Network Working Group
Internet Draft Tomonori Takeda (Editor)
Intended Status: Informational NTT
Expires: January 2008 July 2007
Applicability Statement for Layer 1 Virtual Private Networks (L1VPNs)
Basic Mode
draft-ietf-l1vpn-applicability-basic-mode-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document provides an applicability statement on the use of
Generalized Multiprotocol Label Switching (GMPLS) protocols and
mechanisms to support Basic Mode Layer 1 Virtual Private Networks
(L1VPNs).
L1VPNs provide customer services and connectivity at layer 1 over
layer 1 networks. The operation of L1VPNs is divided into the Basic
Mode and the Enhanced Mode where the Basic Mode of operation does not
feature any exchange of routing information between the layer 1
network and the customer domain. This document examines how GMPLS
T.Takeda, et al. Expires January 2008 [Page 1]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
protocols can be used to satisfy the requirements of a Basic Mode
L1VPN.
Table of Contents
1. Introduction...................................................2
1.1 Terminology...................................................3
2. Basic Mode Overview............................................3
3. Supported Network Types........................................4
3.1 Data Plane....................................................4
3.2 Control Plane.................................................4
4. Addressing.....................................................5
5. Provider Control of its Infrastructure.........................5
5.1 Provisioning Model............................................5
5.2 PE-PE Segment Control.........................................6
5.2.1 Path Computation and Establishment..........................6
5.2.2 Resource Management.........................................7
5.2.3 Consideration of CE-PE TE information.......................7
5.3 Connectivity Restriction......................................8
6. Customer Control of its VPN....................................8
6.1 Topology Control..............................................8
6.2 Note on Routing...............................................8
7. Scalability, Resiliency........................................9
7.1 Scalability...................................................9
7.2 Data Plane Resiliency........................................10
7.3 Control Plane Resiliency.....................................11
8. Security......................................................11
8.1 Topology Confidentiality.....................................11
8.2 External Control of the Provider Network.....................12
8.3 Data Plane Security..........................................12
8.4 Control Plane Security.......................................13
9. Manageability Considerations..................................14
10. IANA Considerations..........................................14
11. References...................................................14
11.1 Normative References........................................14
11.2 Informative References......................................15
12. Acknowledgments..............................................16
13. Authors' Addresses...........................................16
14. Intellectual Property Consideration..........................17
15. Full Copyright Statement.....................................17
1. Introduction
This document provides an applicability statement on the use of
Generalized Multiprotocol Label Switching (GMPLS) protocols and
mechanisms to Basic Mode Layer 1 Virtual Private Networks (L1VPNs) as
specified in [RFC4847].
T.Takeda, et al. Expires January 2008 [Page 2]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
The operation of L1VPNs is divided into the Basic Mode and the
Enhanced Mode. The Basic Mode of operation does not feature any
exchange of routing information between the layer 1 network and the
customer domain, while the Enhanced Mode of operation features
exchange of routing information between the layer 1 network and the
customer domain.
The main GMPLS protocols and mechanisms applicable to the L1VPN Basic
Mode are [L1VPN-BM], [L1VPN-BGP-DISC], and [L1VPN-OSPF-DISC], along
with several other documents referenced within this document.
Note that discussion in this document is focused on areas where GMPLS
protocols and mechanisms are relevant.
1.1 Terminology
The reader is assumed to be familiar with the terminology in
[RFC3031], [RFC3209], [RFC3471], [RFC3473], [RFC4202], [RFC4026] and
[RFC4847].
2. Basic Mode Overview
As described in [RFC4847], in the Basic Mode service model, there is
no routing exchange between the CE and the PE. CE-CE VPN connections
are set up by GMPLS signaling between the CE and the PE, and then
across the provider network. A VPN connection is limited to the
connection between CEs belonging to the same VPN.
Note that in L1VPNs, routing operates within the provider network and
may be used by PEs to exchange information specific to the VPNs
supported by the provider network (e.g., membership information).
In the L1VPN Basic Mode, the provider network is completely under the
control of the provider. This includes the PE-PE segment of the CE-CE
VPN connection that is controlled and computed by the provider (PE-PE
segment control). On the other hand, the VPN itself, constructed from
a set of CEs and the VPN connections provided by the provider, is
under the control of each customer. This includes that a customer can
request between which CEs a connection is to be established (topology
control). Note that a customer may outsource the management of its
VPN to a third party, including to the provider itself. There is a
confidentiality requirement between the provider and each customer.
[L1VPN-BM], which extends [RFC4208], specifies GMPLS signaling to
establish CE-CE VPN connections.
[L1VPN-BGP-DISC] and [L1VPN-OSPF-DISC] specify alternative mechanisms
to exchange L1VPN membership information between PEs, based on BGP
and OSPF respectively.
T.Takeda, et al. Expires January 2008 [Page 3]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
3. Supported Network Types
3.1 Data Plane
The provider network can be constructed from any type of layer 1
switches, such as Time Division Multiplexing (TDM) switches, Optical
Cross-Connects (OXCs), or Photonic Cross-Connects (PXCs).
Furthermore, a PE may be an Ethernet Private Line (EPL) type of
device, that maps Ethernet frames onto layer 1 connections (by means
of Ethernet over TDM etc.). The provider network may be constructed
from switches providing a single switching granularity (e.g., only
VC3 switches), or from switches providing multiple switching
granularities (e.g., from VC3/VC4 switches, or from VC3 switches and
OXCs). The provider network may provide a single type of VPN
connection (e.g., VC3 connections only), or multiple types of
connection (e.g., VC3/VC4 connections, or VC3 connections and
wavelength connections).
A CE does not have to have the capability to switch at layer 1, but
it must be capable of receiving a layer 1 signal and either switching
it or terminating it with adaptation.
As described in [RFC4847] and [L1VPN-BM], a CE and a PE are connected
by one or more links. A CE may also be connected to more than one PE,
and a PE may have more than one CE connected to it.
A CE may belong to a single VPN, or to multiple VPNs, and a PE may
support one or more VPNs through a single CE or through multiple CEs.
3.2 Control Plane
The provider network is controlled by GMPLS. L1VPN Basic Mode
provider networks are limited to a single AS within the scope of this
document. Multi-AS Basic Mode L1VPNs are for future study.
As described in [RFC4847] and [L1VPN-BM], a CE and a PE need to be
connected by at least one control channel. It is necessary to
disambiguate control plane messages exchanged between a CE and a PE
if the CE-PE relationship is applicable to more than one VPN. This
makes it possible to determine to which VPN such control plane
messages apply. Such disambiguation can be achieved by allocating a
separate control channel to each VPN (either using a separate
physical channel, a separate logical channel such as an IP tunnel, or
using separate addressing).
GMPLS allows any type of control channel to be used, as long as there
is IP level reachability. In the L1VPN context, instantiation of a
T.Takeda, et al. Expires January 2008 [Page 4]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
control channel between a CE and a PE may differ depending on
security requirements, etc. This is discussed in Section 8.
4. Addressing
As described in [L1VPN-BM], the L1VPN Basic Mode allows that customer
addressing realms overlap with each other, and also overlap with the
service provider addressing realm. That is, a customer network may
re-use addresses used by the provider network, and may re-use
addresses used in another customer network supported by the same
provider network. This is the same as in any other VPN model.
In addition, the L1VPN Basic Mode allows a CE-PE control channel
addressing realm overlap. That is, a CE-PE control channel address
(CE's address of this control channel and PE's address of this
control channel) is unique within the VPN they belong, but not
necessarily unique across multiple VPNs.
Furthermore, once a VPN connection has been established, the L1VPN
Basic Mode does not enforce any restriction on address assignment for
this VPN connection (treated as a link) for customer network
operation (e.g., IP network, MPLS network).
5. Provider Control of its Infrastructure
5.1 Provisioning Model
As described in [L1VPN-BM], for each VPN that has at least one
customer-facing port on a given PE, the PE maintains a Port
Information Table (PIT) associated with that VPN. A PIT provides a
cross-reference between Customer Port Indices (CPIs) and Provider
Port Indices (PPIs) and contains a list of <CPI, PPI> tuples for all
the ports within the VPN. In addition, for local PE ports of a given
VPN the PE retains an identifier known as the VPN-PPI, and this is
stored in the PIT with the <CPI, PPI> tuples.
When a new CE belonging to one or more VPNs is added to a PE, PIT
entries associated to those VPNs need to be configured on the PE.
Section 4 of [L1VPN-BM] specifies such procedures:
- If no PIT exists for the VPN on the PE, a new PIT is created by the
provider and associated with the VPN identifier.
- The PIT (new or pre-existing) is updated to include information
related to the newly added CE. The VPN-PPI, PPI, and CPI are
installed in the PIT. Note that the PPI is well-known by the PE,
but the CPI must be discovered either through manual configuration
or automatically by mechanisms such as the Link Management Protocol
(LMP) [RFC4204]. In addition, a CE to PE control channel needs to
T.Takeda, et al. Expires January 2008 [Page 5]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
be configured.
- The updated PIT information needs to be configured in the PITs on
remote PE associated with the VPN. For such purpose, manual
configuration, or some sort of auto-discovery mechanisms can be
used. [L1VPN-BGP-DISC] and [L1VPN-OSPF-DISC] specifies alternative
auto-discovery mechanisms.
- In addition, remote PIT information associated with the VPN needs
to be configured on this PE if the PIT has been newly created.
Again, this can be achieved through manual configuration or through
auto-discovery, [L1VPN-BGP-DISC] and [L1VPN-OSPF-DISC].
When VPN membership of an existing CE changes, or when a CE is
removed from a PE, similar procedures need to be applied to update
the local and remote PITs.
5.2 PE-PE Segment Control
In the L1VPN Basic Mode, a PE-PE segment of a CE-CE VPN connection is
completely under the control of provider network.
5.2.1 Path Computation and Establishment
A PE-PE segment of a CE-CE VPN connection may be established based on
various policies. Those policies can be applied per VPN or per VPN
connection. The policy is configured by the provider, possibly based
on the contracts with each customer.
Examples of PE-PE segment connection establishment polices supported
in the L1VPN Basic Mode are as follows.
- Policy 1: On-demand establishment, on-demand path computation
- Policy 2: On-demand establishment, pre-computed path
- Policy 3: Pre-establishment, pre-computed path
In each policy, the PE-PE path may be computed by the local PE, or by
a path computation entity outside of the local PE (e.g., a Path
Computation Element (PCE) [RFC4655], or management systems).
In policies 2 and 3, pre-computation of paths (and pre-establishment
if applicable) can be done at the network planning phase, or just
before signaling (e.g., triggered by an off-line customer request).
As the result of pre-computation (and pre-establishment), there could
be multiple PE-PE segments for a specific pair of PEs. When a PE
receives a Path message from a CE for a VPN connection, a PE needs to
determine which PE-PE segment to use. In such cases, the provider may
want to control:
T.Takeda, et al. Expires January 2008 [Page 6]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
- Which VPN uses which PE-PE VPN segment.
- Which CE-CE VPN connection uses which PE-PE VPN segment.
The former requires mapping between the PIT and the PE-PE segment.
The latter requires some more sophisticated mapping method, for
example:
- Mapping between individual PIT entries and PE-PE segments.
- Use of a Path Key ID [Conf-Segment] supplied by the provider to the
CE, and signaled by the CE as part of the VPN connection request.
The L1VPN Basic Mode does not preclude usage of other methods, if
applicable.
In policy 3, stitching or nesting is necessary in order to map the
CE-CE VPN connection to a pre-established PE-PE segment.
5.2.2 Resource Management
The provider network may operate resource management based on various
policies. These policies can be applied per VPN or per VPN
connection. The policy is configured by the provider, possibly based
on the contracts with each customer.
For example, a provider may choose to partition the resources of the
provider network for limited use by different VPNs or customers. Such
a function might be achieved within the scope of the Basic Mode using
resource affinities [RFC3209], but the details of per-VPN resource
models (especially in terms of CE-PE routing) are considered as part
of the Enhanced Mode.
5.2.3 Consideration of CE-PE TE information
[L1VPN-OSPF-DISC] and [BGP-TE] allow CE-PE TE link information to be
injected into the provider network. This may be helpful for the
ingress PE to prevent connection setup failure due to lack of
resources or incompatible switching capabilities on remote CE-PE TE
links.
Furthermore, the L1VPN Basic Mode allows a remote CE to be reached
through more than one TE link connected to the same PE (single-homed)
or to different PEs (dual-homed). In such cases, to facilitate route
choice, the ingress CE needs to initiate signaling by specifying the
egress CE's router ID not the egress CPI in the Session Object and
ERO (if present) so as to not constrain the choice of route within
the provider network. Therefore, the CE's router ID needs to be
configured in the PITs.
T.Takeda, et al. Expires January 2008 [Page 7]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
Note that, as described in Section 7.2, consideration of the full
feature set enabled by dual-homing (such as resiliency) is out of
scope of the L1VPN Basic Mode.
5.3 Connectivity Restriction
The L1VPN Basic Mode allows restricting connection establishment
between CEs belonging to the same VPN for policy reasons (including
VPN security). Since the PIT at each PE is associated with a VPN,
this function can be easily supported. The restriction can be applied
at the ingress PE or at the egress PE according to the applicable
restriction policy, but note that applying the policy at the egress
may waste signaling effort within the network as VPN connections are
pointlessly attempted.
In addition, the L1VPN Basic Mode does not restrict use of any
advanced admission control based on various policies.
6. Customer Control of its VPN
6.1 Topology Control
In the L1VPN Basic Mode, VPN connection topology is controlled by the
customer. That is, a customer can request setup/deletion/modification
of VPN connections using signaling mechanisms specified in
[L1VPN-BM].
Also note that if there are multiple CE-PE TE links (single-homed or
multi-homed), a customer can specify which CE-PE TE link to use to
support any VPN connection. Alternatively, a customer may let the
provider choose the CE-PE TE link at the egress side, as described in
Section 5.2.3.
6.2 Note on Routing
A CE needs to obtain the remote CPI to which it wishes to request a
connection. Since, in the L1VPN Basic Mode, there is no routing
information exchange between a CE and a PE, there is no dynamic
mechanism supported as part of the Basic Mode L1VPN service, and the
knowledge of remote CPIs must be acquired in a VPN-specific way,
perhaps through configuration or through a directory server.
If a VPN is used by a customer to operate a private IP network, the
customer may wish to form routing adjacencies over the CE-CE VPN
connections. The L1VPN Basic Mode does not enforce any restriction on
such operation by a customer, and the use made of the VPN connections
is transparent to the provider network.
T.Takeda, et al. Expires January 2008 [Page 8]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
Furthermore, if a VPN is used by a customer to operate a private
Multiprotocol Label Switching (MPLS) or GMPLS network, the customer
may wish to treat a VPN connection as a Traffic Engineering (TE)
link, and this requires a CE-CE control channel. Note that a
Forwarding Adjacency [RFC4206] cannot be formed from the CE-CE VPN
connection in the Basic Mode because there is no routing exchange
between CE and PE - that is, the customer network and the provider
network do not share a routing instance, and the customer control
channel cannot be carried within the provider control plane. But
where the CE provides suitable adaptation (for example, where the
customer network is a packet-switched MPLS or GMPLS network) the
customer control channel may be in-band and a routing adjacency may
be formed between the CEs using the VPN connection. Otherwise, CE-CE
control plane connectivity may form part of the L1VPN service
provided to the customer by the provider and may be achieved within
the L1VPN connection (for example, through the use of overhead bytes)
or through a dedicated control channel connection or tunnel. The
options available are discussed further in Section 10.2 of
[RFC4847].
7. Scalability, Resiliency
7.1 Scalability
There are several factors that impact scalability.
o Number of VPNs (PITs) configured on each PE
With the increase of this number, information to be maintained on
the PE increases. Theoretically, the upper limit of the number of
VPNs supported in a provider network is governed by how the ID
associated with a VPN is allocated, and the number of PITs
configured on each PE is limited by this number. However,
implementations may impose arbitrary limits on the number of PITs
supported by any one PE.
o Number of CE-PE TE links for each VPN
With the increase of this number, information to be maintained in
each PIT increases. When auto-discovery mechanisms are used, the
amount of information that an auto-discovery mechanism can support
may restrict this number.
Note that [L1VPN-OSPF-DISC] floods membership information not only
among PEs, but also to all P nodes. This may lead to scalability
concerns, compared to [L1VPN-BGP-DISC], which distributes
membership information only among PEs. Alternatively, a separate
instance of the OSPF protocol can be used just between PEs for
distributing membership information. In such a case, Ps do not
T.Takeda, et al. Expires January 2008 [Page 9]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
participate in flooding.
Note that in the L1VPN Basic Mode, a PE needs to obtain only CE-PE
TE link information, and not customer routing information, which is
quite different from the mode of operation of a L3VPN. Therefore,
the scalability concern is considered to be less problematic.
o Number of VPN connections
With the increase of this number, information to be maintained on
each PE/P increases. When stitching or nesting is used, state to
be maintained at each PE increases compared to when connectivity is
achieved without stitching or nesting.
However, in a layer 1 core, this number is always bounded by the
available physical resource because each LSP uses a separate label
which is directly bound to a physical, switchable resource
(timeslot, lambda, fiber). Thus, it can be safely assumed that the
PEs/Ps can comfortably handle the number of LSPs that they may be
called on to switch for a L1VPN.
7.2 Data Plane Resiliency
The L1VPN Basic Mode supports following data plane recovery
techniques [L1VPN-BM].
o PE-PE segment recovery
The CE indicates to protect the PE-PE segment by including
Protection Object specified in [RFC4873] in the Path message and
setting Segment Recovery Flags. The CE may also indicate the branch
and merge nodes by including Secondary Explicit Route Object.
Depending on the signaling mechanisms used within the provider
network, details on how to protect the PE-PE segment may differ as
follows.
- If LSP stitching or LSP hierarchy are used to provision the PE-PE
segment, then the PE-PE LSP may be protected using end-to-end
recovery within the provider network.
- If the CE-CE VPN connection is a single end-to-end LSP (including
if session shuffling is used), then the PE-PE LSP segment may be
protected using segment protection [RFC4873]
o CE-PE recovery and PE-PE recovery via link protection
The CE indicates to protect ingress and egress CE-PE links as well
as links within the provider network by including Protection Object
T.Takeda, et al. Expires January 2008 [Page 10]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
specified in [RFC3473] and setting Link Flags in the Path message.
- The ingress and egress CE-PE link may be protected at a lower
layer
Depending on the signaling mechanisms used within the provider
network, details on how to protect links within the provider
network may differ as follows.
- If the PE-PE segment is provided as a single TE link (stitching
or hierarchy) so that the provider network can perform simple PE-
to-PE routing, then the TE link may offer link-level protection
through the instantiation of multiple PE-PE LSPs.
- The PE-PE segment may be provisioned using only link-protected
links within the core network.
Note that it is not possible to protect only the CE-PE portion or the
PE-PE portion by link protection because the CE-CE signaling request
asks for a certain level of link protection on all links used by the
LSP. Also, it is not possible to protect the CE-PE portion by link
recovery and the PE-PE portion by segment recovery at the same time.
CE-CE recovery through the use of connections from one CE to diverse
PEs (i.e., dual-homing) is not supported in the L1VPN Basic Mode.
7.3 Control Plane Resiliency
The L1VPN Basic Mode allows use of GMPLS control plane resiliency
mechanisms. This includes, but not limited to, control channel
management in LMP [RFC4204] and fault handling in RSVP-TE ([RFC3473]
and [RSVP-GR]) between a CE and a PE as well as within the provider
network.
8. Security
Security considerations are described in [RFC4847], and this section
describes how these considerations are addressed in the L1VPN Basic
Mode.
8.1 Topology Confidentiality
As specified in [L1VPN-BM], a provider's topology confidentiality is
preserved by the Basic Mode. Since there is no routing exchange
between PE and CE, the customer network can gather no information
about the provider network. Further, as described in Section 4 of
[RFC4208], a PE may filter the information present in a Record Route
Object (RRO) that is signaled from the provider network to the
customer network. In addition, as described in Section 5 of [RFC4208]
T.Takeda, et al. Expires January 2008 [Page 11]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
and Section 4.4 of [L1VPN-BM], when a Notify message is sent to a CE,
it is possible to hide the provider internal address. This is
accomplished by a PE updating the Notify Node Address with its own
address when the PE receives NOTIFY_REQUEST object from the CE.
Even in the case of pre-computed and/or pre-signaled PE-PE segments,
provider topology confidentiality may be preserved through the use of
path key IDs [Conf-Segment].
The customer's topology confidentiality cannot be completely hidden
from the provider network. At the least, the provider network will
know about the addresses and locations of CEs. Other customer
topology information will remain hidden from the provider in the
Basic Mode although care may be needed to protect the customer
control channel as described in Section 8.4.
The provider network is responsible for maintaining confidentiality
of topology information between customers and across VPNs. Since
there is no distribution of routing information from PE to CE in the
Basic Mode, there is no mechanism by which the provider could
accidentally, or deliberately but automatically, distribute this
information.
8.2 External Control of the Provider Network
The provider network is protected from direct control from within
customer networks through policy and through filtering of signaling
messages.
There is a service-based policy installed at each PE that directs how
a PE should react to a VPN connection request received from any CE.
Each CE is configured at the PE (or through a policy server) for its
membership of a VPN, and so CEs cannot dynamically bind to a PE or
join a VPN. With this configuration comes the policy that tells the
PE how to react to a VPN connection request (for example, whether to
allow dynamic establishment of PE-PE connections). Thus, the provider
network is protected against spurious VPN connection requests and can
charge for all VPN connections according to the service agreement
with the customers. Hence the provider network is substantially
protected against denial of service attacks.
At the same time, if a Path message from a CE contains an Explicit
Route Object (ERO) specifying the route within provider network, it
is rejected by the PE. Thus, the customer network has no control over
the resources in the provider network.
8.3 Data Plane Security
T.Takeda, et al. Expires January 2008 [Page 12]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
As described in [RFC4847], at layer 1, data plane information is
normally assumed to be secure once connections are established since
those connections are dedicated VPNs. That is, it is not possible to
communicate unless there is a connection.
In order to protect against mis-delivery, each VPN connection is
restricted to use only within a single VPN. That is, a VPN connection
does not connect CEs that are in different VPNs. In order to realize
this, the identity of CEs is assured as part of the service contract.
And upon receipt of a request for connection setup, the provider
network assures that the connection is requested between CEs
belonging to the same VPN. This is achieved as described in Section
5.3.
Furthermore, customers can apply their own security mechanisms to
protect data plane information (CE-CE security). This includes IPsec
for IP traffic.
8.4 Control Plane Security
There are two aspects for control plane security.
First, the entity connected over a CE-PE control channel must be
identified. This is done when a new CE is added as part of the
service contract and the necessary control channel is established.
This identification can use authentication procedures available in
RSVP-TE [RFC3209].
Second, it must be possible to secure communication over a CE-PE
control channel. If a communication channel between the customer and
the provider (control channel, management interface) is physically
separate per customer, the communication channel could be considered
as secure. However, when the communication channel is physically
shared among customers, security mechanisms need to be available and
should be enforced. RSVP-TE [RFC3209] provides for tamper-protection
of signaling message exchanges. IPsec tunnels can further be used for
this purpose.
Note that even in the case of physically separate communication
channels, customers may wish to apply security mechanisms, such as
IPsec, to assure higher security, and such mechanisms must be
available.
Furthermore, the provider network need mechanisms to detect Denial of
Service (DoS) attacks and to protect against them reactively and
proactively. In the Basic Mode, this relies on management system(s).
Lastly, it should be noted that customer control plane traffic
carried over the provider network between CEs needs to be protected.
T.Takeda, et al. Expires January 2008 [Page 13]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
Such protection is normally the responsibility of the customer
network and can use the security mechanisms of the customer signaling
and routing protocols (for example, RSVP-TE [RFC3209]) or may use
IPsec tunnels between CEs. CE-CE control plane security may form part
of the data plane protection where the control plane traffic is
carried in-band in the VPN connection. Where the CE-CE control plane
connectivity is provided as an explicit part of the L1VPN service by
the provider, control plane security should form part of the service
agreement between the provider and customer.
9. Manageability Considerations
Manageability considerations are described in [RFC4847]. In the L1VPN
Basic Mode, we rely on management system(s) for various aspects of
the different service functions, such as fault management,
configuration and policy management, accounting management,
performance management, and security management (as described in
Section 8).
In order to support various management functionalities, MIB modules
need to be supported. In particular, the GMPLS TE MIB (GMPLS-TE-STD-
MIB) [RFC4802] can be used for GMPLS-based traffic engineering
configuration and management, while the TE Link MIB (TE-LINK-STD-MIB)
[RFC4220] can be used for TE links configuration and management.
10. IANA Considerations
This informational document makes no requests for IANA action.
[RFC Editor - please remove this entire section before publication]
11. References
11.1 Normative References
[RFC4847] Takeda, T., Editor "Framework and Requirements for
Layer 1 Virtual Private Networks", RFC 4847, April
2007.
[RFC4208] Swallow, G., et al., "Generalize Multiprotocol
Label Switching(GMPLS) User-Network Interface:
Resource ReserVation Protocol-Traffic Engineering
(RSVP-TE) Support for the Overlay Model," RFC4208,
October 2005.
[L1VPN-BM] Fedyk, D., and Rekhter, Y., Editors, "Layer 1
VPN Basic Mode", draft-ietf-l1vpn-basic-mode,
work in progress.
[L1VPN-BGP-DISC] Ould-Brahim, H., Fedyk, D., and Rekhter, Y.,
T.Takeda, et al. Expires January 2008 [Page 14]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
"BGP-based Auto-Discovery for L1VPNs", draft-ietf-
l1vpn-bgp-auto-discovery, work in progress.
[L1VPN-OSPF-DISC] Bryskin, I., and Berger, L., "OSPF Based L1VPN
Auto-Discovery", draft-ietf-l1vpn-ospf-auto-
discovery, work in progress.
[RFC4873] Berger, L., et al., "GMPLS Based Segment
Recovery", RFC 4873, May 2007.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V. and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
11.2 Informative References
[RFC3031] Rosen, E., Viswanathan, A. and R. Callon,
"Multiprotocol label switching Architecture", RFC
3031, January 2001.
[RFC3471] Berger, L., Editor, "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
[RFC3473] Berger, L., Editor "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling - Resource
ReserVation Protocol-Traffic Engineering (RSVP-TE)
Extensions", RFC 3473, January 2003.
[RFC4202] Kompella, K., et al., "Routing Extensions in
Support of Generalized Multi-Protocol Label
Switching (GMPLS)", RFC 4202, October 2005.
[RFC4204] Lang, J., "Link Management Protocol (LMP)",
RFC 4204, October 2005.
[RFC4026] Anderssion, L., and Madsen, T., "Provider
Provisioned Virtual Private Network (VPN)
Terminology", RFC 4026, March 2005.
[RFC4206] Kompella, K., Rekhter, Y., "Label Switched Paths
(LSP) Hierarchy with Generalized Multi-Protocol
Label Switching (GMPLS) Traffic Engineering (TE)",
RFC 4206, October 2005.
[BGP-TE] Ould-Brahim, H., Fedyk, D., and Rekhter, Y.,
"Traffic Engineering Attribute", draft-fedyk-bgp-
te-attribute, work in progress.
T.Takeda, et al. Expires January 2008 [Page 15]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
[RFC4655] Farrel, A., Vasseur, JP, Ash, J., "Path
Computation Element (PCE) Architecture", RFC 4655,
August 2006.
[Conf-Segment] Bradford, R., Editor, "Preserving Topology
Confidentiality in Inter-Domain Path Computation
and Signaling", draft-ietf-pce-path-key, work in
progress.
[RFC4802] Nadeau, T., Farrel, A., Editors, "Generalized
Multiprotocol Label Switching (GMPLS) Traffic
Engineering Management Information Base", RFC
4802, February 2007.
[RFC4220] Dubuc, M., Nadeau, T., Lang, J., "Traffic
Engineering Link Management Information Base", RFC
4220, November 2005.
[RSVP-GR] Satyanarayana, A., and Rahman, R., "Extensions to
GMPLS RSVP Graceful Restart", draft-ietf-ccamp-
rsvp-restart-ext, work in progress.
12. Acknowledgments
Authors would like to thank Ichiro Inoue for valuable comments. In
addition, authors would like to thank Marco Carugi and Takumi Ohba
for valuable comments in the early development of this document.
13. Authors' Addresses
Deborah Brungard (AT&T)
Rm. D1-3C22 - 200 S. Laurel Ave.
Middletown, NJ 07748, USA
Phone: +1 732 4201573
Email: dbrungard@att.com
Adrian Farrel
Old Dog Consulting
Phone: +44 (0) 1978 860944
Email: adrian@olddog.co.uk
Hamid Ould-Brahim
Nortel Networks
P O Box 3511 Station C
Ottawa, ON K1Y 4H7 Canada
Phone: +1 (613) 765 3418
Email: hbrahim@nortel.com
T.Takeda, et al. Expires January 2008 [Page 16]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
Dimitri Papadimitriou (Alcatel-Lucent)
Francis Wellensplein 1,
B-2018 Antwerpen, Belgium
Phone: +32 3 2408491
Email: dimitri.papadimitriou@alcatel-lucent.be
Tomonori Takeda
NTT Network Service Systems Laboratories, NTT Corporation
3-9-11, Midori-Cho
Musashino-Shi, Tokyo 180-8585 Japan
Phone: +81 422 59 7434
Email: takeda.tomonori@lab.ntt.co.jp
14. Intellectual Property Consideration
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed
to pertain to the implementation or use of the technology
described in this document or the extent to which any license
under such rights might or might not be available; nor does it
represent that it has made any independent effort to identify any
such rights. Information on the procedures with respect to
rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository
at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights that may cover technology that may be required
to implement this standard. Please address the information to the
IETF at ietf-ipr@ietf.org.
15. Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and
restrictions contained in BCP 78, and except as set
forth therein, the authors retain all their rights.
This document and the information contained herein are provided
on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY,
THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE
T.Takeda, et al. Expires January 2008 [Page 17]
draft-ietf-l1vpn-applicability-basic-mode-02.txt July 2007
DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
T.Takeda, et al. Expires January 2008 [Page 18]