnReqDataMslots,
docsIfCmtsUpChnlCtrCollCntnReqDataMslots,
docsIfCmtsUpChnlCtrTotalCntnInitMaintMslots,
docsIfCmtsUpChnlCtrUsedCntnInitMaintMslots,
docsIfCmtsUpChnlCtrCollCntnInitMaintMslots,
docsIfCmtsUpChnlCtrExtCollCntnMslots,
docsIfCmtsUpChnlCtrExtTotalCntnReqMslots,
docsIfCmtsUpChnlCtrExtUsedCntnReqMslots,
docsIfCmtsUpChnlCtrExtCollCntnReqMslots,
docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslots,
docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslots,
docsIfCmtsUpChnlCtrExtCollCntnReqDataMslots,
docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslots,
docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslots,
docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslots
}
STATUS current
DESCRIPTION
"Group of objects implemented in Cable Modem Termination
Systems."
::= { docsIfGroupsV2 3 }
END
5. Acknowledgments
This document is a production of the Docsis 2.0 OSS Working Group.
It is a revision based on RFC2670, "Radio Frequency (RF)
Interface Management Information Base for DOCSIS compliant RF
interfaces" [RFC2670].
The current editor wishes to express gratitude to Rich Prodan, Aviv
Goren, Greg Nakanishi, Rich Woundy, Eduardo Cardona, and Adi Shaliv
for their valued advice and opinions.
The current editor is also very grateful to colleague Andr‰ Lejeune
for his timely and intelligent advice and assistance.
Raftus Expires March 2004 [Page 117]
Internet Draft DOCSIS RF Interface MIB September 2003
6. Revision History
6.1. Scope
This MIB in this document has been developed to accommodate
DOCSIS 2.0 devices and their system capabilities. The MIB is an
update to RFC2670 with the additional incorporation of EuroDocsis
specific items and the DOCS_IF_EXT mib.
6.2. Extension
We have maintained the MIB objects as defined in RFC 2670. In some
cases new mib objects have been created with identical
functionality but greater capacity (ie 32 to 64 bits). In these
situations, both the original 32 bit objects and the new 64 bit
objects must be implemented.
7. Normative References
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets",
STD 16, RFC 1155, May 1990.
[RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions",
STD 16, RFC 1212, March 1991.
[RFC1215] Rose, M., "A Convention for Defining Traps for use with
the SNMP", RFC 1215, March 1991.
[RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901,
January 1996.
[RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2026] Bradner, S., "The Internet Standards Process - Revision
3", BCP 9, RFC 2026, October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction to Version 3 of the Internet-standard
Raftus Expires March 2004 [Page 118]
Internet Draft DOCSIS RF Interface MIB September 2003
Network Management Framework", RFC 2570, April 1999.
[RFC2571] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April
1999.
[RFC2572] Case, J., Harrington D., Presuhn R. and B. Wijnen,
"Message Processing and Dispatching for the Simple Network
Management Protocol (SNMP)", RFC 2572, April 1999.
[RFC2573] Levi, D., Meyer, P. and B. Stewart, "SNMP Applications",
RFC 2573, April 1999.
[RFC2574] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", RFC 2580, STD 58, April 1999.
[RFC2669] StJohns, M. , "Cable Device Management Information Base
for DOCSIS Compliant Cable Modems and Cable Modem
Termination Systems", RFC2669, August 1999.
[RFC2819] Waldbusser, S., "Remote Network Monitoring Management
Information Base", STD 59, RFC 2819, May 2000.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB using SMIv2", RFC 2863, June 2000.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", STD 62, RFC 3414, December 2002.
[RFC3415] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", STD 62, RFC 3415, December
2002.
Raftus Expires March 2004 [Page 119]
Internet Draft DOCSIS RF Interface MIB September 2003
[1] Woundy, R., "Baseline Privacy Interface Management
Information Base for DOCSIS Compliant Cable Modems
and Cable Modem Termination Systems", RFC3083, March 2001.
[2] "Data-Over-Cable Service Interface Specifications: Cable Modem
Radio Frequency Interface Specification SP-RFI-I06-010829",
DOCSIS, August 2001, http://www.cablemodem.com.
[3] "Data-Over-Cable Service Interface Specifications: Cable
Modem Radio Frequency Interface Specification SP-RFIv1.1-I09-
020830", DOCSIS, August 2002, http://www.cablemodem.com.
[4] "Data-Over-Cable Service Interface Specifications: Radio
Frequency Interface Specification SP-RFIv2.0-I04-030730",
DOCSIS 2.0 July 2003.
[5] "Data-Over-Cable Service Interface Specifications: Operations
Support System Interface Specification SP-OSSIv2.0-I04-030730",
DOCSIS 2.0 July 2003.
[6] Proakis, John G., "Digital Communications, 3rd Edition",
McGraw-Hill, New York, New York, 1995, ISBN 0-07-051726-6
[7] "Transmission Systems for Interactive Cable Television
Services, Annex B", J.112, International Telecommunications
Union, March 1998.
[8] "Document for the certification of EuroDOCSIS CMs and CMTSs,
Version 3.3", EuroDOCSIS, February 2000.
[9] "Adapted MIB-definitions and a clarification for MPEG-related
issues for EuroDOCSIS cable modem systems v1.01", tComLabs,
May 2000.
8. Informative References
[RFC2670] StJohns, M., "Radio Frequency (RF) Interface Management
Information Base for MCNS/DOCSIS compliant RF interfaces",
RFC 2670, August 1999.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
9. Security Considerations
This MIB relates to a system which will provide metropolitan public
Raftus Expires March 2004 [Page 120]
Internet Draft DOCSIS RF Interface MIB September 2003
internet access. As such, improper manipulation of the objects
represented by this MIB may result in denial of service to a large
number of end-users. In addition, manipulation of the
docsIfCmServiceQosProfile, docsIfCmtsServiceQosProfile, and the
elements of docsIfQosProfileTable and docsIfCmtsModulationTable may
allow an end-user to improve their service response or diminish
other subscriber's service response.
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is
no control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the
use of the User-based Security Model RFC 2574 [12] and the View-
based Access Control Model RFC 2575 [15] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET
(change/create/delete) them.
10. Changes from RFC2670
Upstream now separated into 'physical interfaces' and 'logical
channels'. An instance of the docsIfUpstreamChannelTable exists
for each 'logical channel'. The IANA ifType for 'logical channels'
is 205. The IANA ifType for 'physical interfaces' remains at 129.
Object docsIfDownChannelAnnex added to
docsIfDownstreamChannelTable. This object originated in the
EuroDocsis specifications.
Nine new objects added to the docsIfUpstreamChannelTable. One
describes the channel type in use. Four are specific S-CDMA
parameters. Three are used in the creation of a temporary
inactive upstream row so the S-CDMA parameters may be manipulated
'offline'. One object has been added to enable/disable
pre-equalization on the upstream channel.
Object docsIfQosProfMaxTransmitBurst has been added to the
docsIfQosProfileTable to replace deprecated object
Raftus Expires March 2004 [Page 121]
Internet Draft DOCSIS RF Interface MIB September 2003
docsIfQosProfMaxTxBurst. This fixes a range error caused by switch
to recording as bytes instead of minislots.
Three new 64 bit counters added to the docsIfSignalQualityTable to
extend the capacity of existing 32 bit counters.
A new base object docsIfDocsisBaseCapability has been added which
mirrors the functionality of the docsifExt mib object
docsIfDocsisCapability, extended to include Docsis 2.0.
Three new objects added to the docsIfCmStatusTable. One indicates
the current modulation type. The second mirrors the functionality
of the docsIfExt object docsIfDocsisOperMode, while clarifying that
it applies to the COS/QOS mode used by the device. The third new
object indicates equalization data at the CM.
Two new 64 bit counters added to the docsIfCmServiceTable to extend
the capacity of existing 32 bit counters.
Seven new objects added to the docsIfCmtsCmStatusTable. Three are
64 bit counters, two add ipv6 capability, and one indicates the CM
modulation type in use. The remaining object mirrors the
functionality of the docsIfExt object docsIfCmtsCmStatusDocsisMode,
while clarifying that it applies to the COS/QOS mode used by the
device.
One object added to the docsIfCmtsServiceTable to fix a range error
in an existing object, that has been deprecated.
Eight new objects added to the docsIfCmtsModulationTable. Seven of
these describe ATDMA/S-CDMA channel parameters, while the other
describes modulation attributes common to all modulation types.
One new object and three new tables added to provide CMTS upstream
and downstream channel utilization data.
Enumerated values for object docsIfDownChannelInterleave have been
expanded to include a EuroDocsis value.
Enumerated values for object docsIfCmtsModIntervalUsageCode have
been expanded to include new Docsis 2.0 values.
Enumerated values for object docsIfCmtsModType have been expanded
to include new Docsis 2.0 values.
Compliance statements have been updated to reflect new objects and
to describe EuroDocsis specific implementation features.
The descriptions of objects docsIfCmtsStatusInvalidRegReqs and
docsIfCmtsStatusFailedRegReqs have been clarified.
Separated references into normative and informative.
Raftus Expires March 2004 [Page 122]
Internet Draft DOCSIS RF Interface MIB September 2003
11. Conflict Resolution with docsIfExt MIB
The docsIfExt MIB originated as an engineering change notification
(ECN) to the Docsis 1.1 specifications, and consisted of three
objects - two for CM implementation and one for the CMTS. These
three objects have been incorporated into this new version of the
RF MIB, and have been assigned new object identifiers.
The following process has been used to accomplish the deprecation
of the docsIfExt MIB:
1) Created Docsis ECNs (oss2-n-02016/oss-n-02017) that required
Docsis 1.1/2.0 implementations to support the new location of the
three docsIfExt objects in the RF MIB.
2) The same ECNs updated the docsCableDeviceTrap MIB to reference
the new location of the three docsIfExt objects, and deprecated
the former references.
3) The same ECNs deprecated the docsIfExt MIB.
Following these steps, the state of affairs is:
a) Docsis 1.1 MUST support new RF MIB docsIfExt objects.
b) Docsis 1.1 MAY support remaining RF MIB 2.0 objects.
c) Docsis 1.1 MAY support former docsIfExt MIB objects.
d) Docsis 2.0 MUST support all new RF MIB objects.
e) Docsis 2.0 MUST NOT support former docsIfExt MIB objects.
12. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances
of licenses to be made available, or the result of an attempt made
to obtain a general license or permission for the use of such
proprietary rights by implementers or users of this specification
can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Raftus Expires March 2004 [Page 123]
Internet Draft DOCSIS RF Interface MIB September 2003
13. Author's Address
David Raftus
Terayon Canada Ltd
340 Terry Fox Drive, Suite 202
Ottawa Ontario
Canada
Phone: +1 613 592 1052 ext 222
E-mail: david.raftus@terayon.com
14. Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Funding for the RFC Editor function is currently provided by the
Internet Society.
Raftus Expires March 2004 [Page 124]
