Mobile Ad hoc Networks Working Group C. Perkins
Internet-Draft Futurewei
Intended status: Standards Track S. Ratliff
Expires: August 8, 2014 Cisco
J. Dowdell
Cassidian
February 4, 2014
Dynamic MANET On-demand (AODVv2) Routing
draft-ietf-manet-aodvv2-03
Abstract
The revised Ad Hoc On-demand Distance Vector (AODVv2) routing
protocol is intended for use by mobile routers in wireless, multihop
networks. AODVv2 determines unicast routes among AODVv2 routers
within the network in an on-demand fashion, offering on-demand
convergence in dynamic topologies.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 8, 2014.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Perkins, et al. Expires August 8, 2014 [Page 1]
Internet-Draft AODVv2 February 2014
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Notational Conventions . . . . . . . . . . . . . . . . . . . 7
4. Applicability Statement . . . . . . . . . . . . . . . . . . . 7
5. Data Structures . . . . . . . . . . . . . . . . . . . . . . . 9
5.1. Route Table Entry . . . . . . . . . . . . . . . . . . . . 9
5.2. Bidirectional Connectivity and Blacklists . . . . . . . . 11
5.3. Router Clients and Client Networks . . . . . . . . . . . 11
5.4. AODVv2 Packet Header Fields and Information Elements . . 12
5.5. Sequence Numbers . . . . . . . . . . . . . . . . . . . . 13
5.6. Enabling Alternate Metrics . . . . . . . . . . . . . . . 14
5.7. RREQ Table: Received RREQ Messages . . . . . . . . . . . 16
6. AODVv2 Operations on Route Table Entries . . . . . . . . . . 17
6.1. Evaluating Incoming Routing Information . . . . . . . . . 17
6.2. Applying Route Updates To Route Table Entries . . . . . . 19
6.3. Route Table Entry Timeouts . . . . . . . . . . . . . . . 19
7. Routing Messages RREQ and RREP (RteMsgs) . . . . . . . . . . 20
7.1. Route Discovery Retries and Buffering . . . . . . . . . . 20
7.2. RteMsg Structure . . . . . . . . . . . . . . . . . . . . 21
7.3. RREQ Generation . . . . . . . . . . . . . . . . . . . . . 23
7.4. RREP Generation . . . . . . . . . . . . . . . . . . . . . 24
7.5. Handling a Received RteMsg . . . . . . . . . . . . . . . 24
7.5.1. Additional Handling for Incoming RREQ . . . . . . . . 25
7.5.2. Additional Handling for Incoming RREP . . . . . . . . 26
7.6. Suppressing Redundant RREQ messages . . . . . . . . . . . 27
8. Route Maintenance and RERR Messages . . . . . . . . . . . . . 27
8.1. Maintaining Route Lifetimes During Packet Forwarding . . 27
8.2. Active Next-hop Router
Adjacency Monitoring . . . . . . . . . . . . . . . . . . 28
8.3. RERR Generation . . . . . . . . . . . . . . . . . . . . . 28
8.3.1. Case 1: Undeliverable Packet . . . . . . . . . . . . 29
8.3.2. Case 2: Broken Link . . . . . . . . . . . . . . . . . 30
8.4. Receiving and Handling RERR Messages . . . . . . . . . . 30
9. Unknown Message and TLV Types . . . . . . . . . . . . . . . . 32
10. Simple Internet Attachment . . . . . . . . . . . . . . . . . 32
11. Multiple Interfaces . . . . . . . . . . . . . . . . . . . . . 33
12. AODVv2 Control Packet/Message Generation Limits . . . . . . . 33
13. Optional Features . . . . . . . . . . . . . . . . . . . . . . 33
13.1. Expanding Rings Multicast . . . . . . . . . . . . . . . 34
13.2. Intermediate RREP . . . . . . . . . . . . . . . . . . . 34
13.3. Precursor Lists and Notifications . . . . . . . . . . . 34
13.3.1. Overview . . . . . . . . . . . . . . . . . . . . . . 34
Perkins, et al. Expires August 8, 2014 [Page 2]
Internet-Draft AODVv2 February 2014
13.3.2. Precursor Notification Details . . . . . . . . . . . 35
13.4. Multicast RREP Response to RREQ . . . . . . . . . . . . 35
13.5. RREP_ACK . . . . . . . . . . . . . . . . . . . . . . . . 36
13.6. Message Aggregation . . . . . . . . . . . . . . . . . . 36
14. Administratively Configurable
Parameters and Timer Values . . . . . . . . . . . . . . . . . 36
14.1. Timers . . . . . . . . . . . . . . . . . . . . . . . . . 36
14.2. Protocol constants . . . . . . . . . . . . . . . . . . . 37
14.3. Administrative (functional) controls . . . . . . . . . . 37
14.4. Other administrative parameters and lists . . . . . . . 38
15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 38
15.1. AODVv2 Message Types Specification . . . . . . . . . . . 38
15.2. Message TLV Type Specification . . . . . . . . . . . . . 39
15.3. Address Block TLV Specification . . . . . . . . . . . . 39
15.4. Metric Type Number Allocation . . . . . . . . . . . . . 40
16. Security Considerations . . . . . . . . . . . . . . . . . . . 40
17. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 42
18. References . . . . . . . . . . . . . . . . . . . . . . . . . 42
18.1. Normative References . . . . . . . . . . . . . . . . . . 42
18.2. Informative References . . . . . . . . . . . . . . . . . 43
Appendix A. Example RFC 5444-compliant packet formats . . . . . 44
A.1. RREQ Message Format . . . . . . . . . . . . . . . . . . . 44
A.2. RREP Message Format . . . . . . . . . . . . . . . . . . . 46
A.3. RERR Message Format . . . . . . . . . . . . . . . . . . . 48
A.4. RREP_ACK Message Format . . . . . . . . . . . . . . . . . 49
Appendix B. Changes since revision ...-02.txt . . . . . . . . . 49
Appendix C. Shifting Network Prefix Advertisement Between AODVv2
Routers . . . . . . . . . . . . . . . . . . . . . . 50
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 50
1. Overview
The revised Ad Hoc On-demand Distance Vector (AODVv2) routing
protocol [formerly named DYMO] enables on-demand, multihop unicast
routing among AODVv2 routers in mobile ad hod networks
[MANETs][RFC2501]. The basic operations of the AODVv2 protocol are
route discovery and route maintenance. Route discovery is performed
when an AODVv2 router must transmit a packet towards a destination
for which it does not have a route. Route maintenance is performed
to avoid prematurely expunging routes from the route table, and to
avoid dropping packets when an active route breaks.
During route discovery, the originating AODVv2 router (RREQ_Gen)
multicasts a Route Request message (RREQ) to find a route toward some
target destination. Using a hop-by-hop retransmission algorithm,
each AODVv2 router receiving the RREQ message records a route toward
the originator. When the target's AODVv2 router (RREP_Gen) receives
the RREQ, it records a route toward RREQ_Gen and generates a Route
Perkins, et al. Expires August 8, 2014 [Page 3]
Internet-Draft AODVv2 February 2014
Reply (RREP) unicast toward RREQ_Gen. Each AODVv2 router that
receives the RREP stores a route toward the target, and again
unicasts the RREP toward the originator. When RREQ_Gen receives the
RREP, routes have then been established between RREQ_Gen (the
originating AODVv2 router) and RREP_Gen (the target's AODVv2 router)
in both directions.
Route maintenance consists of two operations. In order to maintain
active routes, AODVv2 routers extend route lifetimes upon
successfully forwarding a packet. When a data packet is received to
be forwarded downstream but there is no valid route for the
destination, then the AODVv2 router of the source of the packet is
notified via a Route Error (RERR) message. Each upstream router that
receives the RERR marks the route as broken. Before such an upstream
AODVv2 router could forward a packet to the same destination, it
would have to perform route discovery again for that destination.
AODVv2 uses sequence numbers to assure loop freedom [Perkins99],
similarly to AODV. Sequence numbers enable AODVv2 routers to
determine the temporal order of AODVv2 route discovery messages,
thereby avoiding use of stale routing information. Unlike AODV,
AODVv2 uses RFC 5444 message and TLV formats.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
This document also uses some terminology from [RFC5444].
This document defines the following terminology:
Adjacency
A bi-directional relationship between neighboring AODVv2 routers
for the purpose of exchanging routing information. Not every pair
of neighboring routers will necessarily form an adjacency.
Neighboring routers may form an adjacency based on various
information or other protocols; for example, exchange of AODVv2
routing messages, other protocols (e.g. NDP [RFC4861] or NHDP
[RFC6130]), or manual configuration. Loss of a routing adjacency
may also be indicated by similar information; monitoring of
adjacencies where packets are being forwarded is required (see
Section 8.2).
AODVv2 Router
An IP addressable device in the ad-hoc network that performs the
AODVv2 protocol operations specified in this document.
Perkins, et al. Expires August 8, 2014 [Page 4]
Internet-Draft AODVv2 February 2014
AODVv2 Sequence Number (SeqNum)
Same as Sequence Number.
Current_Time
The current time as maintained by the AODVv2 router.
Disregard
Ignore for further processing (see Section 5.4), and discard
unless it is required to keep the message in the packet for
purposes of authentication.
Handling Router (HandlingRtr)
HandlingRtr denotes the AODVv2 router receiving and handling an
AODVv2 message.
Incoming Link
A link over which an AODVv2 router has received a message from an
adjacent router.
MANET
A Mobile Ad Hoc Network as defined in [RFC2501].
Node
An IP addressable device in the ad-hoc network. A node may be an
AODVv2 router, or it may be a device in the network that does not
perform any AODVv2 protocol operations. All nodes in this
document are either AODVv2 Routers or else Router Clients.
Originating Node (OrigNode)
The Originating Node is the node that launched the application
requiring communication with the Target Node. If OrigNode is not
itself an AODVv2 router, its AODVv2 router (RREQ_Gen) has the
responsibility to generate a AODVv2 RREQ message on behalf of
OrigNode when necessary to discover a route.
Reactive
A protocol operation is said to be "reactive" if it is performed
only in reaction to specific events. As used in this document,
"reactive" is essentially synonymous with "on-demand".
Routable Unicast IP Address
A routable unicast IP address is a unicast IP address that when
put into the IP.DestinationAddress field is scoped sufficiently to
be forwarded by a router. Globally-scoped unicast IP addresses
and Unique Local Addresses (ULAs) [RFC6549] are examples of
routable unicast IP addresses.
Route Error (RERR)
A RERR message is used to indicate that an AODVv2 router does not
have a route toward one or more particular destinations.
Route Reply (RREP)
A RREP message is used to establish a route between the RREQ
TargetNode and OrigNode, at all the AODVv2 routers between them.
Route Request (RREQ)
An AODVv2 router uses a RREQ message to discover a valid route to
a particular destination address, called the TargetNode. An
AODVv2 router processing a RREQ receives routing information for
the RREQ OrigNode.
Perkins, et al. Expires August 8, 2014 [Page 5]
Internet-Draft AODVv2 February 2014
Router Client
An AODVv2 router may be configured with a list of other IP
addresses and networks which correspond to other non-router nodes
which require the services of the AODVv2 router for route
discovery and maintenance. An AODVv2 router is always its own
client, so that the list of client IP addresses is never empty.
RREP Generating Router (RREP_Gen)
The RREP Generating Router is the AODVv2 router that serves
TargNode. RREP_Gen generates the RREP message to advertise a
route for TargNode.
RREQ Generating Router (RREQ_Gen)
The RREQ Generating Router is the AODVv2 router that serves
OrigNode. RREQ_Gen generates the RREQ message to discover a route
for TargNode.
Sequence Number (SeqNum)
AODVv2 mandates that each AODVv2 router maintain an unsigned
integer known as the router's "Sequence Number". The Sequence
Number guarantees the temporal order of routing information to
maintain loop-free routes, and fulfills the same role as the
"Destination Sequence Number" of DSDV, and as the AODV Sequence
Number in RFC 3561[RFC3561]. The value zero (0) is reserved to
indicate that the Sequence Number for an address is unknown.
Target Node (TargNode)
The Target Node denotes the node for which a route is needed.
Type-Length-Value structure (TLV)
A generic way to represent information as specified in [RFC5444].
Unreachable Node (UnreachableNode)
An UnreachableNode is a node for which a forwarding route is
unknown.
Valid route
A route that can be used for forwarding; in other words a route
that is not Broken or Expired.
Perkins, et al. Expires August 8, 2014 [Page 6]
Internet-Draft AODVv2 February 2014
3. Notational Conventions
This document uses the conventions found in Table 1 to describe
information in the fields from [RFC5444].
+------------------------+------------------------------------------+
| Notation | Information Location and/or Meaning |
+------------------------+------------------------------------------+
| Route[Address] | A route table entry towards Address |
| Route[Address].{field} | A field in a route table entry |
| -- | -- |
| <msg-hop-count> | RFC 5444 Message Header <msg-hop-count> |
| <msg-hop-limit> | RFC 5444 Message Header <msg-hop-limit> |
| AddrBlk | an RFC 5444 Address TLV Block |
| AddrBlk[1] | The first address slot in AddrBlk |
| AddrBlk[N] | The Nth address slot in AddrBlk |
| OrigNdx | The index of OrigNode within the AddrBlk |
| TargNdx | The index of TargNode within the AddrBlk |
| AddrBlk[OrigNode] | AddrBlk[OrigNdx] |
| AddrBlk[TargNode] | AddrBlk[TargNdx] |
| AddrTLV | an RFC 5444 Address Block TLV |
| AddrTLV[1] | the first item in AddrTLV |
| AddrTLV[N] | the Nth item in AddrTLV |
| AddrTLV[OrigNode] | AddrTLV[OrigNdx] |
| AddrTLV[TargNode] | AddrTLV[TargNdx] |
| Metric_TLV | Metric AddrTLV for AddrBlk |
| SeqNum_TLV | Sequence Number AddrTLV for AddrBlk |
| OrigSeqNum_TLV | Originating Node Sequence Number AddrTLV |
| TargSeqNum_TLV | Target Node Sequence Number AddrTLV |
| -- | -- |
| OrigNode | Originating Node |
| RREQ_Gen | AODVv2 router originating an RREQ |
| RREP_Gen | AODVv2 router responding to an RREQ |
| RteMsg | Either RREQ or RREP |
| RteMsg.{field} | Field in RREQ or RREP |
| HandlingRtr | Handling Router |
| TargNode | Target Node |
| UnreachableNode | Unreachable Node |
+------------------------+------------------------------------------+
Table 1
4. Applicability Statement
The AODVv2 routing protocol is designed for stub (i.e., non-transit)
or disconnected (i.e., from the Internet) mobile ad hoc networks
(MANETs). AODVv2 handles a wide variety of mobility patterns by
determining routes on-demand. AODVv2 also handles a wide variety of
Perkins, et al. Expires August 8, 2014 [Page 7]
Internet-Draft AODVv2 February 2014
traffic patterns. In networks with a large number of routers, AODVv2
is best suited for relatively sparse traffic scenarios where any
particular router forwards packets to only a small percentage of the
AODVv2 routers in the network, due to the on-demand nature of route
discovery and route maintenance. AODVv2 supports routers with
multiple interfaces, as long as each interface has its own (unicast
routeable) IP address; the set of all network interfaces supporting
AODVv2 is administratively configured in a list (namely,
AODVv2_INTERFACES).
Although AODVv2 is closely related to AODV [RFC3561], and has some of
the features of DSR [RFC4728], AODVv2 is not interoperable with
either of those other two protocols.
AODVv2 is applicable to memory constrained devices, since little
routing state is maintained in each AODVv2 router. Only routing
information related to routes between active sources and destinations
is maintained, in contrast to proactive routing protocols that
require routing information to all routers within the MANET be
maintained.
In addition to routing for its own local applications, each AODVv2
router can also route on behalf of other non-routing nodes (i.e.,
"hosts", or, in this document, "clients"), reachable via those
interfaces. Each AODVv2 router, if serving router clients other than
itself, is configured with information about the IP addresses of its
clients. No AODVv2 router is required to have information about the
relationship between any other AODVv2 router and its router clients
(see Section 5.3).
The coordination among multiple AODVv2 routers to distribute routing
information correctly for a shared address (i.e. an address that is
advertised and can be reached via multiple AODVv2 routers) is not
described in this document. The AODVv2 router operation of shifting
responsibility for a routing client from one AODVv2 router to another
is mentioned in Appendix C. Address assignment procedures are
entirely out of scope for AODVv2. Any such node which is not itself
an AODVv2 router SHOULD NOT be served by more than one AODVv2 router
at any one time.
Multi-homing is difficult unless the sequence number is expanded to
include the AODVv2 router's IP address as well as SeqNum. Otherwise,
comparing sequence numbers would not work to evaluate freshness.
Even when the IP address is included, there isn't a good way to
compare sequence numbers from different IP addresses, but at least a
handling node can determine whether the two given sequence numbers
are comparable. If the route table can store multiple routes for the
Perkins, et al. Expires August 8, 2014 [Page 8]
Internet-Draft AODVv2 February 2014
same destination, then multi-homing can work with sequence numbers
augmented by IP addresses.
AODVv2 routers perform route discovery to find a route toward a
particular destination. Therefore, AODVv2 routers MUST must be
configured to respond to RREQs for a certain set of addresses. When
AODVv2 is the only protocol interacting with the forwarding table,
AODVv2 MAY be configured to perform route discovery for all unknown
unicast destinations.
AODVv2 only supports bidirectional links. In the case of possible
unidirectional links, either blacklists (see Section 5.2) or other
means (e.g. adjacency establishment with only neighboring routers
that have bidirectional communication as indicated by NHDP [RFC6130])
of assuring and monitoring bi-directionality are recommended.
Otherwise, persistent packet loss or persistent protocol failures
could occur. The cost of bidirectional link L (denoted Cost(L)) may
depend upon the direction across the link for which the cost is
measured. Metric information from incoming AODVv2 messages SHOULD
NOT be used for route table updates unless it has been received over
a link that is bidirectional.
The routing algorithm in AODVv2 may be operated at layers other than
the network layer, using layer-appropriate addresses. The routing
algorithm makes of some persistent state; if there is no persistent
storage available for this state, recovery can impose a performance
penalty (e.g., in case of AODVv2 router reboots).
5. Data Structures
5.1. Route Table Entry
The route table entry is a conceptual data structure.
Implementations may use any internal representation so long as it
provides access to the information specified below.
Conceptually, a route table entry has the following fields:
Route.Address
The (host or network) destination address of the node(s)
associated with the routing table entry
Route.PrefixLength
The length of the netmask/prefix. If the value of the
Route.PrefixLength is less than the length of addresses in the
address family used by the AODVv2 routers, the associated address
is a routing prefix, rather than a host address. A PrefixLength
is stored for every route in the route table.
Route.SeqNum
Perkins, et al. Expires August 8, 2014 [Page 9]
Internet-Draft AODVv2 February 2014
The Sequence Number associated with destination of the route, as
obtained from the last packet that updated the route table entry
associated with a route table entry.
Route.NextHopAddress
An IP address of the adjacent AODVv2 router on the path toward the
Route.Address
Route.NextHopInterface
The interface used to send packets toward the Route.Address
Route.LastUsed
The time that this route was last used
Route.ExpirationTime
The time at which this route must expire
Route.Broken
A flag indicating whether this Route is broken. This flag is set
to true if the next-hop becomes unreachable or in response to
processing to a RERR (see Section 8.4)
Route.MetricType
The type of the metric for the route towards Route.Address
Route.Metric
The cost of the route towards Route.Address
A route table entry (i.e., a route) may be in one of the following
states:
Active
An Active route is in current use for forwarding packets
Idle
An Idle route can be used for forwarding packets, even though it
is not in current use
Expired
After a route has been idle for too long, it expires, and may no
longer be used for forwarding packets
Broken
A route marked as Broken cannot be used for forwarding packets but
still has valid destination sequence number information.
Timed
The expiration of a Timed route is controlled by the
Route.ExpirationTime time of the route table entry (instead of
MAX_IDLETIME). Until that time, a Timed route can be used for
forwarding packets. Afterwards, the route must be Expired (or
expunged).
The route's state determines the operations that can be performed on
the route table entry. During use, an Active route is maintained
continuously by AODVv2 and is considered to remain active as long as
it is used at least once during every ACTIVE_INTERVAL. When a route
is no longer Active, it becomes an Idle route. After an idle route
remains Idle for MAX_IDLETIME, it becomes an Expired route. An
Perkins, et al. Expires August 8, 2014 [Page 10]
Internet-Draft AODVv2 February 2014
Expired route is not used for forwarding, but the sequence number
information can be maintained until the destination sequence number
has had no updates for MAX_SEQNUM_LIFETIME; after that time, old
sequence number information is considered no longer valuable and the
Expired route MUST BE expunged.
MAX_SEQNUM_LIFETIME is the time after a reboot during which an AODVv2
router MUST NOT transmit any routing messages. Thus, if all other
AODVv2 routers expunge routes to the rebooted router after that time
interval, the rebooted AODVv2 router's sequence number will not be
considered stale by any other AODVv2 router in the MANET.
When the link to a route's next hop is broken, the route is marked as
being Broken, and the route may no longer be used.
5.2. Bidirectional Connectivity and Blacklists
To avoid repeated failure of Route Discovery, an AODVv2 router
(HandlingRtr) handling a RREP message SHOULD attempt to verify
connectivity to the next upstream router towards AODVv2 router
originating an RREQ message. This MAY be done by including the
Acknowledgement Request (AckReq) message TLV (see Section 15.2) in
the RREP. Any unicast packet will satisfy the Acknowledgement
Request, for example an ICMP REPLY message. If the verification is
not received within UNICAST_MESSAGE_SENT_TIMEOUT, HandlingRtr SHOULD
put the upstream neighbor in the blacklist. RREQs received from a
blacklisted node, or any node over a link that is known to be
incoming-only, SHOULD NOT be retransmitted by HandlingRtr. However,
the upstream neighbor SHOULD NOT be permanently blacklisted; after a
certain time (MAX_BLACKLIST_TIME), it SHOULD once again be considered
as a viable upstream neighbor for route discovery operations.
For this purpose, a list of blacklisted nodes along with their time
of removal SHOULD be maintained:
Blacklist.Node
The IP address of the node that did not verify bidirectional
connectivity.
Blacklist.RemoveTime
The time at which Blacklist.Node will be removed from the
blacklist.
5.3. Router Clients and Client Networks
An AODVv2 router may offer routing services to other nodes that are
not AODVv2 routers. AODVv2 defines the Sequence Number to be the
same for the AODVv2 router and each of its clients.
Perkins, et al. Expires August 8, 2014 [Page 11]
Internet-Draft AODVv2 February 2014
For this purpose, CLIENT_ADDRESSES must be configured on each AODVv2
router with the following information:
Client IP address
The IP address of the node that requires routing service from the
AODVv2 router.
Client Prefix Length
The length of the routing prefix associated with the client IP
address.
If the Client Prefix Length is not the full length of the Client IP
address, then the prefix defines a Client Network. If an AODVv2
router is configured to serve a Client Network, then the AODVv2
router MUST serve every node that has an address within the range
defined by the routing prefix of the Client Network. The list of
Routing Clients for an AODVv2 router is never empty, since an AODVv2
router is always its own client as well.
5.4. AODVv2 Packet Header Fields and Information Elements
In its default mode of operation, AODVv2 transmits UDP packets using
the parameters for port number and IP protocol specified in [RFC5498]
to carry protocol packets. By default, AODVv2 packets are sent with
the IP destination address set to the link-local multicast address
LL-MANET-Routers [RFC5498] unless otherwise specified. Therefore,
all AODVv2 routers MUST subscribe to LL-MANET-Routers [RFC5498] to
receiving AODVv2 messages. In order to reduce multicast overhead,
retransmitting multicast packets in MANETs SHOULD be done according
to methods specified in [RFC6621]. AODVv2 does not specify which
method should be used to restrict the set of AODVv2 routers that have
the responsibility to retransmit multicast packets. Note that
multicast packets MAY be sent via unicast. For example, this may
occur for certain link-types (non-broadcast media), for manually
configured router adjacencies, or in order to improve robustness.
The IPv4 TTL (IPv6 Hop Limit) field for all packets containing AODVv2
messages is set to 255. If a packet is received with a value other
than 255, any AODVv2 message contained in the packet MUST be
disregarded by AODVv2. This mechanism, known as "The Generalized TTL
Security Mechanism" (GTSM) [RFC5082] helps to assure that packets
have not traversed any intermediate routers.
IP packets containing AODVv2 protocol messages SHOULD be given
priority queuing and channel access.
AODVv2 messages are transmitted in packets that conform to the packet
and message format specified in [RFC5444]. Here is a brief summary
of the format.
Perkins, et al. Expires August 8, 2014 [Page 12]
Internet-Draft AODVv2 February 2014
A packet formatted according to RFC 5444 contains zero or more
messages.
A message contains a message header, message TLV block, and zero
or more address blocks.
Each address block may also have an associated TLV block; this TLV
block may encode multiple TLVs. According to RFC 5444, each such
TLV may itself include an array of values.
If a packet contains only a single AODVv2 message and no packet TLVs,
it need only include a minimal Packet-Header [RFC5444]. The length
of an address (32 bits for IPv4 and 128 bits for IPv6) inside an
AODVv2 message is indicated by the msg-addr-length (MAL) in the msg-
header, as specified in [RFC5444].
When multiple messages are aggregated into a single packet according
to RFC 5444 formatting, and the aggregation of messages is also
authenticated (e.g., with IPsec), and the IP destination is multiple
hops away, it becomes infeasible to delete individual messages. In
such cases, instead of deleting individual messages, they are
maintained in the aggregation of messages, but simply ignored for
further processing. In such cases where individual messages cannot
be deleted, in this document "disregarded" means "ignored".
Otherwise, any such "disregarded" AODVv2 messages SHOULD be deleted
from the aggregated messages in the RFC 5444 packet.
5.5. Sequence Numbers
Sequence Numbers allow AODVv2 routers to evaluate the freshness of
routing information. Each AODVv2 router in the network MUST maintain
its own sequence number. Each RREQ and RREQ generated by an AODVv2
router includes that sequence number. Each AODVv2 router MUST make
sure that its sequence number is unique and monotonically increasing.
This can be achieved by incrementing it with every RREQ or RREP it
generates.
Every router receiving a RREQ or RREP can thus use the Sequence
Number of a RREQ or RREP as information concerning the freshness of
the packet's route update: If the new packet's Sequence Number is
lower than the one already stored in the routing table, its
information is considered stale.
As a consequence, loop freedom is assured.
An AODVv2 router increments its SeqNum as follows. Most of the time,
SeqNum is incremented by simply adding one (1). But when the SeqNum
has the value of the largest possible number representable as a
16-bit unsigned integer (i.e., 65,535), it MUST be incremented by
Perkins, et al. Expires August 8, 2014 [Page 13]
Internet-Draft AODVv2 February 2014
setting to one (1). In other words, the sequence number after 65,535
is 1.
An AODVv2 router SHOULD maintain its SeqNum in persistent storage.
If an AODVv2 router's SeqNum is lost, it MUST take the following
actions to avoid the danger of routing loops. First, the AODVv2
router MUST invalidate all route table entries, by setting
Route.Broken for each entry. Furthermore the AODVv2 router MUST wait
for at least MAX_SEQNUM_LIFETIME before transmitting or
retransmitting any AODVv2 RREQ or RREP messages. If an AODVv2
protocol message is received during this waiting period, the AODVv2
router SHOULD perform normal route table entry updates, but not
forward the message to other nodes. If a data packet is received for
forwarding to another destination during this waiting period, the
AODVv2 router MUST transmit a RERR message indicating that no route
is available. At the end of the waiting period the AODVv2 router
sets its SeqNum to one (1) and begins performing AODVv2 protocol
operations again.
5.6. Enabling Alternate Metrics
AODVv2 route selection in MANETs depends upon associating metric
information with each route table entry. When presented with
candidate route update information, deciding whether to use the
update involves evaluating the metric. Some applications may require
metric information other than Hop Count, which has traditionally been
the default metric associated with routes in MANET. Unfortunately,
it is well known that reliance on Hop Count can cause selection of
the worst possible route in many situations.
It is beyond the scope of this document to describe how applications
specify route selection at the time they launch processing. One
possibility would be to provide a route metric preference as part of
the library routines for opening sockets. In view of the above
considerations, it is important to enable route selection based on
metric information other than Hop Count -- in other words, based on
"alternate metrics". Each such alternate metric measures a "cost" of
using the associated route, and there are many different kinds of
cost (latency, delay, monetary, energy, etc.).
The most significant change when enabling use of alternate metrics is
to require the possibility of multiple routes to the same
destination, where the "cost" of each of the multiple routes is
measured by a different metric. Moreover, the method by which route
updates are tested for usefulness has to be slightly generalized to
depend upon a more abstract method of evaluation which, in this
document, is named "Cost(R)", where 'R' is the route for which the
Cost is to be evaluated. From the above, the route table information
Perkins, et al. Expires August 8, 2014 [Page 14]
Internet-Draft AODVv2 February 2014
for 'R' must always include the type of metric by which Cost(R) is
evaluated, so the metric type does not have to be shown as a distinct
parameter for Cost(R). Since determining loop freedom is known to
depend on comparing the Cost(R) of route update information to the
Cost(R) of an existing stored route using the same metric, AODVv2
must also be able to invoke an abstract routine which in this
document is called "LoopFree(R1, R2)". LoopFree(R1, R2) returns TRUE
when, (under the assumption of nondecreasing SeqNum during Route
Discovery) given that R2 is loop-free and Cost(R2) is the cost of
route R2, Cost(R1) is known to guarantee loop freedom of the route
R1. In this document, LoopFree(R1,R2) will only be invoked for
routes R1 and R2 to the same destination which use the same metric.
Generally, HopCount may still be considered the default metric for
use in MANETs, notwithstanding the above objections. Each metric has
to have a Metric Type, and the Metric Type is allocated by IANA as
specified in [RFC6551]. Each Route has to include the Metric Type as
part of the route table entry for that route. Hop Count has Metric
Type assignment 3. The Cost of a route using Metric Type 3 is simply
the hop count between the router and the destination. For routes R1
and R2 using Metric Type 3, LoopFree (R1, R2) is TRUE when Cost(R2)
<= (Cost(R1) + 1). The specification of Cost(R) and LoopFree(R1,R2)
for metric types other than 3 is beyond the scope of this document.
Whenever an AODV router receives metric information in an incoming
message, the value of the metric is as measured by the transmitting
router, and does not reflect the cost of traversing the incoming
link. In order to simplify the description of storing accrued route
costs in the route table, the Cost() function is also defined to
return the value of traversing a link 'L'. In other words, the
domain of the Cost() function is enlarged to include links as well as
routes. For Metric Type 3, (i.e., the HopCount metric) Cost(L) = 1
for all links. The specification of Cost(L) for metric types other
than 3 is beyond the scope of this document. Whether the argument of
the Cost() function is a link or a route will, in this document,
always be clear. As a natural result of the way routes are looked up
according to conformant metric type, all intermediate routers
handling a RteMsg will assign the same metric type to all metric
information in the RteMsg.
For some metrics, a maximum value is defined, namely MAX_METRIC[i]
where 'i' is the Metric Type. AODVv2 does not store routes that cost
more than MAX_METRIC[i]. MAX_METRIC[3] is defined to be
MAX_HOPCOUNT, where as before 3 is the Metric Type of the HopCount
metric. MAX_HOPCOUNT MUST be larger than the AODVv2 network
diameter. Otherwise, AODVv2 protocol messages may not reach their
intended destinations.
Perkins, et al. Expires August 8, 2014 [Page 15]
Internet-Draft AODVv2 February 2014
5.7. RREQ Table: Received RREQ Messages
Two incoming RREQ messages are considered to be "comparable" if they
were generated by the same AODVv2 router in order to discover a route
for the same destination with the same metric type. According to
that notion of comparability, when RREQ messages are flooded in a
MANET, an AODVv2 router may well receive comparable RREQ messages
from more than one of its neighbors. A router, after receiving an
RREQ message, MUST check against previous RREQs to assure that its
response message would contain information that is not redundant.
Otherwise, multicast RREQs are likely to be retransmitted again and
again with almost no additional benefit, but generating a great deal
of unnecessary signaling traffic and interference.
To avoid transmission of redundant RREQ messages, while still
enabling the proper handling of earlier RREQ messages that may have
somehow been delayed in the network, it is needed for each AODVv2
router to keep a list of the certain information about RREQ messages
which it has recently received.
This list is called the AODVv2 Received RREQ Table -- or, more
briefly, the RREQ Table. Two AODVv2 RREQ messages are comparable if:
o they have the same metric type
o they have the same OrigNode and TargNode addresses
Each entry in the RREQ Table has the following fields:
o Metric Type
o OrigNode address
o TargNode address
o Sequence Number
o Metric
o Timestamp
The RREQ Table is maintained so that no two entries in the RREQ
Table are comparable -- that is, all RREQs represented in the RREQ
Table either have different OrigNode addresses, different TargNode
addresses, or different metric types. If two RREQs have the same
metric type and OrigNode and Targnode addresses, the information from
the one with the older Sequence Number is not needed in the table; in
case they have the same Sequence Number, the one with the greater
Metric value is not needed; in case they have the same Metric as
well, it does not matter which table entry is maintained. Whenever a
RREQ Table entry is updated, its Timestamp field should also be
updated to reflect the Current_Time.
Perkins, et al. Expires August 8, 2014 [Page 16]
Internet-Draft AODVv2 February 2014
When optional multicast RREP (see Section 13.4) is used to enable
selection from among multiple possible return routes, an AODVv2
router can eliminate redundant RREP messages using the analogous
mechanism along with a RREP Table. Nevertheless, the description in
this section only refers to RREQ multicast messages.
Protocol handling of RERR messages eliminates the need for tracking
RERR messages, since the rules for RERR regeneration prevent the
phenomenon of redundant retansmission that affects RREQ and RREP
multicast.
6. AODVv2 Operations on Route Table Entries
In this section, operations are specified for updating the route
table due to timeouts and route updates within AODVv2 messages.
Route update information in AODVv2 messages includes IP addresses,
along with the SeqNum and prefix length associated with each IP
address, and including the Metric measured from the node transmitting
the AODVv2 message to the IP address in the route update. IP
addresses and prefix length are encoded within an RFC 5444 AddrBlk,
and the SeqNum and Metric associated with each address in the AddrBlk
are encoded in RFC 5444 AddrTLVs. In this section, RteMsg is either
RREQ or RREP, RteMsg.Address[i] denotes the [i]th address in an RFC
5444 AddrBlk of the RteMsg. RteMsg.PrefixLength[i] denotes the
associated prefix length for RteMsg.Address[i], and RteMsg.{field}
denotes the corresponding value in the named AddrTLV block associated
with RteMsg.Address[i]. All SeqNum comparisons use signed 16-bit
arithmetic.
6.1. Evaluating Incoming Routing Information
If the incoming RteMsg does not have a Metric Type Message TLV, then
the metric information contained by RteMsg is considered to be of
type DEFAULT_METRIC_TYPE -- which is 3 (for HopCount) unless changed
by administrative action. Whenever an AODVv2 router (HandlingRtr)
handles an incoming RteMsg (i.e., RREQ or RREP), for every relevant
address (RteMsg.Address) in the RteMsg, HandlingRtr searches its
route table to see if there is a route table entry with the same
Metric Type of the RteMsg, matching RteMsg.Address. If not,
HandlingRtr creates a route table entry for RteMsg.Address as
described in Section 6.2. Otherwise, HandlingRtr compares the
incoming routing information in RteMsg against the already stored
routing information in the route table entry (Route) for
RteMsg.Address, as described below.
Suppose Route[RteMsg.Address] uses the same metric type as the
incoming routing information, and the route entry contains
Route.SeqNum, Route.Metric, and Route.Broken. Suppose the incoming
Perkins, et al. Expires August 8, 2014 [Page 17]
Internet-Draft AODVv2 February 2014
routing information for Route.Address is RteMsg.SeqNum and
RteMsg.Metric. Define RteMsg.Cost to be (RteMsg.Metric + Cost(L)),
where L is the incoming link. The incoming routing information is
classified as follows:
1. Stale:: RteMsg.SeqNum < Route.SeqNum :
If RteMsg.SeqNum < Route.SeqNum the incoming information is stale.
Using stale routing information is not allowed, since that might
result in routing loops. HandlingRtr MUST NOT update the route
table entry using the routing information for RteMsg.Address.
2. Unsafe against loops:: (TRUE != LoopFree (RteMsg, Route)) :
If RteMsg is not Stale (as in (1) above), RteMsg.Cost is next
considered to insure loop freedom. If (TRUE != LoopFree (RteMsg,
Route)) (see Section 5.6), then the incoming RteMsg information is
not guaranteed to prevent routing loops, and it MUST NOT be used
to update any route table entry.
3. More costly::
(RteMsg.Cost >= Route.Metric) && (Route.Broken==FALSE)
When RteMsg.SeqNum is the same as in a valid route table entry,
and LoopFree (RteMsg, Route) assures loop freedom, incoming
information still does not offer any improvement over the existing
route table information if RteMsg.Cost >= Route.Metric. Using
such incoming routing information to update a route table entry is
not recommended.
4. Offers improvement::
Incoming routing information that does not match any of the above
criteria is better than existing routing table information and
SHOULD be used to improve the route table. The following pseudo-
code illustrates whether incoming routing information should be
used to update an existing route table entry as described in
Section 6.2.
(RteMsg.SeqNum > Route.SeqNum) OR
{(RteMsg.SeqNum == Route.SeqNum) AND
[(RteMsg.Cost < Route.Metric) OR
((Route.Broken == TRUE) && LoopFree (RteMsg, Route))]}
The above logic corresponds to placing the following conditions on
the incoming route update (compared to the existing route table
entry) before it can be used:
* it is more recent, or
* it is not stale and is less costly, or
* it can safely repair a broken route.
Perkins, et al. Expires August 8, 2014 [Page 18]
Internet-Draft AODVv2 February 2014
6.2. Applying Route Updates To Route Table Entries
To apply the route update, a route table entry for RteMsg.Address is
either found to already exist in the route table, or else a new route
table entry for RteMsg.Address is created and inserted into the route
table. The route table entry is populated with the following
information:
o If RteMsg.PrefixLength exists, then Route.PrefixLength :=
RteMsg.PrefixLength. Otherwise, Route.PrefixLength := maximum
length for address family (either 32 or 128).
o Route.SeqNum := RteMsg.SeqNum
o Route.NextHopAddress := IP.SourceAddress (i.e., an address of the
node from which the RteMsg was received)
o Route.NextHopInterface is set to the interface on which RteMsg was
received
o Route.Broken flag := FALSE
o If RteMsg.MetricType is included, then
Route.MetricType := RteMsg.MetricType. Otherwise,
Route.MetricType := DEFAULT_METRIC_TYPE.
o Route.Metric := (RteMsg.Metric + Cost(L)), where L is the incoming
link.
o Route.LastUsed := Current_Time
o If RteMsg.VALIDITY_TIME is included, then
Route.ExpirationTime := Current_Time + RteMsg.VALIDITY_TIME,
otherwise, Route.ExpirationTime := Current_Time + (ACTIVE_INTERVAL
+ MAX_IDLETIME).
With these assignments to the route table entry, a route has been
made available, and the route can be used to send any buffered data
packets and subsequently to forward any incoming data packets for
Route.Address. An updated route entry also fulfills any outstanding
route discovery (RREQ) attempts for Route.Address.
6.3. Route Table Entry Timeouts
During normal operation, AODVv2 does not require any explicit
timeouts to manage the lifetime of a route. However, the route table
entry MUST be examined before using it to forward a packet, as
discussed in Section 8.1. Any required expiry or deletion can occur
at that time. Nevertheless, it is permissible to implement timers
and timeouts to achieve the same effect.
At any time, the route table can be examined and route table entries
can be expunged according to their current state at the time of
examination, as follows.
o An Active route MUST NOT be expunged.
Perkins, et al. Expires August 8, 2014 [Page 19]
Internet-Draft AODVv2 February 2014
o An Idle route SHOULD NOT be expunged.
o An Expired route MAY be expunged (least recently used first).
o A route MUST be expunged if (Current_Time - Route.LastUsed) >=
MAX_SEQNUM_LIFETIME.
o A route MUST be expunged if Current_Time >= Route.ExpirationTime
If precursor lists are maintained for the route (as described in
Section 13.3) then the precursor lists must also be expunged at the
same time that the route itself is expunged.
7. Routing Messages RREQ and RREP (RteMsgs)
AODVv2 message types RREQ and RREP are together known as Routing
Messages (RteMsgs) and are used to discover a route between an
Originating and Target Node, denoted here by OrigNode and TargNode.
The constructed route is bidirectional, enabling packets to flow
between OrigNode and TargNode. RREQ and RREP have similar
information and function, but have some differences in their rules
for handling. The main difference between the two messages is that
RREQ messages are typically multicast to solicit a RREP, whereas RREP
is typically unicast as a response to RREQ.
When an AODVv2 router needs to forward a data packet from a node
(OrigNode) in its set of router clients, and it does not have a
forwarding route toward the packet's IP destination address
(TargNode), the AODVv2 router (RREQ_Gen) generates a RREQ (as
described in Section 7.3) to discover a route toward TargNode.
Subsequently RREQ_Gen awaits reception of an RREP message (see
Section 7.4) or other route table update (see Section 6.2) to
establish a route toward TargNode. Optionally, RREQ_Gen MAY specify
that only the router serving TargNode is allowed to generate an RREP
message, by including the DestOnly message TLV (see Section 7.3).
The RREQ message contains routing information to enable RREQ
recipients to route packets back to OrigNode, and the RREP message
contains routing information enabling RREP recipients to route
packets to TargNode.
7.1. Route Discovery Retries and Buffering
After issuing a RREQ, as described above RREQ_Gen awaits a RREP
providing a bidirectional route toward Target Node. If the RREP is
not received within RREQ_WAIT_TIME, RREQ_Gen may retry the Route
Discovery by generating another RREQ. Route Discovery SHOULD be
considered to have failed after DISCOVERY_ATTEMPTS_MAX and the
corresponding wait time for a RREP response to the final RREQ. After
the attempted Route Discovery has failed, RREQ_Gen MUST wait at least
RREQ_HOLDDOWN_TIME before attempting another Route Discovery to the
same destination.
Perkins, et al. Expires August 8, 2014 [Page 20]
Internet-Draft AODVv2 February 2014
To reduce congestion in a network, repeated attempts at route
discovery for a particular Target Node SHOULD utilize a binary
exponential backoff.
Data packets awaiting a route SHOULD be buffered by RREQ_Gen. This
buffer SHOULD have a fixed limited size (BUFFER_SIZE_PACKETS or
BUFFER_SIZE_BYTES). Determining which packets to discard first is a
matter of policy at each AODVv2 router; in the absence of policy
constraints, by default older data packets SHOULD be discarded first.
Buffering of data packets can have both positive and negative effects
(albeit usually positive). Nodes without sufficient memory available
for buffering SHOULD be configured to disable buffering by
configuring BUFFER_SIZE_PACKETS == 0 and BUFFER_SIZE_BYTES == 0.
Doing so will affect the latency required for launching TCP
applications to new destinations.
If a route discovery attempt has failed (i.e., DISCOVERY_ATTEMPTS_MAX
attempts have been made without receiving a RREP) to find a route
toward the Target Node, any data packets buffered for the
corresponding Target Node MUST BE dropped and a Destination
Unreachable ICMP message (Type 3) SHOULD be delivered to the source
of the data packet. The code for the ICMP message is 1 (Host
unreachable error). If RREQ_Gen is not the source (OrigNode), then
the ICMP is sent over the interface from which OrigNode sent the
packet to the AODVv2 router.
7.2. RteMsg Structure
RteMsgs have the following general format:
+---------------------------------------------------------------+
| RFC 5444 Message Header |
+---------------------------------------------------------------+
| MsgTLVs (e.g., Metric Type TLV {OrigNode,TargNode}(optional)) |
+---------------------------------------------------------------+
| AddrBlk := {OrigNode,TargNode} |
+---------------------------------------------------------------+
| AddrBlk.PrefixLength[OrigNode OR TargNode] (Optional) |
+---------------------------------------------------------------+
| OrigSeqNum_TLV AND/OR TargSeqNum_TLV |
+---------------------------------------------------------------+
| Metric TLV {OrigNode, TargNode} |
+---------------------------------------------------------------+
Figure 1: RREQ and RREP (RteMsg) message structure
Required Message Header Fields
The RteMsg MUST contain the following:
Perkins, et al. Expires August 8, 2014 [Page 21]
Internet-Draft AODVv2 February 2014
* <msg-hop-limit>
* Metric Type Message TLV, if Metric Type != 3
Optional Message Header Fields
The RteMsg may contain the following:
* <msg-hop-count>
* DestOnly TLV (RREQ only: no Intermediate RREP)
* Metric Type TLV (Metric Type for Metric AddrTLV)
* AckReq TLV (Acknowledgement Requested)
AddrBlk
This Address Block contains the IP addresses for RREQ Originating
and Target Node (OrigNode and TargNode). For both RREP and RREQ,
OrigNode and TargNode are as identified in the context of the RREQ
message originator.
OrigSeqNum AND/OR TargSeqNum AddrTLV
At least one of OrigSeqNum or TargSeqNum Address Block TLV is
REQUIRED and carries the destination sequence numbers associated
with either OrigNode or TargNode. Both may appear when SeqNum
information is available for both OrigNode and TargNode.
Metric AddrTLV
The Metric AddrTLV is REQUIRED and carries the route metric
information associated with either OrigNode or TargNode.
RteMsgs carry information about OrigNode and TargNode. Since their
addresses may appear in arbitrary order within the RFC 5444 AddrBlk,
the OrigSeqNum and/or TargSeqNum TLVs must be used to distinguish the
nature of the node addresses present in the AddrBlk. In each RteMsg,
either the OrigSeqNum TLV or TargSeqNum TLV MUST appear. Both TLVs
MAY appear in the same RteMsg, but each one MUST NOT appear more than
once, because there is only one OrigNode and only one TargNode
address in the AddrBlk.
If the OrigSeqNum TLV appears, then the address range for the
OrigSeqNum TLV MUST be limited to a single position in the AddrBlk.
That position is used as the OrigNdx, identifying the OrigNode
address. The other address in the AddrBlk is, by elimination, the
TargNode address, and TargNdx is set appropriately.
Otherwise, if the TargSeqNum TLV appears, then the address range for
the TargSeqNum TLV MUST be limited to a single position in the
AddrBlk. That position is used as the TargNdx, identifying the
TargNode address. The other address in the AddrBlk is, by
elimination, the OrigNode address, and OrigNdx is set appropriately.
Perkins, et al. Expires August 8, 2014 [Page 22]
Internet-Draft AODVv2 February 2014
7.3. RREQ Generation
The AODVv2 router generating the RREQ (RREQ_Gen) on behalf of its
client OrigNode follows the steps in this section. OrigNode MUST be
a unicast address. The order of protocol elements is illustrated
schematically in Figure 1.
1. RREQ_Gen MUST increment its SeqNum by one (1) according to the
rules specified in Section 5.5. This assures that each node
receiving the RREQ will update its route table using the
information in the RREQ.
2. If RREQ_Gen requires that only the router providing connectivity
to TargNode is allowed to generate a RREP, then RREQ_Gen includes
the "Destination RREP Only" (DestOnly) TLV as part of the RFC
5444 message header. This also assures that RREP_Gen increments
its sequence number. Otherwise, (if the optional behavior is
enabled) other AODVv2 routers MAY respond to the RREQ if they
have a valid route to TargNode (see Section 13.2).
3. <msg-hop-limit> SHOULD be set to MAX_HOPCOUNT.
4. <msg-hop-count>, if included, MUST be set to 0.
* This RFC 5444 constraint causes certain RREQ payloads to incur
additional enlargement (otherwise, <msg-hop-count> could often
be used as the metric).
5. RREQ.AddrBlk := {OrigNode.Addr, TargNode.Addr}
Let OrigNdx and TargNdx denote the indexes of OrigNode and
TargNode respectively in the RREQ.AddrBlk list.
6. If Route[OrigNode].PrefixLength/8 is equal to the number of bytes
in the addresses of the RREQ (4 for IPv4, 16 for IPv6), then no
<prefix-length> is included with the RREQ.AddrBlk. Otherwise,
RREQ.PrefixLength[OrigNdx] := Route[OrigNode].PrefixLength
according to the rules of RFC 5444 AddrBlk encoding.
7. RREQ.OrigSeqNum_TLV[OrigNdx] := RREQ_Gen's SeqNum
8. RREQ.TargSeqNum_TLV[TargNdx] := TargNode's SeqNum (only if known)
RREQ_Gen SHOULD include TargNode's SeqNum, if a previous value of
the TargNode's SeqNum is known (e.g., from an invalid routing
table entry using longest-prefix matching). If TargNode's SeqNum
is not included, AODVv2 routers handling the RREQ assume that
RREQ_Gen does not have that information. If ENABLE_IRREP is
enabled, then any route to TargNode will satisfy the RREQ
[I-D.perkins-irrep].
9. RREQ.Metric_TLV[OrigNdx] := Route[OrigNode].Metric
An example RREQ message format is illustrated in Appendix A.1.
Perkins, et al. Expires August 8, 2014 [Page 23]
Internet-Draft AODVv2 February 2014
7.4. RREP Generation
This section specifies the generation of an RREP by an AODVv2 router
(RREP_Gen) that provides connectivity for the Target Node (TargNode)
of a RREQ, thus enabling the establishment of a route between
OrigNode and TargNode. If TargNode is not a unicast IP address the
RREP MUST NOT be generated, and processing for the RREQ is complete.
Before transmitting a RREP, the routing information of the RREQ is
processed as specified in Section 6.2; after such processing,
RREP_Gen has an updated route to OrigNode as well as TargNode. The
basic format of an RREP conforms to the structure for RteMsgs as
shown in Figure 1.
RREP_Gen generates the RREP as follows:
1. RREP_Gen checks the RREQ against recently received RREQ
information as specified in Section 7.6. If a previously
received RREQ has made the information in the incoming RREQ to
be redundant, no RREP is generated and processing is complete.
2. RREP_Gen MUST increment its SeqNum by one (1) according to the
rules specified in Section 5.5.
3. RREP.AddrBlk := {OrigNode.Addr, TargNode.Addr}
Let OrigNdx and TargNdx denote the indexes of OrigNode and
TargNode respectively in the RREQ.AddrBlk list.
4. RREP.TargSeqNum_TLV[TargNdx] := RREP_Gen's SeqNum
5. If Route[TargNode].PrefixLength/8 is equal to the number of
bytes in the addresses of the RREQ (4 for IPv4, 16 for IPv6),
then no <prefix-length> is included with the RREP.AddrBlk.
Otherwise, RREP.PrefixLength[TargNdx] :=
Route[TargNode].PrefixLength according to the rules of RFC 5444
AddrBlk encoding.
6. RREP.MetricType[TargNdx] := Route[TargNode].MetricType
7. RREP.Metric_TLV[TargNdx] := Route[TargNode].Metric
8. <msg-hop-count>, if included, MUST be set to 0.
9. <msg-hop-limit> SHOULD be set to RREQ.<msg-hop-count>.
10. IP.DestinationAddr := Route[OrigNode].NextHop
An example message format for RREP is illustrated in Appendix A.2.
7.5. Handling a Received RteMsg
Before an AODVv2 router can make use of a received RteMsg (i.e., RREQ
or RREP), the router first must verify that the RteMsg is permissible
according to the following steps. OrigNdx and TargNdx are set
according to the rules in Section 7.2. For RREQ, RteMsg.Metric is
Metric_TLV[OrigNdx]. For RREP, RteMsg.Metric is Metric_TLV[TargNdx].
In this section (unless qualified by additional description such as
Perkins, et al. Expires August 8, 2014 [Page 24]
Internet-Draft AODVv2 February 2014
"upstream" or "neighboring") all occurrences of the term "router"
refer to the AODVv2 router handling the received RteMsg.
1. A router MUST handle RteMsgs only from neighbors as specified in
Section 5.4. RteMsgs from other sources MUST be disregarded.
2. The router examines the RteMsg to ascertain that it contains the
required information: <msg-hop-limit>, TargNode.Addr,
OrigNode.Addr, RteMsg.Metric, and either RteMsg.OrigSeqNum or
RteMsg.TargSeqNum. If the required information does not exist,
the message is disregarded.
3. The router checks that OrigNode.Addr and TargNode.Addr are valid
routable unicast addresses. If not, the message is disregarded.
4. The router checks the Metric Type MsgTLV (if present) to assure
that the Metric Type associated with the Metric AddrTLV
information in the RREQ or RREP is known. If not, the message is
disregarded.
* DISCUSSION: or, can change the AddrBlk metric to use HopCount,
e.g., measured from <msg-hop-count>.
5. If (MAX_METRIC[RteMsg.MetricType] - Cost(L)) <= RteMsg.Metric,
the RteMsg is disregarded, where Cost(L) denotes the cost of
traversing the incoming link (i.e., as measured by the network
interface receiving the incoming RteMsg).
An AODVv2 router handles a permissible RteMsg according to the
following steps.
1. The router MUST process the routing information for OrigNode and
TargNode contained in the RteMsg as specified in Section 6.1.
2. If RteMsg.<msg-hop-limit> is zero (0), no further action is
taken, and the RteMsg is not retransmitted. Otherwise, the
router MUST decrement RteMsg.<msg-hop-limit>.
3. If the RteMsg.<msg-hop-count> is present, and MAX_HOPCOUNT <=
<msg-hop-count>, then no further action is taken. Otherwise, the
router MUST increment RteMsg.<msg-hop-count>
Further actions to transmit an updated RteMsg depend upon whether the
incoming RteMsg is an RREP or an RREQ.
7.5.1. Additional Handling for Incoming RREQ
o By sending a RREQ, a router advertises that it will route for
addresses contained in the RteMsg based on the information
enclosed. The router MAY choose not to send the RREQ, though not
resending the RREQ could decrease connectivity in the network or
result in nonoptimal paths. The circumstances under which a
router might choose not to re-transmit a RREQ are not specified in
this document. Some examples might include the following:
Perkins, et al. Expires August 8, 2014 [Page 25]
Internet-Draft AODVv2 February 2014
* The router is already heavily loaded and does not want to
advertise routing for more traffic
* The router recently transmitted identical routing information
(e.g. in a RREQ advertising the same metric) Section 7.6
* The router is low on energy and has to reduce energy expended
for sending protocol messages or packet forwarding
Unless the router is prepared to send a RREQ, it halts processing.
o If the upstream router sending a RREQ is in the Blacklist, and
Current_Time < Blacklist.RemoveTime, then the router receiving
that RREQ MUST NOT transmit any outgoing RteMsg, and processing is
complete.
o Otherwise, if the upstream router is in the Blacklist, and
Current_Time >= Blacklist.RemoveTime, then the upstream router
SHOULD be removed from the Blacklist, and message processing
continued.
o The incoming RREQ MUST be checked against previously received
information from the RREQ Table Section 7.6. If the information
in the incoming RteMsg is redundant, then then no further action
is taken.
o If TargNode is a client of the router receiving the RREQ, then the
router generates a RREP message as specified in Section 7.4, and
subsequently processing for the RREQ is complete. Otherwise,
processing continues as follows.
o RREQ.MetricType := Route[OrigNode].MetricType
o RREQ.Metric_TLV[OrigNdx] := Route[OrigNode].Metric
o The RREQ (with updated fields as specified above>) SHOULD be sent
to the IP multicast address LL-MANET-Routers [RFC5498]. If the
RREQ is unicast, the IP.DestinationAddress is set to
Route[RREQ.TargNode].NextHopAddress.
7.5.2. Additional Handling for Incoming RREP
As before, OrigNode and TargNode are named in the context of RREQ_Gen
(i.e., the router originating the RREQ for which the RREP was
generated) (see Table 1). OrigNdx and TargNdx are set according to
the rules in Section 7.2.
o If no forwarding route exists to OrigNode, then a RERR SHOULD be
transmitted to RREP.AddrBlk[TargNdx]. Otherwise, if HandlingRtr
is not RREQ_Gen then the outgoing RREP is sent to the
Route.NextHopAddress for the RREP.AddrBlk[OrigNdx].
o If HandlingRtr is RREQ_Gen then the RREP satisfies RREQ_Gen's
earlier RREQ, and RREP processing is completed. Any packets
buffered for OrigNode should be transmitted.
Perkins, et al. Expires August 8, 2014 [Page 26]
Internet-Draft AODVv2 February 2014
7.6. Suppressing Redundant RREQ messages
Since RREQ messages are multicast, there are common circumstances in
which an AODVv2 router might transmit a redundant response (RREQ or
RREP), duplicating the information transmitted in response to some
other recent RREQ (see Section 5.7). Before responding, an AODVv2
router MUST suppress such redundant RREQ messages. This is done by
checking the list of recently received RREQs to determine whether the
incoming RREQ contains new information, as follows:
o The AODVv2 router searches the RREQ Table for recent entries with
the same OrigNode, TargNode, and Metric Type. If there is no such
entry, the incoming RREQ message is not suppressed. A new entry
for the incoming RREQ is created in the RREQ Table.
o If there is such an entry, and the incoming RREQ has a newer
sequence number, the incoming RREQ is not suppressed, and the
existing table entry MUST be updated to reflect the new Sequence
Number and Metric.
o Similarly, if the Sequence Numbers are the same, and the incoming
RREQ offers a better Metric, the incoming RREQ is not suppressed,
and the RREQ Table entry MUST be updated to reflect the new
Metric.
o Otherwise, the incoming RREQ is suppressed.
8. Route Maintenance and RERR Messages
AODVv2 routers attempt to maintain active routes. When a routing
problem is encountered, an AODVv2 router (denoted RERR_Gen) attempts
to quickly notify upstream routers. Two kinds of routing problems
may trigger generation of a RERR message. The first case happens
when the router receives a packet but does not have a route for the
destination of the packet. The second case happens immediately upon
detection of a broken link (see Section 8.2) of an Active route, to
quickly notify upstream AODVv2 routers that that route is no longer
available.
8.1. Maintaining Route Lifetimes During Packet Forwarding
Before using a route to forward a packet, an AODVv2 router MUST check
the status of the route as follows.
If the route is marked has been marked as Broken, it cannot be
used for forwarding.
If Current_Time > Route.ExpirationTime, the route table entry has
expired, and cannot be used for forwarding.
Similarly, if (Route.ExpirationTime == MAXTIME), and if
(Current_Time - Route.LastUsed) > (ACTIVE_INTERVAL +
Perkins, et al. Expires August 8, 2014 [Page 27]
Internet-Draft AODVv2 February 2014
MAX_IDLETIME), the route has expired, and cannot be used for
forwarding.
Furthermore, if Current_Time - Route.LastUsed >
(MAX_SEQNUM_LIFETIME), the route table entry MUST be expunged.
If any of the above route error conditions hold true, the route
cannot be used to forward the packet, and an RERR message MUST be
generated (see Section 8.3).
Otherwise, Route.LastUsed := Current_Time, and the packet is
forwarded to the route's next hop.
Optionally, if a precursor list is maintained for the route, see
Section 13.3 for precursor lifetime operations.
8.2. Active Next-hop Router Adjacency Monitoring
AODVv2 routers SHOULD monitor connectivity to adjacent routers along
active routes. This monitoring can be accomplished by one or several
mechanisms, including:
o Neighborhood discovery [RFC6130]
o Route timeout
o Lower layer trigger that a link is broken
o TCP timeouts
o Promiscuous listening
o Other monitoring mechanisms or heuristics
If a next-hop AODVv2 router has become unreachable, RERR_Gen follows
the procedures specified in Section 8.3.2.
8.3. RERR Generation
An RERR message is generated by a AODVv2 router (i.e., RERR_Gen) in
order to notify upstream routers that packets cannot be delivered to
certain destinations. An RERR message has the following general
structure:
+---------------------------------------------------------------+
| RFC 5444 Message Header <msg-hoplimit> <msg-hopcount> |
+---------------------------------------------------------------+
| UnreachableNode AddrBlk (Unreachable Node addresses) |
+---------------------------------------------------------------+
| UnreachableNode SeqNum AddrBlk TLV |
+---------------------------------------------------------------+
Figure 2: RERR message structure
Perkins, et al. Expires August 8, 2014 [Page 28]
Internet-Draft AODVv2 February 2014
Required Message Header Fields
The RERR MUST contain the following:
* <msg-hop-limit>
* PktSource Message TLV (see Section 15), if the RERR is unicast
* Metric Type Message TLV (see Section 15), if Metric Type != 3
Optional Message Header Fields
The RERR SHOULD contain the following:
* <msg-hop-count>
UnreachableNode AddrBlk
This Address Block contains the IP addresses unreachable by AODVv2
router transmitting the RERR.
Sequence Number AddrBlk TLV
This Address Block TLV carries the destination sequence number
associated with each UnreachableNode when that information is
available.
UnreachableNode.PrefixLength
The prefix length associated with an UnreachableNode.
There are two kinds of events indicating that packets cannot be
delivered to certain destinations. The two cases differ in the way
that the neighboring IP destination address for the RERR is chosen,
and in the way that the set of UnreachableNodes is identified.
In both cases, the <msg-hop-limit> MUST be included and SHOULD be set
to MAX_HOPCOUNT. <msg-hop-count> SHOULD be included and set to 0, to
facilitate use of various route repair strategies including expanding
rings multicast and Intermediate RREP [I-D.perkins-irrep].
8.3.1. Case 1: Undeliverable Packet
The first case happens when the router receives a packet from another
AODVv2 router but does not have a valid route for the destination of
the packet. In this case, there is exactly one UnreachableNode to be
included in the RERR's AddrBlk (either IP.DestinationAddress from a
data packet or RREP.AddrBlk[OrigNode]). The RERR SHOULD be sent to
the multicast address LL-MANET-Routers, but RERR_Gen MAY instead send
the RERR to the next hop towards the source IP address of the packet
which was undeliverable. For unicast RERR, the PktSource Message TLV
MUST be included, containing the the source IP address of the
undeliverable packet, or the IP address of TargRtr in case the
undeliverable packet was an RREP message generated by TargRtr. If a
Sequence Number for UnreachableNode is known, that Sequence Number
SHOULD be included in a Seqnum AddrTLV the RERR. Otherwise all nodes
handling the RERR will assume their route through RERR_Gen towards
the UnreachableNode is no longer valid and flag those routes as
broken, regardless of the Sequence Number information for those
Perkins, et al. Expires August 8, 2014 [Page 29]
Internet-Draft AODVv2 February 2014
routes. RERR_Gen MUST discard the packet or message that triggered
generation of the RERR.
If an AODVv2 router receives an ICMP packet from the address of one
of its client nodes, it simply relays the packet to the ICMP packet's
destination address, and does not generate any RERR message.
8.3.2. Case 2: Broken Link
The second case happens when the link breaks to an active adjacent
AODVv2 router (i.e., the next hop of an active route). In this case,
the RERR MUST be sent to the multicast address LL-MANET-Routers,
except when the optional feature of maintaining precursor lists is
used as specified in Section 13.3. All routes (Active, Idle and
Expired) that use the broken link MUST be marked as Broken. The set
of UnreachableNodes is initialized by identifying those Active routes
which use the broken link. For each such Active Route, Route.Dest is
added to the set of Unreachable Nodes. After the Active Routes using
the broken link have all been included as UnreachableNodes, Idle
routes MAY also be included, if allowed by the setting of
ENABLE_IDLE_UNREACHABLE, as long as the packet size of the RERR does
not exceed the MTU (interface "Maximum Transfer Unit") of the
physical medium.
If the set of UnreachableNodes is empty, no RERR is generated.
Otherwise, RERR_Gen generates a new RERR, and the address of each
UnreachableNode is inserted into an AddrBlock. The value for each
UnreachableNode's SeqNum (UnreachableNode.SeqNum) MUST be placed in
the SeqNum AddrTLV. If none of UnreachableNode.Addr entries are
associated with routing prefixes (i.e., no prefix length is shorter
than the maximum length for the address family), then the AddrBlk
SHOULD NOT include any prefix-length information.
Every broken route reported in the RERR MUST have the same Metric
Type. If the Metric Type is not 3, then the RERR message MUST
contain a Metric Type MsgTLV indicating the Metric Type of the broken
route(s).
8.4. Receiving and Handling RERR Messages
When an AODVv2 router (HandlingRtr) receives a RERR message, it uses
the information provided to invalidate affected routes. If the
information in the RERR may be relevant to upstream neighbors using
those routes, HandlingRtr subsequently sends another RERR to those
neighbors. This operation has the effect of retransmitting the RERR
information and is counted as another "hop" for purposes of properly
modifying <msg-hop-limit> and <msg-hop-count> in the RERR message
header.
Perkins, et al. Expires August 8, 2014 [Page 30]
Internet-Draft AODVv2 February 2014
HandlingRtr examines the incoming RERR to assure that it contains
<msg-hop-limit> and at least one UnreachableNode.Address. If the
required information does not exist, the incoming RERR message is
disregarded and further processing stopped. Otherwise, for each
UnreachableNode.Address, HandlingRtr searches its route table for a
route using longest prefix matching. If no such Route is found,
processing is complete for that UnreachableNode.Address. Otherwise,
HandlingRtr verifies the following:
1. The UnreachableNode.Address is a routable unicast address.
2. Route.NextHopAddress is the same as RERR IP.SourceAddress.
3. Route.NextHopInterface is the same as the interface on which the
RERR was received.
4. The UnreachableNode.SeqNum is unknown, OR Route.SeqNum <=
UnreachableNode.SeqNum (using signed 16-bit arithmetic).
If the Route satisfies all of the above conditions, HandlingRtr
checks whether Route.PrefixLength is the same as the prefix length
for UnreachableNode.Address. If so, HandlingRtr simply sets the
Route.Broken flag for that Route. Otherwise, HandlingRtr creates a
new route (call it BrokenRoute) with the same PrefixLength as the
prefix length for UnreachableNode.Address, and sets the
BrokenRoute.Broken flag for that new route. If the prefix length for
BrokenRoute is shorter than Route.PrefixLength, then Route MUST be
expunged from the routing table (since it is a subroute of the larger
route which is reported to be broken). Furthermore, if <msg-hop-
limit> is greater than 0, then HandlingRtr adds the UnreachableNode
address and TLV information to an AddrBlk for delivery in the
outgoing RERR message.
If there are no UnreachableNode addresses to be transmitted in an
RERR to upstream routers, HandlingRtr MUST discard the RERR, and no
further action is taken.
Otherwise, <msg-hop-limit> is decremented by one (1) and processing
continues as follows:
o (Optional) If precursor lists are maintained, the outgoing RERR
SHOULD be sent to the active precursors of the broken route as
specified in Section 13.3.
o Otherwise, if the incoming RERR message was received at the LL-
MANET-Routers [RFC5498] multicast address, the outgoing RERR
SHOULD also be sent to LL-MANET-Routers.
o Otherwise, if the PktSource Message TLV is present, and
HandlingRtr has a Route to PktSource.Addr, then HandlingRtr MUST
send the outgoing RERR to Route[PktSource.Addr].NextHop.
o Otherwise, the outgoing RERR MUST be sent to LL-MANET-Routers.
Perkins, et al. Expires August 8, 2014 [Page 31]
Internet-Draft AODVv2 February 2014
9. Unknown Message and TLV Types
If a message with an unknown type is received, the message is
disregarded.
For handling of messages that contain unknown TLV types, ignore the
information for processing, but preserve it unmodified for
forwarding.
10. Simple Internet Attachment
Simple Internet attachment means attachment of a stub (i.e., non-
transit) network of AODVv2 routers to the Internet via a single
Internet AODVv2 router (called IAR).
As in any Internet-attached network, AODVv2 routers, and their
clients, wishing to be reachable from hosts on the Internet MUST have
IP addresses within the IAR's routable and topologically correct
prefix (e.g. 191.0.2.0/24).
/-------------------------\
/ +----------------+ \
/ | AODVv2 Router | \
| | 191.0.2.2/32 | |
| +----------------+ | Routable
| +-----+--------+ Prefix
| | Internet | /191.0.2/24
| | AODVv2 Router| /
| | 191.0.2.1 |/ /---------------\
| | serving net +------+ Internet \
| | 191.0.2/24 | \ /
| +-----+--------+ \---------------/
| +----------------+ |
| | AODVv2 Router | |
| | 191.0.2.3/32 | |
\ +----------------+ /
\ /
\-------------------------/
Figure 3: Simple Internet Attachment Example
When an AODVv2 router within the AODVv2 MANET wants to discover a
route toward a node on the Internet, it uses the normal AODVv2 route
discovery for that IP Destination Address. The IAR MUST respond to
RREQ on behalf of all Internet destinations.
When a packet from a node on the Internet destined for a node in the
AODVv2 MANET reaches the IAR, if the IAR does not have a route toward
Perkins, et al. Expires August 8, 2014 [Page 32]
Internet-Draft AODVv2 February 2014
that destination it will perform normal AODVv2 route discovery for
that destination.
11. Multiple Interfaces
AODVv2 may be used with multiple interfaces; therefore, the
particular interface over which packets arrive MUST be known whenever
a packet is received. Whenever a new route is created, the interface
through which the Route.Address can be reached is also recorded in
the route table entry.
When multiple interfaces are available, a node transmitting a
multicast packet with IP.DestinationAddress set to LL-MANET-Routers
SHOULD send the packet on all interfaces that have been configured
for AODVv2 operation.
Similarly, AODVv2 routers SHOULD subscribe to LL-MANET-Routers on all
their AODVv2 interfaces.
12. AODVv2 Control Packet/Message Generation Limits
To avoid messaging overload, each AODVv2 router's rate of packet/
message generation SHOULD be limited. The rate and algorithm for
limiting messages (CONTROL_TRAFFIC_LIMITS) is left to the implementor
and should be administratively configurable. AODVv2 messages SHOULD
be discarded in the following order of preference: RREQ, RREP, and
finally RERR.
13. Optional Features
Some optional features of AODVv2, associated with AODV, are not
required by minimal implementations. These features are expected to
apply in networks with greater mobility, or larger node populations,
or requiring reduced latency for application launches. The optional
features are as follows:
o Expanding Rings Multicast
o Intermediate RREPs (iRREPs): Without iRREP, only the destination
can respond to a RREQ.
o Precursor lists.
o Reporting Multiple Unreachable Nodes. An RERR message can carry
more than one Unreachable Destination node for cases when a single
link breakage causes multiple destinations to become unreachable
from an intermediate router.
o RREP_ACK.
o Message Aggregation.
Perkins, et al. Expires August 8, 2014 [Page 33]
Internet-Draft AODVv2 February 2014
13.1. Expanding Rings Multicast
For multicast RREQ, <msg-hop-limit> MAY be set in accordance with an
expanding ring search as described in [RFC3561] to limit the RREQ
propagation to a subset of the local network and possibly reduce
route discovery overhead.
13.2. Intermediate RREP
This specification has been published as a separate Internet Draft
[I-D.perkins-irrep].
13.3. Precursor Lists and Notifications
This section specifies an interoperable enhancement to AODVv2 (and
possibly other reactive routing protocols) enabling more economical
notifications to active sources of traffic upon determination that a
route needed to forward such traffic to its destination has become
Broken.
13.3.1. Overview
In many circumstances, there can be several sources of traffic for a
certain destination. Each such source of traffic is known as a
"precursor" for the destination, as well as all upstream routers
between the forwarding AODVv2 router and the traffic source. For
each active destination, an AODVv2 router MAY choose to keep track of
the upstream neighbors that have provided traffic for that
destination; there is no need to keep track of upstream routers any
farther away than the next hop.
Moreover, any particular link to an adjacent AODVv2 router may be a
path component of multiple routes towards various destinations. The
precursors for all destinations using the next hop across any link
are collectively known as the precursors for that next hop.
When an AODVv2 router determines that an active link to one of its
downstream neighbors has broken, the AODVv2 router detecting the
broken link must mark multiple routes as Broken, for each of the
newly unreachable destinations, as described in Section 8.3. Each
route that relies on the newly broken link is no longer valid.
Furthermore, the precursors of the broken link should be notified
(using RERR) about the change in status of their route to a
destination downstream along the broken next hop.
Perkins, et al. Expires August 8, 2014 [Page 34]
Internet-Draft AODVv2 February 2014
13.3.2. Precursor Notification Details
During normal operation, each AODVv2 router wishing to maintain
precursor lists as described above, maintains a precursor table and
updates the table whenever the node forwards traffic to one of the
destinations in its route table. For each precursor in the precursor
list, a record must be maintained to indicate whether the precursor
has been used for recent traffic (in other words, whether the
precursor is an Active precursor). So, when traffic arrives from a
precursor, the Current_Time is used to mark the time of last use for
the precursor list element associated with that precursor.
When an AODVv2 router detects that a link is broken, then for each
precursor using that next hop, the node MAY notify the precursor
using either unicast or multicast RERR:
unicast RERR to each Active precursor
This option is applicable when there are few Active precursors
compared to the number of neighboring AODVv2 routers.
multicast RERR to RERR_PRECURSORS
RERR_PRECURSORS is, by default, LL-MANET-Routers [RFC5498]. This
option is typically preferable when there are many precursors,
since fewer packet transmissions are required.
Each active upstream neighbor (i.e., precursor) MAY then execute the
same procedure until all active upstream routers have received the
RERR notification.
13.4. Multicast RREP Response to RREQ
The RREQ Target Router (RREP_Gen) MAY, as an alternative to
unicasting a RREP, be configured to distribute routing information
about the route toward the RREQ TargNode (RREP_Gen's client) more
widely. That is, RREP_Gen MAY be configured respond to a route
discovery by generating a RREP, using the procedure in Section 7.4,
but multicasting the RREP to LL-MANET-Routers [RFC5498] (subject to
similar suppression algorithm for redundant RREP multicasts as
described in Section 7.6). The redundant message suppression must
occur at every router handling the multicast RREP. Afterwards,
RREP_Gen processing for the incoming RREQ is complete.
Broadcast RREP response to incoming RREQ was originally specified to
handle unidirectional links, but it is expensive. Due to the
significant overhead, AODVv2 routers MUST NOT use multicast RREP
unless configured to do so by setting the administrative parameter
USE_MULTICAST_RREP.
Perkins, et al. Expires August 8, 2014 [Page 35]
Internet-Draft AODVv2 February 2014
13.5. RREP_ACK
Instead of relying on existing mechanisms for requesting verification
of link bidirectionality during Route Discovery, RREP_Ack is provided
as an optional feature and modeled on the RREP_Ack message type from
AODV [RFC3561].
Since the RREP_ACK is simply echoed back to the node from which the
RREP was received, there is no need for any additional RFC 5444
address information (or TLVs). Considerations of packet TTL are as
specified in Section 5.4. An example message format is illustrated
in section Appendix A.4.
13.6. Message Aggregation
The aggregation of multiple messages into a packet is specified in
RFC 5444 [RFC5444].
Implementations MAY choose to briefly delay transmission of messages
for the purpose of aggregation (into a single packet) or to improve
performance by using jitter [RFC5148].
14. Administratively Configurable Parameters and Timer Values
AODVv2 uses various configurable parameters of various types:
o Timers
o Protocol constants
o Administrative (functional) controls
o Other administrative parameters and lists
The tables in the following sections show the parameters along their
definitions and default values (if any).
Note: several fields have limited size (bits or bytes). These sizes
and their encoding may place specific limitations on the values that
can be set. For example, <msg-hop-count> is a 8-bit field and
therefore MAX_HOPCOUNT cannot be larger than 255.
14.1. Timers
AODVv2 requires certain timing information to be associated with
route table entries. The default values are as follows, subject to
future experience:
Perkins, et al. Expires August 8, 2014 [Page 36]
Internet-Draft AODVv2 February 2014
+------------------------------+---------------+
| Name | Default Value |
+------------------------------+---------------+
| ACTIVE_INTERVAL | 5 second |
| MAX_IDLETIME | 200 seconds |
| MAX_BLACKLIST_TIME | 200 seconds |
| MAX_SEQNUM_LIFETIME | 300 seconds |
| RREQ_WAIT_TIME | 2 seconds |
| UNICAST_MESSAGE_SENT_TIMEOUT | 1 second |
| RREQ_HOLDDOWN_TIME | 10 seconds |
+------------------------------+---------------+
Table 2: Timing Parameter Values
The above timing parameter values have worked well for small and
medium well-connected networks with moderate topology changes.
The timing parameters SHOULD be administratively configurable for the
network where AODVv2 is used. Ideally, for networks with frequent
topology changes the AODVv2 parameters should be adjusted using
either experimentally determined values or dynamic adaptation. For
example, in networks with infrequent topology changes MAX_IDLETIME
may be set to a much larger value.
14.2. Protocol constants
AODVv2 protocol constants typically do not require changes. The
following table lists these constants, along with their values and a
reference to the specification describing their use.
+------------------------+--------------------+---------------------+
| Name | Default Value | Description |
+------------------------+--------------------+---------------------+
| DISCOVERY_ATTEMPTS_MAX | 3 | Section 7.1 |
| MAX_HOPCOUNT | 20 hops | Section 5.6 |
| MAX_METRIC[i] | Specified only for | Section 5.6 |
| | HopCount | |
| MAXTIME | [TBD] | Maximum expressible |
| | | clock time |
+------------------------+--------------------+---------------------+
Table 3: Parameter Values
14.3. Administrative (functional) controls
The following administrative controls may be used to change the
operation of the network, by enabling optional behaviors. These
options are not required for correct routing behavior, although they
Perkins, et al. Expires August 8, 2014 [Page 37]
Internet-Draft AODVv2 February 2014
may potentially reduce AODVv2 protocol messaging in certain
situations. The default behavior is to NOT enable most such options,
options. Packet buffering is enabled by default.
+-------------------------+-------------------------------+
| Name | Description |
+-------------------------+-------------------------------+
| DEFAULT_METRIC_TYPE | 3 {Hop Count (see [RFC6551])} |
| ENABLE_IDLE_UNREACHABLE | Section 8.3.2 |
| ENABLE_IRREP | Section 7.3 |
| USE_MULTICAST_RREP | Section 13.4 |
+-------------------------+-------------------------------+
Table 4: Administratively Configured Controls
14.4. Other administrative parameters and lists
The following table lists contains AODVv2 parameters which should be
administratively configured for each specific network.
+-----------------------+-----------------------+-----------------+
| Name | Default Value | Cross Reference |
+-----------------------+-----------------------+-----------------+
| AODVv2_INTERFACES | | Section 4 |
| BUFFER_SIZE_PACKETS | 2 | Section 7.1 |
| BUFFER_SIZE_BYTES | MAX_PACKET_SIZE [TBD] | Section 7.1 |
| CLIENT_ADDRESSES | AODVv2_INTERFACES | Section 5.3 |
| CONTROL_TRAFFIC_LIMIT | TBD [50 packets/sec?] | Section 12 |
+-----------------------+-----------------------+-----------------+
Table 5: Other Administrative Parameters
15. IANA Considerations
This section specifies several message types, message tlv-types, and
address tlv-types. Also, a new registry of 16-bit alternate metric
types is specified.
15.1. AODVv2 Message Types Specification
Perkins, et al. Expires August 8, 2014 [Page 38]
Internet-Draft AODVv2 February 2014
+----------------------------------------+------------+
| Name | Type (TBD) |
+----------------------------------------+------------+
| Route Request (RREQ) | 10 |
| Route Reply (RREP) | 11 |
| Route Error (RERR) | 12 |
| Route Reply Acknowledgement (RREP_ACK) | 13 |
+----------------------------------------+------------+
Table 6: AODVv2 Message Types
15.2. Message TLV Type Specification
+-----------------------------------+-------+---------+-------------+
| Name | Type | Length | Cross |
| | (TBD) | in | Reference |
| | | octets | |
+-----------------------------------+-------+---------+-------------+
| Acknowledgment Request (AckReq) | 10 | 0 | Section 5.2 |
| Destination RREP Only (DestOnly) | 11 | 0 | Section 7.3 |
| Packet Source (PktSource) | 12 | 4 or 16 | Section 8.3 |
| Metric Type | 13 | 1 | Section 7.2 |
+-----------------------------------+-------+---------+-------------+
Table 7: Message TLV Types
15.3. Address Block TLV Specification
+-----------------------------+--------+--------------+-------------+
| Name | Type | Length | Value |
| | (TBD) | | |
+-----------------------------+--------+--------------+-------------+
| Metric | 10 | depends on | Section 7.2 |
| | | Metric Type | |
| Sequence Number (SeqNum) | 11 | 2 octets | Section 7.2 |
| Originating Node Sequence | 12 | 2 octets | Section 7.2 |
| Number (OrigSeqNum) | | | |
| Target Node Sequence Number | 13 | 2 octets | Section 7.2 |
| (TargSeqNum) | | | |
| VALIDITY_TIME | 1 | 1 octet | [RFC5497] |
+-----------------------------+--------+--------------+-------------+
Table 8: Address Block TLV (AddrTLV) Types
Perkins, et al. Expires August 8, 2014 [Page 39]
Internet-Draft AODVv2 February 2014
15.4. Metric Type Number Allocation
Metric types are identified according to the assignments as specified
in [RFC6551]. The metric type of the Hop Count metric is assigned to
be 3, in order to maintain compatibility with that existing table of
values from RFC 6551. Non-addititve metrics are not supported in
this draft.
+-----------------------+----------+-------------+
| Name | Type | Metric Size |
+-----------------------+----------+-------------+
| Unallocated | 0 -- 2 | TBD |
| Hop Count | 3 - TBD | 1 octet |
| Unallocated | 4 -- 254 | TBD |
| Reserved | 255 | Undefined |
+-----------------------+----------+-------------+
Table 9: Metric Types
16. Security Considerations
The objective of the AODVv2 protocol is for each router to
communicate reachability information about addresses for which it is
responsible. Positive routing information (i.e. a route exists) is
distributed via RteMsgs and negative routing information (i.e. a
route does not exist) via RERRs. AODVv2 routers that handle these
messages store the contained information to properly forward data
packets, and they generally provide this information to other AODVv2
routers.
This section does not mandate any specific security measures.
Instead, this section describes various security considerations and
potential avenues to secure AODVv2 routing.
The most important security mechanisms for AODVv2 routing are
integrity/authentication and confidentiality.
In situations where routing information or router identity are
suspect, integrity and authentication techniques SHOULD be applied to
AODVv2 messages. In these situations, routing information that is
distributed over multiple hops SHOULD also verify the integrity and
identity of information based on originator of the routing
information.
A digital signature could be used to identify the source of AODVv2
messages and information, along with its authenticity. A nonce or
timestamp SHOULD also be used to protect against replay attacks. S/
Perkins, et al. Expires August 8, 2014 [Page 40]
Internet-Draft AODVv2 February 2014
MIME and OpenPGP are two authentication/integrity protocols that
could be adapted for this purpose.
In situations where confidentiality of AODVv2 messages is important,
cryptographic techniques can be applied.
In certain situations, for example sending a RREP or RERR, an AODVv2
router could include proof that it has previously received valid
routing information to reach the destination, at one point of time in
the past. In situations where routers are suspected of transmitting
maliciously erroneous information, the original routing information
along with its security credentials SHOULD be included.
Note that if multicast is used, any confidentiality and integrity
algorithms used MUST permit multiple receivers to handle the message.
Routing protocols, however, are prime targets for impersonation
attacks. In networks where the node membership is not known, it is
difficult to determine the occurrence of impersonation attacks, and
security prevention techniques are difficult at best. However, when
the network membership is known and there is a danger of such
attacks, AODVv2 messages must be protected by the use of
authentication techniques, such as those involving generation of
unforgeable and cryptographically strong message digests or digital
signatures. While AODVv2 does not place restrictions on the
authentication mechanism used for this purpose, IPsec Authentication
Message (AH) is an appropriate choice for cases where the nodes share
an appropriate security association that enables the use of AH.
In particular, routing messages SHOULD be authenticated to avoid
creation of spurious routes to a destination. Otherwise, an attacker
could masquerade as that destination and maliciously deny service to
the destination and/or maliciously inspect and consume traffic
intended for delivery to the destination. RERR messages SHOULD be
authenticated in order to prevent malicious nodes from disrupting
active routes between communicating nodes.
If the mobile nodes in the ad hoc network have pre-established
security associations, the purposes for which the security
associations are created should include that of authorizing the
processing of AODVv2 control packets. Given this understanding, the
mobile nodes should be able to use the same authentication mechanisms
based on their IP addresses as they would have used otherwise.
If the mobile nodes in the ad hoc network have pre-established
security associations, the purposes for which the security
associations Most AODVv2 messages are transmitted to the multicast
address LL-MANET-Routers [RFC5498]. It is therefore required for
Perkins, et al. Expires August 8, 2014 [Page 41]
Internet-Draft AODVv2 February 2014
security that AODVv2 neighbors exchange security information that can
be used to insert an ICV [RFC6621] into the AODVv2 message block
[RFC5444]. This enables hop-by-hop security, which is proper for
these message types that may have mutable fields. For destination-
only RREP discovery procedures, AODVv2 routers that share a security
association SHOULD use the appropriate mechanisms as specified in RFC
6621. The establishment of these security associations is out of
scope for this document.
17. Acknowledgments
AODVv2 is a descendant of the design of previous MANET on-demand
protocols, especially AODV [RFC3561] and DSR [RFC4728]. Changes to
previous MANET on-demand protocols stem from research and
implementation experiences. Thanks to Elizabeth Belding-Royer for
her long time authorship of AODV. Additional thanks to Derek Atkins,
Emmanuel Baccelli, Ramon Caceres, Thomas Clausen, Christopher
Dearlove, Ulrich Herberg, Henner Jakob, Luke Klein-Berndt, Lars
Kristensen, Tronje Krop, Koojana Kuladinithi, Alexandru Petrescu,
Henning Rogge, Fransisco Ros, Pedro Ruiz, Christoph Sommer, Lotte
Steenbrink, Romain Thouvenin, Jiazi Yi, Seung Yi, and Cong Yuan, for
their reviews AODVv2 and DYMO, as well as several specification
suggestions.
18. References
18.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5082] Gill, V., Heasley, J., Meyer, D., Savola, P., and C.
Pignataro, "The Generalized TTL Security Mechanism
(GTSM)", RFC 5082, October 2007.
[RFC5444] Clausen, T., Dearlove, C., Dean, J., and C. Adjih,
"Generalized Mobile Ad Hoc Network (MANET) Packet/Message
Format", RFC 5444, February 2009.
[RFC5497] Clausen, T. and C. Dearlove, "Representing Multi-Value
Time in Mobile Ad Hoc Networks (MANETs)", RFC 5497, March
2009.
[RFC5498] Chakeres, I., "IANA Allocations for Mobile Ad Hoc Network
(MANET) Protocols", RFC 5498, March 2009.
Perkins, et al. Expires August 8, 2014 [Page 42]
Internet-Draft AODVv2 February 2014
[RFC6551] Vasseur, JP., Kim, M., Pister, K., Dejean, N., and D.
Barthel, "Routing Metrics Used for Path Calculation in
Low-Power and Lossy Networks", RFC 6551, March 2012.
18.2. Informative References
[I-D.perkins-irrep]
Perkins, C. and I. Chakeres, "Intermediate RREP for
dynamic MANET On-demand (AODVv2) Routing", draft-perkins-
irrep-02 (work in progress), November 2012.
[Perkins99]
Perkins, C. and E. Belding-Royer, "Ad hoc On-Demand
Distance Vector (AODV) Routing", Proceedings of the 2nd
IEEE Workshop on Mobile Computing Systems and
Applications, New Orleans, LA, pp. 90-100, February 1999.
[RFC2501] Corson, M. and J. Macker, "Mobile Ad hoc Networking
(MANET): Routing Protocol Performance Issues and
Evaluation Considerations", RFC 2501, January 1999.
[RFC3561] Perkins, C., Belding-Royer, E., and S. Das, "Ad hoc On-
Demand Distance Vector (AODV) Routing", RFC 3561, July
2003.
[RFC4728] Johnson, D., Hu, Y., and D. Maltz, "The Dynamic Source
Routing Protocol (DSR) for Mobile Ad Hoc Networks for
IPv4", RFC 4728, February 2007.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC5148] Clausen, T., Dearlove, C., and B. Adamson, "Jitter
Considerations in Mobile Ad Hoc Networks (MANETs)", RFC
5148, February 2008.
[RFC6130] Clausen, T., Dearlove, C., and J. Dean, "Mobile Ad Hoc
Network (MANET) Neighborhood Discovery Protocol (NHDP)",
RFC 6130, April 2011.
[RFC6549] Lindem, A., Roy, A., and S. Mirtorabi, "OSPFv2 Multi-
Instance Extensions", RFC 6549, March 2012.
[RFC6621] Macker, J., "Simplified Multicast Forwarding", RFC 6621,
May 2012.
Perkins, et al. Expires August 8, 2014 [Page 43]
Internet-Draft AODVv2 February 2014
Appendix A. Example RFC 5444-compliant packet formats
The following subsections show example RFC 5444-compliant packets for
AODVv2 message types RREQ, RREP, RERR, and RREP-Ack. These proposed
message formats are designed based on expected savings from IPv6
addressable MANET nodes, and a layout for the Address TLVs that may
be viewed as natural, even if perhaps not the absolute most compact
possible encoding.
For RteMsgs, the msg-hdr fields are followed by at least one and
optionally two Address Blocks. The first AddrBlk contains OrigNode
and TargNode. For each AddrBlk, there must be AddrTLVs of type
Metric and one of the SeqNum types (i.e, OrigSeqNum, TargSeqNum, or
Seqnum).
There is no Metric Type Message TLV present, so the Metric AddrTLV
measures HopCount. The Metric AddrTLV also provides a way for the
AODV router generating the RREQ or RREP to supply an initial nonzero
cost for the route to its client node (OrigNode or TargNode, for RREQ
or RREP respectively).
In all cases, the length of an address (32 bits for IPv4 and 128 bits
for IPv6) inside an AODVv2 message is indicated by the msg-addr-
length (MAL) in the msg-header, as specified in [RFC5444].
The RFC 5444 header preceding AODVv2 messages in this document has
the format illustrated in Figure 4.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+
| PV=0 | PF=0 |
+-+-+-+-+-+-+-+-+
Figure 4: RFC 5444 Packet Header
The fields in Figure 4 are to be interpreted as follows:
o PV=0 (Packet Header Version = 0)
o PF=0 (Packet Flags = 0)
A.1. RREQ Message Format
Figure 5 illustrates an example RREQ message format.
Perkins, et al. Expires August 8, 2014 [Page 44]
Internet-Draft AODVv2 February 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type=RREQ | MF=4 | MAL=3 | msg-size=28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-hop-limit | msg.tlvs-length=0 | num-addr=2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0|0|0|0| Rsv | head-length=3 | Head (bytes for Orig & Target):
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:Head(Orig&Targ)| Orig.Tail | Target.Tail |addr.TLV.len=11:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:addr.TLV.len=11|type=OrigSeqNum|0|1|0|1|0|0|Rsv| Index-start=0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| tlv-length=2 | Orig.Node Sequence # | type=Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|1|0|1|0|0|Rsv| Index-start=0 | tlv-length=1 | OrigNodeHopCt |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Example IPv4 RREQ, with OrigSeqNum and Metric AddrTLVs
The fields in Figure 5 are to be interpreted as follows:
o msg-type=RREQ (first [and only] message is of type RREQ)
o MF=4 (Message Flags = 4 [only msg-hop-limit field is present])
o MAL=3 (Message Address Length indicator [3 for IPv4, 15 for IPv6])
o msg-size=28 (octets -- counting MsgHdr, MsgTLVs, and AddrBlks)
o msg-hop-limit (initially MAX_HOPCOUNT by default)
o msg.tlvs-length=0 (no Message TLVs)
o num-addr=2 (OrigNode and TargNode addresses in RteMsg AddrBlock)
o AddrBlk flags:
* bit 0 (ahashead): 1
* bit 1 (ahasfulltail): 0
* bit 2 (ahaszerotail): 0
* bit 3 (ahassingleprelen): 0
* bit 4 (ahasmultiprelen): 0
* bits 5-7: RESERVED
o head-length=3 (length of head part of each address is 3 octets)
o Head (3 initial bytes for both Originating & Target addresses)
o Orig.Tail (4th byte of Originating Node IP address)
o Target.Tail (4th byte of Target Node IP address)
o addr.TLV.len = 11 (length in bytes for OrigSeqNum and Metric TLVs
o type=OrigSeqNum (type of first AddrBlk TLV, value 2 octets)
o AddrTLV flags for the OrigSeqNum TLV:
* bit 0 (thastypeext): 0
* bit 1 (thassingleindex): 1
* bit 2 (thasmultiindex): 0
Perkins, et al. Expires August 8, 2014 [Page 45]
Internet-Draft AODVv2 February 2014
* bit 3 (thasvalue): 1
* bit 4 (thasextlen): 0
* bit 5 (tismultivalue): 0
* bits 6-7: RESERVED
o Index-start=0 (OrigSeqNum TLV value applies at index 0)
o tlv-length=2 (so there is only one TLV value, [1 = 2/2])
o Orig.Node Sequence # (TLV value for the OrigSeqNum TLV
o type=Metric (AddrTLV type of second AddrBlk TLV, values 1 octet)
o AddrTLV flags for Metric_TLV:
* bit 0 (thastypeext): 0
* bit 1 (thassingleindex): 1
* bit 2 (thasmultiindex): 0
* bit 3 (thasvalue): 1
* bit 4 (thasextlen): 0
* bit 5 (tismultivalue): 0
* bits 6-7: RESERVED
o Index-start=0 (Metric TLV values start at index 0)
o tlv-length=1 (so there is only one TLV value, [1 = 1/1])
o OrigNodeHopCt (first [and only] TLV value for the Metric TLV)
A.2. RREP Message Format
Figure 6 illustrates a packet format for an example RREP message.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type=RREP | MF=4 | MAL=3 | msg-size=28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-hop-limit | msg.tlvs-length=0 | num-addr=2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0|0|0|0| Rsv | head-length=3 | Head (bytes for Orig & Target):
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:Head(Orig&Targ)| Orig.Tail | Target.Tail |addr.TLV.len=11:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:addr.TLV.len=11|type=TargSeqNum|0|1|0|1|0|0|Rsv| Index-start=1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| tlv-length=2 | Targ.Node Sequence # | type=Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|1|0|1|0|0|Rsv| Index-start=1 | tlv-length=1 | TargNodeHopCt |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Example IPv4 RREP, with TargSeqNum TLV and 1 Metric
Perkins, et al. Expires August 8, 2014 [Page 46]
Internet-Draft AODVv2 February 2014
The fields in Figure 6 are to be interpreted as follows:
o msg-type=RREP (first [and only] message is of type RREP)
o MF=4 (Message Flags = 4 [only msg-hop-limit field is present])
o MAL=3 (Message Address Length indicator [3 for IPv4, 15 for IPv6])
o msg-size=28 (octets -- counting MsgHdr, MsgTLVs, and AddrBlks)
o msg-hop-limit (initially MAX_HOPCOUNT by default)
o msg.tlvs-length=0 (no Message TLVs)
o num-addr=2 (OrigNode and TargNode addresses in RteMsg AddrBlock)
o AddrBlk flags:
* bit 0 (ahashead): 1
* bit 1 (ahasfulltail): 0
* bit 2 (ahaszerotail): 0
* bit 3 (ahassingleprelen): 0
* bit 4 (ahasmultiprelen): 0
* bits 5-7: RESERVED
o head-length=3 (length of head part of each address is 3 octets)
o Head (3 initial bytes for both Originating & Target addresses)
o Orig.Tail (4th byte of Originating Node IP address)
o Target.Tail (4th byte of Target Node IP address)
o addr.TLV.len = 11 (length in bytes for TargSeqNum TLV and Metric
TLV
o type=TargSeqNum (type of first AddrBlk TLV, value 2 octets)
o AddrTLV flags for the TargSeqNum TLV:
* bit 0 (thastypeext): 0
* bit 1 (thassingleindex): 1
* bit 2 (thasmultiindex): 0
* bit 3 (thasvalue): 1
* bit 4 (thasextlen): 0
* bit 5 (tismultivalue): 0
* bits 6-7: RESERVED
o Index-start=1 (TargSeqNum TLV value applies to address at index 1)
o tlv-length=2 (there is one TLV value, 2 bytes in length)
o Targ.Node Sequence # (value for the TargSeqNum TLV)
o type=Metric (AddrTLV type of second AddrBlk TLV, value 1 octet)
o AddrTLV flags for the Metric TLV [01010000, same as for TargSeqNum
TLV]
o Index-start=1 (Metric TLV values start at index 1)
o tlv-length=1 (there is one TLV value, 1 byte in length)
o TargNodeHopCt (first [and only] TLV value for Metric TLV)
Perkins, et al. Expires August 8, 2014 [Page 47]
Internet-Draft AODVv2 February 2014
A.3. RERR Message Format
Figure 7 illustrates an example RERR message format.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type=RERR | MF=4 | MAL=3 | msg-size=24 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-hop-limit | msg.tlvs-length=0 | num-addr=2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0|0|0|0| Rsv | head-length=3 | Head (for both destinations) :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:Head (3rd byte)| Tail(Dest_1) | Tail(Dest_2) | addr.TLV.len=7:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
:addr.TLV.len=7 | type=SeqNum |0|0|1|1|0|1|Rsv| tlv-length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Dest_1 Sequence # | Dest_2 Sequence # |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: Example IPv4 RERR with Two Unreachable Nodes
The fields in Figure 7 are to be interpreted as follows:
o msg-type=RERR (first [and only] message is of type RERR)
o MF=4 (Message Flags = 4 [only msg-hop-limit field is present])
o MAL=3 (Message Address Length indicator [3 for IPv4, 15 for IPv6])
o msg-size=24 (octets -- counting MsgHdr, MsgTLVs, and AddrBlks)
o msg-hop-limit (initially MAX_HOPCOUNT by default)
o msg.tlvs-length=0 (no Message TLVs)
o num-addr=2 (OrigNode and TargNode addresses in RteMsg AddrBlock)
o AddrBlk flags == 10000000 [same as RREQ and RREP AddrBlk examples]
o head-length=3 (length of head part of each address is 3 octets)
o Head (3 initial bytes for both Unreachable Nodes, Dest_1 and
Dest_2)
o Dest_1.Tail (4th byte of Dest_1 IP address)
o Dest_2.Tail (4th byte of Dest_2 IP address)
o addr.TLV.len = 7 (length in bytes for SeqNum TLV
o type=SeqNum (AddrTLV type of AddrBlk TLV, values 2 octets each)
o AddrTLV flags for SeqNum TLV:
* bit 0 (thastypeext): 0
* bit 1 (thassingleindex): 0
* bit 2 (thasmultiindex): 1
* bit 3 (thasvalue): 1
* bit 4 (thasextlen): 0
* bit 5 (tismultivalue): 1
* bits 6-7: RESERVED
Perkins, et al. Expires August 8, 2014 [Page 48]
Internet-Draft AODVv2 February 2014
o tlv-length=4 (so there are two TLV values, [2 = 4/2])
o Dest_1 Sequence # (first of two TLV values for the SeqNum TLV)
o Dest_2 Sequence # (second of two TLV values for the SeqNum TLV)
A.4. RREP_ACK Message Format
The figure below illustrates a packet format for an example RREP_ACK
message.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|msgtype=RREPAck| MF=0 | MAL=3 | msg-size=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8: Example IPv4 RREP_ACK
Appendix B. Changes since revision ...-02.txt
This section lists the changes since AODVv2 revision ...-02.txt
o The "Added Node" feature was removed. This feature was intended
to enable additional routing information to be carried within a
RREQ or a RREP message, thus increasing the amount of topological
information available to nodes along a routing path. However,
enlarging the packet size to include information which might never
be used can increase congestion of the wireless medium. The
feature can be included as an optional feature at a later date
when better algorithms are understood for determining when the
inclusion of additional routing information might be worthwhile.
o Numerous editorial improvements and improvements to consistent
terminology were made. Instances of OrigNodeNdx and TargNodeNdx
were replaced by OrigNdx and TargNdx, to be consistent with the
terminology shown in Table 1.
o Example RREQ and RREP message formats shown in the Appendices were
changed to use OrigSeqNum and TargSeqNum message TLVs instead of
using the SeqNum message TLV.
o Inclusion of the OrigNode's SeqNum in the RREP message is not
specified. The processing rules for the OrigNode's SeqNum were
incompletely specified in previous versions of the draft, and very
Perkins, et al. Expires August 8, 2014 [Page 49]
Internet-Draft AODVv2 February 2014
little benefit is foreseen for including that information, since
reverse path forwarding is used for the RREP.
o Additional acknowledgements were included, and contributors names
were alphabetized.
o Definitions in the Terminology section capitalize the term to be
defined.
o Uncited bibliographic entries deleted.
o Ancient "Changes" sections were deleted.
Appendix C. Shifting Network Prefix Advertisement Between AODVv2
Routers
Only one AODVv2 router within a MANET SHOULD be responsible for a
particular address at any time. If two AODVv2 routers dynamically
shift the advertisement of a network prefix, correct AODVv2 routing
behavior must be observed. The AODVv2 router adding the new network
prefix must wait for any existing routing information about this
network prefix to be purged from the network. Therefore, it must
wait at least ROUTER_SEQNUM_AGE_MAX_TIMEOUT after the previous AODVv2
router for this address stopped advertising routing information on
its behalf.
Authors' Addresses
Charles E. Perkins
Futurewei Inc.
2330 Central Expressway
Santa Clara, CA 95050
USA
Phone: +1-408-330-5305
Email: charliep@computer.org
Stan Ratliff
Cisco
170 West Tasman Drive
San Jose, CA 95134
USA
Email: sratliff@cisco.com
Perkins, et al. Expires August 8, 2014 [Page 50]
Internet-Draft AODVv2 February 2014
John Dowdell
Cassidian
Celtic Springs
Newport, Wales NP10 8FZ
United Kingdom
Email: John.Dowdell@Cassidian.com
Perkins, et al. Expires August 8, 2014 [Page 51]