Internet Engineering Task Force F. Maino, Ed.
Internet-Draft Cisco
Intended status: Standards Track J. Lemon
Expires: July 9, 2020 Broadcom
P. Agarwal
Innovium
D. Lewis
M. Smith
Cisco
January 6, 2020
LISP Generic Protocol Extension
draft-ietf-lisp-gpe-13
Abstract
This document describes extentions to the Locator/ID Separation
Protocol (LISP) Data-Plane, via changes to the LISP header, to
support multi-protocol encapsulation.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 9, 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Maino, et al. Expires July 9, 2020 [Page 1]
Internet-Draft LISP Generic Protocol Extension January 2020
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Conventions . . . . . . . . . . . . . . . . . . . . . . . 3
1.2. Definition of Terms . . . . . . . . . . . . . . . . . . . 3
2. LISP Header Without Protocol Extensions . . . . . . . . . . . 3
3. Generic Protocol Extension for LISP (LISP-GPE) . . . . . . . 4
4. Implementation and Deployment Considerations . . . . . . . . 6
4.1. Applicability Statement . . . . . . . . . . . . . . . . . 6
4.2. Congestion Control Functionality . . . . . . . . . . . . 7
4.3. UDP Checksum . . . . . . . . . . . . . . . . . . . . . . 7
4.3.1. UDP Zero Checksum Handling with IPv6 . . . . . . . . 8
4.4. Ethernet Encapsulated Payloads . . . . . . . . . . . . . 9
5. Backward Compatibility . . . . . . . . . . . . . . . . . . . 10
5.1. Detection of ETR Capabilities . . . . . . . . . . . . . . 10
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
6.1. LISP-GPE Next Protocol Registry . . . . . . . . . . . . . 10
7. Security Considerations . . . . . . . . . . . . . . . . . . . 10
8. Acknowledgements and Contributors . . . . . . . . . . . . . . 11
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 11
9.1. Normative References . . . . . . . . . . . . . . . . . . 11
9.2. Informative References . . . . . . . . . . . . . . . . . 12
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 13
1. Introduction
The LISP Data-Plane is defined in [I-D.ietf-lisp-rfc6830bis]. It
specifies an encapsulation format that carries IPv4 or IPv6 packets
(henceforth jointly referred to as IP) in a LISP header and outer
UDP/IP transport.
The LISP Data-Plane header does not specify the protocol being
encapsulated and therefore is currently limited to encapsulating only
IP packet payloads. Other protocols, most notably Virtual eXtensible
Local Area Network (VXLAN) [RFC7348] (which defines a similar header
format to LISP), are used to encapsulate Layer-2 (L2) protocols such
as Ethernet.
This document defines an extension for the LISP header, as defined in
[I-D.ietf-lisp-rfc6830bis], to indicate the inner protocol, enabling
the encapsulation of Ethernet, IP or any other desired protocol all
the while ensuring compatibility with existing LISP deployments.
Maino, et al. Expires July 9, 2020 [Page 2]
Internet-Draft LISP Generic Protocol Extension January 2020
A flag in the LISP header, called the P-bit, is used to signal the
presence of the 8-bit Next Protocol field. The Next Protocol field,
when present, uses 8 bits of the field that was allocated to the
echo-noncing and map-versioning features in
[I-D.ietf-lisp-rfc6830bis]. Those two features are no longer
available when the P-bit is used. However, appropriate LISP-GPE shim
headers can be defined to specify capabilities that are equivalent to
echo-noncing and/or map-versioning.
Since all of the reserved bits of the LISP Data-Plane header have
been allocated, LISP-GPE can also be used to extend the LISP Data-
Plane header by defining Next Protocol "shim" headers that implements
new data plane functions not supported in the LISP header. For
example, the use of the Group-Based Policy (GBP) header
[I-D.lemon-vxlan-lisp-gpe-gbp] or of the In-situ Operations,
Administration, and Maintenance (IOAM) header
[I-D.brockners-ippm-ioam-vxlan-gpe] with LISP-GPE, can be considered
an extension to add support in the Data-Plane for Group-Based Policy
functionalities or IOAM metadata.
1.1. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
1.2. Definition of Terms
This document uses terms already defined in
[I-D.ietf-lisp-rfc6830bis].
2. LISP Header Without Protocol Extensions
As described in Section 1, the LISP header has no protocol identifier
that indicates the type of payload being carried. Because of this,
LISP is limited to carrying IP payloads.
The LISP header [I-D.ietf-lisp-rfc6830bis] contains a series of flags
(some defined, some reserved), a Nonce/Map-version field and an
instance ID/Locator-status-bit field. The flags provide flexibility
to define how the various fields are encoded. Notably, Flag bit 5 is
the last reserved bit in the LISP header.
Maino, et al. Expires July 9, 2020 [Page 3]
Internet-Draft LISP Generic Protocol Extension January 2020
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|N|L|E|V|I|R|K|K| Nonce/Map-Version |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Instance ID/Locator-Status-Bits |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: LISP Header
3. Generic Protocol Extension for LISP (LISP-GPE)
This document defines two changes to the LISP header in order to
support multi-protocol encapsulation: the introduction of the P-bit
and the definition of a Next Protocol field. This document specifies
the protocol behavior when the P-bit is set to 1, no changes are
introduced when the P-bit is set to 0. The LISP-GPE header is shown
in Figure 2 and described below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|N|L|E|V|I|P|K|K| Reserved | Next Protocol |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Instance ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: LISP-GPE Header
P-Bit: Flag bit 5 is defined as the Next Protocol bit. The P-bit is
set to 1 to indicate the presence of the 8 bit Next Protocol
field.
If the P-bit is clear (0) the LISP header is bit-by-bit equivalent
to the definition in [I-D.ietf-lisp-rfc6830bis].
When the P-bit is set to 1, bits N, E, and V MUST be set zero on
transmission and ignored on receipt. Features equivalent to those
that were implemented with bits N,E and V in
[I-D.ietf-lisp-rfc6830bis], such as echo-noncing and map-
versioning, can be implemented by defining appropriate LISP-GPE
shim headers.
Maino, et al. Expires July 9, 2020 [Page 4]
Internet-Draft LISP Generic Protocol Extension January 2020
Next Protocol: The lower 8 bits of the first 32-bit word are used to
carry a Next Protocol. This Next Protocol field contains the
protocol of the encapsulated payload packet.
This document defines the following Next Protocol values:
0x01 : IPv4
0x02 : IPv6
0x03 : Ethernet
0x04 : Network Service Header (NSH) [RFC8300]
0x05 to 0x7F: Unassigned
0x80 to 0xFF: Unassigned (shim headers)
The values are tracked in the IANA LISP-GPE Next Protocol Registry
as described in Section 6.1.
Next protocol values from Ox80 to 0xFF are assigned to protocols
encoded as generic "shim" headers. All shim protocols MUST use the
header structure in Figure 3, which includes a Next Protocol field.
When a shim header is used with other protocols identified by next
protocol values from 0x0 to 0x7F, the shim header MUST come before
the further protocol, and the next header of the shim will indicate
which protocol follows the shim header.
Shim headers can be used to incrementally deploy new GPE features,
keeping the processing of shim headers known to a given xTR
implementation in the 'fast' path (typically an ASIC), while punting
the processing of the remaining new GPE features to the 'slow' path.
Shim protocols MUST have the first 32 bits defined as:
Maino, et al. Expires July 9, 2020 [Page 5]
Internet-Draft LISP Generic Protocol Extension January 2020
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Reserved | Next Protocol |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Protocol Specific Fields ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Shim Header
Where:
Type: This field identifies the different messages of this protocol.
Length: The length, in 4-octect units, of this protocol message not
including the first 4 octects.
Reserved: The use of this field is reserved to the protocol defined
in this message.
Next Protocol Field: The next protocol field contains the protocol
of the encapsulated payload. The values are tracked in the IANA
LISP-GPE Next Protocol Registry as described in Section 6.1.
4. Implementation and Deployment Considerations
4.1. Applicability Statement
LISP-GPE conforms, as an UDP-based encapsulation protocol, to the UDP
usage guidelines as specified in [RFC8085]. The applicability of
these guidelines are dependent on the underlay IP network and the
nature of the encapsulated payload.
[RFC8085] outlines two applicability scenarios for UDP applications,
1) general Internet and 2) controlled environment. The controlled
environment means a single administrative domain or adjacent set of
cooperating domains. A network in a controlled environment can be
managed to operate under certain conditions whereas in general
Internet this cannot be done. Hence requirements for a tunnel
protocol operating under a controlled environment can be less
restrictive than the requirements of general internet.
LISP-GPE scope of applicability is the same set of use cases covered
by[I-D.ietf-lisp-rfc6830bis] for the LISP dataplane protocol. The
common property of these use cases is a large set of cooperating
entities seeking to communicate over the public Internet or other
Maino, et al. Expires July 9, 2020 [Page 6]
Internet-Draft LISP Generic Protocol Extension January 2020
large underlay IP infrastructures, while keeping the addressing and
topology of the cooperating entities separate from the underlay and
Internet topology, routing, and addressing.
LISP-GPE is meant to be deployed in network environments operated by
a single operator or adjacent set of cooperating network operators
that fits with the definition of controlled environments in
[RFC8085].
For the purpose of this document, a traffic-managed controlled
environment (TMCE), outlined in [RFC8086], is defined as an IP
network that is traffic-engineered and/or otherwise managed (e.g.,
via use of traffic rate limiters) to avoid congestion. Significant
portions of text in this Section are based on [RFC8086].
It is the responsibility of the network operators to ensure that the
guidelines/requirements in this section are followed as applicable to
their LISP-GPE deployments
4.2. Congestion Control Functionality
LISP-GPE does not natively provide congestion control functionality
and relies on the payload protocol traffic for congestion control.
As such LISP-GPE MUST be used with congestion controlled traffic or
within a network that is traffic managed to avoid congestion (TMCE).
An operator of a traffic managed network (TMCE) may avoid congestion
by careful provisioning of their networks, rate-limiting of user data
traffic and traffic engineering according to path capacity.
Encapsulated payloads may have Explicit Congestion Notification
mechanisms that may or may not be mapped to the outer IP header ECN
field. Such new encapsulated payolads, when registered with LISP-
GPE, MUST be accompanied by a set of guidelines derived from
[I-D.ietf-tsvwg-ecn-encap-guidelines] and [RFC6040].
4.3. UDP Checksum
For IP payloads, section 5.3 of [I-D.ietf-lisp-rfc6830bis] specifies
how to handle UDP Checksums encouraging implementors to consider UDP
checksum usage guidelines in section 3.4 of [RFC8085] when it is
desirable to protect UDP and LISP headers against corruption.
In order to provide integrity of LISP-GPE headers, options and
payload, for example to avoid mis-delivery of payload to different
tenant systems in case of data corruption, outer UDP checksum SHOULD
be used with LISP-GPE when transported over IPv4. The UDP checksum
provides a statistical guarantee that a payload was not corrupted in
transit. These integrity checks are not strong from a coding or
Maino, et al. Expires July 9, 2020 [Page 7]
Internet-Draft LISP Generic Protocol Extension January 2020
cryptographic perspective and are not designed to detect physical-
layer errors or malicious modification of the datagram (see
Section 3.4 of [RFC8085]). In deployments where such a risk exists,
an operator SHOULD use additional data integrity mechanisms such as
offered by IPSec.
An operator MAY choose to disable UDP checksum and use zero checksum
if LISP-GPE packet integrity is provided by other data integrity
mechanisms such as IPsec or additional checksums or if one of the
conditions in Section 4.3.1 a, b, c are met.
By default, UDP checksum MUST be used when LISP-GPE is transported
over IPv6. A tunnel endpoint MAY be configured for use with zero UDP
checksum if additional requirements in Section 4.3.1 are met.
4.3.1. UDP Zero Checksum Handling with IPv6
When LISP-GPE is used over IPv6, UDP checksum is used to protect IPv6
headers, UDP headers and LISP-GPE headers and payload from potential
data corruption. As such by default LISP-GPE MUST use UDP checksum
when transported over IPv6. An operator MAY choose to configure to
operate with zero UDP checksum if operating in a traffic managed
controlled environment as stated in Section 4.1 if one of the
following conditions are met:
a. It is known that the packet corruption is exceptionally unlikely
(perhaps based on knowledge of equipment types in their underlay
network) and the operator is willing to take a risk of undetected
packet corruption
b. It is judged through observational measurements (perhaps through
historic or current traffic flows that use non zero checksum)
that the level of packet corruption is tolerably low and where
the operator is willing to take the risk of undetected corruption
c. LISP-GPE payload is carrying applications that are tolerant of
misdelivered or corrupted packets (perhaps through higher layer
checksum validation and/or reliability through retransmission)
In addition LISP-GPE tunnel implementations using Zero UDP checksum
MUST meet the following requirements:
1. Use of UDP checksum over IPv6 MUST be the default configuration
for all LISP-GPE tunnels
2. If LISP-GPE is used with zero UDP checksum over IPv6 then such
xTR implementation MUST meet all the requirements specified in
Maino, et al. Expires July 9, 2020 [Page 8]
Internet-Draft LISP Generic Protocol Extension January 2020
section 4 of [RFC6936] and requirements 1 as specified in section
5 of [RFC6936]
3. The ETR that decapsulates the packet SHOULD check the source and
destination IPv6 addresses are valid for the LISP-GPE tunnel that
is configured to receive Zero UDP checksum and discard other
packets for which such check fails
4. The ITR that encapsulates the packet MAY use different IPv6
source addresses for each LISP-GPE tunnel that uses Zero UDP
checksum mode in order to strengthen the decapsulator's check of
the IPv6 source address (i.e the same IPv6 source address is not
to be used with more than one IPv6 destination address,
irrespective of whether that destination address is a unicast or
multicast address). When this is not possible, it is RECOMMENDED
to use each source address for as few LISP-GPE tunnels that use
zero UDP checksum as is feasible
5. Measures SHOULD be taken to prevent LISP-GPE traffic over IPv6
with zero UDP checksum from escaping into the general Internet.
Examples of such measures include employing packet filters at the
PETR and/or keeping logical or physical separation of LISP
network from networks carrying General Internet
The above requirements do not change either the requirements
specified in [RFC2460] as modified by [RFC6935] or the requirements
specified in [RFC6936].
The requirement to check the source IPv6 address in addition to the
destination IPv6 address, plus the recommendation against reuse of
source IPv6 addresses among LISP-GPE tunnels collectively provide
some mitigation for the absence of UDP checksum coverage of the IPv6
header. A traffic-managed controlled environment that satisfies at
least one of three conditions listed at the beginning of this section
provides additional assurance.
4.4. Ethernet Encapsulated Payloads
When a LISP-GPE router performs Ethernet encapsulation, the inner
802.1Q [IEEE.802.1Q_2014] 3-bit priority code point (PCP) field MAY
be mapped from the encapsulated frame to the 3-bit Type of Service
field in the outer IPv4 header, or in the case of IPv6 the 'Traffic
Class' field.
When a LISP-GPE router performs Ethernet encapsulation, the inner
header 802.1Q [IEEE.802.1Q_2014] VLAN Identifier (VID) MAY be mapped
to, or used to determine the LISP Instance IDentifier (IID) field.
Maino, et al. Expires July 9, 2020 [Page 9]
Internet-Draft LISP Generic Protocol Extension January 2020
5. Backward Compatibility
LISP-GPE uses the same UDP destination port (4341) allocated to LISP.
When encapsulating IP packets to a non LISP-GPE capable router the
P-bit MUST be set to 0. That is, the encapsulation format defined in
this document MUST NOT be sent to a router that has not indicated
that it supports this specification because such a router would
ignore the P-bit (as described in [I-D.ietf-lisp-rfc6830bis]) and so
would misinterpret the other LISP header fields possibly causing
significant errors.
5.1. Detection of ETR Capabilities
The discovery of xTR capabilities to support LISP-GPE is out of the
scope of this document. Given that the applicability domain of LISP-
GPE is a traffic-managed controlled environment, ITR/ETR (xTR)
configuration mechanisms may be used for this purpose.
6. IANA Considerations
6.1. LISP-GPE Next Protocol Registry
IANA is requested to set up a registry of LISP-GPE "Next Protocol".
These are 8-bit values. Next Protocol values in the table below are
defined in this document. New values are assigned under the
Specification Required policy [RFC8126]. The protocols that are
being assigned values do not themselves need to be IETF standards
track protocols.
+---------------+-------------+---------------+
| Next Protocol | Description | Reference |
+---------------+-------------+---------------+
| 0x00 | Reserved | This Document |
| 0x01 | IPv4 | This Document |
| 0x02 | IPv6 | This Document |
| 0x03 | Ethernet | This Document |
| 0x04 | NSH | This Document |
| 0x05..0x7F | Unassigned | |
| 0x82..0xFF | Unassigned | |
+---------------+-------------+---------------+
7. Security Considerations
LISP-GPE security considerations are similar to the LISP security
considerations and mitigation techniques documented in [RFC7835].
Maino, et al. Expires July 9, 2020 [Page 10]
Internet-Draft LISP Generic Protocol Extension January 2020
LISP-GPE, as many encapsulations that use optional extensions, is
subject to on-path adversaries that by manipulating the P-Bit and the
packet itself can remove part of the payload or claim to encapsulate
any protocol payload type. Typical integrity protection mechanisms
(such as IPsec) SHOULD be used in combination with LISP-GPE by those
protocol extensions that want to protect from on-path attackers.
With LISP-GPE, issues such as data-plane spoofing, flooding, and
traffic redirection may depend on the particular protocol payload
encapsulated.
8. Acknowledgements and Contributors
A special thank you goes to Dino Farinacci for his guidance and
detailed review.
This Working Group (WG) document originated as draft-lewis-lisp-gpe;
the following are its coauthors and contributors along with their
respective affiliations at the time of WG adoption. The editor of
this document would like to thank and recognize them and their
contributions. These coauthors and contributors provided invaluable
concepts and content for this document's creation.
o Darrel Lewis, Cisco Systems, Inc.
o Fabio Maino, Cisco Systems, Inc.
o Paul Quinn, Cisco Systems, Inc.
o Michael Smith, Cisco Systems, Inc.
o Navindra Yadav, Cisco Systems, Inc.
o Larry Kreeger
o John Lemon, Broadcom
o Puneet Agarwal, Innovium
9. References
9.1. Normative References
[I-D.ietf-lisp-rfc6830bis]
Farinacci, D., Fuller, V., Meyer, D., Lewis, D., and A.
Cabellos-Aparicio, "The Locator/ID Separation Protocol
(LISP)", draft-ietf-lisp-rfc6830bis-28 (work in progress),
November 2019.
Maino, et al. Expires July 9, 2020 [Page 11]
Internet-Draft LISP Generic Protocol Extension January 2020
[IEEE.802.1Q_2014]
IEEE, "IEEE Standard for Local and metropolitan area
networks--Bridges and Bridged Networks", IEEE 802.1Q-2014,
DOI 10.1109/ieeestd.2014.6991462, December 2014,
<http://ieeexplore.ieee.org/servlet/
opac?punumber=6991460>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC6040] Briscoe, B., "Tunnelling of Explicit Congestion
Notification", RFC 6040, DOI 10.17487/RFC6040, November
2010, <https://www.rfc-editor.org/info/rfc6040>.
9.2. Informative References
[I-D.brockners-ippm-ioam-vxlan-gpe]
Brockners, F., Bhandari, S., Govindan, V., Pignataro, C.,
Gredler, H., Leddy, J., Youell, S., Mizrahi, T., Kfir, A.,
Gafni, B., Lapukhov, P., and M. Spiegel, "VXLAN-GPE
Encapsulation for In-situ OAM Data", draft-brockners-ippm-
ioam-vxlan-gpe-03 (work in progress), November 2019.
[I-D.ietf-tsvwg-ecn-encap-guidelines]
Briscoe, B., Kaippallimalil, J., and P. Thaler,
"Guidelines for Adding Congestion Notification to
Protocols that Encapsulate IP", draft-ietf-tsvwg-ecn-
encap-guidelines-13 (work in progress), May 2019.
[I-D.lemon-vxlan-lisp-gpe-gbp]
Lemon, J., Maino, F., Smith, M., and A. Isaac, "Group
Policy Encoding with VXLAN-GPE and LISP-GPE", draft-lemon-
vxlan-lisp-gpe-gbp-02 (work in progress), April 2019.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
December 1998, <https://www.rfc-editor.org/info/rfc2460>.
[RFC6935] Eubanks, M., Chimento, P., and M. Westerlund, "IPv6 and
UDP Checksums for Tunneled Packets", RFC 6935,
DOI 10.17487/RFC6935, April 2013,
<https://www.rfc-editor.org/info/rfc6935>.
Maino, et al. Expires July 9, 2020 [Page 12]
Internet-Draft LISP Generic Protocol Extension January 2020
[RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement
for the Use of IPv6 UDP Datagrams with Zero Checksums",
RFC 6936, DOI 10.17487/RFC6936, April 2013,
<https://www.rfc-editor.org/info/rfc6936>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC7835] Saucez, D., Iannone, L., and O. Bonaventure, "Locator/ID
Separation Protocol (LISP) Threat Analysis", RFC 7835,
DOI 10.17487/RFC7835, April 2016,
<https://www.rfc-editor.org/info/rfc7835>.
[RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage
Guidelines", BCP 145, RFC 8085, DOI 10.17487/RFC8085,
March 2017, <https://www.rfc-editor.org/info/rfc8085>.
[RFC8086] Yong, L., Ed., Crabbe, E., Xu, X., and T. Herbert, "GRE-
in-UDP Encapsulation", RFC 8086, DOI 10.17487/RFC8086,
March 2017, <https://www.rfc-editor.org/info/rfc8086>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8300] Quinn, P., Ed., Elzur, U., Ed., and C. Pignataro, Ed.,
"Network Service Header (NSH)", RFC 8300,
DOI 10.17487/RFC8300, January 2018,
<https://www.rfc-editor.org/info/rfc8300>.
Authors' Addresses
Fabio Maino (editor)
Cisco Systems
San Jose, CA 95134
USA
Email: fmaino@cisco.com
Maino, et al. Expires July 9, 2020 [Page 13]
Internet-Draft LISP Generic Protocol Extension January 2020
Jennifer Lemon
Broadcom
270 Innovation Drive
San Jose, CA 95134
USA
Email: jennifer.lemon@broadcom.com
Puneet Agarwal
Innovium
USA
Email: puneet@acm.org
Darrel Lewis
Cisco Systems
Email: darlewis@cisco.com
Michael Smith
Cisco Systems
Email: michsmit@cisco.com
Maino, et al. Expires July 9, 2020 [Page 14]