Internet-Draft Sean Harnedy
InfiniSwitch Corp.
Expiration Date: August 2003 February 2003
Definitions of Managed Objects for the
Infiniband Performance Management Agent (PMA)
<draft-ietf-ipoib-perf-mgmt-agent-mib-01.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines objects for managing InfiniBand Performance
Management Agents (PMA).
Table of Contents
1. Introduction ................................................. 2
2. The SNMP Management Framework ................................ 2
3. Conventions used in this document ............................ 3
4. Structure of the MIB ......................................... 3
4.1. Overview ................................................... 3
4.2. Discussion of MIB Groups ................................... 3
4.3. The PMA MIB Objects ........................................ 3
4.3.1 The PMA Port Counters Mandatory Group .................... 3
4.3.2 The PMA Port Counters Optional Group ..................... 4
4.3.3 The PMA Port Receive Error Group ......................... 4
4.3.4 The PMA Port Transmit Discard Details Group .............. 4
Expires August 2003 [Page 1]
Internet-Draft IPOVERIB PMA MIB February 2003
4.3.5 The PMA Port Flow Control Counters Group ................ 4
4.3.6 The PMA Port Op Code Receive Counters Group .............. 4
4.3.7 The PMA Port Op Code VL Counters Group .................. 4
4.3.8 The PMA Port Op Code VL Data Counters Group .............. 4
4.3.9 The PMA Port VL Transmit Flow Control Update Error Group . 4
4.3.10 The PMA Port VL Transmit Wait Group ..................... 4
4.3.11 The PMA Port VL Software Congestion Group ............... 4
4.4. The PMA Conformance Group .................................. 4
4.4.1. PMA Compliance Groups .................................... 4
5. IPOIB PMA MIB Definitions .................................... 5
6. Security Considerations ...................................... 54
7. Intellectual Property ........................................ 54
8 References ................................................... 55
9. Author's Address ............................................. 56
1. Introduction
This document defines a MIB for the InfiniBand Performance Managment
Agent (PMA).
The Infiniband Architecture[IBTAArch] is defined by the Infiniband
Trade Association. Infiniband is designed to provide low latency
high bandwidth interconnect in a computing environment. This
document will define the objects related to managing the Performance
Management Agent on each device in an InfiniBand Fabric.
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571[RFC2571].
o Mechanisms for describing and naming objects and events for
the purpose of management. The first version of this
Structure of Management Information (SMI) is called SMIv1
and described in STD 16, RFC 1155[RFC1155], STD 16, RFC 1212
[RFC1212] and RFC 1215 [RFC1215]. The second version,
called SMIv2, is described in STD 58, RFC 2578[RFC2578], STD
58, RFC 2579[RFC2579], and STD 58, RFC 2580[RFC2580].
o Message protocols for transferring management information.
The first version of the SNMP message protocol is called
SNMPv1 and described in STD 15, RFC 1157[RFC1157]. A second
version of the SNMP message protocol, which is not an
Internet standards track protocol, is called SNMPv2c and
described in RFC 1901[RFC1901] and RFC 1906[RFC1906]. The
third version of the message protocol is called SNMPv3 and
described in RFC 1906[RFC1906], RFC 2572[RFC2572] and RFC
2574[RFC2574].
o Protocol operations for accessing management information.
The first set of protocol operations and associated PDU
Expires August 2003 [Page 2]
Internet-Draft IPOVERIB PMA MIB February 2003
formats is described in STD 15, RFC 1157[RFC1157]. A second
set of protocol operations and associated PDU formats is
described in RFC 1905[RFC1905].
o A set of fundamental applications described in RFC
2573[RFC2573] and the view-based access control mechanism
described in RFC 2575[RFC2575].
A more detailed introduction to the current SNMP Management
Framework can be found in RFC 2570[RFC2570].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. Objects in the MIB
are defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2.
A MIB conforming to the SMIv1 can be produced through the
appropriate translations. The resulting translated MIB must be
semantically equivalent, except where objects or events are
omitted because no translation is possible (use of Counter64).
Some machine readable information in SMIv2 will be converted into
textual descriptions in SMIv1 during the translation process.
However, this loss of machine readable information is not
considered to change the semantics of the MIB.
3. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC 2119 [RFC2119].
4. Structure of the MIB
This section describes the structure of the IPOIB PMA MIB.
4.1. Overview
The SNMP management of the PMA involves the monitoring of key
management attributes. The PMA is manadatory on all InfiniBand
nodes.
4.2. Discussion of MIB Groups
The PMA MIB is divided into two basic groups: MIB objects and
the conformance section.
4.3. The PMA MIB Objects
There are eleven general groups of PMA MIB objects.
4.3.1 The PMA Port Counters Mandatory Group
Expires August 2003 [Page 3]
Internet-Draft IPOVERIB PMA MIB February 2003
This group provides the mandatory PMA port counters.
4.3.2 The PMA Port Counters Optional Group
This group provides the optional PMA port counters.
4.3.3 The PMA Port Receive Error Group
This group provides the receive errors PMA port counters.
4.3.4 The PMA Port Transmit Discard Details Group
This group provides the transmit discard details PMA
port counters.
4.3.5 The PMA Port Flow Control Counters Group
This group provides the flow control PMA port counters.
4.3.6 The PMA Port Op Code Receive Counters Group
This group provides the op code receive PMA port counters.
4.3.7 The PMA Port Op Code VL Counters Group
This group provides the op code VL PMA port counters.
4.3.8 The PMA Port Op Code VL Data Counters Group
This group provides the op code VL data PMA port counters.
4.3.9 The PMA Port VL Transmit Flow Control Update Error Group
This group provides the VL transmit flow control update errors
PMA port counters.
4.3.10 The PMA Port VL Transmit Wait Group
This group provides the VL transmit wait PMA port counters.
4.3.11 The PMA Port VL Software Congestion Group
This group provides the VL software congestion PMA port counters.
4.4. The PMA Conformance Group
The PMA Conformance Group lists the possible compliances for
various types of InfiniBand nodes (basic and full), and the
units of conformance that define the constituent object groups.
4.4.1. PMA Compliance Groups
The PMA Compliance Groups list acceptable MIB implementation
Expires August 2003 [Page 4]
Internet-Draft IPOVERIB PMA MIB February 2003
requirements.
5. IPOIB PMA MIB Definitions
PMA-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
NOTIFICATION-TYPE, Integer32, Counter32 FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
IbDataPort, infinibandMIB FROM IB-TC-MIB;
ibPmaMIB MODULE-IDENTITY
LAST-UPDATED "200302011200Z" -- February 1, 2003
ORGANIZATION "IETF IP Over IB Working Group
Email: ipoib@ietf.org"
CONTACT-INFO
"Sean Harnedy (sharnedy@infiniswitch.com)
InfiniSwitch Corporation"
DESCRIPTION
"This module contains managed object definitions for
the Performance Management Agent instrumentation for an
InfiniBand Performance Management Agent (PMA)."
REVISION
"200302011200Z" -- February 1, 2003 12:00:00 GMT
DESCRIPTION
"Updated MIB to IBTA Spec Version 1.1 (-01)."
REVISION
"200210191200Z" -- October 19, 2002 12:00:00 GMT
DESCRIPTION
"Initial IETF Draft Revision (-00)."
::= { infinibandMIB 6 }
--****************************************************************
-- Object Indentifiers for the IPOIB PMA MIB
--****************************************************************
ibPmaObjects OBJECT IDENTIFIER ::= { ibPmaMIB 1 }
ibPmaConformance OBJECT IDENTIFIER ::= { ibPmaMIB 2 }
--****************************************************************
-- Port Counters Group
--
-- DESCRIPTION: This Group provides basic performance and exception
-- statistics for a port. This group contains 2 tables: one for
-- the mandatory counters and one for the optional counters.
-- These objects are based on the PortCounters attribute.
--
-- NOTE: during operation, instead of "overflowing" these counters
-- stop at all 1's (until reset by the PMA).
--****************************************************************
ibPmaPortCntrsInfo OBJECT IDENTIFIER ::= { ibPmaObjects 1 }
Expires August 2003 [Page 5]
Internet-Draft IPOVERIB PMA MIB February 2003
--****************************************************************
-- The Mandatory Port Counters Table
--****************************************************************
ibPmaPortCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Counters information."
::= { ibPmaPortCntrsInfo 1 }
ibPmaPortCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortCntrsTable containing
information about the basic performance and exception
statistics for a particular data port."
INDEX { ibPmaPortCntrsIndex }
::= { ibPmaPortCntrsTable 1 }
IbPmaPortCntrsEntry ::= SEQUENCE {
ibPmaPortCntrsIndex IbDataPort,
ibPmaSymbolErrCounter Integer32,
ibPmaLinkErrRecoveryCntr Integer32,
ibPmaLinkDownedCntr Integer32,
ibPmaPortRcvErr Integer32,
ibPmaPortRcvRemPhysErr Integer32,
ibPmaPortRcvSwitchRelayErr Integer32,
ibPmaPortXmitDiscard Integer32,
ibPmaPortXmitConstraintErr Integer32,
ibPmaPortRcvConstraintErr Integer32,
ibPmaLocalLinkIntegrityErr Integer32,
ibPmaExcessBufOverrunErr Integer32,
ibPmaVl15Dropped Integer32
}
ibPmaPortCntrsIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortCntrsEntry 1 }
ibPmaSymbolErrCounter OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
Expires August 2003 [Page 6]
Internet-Draft IPOVERIB PMA MIB February 2003
DESCRIPTION
"Total number of symbol errors detected on one or more
physical lanes."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortSymbolErrorCounter."
::= { ibPmaPortCntrsEntry 2 }
ibPmaLinkErrRecoveryCntr OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of times the Port Training state machine has
successfully completed the link error recovery process."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::LinkErrorRecoveryCounters."
::= { ibPmaPortCntrsEntry 3 }
ibPmaLinkDownedCntr OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of times the Port Training state machine has
failed the link error recovery process and downed the link."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::LinkDownedCounter."
::= { ibPmaPortCntrsEntry 4 }
ibPmaPortRcvErr OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets containing an error that were
received on the port. These errors include:
- Local physical errors (ICRC, VCRC, FCCRC, and all physical
errors that cause entry into the BAD PACKET of BAD PACKET
DISCARD states of the packet receiver state machine)
- Malformed data packet errors (LVer, length, VL)
- Malformed link packet errors (operand, length, VL)
- Packets discarded due to buffer overrun."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvErrors."
::= { ibPmaPortCntrsEntry 5 }
Expires August 2003 [Page 7]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortRcvRemPhysErr OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets marked with the End-of-Bad-Packets (EBP)
delimeter received on the port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvRemotePhysicalErrors."
::= { ibPmaPortCntrsEntry 6 }
ibPmaPortRcvSwitchRelayErr OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that are
discarded because they could not be forwarded by the
switch relay. Reasons for this include:
- DLID mapping
- VL mapping
- looping (output port = input port)"
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvSwitchRelayErrors."
::= { ibPmaPortCntrsEntry 7 }
ibPmaPortXmitDiscard OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of outbound packets discarded by the port because the
port is down or congested. Reasons for this include:
- output port is in the inactive state
- packet length exceeded neighbor MTU
- switch lifetime limit exceeded
- switch HOQ limit exceeded
May also include packets discarded while in VLStalled state."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortXmitDiscards."
::= { ibPmaPortCntrsEntry 8 }
Expires August 2003 [Page 8]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortXmitConstraintErr OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets not transmitted from the port
for the following reasons:
- FilterRawOutbound is true and packet is raw
- PartitionEnforcementOutbound is true and packet fails
partition key check or IP version check."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortXmitConstraintErrors."
::= { ibPmaPortCntrsEntry 9 }
ibPmaPortRcvConstraintErr OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that are
discarded for the following reasons:
- FilterRawInbound is true and packet is raw
- PartitionEnforcementInbound is true and packet fails
partition key check or IP version check."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvConstraintErrors."
::= { ibPmaPortCntrsEntry 10 }
ibPmaLocalLinkIntegrityErr OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the count of packets containing
local physical errors exceeded the local physical errors
threshold."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::LocalLinkIntegrityErrors."
::= { ibPmaPortCntrsEntry 11 }
Expires August 2003 [Page 9]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaExcessBufOverrunErr OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that overrun errors consecutive flow
control update periods occurred with at least one overrun
error in each period."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::ExcessiveBufferOverrunErrors."
::= { ibPmaPortCntrsEntry 12 }
ibPmaVl15Dropped OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of incoming VL 15 packets dropped due to resource
limitations on port due to lack of buffers."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::VL15Dropped."
::= { ibPmaPortCntrsEntry 13 }
--****************************************************************
-- The Optional Port Counters Table
--****************************************************************
ibPmaPortCntrsOptTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortCntrsOptEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the optional PMA Port Counters information."
::= { ibPmaPortCntrsInfo 2 }
ibPmaPortCntrsOptEntry OBJECT-TYPE
SYNTAX IbPmaPortCntrsOptEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortCntrsOptTable containing
information about the optional performance and exception
statistics for a particular data port."
INDEX { ibPmaPortCntrsOptIndex }
::= { ibPmaPortCntrsOptTable 1 }
Expires August 2003 [Page 10]
Internet-Draft IPOVERIB PMA MIB February 2003
IbPmaPortCntrsOptEntry ::= SEQUENCE {
ibPmaPortCntrsOptIndex IbDataPort,
ibPmaPortXmitData Integer32,
ibPmaPortRcvData Integer32,
ibPmaPortXmitPkts Integer32,
ibPmaPortRcvPkts Integer32
}
ibPmaPortCntrsOptIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortCntrsOptEntry 1 }
ibPmaPortXmitData OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets divided by 4, transmitted on
all VLs from the port. This includes all octets between (and
not including) the start of packet delimeter and the VCRC. It
excludes all link packets but may include packets containing
errors. NOTE: This counter is optional and should have a 0
value if not implemented."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortXmitData."
::= { ibPmaPortCntrsOptEntry 2 }
ibPmaPortRcvData OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets divided by 4, received on
all VLs from the port. This includes all octets between (and
not including) the start of packet delimeter and the VCRC. It
excludes all link packets but may include packets containing
errors. NOTE: This counter is optional and should have a 0
value if not implemented."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvData."
::= { ibPmaPortCntrsOptEntry 3 }
Expires August 2003 [Page 11]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortXmitPkts OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets, excluding link packets, transmitted on
all VLs from the port. It may include packets with errors.
NOTE: This counter is optional and should have a 0 value if
not implemented."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortXmitPkts."
::= { ibPmaPortCntrsOptEntry 4 }
ibPmaPortRcvPkts OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets, including packets containing errors
and excluding link packets, received on all VLs on this port.
It may include packets with errors. NOTE: This counter is
optional and should have a 0 value if not implemented."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 191 PortCounters::PortRcvPkts."
::= { ibPmaPortCntrsOptEntry 5 }
--****************************************************************
-- Port Transmit and Receive Error Group
--
-- DESCRIPTION: This Group provides details for receive errors and
-- transmit discard details for each port. This group contains
-- three tables: The Port Receive Error Details table, The Port
-- Transmit Discard Details table, and The Port Flow Control
-- Counters Table.
-- These three tables are optional.
--
-- NOTE: during operation, instead of "overflowing" these counters
-- stop at all 1's (until reset by the PMA).
--****************************************************************
ibPmaPortXmitRecvInfo OBJECT IDENTIFIER ::= { ibPmaObjects 2 }
--****************************************************************
-- The Port Receive Error Details Table
--****************************************************************
Expires August 2003 [Page 12]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortRcvErrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortRcvErrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Receive Error information."
::= { ibPmaPortXmitRecvInfo 1 }
ibPmaPortRcvErrEntry OBJECT-TYPE
SYNTAX IbPmaPortRcvErrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortRcvErrTable containing
information about the receive error statistics for a
particular data port."
INDEX { ibPmaPortRcvErrIndex }
::= { ibPmaPortRcvErrTable 1 }
IbPmaPortRcvErrEntry ::= SEQUENCE {
ibPmaPortRcvErrIndex IbDataPort,
ibPmaPortRcvErrLocalPhysErrs Integer32,
ibPmaPortMalformedPacketErrs Integer32,
ibPmaPortBufferOverrunErrs Integer32,
ibPmaPortDLIDMappingErrs Integer32,
ibPmaPortVLMappingErrs Integer32,
ibPmaPortLoopingErrs Integer32
}
ibPmaPortRcvErrIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortRcvErrEntry 1 }
ibPmaPortRcvErrLocalPhysErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that contain local
physical errors (ICRC, VCRC, FCCRC, and all physical errors that
cause entry into the BAD PACKET or BAD PACKET DISCARD states of
the packet receiver state machine)."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortLocalPhysicalErrors."
::= { ibPmaPortRcvErrEntry 2 }
Expires August 2003 [Page 13]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortMalformedPacketErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that contain
malformed packet errors.
-data packets: LVer, length, VL
-link packets: operand, length VL"
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortMalformedPacketErrors."
::= { ibPmaPortRcvErrEntry 3 }
ibPmaPortBufferOverrunErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that were
discarded due to buffer overrun."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortBufferOverrunErrors."
::= { ibPmaPortRcvErrEntry 4 }
ibPmaPortDLIDMappingErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that were
discarded because they could not be forwarded by the switch
relay due to DLID mapping errors. This only applies to
switches."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortDLIDMappingErrors."
::= { ibPmaPortRcvErrEntry 5 }
ibPmaPortVLMappingErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that were
discarded because they could not be forwarded by the switch
relay due to VL mapping errors."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortVLMappingErrors."
::= { ibPmaPortRcvErrEntry 6 }
Expires August 2003 [Page 14]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortLoopingErrs OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received on the port that were
discarded because they could not be forwarded by the switch
relay due to looping errors (where the output port =
the input port). This only applies to switches."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.1;
Table 194 PortRcvErrorDetails::PortLoopingErrors."
::= { ibPmaPortRcvErrEntry 7 }
--****************************************************************
-- The Port Transmit Discard Details Table
--****************************************************************
ibPmaPortXmitDiscardTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortXmitDiscardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Transmit Discard details."
::= { ibPmaPortXmitRecvInfo 2 }
ibPmaPortXmitDiscardEntry OBJECT-TYPE
SYNTAX IbPmaPortXmitDiscardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortXmitDiscardTable containing
information about the transmit discard details for a
particular data port."
INDEX { ibPmaPortXmitDiscardIndex }
::= { ibPmaPortXmitDiscardTable 1 }
IbPmaPortXmitDiscardEntry ::= SEQUENCE {
ibPmaPortXmitDiscardIndex IbDataPort,
ibPmaPortInactiveDiscards Integer32,
ibPmaPortNeighborMtuDiscards Integer32,
ibPmaPortSwLifetimeLimitDiscards Integer32,
ibPmaPortSwHoqLimitDiscards Integer32
}
Expires August 2003 [Page 15]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortXmitDiscardIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortXmitDiscardEntry 1 }
ibPmaPortInactiveDiscards OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of outbound packets discarded by the port because
it is in the inactive state."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.2;
Table 195 PortXmitDisacrdDetails::PortInactiveDiscards."
::= { ibPmaPortXmitDiscardEntry 2 }
ibPmaPortNeighborMtuDiscards OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of outbound packets discarded by the port because
packet length exceeded the neighbor MTU."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.2;
Table 195 PortXmitDisacrdDetails::PortNeighborMTUDiscards."
::= { ibPmaPortXmitDiscardEntry 3 }
ibPmaPortSwLifetimeLimitDiscards OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of outbound packets discarded by the port because
the switch lifetime limit was exceeded. (This value is only
relevant for switches; otherwise the value should be 0)."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.2;
Table 195 PortXmitDisacrdDetails::PortSwLifetimeLimitDiscards."
::= { ibPmaPortXmitDiscardEntry 4 }
Expires August 2003 [Page 16]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortSwHoqLimitDiscards OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of outbound packets discarded by the port because
the switch HOQ lifetime was exceeded. (This object applies to
switches only. For other InfiniBand entities this should have
a value of 0)."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.2;
Table 195 PortXmitDisacrdDetails::PortSwHOQLimitDiscards."
::= { ibPmaPortXmitDiscardEntry 5 }
--****************************************************************
-- Port Flow Control Counters Table
--****************************************************************
ibPmaPortFlowCtlCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortXmitDiscardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Flow Control counters
information."
::= { ibPmaPortXmitRecvInfo 3 }
ibPmaPortFlowCtlCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortFlowCtlCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortFLowCtlCntrsTable containing
information about the flow control statistics for a particular
data port."
INDEX { ibPmaPortFlowCtlCntrsIndex }
::= { ibPmaPortFlowCtlCntrsTable 1 }
IbPmaPortFlowCtlCntrsEntry ::= SEQUENCE {
ibPmaPortFlowCtlCntrsIndex IbDataPort,
ibPmaPortFlowCtlXmitFlowPkts Integer32,
ibPmaPortFlowCtlRcvFlowPkts Integer32
}
ibPmaPortFlowCtlCntrsIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortFlowCtlCntrsEntry 1 }
Expires August 2003 [Page 17]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortFlowCtlXmitFlowPkts OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control packets transmitted on the port."
REFERENCE
"InfiniBand Architecture Release 1.1 Vol 1. Section 16.1.4.4;
Table 197 PortFlowCtlCounters::PortXmitFlowPkts."
::= { ibPmaPortFlowCtlCntrsEntry 2 }
ibPmaPortFlowCtlRcvFlowPkts OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control packets received on the port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.4;
Table 197 PortFlowCtlCounters::PortRcvFlowPkts."
::= { ibPmaPortFlowCtlCntrsEntry 3 }
--****************************************************************
-- Port Op Code Group
--
-- DESCRIPTION: This Group provides details for port statistics
-- indexed by op code and port number. This group contains
-- three tables: The Port Op Code Receive Counters Group, The
-- Port Op Code Virtual Lane Counters Group, and The Port Op
-- Code Virtual Lane Data Counters Group.
-- These three tables are optional.
--
-- NOTE: during operation, instead of "overflowing" these counters
-- stop at all 1's (until reset by the PMA).
--****************************************************************
ibPmaPortOpCodeInfo OBJECT IDENTIFIER ::= { ibPmaObjects 3 }
--****************************************************************
-- Port Op Code Receive Counters Group
--****************************************************************
ibPmaPortOpCodeRcvCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortOpCodeRcvCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Counters per Op Code information."
::= { ibPmaPortOpCodeInfo 1 }
Expires August 2003 [Page 18]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortOpCodeRcvCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortOpCodeRcvCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortOpCodeRcvCntrsTable containing
information about the receive counters per op code for a
particular data port."
INDEX { ibPmaPortOpCodeRcvCntrsPortIndex,
ibPmaPortOpCodeRcvCntrsIndex }
::= { ibPmaPortOpCodeRcvCntrsTable 1 }
IbPmaPortOpCodeRcvCntrsEntry ::= SEQUENCE {
ibPmaPortOpCodeRcvCntrsPortIndex IbDataPort,
ibPmaPortOpCodeRcvCntrsIndex Integer32,
ibPmaPortOpCodeRcvCntrsRcvPkts Counter32,
ibPmaPortOpCodeRcvCntrsRcvData Counter32
}
ibPmaPortOpCodeRcvCntrsPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortOpCodeRcvCntrsEntry 1 }
ibPmaPortOpCodeRcvCntrsIndex OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The op code for which this statistic is being reported.
Note: this is a 1-based value."
::= { ibPmaPortOpCodeRcvCntrsEntry 2 }
ibPmaPortOpCodeRcvCntrsRcvPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on this
port for this op code."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.3;
Table 196 PortOpRcvCounters::PortOpRcvPkts."
::= { ibPmaPortOpCodeRcvCntrsEntry 3 }
Expires August 2003 [Page 19]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortOpCodeRcvCntrsRcvData OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) received without
error for all VLs on this port for this op code. This includes
all octets between the start of packet delimeter and the VCRC,
exclusive. It excludes all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.3;
Table 196 PortOpRcvCounters::PortOpRcvData."
::= { ibPmaPortOpCodeRcvCntrsEntry 4 }
--****************************************************************
-- Port Op Code Virtual Lane Counters Group
--****************************************************************
ibPmaPortOpCodeVlCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortOpCodeVlCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port virtual lane op code information."
::= { ibPmaPortOpCodeInfo 2 }
ibPmaPortOpCodeVlCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortOpCodeVlCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortOpCodeVlCntrsTable containing
information about the virtual lane statistics for a particular
data port based on op code."
INDEX { ibPmaPortOpCodeVlCntrsPortIndex,
ibPmaPortOpCodeVlCntrsIndex }
::= { ibPmaPortOpCodeVlCntrsTable 1 }
IbPmaPortOpCodeVlCntrsEntry ::= SEQUENCE {
ibPmaPortOpCodeVlCntrsPortIndex IbDataPort,
ibPmaPortOpCodeVlCntrsIndex Integer32,
ibPmaPortVlOpPkt0 Integer32,
ibPmaPortVlOpPkt1 Integer32,
ibPmaPortVlOpPkt2 Integer32,
ibPmaPortVlOpPkt3 Integer32,
ibPmaPortVlOpPkt4 Integer32,
ibPmaPortVlOpPkt5 Integer32,
ibPmaPortVlOpPkt6 Integer32,
ibPmaPortVlOpPkt7 Integer32,
ibPmaPortVlOpPkt8 Integer32,
ibPmaPortVlOpPkt9 Integer32,
ibPmaPortVlOpPkt10 Integer32,
ibPmaPortVlOpPkt11 Integer32,
Expires August 2003 [Page 20]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt12 Integer32,
ibPmaPortVlOpPkt13 Integer32,
ibPmaPortVlOpPkt14 Integer32,
ibPmaPortVlOpPkt15 Integer32
}
ibPmaPortOpCodeVlCntrsPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortOpCodeVlCntrsEntry 1 }
ibPmaPortOpCodeVlCntrsIndex OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The op code for which this statistic is being reported.
Note: this is a 1-based value."
::= { ibPmaPortOpCodeVlCntrsEntry 2 }
ibPmaPortVlOpPkt0 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 0."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket0."
::= { ibPmaPortOpCodeVlCntrsEntry 3 }
ibPmaPortVlOpPkt1 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 1."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket1."
::= { ibPmaPortOpCodeVlCntrsEntry 4 }
Expires August 2003 [Page 21]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt2 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 2."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket2."
::= { ibPmaPortOpCodeVlCntrsEntry 5 }
ibPmaPortVlOpPkt3 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 3."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket3."
::= { ibPmaPortOpCodeVlCntrsEntry 6 }
ibPmaPortVlOpPkt4 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 4."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket4."
::= { ibPmaPortOpCodeVlCntrsEntry 7 }
ibPmaPortVlOpPkt5 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 5."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket5."
::= { ibPmaPortOpCodeVlCntrsEntry 8 }
Expires August 2003 [Page 22]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt6 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 6."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket6."
::= { ibPmaPortOpCodeVlCntrsEntry 9 }
ibPmaPortVlOpPkt7 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 7."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket7."
::= { ibPmaPortOpCodeVlCntrsEntry 10 }
ibPmaPortVlOpPkt8 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 8."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket8."
::= { ibPmaPortOpCodeVlCntrsEntry 11 }
ibPmaPortVlOpPkt9 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 9."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket9."
::= { ibPmaPortOpCodeVlCntrsEntry 12 }
Expires August 2003 [Page 23]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt10 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 10."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket10."
::= { ibPmaPortOpCodeVlCntrsEntry 13 }
ibPmaPortVlOpPkt11 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 11."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket11."
::= { ibPmaPortOpCodeVlCntrsEntry 14 }
ibPmaPortVlOpPkt12 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 12."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket12."
::= { ibPmaPortOpCodeVlCntrsEntry 15 }
ibPmaPortVlOpPkt13 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 13."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket13."
::= { ibPmaPortOpCodeVlCntrsEntry 16 }
Expires August 2003 [Page 24]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt14 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 14."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket14."
::= { ibPmaPortOpCodeVlCntrsEntry 17 }
ibPmaPortVlOpPkt15 OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received without error on the port
using this op code for Virtual Lane 15."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.5;
Table 198 PortVLOpPackets::PortVLOpPacket15."
::= { ibPmaPortOpCodeVlCntrsEntry 18 }
--****************************************************************
-- Port Op Code Virtual Lane Data Counters Table
--****************************************************************
ibPmaPortOpCodeVlDataCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortOpCodeVlCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port virtual lane op code information
about the number of data octets received without error."
::= { ibPmaPortOpCodeInfo 3 }
ibPmaPortOpCodeVlDataCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortOpCodeVlDataCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortCntrsTable containing
information about the basic performance and exception
statistics for a particular data port."
INDEX { ibPmaPortOpCodeVlDataPortIndex,
ibPmaPortOpCodeVlDataIndex }
::= { ibPmaPortOpCodeVlDataCntrsTable 1 }
IbPmaPortOpCodeVlDataCntrsEntry ::= SEQUENCE {
ibPmaPortOpCodeVlDataPortIndex IbDataPort,
ibPmaPortOpCodeVlDataIndex Integer32,
ibPmaPortVlOpData0 Counter32,
Expires August 2003 [Page 25]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData1 Counter32,
ibPmaPortVlOpData2 Counter32,
ibPmaPortVlOpData3 Counter32,
ibPmaPortVlOpData4 Counter32,
ibPmaPortVlOpData5 Counter32,
ibPmaPortVlOpData6 Counter32,
ibPmaPortVlOpData7 Counter32,
ibPmaPortVlOpData8 Counter32,
ibPmaPortVlOpData9 Counter32,
ibPmaPortVlOpData10 Counter32,
ibPmaPortVlOpData11 Counter32,
ibPmaPortVlOpData12 Counter32,
ibPmaPortVlOpData13 Counter32,
ibPmaPortVlOpData14 Counter32,
ibPmaPortVlOpData15 Counter32
}
ibPmaPortOpCodeVlDataPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortOpCodeVlDataCntrsEntry 1 }
ibPmaPortOpCodeVlDataIndex OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The op code for which this statistic is being reported.
Note: this is a 1-based value."
::= { ibPmaPortOpCodeVlDataCntrsEntry 2 }
ibPmaPortVlOpData0 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 0 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData0."
::= { ibPmaPortOpCodeVlDataCntrsEntry 3 }
Expires August 2003 [Page 26]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData1 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 1 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData1."
::= { ibPmaPortOpCodeVlDataCntrsEntry 4 }
ibPmaPortVlOpData2 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 2 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData2."
::= { ibPmaPortOpCodeVlDataCntrsEntry 5 }
ibPmaPortVlOpData3 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 3 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData3."
::= { ibPmaPortOpCodeVlDataCntrsEntry 6 }
Expires August 2003 [Page 27]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData4 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 4 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData4."
::= { ibPmaPortOpCodeVlDataCntrsEntry 7 }
ibPmaPortVlOpData5 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 5 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData5."
::= { ibPmaPortOpCodeVlDataCntrsEntry 8 }
ibPmaPortVlOpData6 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 6 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData6."
::= { ibPmaPortOpCodeVlDataCntrsEntry 9 }
Expires August 2003 [Page 28]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData7 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 7 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData7."
::= { ibPmaPortOpCodeVlDataCntrsEntry 10 }
ibPmaPortVlOpData8 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 8 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData8."
::= { ibPmaPortOpCodeVlDataCntrsEntry 11 }
ibPmaPortVlOpData9 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 9 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData9."
::= { ibPmaPortOpCodeVlDataCntrsEntry 12 }
Expires August 2003 [Page 29]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData10 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 10 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData10."
::= { ibPmaPortOpCodeVlDataCntrsEntry 13 }
ibPmaPortVlOpData11 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 11 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData11."
::= { ibPmaPortOpCodeVlDataCntrsEntry 14 }
ibPmaPortVlOpData12 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 12 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData12."
::= { ibPmaPortOpCodeVlDataCntrsEntry 15 }
Expires August 2003 [Page 30]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpData13 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 13 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData13."
::= { ibPmaPortOpCodeVlDataCntrsEntry 16 }
ibPmaPortVlOpData14 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 14 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData14."
::= { ibPmaPortOpCodeVlDataCntrsEntry 17 }
ibPmaPortVlOpData15 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of data octets (divided by 4) that were received on
VL 15 for this port and op code. This count includes all octets
between the start of the packet and VCRC, exclusive. It excludes
all link packets."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 199 PortVLOpData::PortVLOpData15."
::= { ibPmaPortOpCodeVlDataCntrsEntry 18 }
Expires August 2003 [Page 31]
Internet-Draft IPOVERIB PMA MIB February 2003
--****************************************************************
-- Port Virtual Lane Group
--
-- DESCRIPTION: This Group provides details for port statistics
-- indexed by the virtual lane within the port. This group
-- contains three tables: The Port Virtual Lane Transmit Flow
-- Control Error Table, The Port Virtual Lane Transmit Wait
-- Counters Table, and The Port Virtual Lane Software Congestion
-- Table.
-- These three tables are optional.
--
-- NOTE: during operation, instead of "overflowing" these counters
-- stop at all 1's (until reset by the PMA).
--****************************************************************
ibPmaPortVlInfo OBJECT IDENTIFIER ::= { ibPmaObjects 4 }
--****************************************************************
-- Port Virtual Lane Transmit Flow Control Error Table
--****************************************************************
ibPmaPortVlXmitFCUpErrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Virtual Lane Flow Control update
errors for a particular port."
::= { ibPmaPortVlInfo 1 }
ibPmaPortVlXmitFCUpErrEntry OBJECT-TYPE
SYNTAX IbPmaPortVlXmitFCUpErrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortVlXmitFCUpErrTable containing
information about the transmit flow control error
statistics for the virtual lanes on a particular data port."
INDEX { ibPmaPortVlXmitFCUpErrPortIndex }
::= { ibPmaPortVlXmitFCUpErrTable 1 }
IbPmaPortVlXmitFCUpErrEntry ::= SEQUENCE {
ibPmaPortVlXmitFCUpErrPortIndex IbDataPort,
ibPmaPortVlXmitFCUpErr0 Integer32,
ibPmaPortVlXmitFCUpErr1 Integer32,
ibPmaPortVlXmitFCUpErr2 Integer32,
ibPmaPortVlXmitFCUpErr3 Integer32,
ibPmaPortVlXmitFCUpErr4 Integer32,
ibPmaPortVlXmitFCUpErr5 Integer32,
ibPmaPortVlXmitFCUpErr6 Integer32,
ibPmaPortVlXmitFCUpErr7 Integer32,
ibPmaPortVlXmitFCUpErr8 Integer32,
ibPmaPortVlXmitFCUpErr9 Integer32,
Expires August 2003 [Page 32]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr10 Integer32,
ibPmaPortVlXmitFCUpErr11 Integer32,
ibPmaPortVlXmitFCUpErr12 Integer32,
ibPmaPortVlXmitFCUpErr13 Integer32,
ibPmaPortVlXmitFCUpErr14 Integer32,
ibPmaPortVlXmitFCUpErr15 Integer32
}
ibPmaPortVlXmitFCUpErrPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortVlXmitFCUpErrEntry 1 }
ibPmaPortVlXmitFCUpErr0 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 0 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors0."
::= { ibPmaPortVlXmitFCUpErrEntry 2 }
ibPmaPortVlXmitFCUpErr1 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 1 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors1."
::= { ibPmaPortVlXmitFCUpErrEntry 3 }
Expires August 2003 [Page 33]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr2 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 2 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors2."
::= { ibPmaPortVlXmitFCUpErrEntry 4 }
ibPmaPortVlXmitFCUpErr3 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 3 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors3."
::= { ibPmaPortVlXmitFCUpErrEntry 5 }
ibPmaPortVlXmitFCUpErr4 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 4 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors4."
::= { ibPmaPortVlXmitFCUpErrEntry 6 }
ibPmaPortVlXmitFCUpErr5 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 5 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors5."
::= { ibPmaPortVlXmitFCUpErrEntry 7 }
Expires August 2003 [Page 34]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr6 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 6 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors6."
::= { ibPmaPortVlXmitFCUpErrEntry 8 }
ibPmaPortVlXmitFCUpErr7 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 7 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors7."
::= { ibPmaPortVlXmitFCUpErrEntry 9 }
ibPmaPortVlXmitFCUpErr8 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 8 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors8."
::= { ibPmaPortVlXmitFCUpErrEntry 10 }
ibPmaPortVlXmitFCUpErr9 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 9 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors9."
::= { ibPmaPortVlXmitFCUpErrEntry 11 }
Expires August 2003 [Page 35]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr10 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 10 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors10."
::= { ibPmaPortVlXmitFCUpErrEntry 12 }
ibPmaPortVlXmitFCUpErr11 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 11 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors11."
::= { ibPmaPortVlXmitFCUpErrEntry 13 }
ibPmaPortVlXmitFCUpErr12 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 12 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors12."
::= { ibPmaPortVlXmitFCUpErrEntry 14 }
ibPmaPortVlXmitFCUpErr13 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 13 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors13."
::= { ibPmaPortVlXmitFCUpErrEntry 15 }
Expires August 2003 [Page 36]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr14 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 14 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors14."
::= { ibPmaPortVlXmitFCUpErrEntry 16 }
ibPmaPortVlXmitFCUpErr15 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of flow control update errors on VL 15 for
this port."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1.
Section 16.1.4.7; Table 200
PortVLXmitFlowCtlUpdateErrors::PortVLXmitFlowCtlUpdateErrors15."
::= { ibPmaPortVlXmitFCUpErrEntry 17 }
--****************************************************************
-- Port Virtual Lane Transmit Wait Counters Table
--****************************************************************
ibPmaPortVlXmitWaitCntrsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortVlXmitWaitCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Virtual Lane Tranmsit Wait Counters
information."
::= { ibPmaPortVlInfo 2 }
ibPmaPortVlXmitWaitCntrsEntry OBJECT-TYPE
SYNTAX IbPmaPortVlXmitWaitCntrsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortVlXmitWaitCntrsTable
containing information about the transmit wait counters for
a virtual lane for a particular data port."
INDEX { ibPmaPortVlXmitWaitCntrsIndex }
::= { ibPmaPortVlXmitWaitCntrsTable 1 }
IbPmaPortVlXmitWaitCntrsEntry ::= SEQUENCE {
ibPmaPortVlXmitWaitCntrsIndex IbDataPort,
ibPmaPortVlXmitWait0 Integer32,
Expires August 2003 [Page 37]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitWait1 Integer32,
ibPmaPortVlXmitWait2 Integer32,
ibPmaPortVlXmitWait3 Integer32,
ibPmaPortVlXmitWait4 Integer32,
ibPmaPortVlXmitWait5 Integer32,
ibPmaPortVlXmitWait6 Integer32,
ibPmaPortVlXmitWait7 Integer32,
ibPmaPortVlXmitWait8 Integer32,
ibPmaPortVlXmitWait9 Integer32,
ibPmaPortVlXmitWait10 Integer32,
ibPmaPortVlXmitWait11 Integer32,
ibPmaPortVlXmitWait12 Integer32,
ibPmaPortVlXmitWait13 Integer32,
ibPmaPortVlXmitWait14 Integer32,
ibPmaPortVlXmitWait15 Integer32
}
ibPmaPortVlXmitWaitCntrsIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortVlXmitWaitCntrsEntry 1 }
ibPmaPortVlXmitWait0 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL0 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait0."
::= { ibPmaPortVlXmitWaitCntrsEntry 2 }
ibPmaPortVlXmitWait1 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL1 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait1."
::= { ibPmaPortVlXmitWaitCntrsEntry 3 }
Expires August 2003 [Page 38]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitWait2 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL2 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait2."
::= { ibPmaPortVlXmitWaitCntrsEntry 4 }
ibPmaPortVlXmitWait3 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL3 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait3."
::= { ibPmaPortVlXmitWaitCntrsEntry 5 }
ibPmaPortVlXmitWait4 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL4 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait4."
::= { ibPmaPortVlXmitWaitCntrsEntry 6 }
ibPmaPortVlXmitWait5 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL5 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait5."
::= { ibPmaPortVlXmitWaitCntrsEntry 7 }
Expires August 2003 [Page 39]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitWait6 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL6 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait6."
::= { ibPmaPortVlXmitWaitCntrsEntry 8 }
ibPmaPortVlXmitWait7 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL7 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait7."
::= { ibPmaPortVlXmitWaitCntrsEntry 9 }
ibPmaPortVlXmitWait8 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL8 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait8."
::= { ibPmaPortVlXmitWaitCntrsEntry 10 }
ibPmaPortVlXmitWait9 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL9 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait9."
::= { ibPmaPortVlXmitWaitCntrsEntry 11 }
Expires August 2003 [Page 40]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitWait10 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL10 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait10."
::= { ibPmaPortVlXmitWaitCntrsEntry 12 }
ibPmaPortVlXmitWait11 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL11 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait11."
::= { ibPmaPortVlXmitWaitCntrsEntry 13 }
ibPmaPortVlXmitWait12 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL12 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait12."
::= { ibPmaPortVlXmitWaitCntrsEntry 14 }
ibPmaPortVlXmitWait13 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL13 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait13."
::= { ibPmaPortVlXmitWaitCntrsEntry 15 }
Expires August 2003 [Page 41]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitWait14 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL14 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait14."
::= { ibPmaPortVlXmitWaitCntrsEntry 16 }
ibPmaPortVlXmitWait15 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of ticks during which the port had data to transmit
on VL15 but no data was sent during the entire tick either because
of insufficient credits or because of lack of arbitration."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.4.6;
Table 201 PortVLXmitWaitCounters::PortVLXmitWait15."
::= { ibPmaPortVlXmitWaitCntrsEntry 17 }
--****************************************************************
-- Port Virtual Lane Software Congestion Table
--****************************************************************
ibPmaPortVlSwCongestionTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPmaPortVlSwCongestionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing PMA Port Virtual Lane Software Congestion
information."
::= { ibPmaPortVlInfo 3 }
ibPmaPortVlSwCongestionEntry OBJECT-TYPE
SYNTAX IbPmaPortVlSwCongestionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPmaPortVlSwCongestionTable
containing information about the software congestion per
virtual lane for a particular data port."
INDEX { ibPmaPortVlSwCongestionIndex }
::= { ibPmaPortVlSwCongestionTable 1 }
IbPmaPortVlSwCongestionEntry ::= SEQUENCE {
ibPmaPortVlSwCongestionIndex IbDataPort,
ibPmaPortVlSwCongestion0 Integer32,
Expires August 2003 [Page 42]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion1 Integer32,
ibPmaPortVlSwCongestion2 Integer32,
ibPmaPortVlSwCongestion3 Integer32,
ibPmaPortVlSwCongestion4 Integer32,
ibPmaPortVlSwCongestion5 Integer32,
ibPmaPortVlSwCongestion6 Integer32,
ibPmaPortVlSwCongestion7 Integer32,
ibPmaPortVlSwCongestion8 Integer32,
ibPmaPortVlSwCongestion9 Integer32,
ibPmaPortVlSwCongestion10 Integer32,
ibPmaPortVlSwCongestion11 Integer32,
ibPmaPortVlSwCongestion12 Integer32,
ibPmaPortVlSwCongestion13 Integer32,
ibPmaPortVlSwCongestion14 Integer32,
ibPmaPortVlSwCongestion15 Integer32
}
ibPmaPortVlSwCongestionIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port. The IBA
defines a range of valid data ports from 1 to N, where
N can have a maximum value of 254."
::= { ibPmaPortVlSwCongestionEntry 1 }
ibPmaPortVlSwCongestion0 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 0 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion0."
::= { ibPmaPortVlSwCongestionEntry 2 }
Expires August 2003 [Page 43]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion1 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 1 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion1."
::= { ibPmaPortVlSwCongestionEntry 3 }
ibPmaPortVlSwCongestion2 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 2 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion2."
::= { ibPmaPortVlSwCongestionEntry 4 }
ibPmaPortVlSwCongestion3 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 3 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion3."
::= { ibPmaPortVlSwCongestionEntry 5 }
Expires August 2003 [Page 44]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion4 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 4 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion4."
::= { ibPmaPortVlSwCongestionEntry 6 }
ibPmaPortVlSwCongestion5 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 5 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion5."
::= { ibPmaPortVlSwCongestionEntry 7 }
ibPmaPortVlSwCongestion6 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 6 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion6."
::= { ibPmaPortVlSwCongestionEntry 8 }
Expires August 2003 [Page 45]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion7 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 7 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion7."
::= { ibPmaPortVlSwCongestionEntry 9 }
ibPmaPortVlSwCongestion8 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 8 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion8."
::= { ibPmaPortVlSwCongestionEntry 10 }
ibPmaPortVlSwCongestion9 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 9 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion9."
::= { ibPmaPortVlSwCongestionEntry 11 }
Expires August 2003 [Page 46]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion10 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 10 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion10."
::= { ibPmaPortVlSwCongestionEntry 12 }
ibPmaPortVlSwCongestion11 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 11 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion11."
::= { ibPmaPortVlSwCongestionEntry 13 }
ibPmaPortVlSwCongestion12 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 12 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion12."
::= { ibPmaPortVlSwCongestionEntry 14 }
Expires August 2003 [Page 47]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion13 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 13 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion13."
::= { ibPmaPortVlSwCongestionEntry 15 }
ibPmaPortVlSwCongestion14 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 14 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion14."
::= { ibPmaPortVlSwCongestionEntry 16 }
ibPmaPortVlSwCongestion15 OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets to be transmitted on VL 15 for
this output port that were discarded because of congestion.
This includes the following reasons
- Switch lifetime limit exceeded
- Switch HOQ limit exceeded."
REFERENCE
"InfiniBand Architecture Release 1.1. Vol 1. Section 16.1.3.5;
Table 202 SwPortVLCongestion::SWPortVLCongestion15."
::= { ibPmaPortVlSwCongestionEntry 17 }
--****************************************************************
-- Module Conformance Statement
--
-- DESCRIPTION: The module conformance statement includes the
-- compliance statements and the units of conformance
-- section.
--****************************************************************
Expires August 2003 [Page 48]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaCompliances OBJECT IDENTIFIER ::= { ibPmaConformance 1 }
ibPmaGroups OBJECT IDENTIFIER ::= { ibPmaConformance 2 }
--****************************************************************
-- Compliance Statements
--****************************************************************
ibPmaBasicNodeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The basic node implementation requirements for agents that
support the IPOIB PMA MIB."
MODULE -- this module
MANDATORY-GROUPS {
ibPmaPortCntrsMandatoryGroup
}
::= { ibPmaCompliances 1 }
ibPmaFullNodeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The full node implementation requirements for agents that
support the IPOIB PMA MIB. This include all of the optional
counter groups"
MODULE -- this module
MANDATORY-GROUPS {
ibPmaPortCntrsMandatoryGroup,
ibPmaPortCntrsOptionalGroup,
ibPmaPortRcvErrGroup,
ibPmaPortXmitDiscardGroup,
ibPmaPortFlowCtlCntrsGroup,
ibPmaPortOpCodeRcvCntrsGroup,
ibPmaPortOpCodeVlCntrsGroup,
ibPmaPortOpCodeVlDataCntrsGroup,
ibPmaPortVlXmitFCUpErrGroup,
ibPmaPortVlXmitWaitGroup,
ibPmaPortVlSwCongestionGroup
}
::= { ibPmaCompliances 2 }
--****************************************************************
-- Units Of Conformance
--****************************************************************
ibPmaPortCntrsMandatoryGroup OBJECT-GROUP
OBJECTS {
ibPmaSymbolErrCounter,
ibPmaLinkErrRecoveryCntr,
ibPmaLinkDownedCntr,
ibPmaPortRcvErr,
ibPmaPortRcvRemPhysErr,
ibPmaPortRcvSwitchRelayErr,
Expires August 2003 [Page 49]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortXmitDiscard,
ibPmaPortXmitConstraintErr,
ibPmaPortRcvConstraintErr,
ibPmaLocalLinkIntegrityErr,
ibPmaExcessBufOverrunErr,
ibPmaVl15Dropped
}
STATUS current
DESCRIPTION
"The ibPmaPortCntrsMandatoryGroup defines the MIB objects that
describe the mandatory counters that must be maintained by the
Performance Management Agent."
::= { ibPmaGroups 1 }
ibPmaPortCntrsOptionalGroup OBJECT-GROUP
OBJECTS {
ibPmaPortXmitData,
ibPmaPortRcvData,
ibPmaPortXmitPkts,
ibPmaPortRcvPkts
}
STATUS current
DESCRIPTION
"The ibPmaPortCntrsOptionalGroup defines the MIB objects that
describe the optional counters that must be maintained by the
Performance Management Agent."
::= { ibPmaGroups 2 }
ibPmaPortRcvErrGroup OBJECT-GROUP
OBJECTS {
ibPmaPortRcvErrLocalPhysErrs,
ibPmaPortMalformedPacketErrs,
ibPmaPortBufferOverrunErrs,
ibPmaPortDLIDMappingErrs,
ibPmaPortVLMappingErrs,
ibPmaPortLoopingErrs
}
STATUS current
DESCRIPTION
"The ibPmaPortRcvErrGroup defines the MIB objects that describe
the receive error counters for a particular port by the PMA."
::= { ibPmaGroups 3 }
Expires August 2003 [Page 50]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortXmitDiscardGroup OBJECT-GROUP
OBJECTS {
ibPmaPortInactiveDiscards,
ibPmaPortNeighborMtuDiscards,
ibPmaPortSwLifetimeLimitDiscards,
ibPmaPortSwHoqLimitDiscards
}
STATUS current
DESCRIPTION
"The ibPmaPortXmitDiscardGroup defines the MIB objects that
describe the transmit discard details for a particular port
by the PMA."
::= { ibPmaGroups 4 }
ibPmaPortFlowCtlCntrsGroup OBJECT-GROUP
OBJECTS {
ibPmaPortFlowCtlXmitFlowPkts,
ibPmaPortFlowCtlRcvFlowPkts
}
STATUS current
DESCRIPTION
"The ibPmaPortFlowCtlCntrsGroup defines the MIB objects that
describe the transmit and receive flow control counters for
a particular port by the PMA."
::= { ibPmaGroups 5 }
ibPmaPortOpCodeRcvCntrsGroup OBJECT-GROUP
OBJECTS {
ibPmaPortOpCodeRcvCntrsRcvPkts,
ibPmaPortOpCodeRcvCntrsRcvData
}
STATUS current
DESCRIPTION
"The ibPmaPortOpCodeRcvCntrsGroup defines the MIB objects that
describe the receive counters for a particular port and op
code by the PMA."
::= { ibPmaGroups 6 }
ibPmaPortOpCodeVlCntrsGroup OBJECT-GROUP
OBJECTS {
ibPmaPortVlOpPkt0,
ibPmaPortVlOpPkt1,
ibPmaPortVlOpPkt2,
ibPmaPortVlOpPkt3,
ibPmaPortVlOpPkt4,
ibPmaPortVlOpPkt5,
ibPmaPortVlOpPkt6,
ibPmaPortVlOpPkt7,
ibPmaPortVlOpPkt8,
ibPmaPortVlOpPkt9,
ibPmaPortVlOpPkt10,
ibPmaPortVlOpPkt11,
ibPmaPortVlOpPkt12,
Expires August 2003 [Page 51]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlOpPkt13,
ibPmaPortVlOpPkt14,
ibPmaPortVlOpPkt15
}
STATUS current
DESCRIPTION
"The ibPmaPortOpCodeVlCntrsGroup defines the MIB objects that
describe the packet counters for a particular port, op code,
and virtual lane by the PMA."
::= { ibPmaGroups 7 }
ibPmaPortOpCodeVlDataCntrsGroup OBJECT-GROUP
OBJECTS {
ibPmaPortVlOpData0,
ibPmaPortVlOpData1,
ibPmaPortVlOpData2,
ibPmaPortVlOpData3,
ibPmaPortVlOpData4,
ibPmaPortVlOpData5,
ibPmaPortVlOpData6,
ibPmaPortVlOpData7,
ibPmaPortVlOpData8,
ibPmaPortVlOpData9,
ibPmaPortVlOpData10,
ibPmaPortVlOpData11,
ibPmaPortVlOpData12,
ibPmaPortVlOpData13,
ibPmaPortVlOpData14,
ibPmaPortVlOpData15
}
STATUS current
DESCRIPTION
"The ibPmaPortOpCodeVlDataCntrsGroup defines the MIB objects that
describe the octet counters for a particular port, op code, and
virtual lane by the PMA."
::= { ibPmaGroups 8 }
ibPmaPortVlXmitFCUpErrGroup OBJECT-GROUP
OBJECTS {
ibPmaPortVlXmitFCUpErr0,
ibPmaPortVlXmitFCUpErr1,
ibPmaPortVlXmitFCUpErr2,
ibPmaPortVlXmitFCUpErr3,
ibPmaPortVlXmitFCUpErr4,
ibPmaPortVlXmitFCUpErr5,
ibPmaPortVlXmitFCUpErr6,
ibPmaPortVlXmitFCUpErr7,
ibPmaPortVlXmitFCUpErr8,
ibPmaPortVlXmitFCUpErr9,
ibPmaPortVlXmitFCUpErr10,
ibPmaPortVlXmitFCUpErr11,
ibPmaPortVlXmitFCUpErr12,
ibPmaPortVlXmitFCUpErr13,
Expires August 2003 [Page 52]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlXmitFCUpErr14,
ibPmaPortVlXmitFCUpErr15
}
STATUS current
DESCRIPTION
"The ibPmaPortVlXmitFCUpErrGroup defines the MIB objects that
describe the transmit flow control update counters for a
particular port and virtual lane by the PMA."
::= { ibPmaGroups 9 }
ibPmaPortVlXmitWaitGroup OBJECT-GROUP
OBJECTS {
ibPmaPortVlXmitWait0,
ibPmaPortVlXmitWait1,
ibPmaPortVlXmitWait2,
ibPmaPortVlXmitWait3,
ibPmaPortVlXmitWait4,
ibPmaPortVlXmitWait5,
ibPmaPortVlXmitWait6,
ibPmaPortVlXmitWait7,
ibPmaPortVlXmitWait8,
ibPmaPortVlXmitWait9,
ibPmaPortVlXmitWait10,
ibPmaPortVlXmitWait11,
ibPmaPortVlXmitWait12,
ibPmaPortVlXmitWait13,
ibPmaPortVlXmitWait14,
ibPmaPortVlXmitWait15
}
STATUS current
DESCRIPTION
"The ibPmaPortVlXmitWaitGroup defines the MIB objects that
describe the transmit wait counters for a particular port
and virtual lane by the PMA."
::= { ibPmaGroups 10 }
ibPmaPortVlSwCongestionGroup OBJECT-GROUP
OBJECTS {
ibPmaPortVlSwCongestion0,
ibPmaPortVlSwCongestion1,
ibPmaPortVlSwCongestion2,
ibPmaPortVlSwCongestion3,
ibPmaPortVlSwCongestion4,
ibPmaPortVlSwCongestion5,
ibPmaPortVlSwCongestion6,
ibPmaPortVlSwCongestion7,
ibPmaPortVlSwCongestion8,
ibPmaPortVlSwCongestion9,
ibPmaPortVlSwCongestion10,
ibPmaPortVlSwCongestion11,
ibPmaPortVlSwCongestion12,
ibPmaPortVlSwCongestion13,
ibPmaPortVlSwCongestion14,
Expires August 2003 [Page 53]
Internet-Draft IPOVERIB PMA MIB February 2003
ibPmaPortVlSwCongestion15
}
STATUS current
DESCRIPTION
"The ibPmaPortVlSwCongestionGroup defines the MIB objects that
describe the software congestion counters for a particular port
and virtual lane by the PMA."
::= { ibPmaGroups 11 }
END
6. Security Considerations
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET
(change/create/delete) them.
7. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; neither does it
represent that it has made any effort to identify any such
rights. Information on the IETF's procedures with respect to
rights in standards-track and standards-related documentation
can be found in BCP-11. Copies of claims of rights made
available for publication and any assurances of licenses to be
made available, or the result of an attempt made to obtain a
general license or permission for the use of such proprietary
rights by implementors or users of this specification can be
obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights which may cover technology that may be required
to practice this standard. Please address the information to the
IETF Executive Director.
Expires August 2003 [Page 54]
Internet-Draft IPOVERIB PMA MIB February 2003
8. References
[RFC2571] Harrington, D., Presuhn, R. and B. Wijnen, "An
Architecture for Describing SNMP Management Frameworks",
RFC 2571, April 1999.
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991.
[RFC1215] Rose, M., "A Convention for Defining Traps for use with
the SNMP", RFC 1215, March 1991.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901,
January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R. and B. Wijnen,
"Message Processing and Dispatching for the Simple Network
Management Protocol (SNMP)", RFC 2572, April 1999.
[RFC2574] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC2573] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications",
Expires August 2003 [Page 55]
Internet-Draft IPOVERIB PMA MIB February 2003
RFC 2573, April 1999.
[RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2570] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction to Version 3 of the Internet-standard
Network Management Framework", RFC 2570, April 1999.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[IBTAArch] Infiniband Trade Association, Infiniband(TM)
Architecture Specification Vol 1 & 2 Release 1.1,
November 6, 2002.
[IBIF] Anderson, B., and S. Harnedy, "Definition of Managed Objects
Infiniband Interface Types" <draft-ietf-ipoib-ibif-mib-04.txt>,
January 2003.
[IBTC] Harnedy, S., "Definition of Textual Conventions and OBJECT-
IDENTITIES for IP Over InfiniBand (IPOVERIB) Management"
<draft-ietf-ipoib-ibmib-tc-mib-02.txt>. January 2003.
9. Author's Address
Sean Harnedy
InfiniSwitch Corporation
134 Flanders Road Phone: 1-508-599-6388
Westborough, MA 01581 Email: sharnedy@infiniswitch.com
USA
Expires August 2003 [Page 56]
