LISP Working Group S. Barkai
Internet-Draft B. Fernandez-Ruiz
Intended status: Informational R. Tamir
Expires: February 16,2023 Nexar Inc.
A. Rodriguez-Natal
F. Maino
Cisco Systems
A. Cabellos-Aparicio
J. Paillisse Vilanova
Technical University of Catalonia
D. Farinacci
lispers.net
October 1, 2022
Network-Hexagons:Geolocation Mobility Edge Network Based On H3 and LISP
draft-ietf-lisp-nexagon-40
Abstract
This document uses virtual layer3 routing and geospatial addressing
based on a hierarchical grid forming a Geolocation mobility-edge
network. When vehicles with AI cameras detect objects of interest
on the road, they use their GPS to calculate their high-resolution
grid-tile position. Then they use this tile to calculate the
high-resolution tile of the detection. A low-resolution tile which
contains the detection-tile identifies a network-addressable object.
The object tile-ID is used as basis for IPv6 endpoint identifier(EID).
Geospatial EIDs are queue-destination and channel-source of objects.
Geolocation objects consolidate detections form all vehicles in a
given area. Geolocation objects based on EID queues and channels are
network portable via the Locator/ID Separation Protocol (LISP).
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on February 16,2023.
Barkai, et al. Expires February 16,2023 [Page 1]
Internet-Draft LISP October 2022
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Definition of Terms . . . . . . . . . . . . . . . . . . . . . 5
3. Deployment Assumptions . . . . . . . . . . . . . . . . . . . 7
4. Mobility Clients-Services Networking . . . . . . . . . . . . 8
5. Mobility Unicast and Multicast . . . . . . . . . . . . . . . 9
6. Security Considerations . . . . . . . . . . . . . . . . . . . 15
7. Privacy Considerations . . . . . . . . . . . . . . . . . . . 15
8. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 16
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 17
10. Normative References . . . . . . . . . . . . . . . . . . . . 29
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 30
1. Introduction
This document uses virtual layer3 routing and geospatial addressing
based on a hierarchical grid forming a Geolocation mobility-edge
network. When vehicles with AI cameras detect objects of interest
on the road, they use their GPS to calculate their high-resolution
grid-tile position. Then they use this tile to calculate the
high-resolution tile of the detection. A low-resolution tile which
contains the detection-tile identifies a network-addressable object.
The object tile-ID is used as basis for IPv6 endpoint identifier(EID).
Geospatial EIDs are queue-destination and channel-source of objects.
Geolocation objects consolidate detections form all vehicles in a
given area. Geolocation objects based on EID queues and channels are
network portable via the Locator/ID Separation Protocol (LISP).
Network addressable hexagonal grid objects (nexagons) encapsulate
geolocation processing are delegated dynamically to compute locations
per road activity: vehicle uploads and client subscriptions. Dynamics
of vehicles and clients causes key-issues resolved by LISP:
- Dynamic allocation and coherency of services IPs cached by clients
- Context-switching between Geolocation Services IPs while driving
- Geo-privacy and tracking of clients interacting with services
- Subscription continuity when switching IP Anchors while driving
Barkai, et al. Expires February 16,2023 [Page 2]
Internet-Draft LISP October 2022
These key-issues are resolved using LISP mapped EID virtualization:
- Addresses virtualization of the communicating clients and services
- Algorithmic service-addressing based on geospatial grid identifiers
- Algorithmic client-addressing based on an authorization procedure
Geolocation virtual addressing for queues and for channels helps solve
services objects portability. Because other than queues and channels,
functional stacks are pervasive and objects-states quickly regenerate.
Portability solves dynamic allocation and reduces coherency issues.
As for client side EIDs, these enable subscription continuity and geo-
privacy. The resulting elastic allocation uses EID algorithmic context
switching, maintain subscription continuity and IP geo-privacy.
___
/ \
Addressable >> States >> Addressable
Upload Queues \ ___ / Channels
/\ Functions() \/
Figure 1: Geolocation schematics: queues, channels, states, functions
To summarize Address virtualization based on LISP EIDs:
- EID addressing of Geolocation upload queues by H3 identifiers
- EID addressing of detection channels, H3 ID sources and topics
- EID addressing of mobility clients, assigned and also renewed
Barkai, et al. Expires February 16,2023 [Page 3]
Internet-Draft LISP October 2022
Note 1: The breakdown of Geolocations Services to objects is done
based on geospatial grid lines known to both mobility clients and
Geolocation Services. We use H3 [H3] hierarchical hexagonal grid
because of its clear tile adjacency properties. Each grid-tile
in each resolution has a unique 64bit identifier (HID). HIDs are
mapped to EIDs algorithmically. In addition to objects, the same grid
at higher resolution (smaller tiles) is used to localize detections.
We refer to h3.rB as the lower resolution object big tile, and h3.rS
as the detection location, higher resolution small tile.
Mappings: GPS => h3.rS => H3.rB => EID are therefore algorithmic.
Sizeof (h3.rB) / Sizeof (h3.rS) x density-factor / MTU ~ number of
messages needed to convey object state snapshot of small-tiles in it.
Off-Peak object Allocation
Packed on less compute
_ _ _ _
/ \/ \ / \/ \ ----
\_/\_/ \_/\_/ ---- Peak object Geolocation Allocation
/ \/ \ / \/ \ ---- Geospatial objects spread on more compute
\_/\_/ \_/\_/ ---- _ _ _ _ _ _ _ _
/ \/ \ / \/ \ ---- / \/ \ / \/ \ / \/ \ / \/ \ ----
\_/\_/ \_/\_/ ---- \_/\_/ \_/\_/ \_/\_/ \_/\_/ ----
/ \/ \ / \/ \ ---- / \/ \ / \/ \ / \/ \ / \/ \ ----
\_/\_/ \_/\_/ ---- \_/\_/ \_/\_/ \_/\_/ \_/\_/ ----
^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^
Site Site Standby Site Site Site Site Standby
Figure 2: Geolocation dynamic allocation per geospatial activity
Note 2: LISP solution for address virtualization forms an application
network. In order for clients and services to use it there needs to be
a formal provisioning step. For the clients this step will require
Authentication Authorization and Accounting (AAA) procedure by which
clients are assigned and renew EIDs and XTRs to be used to interact
with services. This process may be done in various vendor specific
methods, or multivendor AAA service. AAA procedure is described as
a life-cycle example.
Note 3: In order to make the notion of geospatial detection concrete,
we add to the 64bit HID of "where" is a detection, 64bit of "what" is
the detection or situation. These 64 bits are detailed in a bit-mask
based on a taxonomy defined by Berkeley Deep Drive [BDD]. It is meant
as a baseline that can be extended or overridden depending on need.
Barkai, et al. Expires February 16,2023 [Page 4]
Internet-Draft LISP October 2022
2. Definition of Terms
Based on [I-D.ietf-lisp-rfc6830bis][I-D.ietf-lisp-rfc6833bis]
H3ServiceEID: Is an EID addressable Geolocation Service object.
It is a designated destination for geospatial detections,
and an (S,G) source of multicast of themed detection channels.
It has a light-weight LISP protocol stack to tunnel packets
via ServerXTR. The EID is IPv6 and contains HID in the lower bits.
ServerXTR: Is a data-plane only LISP protocol stack implementation, it
is co-located with H3ServiceEID process. ServerXTR encapsulates and
decapsulates packets to and from EdgeRTRs.
MobilityClient: Is an application that may be a part of a vehicle
system, part of a navigation application, gov-muni application etc.
It has light-weight LISP data-plane stack to packets via ClientXTR.
MobilityClientEID: Is the IPv6 EID used by the Mobility Clients.
The destination of such packets are H3ServiceEIDs. The EID format
is assigned as part of the MobilityClient mobility-network AAA.
ClientXTR: Is a data-plane only LISP protocol stack implementation
co-located with the Mobility Client application. It encapsulates
and decapsulates packets to and from EdgeRTRs.
EdgeRTR: EdgeRTR network connects MobilityClients to H3ServiceEIDs.
EdgeRTRs manage MobilityClients multicast registrations [RFC8378].
EdgeRTRs aggregate MobilityClients/H3Services using tunnels to
facilitate hosting-providers and mobile-providers in accessing the
LISP based Geolocation mobility-network.
EdgeRTRs decapsulate packets from ClientXTRs and ServerXTRs,
and re-encapsulates packets to clients and servers.
EdgeRTRs glean H3ServiceEIDs and MobilityClient EIDs when
they decapsulates packets. EdgeRTRs store H3ServiceEIDs and route-
locations (RLOC) using map-caches. Mappings are registered to the
LISP mapping system [I-D.ietf-lisp-rfc6833bis]. Mappings may be
provisioned when H3Services are assigned EdgeRTRs. EdgeRTRs do not
register MobilityClients' EIDs.
Enterprises may provide their own EdgeRTRs to protect geo-privacy.
Barkai, et al. Expires February 16,2023 [Page 5]
Internet-Draft LISP October 2022
h3.rB routed-objects grid tiles
___ ___
H3ServiceEIDs ___ / \ H3ServiceEIDs ___ / \
___ / | h3.rB | ___ / | h3.rB |
/ | h3.rB \ ___ / / | h3.rB \ ___ /
| h3.rB \ ___ / sXTR | h3.rB \ ___ / sXTR
\ ___ / sXTR || \ ___ / sXTR ||
sXTR || || sXTR || ||
|| || || || || ||
|| || || || || ||
= = = = = = EdgeRTR EdgeRTR = = = = =
|| (( () )) ||
( Geolocation )
( Mobility Network )
( Based on LISP )
( || (( (()) () || )
|| ||
= = = = = = = = = = = = = =
|| ||
EdgeRTR EdgeRTR
.. .. .. ..
.. .. .. ..
((((|)))) ((((|)))) ((((|)))) ((((|))))
/|\ RAN /|\ /|\ RAN /|\
|| ||
|| ||
Uploads Upstream ||
Channels Downstream ||
|| ___ ___ ___ ||
|| << movment << / \/ \/ \<<cXTR::MobilityClientB
|| - - - - - - - - h3.rS h3.rS h3.rS - - - - - - - - - - - -
MobilityClientA::cXTR >> \ ___ /\ ___ / >> movement >> .......
Figure 3: Geolocation clients and services interaction layout
Figure 3 above describes:
- MobilityClientA detections used by MobilityClientB, and vice versa
- Clients: share information only via Geolocation Services
- ClientXTR (cXTR):encapsulates packets over access network to EdgeRTR
- ServerXTR (sXTR):encapsulates packets over edge network to EdgeRTR
- Uploads: routed to appropriate Geolocation Service by EdgeRTRs
- Channels: originate from Geolocation Services replicated by EdgeRTRs
Barkai, et al. Expires February 16,2023 [Page 6]
Internet-Draft LISP October 2022
3. Deployment Assumptions
I. We assume detections can be localized to h3.rS tiles and can be
enumerated. Compact 64bit detection enumeration format:
0 1 2 3 4 5 6 7
+-------+-------+-------+-------+-------+-------+-------+-------+
|-0-|-1-|-2-|-3-|-4-|-5-|-6-|-7-|-8-|-9-|-A-|-B-|-C-|-D-|-E-|-F-|
|012301230123012301230123 Index 01230123012301230123012301230123
+---------------------------------------------------------------+
Figure 4: Nibble based compact representation of tile state
Detections are in 16 fields x 16 enumerations. Nibbles are named using
hexadecimal index according to the position where the most significant
nibble has index 0. Values based on [BDD] are defined in section 8.
II. Authorization of MobilityClients to mobility-network is renewed
while driving. DNS/AAA procedure described bellow can be used as an
example to obtain EIDs/EdgeRTRs and for enabling use of the network.
Diameter [RFC6733] based AAA can be used to accommodate many types
of mobility clients in a rich eco-system: vehicle systems, driving
and navigation applications, smart-city and consumer applications.
Example procedure for ClientXTRs to use the mobility-network:
1) obtain the address of the mobility-network AAA using DNS
2) obtain MobilityClientEIDs and EdgeRTRs from AAA procedure
3) renewed periodically from AAA while using the network
MobilityClient DomainNameServer AAA Server MobilityEdgeRTR
| | | |
| lookup AAA Server | | |
|------------------->| | |
|<-------------------| | |
| AAA Server IP | | |
| | | |
| Client identifier and credentials | |
|--------------------------------------->| |
| | |Provision Client EID|
| | |------------------->|
| | |<-------------------|
| | | Ack Provisioed EID |
| Send ClientEID,EdgeRTR RLOC | |
|<---------------------------------------| |
. .
. Use The H3-LISP Geolocation Mobility Network .
. .
|<----------------------------------------------------------->|
. .
. Renew AAA ClientEID and EdgeRTR provisioning .
Figure 5: Example exchange for mobility-network usage
Barkai, et al. Expires February 16,2023 [Page 7]
Internet-Draft LISP October 2022
4. Mobility Clients-Services Networking
The mobility-network functions as a standard LISP overlay.
The overlay delivers unicast and multicast packets across:
Data-plane XTRs are used in the stack of each mobility client/server.
ClientXTRs and ServerXTRs are associated with EdgeRTRs.
This structure allows for MobilityClients to "show up" at any of
mobility-network location behind any network provider or network
address translation domain. It allows for any H3ServiceEID to be
instantiated, delegated, or failed-over to any compute location.
In this specification we assume semi-random association between
ClientXTRs and EdgeRTRs assigned by the AAA procedure. We assume in
any given metro area a pool of EdgeRTRs distribute the Mobility
Clients load. We assume EdgeRTRs are topologically equivalent.
EdgeRTRs use LISP to encapsulate traffic to and from other EdgeRTRs.
There may be more than one ClientEID in the same process using the
same ClientXTR. For example layers on base-map or heads-up display.
Such vendor specific multiplexing implementation is unspecified he
MobilityClient == ClientXTR ClientXTR == MobilityClient
(Encryption and Decryption) || || (Encryption and Decryption)
|| ||
EdgeRTR X EdgeRTR
|| ||
(Encryption and Decryption) || || (Encryption and Decryption)
H3ServiceEID == ServerXTR ServerXTR == H3ServiceEID
Figure 6: LISP network connecting MobilityClients and H3ServiceEIDs
The following Lisp Canonical Address Format (LCAF) [RFC8060] is used
to encode H3-IDs into IPv6 address:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AFI = 16387 | Rsvd1 | Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Type = 4 H3-ID | Rsvd2 | Length = 64 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| HID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| HID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: LCAF for encoding HIDs in H3ServiceEIDs
Barkai, et al. Expires February 16,2023 [Page 8]
Internet-Draft LISP October 2022
5. Mobility Unicast and Multicast
The day in a life of unicast detection upload:
1. A client detects condition of interest using AI camera
2. The client uses its GPS to establish its h3.rS location
3. It then estimates the h3.rS location of the detection
4. Detection h3.rS center is used to calculate h3.rB => H3ServerEID
5. Client sends (encrypted) location-detection via its ClientXTR
Outer Header src/dest: ClientXTR RLOC, EdgeRTR RLOC
Inner Header src/dest: ClientEID, H3ServiceEID
6. EdgeRTR gleans and caches ClientEID and ClientXTR RLOC
7. EdgeRTR resolves RLOC of remote EdgeRTR, and re-encapsulates:
Outer Header src/dest: EdgeRTR RLOC, remote EdgeRTR RLOC
Inner Header src/dest: ClientEID, H3ServiceEID
8. Remote EdgeRTR lookups H3ServerEID ServerXTR RLOC, re-encapsulates:
Outer Header src/dest: EdgeRTR RLOC, ServerXTR RLOC
Inner Header src/dest: ClientEID, H3ServiceEID
9. ServerXTR delivers ClientEID message to H3ServiceEID
The detection message headers consist of the following fields:
- Outer headers size = 40 (IPv6) + 8 (UDP) + 8 (LISP) = 56
- Inner headers size = 40 (IPv6) + 8 (UDP) + 4 (Nexagon Header) = 52
- 1500 (MTU) - 56 - 52 = 1392 bytes of effective payload size
Nexagon Header allows for key-value (kv) tuples or value-key,key
..(vkkk) using the same formats of key and value outlined bellow
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
| Type |gzip | Reserved | Pair Count = X|Nexagon
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 8: Nexagon header format
Nexagon Header Type 0:reserved (*)
Type 1:key-value, key-value.. 1392 / (8 + 8) = 87 pairs
Type 2:value, key,key,key.. (1392 - 8) / 8 = 173 h3.rS IDs
Type 3-255: unassigned
Nexagon Header GZIP field: 0x000 no compression, or (**) GZIP version.
Nexagon Header Reserved bits
Nexagon Header key and value count (in any format kv or vkkk)
(*) Reserved fields are specified as being set to 0 on transmission,
ignored when received.
(**) GZIP refers to entire kv or vkkk payload and major GZIP version,
packets with unsupported GZIP version are dropped
Barkai, et al. Expires February 16,2023 [Page 9]
Internet-Draft LISP October 2022
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
|Version| Traffic Class | Flow Label | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| Payload Length | Next Header | Hop Limit | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| | |
+ + |
| | |
+ Source MobilityClientEID + |
| | IPv6
+ + |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| | |
+ + |
| | |
+ Dest H3ServiceEID + |
| | |
+ + |
| | /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = xxxx | Dest Port = xxxx | \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ UDP
| UDP Length | UDP Checksum | /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
| Type |gzip | Reserved | Pair Count = X|Nexagon
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ /
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit State +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit State +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9: Uploaded detections packet format
Barkai, et al. Expires February 16,2023 [Page 10]
Internet-Draft LISP October 2022
Each H3Service is also an IP Multicast Source used to update
subscribers on the state of the h3.rS tiles in the h3.rB area.
We use [RFC8378] signal-free multicast to implement overlay channels.
Mobility-networks have many channels with thousands subscribers each.
MobilityClients driving through/subscribing to an h3.rB area issue
group address report based on any mechanism supported by [RFC8378].
Example report formats are specified in [RFC4604]. It is advised that
clients establish a ring of objects on their areas of interest.
Report messages are encapsulated between ClientXTRs and EdgeRTRs.
The day in a life of multicast update:
1. H3ServiceEID determines change or timing requiring an update
2. H3ServiceEID sends (S,G) update message via its ServerXTR
Outer Header src/dest: ServerXTR RLOC, EdgeRTR RLOC
Inner Header (S,G): H3ServerEID, EID chosen for theme
3. EdgeRTR resolves subscribed remote EdgeRTRs, replicates
Outer Header src/dest: EdgeRTR RLOC, remote EdgeRTR RLOC
Inner Header (S,G): H3ServerEID, EID chosen for theme
4. EdgeRTRs lookups subscribed ClientEIDs ClientXTRs RLOCs, replicates
Outer Header src/dest: EdgeRTR RLOC, ClientXTR RLOC
Inner Header (S,G): H3ServerEID, EID chosen for theme
5. ClientXTR delivers multicast channel update message to clientEID
Barkai, et al. Expires February 16,2023 [Page 11]
Internet-Draft LISP October 2022
Multicast update packets are of the following structure:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
|Version| Traffic Class | Flow Label | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| Payload Length | Next Header | Hop Limit | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| | |
+ + |
| | |
+ Source H3ServiceEID + |
| | IPv6
+ + |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| | |
+ + |
| | |
+ Group Address + |
| | |
+ + |
| | /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = xxxx | Dest Port = xxxx | \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ UDP
| UDP Length | UDP Checksum | /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
| |Nexagon
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ /
~ Nexagons Payload ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10: multicast update packet header
Barkai, et al. Expires February 16,2023 [Page 12]
Internet-Draft LISP October 2022
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
| Type = 1 |gzip | Reserved | Pair Count = X|Nexagon
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ /
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit State +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit State +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: multicast update payload, key-value, key-value..
Barkai, et al. Expires February 16,2023 [Page 13]
Internet-Draft LISP October 2022
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \
| Type = 2 |gzip | Reserved |H3R15 Count = X|Nexagon
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ /
| |
+ 64bit State +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ 64bit h3.rS ID +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 12: multicast update payload, value, key, key.. for larger areas
Barkai, et al. Expires February 16,2023 [Page 14]
Internet-Draft LISP October 2022
6. Security Considerations
The LISP mobility-network is inherently secure and private.
All information is conveyed to clients using provisioned Geolocation
Services. MobilityClients receive information only via geospatial
channels originating at provisioned services, replicated by EdgeRTRs.
All traffic is carried over encrypted tunnels.
7. Privacy Considerations
MobilityClients have no indication as to the origin of the raw data.
In order to be able to use the mobility-network for a given period,
the mobility clients go through a DNS/AAA stage by which they obtain
temporary clientEID and RLOCs of EdgeRTRs.
This MobilityClient to EdgeRTR interface is the most sensitive from
privacy perspective. The traffic on this interface is tunneled, its
detection content may be encrypted between ClientXTR to EdgeRTR.
Still, the EdgeRTR will know based on headers the client RLOC, and
the h3.rB area a client engages with.
Enterprises such as vehicle OEMs or carriers can "bring their own"
EdgeRTRs (BYO_RTR). BYO_RTRs are pre-provisioned to be able to use the
mapping system and are put on the approved list of the other EdgeRTRs.
A carrier offering EdgeRTR services on multiaccess edge compute (MEC)
is optimal for security and for traffic steering-replication.
Beyond client to EdgeRTR hop, the mapping system does not hold
MobilityClientEIDs info. Remote EdgeRTRs are only aware of clients
temporary EIDs. When EdgeRTRs register in the mapping for channels,
they do not register which clients use which EdgeRTR.
The H3ServiceEIDs decrypt and parse actual h3.rS detections. They also
consider MobilityClientEID credentials encoded in the client EID and
assigned by AAA. This helps avoid "fake-news", e.g. poorly made or
poorly localized detections.
Barkai, et al. Expires February 16,2023 [Page 15]
Internet-Draft LISP October 2022
In summary the privacy risk mitigations are:
(1) tapping: all communications are through tunnels therefore
may be encrypted using IP-Sec or other supported point to point
underlay standards.
(2) spoofing: it is very hard to guess a MobilityClientEID valid for
a short period of time. Clients and H3Services EIDs are provisioned
in EdgeRTRs, Clients using the AAA procedure, H3Services via dev-ops.
(3) credibility: the interface crowd-sources geo-state and does not
assume to trust single detections. Credit history track MobilityClient
EIDs as part of normal H3Services operation. The aggregate scores from
all objects are delivered to AAA subsystem for updating credentials.
(4) geo-privacy: Only EdgeRTRs are aware of both clients' RLOC and
geo-location, only AAA is aware of client IDs credentials and credit
but not geo-location. Ongoing client credit score adjustments span
all H3Services administratively to AAA without specific geo-source.
7. Acknowledgments
We would like to kindly thank Joel Halperin for helping structure the
AAA section and Geo-Privacy provisions, Luigi Lannone for promoting
such LISP Compute First Networking (CFN) use-cases, helping structure
the IANA section, and shepherding this draft to completion. We would
like to thank George Ericson from Dell, Lei Zhong from Toyota, Mikael
Klein from Ericsson, Leifeng Ruan from Intel, Ririn Andarini from NTT,
for helping with Geolocation and Dataflow Virtualization terminology
and key-issues during joint work at the AECC. We would like to thank
Professor Trevor Darrel and Professor Fisher Yu of BDD for reviewing
IANA enumerations for detections-consolidations feasible by visionAI
and Edge Computing. Finally we would like to thank Isaac Brodsky, Nick
Rabinowitz, David Ellis, and AJ Friend of the H3 steering committee
for reviewing the use of the H3 grid in the lisp-nexagon network.
Barkai, et al. Expires February 16,2023 [Page 16]
Internet-Draft LISP October 2022
8. IANA Considerations
This section provides guidance to the Internet Assigned Numbers
Authority (IANA) regarding registration of values related to the LISP
specification, in accordance with BCP 26 [RFC8126].
IANA is asked to create a registry named NEXAGON Parameters.
Such registry should be populated with the following sub registries.
Nexagon Header Bits
+----------+------------------+----------+---------------------------+
| Spec | IANA Name | Bit | Description |
| Name | | Position | |
+----------+------------------+----------+---------------------------+
| Type | nexagon-type | 0-7 | Type of key-value encoding|
| gzip | nexagon-gzip | 8-10 | gzip major version used |
| PairCount| nexagon-paircount| 24-31 | key-value pair count |
+----------+------------------+----------+---------------------------+
State Enumeration Field 0x0: Traffic Direction:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Lane North | [This Document] |
| | | |
| 0x2 | Lane North + 30 | [This Document] |
| | | |
| 0x3 | Lane North + 60 | [This Document] |
| | | |
| 0x4 | Lane North + 90 | [This Document] |
| | | |
| 0x5 | Lane North + 120 | [This Document] |
| | | |
| 0x6 | Lane North + 150 | [This Document] |
| | | |
| 0x7 | Lane North + 180 | [This Document] |
| | | |
| 0x8 | Lane North + 210 | [This Document] |
| | | |
| 0x9 | Lane North + 240 | [This Document] |
| | | |
| 0xA | Lane North + 270 | [This Document] |
| | | |
| 0xB | Lane North + 300 | [This Document] |
| | | |
| 0xC | Lane North + 330 | [This Document] |
| | | |
| 0xD | Junction | [This Document] |
| | | |
| 0xE | Shoulder | [This Document] |
| | | |
| 0xF | Sidewalk | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 17]
Internet-Draft LISP October 2022
State Enumeration Field 0x1: Persistent Condition:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Pothole Light | [This Document] |
| | | |
| 0x2 | Pothole Deep | [This Document] |
| | | |
| 0x3 | Speed-bump Low | [This Document] |
| | | |
| 0x4 | Speed-bump High | [This Document] |
| | | |
| 0x5 | Icy | [This Document] |
| | | |
| 0x6 | Flooded | [This Document] |
| | | |
| 0x7 | Snow-cover | [This Document] |
| | | |
| 0x8 | Deep Snow | [This Document] |
| | | |
| 0x9 | Cone | [This Document] |
| | | |
| 0xA | Gravel | [This Document] |
| | | |
| 0xB | Choppy | [This Document] |
| | | |
| 0xC | Blind-Curve | [This Document] |
| | | |
| 0xD | Steep | [This Document] |
| | | |
| 0xE | Low-bridge | [This Document] |
| | | |
| 0xF | Other | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 18]
Internet-Draft LISP October 2022
State Enumeration Field 0x2: Transient Condition:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Jaywalker | [This Document] |
| | | |
| 0x2 | Bike or Scooter | [This Document] |
| | | |
| 0x3 | Stopped Vehicle | [This Document] |
| | | |
| 0x4 | Moving on Shoulder | [This Document] |
| | | |
| 0x5 | First Responder | [This Document] |
| | | |
| 0x6 | Sudden Slowdown | [This Document] |
| | | |
| 0x7 | Oversize Vehicle | [This Document] |
| | | |
| 0x8 | Light/Sign Breach | [This Document] |
| | | |
| 0x9 | Collision Light | [This Document] |
| | | |
| 0xA | Collision Severe | [This Document] |
| | | |
| 0xB | Collision Debris | [This Document] |
| | | |
| 0xC | Collision Course | [This Document] |
| | | |
| 0xD | Vehicle Hard Brake | [This Document] |
| | | |
| 0xE | Vehicle Sharp Turn | [This Document] |
| | | |
| 0xF | Freed-up Parking | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 19]
Internet-Draft LISP October 2022
State Enumeration Field 0x3: Traffic-light Counter:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | 1 Second to Green | [This Document] |
| | | |
| 0x2 | 2 Second to Green | [This Document] |
| | | |
| 0x3 | 3 Second to Green | [This Document] |
| | | |
| 0x4 | 4 Second to Green | [This Document] |
| | | |
| 0x5 | 5 Second to Green | [This Document] |
| | | |
| 0x6 | 6 Second to Green | [This Document] |
| | | |
| 0x7 | 7 Second to Green | [This Document] |
| | | |
| 0x8 | 8 Second to Green | [This Document] |
| | | |
| 0x9 | 9 Second to Green | [This Document] |
| | | |
| 0xA | 10 Second to Green | [This Document] |
| | | |
| 0xB | 20 Second to Green | [This Document] |
| | | |
| 0xC | 30 Second to Green | [This Document] |
| | | |
| 0xD | 60 Second to Green | [This Document] |
| | | |
| 0xE | Green Now | [This Document] |
| | | |
| 0xF | Red Now | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 20]
Internet-Draft LISP October 2022
State Enumeration Field 0x4: Impacted Tile:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Epicenter | [This Document] |
| | | |
| 0x2 | 2 Tiles Away | [This Document] |
| | | |
| 0x3 | 3 Tiles Away | [This Document] |
| | | |
| 0x4 | 4 Tiles Away | [This Document] |
| | | |
| 0x5 | 5 Tiles Away | [This Document] |
| | | |
| 0x6 | 6 Tiles Away | [This Document] |
| | | |
| 0x7 | 7 Tiles Away | [This Document] |
| | | |
| 0x8 | 8 Tiles Away | [This Document] |
| | | |
| 0x9 | 9 Tiles Away | [This Document] |
| | | |
| 0xA | 10 Tiles Away | [This Document] |
| | | |
| 0xB | 20 Tiles Away | [This Document] |
| | | |
| 0xC | 30 Tiles Away | [This Document] |
| | | |
| 0xD | 60 Tiles Away | [This Document] |
| | | |
| 0xE | <100 Tiles Away | [This Document] |
| | | |
| 0xF | <200 Tiles Away | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 21]
Internet-Draft LISP October 2022
State Enumeration Field 0x5: Expected Duration:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Next 1 Second | [This Document] |
| | | |
| 0x2 | Next 5 Seconds | [This Document] |
| | | |
| 0x3 | Next 10 Seconds | [This Document] |
| | | |
| 0x4 | Next 20 Seconds | [This Document] |
| | | |
| 0x5 | Next 40 Seconds | [This Document] |
| | | |
| 0x6 | Next 60 Seconds | [This Document] |
| | | |
| 0x7 | Next 2 Minutes | [This Document] |
| | | |
| 0x8 | Next 3 Minutes | [This Document] |
| | | |
| 0x9 | Next 4 Minutes | [This Document] |
| | | |
| 0xA | Next 5 Minutes | [This Document] |
| | | |
| 0xB | Next 10 Minutes | [This Document] |
| | | |
| 0xC | Next 15 Minutes | [This Document] |
| | | |
| 0xD | Next 30 Minutes | [This Document] |
| | | |
| 0xE | Next 60 Minutes | [This Document] |
| | | |
| 0xF | Next 24 Hours | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 22]
Internet-Draft LISP October 2022
State Enumeration Field 0x6: Lane Right Sign:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Yield | [This Document] |
| | | |
| 0x2 | Speed Limit | [This Document] |
| | | |
| 0x3 | Straight Only | [This Document] |
| | | |
| 0x4 | No Straight | [This Document] |
| | | |
| 0x5 | Right Only | [This Document] |
| | | |
| 0x6 | No Right | [This Document] |
| | | |
| 0x7 | Left Only | [This Document] |
| | | |
| 0x8 | No Left | [This Document] |
| | | |
| 0x9 | Right Straight | [This Document] |
| | | |
| 0xA | Left Straight | [This Document] |
| | | |
| 0xB | No U Turn | [This Document] |
| | | |
| 0xC | No Left or U | [This Document] |
| | | |
| 0xD | Bike Lane | [This Document] |
| | | |
| 0xE | HOV Lane | [This Document] |
| | | |
| 0xF | Stop | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 23]
Internet-Draft LISP October 2022
State Enumeration Field 0x7: Movement Sign:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Keep Right | [This Document] |
| | | |
| 0x2 | Keep Left | [This Document] |
| | | |
| 0x3 | Stay in Lane | [This Document] |
| | | |
| 0x4 | Do Not Enter | [This Document] |
| | | |
| 0x5 | No Trucks | [This Document] |
| | | |
| 0x6 | No Bikes | [This Document] |
| | | |
| 0x7 | No Peds | [This Document] |
| | | |
| 0x8 | One Way | [This Document] |
| | | |
| 0x9 | Parking | [This Document] |
| | | |
| 0xA | No Parking | [This Document] |
| | | |
| 0xB | No Standing | [This Document] |
| | | |
| 0xC | No Passing | [This Document] |
| | | |
| 0xD | Loading Zone | [This Document] |
| | | |
| 0xE | Rail Crossing | [This Document] |
| | | |
| 0xF | School Zone | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 24]
Internet-Draft LISP October 2022
State Enumeration Field 0x8: Curves & Intersections:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | Turns Left | [This Document] |
| | | |
| 0x2 | Turns Right | [This Document] |
| | | |
| 0x3 | Curves Left | [This Document] |
| | | |
| 0x4 | Curves Right | [This Document] |
| | | |
| 0x5 | Reverses Left | [This Document] |
| | | |
| 0x6 | Reverses Right | [This Document] |
| | | |
| 0x7 | Winding Road | [This Document] |
| | | |
| 0x8 | Hair Pin | [This Document] |
| | | |
| 0x9 | Pretzel Turn | [This Document] |
| | | |
| 0xA | Cross Roads | [This Document] |
| | | |
| 0xB | Cross T | [This Document] |
| | | |
| 0xC | Cross Y | [This Document] |
| | | |
| 0xD | Circle | [This Document] |
| | | |
| 0xE | Lane Ends | [This Document] |
| | | |
| 0xF | Road Narrows | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 25]
Internet-Draft LISP October 2022
State Enumeration Field 0x9: Tile Traffic Speed:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | < 1 m/sec | [This Document] |
| | | |
| 0x2 | < 2 m/sec | [This Document] |
| | | |
| 0x3 | < 3 m/sec | [This Document] |
| | | |
| 0x4 | < 4 m/sec | [This Document] |
| | | |
| 0x5 | < 5 m/sec | [This Document] |
| | | |
| 0x6 | < 6 m/sec | [This Document] |
| | | |
| 0x7 | < 7 m/sec | [This Document] |
| | | |
| 0x8 | < 8 m/sec | [This Document] |
| | | |
| 0x9 | < 9 m/sec | [This Document] |
| | | |
| 0xA | < 10 m/sec | [This Document] |
| | | |
| 0xB | < 20 m/sec | [This Document] |
| | | |
| 0xC | < 30 m/sec | [This Document] |
| | | |
| 0xD | < 40 m/sec | [This Document] |
| | | |
| 0xE | < 50 m/sec | [This Document] |
| | | |
| 0xF | > 50 m/sec | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 26]
Internet-Draft LISP October 2022
State Enumeration Field 0xA: Pedestrian Curb Density:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | 100% | [This Document] |
| | | |
| 0x2 | 95% | [This Document] |
| | | |
| 0x3 | 90% | [This Document] |
| | | |
| 0x4 | 85% | [This Document] |
| | | |
| 0x5 | 80% | [This Document] |
| | | |
| 0x6 | 70% | [This Document] |
| | | |
| 0x7 | 60% | [This Document] |
| | | |
| 0x8 | 50% | [This Document] |
| | | |
| 0x9 | 40% | [This Document] |
| | | |
| 0xA | 30% | [This Document] |
| | | |
| 0xB | 20% | [This Document] |
| | | |
| 0xC | 15% | [This Document] |
| | | |
| 0xD | 10% | [This Document] |
| | | |
| 0xE | 5% | [This Document] |
| | | |
| 0xF | No Peds | [This Document] |
+-------+--------------------+-----------------+
Barkai, et al. Expires February 16,2023 [Page 27]
Internet-Draft LISP October 2022
State Enumeration Field 0xB: Local Zone Speed Limit:
+-------+--------------------+-----------------+
| Value | Description | Reference |
+-------+--------------------+-----------------+
| 0x0 | Null | [This Document] |
| | | |
| 0x1 | 1 m/sec | [This Document] |
| | | |
| 0x2 | 2 m/sec | [This Document] |
| | | |
| 0x3 | 3 m/sec | [This Document] |
| | | |
| 0x4 | 4 m/sec | [This Document] |
| | | |
| 0x5 | 5 m/sec | [This Document] |
| | | |
| 0x6 | 6 m/sec | [This Document] |
| | | |
| 0x7 | 7 m/sec | [This Document] |
| | | |
| 0x8 | 8 m/sec | [This Document] |
| | | |
| 0x9 | 9 m/sec | [This Document] |
| | | |
| 0xA | 10 m/sec | [This Document] |
| | | |
| 0xB | 15 m/sec | [This Document] |
| | | |
| 0xC | 20 m/sec | [This Document] |
| | | |
| 0xD | 25 m/sec | [This Document] |
| | | |
| 0xE | 30 m/sec | [This Document] |
| | | |
| 0xF | 35 m/sec | [This Document] |
+-------+--------------------+-----------------+
State enumeration fields 0xC, 0xD, 0xE, 0xF, are unassigned.
IANA can assign them on a "First Come First Served" basis
according to [RFC8126].
Barkai, et al. Expires February 16,2023 [Page 28]
Internet-Draft LISP October 2022
9. Normative References
[I-D.ietf-lisp-rfc6830bis]
Farinacci, D., Fuller, V., Meyer, D., Lewis, D., and A.
Cabellos-Aparicio, "The Locator/ID Separation Protocol
(LISP)", draft-ietf-lisp-rfc6830bis-38 (work in progress),
May 2020.
[I-D.ietf-lisp-rfc6833bis]
Farinacci, D., Maino, F., Fuller, V., and A. Cabellos,
"Locator/ID Separation Protocol (LISP) Control-Plane",
draft-ietf-lisp-rfc6833bis-31 (work in progress), May
2020.
[RFC4604] Holbrook, H., Cain, B., and B. Haberman, "Using Internet
Group Management Protocol Version 3 (IGMPv3) and Multicast
Listener Discovery Protocol Version 2 (MLDv2) for Source-
Specific Multicast", RFC 4604, DOI 10.17487/RFC4604,
August 2006, <https://www.rfc-editor.org/info/rfc4604>.
[RFC6733] Fajardo, V., Ed., Arkko, J., Loughney, J., and G. Zorn,
Ed., "Diameter Base Protocol", RFC 6733,
DOI 10.17487/RFC6733, October 2012,
<http://www.rfc-editor.org/info/rfc6733>.
[RFC8126] Cotton, M., Leiba, B., Narten, T., "Guidelines for
Writing an IANA Considerations Section in RFCs", RFC8126,
DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
[RFC8378] Farinacci, D., Moreno, V., "Signal-Free Locator/ID
Separation Protocol (LISP) Multicast", RFC8378,
DOI 10.17487/RFC8378, May 2018,
<https://www.rfc-editor.org/info/rfc8378>.
[RFC8060] Farinacci, D., Meyer, D., and J. Snijders, "LISP Canonical
Address Format (LCAF)", RFC 8060, DOI 10.17487/RFC8060,
February 2017, <http://www.rfc-editor.org/info/rfc8060>.
[H3] Uber Technologies Inc. [n.d.]. H3: Ubers Hexagonal
Hierarchical Spatial Index, May 2021,
<https://eng.uber.com/h3>.
[BDD] Fisher Yu, Wenqi Xian, Yingying Chen, Fangchen Liu, Mike
Liao, Vashisht Madhavan, and Trevor Darrell. BDD100K: A
diverse driving video database with scalable annotation
tooling. arXiv:1805.04687, 2018. 2, 3
<https://doi.org/10.48550/arXiv.1805.04687>
Barkai, et al. Expires February 16,2023 [Page 29]
Internet-Draft LISP October 2022
Authors' Addresses
Sharon Barkai
Nexar
CA
USA
Email: sbarkai@gmail.com
Bruno Fernandez-Ruiz
Nexar
London
UK
Email: b@getnexar.com
Rotem Tamir
Nexar
Israel
rotemtamir@getnexar.com
Alberto Rodriguez-Natal
Cisco Systems
170 Tasman Drive
San Jose, CA
USA
Email: natal@cisco.com
Fabio Maino
Cisco Systems
170 Tasman Drive
San Jose, CA
USA
Email: fmaino@cisco.com
Barkai, et al. Expires February 16,2023 [Page 30]
Internet-Draft LISP October 2022
Albert Cabellos-Aparicio
Technical University of Catalonia
Barcelona
Spain
Email: acabello@ac.upc.edu
Jordi Paillisse-Vilanova
Technical University of Catalonia
Barcelona
Spain
Email: jordip@ac.upc.edu
Dino Farinacci
lispers.net
San Jose, CA
USA
Email: farinacci@gmail.com
Barkai, et al. Expires February 16,2023 [Page 31]