Internet Draft Document Marc Lasserre
L2VPN Working Group Vach Kompella
draft-ietf-l2vpn-vpls-ldp-09.txt (Editors)
Expires: Dec 2006 June 2006
Virtual Private LAN Services Using LDP
Status of this Memo
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
IPR Disclosure Acknowledgement
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Abstract
This document describes a Virtual Private LAN Service (VPLS)
solution using pseudo-wires, a service previously implemented over
other tunneling technologies and known as Transparent LAN Services
(TLS). A VPLS creates an emulated LAN segment for a given set of
users, i.e., it creates a Layer 2 broadcast domain that is fully
capable of learning and forwarding on Ethernet MAC addresses that
is closed to a given set of users. Multiple VPLS services can be
supported from a single PE node.
This document describes the control plane functions of signaling
pseudo-wire labels using LDP [RFC3036], extending [RFC4447]. It is
agnostic to discovery protocols. The data plane functions of
forwarding are also described, focusing, in particular, on the
Lasserre, Kompella [Page 1]
Internet Draft Virtual Private LAN Service over LDP June 2006
learning of MAC addresses. The encapsulation of VPLS packets is
described by [RFC4448].
1. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in RFC 2119
[RFC2119].
2. Table of Contents
1. Conventions.....................................................2
2. Table of Contents...............................................2
3. Introduction....................................................3
3.1. Terminology...................................................3
3.2. Acronyms......................................................4
4. Topological Model for VPLS......................................5
4.1. Flooding and Forwarding.......................................5
4.2. Address Learning..............................................6
4.3. Tunnel Topology...............................................6
4.4. Loop free VPLS................................................6
5. Discovery.......................................................7
6. Control Plane...................................................7
6.1. LDP Based Signaling of Demultiplexers.........................7
6.1.1. Using the Generalized PWid FEC Element......................8
6.2. MAC Address Withdrawal........................................8
6.2.1. MAC List TLV................................................9
6.2.2. Address Withdraw Message Containing MAC List TLV...........10
7. Data Forwarding on an Ethernet PW..............................10
7.1. VPLS Encapsulation actions...................................10
7.2. VPLS Learning actions........................................11
8. Data Forwarding on an Ethernet VLAN PW.........................12
8.1. VPLS Encapsulation actions...................................12
9. Operation of a VPLS............................................13
9.1. MAC Address Aging............................................14
10. A Hierarchical VPLS Model.....................................14
10.1. Hierarchical connectivity...................................15
10.1.1. Spoke connectivity for bridging-capable devices...........15
10.1.2. Advantages of spoke connectivity..........................17
10.1.3. Spoke connectivity for non-bridging devices...............17
10.2. Redundant Spoke Connections.................................19
10.2.1. Dual-homed MTU-s..........................................19
10.2.2. Failure detection and recovery............................20
10.3. Multi-domain VPLS service...................................21
11. Hierarchical VPLS model using Ethernet Access Network.........21
11.1. Scalability.................................................22
11.2. Dual Homing and Failure Recovery............................22
Lasserre, et al. [Page 2]
Internet Draft Virtual Private LAN Service over LDP June 2006
12. Contributors..................................................22
13. Acknowledgments...............................................23
14. Security Considerations.......................................23
15. IANA Considerations...........................................24
16. References....................................................24
16.1. Normative References........................................24
16.2. Informative References......................................25
17. Appendix: VPLS Signaling using the PWid FEC Element...........25
18. Authors' Addresses............................................26
3. Introduction
Ethernet has become the predominant technology for Local Area
Network (LAN) connectivity and is gaining acceptance as an access
technology, specifically in Metropolitan and Wide Area Networks
(MAN and WAN, respectively). The primary motivation behind Virtual
Private LAN Services (VPLS) is to provide connectivity between
geographically dispersed customer sites across MANs and WANs, as if
they were connected using a LAN. The intended application for the
end-user can be divided into the following two categories:
- Connectivity between customer routers: LAN routing application
- Connectivity between customer Ethernet switches: LAN switching
application
Broadcast and multicast services are available over traditional
LANs. Sites that belong to the same broadcast domain and that are
connected via an MPLS network expect broadcast, multicast and
unicast traffic to be forwarded to the proper location(s). This
requires MAC address learning/aging on a per pseudo-wire basis,
packet replication across pseudo-wires for multicast/broadcast
traffic and for flooding of unknown unicast destination traffic.
[RFC4448] defines how to carry Layer 2 (L2) frames over point-to-
point pseudo-wires (PW). This document describes extensions to
[RFC4447] for transporting Ethernet/802.3 and VLAN [802.1Q] traffic
across multiple sites that belong to the same L2 broadcast domain
or VPLS. Note that the same model can be applied to other 802.1
technologies. It describes a simple and scalable way to offer
Virtual LAN services, including the appropriate flooding of
broadcast, multicast and unknown unicast destination traffic over
MPLS, without the need for address resolution servers or other
external servers, as discussed in [L2VPN-REQ].
The following discussion applies to devices that are VPLS capable
and have a means of tunneling labeled packets amongst each other.
The resulting set of interconnected devices forms a private MPLS
VPN.
3.1. Terminology
Lasserre, et al. [Page 3]
Internet Draft Virtual Private LAN Service over LDP June 2006
Q-in-Q 802.1ad Provider Bridge extensions also known
as stackable VLANs or Q-in-Q.
Qualified learning Learning mode in which each customer VLAN is
mapped to its own VPLS instance.
Service delimitor Information used to identify a specific customer
service instance. This is typically encoded in
the encapsulation header of customer frames
(e.g. VLAN Id).
Tagged frame Frame with an 802.1Q VLAN identifier.
Unqualified learning Learning mode where all the VLANs of a single
customer are mapped to a single VPLS.
Untagged frame Frame without an 802.1Q VLAN identifier
3.2. Acronyms
AC Attachment Circuit
BPDU Bridge Protocol Data Unit
CE Customer Edge device
FEC Forwarding Equivalence Class
FIB Forwarding Information Base
GRE Generic Routing Encapsulation
IPsec IP secutity
L2TP Layer Two Tunneling Protocol
LAN Local Area Network
LDP Label Distribution Protocol
MTU-s Multi-Tenant Unit switch
PE Provider Edge device
PW Pseudo-wire
STP Spanning Tree Protocol
VLAN Virtual LAN
VLAN tag VLAN Identifier
Lasserre, et al. [Page 4]
Internet Draft Virtual Private LAN Service over LDP June 2006
4. Topological Model for VPLS
An interface participating in a VPLS must be able to flood,
forward, and filter Ethernet frames. Figure 1 below shows the
topological model of a VPLS. The set of PE devices interconnected
via PWs appears as a single emulated LAN to customer X. Each PE
will form remote MAC address to PW associations and associate
directly attached MAC addresses to local customer facing ports.
This is modeled on standard IEEE 802.1 MAC address learning.
+-----+ +-----+
| CE1 +---+ ........................... +---| CE2 |
+-----+ | . . | +-----+
Site 1 | +----+ +----+ | Site 2
+---| PE | Cloud | PE |---+
+----+ +----+
. .
. +----+ .
..........| PE |...........
+----+ ^
| |
| +-- Emulated LAN
+-----+
| CE3 |
+-----+
Site 3
Figure 1: Topological Model of a VPLS for Customer X
With three sites
We note here again that while this document shows specific examples
using MPLS transport tunnels, other tunnels that can be used by PWs
(as mentioned in [RFC4447]), e.g., GRE, L2TP, IPsec, etc., can also
be used, as long as the originating PE can be identified, since
this is used in the MAC learning process.
The scope of the VPLS lies within the PEs in the service provider
network, highlighting the fact that apart from customer service
delineation, the form of access to a customer site is not relevant
to the VPLS [L2VPN-REQ]. In other words, the attachment circuit
(AC) connected to the customer could be a physical Ethernet port, a
logical (tagged) Ethernet port, an ATM PVC carrying Ethernet
frames, etc., or even an Ethernet PW.
The PE is typically an edge router capable of running the LDP
signaling protocol and/or routing protocols to set up PWs. In
addition, it is capable of setting up transport tunnels to other
PEs and delivering traffic over PWs.
4.1. Flooding and Forwarding
Lasserre, et al. [Page 5]
Internet Draft Virtual Private LAN Service over LDP June 2006
One of attributes of an Ethernet service is that frames sent to
broadcast addresses and to unknown destination MAC addresses are
flooded to all ports. To achieve flooding within the service
provider network, all unknown unicast, broadcast and multicast
frames are flooded over the corresponding PWs to all PE nodes
participating in the VPLS, as well as to all ACs.
Note that multicast frames are a special case and do not
necessarily have to be sent to all VPN members. For simplicity,
the default approach of broadcasting multicast frames is used.
To forward a frame, a PE MUST be able to associate a destination
MAC address with a PW. It is unreasonable and perhaps impossible
to require PEs to statically configure an association of every
possible destination MAC address with a PW. Therefore, VPLS-
capable PEs SHOULD have the capability to dynamically learn MAC
addresses on both ACs and PWs and to forward and replicate packets
across both ACs and PWs.
4.2. Address Learning
Unlike BGP VPNs [BGP-VPN], reachability information is not
advertised and distributed via a control plane. Reachability is
obtained by standard learning bridge functions in the data plane.
When a packet arrives on a PW, if the source MAC address is
unknown, it needs to be associated with the PW, so that outbound
packets to that MAC address can be delivered over the associated
PW. Likewise, when a packet arrives on an AC, if the source MAC
address is unknown, it needs to be associated with the AC, so that
outbound packets to that MAC address can be delivered over the
associated AC.
Standard learning, filtering and forwarding actions, as defined in
[802.1D-ORIG], [802.1D-REV] and [802.1Q], are required when a PW or
AC state changes.
4.3. Tunnel Topology
PE routers are assumed to have the capability to establish
transport tunnels. Tunnels are set up between PEs to aggregate
traffic. PWs are signaled to demultiplex encapsulated Ethernet
frames from multiple VPLS instances that traverse the transport
tunnels.
In an Ethernet L2VPN, it becomes the responsibility of the service
provider to create the loop free topology. For the sake of
simplicity, we define that the topology of a VPLS is a full mesh of
PWs.
4.4. Loop free VPLS
Lasserre, et al. [Page 6]
Internet Draft Virtual Private LAN Service over LDP June 2006
If the topology of the VPLS is not restricted to a full mesh, then
it may be that for two PEs not directly connected via PWs, they
would have to use an intermediary PE to relay packets. This
topology would require the use of some loop-breaking protocol, like
a spanning tree protocol.
Instead, a full mesh of PWs is established between PEs. Since
every PE is now directly connected to every other PE in the VPLS
via a PW, there is no longer any need to relay packets, and we can
instantiate a simpler loop-breaking rule - the "split horizon"
rule: a PE MUST NOT forward traffic from one PW to another in the
same VPLS mesh.
Note that customers are allowed to run a Spanning Tree Protocol
(STP) (e.g., as defined in [802.1D-REV]), such as when a customer
has "back door" links used to provide redundancy in the case of a
failure within the VPLS. In such a case, STP Bridge PDUs (BPDUs)
are simply tunneled through the provider cloud.
5. Discovery
The capability to manually configure the addresses of the remote
PEs is REQUIRED. However, the use of manual configuration is not
necessary if an auto-discovery procedure is used. A number of
auto-discovery procedures are compatible with this document
([RADIUS-DISC], [BGP-DISC]).
6. Control Plane
This document describes the control plane functions of signaling of
PW labels. Some foundational work in the area of support for
multi-homing is laid. The extensions to provide multi-homing
support should work independently of the basic VPLS operation, and
are not described here.
6.1. LDP Based Signaling of Demultiplexers
A full mesh of LDP sessions is used to establish the mesh of PWs.
The requirement for a full mesh of PWs may result in a large number
of targeted LDP sessions. Section 8 discusses the option of
setting up hierarchical topologies in order to minimize the size of
the VPLS full mesh.
Once an LDP session has been formed between two PEs, all PWs
between these two PEs are signaled over this session.
In [RFC4447], two types of FECs are described, the PWid FEC Element
(FEC type 128) and the Generalized PWid FEC Element (FEC type 129).
The original FEC element used for VPLS was compatible with the PWid
FEC Element. The text for signaling using PWid FEC Element has
been moved to Appendix 1. What we describe below replaces that
with a more generalized L2VPN descriptor, the Generalized PWid FEC
Element.
Lasserre, et al. [Page 7]
Internet Draft Virtual Private LAN Service over LDP June 2006
6.1.1. Using the Generalized PWid FEC Element
[RFC4447] describes a generalized FEC structure that is be used for
VPLS signaling in the following manner. We describe the assignment
of the Generalized PWid FEC Element fields in the context of VPLS
signaling.
Control bit (C): This bit is used to signal the use of the control
word as specified in [RFC4447].
PW type: The allowed PW types are Ethernet (0x0005) and Ethernet
tagged mode (0x004) as specified in [IANA].
PW info length: As specified in [RFC4447].
Attachment Group Identifier (AGI), Length, Value: The unique name
of this VPLS. The AGI identifies a type of name, Length denotes
the length of Value, which is the name of the VPLS. We use the
term AGI interchangeably with VPLS identifier.
Target Attachment Individual Identifier (TAII), Source Attachment
Individual Identifier (SAII): These are null because the mesh of
PWs in a VPLS terminate on MAC learning tables, rather than on
individual attachment circuits. The use of non-null TAII and SAII
is reserved for future enhancements.
Interface Parameters: The relevant interface parameters are:
- MTU: the MTU (Maximum Transmission Unit) of the VPLS MUST be
the same across all the PWs in the mesh.
- Optional Description String: same as [RFC4447].
- Requested VLAN ID: If the PW type is Ethernet tagged mode,
this parameter may be used to signal the insertion of the
appropriate VLAN ID, as defined in [RFC4448].
6.2. MAC Address Withdrawal
It MAY be desirable to remove or unlearn MAC addresses that have
been dynamically learned for faster convergence. This is
accomplished by sending an LDP Address Withdraw Message with the
list of MAC addresses to be removed to all other PEs over the
corresponding LDP sessions.
We introduce an optional MAC List TLV in LDP to specify a list of
MAC addresses that can be removed or unlearned using the LDP
Address Withdraw Message.
The Address Withdraw message with MAC List TLVs MAY be supported in
order to expedite removal of MAC addresses as the result of a
Lasserre, et al. [Page 8]
Internet Draft Virtual Private LAN Service over LDP June 2006
topology change (e.g., failure of the primary link for a dual-homed
VPLS-capable switch).
In order to minimize the impact on LDP convergence time, when the
MAC list TLV contains a large number of MAC addresses, it may be
preferable to send a MAC address withdrawal message with an empty
list.
6.2.1. MAC List TLV
MAC addresses to be unlearned can be signaled using an LDP Address
Withdraw Message that contains a new TLV, the MAC List TLV. Its
format is described below. The encoding of a MAC List TLV address
is the 6-octet MAC address specified by IEEE 802 documents [g-ORIG]
[802.1D-REV].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|U|F| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAC address #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAC address #1 | MAC Address #2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAC address #2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAC address #n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAC address #n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
U bit: Unknown bit. This bit MUST be set to 1. If the MAC address
format is not understood, then the TLV is not understood, and MUST
be ignored.
F bit: Forward bit. This bit MUST be set to 0. Since the LDP
mechanism used here is targeted, the TLV MUST NOT be forwarded.
Type: Type field. This field MUST be set to 0x0404 (subject to
IANA approval). This identifies the TLV type as MAC List TLV.
Length: Length field. This field specifies the total length in
octets of the MAC addresses in the TLV. The length MUST be a
multiple of 6.
MAC Address: The MAC address(es) being removed.
The MAC Address Withdraw Message contains a FEC TLV (to identify
the VPLS affected), a MAC Address TLV and optional parameters. No
optional parameters have been defined for the MAC Address Withdraw
Lasserre, et al. [Page 9]
Internet Draft Virtual Private LAN Service over LDP June 2006
signaling. Note that if a PE receives a MAC Address Withdraw
Message and does not understand it, it MUST ignore the message. In
this case, instead of flushing its MAC address table, it will
continue to use stale information, unless:
- it receives a packet with a known MAC address association,
but from a different PW, in which case it replaces the old
association, or
- it ages out the old association
The MAC Address Withdraw message only helps to speed up
convergence, so PEs that do not understand the message can continue
to participate in the VPLS.
6.2.2. Address Withdraw Message Containing MAC List TLV
The processing for MAC List TLV received in an Address Withdraw
Message is:
For each MAC address in the TLV:
- Remove the association between the MAC address and the AC or
PW over which this message is received
For a MAC Address Withdraw message with empty list:
- Remove all the MAC addresses associated with the VPLS
instance (specified by the FEC TLV) except the MAC addresses
learned over the PW associated with this signaling session
over which the message was received
The scope of a MAC List TLV is the VPLS specified in the FEC TLV in
the MAC Address Withdraw Message. The number of MAC addresses can
be deduced from the length field in the TLV.
7. Data Forwarding on an Ethernet PW
This section describes the data plane behavior on an Ethernet
PW used in a VPLS. While the encapsulation is similar to that
described in [RFC4448], the functions of stripping the service-
delimiting tag and using a "normalized" Ethernet frame are
described.
7.1. VPLS Encapsulation actions
In a VPLS, a customer Ethernet frame without preamble is
encapsulated with a header as defined in [RFC4448]. A customer
Ethernet frame is defined as follows:
- If the frame, as it arrives at the PE, has an encapsulation
that is used by the local PE as a service delimiter, i.e., to
identify the customer and/or the particular service of that
customer, then that encapsulation may be stripped before the
Lasserre, et al. [Page 10]
Internet Draft Virtual Private LAN Service over LDP June 2006
frame is sent into the VPLS. As the frame exits the VPLS,
the frame may have a service-delimiting encapsulation
inserted.
- If the frame, as it arrives at the PE, has an encapsulation
that is not service delimiting, then it is a customer frame
whose encapsulation should not be modified by the VPLS. This
covers, for example, a frame that carries customer-specific
VLAN tags that the service provider neither knows about nor
wants to modify.
As an application of these rules, a customer frame may arrive at a
customer-facing port with a VLAN tag that identifies the customer's
VPLS instance. That tag would be stripped before it is
encapsulated in the VPLS. At egress, the frame may be tagged
again, if a service-delimiting tag is used, or it may be untagged
if none is used.
Likewise, if a customer frame arrives at a customer-facing port
over an ATM or Frame Relay VC that identifies the customer's VPLS
instance, then the ATM or FR encapsulation is removed before the
frame is passed into the VPLS.
Contrariwise, if a customer frame arrives at a customer-facing port
with a VLAN tag that identifies a VLAN domain in the customer L2
network, then the tag is not modified or stripped, as it belongs
with the rest of the customer frame.
By following the above rules, the Ethernet frame that traverses a
VPLS is always a customer Ethernet frame. Note that the two
actions, at ingress and egress, of dealing with service delimiters
are local actions that neither PE has to signal to the other. They
allow, for example, a mix-and-match of VLAN tagged and untagged
services at either end, and do not carry across a VPLS a VLAN tag
that has local significance only. The service delimiter may be an
MPLS label also, whereby an Ethernet PW given by [RFC4448] can
serve as the access side connection into a PE. An RFC1483 Bridged
PVC encapsulation could also serve as a service delimiter. By
limiting the scope of locally significant encapsulations to the
edge, hierarchical VPLS models can be developed that provide the
capability to network-engineer scalable VPLS deployments, as
described below.
7.2. VPLS Learning actions
Learning is done based on the customer Ethernet frame as defined
above. The Forwarding Information Base (FIB) keeps track of the
mapping of customer Ethernet frame addressing and the appropriate
PW to use. We define two modes of learning: qualified and
unqualified learning. Qualified learning is the default mode and
MUST be supported. Support of unqualified learning is OPTIONAL.
Lasserre, et al. [Page 11]
Internet Draft Virtual Private LAN Service over LDP June 2006
In unqualified learning, all the VLANs of a single customer are
handled by a single VPLS, which means they all share a single
broadcast domain and a single MAC address space. This means that
MAC addresses need to be unique and non-overlapping among customer
VLANs or else they cannot be differentiated within the VPLS
instance and this can result in loss of customer frames. An
application of unqualified learning is port-based VPLS service for
a given customer (e.g., customer with non-multiplexed AC where all
the traffic on a physical port, which may include multiple customer
VLANs, is mapped to a single VPLS instance).
In qualified learning, each customer VLAN is assigned to its own
VPLS instance, which means each customer VLAN has its own broadcast
domain and MAC address space. Therefore, in qualified learning,
MAC addresses among customer VLANs may overlap with each other, but
they will be handled correctly since each customer VLAN has its own
FIB, i.e., each customer VLAN has its own MAC address space. Since
VPLS broadcasts multicast frames by default, qualified learning
offers the advantage of limiting the broadcast scope to a given
customer VLAN. Qualified learning can result in large FIB table
sizes, because the logical MAC address is now a VLAN tag + MAC
address.
For STP to work in qualified learning mode, a VPLS PE must be able
to forward STP BPDUs over the proper VPLS instance. In a
hierarchical VPLS case (see details in Section 10), service
delimiting tags (Q-in-Q or [RFC4448]) can be added such that PEs
can unambiguously identify all customer traffic, including STP
BPDUs. In a basic VPLS case, upstream switches must insert such
service delimiting tags. When an access port is shared among
multiple customers, a reserved VLAN per customer domain must be
used to carry STP traffic. The STP frames are encapsulated with a
unique provider tag per customer (as the regular customer traffic),
and a PEs looks up the provider tag to send such frames across the
proper VPLS instance.
8. Data Forwarding on an Ethernet VLAN PW
This section describes the data plane behavior on an Ethernet VLAN
PW in a VPLS. While the encapsulation is similar to that described
in [RFC4448], the functions of imposing tags and using a
"normalized" Ethernet frame are described. The learning behavior
is the same as for Ethernet PWs.
8.1. VPLS Encapsulation actions
In a VPLS, a customer Ethernet frame without preamble is
encapsulated with a header as defined in [RFC4448]. A customer
Ethernet frame is defined as follows:
Lasserre, et al. [Page 12]
Internet Draft Virtual Private LAN Service over LDP June 2006
- If the frame, as it arrives at the PE, has an encapsulation
that is part of the customer frame, and is also used by the
local PE as a service delimiter, i.e., to identify the
customer and/or the particular service of that customer, then
that encapsulation is preserved as the frame is sent into the
VPLS, unless the Requested VLAN ID optional parameter was
signaled. In that case, the VLAN tag is overwritten before
the frame is sent out on the PW.
- If the frame, as it arrives at the PE, has an encapsulation
that does not have the required VLAN tag, a null tag is
imposed if the Requested VLAN ID optional parameter was not
signaled.
As an application of these rules, a customer frame may arrive at a
customer-facing port with a VLAN tag that identifies the customer's
VPLS instance and also identifies a customer VLAN. That tag would
be preserved as it is encapsulated in the VPLS.
The Ethernet VLAN PW provides a simple way to preserve customer
802.1p bits.
A VPLS MAY have both Ethernet and Ethernet VLAN PWs. However, if a
PE is not able to support both PWs simultaneously, it SHOULD send a
Label Release on the PW messages that it cannot support with a
status code "Unknown FEC" as given in [RFC3036].
9. Operation of a VPLS
We show here, in Figure 2 below, an example of how a VPLS works.
The following discussion uses the figure below, where a VPLS has
been set up between PE1, PE2 and PE3. The VPLS connects a customer
with 4 sites labeled A1, A2, A3 and A4 through CE1, CE2, CE3 and
CE4, respectively.
Initially, the VPLS is set up so that PE1, PE2 and PE3 have a full
mesh of Ethernet PWs. The VPLS instance is assigned an identifier
(AGI). For the above example, say PE1 signals PW label 102 to PE2
and 103 to PE3, and PE2 signals PW label 201 to PE1 and 203 to PE3.
Lasserre, et al. [Page 13]
Internet Draft Virtual Private LAN Service over LDP June 2006
-----
/ A1 \
---- ----CE1 |
/ \ -------- ------- / | |
| A2 CE2- / \ / PE1 \ /
\ / \ / \---/ \ -----
---- ---PE2 |
| Service Provider Network |
\ / \ /
----- PE3 / \ /
|Agg|_/ -------- -------
-| |
---- / ----- ----
/ \/ \ / \ CE = Customer Edge Router
| A3 CE3 -CE4 A4 | PE = Provider Edge Router
\ / \ / Agg = Layer 2 Aggregation
---- ----
Figure 2: Example of a VPLS
Assume a packet from A1 is bound for A2. When it leaves CE1, say
it has a source MAC address of M1 and a destination MAC of M2. If
PE1 does not know where M2 is, it will flood the packet, i.e., send
it to PE2 and PE3. When PE2 receives the packet, it will have a PW
label of 201. PE2 can conclude that the source MAC address M1 is
behind PE1, since it distributed the label 201 to PE1. It can
therefore associate MAC address M1 with PW label 102.
9.1. MAC Address Aging
PEs that learn remote MAC addresses SHOULD have an aging mechanism
to remove unused entries associated with a PW label. This is
important both for conservation of memory as well as for
administrative purposes. For example, if a customer site A is shut
down, eventually, the other PEs should unlearn A's MAC address.
The aging timer for MAC address M SHOULD be reset when a packet
with source MAC address M is received.
10. A Hierarchical VPLS Model
The solution described above requires a full mesh of tunnel LSPs
between all the PE routers that participate in the VPLS service.
For each VPLS service, n*(n-1)/2 PWs must be setup between the PE
routers. While this creates signaling overhead, the real detriment
to large scale deployment is the packet replication requirements
for each provisioned PWs on a PE router. Hierarchical
connectivity, described in this document reduces signaling and
replication overhead to allow large scale deployment.
In many cases, service providers place smaller edge devices in
multi-tenant buildings and aggregate them into a PE in a large
Central Office (CO) facility. In some instances, standard IEEE
Lasserre, et al. [Page 14]
Internet Draft Virtual Private LAN Service over LDP June 2006
802.1q (Dot 1Q) tagging techniques may be used to facilitate
mapping CE interfaces to VPLS access circuits at a PE.
It is often beneficial to extend the VPLS service tunneling
techniques into the access switch domain. This can be accomplished
by treating the access device as a PE and provisioning PWs between
it and every other edge, as a basic VPLS. An alternative is to
utilize [RFC4448] PWs or Q-in-Q logical interfaces between the
access device and selected VPLS enabled PE routers. Q-in-Q
encapsulation is another form of L2 tunneling technique, which can
be used in conjunction with MPLS signaling as will be described
later. The following two sections focus on this alternative
approach. The VPLS core PWs (hub) are augmented with access PWs
(spoke) to form a two-tier hierarchical VPLS (H-VPLS).
Spoke PWs may be implemented using any L2 tunneling mechanism,
expanding the scope of the first tier to include non-bridging VPLS
PE routers. The non-bridging PE router would extend a spoke PW
from a Layer-2 switch that connects to it, through the service core
network, to a bridging VPLS PE router supporting hub PWs. We also
describe how VPLS-challenged nodes and low-end CEs without MPLS
capabilities may participate in a hierarchical VPLS.
For rest of this discussion we refer to a bridging capable access
device as MTU-s and a non-bridging capable PE as PE-r. We refer to
a routing and bridging capable device as PE-rs.
10.1. Hierarchical connectivity
This section describes the hub and spoke connectivity model and
describes the requirements of the bridging capable and non-bridging
MTU-s devices for supporting the spoke connections.
10.1.1. Spoke connectivity for bridging-capable devices
In Figure 3 below, three customer sites are connected to an MTU-s
through CE-1, CE-2, and CE-3. The MTU-s has a single connection
(PW-1) to PE1-rs. The PE-rs devices are connected in a basic VPLS
full mesh. For each VPLS service, a single spoke PW is set up
between the MTU-s and the PE-rs based on [RFC4447]. Unlike
traditional PWs that terminate on a physical (or a VLAN-tagged
logical) port, a spoke PW terminates on a virtual switch instance
(VSI, see [L2FRAME]) on the MTU-s and the PE-rs devices.
Lasserre, et al. [Page 15]
Internet Draft Virtual Private LAN Service over LDP June 2006
PE2-rs
+--------+
| |
| -- |
| / \ |
CE-1 | \S / |
\ | -- |
\ +--------+
\ MTU-s PE1-rs / |
+--------+ +--------+ / |
| | | | / |
| -- | PW-1 | -- |---/ |
| / \--|- - - - - - - - - - - | / \ | |
| \S / | | \S / | |
| -- | | -- |---\ |
+--------+ +--------+ \ |
/ \ |
---- +--------+
|Agg | | |
---- | -- |
/ \ | / \ |
CE-2 CE-3 | \S / |
| -- |
+--------+
PE3-rs
Agg = Layer-2 Aggregation
--
/ \
\S / = Virtual Switch Instance
--
Figure 3: An example of a hierarchical VPLS model
The MTU-s and the PE-rs treat each spoke connection like an AC of
the VPLS service. The PW label is used to associate the traffic
from the spoke to a VPLS instance.
10.1.1.1. MTU-s Operation
An MTU-s is defined as a device that supports layer-2 switching
functionality and does all the normal bridging functions of
learning and replication on all its ports, including the spoke,
which is treated as a virtual port. Packets to unknown
destinations are replicated to all ports in the service including
the spoke. Once the MAC address is learned, traffic between CE1
and CE2 will be switched locally by the MTU-s saving the capacity
of the spoke to the PE-rs. Similarly traffic between CE1 or CE2
and any remote destination is switched directly on to the spoke and
sent to the PE-rs over the point-to-point PW.
Since the MTU-s is bridging capable, only a single PW is required
per VPLS instance for any number of access connections in the same
Lasserre, et al. [Page 16]
Internet Draft Virtual Private LAN Service over LDP June 2006
VPLS service. This further reduces the signaling overhead between
the MTU-s and PE-rs.
If the MTU-s is directly connected to the PE-rs, other
encapsulation techniques such as Q-in-Q can be used for the spoke.
10.1.1.2. PE-rs Operation
A PE-rs is a device that supports all the bridging functions for
VPLS service and supports the routing and MPLS encapsulation, i.e.,
it supports all the functions described for a basic VPLS as
described above.
The operation of PE-rs is independent of the type of device at the
other end of the spoke. Thus, the spoke from the MTU-s is treated
as a virtual port and the PE-rs will switch traffic between the
spoke PW, hub PWs, and ACs once it has learned the MAC addresses.
10.1.2. Advantages of spoke connectivity
Spoke connectivity offers several scaling and operational
advantages for creating large scale VPLS implementations, while
retaining the ability to offer all the functionality of the VPLS
service.
- Eliminates the need for a full mesh of tunnels and full mesh
of PWs per service between all devices participating in the
VPLS service.
- Minimizes signaling overhead since fewer PWs are required for
the VPLS service.
- Segments VPLS nodal discovery. MTU-s needs to be aware of
only the PE-rs node although it is participating in the VPLS
service that spans multiple devices. On the other hand,
every VPLS PE-rs must be aware of every other VPLS PE-rs and
all of its locally connected MTU-s and PE-r devices.
- Addition of other sites requires configuration of the new
MTU-s but does not require any provisioning of the existing
MTU-s devices on that service.
- Hierarchical connections can be used to create VPLS service
that spans multiple service provider domains. This is
explained in a later section.
Note that as more devices participate in the VPLS, there are more
devices that require the capability for learning and replication.
10.1.3. Spoke connectivity for non-bridging devices
In some cases, a bridging PE-rs may not be deployed, or a PE-r
might already have been deployed. In this section, we explain how
a PE-r that does not support any of the VPLS bridging functionality
can participate in the VPLS service.
Lasserre, et al. [Page 17]
Internet Draft Virtual Private LAN Service over LDP June 2006
In Figure 4, three customer sites are connected through CE-1, CE-2
and CE-3 to the VPLS through PE-r. For every attachment circuit
that participates in the VPLS service, PE-r creates a point-to-
point PW that terminates on the VSI of PE1-rs.
PE2-rs
+--------+
| |
| -- |
| / \ |
CE-1 | \S / |
\ | -- |
\ +--------+
\ PE-r PE1-rs / |
+--------+ +--------+ / |
|\ | | | / |
| \ | PW-1 | -- |---/ |
| ------|- - - - - - - - - - - | / \ | |
| -----|- - - - - - - - - - - | \S / | |
| / | | -- |---\ |
+--------+ +--------+ \ |
/ \ |
---- +--------+
| Agg| | |
---- | -- |
/ \ | / \ |
CE-2 CE-3 | \S / |
| -- |
+--------+
PE3-rs
Figure 4: An example of a hierarchical VPLS
with non-bridging spokes
The PE-r is defined as a device that supports routing but does not
support any bridging functions. However, it is capable of setting
up PWs between itself and the PE-rs. For every port that is
supported in the VPLS service, a PW is setup from the PE-r to the
PE-rs. Once the PWs are setup, there is no learning or replication
function required on the part of the PE-r. All traffic received on
any of the ACs is transmitted on the PW. Similarly all traffic
received on a PW is transmitted to the AC where the PW terminates.
Thus traffic from CE1 destined for CE2 is switched at PE1-rs and
not at PE-r.
Note that in the case where PE-r devices use Provider VLANs (P-
VLAN) as demultiplexers instead of PWs, PE1-rs can treat them as
such and map these "circuits" into a VPLS domain to provide
bridging support between them.
Lasserre, et al. [Page 18]
Internet Draft Virtual Private LAN Service over LDP June 2006
This approach adds more overhead than the bridging capable (MTU-s)
spoke approach since a PW is required for every AC that
participates in the service versus a single PW required per service
(regardless of ACs) when an MTU-s is used. However, this approach
offers the advantage of offering a VPLS service in conjunction with
a routed internet service without requiring the addition of new
MTU-s.
10.2. Redundant Spoke Connections
An obvious weakness of the hub and spoke approach described thus
far is that the MTU-s has a single connection to the PE-rs. In
case of failure of the connection or the PE-rs, the MTU-s suffers
total loss of connectivity.
In this section we describe how the redundant connections can be
provided to avoid total loss of connectivity from the MTU-s. The
mechanism described is identical for both, MTU-s and PE-r devices.
10.2.1. Dual-homed MTU-s
To protect from connection failure of the PW or the failure of the
PE-rs, the MTU-s or the PE-r is dual-homed into two PE-rs devices.
The PE-rs devices must be part of the same VPLS service instance.
In Figure 5, two customer sites are connected through CE-1 and CE-2
to an MTU-s. The MTU-s sets up two PWs (one each to PE1-rs and PE3-
rs) for each VPLS instance. One of the two PWs is designated as
primary and is the one that is actively used under normal
conditions, while the second PW is designated as secondary and is
held in a standby state. The MTU-s negotiates the PW labels for
both the primary and secondary PWs, but does not use the secondary
PW unless the primary PW fails. How a spoke is designated primary
or secondary is outside of the scope of this document. For
example, a spanning tree instance running between only the MTU-s
and the two PE-rs nodes is one possible method. Another method
could be configuration.
Lasserre, et al. [Page 19]
Internet Draft Virtual Private LAN Service over LDP June 2006
PE2-rs
+--------+
| |
| -- |
| / \ |
CE-1 | \S / |
\ | -- |
\ +--------+
\ MTU-s PE1-rs / |
+--------+ +--------+ / |
| | | | / |
| -- | Primary PW | -- |---/ |
| / \ |- - - - - - - - - - - | / \ | |
| \S / | | \S / | |
| -- | | -- |---\ |
+--------+ +--------+ \ |
/ \ \ |
/ \ +--------+
/ \ | |
CE-2 \ | -- |
\ Secondary PW | / \ |
- - - - - - - - - - - - - - - - - | \S / |
| -- |
+--------+
PE3-rs
Figure 5: An example of a dual-homed MTU-s
10.2.2. Failure detection and recovery
The MTU-s should control the usage of the spokes to the PE-rs
devices. If the spokes are PWs, then LDP signaling is used to
negotiate the PW labels, and the hello messages used for the LDP
session could be used to detect failure of the primary PW. The use
of other mechanisms which could provide faster detection failures
is outside the scope of this document.
Upon failure of the primary PW, MTU-s immediately switches to the
secondary PW. At this point the PE3-rs that terminates the
secondary PW starts learning MAC addresses on the spoke PW. All
other PE-rs nodes in the network think that CE-1 and CE-2 are
behind PE1-rs and may continue to send traffic to PE1-rs until they
learn that the devices are now behind PE3-rs. The unlearning
process can take a long time and may adversely affect the
connectivity of higher level protocols from CE1 and CE2. To enable
faster convergence, the PE3-rs where the secondary PW got activated
may send out a flush message (as explained in section 4.2), using
the MAC List TLV as defined in Section 6, to all PE-rs nodes. Upon
receiving the message, PE-rs nodes flush the MAC addresses
associated with that VPLS instance.
Lasserre, et al. [Page 20]
Internet Draft Virtual Private LAN Service over LDP June 2006
10.3. Multi-domain VPLS service
Hierarchy can also be used to create a large scale VPLS service
within a single domain or a service that spans multiple domains
without requiring full mesh connectivity between all VPLS capable
devices. Two fully meshed VPLS networks are connected together
using a single LSP tunnel between the VPLS "border" devices. A
single spoke PW per VPLS service is set up to connect the two
domains together.
When more than two domains need to be connected, a full mesh of
inter-domain spokes is created between border PEs. Forwarding
rules over this mesh are identical to the rules defined in section
5.
This creates a three-tier hierarchical model that consists of a
hub-and-spoke topology between MTU-s and PE-rs devices, a full-mesh
topology between PE-rs, and a full mesh of inter-domain spokes
between border PE-rs devices.
This document does not specify how redundant border PEs per domain
per VPLS instance can be supported.
11. Hierarchical VPLS model using Ethernet Access Network
In this section the hierarchical model is expanded to include an
Ethernet access network. This model retains the hierarchical
architecture discussed previously in that it leverages the full-
mesh topology among PE-rs devices; however, no restriction is
imposed on the topology of the Ethernet access network (e.g., the
topology between MTU-s and PE-rs devices is not restricted to hub
and spoke).
The motivation for an Ethernet access network is that Ethernet-
based networks are currently deployed by some service providers to
offer VPLS services to their customers. Therefore, it is important
to provide a mechanism that allows these networks to integrate with
an IP or MPLS core to provide scalable VPLS services.
One approach of tunneling a customer's Ethernet traffic via an
Ethernet access network is to add an additional VLAN tag to the
customer's data (which may be either tagged or untagged). The
additional tag is referred to as Provider's VLAN (P-VLAN). Inside
the provider's network each P-VLAN designates a customer or more
specifically a VPLS instance for that customer. Therefore, there
is a one-to-one correspondence between a P-VLAN and a VPLS
instance. In this model, the MTU-s needs to have the capability of
adding the additional P-VLAN tag to non-multiplexed ACs where
customer VLANs are not used as service delimiters. This
functionality is described in [802.1ad].
If customer VLANs need to be treated as service delimiters (e.g.,
the AC is a multiplexed port), then the MTU-s needs to have the
Lasserre, et al. [Page 21]
Internet Draft Virtual Private LAN Service over LDP June 2006
additional capability of translating a customer VLAN (C-VLAN) to a
P-VLAN, or push an additional P-VLAN tag, in order to resolve
overlapping VLAN tags used by different customers. Therefore, the
MTU-s in this model can be considered as a typical bridge with this
additional capability. This functionality is described in
[802.1ad].
The PE-rs needs to be able to perform bridging functionality over
the standard Ethernet ports toward the access network as well as
over the PWs toward the network core. In this model, the PE-rs may
need to run STP towards the access network, in addition to split-
horizon over the MPLS core. The PE-rs needs to map a P-VLAN to a
VPLS-instance and its associated PWs and vice versa.
The details regarding bridge operation for MTU-s and PE-rs (e.g.,
encapsulation format for Q-in-Q messages, customer's Ethernet
control protocol handling, etc.) are outside of the scope of this
document and they are covered in [802.1ad]. However, the relevant
part is the interaction between the bridge module and the MPLS/IP
PWs in the PE-rs, which behaves just as in a regular VPLS.
11.1. Scalability
Since each P-VLAN corresponds to a VPLS instance, the total number
of VPLS instances supported is limited to 4K. The P-VLAN serves as
a local service delimiter within the provider's network that is
stripped as it gets mapped to a PW in a VPLS instance. Therefore,
the 4K limit applies only within an Ethernet access network
(Ethernet island) and not to the entire network. The SP network
consists of a core MPLS/IP network that connects many Ethernet
islands. Therefore, the number of VPLS instances can scale
accordingly with the number of Ethernet islands (a metro region can
be represented by one or more islands).
11.2. Dual Homing and Failure Recovery
In this model, an MTU-s can be dual homed to different devices
(aggregators and/or PE-rs devices). The failure protection for
access network nodes and links can be provided through running STP
in each island. The STP of each island is independent from other
islands and do not interact with each other. If an island has more
than one PE-rs, then a dedicated full-mesh of PWs is used among
these PE-rs devices for carrying the SP BPDU packets for that
island. On a per P-VLAN basis, STP will designate a single PE-rs
to be used for carrying the traffic across the core. The loop-free
protection through the core is performed using split-horizon and
the failure protection in the core is performed through standard
IP/MPLS re-routing.
12. Contributors
Loa Andersson, TLA
Ron Haberman, Alcatel
Lasserre, et al. [Page 22]
Internet Draft Virtual Private LAN Service over LDP June 2006
Juha Heinanen, Independent
Giles Heron, Tellabs
Sunil Khandekar, Alcatel
Luca Martini, Cisco
Pascal Menezes, Independent
Rob Nath, Lucent
Eric Puetz, SBC
Vasile Radoaca, Independent
Ali Sajassi, Cisco
Yetik Serbest, SBC
Nick Slabakov, Juniper
Andrew Smith, Consultant
Tom Soon, SBC
Nick Tingle, Alcatel
13. Acknowledgments
We wish to thank Joe Regan, Kireeti Kompella, Anoop Ghanwani, Joel
Halpern, Bill Hong, Rick Wilder, Jim Guichard, Steve Phillips, Norm
Finn, Matt Squire, Muneyoshi Suzuki, Waldemar Augustyn, Eric Rosen,
Yakov Rekhter, Sasha Vainshtein, and Du Wenhua for their valuable
feedback.
We would also like to thank Rajiv Papneja (ISOCORE), Winston Liu
(Ixia), and Charlie Hundall for identifying issues with the draft
in the course of the interoperability tests.
We would also like to thank Ina Minei, Bob Thomas, Eric Gray and
Dimitri Papadimitriou for their thorough technical review of the
document.
14. Security Considerations
A more comprehensive description of the security issues involved in
L2VPNs is covered in [VPN-SEC]. An unguarded VPLS service is
vulnerable to some security issues which pose risks to the customer
and provider networks. Most of the security issues can be avoided
through implementation of appropriate guards. A couple of them can
be prevented through existing protocols.
- Data plane aspects
- Traffic isolation between VPLS domains is guaranteed by
the use of per VPLS L2 FIB table and the use of per VPLS
PWs
- The customer traffic, which consists of Ethernet frames,
is carried unchanged over VPLS. If security is
required, the customer traffic SHOULD be encrypted
and/or authenticated before entering the service
provider network
Lasserre, et al. [Page 23]
Internet Draft Virtual Private LAN Service over LDP June 2006
- Preventing broadcast storms can be achieved by using
routers as CPE devices or by rate policing the amount of
broadcast traffic that customers can send
- Control plane aspects
- LDP security (authentication) methods as described in
[RFC3036] SHOULD be applied. This would prevent
unauthenticated messages from disrupting a PE in a VPLS
- Denial of service attacks
- Some means to limit the number of MAC addresses (per site
per VPLS) that a PE can learn SHOULD be implemented
15. IANA Considerations
The type field in the MAC List TLV is defined as 0x404 in section
6.2.1 and is subject to IANA approval.
16. References
16.1. Normative References
[RFC4447] "Pseudowire Setup and Maintenance Using the Label
Distribution Protocol (LDP)", L. Martini, et al., April 2006.
[RFC4448] "Encapsulation Methods for Transport of Ethernet over
MPLS Networks", L. Martini, et al., RFC 4448, April 2006.
[802.1D-ORIG] Original 802.1D - ISO/IEC 10038, ANSI/IEEE Std
802.1D-1993 "MAC Bridges".
[802.1D-REV] 802.1D - "Information technology - Telecommunications
and information exchange between systems - Local and metropolitan
area networks - Common specifications - Part 3: Media Access
Control (MAC) Bridges: Revision. This is a revision of ISO/IEC
10038: 1993, 802.1j-1992 and 802.6k-1992. It incorporates
P802.11c, P802.1p and P802.12e." ISO/IEC 15802-3: 1998.
[802.1Q] 802.1Q - ANSI/IEEE Draft Standard P802.1Q/D11, "IEEE
Standards for Local and Metropolitan Area Networks: Virtual Bridged
Local Area Networks", July 1998.
[RFC3036] "LDP Specification", L. Andersson, et al., RFC 3036,
January 2001.
[IANA] "IANA Allocations for pseudo Wire Edge to Edge Emulation
(PWE3)" Martini,Townsley, draft-ietf-pwe3-iana-allocation-08.txt,
Work in progress, February 2005.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
Lasserre, et al. [Page 24]
Internet Draft Virtual Private LAN Service over LDP June 2006
16.2. Informative References
[BGP-VPN] "BGP/MPLS VPNs", draft-ietf-l3vpn-rfc2547bis-03.txt, Work
in Progress, October 2004.
[RADIUS-DISC] "Using Radius for PE-Based VPN Discovery", draft-
ietf-l2vpn-radius-pe-discovery-01.txt, Work in Progress, February
2005.
[BGP-DISC] "Using BGP as an Auto-Discovery Mechanism for Network-
based VPNs", draft-ietf-l3vpn-bgpvpn-auto-06.txt, Work in Progress,
June 2005.
[L2FRAME] "Framework for Layer 2 Virtual Private Networks
(L2VPNs)", draft-ietf-l2vpn-l2-framework-05, Work in Progress, June
2004.
[L2VPN-REQ] "Service Requirements for Layer-2 Provider Provisioned
Virtual Private Networks", draft-ietf-l2vpn-requirements-04.txt,
Work in Progress, October 2005.
[VPN-SEC] "Security Framework for Provider Provisioned Virtual
Private Networks", draft-ietf-l3vpn-security-framework-03.txt, Work
in Progress, November 2004.
[802.1ad] "IEEE standard for Provider Bridges", Work in Progress,
December 2002.
17. Appendix: VPLS Signaling using the PWid FEC Element
This section is being retained because live deployments use this
version of the signaling for VPLS.
The VPLS signaling information is carried in a Label Mapping
message sent in downstream unsolicited mode, which contains the
following PWid FEC TLV.
PW, C, PW Info Length, Group ID, Interface parameters are as
defined in [RFC4447].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PW TLV |C| PW Type |PW info Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PWID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Interface parameters |
~ ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Lasserre, et al. [Page 25]
Internet Draft Virtual Private LAN Service over LDP June 2006
We use the Ethernet PW type to identify PWs that carry Ethernet
traffic for multipoint connectivity.
In a VPLS, we use a VCID (which, when using the PWid FEC, has been
substituted with a more general identifier (AGI), to address
extending the scope of a VPLS) to identify an emulated LAN segment.
Note that the VCID as specified in [RFC4447] is a service
identifier, identifying a service emulating a point-to-point
virtual circuit. In a VPLS, the VCID is a single service
identifier, so it has global significance across all PEs involved
in the VPLS instance.
18. Authors' Addresses
Marc Lasserre
Lucent Technologies
Email: mlasserre@lucent.com
Vach Kompella
Alcatel
Email: vach.kompella@alcatel.com
IPR Disclosure Acknowledgement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed
to pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; nor does it represent that
it has made any independent effort to identify any such rights.
Information on the procedures with respect to rights in RFC
documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository
at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
ipr@ietf.org.
Copyright Notice
Copyright (C) The Internet Society (2006). This document is
subject to the rights, licenses and restrictions contained in BCP
78, and except as set forth therein, the authors retain all their
rights.
Lasserre, et al. [Page 26]
Internet Draft Virtual Private LAN Service over LDP June 2006
Disclaimer
This document and the information contained herein are provided on
an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT
THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
Lasserre, et al. [Page 27]