IPsecME Working Group S. Hanna
Internet-Draft Juniper
Intended status: Informational V. Manral
Expires: June 10, 2013 HP
December 7, 2012
Auto Discovery VPN Problem Statement and Requirements
draft-ietf-ipsecme-ad-vpn-problem-02
Abstract
This document describes the problem of enabling a large number of
systems to communicate directly using IPsec to protect the traffic
between them. It then expands on the requirements, for such a
solution.
Manual configuration of all possible tunnels is too cumbersome in
many such cases. In other cases the IP address of endpoints change
or the endpoints may be behind NAT gateways, making static
configuration impossible. The Auto Discovery VPN solution is
chartered to address these requirements.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 10, 2013.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Hanna & Manral Expires June 10, 2013 [Page 1]
Internet-Draft Auto Discovery VPN December 2012
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
1.2. Conventions Used in This Document . . . . . . . . . . . . 4
2. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1. Endpoint-to-Endpoint AD VPN Use Case . . . . . . . . . . . 5
2.2. Gateway-to-Gateway AD VPN Use Case . . . . . . . . . . . . 5
2.3. Endpoint-to-Gateway AD VPN Use Case . . . . . . . . . . . 6
3. Inadequacy of Existing Solutions . . . . . . . . . . . . . . . 7
3.1. Exhaustive Configuration . . . . . . . . . . . . . . . . . 7
3.2. Star Topology . . . . . . . . . . . . . . . . . . . . . . 7
3.3. Proprietary Approaches . . . . . . . . . . . . . . . . . . 8
4. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1. Gateway and Endpoint Requirements . . . . . . . . . . . . 9
5. Security Considerations . . . . . . . . . . . . . . . . . . . 12
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 14
8. Normative References . . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16
Hanna & Manral Expires June 10, 2013 [Page 2]
Internet-Draft Auto Discovery VPN December 2012
1. Introduction
IPsec [RFC4301] is used in several different cases, including tunnel-
mode site-to-site VPNs and Remote Access VPNs. Host to host
communication employing transport mode also exists, but is far less
commonly deployed.
The subject of this document is the problem presented by large scale
deployments of IPsec and the requirements on a solution to address
the problem. These may be a large collection of VPN gateways
connecting various sites, a large number of remote endpoints
connecting to a number of gateways or to each other, or a mix of the
two. The gateways and endpoints may belong to a single
administrative domain or several domains with a trust relationship.
Section 4.4 of RFC 4301 describes the major IPsec databases needed
for IPsec processing. It requires an extensive configuration for
each tunnel, so manually configuring a system of many gateways and
endpoints becomes infeasible and inflexible.
The difficulty is that all the configuration mentioned in RFC 4301 is
not superfluous. IKE implementations need to know the identity and
credentials of all possible peer systems, as well as the addresses of
hosts and/or networks behind them. A simplified mechanism for
dynamically establishing point-to-point tunnels is needed. Section 2
contains several use cases that motivate this effort.
1.1. Terminology
Endpoint - A device that implements IPsec for its own traffic but
does not act as a gateway.
Gateway - A network device that implements IPsec to protect traffic
flowing through the device.
Point-to-Point - Direct communication between two parties without
active participation (e.g. encryption or decryption) by any other
parties.
Hub - The central point in a star topology/ dynamic full mesh
topology, or one of the central points in the full mesh style VPN,
i.e. gateway where multiple other hubs or spokes connect to. The
hubs usually forward traffic coming from encrypted links to other
encrypted links, i.e. there is no devices connected to it in clear.
Spoke - The edge devices in the a star topology/ dynamic full mesh
topology, or gateway which forwards traffic from multiple cleartext
devices to other hubs or spokes, and some of those other devices are
Hanna & Manral Expires June 10, 2013 [Page 3]
Internet-Draft Auto Discovery VPN December 2012
connected to it in clear (i.e. it encrypt data coming from cleartext
device and forwards it to the AD VPN).
Star topology - This is the topology where there is direct
connectivity only between the hub and spoke and communication between
the 2 spokes happens through the hub.
Full Mesh topology - This is the topology where there is a direct
connectivity between every Spoke to every other Spoke directly,
without the traffic between the spokes having to be redirected
through an intermediate hub device.
Dynamic Full Mesh topology - This is the topology where direct
connections exist in a hub and spoke manner, but dynamic connections
are created/ removed between the spokes on a need basis.
Security Association (SA) - Defined in [RFC4301].
1.2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Hanna & Manral Expires June 10, 2013 [Page 4]
Internet-Draft Auto Discovery VPN December 2012
2. Use Cases
This section presents the key use cases for large-scale point-to-
point VPN.
In all of these use cases, the participants (endpoints and gateways)
may be from a single organization or from multiple organizations with
an established trust relationship. When multiple organizations are
involved, products from multiple vendors are employed so open
standards are needed to provide interoperability. Establishing
communications between participants with no established trust
relationship is out of scope for this effort.
2.1. Endpoint-to-Endpoint AD VPN Use Case
Two endpoints wish to communicate securely via a direct, point-to-
point Security Association (SA).
The need for secure endpoint to endpoint communications is often
driven by a need to employ high-bandwidth, low latency local
connectivity instead of using slow, expensive links to remote
gateways. For example, two users in close proximity may wish to
place a direct, secure video or voice call without needing to send
the call through remote gateways, which would add latency to the
call, consume precious remote bandwidth, and increase overall costs.
Such a use case also enables connectivity when both endpoints are
behind NAT gateways. Such use case should allow for seamless
connectivity even as endpoints roam, even if they are moving out from
behind a NAT gateway, from behind one NAT gateway to behind another,
or from a standalone position to behind a NAT gateway.
In a hub and spoke topology when two endpoints communicate, they must
use a mechanism for authentication, such that they do not expose them
to impersonation by the other spoke endpoint.
2.2. Gateway-to-Gateway AD VPN Use Case
A typical Enterprise traffic model follows a star topology, with the
gateways connecting to each other using IPsec tunnels.
However for the voice and other rich media traffic that requires a
lot of bandwidth or is performance sensitive, the traffic tromboning
to the hub can create traffic bottlenecks on the hub and can lead to
an increase in cost. A fully meshed solution is would make best use
of the available network capacity and performance but the deployment
of a fully meshed solution involves considerable configuration,
especially when a large number of nodes are involved. It is for this
purpose spoke-to-spoke tunnels are dynamically created and torn-down.
Hanna & Manral Expires June 10, 2013 [Page 5]
Internet-Draft Auto Discovery VPN December 2012
For the reasons of cost and manual error reduction, it is desired
that there be minimal configuration on each gateway.
The solution should work in cases where the endpoints are
administrated by separate management domains, albeit, ones that have
an existing trust relationship (for example two organisations who are
collaborating on a project, they may wish to join their networks,
whilst retaining independent control over configuration). It is
highly desirable that the solution works for the star, full mesh as
well as dynamic full mesh topology.
The solution should also address the case where gateways use dynamic
IP addresses.
Additionally, the routing implications of gateway-to-gateway
communication must be addressed. In the simple case, selectors
provide sufficient information for a gateway to forward traffic
appropriately. In other cases, additional tunneling (e.g., GRE) and
routing (e.g., OSPF) protocols are run over IPsec tunnels, and the
configuration impact on those protocols must be considered. There is
also the case when L3VPNs operate over IPsec Tunnels.
When two gateways communicate, they must use a mechanism for
authentication, such that they do not expose themselves to the risk
of impersonation by the other entities.
2.3. Endpoint-to-Gateway AD VPN Use Case
An endpoint should be able to use the most efficient gateway as it
roams in the internet.
A mobile user roaming on the Internet may connect to a gateway, which
because of roaming is no longer the most efficient gateway to use
(reasons could be cost/ efficiency/ latency or some other factor).
The mobile user should be able to discover and then connect to the
current most efficient gateway without having to reinitiate the
connection.
Hanna & Manral Expires June 10, 2013 [Page 6]
Internet-Draft Auto Discovery VPN December 2012
3. Inadequacy of Existing Solutions
Several solutions exist for the problems described above. However,
none of these solutions is adequate, as described here.
3.1. Exhaustive Configuration
One simple solution is to configure all gateways and endpoints in
advance with all the information needed to determine which gateway or
endpoint is optimal and to establish an SA with that gateway or
endpoint. However, this solution does not scale in a large network
with hundreds of thousands of gateways and endpoints, especially when
multiple organizations are involved and things are rapidly changing
(e.g. mobile endpoints). Such a solution is also limited by the
smallest endpoint/ gateway, as the same exhaustive configuration is
to be applied on all endpoints/ gateways. A more dynamic, secure and
scalable system for establishing SAs between gateways is needed.
3.2. Star Topology
The most common way to address a part of this this problem today is
to use what has been termed a "star topology". In this case one or a
few gateways are defined as "hub gateways", while the rest of the
systems (whether endpoints or gateways) are defined as "spokes". The
spokes never connect to other spokes. They only open tunnels with
the hub gateways. Also for a large number of gateways in one
administrative domain, one gateway may be defined as the hub, and the
rest of the gateways and remote access clients connect only to that
gateway.
This solution however is complicated by the case when the spokes use
dynamic IP addresses and DNS with dynamic updates must be used. It
is also desired that there is minimal to no configuration on the hub
as the number of spokes increases and new spokes are added and
deleted randomly.
Another problem with the star topology is that it creates a high load
on the hub gateways as well as on the connection between the spokes
and the hub. This load is both in processing power and in network
bandwidth. A single packet in the hub-and-spoke scenario can be
encrypted and decrypted multiple times. It would be much preferable
if these gateways and clients could initiate tunnels between them,
bypassing the hub gateways. Additionally, the path bandwidth to
these hub gateways may be lower than that of the path between the
spokes. For example, two remote access users may be in the same
building with high-speed wifi (for example, at an IETF meeting).
Channeling their conversation through the hub gateways of their
respective employers seems extremely wasteful, as well as having
Hanna & Manral Expires June 10, 2013 [Page 7]
Internet-Draft Auto Discovery VPN December 2012
lower bandwidth.
The challenge is to build a large scale, IPsec protected networks
that can dynamically change with minimum administrative overhead.
3.3. Proprietary Approaches
Several vendors offer proprietary solutions to these problems.
However, these solutions offer no interoperability between equipment
from one vendor and another. This means that they are generally
restricted to use within one organization, and it is harder to move
off such solutions as the features are not standardized. Besides
multiple organizations cannot be expected to all choose the same
equipment vendor.
Hanna & Manral Expires June 10, 2013 [Page 8]
Internet-Draft Auto Discovery VPN December 2012
4. Requirements
This sectiondefines the requirements, on which the solution will be
based.
4.1. Gateway and Endpoint Requirements
1. For any network topology (star, full mesh and dynamic full mesh)
gateways and endpoints MUST minimize configuration changes when a new
gateway or endpoint is added, removed or changed. Adding or removing
a spoke in the topology MUST NOT require configuration changes to the
hubs other than where the spoke was connected to and SHOULD NOT
require configuration changes to the hub the spoke was connected to.
The changes also MUST NOT require configuration changes in other
spokes.
Specifically, when evaluating potential proposals, we will compare
them by looking at how many endpoints or gateways must be
reconfigured when a new gateway or endpoint is added, removed, or
changed and how substantial this reconfiguration is, besides the
amount of static configuration required.
This requirement is driven by use cases 2.1 and 2.2 and by the
scaling limitations pointed out in section 3.1.
2. Gateways and endpoints MUST allow IPsec Tunnels to be setup
without any configuration changes, even when peer addresses get
updated every time the device comes up. This implies that SPD
entries or other configuration based on peer IP address will need to
be automatically updated, avoided, or handled in some manner to avoid
a need to manually update policy whenever an address changes.
This requirement is driven by use cases 2.1 and 2.2 and by the
scaling limitations pointed out in section 3.1.
3. In many cases additional tunneling protocols (e.g. GRE) or
Routing protocols (e.g. OSPF) are run over the IPsec tunnels.
Gateways MUST allow for the operation of tunneling and Routing
protocols operating over spoke-to-spoke IPsec Tunnels with minimal or
no, configuration impact. The ADVPN solution SHOULD NOT increase the
amount of information required to configure protocols running over
IPsec tunnels.
4. In the full mesh and dynamic full mesh topology, Spokes MUST
allow for direct communication with other spoke gateways and
endpoints. In the star topology mode, direct communication between
spokes MUST be disallowed.
Hanna & Manral Expires June 10, 2013 [Page 9]
Internet-Draft Auto Discovery VPN December 2012
This requirement is driven by use cases 2.1 and 2.2 and by the
limitations of a star topology pointed out in section 3.2.
5. One spoke MUST NOT be able to impersonate another spoke.
This requirement is driven by use case 2.1. Spokes become
compromised fairly often. The compromise of one Spoke should not
affect the security of other endpoints.
6. Gateways SHOULD allow for seamless handoff of sessions in case
endpoints are roaming, even if they cross policy boundaries. This
would mean the data traffic is minimally affected even as the handoff
happens. External factors like firewall, NAT box will not be
considered part of this solution.
This requirement is driven by use case 2.1. Today's endpoints are
mobile and transition often between different networks (from 4G to
WiFi and among various WiFi networks).
7. Gateways SHOULD allow for easy handoff of a session to another
gateway, to optimize latency, bandwidth, load balancing,
availability, or other factors, based on policy.
This requirement is driven by use case 2.3.
8. Gateways and endpoints MUST be able to work when they are behind
NAT boxes. It is especially difficult to handle cases where the Hub
is behind a NAT box, such a requirement MAY be supported. Where the
two endpoints are both behind separate NATs, communication between
these spokes SHOULD be supported. In the cases, workarounds MAY be
used such as port forwarding by the NAT or detecting when two spokes
are behind uncooperative NATs and using a hub in that case.
This requirement is driven by use cases 2.1 and 2.2. Endpoints are
often behind NATs and gateways sometimes are. IPsec should continue
to work seamlessly regardless, using AD VPN techniques whenever
possible and providing graceful fallback to hub and spoke techniques
as needed.
9. Changes such as establishing a new IPsec SA SHOULD be reportable
and manageable. However, creating a MIB or other management
technique is not within scope for this effort.
This requirement is driven by manageability concerns for all the use
cases, especially use case 2.2. As IPsec networks become more
dynamic, management tools become more essential.
10. To support allied and federated environments, endpoints and
Hanna & Manral Expires June 10, 2013 [Page 10]
Internet-Draft Auto Discovery VPN December 2012
gateways from different organizations SHOULD be able to connect to
each other.
11. The administrator of the ADVPN SHOULD allow for the
configuration of a Star, Full mesh or a partial full mesh topology,
based on which tunnels are allowed to be setup.
This requirement is driven by demand for all the use cases in
federated and allied environments.
12. The ADVPN solution SHOULD be able to scale for multicast
traffic.
This requirement is driven by the use case 2.2, where the amount of
rich media multicast traffic is increasing.
13. The ADVPN solution SHOULD allow for easy monitoring, logging and
reporting of the dynamic changes, to help for trouble shooting such
environments.
This requirement is driven by demand for all the use cases in
federated and allied environments.
14. The ADVPN solution MUST support Provider Edge (PE) based VPN's.
This requirement is driven by demand for all the use cases in
federated and allied environments.
Hanna & Manral Expires June 10, 2013 [Page 11]
Internet-Draft Auto Discovery VPN December 2012
5. Security Considerations
The solution to the problems presented in this draft may involve
dynamic updates to databases defined by RFC 4301, such as the
Security Policy Database (SPD) or the Peer Authorization Database
(PAD).
RFC 4301 is silent about the way these databases are populated, and
it is implied that these databases are static and pre-configured by a
human. Allowing dynamic updates to these databases must be thought
out carefully, because it allows the protocol to alter the security
policy that the IPsec endpoints implement.
One obvious attack to watch out for is stealing traffic to a
particular site. The IP address for www.example.com is 192.0.2.10.
If we add an entry to an IPsec endpoint's SPD that says that traffic
to 192.0.2.10 is protected through peer Gw-Mallory, then this allows
Gw-Mallory to either pretend to be www.example.com or to proxy and
read all traffic to that site. Updates to this database requires a
clear trust model.
More to be added.
Hanna & Manral Expires June 10, 2013 [Page 12]
Internet-Draft Auto Discovery VPN December 2012
6. IANA Considerations
No actions are required from IANA for this informational document.
Hanna & Manral Expires June 10, 2013 [Page 13]
Internet-Draft Auto Discovery VPN December 2012
7. Acknowledgements
Many people have contributed to the development of this problem
statement and many more will probably do so before we are done with
it. While we cannot thank all contributors, some have played an
especially prominent role. Yoav Nir, Yaron Scheffer, Jorge Coronel
Mendoza, Chris Ulliott, and John Veizades wrote the document upon
which this draft was based. Geoffrey Huang, Suresh Melam, Praveen
Sathyanarayan, Andreas Steffen, Brian Weis, and Lou Berger provided
essential input.
Hanna & Manral Expires June 10, 2013 [Page 14]
Internet-Draft Auto Discovery VPN December 2012
8. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
Hanna & Manral Expires June 10, 2013 [Page 15]
Internet-Draft Auto Discovery VPN December 2012
Authors' Addresses
Steve Hanna
Juniper Networks, Inc.
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
USA
Email: shanna@juniper.net
Vishwas Manral
Hewlett-Packard Co.
19111 Pruneridge Ave.
Cupertino, CA 95113
USA
Email: vishwas.manral@hp.com
Hanna & Manral Expires June 10, 2013 [Page 16]