L2TPEXT Working Group M. Konstantynowicz, Ed.
Internet-Draft G. Heron, Ed.
Intended status: Standards Track Cisco Systems
Expires: August 22, 2015 R. Schatzmayr
Deutsche Telekom AG
W. Henderickx
Alcatel-Lucent, Inc.
February 18, 2015
Keyed IPv6 Tunnel
draft-ietf-l2tpext-keyed-ipv6-tunnel-02
Abstract
This document describes a simple L2 Ethernet over IPv6 tunnel
encapsulation with mandatory 64-bit cookie for connecting L2 Ethernet
attachment circuits identified by IPv6 addresses. The encapsulation
is based on L2TPv3 over IP.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 22, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
Konstantynowicz, et al. Expires August 22, 2015 [Page 1]
Internet-Draft February 2015
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Static 1:1 Mapping Without a Control Plane . . . . . . . . . 3
3. 64-bit Cookie . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Encapsulation . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Fragmentation and Reassembly . . . . . . . . . . . . . . . . 7
6. OAM Considerations . . . . . . . . . . . . . . . . . . . . . 7
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
8. Security Considerations . . . . . . . . . . . . . . . . . . . 8
9. Contributing Authors . . . . . . . . . . . . . . . . . . . . 8
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 9
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 9
11.1. Normative References . . . . . . . . . . . . . . . . . . 9
11.2. Informative References . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10
1. Introduction
L2TPv3, as defined in RFC3931 [RFC3931], provides a dynamic mechanism
for tunneling Layer 2 (L2) "circuits" across a packet-oriented data
network (e.g., over IP), with multiple attachment circuits
multiplexed over a single pair of IP address endpoints (i.e. a
tunnel) using the L2TPv3 session ID as a circuit discriminator.
Implementing L2TPv3 over IPv6 provides the opportunity to utilize
unique IPv6 addresses to identify Ethernet attachment circuits
directly, leveraging the key property that IPv6 offers, a vast number
of unique IP addresses. In this case, processing of the L2TPv3
Session ID may be bypassed upon receipt as each tunnel has one and
only one associated session. This local optimization does not hinder
the ability to continue supporting the multiplexing of circuits via
the Session ID on the same router for other L2TPv3 tunnels.
Konstantynowicz, et al. Expires August 22, 2015 [Page 2]
Internet-Draft February 2015
2. Static 1:1 Mapping Without a Control Plane
Static local configuration creates a one-to-one mapping between the
access-side L2 attachment circuit and the IP address used in the
network-side IPv6 encapsulation. The L2TPv3 Control Plane defined in
RFC3931 is not used.
The IPv6 L2TPv3 tunnel encapsulating device uniquely identifies each
Ethernet L2 attachment connection by a port ID or a combination of
port ID and VLAN ID(s) on the access side, and by an IPv6 address on
the network side.
Any service-delimiting IEEE 802.1Q [IEEE802.1Q] or IEEE 802.1ad
[IEEE802.1ad] VLAN IDs - S-tag, C-tag or tuple (S-tag, C-tag) - are
treated with local significance within the Ethernet L2 port and are
not forwarded over the IPv6 L2TPv3 tunnel. The IPv6 address is
treated as the identifier of the IPv6 L2TPv3 tunnel endpoint.
Certain deployment scenarios may require using a single IPv6 address
to identify a tunnel endpoint for multiple IPv6 L2TPv3 tunnels. For
such cases the tunnel encapsulating device identifies each tunnel by
a unique combination of tunnel source and destination IPv6 addresses.
As mentioned above Session ID processing is not required as each
keyed IPv6 tunnel has one and only one associated session. However
for compatibility with existing RFC3931 implementations, the packets
need to be sent with Session ID. The router implementing L2TPv3
according to RFC3931 can be configured with multiple L2TPv3 tunnels,
with one session per tunnel, to interoperate with the router
implementing the keyed IPv6 tunnel as specified by this document.
Note that a previous IETF draft [I.D.ietf-pppext-l2tphc] introduces
the concept of an L2TP tunnel carrying a single session and hence not
requiring session ID processing.
3. 64-bit Cookie
In line with RFC3931, the 64-bit cookie is used for additional tunnel
endpoint context check. All packets MUST carry the 64-bit L2TPv3
cookie field. The cookie MUST be 64 bits long in order to provide
sufficient protection against spoofing and brute force blind
insertion attacks. The cookie values SHOULD be randomly selected.
In the absence of the L2TPv3 Control Plane, the L2TPv3 encapsulating
router must be provided with local configuration of the 64-bit cookie
for each local and remote IPv6 endpoint - note that cookies are
asymmetric, so local and remote endpoints may send different cookie
values, and in fact SHOULD do so. The value of the cookie MUST be
Konstantynowicz, et al. Expires August 22, 2015 [Page 3]
Internet-Draft February 2015
able to be changed at any time in a manner that does not drop any
legitimate tunneled packets - i.e. the receiver must be willing to
accept both "old" and "new" cookie values during a change of cookie
value. Cookie values SHOULD be changed periodically.
Note that this requirement constrains interoperability with existing
RFC3931 implementations to those supporting a 64-bit cookie.
4. Encapsulation
The ingress router encapsulates the entire Ethernet frame, without
the preamble and frame check sequence (FCS) in L2TPv3 as per RFC4719
[RFC4719]. The L2TPv3 packet is encapsulated directly over IPv6
(i.e. no UDP header is carried).
Any service-delimiting VLAN tag (or in the multi-stack access case
the S-tag and C-tag) SHOULD be removed before the packet is
encapsulated.
The full encapsulation is as follows:
Konstantynowicz, et al. Expires August 22, 2015 [Page 4]
Internet-Draft February 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ver | Traffic Class | Flow Label |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Payload Length | Next Header | Hop Limit |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source address (0:31) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source address (32:63) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source address (64:95) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source address (96:127) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination address (0:31) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination address (32:63) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination address (64:95) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination address (96:127) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Session ID (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cookie (0:31) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cookie (32:63) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Payload (variable) |
| ? |
| ? |
| ? |
| ? |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The combined IPv6 and L2TPv3 header contains the following fields:
o Ver. Set to 0x6 to indicate IPv6.
o Traffic Class. May be set by the ingress router to ensure correct
PHB treatment by transit routers between the ingress and egress,
and correct QoS disposition at the egress router.
o Flow Label. May be set by the ingress router to indicate a flow
of packets from the client which may not be reordered by the
Konstantynowicz, et al. Expires August 22, 2015 [Page 5]
Internet-Draft February 2015
network (if there is a requirement for finer grained ECMP load
balancing than per-circuit load balancing).
o Payload Length. Set to the length of the packet, excluding the
IPv6 header (i.e. the length from the Session ID to the end of the
packet).
o Next Header. Set to 0x73 to indicate that the next header is
L2TPv3.
o Hop Limit. Decremented by one by each router in the path to the
egress router. A hop limit of 0x40 is recommended.
o Source Address. IPv6 source address for the tunnel. In the
"Static 1:1" case the IPv6 source address may correspond to a port
or VLAN being transported as an L2 circuit, or may be a loopback
address terminating inside the router (e.g. if L2 circuits are
being used within a multipoint VPN), or may be an anycast address
terminating on a data center virtual machine.
o Destination Address. IPv6 destination address for the tunnel. As
with the source address this may correspond to a port or VLAN
being transported as an L2 circuit or may be a loopback or anycast
address.
o Session ID. In the "Static 1:1 mapping" case described in
Section 2, the IPv6 address resolves to an L2TPv3 session
immediately, thus the Session ID may be ignored upon receipt. For
compatibility with other tunnel termination platforms supporting
only two-stage resolution (IPv6 Address + Session ID), this
specification recommends supporting explicit configuration of
Session ID to any value other than zero. For cases where both
tunnel endpoints support one-stage resolution (IPv6 Address only),
this specification recommends setting the Session ID to all ones
for easy identification in case of troubleshooting. The Session
ID of zero MUST NOT be used, as it is reserved for use by L2TP
control messages as specified in RFC3931.
o Cookie. 64 bits, configured and described as in Section 3. All
packets for a destined L2 Circuit (or L2TPv3 Session) MUST match
the configured Cookie value. Any packets that do not contain the
required cookie value MUST be discarded (see RFC3931 for more
details).
o Payload. The customer data, with VLAN tag or S-tag/C-tag removed.
As noted above preamble and FCS are stripped before encapsulation.
Since a new FCS is added at each hop when the IP packet is
transmitted the payload is protected against bit errors.
Konstantynowicz, et al. Expires August 22, 2015 [Page 6]
Internet-Draft February 2015
5. Fragmentation and Reassembly
Using tunnel encapsulation, Ethernet L2 datagrams in IPv6 in this
case, will reduce the effective MTU of the Ethernet L2 datagram.
The recommended solution to deal with this problem is for the network
operator to increase the MTU size of all the links between the
devices acting as IPv6 L2TPv3 tunnel endpoints to accommodate both
the IPv6 L2TPv3 encapsulation header and the Ethernet L2 datagram
without fragmenting the IPv6 packet.
6. OAM Considerations
OAM is an important consideration when providing circuit-oriented
services such as those described in this document, and all the more
so in the absence of a dedicated tunnel control plane, as OAM becomes
the only way to detect failures in the tunnel overlay.
Note that in the context of keyed IP tunnels, failures in the IPv6
underlay network can be detected using the usual methods such as
through the routing protocol.
Since keyed IP tunnels always carry an Ethernet payload, and since
OAM at the tunnel layer is unable to detect failures in the Ethernet
service processing at the ingress or egress router, or on the
Ethernet attachment circuit between the router and the Ethernet
client, this document recommends that Ethernet OAM as defined in IEEE
802.1ag [IEEE802.1ag] and/or ITU Y.1731 [Y.1731] is enabled for keyed
IP tunnels. More specifically the following Connecitivity Fault
Management ( CFM ) and/or Ethernet continuity check ( ETH-CC )
configurations are to be used in conjunction with keyed IPv6 tunnels:
o Connectivity verification between the tunnel endpoints across the
tunnel - use an Up MEP located at the tunnel endpoint for
transmitting the CFM PDUs towards, and receiving them from the
direction of the tunnel.
o Connectivity verification from the tunnel endpoint across the
local attachment circuit - use a Down MEP located at the tunnel
endpoint for transmitting the CFM PDUs towards, and receiving them
from the direction of the local attachment circuit.
o Intermediate connectivity verifcation - use a MIP located at the
tunnel endpoint to generate CFM PDUs in response to received CFM
PDUs.
In addition the Pseudowire Virtual Circuit Connectivity Verfication (
VCCV ) RFC5085 [RFC5085] MAY be used.
Konstantynowicz, et al. Expires August 22, 2015 [Page 7]
Internet-Draft February 2015
7. IANA Considerations
None.
8. Security Considerations
Packet spoofing for any type of Virtual Private Network (VPN)
tunneling protocol is of particular concern as insertion of carefully
constructed rogue packets into the VPN transit network could result
in a violation of VPN traffic separation, leaking data into a
customer VPN. This is complicated by the fact that it may be
particularly difficult for the operator of the VPN to even be aware
that it has become a point of transit into or between customer VPNs.
Keyed IPv6 encapsulation provides traffic separation for its VPNs via
use of separate 128-bit IPv6 addresses to identify the endpoints.
The mandatory use of the 64 bit L2TPv3 cookie provides an additional
check to ensure that an arriving packet is intended for the
identified tunnel.
In the presence of a blind packet spoofing attack, the 64 bit L2TPv3
cookie provides security against inadvertent leaking of frames into a
customer VPN, as documented in section 8.2 of RFC3931.
For protection against brute-force, blind, insertion attacks, a 64-
bit Cookie MUST be used with all tunnels.
Note that the Cookie provides no protection against a sophisticated
man-in-the-middle attacker who can sniff and correlate captured data
between nodes for use in a coordinated attack.
The L2TPv3 64-bit cookie must not be regarded as a substitute for
security such as that provided by IPsec when operating over an open
or untrusted network where packets may be sniffed, decoded, and
correlated for use in a coordinated attack.
9. Contributing Authors
Peter Weinberger
Cisco Systems
Email: peweinbe@cisco.com
Michael Lipman
Cisco Systems
Email: mlipman@cisco.com
Konstantynowicz, et al. Expires August 22, 2015 [Page 8]
Internet-Draft February 2015
Mark Townsley
Cisco Systems
Email: townsley@cisco.com
10. Acknowledgements
The authors would like to thank Carlos Pignataro for his suggestions
and review.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3931] Lau, J., Townsley, M., and I. Goyret, "Layer Two Tunneling
Protocol - Version 3 (L2TPv3)", RFC 3931, March 2005.
[RFC4719] Aggarwal, R., Townsley, M., and M. Dos Santos, "Transport
of Ethernet Frames over Layer 2 Tunneling Protocol Version
3 (L2TPv3)", RFC 4719, November 2006.
[RFC5085] Nadeau, T. and C. Pignataro, "Pseudowire Virtual Circuit
Connectivity Verification (VCCV): A Control Channel for
Pseudowires", RFC 5085, December 2007.
11.2. Informative References
[I.D.ietf-pppext-l2tphc]
Valencia, A., "L2TP Header Compression", December 1997.
[IEEE802.1Q]
IEEE, "802.1Q-2014 - IEEE Standard for Local and
metropolitan area networks - Bridges and Bridged
Networks", 2014.
[IEEE802.1ad]
IEEE, "802.1ad-2005 - IEEE Standard for Local and
Metropolitan Area Networks - Virtual Bridged Local Area
Networks - Amendment 4: Provider Bridges", 2005.
[IEEE802.1ag]
IEEE, "IEEE Standard for Local and metropolitan area
networks - Virtual Bridged Local Area Networks, Amendment
5: Connectivity Fault Managements", 2007.
Konstantynowicz, et al. Expires August 22, 2015 [Page 9]
Internet-Draft February 2015
[Y.1731] ITU, "ITU-T Recommendation G.8013/Y.1731 - OAM functions
and mechanisms for Ethernet based networks", 2011.
Authors' Addresses
Maciek Konstantynowicz (editor)
Cisco Systems
Email: maciek@cisco.com
Giles Heron (editor)
Cisco Systems
Email: giheron@cisco.com
Rainer Schatzmayr
Deutsche Telekom AG
Email: rainer.schatzmayr@telekom.de
Wim Henderickx
Alcatel-Lucent, Inc.
Email: wim.henderickx@alcatel-lucent.com
Konstantynowicz, et al. Expires August 22, 2015 [Page 10]
