IPFIX working group
Internet Draft EDITOR: B. Claise
draft-ietf-ipfix-protocol-14.txt Cisco Systems
Expires: November 13, 2005 May 2005
IPFIX Protocol Specification
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on November 13, 2005.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This document specifies the IPFIX protocol that serves for
transmitting IP traffic flow information over the network. In order
to transmit IP traffic flow information from an exporting process to
an information collecting process, a common representation of flow
Claise, et. al Standard Track [Page 1]
IPFIX Protocol Specification May 2005
data and a standard means of communicating them is required. This
document describes how the IPFIX data and templates records are
carried over a congestion-aware transport protocol from an IPFIX
exporting process to an IPFIX collecting process.
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119.
Table of Contents
1. Introduction...................................................4
1.1 IPFIX Documents Overview.....................................4
2. Terminology....................................................5
2.1 Terminology Summary Table....................................9
3. IPFIX Message Format..........................................10
3.1 Message Header Format.......................................12
3.2 Field Specifier Format......................................13
3.3 Set and Set Header Format...................................15
3.3.1 Set Format...............................................15
3.3.2 Set Header Format........................................16
3.4 Record Format...............................................16
3.4.1 Template Record Format...................................16
3.4.2 Options Template Record Format...........................19
3.4.2.1 Scope...................................................19
3.4.2.2 Options Template Record Format..........................20
3.4.3 Data Record Format.......................................22
4. Specific Reporting Requirements...............................23
4.1 The Metering Process Statistics Option Template.............24
4.2 The Metering Process Reliability Statistics Option Template.25
4.3 The Exporting Process Reliability Statistics Option Template25
4.4 The Flow Keys Option Template...............................26
5. IPFIX Message Header "Export Time" and Flow Record Time.......27
6. Linkage with the Information Model............................28
6.1 Encoding of IPFIX Data Types................................28
6.1.1 Integral Data Types......................................28
6.1.2 Address Types............................................28
6.1.3 float32..................................................28
6.1.4 boolean..................................................28
6.1.5 string and octetarray....................................28
6.1.6 dateTimeSeconds..........................................29
6.1.7 dateTimeMilliSeconds.....................................29
6.1.8 dateTimeNanoSeconds......................................29
6.1.9 dateTimeMicroSeconds.....................................29
6.2 Reduced Size Encoding of Integer Types......................29
7. Variable Length Information Element...........................30
Claise, et. al Standard Track [Page 2]
IPFIX Protocol Specification May 2005
8. Template Management...........................................31
9. The Collecting Process's Side.................................34
10. Transport Protocol...........................................36
10.1 Transport Compliance and Transport Usage...................36
10.2 SCTP.......................................................37
10.2.1 Congestion Avoidance.....................................37
10.2.2 Reliability..............................................37
10.2.3 MTU......................................................38
10.2.4 Exporting Process........................................38
10.2.4.1 Association Establishment...............................38
10.2.4.2 Association Shutdown....................................38
10.2.4.3 Stream..................................................39
10.2.4.4 Template Management.....................................39
10.2.5 Collecting Process.......................................39
10.2.6 Failover.................................................40
10.3 UDP........................................................40
10.3.1 Congestion Avoidance.....................................40
10.3.2 Reliability..............................................40
10.3.3 MTU......................................................41
10.3.4 Port Numbers.............................................41
10.3.5 Exporting Process........................................41
10.3.6 Template Management......................................41
10.3.7 Collecting Process.......................................42
10.3.8 Failover.................................................43
10.4 TCP........................................................43
10.4.1 Connection Management....................................43
10.4.1.1 Connection Establishment................................43
10.4.1.2 Graceful Connection Release.............................43
10.4.1.3 Restarting Interrupted Connections......................44
10.4.1.4 Failover................................................44
10.4.2 Data Transmission........................................44
10.4.2.1 IPFIX Message Encoding..................................44
10.4.2.2 Templates...............................................45
10.4.2.3 Congestion Handling and Reliability.....................45
11. Security Considerations......................................46
11.1 IPsec Usage................................................46
11.1.1 Selectors................................................47
11.1.2 Mode.....................................................47
11.1.3 Key Management...........................................47
11.1.4 Security Policy..........................................47
11.1.5 Authentication...........................................47
11.1.6 Availability.............................................48
11.2 TLS Usage..................................................48
11.3 Protection against DoS attacks.............................48
11.4 When IPsec or TLS is not an option.........................49
11.5 Logging an IPFIX Attack....................................49
12. IANA Considerations..........................................50
12.1 Numbers used in the Protocol...............................50
12.2 Numbers used in the Information Model......................50
Claise, et. al Standard Track [Page 3]
IPFIX Protocol Specification May 2005
13. Examples.....................................................50
13.1 Message Header Example.....................................51
13.2 Template Set Examples......................................51
13.2.1 Template Set using IETF specified Information Elements...51
13.2.2 Template Set using Enterprise Specific Information
Elements.........................................................52
13.3 Data Set Example...........................................53
13.4 Options Template Set Examples..............................55
13.4.1 Options Template Set using IETF specified Information
Elements.........................................................55
13.4.2 Options Template Set using enterprise-specific
Information Elements.............................................55
13.4.3 Options Template Set using an enterprise-specific scope..56
13.4.4 Data Set using an enterprise-specific scope..............57
14. References...................................................58
14.1 Normative References.......................................58
14.2 Informative References.....................................58
15. Acknowledgments..............................................59
1. Introduction
A data network with IP traffic, primarily consists of IP Flows
passing through the network elements of the network. It is often
interesting, useful or even a requirement to have access to
information about these flows that pass through the network elements
for administrative or other purposes. The IPFIX collecting process
should be able to receive the flow information passing through
multiple network elements within the data network. This requires
uniformity in the method of representing the flow information and
the means of communicating the flows from the network elements to
the collection point. This document specifies the protocol to
achieve these aforementioned requirements. This document specifies
in detail the representation of different flows, the additional data
required for flow interpretation, packet format, transport
mechanisms used, security concerns, etc.
1.1 IPFIX Documents Overview
The IPFIX protocol provides network administrators with access to IP
flow information. The architecture for the export of measured IP
flow information out of an IPFIX exporting process to a collecting
process is defined in [IPFIX-ARCH], per the requirements defined in
[RFC3917]. This document specifies how IPFIX data record and
templates are carried via a congestion-aware transport protocol from
IPFIX exporting processes to IPFIX collecting process. IPFIX has a
Claise, et. al Standard Track [Page 4]
IPFIX Protocol Specification May 2005
formal description of IPFIX information elements, their name, type
and additional semantic information, as specified in [IPFIX-INFO].
Finally [IPFIX-AS] describes what type of applications can use the
IPFIX protocol and how they can use the information provided. It
furthermore shows how the IPFIX framework relates to other
architectures and frameworks.
2. Terminology
The definitions of the basic terms like IP Traffic Flow, Exporting
Process, Collecting Process, Observation Points, etc. are
semantically identical with those found in the IPFIX requirements
document [RFC3917]. Some of the terms have been expanded for more
clarity when defining the protocol. Additional terms required for
the protocol has also been defined. Definitions in this document
and in [IPFIX-ARCH] are equivalent, except that definitions which
are only relevant to the IPFIX protocol only appear here.
The terminology summary table in Section 2.1 gives a quick overview
of the relationships between some of the different terms defined.
Observation Point
An Observation Point is a location in the network where IP packets
can be observed. Examples include: a line to which a probe is
attached, a shared medium, such as an Ethernet-based LAN, a single
port of a router, or a set of interfaces (physical or logical) of a
router.
Note that one Observation Point may be a superset of several
other Observation Points. For example, one Observation Point can be
an entire line card. This would be the superset of the
individual Observation Points at the line card's interfaces.
Observation Domain
An Observation Domain is the largest set of Observation Points for
which Flow information can be aggregated by a Metering Process.
Each Observation Domain presents itself using a unique ID to the
Collecting Process to identify the IPFIX Messages it generates. For
example, a router line card may be an observation domain if it is
composed of several interfaces: each of which is an Observation
Claise, et. al Standard Track [Page 5]
IPFIX Protocol Specification May 2005
Point. Every Observation Point is associated with an Observation
Domain.
IP Traffic Flow or Flow
There are several definitions of the term 'flow' being used by the
Internet community. Within the context of IPFIX we use the
following definition:
A Flow is defined as a set of IP packets passing an Observation
Point in the network during a certain time interval. All packets
belonging to a particular Flow have a set of common properties.
Each property is defined as the result of applying a function to the
values of:
1. one or more packet header field (e.g. destination IP address),
transport header field (e.g. destination port number), or
application header field (e.g. RTP header fields [RFC1889])
2. one or more characteristics of the packet itself (e.g. number
of MPLS labels, etc...)
3. one or more of fields derived from packet treatment (e.g. next
hop IP address, the output interface, etc...)
A packet is defined to belong to a Flow if it completely satisfies
all the defined properties of the Flow.
This definition covers the range from a Flow containing all packets
observed at a network interface to a Flow consisting of just a
single packet between two applications. It includes packets
selected by a sampling mechanism.
Flow Key
Each of the fields which
1. Belong to the packet header (e.g. destination IP address)
2. Are a property of the packet itself (e.g. packet length)
3. Are derived from packet treatment (e.g. AS number)
Claise, et. al Standard Track [Page 6]
IPFIX Protocol Specification May 2005
and which are used to define a Flow are termed Flow Keys.
Flow Record
A Flow Record contains information about a specific Flow that was
observed at an Observation Point. A Flow Record contains measured
properties of the Flow (e.g. the total number of bytes for all the
Flow's packets) and usually characteristic properties of the Flow
(e.g. source IP address).
Metering Process
The Metering Process generates Flow Records. Inputs to the process
are packet headers and characteristics observed at an Observation
Point and packet treatment at the Observation Point (for example the
selected output interface).
The Metering Process consists of a set of functions that includes
packet header capturing, timestamping, sampling, classifying, and
maintaining Flow Records.
The maintenance of Flow Records may include creating new records,
updating existing ones, computing Flow statistics, deriving further
Flow properties, detecting Flow expiration, passing Flow Records to
the Exporting Process, and deleting Flow Records.
Exporting Process
The Exporting Process sends Flow Records to one or more Collecting
Processes. The Flow Records are generated by one or more Metering
Processes.
Exporter
A device which hosts one or more Exporting Processes is termed an
Exporter.
IPFIX Device
An IPFIX Device hosts at least one Observation Point, a Metering
Process and an Exporting Process.
Collecting Process
Claise, et. al Standard Track [Page 7]
IPFIX Protocol Specification May 2005
A Collecting Process receives Flow Records from one or more
Exporting Processes. The Collecting Process might process or store
received Flow Records, but such actions are out of scope for this
document.
Collector
A device which hosts one or more Collecting Processes is termed a
Collector.
Template
Template is an ordered sequence of <type, length> pairs, used to
completely identify the structure and semantics of a particular set
of information that needs to be communicated from an IPFIX Device to
a Collector. Each Template is uniquely identifiable by means of a
Template ID.
IPFIX Message
An IPFIX Message is a message originating at the Exporting Process
that carries the IPFIX records of this Exporting Process and whose
destination is a Collecting Process. An IPFIX Message is
encapsulated within a transport layer.
Message Header
The Message Header is the first part of an IPFIX Message, which
provides basic information about the message such as the IPFIX
version, length of the message, message sequence number, etc.
Template Record
A Template Record defines the structure and interpretation of fields
in a Data Record.
Data Record
A Data Record is a record that contains values of the parameters
corresponding to a Template Record.
Options Template Record
Claise, et. al Standard Track [Page 8]
IPFIX Protocol Specification May 2005
An Options Template Record is a Template Record that defines the
structure and interpretation of fields in a Data Record, including
defining how to scope the applicability of the Data Record.
Set
Set is a generic term for a collection of records that have a
similar structure. In an IPFIX Message, one or more Sets follow the
Message Header.
There are three different types of Sets: Template Set, Options
Template Set, and Data Set.
Template Set
A Template Set is a collection of one or more Template Records that
have been grouped together in an IPFIX Message.
Options Template Set
An Options Template Set is a collection of one or more Options
Template Records that have been grouped together in an IPFIX
Message.
Data Set
A Data Set is one or more Data Records, of the same type, that are
grouped together in an IPFIX Message. Each Data Record is
previously defined by a Template Record or an Options Template
Record.
Information Element
An Information Element is a protocol and encoding independent
description of an attribute which may appear in an IPFIX Record.
The IPFIX information model [IPFIX-INFO] defines the base set of
Information Elements for IPFIX. The type associated with an
Information Element indicates constraints on what it may contain and
also determines the valid encoding mechanisms for use in IPFIX.
2.1
Terminology Summary Table
Claise, et. al Standard Track [Page 9]
IPFIX Protocol Specification May 2005
+------------------+---------------------------------------------+
| | Contents |
| +--------------------+------------------------+
| Set | Template | Record |
+------------------+--------------------+------------------------+
| Data Set | / | Data Record(s) |
+------------------+--------------------+------------------------+
| Template Set | Template Record(s) | / |
+------------------+--------------------+------------------------+
| Options Template | Options Template | / |
| Set | Record(s) | |
+------------------+--------------------+------------------------+
Figure A: Terminology Summary Table
A Data Set is composed of Data Record(s). No Template Record is
included. A Template Record or an Options Template Record defines
the Data Record.
A Template Set contains only Template Record(s).
An Options Template Set contains only Options Template Record(s).
3. IPFIX Message Format
An IPFIX Message consists of a Message Header followed by one or
more Sets. The Sets can be any of the possible three types: Data
Set, Template Set or Options Template Set.
The format of the IPFIX Message is shown in Figure B.
+----------------------------------------------------+
| Message Header |
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
...
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
Claise, et. al Standard Track [Page 10]
IPFIX Protocol Specification May 2005
Figure B: IPFIX Message format
The Exporter MUST code all binary integers of the Message Header and
the different Sets in network byte order (also known as the big-
endian byte ordering).
Following are some examples of IPFIX Messages:
1. An IPFIX Message consisting of interleaved Template, Data, and
Options Template Sets - A newly created Template is exported as soon
as possible. So if there is already an IPFIX Message with a Data
Set that is being prepared for export, the Template and Option
Template Sets are interleaved with this information, subject to
availability of space.
+--------+--------------------------------------------------------+
| | +----------+ +---------+ +-----------+ +---------+ |
|Message | | Template | | Data | | Options | | Data | |
| Header | | Set | | Set | ... | Template | | Set | |
| | | | | | | Set | | | |
| | +----------+ +---------+ +-----------+ +---------+ |
+--------+--------------------------------------------------------+
Figure C: IPFIX Message example 1
2. An IPFIX Message consisting entirely of Data Sets - After the
appropriate Template Records have been defined and transmitted to
the Collecting Process, the majority of IPFIX Messages consist
solely of Data Sets.
+--------+----------------------------------------------+
| | +---------+ +---------+ +---------+ |
|Message | | Data | | Data | | Data | |
| Header | | Set | ... | Set | ... | Set | |
| | +---------+ +---------+ +---------+ |
+--------+----------------------------------------------+
Figure D: IPFIX Message example 2
3. An IPFIX Message consisting entirely of Template and Options
Template Sets - When UDP is used as the transport protocol, Template
Sets and Option Template Sets MUST be sent periodically to ensure
Claise, et. al Standard Track [Page 11]
IPFIX Protocol Specification May 2005
that the Collecting Process has the Template Records and Options
Template Records when the corresponding Data Records are received.
+--------+-------------------------------------------------+
| | +----------+ +----------+ +----------+ |
|Message | | Template | | Template | | Options | |
| Header | | Set | ... | Set | ... | Template | |
| | | | | | | Set | |
| | +----------+ +----------+ +----------+ |
+--------+-------------------------------------------------+
Figure E: IPFIX Message example 3
3.1 Message Header Format
The format of the IPFIX Message Header format is shown in Figure F.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Export Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure F: IPFIX Message Header format
Message Header Field Descriptions
Version
Version of Flow Record format exported in this message. The
value of this field is 0x000a for the current version.
Length
Total Length is the length of the IPFIX Message, measured in
octets, including Message Header and Set(s).
Export Time
Claise, et. al Standard Track [Page 12]
IPFIX Protocol Specification May 2005
Time in seconds since 0000 UTC Jan 1st 1970, at which the
IPFIX Message Header leaves the Exporter.
Sequence Number
Incremental sequence counter modulo 2^32 of all IPFIX
Messages sent on this stream from the current Observation
Domain by the Exporting Process. This value SHOULD be used
by the Collecting Process to identify whether any IPFIX
Messages have been missed.
Source ID
A 32-bit identifier of the Observation Domain that is
locally unique to the Exporting Process. The Exporting
Process uses the Source ID to uniquely identify to the
Collecting Process the Observation Domain that metered the
Flows. Collecting Processes SHOULD use the combination the
combination of the Exporter (exporterIPv4Address,
exporterIPv6Address, or exportingProcessId) and the Source
ID field to separate different export streams originating
from the same Exporting Process. The Source ID SHOULD be 0
when no specific Source ID is relevant for the entire IPFIX
Message. For example, when exporting the Exporting Process
Statistics, or in case of hierarchy of Collector when
aggregated data records are exported. The Source ID MUST be
zero when the IPFIX Message contains data records with
different Source ID values defined as scopes.
3.2 Field Specifier Format
Vendors need the ability to define proprietary Information Elements,
because, for example, they are delivering a pre-standards product,
or the Information Element is in some way commercially sensitive.
This section describes the Field Specifier format for both IETF
specified Information Elements [IPFIX-INFO] and enterprise-specific
Information Elements.
The Information Elements are identified by the Information Element
identifier. When the Enterprise bit is set to 0, the corresponding
Information Element identifier will report an IETF specified
Information Element, and the Enterprise Number MUST NOT be present.
When the Enterprise bit is set to 1, the corresponding Information
Element identifier will report an enterprise-specific Information
Claise, et. al Standard Track [Page 13]
IPFIX Protocol Specification May 2005
Element and the Enterprise Number MUST be present. An example of
this is shown in section 13.4.2
The Field Specifier format is shown in Figure G.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E| Information Element ident. | Field Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure G: Field Specifier format
Where:
E
Enterprise bit. This is the first bit of the Field
Specifier. If this bit is zero, the Information Element
Identifier identifies an IETF specified Information Element,
and the four octet Enterprise Number field MUST NOT be
present. If this bit is one, the Information Element
identifier identifies an enterprise-specific Information
Element, and the Enterprise Number filed MUST be present.
Information Element identifier
A numeric value that represents the type of the Information
Element. Refer to [IPFIX-INFO].
Field Length
The length of the corresponding encoded Information Element,
in octets. Refer to [IPFIX-INFO]. The field length may be
smaller than the definition in [IPFIX-INFO] if reduced size
encoding is used (see section 6.2). The value 65535 is
reserved for variable length Information Element (see
section 7). The Field Length MAY NOT 0.
Enterprise Number
IANA enterprise number [PEN] of the authority defining the
Information Element identifier in this Template Record.
Claise, et. al Standard Track [Page 14]
IPFIX Protocol Specification May 2005
3.3 Set and Set Header Format
A Set is a generic term for a collection of records that have a
similar structure. There are three different types of Sets:
Template Sets, Options Template Sets, and Data Sets. Each of these
Sets consists of a Set Header and one or more Records. The Set
Format and the Set Header Format are defined in the following
sections.
3.3.1 Set Format
A Set has the format shown in figure H. The records types can be
either Template Records, Option Template Records or Data Records.
The record types MUST NOT be mixed within a Set.
+--------------------------------------------------+
| Set Header |
+--------------------------------------------------+
| record |
+--------------------------------------------------+
| record |
+--------------------------------------------------+
...
+--------------------------------------------------+
| record |
+--------------------------------------------------+
| Padding (opt.) |
+--------------------------------------------------+
Figure H: Set Format
The Set Field Definitions are as follows:
Set Header
The Set Header Format is defined in section 3.3.2.
Record
One of the Record Formats: Template Record or Option
Template Record or Data Record Format.
Padding
The Exporting Process MAY insert some padding octets, so that
the subsequent Set starts at an aligned boundary. Padding
Claise, et. al Standard Track [Page 15]
IPFIX Protocol Specification May 2005
MUST be composed of zero (0) octets. The padding length MUST
be shorter than any allowable record in this Set. Because
Template Sets are always 4-octet aligned by definition
padding is only needed in case of other alignments e.g. on 8-
octet boundaries.
3.3.2 Set Header Format
Every Set contains a common header. This header is defined in figure
I.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure I: Set Header Format
The Set Header Field Definitions are as follows:
Set ID
Set ID value identifies the Set. A value of 2 is reserved for
the Template Set. A value of 3 is reserved for the Option
Template Set. All other values from 4 to 255 are reserved
for future use. Values above 255 are used for Data Sets. The
Set ID values of 0 and 1 are not used for historical reasons
[RFC3954].
Length
Total length of the Set in octets including the Set Header,
all records and the optional padding. Because an individual
Set MAY contain multiple records, the Length value MUST be
used to determine the position of the next Set.
3.4 Record Format
IPFIX defines three record formats, defined in the next sections:
the Template Record Format, the Option Template Record Format and
the Data Record Format.
3.4.1 Template Record Format
Claise, et. al Standard Track [Page 16]
IPFIX Protocol Specification May 2005
One of the essential elements in the IPFIX record format is the
Template Record. Templates greatly enhance the flexibility of the
record format because they allow the Collecting Process to process
IPFIX Messages without necessarily knowing the interpretation of all
Data Records. A Template Record contains any combination of IANA-
assigned and/or enterprise-specific Information Elements
identifiers.
The format of the Template Record is shown in Figure J. It consists
of a Template Record Header and one or more Field Specifiers. The
definition of the Field Specifiers is given in figure G above.
+--------------------------------------------------+
| Template Record Header |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
Figure J: Template Record Format
The format of the Template Record Header is shown in Figure K.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID (> 255) | Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure K: Template Record Header Format
The Template Record Header Field Definitions are as follows:
Template ID
Each of the newly generated Template Records is given a unique
Template ID. This uniqueness is local to the Observation
Domain that generated the Template ID. Template IDs 0-255 are
reserved for Template Sets, Options Template Sets, and other
Claise, et. al Standard Track [Page 17]
IPFIX Protocol Specification May 2005
reserved Sets yet to be created. Template IDs of Data Sets
are numbered from 256 to 65535. There are no constraints
regarding the order of the Template ID allocation.
Field Count
Number of fields in this Template Record. Because a Template
Set usually contains multiple Template Records, this field
allows the Collecting Process to determine the end of the
current Template Record and the start of the next.
The example in Figure L shows a Template Set with mixed standard and
enterprise-specific Information Elements. It consists of Set Header,
Template Header and several Field Specifiers.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 256 | Field Count = N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 1.1 | Field Length 1.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 1.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Information Element id. 1.2 | Field Length 1.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 1.N | Field Length 1.N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 1.N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 257 | Field Count = M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Information Element id. 2.1 | Field Length 2.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 2.2 | Field Length 2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Claise, et. al Standard Track [Page 18]
IPFIX Protocol Specification May 2005
|1| Information Element id. 2.M | Field Length 2.M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 2.M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Padding (opt) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure L: Template Set Example
Information Element Identifiers 1.2 and 2.1 are defined by the IETF
(Enterprise bit = 0) and therefore do not need an Enterprise Number
to identify them.
3.4.2 Options Template Record Format
Thanks to the notion of scope, The Options Template Record gives the
Exporter the ability to provide additional information to the
Collector which would not be possible with Flow Records alone.
One Options Template Record example is the "Flow Keys", which
reports the Flow Keys for a template, which is defined as the scope.
Another example is the "Template configuration", which reports the
configuration sampling parameter(s) for the template, which is
defined as the scope.
3.4.2.1 Scope
The scope, which is only available in the Options Template Set,
gives the context of the reported Information Elements in the Data
Records. Note that the IPFIX Message Header already contains the
Source ID (the identifier of the Observation Domain). If not zero,
this Source ID can be considered as an implicit scope for the Data
Records in the IPFIX Message.
Multiple scope fields MAY be present in the Options Template Record,
in which case, the composite scope is the combination of the scopes.
For example, if the two scopes are defined as "metering process" and
"template", the combined scope is this template for this metering
process. The order of the scope fields, as defined in the Options
Template Record, is irrelevant in this case. However, if the order
of the scope fields in the Option Template Record is relevant, the
order of the scope fields MUST be used. For example, if the first
scope defines the filtering function, while the second scope defines
Claise, et. al Standard Track [Page 19]
IPFIX Protocol Specification May 2005
the sampling function, the order of the scope is important. Applying
the sampling function first, followed by the filtering function,
would lead to potentially different Data Records than applying the
filtering function first, followed by the sampling function. In
this case, the Collector deduces the function order by looking at
the order of the scope in the Options Template Record.
The scope is an Information Element specified in the IPFIX
Information Model [IPFIX-INFO]. An IPFIX compliant implementation of
the Collecting Process SHOULD support this minimum set of
Information Elements as scope: LineCardId, TemplateId,
exporterIPv4Address, exporterIPv6Address, and ingressInterface.
Note that other Information Elements such as meteringProcessId,
exportingProcessId, sourceId, etc. are also valid scopes. The IPFIX
protocol doesn't prevent the use of any Information Elements for
scope. However some Information Element types don't make sense if
specifed as scope. For example: the counter Information Elements.
Finally, note that the Scope Field Count MAY NOT be zero.
3.4.2.2 Options Template Record Format
An Option Template Record contains any combination of IANA-assigned
and/or enterprise-specific Information Elements identifiers.
The format of the Option Template Record is shown in Figure M. It
consists of a Option Template Record Header and one or more Field
Specifiers. The definition of the Field Specifiers is given in
figure G above.
+--------------------------------------------------+
| Option Template Record Header |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
Figure M: Option Template Record Format
Claise, et. al Standard Track [Page 20]
IPFIX Protocol Specification May 2005
The format of the Option Template Record Header is shown in Figure
N.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID (> 255) | Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure N: Option Template Record Header Format
The Options Template Record Header Field Definitions are as follows:
Template ID
Template ID of this Options Template Record. This value is
greater than 255.
Field Count
Number of all fields in this Option Template Record, including
the Scope Fields. Because an Option Template Set usually
contains multiple Option Template Records, this field allows
the Collecting Process to determine the end of the current
Option Template Record and the start of the next.
Scope Field Count
Number of scope fields in this Option Template Record. The
Scope Fields are normal Fields except that they are
interpreted as Scope at the Collector. The Scope Field Count
MAY NOT be zero.
The example in Figure O shows an Option Template Set with mixed IETF
and enterprise-specific Information Elements. It consists of Set
Header, Option Template Header and several Field Specifiers.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 258 | Field Count = N + M |
Claise, et. al Standard Track [Page 21]
IPFIX Protocol Specification May 2005
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = N |0| Scope 1 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length |0| Scope 2 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 2 Field Length | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |1| Scope N Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope N Field Length | Scope N Enterprise Number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Scope N Enterprise Number |1| Option 1 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option 1 Field Length | Option 1 Enterprise Number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Option 1 Enterprise Number | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |0| Option M Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option M Field Length | Padding (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure O: Option Template Set Example
3.4.3 Data Record Format
The Data Records are sent in Data Sets. The format of the Data
Record is shown in Figure P. It consists only of one or more Field
Values. The Template ID to which the Field Values belong is encoded
in the Set Header field "Set ID" i.e., "Set ID" = "Template ID".
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
Figure P: Data Record Format
Claise, et. al Standard Track [Page 22]
IPFIX Protocol Specification May 2005
Note that Field Values do not necessarily have a length of 16 bits.
Field Values are encoded according to their data type specified in
[IPFIX-INFO].
Interpretation of the Data Record format can be done only if the
Template Record corresponding to the Template ID is available at the
Collecting Process.
The example in Figure Q shows a Data Set. It consists of a Set
Header several Field Values.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = Template ID | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 1 - Field Value 1 | Record 1 - Field Value 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 1 - Field Value 3 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 2 - Field Value 1 | Record 2 - Field Value 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 2 - Field Value 3 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 3 - Field Value 1 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | Padding (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure Q: Data Set, containing Data Records
4. Specific Reporting Requirements
Some specific Options Templates and Options Templates Records are
necessary to provide extra information about the Flow Records and
about the Metering Process.
The Option Template and Option Template Records defined in these
sub-sections are not mandatory to implement as they impose some
constraints on the Metering Process implementation: this document
specifies the protocol to export the records, not the Metering
Process implementation. However, if the specific Option Templates
Claise, et. al Standard Track [Page 23]
IPFIX Protocol Specification May 2005
are implemented, they should ideally be implemented as specified in
these sub-sections.
The minimum set of Information Elements is always specified in these
Specific IPFIX Options Templates. Nevertheless, extra Information
Elements may be used in these specific Options Templates.
4.1 The Metering Process Statistics Option Template
The Metering Process Statistics Option Template specifies the
Metering Process Statistics. It contains the following Information
Elements [IPFIX-INFO]:
sourceId The Source ID. This Information
Element MUST be defined as a
Scope Field Specifier
exportedOctetCount The number of all octets reported
by the Exporting Process to the
Collecting Process
exportedPacketCount The number of all packets reported
by the exporting process to the
Collecting Process
exportedFlowCount The number of all flow records
reported by the Exporting Process
to the Collecting Process
time The time at which the record is
generated, specified by one of the
time-related Information Elements in
[IPFIX-INFO]
The Exporting Process should export the Metering Process Statistics
Option Template Record on a regular basis or based on some export
policy. This periodicity or export policy should be configurable.
The Metering Process Statistics Option Template could be extended
with other Information Elements.
Note that if several Metering Processes are available on the
Exporter Observation Domain, an extra Scope Field MeteringProcessID
must be added to this Option Template.
Claise, et. al Standard Track [Page 24]
IPFIX Protocol Specification May 2005
4.2 The Metering Process Reliability Statistics Option Template
The Metering Process Reliability Option Template specifies
information about lack of reliability in the Metering process. It
contains the following Information Elements [IPFIX-INFO]:
sourceId The Source ID. This Information
Element MUST be defined as a
Scope Field Specifier
droppedFUPacketCount Packets dropped by Metering Process
droppedFUOctetCount Octets dropped by Metering Process
timeFirstFUDropped Time of the first packet dropped
timeLastFUDropped Time of the last packet dropped
time The time at which the record is
generated, specified by one of the
time-related Information Elements in
[IPFIX-INFO].
The Exporting Process should export the Metering Process Reliability
Statistics Option Template Record on a regular basis or based on
some export policy. This periodicity or export policy should be
configurable. The Metering Process Reliability Statistics Option
Template could be extended with other Information Elements.
Note that if several Metering Processes are available on the
Exporter Observation Domain, an extra Scope Field MeteringProcessID
must be added to this Option Template.
4.3 The Exporting Process Reliability Statistics Option Template
The Exporting Process Reliability Option Template specifies
information about lack of reliability in the Exporting process. It
contains the following Information Elements [IPFIX-INFO]:
exporterID Either the exporterIPv4Address or
exporterIPv6Address [IPFIX-INFO]. This
Claise, et. al Standard Track [Page 25]
IPFIX Protocol Specification May 2005
Information Element MUST be defined
as a Scope Field Specifier
droppedFlows Number of flow records not exported
(due to resource starvation at the
Exporting Process or due to some
flow record export policies)
droppedFAPacketCount Packets in the dropped flows
droppedFAOctetCount Octets in the dropped flows
timeFirstFADropped Time of the first packet within the
dropped flows
timeLastFADropped Time of the last packet within the
dropped flows
time The time at which the record is
generated, specified by one of the
time-related Information Elements in
[IPFIX-INFO]
The Exporting Process should export the Exporting Process
Reliability Statistics Option Template Record on a regular basis or
based on some export policy. This periodicity or export policy
should be configurable. The Exporting Process Reliability Statistics
Option Template could be extended with other Information Elements.
Note that if several Exporting Processes are available on the
Exporter Observation Domain, an extra Scope Field exportingProcessID
must be added to this Option Template.
4.4 The Flow Keys Option Template
The Flow Keys Option Template specifies the Flow Keys associated
with the Template ID. It contains the following Information Elements
[IPFIX-INFO]:
templateID The Template ID. This Information
Element MUST be defined as a Scope
Field Specifier
Claise, et. al Standard Track [Page 26]
IPFIX Protocol Specification May 2005
keyList Bitmap with the positions of the flow
keys in the template
time The time at which the record is
generated, specified by one of the
time-related Information Elements in
[IPFIX-INFO]
5. IPFIX Message Header "Export Time" and Flow Record Time
The IPFIX Message Header "Export Time" field is the time in seconds
since 0000 UTC Jan 1st, 1970, at which the IPFIX Message Header
leaves the Exporter. The time-related Information Elements
specified in [IPFIX-INFO] MAY use this "Export Time" as base time
and specify an offset relative to it, instead of using a common base
time, such as 0000 UTC Jan 1st, 1970. All Information Elements that
do not have their base time defined by their data type, MUST have
the base time clearly specified in their description.
For example, Data Records requiring a microsecond precision can
export the flow start and end times with the flowStartMicroSeconds
and flowEndMicroSeconds Information Elements [IPFIX-INFO],
containing the time since 0000 UTC Jan 1st 1970. An alternate
solution is to export the flowStartDeltaUSeconds and
flowEndDeltaUSeconds Information Elements [IPFIX-INFO] in the Data
Record, which respectively report the flow start and end time
offsets compared to the IPFIX Message Header "Export Time". The
latter solution lowers the export bandwidth requirement while it
increases the load on the Exporter as the Exporting Process must
calculate the flowStartDeltaUSeconds and flowEndDeltaUSeconds of
every single Data Record before exporting the IPFIX Message.
It must be noted that using time-related Information Elements with
offset times compared to the IPFIX Message Header "Export Time"
imposes some time constraints on the Data Records contained in the
IPFIX Message. In the example of flowStartDeltaUSeconds and
flowEndDeltaUSeconds Information Elements [IPFIX-INFO], the Data
Record must be exported within a maximum of 71 minutes after its
creation. Otherwise, the 32-bits counter would not be sufficient to
contain the flow start time offset.
Claise, et. al Standard Track [Page 27]
IPFIX Protocol Specification May 2005
6. Linkage with the Information Model
The Information Elements [IPFIX-INFO] MUST be sent in canonical
format in network byte order (also known as the big-endian byte
ordering).
6.1 Encoding of IPFIX Data Types
The following sections will define the encoding of the data types
specified in [IPFIX-INFO].
6.1.1 Integral Data Types
Integral data types - octet, unsigned16, unsigned32 and unsigned64 -
are encoded using the default canonical format in network byte
order.
6.1.2 Address Types
Address types - macAddress, ipv4Address and ipv6Address - are
encoded the same way as the integral data types. The macAddress is
treated as a 6-octet integer, the ipv4Address as a 4-octet integer
and the ipv6Address as a 16-octet integer.
6.1.3 float32
The float32 data type is encoded as an IEEE single-precision 32-bit
floating point-type.
6.1.4 boolean
The boolean data type is specified according to the TruthValue in
[RFC2579]: that is an integer with the value 1 for true and a value
2 for false. Every other value is undefined. The boolean data type
is encoded in a single octet.
6.1.5 string and octetarray
The data type string represents a finite length string of valid
characters of the Unicode character encoding set. It is expected
that strings will be encoded in UTF-8 format. The string is sent as
an array of octets using an information element of fixed or variable
Claise, et. al Standard Track [Page 28]
IPFIX Protocol Specification May 2005
length. The length of the information element specifies the length
of the octetarray. In case of fixed length Information Element, if
padding is required, padding MUST be composed of NUL character(s).
6.1.6 dateTimeSeconds
The data type dateTimeSeconds represents a time value having a
precision of seconds and normalised to the GMT timezone. It is
encoded in a 32-bit integer containing the number of seconds since
0000 UTC Jan 1st 1970.
6.1.7 dateTimeMilliSeconds
The data type dateTimeMilliSeconds represents a time value having a
precision of milliseconds and normalized to the GMT timezone. It is
encoded in a 64-bit integer containing the number of milliseconds
since 0000 UTC Jan 1st 1970.
6.1.8 dateTimeNanoSeconds
The data type of dateTimeNanoSeconds represents a time value having
a precision of nanoseconds and normalized to the GMT timezone. It
is encoded in a 64-bit integer according to the NTP format given in
[RFC1305]. The high-order 32-bits represent the number of seconds
1900 and the low-order 32-bits represent the fractional seconds with
the fraction ranging from 0 - 2^(32-1) / 2^32. This gives a maximum
precision of about 200 picoseconds.
6.1.9 dateTimeMicroSeconds
The data type dateTimeMicroSeconds represents a time value having a
precision of microseconds and normalized to the GMT timezone. Its
encoding is the same as that for dateTimeNanoSeconds, but it may use
fewer bits in the fractional seconds so as to reflect its lesser
precision.
6.2 Reduced Size Encoding of Integer Types
Information Elements containing integer, string, and octetarray
types in the information model MAY be encoded using fewer octets
than those implied by their type in the information model definition
Claise, et. al Standard Track [Page 29]
IPFIX Protocol Specification May 2005
[IPFIX-INFO], based on the assumption that the smaller type is
sufficient to carry any value the Exporter may need to deliver.
This reduces the network bandwidth requirement between the Exporter
and the Collector. Note that the Information Element definitions
[IPFIX-INFO] will always define the maximum encoding size.
For instance the information model [IPFIX-INFO] defines byteCount as
an unsigned64 type, which would require 64-bits. However if the
Exporter will never locally encounter the need to send a value
larger than 4294967295, it may chose to send the value instead as an
unsigned32. For example, a core router would require an unsigned64
byteCount while an unsigned32 might be sufficient for an access
router.
This behavior is indicated by the Exporter by specifying a type size
with a smaller length than that associated with the assigned type of
the Information Element. In the example above the Exporter would
place a length of 4 versus 8 in the template.
If reduced sizing is used, it MUST be applied only to following
integer types: unsignedLong, long, unsignedInt, int, unsignedShort,
short. In each case the downcasting MUST be to a smaller integer
type. The same signed versus unsigned properties MUST be preserved.
Specifically unsignedLong may be downcast to unsignedInt,
unsignedShort or unsignedByte. A long may be downcast to an int, a
short or a byte. The other downcasts follow the same pattern.
7. Variable Length Information Element
The IPFIX template mechanism is optimized for fixed length
Information Elements [IPFIX-INFO]. Where an Information Element has
a variable length the following mechanism MUST used to carry the
length information, for both the IETF and proprietary Information
Elements.
In the Template Set the length is recorded as 65535. This reserved
length value notifies the Collecting Process that length of the
Information Element will be carried in the Information Element
content itself.
In most cases the length of the Information Element will be less
than 255 octets. The following length encoding mechanism optimizes
Claise, et. al Standard Track [Page 30]
IPFIX Protocol Specification May 2005
the overhead of carrying the Information Element length in this
majority case.
If the length of the Information Element is less than 255 octets,
the length is carried in the first octet of the Information Element,
as shown in Figure R.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length (< 255)| Information element |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... continuing as needed |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure R: Variable Length Information Element (length < 255 octets)
If the length of the Information Element is greater than or equal to
255 octets, the first octet of the Information Element is 255, and
the length is carried in the second and third octets of the
Information Element, as shown in Figure S.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 255 | Length (255 to 65535) | IE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... continuing as needed |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure S: Variable Length Information Element
(length 255 to 65535) octets
8. Template Management
This section describes Template management when using SCTP and SCTP-
PR as the transport protocol. Any necessary changes to Template
management specifically related to TCP or UDP transport protocols
are specified in section 10.
The Exporting Process assigns and maintains the Template IDs for the
Exporter's Observation Domains. A newly created Template Record is
assigned an unused Template ID by the Exporting Process.
Claise, et. al Standard Track [Page 31]
IPFIX Protocol Specification May 2005
Template Sets and Option Template Sets MUST be only sent once on
SCTP stream zero with full reliability. As such, the Collecting
Process MUST store the Template Record information for the duration
of the association so that it can interpret the corresponding Data
Records that are received in subsequent Data Sets.
New Template Records SHOULD be transmitted as soon as they are
created. The Exporting Process MAY transmit the Template Set and
Options Template Set in advance of any Data Sets that use that
(Options) Template ID, to ensure that the Collector has the Template
Record before receiving the first Data Record. Data Records that
correspond to a Template Record MAY appear in the same and/or
subsequent IPFIX Message(s).
A Template ID MUST be unique per Observation Domain. Different
Observation Domains from the same Exporter may use the same Template
ID value to refer to different Templates.
Disused Templates SHOULD be deleted. Before reusing a Template ID
the disused Template MUST be deleted. In order to delete an
allocated Template, the Template is withdrawn through the use of a
Template Withdraw Message.
The Template Withdraw Message MUST not be sent until sufficient time
has elapsed to allow the Collecting Process to receive and process
the last Data Record using this Template information. This time MUST
be configurable.
The Template ID from a withdrawn Template MUST NOT be reused until
sufficient time has elapsed to allow for the Collecting Process to
receive and process the Template withdraw message.
A Template Withdraw Message is a Template Record for that Template
ID with a Field Count of 0. The format of the Template Withdrawal
Message is shown in figure T.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = (2 or 3) | Length = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Claise, et. al Standard Track [Page 32]
IPFIX Protocol Specification May 2005
| Template ID N | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID ... | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID M | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure T: Template Withdrawal Message format
The Set ID field MUST contain the value 2 for Template Set
withdrawal and the value 3 for Options Template Set withdrawal.
Multiple Template IDs MAY be withdrawn with a single Template
Withdrawal Message: in that case, padding MAY be used.
The Template Withdraw Message withdraws the Template IDs for the
Source ID specified in the IPFIX Message header.
If the measurement parameters change, the Template MUST be withdrawn
(using a Template Withdraw Message and a new Template definition) or
an unused Template ID MUST be used. Examples of the measurement
changes are: a new sampling rate, a new flow expiration process, a
new filtering definition, etc. If a Template is changed, a Template
Withdraw Message MUST be sent to delete the Template.
When the Exporting Process restarts, due to the SCTP association
shutdown, all Template assignments are lost and Template IDs MUST be
re-assigned.
If the Metering Process restarts, the Exporting Process MUST either
reuse the previously assigned Template ID for each Template, or it
MUST withdraw the previously issued Template IDs by sending Template
Withdraw Message(s) before reusing them.
A Template Withdrawal Message to withdraw all Data Templates for the
Source ID specified in the IPFIX message header MAY be used. Its
format is shown in figure U.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 8 |
Claise, et. al Standard Track [Page 33]
IPFIX Protocol Specification May 2005
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 2 | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure U: All Data Templates Withdrawal Message format
A Template Withdrawal Message to withdraw all Options Templates for
the Source ID specified in the IPFIX message header MAY be used. Its
format is shown in figure V.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 3 | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure V: All Options Templates Withdrawal Message format
When the SCTP association restarts, the Exporting Process MUST
resend all the Template Records.
9. The Collecting Process's Side
This section describes the Collecting Process when using SCTP and
SCTP-PR as the transport protocol. Any necessary changes to the
Collecting Process specifically related to TCP or UDP transport
protocols are specified in section 10.
The Collecting Process SHOULD listen for a new association request
from the Exporting Process. The Exporting Process will request a
number of streams to use for export. A Collecting Process MUST
support at least two inbound streams per association. An Exporting
Process MAY ask for and support more than two streams.
If the Collecting Process receives a malformed IPFIX Message, it
MUST reset the SCTP association, discard the IPFIX Message, and
SHOULD log the error.
Template Sets and Option Template Sets are only sent once. The
Collecting Process MUST store the Template Record information for
the duration of the association so that it can interpret the
Claise, et. al Standard Track [Page 34]
IPFIX Protocol Specification May 2005
corresponding Data Records that are received in subsequent Data
Sets.
Template IDs are unique per Exporting Process and per Observation
Domain. If the Collecting Process receives a Template which has
already been received but which has not previously been withdrawn
(i.e. a Template Record from the same Exporter Observation Domain
with the same Template ID), then the Collecting Process MUST
shutdown the association.
When an SCTP association is closed, the Collecting Process MUST
discard all templates received over that association and stop
decoding IPFIX Messages that use those templates.
The Collecting Process normally receives Template Records from the
Exporting Process before receiving Data Records. The Data Records
are then decoded and stored by the Collector. If the Template
Records have not been received at the time Data Records are
received, the Collecting Process MAY store the Data Records for a
short period of time and decode them after the Template Records are
received. A Collecting Process MUST NOT assume that the Data Set
and the associated Template Set (or Options Template Set) are
exported in the same IPFIX Message.
The Collecting Process MUST note the Information Element identifier
of any Information Element that it does not understand and MAY
discard that Information Element from the Flow Record.
The Collector MUST accept padding in Data Records and Template
Records.
The IPFIX protocol has a Sequence Number field in the Export header
which increases with the number of IPFIX Data Records in the IPFIX
Message. A Collector may detect out of sequence, dropped, or
duplicate IPFIX Messages by tracking the Sequence Number. A
collector SHOULD provide a logging mechanism for tracking out of
sequence IPFIX Messages. Such out of sequence IPFIX Messages may be
due to Exporter resource exhaustion where it can not transmit
messages at their creation rate, an Exporting Process reset,
congestion on the network link between the Exporter and Collector,
Collector resource exhaustion where it can not process the IPFIX
Messages at their arrival rate, out of order packet reception,
duplicate packet reception, or an attacker injecting false messages.
Claise, et. al Standard Track [Page 35]
IPFIX Protocol Specification May 2005
If a Collecting Process receives a Template Withdraw Message, the
Collecting Process MUST delete the corresponding Template Records
associated with the specific Exporter and specific Observation
Domain, and stop decoding IPFIX Messages that use the withdrawn
Templates.
A Collecting Process that receives IPFIX Messages from several
Observation Domains from the same Exporter MUST be aware that the
uniqueness of the Template ID is not guaranteed across Observation
Domains.
10. Transport Protocol
The IPFIX Protocol Specification has been designed to be transport
protocol independent. Note that the Exporter can export to multiple
Collecting Processes, using independent transport protocols.
The IPFIX Message Header 16-bit Length field limits the length of a
IPFIX Message to 65535 octets including the header. A Collecting
Process MUST be able to handle IPFIX Message lengths of up to 65535
octets.
10.1 Transport Compliance and Transport Usage
We need to differentiate between what must be implemented (so that
operators can interoperably deploy compliant implementations from
different vendors) and what should or could be used in various
operational environments. We must also make sure that ALL
implementations can operate in a congestion-aware and congestion
avoidance mode.
SCTP [RFC2960] and SCTP-PR [RFC3758] MUST be implemented by all
compliant implementations. UDP [UDP] MAY also be implemented by
compliant implementations. TCP [TCP] MAY also be implemented by
compliant implementations.
SCTP-PR SHOULD be used in deployments where Exporters and Collectors
are communicating over links that are susceptible to congestion.
SCTP-PR is capable of providing any required degree of reliability.
TCP MAY be used in deployments where Exporters and Collectors
communicate over links that are susceptible to congestion, but SCTP-
Claise, et. al Standard Track [Page 36]
IPFIX Protocol Specification May 2005
PR is preferred, due to its ability to limit back pressure on
Exporters and its message versus stream orientation.
UDP MAY be used although it is not a congestion aware protocol.
However, the IPFIX traffic between Exporter and Collector MUST
remain wholly within the administrative domains of the operators.
10.2 SCTP
This section describes how IPFIX can be transported over SCTP
[RFC2960] using the PR-SCTP [RFC3758] extension.
10.2.1 Congestion Avoidance
The SCTP transport protocol provides the required level of
congestion avoidance by design.
SCTP will detect congestion in the end-to-end path between
the IPFIX Exporting Process and the IPFIX Collecting Process,
and limit the transfer rate accordingly. When an IPFIX
Exporting Process has records to export, but detects that
transmission by SCTP is temporarily impossible, it can either
wait until sending is possible again, or it can decide to drop the
record. In the latter case, the dropped export data MUST
be accounted for, so that the amount of dropped export data can be
reported.
10.2.2 Reliability
The SCTP transport protocol is by default reliable, but has the
capability to operate in unreliable and partially reliable modes
[RFC3758].
Using reliable SCTP streams (referred to hereafter as "streams") for
the IPFIX export is not in itself a guarantee that all Data Records
are delivered. If there is congestion on the link from the
Exporting Process to the Collecting Process, or if a significant
number of retransmissions are required, the send queues on the
Exporting Process may fill up: the Exporting Process MAY either
suspend export or discard the IPFIX Messages. If Data Records are
discarded the sequence numbers used for export MUST reflect the loss
of data.
Claise, et. al Standard Track [Page 37]
IPFIX Protocol Specification May 2005
10.2.3 MTU
SCTP provides the required IPFIX Message fragmentation service based
on path MTU discovery.
10.2.4 Exporting Process
10.2.4.1 Association Establishment
The IPFIX Exporting Process SHOULD initiate an SCTP association with
the IPFIX Collecting Process. By default, the Collecting Process
listens for connections on SCTP port XXXX (EDITOR NOTE: to be
assigned by IANA). By default the Exporting Process tries to
connect to this port. It MUST be possible to configure both the
Exporting and Collecting Processes to use a different SCTP port.
The Exporting Process MAY establish more than one associations
(connection "bundle" in SCTP terminology) to the Collecting Process.
An Exporting Process MAY support more than one active association
to different Collecting Processes (including the case of different
Collecting Processes on the same host).
10.2.4.2 Association Shutdown
When an Exporting Process is shutdown, it SHOULD shutdown the SCTP
association.
When a Collecting Process no longer wants to receive IPFIX
Messages, it SHOULD shutdown its end of the association. The
Collecting Process SHOULD continue to receive and process
IPFIX Messages until the Exporting Process has closed its end of the
association.
When a Collecting Process detects that the SCTP association has been
abnormally terminated, it MUST continue to listen for a new
association establishment.
When an Exporting Process detects that the SCTP association to the
Collecting Process is abnormally terminated, it SHOULD try to re-
establish the association.
Claise, et. al Standard Track [Page 38]
IPFIX Protocol Specification May 2005
Association timeouts SHOULD be configurable.
10.2.4.3 Stream
An Exporting Process MUST request at least two outbound streams per
association. The first stream (referred to as stream zero in the
rest of this document), is used to send the Template Set and the
Options Template Set. Stream zero MUST be fully reliable. Data
Sets MUST NOT be sent on stream zero.
Depending on the application requirement, the Exporting Process
selects the mode (unreliable, partially reliable, or fully reliable)
of the stream, used to send the Data Sets. Unreliable mode MAY be
used where the application does not require reliable transmission
and the use of a retransmission queue is impractical.
An Exporter MAY use multiple streams to export Data Sets, in some
cases different applications will have different requirements in
terms of reliability. In such a case, the Observation Domain MUST
use the same Source ID value on all of the multiple streams it uses.
Data Sets from multiple Observation Domains MUST NOT be transmitted
over the same stream; the Collecting Process should however verify
that the Source ID values are the expected values.
When Data Sets are exported over a partially reliable stream, they
SHOULD be marked for retransmission as long as there is room in the
SCTP send queues. However, if the queue overflows during times of
congestion or other retransmission events, the oldest Data Record
that has been transmitted and marked as partially reliable should be
freed and marked to be skipped per the PR-SCTP [RFC3758]
specification. The freed buffer space should then be re-used for
the new Data Sets being exported.
10.2.4.4 Template Management
When the transport protocol is SCTP the default Template Management
described in Section 8 is used.
10.2.5 Collecting Process
Claise, et. al Standard Track [Page 39]
IPFIX Protocol Specification May 2005
When the transport protocol is SCTP, the default Collector
processing described in Section 9 is used.
10.2.6 Failover
If the Collecting Process does not acknowledge the attempt by the
Exporting Process to establish an association the Exporting Process
should retry using the SCTP exponential backoff feature. The
Exporter MAY log an alarm if the time to establish the association
exceeds a specified threshold.
If Collecting Process failover is supported by the Exporting Process
a second SCTP association MAY be opened in advance.
10.3 UDP
This section describes how IPFIX can be transported over UDP
[RFC768]
10.3.1 Congestion Avoidance
UDP has no integral congestion avoidance mechanism. Its use
over congestion sensitive network paths is therefore deprecated.
UDP MAY be used in deployments where Exporters and Collectors
always communicate over dedicated links that are not susceptible
to congestion.
10.3.2 Reliability
UDP is not a reliable transport protocol, and cannot guarantee
delivery of messages. IPFIX Messages sent from the Exporting
Process to the Collecting Process using UDP may therefore be lost.
UDP MUST NOT be used unless the application can tolerate some
loss of IPFIX Messages.
The Collecting Process could deduce the loss and reordering of IPFIX
Data Records by looking at the discontinuities in the IPFIX Message
sequence number. In the case of UDP, the IPFIX Message sequence
number contains the total number of IPFIX Data Records received for
the UDP association, prior to the receipt of this IPFIX Message,
modulo 2^32. IPFIX sequence number discontinuities SHOULD be logged.
Claise, et. al Standard Track [Page 40]
IPFIX Protocol Specification May 2005
Templates sent from the Exporting Process to the Collecting
Process using UDP as a transport MUST be resent at regular
intervals in case previous copies were lost. Implementations
MAY send templates using a reliable transport protocol, and
send IPFIX Data Records using UDP as the transport protocol.
10.3.3 MTU
The maximum size of exported messages MUST be configured such that
the total packet size does not exceed the path MTU.
10.3.4 Port Numbers
By default, the Collecting Process listens on the UDP port XXXX
(EDITOR NOTE: to be assigned by IANA). By default the Exporting
Process tries to connect to this port. It MUST be possible to
configure both the Exporting and Collecting Processes to use a
different UDP port.
10.3.5 Exporting Process
The Exporting Process MAY duplicate the IPFIX Message to the several
Collecting Processes.
10.3.6 Template Management
When IPFIX uses UDP as the transport protocol, Template Sets and
Option Template Sets MUST be re-sent at regular intervals. The
frequency of (Options) Template transmission MUST be configurable.
New Template Records SHOULD be transmitted as soon as they are
created, and SHOULD be transmitted before any associated Data Record
is transmitted.
In the event of configuration changes, the Exporting Process SHOULD
send multiple copies of the new template definitions, in different
IPFIX Messages, at an accelerated rate. In such a case, it MAY
transmit the changed Template Record(s) and Options Template
Record(s), without any data, in advance to help ensure that the
Collector will have the correct template information before
receiving the first data.
Claise, et. al Standard Track [Page 41]
IPFIX Protocol Specification May 2005
If the Option Template scope is defined in another Template, then
both Templates SHOULD be sent in the same IPFIX Message. For
example: if a Flow Key Option Template (see section 4.4) is sent in
an Option Template, then the associated Template SHOULD be sent in
the same IPFIX Message.
Following a configuration change that can modify the interpretation
of the Data Records (for example, a sampling rate change) a new
Template ID MUST be used and the old Template ID MUST NOT be reused
until its lifetime (see section 10.3.7) has expired.
Template Withdraw Messages SHOULD NOT be sent over UDP.
10.3.7 Collecting Process
The Collecting Process MUST associate a lifetime with each Template
received via UDP. Templates not refreshed by the Exporting Process
within the lifetime are expired at the Collecting Process. If the
template is not refreshed by the Exporting Process before that
lifetime has expired, the Collecting Process MUST discard the
Template and any current and future associated Data Records. In
which case, an alarm MUST be logged. The Collecting Process MUST
NOT decode any further Data Records which are associated with the
expired Template. The Template lifetime at the Collecting Process
MUST be at least 3 times higher that the Template refresh timeout
configured on the Exporting Process.
At any given time the Collecting Process SHOULD maintain the
following for all the current Template Records and Options Template
Records: <Exporting Process, Observation Domain Source ID, Template
ID, Template Definition, Last Received>.
The Collecting Process SHOULD accept Data Records without the
associated Template Record. If the Template Records have not been
received at the time Data Records are received, the Collecting
Process SHOULD store the Data Records for a short period of time and
decode them after the Template Records are received. The short
period of time MUST be lower than the Template lifetime.
Claise, et. al Standard Track [Page 42]
IPFIX Protocol Specification May 2005
10.3.8 Failover
Because UDP is not a connection oriented protocol, the Exporting
Process is unable to determine from the transport protocol that the
Collecting Process is no longer able to receive the IFPIX Messages.
Therefore, it can not invoke a failover mechanism. However, the
Exporting Process MAY duplicate the IPFIX Message to several
Collecting Processes.
10.4 TCP
This section describes how IPFIX can be transported over TCP [TCP].
10.4.1 Connection Management
10.4.1.1 Connection Establishment
The IPFIX Exporting Process initiates a TCP connection to the
Collecting Process. By default, the Collecting Process listens for
connections on TCP port XXXX (EDITOR NOTE: to be assigned by IANA).
By default the Exporting Process tries to connect to this port. It
MUST be possible to configure both the Exporting Process and the
Collecting Process to use a different TCP port.
An Exporting Process MAY support more than one active connection to
different Collecting Processes (including the case of different
Collecting Processes on the same host).
The Exporter MAY log an alarm if the time to establish the
connection exceeds a specified threshold.
10.4.1.2 Graceful Connection Release
When an Exporting Process is shutdown, it SHOULD shutdown the TCP
connection. If TLS [TLS] is used, the Exporting Process SHOULD send
a close_notify alert before closing the TCP connection.
When a Collecting Process no longer wants to receive IPFIX messages,
it SHOULD close its end of the connection. The Collecting Process
SHOULD continue to read IPFIX Messages until the Exporting Process
has closed its end.
Claise, et. al Standard Track [Page 43]
IPFIX Protocol Specification May 2005
10.4.1.3 Restarting Interrupted Connections
When a Collecting Process detects that the TCP connection to the
Exporting Process has terminated abnormally, it MUST continue to
listen for a new connection.
When an Exporting Process detects that the TCP connection to the
Collecting Process has terminated abnormally, it SHOULD try to re-
establish the connection. Connection timeouts and retry schedules
SHOULD be configurable. In the default configuration, an Exporting
Process MUST NOT attempt to establish a connection more frequently
than once per minute.
10.4.1.4 Failover
If the Collecting Process does not acknowledge the attempt by the
Exporting Process to establish an connection it will retry using the
TCP exponential backoff feature.
If Collecting Process failover is supported by the Exporting Process
a second TCP connection MAY be opened in advance.
10.4.2 Data Transmission
Once a TCP connection is established, and, if configured, TLS [TLS]
usage has been negotiated, the Exporting Process starts sending
IPFIX Messages to the Collecting Process.
10.4.2.1 IPFIX Message Encoding
IPFIX Messages are sent over the TCP connection without any special
encoding. The Length field in the IPFIX Message header defines the
end of each IPFIX Message and thus the start of the next IPFIX
Message. This means that IPFIX Messages cannot be interleaved.
In the case of TCP, the IPFIX Message sequence number contains the
total number of IPFIX Data Records received for the TCP connection,
prior to the receipt of this IPFIX Message, modulo 2^32.
If an Exporting Process exports data from multiple Observation
Domains, it should be careful to choose IPFIX Message lengths
appropriately to minimize head-of-line blocking between different
Claise, et. al Standard Track [Page 44]
IPFIX Protocol Specification May 2005
Observation Domains. Multiple TCP connections MAY be used to avoid
head-of-line between different Observation Domains.
10.4.2.2 Templates
For each template, the Exporting Process MUST send the Template
Record before exporting Data Records that refer to that template.
A Collecting Process MUST record all Template and Option Template
Records for the duration of the connection, as an Exporting Process
is not required to re-export Template Records.
When the TCP connection restarts, the Exporting Process MUST resend
all the Template Records.
When an TCP connection is closed, the Collecting Process MUST
discard all templates received over that connection and stop
decoding IPFIX Messages that use those templates.
10.4.2.3 Congestion Handling and Reliability
TCP ensures reliable delivery of data from the Exporting Process to
the Collecting Process. TCP also controls the rate at which data
can be sent from the Exporting Process to the Collecting Process,
using a mechanism that takes into account both congestion in the
network and the capabilities of the receiver.
Therefore an IPFIX Exporting Process may not be able to send IPFIX
Messages at the rate that the Metering Process generates it, either
because of congestion in the network or because the Collecting
Process cannot handle IPFIX Messages fast enough. As long as
congestion is transient, the Exporting Process can buffer IPFIX
Messages for transmission. But such buffering is necessarily
limited, both because of resource limitations and because of
timeliness requirements, so ongoing and/or severe congestion may
lead to a situation where the Exporting Process is blocked.
When an Exporting Process has Data Records to export but the
transmission buffer is full, and it wants to avoid blocking, it can
decide to drop some Data Records. The dropped Data Records MUST be
accounted for, so that the amount can later be exported.
Claise, et. al Standard Track [Page 45]
IPFIX Protocol Specification May 2005
When an Exporting Process finds that the rate at which records
should be exported is consistently higher than the rate at which TCP
sending permits, it should provide back pressure to the metering
processes. The metering process could then adapt by temporarily
reducing the amount of data it generates, for example using sampling
or aggregation.
11. Security Considerations
Because IPFIX can be used to collect billing information and network
forensics, confusing or blinding IPFIX must be seen as a prime
objective during a sophisticated network attack.
If an attacker is in a position to inject false messages into an
IPFIX Message stream, this will allow them to send forged Data
Records or Template Records. Forged Templates may impair the
Collectors ability to process any further Flow Records. Forged Flow
Records would have a direct effect on the application using the
Flows, for example a billing system may generate incorrect billing
information. Forged options may be able to alter the meaning of
Flow Records, for example if the sample rate is changed.
The IPFIX Messages themselves may contain information of value to an
attacker, and thus care must be taken to confine their visibility to
authorized users.
IPFIX Messages can be secured using IPsec. Alternatively if IPFIX
runs on top of SCTP or TCP, TLS [TLS] can be used.
When an Information Element containing end-user payload information
is exported, it SHOULD be transmitted to the Collecting Process
using a means that secures its contents against eavesdropping.
Suitable mechanisms include the use of either a direct point-to-
point connection or the use of an encryption mechanism. It is the
responsibility of the Collecting Process to provide a satisfactory
degree of security for this collected data, including, if necessary,
anonymization of any reported data.
11.1 IPsec Usage
To secure messages between the Exporter and the Collector an IPFIX
implementation MAY use IPsec. To ensure interworking between
Claise, et. al Standard Track [Page 46]
IPFIX Protocol Specification May 2005
Exporters and Collectors from different vendors, the following IPsec
profile MUST be supported. This profile is derived from [USEIPSEC].
11.1.1 Selectors
IPFIX runs between manually configured pairs of hosts on the
following transport ports (EDITOR NOTE: to be assigned by IANA).
The appropriate selector would be Exporter-Collector pairs and port
number.
Note that, if the Exporter is a router, a non-interface ("loopback")
address should be used.
11.1.2 Mode
IPsec MUST be run in transport mode. The AH and ESP MUST be
supported by an IPFIX implementation of IPsec.
The Authentication Header (AH) [RFC2402] MUST be used if
authentication is required. The Security Protocol (ESP) [RFC2406]
must be used if there is a threat to the IPFIX Message content, or
if that content is confidential.
Normally in situations where the ESP was required the AH would also
be required. If only ESP is used, the sender's IP address MUST be
checked against the IP address asserted in the key management
exchange.
11.1.3 Key Management
In many networks, manual key management will be sufficient, and this
reduces the complexity of the Exporter, albeit at a cost of greater
configuration complexity. Manual key management MUST be supported.
If a replay attack is considered likely, an automated key management
such as the IKE [IKE] key management system SHOULD be used.
11.1.4 Security Policy
Connections should be accepted only from designated peers.
11.1.5 Authentication
Claise, et. al Standard Track [Page 47]
IPFIX Protocol Specification May 2005
Given the number of IPFIX capable Exporters that are likely to be
deployed by large ISPs, there will be circumstances where shared key
mechanisms are not adequate. Where an automated key management
system is used, certificate-based IKE SHOULD be supported.
11.1.6 Availability
It is accepted that IPsec will not be universally available in IPFIX
Exporters, and that where it is available, there may be issues of
throughput, which may itself raise security issues. In such
circumstances the other security measures described in this document
provide some threat mitigation.
11.2 TLS Usage
The IPFIX Exporter initiating a connection acts as a TLS client
according to [TLS], and an IPFIX Collector that accepts a connection
acts as a TLS server. If mutual authentication is required the
Collector MUST request a certificate from the Exporter, and the
Exporter MUST be prepared to supply a certificate on request.
11.3 Protection against DoS attacks
An attacker may directly mount a DoS attack by generating large
amounts of traffic. If TCP is used for transport, then the Flow to
the Collector would back off due to congestion and eventually stall,
blinding the IPFIX system. An attack could then proceed without
further observation. SCTP-PR will have a different pathology under
such an attack. Stale data at the head of the queue will get
flushed giving some visibility of the attack. In case of UDP, IPFIX
would reduce to some sort of sampling, meaning that some forensics
may be left.
To avoid blinding of the IPFIX system some mechanism for service
differentiation can be used to prioritize IPFIX traffic over user
traffic. An alternative is to use a dedicated network for the
transport of IPFIX Messages. By sending the IPFIX Messages over a
dedicated network, IPFIX Message loss induced by user traffic
congestion is minimized. However an attacker may trigger the
generation of excessive IPFIX Messages, and to avoid information
loss during such an attack the IPFIX network must be adequately
sized.
Claise, et. al Standard Track [Page 48]
IPFIX Protocol Specification May 2005
11.4 When IPsec or TLS is not an option
The use of IPsec or TLS might not be possible in certain cases due
to performance issues.
Without IPsec or TLS the only way that an IPFIX Exporter, proxy or
Collector can authenticate each other is by inspecting the IP source
address of the packets carrying the IPFIX Messages and their
transport acknowledgments. Useful protection is gained by
allocating Exporter and Collector IP addresses from ranges that are
excluded from use by user traffic and hence preventing spoofing
attacks by ingress packet filtering. Where large numbers of
Exporters, proxies and Collectors are used in a network, it may be
tempting for the administrator to not impose source IP address
restrictions but this leaves a proxy or Collector open to the
reception of invalid information. The use of an open proxy or
Collector is therefore discouraged.
If IP address spoofing can not be prevented, some level of
protection against an insertion attack is required. With a modern
implementation of TCP with good ISN randomization [RFC1948] or SCTP
insertion such attacks are difficult without the ability to snoop
the packet Flow [RFC2960]. UDP is vulnerable to insertion attacks,
and SHOULD be protected by the use of the address restriction
mechanism described above.
The use of a dedicated network prevents IPFIX Messages from being
inspected by an attacker.
11.5 Logging an IPFIX Attack
A Collector may detect problems by tracking the IPFIX Sequence
Number and therefore SHOULD provide a logging mechanism for tracking
out of sequence messages. Such out of sequence messages may not
only be caused by network congestion or Exporter/Collector resource
exhaustion but also by an attacker injecting false messages.
Note that an attacker may be able to exploit the behavior of the
Collector when it receives an out of sequence message. For example
a Collector that simply resets the expected Sequence Number upon
receipt of a later message would easily be temporarily blinded by
deliberately injecting messages with a much larger Sequence Number.
Claise, et. al Standard Track [Page 49]
IPFIX Protocol Specification May 2005
12. IANA Considerations
The IPFIX Protocol, as set out in this document, has two sets of
assigned numbers. Considerations for assigning them are discussed
in this section, using the example policies as set out in the
"Guidelines for IANA Considerations" document IANA-RFC [RFC2434].
12.1 Numbers used in the Protocol
IPFIX Messages use two fields with assigned values. These are the
IPFIX Version Number, indicating which version of the IPFIX Protocol
was used to export an IPFIX Message, and the IPFIX Set ID,
indicating the type for each set of information within an IPFIX
Message.
Changes in either IPFIX Version Number or IPFIX Set ID assignments
require an IETF Consensus, i.e. they are to be made via RFCs
approved by the IESG.
12.2 Numbers used in the Information Model
Fields of the IPFIX protocol carry information about traffic
measurement. They are modeled as elements of the IPFIX information
model [IPFIX-INFO]. Each Information Element describes a field which
may appear in an IPFIX Message. Within an IPFIX Message the
Information Element type is indicated by its Information Element
identifier.
New assignments for IPFIX Information Elements will be administered
by IANA, on a First Come First Served basis [RFC 2434] , subject to
Expert Review [RFC 2434], i.e. review by one of a group of experts
designated by an IETF Operations and Management Area Director. The
group of experts must double check the Information Elements
definitions with already defined Information Elements for
completeness, accuracy and redundancy. Those experts will initially
be drawn from the Working Group Chairs and document editors of the
IPFIX and PSAMP Working Groups. The IANA assignments for IPFIX
Information Elements will range from 128 to 32767; the values below
128 are reserved or already assigned.
13. Examples
Let's consider the example of an IPFIX Message composed of a
Claise, et. al Standard Track [Page 50]
IPFIX Protocol Specification May 2005
Template Set, a Data Set (which contains three Data Records), an
Options Template Set and a Data Set (which contains 2 Data Records
related to the previous Options Template Record).
IPFIX Message:
+--------+------------------------------------------. . .
| | +--------------+ +------------------+
|Message | | Template | | Data |
| Header | | Set | | Set | . . .
| | | (1 Template) | | (3 Data Records) |
| | +--------------+ +------------------+
+--------+------------------------------------------. . .
. . .-------------------------------------------+
+------------------+ +------------------+ |
| Options | | Data | |
. . . | Template Set | | Set | |
| (1 Template) | | (2 Data Records) | |
+------------------+ +------------------+ |
. . .-------------------------------------------+
13.1 Message Header Example
The Message Header is composed of:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version = 0x000a | Length = 152 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Export Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.2 Template Set Examples
13.2.1 Template Set using IETF specified Information Elements
We want to report the following Information Elements:
Claise, et. al Standard Track [Page 51]
IPFIX Protocol Specification May 2005
- The IPv4 source IP address: sourceIPv4Address in [IPFIX-INFO],
with a length of 4 octets
- The IPv4 destination IP address: destinationIPv4Address in [IPFIX-
INFO], with a length of 4 octets
- The next-hop IP address (IPv4): ipNextHopIPv4Address in [IPFIX-
INFO], with a length of 4 octets
- The number of packets of the Flow: inPacketDeltaCount in [IPFIX-
INFO], with a length of 4 octets
- The number of octets of the Flow: inOctetDeltaCount in [IPFIX-
INFO], with a length of 4 octets
Therefore, the Template Set will be composed of the following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 28 octets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 256 | Field Count = 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceIPv4Address = 8 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationIPv4Address = 12 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| ipNextHopIPv4Address = 15 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| inPacketDeltaCount = 2 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| inOctetDeltaCount = 1 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.2.2 Template Set using Enterprise Specific Information Elements
We want to report the following Information Elements:
- The IPv4 source IP address: sourceIPv4Address in [IPFIX-INFO],
with a length of 4 octets
Claise, et. al Standard Track [Page 52]
IPFIX Protocol Specification May 2005
- The IPv4 destination IP address: destinationIPv4Address in
[IPFIX-INFO], with a length of 4 octets
- An enterprise-specific Information Element representing
proprietary information, with a type of 15 and a length of 4
- The number of packets of the Flow: inPacketDeltaCount in
[IPFIX-INFO], with a length of 4 octets
- The number of octets of the Flow: inOctetDeltaCount in
[IPFIX-INFO], with a length of 4 octets
Therefore, the Template Set will be composed of the following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 32 octets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 257 | Field Count = 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceIPv4Address = 8 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationIPv4Address = 12 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element Id. = 15| Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| inPacketDeltaCount = 2 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| inOctetDeltaCount = 1 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.3 Data Set Example
In this example, we report the following three Flow Records:
Src IP addr. | Dst IP addr. | Next Hop addr. | Packet | Octets
| | | Number | Number
------------------------------------------------------------------
198.18.1.12 | 198.18.2.254 | 198.18.1.1 | 5009 | 5344385
Claise, et. al Standard Track [Page 53]
IPFIX Protocol Specification May 2005
198.18.1.27 | 198.18.2.23 | 198.18.1.2 | 748 | 388934
198.18.1.56 | 198.18.2.65 | 198.18.1.3 | 5 | 6534
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 256 | Length = 64 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.2.254 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5009 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5344385 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.27 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.2.23 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 748 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 388934 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.56 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.2.65 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 198.18.1.3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 6534 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Note that padding is not necessary in this example.
Claise, et. al Standard Track [Page 54]
IPFIX Protocol Specification May 2005
13.4 Options Template Set Examples
13.4.1 Options Template Set using IETF specified Information Elements
Per line card (the router being composed of two line cards), we want
to report the following Information Elements:
- Total number of IPFIX Messages: exportedPacketCount
[IPFIX-INFO], with a length of 2 octets
- Total number of exported Flows: exportedFlowCount [IPFIX-INFO],
with a length of 2 octets
The line card, which is represented by the lineCardId Information
Element [IPFIX-INFO], is used as the Scope Field.
Therefore, the Options Template Set will be:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 24 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 258 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |0| lineCardId = 141 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 |0| exportedPacketCount = 41 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0| exportedFlowCount = 42 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.4.2 Options Template Set using enterprise-specific Information
Elements
Per line card (the router being composed of two line cards), we want
to report the following Information Elements:
- Total number of IPFIX Messages: exportedPacketCount
[IPFIX-INFO], with a length of 2 octets
Claise, et. al Standard Track [Page 55]
IPFIX Protocol Specification May 2005
- An enterprise-specific number of exported Flows,
with a type of 42 and a length of 4 octets
The line card, which is represented by the lineCardId Information
Element [IPFIX-INFO], is used as the Scope Field.
The format of the Options Template Set is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 259 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |0| lineCardId = 141 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 |0| exportedPacketCount = 41 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |1|Information Element Id. = 42 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 4 | Enterprise number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Enterprise number | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.4.3 Options Template Set using an enterprise-specific scope
In this example, we want to export the same information as in the
example in section 13.4.1:
- Total number of IPFIX Messages: exportedPacketCount
[IPFIX-INFO], with a length of 2 octets
- Total number of exported Flows: exportedFlowCount
[IPFIX-INFO], with a length of 2 octets
But this time, the information pertains to a proprietary scope,
identified by enterprise-specific Information Element number 123.
The format of the Options Template Set is now as follows:
Claise, et. al Standard Track [Page 56]
IPFIX Protocol Specification May 2005
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 260 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |1|Scope 1 Infor. El. Id. = 123 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 |0| exportedPacketCount = 41 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0| exportedFlowCount = 42 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
13.4.4 Data Set using an enterprise-specific scope
In this example, we report the following two Data Records:
Line Card ID | IPFIX Message | Exported Flow Records
-------------------------------------------------------------------
Line Card 1 (lineCardId=1) | 345 | 10201
Line Card 2 (lineCardId=2) | 690 | 20402
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 260 | Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 345 | 10201 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 690 | 20402 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Claise, et. al Standard Track [Page 57]
IPFIX Protocol Specification May 2005
14. References
14.1 Normative References
[IPFIX-ARCH] Sadasivan, G., Brownlee, N., Claise, B., Quittek, J.,
"Architecture Model for IP Flow Information Export" draft-ietf-
ipfix-arch-07.txt", March 2005
[IPFIX-INFO] Quittek, J., Bryant S., Claise, B., Meyer, J.
"Information Model for IP Flow Information Export" draft-ietf-ipfix-
info-07, May 2005
[UDP] Postel, J., "User Datagram Protocol" RFC 768, August 1980
[TCP] "TRANSMISSION CONTROL PROTOCOL DARPA INTERNET PROGRAM
PROTOCOL SPECIFICATION" RFC 793, September 1981
[RFC1889] Schulzrinne, H., Casner, S., Frederick, R., Jacobson, V.,
"RTP: A Transport Protocol for Real-Time Applications ", RFC 1889,
January 1996
[RFC2434] Alvestrand, H. and T. Narten, "Guidelines for Writing an
IANA Considerations Section in RFCs", RFC 2434, October 1998.
[RFC2402] Kent, S., Atkinson, R., "IP Authentication Header ", RFC
2402, November 1998
[RFC2406] Kent, S., Atkinson, R., "IP Encapsulating Security Payload
(ESP)", RFC 2406, November 1998
[RFC2960] Stewart, R. (ed.) "Stream Control Transmission Protocol",
RFC 2960, October 2000
[RFC3758] Stewart, R., Ramalho, M., Xie, Q., Tuexen, M., Conrad, P.
"Stream Control Transmission Protocol (SCTP) Partial Reliability
Extension", RFC 3758, May 2004
14.2 Informative References
[RFC3917] Quittek, J., Zseby, T., Claise, B., Zander, S.,
"Requirements for IP Flow Information Export" RFC 3917, October 2004
Claise, et. al Standard Track [Page 58]
IPFIX Protocol Specification May 2005
[IPFIX-AS] Zseby, T., Boschi, E., Brownlee, N., Claise, B., "IPFIX
Applicability", draft-ietf-ipfix-as-04.txt, February 2005
[RFC3955] Leinen, S., "Evaluation of Candidate Protocols for IP Flow
Information Export (IPFIX)", RFC 3955, October 2004
[RFC3954] Claise, B., et al "Cisco Systems NetFlow Services Export
Version 9", RFC 3954, October 2004
[RFC2579] McCloghrie, K., et al "Textual Conventions for SMIv2", RFC
2579, April 1999
[PEN] IANA Private Enterprise Numbers registry
http://www.iana.org/assignments/enterprise-numbers
[USEIPSEC] Bellovin, S., Guidelines for Mandating the Use of IPsec,
draft-bellovin-useipsec-02.txt, October 2003, work
in progress.
[IKE] Harkins, D. and D. Carrel, "The Internet Key Exchange
(IKE)", RFC 2409, November 1998.
[TLS] Dierks, T. and C. Allen, "The TLS Protocol Version
1.0", RFC 2246, January 1999.
[RFC1948] Bellovin, S., " Defending Against Sequence Number
Attacks", RFC 1948, May 1996
15. Acknowledgments
We would like to thank the following persons: Juergen Quittek for
the coordination job within IPFIX and PSAMP; Nevil Brownlee, Dave
Plonka, and Paul Aitken for the thorough reviews; Randall Stewart
and Peter Lei for their SCTP expertise; Martin Djernaes for the
first essay on the SCTP section; Mark Fullmer, Sebastian Zander,
Jeff Meyer, Maurizio Molina, Carter Bullard, Tal Givoly, Lutz Mark,
David Moore, Brian Trammell, Robert Lowe, Paul Calato, and many
more, for the technical review and feedback.
Authors' Addresses
Benoit Claise
Cisco Systems
Claise, et. al Standard Track [Page 59]
IPFIX Protocol Specification May 2005
De Kleetlaan 6a b1
1831 Diegem
Belgium
Phone: +32 2 704 5622
E-mail: bclaise@cisco.com
Stewart Bryant
Cisco Systems, Inc.
250, Longwater,
Green Park,
Reading, RG2 6GB,
United Kingdom
Phone: +44 (0)20 8824-8828
Email: stbryant@cisco.com
Ganesh Sadasivan
Cisco Systems, Inc.
170 W. Tasman Dr.
San Jose, CA 95134
USA
Phone: +1 (408) 527-0251
Email: gsadasiv@cisco.com
Simon Leinen
SWITCH
Limmatquai 138
P.O. Box
CH-8021 Zurich
Switzerland
Phone: +41 1 268 1536
EMail: simon@switch.ch
Thomas Dietz
NEC Europte Ltd.
Network Laboratories
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 90511-28
Email: dietz@netlab.nec.de
Intellectual Property Statement
Claise, et. al Standard Track [Page 60]
IPFIX Protocol Specification May 2005
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed
to pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; nor does it represent that
it has made any independent effort to identify any such rights.
Information on the procedures with respect to rights in RFC
documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository
at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
ipr@ietf.org.
The IETF has been notified of intellectual property rights claimed
in regard to some or all of the specification contained in this
document. For more information consult the online list of claimed
rights.
Disclaimer of Validity
This document and the information contained herein are provided on
an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Claise, et. al Standard Track [Page 61]
IPFIX Protocol Specification May 2005
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Claise, et. al Standard Track [Page 62]