Network Working Group G. Fioccola, Ed.
Internet-Draft Huawei Technologies
Obsoletes: 8889 (if approved) M. Cociglio
Intended status: Standards Track Telecom Italia
Expires: December 9, 2022 A. Sapio
Intel Corporation
R. Sisto
Politecnico di Torino
T. Zhou
Huawei Technologies
June 7, 2022
Multipoint Alternate-Marking Clustered Method
draft-ietf-ippm-rfc8889bis-02
Abstract
This document generalizes and expands Alternate-Marking methodology
to measure any kind of unicast flow whose packets can follow several
different paths in the network -- in wider terms, a multipoint-to-
multipoint network. For this reason, the technique here described is
called "Multipoint Alternate Marking". This document obsoletes
RFC8889.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 9, 2022.
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
Fioccola, et al. Expires December 9, 2022 [Page 1]
Internet-Draft ClustAltMark June 2022
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Summary of Changes from RFC 8889 . . . . . . . . . . . . 5
1.2. Requirements Language . . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1. Correlation with RFC 5644 . . . . . . . . . . . . . . . . 6
3. Flow Classification . . . . . . . . . . . . . . . . . . . . . 7
4. Extension of the Method to Multipoint Flows . . . . . . . . . 9
4.1. Monitoring Network . . . . . . . . . . . . . . . . . . . 10
4.2. Network Packet Loss . . . . . . . . . . . . . . . . . . . 11
5. Network Clustering . . . . . . . . . . . . . . . . . . . . . 12
5.1. Algorithm for Clusters Partition . . . . . . . . . . . . 13
6. Multipoint Packet Loss Measurement . . . . . . . . . . . . . 17
7. Multipoint Delay and Delay Variation . . . . . . . . . . . . 17
7.1. Delay Measurements on a Multipoint-Paths Basis . . . . . 18
7.1.1. Single-Marking Measurement . . . . . . . . . . . . . 18
7.2. Delay Measurements on a Single-Packet Basis . . . . . . . 18
7.2.1. Single- and Double-Marking Measurement . . . . . . . 18
7.2.2. Hashing Selection Method . . . . . . . . . . . . . . 19
8. Synchronization and Timing . . . . . . . . . . . . . . . . . 20
9. Results of the Multipoint Alternate Marking Experiment . . . 22
10. A Closed-Loop Performance-Management Approach . . . . . . . . 23
11. Security Considerations . . . . . . . . . . . . . . . . . . . 24
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 24
13. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 24
14. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 25
15. References . . . . . . . . . . . . . . . . . . . . . . . . . 25
15.1. Normative References . . . . . . . . . . . . . . . . . . 25
15.2. Informative References . . . . . . . . . . . . . . . . . 25
Appendix A. Changes Log . . . . . . . . . . . . . . . . . . . . 26
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28
1. Introduction
The Alternate-Marking Method, as described in
[I-D.ietf-ippm-rfc8321bis], is applicable to a point-to-point path.
The extension proposed in this document applies to the most general
Fioccola, et al. Expires December 9, 2022 [Page 2]
Internet-Draft ClustAltMark June 2022
case of a multipoint-to-multipoint path and enables flexible and
adaptive performance measurements in a managed network.
The Alternate-Marking methodology described in
[I-D.ietf-ippm-rfc8321bis] allows the synchronization of the
measurements at different points by dividing the packet flow into
batches. So it is possible to get coherent counters and show what is
happening in every marking period for each monitored flow. The
monitoring parameters are the packet counter and timestamps of a flow
for each marking period. Note that additional details about the
applicability of the Alternate-Marking methodology are described in
[I-D.ietf-ippm-rfc8321bis] while implementation details can be found
in the paper "AM-PM: Efficient Network Telemetry using Alternate
Marking" [IEEE-Network-PNPM].
There are some applications of the Alternate-Marking method where
there are a lot of monitored flows and nodes. Multipoint Alternate
Marking aims to reduce these values and makes the performance
monitoring more flexible in case a detailed analysis is not needed.
For instance, by considering n measurement points and m monitored
flows, the order of magnitude of the packet counters for each time
interval is n*m*2 (1 per color). The number of measurement points
and monitored flows may vary and depends on the portion of the
network we are monitoring (core network, metro network, access
network) and the granularity (for each service, each customer). So
if both n and m are high values, the packet counters increase a lot,
and Multipoint Alternate Marking offers a tool to control these
parameters.
The approach presented in this document is applied only to unicast
flows and not to multicast. Broadcast, Unknown Unicast, and
Multicast (BUM) traffic is not considered here, because traffic
replication is not covered by the Multipoint Alternate-Marking
method. Furthermore, it can be applicable to anycast flows, and
Equal-Cost Multipath (ECMP) paths can also be easily monitored with
this technique.
[I-D.ietf-ippm-rfc8321bis] applies to point-to-point unicast flows
and BUM traffic. For BUM traffic, the basic method of
[I-D.ietf-ippm-rfc8321bis] can easily be applied link by link and
therefore split the multicast flow tree distribution into separate
unicast point-to-point links. While this document and its Clustered
Alternate-Marking method is valid for multipoint-to-multipoint
unicast flows, anycast, and ECMP flows.
Therefore, the Alternate-Marking method can be extended to any kind
of multipoint-to-multipoint paths, and the network-clustering
approach presented in this document is the formalization of how to
Fioccola, et al. Expires December 9, 2022 [Page 3]
Internet-Draft ClustAltMark June 2022
implement this property and allow a flexible and optimized
performance measurement support for network management in every
situation.
Without network clustering, it is possible to apply Alternate Marking
only for all the network or per single flow. Instead, with network
clustering, it is possible to use the partition of the network into
clusters at different levels in order to provide the needed degree of
detail. In some circumstances, it is possible to monitor a
multipoint network by monitoring the network clusters, without
examining in depth. In case of problems (packet loss is measured or
the delay is too high), the filtering criteria could be enhanced in
order to perform a detailed analysis by using a different combination
of clusters up to a per-flow measurement as described in
[I-D.ietf-ippm-rfc8321bis].
This approach fits very well with the Closed-Loop Network and
Software-Defined Network (SDN) paradigm, where the SDN orchestrator
and the SDN controllers are the brains of the network and can manage
flow control to the switches and routers and, in the same way, can
calibrate the performance measurements depending on the desired
accuracy. An SDN controller application can orchestrate how
accurately the network performance monitoring is set up by applying
the Multipoint Alternate Marking as described in this document.
It is important to underline that, as an extension of
[I-D.ietf-ippm-rfc8321bis], this is a methodology document, so the
mechanism that can be used to transmit the counters and the
timestamps is out of scope here, and the implementation is open.
Several options are possible -- e.g., see "Enhanced Alternate Marking
Method" [I-D.zhou-ippm-enhanced-alternate-marking].
This document assumes that the blocks are created according to a
fixed timer as per [I-D.ietf-ippm-rfc8321bis]. Switching after a
fixed number of packets is possible but it is out of scope here.
Note that the fragmented packets case can be managed with the
Alternate-Marking methodology. The same considerations of
[I-D.ietf-ippm-rfc8321bis] apply also in the case of Multipoint
Alternate Marking. As defined in [I-D.ietf-ippm-rfc8321bis] the
marking node MUST mark all the fragments except in the case of
fragmentation within the network domain, in that event it is
suggested to mark only the first fragment.
Fioccola, et al. Expires December 9, 2022 [Page 4]
Internet-Draft ClustAltMark June 2022
1.1. Summary of Changes from RFC 8889
This document defines the Multipoint Alternate-Marking Method,
addressing ambiguities and overtaking its experimental phase in the
original specification [RFC8889].
The relevant changes are:
o Added the recommendations about the different deployments in case
one or two flag bits are available for marking (Section 9).
o Changed the structure to improve the readability.
o Removed the wording about the experimentation of the method and
considerations that no longer apply.
o Revised the description of detailed aspects of the methodology,
e.g. synchronization and timing.
It is important to note that all the changes are totally backward
compatible with [RFC8889] and no new additional technique has been
introduced in this document compared to [RFC8889].
The detailed changes can be found in Appendix A.
1.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Terminology
The definitions of the basic terms are identical to those found in
Alternate Marking [I-D.ietf-ippm-rfc8321bis]. It is to be remembered
that [I-D.ietf-ippm-rfc8321bis] is valid for point-to-point unicast
flows and BUM traffic.
The important new terms that need to be explained are listed below:
Multipoint Alternate Marking: Extension to
[I-D.ietf-ippm-rfc8321bis], valid for multipoint-to-multipoint
unicast flows, anycast, and ECMP flows. It can also be referred
to as Clustered Alternate Marking.
Fioccola, et al. Expires December 9, 2022 [Page 5]
Internet-Draft ClustAltMark June 2022
Flow definition: The concept of flow is generalized in this
document. The identification fields are selected without any
constraints and, in general, the flow can be a multipoint-to-
multipoint flow, as a result of aggregate point-to-point flows.
Monitoring Network: Identified with the nodes of the network that
are the measurement points (MPs) and the links that are the
connections between MPs. The monitoring network graph depends on
the flow definition, so it can represent a specific flow or the
entire network topology as aggregate of all the flows. Each node
of the monitoring network cannot be both a source and a
destination of the flow.
Cluster: Smallest identifiable subnetwork of the entire monitoring
network graph that still satisfies the condition that the number
of packets that go in is the same as the number that go out. A
cluster partition algorithm can be applied to split the monitoring
network into clusters.
Multipoint metrics: Packet loss, delay and delay variation are
extended to the case of multipoint flows. It is possible to
compute these metrics on the basis of multipoint paths in order to
associate the measurements to a cluster, a combination of
clusters, or the entire monitored network. For delay and delay
variation, it is also possible to define the metrics on a single-
packet basis, and it means that the multipoint path is used to
easily couple packets between input and output nodes of a
multipoint path.
The next section highlights the correlation with the terms used in
RFC 5644 [RFC5644].
2.1. Correlation with RFC 5644
RFC 5644 [RFC5644] is limited to active measurements using a single
source packet or stream. Its scope is also limited to observations
of corresponding packets along the path (spatial metric) and at one
or more destinations (one-to-group) along the path.
Instead, the scope of this memo is to define multiparty metrics for
passive and hybrid measurements in a group-to-group topology with
multiple sources and destinations.
RFC 5644 [RFC5644] introduces metric names that can be reused here
but have to be extended and rephrased to be applied to the Alternate-
Marking schema:
Fioccola, et al. Expires December 9, 2022 [Page 6]
Internet-Draft ClustAltMark June 2022
a. the multiparty metrics are not only one-to-group metrics but can
be also group-to-group metrics;
b. the spatial metrics, used for measuring the performance of
segments of a source to destination path, are applied here to
group-to-group segments (called clusters).
3. Flow Classification
A unicast flow is identified by all the packets having a set of
common characteristics. This definition is inspired by RFC 7011
[RFC7011].
As an example, by considering a flow as all the packets sharing the
same source IP address or the same destination IP address, it is easy
to understand that the resulting pattern will not be a point-to-point
connection, but a point-to-multipoint or multipoint-to-point
connection.
In general, a flow can be defined by a set of selection rules used to
match a subset of the packets processed by the network device. These
rules specify a set of Layer 3 and Layer 4 header fields
(identification fields) and the relative values that must be found in
matching packets.
The choice of the identification fields directly affects the type of
paths that the flow would follow in the network. In fact, it is
possible to relate a set of identification fields with the pattern of
the resulting graphs, as listed in Figure 1.
A TCP 5-tuple usually identifies flows following either a single path
or a point-to-point multipath (in the case of load balancing). On
the contrary, a single source address selects aggregate flows
following a point-to-multipoint, while a multipoint-to-point can be
the result of a matching on a single destination address. In the
case where a selection rule and its reverse are used for
bidirectional measurements, they can correspond to a point-to-
multipoint in one direction and a multipoint-to-point in the opposite
direction.
So the flows to be monitored are selected into the monitoring points
using packet selection rules, which can also change the pattern of
the monitored network.
Note that, more generally, the flow can be defined at different
levels based on the potential encapsulation, and additional
conditions that are not in the packet header can also be included as
part of matching criteria.
Fioccola, et al. Expires December 9, 2022 [Page 7]
Internet-Draft ClustAltMark June 2022
The Alternate-Marking method is applicable only to a single path (and
partially to a one-to-one multipath), so the extension proposed in
this document is suitable also for the most general case of
multipoint-to-multipoint, which embraces all the other patterns of
Figure 1.
point-to-point single path
+------+ +------+ +------+
---<> R1 <>----<> R2 <>----<> R3 <>---
+------+ +------+ +------+
point-to-point multipath
+------+
<> R2 <>
/ +------+ \
/ \
+------+ / \ +------+
---<> R1 <> <> R4 <>---
+------+ \ / +------+
\ /
\ +------+ /
<> R3 <>
+------+
point-to-multipoint
+------+
<> R4 <>---
/ +------+
+------+ /
<> R2 <>
/ +------+ \
+------+ / \ +------+
---<> R1 <> <> R5 <>---
+------+ \ +------+
\ +------+
<> R3 <>
+------+ \
\ +------+
<> R6 <>---
+------+
multipoint-to-point
+------+
---<> R1 <>
Fioccola, et al. Expires December 9, 2022 [Page 8]
Internet-Draft ClustAltMark June 2022
+------+ \
\ +------+
<> R4 <>
/ +------+ \
+------+ / \ +------+
---<> R2 <> <> R6 <>---
+------+ / +------+
+------+ /
<> R5 <>
/ +------+
+------+ /
---<> R3 <>
+------+
multipoint-to-multipoint
+------+ +------+
---<> R1 <> <> R6 <>---
+------+ \ / +------+
\ +------+ /
<> R4 <>
+------+ \
+------+ \ +------+
---<> R2 <> <> R7 <>---
+------+ \ / +------+
\ +------+ /
<> R5 <>
/ +------+ \
+------+ / \ +------+
---<> R3 <> <> R8 <>---
+------+ +------+
Figure 1: Flow Classification
The case of unicast flow is considered in Figure 1. The anycast flow
is also in scope, because there is no replication and only a single
node from the anycast group receives the traffic, so it can be viewed
as a special case of unicast flow. Furthermore, an ECMP flow is in
scope by definition, since it is a point-to-multipoint unicast flow.
4. Extension of the Method to Multipoint Flows
By using the Alternate-Marking method, only point-to-point paths can
be monitored. To have an IP (TCP/UDP) flow that follows a point-to-
point path, in general we have to define, with a specific value, 5
identification fields (IP Source, IP Destination, Transport Protocol,
Source Port, Destination Port).
Fioccola, et al. Expires December 9, 2022 [Page 9]
Internet-Draft ClustAltMark June 2022
Multipoint Alternate Marking enables the performance measurement for
multipoint flows selected by identification fields without any
constraints (even the entire network production traffic). It is also
possible to use multiple marking points for the same monitored flow.
4.1. Monitoring Network
The monitoring network is deduced from the production network by
identifying the nodes of the graph that are the measurement points,
and the links that are the connections between measurement points.
There are some techniques that can help with the building of the
monitoring network (as an example, see [I-D.ietf-ippm-route]). In
general, there are different options: the monitoring network can be
obtained by considering all the possible paths for the traffic or
periodically checking the traffic (e.g. daily, weekly, monthly) and
updating the graph as appropriate, but this is up to the Network
Management System (NMS) configuration.
So a graph model of the monitoring network can be built according to
the Alternate-Marking method: the monitored interfaces and links are
identified. Only the measurement points and links where the traffic
has flowed have to be represented in the graph.
Figure 2 shows a simple example of a monitoring network graph:
Fioccola, et al. Expires December 9, 2022 [Page 10]
Internet-Draft ClustAltMark June 2022
+------+
<> R6 <>---
/ +------+
+------+ +------+ /
<> R2 <>---<> R4 <>
/ +------+ \ +------+ \
/ \ \ +------+
+------+ / +------+ \ +------+ <> R7 <>---
---<> R1 <>---<> R3 <>---<> R5 <> +------+
+------+ \ +------+ \ +------+ \
\ \ \ +------+
\ \ <> R8 <>---
\ \ +------+
\ \
\ \ +------+
\ <> R9 <>---
\ +------+
\
\ +------+
<> R10 <>---
+------+
Figure 2: Monitoring Network Graph
Each monitoring point is characterized by the packet counter that
refers only to a marking period of the monitored flow. Also, it is
assumed that there be a monitoring point at all possible egress
points of the multipoint monitored network.
The same is also applicable for the delay, but it will be described
in the following sections.
The rest of the document assumes that the traffic is going from left
to right in order to simplify the explanation. But the analysis done
for one direction applies equally to all directions.
4.2. Network Packet Loss
Since all the packets of the considered flow leaving the network have
previously entered the network, the number of packets counted by all
the input nodes is always greater than, or equal to, the number of
packets counted by all the output nodes. Non-initial fragments are
not considered here.
In the case of no packet loss occurring in the marking period, if all
the input and output points of the network domain to be monitored are
measurement points, the sum of the number of packets on all the
Fioccola, et al. Expires December 9, 2022 [Page 11]
Internet-Draft ClustAltMark June 2022
ingress interfaces equals the number on egress interfaces for the
monitored flow. In this circumstance, if no packet loss occurs, the
intermediate measurement points only have the task of splitting the
measurement.
It is possible to define the Network Packet Loss of one monitored
flow for a single period. In a packet network, the number of lost
packets is the number of packets counted by the input nodes minus the
number of packets counted by the output nodes. This is true for
every packet flow in each marking period.
The monitored network packet loss with n input nodes and m output
nodes is given by:
PL = (PI1 + PI2 +...+ PIn) - (PO1 + PO2 +...+ POm)
where:
PL is the network packet loss (number of lost packets)
PIi is the number of packets flowed through the i-th input node in
this period
POj is the number of packets flowed through the j-th output node in
this period
The equation is applied on a per-time-interval basis and a per-flow
basis:
The reference interval is the Alternate-Marking period, as defined
in [I-D.ietf-ippm-rfc8321bis].
The flow definition is generalized here. Indeed, as described
before, a multipoint packet flow is considered, and the
identification fields can be selected without any constraints.
5. Network Clustering
The previous equation of Section 4.2 can determine the number of
packets lost globally in the monitored network, exploiting only the
data provided by the counters in the input and output nodes.
In addition, it is also possible to leverage the data provided by the
other counters in the network to converge on the smallest
identifiable subnetworks where the losses occur. These subnetworks
are named "clusters".
Fioccola, et al. Expires December 9, 2022 [Page 12]
Internet-Draft ClustAltMark June 2022
A cluster graph is a subnetwork of the entire monitoring network
graph that still satisfies the packet loss equation (introduced in
the previous section), where PL in this case is the number of packets
lost in the cluster. As for the entire monitoring network graph, the
cluster is defined on a per-flow basis.
For this reason, a cluster should contain all the arcs emanating from
its input nodes and all the arcs terminating at its output nodes.
This ensures that we can count all the packets (and only those)
exiting an input node again at the output node, whatever path they
follow.
In a completely monitored unidirectional network (a network where
every network interface is monitored), each network device
corresponds to a cluster, and each physical link corresponds to two
clusters (one for each device).
Clusters can have different sizes depending on the flow-filtering
criteria adopted.
Moreover, sometimes clusters can be optionally simplified. For
example, when two monitored interfaces are divided by a single router
(one is the input interface, the other is the output interface, and
the router has only these two interfaces), instead of counting
exactly twice, upon entering and leaving, it is possible to consider
a single measurement point. In this case, we do not care about the
internal packet loss of the router.
It is worth highlighting that it might also be convenient to define
clusters based on the topological information so that they are
applicable to all the possible flows in the monitored network.
5.1. Algorithm for Clusters Partition
A simple algorithm can be applied in order to split our monitoring
network into clusters. This can be done for each direction
separately, indeed a node cannot be both a source and a destination.
The clusters partition is based on the monitoring network graph,
which can be valid for a specific flow or can also be general and
valid for the entire network topology.
It is a two-step algorithm:
o Group the links where there is the same starting node;
o Join the grouped links with at least one ending node in common.
Fioccola, et al. Expires December 9, 2022 [Page 13]
Internet-Draft ClustAltMark June 2022
Considering that the links are unidirectional, the first step implies
listing all the links as connections between two nodes and grouping
the different links if they have the same starting node. Note that
it is possible to start from any link, and the procedure will work.
Following this classification, the second step implies eventually
joining the groups classified in the first step by looking at the
ending nodes. If different groups have at least one common ending
node, they are put together and belong to the same set. After the
application of the two steps of the algorithm, each one of the
composed sets of links, together with the endpoint nodes, constitutes
a cluster.
In our monitoring network graph example, it is possible to identify
the clusters partition by applying this two-step algorithm.
The first step identifies the following groups:
1. Group 1: (R1-R2), (R1-R3), (R1-R10)
2. Group 2: (R2-R4), (R2-R5)
3. Group 3: (R3-R5), (R3-R9)
4. Group 4: (R4-R6), (R4-R7)
5. Group 5: (R5-R8)
And then, the second step builds the clusters partition (in
particular, we can underline that Groups 2 and 3 connect together,
since R5 is in common):
1. Cluster 1: (R1-R2), (R1-R3), (R1-R10)
2. Cluster 2: (R2-R4), (R2-R5), (R3-R5), (R3-R9)
3. Cluster 3: (R4-R6), (R4-R7)
4. Cluster 4: (R5-R8)
The flow direction here considered is from left to right. For the
opposite direction, the same reasoning can be applied, and in this
example, you get the same clusters partition.
In the end, the following 4 clusters are obtained:
Cluster 1
+------+
Fioccola, et al. Expires December 9, 2022 [Page 14]
Internet-Draft ClustAltMark June 2022
<> R2 <>---
/ +------+
/
+------+ / +------+
---<> R1 <>---<> R3 <>---
+------+ \ +------+
\
\
\
\
\
\
\
\
\ +------+
<> R10 <>---
+------+
Cluster 2
+------+ +------+
---<> R2 <>---<> R4 <>---
+------+ \ +------+
\
+------+ \ +------+
---<> R3 <>---<> R5 <>---
+------+ \ +------+
\
\
\
\
\ +------+
<> R9 <>---
+------+
Cluster 3
+------+
<> R6 <>---
/ +------+
+------+ /
---<> R4 <>
+------+ \
\ +------+
<> R7 <>---
+------+
Fioccola, et al. Expires December 9, 2022 [Page 15]
Internet-Draft ClustAltMark June 2022
Cluster 4
+------+
---<> R5 <>
+------+ \
\ +------+
<> R8 <>---
+------+
Figure 3: Clusters Example
There are clusters with more than two nodes as well as two-node
clusters. In the two-node clusters, the loss is on the link (Cluster
4). In more-than-two-node clusters, the loss is on the cluster, but
we cannot know in which link (Cluster 1, 2, or 3).
The algorithm, as applied in this example of a point-to-multipoint
network, works for the more general case of multipoint-to-multipoint
network in the same way. It should be highlighted that for a
multipoint-to-multipoint network the multiple sources MUST mark
coherently the traffic and MUST be synchronized with all the other
nodes according to the timing requirements detailed in Section 8.
When the clusters partition is done, the calculation of packet loss,
delay and delay variation can be made on a cluster basis. Note that
the packet counters for each marking period permit calculating the
packet rate on a cluster basis, so Committed Information Rate (CIR)
and Excess Information Rate (EIR) could also be deduced on a cluster
basis.
Obviously, by combining some clusters in a new connected subnetwork
the packet-loss rule is still true. So it is also possible to
consider combinations of clusters if and where it suits.
In this way, in a very large network, there is no need to configure
detailed filter criteria to inspect the traffic. It is possible to
check a multipoint network and, in case of problems, go deep with a
step-by-step cluster analysis, but only for the cluster or
combination of clusters where the problem happens.
In summary, once a flow is defined, the algorithm to build the
clusters partition is based on topological information; therefore, it
considers all the possible links and nodes crossed by the given flow,
even if there is no traffic. So, if the flow does not enter or
traverse all the nodes, the counters have a non-zero value for the
involved nodes and a zero value for the other nodes without traffic;
but in the end, all the formulas are still valid.
Fioccola, et al. Expires December 9, 2022 [Page 16]
Internet-Draft ClustAltMark June 2022
The algorithm described above network is an iterative clustering
algorithm, but it is also possible to apply a recursive clustering
algorithm by using the node-node adjacency matrix representation
[IEEE-ACM-ToN-MPNPM].
The complete and mathematical analysis of the possible algorithms for
clusters partition, including the considerations in terms of
efficiency and a comparison between the different methods, is in the
paper [IEEE-ACM-ToN-MPNPM].
6. Multipoint Packet Loss Measurement
The Network Packet Loss, defined in Section 4.2, valid for the an
entire monitored flow, can easily be extended to each multipoint path
(e.g., the whole multipoint network, a cluster, or a combination of
clusters). In this way it is possible to calculate Multipoint Packet
Loss that is representative of a multipoint path.
The same equation of Section 4.2 can be applied to a generic
multipoint path like a cluster or a combination of clusters, where
the number of packets are those entering and leaving the multipoint
path.
By applying the algorithm described in Section 5.1, it is possible to
split the monitoring network into clusters. Then, packet loss can be
measured on a cluster basis for each single period by considering the
counters of the input and output nodes that belong to the specific
cluster. This can be done for every packet flow in each marking
period.
7. Multipoint Delay and Delay Variation
The same line of reasoning can be applied to delay and delay
variation. The delay measurement methods defined in
[I-D.ietf-ippm-rfc8321bis] can be extended to the case of multipoint
flows. It is important to highlight that both delay and delay-
variation measurements make sense in a multipoint path. The delay
variation is calculated by considering the same packets selected for
measuring the delay.
In general, it is possible to perform delay and delay-variation
measurements on the basis of multipoint paths or single packets:
o Delay measurements on the basis of multipoint paths mean that the
delay value is representative of an entire multipoint path (e.g.,
the whole multipoint network, a cluster, or a combination of
clusters).
Fioccola, et al. Expires December 9, 2022 [Page 17]
Internet-Draft ClustAltMark June 2022
o Delay measurements on a single-packet basis mean that it is
possible to use a multipoint path just to easily couple packets
between input and output nodes of a multipoint path, as described
in the following sections.
7.1. Delay Measurements on a Multipoint-Paths Basis
7.1.1. Single-Marking Measurement
Mean delay and mean delay-variation measurements can also be
generalized to the case of multipoint flows. It is possible to
compute the average one-way delay of packets in one block, a cluster,
or the entire monitored network.
The average latency can be measured as the difference between the
weighted averages of the mean timestamps of the sets of output and
input nodes. This means that, in the calculation, it is possible to
weigh the timestamps by considering the number of packets for each
endpoints.
Note that, since the one-way delay value is representative of a
multipoint path, it is possible to calculate the two-way delay of a
multipoint path by summing the one-way delays of the two directions,
similarly to [I-D.ietf-ippm-rfc8321bis].
7.2. Delay Measurements on a Single-Packet Basis
7.2.1. Single- and Double-Marking Measurement
Delay and delay-variation measurements associated with only one
picked packet per period, both single and double marked, cannot be
easily performed in a multipoint scenario since there are some
limitations:
Single marking based on the first/last packet of the interval does
not work properly. Indeed, by considering a point-to-multipoint
scenario, it is not possible to recognize which path the first
packet of each block takes over the multipoint flow in order to
correlate it. This is also true for the general case of the
multipoint-to-multipoint scenario.
Double marking or multiplexed marking work but only through
statistical means. In a point-to-multipoint scenario, by
selecting only a single packet with the second marking for each
block, it is possible to follow and calculate the delay for that
picked packet. But the measurement can only be done for a single
path in each marking period. To traverse all the paths of the
multipoint flow, it can theoretically be done by continuing the
Fioccola, et al. Expires December 9, 2022 [Page 18]
Internet-Draft ClustAltMark June 2022
measurement for the following marking periods and expect to span
all the paths. In the general case of a multipoint-to-multipoint
path, it is also needed to take into account the multiple source
nodes which complicate the correlation of the samples. In this
case, it can be possible to select the second marked packet only
for a source node at a time for each block and cover the remaining
source nodes one by one in the next marking periods.
Note that, since the one-way delay measurement is done on a single-
packet basis, it is always possible to calculate the two-way delay
but it is not immediate since it is necessary to couple the
measurement on each single path with the opposite direction. In this
case the NMS can do the calculation.
If we would perform a delay measurement for more than one picked
packet and for all the paths of the multipoint flow in the same
marking period, neither the single- nor the double-marking method are
applicable in the multipoint scenario. The packets follow different
paths and it becomes very difficult to correlate marked packets in a
multipoint-to-multipoint path if there are more than one per period.
A desirable option is to monitor simultaneously all the paths of a
multipoint path in the same marking period. For this purpose,
hashing can be used, as reported in the next section.
7.2.2. Hashing Selection Method
RFCs 5474 [RFC5474] and 5475 [RFC5475] introduce sampling and
filtering techniques for IP packet selection.
The hash-based selection methodologies for delay measurement can work
in a multipoint-to-multipoint path and MAY be used either coupled to
mean delay or stand-alone.
[I-D.mizrahi-ippm-marking] introduces how to use the hash method (RFC
5474 [RFC5474] and RFC 5475 [RFC5475]) combined with the Alternate-
Marking method for point-to-point flows. It is also called Mixed
Hashed Marking because it refers to the conjunction of the marking
method and the hashing technique. It involves only the single
marking, indeed it is supposed that double marking is not used with
hashing. The coupling of the single marking with the hashing
selection allows to choose a simplified hash function since the
alternation of blocks gives temporal boundaries for the hashing
samples. The marking batches anchor the samples selected with
hashing and this eases the correlation of the hashing packets along
the path. For example, in case an hashed sample is lost, it is
confined to the considered block without affecting the identification
of the samples for the following blocks.
Fioccola, et al. Expires December 9, 2022 [Page 19]
Internet-Draft ClustAltMark June 2022
Using the hash-based sampling, the number of samples in each block
may vary a lot because it depends on the packet rate that is
variable. A dynamic approach can help to have an almost fixed number
of samples for each marking period, and this is a better option for
making regular measurements over time. In the hash-based sampling,
Alternate Marking is used to create periods, so that hash-based
samples are divided into batches, which allows anchoring the selected
samples to their period. Moreover, in a dynamic hash-based sampling,
it can be possible to dynamically adapt the length of the hash value
to meet the current packet rate, so that the number of samples is
bounded in each marking period.
In a multipoint environment, the hashing selection MAY be the
solution for performing delay measurements on specific packets and
overcoming the single- and double-marking limitations.
8. Synchronization and Timing
It is important to consider the timing aspects, since out-of-order
packets happen and have to be handled as well, as described in
[I-D.ietf-ippm-rfc8321bis].
However, in a multisource situation, an additional issue has to be
considered. With multipoint path, the egress nodes will receive
alternate marked packets in random order from different ingress
nodes, and this must not affect the measurement.
So, if we analyze a multipoint-to-multipoint path with more than one
marking node, it is important to recognize the reference measurement
interval. In general, the measurement interval for describing the
results is the interval of the marking node that is more aligned with
the start of the measurement, as reported in Figure 4.
Note that the mark switching approach based on a fixed timer is
considered in this document.
time -> start stop
T(R1) |-------------|
T(R2) |-------------|
T(R3) |------------|
Figure 4: Measurement Interval
In Figure 4, it is assumed that the node with the earliest clock (R1)
identifies the right starting and ending times of the measurement,
but it is just an assumption, and other possibilities could occur.
Fioccola, et al. Expires December 9, 2022 [Page 20]
Internet-Draft ClustAltMark June 2022
So, in this case, T(R1) is the measurement interval, and its
recognition is essential in order to make comparisons with other
active/passive/hybrid Packet Loss metrics.
Regarding the timing constraints of the methodology,
[I-D.ietf-ippm-rfc8321bis] already describes two contributions that
are taken into account: the clock error between network devices and
the network delay between the measurement points.
When we expand to a multipoint environment, we have to consider that
there are more marking nodes that mark the traffic based on
synchronized clock time. But, due to different synchronization
issues that may happen, the marking batches can be of different
lengths and with different offsets when they get mixed in a
multipoint flow. The additional gap that results between the sources
can be incorporated into A, which is the maximum clock skew between
the network devices, as already defined in
[I-D.ietf-ippm-rfc8321bis].
...BBBBBBBBB | AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA | BBBBBBBBB...
|<======================================>|
| L |
...=========>|<==================><==================>|<==========...
| L/2 L/2 |
|<====>| |<====>|
d | | d
|<========================>|
available counting interval
Figure 5: Timing Aspects
Moreover, it is assumed that the multipoint path can be modeled with
a normal distribution, otherwise it is necessary to reformulate based
on the type of distribution. Under this assumption, the definition
of the guard band d is still applicable as defined in
[I-D.ietf-ippm-rfc8321bis] and is given by:
d = A + D_avg + 3*D_stddev,
where A is the clock accuracy, D_avg is the average value of the
network delay, and D_stddev is the standard deviation of the delay.
As shown in Figure 5 and according to [I-D.ietf-ippm-rfc8321bis], the
condition that must be satisfied to enable the method to function
properly is that the available counting interval must be > 0, and
that means:
Fioccola, et al. Expires December 9, 2022 [Page 21]
Internet-Draft ClustAltMark June 2022
L - 2d > 0.
This formula needs to be verified for each measurement point on the
multipoint path.
Note that the timing considerations are valid for both packet loss
and delay measurements.
9. Results of the Multipoint Alternate Marking Experiment
The methodology described in the previous sections can be applied to
various performance measurement problems, as also explained in
[I-D.ietf-ippm-rfc8321bis].
Either one or two flag bits might be available for marking in
different deployments:
One flag: packet loss measurement SHOULD be done as described in
Section 6 by applying the network clustering partition described
in Section 5. While delay measurement MAY be done according to
the Mean delay calculation representative of the multipoint path,
as described in Section 7.1.1. Single-marking method based on the
first/last packet of the interval cannot be applied, as mentioned
in Section 7.2.1.
Two flags: packet loss measurement SHOULD be done as described in
Section 6 by applying the network clustering partition described
in Section 5. While delay measurement SHOULD be done on a single
packet basis according to double-marking method Section 7.2.1. In
this case the Mean delay calculation (Section 7.1.1) MAY also be
used as a representative value of a multipoint path.
One flag and hash-based selection: packet loss measurement SHOULD
be done as described in Section 6 by applying the network
clustering partition described in Section 5. Hash-based selection
methodologies, introduced in Section 7.2.2, MAY be used for delay
measurement.
The experiment with Multipoint Alternate Marking methodologies
confirmed the benefits of the Alternate Marking methodology described
in [I-D.ietf-ippm-rfc8321bis], as its extension to the general case
of multipoint-to-multipoint scenarios.
The Multipoint Alternate Marking Method is RECOMMENDED only for
controlled domains, as per [I-D.ietf-ippm-rfc8321bis].
Fioccola, et al. Expires December 9, 2022 [Page 22]
Internet-Draft ClustAltMark June 2022
10. A Closed-Loop Performance-Management Approach
The Multipoint Alternate-Marking framework that is introduced in this
document adds flexibility to Performance Management (PM), because it
can reduce the order of magnitude of the packet counters. This
allows an SDN orchestrator to supervise, control, and manage PM in
large networks.
The monitoring network can be considered as a whole or split into
clusters that are the smallest subnetworks (group-to-group segments),
maintaining the packet-loss property for each subnetwork. The
clusters can also be combined in new, connected subnetworks at
different levels, depending on the detail we want to achieve.
An SDN controller or a Network Management System (NMS) can calibrate
performance measurements, since they are aware of the network
topology. They can start without examining in depth. In case of
necessity (packet loss is measured or the delay is too high), the
filtering criteria could be immediately reconfigured in order to
perform a partition of the network by using clusters and/or different
combinations of clusters. In this way, the problem can be localized
in a specific cluster or a single combination of clusters, and a more
detailed analysis can be performed step by step by successive
approximation up to a point-to-point flow detailed analysis. This is
the so-called "closed loop".
This approach can be called "network zooming" and can be performed in
two different ways:
1) change the traffic filter and select more detailed flows;
2) activate new measurement points by defining more specified
clusters.
The network-zooming approach implies that some filters or rules are
changed and that therefore there is a transient time to wait once the
new network configuration takes effect. This time can be determined
by the Network Orchestrator/Controller, based on the network
conditions.
For example, if the network zooming identifies the performance
problem for the traffic coming from a specific source, we need to
recognize the marked signal from this specific source node and its
relative path. For this purpose, we can activate all the available
measurement points and better specify the flow filter criteria (i.e.,
5-tuple). As an alternative, it can be enough to select packets from
the specific source for delay measurements; in this case, it is
Fioccola, et al. Expires December 9, 2022 [Page 23]
Internet-Draft ClustAltMark June 2022
possible to apply the hashing technique, as mentioned in the previous
sections.
[I-D.song-opsawg-ifit-framework] defines an architecture where the
centralized Data Collector and Network Management can apply the
intelligent and flexible Alternate-Marking algorithm as previously
described.
As for [I-D.ietf-ippm-rfc8321bis], it is possible to classify the
traffic and mark a portion of the total traffic. For each period,
the packet rate and bandwidth are calculated from the number of
packets. In this way, the network orchestrator becomes aware if the
traffic rate surpasses limits. In addition, more precision can be
obtained by reducing the marking period; indeed, some implementations
use a marking period of 1 sec or less.
In addition, an SDN controller could also collect the measurement
history.
It is important to mention that the Multipoint Alternate Marking
framework also helps Traffic Visualization. Indeed, this methodology
is very useful for identifying which path or cluster is crossed by
the flow.
11. Security Considerations
This document specifies a method of performing measurements that does
not directly affect Internet security or applications that run on the
Internet. However, implementation of this method must be mindful of
security and privacy concerns, as explained in
[I-D.ietf-ippm-rfc8321bis].
12. IANA Considerations
This document has no IANA actions.
13. Contributors
Greg Mirsky
Ericsson
Email: gregimirsky@gmail.com
Tal Mizrahi
Huawei Technologies
Email: tal.mizrahi.phd@gmail.com
Xiao Min
ZTE Corp.
Fioccola, et al. Expires December 9, 2022 [Page 24]
Internet-Draft ClustAltMark June 2022
Email: xiao.min2@zte.com.cn
14. Acknowledgements
The authors would like to thank Martin Duke and Tommy Pauly for their
assistance and their detailed and precious reviews.
15. References
15.1. Normative References
[I-D.ietf-ippm-rfc8321bis]
Fioccola, G., Cociglio, M., Mirsky, G., Mizrahi, T., and
T. Zhou, "Alternate-Marking Method", draft-ietf-ippm-
rfc8321bis-01 (work in progress), April 2022.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC5475] Zseby, T., Molina, M., Duffield, N., Niccolini, S., and F.
Raspall, "Sampling and Filtering Techniques for IP Packet
Selection", RFC 5475, DOI 10.17487/RFC5475, March 2009,
<https://www.rfc-editor.org/info/rfc5475>.
[RFC5644] Stephan, E., Liang, L., and A. Morton, "IP Performance
Metrics (IPPM): Spatial and Multicast", RFC 5644,
DOI 10.17487/RFC5644, October 2009,
<https://www.rfc-editor.org/info/rfc5644>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
15.2. Informative References
[I-D.ietf-ippm-route]
Alvarez-Hamelin, J. I., Morton, A., Fabini, J., Pignataro,
C., and R. Geib, "Advanced Unidirectional Route Assessment
(AURA)", draft-ietf-ippm-route-10 (work in progress),
August 2020.
[I-D.mizrahi-ippm-marking]
Mizrahi, T., Fioccola, G., Cociglio, M., Chen, M., and G.
Mirsky, "Marking Methods for Performance Measurement",
draft-mizrahi-ippm-marking-00 (work in progress), October
2021.
Fioccola, et al. Expires December 9, 2022 [Page 25]
Internet-Draft ClustAltMark June 2022
[I-D.song-opsawg-ifit-framework]
Song, H., Qin, F., Chen, H., Jin, J., and J. Shin, "A
Framework for In-situ Flow Information Telemetry", draft-
song-opsawg-ifit-framework-17 (work in progress), February
2022.
[I-D.zhou-ippm-enhanced-alternate-marking]
Zhou, T., Fioccola, G., Liu, Y., Cociglio, M., Lee, S.,
and W. Li, "Enhanced Alternate Marking Method", draft-
zhou-ippm-enhanced-alternate-marking-09 (work in
progress), February 2022.
[IEEE-ACM-ToN-MPNPM]
IEEE/ACM TRANSACTION ON NETWORKING, "Multipoint Passive
Monitoring in Packet Networks",
DOI 10.1109/TNET.2019.2950157, 2019.
[IEEE-Network-PNPM]
IEEE Network, "AM-PM: Efficient Network Telemetry using
Alternate Marking", DOI 10.1109/MNET.2019.1800152, 2019.
[RFC5474] Duffield, N., Ed., Chiou, D., Claise, B., Greenberg, A.,
Grossglauser, M., and J. Rexford, "A Framework for Packet
Selection and Reporting", RFC 5474, DOI 10.17487/RFC5474,
March 2009, <https://www.rfc-editor.org/info/rfc5474>.
[RFC7011] Claise, B., Ed., Trammell, B., Ed., and P. Aitken,
"Specification of the IP Flow Information Export (IPFIX)
Protocol for the Exchange of Flow Information", STD 77,
RFC 7011, DOI 10.17487/RFC7011, September 2013,
<https://www.rfc-editor.org/info/rfc7011>.
[RFC8889] Fioccola, G., Ed., Cociglio, M., Sapio, A., and R. Sisto,
"Multipoint Alternate-Marking Method for Passive and
Hybrid Performance Monitoring", RFC 8889,
DOI 10.17487/RFC8889, August 2020,
<https://www.rfc-editor.org/info/rfc8889>.
Appendix A. Changes Log
Changes from RFC 8889 in draft-fioccola-rfc8889bis-00 include:
o Minor editorial changes
o Removed section on "Examples of application"
Changes in draft-fioccola-rfc8889bis-01 include:
Fioccola, et al. Expires December 9, 2022 [Page 26]
Internet-Draft ClustAltMark June 2022
o Considerations on BUM traffic
o Reference to RFC8321bis for the fragmentation part
o Revised section on "Delay Measurements on a Single-Packet Basis"
o Revised section on "Timing Aspects"
Changes in draft-fioccola-rfc8889bis-02 include:
o Clarified the formula in the section on "Timing Aspects" to be
aligned with RFC 8321
o Considerations on two-way delay measurements in both sections 8.1
and 8.2 on delay measurements
o Clarified in section 4.1 on "Monitoring Network" that the
description is done for one direction but it can easily be
extended to all direction
o New section on "Results of the Multipoint Alternate Marking
Experiment"
Changes in draft-fioccola-rfc8889bis-03 include:
o Moved and renamed section on "Timing Aspects" as "Synchronization
and Timing"
o Renamed old section on "Multipoint Packet Loss" as "Network Packet
Loss"
o New section on "Multipoint Packet Loss Measurement"
o Renamed section on "Multipoint Performance Measurement" as
"Extension of the Method to Multipoint Flows"
Changes in draft-fioccola-rfc8889bis-04/draft-ietf-ippm-rfc8889bis-00
include:
o Revised section 5.1 on "Algorithm for Clusters Partition"
Changes in draft-ietf-ippm-rfc8889bis-01 include:
o New section on "Summary of Changes from RFC 8889"
Changes in draft-ietf-ippm-rfc8889bis-02 include:
Fioccola, et al. Expires December 9, 2022 [Page 27]
Internet-Draft ClustAltMark June 2022
o Revised sections on "Single- and Double-Marking Measurement",
"Hashing Selection Method" and "Synchronization and Timing"
o Revised references
Authors' Addresses
Giuseppe Fioccola (editor)
Huawei Technologies
Riesstrasse, 25
Munich 80992
Germany
Email: giuseppe.fioccola@huawei.com
Mauro Cociglio
Telecom Italia
Via Reiss Romoli, 274
Torino 10148
Italy
Email: mauro.cociglio@telecomitalia.it
Amedeo Sapio
Intel Corporation
4750 Patrick Henry Dr.
Santa Clara, CA 95054
USA
Email: amedeo.sapio@intel.com
Riccardo Sisto
Politecnico di Torino
Corso Duca degli Abruzzi, 24
Torino 10129
Italy
Email: riccardo.sisto@polito.it
Fioccola, et al. Expires December 9, 2022 [Page 28]
Internet-Draft ClustAltMark June 2022
Tianran Zhou
Huawei Technologies
156 Beiqing Rd.
Beijing 100095
China
Email: zhoutianran@huawei.com
Fioccola, et al. Expires December 9, 2022 [Page 29]
