INTERNET-DRAFT                              R. Hinden, Ipsilon Networks
March 27, 1995                                   S. Deering, Xerox PARC
                                                                Editors



                  IP Version 6 Addressing Architecture

                  <draft-ietf-ipngwg-addr-arch-01.txt>


Status of this Memo

   This document is an Internet-Draft.  Internet-Drafts are working
   documents of the Internet Engineering Task Force (IETF), its areas,
   and its working groups.  Note that other groups may also distribute
   working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet- Drafts as reference
   material or to cite them other than as ``work in progress.''

   To learn the current status of any Internet-Draft, please check the
   ``1id-abstracts.txt'' listing contained in the Internet- Drafts
   Shadow Directories on ds.internic.net (US East Coast), nic.nordu.net
   (Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
   Rim).

   This Internet Draft expires October 1, 1995.





















draft-ietf-ipngwg-addr-arch-01.txt                              [Page 1]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


1.0 INTRODUCTION

This specification defines the addressing architecture of the IP Version
6 protocol.  It includes a detailed description of the address formats
for IPv6 [IPV6].

The editors would like to acknowledge the contributions of Paul Francis,
Jim Bound, Brian Carpenter, Deborah Estrin, Peter Ford, Bob Gilligan,
Christian Huitema, Tony Li, Greg Minshall, Erik Nordmark, Yakov Rekhtor,
Bill Simpson, and Sue Thomson.


2.0 IPv6 ADDRESSING

IPv6 addresses are 128-bit identifiers for interfaces and sets of
interfaces.  There are three types of addresses:


    Unicast:   An identifier for a single interface.  A packet sent to a
               unicast address is delivered to the interface identified
               by that address.

    Anycast:   An identifier for a set of interfaces (typically
               belonging to different nodes).  A packet sent to an
               anycast address is delivered to one of the interfaces
               identified by that address (the "nearest" one, according
               to the routing protocols' measure of distance).

    Multicast: An identifier for a set of interfaces (typically
               belonging to different nodes).  A packet sent to a
               multicast address is delivered to all interfaces
               identified by that address.

There are no broadcast addresses in IPv6, their function being
superseded by multicast addresses.

In this document, fields in addresses are given a specific name, for
example "subscriber".  When this name is used with the term "ID" for
identifier after the name (e.g., "subscriber ID"), it refers to the
contents of the named field.  When it is used with the term "prefix"
(e.g.  "subscriber prefix") it refers to all of the address up to and
including this field.

In IPv6, all zeros and all ones are legal values for any field, unless
specifically excluded.  Specifically, prefixes may contain zero-valued
fields or end in zeros.





draft-ietf-ipngwg-addr-arch-01.txt                              [Page 2]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


2.1 Addressing Model

IPv6 Addresses of all types are assigned to interfaces, not nodes.
Since each interface belongs to a single node, any of that node's
interfaces' unicast addresses may be used as an identifier for the node.

An IPv6 unicast address refers to a single interface.  A single
interface may be assigned multiple IPv6 addresses of any type (unicast,
anycast, and multicast).  There are two exceptions to this model.  These
are:

  1) A single address may be assigned to multiple physical interfaces if
     the implementation treats the multiple physical interfaces as one
     interface when presenting it to the internet layer.  This is useful
     for load-sharing over multiple physical interfaces.

  2) Routers may have unnumbered interfaces (i.e., no IPv6 address
     assigned to the interface) on point-to-point links to eliminate the
     necessity to manually configure and advertise the addresses.
     Addresses are not need for point-to-point interfaces on routers if
     those interfaces are not to be used as the origins or destinations
     of any IPv6 datagrams.

IPv6 continues the IPv4 model that a subnet is associated with one link.
Multiple subnets may be assigned to the same link.


2.2 Text Representation of Addresses

There are three conventional forms for representing IPv6 addresses as
text strings:

  1. The preferred form is x:x:x:x:x:x:x:x, where the 'x's are the
     hexadecimal values of the eight 16-bit pieces of the address.
     Examples:

                FEDC:BA98:7654:3210:FEDC:BA98:7654:3210

                1080:0:0:0:8:800:200C:417A

     Note that it is not necessary to write the leading zeros in an
     individual field, but there must be at least one numeral in every
     field (except for the case described in 2.).

  2. Due to the method of allocating certain styles of IPv6 addresses,
     it will be common for addresses to contain long strings of zero
     bits.  In order to make writing address containing zero bits easier
     a special syntax is available to compress the zeros.  The use of



draft-ietf-ipngwg-addr-arch-01.txt                              [Page 3]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


     two "::" indicate multiple groups of 16-bits of zeros.  For example
     the multicast address:


                FF01:0:0:0:0:0:0:43

     may be represented as:

                FF01::43

     The "::" can only appear once in an address.  The "::" can also be
     used to compress the leading or trailing zeros in an address.


  3. An alternative form that is sometimes more convenient when dealing
     with a mixed environment of IPv4 and IPv6 nodes is
     x:x:x:x:x:x:d.d.d.d, where the 'x's are the hexadecimal values of
     the six high-order 16-bit pieces of the address, and the 'd's are
     the decimal values of the four low-order 8-bit pieces of the
     address (standard IPv4 representation).  Examples:

                0:0:0:0:0:0:13.1.68.3

                0:0:0:0:0:FFFF:129.144.52.38

     or in compressed form:

                ::13.1.68.3

                ::FFFF:129.144.52.38


2.3 Address Type Representation

The specific type of an IPv6 address is indicated by the leading bits in
the address.  The variable-length field comprising these leading bits is
called the Format Prefix (FP).  The initial allocation of these prefixes
is as follows:













draft-ietf-ipngwg-addr-arch-01.txt                              [Page 4]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


     Allocation                         Prefix         Fraction of
                                        (binary)       Address Space
     -------------------------------    --------       -------------
     Reserved                           0000 0000      1/256
     Unassigned                         0000 0001      1/256

     Reserved for NSAP Allocation       0000 001       1/128
     Reserved for IPX Allocation        0000 010       1/128

     Unassigned                         0000 011       1/128
     Unassigned                         0000 1         1/32
     Unassigned                         0001           1/16
     Unassigned                         001            1/8

     Provider-Based Unicast Address     010            1/8

     Unassigned                         011            1/8

     Reserved for Neutral-Interconnect-
     Based Unicast Addresses            100            1/8

     Unassigned                         101            1/8
     Unassigned                         110            1/8
     Unassigned                         1110           1/16
     Unassigned                         1111 0         1/32
     Unassigned                         1111 10        1/64
     Unassigned                         1111 110       1/128

     Unassigned                         1111 1110 0    1/512

     Link Local Use Addresses           1111 1110 10   1/1024
     Site Local Use Addresses           1111 1110 11   1/1024

     Multicast Addresses                1111 1111      1/256

     Note: The "unspecified address" (see section 2.4.2), the loopback
     address (see section 2.4.3), and the IPv6 Addresses with Embedded
     IPv4 Addresses (see section 2.4.4), are assigned out of the 0000
     0000 format prefix space.


This allocation supports the direct allocation of provider addresses,
local use addresses, and multicast addresses.  Space is reserved for
NSAP addresses, IPX addresses, and neutral-interconnect addresses.  The
remainder of the address space is unassigned for future use.  This can
be used for expansion of existing use (e.g., additional provider
addresses, etc.) or new uses (e.g., separate locators and identifiers).
Fifteen percent of the address space is initially allocated.  The



draft-ietf-ipngwg-addr-arch-01.txt                              [Page 5]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


remaining 85% is reserved for future use.

Unicast addresses are distinguished from multicast addresses by the
value of the high-order octet of the addresses: a value of FF (11111111)
identifies an address as a multicast address; any other value identifies
an address as a unicast address.  Anycast addresses are taken from the
unicast address space, and are not syntactically distinguishable from
unicast addresses.


2.4 Unicast Addresses

The IPv6 unicast address is contiguous bit-wise maskable, similar to
IPv4 addresses under Class-less Interdomain Routing [CIDR].

There are several forms of unicast address assignment in IPv6, including
the global provider based unicast address, the neutral-interconnect
unicast address, the NSAP address, the IPX hierarchical address, the
site-local-use address, the link-local-use address, and the IPv4-capable
host address.  Additional addresses types can be defined in the future.

IPv6 nodes may have considerable or little knowledge of the internal
structure of the IPv6 address, depending on the role the node plays (for
instance, host versus router).  At a minimum, a node may consider that
unicast addresses (including its own) have no internal structure:

 |                           128 bits                              |
 +-----------------------------------------------------------------+
 |                          node address                           |
 +-----------------------------------------------------------------+


A slightly sophisticated host (but still rather simple) may additionally
be aware of subnet prefix(es) for the link(s) it is attached to, where
different addresses may have different values for n:

 |                         n bits                 |   128-n bits   |
 +------------------------------------------------+----------------+
 |                   subnet prefix                | interface ID   |
 +------------------------------------------------+----------------+


Still more sophisticated hosts may be aware of other hierarchical
boundaries in the unicast address.  Though a very simple router may have
no knowledge of the internal structure of IPv6 unicast addresses,
routers will more generally have knowledge of one or more of the
hierarchical boundaries for the operation of routing protocols.  The
known boundaries will differ from router to router, depending on what



draft-ietf-ipngwg-addr-arch-01.txt                              [Page 6]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


positions the router holds in the routing hierarchy.


2.4.1 Unicast Address Examples

An example of a Unicast address format which will likely be common on
LANs and other environments where IEEE 802 MAC addresses are available
is:


 |              n bits            |  m bits   |     48 bits        |
 +--------------------------------+-----------+--------------------+
 |        subscriber prefix       | subnet ID |   interface ID     |
 +--------------------------------+-----------+--------------------+

Where the 48-bit Interface ID is an IEEE-802 MAC address.  The use of
IEEE 802 MAC addresses as a interface ID is expected to be very common
in environments where nodes have an IEEE 802 MAC address.  In other
environments, where IEEE 802 MAC addresses are not available, other
types of link layer addresses can be used, such as E.164 addresses, for
the interface ID.

The inclusion of a unique global interface identifier, such as an IEEE
MAC address, makes possible a very simple form of auto-configuration of
addresses.  A node may discover a subnet ID by listening to General
Advertisement messages send by a router on its attached link(s), and
then fabricating a IPv6 address for itself by using its IEEE MAC address
as the interface ID on that subnet.

Another unicast address format example is where a site or organization
requires additional layers of internal hierarchy.  In this example the
subnet ID is divided into an area ID and a subnet ID.  Its format is:

 |         s bits       | n bits  |   m bits     | 128-s-n-m bits  |
 +----------------------+---------+--------------+-----------------+
 |   subscriber prefix  | area ID |  subnet ID   |  interface ID   |
 +----------------------+---------+--------------+-----------------+

This technique can be continued to allow a site or organization to add
additional layers of internal hierarchy.  It may be desirable to use an
interface ID smaller than a 48-bit IEEE 802 MAC address to allow more
space for the additional layers of internal hierarchy.  These could be
interface IDs which are administratively created by the site or
organization.







draft-ietf-ipngwg-addr-arch-01.txt                              [Page 7]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


2.4.2 The Unspecified Address

The address 0:0:0:0:0:0:0:0 is called the unspecified address.  It must
never be assigned to any node.  It indicates the absence of an address.
One example of its use is in the Source Address field of any IPv6
datagrams sent by an initializing host before it has learned its own
address.

The unspecified address must not be used as the destination address of
IPv6 datagrams or in IPv6 Routing Headers.


2.4.3 The Loopback Address

The unicast address 0:0:0:0:0:0:0:1 is called the loopback address. It
may be used by a node to send a IPv6 datagram to itself.  It may never
be assigned to any interface.

The loopback address must not be used as the source address in IPv6
datagrams that are sent outside of a single node.


2.4.4 IPv6 Addresses with Embedded IPv4 Addresses

The IPv6 transition mechanisms include a technique for hosts and routers
to dynamically tunnel IPv6 packets over IPv4 routing infrastructure.
IPv6 nodes that utilize this technique are assigned special IPv6 unicast
addresses that carry an IPv4 address in the low-order 32-bits.  This
type of address is termed an "IPv4-compatible IPv6 address" and has the
format:


 |                80 bits               | 16 |      32 bits        |
 +--------------------------------------+--------------------------+
 |0000..............................0000|0000|    IPv4 address     |
 +--------------------------------------+----+---------------------+


A second type of IPv6 address which holds an embedded IPv4 address is
also defined.  This address is used to represent the addresses of IPv4-
only nodes (those that *do not* support IPv6) as IPv6 addresses.  This
type of address is termed an "IPv4-mapped IPv6 address" and has the
format:








draft-ietf-ipngwg-addr-arch-01.txt                              [Page 8]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995



 |                80 bits               | 16 |      32 bits        |
 +--------------------------------------+--------------------------+
 |0000..............................0000|FFFF|    IPv4 address     |
 +--------------------------------------+----+---------------------+



2.4.5 NSAP Addresses

This mapping of NSAP address into IPv6 addresses is as follows:


 |   7   |                   121 bits                              |
 +-------+---------------------------------------------------------+
 |0000001|                 to be defined                           |
 +-------+---------------------------------------------------------+

The draft definition, motivation, and usage are under study [NSAP].


2.4.6 IPX Addresses

This mapping of IPX address into IPv6 addresses is as follows:


 |   7   |                   121 bits                              |
 +-------+---------------------------------------------------------+
 |0000010|                 to be defined                           |
 +-------+---------------------------------------------------------+

The draft definition, motivation, and usage are under study.


2.4.7 Provider-Based Global Unicast Addresses

The global provider-based unicast address is assigned as described in
[ALLOC] and [ADDRF].  This assignment strategy is similar to assignment
of IPv4 addresses under the CIDR scheme [CIDR].  The IPv6 global
provider-based unicast address format is as follows:

                                                      | 125-m-n- |
  | 3 |  n bits   |  m bits   |   o bits    | p bits  | o-p bits |
  +---+-----------+-----------+-------------+---------+----------+
  |010|registry ID|provider ID|subscriber ID|subnet ID| intf. ID |
  +---+-----------+-----------+-------------+---------+----------+

The high-order part of the address is assigned to registries, who then



draft-ietf-ipngwg-addr-arch-01.txt                              [Page 9]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


assign portions of the address space to providers, who then assign
portions of the address space to subscribers, etc.

The registry ID identifies the registry which assigns the provider
portion of the address.  The term "registry prefix" refers to the high-
order part of the address up to and including the registry ID.

The provider ID identifies a specific provider which assigns the
subscriber portion of the address.  The term "provider prefix" refers to
the high-order part of the address up to and including the provider ID.

The subscriber ID distinguishes among multiple subscribers attached to
the provider identified by the provider ID.  The term "subscriber
prefix" refers to the high-order part of the address up to and including
the subscriber ID.

The subnet ID identifies a specific physical link.  There can be
multiple subnets on the same physical link.  A specific subnet can not
span multiple physical links.  The term "subnet prefix" refers to the
high-order part of the address up to and including the subnet ID.  The
group of nodes identified by the subnet ID must be attached to the same
link.

The interface ID identifies a single interface among the group of
interfaces identified by the subnet prefix.


2.4.8 Local-use IPv6 Unicast Addresses

There are two types of local-use unicast addresses defined.  These are
Link-Local and Site-Local.  The Link-Local is for use on a single link
and the Site-Local is for use in a single site.  Link-Local addresses
have the following format:

 |  10      |
 | bits     |        n bits           |       118-n bits           |
 +----------+-------------------------+----------------------------+
 |1111111010|           0             |       interface ID         |
 +----------+-------------------------+----------------------------+


Link-Local addresses are designed to be used for addressing on a single
link for purposes such as auto-address configuration or when no routers
are present.

Site-Local addresses have the following format:





draft-ietf-ipngwg-addr-arch-01.txt                             [Page 10]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995



 |   10     |
 |  bits    | n bits  |    m bits     |       118-n-m bits         |
 +----------+---------+---------------+----------------------------+
 |1111111011|    0    |   subnet ID   |       interface ID         |
 +----------+---------+---------------+----------------------------+



Site-Local addresses may be used for sites or organizations that are not
(yet) connected to the global Internet.  They do not need to request or
"steal" an address prefix from the global Internet address space.  IPv6
site-local addresses can be used instead.  When the organization
connects to the global Internet, it can then form global addresses by
replacing the site-local prefix with a subscriber prefix.


2.5 Anycast Addresses

An IPv6 anycast address is an address that is assigned to more than one
interface (typically belonging to different nodes), with the property
that a packet sent to an anycast address is routed to the nearest
interface having that address, according to the routing protocols'
measure of distance.

Anycast addresses are allocated from the unicast address space, using
any of the defined unicast address formats.  Thus, anycast addresses are
syntactically indistinguishable from unicast addresses.  When a unicast
address is assigned to more than one interface, thus turning it into an
anycast address, the nodes to which the address is assigned must be
explicitly configured to know that it is an anycast address.

For any assigned anycast address, there is a longest address prefix P
that identifies the topological region in which all interfaces belonging
to that anycast address reside.  Within the region identified by P, each
member of the anycast set must be advertised as a separate entry in the
routing system (commonly referred to as a "host route"); outside the
region identified by P, the anycast address may be aggregated into the
routing advertisement for prefix P.

Note that in, the worst case, the prefix P of an anycast set may be the
null prefix, i.e., the members of the set may have no topological
locality.  In that case, the anycast address must be advertised as a
separate routing entry throughout the entire internet, which presents a
severe scaling limit on how many such "global" anycast sets may be
supported.  Therefore, it is expected that support for global anycast
sets may be unavailable or very restricted.




draft-ietf-ipngwg-addr-arch-01.txt                             [Page 11]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


One expected use of anycast addresses is to identify the set of routers
belonging to an internet service provider.  Such addresses could be used
as intermediate addresses in an IPv6 Routing header, to cause a packet
to be delivered via a particular provider or sequence of providers.
Some other possible uses are to identify the set of routers attached to
a particular subnet, or the set of routers providing entry into a
particular routing domain.

There is little experience with widespread, arbitrary use of internet
anycast addresses, and some known complications and hazards when using
them in their full generality [ANYCST].  Until more experience has been
gained and solutions agreed upon for those problems, the following
restrictions are imposed on IPv6 anycast addresses:

   o An anycast address MUST NOT be used as the source address of an
     IPv6 packet.

   o An anycast address MUST NOT be assigned to an IPv6 host, that is,
     it may be assigned to an IPv6 router only.


2.6 Multicast Addresses

A IPv6 multicast address is an identifier for a group of nodes.  A node
may belong to any number of multicast groups.  Multicast addresses have
the following format:

 |   8    |  4 |  4 |                  112 bits                   |
 +------ -+----+----+---------------------------------------------+
 |11111111|flgs|scop|                  group ID                   |
 +--------+----+----+---------------------------------------------+

     11111111 at the start of the address identifies the address as
     being a multicast address.

                                   +-+-+-+-+
     flgs is a set of 4 flags:     |0|0|0|T|
                                   +-+-+-+-+

          The high-order 3 flags are reserved, and must be initialized
          to 0.

          T = 0 indicates a permanently-assigned ("well-known")
          multicast address, assigned by the global internet numbering
          authority.

          T = 1 indicates a non-permanently-assigned ("transient")
          multicast address.



draft-ietf-ipngwg-addr-arch-01.txt                             [Page 12]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


     scop is a 4-bit multicast scope value used to limit the scope of
     the multicast group.  The values are:

          0  reserved
          1  node-local scope
          2  link-local scope
          3  (unassigned)
          4  (unassigned)
          5  site-local scope
          6  (unassigned)
          7  (unassigned)
          8  organization-local scope
          9  (unassigned)
          A  (unassigned)
          B  community-local scope
          C  (unassigned)
          D  (unassigned)
          E  global scope
          F  reserved

     group ID identifies the multicast group, either permanent or
     transient, within the given scope.

The "meaning" of a permanently-assigned multicast address is independent
of the scope value.  For example, if the "NTP servers group" is assigned
a permanent multicast address with a group ID of 43 (hex), then:

     FF01:0:0:0:0:0:0:43 means all NTP servers on the same node as the
     sender.

     FF02:0:0:0:0:0:0:43 means all NTP servers on the same link as the
     sender.

     FF05:0:0:0:0:0:0:43 means all NTP servers at the same site as the
     sender.

     FF0E:0:0:0:0:0:0:43 means all NTP servers in the internet.


Non-permanently-assigned multicast addresses are meaningful only within
a given scope.  For example, a group identified by the non-permanent,
site-local multicast address FF15:0:0:0:0:0:0:43 at one site bears no
relationship to a group using the same address at a different site, nor
to a non-permanent group using the same group ID with different scope,
nor to a permanent group with the same group ID.

Multicast addresses must not be used as source addresses in IPv6
datagrams or appear in any routing header.



draft-ietf-ipngwg-addr-arch-01.txt                             [Page 13]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


2.6.1 Pre-Defined Multicast Addresses

The following well-known multicast addresses are pre-defined:

     Reserved Multicast Addresses:   FF00:0:0:0:0:0:0:0
                                     FF01:0:0:0:0:0:0:0
                                     FF02:0:0:0:0:0:0:0
                                     FF03:0:0:0:0:0:0:0
                                     FF04:0:0:0:0:0:0:0
                                     FF05:0:0:0:0:0:0:0
                                     FF06:0:0:0:0:0:0:0
                                     FF07:0:0:0:0:0:0:0
                                     FF08:0:0:0:0:0:0:0
                                     FF09:0:0:0:0:0:0:0
                                     FF0A:0:0:0:0:0:0:0
                                     FF0B:0:0:0:0:0:0:0
                                     FF0C:0:0:0:0:0:0:0
                                     FF0D:0:0:0:0:0:0:0
                                     FF0E:0:0:0:0:0:0:0
                                     FF0F:0:0:0:0:0:0:0

The above multicast addresses are reserved and shall never be assigned
to any multicast group.

     All Nodes Addresses:    FF01:0:0:0:0:0:0:1
                             FF02:0:0:0:0:0:0:1

The above multicast addresses identify the group of all IPv6 nodes,
within scope 1 (node-local) or 2 (link-local).

     All Routers Addresses:   FF01:0:0:0:0:0:0:2
                              FF02:0:0:0:0:0:0:2

The above multicast addresses identify the group of all IPv6 routers,
within scope 1 (node-local) or 2 (link-local).

     All Hosts Addresses:     FF01:0:0:0:0:0:0:3
                              FF02:0:0:0:0:0:0:3

The above multicast addresses identify the group of all IPv6 hosts,
within scope 1 (node-local) or 2 (link-local).


2.7 A Node's Required Addresses

A host is required to recognize the following addresses as identifying
itself:




draft-ietf-ipngwg-addr-arch-01.txt                             [Page 14]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


   o Assigned Unicast Addresses
   o Loopback Address
   o All Nodes Multicast Address
   o All Hosts Multicast Address
   o All other Multicast Addresses to which the host belongs.

A router is required to recognize the following addresses as identifying
itself:

   o Assigned Unicast Addresses
   o Loopback Address
   o All anycast addresses with which the router has been configured.
   o All Nodes Multicast Address
   o All Router Multicast Address
   o All other Multicast Addresses to which the router belongs.

The only address-prefixes which should be predefined in an
implementation are the:

   o Unspecified Address
   o Loopback Address
   o Multicast prefix (FF)
   o Pre-Defined Multicast Addresses
   o IPv4 Compatible Prefixes

Implementations should assume all other addresses are unicast unless
specifically configured (e.g., anycast addresses).
























draft-ietf-ipngwg-addr-arch-01.txt                             [Page 15]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


REFERENCES


  [ADDRF] Rekhter, Y., Lothberg, P., "An IPv6 Global Unicast Address
          Format", Internet Draft

  [ALLOC] Rekhter, Y., Li, T., "An Architecture for IPv6 Unicast Address
          Allocation", Internet Draft

  [ANYCST]C. Partridge, T. Mendez, and W. Milliken, "Host Anycasting
          Service", RFC-1546, November 1993.

  [CIDR]  V. Fuller, T. Li, K. Varadhan, J. Yu, "Supernetting: an
          Address Assignment and Aggregation Strategy", RFC 1338.

  [IPV6]  S. Deering, R. Hinden, Editors, "Internet Protocol, Version 6
          (IPv6) Specification", Internet Draft.

  [MULT]  S. Deering, "Host Extensions for IP multicasting", RFC 1112.

  [NSAP]  B.Carpenter, Editor, "Mechanisms for OSI NSAPs, CLNP and TP
          over IPv6", Internet Draft.




DOCUMENT EDITOR'S ADDRESS

     Robert M. Hinden                     Stephen E. Deering
     Ipsilon Networks, Inc.               Xerox Palo Alto Research Center
     2465 Latham Street, Suite 100        3333 Coyote Hill Road
     Mt. View, CA 94040                   Palo Alto, CA 94304
     USA                                  USA

     phone: +1 415 528 4604               phone: +1 415 812 4839
     fax:   +1 415 528 4653               fax:   +1 415 812 4471
     email: hinden@ipsilon.com            email: deering@parc.xerox.com














draft-ietf-ipngwg-addr-arch-01.txt                             [Page 16]


INTERNET-DRAFT        IPv6 Addressing Architecture            March 1995


APPENDIX

Changes from Previous Version

   This version of the "IPv6 Addressing Architecture" includes the
   following changes made since the previous version:

        o Region addresses replace by Anycast addresses.

        o Reduced references to other documents.

        o Reordered the unicast sections of the document.

        o Changed Multicast All Routers and All Hosts to be consistent
          with IPv4 multicast assignment.

        o Minor clarification's, corrections, and typos fixed.

        o New typos likely added.
































draft-ietf-ipngwg-addr-arch-01.txt                             [Page 17]