Network Working Group D. Farinacci
Internet-Draft D. Meyer
Intended status: Experimental J. Zwiebel
Expires: December 22, 2011 S. Venaas
cisco Systems
June 20, 2011
LISP for Multicast Environments
draft-ietf-lisp-multicast-06
Abstract
This draft describes how inter-domain multicast routing will function
in an environment where Locator/ID Separation is deployed using the
LISP architecture.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 22, 2011.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Farinacci, et al. Expires December 22, 2011 [Page 1]
Internet-Draft LISP for Multicast Environments June 2011
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
Table of Contents
1. Requirements Notation . . . . . . . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Definition of Terms . . . . . . . . . . . . . . . . . . . . . 7
4. Basic Overview . . . . . . . . . . . . . . . . . . . . . . . . 10
5. Source Addresses versus Group Addresses . . . . . . . . . . . 13
6. Locator Reachability Implications on LISP-Multicast . . . . . 14
7. Multicast Protocol Changes . . . . . . . . . . . . . . . . . . 15
8. LISP-Multicast Data-Plane Architecture . . . . . . . . . . . . 17
8.1. ITR Forwarding Procedure . . . . . . . . . . . . . . . . . 17
8.1.1. Multiple RLOCs for an ITR . . . . . . . . . . . . . . 17
8.1.2. Multiple ITRs for a LISP Source Site . . . . . . . . . 18
8.2. ETR Forwarding Procedure . . . . . . . . . . . . . . . . . 18
8.3. Replication Locations . . . . . . . . . . . . . . . . . . 19
9. LISP-Multicast Interworking . . . . . . . . . . . . . . . . . 20
9.1. LISP and non-LISP Mixed Sites . . . . . . . . . . . . . . 20
9.1.1. LISP Source Site to non-LISP Receiver Sites . . . . . 21
9.1.2. Non-LISP Source Site to non-LISP Receiver Sites . . . 22
9.1.3. Non-LISP Source Site to Any Receiver Site . . . . . . 23
9.1.4. Unicast LISP Source Site to Any Receiver Sites . . . . 24
9.1.5. LISP Source Site to Any Receiver Sites . . . . . . . . 24
9.2. LISP Sites with Mixed Address Families . . . . . . . . . . 25
9.3. Making a Multicast Interworking Decision . . . . . . . . . 27
10. Considerations when RP Addresses are Embedded in Group
Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . 28
11. Taking Advantage of Upgrades in the Core . . . . . . . . . . . 29
12. Mtrace Considerations . . . . . . . . . . . . . . . . . . . . 30
13. Security Considerations . . . . . . . . . . . . . . . . . . . 31
14. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 32
15. References . . . . . . . . . . . . . . . . . . . . . . . . . . 33
15.1. Normative References . . . . . . . . . . . . . . . . . . . 33
15.2. Informative References . . . . . . . . . . . . . . . . . . 33
Appendix A. Document Change Log . . . . . . . . . . . . . . . . . 35
A.1. Changes to draft-ietf-lisp-multicast-06.txt . . . . . . . 35
A.2. Changes to draft-ietf-lisp-multicast-05.txt . . . . . . . 35
A.3. Changes to draft-ietf-lisp-multicast-04.txt . . . . . . . 35
A.4. Changes to draft-ietf-lisp-multicast-03.txt . . . . . . . 35
A.5. Changes to draft-ietf-lisp-multicast-02.txt . . . . . . . 36
A.6. Changes to draft-ietf-lisp-multicast-01.txt . . . . . . . 36
Farinacci, et al. Expires December 22, 2011 [Page 2]
Internet-Draft LISP for Multicast Environments June 2011
A.7. Changes to draft-ietf-lisp-multicast-00.txt . . . . . . . 36
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 37
Farinacci, et al. Expires December 22, 2011 [Page 3]
Internet-Draft LISP for Multicast Environments June 2011
1. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Farinacci, et al. Expires December 22, 2011 [Page 4]
Internet-Draft LISP for Multicast Environments June 2011
2. Introduction
The Locator/ID Separation Architecture [LISP] provides a mechanism to
separate out Identification and Location semantics from the current
definition of an IP address. By creating two namespaces, an EID
namespace used by sites and a Locator (RLOC) namespace used by core
routing, the core routing infrastructure can scale by doing
topological aggregation of routing information.
Since LISP creates a new namespace, a mapping function must exist to
map a site's EID prefixes to its associated locators. For unicast
packets, both the source address and destination address must be
mapped. For multicast packets, only the source address needs to be
mapped. The destination group address doesn't need to be mapped
because the semantics of an IPv4 or IPv6 group address are logical in
nature and not topology-dependent. Therefore, this specifications
focuses on to map a source EID address of a multicast flow during
distribution tree setup and packet delivery.
This specification will address the following scenarios:
1. How a multicast source host in a LISP site sends multicast
packets to receivers inside of its site as well as to receivers
in other sites that are LISP enabled.
2. How inter-domain (or between LISP sites) multicast distribution
trees are built and how forwarding of multicast packets leaving a
source site toward receivers sites is performed.
3. What protocols are affected and what changes are required to such
multicast protocols.
4. How ASM-mode, SSM-mode, and Bidir-mode service models will
operate.
5. How multicast packet flow will occur for multiple combinations of
LISP and non-LISP capable source and receiver sites, for example:
A. How multicast packets from a source host in a LISP site are
sent to receivers in other sites when they are all non-LISP
sites.
B. How multicast packets from a source host in a LISP site are
sent to receivers in both LISP-enabled sites and non-LISP
sites.
C. How multicast packets from a source host in a non-LISP site
are sent to receivers in other sites when they are all LISP-
Farinacci, et al. Expires December 22, 2011 [Page 5]
Internet-Draft LISP for Multicast Environments June 2011
enabled sites.
D. How multicast packets from a source host in a non-LISP site
are sent to receivers in both LISP-enabled sites and non-LISP
sites.
This specification focuses on what changes are needed to the
multicast routing protocols to support LISP-Multicast as well as
other protocols used for inter-domain multicast, such as Multi-
protocol BGP (MBGP) [RFC4760]. The approach proposed in this
specification requires no changes to the multicast infrastructure
inside of a site when all sources and receivers reside in that site,
even when the site is LISP enabled. That is, internal operation of
multicast is unchanged regardless of whether or not the site is LISP
enabled or whether or not receivers exist in other sites which are
LISP-enabled.
Therefore, we see changes only to PIM-ASM [RFC4601], MSDP [RFC3618],
and PIM-SSM [RFC4607]. Bidir-PIM [RFC5015], which typically does not
run in an inter-domain environment is not addressed in depth in this
version of the specification.
Also, the current version of this specification does not describe
multicast-based Traffic Engineering relative to the TE-ITR and TE-ETR
descriptions in [LISP].
Farinacci, et al. Expires December 22, 2011 [Page 6]
Internet-Draft LISP for Multicast Environments June 2011
3. Definition of Terms
The terminology in this section is consistent with the definitions in
[LISP] but is extended specifically to deal with the application of
the terminology to multicast routing.
LISP-Multicast: a reference to the design in this specification.
That is, when any site that is participating in multicast
communication has been upgraded to be a LISP site, the operation
of control-plane and data-plane protocols is considered part of
the LISP-Multicast architecture.
Endpoint ID (EID): a 32-bit (for IPv4) or 128-bit (for IPv6) value
used in the source address field of the first (most inner) LISP
header of a multicast packet. The host obtains a destination
group address the same way it obtains one today, as it would when
it is a non-LISP site. The source EID is obtained via existing
mechanisms used to set a host's "local" IP address. An EID is
allocated to a host from an EID prefix block associated with the
site the host is located in. An EID can be used by a host to
refer to another host, as when it joins an SSM (S-EID,G) route
using IGMP version 3 [RFC4604]. LISP uses Provider Independent
(PI) blocks for EIDs; such EIDs MUST NOT be used as LISP RLOCs.
Note that EID blocks may be assigned in a hierarchical manner,
independent of the network topology, to facilitate scaling of the
mapping database. In addition, an EID block assigned to a site
may have site-local structure (subnetting) for routing within the
site; this structure is not visible to the global routing system.
Routing Locator (RLOC): the IPv4 or IPv6 address of an ingress
tunnel router (ITR), the router in the multicast source host's
site that encapsulates multicast packets. It is the output of a
EID-to-RLOC mapping lookup. An EID maps to one or more RLOCs.
Typically, RLOCs are numbered from topologically-aggregatable
blocks that are assigned to a site at each point to which it
attaches to the global Internet; where the topology is defined by
the connectivity of provider networks, RLOCs can be thought of as
Provider Assigned (PA) addresses. Multiple RLOCs can be assigned
to the same ITR device or to multiple ITR devices at a site.
Ingress Tunnel Router (ITR): a router which accepts an IP multicast
packet with a single IP header (more precisely, an IP packet that
does not contain a LISP header). The router treats this "inner"
IP destination multicast address opaquely so it doesn't need to
perform a map lookup on the group address because it is
topologically insignificant. The router then prepends an "outer"
IP header with one of its globally-routable RLOCs as the source
address field. This RLOC is known to other multicast receiver
Farinacci, et al. Expires December 22, 2011 [Page 7]
Internet-Draft LISP for Multicast Environments June 2011
sites which have used the mapping database to join a multicast
tree for which the ITR is the root. In general, an ITR receives
IP packets from site end systems on one side and sends LISP-
encapsulated multicast IP packets out all external interfaces
which have been joined.
An ITR would receive a multicast packet from a source inside of
its site when 1) it is on the path from the multicast source to
internally joined receivers, or 2) when it is on the path from the
multicast source to externally joined receivers.
Egress Tunnel Router (ETR): a router that is on the path from a
multicast source host in another site to a multicast receiver in
its own site. An ETR accepts a PIM Join/Prune message from a site
internal PIM router destined for the source's EID in the multicast
source site. The ETR maps the source EID in the Join/Prune
message to an RLOC address based on the EID-to-RLOC mapping. This
sets up the ETR to accept multicast encapsulated packets from the
ITR in the source multicast site. A multicast ETR decapsulates
multicast encapsulated packets and replicates them on interfaces
leading to internal receivers.
xTR: is a reference to an ITR or ETR when direction of data flow is
not part of the context description. xTR refers to the router that
is the tunnel endpoint. Used synonymously with the term "Tunnel
Router". For example, "An xTR can be located at the Customer Edge
(CE) router", meaning both ITR and ETR functionality can be at the
CE router.
LISP Header: a term used in this document to refer to the outer
IPv4 or IPv6 header, a UDP header, and a LISP header. An ITR
prepends headers and an ETR strips headers. A LISP encapsulated
multicast packet will have an "inner" header with the source EID
in the source field; an "outer" header with the source RLOC in the
source field: and the same globally unique group address in the
destination field of both the inner and outer header.
(S,G) State: the formal definition is in the PIM Sparse Mode
[RFC4601] specification. For this specification, the term is used
generally to refer to multicast state. Based on its topological
location, the (S,G) state resides in routers can be either
(S-EID,G) state (at a location where the (S,G) state resides) or
(S-RLOC,G) state (in the Internet core).
(S-EID,G) State: refers to multicast state in multicast source and
receiver sites where S-EID is the IP address of the multicast
source host (its EID). An S-EID can appear in an IGMPv3 report,
an MSDP SA message or a PIM Join/Prune message that travels inside
Farinacci, et al. Expires December 22, 2011 [Page 8]
Internet-Draft LISP for Multicast Environments June 2011
of a site.
(S-RLOC,G) State: refers to multicast state in the core where S is
a source locator (the IP address of a multicast ITR) of a site
with a multicast source. The (S-RLOC,G) is mapped from (S-EID,G)
entry by doing a mapping database lookup for the EID prefix that
S-EID maps to. An S-RLOC can appear in a PIM Join/Prune message
when it travels from an ETR to an ITR over the Internet core.
uLISP Site: a unicast only LISP site according to [LISP] which has
not deployed the procedures of this specification and therefore,
for multicast purposes, follows the procedures from Section 9.
mPETR: this is a multicast proxy-ETR that is responsible for
advertising a very coarse EID prefix which non-LISP and uLISP
sites can target their (S-EID,G) PIM Join/Prune message to. mPETRs
are used so LISP source multicast sites can send multicast packets
using source addresses from the EID namespace. mPETRs act as Proxy
ETRs for supporting multicast routing in a LISP infrastructure.
It is likely an uPITR [INTWORK] and a mPETR will be co-located
since the single device advertises a coarse EID-prefix in the
underlying unicast routing system.
Mixed Locator-Sets: this is a locator-set for a LISP database
mapping entry where the RLOC addresses in the locator-set are in
both IPv4 and IPv6 format.
Unicast Encapsulated PIM Join/Prune Message: this is a standard PIM
Join/Prune message (encapsulated in a LISP Encapsulated Control
Message with destination UDP port 4342) which is sent by ETRs at
multicast receiver sites to an ITR at a multicast source site.
This message is sent periodically as long as there are interfaces
in the oif-list for the (S-EID,G) entry the ETR is joining for.
Farinacci, et al. Expires December 22, 2011 [Page 9]
Internet-Draft LISP for Multicast Environments June 2011
4. Basic Overview
LISP, when used for unicast routing, increases the site's ability to
control ingress traffic flows. Egress traffic flows are controlled
by the IGP in the source site. For multicast, the IGP coupled with
PIM can decide which path multicast packets ingress. By using the
traffic engineering features of LISP, a multicast source site can
control the egress of its multicast traffic. By controlling the
priorities of locators from a mapping database entry, a source
multicast site can control which way multicast receiver sites join to
the source site.
At this point in time, we don't see a requirement for different
locator-sets, priority, and weight policies for multicast than we
have for unicast. However, when traffic engineering policies are
different for unicast versus multicast flows, it will be desirable to
use multicast-based priority and weight values in Map-Reply messages.
The fundamental multicast forwarding model is to encapsulate a
multicast packet into another multicast packet. An ITR will
encapsulate multicast packets received from sources that it serves in
another LISP multicast header. The destination group address from
the inner header is copied to the destination address of the outer
header. The inner source address is the EID of the multicast source
host and the outer source address is the RLOC of the encapsulating
ITR.
The LISP-Multicast architecture will follow this high-level protocol
and operational sequence:
1. Receiver hosts in multicast sites will join multicast content the
way they do today, they use IGMP. When they use IGMPv3 where
they specify source addresses, they use source EIDs, that is they
join (S-EID,G). If the multicast source is external to this
receiver site, the PIM Join/Prune message flows toward the ETRs,
finding the shortest exit (that is the closest exit for the Join/
Prune message and the closest entrance for the multicast packet
to the receiver).
2. The ETR does a mapping database lookup for S-EID. If the mapping
is cached from a previous lookup (from either a previous Join/
Prune for the source multicast site or a unicast packet that went
to the site), it will use the RLOC information from the mapping.
The ETR will use the same priority and weighting mechanism as for
unicast. So the source site can decide which way multicast
packets egress.
Farinacci, et al. Expires December 22, 2011 [Page 10]
Internet-Draft LISP for Multicast Environments June 2011
3. The ETR will build two PIM Join/Prune messages, one that contains
a (S-EID,G) entry that is unicast to the ITR that matches the
RLOC the ETR selects, and the other which contains a (S-RLOC,G)
entry so the core network can create multicast state from this
ETR to the ITR.
4. When the ITR gets the unicast Join/Prune message (see Section 3
for formal definition), it will process (S-EID,G) entries in the
message and propagate them inside of the site where it has
explicit routing information for EIDs via the IGP. When the ITR
receives the (S-RLOC,G) PIM Join/Prune message it will process it
like any other join it would get in today's Internet. The S-RLOC
address is the IP address of this ITR.
5. At this point there is (S-EID,G) state from the joining host in
the receiver multicast site to the ETR of the receiver multicast
site. There is (S-RLOC,G) state across the core network from the
ETR of the multicast receiver site to the ITR in the multicast
source site and (S-EID,G) state in the source multicast site.
Note, the (S-EID,G) state is the same S-EID in each multicast
site. As other ETRs join the same multicast tree, they can join
through the same ITR (in which case the packet replication is
done in the core) or a different ITR (in which case the packet
replication is done at the source site).
6. When a packet is originated by the multicast host in the source
site, it will flow to one or more ITRs which will prepend a LISP
header by copying the group address to the outer destination
address field and insert its own locator address in the outer
source address field. The ITR will look at its (S-RLOC,G) state,
where S-RLOC is its own locator address, and replicate the packet
on each interface a (S-RLOC,G) joined was received on. The core
has (S-RLOC,G) so where fanout occurs to multiple sites, a core
router will do packet replication.
7. When either the source site or the core replicates the packet,
the ETR will receive a LISP packet with a destination group
address. It will decapsulate packets because it has receivers
for the group. Otherwise, it would have not received the packets
because it would not have joined. The ETR decapsulates and does
a (S-EID,G) lookup in its multicast FIB to forward packets out
one or more interfaces to forward the packet to internal
receivers.
This architecture is consistent and scalable with the architecture
presented in [LISP] where multicast state in the core operates on
locators and multicast state at the sites operates on EIDs.
Farinacci, et al. Expires December 22, 2011 [Page 11]
Internet-Draft LISP for Multicast Environments June 2011
Alternatively, [LISP] also has a mechanism where (S-EID,G) state can
reside in the core through the use of RPF-vectors [RPFV] in PIM Join/
Prune messages. However, few PIM implementations support RPF vectors
and LISP should avoid S-EID state in the core. See Section 5 for
details.
However, we have some observations on the algorithm above. We can
scale the control plane but at the expense of sending data to sites
which may have not joined the distribution tree where the
encapsulated data is being delivered. For example, one site joins
(S-EID1,G) and another site joins (S-EID2,G). Both EIDs are in the
same multicast source site. Both multicast receiver sites join to
the same ITR with state (S-RLOC,G) where S-RLOC is the RLOC for the
ITR. The ITR joins both (S-EID1,G) and (S-EID2,G) inside of the
site. The ITR receives (S-RLOC,G) joins and populates the oif-list
state for it. Since both (S-EID1,G) and (S-EID2, G) map to the one
(S-RLOC,G) packets will be delivered by the core to both multicast
receiver sites even though each have joined a single source-based
distribution tree. This behavior is a consequence of the many-to-one
mapping between S-EIDs and a S-RLOC.
There is a possible solution to this problem which reduces the number
of many-to-one occurrences of (S-EID,G) entries aggregating into a
single (S-RLOC,G) entry. If a physical ITR can be assigned multiple
RLOC addresses and these addresses are advertised in mapping database
entries, then ETRs at receiver sites have more RLOC address options
and therefore can join different (RLOC,G) entries for each (S-EID,G)
entry joined at the receiver site. It would not scale to have a one-
to-one relationship between the number of S-EID sources at a source
site and the number of RLOCs assigned to all ITRs at the site, but we
can reduce the "n" to a smaller number in the "n-to-1" relationship.
And in turn, reduce the opportunity for data packets to be delivered
to sites for groups not joined.
Farinacci, et al. Expires December 22, 2011 [Page 12]
Internet-Draft LISP for Multicast Environments June 2011
5. Source Addresses versus Group Addresses
Multicast group addresses don't have to be associated with either the
EID or RLOC namespace. They actually are a namespace of their own
that can be treated as logical with relatively opaque allocation.
So, by their nature, they don't detract from an incremental
deployment of LISP-Multicast.
As for source addresses, as in the unicast LISP scenario, there is a
decoupling of identification from location. In a LISP site, packets
are originated from hosts using their allocated EIDs, those addresses
are used to identify the host as well as where in the site's topology
the host resides but not how and where it is attached to the
Internet.
Therefore, when multicast distribution tree state is created anywhere
in the network on the path from any multicast receiver to a multicast
source, EID state is maintained at the source and receiver multicast
sites, and RLOC state is maintained in the core. That is, a
multicast distribution tree will be represented as a 3-tuple of
{(S-EID,G) (S-RLOC,G) (S-EID,G)} where the first element of the
3-tuple is the state stored in routers from the source to one or more
ITRs in the source multicast site, the second element of the 3-tuple
is the state stored in routers downstream of the ITR, in the core, to
all LISP receiver multicast sites, and the third element in the
3-tuple is the state stored in the routers downstream of each ETR, in
each receiver multicast site, reaching each receiver. Note that
(S-EID,G) is the same in both the source and receiver multicast
sites.
The concatenation/mapping from the first element to the second
element of the 3-tuples is done by the ITR and from the second
element to the third element is done at the ETRs.
Farinacci, et al. Expires December 22, 2011 [Page 13]
Internet-Draft LISP for Multicast Environments June 2011
6. Locator Reachability Implications on LISP-Multicast
Multicast state as it is stored in the core is always (S,G) state as
it exists today or (S-RLOC,G) state as it will exist when LISP sites
are deployed. The core routers cannot distinguish one from the
other. They don't need to because it is state that RPFs against the
core routing tables in the RLOC namespace. The difference is where
the root of the distribution tree for a particular source is. In the
traditional multicast core, the source S is the source host's IP
address. For LISP-Multicast the source S is a single ITR of the
multicast source site.
An ITR is selected based on the LISP EID-to-RLOC mapping used when an
ETR propagates a PIM Join/Prune message out of a receiver multicast
site. The selection is based on the same algorithm an ITR would use
to select an ETR when sending a unicast packet to the site. In the
unicast case, the ITR can change on a per-packet basis depending on
the reachability of the ETR. So an ITR can change relatively easily
using local reachability state. However, in the multicast case, when
an ITR goes unreachable, new distribution tree state must be built
because the encapsulating root has changed. This is more significant
than an RPF-change event, where any router would typically locally
change its RPF-interface for its existing tree state. But when an
encapsulating LISP-Multicast ITR goes unreachable, new distribution
state must be rebuilt and reflect the new encapsulator. Therefore,
when an ITR goes unreachable, all ETRs that are currently joined to
that ITR will have to trigger a new Join/Prune message for (S-RLOC,G)
to the new ITR as well as send a unicast encapsulated Join/Prune
message telling the new ITR which (S-EID,G) is being joined.
This issue can be mitigated by using anycast addressing for the ITRs
so the problem does reduce to an RPF change in the core, but still
requires a unicast encapsulated Join/Prune message to tell the new
ITR about (S-EID,G). The problem with this approach is that the ETR
really doesn't know when the ITR has changed so the new anycast ITR
will get the (S-EID,G) state only when the ETR sends it the next time
during its periodic sending procedures.
Farinacci, et al. Expires December 22, 2011 [Page 14]
Internet-Draft LISP for Multicast Environments June 2011
7. Multicast Protocol Changes
A number of protocols are used today for inter-domain multicast
routing:
IGMPv1-v3, MLDv1-v2: These protocols do not require any changes for
LISP-Multicast for two reasons. One being that they are link-
local and not used over site boundaries and second they advertise
group addresses that don't need translation. Where source
addresses are supplied in IGMPv3 and MLDv2 messages, they are
semantically regarded as EIDs and don't need to be converted to
RLOCs until the multicast tree-building protocol, such as PIM, is
received by the ETR at the site boundary. Addresses used for IGMP
and MLD come out of the source site's allocated addresses which
are therefore from the EID namespace.
MBGP: Even though MBGP is not a multicast routing protocol, it is
used to find multicast sources when the unicast BGP peering
topology and the multicast MBGP peering topology are not
congruent. When MBGP is used in a LISP-Multicast environment, the
prefixes which are advertised are from the RLOC namespace. This
allows receiver multicast sites to find a path to the source
multicast site's ITRs. MBGP peering addresses will be from the
RLOC namespace.
MSDP: MSDP is used to announce active multicast sources to other
routing domains (or LISP sites). The announcements come from the
PIM Rendezvous Points (RPs) from sites where there are active
multicast sources sending to various groups. In the context of
LISP-Multicast, the source addresses advertised in MSDP will
semantically be from the EID namespace since they describe the
identity of a source multicast host. It will be true that the
state stored in MSDP caches from core routers will be from the EID
namespace. An RP address inside of site will be from the EID
namespace so it can be advertised and reached by internal unicast
routing mechanism. However, for MSDP peer-RPF checking to work
properly across sites, the RP addresses must be converted or
mapped into a routable address that is advertised and maintained
in the BGP routing tables in the core. MSDP peering addresses can
come out of either the EID or a routable address namespace. And
the choice can be made unilaterally because the ITR at the site
will determine which namespace the destination peer address is out
of by looking in the mapping database service.
PIM-SSM: In the simplest form of distribution tree building, when
PIM operates in SSM mode, a source distribution tree is built and
maintained across site boundaries. In this case, there is a small
modification to the operation of the PIM protocol (but not to any
Farinacci, et al. Expires December 22, 2011 [Page 15]
Internet-Draft LISP for Multicast Environments June 2011
message format) to support taking a Join/Prune message originated
inside of a LISP site with embedded addresses from the EID
namespace and converting them to addresses from the RLOC namespace
when the Join/Prune message crosses a site boundary. This is
similar to the requirements documented in [MNAT].
PIM-Bidir: Bidirectional PIM is typically run inside of a routing
domain, but if deployed in an inter-domain environment, one would
have to decide if the RP address of the shared-tree would be from
the EID namespace or the RLOC namespace. If the RP resides in a
site-based router, then the RP address is from the EID namespace.
If the RP resides in the core where RLOC addresses are routed,
then the RP address is from the RLOC namespace. This could be
easily distinguishable if the EID address were well-known address
allocation block from the RLOC namespace. Also, when using
Embedded-RP for RP determination [RFC3956], the format of the
group address could indicate the namespace the RP address is from.
However, refer to Section 10 for considerations core routers need
to make when using Embedded-RP IPv6 group addresses. When using
Bidir-PIM for inter-domain multicast routing, it is recommended to
use staticly configured RPs so core routers think the Bidir group
is associated with an ITR's RLOC as the RP address and site
routers think the Bidir group is associated with the site resident
RP with an EID address. With respect to DF-election in Bidir PIM,
no changes are required since all messaging and addressing is
link-local.
PIM-ASM: The ASM mode of PIM, the most popular form of PIM, is
deployed in the Internet today is by having shared-trees within a
site and using source-trees across sites. By the use of MSDP and
PIM-SSM techniques described above, we can get multicast
connectivity across LISP sites. Having said that, that means
there are no special actions required for processing (*,G) or
(S,G,R) Join/Prune messages since they all operate against the
shared-tree which is site resident. Just like with ASM, there is
no (*,G) in the core when LISP-Multicast is in use. This is also
true for the RP-mapping mechanisms Auto-RP and BSR.
Based on the protocol description above, the conclusion is that there
are no protocol message format changes, just a translation function
performed at the control-plane. This will make for an easier and
faster transition for LISP since fewer components in the network have
to change.
It should also be stated just like it is in [LISP] that no host
changes, whatsoever, are required to have a multicast source host
send multicast packets and for a multicast receiver host to receive
multicast packets.
Farinacci, et al. Expires December 22, 2011 [Page 16]
Internet-Draft LISP for Multicast Environments June 2011
8. LISP-Multicast Data-Plane Architecture
The LISP-Multicast data-plane operation conforms to the operation and
packet formats specified in [LISP]. However, encapsulating a
multicast packet from an ITR is a much simpler process. The process
is simply to copy the inner group address to the outer destination
address. And to have the ITR use its own IP address (its RLOC), and
as the source address. The process is simpler for multicast because
there is no EID-to-RLOC mapping lookup performed during packet
forwarding.
In the decapsulation case, the ETR simply removes the outer header
and performs a multicast routing table lookup on the inner header
(S-EID,G) addresses. Then the oif-list for the (S-EID,G) entry is
used to replicate the packet on site-facing interfaces leading to
multicast receiver hosts.
There is no Data-Probe logic for ETRs as there can be in the unicast
forwarding case.
8.1. ITR Forwarding Procedure
The following procedure is used by an ITR, when it receives a
multicast packet from a source inside of its site:
1. A multicast data packet sent by a host in a LISP site will have
the source address equal to the host's EID and the destination
address equal to the group address of the multicast group. It is
assumed the group information is obtained by current methods.
The same is true for a multicast receiver to obtain the source
and group address of a multicast flow.
2. When the ITR receives a multicast packet, it will have both S-EID
state and S-RLOC state stored. Since the packet was received on
a site-facing interface, the RPF lookup is based on the S-EID
state. If the RPF check succeeds, then the oif-list contains
interfaces that are site-facing and external-facing. For the
site-facing interfaces, no LISP header is prepended. For the
external-facing interfaces a LISP header is prepended. When the
ITR prepends a LISP header, it uses its own RLOC address as the
source address and copies the group address supplied by the IP
header the host built as the outer destination address.
8.1.1. Multiple RLOCs for an ITR
Typically, an ITR will have a single RLOC address but in some cases
there could be multiple RLOC addresses assigned from either the same
or different service providers. In this case when (S-RLOC,G) Join/
Farinacci, et al. Expires December 22, 2011 [Page 17]
Internet-Draft LISP for Multicast Environments June 2011
Prune messages are received for each RLOC, there is a oif-list
merging action that must take place. Therefore, when a packet is
received from a site-facing interface that matches on a (S-EID,G)
entry, the interfaces of the oif-list from all (RLOC,G) entries
joined to the ITR as well as the site-facing oif-list joined for
(S-EID,G) must be part be included in packet replication. In
addition to replicating for all types of oif-lists, each oif entry
must be tagged with the RLOC address, so encapsulation uses the outer
source address for the RLOC joined.
8.1.2. Multiple ITRs for a LISP Source Site
Note when ETRs from different multicast receiver sites receive
(S-EID,G) joins, they may select a different S-RLOC for a multicast
source site due to policy (the multicast ITR can return different
multicast priority and weight values per ETR Map-Request). In this
case, the same (S-EID,G) is being realized by different (S-RLOC,G)
state in the core. This will not result in duplicate packets because
each ITR in the multicast source site will choose their own RLOC for
the source address for encapsulated multicast traffic. The RLOC
addresses are the ones joined by remote multicast ETRs.
When different (S-EID,G) traffic is combined into a single (RLOC,G)
core distribution tree, this may cause traffic to go to a receiver
multicast site when it does not need to. This happens when one
receiver multicast site joins (S1-EID,Gi) through a core distribution
tree of (RLOC1,Gi) and another multicast receiver site joins (S2-
EID,Gi) through the same core distribution tree of (RLOC1,Gi). When
ETRs decapsulate such traffic, they should know from their local
(S-EID,G) state if the packet should be forwarded. If there is no
(S-EID,G) state that matches the inner packet header, the packet is
discarded.
8.2. ETR Forwarding Procedure
The following procedure is used by an ETR, when it receives a
multicast packet from a source outside of its site:
1. When a multicast data packet is received by an ETR on an
external-facing interface, it will do an RPF lookup on the S-RLOC
state it has stored. If the RPF check succeeds, the interfaces
from the oif-list are used for replication to interfaces that are
site-facing as well as interfaces that are external-facing (this
ETR can also be a transit multicast router for receivers outside
of its site). When the packet is to be replicated for an
external-facing interface, the LISP encapsulation header are not
stripped. When the packet is replicated for a site-facing
interface, the encapsulation header is stripped.
Farinacci, et al. Expires December 22, 2011 [Page 18]
Internet-Draft LISP for Multicast Environments June 2011
2. The packet without a LISP header is now forwarded down the
(S-EID,G) distribution tree in the receiver multicast site.
8.3. Replication Locations
Multicast packet replication can happen in the following topological
locations:
o In an IGP multicast router inside a site which operates on S-EIDs.
o In a transit multicast router inside of the core which operates on
S-RLOCs.
o At one or more ETR routers depending on the path a Join/Prune
message exits a receiver multicast site.
o At one or more ITR routers in a source multicast site depending on
what priorities are returned in a Map-Reply to receiver multicast
sites.
In the last case the source multicast site can do replication rather
than having a single exit from the site. But this only can occur
when the priorities in the Map-Reply are modified for different
receiver multicast site so that the PIM Join/Prune messages arrive at
different ITRs.
This policy technique, also used in [ALT] for unicast, is useful for
multicast to mitigate the problems of changing distribution tree
state as discussed in Section 6.
Farinacci, et al. Expires December 22, 2011 [Page 19]
Internet-Draft LISP for Multicast Environments June 2011
9. LISP-Multicast Interworking
This section will describe the multicast corollary to [INTWORK] which
describes the interworking of multicast routing among LISP and non-
LISP sites.
9.1. LISP and non-LISP Mixed Sites
Since multicast communication can involve more than two entities to
communicate together, the combinations of interworking scenarios are
more involved. However, the state maintained for distribution trees
at the sites is the same regardless of whether or not the site is
LISP enabled or not. So most of the implications are in the core
with respect to storing routable EID prefixes from either PA or PI
blocks.
Before we enumerate the multicast interworking scenarios, we must
define 3 deployment states of a site:
o A non-LISP site which will run PIM-SSM or PIM-ASM with MSDP as it
does today. The addresses for the site are globally routable.
o A site that deploys LISP for unicast routing. The addresses for
the site are not globally routable. Let's define the name for
this type of site as a uLISP site.
o A site that deploys LISP for both unicast and multicast routing.
The addresses for the site are not globally routable. Let's
define the name for this type of site as a LISP-Multicast site.
We will not consider a LISP site enabled for multicast purposes only
but do consider a uLISP site as documented in [INTWORK]. In this
section we don't discuss how a LISP site sends multicast packets when
all receiver sites are LISP-Multicast enabled; that has been
discussed in previous sections.
The following scenarios exist to make LISP-Multicast sites interwork
with non-LISP-Multicast sites:
1. A LISP site must be able to send multicast packets to receiver
sites which are a mix of non-LISP sites and uLISP sites.
2. A non-LISP site must be able to send multicast packets to
receiver sites which are a mix of non-LISP sites and uLISP sites.
3. A non-LISP site must be able to send multicast packets to
receiver sites which are a mix of LISP sites, uLISP sites, and
non-LISP sites.
Farinacci, et al. Expires December 22, 2011 [Page 20]
Internet-Draft LISP for Multicast Environments June 2011
4. A uLISP site must be able to send multicast packets to receiver
sites which are a mix of LISP sites, uLISP sites, and non-LISP
sites.
5. A LISP site must be able to send multicast packets to receiver
sites which are a mix of LISP sites, uLISP sites, and non-LISP
sites.
9.1.1. LISP Source Site to non-LISP Receiver Sites
In the first scenario, a site is LISP capable for both unicast and
multicast traffic and as such operates on EIDs. Therefore there is a
possibility that the EID prefix block is not routable in the core.
For LISP receiver multicast sites this isn't a problem but for non-
LISP or uLISP receiver multicast sites, when a PIM Join/Prune message
is received by the edge router, it has no route to propagate the
Join/Prune message out of the site. This is no different than the
unicast case that LISP-NAT in [INTWORK] solves.
LISP-NAT allows a unicast packet that exits a LISP site to get its
source address mapped to a globally routable address before the ITR
realizes that it should not encapsulate the packet destined to a non-
LISP site. For a multicast packet to leave a LISP site, distribution
tree state needs to be built so the ITR can know where to send the
packet. So the receiver multicast sites need to know about the
multicast source host by its routable address and not its EID
address. When this is the case, the routable address is the
(S-RLOC,G) state that is stored and maintained in the core routers.
It is important to note that the routable address for the host cannot
be the same as an RLOC for the site because we want the ITRs to
process a received PIM Join/Prune message from an external-facing
interface to be propagated inside of the site so the site-part of the
distribution tree is built.
Using a globally routable source address allows non-LISP and uLISP
multicast receiver to join, create, and maintain a multicast
distribution tree. However, the LISP multicast receiver site will
want to perform an EID-to-RLOC mapping table lookup when a PIM Join/
Prune message is received on a site-facing interface. It does this
because it wants to find a (S-RLOC,G) entry to Join in the core. So
we have a conflict of behavior between the two types of sites.
The solution to this problem is the same as when an ITR wants to send
a unicast packet to a destination site but needs determine if the
site is LISP capable or not. When it is not LISP capable, the ITR
does not encapsulate the packet. So for the multicast case, when ETR
receives a PIM Join/Prune message for (S-EID,G) state, it will do a
mapping table lookup on S-EID. In this case, S-EID is not in the
Farinacci, et al. Expires December 22, 2011 [Page 21]
Internet-Draft LISP for Multicast Environments June 2011
mapping database because the source multicast site is using a
routable address and not an EID prefix address. So the ETR knows to
simply propagate the PIM Join/Prune message to a external-facing
interface without converting the (S-EID,G) because it is an (S,G)
where S is routable and reachable via core routing tables.
Now that the multicast distribution tree is built and maintained from
any non-LISP or uLISP receiver multicast site, the way packet
forwarding model is performed can be explained.
Since the ITR in the source multicast site has never received a
unicast encapsulated PIM Join/Prune message from any ETR in a
receiver multicast site, it knows there are no LISP-Multicast
receiver sites. Therefore, there is no need for the ITR to
encapsulate data. Since it will know a priori (via configuration)
that its site's EIDs are not routable (and not registered to the
mapping database system), it assumes that the multicast packets from
the source host are sent by a routable address. That is, it is the
responsibility of the multicast source host's system administrator to
ensure that the source host sends multicast traffic using a routable
source address. When this happens, the ITR acts simply as a router
and forwards the multicast packet like an ordinary multicast router.
There is an alternative to using a LISP-NAT scheme just like there is
for unicast [INTWORK] forwarding by using Proxy Tunnel Routers
(PxTRs). This can work the same way for multicast routing as well,
but the difference is that non-LISP and uLISP sites will send PIM
Join/Prune messages for (S-EID,G) which make their way in the core to
multicast PxTRs. Let's call this use of a PxTR as a "Multicast
Proxy-ETR" (or mPETR). Since the mPETRs advertise very coarse EID
prefixes, they draw the PIM Join/Prune control traffic making them
the target of the distribution tree. To get multicast packets from
the LISP source multicast sites, the tree needs to be built on the
path from the mPETR to the LISP source multicast site. To make this
happen the mPETR acts as a "Proxy ETR" (where in unicast it acts as a
"Proxy ITR", or an uPITR [INTWORK]).
The existence of mPETRs in the core allows source multicast site ITRs
to encapsulate multicast packets according to (S-RLOC,G) state. The
(S-RLOC,G) state is built from the mPETRs to the multicast ITRs. The
encapsulated multicast packets are decapsulated by mPETRs and then
forwarded according to (S-EID,G) state. The (S-EID,G) state is built
from the non-LISP and uLISP receiver multicast sites to the mPETRs.
9.1.2. Non-LISP Source Site to non-LISP Receiver Sites
Clearly non-LISP multicast sites can send multicast packets to non-
LISP receiver multicast sites. That is what they do today. However,
Farinacci, et al. Expires December 22, 2011 [Page 22]
Internet-Draft LISP for Multicast Environments June 2011
discussion is required to show how non-LISP multicast sites send
multicast packets to uLISP receiver multicast sites.
Since uLISP receiver multicast sites are not targets of any (S,G)
state, they simply send (S,G) PIM Join/Prune messages toward the non-
LISP source multicast site. Since the source multicast site, in this
case has not been upgraded to LISP, all multicast source host
addresses are routable. So this case is simplified to where a uLISP
receiver multicast site looks to the source multicast site as a non-
LISP receiver multicast site.
9.1.3. Non-LISP Source Site to Any Receiver Site
When a non-LISP source multicast site has receivers in either a non-
LISP/uLISP site or a LISP site, one needs to decide how the LISP
receiver multicast site will attach to the distribution tree. We
know from Section 9.1.2 that non-LISP and uLISP receiver multicast
sites can join the distribution tree, but a LISP receiver multicast
site ETR will need to know if the source address of the multicast
source host is routable or not. We showed in Section 9.1.1 that an
ETR, before it sends a PIM Join/Prune message on an external-facing
interface, does a EID-to-RLOC mapping lookup to determine if it
should convert the (S,G) state from a PIM Join/Prune message received
on a site-facing interface to a (S-RLOC,G). If the lookup fails, the
ETR can conclude the source multicast site is a non-LISP site so it
simply forwards the Join/Prune message (it also doesn't need to send
a unicast encapsulated Join/Prune message because there is no ITR in
a non-LISP site and there is namespace continuity between the ETR and
source).
For a non-LISP source multicast site, (S-EID,G) state could be
limited to the edges of the network with the use of multicast proxy-
ITRs (mPITRs). The mPITRs can take native, unencapsulated multicast
packets from non-LISP source multicast and uLISP sites and
encapsulate them to ETRs in receiver multicast sites or to mPETRs
that can decapsulate for non-LISP receiver multicast or uLISP sites.
The mPITRs are responsible for sending (S-EID,G) joins to the non-
LISP source multicast site. To connect the distribution trees
together, multicast ETRs will need to be configured with the mPITR's
RLOC addresses so they can send both (S-RLOC,G) joins to build a
distribution tree to the mPITR as well as for sending unicast joins
to mPITRs so they can propogate (S-EID,G) joins into source multicast
sites. The use of mPITRs is undergoing more study and is work in
progress.
Farinacci, et al. Expires December 22, 2011 [Page 23]
Internet-Draft LISP for Multicast Environments June 2011
9.1.4. Unicast LISP Source Site to Any Receiver Sites
In the last section, it was explained how an ETR in a multicast
receiver site can determine if a source multicast site is LISP-
enabled by looking into the mapping database. When the source
multicast site is a uLISP site, it is LISP enabled but the ITR, by
definition is not capable of doing multicast encapsulation. So for
the purposes of multicast routing, the uLISP source multicast site is
treated as non-LISP source multicast site.
Non-LISP receiver multicast sites can join distribution trees to a
uLISP source multicast site since the source site behaves, from a
forwarding perspective, as a non-LISP source site. This is also the
case for a uLISP receiver multicast site since the ETR does not have
multicast functionality built-in or enabled.
Special considerations are required for LISP receiver multicast sites
since they think the source multicast site is LISP capable, the ETR
cannot know if ITR is LISP-Multicast capable. To solve this problem,
each mapping database entry will have a multicast 2-tuple (Mpriority,
Mweight) per RLOC. When the Mpriority is set to 255, the site is
considered not multicast capable. So an ETR in a LISP receiver
multicast site can distinguish whether a LISP source multicast site
is LISP-Multicast site from a uLISP site.
9.1.5. LISP Source Site to Any Receiver Sites
When a LISP source multicast site has receivers in LISP, non-LISP,
and uLISP receiver multicast sites, it has a conflict about how it
sends multicast packets. The ITR can either encapsulate or natively
forward multicast packets. Since the receiver multicast sites are
heterogeneous in their behavior, one packet forwarding mechanism
cannot satisfy both. However, if a LISP receiver multicast site acts
like a uLISP site then it could receive packets like a non-LISP
receiver multicast site making all receiver multicast sites have
homogeneous behavior. However, this poses the following issues:
o LISP-NAT techniques with routable addresses would be required in
all cases.
o Or alternatively, mPETR deployment would be required forcing
coarse EID prefix advertisement in the core.
o But what is most disturbing is that when all sites that
participate are LISP-Multicast sites but then a non-LISP or uLISP
site joins the distribution tree, then the existing joined LISP
receiver multicast sites would have to change their behavior.
This would create too much dynamic tree-building churn to be a
Farinacci, et al. Expires December 22, 2011 [Page 24]
Internet-Draft LISP for Multicast Environments June 2011
viable alternative.
So the solution space options are:
1. Make the LISP ITR in the source multicast site send two packets,
one that is encapsulated with (S-RLOC,G) to reach LISP receiver
multicast sites and another that is not encapsulated with
(S-EID,G) to reach non-LISP and uLISP receiver multicast sites.
2. Make the LISP ITR always encapsulate packets with (S-RLOC,G) to
reach LISP-Multicast sites and to reach mPETRs that can
decapsulate and forward (S-EID,G) packets to non-LISP and uLISP
receiver multicast sites.
9.2. LISP Sites with Mixed Address Families
A LISP database mapping entry that describes the locator-set,
Mpriority and Mweight per locator address (RLOC), for an EID prefix
associated with a site could have RLOC addresses in either IPv4 or
IPv6 format. When a mapping entry has a mix of RLOC formatted
addresses, it is an implicit advertisement by the site that it is a
dual-stack site. That is, the site can receive IPv4 or IPv6 unicast
packets.
To distinguish if the site can receive dual-stack unicast packets as
well as dual-stack multicast packets, the Mpriority value setting
will be relative to an IPv4 or IPv6 RLOC See [LISP] for packet format
details.
If you consider the combinations of LISP, non-LISP, and uLISP sites
sharing the same distribution tree and considering the capabilities
of supporting IPv4, IPv6, or dual-stack, the number of total
combinations grows beyond comprehension.
Using some combinatorial math, we have the following profiles of a
site and the combinations that can occur:
1. LISP-Multicast IPv4 Site
2. LISP-Multicast IPv6 Site
3. LISP-Multicast Dual-Stack Site
4. uLISP IPv4 Site
5. uLISP IPv6 Site
Farinacci, et al. Expires December 22, 2011 [Page 25]
Internet-Draft LISP for Multicast Environments June 2011
6. uLISP Dual-Stack Site
7. non-LISP IPv4 Site
8. non-LISP IPv6 Site
9. non-LISP Dual-Stack Site
Lets define (m n) = m!/(n!*(m-n)!), pronounced "m choose n" to
illustrate some combinatorial math below.
When 1 site talks to another site, the combinatorial is (9 2), when 1
site talks to another 2 sites, the combinatorial is (9 3). If sum
this up to (9 9), we have:
(9 2) + (9 3) + (9 4) + (9 5) + (9 6) + (9 7) + (9 8) + (9 9) =
36 + 84 + 126 + 126 + 84 + 36 + 9 + 1
Which results in the total number of cases to be considered at 502.
This combinatorial gets even worse when you consider a site using one
address family inside of the site and the xTRs use the other address
family (as in using IPv4 EIDs with IPv6 RLOCs or IPv6 EIDs with IPv4
RLOCs).
To rationalize this combinatorial nightmare, there are some
guidelines which need to be put in place:
o Each distribution tree shared between sites will either be an IPv4
distribution tree or an IPv6 distribution tree. Therefore, we can
avoid head-end replication by building and sending packets on each
address family based distribution tree. Even though there might
be an urge to do multicast packet translation from one address
family format to the other, it is a non-viable over-complicated
urge. Multicast ITRs will only encapsulate packets where the
inner and outer headers are from the same address family.
o All LISP sites on a multicast distribution tree must share a
common address family which is determined by the source site's
locator-set in its LISP database mapping entry. All receiver
multicast sites will use the best RLOC priority controlled by the
source multicast site. This is true when the source site is
either LISP-Multicast or uLISP capable. This means that priority-
based policy modification is prohibited. When a receiver
multicast site ETR receives a (S-EID,G) join, it must select a
S-RLOC for the same address family as S-EID.
Farinacci, et al. Expires December 22, 2011 [Page 26]
Internet-Draft LISP for Multicast Environments June 2011
o A mixed multicast locator-set with the best multicast priority
values MUST NOT be configured on multicast ITRs. A mixed locator-
set can exist (for unicast use), but the multicast priorities MUST
be the set for the same address family locators.
o When the source site is not LISP capable, it is up to how
receivers find the source and group information for a multicast
flow. That mechanism decides the address family for the flow.
9.3. Making a Multicast Interworking Decision
This Multicast Interworking section has shown all combinations of
multicast connectivity that could occur. As you might have already
concluded, this can be quite complicated and if the design is too
ambitious, the dynamics of the protocol could cause a lot of
instability.
The trade-off decisions are hard to make and we want the same single
solution to work for both IPv4 and IPv6 multicast. It is imperative
to have an incrementally deployable solution for all of IPv4 unicast
and multicast and IPv6 unicast and multicast while minimizing (or
eliminating) both unicast and multicast EID namespace state.
Therefore the design decision to go with uPITRs [INTWORK] for unicast
routing and mPETRs for multicast routing seems to be the sweet spot
in the solution space so we can optimize state requirements and avoid
head-end data replication at ITRs.
Farinacci, et al. Expires December 22, 2011 [Page 27]
Internet-Draft LISP for Multicast Environments June 2011
10. Considerations when RP Addresses are Embedded in Group Addresses
When ASM and PIM-Bidir is used in an IPv6 inter-domain environment, a
technique exists to embed the unicast address of an RP in a IPv6
group address [RFC3956]. When routers in end sites process a PIM
Join/Prune message which contain an embedded-RP group address, they
extract the RP address from the group address and treat it from the
EID namespace. However, core routers do not have state for the EID
namespace, need to extract an RP address from the RLOC namespace.
Therefore, it is the responsibility of ETRs in multicast receiver
sites to map the group address into a group address where the
embedded-RP address is from the RLOC namespace. The mapped RP-
address is obtained from a EID-to-RLOC mapping database lookup. The
ETR will also send a unicast (*,G) Join/Prune message to the ITR so
the branch of the distribution tree from the source site resident RP
to the ITR is created.
This technique is no different than the techniques described in this
specification for translating (S,G) state and propagating Join/Prune
messages into the core. The only difference is that the (*,G) state
in Join/Prune messages are mapped because they contain unicast
addresses encoded in an Embedded-RP group address.
Farinacci, et al. Expires December 22, 2011 [Page 28]
Internet-Draft LISP for Multicast Environments June 2011
11. Taking Advantage of Upgrades in the Core
If the core routers are upgraded to support [RPFV] and [RFC5496],
then we can pass EID specific data through the core without,
possibly, having to store the state in the core.
By doing this we can eliminate the ETR from unicast encapsulating PIM
Join/Prune messages to the source site's ITR.
However, this solution is restricted to a small set of workable cases
which would not be good for general use of LISP-Multicast. In
addition due to slow convergence properties, it is not being
recommended for LISP-Multicast.
Farinacci, et al. Expires December 22, 2011 [Page 29]
Internet-Draft LISP for Multicast Environments June 2011
12. Mtrace Considerations
Mtrace functionality must be consistent with unicast traceroute
functionality where all hops from multicast receiver to multicast
source are visible.
The design for mtrace for use in LISP-Multicast environments is to be
determined but should build upon the mtrace version 2 specified in
[MTRACE].
Farinacci, et al. Expires December 22, 2011 [Page 30]
Internet-Draft LISP for Multicast Environments June 2011
13. Security Considerations
Refer to the [LISP] specification.
Farinacci, et al. Expires December 22, 2011 [Page 31]
Internet-Draft LISP for Multicast Environments June 2011
14. Acknowledgments
The authors would like to gratefully acknowledge the people who have
contributed discussion, ideas, and commentary to the making of this
proposal and specification. People who provided expert review were
Scott Brim, Greg Shepherd, and Dave Oran. Other commentary from
discussions at Summer 2008 Dublin IETF were Toerless Eckert and
Ijsbrand Wijnands.
We would also like to thank the MBONED working group for constructive
and civil verbal feedback when this draft was presented at the Fall
2008 IETF in Minneapolis. In particular, good commentary came from
Tom Pusateri, Steve Casner, Marshall Eubanks, Dimitri Papadimitriou,
Ron Bonica, Lenny Guardino, Alia Atlas, and Jesus Arango.
An expert review of this specification was done by Yiqun Cai and
Liming Wei. We thank them for their detailed comments.
This work originated in the Routing Research Group (RRG) of the IRTF.
The individual submission [MLISP] was converted into this IETF LISP
working group draft.
Farinacci, et al. Expires December 22, 2011 [Page 32]
Internet-Draft LISP for Multicast Environments June 2011
15. References
15.1. Normative References
[LISP] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis,
"Locator/ID Separation Protocol (LISP)",
draft-ietf-lisp-13.txt (work in progress), June 2011.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3618] Fenner, B. and D. Meyer, "Multicast Source Discovery
Protocol (MSDP)", RFC 3618, October 2003.
[RFC3956] Savola, P. and B. Haberman, "Embedding the Rendezvous
Point (RP) Address in an IPv6 Multicast Address",
RFC 3956, November 2004.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601, August 2006.
[RFC4604] Holbrook, H., Cain, B., and B. Haberman, "Using Internet
Group Management Protocol Version 3 (IGMPv3) and Multicast
Listener Discovery Protocol Version 2 (MLDv2) for Source-
Specific Multicast", RFC 4604, August 2006.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for
IP", RFC 4607, August 2006.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
January 2007.
[RFC5015] Handley, M., Kouvelas, I., Speakman, T., and L. Vicisano,
"Bidirectional Protocol Independent Multicast (BIDIR-
PIM)", RFC 5015, October 2007.
[RFC5496] Wijnands, IJ., Boers, A., and E. Rosen, "The Reverse Path
Forwarding (RPF) Vector TLV", RFC 5496, March 2009.
15.2. Informative References
[ALT] Farinacci, D., Fuller, V., and D. Meyer, "LISP Alternative
Topology (LISP-ALT)", draft-ietf-lisp-alt-06.txt (work in
progress), March 2011.
[INTWORK] Lewis, D., Meyer, D., and D. Farinacci, "Interworking LISP
Farinacci, et al. Expires December 22, 2011 [Page 33]
Internet-Draft LISP for Multicast Environments June 2011
with IPv4 and IPv6", draft-ietf-lisp-interworking-02.txt
(work in progress), March 2011.
[MLISP] Farinacci, D., Meyer, D., Zwiebel, J., and S. Venaas,
"LISP for Multicast Environments",
draft-farinacci-lisp-multicast-01.txt (work in progress),
November 2008.
[MNAT] Wing, D. and T. Eckert, "Multicast Requirements for a
Network Address (and port) Translator (NAT)",
draft-ietf-behave-multicast-07.txt (work in progress),
June 2007.
[MTRACE] Asaeda, H., Jinmei, T., Fenner, W., and S. Casner, "Mtrace
Version 2: Traceroute Facility for IP Multicast",
draft-ietf-mboned-mtrace-v2-03.txt (work in progress),
March 2009.
[RPFV] Wijnands, IJ., Boers, A., and E. Rosen, "The RPF Vector
TLV", draft-ietf-pim-rpf-vector-06.txt (work in progress),
February 2008.
Farinacci, et al. Expires December 22, 2011 [Page 34]
Internet-Draft LISP for Multicast Environments June 2011
Appendix A. Document Change Log
A.1. Changes to draft-ietf-lisp-multicast-06.txt
o Posted June 2011 to complete working group last call.
o Added paragraph to section 8.1.2 based on Jesus comment about
making it more clear what happens when two (S-EID,G) trees use the
same (RLOC,G) tree.
o Make more references to [INTWORK] when mentioning uPITRs and
uPETRs.
o Made many changes based on editorial and wordsmithing comments
from Alia.
A.2. Changes to draft-ietf-lisp-multicast-05.txt
o Posted April 2011 to reset expiration timer.
o Updated references.
A.3. Changes to draft-ietf-lisp-multicast-04.txt
o Posted October 2010 to reset expiration timer.
o Updated references.
A.4. Changes to draft-ietf-lisp-multicast-03.txt
o Posted April 2010.
o Added section 8.1.2 to address Joel Halpern's comment about
receiver sites joining the same source site via 2 different RLOCs,
each being a separate ITR.
o Change all occurences of "mPTR" to "mPETR" to become more
consistent with uPITRs and uPETRs described in [INTWORK]. That
is, an mPETR is a LISP multicast router that decapsulates
multicast packets that are encapsulated to it by ITRs in multicast
source sites.
o Add clarifications in section 9 about how homogeneous multicast
encapsulation should occur. As well as describing in this
section, how to deal with mixed-locator sets to avoid
heterogeneous encapsulation.
Farinacci, et al. Expires December 22, 2011 [Page 35]
Internet-Draft LISP for Multicast Environments June 2011
o Introduce concept of mPITRs to help reduce (S-EID,G) to the edges
of LISP global multicast network.
A.5. Changes to draft-ietf-lisp-multicast-02.txt
o Posted September 2009.
o Added Document Change Log appendix.
o Specify that the LISP Encapsulated Control Message be used for
unicasting PIM Join/Prune messages from ETRs to ITRs.
A.6. Changes to draft-ietf-lisp-multicast-01.txt
o Posted November 2008.
o Specified that PIM Join/Prune unicast messages that get sent from
ETRs to ITRs of a source multicast site get LISP encapsulated in
destination UDP port 4342.
o Add multiple RLOCs per ITR per Yiqun's comments.
o Indicate how static RPs can be used when LISP is run using Bidir-
PIM in the core.
o Editorial changes per Liming comments.
o Add Mttrace Considersations section.
A.7. Changes to draft-ietf-lisp-multicast-00.txt
o Posted April 2008.
o Renamed from draft-farinacci-lisp-multicast-01.txt.
Farinacci, et al. Expires December 22, 2011 [Page 36]
Internet-Draft LISP for Multicast Environments June 2011
Authors' Addresses
Dino Farinacci
cisco Systems
Tasman Drive
San Jose, CA
USA
Email: dino@cisco.com
Dave Meyer
cisco Systems
Tasman Drive
San Jose, CA
USA
Email: dmm@cisco.com
John Zwiebel
cisco Systems
Tasman Drive
San Jose, CA
USA
Email: jzwiebel@cisco.com
Stig Venaas
cisco Systems
Tasman Drive
San Jose, CA
USA
Email: stig@cisco.com
Farinacci, et al. Expires December 22, 2011 [Page 37]
