lpwan Working Group JC. Zuniga
Internet-Draft SIGFOX
Intended status: Standards Track C. Gomez
Expires: January 10, 2022 S. Aguilar
Universitat Politecnica de Catalunya
L. Toutain
IMT-Atlantique
S. Cespedes
D. Wistuba
NIC Labs, Universidad de Chile
July 9, 2021
SCHC over Sigfox LPWAN
draft-ietf-lpwan-schc-over-sigfox-07
Abstract
The Generic Framework for Static Context Header Compression and
Fragmentation (SCHC) specification describes two mechanisms: i) an
application header compression scheme, and ii) a frame fragmentation
and loss recovery functionality. SCHC offers a great level of
flexibility that can be tailored for different Low Power Wide Area
Network (LPWAN) technologies.
The present document provides the optimal parameters and modes of
operation when SCHC is implemented over a Sigfox LPWAN. This set of
parameters are also known as a "SCHC over Sigfox profile."
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 10, 2022.
Zuniga, et al. Expires January 10, 2022 [Page 1]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. SCHC over Sigfox . . . . . . . . . . . . . . . . . . . . . . 3
3.1. Network Architecture . . . . . . . . . . . . . . . . . . 3
3.2. Uplink . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.3. Downlink . . . . . . . . . . . . . . . . . . . . . . . . 6
3.4. SCHC-ACK on Downlink . . . . . . . . . . . . . . . . . . 7
3.5. SCHC Rules . . . . . . . . . . . . . . . . . . . . . . . 7
3.6. Fragmentation . . . . . . . . . . . . . . . . . . . . . . 7
3.6.1. Uplink Fragmentation . . . . . . . . . . . . . . . . 8
3.6.2. Downlink Fragmentation . . . . . . . . . . . . . . . 11
3.7. SCHC-over-Sigfox F/R Message Formats . . . . . . . . . . 12
3.7.1. Uplink ACK-on-Error Mode: Single-byte SCHC Header . . 12
3.7.2. Uplink ACK-on-Error Mode: Two-byte SCHC Header . . . 16
3.8. Padding . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Fragmentation Sequence Examples . . . . . . . . . . . . . . . 19
4.1. Uplink No-ACK Examples . . . . . . . . . . . . . . . . . 19
4.2. Uplink ACK-on-Error Examples: Single-byte SCHC Header . . 20
4.3. SCHC Abort Examples . . . . . . . . . . . . . . . . . . . 27
5. Security considerations . . . . . . . . . . . . . . . . . . . 29
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 29
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1. Normative References . . . . . . . . . . . . . . . . . . 30
7.2. Informative References . . . . . . . . . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 30
1. Introduction
The Generic Framework for Static Context Header Compression and
Fragmentation (SCHC) specification [RFC8724] describes two
mechanisms: i) a frame fragmentation and loss recovery functionality,
Zuniga, et al. Expires January 10, 2022 [Page 2]
Internet-Draft SCHC over Sigfox LPWAN July 2021
and ii) an application header compression scheme. Either can be used
on top of all the four LWPAN technologies defined in [RFC8376].
These LPWANs have similar characteristics such as star-oriented
topologies, network architecture, connected devices with built-in
applications, etc.
SCHC offers a great level of flexibility to accommodate all these
LPWAN technologies. Even though there are a great number of
similarities between them, some differences exist with respect to the
transmission characteristics, payload sizes, etc. Hence, there are
optimal parameters and modes of operation that can be used when SCHC
is used on top of a specific LPWAN technology.
This document describes the recommended parameters, settings, and
modes of operation to be used when SCHC is implemented over a Sigfox
LPWAN. This set of parameters are also known as a "SCHC over Sigfox
profile."
2. Terminology
It is assumed that the reader is familiar with the terms and
mechanisms defined in [RFC8376] and in [RFC8724].
3. SCHC over Sigfox
The Generic SCHC Framework described in [RFC8724] takes advantage of
the predictability of data flows existing in LPWAN applications to
avoid context synchronization.
Contexts need to be stored and pre-configured on both ends. This can
be done either by using a provisioning protocol, by out of band
means, or by pre-provisioning them (e.g. at manufacturing time). The
way contexts are configured and stored on both ends is out of the
scope of this document.
3.1. Network Architecture
Figure 1 represents the architecture for compression/decompression
(C/D) and fragmentation/reassembly (F/R) based on the terminology
defined in [RFC8376], where the Radio Gateway (RG) is a Sigfox Base
Station and the Network Gateway (NGW) is the Sigfox cloud-based
Network.
Zuniga, et al. Expires January 10, 2022 [Page 3]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sigfox Device Application
+----------------+ +--------------+
| APP1 APP2 APP3 | |APP1 APP2 APP3|
+----------------+ +--------------+
| UDP | | | | UDP |
| IPv6 | | | | IPv6 |
+--------+ | | +--------+
| SCHC C/D & F/R | | |
| | | |
+-------+--------+ +--------+-----+
$ .
$ +---------+ +--------------+ +---------+ .
$ | | | | | Network | .
+~~ |Sigfox BS| |Sigfox Network| | SCHC | .
| (RG) | === | (NGW) | === |C/D & F/R|.....
+---------+ +--------------+ +---------+
Figure 1: Network Architecture
In the case of the global Sigfox Network, RGs (or Base Stations) are
distributed over multiple countries wherever the Sigfox LPWAN service
is provided. The NGW (or cloud-based Sigfox Core Network) is a
single entity that connects to all Sigfox base stations in the world,
providing hence a global single star network topology.
The Device sends application flows that are compressed and/or
fragmented by a SCHC Compressor/Decompressor (SCHC C/D + F/R) to
reduce headers size and/or fragment the packet. The resulting SCHC
Message is sent over a layer two (L2) Sigfox frame to the Sigfox Base
Stations, which then forward the SCHC Message to the Network Gateway
(NGW). The NGW then delivers the SCHC Message and associated
gathered metadata to the Network SCHC C/D + F/R.
The Sigfox Network (NGW) communicates with the Network SCHC C/D + F/R
for compression/decompression and/or for fragmentation/reassembly.
The Network SCHC C/D + F/R shares the same set of rules as the Dev
SCHC C/D + F/R. The Network SCHC C/D + F/R can be collocated with
the NGW or it could be located in a different place, as long as a
tunnel or secured communication is established between the NGW and
the SCHC C/D + F/R functions. After decompression and/or reassembly,
the packet can be forwarded over the Internet to one (or several)
LPWAN Application Server(s) (App).
The SCHC C/D + F/R processes are bidirectional, so the same
principles are applicable on both uplink (UL) and downlink (DL).
Zuniga, et al. Expires January 10, 2022 [Page 4]
Internet-Draft SCHC over Sigfox LPWAN July 2021
3.2. Uplink
Uplink Sigfox transmissions occur in repetitions over different times
and frequencies. Besides time and frequency diversities, the Sigfox
network also provides space diversity, as potentially an uplink
message will be received by several base stations.
Since all messages are self-contained and base stations forward all
these messages back to the same Sigfox Network, multiple input copies
can be combined at the NGW providing for extra reliability based on
the triple diversity (i.e., time, space and frequency).
A detailed description of the Sigfox Radio Protocol can be found in
[sigfox-spec].
Messages sent from the Device to the Network are delivered by the
Sigfox network (NGW) to the Network SCHC C/D + F/R through a
callback/API with the following information:
o Device ID
o Message Sequence Number
o Message Payload
o Message Timestamp
o Device Geolocation (optional)
o RSSI (optional)
o Device Temperature (optional)
o Device Battery Voltage (optional)
The Device ID is a globally unique identifier assigned to the Device,
which is included in the Sigfox header of every message. The Message
Sequence Number is a monotonically increasing number identifying the
specific transmission of this uplink message, and it is also part of
the Sigfox header. The Message Payload corresponds to the payload
that the Device has sent in the uplink transmission.
The Message Timestamp, Device Geolocation, RSSI, Device Temperature
and Device Battery Voltage are metadata parameters provided by the
Network.
A detailed description of the Sigfox callbacks/APIs can be found in
[sigfox-callbacks].
Zuniga, et al. Expires January 10, 2022 [Page 5]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Only messages that have passed the L2 Cyclic Redundancy Check (CRC)
at network reception are delivered by the Sigfox Network to the
Network SCHC C/D + F/R.
+---------------+-----------------+
| Sigfox Header | Sigfox payload |
+---------------+---------------- +
| SCHC message |
+-----------------+
Figure 2: SCHC Message in Sigfox
Figure 2 shows a SCHC Message sent over Sigfox, where the SCHC
Message could be a full SCHC Packet (e.g. compressed) or a SCHC
Fragment (e.g. a piece of a bigger SCHC Packet).
3.3. Downlink
Downlink transmissions are Device-driven and can only take place
following an uplink communication that so indicates. Hence, a Device
explicitly indicates its intention to receive a downlink message
using a donwlink request flag when sending the preceding uplink
message to the network. After completing the uplink transmission,
the Device opens a fixed window for downlink reception. The delay
and duration of the reception opportunity window have fixed values.
If there is a downlink message to be sent for this given Device (e.g.
either a response to the uplink message or queued information waiting
to be transmitted), the network transmits this message to the Device
during the reception window. If no message is received by the Device
after the reception opportunity window has elapsed, the Device closes
the reception window opportunity and gets back to the normal mode
(e.g., continue UL transmissions, sleep, stand-by, etc.)
When a downlink message is sent to a Device, a reception
acknowledgement is generated by the Device and sent back to the
Network through the Sigfox radio protocol and reported in the Sigfox
Network backend.
A detailed description of the Sigfox Radio Protocol can be found in
[sigfox-spec] and a detailed description of the Sigfox callbacks/APIs
can be found in [sigfox-callbacks].
Zuniga, et al. Expires January 10, 2022 [Page 6]
Internet-Draft SCHC over Sigfox LPWAN July 2021
3.4. SCHC-ACK on Downlink
As explained previously, downlink transmissions are Device-driven and
can only take place following a specific uplink transmission that
indicates and allows a following downlink opportunity. For this
reason, when SCHC bi-directional services are used (e.g. Ack-on-
Error fragmentation mode) the SCHC protocol implementation needs to
consider the times when a downlink message (e.g. SCHC-ACK) can be
sent and/or received.
For the UL ACK-on-Error fragmentation mode, a DL opportunity MUST be
indicated by the last fragment of every window (i.e. FCN = All-0, or
FCN = All-1). The Device sends the fragments in sequence and, after
transmitting the FCN = All-0 or FCN = All-1, it opens up a reception
opportunity. The Network SCHC can then decide to respond at that
opportunity (or wait for a further one) with a SCHC-ACK indicating in
case there are missing fragments from the current or previous
windows. If there is no SCHC-ACK to be sent, or if the network
decides to wait for a further DL transmission opportunity, then no DL
transmission takes place at that opportunity and after a timeout the
UL transmissions continue. Intermediate SCHC fragments with FCN
different from All-0 or All-1 MUST NOT use the DL request flag to
request a SCHC-ACK.
3.5. SCHC Rules
The RuleID MUST be included in the SCHC header. The total number of
rules to be used affects directly the Rule ID field size, and
therefore the total size of the fragmentation header. For this
reason, it is recommended to keep the number of rules that are
defined for a specific device to the minimum possible.
RuleIDs can be used to differentiate data traffic classes (e.g. QoS,
control vs. data, etc.), and data sessions. They can also be used to
interleave simultaneous fragmentation sessions between a Device and
the Network.
3.6. Fragmentation
The SCHC specification [RFC8724] defines a generic fragmentation
functionality that allows sending data packets or files larger than
the maximum size of a Sigfox payload. The functionality also defines
a mechanism to send reliably multiple messages, by allowing to resend
selectively any lost fragments.
The SCHC fragmentation supports several modes of operation. These
modes have different advantages and disadvantages depending on the
specifics of the underlying LPWAN technology and application Use
Zuniga, et al. Expires January 10, 2022 [Page 7]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Case. This section describes how the SCHC fragmentation
functionality should optimally be implemented when used over a Sigfox
LPWAN for the most typical Use Case applications.
As described in section 8.2.3 of [RFC8724], the integrity of the
fragmentation-reassembly process of a SCHC Packet MUST be checked at
the receive end. Since only UL messages/fragments that have passed
the CRC-check are delivered to the Network SCHC C/D + F/R, and each
one has an associated Sigfox Message Sequence Number (see
Section 3.2), integrity can be guaranteed when no consecutive
messages are missing from the sequence and all FCN bitmaps are
complete. In order to support multiple flows/RuleIDs (potentially
interleaved), the implementation of a central message sequence
counter at the Network SCHC C/D + F/R is required. With this
functionality and in order to save protocol overhead, the use of a
dedicated Reassembly Check Sequence (RCS) is NOT RECOMMENDED.
The L2 Word Size used by Sigfox is 1 byte (8 bits).
3.6.1. Uplink Fragmentation
Sigfox uplink transmissions are completely asynchronous and take
place in any random frequency of the allowed uplink bandwidth
allocation. In addition, devices may go to deep sleep mode, and then
wake up and transmit whenever there is a need to send information to
the network. Data packets are self-contained (aka "message in a
bottle") with all the required information for the network to process
them accordingly. Hence, there is no need to perform any network
attachment, synchronization, or other procedure before transmitting a
data packet.
Since uplink transmissions are asynchronous, a SCHC fragment can be
transmitted at any given time by the Device. Sigfox uplink messages
are fixed in size, and as described in [RFC8376] they can carry 0-12
bytes payload. Hence, a single SCHC Tile size per fragmentation mode
can be defined so that every Sigfox message always carries one SCHC
Tile.
When the ACK-on-Error mode is used for uplink fragmentation, the SCHC
Compound ACK defined in [I-D.ietf-lpwan-schc-compound-ack]) MUST be
used in the downlink responses.
3.6.1.1. Uplink No-ACK Mode
No-ACK is RECOMMENDED to be used for transmitting short, non-critical
packets that require fragmentation and do not require full
reliability. This mode can be used by uplink-only devices that do
Zuniga, et al. Expires January 10, 2022 [Page 8]
Internet-Draft SCHC over Sigfox LPWAN July 2021
not support downlink communications, or by bidirectional devices when
they send non-critical data.
Since there are no multiple windows in the No-ACK mode, the W bit is
not present. However it is RECOMMENDED to use the FCN field to
indicate the size of the data packet. In this sense, the data packet
would need to be splitted into X fragments and, similarly to the
other fragmentation modes, the first transmitted fragment would need
to be marked with FCN = X-1. Consecutive fragments MUST be marked
with decreasing FCN values, having the last fragment marked with FCN
= (All-1). Hence, even though the No-ACK mode does not allow
recovering missing fragments, it allows indicating implicitly the
size of the expected packet to the Network and hence detect at the
receiver side whether all fragments have been received or not.
The RECOMMENDED Fragmentation Header size is 8 bits, and it is
composed as follows:
o RuleID size: 4 bits
o DTag size (T): 0 bits
o Fragment Compressed Number (FCN) size (N): 4 bits
o As per [RFC8724], in the No-ACK mode the W (window) field is not
present.
o RCS size: 0 bits (Not used)
3.6.1.2. Uplink ACK-on-Error Mode: Single-byte SCHC Header
ACK-on-Error with single-byte header is RECOMMENDED for medium to
large size packets that need to be sent reliably. ACK-on-Error is
optimal for Sigfox transmissions, since it leads to a reduced number
of ACKs in the lower capacity downlink channel. Also, downlink
messages can be sent asynchronously and opportunistically.
Allowing transmission of packets/files up to 300 bytes long, the SCHC
uplink Fragmentation Header size is RECOMMENDED to be 8 bits in size
and is composed as follows:
o Rule ID size: 3 bits
o DTag size (T): 0 bits
o Window index (W) size (M): 2 bits
o Fragment Compressed Number (FCN) size (N): 3 bits
Zuniga, et al. Expires January 10, 2022 [Page 9]
Internet-Draft SCHC over Sigfox LPWAN July 2021
o MAX_ACK_REQUESTS: 5
o WINDOW_SIZE: 7 (with a maximum value of FCN=0b110)
o Tile size: 11 bytes
o Retransmission Timer: Application-dependent
o Inactivity Timer: Application-dependent
o RCS size: 0 bits (Not used)
The correspondent SCHC ACK in the downlink is 13 bits long, so
padding is needed to complete the required 64 bits of Sigfox payload.
3.6.1.3. Uplink ACK-on-Error Mode: Two-byte SCHC Header
ACK-on-Error with two-byte header is RECOMMENDED for very large size
packets that need to be sent reliably. ACK-on-Error is optimal for
Sigfox transmissions, since it leads to a reduced number of ACKs in
the lower capacity downlink channel. Also, downlink messages can be
sent asynchronously and opportunistically.
In order to allow transmission of very large packets/files up to 2250
bytes long, the SCHC uplink Fragmentation Header size is RECOMMENDED
to be 16 bits in size and composed as follows:
o Rule ID size is: 8 bits
o DTag size (T) is: 0 bits
o Window index (W) size (M): 3 bits
o Fragment Compressed Number (FCN) size (N): 5 bits.
o MAX_ACK_REQUESTS: 5
o WINDOW_SIZE: 31 (with a maximum value of FCN=0b11110)
o Tile size: 10 bytes
o Retransmission Timer: Application-dependent
o Inactivity Timer: Application-dependent
o RCS size: 0 bits (Not used)
Zuniga, et al. Expires January 10, 2022 [Page 10]
Internet-Draft SCHC over Sigfox LPWAN July 2021
The correspondent SCHC ACK in the downlink is 43 bits long, so
padding is needed to complete the required 64 bits of Sigfox payload.
3.6.1.4. All-1 behaviour + Sigfox Sequence Number
For ACK-on-Error, as defined in [RFC8724], it is expected that the
last SCHC fragment of the last window will always be delivered with
an All-1 FCN. Since this last window may not be full (i.e. it may be
comprised of less than WINDOW_SIZE fragments), an All-1 fragment may
follow a value of FCN higher than 1 (0b01). In this case, the
receiver could not derive from the FCN values alone whether there are
any missing fragments right before the All-1 fragment or not.
However, since a Message Sequence Number is provided by the Sigfox
protocol together with the Sigfox Payload, the receiver can detect if
there are missing fragments before the All-1 and hence construct the
corresponding SCHC ACK Bitmap accordingly.
3.6.2. Downlink Fragmentation
In some LPWAN technologies, as part of energy-saving techniques,
downlink transmission is only possible immediately after an uplink
transmission. This allows the device to go in a very deep sleep mode
and preserve battery, without the need to listen to any information
from the network. This is the case for Sigfox-enabled devices, which
can only listen to downlink communications after performing an uplink
transmission and requesting a downlink.
When there are fragments to be transmitted in the downlink, an uplink
message is required to trigger the downlink communication. In order
to avoid potentially high delay for fragmented datagram transmission
in the downlink, the fragment receiver MAY perform an uplink
transmission as soon as possible after reception of a downlink
fragment that is not the last one. Such uplink transmission MAY be
triggered by sending a SCHC message, such as a SCHC ACK. However,
other data messages can equally be used to trigger DL communications.
Sigfox downlink messages are fixed in size, and as described in
[RFC8376] they can carry up to 8 bytes payload. Hence, a single SCHC
Tile size per mode can be defined so that every Sigfox message always
carries one SCHC Tile.
For reliable downlink fragment transmission, the ACK-Always mode is
RECOMMENDED.
The SCHC downlink Fragmentation Header size is RECOMMENDED to be 8
bits in size and is composed as follows:
Zuniga, et al. Expires January 10, 2022 [Page 11]
Internet-Draft SCHC over Sigfox LPWAN July 2021
o RuleID size: 3 bits
o DTag size (T): 0 bits
o Window index (W) size (M) is: 0 bits
o Fragment Compressed Number (FCN) size (N): 5 bits
o MAX_ACK_REQUESTS: 5
o WINDOW_SIZE: 31 (with a maximum value of FCN=0b11110)
o Tile size: 7 bytes
o Retransmission Timer: Application-dependent
o Inactivity Timer: Application-dependent
o RCS size: 0 bits (Not used)
3.7. SCHC-over-Sigfox F/R Message Formats
This section depicts the different formats of SCHC Fragment, SCHC ACK
(including the SCHC Compound ACK defined in
[I-D.ietf-lpwan-schc-compound-ack]), and SCHC Abort used in SCHC over
Sigfox.
3.7.1. Uplink ACK-on-Error Mode: Single-byte SCHC Header
3.7.1.1. Regular SCHC Fragment
Figure 3 shows an example of a regular SCHC fragment for all
fragments except the last one. As tiles are of 11 bytes, padding
MUST NOT be added.
|-- SCHC Fragment Header --|
+ ------------------------ + ------- +
| RuleID | W | FCN | Payload |
+ ------ + ------ + ------ + ------- +
| 3 bits | 2 bits | 3 bits | 88 bits |
Figure 3: Regular SCHC Fragment format for all fragments except the
last one
The use of SCHC ACK REQ is NOT RECOMMENDED, instead the All-1 SCHC
Fragment SHOULD be used to request a SCHC ACK from the receiver
Zuniga, et al. Expires January 10, 2022 [Page 12]
Internet-Draft SCHC over Sigfox LPWAN July 2021
(Network SCHC). As per [RFC8724], the All-0 message is
distinguishable from the SCHC ACK REQ (All-1 message). The
penultimate tile of a SCHC Packet is of regular size.
3.7.1.2. All-1 SCHC Fragment
Figure 4 shows an example of the All-1 message. The All-1 message
MUST contain the last tile of the SCHC Packet. The last tile MUST be
of at least 1 byte (one L2 word). Padding MUST NOT be added, as the
resulting size is L2-word-multiple.
|--- SCHC Fragment Header ---|
+ --------------------------- + ------------ +
| RuleID | W | FCN=ALL-1 | Payload |
+ ------ + ------ + --------- + ------------ +
| 3 bits | 2 bits | 3 bits | 8 to 88 bits |
Figure 4: All-1 SCHC Message format with last tile
As per [RFC8724] the All-1 must be distinguishable from a SCHC
Sender-Abort message (with same Rule ID, M, and N values). The All-1
MUST have the last tile of the SCHC Packet, which MUST be of at least
1 byte. The SCHC Sender-Abort message header size is of 1 byte, with
no padding bits.
For the All-1 message to be distinguishable from the Sender-Abort
message, the Sender-Abort message MUST be of 1 byte (only header with
no padding). This way, the minimum size of the All-1 is 2 bytes, and
the Sender-Abort message is 1 byte.
3.7.1.3. SCHC ACK Format
Figure 5 shows the SCHC ACK format when all fragments have been
correctly received (C=1). Padding MUST be added to complete the
64-bit Sigfox downlink frame payload size.
|---- SCHC ACK Header ----|
+ ----------------------- + ------- +
| RuleID | W | C=b'1 | b'0-pad |
+ ------ + ------ + ----- + ------- +
| 3 bits | 2 bits | 1 bit | 58 bits |
Figure 5: SCHC Success ACK message format
Zuniga, et al. Expires January 10, 2022 [Page 13]
Internet-Draft SCHC over Sigfox LPWAN July 2021
In case SCHC fragment losses are found in any of the windows of the
SCHC Packet (C=0), the SCHC Compound ACK defined in
[I-D.ietf-lpwan-schc-compound-ack] MUST be used. The SCHC Compound
ACK message format is shown in Figure 6. The window numbered 00, if
present in the SCHC Compound ACK, MUST be placed between the Rule ID
and the C bit to avoid confusion with padding bits. As padding is
needed for the SCHC Compound ACK, padding bits MUST be 0 to make
subsequent window numbers and bitmaps distinguishable.
|---- SCHC ACK Header ----|-W = x -|...| --- W = x + i ---|
+ ----------------------- + ------ +...+ ------- + ------ + ------- +
| RuleID | W=b'x | C=b'0 | Bitmap |...| W=b'x+i | Bitmap | b'0-pad |
+ ------ + ------ + ----- + ------ +...+ ------- + ------ + ------- +
| 3 bits | 2 bits | 1 bit | 7 bits | | 2 bits | 7 bits |
On top are noted the window number of the corresponding bitmap.
Losses are found in windows x,...,x+i.
Figure 6: SCHC Compound ACK message format
The following figures show examples of the SCHC Compound ACK message
format, when used on SCHC over Sigfox.
|---- SCHC ACK Header ----|- W=00 -|----- W=01 ------|
+ ----------------------- + ------ + ------ + ------ + ------- +
| RuleID | W=b'00 | C=b'0 | Bitmap | W=b'01 | Bitmap | b'0-pad |
+ ------ + ------ + ----- + ------ + ------ + ------ + ------- +
| 3 bits | 2 bits | 1 bit | 7 bits | 2 bits | 7 bits | 42 bits |
Losses are found in windows 00 and 01.
Figure 7: SCHC Compound ACK example 1
|---- SCHC ACK Header ----|- W=01 -|----- W=11 ------|
+ ----------------------- + ------ + ------ + ------ + ------- +
| RuleID | W=b'01 | C=b'0 | Bitmap | W=b'11 | Bitmap | b'0-pad |
+ ------ + ------ + ----- + ------ + ------ + ------ + ------- +
| 3 bits | 2 bits | 1 bit | 7 bits | 2 bits | 7 bits | 42 bits |
Losses are found in windows 01 and 11.
Figure 8: SCHC Compound ACK example 2
Zuniga, et al. Expires January 10, 2022 [Page 14]
Internet-Draft SCHC over Sigfox LPWAN July 2021
|---- SCHC ACK Header ----|- W=00 -|----- W=10 ------|
+ ----------------------- + ------ + ------ + ------ + ------- +
| RuleID | W=b'00 | C=b'0 | Bitmap | W=b'10 | Bitmap | b'0-pad |
+ ------ + ------ + ----- + ------ + ------ + ------ + ------- +
| 3 bits | 2 bits | 1 bit | 7 bits | 2 bits | 7 bits | 42 bits |
Losses are found in windows 00 and 10.
Figure 9: SCHC Compound ACK example 3
Figure 10 shows the SCHC Compound ACK message format when losses are
found in all windows. The window numbers and its corresponding
bitmaps are ordered from window numbered 00 to 11, notifying all four
possible windows.
|- SCHC ACK Header -|W=b'00|-- W=b'01 ---|
+-------------------+------+ ---- +------+
|RuleID|W=b'00|C=b'0|Bitmap|W=b'01|Bitmap| ...
+------+------+-----+------+------+------+
|3 bits|2 bits|1 bit|7 bits|2 bits|7 bits|
|--- W=b'10 --|--- W=b'11 --|
|------+------+------+------+-------+
... |W=b'10|Bitmap|W=b'11|Bitmap|b'0-pad|
|------+------+------+------+-------+
|2 bits|7 bits|2 bits|7 bits|24 bits|
Losses are found in windows 00, 01, 10 and 11.
Figure 10: SCHC Compound ACK example 4
|- SCHC ACK Header -|W=b'00|-- W=b'01 ---|--- W=b'10 --|
+-------------------+------+------+------+------+------+-------+
|RuleID|W=b'00|C=b'0|Bitmap|W=b'01|Bitmap|W=b'10|Bitmap|b'0-pad|
+------+------+-----+------+------+------+------+------+-------+
|3 bits|2 bits|1 bit|7 bits|2 bits|7 bits|2 bits|7 bits|33 bits|
Losses are found in windows 00, 01 and 10.
Figure 11: SCHC Compound ACK example 5
Zuniga, et al. Expires January 10, 2022 [Page 15]
Internet-Draft SCHC over Sigfox LPWAN July 2021
3.7.1.4. SCHC Sender-Abort Message format
|---- Sender-Abort Header ----|
+ --------------------------- +
| RuleID | W | FCN=ALL-1 |
+ ------ + ------ + --------- +
| 3 bits | 2 bits | 3 bits |
Figure 12: SCHC Sender-Abort message format
3.7.1.5. SCHC Receiver-Abort Message format
|- Receiver-Abort Header -|
+ ----------------------- + ------- +
| RuleID | W=b'11 | C=b'1 | b'1-pad |
+ ------ + ------ + ----- + ------- +
| 3 bits | 2 bits | 1 bit | 58 bits |
Figure 13: SCHC Receiver-Abort message format
3.7.2. Uplink ACK-on-Error Mode: Two-byte SCHC Header
3.7.2.1. Regular SCHC Fragment
Figure 14 shows an example of a regular SCHC fragment for all
fragments except the last one. The penultimate tile of a SCHC Packet
is of the regular size.
|-- SCHC Fragment Header --|
+ ------------------------ + ------- +
| RuleID | W | FCN | Payload |
+ ------ + ------ + ------ + ------- +
| 8 bits | 3 bits | 5 bits | 80 bits |
Figure 14: Regular SCHC Fragment format for all fragments except the
last one
The use of SCHC ACK is NOT RECOMMENDED, instead the All-1 SCHC
Fragment SHOULD be used to request a SCHC ACK from the receiver
(Network SCHC). As per [RFC8724], the All-0 message is
distinguishable from the SCHC ACK REQ (All-1 message).
Zuniga, et al. Expires January 10, 2022 [Page 16]
Internet-Draft SCHC over Sigfox LPWAN July 2021
3.7.2.2. All-1 SCHC Fragment
Figure 15 shows an example of the All-1 message. The All-1 message
MUST contain the last tile of the SCHC Packet.
|--- SCHC Fragment Header ---|
+ --------------------------- + ------------ +
| RuleID | W | FCN=ALL-1 | Payload |
+ ------ + ------ + --------- + ------------ +
| 8 bits | 3 bits | 5 bits | 8 to 80 bits |
Figure 15: All-1 SCHC message format with last tile
As per [RFC8724] the All-1 must be distinguishable from the a SCHC
Sender-Abort message (with same Rule ID, M and N values). The All-1
MUST have the last tile of the SCHC Packet, that MUST be of at least
1 byte. The SCHC Sender-Abort message header size is of 2 byte, with
no padding bits.
For the All-1 message to be distinguishable from the Sender-Abort
message, the Sender-Abort message MUST be of 2 byte (only header with
no padding). This way, the minimum size of the All-1 is 3 bytes, and
the Sender-Abort message is 2 bytes.
3.7.2.3. SCHC ACK Format
Figure 16 shows the SCHC ACK format when all fragments have been
correctly received (C=1). Padding MUST be added to complete the
64-bit Sigfox downlink frame payload size.
|----- SCHC ACK Header ----|
+ ------------------------ + ------ +
| RuleID | W | C=b'1 | b'0-pad |
+ ------ + ------ + ----- + ------- +
| 8 bits | 3 bits | 1 bit | 52 bits |
Figure 16: SCHC Success ACK message format
The SCHC Compound ACK message MUST be used in case SCHC fragment
losses are found in any window of the SCHC Packet (C=0). The SCHC
Compound ACK message format is shown in Figure 17. The SCHC Compound
ACK can report up to 3 windows with losses. The window number (W)
and its corresponding bitmap MUST be ordered from the lowest-numbered
window number to the highest-numbered window. If window numbered 000
Zuniga, et al. Expires January 10, 2022 [Page 17]
Internet-Draft SCHC over Sigfox LPWAN July 2021
is present in the SCHC Compound ACK, the window number 000 MUST be
placed between the Rule ID and C bit to avoid confusion with padding
bits. The SCHC Compound ACK MUST be 0 padded (Padding bits must be
0).
|- SCHC ACK Header -| W=b'x |...|--- W=b'x+i ---|
+-------------------+-------+...+-------+-------+-------+
|RuleID|W=b'x |C=b'0|Bitmap |...|W=b'x+i|Bitmap |b'0-pad|
+------+------+-----+-------+...|-------+-------+-------+
|8 bits|3 bits|1 bit|31 bits| | 3 bits|31 bits|
On top are noted the window number
of the corresponding bitmap.
Losses are found in windows x,...,x+i.
Figure 17: SCHC Compound ACK message format
3.7.2.4. SCHC Sender-Abort Messages
|---- Sender-Abort Header ----|
+ --------------------------- +
| RuleID | W | FCN=ALL-1 |
+ ------ + ------ + --------- +
| 8 bits | 3 bits | 5 bits |
Figure 18: SCHC Sender-Abort message format
3.7.2.5. SCHC Receiver-Abort Message
|-- Receiver-Abort Header -|
+ ------------------------ + ------- +
| RuleID | W=b'111 | C=b'1 | b'1-pad |
+ ------ + ------- + ----- + ------- +
| 8 bits | 3 bits | 1 bit | 52 bits |
Figure 19: SCHC Receiver-Abort message format
3.8. Padding
The Sigfox payload fields have different characteristics in uplink
and downlink.
Zuniga, et al. Expires January 10, 2022 [Page 18]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Uplink frames can contain a payload size from 0 to 12 bytes. The
Sigfox radio protocol allows sending zero bits, one single bit of
information for binary applications (e.g. status), or an integer
number of bytes. Therefore, for 2 or more bits of payload it is
required to add padding to the next integer number of bytes. The
reason for this flexibility is to optimize transmission time and
hence save battery consumption at the device.
Downlink frames on the other hand have a fixed length. The payload
length MUST be 64 bits (i.e. 8 bytes). Hence, if less information
bits are to be transmitted, padding MUST be used with bits equal to
0.
4. Fragmentation Sequence Examples
In this section, some sequence diagrams depicting messages exchanges
for different fragmentation modes and use cases are shown. In the
examples, 'Seq' indicates the Sigfox Sequence Number of the frame
carrying a fragment.
4.1. Uplink No-ACK Examples
The FCN field indicates the size of the data packet. The first
fragment is marked with FCN = X-1, where X is the number of fragments
the message is split into. All fragments are marked with decreasing
FCN values. Last packet fragment is marked with the FCN = All-1
(1111).
Case No losses - All fragments are sent and received successfully.
Sender Receiver
|-------FCN=6 (0110), Seq=1-------->|
|-------FCN=5 (0101), Seq=2-------->|
|-------FCN=4 (0100), Seq=3-------->|
|-------FCN=3 (0011), Seq=4-------->|
|-------FCN=2 (0010), Seq=5-------->|
|-------FCN=1 (0001), Seq=6-------->|
|-------FCN=15 (1111), Seq=7------->| All fragments received
(End)
Figure 20: UL No-ACK No-Losses
When the first SCHC fragment is received, the Receiver can calculate
the total number of SCHC fragments that the SCHC Packet is composed
Zuniga, et al. Expires January 10, 2022 [Page 19]
Internet-Draft SCHC over Sigfox LPWAN July 2021
of. For example, if the first fragment is numbered with FCN=6, the
receiver can expect six more messages/fragments (i.e., with FCN going
from 5 downwards, and the last fragment with a FCN equal to 15).
Case losses on any fragment except the first.
Sender Receiver
|-------FCN=6, Seq=1-------->|
|-------FCN=5, Seq=2----X--->|
|-------FCN=4, Seq=3-------->|
|-------FCN=3, Seq=4-------->|
|-------FCN=2, Seq=5-------->|
|-------FCN=1, Seq=6-------->|
|-------FCN=15, Seq=7------->| Missing Fragment - Unable to reassemble
(End)
Figure 21: UL No-ACK Losses (scenario 1)
4.2. Uplink ACK-on-Error Examples: Single-byte SCHC Header
The single-byte SCHC header ACK-on-Error mode allows sending up to 28
fragments and packet sizes up to 300 bytes. The SCHC fragments may
be delivered asynchronously and DL ACK can be sent opportunistically.
Case No losses
The downlink flag must be enabled in the sender UL message to allow a
DL message from the receiver. The DL Enable in the figures shows
where the sender should enable the downlink, and wait for an ACK.
Zuniga, et al. Expires January 10, 2022 [Page 20]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2----->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7----->|
(no ACK)
|-----W=1, FCN=6, Seq=8----->|
|-----W=1, FCN=5, Seq=9----->|
|-----W=1, FCN=4, Seq=10---->|
DL Enable |-----W=1, FCN=7, Seq=11---->| All fragments received
|<------ ACK, W=1, C=1 ------| C=1
(End)
Figure 22: UL ACK-on-Error No-Losses
Case Fragments lost in first window
In this case, fragments are lost in the first window (W=0). After
the first All-0 message arrives, the Receiver leverages the
opportunity and sends an ACK with the corresponding bitmap and C=0.
After the missing fragments from the first window (W=0) are resent,
the sender continues transmitting the fragments of the following
window (W=1) without opening a reception opportunity. Finally, the
All-1 fragment is sent, the downlink is enabled, and the ACK is
received with C=1.
Zuniga, et al. Expires January 10, 2022 [Page 21]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2--X-->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5--X-->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7----->| Missing Fragments W=0 => FCN=5, Seq=2 and FCN=2, Seq=5
|<------ ACK, W=0, C=0 ------| Bitmap:1011011
|-----W=0, FCN=5, Seq=8----->|
|-----W=0, FCN=2, Seq=9----->|
|-----W=1, FCN=6, Seq=10---->|
|-----W=1, FCN=5, Seq=11---->|
|-----W=1, FCN=4, Seq=12---->|
DL Enable |-----W=1, FCN=7, Seq=13---->| All fragments received
|<------ ACK, W=1, C=1 ------| C=1
(End)
Figure 23: UL ACK-on-Error Losses on First Window
Case Fragments All-0 lost in first window (W=0)
In this example, the All-0 of the first window (W=0) is lost.
Therefore, the Receiver waits for the next All-X message to generate
the corresponding ACK, notifying the absence of the All-0 of window
0.
The sender resends the missing All-0 messages (with any other missing
fragment from window 0). Note that this behaviour can take place in
any intermediate window if the All-0 message is lost.
Zuniga, et al. Expires January 10, 2022 [Page 22]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2----->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->| DL Enable
|-----W=0, FCN=0, Seq=7--X-->|
(no ACK)
|-----W=1, FCN=6, Seq=8----->|
|-----W=1, FCN=5, Seq=9----->|
|-----W=1, FCN=4, Seq=10---->|
DL Enable |-----W=1, FCN=7, Seq=11---->| Missing Fragment W=0, FCN=0, Seq=7
|<------ ACK, W=0, C=0 ------| Bitmap:1111110
|-----W=0, FCN=0, Seq=13---->| All fragments received
DL Enable |-----W=1, FCN=7, Seq=14---->|
|<------ ACK, W=1, C=1 ------| C=1
(End)
Figure 24: UL ACK-on-Error All-0 Lost on First Window
In the following diagram, besides the All-0 there are other lost
fragments in the first window (W=0).
Zuniga, et al. Expires January 10, 2022 [Page 23]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2--X-->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4--X-->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7--X-->|
(no ACK)
|-----W=1, FCN=6, Seq=8----->|
|-----W=1, FCN=5, Seq=9----->|
|-----W=1, FCN=4, Seq=10---->|
DL Enable |-----W=1, FCN=7, Seq=11---->| Missing Fragment W=0 => FCN= 5, 3 and 0
|<------ ACK, W=0, C=0 ------| Bitmap:1010110
|-----W=0, FCN=5, Seq=13---->|
|-----W=0, FCN=3, Seq=14---->|
|-----W=0, FCN=0, Seq=15---->| All fragments received
DL Enable |-----W=1, FCN=7, Seq=16---->|
|<------ ACK, W=1, C=1 ------| C=1
(End)
Figure 25: UL ACK-on-Error All-0 and other Fragments Lost on First
Window
In the next examples, there are losses in both the first (W=0) and
second (W=1) windows. The retransmission cycles after the All-1 is
sent (i.e., not in intermediate windows) should always finish with an
with an All-1. In case an intermediate All-0 is lost and then
retransmitted, the All-1 is resent after, as it serves as an ACK
Request message to confirm the correct reception of the retransmitted
fragments.
Zuniga, et al. Expires January 10, 2022 [Page 24]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6 (110), Seq=1----->|
|-----W=0, FCN=5 (101), Seq=2--X-->|
|-----W=0, FCN=4 (100), Seq=3----->|
|-----W=0, FCN=3 (011), Seq=4--X-->|
|-----W=0, FCN=2 (010), Seq=5----->|
|-----W=0, FCN=1 (001), Seq=6----->|
DL enable |-----W=0, FCN=0 (000), Seq=7--X-->|
(no ACK)
|-----W=1, FCN=6 (110), Seq=8--X-->|
|-----W=1, FCN=5 (101), Seq=9----->|
|-----W=1, FCN=4 (011), Seq=10-X-->|
DL enable |-----W=1, FCN=7 (111), Seq=11---->| Missing Fragment W=0 => FCN= 5, 3 and 0
|<--------- ACK, W=0, C=0 ---------| Bitmap:1010110
|-----W=0, FCN=5 (101), Seq=13---->|
|-----W=0, FCN=3 (011), Seq=14---->|
|-----W=0, FCN=0 (000), Seq=15---->|
DL enable |-----W=1, FCN=7 (111), Seq=16---->| Missing Fragment W=1 => FCN= 6 and 4
|<--------- ACK, W=1, C=0 ---------| Bitmap:0100001
|-----W=1, FCN=6 (110), Seq=18---->|
|-----W=1, FCN=4 (011), Seq=19---->| All fragments received
DL enable |-----W=1, FCN=7 (111), Seq=20---->|
|<--------- ACK, W=1, C=1 ---------| C=1
(End)
Figure 26: UL ACK-on-Error All-0 and other Fragments Lost on First
and Second Windows (1)
Similar case as above, but with less fragments in the second window
(W=1)
Zuniga, et al. Expires January 10, 2022 [Page 25]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6 (110), Seq=1----->|
|-----W=0, FCN=5 (101), Seq=2--X-->|
|-----W=0, FCN=4 (100), Seq=3----->|
|-----W=0, FCN=3 (011), Seq=4--X-->|
|-----W=0, FCN=2 (010), Seq=5----->|
|-----W=0, FCN=1 (001), Seq=6----->|
DL enable |-----W=0, FCN=0 (000), Seq=7--X-->|
(no ACK)
|-----W=1, FCN=6 (110), Seq=8--X-->|
DL enable |-----W=1, FCN=7 (111), Seq=9----->| Missing Fragment W=0 => FCN= 5, 3 and 0
|<--------- ACK, W=0, C=0 ---------| Bitmap:1010110
|-----W=0, FCN=5 (101), Seq=10---->|
|-----W=0, FCN=3 (011), Seq=11---->|
DL enable |-----W=0, FCN=0 (000), Seq=12---->| Missing Fragment W=1 => FCN= 6 and 4
|<--------- ACK, W=1, C=0 ---------| Bitmap:0000001
|-----W=1, FCN=6 (110), Seq=15---->| All fragments received
DL enable |-----W=1, FCN=7 (111), Seq=17---->|
|<--------- ACK, W=1, C=1 ---------| C=1
(End)
Figure 27: UL ACK-on-Error All-0 and other Fragments Lost on First
and Second Windows (2)
Case ACK is lost
SCHC over Sigfox does not implement the SCHC ACK REQ message.
Instead it uses the SCHC All-1 message to request an ACK, when
required.
Zuniga, et al. Expires January 10, 2022 [Page 26]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2----->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7----->|
(no ACK)
|-----W=1, FCN=6, Seq=8----->|
|-----W=1, FCN=5, Seq=9----->|
|-----W=1, FCN=4, Seq=10---->|
DL Enable |-----W=1, FCN=7, Seq=11---->| All fragments received
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=13---->| RESEND ACK
|<------ ACK, W=1, C=1 ------| C=1
(End)
Figure 28: UL ACK-on-Error ACK Lost
The number of times an ACK will be requested is determined by the
MAX_ACK_REQUESTS.
4.3. SCHC Abort Examples
Case SCHC Sender-Abort
The sender may need to send a Sender-Abort to stop the current
communication. This may happen, for example, if the All-1 has been
sent MAX_ACK_REQUESTS times.
Zuniga, et al. Expires January 10, 2022 [Page 27]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2----->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7----->|
(no ACK)
|-----W=1, FCN=6, Seq=8----->|
|-----W=1, FCN=5, Seq=9----->|
|-----W=1, FCN=4, Seq=10---->|
DL Enable |-----W=1, FCN=7, Seq=11---->| All fragments received
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=14---->| RESEND ACK (1)
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=15---->| RESEND ACK (2)
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=16---->| RESEND ACK (3)
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=17---->| RESEND ACK (4)
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |-----W=1, FCN=7, Seq=18---->| RESEND ACK (5)
|<------ ACK, W=1, C=1 ---X--| C=1
DL Enable |----Sender-Abort, Seq=19--->| exit with error condition
(End)
Figure 29: UL ACK-on-Error Sender-Abort
Case Receiver-Abort
The reciever may need to send a Receiver-Abort to stop the current
communication. This message can only be sent after a DL enable.
Zuniga, et al. Expires January 10, 2022 [Page 28]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sender Receiver
|-----W=0, FCN=6, Seq=1----->|
|-----W=0, FCN=5, Seq=2----->|
|-----W=0, FCN=4, Seq=3----->|
|-----W=0, FCN=3, Seq=4----->|
|-----W=0, FCN=2, Seq=5----->|
|-----W=0, FCN=1, Seq=6----->|
DL Enable |-----W=0, FCN=0, Seq=7----->|
|<------- RECV ABORT -------| under-resourced
(Error)
Figure 30: UL ACK-on-Error Receiver-Abort
5. Security considerations
The radio protocol authenticates and ensures the integrity of each
message. This is achieved by using a unique device ID and an AES-128
based message authentication code, ensuring that the message has been
generated and sent by the device with the ID claimed in the message.
Application data can be encrypted at the application level or not,
depending on the criticality of the use case. This flexibility
allows providing a balance between cost and effort vs. risk. AES-128
in counter mode is used for encryption. Cryptographic keys are
independent for each device. These keys are associated with the
device ID and separate integrity and confidentiality keys are pre-
provisioned. A confidentiality key is only provisioned if
confidentiality is to be used.
The radio protocol has protections against reply attacks, and the
cloud-based core network provides firewalling protection against
undesired incoming communications.
6. Acknowledgements
Carles Gomez has been funded in part by the Spanish Government
through the Jose Castillejo CAS15/00336 grant, the TEC2016-79988-P
grant, and the PID2019-106808RA-I00 grant, and by Secretaria
d'Universitats i Recerca del Departament d'Empresa i Coneixement de
la Generalitat de Catalunya 2017 through grant SGR 376.
Sergio Aguilar has been funded by the ERDF and the Spanish Government
through project TEC2016-79988-P and project PID2019-106808RA-I00,
AEI/FEDER, EU.
Zuniga, et al. Expires January 10, 2022 [Page 29]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Sandra Cespedes has been funded in part by the ANID Chile Project
FONDECYT Regular 1201893 and Basal Project FB0008.
Diego Wistuba has been funded by the ANID Chile Project FONDECYT
Regular 1201893.
The authors would like to thank Clement Mannequin, Rafael Vidal,
Julien Boite, Renaud Marty, and Antonis Platis for their useful
comments and implementation design considerations.
7. References
7.1. Normative References
[I-D.ietf-lpwan-schc-compound-ack]
Zuniga, JC., Gomez, C., Aguilar, S., Toutain, L.,
Cespedes, S., and D. Wistuba, "SCHC Compound ACK", draft-
ietf-lpwan-schc-compound-ack-00 (work in progress), July
2021.
[RFC8376] Farrell, S., Ed., "Low-Power Wide Area Network (LPWAN)
Overview", RFC 8376, DOI 10.17487/RFC8376, May 2018,
<https://www.rfc-editor.org/info/rfc8376>.
[RFC8724] Minaburo, A., Toutain, L., Gomez, C., Barthel, D., and JC.
Zuniga, "SCHC: Generic Framework for Static Context Header
Compression and Fragmentation", RFC 8724,
DOI 10.17487/RFC8724, April 2020,
<https://www.rfc-editor.org/info/rfc8724>.
7.2. Informative References
[sigfox-callbacks]
Sigfox, "Sigfox Callbacks",
<https://support.sigfox.com/docs/callbacks-documentation>.
[sigfox-spec]
Sigfox, "Sigfox Radio Specifications",
<https://build.sigfox.com/sigfox-device-radio-
specifications>.
Authors' Addresses
Zuniga, et al. Expires January 10, 2022 [Page 30]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Juan Carlos Zuniga
SIGFOX
Montreal QC
Canada
Email: JuanCarlos.Zuniga@sigfox.com
URI: http://www.sigfox.com/
Carles Gomez
Universitat Politecnica de Catalunya
C/Esteve Terradas, 7
08860 Castelldefels
Spain
Email: carlesgo@entel.upc.edu
Sergio Aguilar
Universitat Politecnica de Catalunya
C/Esteve Terradas, 7
08860 Castelldefels
Spain
Email: sergio.aguilar.romero@upc.edu
Laurent Toutain
IMT-Atlantique
2 rue de la Chataigneraie
CS 17607
35576 Cesson-Sevigne Cedex
France
Email: Laurent.Toutain@imt-atlantique.fr
Sandra Cespedes
NIC Labs, Universidad de Chile
Av. Almte. Blanco Encalada 1975
Santiago
Chile
Email: scespedes@niclabs.cl
Zuniga, et al. Expires January 10, 2022 [Page 31]
Internet-Draft SCHC over Sigfox LPWAN July 2021
Diego Wistuba
NIC Labs, Universidad de Chile
Av. Almte. Blanco Encalada 1975
Santiago
Chile
Email: wistuba@niclabs.cl
Zuniga, et al. Expires January 10, 2022 [Page 32]