Mobile Ad hoc Networking (MANET) T. Clausen
Internet-Draft LIX, Ecole Polytechnique
Intended status: Standards Track C. Dearlove
Expires: January 27, 2012 BAE Systems ATC
P. Jacquet
Project Hipercom, INRIA
July 26, 2011
The Optimized Link State Routing Protocol version 2
draft-ietf-manet-olsrv2-12
Abstract
This document describes version 2 of the Optimized Link State Routing
(OLSRv2) protocol for Mobile Ad hoc NETworks (MANETs).
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 27, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Clausen, et al. Expires January 27, 2012 [Page 1]
Internet-Draft OLSRv2 July 2011
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Applicability Statement . . . . . . . . . . . . . . . . . . . 8
4. Protocol Overview and Functioning . . . . . . . . . . . . . . 9
4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2. Routers and Interfaces . . . . . . . . . . . . . . . . . . 12
4.3. Information Base Overview . . . . . . . . . . . . . . . . 13
4.3.1. Local Information Base . . . . . . . . . . . . . . . . 13
4.3.2. Interface Information Bases . . . . . . . . . . . . . 13
4.3.3. Neighbor Information Base . . . . . . . . . . . . . . 14
4.3.4. Topology Information Base . . . . . . . . . . . . . . 14
4.3.5. Received Message Information Base . . . . . . . . . . 15
4.4. Signaling Overview . . . . . . . . . . . . . . . . . . . . 15
4.5. Link Metrics . . . . . . . . . . . . . . . . . . . . . . . 17
4.6. Routing Set . . . . . . . . . . . . . . . . . . . . . . . 18
5. Protocol Parameters and Constants . . . . . . . . . . . . . . 18
5.1. Protocol and Port Numbers . . . . . . . . . . . . . . . . 18
5.2. Multicast Address . . . . . . . . . . . . . . . . . . . . 19
5.3. Interface Parameters . . . . . . . . . . . . . . . . . . . 19
5.3.1. Received Message Validity Time . . . . . . . . . . . . 19
5.4. Router Parameters . . . . . . . . . . . . . . . . . . . . 19
5.4.1. Local History Times . . . . . . . . . . . . . . . . . 19
5.4.2. Link_Metric_Parameters . . . . . . . . . . . . . . . . 19
5.4.3. Message Intervals . . . . . . . . . . . . . . . . . . 20
5.4.4. Advertised Information Validity Times . . . . . . . . 20
5.4.5. Processing and Forwarding Validity Times . . . . . . . 21
5.4.6. Jitter . . . . . . . . . . . . . . . . . . . . . . . . 22
5.4.7. Hop Limit . . . . . . . . . . . . . . . . . . . . . . 22
5.4.8. Willingness . . . . . . . . . . . . . . . . . . . . . 23
5.5. Parameter Change Constraints . . . . . . . . . . . . . . . 24
5.6. Constants . . . . . . . . . . . . . . . . . . . . . . . . 25
5.6.1. Link Metric Constants . . . . . . . . . . . . . . . . 25
6. Link Metric Values . . . . . . . . . . . . . . . . . . . . . . 26
6.1. Link Metric Representation . . . . . . . . . . . . . . . . 26
Clausen, et al. Expires January 27, 2012 [Page 2]
Internet-Draft OLSRv2 July 2011
6.2. Link Metric Compressed Form . . . . . . . . . . . . . . . 26
7. Local Information Base . . . . . . . . . . . . . . . . . . . . 27
7.1. Originator Set . . . . . . . . . . . . . . . . . . . . . . 27
7.2. Local Attached Network Set . . . . . . . . . . . . . . . . 28
8. Interface Information Base . . . . . . . . . . . . . . . . . . 29
9. Neighbor Information Base . . . . . . . . . . . . . . . . . . 30
10. Topology Information Base . . . . . . . . . . . . . . . . . . 31
10.1. Advertising Remote Router Set . . . . . . . . . . . . . . 31
10.2. Router Topology Set . . . . . . . . . . . . . . . . . . . 32
10.3. Routable Address Topology Set . . . . . . . . . . . . . . 32
10.4. Attached Network Set . . . . . . . . . . . . . . . . . . . 33
10.5. Routing Set . . . . . . . . . . . . . . . . . . . . . . . 34
11. Received Message Information Base . . . . . . . . . . . . . . 35
11.1. Received Set . . . . . . . . . . . . . . . . . . . . . . . 35
11.2. Processed Set . . . . . . . . . . . . . . . . . . . . . . 35
11.3. Forwarded Set . . . . . . . . . . . . . . . . . . . . . . 36
12. Information Base Properties . . . . . . . . . . . . . . . . . 36
13. Packets and Messages . . . . . . . . . . . . . . . . . . . . . 38
13.1. Messages . . . . . . . . . . . . . . . . . . . . . . . . . 38
13.2. Packets . . . . . . . . . . . . . . . . . . . . . . . . . 38
13.3. TLVs . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.3.1. Message TLVs . . . . . . . . . . . . . . . . . . . . . 39
13.3.2. Address Block TLVs . . . . . . . . . . . . . . . . . . 39
14. Message Processing and Forwarding . . . . . . . . . . . . . . 41
14.1. Actions when Receiving a Message . . . . . . . . . . . . . 42
14.2. Message Considered for Processing . . . . . . . . . . . . 43
14.3. Message Considered for Forwarding . . . . . . . . . . . . 44
15. HELLO Messages . . . . . . . . . . . . . . . . . . . . . . . . 45
15.1. HELLO Message Generation . . . . . . . . . . . . . . . . . 46
15.2. HELLO Message Transmission . . . . . . . . . . . . . . . . 47
15.3. HELLO Message Processing . . . . . . . . . . . . . . . . . 48
15.3.1. HELLO Message Discarding . . . . . . . . . . . . . . . 48
15.3.2. HELLO Message Usage . . . . . . . . . . . . . . . . . 49
16. TC Messages . . . . . . . . . . . . . . . . . . . . . . . . . 52
16.1. TC Message Generation . . . . . . . . . . . . . . . . . . 52
16.2. TC Message Transmission . . . . . . . . . . . . . . . . . 54
16.3. TC Message Processing . . . . . . . . . . . . . . . . . . 55
16.3.1. Invalid Message . . . . . . . . . . . . . . . . . . . 55
16.3.2. TC Message Processing Definitions . . . . . . . . . . 56
16.3.3. Initial TC Message Processing . . . . . . . . . . . . 57
16.3.4. Completing TC Message Processing . . . . . . . . . . . 60
17. Information Base Changes . . . . . . . . . . . . . . . . . . . 61
17.1. Originator Address Changes . . . . . . . . . . . . . . . . 61
17.2. Link State Changes . . . . . . . . . . . . . . . . . . . . 62
17.3. Neighbor State Changes . . . . . . . . . . . . . . . . . . 62
17.4. Advertised Neighbor Changes . . . . . . . . . . . . . . . 63
17.5. Advertising Remote Router Tuple Expires . . . . . . . . . 63
17.6. Neighborhood Changes and MPR Updates . . . . . . . . . . . 64
Clausen, et al. Expires January 27, 2012 [Page 3]
Internet-Draft OLSRv2 July 2011
17.7. Routing Set Updates . . . . . . . . . . . . . . . . . . . 65
18. Selecting MPRs . . . . . . . . . . . . . . . . . . . . . . . . 66
19. Routing Set Calculation . . . . . . . . . . . . . . . . . . . 68
19.1. Network Topology Graph . . . . . . . . . . . . . . . . . . 68
19.2. Populating the Routing Set . . . . . . . . . . . . . . . . 70
20. Proposed Values for Parameters and Constants . . . . . . . . . 71
20.1. Local History Time Parameters . . . . . . . . . . . . . . 72
20.2. Message Interval Parameters . . . . . . . . . . . . . . . 72
20.3. Advertised Information Validity Time Parameters . . . . . 72
20.4. Received Message Validity Time Parameters . . . . . . . . 72
20.5. Jitter Time Parameters . . . . . . . . . . . . . . . . . . 72
20.6. Hop Limit Parameter . . . . . . . . . . . . . . . . . . . 72
20.7. Willingness Parameter and Constants . . . . . . . . . . . 72
21. Sequence Numbers . . . . . . . . . . . . . . . . . . . . . . . 73
22. Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . 73
23. Security Considerations . . . . . . . . . . . . . . . . . . . 74
23.1. Confidentiality . . . . . . . . . . . . . . . . . . . . . 74
23.2. Integrity . . . . . . . . . . . . . . . . . . . . . . . . 74
23.3. Interaction with External Routing Domains . . . . . . . . 76
24. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 76
24.1. Expert Review: Evaluation Guidelines . . . . . . . . . . . 76
24.2. Message Types . . . . . . . . . . . . . . . . . . . . . . 77
24.3. Message-Type-specific TLV Type Registries . . . . . . . . 77
24.4. Message TLV Types . . . . . . . . . . . . . . . . . . . . 77
24.5. Address Block TLV Types . . . . . . . . . . . . . . . . . 79
24.6. NBR_ADDR_TYPE Values . . . . . . . . . . . . . . . . . . . 81
25. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 82
26. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 82
27. References . . . . . . . . . . . . . . . . . . . . . . . . . . 82
27.1. Normative References . . . . . . . . . . . . . . . . . . . 82
27.2. Informative References . . . . . . . . . . . . . . . . . . 83
Appendix A. Example Algorithm for Calculating MPRs . . . . . . . 84
A.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 85
A.2. MPR Selection Algorithm for each OLSRv2 Interface . . . . 85
Appendix B. Example Algorithm for Calculating the Routing Set . . 86
B.1. Local Interfaces and Neighbors . . . . . . . . . . . . . . 86
B.2. Add Neighbor Routers . . . . . . . . . . . . . . . . . . . 87
B.3. Add Remote Routers . . . . . . . . . . . . . . . . . . . . 87
B.4. Add Neighbor Addresses . . . . . . . . . . . . . . . . . . 88
B.5. Add Remote Routable Addresses . . . . . . . . . . . . . . 89
B.6. Add Attached Networks . . . . . . . . . . . . . . . . . . 89
B.7. Add 2-Hop Neighbors . . . . . . . . . . . . . . . . . . . 90
Appendix C. TC Message Example . . . . . . . . . . . . . . . . . 91
Appendix D. Constraints . . . . . . . . . . . . . . . . . . . . . 93
Appendix E. Flow and Congestion Control . . . . . . . . . . . . . 98
Clausen, et al. Expires January 27, 2012 [Page 4]
Internet-Draft OLSRv2 July 2011
1. Introduction
The Optimized Link State Routing protocol version 2 (OLSRv2) is an
update to OLSR (version 1) as published in [RFC3626]. Compared to
[RFC3626], OLSRv2 retains the same basic mechanisms and algorithms,
enhanced by the ability to use a link metric other than hop count in
the selection of shortest routes. OLSRv2 also uses a more flexible
and efficient signaling framework, and includes some simplification
of the messages being exchanged.
OLSRv2 is developed for mobile ad hoc networks. It operates as a
table driven, proactive protocol, i.e., it exchanges topology
information with other routers in the network regularly. OLSRv2 is
an optimization of the classical link state routing protocol. Its
key concept is that of MultiPoint Relays (MPRs). Each router selects
as MPRs a set of its neighbor routers that "cover" all of its
symmetrically connected 2-hop neighbor routers. Separate sets of
flooding MPRs and routing MPRs are then used to achieve flooding
reduction and topology reduction, respectively.
Flooding reduction is achieved by control traffic being flooded
through the network using hop by hop forwarding, but with a router
only needing to forward control traffic that is first received
directly from one of the routers that have selected it as a flooding
MPR (its "flooding MPR selectors"). This mechanism, denoted "MPR
flooding", provides an efficient mechanism for information
distribution within the MANET by reducing the number of transmissions
required.
Topology reduction is achieved by assigning a special responsibility
to routers selected as routing MPRs when declaring link state
information. A sufficient requirement for OLSRv2 to provide shortest
routes to all destinations is that routers declare link state
information for their routing MPR selectors, if any. Routers that
are not selected as routing MPRs need not send any link state
information. Based on this reduced link state information, routing
MPRs are used as intermediate routers in multi-hop routes.
Thus the use of MPRs allows reduction of the number and the size of
link state messages, and in the amount of link state information
maintained in each router. When possible (in particular when using a
hop count metric) the same routers may be picked as both flooding
MPRs and routing MPRs.
A router selects both routing and flooding MPRs from among its one
hop neighbors connected by "symmetric", i.e., bidirectional, links.
Therefore, selecting routes through routing MPRs avoids the problems
associated with data packet transfer over unidirectional links (e.g.,
Clausen, et al. Expires January 27, 2012 [Page 5]
Internet-Draft OLSRv2 July 2011
the problem of not getting link layer acknowledgments at each hop,
for link layers employing this technique).
OLSRv2 uses and extends [RFC6130] and uses [RFC5444], [RFC5497] and,
optionally, [RFC5148]. These other protocols and specifications were
all originally created as part of OLSRv2, but have been specified
separately for wider use.
OLSRv2 makes no assumptions about the underlying link layer. OLSRv2,
through its use of [RFC6130], may use link layer information and
notifications when available and applicable. Link metrics may be
derived from link layer or any other information. OLSRv2 does not
specify the physical meaning of link metrics, but specifies a means
by which new types of link metrics may be specified in the future,
but used by OLSRv2 without modification.
OLSRv2, as OLSR [RFC3626], inherits its concept of forwarding and
relaying from HIPERLAN (a MAC layer protocol) which is standardized
by ETSI [HIPERLAN], [HIPERLAN2].
Note: This is the first version of this specification to incorporate
the use of link metrics. It is not compete: Section 18 and
Appendix A have not yet been updated to use link metrics and separate
sets of flooding and routing MPRs.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
All terms introduced in [RFC5444], including "packet", "Packet
Header", "message", "Message Header", "Message Body", "Message Type",
"message sequence number", "hop limit", "hop count", "Address Block",
"TLV Block", "TLV", "Message TLV", "Address Block TLV", "type" (of
TLV), "type extension" (of TLV), "value" (of TLV), "address",
"address prefix", and "address object" are to be interpreted as
described there.
All terms introduced in [RFC6130], including "interface", "MANET
interface", "network address", "link", "symmetric link", "1-hop
neighbor", "symmetric 1-hop neighbor", "symmetric 2-hop neighbor",
"constant", "interface parameter", "router parameter", "Information
Base", and "HELLO message" are to be interpreted as described there.
Additionally, this specification uses the following terminology:
Clausen, et al. Expires January 27, 2012 [Page 6]
Internet-Draft OLSRv2 July 2011
Router - A MANET router which implements this protocol.
OLSRv2 interface - A MANET interface running this protocol.
Routable address - A network address which may be used as the
destination of a data packet. A router MUST be able to
distinguish a routable address from a non-routable address by
direct inspection of the network address, based on global scope
address allocations by IANA and/or administrative configuration.
Broadcast, multicast and anycast addresses, and addresses which
are limited in scope to less than the entire MANET, MUST NOT be
considered as routable addresses.
Originator address - An address which is unique (within the MANET)
to a router. A router MUST select an originator address; it MAY
choose one of its interface addresses as its originator address.
If it selects a routable address then this MUST be one which this
router will accept as destination. An originator address MUST NOT
have a prefix length, except for when included in an Address Block
where it MAY be associated with a prefix of maximum prefix length
(e.g., if the originator address is an IPv6 address, it MUST have
either no prefix length, or have a prefix length of 128). An
originator address may be a routable or non-routable address.
Message originator address - The originator address of the router
which created a message, as deduced from that message by its
recipient. The message originator address will usually be
included in the message as its <msg-orig-addr> element as defined
in [RFC5444]. However an exceptional case in a HELLO message is
also allowed by this specification, when a router only uses a
single address. For all messages used in this specification,
including HELLO messages defined in [RFC6130], the recipient MUST
be able to deduce an originator address.
Willingness - A numerical value between WILL_NEVER and WILL_ALWAYS
(both inclusive), that represents the router's willingness to be
selected as an MPR.
Willing symmetric 1-hop neighbor - A symmetric 1-hop neighbor of
this router that has willingness not equal to WILL_NEVER.
Symmetric 1-hop neighbor through OLSRv2 interface I - A symmetric
1-hop neighbor of the router via a symmetric link using OLSRv2
interface I of the router.
Clausen, et al. Expires January 27, 2012 [Page 7]
Internet-Draft OLSRv2 July 2011
Willing symmetric 1-hop neighbor through OLSRv2 interface I - A
willing symmetric 1-hop neighbor of the router via a symmetric
link using OLSRv2 interface I of the router.
Symmetric strict 2-hop neighbor - A symmetric 1-hop neighbor of a
willing symmetric 1-hop neighbor that is not a symmetric 1-hop
neighbor.
Symmetric strict 2-hop neighbor through OLSRv2 interface I - A
symmetric 1-hop neighbor of a willing symmetric 1-hop neighbor
through OLSRv2 interface I that is not a symmetric 1-hop neighbor
through OLSRv2 interface I. The router MAY elect to use only
information received over OLSRv2 interface I in making this
determination.
Multipoint relay (MPR) - A router, X, is an MPR for a router, Y, if
router Y has indicated its selection of router X as an MPR in a
recent HELLO message. Router X may be a Flooding MPR for Y, if it
is indicated to participate in the flooding process of messages
received from router Y, or it may be a Routing MPR for Y, if it is
indicated to declare link-state information for the link from X to
Y. It may also be both at the same time.
MPR selector - A router, Y, is an MPR selector of router X if router
Y has selected router X as an MPR.
MPR flooding - The optimized MANET-wide information distribution
mechanism, employed by this protocol, in which a message is
relayed by only a reduced subset of the routers in the network.
MPR flooding is the mechanism by which flooding reduction is
achieved.
This document employs the same notational conventions as in [RFC5444]
and [RFC6130].
3. Applicability Statement
This protocol:
o Is a proactive routing protocol for mobile ad hoc networks
(MANETs) [RFC2501].
o Is designed to work in networks with a dynamic topology, and in
which messages may be lost, such as due to collisions in wireless
networks.
o Supports routers that each have one or more participating OLSRv2
interfaces. The set of a router's interfaces may change over
Clausen, et al. Expires January 27, 2012 [Page 8]
Internet-Draft OLSRv2 July 2011
time. Each OLSRv2 interface may have one or more network
addresses (which may have prefix lengths), and these may also be
dynamically changing.
o Enables hop-by-hop routing, i.e., each router can use its local
information provided by this protocol to route packets.
o Continuously maintains routes to all destinations in the network,
i.e., routes are instantly available and data traffic is subject
to no delays due to route discovery. Consequently, no data
traffic buffering is required.
o Supports routers that have non-OLSRv2 interfaces which may be
local to a router or that can serve as gateways towards other
networks.
o Enables the use of bidirectional additive link metrics to use
shortest distance (i.e., the total of metrics) routes. Incoming
link metric values are to be determined by a process outside this
specification.
o Is optimized for large and dense networks; the larger and more
dense a network, the more optimization can be achieved by using
MPRs, compared to the classic link state algorithm.
o Uses [RFC5444] as described in its "Intended Usage" appendix and
by [RFC5498].
o Allows "external" and "internal" extensibility as enabled by
[RFC5444].
o Is designed to work in a completely distributed manner, and does
not depend on any central entity.
4. Protocol Overview and Functioning
The objective of this protocol is for each router to, independently:
o Identify all destinations in the network.
o Identify a sufficient subset of links in the network, in order
that shortest paths can be calculated to all available
destinations.
o Provide a Routing Set, containing these shortest paths from this
router to all destinations (routable addresses and local links).
Clausen, et al. Expires January 27, 2012 [Page 9]
Internet-Draft OLSRv2 July 2011
4.1. Overview
These objectives are achieved, for each router, by:
o Using [RFC6130] to identify symmetric 1-hop neighbors and
symmetric 2-hop neighbors.
o Extending [RFC6130] to allow the addition of directional link
metrics to advertised links, and to indicate which link metric
type is being used by that router. Both incoming and outgoing
link metrics may be reported, the latter determined by the
advertising router.
o Independently selecting flooding MPRs and routing MPRs from among
its symmetric 1-hop neighbors such that, for each set of MPRs all
symmetric 2-hop neighbors are reachable via at least one symmetric
1-hop neighbor. An analysis and examples of MPR selection
algorithms is given in [MPR], a suggested algorithm, modified for
each set of MPRs, is included in this specification. Note that it
is not necessary for routers to use the same algorithm in order to
interoperate in the same MANET, but these algorithms must each
have the appropriate properties.
o Signaling its flooding MPR and routing MPR selections by extending
[RFC6130] to report this information in outgoing HELLO messages,
by the addition of MPR Address Block TLV(s) associated with the
appropriate network addresses.
o Extracting its flooding MPR selectors and routing MPR selectors
from received HELLO messages, using the included MPR Address Block
TLV(s).
o Reporting its willingness to be a flooding MPR and to be a routing
MPR in HELLO messages, by the addition on an MPR_WILLING Message
TLV. The router's flooding willingness indicates how willing it
is to participate in MPR flooding and the router's routing
willingness indicates how willing is is to be an intermediate node
for routing, while still being able to be a routing source or
destination.
o Using the message format specified in [RFC5444], specifically
defining a TC (Topology Control) Message Type, used to
periodically signal links between routing MPR selectors and itself
throughout the MANET. This signaling includes suitable direction
router metrics (the best link metric in that direction between
those routers).
Clausen, et al. Expires January 27, 2012 [Page 10]
Internet-Draft OLSRv2 July 2011
o Allowing its TC messages, as well as HELLO messages, to be
included in packets specified in [RFC5444], using the "manet" IP
protocol or UDP port as specified in [RFC5498].
o Diffusing TC messages by using a flooding reduction mechanism,
denoted "MPR flooding"; only the flooding MPRs of a router will
retransmit messages received from (i.e., originated or last
relayed by) that router.
Note that the indicated extensions to [RFC6130] are of forms
permitted by that specification.
This specification defines:
o The requirement to use [RFC6130], its parameters, constants, HELLO
messages, and Information Bases, each as extended in this
specification.
o Two new Information Bases: the Topology Information Base and the
Received Message Information Base.
o TC messages, which are used for MANET wide signaling (using MPR
flooding) of selected topology (link state) information.
o A requirement for each router to have an originator address to be
included in, or deducible from, HELLO messages and TC messages.
o The specification of new Message TLVs and Address Block TLVs that
are used in HELLO messages and TC messages, including for
reporting link metrics and their usage, willingness to be an MPR,
MPR selection, and content sequence number information. Note that
the generation of (incoming) link metric values is to be
undertaken by a process outside this specification. This
specification concerns only the distribution and use of those
metrics.
o The generation of TC messages from the appropriate information in
the Information Bases.
o The updating of the Topology Information Base according to
received TC messages.
o The MPR flooding mechanism, including the inclusion of message
originator address and sequence number to manage duplicate
messages, using information recorded in the Received Message
Information Base.
Clausen, et al. Expires January 27, 2012 [Page 11]
Internet-Draft OLSRv2 July 2011
o The response to other events, such as the expiration of
information in the Information Bases.
This protocol inherits the stability of a link state algorithm, and
has the advantage of having routes immediately available when needed,
due to its proactive nature.
This protocol only interacts with IP through routing table
management, and the use of the sending IP address for IP datagrams
containing OLSRv2 packets.
4.2. Routers and Interfaces
In order for a router to participate in a MANET, it MUST have at
least one, and possibly more, OLSRv2 interfaces. Each OLSRv2
interface:
o Is configured with one or more network addresses, as specified in
[RFC6130]. These addresses MUST each be specific to this router,
and MUST include any address that will be used as the sending
address of any IP packet sent on this OLSRv2 interface.
o Has a number of interface parameters, adding to those specified in
[RFC6130].
o Has an Interface Information Base, extending that specified in
[RFC6130].
o Generates and processes HELLO messages according to [RFC6130],
extended as specified in Section 15.
In addition to a set of OLSRv2 interfaces as described above, each
router:
o May have one or more non-OLSRv2 interfaces and/or local attached
networks for which this router can accept packets. All routable
addresses for which the router is to accept packets MUST be used
as an (OLSRv2 or non-OLSRv2) interface network address or as an
address of a local attached network of the router.
o Has a number of router parameters, adding to those specified in
[RFC6130].
o Has a Local Information Base, extending that specified in
[RFC6130], including selection of an originator address and
recording any locally attached networks.
Clausen, et al. Expires January 27, 2012 [Page 12]
Internet-Draft OLSRv2 July 2011
o Has a Neighbor Information Base, extending that specified in
[RFC6130] to record MPR selection and advertisement information.
o Has a Topology Information Base, recording information received in
TC messages.
o Has a Received Message Information Base, recording information
about received messages to ensure that each TC message is only
processed once, and forwarded at most once on each OLSRv2
interface, by a router.
o Generates and processes TC messages.
4.3. Information Base Overview
Each router maintains the Information Bases described in the
following sections. These are used for describing the protocol in
this specification. An implementation of this protocol MAY maintain
this information in the indicated form, or in any other organization
which offers access to this information. In particular, note that it
is not necessary to remove Tuples from Sets at the exact time
indicated, only to behave as if the Tuples were removed at that time.
4.3.1. Local Information Base
The Local Information Base is specified in [RFC6130], and contains a
router's local configuration. It is extended in this specification
to also record an originator address, and to include a router's:
o Originator Set, containing addresses that were recently used as
this router's originator address, and is used, together with the
router's current originator address, to enable a router to
recognize and discard control traffic which was originated by the
router itself.
o Local Attached Network Set, containing network addresses of
networks to which this router can act as a gateway, and advertises
in its TC messages.
4.3.2. Interface Information Bases
The Interface Information Bases, one for each OLSRv2 interface, are
specified in [RFC6130], and are extended to also record, in each Link
Set, link metric values (incoming and outgoing) and flooding MPR
selector information.
Clausen, et al. Expires January 27, 2012 [Page 13]
Internet-Draft OLSRv2 July 2011
4.3.3. Neighbor Information Base
The Neighbor Information Base is specified in [RFC6130], and is
extended to also record, in the Neighbor Tuple for each neighbor:
o Its originator address.
o Neighbor metric values, these being the minimum of the link metric
values in the indicated directon for all symmetric 1-hop links
with that neighbor.
o Its willingness to be a flooding MPR and to be a routing MPR.
o Whether it has been selected by this router as a flooding MPR or
as a routing MPR, and whether it is a routing MPR selector of this
router. (Whether it is a flooding MPR selector of this neighbor
is recorded in the Interface Information Base.)
o Whether it is to be advertised in TC messages sent by this router.
4.3.4. Topology Information Base
The Topology Information Base in each router contains:
o An Advertising Remote Router Set, recording each other router from
which TC messages have been received. This is used in order to
determine if a received TC message contains fresh or outdated
information; a received TC message is ignored in the latter case.
o A Router Topology Set, recording links between routers in the
MANET, as described by received TC messages.
o A Routable Address Topology Set, recording routable addresses in
the MANET (available as packet destinations) and from which other
router these routable addresses can be directly reached (i.e., in
a single IP hop), as reported by received TC messages.
o An Attached Network Set, recording networks to which a remote
router has advertised that it may act as a gateway. These
networks may be reached in one or more IP hops.
o A Routing Set, recording routes from this router to all available
destinations. The IP routing table is to be updated using this
Routing Set. (A router MAY choose to use any or all destination
network addresses in the Routing Set to update the IP routing
table, this selection is outside the scope of this protocol.)
The purpose of the Topology Information Base is to record information
Clausen, et al. Expires January 27, 2012 [Page 14]
Internet-Draft OLSRv2 July 2011
used, in addition to that in the Local Information Base, the
Interface Information Bases and the Neighbor Information Base, to
construct the Routing Set (which is also included in the Topology
Information Base).
This specification describes the calculation of the Routing Set based
on a Topology Graph constructed in two phases. First, a "backbone"
graph representing the routers in the MANET, and the connectivity
between them, is constructed from the Local Information Base, the
Neighbor Information Base and the Router Topology Set. Second, this
graph is "decorated" with additional destination network addresses
using the Local Information Base, the Routable Address Topology Set
and the Attached Network Set.
The Topology Graph does not need to be recorded in the Topology
Information Base, it can either be constructed as required when the
Routing Set is to be changed, or need not be explicitly constructed
(as illustrated in Appendix B). An implementation MAY construct and
retain the Topology Graph if preferred.
4.3.5. Received Message Information Base
The Received Message Information Base in each router contains:
o A Received Set for each OLSRv2 interface, describing TC messages
received by this router on that OLSRv2 interface.
o A Processed Set, describing TC messages processed by this router.
o A Forwarded Set, describing TC messages forwarded by this router.
The Received Message Information Base serves the MPR flooding
mechanism by ensuring that received messages are forwarded at most
once by a router, and also ensures that received messages are
processed exactly once by a router.
4.4. Signaling Overview
This protocol generates and processes HELLO messages according to
[RFC6130], extended according to Section 15 of this specification to
include an originator address, link metrics, and MPR selection
information.
This protocol specifies a single message type, the TC message. TC
messages are sent by their originating router proactively, at a
regular interval. This interval may be fixed, or may be dynamic, for
example it may be backed off due to congestion or network stability.
TC messages may also be sent as a response to a change in the router
Clausen, et al. Expires January 27, 2012 [Page 15]
Internet-Draft OLSRv2 July 2011
itself, or its advertised 1-hop neighborhood, for example on first
being selected as a routing MPR.
Because TC messages are sent periodically, this protocol is tolerant
of unreliable transmissions of TC messages. Message losses may occur
more frequently in wireless networks due to collisions or other
transmission problems. This protocol MAY use "jitter", randomized
adjustments to message transmission times, to reduce the incidence of
collisions, as specified in [RFC5148].
This protocol is tolerant of out of sequence delivery of TC messages
due to in transit message reordering. Each router maintains an
Advertised Neighbor Sequence Number (ANSN) that is incremented when
its recorded neighbor information that is to be included in its TC
messages changes. This ANSN is included in the router's TC messages.
The recipient of a TC message can used this included ANSN to identify
which of the information it has received is most recent, even if
messages have been reordered while in transit. Only the most recent
information received is used, older information received later is
discarded.
TC messages may be "complete" or "incomplete". A complete TC message
advertises all of the originating router's routing MPR selectors, it
may also advertise other symmetric 1-hop neighbors. Complete TC
messages are generated periodically (and also, optionally, in
response to neighborhood changes). Incomplete TC messages may be
used to report additions to advertised information, without repeating
unchanged information.
TC messages, and HELLO messages as extended by this specification,
include an originator address for the router that created the
message. A TC message reports both the originator addresses and
routable addresses of its advertised neighbors, distinguishing the
two using an Address Block TLV (an address may be both routable and
an originator address). TC messages also report the originator's
locally attached networks.
TC messages are MPR flooded throughout the MANET. A router
retransmits a TC message only if it is received from (i.e.,
originated from or was last relayed by) one of that router's flooding
MPR selectors.
Some TC messages may be MPR flooded over only part of the network,
e.g., allowing a router to ensure that nearer routers are kept more
up to date than distant routers, such as is used in Fisheye State
Routing [FSR] and Fuzzy Sighted Link State routing [FSLS]. This is
enabled using [RFC5497].
Clausen, et al. Expires January 27, 2012 [Page 16]
Internet-Draft OLSRv2 July 2011
TC messages include outgoing neighbor metrics that will be used in
the creation of route metrics.
4.5. Link Metrics
OLSRv1 [RFC3626] created minimum hop routes to destinations. However
in many, if not most, circumstances, better routes (in terms of
quality of service for end users) can be created by use of link
metrics.
OLSRv2, as defined in this specification, allows links to have a
metric (also known as a cost). Link metrics as defined in OLSRv2 are
additive, and the routes that are to be created are minimum length
routes, where the length of a route is defined as the sum of the
metrics of the links in that route.
Link metrics are defined to be directional; the link metric from one
router to another may be different from that on the reverse link.
The link metric is assessed at the receiver, as on a (typically)
wireless link, that is the better informed as to link information.
Both incoming and outgoing link information is used by OLSRv2, the
distinctions in the specification must be clearly followed.
This specification also defines both incoming annd outgoing neighbor
metrics for each symmetric 1-hop neighbor, these being the minimum
value of the link metrics in the same direction for all symmstric
links with that neighbor. Note that this means that all neighbor
metric values are link metric values and that specification of, for
example, link metric value encoding also includes neighbor metric
values.
This specification does not define the nature of the link metric.
However this psecification allows, through use of the type extension
of a defined Address Block TLV, for link metrics with specific
meanings to be defined and either allocated by IANA or privately
used. Each HELLO or TC message carrying link (or neighbor) metrics
thus indicates which link metric information it is carrying, thus
allowing routers to determine if they can interoperate. If link
metrics require additional signaling to determine their values,
whether in HELLO messages or otherwise, then this is permitted but is
outside the scope of this specification.
Users are advised that they should carefully consider how to use link
metrics. In particular they should not simply default to use of all
links with equal metrics (i.e. hop count) without careful
consideration of whether that is advisable or not.
Clausen, et al. Expires January 27, 2012 [Page 17]
Internet-Draft OLSRv2 July 2011
4.6. Routing Set
The purpose of the Routing Set is to determine and record routes
(local interface network address and next hop interface network
address) to all possible routable addresses advertised by this
protocol, as well as of all destinations that are local, i.e., within
one hop, to the router (whether using routable addresses or not).
Only symmetric links are used in such routes.
It is intended that the Routing Set can be used for packet routing,
by using its contents to update IP's routing tables. That update,
and whether any Routing Tuples are not used in IP's routing table, is
outside the scope of this specification.
The signaling in this specification has been designed so that a
"backbone" Topology Graph of routers, each identified by its
originator address, with at most one direct connection between any
pair of routers, can be constructed (from the Neighbor Set and the
Router Topology Set) using a suitable minimum path length algorithm.
This Topology Graph can, then, have other network addresses (routable
or of symmetric 1-hop neighbors) added to it (using the Interface
Information Bases, the Routable Address Topology Set and the Attached
Network Set).
5. Protocol Parameters and Constants
The parameters and constants used in this specification are those
defined in [RFC6130] plus those defined in this section. The
separation in [RFC6130] into interface parameters, router parameters
and constants is also used in this specification.
As for the parameters in [RFC6130], parameters defined in this
specification may be changed dynamically by a router, and need not be
the same on different routers, even in the same MANET, or, for
interface parameters, on different interfaces of the same router.
5.1. Protocol and Port Numbers
This protocol specifies TC messages, which are included in packets as
defined by [RFC5444]. These packets may be sent either using the
"manet" protocol number or the "manet" UDP well-known port number, as
specified in [RFC5498].
TC messages and HELLO messages [RFC6130] SHOULD, in a given
deployment of this protocol, both be using the same of either of IP
or UDP, in order that it is possible to combine messages of both
protocols into the same [RFC5444] packet for transmission.
Clausen, et al. Expires January 27, 2012 [Page 18]
Internet-Draft OLSRv2 July 2011
5.2. Multicast Address
This protocol specifies TC messages, which are included in packets as
defined by [RFC5444]. These packets MAY be transmitted using the
link local multicast address "LL-MANET-Routers", as specified in
[RFC5498].
5.3. Interface Parameters
5.3.1. Received Message Validity Time
The following parameter manages the validity time of recorded
received message information:
RX_HOLD_TIME - is the period after receipt of a message by the
appropriate OLSRv2 interface of this router for which that
information is recorded, in order that the message is recognized
as having been previously received on this OLSRv2 interface.
The following constraints apply to this parameters:
o RX_HOLD_TIME > 0
o RX_HOLD_TIME SHOULD be greater than the maximum difference in time
that a message may take to traverse the MANET, taking into account
any message forwarding jitter as well as propagation, queuing, and
processing delays.
5.4. Router Parameters
5.4.1. Local History Times
The following router parameter manages the time for which local
information is retained:
O_HOLD_TIME - is used to define the time for which a recently used
and replaced originator address is used to recognize the router's
own messages.
The following constraint applies to this parameter:
o O_HOLD_TIME >= 0
5.4.2. Link_Metric_Parameters
All routes found using this specification use a single link metric
type that is specified by the router parameter LINK_METRIC_TYPE,
which may take any value from 0 to 255, inclusive.
Clausen, et al. Expires January 27, 2012 [Page 19]
Internet-Draft OLSRv2 July 2011
5.4.3. Message Intervals
The following parameters regulate TC message transmissions by a
router. TC messages are usually sent periodically, but MAY also be
sent in response to changes in the router's Neighbor Set and/or Local
Attached Network Set. In a highly dynamic network, and with a larger
value of the parameter TC_INTERVAL and a smaller value of the
parameter TC_MIN_INTERVAL, TC messages may be transmitted more often
in response to changes than periodically. However because a router
has no knowledge of, for example, routers remote to it (i.e., beyond
two hops away) joining the network, TC messages MUST NOT be sent
purely responsively.
TC_INTERVAL - is the maximum time between the transmission of two
successive TC messages by this router. When no TC messages are
sent in response to local network changes (by design, or because
the local network is not changing) then TC messages SHOULD be sent
at a regular interval TC_INTERVAL, possibly modified by jitter as
specified in [RFC5148].
TC_MIN_INTERVAL - is the minimum interval between transmission of
two successive TC messages by this router. (This minimum interval
MAY be modified by jitter, as specified in [RFC5148].)
The following constraints apply to these parameters:
o TC_INTERVAL > 0
o TC_MIN_INTERVAL >= 0
o TC_INTERVAL >= TC_MIN_INTERVAL
o If TLVs with Type = INTERVAL_TIME, as defined in [RFC5497], are
included in TC messages, then TC_INTERVAL MUST be representable as
described in [RFC5497].
5.4.4. Advertised Information Validity Times
The following parameters manage the validity time of information
advertised in TC messages:
T_HOLD_TIME - is used to define the minimum value in the TLV with
Type = VALIDITY_TIME included in all TC messages sent by this
router. If a single value of parameter TC_HOP_LIMIT (see
Section 5.4.7) is used then this will be the only value in that
TLV.
Clausen, et al. Expires January 27, 2012 [Page 20]
Internet-Draft OLSRv2 July 2011
A_HOLD_TIME - is the period during which TC messages are sent after
they no longer have any advertised information to report, but are
sent in order to accelerate outdated information removal by other
routers.
The following constraints apply to these parameters:
o T_HOLD_TIME > 0
o A_HOLD_TIME >= 0
o T_HOLD_TIME >= TC_INTERVAL
o If TC messages can be lost, then both T_HOLD_TIME and A_HOLD_TIME
SHOULD be significantly greater than TC_INTERVAL; a value >= 3 x
TC_INTERVAL is RECOMMENDED.
o T_HOLD_TIME MUST be representable as described in [RFC5497].
5.4.5. Processing and Forwarding Validity Times
The following parameters manage the processing and forwarding
validity time of recorded message information:
P_HOLD_TIME is the period after receipt of a message that is
processed by this router for which that information is recorded,
in order that the message is not processed again if received
again.
F_HOLD_TIME is the period after receipt of a message that is
forwarded by this router for which that information is recorded,
in order that the message is not forwarded again if received
again.
The following constraints apply to these parameters:
o P_HOLD_TIME > 0
o F_HOLD_TIME > 0
o Both of these parameters SHOULD be greater than the maximum
difference in time that a message may take to traverse the MANET,
taking into account any message forwarding jitter as well as
propagation, queuing, and processing delays.
Clausen, et al. Expires January 27, 2012 [Page 21]
Internet-Draft OLSRv2 July 2011
5.4.6. Jitter
If jitter, as defined in [RFC5148], is used then the governing jitter
parameters are as follows:
TP_MAXJITTER - represents the value of MAXJITTER used in [RFC5148]
for periodically generated TC messages sent by this router.
TT_MAXJITTER - represents the value of MAXJITTER used in [RFC5148]
for externally triggered TC messages sent by this router.
F_MAXJITTER - represents the default value of MAXJITTER used in
[RFC5148] for messages forwarded by this router. However before
using F_MAXJITTER a router MAY attempt to deduce a more
appropriate value of MAXJITTER, for example based on any TLVs with
Type = INTERVAL_TIME or Type = VALIDITY_TIME contained in the
message to be forwarded.
For constraints on these parameters see [RFC5148].
5.4.7. Hop Limit
The parameter TC_HOP_LIMIT is the hop limit set in each TC message.
TC_HOP_LIMIT MAY be a single fixed value, or MAY be different in TC
messages sent by the same router. However each other router, at any
hop count distance, SHOULD see a regular pattern of TC messages in
order that meaningful values of TLVs with Type = INTERVAL_TIME and
Type = VALIDITY_TIME at each hop count distance can be included as
defined in [RFC5497]. Thus the pattern of TC_HOP_LIMIT SHOULD be
defined to have this property. For example the repeating pattern
(255 4 4) satisfies this property (having period TC_INTERVAL at hop
counts up to 4, inclusive, and 3 x TC_INTERVAL at hop counts greater
than 4), but the repeating pattern (255 255 4 4) does not satisfy
this property because at hop counts greater than 4, message intervals
are alternately TC_INTERVAL and 3 x TC_INTERVAL.
The following constraints apply to this parameter:
o The maximum value of TC_HOP_LIMIT >= the network diameter in hops,
a value of 255 is RECOMMENDED. Note that if using a pattern of
different values of TC_HOP_LIMIT as described above, then only the
maximum value in the pattern is so constrained.
o All values of TC_HOP_LIMIT >= 2.
Clausen, et al. Expires January 27, 2012 [Page 22]
Internet-Draft OLSRv2 July 2011
5.4.8. Willingness
Each router has two willingness parameters: WILL_FLOODING and
WILL_ROUTING, each of which MUST be in the range WILL_NEVER to
WILL_ALWAYS, inclusive.
WILL_FLOODING represents the router's willingness to be selected as a
flooding MPR and hence to participate in MPR flooding, in particular
of TC messages.
WILL_ROUTING represents the router's willingness to be selected as a
routing MPR and hence to be an intermediate router on routes.
In either case, the higher the value, the greater the router's
willingness to be a flooding or routing MPR, respectively. If a
router has a willingness value of WILL_NEVER (the lowest possible
value) it does not perform the corresponding task. A MANET using
this protocol with too many routers having either willingness value
equal to WILL_NEVER will not function; it MUST be ensured, by
administrative or other means, that this does not happen.
If a router has a willingness value equal to WILL_ALWAYS (the highest
possible value) then it will always be selected as a flooding or
routing MPR, respectively, by all symmetric 1-hop neighbors.
A MANET in which all routers have WILL_FLOODING = WILL_ALWAYS, the
flooding operation will effectively disable optimizations, and
perform as classic flooding.
A router, which has WILL_ROUTING = WILL_NEVER will not act as an
intermediate router in the MANET. Such a router can, act as a
source, destination or gateway to another routing domain.
Different routers MAY have different values for WILL_FLOODING and/or
WILL_ROUTING. A router that has both WILL_FLOODING = WILL_DEFAULT
and WILL_ROUTING = WILL_DEFAULT need not include an MPR_WILLING TLV
in its HELLO messages.
The following constraints apply to these parameters:
o WILL_FLOODING >= WILL_NEVER
o WILL_FLOODING <= WILL_ALWAYS
o WILL_ROUTING >= WILL_NEVER
o WILL_ROUTING <= WILL_ALWAYS
Clausen, et al. Expires January 27, 2012 [Page 23]
Internet-Draft OLSRv2 July 2011
5.5. Parameter Change Constraints
If protocol parameters are changed dynamically, then the constraints
in this section apply.
RX_HOLD_TIME
* If RX_HOLD_TIME for an OLSRv2 interface changes, then the
expiry time for all Received Tuples for that OLSRv2 interface
MAY be changed.
O_HOLD_TIME
* If O_HOLD_TIME for a router changes, then the expiry time for
all Originator Tuples MAY be changed.
TC_INTERVAL
* If the TC_INTERVAL for a router increases, then the next TC
message generated by this router MUST be generated according to
the previous, shorter, TC_INTERVAL. Additional subsequent TC
messages MAY be generated according to the previous, shorter,
TC_INTERVAL.
* If the TC_INTERVAL for a router decreases, then the following
TC messages from this router MUST be generated according to the
current, shorter, TC_INTERVAL.
P_HOLD_TIME
* If P_HOLD_TIME changes, then the expiry time for all Processed
Tuples MAY be changed.
F_HOLD_TIME
* If F_HOLD_TIME changes, then the expiry time for all Forwarded
Tuples MAY be changed.
TP_MAXJITTER
* If TP_MAXJITTER changes, then the periodic TC message schedule
on this router MAY be changed immediately.
TT_MAXJITTER
* If TT_MAXJITTER changes, then externally triggered TC messages
on this router MAY be rescheduled.
Clausen, et al. Expires January 27, 2012 [Page 24]
Internet-Draft OLSRv2 July 2011
F_MAXJITTER
* If F_MAXJITTER changes, then TC messages waiting to be
forwarded with a delay based on this parameter MAY be
rescheduled.
TC_HOP_LIMIT
* If TC_HOP_LIMIT changes, and the router uses multiple values
after the change, then message intervals and validity times
included in TC messages MUST be respected. The simplest way to
do this is to start any new repeating pattern of TC_HOP_LIMIT
values with its largest value.
LINK_METRIC_TYPE
* If LINK_METRIC_TYPE changes then all link metric information
recorded by the router is invalid. The router MUST take the
following actions, and all consequent actions described in
Section 17 and [RFC6130].
+ For each Link Tuple in any Link Set, either update
L_in_metric (the value MAXIMUM_METRIC MAY be used) or remove
the Link Tuple from the Link Set.
+ For each Link Tuple that is not removed, set:
- L_out_metric := UNKNOWN_METRIC;
- L_SYM_time := expired;
- L_MPR_selector := false.
+ Remove all Router Topology Tuples, Routable Address Topology
Tuples, Attached Network Tuples and Routing Tuples from
their respective protocol sets in the Topology Information
Base.
5.6. Constants
5.6.1. Link Metric Constants
The constant minimum, maximum and default metric values are defined
by:
o MINIMUM_METRIC := 1
Clausen, et al. Expires January 27, 2012 [Page 25]
Internet-Draft OLSRv2 July 2011
o MAXIMUM_METRIC := 16776960
o DEFAULT_METRIC := 256
The symbolic value UNKNOWN_METRIC is defined in Section 6.1.
6. Link Metric Values
A router records a link metric value for each direction of a link of
which it has knowledge. These link metric values are used to create
metrics for routes by the addition of link metric values.
6.1. Link Metric Representation
Link metric are reported in messages using a compressed
representation that occupies 12 bits, a 4 bit field and an 8 bit
field. The compressed representation represents positive integer
values with a minimum value of 1 and a maximum value that is slightly
smaller than the maximum 24 bit value. Only those values that have
exact representation in the compressed form are used. Route metrics
are the summation of no more then 255 link metric values, and can
therefore be represented using no more than 32 bits.
Link and route metrics used in the Information Bases defined in this
specification refer to the uncompressed values, and arithmetic
involving them does likewise, and assumes full precision in the
result. (How an implementation records the values is not part of
this specification, as long as it behaves as if recording
uncompressed values. An implementation can, for example, use 32 bit
values for all link and route metrics.)
In some cases a link metric value may be unknown. This is indicated
in this specification by the value UNKNOWN_METRIC. An implementation
may use any representation of UNKNOWN_METRIC as it is never included
in messages or used in any computation. (Possible values are zero,
or any value greater than the maximum representable metric value.)
6.2. Link Metric Compressed Form
The 12-bit compressed form of a link metric uses a modified form of a
representation with as 8-bit mantissa (denoted b) and a 4-bit
exponent (denoted a). Note that if represented as the 12 bit value
256a+b then the ordering of those 12 bit values is identical to the
ordering of the represented values.
The value so represented is (257+b)2^a - 256, where ^ denotes
exponentiation. This has a minimum value (when a = 0 and b = 0) of
MINUMUM_METRIC = 1 and a maximum value (when a = 15 and b = 255) of
Clausen, et al. Expires January 27, 2012 [Page 26]
Internet-Draft OLSRv2 July 2011
MAXIMUM_METRIC = 2^24 - 256.
An algorithm for computing a and b for the smallest representable
value not less than a link metric value v such that MINIMUM_METRIC <=
v <= MAXIMUM_METRIC is:
1. Find the smallest integer a such that v + 256 <= 2^(a + 9).
2. Set b := (v - 256(2^a - 1)) / (2^a) - 1, rounded up to the
nearest integer.
To allow for more efficient messages, a default link metric
DEFAULT_METRIC is defined, which can be omitted from messages. Note
that this is not the same as the link metric value that should be
used when this specification requires a link metric, but no
information about a link, beyond that a HELLO message has been
received using that link, is available. In this case the link metric
used SHOULD be MAXIMUM_METRIC.
7. Local Information Base
The Local Information Base, as defined for each router in [RFC6130],
is extended by this protocol by:
o Recording the router's originator address. The originator address
MUST be unique to this router. It MUST NOT be used by any other
router as an originator address. It MAY be included in any
network address in any I_local_iface_addr_list of this router, it
MUST NOT be included in any network address in any
I_local_iface_addr_list of any other router. It MAY be included
in, but MUST NOT be equal to, the AL_net_addr in any Local
Attached Network Tuple in this or any other router.
o The addition of an Originator Set, defined in Section 7.1, and a
Local Attached Network Set, defined in Section 7.2.
All routable addresses of the router for which it is to accept
packets as destination MUST be included in the Local Interface Set or
the Local Attached Network Set.
7.1. Originator Set
A router's Originator Set records addresses that were recently used
as originator addresses by this router. If a router's originator
address is immutable then this set is always empty and MAY be
omitted. It consists of Originator Tuples:
(O_orig_addr, O_time)
Clausen, et al. Expires January 27, 2012 [Page 27]
Internet-Draft OLSRv2 July 2011
where:
O_orig_addr - is a recently used originator address, note that this
does not include a prefix length;
O_time - specifies the time at which this Tuple expires and MUST be
removed.
7.2. Local Attached Network Set
A router's Local Attached Network Set records its local non-OLSRv2
interfaces via which it can act as gateways to other networks. The
Local Attached Network Set is not modified by this protocol. This
protocol MAY respond to changes to the Local Attached Network Set,
which MUST reflect corresponding changes in the router's status. It
consists of Local Attached Network Tuples:
(AL_net_addr, AL_dist, AL_metric)
where:
AL_net_addr - is the network address of an attached network which
can be reached via this router. This SHOULD be a routable
address. It is constrained as described below.
AL_dist - is the number of hops to the network with network address
AL_net_addr from this router.
AL_metric - is the metric of the link to the attached network with
address AL_net_addr from this router;
Attached networks local to this router only (i.e., not reachable
except via this router) SHOULD be treated as local non-MANET
interfaces, and added to the Local Interface Set, as specified in
[RFC6130], rather than be added to the Local Attached Network Set.
Because an attached network is not specific to the router, and may be
outside the MANET, an attached network MAY also be attached to other
routers. Routing to an AL_net_addr will use maximum prefix length
matching; consequently an AL_net_addr MAY include, but MUST NOT equal
or be included in, any network address which is of any interface of
any router (i.e., is included in any I_local_iface_addr_list) or
equal any router's originator address.
It is not the responsibility of this protocol to maintain routes from
this router to networks recorded in the Local Attached Network Set.
Local Attached Neighbor Tuples are removed from the Local Attached
Clausen, et al. Expires January 27, 2012 [Page 28]
Internet-Draft OLSRv2 July 2011
Network Set only when the routers' local attached network
configuration changes, i.e., they are not subject to timer-based
expiration or changes due to received messages.
8. Interface Information Base
An Interface Information Base, as defined in [RFC6130], is maintained
for each OLSRv2 interface. Its Link Set and 2-Hop Set are modified
by this protocol.
The Link Set is modified by adding these additional elements to each
Link Tuple:
L_in_metric - is the metric of the link from the OLSRv2 interface
with addresses L_neighbor_iface_addr_list to this OLSRv2
interface;
L_out_metric - is the metric of the link to the OLSRv2 interface
with addresses L_neighbor_iface_addr_list from this OLSRv2
interface;
L_mpr_selector - is a boolean flag, describing if this neighbor has
selected this router as a flooding MPR, i.e., is a flooding MPR
selector of this router.
L_in_metric will be specified by a process that is external to this
specification. Any Link Tuple with L_status = HEARD or L_status =
SYMMETRIC MUST have a specified value of L_in_metric.
A Link Tuple created (but not updated) by [RFC6130] MUST set:
o L_in_metric := unknown;
o L_out_metric := unknown;
o L_mpr_selector := false.
The 2-Hop Set is modified by adding these additional elements to each
2-Hop Tuple:
N2_in_metric - is the router metric from the router with address
N2_2hop_iface_addr to the router with OLSRv2 interface addresses
N2_neighbor_iface_addr_list;
N2_out_metric - is the router metric to the router with address
N2_2hop_iface_addr from the router with OLSRv2 interface addresses
N2_neighbor_iface_addr_list.
Clausen, et al. Expires January 27, 2012 [Page 29]
Internet-Draft OLSRv2 July 2011
A Neighbor Tuple created (but not updated) by [RFC6130] MUST set:
o N2_in_metric := unknown;
o N2_out_metric := unknown.
9. Neighbor Information Base
An Neighbor Information Base, as defined in [RFC6130], is maintained
for each router. It is modified by this protocol by adding these
additional elements to each Neighbor Tuple in the Neighbor Set:
N_orig_addr - is the neighbor's originator address, which may be
unknown. Note that this originator address does not include a
prefix length;
N_in_metric - is the router metric of any link from this neighbor to
this router, i.e., the minimum of all corresponding L_in_metric
with L_status = SYMMETRIC, unspecified if there are no such Link
Tuples;
N_out_metric - is the router metric of any link from this router to
this neighbor, i.e., the minimum of all corresponding L_out_metric
with L_status = SYMMETRIC, unspecified if there are no such Link
Tuples;
N_will_flooding - is the neighbor's willingness to be selected as a
flooding MPR, in the range from WILL_NEVER to WILL_ALWAYS, both
inclusive;
N_will_routing - is the neighbor's willingness to be selected as a
routing MPR, in the range from WILL_NEVER to WILL_ALWAYS, both
inclusive;
N_flooding_mpr - is a boolean flag, describing if this neighbor is
selected as a flooding MPR by this router;
N_routing_mpr - is a boolean flag, describing if this neighbor is
selected as a routing MPR by this router;
N_mpr_selector - is a boolean flag, describing if this neighbor has
selected this router as a routing MPR, i.e., is a routing MPR
selector of this router.
N_advertised - is a boolean flag, describing if this router has
elected to advertise a link to this neighbor in its TC messages.
A Neighbor Tuple created (but not updated) by [RFC6130] MUST set:
Clausen, et al. Expires January 27, 2012 [Page 30]
Internet-Draft OLSRv2 July 2011
o N_orig_addr := unknown;
o N_in_metric := unknown;
o N_out_metric := unknown;
o N_will_flooding := WILL_NEVER;
o N_will_routing := WILL_NEVER;
o N_routing_mpr := false;
o N_flooding_mpr := false;
o N_mpr_selector := false;
o N_advertised := false.
The Neighbor Information Base also includes a variable, the
Advertised Neighbor Sequence Number (ANSN), whose value is included
in TC messages to indicate the freshness of the information
transmitted. The ANSN is incremented whenever advertised information
(the originator and routable addresses included in Neighbor Tuples
with N_advertised = true, and local attached networks recorded in the
Local Attached Network Set in the Local Information Base) changes,
including addition or removal of such information.
10. Topology Information Base
The Topology Information Base, defined for each router by this
specification, stores information received in TC messages, in the
Advertising Remote Router Set, the Router Topology Set, the Routable
Address Topology Set and the Attached Network Set.
Additionally, a Routing Set is maintained, derived from the
information recorded in the Local Information Base, the Interface
Information Bases, the Neighbor Information Base and the rest of the
Topology Information Base.
10.1. Advertising Remote Router Set
A router's Advertising Remote Router Set records information
describing each remote router in the network that transmits TC
messages, allowing outdated TC messages to be recognized and
discarded. It consists of Advertising Remote Router Tuples:
(AR_orig_addr, AR_seq_number, AR_time)
Clausen, et al. Expires January 27, 2012 [Page 31]
Internet-Draft OLSRv2 July 2011
where:
AR_orig_addr - is the originator address of a received TC message,
note that this does not include a prefix length;
AR_seq_number - is the greatest ANSN in any TC message received
which originated from the router with originator address
AR_orig_addr (i.e., which contributed to the information contained
in this Tuple);
AR_time - is the time at which this Tuple expires and MUST be
removed.
10.2. Router Topology Set
A router's Topology Set records topology information about the links
between routers in the MANET. It consists of Router Topology Tuples:
(TR_from_orig_addr, TR_to_orig_addr, TR_seq_number, TR_metric,
TR_time)
where:
TR_from_orig_addr - is the originator address of a router which can
reach the router with originator address TR_to_orig_addr in one
hop, note that this does not include a prefix length;
TR_to_orig_addr - is the originator address of a router which can be
reached by the router with originator address TR_to_orig_addr in
one hop, note that this does not include a prefix length;
TR_seq_number - is the greatest ANSN in any TC message received
which originated from the router with originator address
TR_from_orig_addr (i.e., which contributed to the information
contained in this Tuple);
TR_metric - is the router metric from the router with originator
address TR_from_orig_addr to the router with originator address
TR_to_orig_addr;
TR_time - specifies the time at which this Tuple expires and MUST be
removed.
10.3. Routable Address Topology Set
A router's Routable Address Topology Set records topology information
about the routable addresses within the MANET, and via which routers
they may be reached. It consists of Routable Address Topology
Clausen, et al. Expires January 27, 2012 [Page 32]
Internet-Draft OLSRv2 July 2011
Tuples:
(TA_from_orig_addr, TA_dest_addr, TA_seq_number, TA_metric,
TA_time)
where:
TA_from_orig_addr - is the originator address of a router which can
reach the router with routable address TA_dest_addr in one hop,
note that this does not include a prefix length;
TA_dest_addr - is a routable address of a router which can be
reached by the router with originator address TA_from_orig_addr in
one hop;
TA_seq_number - is the greatest ANSN in any TC message received
which originated from the router with originator address
TA_from_orig_addr (i.e., which contributed to the information
contained in this Tuple);
TA_metric - is the router metric from the router with originator
address TA_from_orig_addr to the router with OLSRv2 interface
address TA_dest_addr;
TA_time - specifies the time at which this Tuple expires and MUST be
removed.
10.4. Attached Network Set
A router's Attached Network Set records information about networks
(which may be outside the MANET) attached to other routers and their
routable addresses. It consists of Attached Network Tuples:
(AN_orig_addr, AN_net_addr, AN_seq_number, AN_dist, AN_metric,
AN_time)
where:
AN_orig_addr - is the originator address of a router which can act
as gateway to the network with network address AN_net_addr, note
that this does not include a prefix length;
AN_net_addr - is the network address of an attached network, which
may be reached via the router with originator address
AN_orig_addr;
Clausen, et al. Expires January 27, 2012 [Page 33]
Internet-Draft OLSRv2 July 2011
AN_seq_number - is the greatest ANSN in any TC message received
which originated from the router with originator address
AN_orig_addr (i.e., which contributed to the information contained
in this Tuple);
AN_dist - is the number of hops to the network with network address
AN_net_addr from the router with originator address AN_orig_addr;
AN_metric - is the metric of the link from the router with
originator address AN_orig_addr to the attached network with
address AN_net_addr;
AN_time - specifies the time at which this Tuple expires and MUST be
removed.
10.5. Routing Set
A router's Routing Set records the first hop along a selected path to
each destination for which any such path is known. It consists of
Routing Tuples:
(R_dest_addr, R_next_iface_addr, R_local_iface_addr, R_dist,
R_metric)
where:
R_dest_addr - is the network address of the destination, either the
network address of an interface of a destination router, or the
network address of an attached network;
R_next_iface_addr - is the network address of the "next hop" on the
selected path to the destination;
R_local_iface_addr - is the network address of the local OLSRv2
interface over which a packet MUST be sent to reach the
destination by the selected path.
R_dist - is the number of hops on the selected path to the
destination;
R_metric - is the metric of the route to the destination with
address R_dest_addr.
The Routing Set for a router is derived from the contents of other
protocol Sets of the router (the Link Sets, the Neighbor Set, the
Router Topology Set, the Routable Address Topology Set, the Attached
Network Set, and OPTIONALLY the Two Hop Sets). The Routing Set is
updated (Routing Tuples added or removed, or the complete Routing Set
Clausen, et al. Expires January 27, 2012 [Page 34]
Internet-Draft OLSRv2 July 2011
recalculated) when routing paths are calculated, based on changes to
these other protocol Sets. Routing Tuples are not subject to timer-
based expiration.
11. Received Message Information Base
The Received Message Information Base, defined by this specification,
records information required to ensure that a message is processed at
most once and is forwarded at most once per OLSRv2 interface of a
router, using MPR flooding.
11.1. Received Set
A router has a Received Set per OLSRv2 interface. Each Received Set
records the signatures of messages which have been received over that
OLSRv2 interface. Each consists of Received Tuples:
(RX_type, RX_orig_addr, RX_seq_number, RX_time)
where:
RX_type - is the received Message Type;
RX_orig_addr - is the originator address of the received message,
note that this does not include a prefix length;
RX_seq_number - is the message sequence number of the received
message;
RX_time - specifies the time at which this Tuple expires and MUST be
removed.
11.2. Processed Set
A router has a single Processed Set which records signatures of
messages which have been processed by the router. It consists of
Processed Tuples:
(P_type, P_orig_addr, P_seq_number, P_time)
where:
P_type - is the processed Message Type;
P_orig_addr - is the originator address of the processed message,
note that this does not include a prefix length;
Clausen, et al. Expires January 27, 2012 [Page 35]
Internet-Draft OLSRv2 July 2011
P_seq_number - is the message sequence number of the processed
message;
P_time - specifies the time at which this Tuple expires and MUST be
removed.
11.3. Forwarded Set
A router has a single Forwarded Set which records signatures of
messages which have been forwarded by the router. It consists of
Forwarded Tuples:
(F_type, F_orig_addr, F_seq_number, F_time)
where:
F_type - is the forwarded Message Type;
F_orig_addr - is the originator address of the forwarded message,
note that this does not include a prefix length;
F_seq_number - is the message sequence number of the forwarded
message;
F_time - specifies the time at which this Tuple expires and MUST be
removed.
12. Information Base Properties
As part of this specification, in a number of cases there is a
natural correspondence from a Protocol Tuple in one Protocol Set to a
single Protocol Tuple in another Protocol Set, in the same or another
Information Base. The latter Protocol Tuple is referred to as
"corresponding" to the former Protocol Tuple.
Specific examples of corresponding Protocol Tuples include:
o There is a Local Interface Tuple corresponding to each Link Tuple,
where the Link Tuple is in the Link Set for an OLSRv2 interface,
and the Local Interface Tuple represents that OLSRv2 interface.
o There is a Neighbor Tuple corresponding to each Link Tuple which
has L_HEARD_time not expired, such that N_neighbor_addr_list
contains L_neighbor_iface_addr_list.
o There is a Link Tuple (in the Link Set in the same Interface
Information Base) corresponding to each 2-Hop Tuple such that
L_neighbor_iface_addr_list = N2_neighbor_iface_addr_list.
Clausen, et al. Expires January 27, 2012 [Page 36]
Internet-Draft OLSRv2 July 2011
o There is a Neighbor Tuple corresponding to each 2-Hop Tuple, such
that N_neighbor_addr_list contains N2_neighbor_iface_addr_list.
(This is the Neighbor Tuple corresponding to the Link Tuple that
corresponds to the 2-Hop Tuple.)
o There is an Advertising Remote Router Tuple corresponding to each
Router Topology Tuple such that AR_orig_addr = TR_from_orig_addr.
o There is an Advertising Remote Router Tuple corresponding to each
Routable Address Topology Tuple such that AR_orig_addr =
TA_from_orig_addr.
o There is an Advertising Remote Router Tuple corresponding to each
Attached Network Tuple such that AR_orig_addr = AN_orig_addr.
o There is an Neighbor Tuple corresponding to each Routing Tuple
such that N_neighbor_addr_list contains R_next_iface_addr.
Addresses or network addresses with the following properties are
considered as "fully owned" by a router when processing a received
message:
o Equaling its originator address, OR;
o Equaling the O_orig_addr in an Originator Tuple, OR;
o Equaling or being a sub-range of the I_local_iface_addr_list in a
Local Interface Tuple, OR;
o Equaling or being a sub-range of the IR_local_iface_addr in a
Removed Interface Address Tuple, OR;
o Equaling an AL_net_addr in a Local Attached Network Tuple.
Addresses or network addresses with the following properties are
considered as "partially owned" (which may include being fully owned)
by a router when processing a received message:
o Overlapping (equaling or containing) its originator address, OR;
o Overlapping (equaling or containing) the O_orig_addr in an
Originator Tuple, OR;
o Overlapping the I_local_iface_addr_list in a Local Interface
Tuple, OR;
o Overlapping the IR_local_iface_addr in a Removed Interface Address
Tuple, OR;
Clausen, et al. Expires January 27, 2012 [Page 37]
Internet-Draft OLSRv2 July 2011
o Equaling or having as a sub-range an AL_net_addr in a Local
Attached Network Tuple.
13. Packets and Messages
The packet and message format used by this protocol is defined in
[RFC5444]. Except as otherwise noted, options defined in [RFC5444]
may be freely used, in particular alternative formats defined by
packet, message, Address Block and TLV flags.
This section describes the usage of the packets and messages defined
in [RFC5444] by this specification, and the TLVs defined by, and used
in, this specification.
13.1. Messages
Routers using this protocol exchange information through messages.
The message types used by this protocol are the HELLO message and the
TC message. The HELLO message is defined by [RFC6130] and extended
by this specification, see Section 15. The TC message is defined by
this specification, see Section 16.
13.2. Packets
One or more messages sent by a router at the same time SHOULD be
combined into a single packet, subject to any constraints on maximum
packet size (such as derived from the MTU over a local single hop)
that MAY be imposed. These messages may have originated at the
sending router, or have originated at another router and are being
forwarded by the sending router. Messages with different originating
routers MAY be combined for transmission within the same packet.
Messages from other protocols defined using [RFC5444], including but
not limited to [RFC6130], MAY be combined for transmission within the
same packet. This specification does not define or use any contents
of the Packet Header.
Forwarded messages MAY be jittered as described in [RFC5148],
including the observation that the forwarding jitter of all messages
received in a single packet SHOULD be the same. The value of
MAXJITTER used in jittering a forwarded message MAY be based on
information in that message (in particular any Message TLVs with Type
= INTERVAL_TIME or Type = VALIDITY_TIME) or otherwise SHOULD be with
a maximum delay of F_MAXJITTER. A router MAY modify the jitter
applied to a message in order to more efficiently combine messages in
packets, as long as the maximum jitter is not exceeded.
Clausen, et al. Expires January 27, 2012 [Page 38]
Internet-Draft OLSRv2 July 2011
13.3. TLVs
This specification defines 2 Message TLVs and 4 Address Block TLVs.
All references in this specification to TLVs that do not indicate a
type extension, assume Type Extension = 0. TLVs in processed
messages with a type extension which is neither zero as so assumed,
nor a specifically indicated non-zero type extension, are ignored.
13.3.1. Message TLVs
The MPR_WILLING TLV is used in HELLO messages. At most one
MPR_WILLING TLV may appear in any message.
+-------------+--------------+--------------------------------------+
| Type | Value Length | Value |
+-------------+--------------+--------------------------------------+
| MPR_WILLING | 1 octet | Bits 0-3 encode the parameter |
| | | WILL_FLOODING; bits 4-7 encode the |
| | | parameter WILL_ROUTING. |
+-------------+--------------+--------------------------------------+
Table 1: MPR_WILLING TLV definition
The CONT_SEQ_NUM TLV is used in TC messages. At most one
CONT_SEQ_NUM TLV may appear in any message.
+--------------+--------------+-------------------------------------+
| Type | Value Length | Value |
+--------------+--------------+-------------------------------------+
| CONT_SEQ_NUM | 2 octets | The ANSN contained in the Neighbor |
| | | Information Base. |
+--------------+--------------+-------------------------------------+
Table 2: CONT_SEQ_NUM TLV definition
13.3.2. Address Block TLVs
The LINK_METRIC TLV is used in HELLO messages and TC messages. It
may use any type extension; only LINK_METRIC TLVs with type extension
equal to LINK_METRIC_TYPE will be used by this specification. At
most one link metric value of any given kind (link or neighbor) and
direction may be associated with any address.
Clausen, et al. Expires January 27, 2012 [Page 39]
Internet-Draft OLSRv2 July 2011
+-------------+--------------+--------------------------------------+
| Type | Value Length | Value |
+-------------+--------------+--------------------------------------+
| LINK_METRIC | 2 octets | Bits 0-3 indicates kind(s) and |
| | | direction(s), Bits 4-7 indicate |
| | | exponent (a), Bits 8-15 indicate |
| | | mantissa (b) |
+-------------+--------------+--------------------------------------+
Table 3: LINK_METRIC TLV definition
The exponent and mantissa use the representation defined in
Section 6. Each bit of the types and directions sub-field, if set
('1') indicates that the link metric is of the indicated kind and
direction. Any combination of these bits MAY be used, except that
the combination with all bits unset ('0') SHOULD NOT be used.
+-----+-----------------+-----------+
| Bit | Kind | Direction |
+-----+-----------------+-----------+
| 0 | Link metric | Incoming |
| 1 | Link metric | Outgoing |
| 2 | Neighbor metric | Incoming |
| 3 | Neighbor metric | Outgoing |
+-----+-----------------+-----------+
Table 4: LINK_METRIC TLV types and directions
The MPR TLV is used in HELLO messages, and indicates that an address
with which it is associated is of a symmetric 1-hop neighbor that has
been selected as an MPR.
+------+--------------+---------------------------------------------+
| Type | Value Length | Value |
+------+--------------+---------------------------------------------+
| MPR | 1 octet | FLOODING indicates that the corresponding |
| | | address is of a neighbor selected as a |
| | | flooding MPR, ROUTING indicates that the |
| | | corresponding address is of a neighbor |
| | | selected as a routing MPR, FLOOD_ROUTE |
| | | indicates both |
+------+--------------+---------------------------------------------+
Table 5: MPR TLV definition
The NBR_ADDR_TYPE TLV is used in TC messages.
Clausen, et al. Expires January 27, 2012 [Page 40]
Internet-Draft OLSRv2 July 2011
+---------------+--------------+------------------------------------+
| Type | Value Length | Value |
+---------------+--------------+------------------------------------+
| NBR_ADDR_TYPE | 1 octet | ORIGINATOR indicates that the |
| | | corresponding address (which MUST |
| | | have maximum prefix length) is an |
| | | originator address, ROUTABLE |
| | | indicates that the corresponding |
| | | network address is a routable |
| | | address of an interface, |
| | | ROUTABLE_ORIG indicates that the |
| | | corresponding address is both |
+---------------+--------------+------------------------------------+
Table 6: NBR_ADDR_TYPE TLV definition
If an address is both a originator address and a routable address,
then it may be associated with either one Address Block TLV with Type
:= NBR_ADDR_TYPE and Value := ROUTABLE_ORIG, or with two Address
Block TLVs with Type:= NBR_ADDR_TYPE, one with Value := ORIGINATOR
and one with Value := ROUTABLE.
The GATEWAY TLV is used in TC messages. At most one GATEWAY TLV may
be associated with any address.
+---------+--------------+-------------------------------------+
| Type | Value Length | Value |
+---------+--------------+-------------------------------------+
| GATEWAY | 1 octet | Number of hops to attached network. |
+---------+--------------+-------------------------------------+
Table 7: GATEWAY TLV definition
All address objects included in a TC message according to this
specification MUST be associated either with at least one TLV with
Type := NBR_ADDR_TYPE or with a TLV with Type := GATEWAY, but not
both. Any other address objects MAY be included in Address Blocks in
a TC message, but are ignored by this specification.
14. Message Processing and Forwarding
This section describes the optimized flooding operation (MPR
flooding) used when control messages, as instances of [RFC5444], are
intended for MANET wide distribution. This flooding mechanism
defines when a received message is, or is not, processed and/or
forwarded.
This flooding mechanism is used by this protocol and MAY be used by
Clausen, et al. Expires January 27, 2012 [Page 41]
Internet-Draft OLSRv2 July 2011
extensions to this protocol which define, and hence own, other
message types, to manage processing and/or forwarding of these
messages. This specification contains elements (P_type, RX_type,
F_type) required only for such usage.
This flooding mechanism is always used for TC messages (see
Section 16). Received HELLO messages (see Section 15 are, unless
invalid, always processed, and never forwarded by this flooding
mechanism. They thus do not need to be recorded in the Received
Message Information Base.
The processing selection and forwarding mechanisms are designed to
only need to parse the Message Header in order to determine whether a
message is to be processed and/or forwarded, and not to have to parse
the Message Body even if the message is forwarded (but not
processed). An implementation MAY only parse the Message Body if
necessary, or MAY always parse the Message Body and reject the
message if it cannot be so parsed, or any other error is identified.
An implementation MUST discard the message silently if it is unable
to parse the Message Header or (if attempted) the Message Body, or if
a message (other than a HELLO message) does not include a message
sequence number.
14.1. Actions when Receiving a Message
On receiving a message of a type specified to be using this
mechanism, which includes the TC messages defined in this
specification, a router MUST perform the following:
1. If the router recognizes from the originator address of the
message that the message is one which the receiving router itself
originated (i.e., the message originator address is the
originator address of this router, or is an O_orig_addr in an
Originator Tuple) then the message MUST be silently discarded.
2. Otherwise:
1. If the message is of a type which may be processed, then the
message is considered for processing according to
Section 14.2.
2. If the message is of a type which may be forwarded, AND:
+ <msg-hop-limit> is present and <msg-hop-limit> > 1, AND;
+ <msg-hop-count> is not present or <msg-hop-count> < 255;
Clausen, et al. Expires January 27, 2012 [Page 42]
Internet-Draft OLSRv2 July 2011
then the message is considered for forwarding according to
Section 14.3.
14.2. Message Considered for Processing
If a message (the "current message") is considered for processing,
then the following tasks MUST be performed:
1. If the sending address (i.e., the source address of the IP
datagram containing the current message) does not match (taking
into account any address prefix) a network address in an
L_neighbor_iface_addr_list of a Link Tuple, with L_status =
SYMMETRIC, in the Link Set for the OLSRv2 interface on which the
current message was received (the "receiving interface") then
processing the current message is OPTIONAL. If the current
message is not processed then the following steps are not carried
out.
2. If a Processed Tuple exists with:
* P_type = the Message Type of the current message, AND;
* P_orig_addr = the originator address of the current message,
AND;
* P_seq_number = the message sequence number of the current
message;
then the current message MUST NOT be processed.
3. Otherwise:
1. Create a Processed Tuple with:
+ P_type := the Message Type of the current message;
+ P_orig_addr := the originator address of the current
message;
+ P_seq_number := the sequence number of the current
message;
+ P_time := current time + P_HOLD_TIME.
2. Process the current message according to its Message Type.
For a TC message this is as defined in Section 16.3.
Clausen, et al. Expires January 27, 2012 [Page 43]
Internet-Draft OLSRv2 July 2011
14.3. Message Considered for Forwarding
If a message (the "current message") is considered for forwarding,
then the following tasks MUST be performed:
1. If the sending address (i.e., the source address of the IP
datagram containing the current message) does not match (taking
into account any address prefix) a network address in an
L_neighbor_iface_addr_list of a Link Tuple, with L_status =
SYMMETRIC, in the Link Set for the OLSRv2 interface on which the
current message was received (the "receiving interface") then the
current message MUST be silently discarded.
2. Otherwise:
1. If a Received Tuple exists in the Received Set for the
receiving interface, with:
+ RX_type = the Message Type of the current message, AND;
+ RX_orig_addr = the originator address of the current
message, AND;
+ RX_seq_number = the sequence number of the current
message;
then the current message MUST be silently discarded.
2. Otherwise:
1. Create a Received Tuple in the Received Set for the
receiving interface with:
- RX_type := the Message Type of the current message;
- RX_orig_addr := originator address of the current
message;
- RX_seq_number := sequence number of the current
message;
- RX_time := current time + RX_HOLD_TIME.
2. If a Forwarded Tuple exists with:
- F_type = the Message Type of the current message, AND;
Clausen, et al. Expires January 27, 2012 [Page 44]
Internet-Draft OLSRv2 July 2011
- F_orig_addr = the originator address of the current
message, AND;
- F_seq_number = the sequence number of the current
message.
then the current message MUST be silently discarded.
3. Otherwise if the sending address matches (taking account
of any address prefix) any network address in an
L_neighbor_iface_addr_list of a Link Tuple in the Link
Set for the receiving OLSRv2 interface that has L_status
= SYMMETRIC and whose corresponding Neighbor Tuple has
N_mpr_selector = true, then:
1. Create a Forwarded Tuple with:
o F_type := the Message Type of the current message;
o F_orig_addr := originator address of the current
message;
o F_seq_number := sequence number of the current
message;
o F_time := current time + F_HOLD_TIME.
2. The Message Header of the current message is modified
by:
o if present, decrement <msg-hop-limit> in the
Message Header by 1, AND;
o if present, increment <msg-hop-count> in the
Message Header by 1.
3. The message is transmitted over all OLSRv2
interfaces, as described in Section 13.
15. HELLO Messages
The HELLO message Message Type is owned by [RFC6130], and thus HELLO
messages are generated, transmitted, received and processed by
[RFC6130]. This protocol, as permitted by [RFC6130], also uses HELLO
messages, including adding to HELLO message generation, and #
implementing additional processing based on received HELLO messages.
HELLO messages are not forwarded by [RFC6130] or this specification.
Clausen, et al. Expires January 27, 2012 [Page 45]
Internet-Draft OLSRv2 July 2011
15.1. HELLO Message Generation
An HELLO message is generated as defined in [RFC6130], extended by
the following elements being added to the HELLO message by this
specification before the HELLO message is sent over an OLSRv2
interface:
o A message originator address, recording this router's originator
address. This MUST use a <msg-orig-addr> element, unless:
* The message specifies only a single local interface address
(i.e., contains only one address object that is associated with
an Address Block TLV with Type = LOCAL_IF, and which has no
prefix length, or a maximum prefix length) which will then be
interpreted as the message originator address, OR;
* The message does not include any local interface network
addresses (i.e., has no address objects associated with an
Address Block TLV with Type = LOCAL_IF), as permitted by the
specification in [RFC6130] when the router that generated the
HELLO message has only one interface address and will use that
as the sending address of the IP datagram in which the HELLO
message is contained. In this case that address will be
interpreted as the message originator address.
o A Message TLV with Type := MPR_WILLING and Value := WILLINGNESS
MUST be included, unless WILLINGNESS = WILL_DEFAULT (in which case
it MAY be included).
o The following cases associate Address Block TLVs with one or more
addresses from a Link Tuple or a Neighbor Tuple if these are
included in the HELLO message. In each case the TLV MUST be
associated with at least copy of one address from the relevant
Tuple, the TLV MAY be associated with more such addresses
(including a copy of that address object, possibly not itself
associated with any other indicated TLVs, in the same or a
different Address Block). These additional TLVs MUST NOT be
associated with any other addresses in a HELLO message that will
be processed by [RFC6130].
* For each Link Tuple for which L_in_metric != UNKNOWN_METRIC,
and for which one or more addresses in its
L_neighbor_iface_addr_list are included as address objects with
an associated Address Block TLV with Type = LINK_STATUS and
Value = HEARD or Value = SYMMETRIC, at least one of these
addresses MUST be associated with an Address Block TLV with
Type := LINK_METRIC indicating an incoming link metric with
value L_in_metric, unless this equals DEFAULT_METRIC.
Clausen, et al. Expires January 27, 2012 [Page 46]
Internet-Draft OLSRv2 July 2011
* For each Link Tuple for which L_out_metric != UNKNOWN_METRIC,
and for which one or more addresses in its
L_neighbor_iface_addr_list are included as address objects with
an associated Address Block TLV with Type = LINK_STATUS and
Value = SYMMETRIC, at least one of these addresses MUST be
associated with an Address Block TLV with Type := LINK_METRIC
indicating an outgoing link metric with value L_out_metric,
unless this equals DEFAULT_METRIC.
* For each Neighbor Tuple for which N_symmetric = true, and for
which one or more addresses in its N_neighbor_addr_list are
included as address objects with an associated Address Block
TLV with Type = LINK_STATUS and Value = SYMMETRIC, at least one
of these addresses MUST be associated with an Address Block TLV
with Type := LINK_METRIC indicating an incoming neighbor metric
with value N_in_metric, unless this equals DEFAULT_METRIC.
* For each Neighbor Tuple for which N_symmetric = true, and for
which one or more addresses in its N_neighbor_addr_list are
included as address objects with an associated Address Block
TLV with Type = LINK_STATUS and Value = SYMMETRIC, at least one
of these addresses MUST be associated with an Address Block TLV
with Type := LINK_METRIC indicating an outcoming neighbor
metric with value N_out_metric, unless this equals
DEFAULT_METRIC.
* For each Neighbor Tuple with N_flooding_mpr = true, and for
which one or more network addresses in its N_neighbor_addr_list
are included as address objects in the HELLO message with an
associated Address Block TLV with Type = LINK_STATUS and Value
= SYMMETRIC, at least one of these addresses MUST be associated
with an Address Block TLV with Type := MPR and Value := 0 or
Value := 1.
* For each Neighbor Tuple with N_routing_mpr = true, and for
which one or more network addresses in its N_neighbor_addr_list
are included as address objects in the HELLO message with an
associated Address Block TLV with Type = LINK_STATUS and Value
= SYMMETRIC, at least one of these addresses MUST be associated
with an Address Block TLV with Type := MPR and Value := 0 or
Value := 2.
15.2. HELLO Message Transmission
HELLO messages are scheduled and transmitted by [RFC6130]. This
protocol MAY require that an additional HELLO message is sent when
the router's set of MPRs changes, in addition to the cases specified
in [RFC6130], and subject to the same constraints.
Clausen, et al. Expires January 27, 2012 [Page 47]
Internet-Draft OLSRv2 July 2011
15.3. HELLO Message Processing
When received on an OLSRv2 interface, HELLO messages are made
available to this protocol in two ways, both as permitted by
[RFC6130]:
o Such received HELLO messages MUST be made available to this
protocol on reception, which allows them to be discarded before
being processed by [RFC6130], for example if the information added
to the HELLO message by this protocol is inconsistent.
o Such received HELLO messages MUST be made available to OLSRv2
after [RFC6130] has completed its processing thereof, unless
discarded as malformed by [RFC6130], for processing by this
protocol.
15.3.1. HELLO Message Discarding
In addition to the reasons specified in [RFC6130] for discarding a
HELLO message on reception, a HELLO message MUST be discarded before
processing by [RFC6130] or this specification if it:
o Has more than one Message TLV with Type = MPR_WILLING.
o Has a message originator address, or a network address
corresponding to an address object associated with an Address
Block TLV with Type = LOCAL_IF, that is partially owned by this
router. (Some of these cases are already excluded by [RFC6130].)
o Includes any address object associated with an Address Block TLV
with Type = LINK_STATUS or Type = OTHER_NEIGHB that overlaps the
message's originator address.
o Contains any address that will be processed by [RFC6130] that is
associated, using the same or different address objects, with two
different values of link metric with the same kind and direction
using a TLV with Type = LINK_METRIC and Type Extension =
LINK_METRIC_TYPE. This also applies to different addresses that
are both of the OLSRv2 interface on which the HELLO message was
received.
o Contains any address object associated with an Address Block TLV
with Type = MPR that is not also associated with an Address Block
TLV with Type = LINK_STATUS and Value = SYMMETRIC (including using
a different copy of that address object, in the same or a
different Address Block).
Clausen, et al. Expires January 27, 2012 [Page 48]
Internet-Draft OLSRv2 July 2011
15.3.2. HELLO Message Usage
HELLO messages are first processed as specified in [RFC6130]. That
processing includes identifying (or creating) a Neighbor Tuple
corresponding to the originator of the HELLO message (the "current
Neighbor Tuple"). After this, the following processing MUST also be
performed:
1. If the HELLO message has a well-defined message originator
address, i.e., has an <msg-orig-addr> element or has zero or one
network addresses associated with a TLV with Type = LOCAL_IF:
1. Remove any other Neighbor Tuple with N_orig_addr = message
originator address, taking any consequent action (including
removing one or more Link Tuples) as specified in [RFC6130].
2. The current Link Tuple is then updated according to:
1. Update L_in_metric and L_out_metric as described in
Section 15.3.2.1;
2. Update L_mpr_selector as described in Section 15.3.2.3.
3. The current Neighbor Tuple is then updated according to:
1. N_orig_addr := message originator address;
2. Update N_in_metric and N_out_metric as described in
Section 15.3.2.1;
3. Update N_will_flooding and N_will_routing as described in
Section 15.3.2.2;
4. Update N_mpr_selector as described in Section 15.3.2.3.
2. If there are any changes to the router's Information Bases, then
perform the processing defined in Section 17.
15.3.2.1. Updating Metrics
For each address in a received HELLO message with an associated TLV
with Type = LINK_STATUS and Value = HEARD or Value = SYMMETRIC, an
incoming (to the message originator) link metric value is defined
either using an associated TLV with Type = LINK_METRIC and Type
Extension = LINK_METRIC_TYPE that indicates the appropriate kind
(link) and direction (incoming) of metric, or as the value
DEFAULT_METRIC.
Clausen, et al. Expires January 27, 2012 [Page 49]
Internet-Draft OLSRv2 July 2011
For each address in a received HELLO message with an associated TLV
with Type = LINK_STATUS and Value = SYMMETRIC, an outgoing (to the
message originator) link metric value is defined either using an
associated TLV with Type = LINK_METRIC and Type Extension =
LINK_METRIC_TYPE that indicates the appropriate kind (link) and
direction (outgoing) of metric, or as the value DEFAULT_METRIC.
For each address in a received HELLO message with an associated TLV
with Type = LINK_STATUS or Type = OTHER_NEIGHB and Value = SYMMETRIC,
an incoming (to the message originator) neighbor metric value is
defined either using an associated TLV with Type = LINK_METRIC and
Type Extension = LINK_METRIC_TYPE that indicates the appropriate kind
(neighbor) and direction (incoming) of metric, or as the value
DEFAULT_METRIC.
For each address in a received HELLO message with an associated TLV
with Type = LINK_STATUS or Type = OTHER_NEIGHB and Value = SYMMETRIC,
an outgoing (to the message originator) neighbor metric value is
defined either using an associated TLV with Type = LINK_METRIC and
Type Extension = LINK_METRIC_TYPE that indicates the appropriate kind
(neighbor) and direction (outgoing) of metric, or as the value
DEFAULT_METRIC.
The link metric elements L_in_metric and L_out_metric in a Link Tuple
are updated according to the following:
o For any Link Tuple, L_in_metric MAY be set to any representable
value, by a process outside this specification, at any time.
L_in_metric MUST be so set whenever L_status becomes equal to
HEARD or SYMMETRIC (if no other value is available then the value
MAXIMUM_METRIC SHOULD be used). This MAY use information based on
the receipt of a packet including a HELLO message that causes the
creation or updating of that Link Tuple.
o When, as specified in [RFC6130], a Link Tuple is updated (possibly
immediately after being created) due to the receipt of a HELLO
message, if L_status = SYMMETRIC, then L_out_metric is set equal
to the incoming link metric for any included address of the
interface on which the HELLO message was received, ignoring any
values equal to DEFAULT_METRIC unless there are only such values.
(Note that the rules for discarding HELLO messages in
Section 15.3.1 make this value unambiguous.)
The neighbor metric elements N_in_metric and N_out_metric in a
Neighbor Tuple are updated according to Section 17.3.
The metric elements N2_in_metric and N2_out_metric in any 2-Hop Tuple
updated as defined in [RFC6130] are updated to equal the incoming
Clausen, et al. Expires January 27, 2012 [Page 50]
Internet-Draft OLSRv2 July 2011
neighbor metric and outgoing neighbor metric, respectively,
associated with the corresponsing N2_2hop_addr.
15.3.2.2. Updating Willingness
N_will_flooding and N_will_routing in the current Neighbor Tuple are
updated as follows:
1. If the HELLO message contains a Message TLV with Type =
MPR_WILLING then N_will_flooding := bits 0-3 of the value of that
TLV, and N_will_routing := bits 4-7 of the value of that TLV
(each in the range 0 to 15).
2. Otherwise, N_will_flooding := WILL_DEFAULT, and N_will_routing :=
WILL_DEFAULT.
15.3.2.3. Updating MPR Selector Status
L_mpr_selector is updated as follows:
1. If a router finds an address object representing any of its local
interface network addresses (i.e., those contained in the
I_local_iface_addr_list of an OLSRv2 interface) with an
associated Address Block TLV with Type = MPR and Value = 0 or
Value = 1 in the HELLO message (indicating that the originating
router has selected the receiving router as a flooding MPR) then,
for the current Link Tuple:
* L_mpr_selector := true
2. Otherwise (i.e., if no such address object and Address Block TLV
was found) if a router finds an address object representing any
of its local interface network addresses (i.e., those contained
in the I_local_iface_addr_list of an OLSRv2 interface) with an
associated Address Block TLV with Type = LINK_STATUS and Value =
SYMMETRIC in the HELLO message, then for the current Link Tuple:
* L_mpr_selector := false
N_mpr_selector is updated as follows:
1. If a router finds an address object representing any of its local
interface network addresses (i.e., those contained in the
I_local_iface_addr_list of an OLSRv2 interface) with an
associated Address Block TLV with Type = MPR and Value = 0 or
Value = 2 in the HELLO message (indicating that the originating
router has selected the receiving router as a routing MPR) then,
for the current Neighbor Tuple:
Clausen, et al. Expires January 27, 2012 [Page 51]
Internet-Draft OLSRv2 July 2011
* N_mpr_selector := true
* N_advertised := true
2. Otherwise (i.e., if no such address object and Address Block TLV
was found) if a router finds an address object representing any
of its local interface network addresses (i.e., those contained
in the I_local_iface_addr_list of an OLSRv2 interface) with an
associated Address Block TLV with Type = LINK_STATUS and Value =
SYMMETRIC in the HELLO message, then for the current Neighbor
Tuple:
* N_mpr_selector := false
* The router MAY also set N_advertised := false
16. TC Messages
This protocol defines, and hence owns, the TC message type (see
Section 24). Thus, as specified in [RFC5444], this protocol
generates and transmits all TC messages, receives all TC messages and
is responsible for determining whether and how each TC message is to
be processed (updating the Topology Information Base) and/or
forwarded, according to this specification.
16.1. TC Message Generation
A TC message is a message as defined in [RFC5444]. A generated TC
message MUST contain the following elements as defined in [RFC5444]:
o A message originator address, recording this router's originator
address. This MUST use a <msg-orig-addr> element.
o <msg-seq-num> element containing the message sequence number.
o A <msg-hop-limit> element, containing TC_HOP_LIMIT. A router MAY
use the same or different values of TC_HOP_LIMIT in its TC
messages, see Section 5.4.7.
o A <msg-hop-count> element, containing zero, if the message
contains a TLV with either Type = VALIDITY_TIME or Type =
INTERVAL_TIME (as specified in [RFC5497]) indicating more than one
time value according to distance. A TC message MAY contain such a
<msg-hop-count> element even if it does not need to.
o A single Message TLV with Type := CONT_SEQ_NUM and Value := ANSN
from the Neighbor Information Base. If the TC message is complete
then this Message TLV MUST have Type Extension := COMPLETE,
Clausen, et al. Expires January 27, 2012 [Page 52]
Internet-Draft OLSRv2 July 2011
otherwise it MUST have Type Extension := INCOMPLETE. (Exception:
a TC message MAY omit such a Message TLV if the TC message does
not include any address objects with an associated Address Block
TLV with Type = NBR_ADDR_TYPE or Type = GATEWAY.)
o A single Message TLV with Type := VALIDITY_TIME, as specified in
[RFC5497]. If all TC messages are sent with the same hop limit
then this TLV MUST have a value encoding the period T_HOLD_TIME.
If TC messages are sent with different hop limits (more than one
value of TC_HOP_LIMIT) then this TLV MUST specify times that vary
with the number of hops distance appropriate to the chosen pattern
of TC message hop limits, as specified in [RFC5497]; these times
SHOULD be appropriate multiples of T_HOLD_TIME. The options
included in [RFC5497] for representing zero and infinite times
MUST NOT be used.
o If the TC message is complete, all network addresses which are the
N_orig_addr of a Neighbor Tuple with N_advertised = true, MUST be
represented by address objects in one or more Address Blocks. If
the TC message is incomplete then any such address objects MAY be
included. At least one copy of each such address object that is
included MUST be associated with an Address Block TLV with Type :=
NBR_ADDR_TYPE, and Value := ORIGINATOR, or with Value :=
ROUTABLE_ORIG if that address object is also to be associated with
Value = ROUTABLE.
o If the TC message is complete, all routable addresses which are in
the N_neighbor_addr_list of a Neighbor Tuple with N_advertised =
true MUST be represented by address objects in one or more Address
Blocks. If the TC message is incomplete then any such address
objects MAY be included. At least one copy of each such address
object MUST be associated with an Address Block TLV with Type =
NBR_ADDR_TYPE, and Value = ROUTABLE, or with Value = ROUTABLE_ORIG
if also to be associated with Value = ORIGINATOR. At least one
copy of each such address object MUST be associated with an
Address Block TLV with Type = LINK_METRIC and Type Extension =
LINK_METRIC_TYPE indicating an outgoing neighbor metric with value
equal to the corresponding N_out_metric, unless that value is
DEFAULT_METRIC.
o If the TC message is complete, all network addresses which are the
AL_net_addr of a Local Attached Network Tuple MUST be represented
by address objects in one or more Address Blocks. If the TC
message is incomplete then any such address objects MAY be
included. At least one copy of each such address object MUST be
associated with an Address Block TLV with Type := GATEWAY, and
Value := AN_dist. At least one copy of each such address object
MUST be associated with an Address Block TLV with Type =
Clausen, et al. Expires January 27, 2012 [Page 53]
Internet-Draft OLSRv2 July 2011
LINK_METRIC and Type Extension = LINK_METRIC_TYPE indicating an
outgoing neighbor metric equal to the corresponding AL_metric,
unless that value is DEFAULT_METRIC.
A TC message MAY contain:
o A single Message TLV with Type := INTERVAL_TIME, as specified in
[RFC5497]. If all TC messages are sent with the same hop limit
then this TLV MUST have a value encoding the period TC_INTERVAL.
If TC messages are sent with different hop limits, then this TLV
MUST specify times that vary with the number of hops distance
appropriate to the chosen pattern of TC message hop limits, as
specified in [RFC5497]; these times SHOULD be appropriate
multiples of TC_INTERVAL. The options included in [RFC5497] for
representing zero and infinite times MUST NOT be used.
16.2. TC Message Transmission
A router with one or more OLSRv2 interfaces, and with any Neighbor
Tuples with N_advertised = true, or with a non-empty Local Attached
Network Set MUST generate TC messages. A router which does not have
such information to advertise SHOULD also generate "empty" TC
messages for a period A_HOLD_TIME after it last generated a non-empty
TC message.
Complete TC messages are generated and transmitted periodically on
all OLSRv2 interfaces, with a default interval between two
consecutive TC transmissions by the same router of TC_INTERVAL.
TC messages MAY be generated in response to a change in the
information which they are to advertise, indicated by a change in the
ANSN in the Neighbor Information Base. In this case a router MAY
send a complete TC message, and if so MAY re-start its TC message
schedule. Alternatively a router MAY send an incomplete TC message
with at least the newly advertised network addresses (i.e., not
previously, but now, an N_orig_addr or in an N_neighbor_addr_list in
a Neighbor Tuple with N_advertised = true, or an AL_net_addr) in its
Address Blocks, with associated Address Block TLV(s). Note that a
router cannot report removal of advertised content using an
incomplete TC message.
When sending a TC message in response to a change of advertised
network addresses, a router MUST respect a minimum interval of
TC_MIN_INTERVAL between generated TC messages. Sending an incomplete
TC message MUST NOT cause the interval between complete TC messages
to be increased, and thus a router MUST NOT send an incomplete TC
message if within TC_MIN_INTERVAL of the next scheduled complete TC
message.
Clausen, et al. Expires January 27, 2012 [Page 54]
Internet-Draft OLSRv2 July 2011
The generation of TC messages, whether scheduled or triggered by a
change of contents, MAY be jittered as described in [RFC5148]. The
values of MAXJITTER used SHOULD be:
o TP_MAXJITTER for periodic TC message generation;
o TT_MAXJITTER for responsive TC message generation.
16.3. TC Message Processing
On receiving a TC message, the receiving router MUST then follow the
processing and forwarding procedure, defined in Section 14.
If the message is considered for processing (Section 14.2), then a
router MUST first check if the message is invalid for processing by
this router, as defined in Section 16.3.1. A router MAY make a
similar check before considering a message for forwarding, it MUST
make those aspects of the check that apply to elements in the Message
Header.
If the TC message is not invalid, then the TC message type specific
processing, described in Section 16.3.2 MUST be applied. This will
update its appropriate Interface Information Base and its Router
Information Base. Following this, if there are any changes in these
Information Bases, then the processing in Section 17 MUST be
performed.
16.3.1. Invalid Message
A received TC message is invalid for processing by this router if the
message:
o Has an address length specified in the Message Header that is not
equal to the length of the addresses used by this router.
o Does not include a message originator address and a message
sequence number.
o Does not include a hop count, and contains a multi-value TLV with
Type = VALIDITY_TIME or Type = INTERVAL_TIME, as defined in
[RFC5497].
o Does not have exactly one Message TLV with Type = VALIDITY_TIME.
o Has more than one Message TLV with Type = INTERVAL_TIME.
o Does not have a Message TLV with Type = CONT_SEQ_NUM and Type
Extension = COMPLETE or Type Extension = INCOMPLETE, and contains
Clausen, et al. Expires January 27, 2012 [Page 55]
Internet-Draft OLSRv2 July 2011
at least one address object associated with an Address Block TLV
with Type = NBR_ADDR_TYPE or Type = GATEWAY.
o Has more than one Message TLV with Type = CONT_SEQ_NUM and Type
Extension = COMPLETE or Type Extension = INCOMPLETE.
o Has a message originator address that is partially owned by this
router.
o Includes any address object with a prefix length which is not
maximal (equal to the address length, in bits), associated with an
Address Block TLV with Type = NBR_ADDR_TYPE and Value = ORIGINATOR
or Value = ROUTABLE_ORIG.
o Includes any address object that represents a non-routable
address, associated with an Address Block TLV with Type =
NBR_ADDR_TYPE and Value = ROUTABLE or Value = ROUTABLE_ORIG.
o Includes any address object associated with an Address Block TLV
with Type = NBR_ADDR_TYPE or Type = GATEWAY that also represents
the message's originator address.
o Includes any address object (including different copies of an
address object, in the same or different Address Blocks) that is
associated with an Address Block TLV with Type = NBR_ADDR_TYPE or
Type = GATEWAY, that is also associated with more than one
outgoing neighbor metric using a TLV with Type = LINK_METRIC and
Type Extension = LINK_METRIC_TYPE.
o Associates any address object (including different copies of an
address object, in the same or different Address Blocks) with more
than one single hop count value using one or more Address Block
TLV(s) with Type = GATEWAY.
o Associates any address object (including different copies of an
address object, in the same or different Address Blocks) with
Address Block TLVs with Type = NBR_ADDR_TYPE and Type = GATEWAY.
A router MAY recognize additional reasons for identifying that a
message is invalid. An invalid message MUST be silently discarded,
without updating the router's Information Bases.
16.3.2. TC Message Processing Definitions
When, according to Section 14.2, a TC message is to be "processed
according to its type", this means that:
Clausen, et al. Expires January 27, 2012 [Page 56]
Internet-Draft OLSRv2 July 2011
o If the TC message contains a Message TLV with Type = CONT_SEQ_NUM
and Type Extension = COMPLETE, then processing according to
Section 16.3.3 and then according to Section 16.3.4 is carried
out.
o If the TC message contains a Message TLV with Type = CONT_SEQ_NUM
and Type Extension = INCOMPLETE, then only processing according to
Section 16.3.3 is carried out.
For the purposes of this section:
o "validity time" is calculated from a VALIDITY_TIME Message TLV in
the TC message according to the specification in [RFC5497]. All
information in the TC message has the same validity time.
o "received ANSN" is defined as being the value of a Message TLV
with Type = CONT_SEQ_NUM.
o "associated metric value" is defined for any address in the TC
message as being either the outgoing neighbor metric value
indicated by a TLV with Type = LINK_METRIC and Type Extemsion =
LINK_METRIC_TYPE that is associated with any address object in the
TC message that is equal to that address, or as DEFAULT_METRIC
otherwise. (Note that the rules in Section 16.3.1 make this
definition unambiguous.)
o Comparisons of sequence numbers are carried out as specified in
Section 21.
16.3.3. Initial TC Message Processing
The TC message is processed as follows:
1. The Advertising Remote Router Set is updated according to
Section 16.3.3.1. If the TC message is indicated as discarded in
that processing then the following steps are not carried out.
2. The Router Topology Set is updated according to Section 16.3.3.2.
3. The Routable Address Topology Set is updated according to
Section 16.3.3.3.
4. The Attached Network Set is updated according to
Section 16.3.3.4.
Clausen, et al. Expires January 27, 2012 [Page 57]
Internet-Draft OLSRv2 July 2011
16.3.3.1. Populating the Advertising Remote Router Set
The router MUST update its Advertising Remote Router Set as follows:
1. If there is an Advertising Remote Router Tuple with:
* AR_orig_addr = message originator address, AND;
* AR_seq_number > received ANSN,
then the TC message MUST be discarded.
2. Otherwise:
1. If there is no Advertising Remote Router Tuple such that:
+ AR_orig_addr = message originator address;
then create an Advertising Remote Router Tuple with:
+ AR_orig_addr := message originator address.
2. This Advertising Remote Router Tuple (existing or new) is
then modified as follows:
+ AR_seq_number := received ANSN;
+ AR_time := current time + validity time.
16.3.3.2. Populating the Router Topology Set
The router MUST update its Router Topology Set as follows:
1. For each address (henceforth advertised address) corresponding to
one or more address objects with an associated Address Block TLV
with Type = NBR_ADDR_TYPE and Value = ORIGINATOR or Value =
ROUTABLE_ORIG, and that is not partially owned by this router,
perform the following processing:
1. If there is no Router Topology Tuple such that:
+ TR_from_orig_addr = message originator address, AND;
+ TR_to_orig_addr = advertised address,
then create a new Router Topology Tuple with:
Clausen, et al. Expires January 27, 2012 [Page 58]
Internet-Draft OLSRv2 July 2011
+ TR_from_orig_addr := message originator address;
+ TR_to_orig_addr := advertised address.
2. This Router Topology Tuple (existing or new) is then modified
as follows:
+ TR_seq_number := received ANSN;
+ TR_metric := associated link metric;
+ TR_time := current time + validity time.
16.3.3.3. Populating the Routable Address Topology Set
The router MUST update its Routable Address Topology Set as follows:
1. For each network address (henceforth advertised address)
corresponding to one or more address objects with an associated
Address Block TLV with Type = NBR_ADDR_TYPE and Value = ROUTABLE
or Value = ROUTABLE_ORIG, and that is not partially owned by this
router, perform the following processing:
1. If there is no Routable Address Topology Tuple such that:
+ TA_from_orig_addr = message originator address, AND;
+ TA_dest_addr = advertised address,
then create a new Routable Address Topology Tuple with:
+ TA_from_orig_addr := message originator address;
+ TA_dest_addr := advertised address.
2. This Routable Address Topology Tuple (existing or new) is
then modified as follows:
+ TA_seq_number := received ANSN;
+ TA_metric := associated link metric;
+ TA_time := current time + validity time.
Clausen, et al. Expires January 27, 2012 [Page 59]
Internet-Draft OLSRv2 July 2011
16.3.3.4. Populating the Attached Network Set
The router MUST update its Attached Network Set as follows:
1. For each network address (henceforth attached address)
corresponding to one or more address objects with an associated
Address Block TLV with Type = GATEWAY, and that is not fully
owned by this router, perform the following processing:
1. If there is no Attached Network Tuple such that:
+ AN_net_addr = attached address, AND;
+ AN_orig_addr = message originator address,
then create a new Attached Network Tuple with:
+ AN_net_addr := attached address;
+ AN_orig_addr := message originator address.
2. This Attached Network Tuple (existing or new) is then
modified as follows:
+ AN_seq_number := received ANSN;
+ AN_dist := the Value of the associated GATEWAY TLV;
+ AN_metric := associated link metric;
+ AN_time := current time + validity time.
16.3.4. Completing TC Message Processing
The TC message is processed as follows:
1. The Router Topology Set is updated according to Section 16.3.4.1.
2. The Routable Address Topology Set is updated according to
Section 16.3.4.2.
3. The Attached Network Set is updated according to
Section 16.3.4.3.
Clausen, et al. Expires January 27, 2012 [Page 60]
Internet-Draft OLSRv2 July 2011
16.3.4.1. Purging the Router Topology Set
The Router Topology Set MUST be updated as follows:
1. Any Router Topology Tuples with:
* TR_from_orig_addr = message originator address, AND;
* TR_seq_number < received ANSN,
MUST be removed.
16.3.4.2. Purging the Routable Address Topology Set
The Routable Address Topology Set MUST be updated as follows:
1. Any Routable Address Topology Tuples with:
* TA_from_orig_addr = message originator address, AND;
* TA_seq_number < received ANSN,
MUST be removed.
16.3.4.3. Purging the Attached Network Set
The Attached Network Set MUST be updated as follows:
1. Any Attached Network Tuples with:
* AN_orig_addr = message originator address, AND;
* AN_seq_number < received ANSN,
MUST be removed.
17. Information Base Changes
The changes described in the following sections MUST be carried out
when any Information Base changes as indicated.
17.1. Originator Address Changes
If the router changes originator address, then:
1. If there is no Originator Tuple with:
Clausen, et al. Expires January 27, 2012 [Page 61]
Internet-Draft OLSRv2 July 2011
* O_orig_addr = old originator address
then create an Originator Tuple with:
* O_orig_addr := old originator address
The Originator Tuple (existing or new) with:
* O_orig_addr = new originator address
is then modified as follows:
* O_time := current time + O_HOLD_TIME
17.2. Link State Changes
The consistency of a Link Tuple MUST be maintained accoprding to the
following rules, in addition to those in [RFC6130]:
o If L_status = HEARD or L_status = SYMMETRIC, then L_in_metric MUST
be set (by a process outside this specification).
o If L_status != SYMMETRIC, then set L_mpr_selector := false.
o If L_out_metric = UNKNOWN_METRIC, then L_status MUST NOT equal
SYMMETRIC; set L_SYM_time := expired if this would otherwise be
the case.
17.3. Neighbor State Changes
The consistency of a Neighbor Tuple MUST be maintained according to
the following rules, in addition to those in [RFC6130]:
1. If N_symmetric = true, then N_in_metric MUST equal the minimum
value of all L_in_metric of corresponding Link Tuples with
L_status = SYMMETRIC.
2. If N_symmetric = true, then N_out_metric MUST equal the minimum
value of all L_out_metric of corresponding Link Tuples with
L_status = SYMMETRIC.
3. If N_symmetric = false, then N_flooding_mpr, N_routing_mpr,
N_mpr_selector and N_advertised MUST all be equal to false.
4. If N_mpr_selector = true, then N_advertised MUST be equal to
true.
Clausen, et al. Expires January 27, 2012 [Page 62]
Internet-Draft OLSRv2 July 2011
5. If N_symmetric = true and N_mpr_selector = false, then a router
MAY select N_advertised = true or N_advertised = false. The more
neighbors that are advertised, the larger TC messages become, but
the more redundancy is available for routing. A router SHOULD
consider the nature of its network in making such a decision, and
SHOULD avoid unnecessary changes in advertising status, which may
result both in additional TC messages having to be sent by its
neighbors, and in unnecessary changes to routing, which will have
similar effects to other forms of topology changes in the MANET.
17.4. Advertised Neighbor Changes
The router MUST increment the ANSN in the Neighbor Information Base
whenever:
1. Any Neighbor Tuple changes its N_advertised value, or any
Neighbor Tuple with N_advertised = true is removed.
2. Any Neighbor Tuple with N_advertised = true changes its
N_orig_addr, or has any routable address is added to or removed
from N_neighbor_addr_list.
3. Any Neighbor Tuple with N_advertised = true has N_out_metric
changed.
4. There is any change to the Local Attached Network Set.
17.5. Advertising Remote Router Tuple Expires
The Router Topology Set, the Routable Address Topology Set and the
Attached Network Set MUST be changed when an Advertising Remote
Router Tuple expires (AR_time is reached). The following changes are
required before the Advertising Remote Router Tuple is removed:
1. All Router Topology Tuples with:
* TR_from_orig_addr = AR_orig_addr of the Advertising Remote
Router Tuple
are removed.
2. All Routable Address Topology Tuples with:
* TA_from_orig_addr = AR_orig_addr of the Advertising Remote
Router Tuple
are removed.
Clausen, et al. Expires January 27, 2012 [Page 63]
Internet-Draft OLSRv2 July 2011
3. All Attached Network Tuples with:
* AN_orig_addr = AR_orig_addr of the Advertising Remote Router
Tuple
are removed.
17.6. Neighborhood Changes and MPR Updates
The sets of symmetric 1-hop neighbors selected as flooding MPRs and
routing MPRs MUST satisfy the conditions defined in Section 18. To
ensure this:
1. The set of flooding MPRs of a router MUST be recalculated if:
* a Link Tuple is added with L_status = SYMMETRIC, OR;
* a Link Tuple with L_status = SYMMETRIC is removed, OR;
* a Link Tuple with L_status = SYMMETRIC changes to having
L_status = HEARD or L_status = LOST, OR;
* a Link Tuple with L_status = HEARD or L_status = LOST changes
to having L_status = SYMMETRIC, OR;
* a 2-Hop Tuple is added or removed, OR;
* the N_will_flooding of a Neighbor Tuple with N_symmetric =
true changes from WILL_NEVER to any other value, OR;
* the N_will_flooding of a Neighbor Tuple with N_flooding_mpr =
true changes to WILL_NEVER from any other value, OR;
* the N_will_flooding of a Neighbor Tuple with N_symmetric =
true and N_flooding_mpr = false changes to WILL_ALWAYS from
any other value.
2. Otherwise, the set of flooding MPRs of a router MAY be
recalculated if the N_will_flooding of a Neighbor Tuple with
N_symmetric = true changes in any other way; it SHOULD be
recalculated if N_flooding_mpr = false and this is an increase in
N_will_flooding or if N_flooding_mpr = true and this is a
decrease in N_will_flooding.
3. The set of routing MPRs of a router MUST be recalculated if:
* a Link Tuple is added with L_status = SYMMETRIC, OR;
Clausen, et al. Expires January 27, 2012 [Page 64]
Internet-Draft OLSRv2 July 2011
* a Link Tuple with L_status = SYMMETRIC is removed, OR;
* a Link Tuple with L_status = SYMMETRIC changes to having
L_status = HEARD or L_status = LOST, OR;
* a Link Tuple with L_status = HEARD or L_status = LOST changes
to having L_status = SYMMETRIC, OR;
* a 2-Hop Tuple is added or removed, OR;
* the N_will_routing of a Neighbor Tuple with N_symmetric = true
changes from WILL_NEVER to any other value, OR;
* the N_will_routing of a Neighbor Tuple with N_routing mpr =
true changes to WILL_NEVER from any other value, OR;
* the N_will_routing of a Neighbor Tuple with N_symmetric = true
and N_routing_mpr = false changes to WILL_ALWAYS from any
other value.
4. Otherwise, the set of routing MPRs of a router MAY be
recalculated if the N_will_routing of a Neighbor Tuple with
N_symmetric = true changes in any other way; it SHOULD be
recalculated if N_routing_mpr = false and this is an increase in
N_will_routing or if N_routing_mpr = true and this is a decrease
in N_will_routing.
If either set of MPRs of a router is recalculated, this MUST be as
described in Section 18. Before that calculation, N_flooding_mpr or
N_routing_mpr (as appropriate) of all Neighbor Tuples is set false
(although its previous value MAY be used by an algorithm that
minimizes changes to the set of MPRs). After that calculation the
N_flooding_mpr or N_routing_mpr (as appropriate) of all Neighbor
Tuples representing symmetric 1-hop neighbors that are chosen as
MPRs, are set true.
17.7. Routing Set Updates
The Routing Set MUST be updated, as described in Section 19 when
changes in the Local Information Base, the Neighborhood Information
Base or the Topology Information Base indicate a change (including of
any potentially used link metric values, all outgoing) of the known
symmetric links and/or attached networks in the MANET, hence changing
the Topology Graph. It is sufficient to consider only changes which
affect at least one of:
o The Local Interface Set, if the change removes any network address
in an I_local_iface_addr_list. In this case, unless the OLSRv2
Clausen, et al. Expires January 27, 2012 [Page 65]
Internet-Draft OLSRv2 July 2011
interface is removed, it may not be necessary to do more than
replace such network addresses, if used, by an alternative network
address from the same I_local_iface_addr_list.
o The Local Attached Set, if the change removes any AL_net_addr
which is also an AN_net_addr. In this case it may not be
necessary to do more than add Routing Tuples with R_dest_addr
equal to that AN_net_addr.
o The Link Set of any OLSRv2 interface, considering only Link Tuples
which have, or just had, L_status = SYMMETRIC (including removal
of such Link Tuples).
o The Neighbor Set of the router, considering only Neighbor Tuples
that have, or just had, N_symmetric = true, and do not have
N_orig_addr = unknown.
o The 2-Hop Set of any OLSRv2 interface, if used in the creation of
the Routing Set.
o The Router Topology Set of the router.
o The Routable Address Topology Set of the router.
o The Attached Network Set of the router.
18. Selecting MPRs
Note: This section has not yet been updated to use link metrics and
separate sets of flooding and routing MPRs.
Each router MUST select, from among its willing symmetric 1-hop
neighbors, a subset of these routers as MPRs. Only MPRs forward
control messages flooded through the MANET, thus effecting a flooding
reduction, an optimization of the classical flooding mechanism, known
as MPR flooding. MPRs MAY also be used to effect a topology
reduction in the MANET. Consequently, while it is not essential that
the set of MPRs is minimal, keeping the number of MPRs small ensures
that the overhead is kept at a minimum.
A router MUST select MPRs for each of its OLSRv2 interfaces, but then
forms the union of those sets as its single set of MPRs. This union
MUST include all symmetric 1-hop neighbors with willingness
WILL_ALWAYS. Only this overall set of MPRs is relevant, the recorded
and used MPR relationship is one of routers, not interfaces. Routers
MAY select their MPRs by any process which satisfies the conditions
which follow. Routers can freely interoperate whether they use the
same or different MPR selection algorithms.
Clausen, et al. Expires January 27, 2012 [Page 66]
Internet-Draft OLSRv2 July 2011
For each OLSRv2 interface a router MUST select a set of MPRs. This
set MUST have the properties that:
o All of the selected MPRs are willing symmetric 1-hop neighbors,
AND;
o If the selecting router sends a message on that OLSRv2 interface,
and that message is successfully forwarded by all of the selected
MPRs for that interface, then all symmetric strict 2-hop neighbors
of the selecting router through that OLSRv2 interface will receive
that message over a symmetric link.
When a router selects its set of MPRs it MAY consider any other
characteristics of its neighbors that it is aware of. In particular
it SHOULD consider the willingness of the neighbor, as recorded by
the corresponding N_willingness value, preferring neighbors with
higher values of N_willingness, but MAY consider other
characteristics to have a greater significance.
Note that it is always possible to select a valid set of MPRs. The
set of all willing symmetric 1-hop neighbors of a router is a
(maximal) valid set of MPRs for that router. However a router SHOULD
NOT select a symmetric 1-hop neighbor with N_willingness !=
WILL_ALWAYS as an MPR if there are no symmetric strict 2-hop
neighbors with a symmetric link to that symmetric 1-hop neighbor.
Thus a router with no symmetric 1-hop neighbors with N_willingness =
WILL_ALWAYS and with no symmetric strict 2-hop neighbors SHOULD NOT
select any MPRs.
A router MAY select its MPRs for each OLSRv2 interface independently,
or it MAY coordinate its MPR selections across its OLSRv2 interfaces,
as long as the required condition is satisfied for each OLSRv2
interface. Each router MAY select its MPRs independently from the
MPR selection by other routers, or it MAY, for example, give
preference to routers that either are, or are not, already selected
as MPRs by other routers.
When selecting MPRs for each OLSRv2 interface independently, this MAY
be done using information from the Link Set and 2-Hop Set of that
OLSRv2 interface only, and the Neighbor Set of the router
(specifically the N_willingness elements).
The selection of MPRs is recorded in the Neighbor Set of the router,
by setting N_mpr = true for any selected MPR (on any OLSRv2
interface) and ensuring that N_mpr = false otherwise. A selected MPR
MUST be a willing symmetric 1-hop neighbor (i.e., MUST have
corresponding N_symmetric = true, and corresponding N_willingness !=
WILL_NEVER). Note that although selected per OLSRv2 interface, MPRs
Clausen, et al. Expires January 27, 2012 [Page 67]
Internet-Draft OLSRv2 July 2011
are recorded and used independent of interface, i.e., a router's set
of MPRs is the union of the sets of MPRs selected per OLSRv2
interface.
A router MUST recalculate its MPRs whenever the currently selected
set of MPRs does not still satisfy the required conditions. It MAY
recalculate its MPRs if the current set of MPRs is still valid, but
could be more efficient. Sufficient conditions to recalculate a
router's set of MPRs are given in Section 17.6.
An example algorithm that creates a set of MPRs that satisfies the
required conditions is given in Appendix A.
19. Routing Set Calculation
The Routing Set of a router is populated with Routing Tuples that
represent paths from that router to all destinations in the network.
These paths are calculated based on the Network Topology Graph, which
is constructed from information in the Information Bases, obtained
via HELLO and TC message exchange.
Changes to the Routing Set do not require any messages to be
transmitted. The state of the Routing Set SHOULD, however, be
reflected in IP's routing table by adding and removing entries from
IP's routing table as appropriate. Only appropriate Routing Tuples
(in particular only those that represent local links or paths to
routable addresses) need be reflected in IP's routing table.
19.1. Network Topology Graph
The Network Topology Graph is formed from information from the
router's Local Interface Set, Link Sets, Neighbor Set, Router
Topology Set, Routable Address Topology Set and Attached Network Set.
The Network Topology Graph MAY also use information from the router's
2-Hop Sets. The Network Topology Graph forms the router's
topological view of the network in form of a directed graph. Each
edge in that graph has a metric value. The Network Topology Graph
has a "backbone" (within which minimum total metric routes will be
constructed) containing the following edges:
o Edges X -> Y for all possible Y, and one X per Y, such that:
* Y is the N_orig_addr of a Neighbor Tuple, AND;
* N_orig_addr is not unknown;
* X is in the I_local_iface_addr_list of a Local Interface Tuple,
AND;
Clausen, et al. Expires January 27, 2012 [Page 68]
Internet-Draft OLSRv2 July 2011
* There is a Link Tuple with L_status = SYMMETRIC such that this
Neighbor Tuple and this Local Interface Tuple correspond to it.
A network address from L_neighbor_iface_addr_list will be
denoted R in this case.
It SHOULD be preferred, where possible, to select R = S and X from
the Local Interface Tuple corresponding to the Link Tuple from
which R was selected. The metrio such an edge is the
corresponding N_out_metric.
o All edges W -> U such that:
* W is the TR_from_orig_addr of a Router Topology Tuple, AND;
* U is the TR_to_orig_addr of the same Router Topology Tuple.
The metrio of such an edge is the corresponding TR_metric.
The Network Topology Graph is further "decorated" with the following
edges. If a network address S, V, Z or T equals a network address Y
or W, then the edge terminating in the network address S, V, Z or T
MUST NOT be used in any path.
o Edges X -> S for all possible S, and one X per S, such that:
* S is in the N_neighbor_addr_list of a Neighbor Tuple, AND;
* X is in the I_local_iface_addr_list of a Local Interface Tuple,
AND;
* There is a Link Tuple with L_status = SYMMETRIC such that this
Neighbor Tuple and this Local Interface Tuple correspond to it.
A network address from L_neighbor_iface_addr_list will be
denoted R in this case.
It SHOULD be preferred, where possible, to select R = S and X from
the Local Interface Tuple corresponding to the Link Tuple from
which R was selected. The metric of such an edge is the
corresponding N_out_metric.
o All edges W -> V such that:
* W is the TA_from_orig_addr of a Routable Address Topology
Tuple, AND;
* V is the TA_dest_addr of the same Routable Address Topology
Tuple.
Clausen, et al. Expires January 27, 2012 [Page 69]
Internet-Draft OLSRv2 July 2011
The metric for such an edge is the corresponding TA_metric.
o All edges W -> T such that:
* W is the AN_orig_addr of an Attached Network Tuple, AND;
* T is the AN_net_addr of the same Attached Network Tuple.
The metric for such an edge is the corresponding AN_metric.
o OPTIONALLY, all edges Y -> Z such that:
* Z is a routable address and is the N2_2hop_addr of a 2-Hop
Tuple, AND;
* Y is the N_orig_addr of the corresponding Neighbor Tuple, AND;
* This Neighbor Tuple has N_willingness not equal to WILL_NEVER.
A path terminating with such an edge SHOULD NOT be used in
preference to any other path. The metric for such an edge is the
corresponding N2_metric.
Any part of the Topology Graph which is not connected to a local
network address X is not used. Only one selection X SHOULD be made
from each I_local_iface_addr_list, and only one selection R SHOULD be
made from any L_neighbor_iface_addr_list. All edges have a hop count
of 1, except edges W -> T that have a hop count of the corresponding
value of AN_dist.
19.2. Populating the Routing Set
The Routing Set MUST contain the shortest paths for all destinations
from all local OLSRv2 interfaces using the Network Topology Graph.
This calculation MAY use any algorithm, including any means of
choosing between paths of equal total metric. (In the case of two
paths of equal total metric but differing hop counts, the path with
the lower hop count SHOULD be used.)
Using the notation of Section 19.1, initially "backbone" paths using
only edges X -> Y and W -> U need be constructed (using a minimum
distance algorithm). Then paths using only a final edge of the other
types may be added. These MUST NOT replace backbone paths with the
same destination (and paths terminating in an edge Y -> Z SHOULD NOT
replace paths with any other form of terminating edge).
Each path will correspond to a Routing Tuple. These will be of two
types. The first type will represent single edge paths, of type X ->
Clausen, et al. Expires January 27, 2012 [Page 70]
Internet-Draft OLSRv2 July 2011
S or X -> Y, by:
o R_local_iface_addr := X;
o R_next_iface_addr := R;
o R_dest_addr := S or Y;
o R_dist := 1;
o R_metric := edge metric.
where R is as defined in Section 19.1 for these types of edges.
The second type will represent a multiple edge path, which will
always have first edge of type X -> Y, and will have final edge of
type W -> U, W -> V, W -> T or Y -> Z. The Routing Tuple will be:
o R_local_iface_addr := X;
o R_next_iface_addr := Y;
o R_dest_addr := U, V, T or Z;
o R_dist := the total hop count of all edges in the path;
o R_dist := the total metric of all edges in the path.
Finally, Routing Tuples of the second type whose R_dest_addr is not
routable MAY be discarded.
An example algorithm for calculating the Routing Set of a router is
given in Appendix B.
20. Proposed Values for Parameters and Constants
This protocol uses all parameters and constants defined in [RFC6130]
and additional parameters and constants defined in this
specification. All but one (RX_HOLD_TIME) of these additional
parameters are router parameters as defined in [RFC6130]. These
proposed values of the additional parameters are appropriate to the
case where all parameters (including those defined in [RFC6130]) have
a single value. Proposed values for parameters defined in [RFC6130]
are given in that specification.
Clausen, et al. Expires January 27, 2012 [Page 71]
Internet-Draft OLSRv2 July 2011
20.1. Local History Time Parameters
o O_HOLD_TIME := 30 seconds
20.2. Message Interval Parameters
o TC_INTERVAL := 5 seconds
o TC_MIN_INTERVAL := TC_INTERVAL/4
20.3. Advertised Information Validity Time Parameters
o T_HOLD_TIME := 3 x TC_INTERVAL
o A_HOLD_TIME := T_HOLD_TIME
20.4. Received Message Validity Time Parameters
o RX_HOLD_TIME := 30 seconds
o P_HOLD_TIME := 30 seconds
o F_HOLD_TIME := 30 seconds
20.5. Jitter Time Parameters
o TP_MAXJITTER := HP_MAXJITTER
o TT_MAXJITTER := HT_MAXJITTER
o F_MAXJITTER := TT_MAXJITTER
20.6. Hop Limit Parameter
o TC_HOP_LIMIT := 255
20.7. Willingness Parameter and Constants
o WILLINGNESS := WILL_DEFAULT
o WILL_NEVER := 0
o WILL_DEFAULT := 7
o WILL_ALWAYS := 15
Clausen, et al. Expires January 27, 2012 [Page 72]
Internet-Draft OLSRv2 July 2011
21. Sequence Numbers
Sequence numbers are used in this specification for the purpose of
discarding "old" information, i.e., messages received out of order.
However with a limited number of bits for representing sequence
numbers, wrap-around (that the sequence number is incremented from
the maximum possible value to zero) will occur. To prevent this from
interfering with the operation of this protocol, the following MUST
be observed when determining the ordering of sequence numbers.
The term MAXVALUE designates in the following one more than the
largest possible value for a sequence number. For a 16 bit sequence
number (as are those defined in this specification) MAXVALUE is
65536.
The sequence number S1 is said to be "greater than" the sequence
number S2 if:
o S1 > S2 AND S1 - S2 < MAXVALUE/2 OR
o S2 > S1 AND S2 - S1 > MAXVALUE/2
When sequence numbers S1 and S2 differ by MAXVALUE/2 their ordering
cannot be determined. In this case, which should not occur, either
ordering may be assumed.
Thus when comparing two messages, it is possible - even in the
presence of wrap-around - to determine which message contains the
most recent information.
22. Extensions
An extension to this protocol will need to interact with this
specification, and possibly also with [RFC6130]. This protocol is
designed to permit such interactions, in particular:
o Through accessing, and possibly extending, the information in the
Information Bases. All updates to the elements specified in this
specification are subject to the constraints specified in
[RFC6130] and Appendix D.
o Through accessing an outgoing message prior to it being
transmitted over any OLSRv2 interface, and to add information to
it as specified in [RFC5444]. This MAY include Message TLVs
and/or network addresses with associated Address Block TLVs.
(Network addresses without new associated TLVs SHOULD NOT be added
to messages.) This may, for example, be to allow a security
protocol, as suggested in Section 23, to add a TLV containing a
Clausen, et al. Expires January 27, 2012 [Page 73]
Internet-Draft OLSRv2 July 2011
cryptographic signature to the message.
o Through accessing an incoming message, and potentially discarding
it prior to processing by this protocol. This may, for example,
allow a security protocol as suggested in Section 23 to perform
verification of message signatures and prevent processing and/or
forwarding of unverifiable messages by this protocol.
o Through accessing an incoming message after it has been completely
processed by this protocol. This may, in particular, allow a
protocol which has added information, by way of inclusion of
appropriate TLVs, or of network addresses associated with new
TLVs, access to such information after appropriate updates have
been recorded in the Information Bases in this protocol.
o Through requesting that a message be generated at a specific time.
In that case, message generation MUST still respect the
constraints in [RFC6130] and Section 5.4.3.
23. Security Considerations
Currently, this protocol does not specify any special security
measures. As a proactive routing protocol, this protocol is a
potential target for various attacks. Various possible
vulnerabilities are discussed in this section.
23.1. Confidentiality
This protocol periodically MPR floods topological information to all
routers in the network. Hence, if used in an unprotected wireless
network, the network topology is revealed to anyone who listens to
the control messages.
In situations where the confidentiality of the network topology is of
importance, regular cryptographic techniques, such as exchange of
OLSRv2 control traffic messages encrypted by PGP [RFC4880] or
encrypted by some shared secret key, can be applied to ensure that
control traffic can be read and interpreted by only those authorized
to do so.
23.2. Integrity
Each router is injecting topological information into the network
through transmitting HELLO messages and, for some routers, TC
messages. If some routers for some reason, malicious or malfunction,
inject invalid control traffic, network integrity may be compromised.
Therefore, message authentication is recommended.
Clausen, et al. Expires January 27, 2012 [Page 74]
Internet-Draft OLSRv2 July 2011
Different such situations may occur, for instance:
1. a router generates TC messages, advertising links to non-neighbor
routers;
2. a router generates TC messages, pretending to be another router;
3. a router generates HELLO messages, advertising non-neighbor
routers;
4. a router generates HELLO messages, pretending to be another
router;
5. a router forwards altered control messages;
6. a router does not forward control messages;
7. a router does not select multipoint relays correctly;
8. a router forwards broadcast control messages unaltered, but does
not forward unicast data traffic;
9. a router "replays" previously recorded control traffic from
another router.
Authentication of the originator router for control messages (for
situations 2, 4 and 5) and on the individual links announced in the
control messages (for situations 1 and 3) may be used as a
countermeasure. However to prevent routers from repeating old (and
correctly authenticated) information (situation 9) temporal
information is required, allowing a router to positively identify
such delayed messages.
In general, digital signatures and other required security
information may be transmitted as a separate Message Type, or
signatures and security information may be transmitted within the
HELLO and TC messages, using the TLV mechanism. Either option
permits that "secured" and "unsecured" routers can coexist in the
same network, if desired,
Specifically, the authenticity of entire control packets can be
established through employing IPsec authentication headers, whereas
authenticity of individual links (situations 1 and 3) require
additional security information to be distributed.
An important consideration is that all control messages are
transmitted either to all routers in the neighborhood (HELLO
messages) or broadcast to all routers in the network (TC messages).
Clausen, et al. Expires January 27, 2012 [Page 75]
Internet-Draft OLSRv2 July 2011
For example, a control message in this protocol is always a point-to-
multipoint transmission. It is therefore important that the
authentication mechanism employed permits that any receiving router
can validate the authenticity of a message. As an analogy, given a
block of text, signed by a PGP private key, then anyone with the
corresponding public key can verify the authenticity of the text.
23.3. Interaction with External Routing Domains
This protocol does, through the use of TC messages, provide a basic
mechanism for injecting external routing information to this
protocol's domain. Routing information can be extracted from the
protocol's Information Bases, in particular the Routing Set, of this
protocol and, potentially, injected into an external domain, if the
routing protocol governing that domain permits this.
When operating routers connecting a MANET using this protocol to an
external routing domain, care MUST be taken not to allow potentially
insecure and untrustworthy information to be injected from this
domain to external routing domains. Care MUST also be taken to
validate the correctness of information prior to it being injected as
to avoid polluting routing tables with invalid information.
A recommended way of extending connectivity from an existing routing
domain to a MANET routed using this protocol is to assign an IP
prefix (under the authority of the routers/gateways connecting the
MANET with the exiting routing domain) exclusively to that MANET
area, and to statically configure the gateways to advertise routes
for that IP sequence to routers in the existing routing domain.
24. IANA Considerations
This specification defines one Message Type, which must be allocated
from the "Message Types" repository of [RFC5444], two Message TLV
Types, which must be allocated from the "Message TLV Types"
repository of [RFC5444], and four Address Block TLV Types, which must
be allocated from the "Address Block TLV Types" repository of
[RFC5444].
24.1. Expert Review: Evaluation Guidelines
For the registries where an Expert Review is required, the designated
expert SHOULD take the same general recommendations into
consideration as are specified by [RFC5444].
Clausen, et al. Expires January 27, 2012 [Page 76]
Internet-Draft OLSRv2 July 2011
24.2. Message Types
This specification defines one Message Type, to be allocated from the
0-223 range of the "Message Types" namespace defined in [RFC5444], as
specified in Table 8.
+------+----------------------------------------------+
| Type | Description |
+------+----------------------------------------------+
| TBD1 | TC : Topology Control (MANET-wide signaling) |
+------+----------------------------------------------+
Table 8: Message Type assignment
24.3. Message-Type-specific TLV Type Registries
IANA is requested to create a registry for Message-Type-specific
Message TLVs for TC messages, in accordance with Section 6.2.1 of
[RFC5444], and with initial assignments and allocation policies as
specified in Table 9.
+---------+-------------+-------------------+
| Type | Description | Allocation Policy |
+---------+-------------+-------------------+
| 128-223 | Unassigned | Expert Review |
+---------+-------------+-------------------+
Table 9: TC Message-Type-specific Message TLV Types
IANA is requested to create a registry for Message-Type-specific
Address Block TLVs for TC messages, in accordance with Section 6.2.1
of [RFC5444], and with initial assignments and allocation policies as
specified in Table 10.
+---------+-------------+-------------------+
| Type | Description | Allocation Policy |
+---------+-------------+-------------------+
| 128-223 | Unassigned | Expert Review |
+---------+-------------+-------------------+
Table 10: TC Message-Type-specific Address Block TLV Types
24.4. Message TLV Types
This specification defines two Message TLV Types, which must be
allocated from the "Message TLV Types" namespace defined in
[RFC5444]. IANA is requested to make allocations in the 0-127 range
for these types. This will create two new Type Extension registries
Clausen, et al. Expires January 27, 2012 [Page 77]
Internet-Draft OLSRv2 July 2011
with assignments as specified in Table 11 and Table 12.
Specifications of these TLVs are in Section 13.3.1. Each of these
TLVs MUST NOT be included more than once in a Message TLV Block.
+-------------+------+-----------+---------------------+------------+
| Name | Type | Type | Description | Allocation |
| | | Extension | | Policy |
+-------------+------+-----------+---------------------+------------+
| MPR_WILLING | TBD2 | 0 | Bits 0-3 encode | |
| | | | specify the | |
| | | | originating | |
| | | | router's | |
| | | | willingness to act | |
| | | | as a flooding | |
| | | | relay; bits 4-7 | |
| | | | encode specify the | |
| | | | originating | |
| | | | router's | |
| | | | willingness to act | |
| | | | as a routing relay | |
| MPR_WILLING | TBD2 | 1-255 | Unassigned | Expert |
| | | | | Review |
+-------------+------+-----------+---------------------+------------+
Table 11: Message TLV Type assignment: MPR_WILLING
+--------------+------+-----------+--------------------+------------+
| Name | Type | Type | Description | Allocation |
| | | Extension | | Policy |
+--------------+------+-----------+--------------------+------------+
| CONT_SEQ_NUM | TBD3 | 0 | COMPLETE : | |
| | | | Specifies a | |
| | | | content sequence | |
| | | | number for this | |
| | | | complete message | |
| CONT_SEQ_NUM | TBD3 | 1 | INCOMPLETE : | |
| | | | Specifies a | |
| | | | content sequence | |
| | | | number for this | |
| | | | incomplete message | |
| CONT_SEQ_NUM | TBD3 | 2-255 | Unassigned | Expert |
| | | | | Review |
+--------------+------+-----------+--------------------+------------+
Table 12: Message TLV Type assignment: CONT_SEQ_NUM
Type extensions indicated as Expert Review SHOULD be allocated as
described in [RFC5444], based on Expert Review as defined in
Clausen, et al. Expires January 27, 2012 [Page 78]
Internet-Draft OLSRv2 July 2011
[RFC5226].
24.5. Address Block TLV Types
This specification defines four Address Block TLV Types, which must
be allocated from the "Address Block TLV Types" namespace defined in
[RFC5444]. IANA are requested to make allocations in the 8-127 range
for these types. This will create four new Type Extension registries
with assignments as specified in Table 13, Table 14, Table 15 and
Table 16. Specifications of these TLVs are in Section 13.3.2.
+-------------+------+-----------+-------------------+--------------+
| Name | Type | Type | Description | Allocation |
| | | Extension | | Policy |
+-------------+------+-----------+-------------------+--------------+
| LINK_METRIC | TBD4 | 0 | Link metric | |
| | | | meaning assigned | |
| | | | by administrative | |
| | | | action | |
| LINK_METRIC | TBD4 | 1-223 | Unassigned | Expert |
| | | | | Review |
| LINK_METRIC | TBD4 | 224-255 | Unassigned | Experimental |
| | | | | Use |
+-------------+------+-----------+-------------------+--------------+
Table 13: Address Block TLV Type assignment: LINK_METRIC
All LINK_METRIC TLVs, whatever their type extension, MUST use their
value field to encode the kind and value (in the interval
MINIMUM_METRIC, to MAXIMUM_METRIC, inclusive) of a link metric as
specified in Section 6 and Section 13.3.2. An assignment of a
LINK_METRIC TLV type extension MUST specify the physical meaning, and
mapping of that physical meaning to the representable values in the
indicated interval, of the link metric.
Clausen, et al. Expires January 27, 2012 [Page 79]
Internet-Draft OLSRv2 July 2011
+------+------+-----------+----------------------------+------------+
| Name | Type | Type | Description | Allocation |
| | | Extension | | Policy |
+------+------+-----------+----------------------------+------------+
| MPR | TBD5 | 0 | Specifies that a given | |
| | | | network address is of a | |
| | | | router selected as a | |
| | | | flooding MPR (FLOODING = | |
| | | | 1), that a given network | |
| | | | address is of a router | |
| | | | selected as a routing MPR | |
| | | | (ROUTING = 2), or both | |
| | | | (FLOOD_ROUTE = 3) | |
| MPR | TBD5 | 1-255 | Unassigned | Expert |
| | | | | Review |
+------+------+-----------+----------------------------+------------+
Table 14: Address Block TLV Type assignment: MPR
+---------------+------+-----------+-------------------+------------+
| Name | Type | Type | Description | Allocation |
| | | Extension | | Policy |
+---------------+------+-----------+-------------------+------------+
| NBR_ADDR_TYPE | TBD6 | 0 | Specifies that a | |
| | | | given network | |
| | | | address is of a | |
| | | | neighbor reached | |
| | | | via the | |
| | | | originating | |
| | | | router, if it is | |
| | | | an originator | |
| | | | address | |
| | | | (ORIGINATOR = 1), | |
| | | | is a routable | |
| | | | address (ROUTABLE | |
| | | | = 2), or if it is | |
| | | | both | |
| | | | (ROUTABLE_ORIG = | |
| | | | 3) | |
| NBR_ADDR_TYPE | TBD6 | 1-255 | Unassigned | Expert |
| | | | | Review |
+---------------+------+-----------+-------------------+------------+
Table 15: Address Block TLV Type assignment: NBR_ADDR_TYPE
Clausen, et al. Expires January 27, 2012 [Page 80]
Internet-Draft OLSRv2 July 2011
+---------+------+-----------+-------------------------+------------+
| Name | Type | Type | Description | Allocation |
| | | extension | | Policy |
+---------+------+-----------+-------------------------+------------+
| GATEWAY | TBD7 | 0 | Specifies that a given | |
| | | | network address is | |
| | | | reached via a gateway | |
| | | | on the originating | |
| | | | router, with value | |
| | | | equal to the number of | |
| | | | hops | |
| GATEWAY | TBD7 | 1-255 | | Expert |
| | | | | Review |
+---------+------+-----------+-------------------------+------------+
Table 16: Address Block TLV Type assignment: GATEWAY
Type extensions indicated as Expert Review SHOULD be allocated as
described in [RFC5444], based on Expert Review as defined in
[RFC5226].
24.6. NBR_ADDR_TYPE Values
Note: This section does not require any IANA action, as the required
information is included in the descriptions of the MPR and
NBR_ADDR_TYPE Address Block TLVs allocated in Section 24.5. This
information is recorded here for clarity, and for use elsewhere in
this specification.
The Values which the MPR Address Block TLV can use are the following:
o FLOODING := 1;
o ROUTING := 2;
o FLOOD_ROUTE := 3.
The Values which the NBR_ADDR_TYPE Address Block TLV can use are the
following:
o ORIGINATOR := 1;
o ROUTABLE := 2;
o ROUTABLE_ORIG := 3.
Clausen, et al. Expires January 27, 2012 [Page 81]
Internet-Draft OLSRv2 July 2011
25. Contributors
This specification is the result of the joint efforts of the
following contributors -- listed alphabetically.
o Cedric Adjih, INRIA, France, <Cedric.Adjih@inria.fr>
o Emmanuel Baccelli, INRIA , France, <Emmanuel.Baccelli@inria.fr>
o Thomas Heide Clausen, LIX, France, <T.Clausen@computer.org>
o Justin Dean, NRL, USA, <jdean@itd.nrl.navy.mil>
o Christopher Dearlove, BAE Systems, UK,
<chris.dearlove@baesystems.com>
o Satoh Hiroki, Hitachi SDL, Japan, <hiroki.satoh.yj@hitachi.com>
o Philippe Jacquet, INRIA, France, <Philippe.Jacquet@inria.fr>
o Monden Kazuya, Hitachi SDL, Japan, <kazuya.monden.vw@hitachi.com>
o Kenichi Mase, Niigata University, Japan, <mase@ie.niigata-u.ac.jp>
o Ryuji Wakikawa, Toyota, Japan, <ryuji@sfc.wide.ad.jp>
26. Acknowledgments
The authors would like to acknowledge the team behind OLSRv1,
specified in RFC3626, including Anis Laouiti (INT, Paris), Pascale
Minet (INRIA, France), Laurent Viennot (INRIA, France), and Amir
Qayyum (M.A. Jinnah University, Islamabad) for their contributions.
The authors would like to gratefully acknowledge the following people
for intense technical discussions, early reviews and comments on the
specification and its components (listed alphabetically): Khaldoun Al
Agha (LRI), Teco Boot (Infinity Networks), Song-Yean Cho (LIX), Alan
Cullen (BAE Systems), Louise Lamont (CRC), Li Li (CRC), Joe Macker
(NRL), Richard Ogier (SRI), Charles E. Perkins (WiChorus), Henning
Rogge (FGAN), and the entire IETF MANET working group.
27. References
27.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, BCP 14, March 1997.
Clausen, et al. Expires January 27, 2012 [Page 82]
Internet-Draft OLSRv2 July 2011
[RFC5148] Clausen, T., Dearlove, C., and B. Adamson, "Jitter
Considerations in Mobile Ad Hoc Networks (MANETs)",
RFC 5148, February 2008.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", RFC 5226, BCP 26,
May 2008.
[RFC5444] Clausen, T., Dean, J., Dearlove, C., and C. Adjih,
"Generalized Mobile Ad Hoc Network (MANET) Packet/
Message Format", RFC 5444, February 2009.
[RFC5497] Clausen, T. and C. Dearlove, "Representing Multi-Value
Time in Mobile Ad Hoc Networks (MANETs)", RFC 5497,
March 2009.
[RFC5498] Chakeres, I., "IANA Allocations for Mobile Ad Hoc
Network (MANET) Protocols", RFC 5498, March 2009.
[RFC6130] Clausen, T., Dean, J., and C. Dearlove, "Mobile Ad Hoc
Network (MANET) Neighborhood Discovery Protocol (NHDP)",
RFC 6130, April 2011.
27.2. Informative References
[RFC2501] Macker, J. and S. Corson, "Mobile Ad hoc Networking
(MANET): Routing Protocol Performance Issues and
Evaluation Considerations", RFC 2501, January 1999.
[RFC3626] Clausen, T. and P. Jacquet, "The Optimized Link State
Routing Protocol", RFC 3626, October 2003.
[RFC4880] Callas, J., Donnerhacke, L., Finney, H., and R. Thayer,
"OpenPGP message format", RFC 4880, November 2007.
[HIPERLAN] ETSI, "ETSI STC-RES10 Committee. Radio equipment and
systems: HIPERLAN type 1, functional specifications ETS
300-652", June 1996.
[HIPERLAN2] Jacquet, P., Minet, P., Muhlethaler, P., and N.
Rivierre, "Increasing reliability in cable free radio
LANs: Low level forwarding in HIPERLAN.", 1996.
[MPR] Qayyum, A., Viennot, L., and A. Laouiti, "Multipoint
relaying: An efficient technique for flooding in mobile
wireless networks.", 2001.
[FSR] Pei, G., Gerla, M., and T. Chen, "Fisheye state routing
Clausen, et al. Expires January 27, 2012 [Page 83]
Internet-Draft OLSRv2 July 2011
in mobile ad hoc networks", 2000.
[FSLS] Santivanez, C., Ramanathan, R., and I. Stavrakakis,
"Making link-state routing scale for ad hoc networks",
2000.
Appendix A. Example Algorithm for Calculating MPRs
Note: This appendix has not yet been updated to use link metrics and
separate sets of flooding and routing MPRs.
The following specifies an algorithm which MAY be used to select
MPRs. MPRs are calculated per OLSRv2 interface, but then a single
set of MPRs is formed from the union of the MPRs for all OLSRv2
interfaces. (As noted in Section 18 a router MAY improve on this, by
coordination between OLSRv2 interfaces.) A router's MPRs are
recorded using the element N_mpr in Neighbor Tuples.
If using this example algorithm then the following steps MUST be
executed in order for a router to select its MPRs:
1. Set N_mpr := false in all Neighbor Tuples;
2. For each Neighbor Tuple with N_symmetric = true and N_willingness
= WILL_ALWAYS, set N_mpr := true;
3. For each OLSRv2 interface of the router, use the algorithm in
Appendix A.2. Note that this sets N_mpr := true for some
Neighbor Tuples, these routers are already selected as MPRs when
using the algorithm for following OLSRv2 interfaces.
4. OPTIONALLY, consider each selected MPR in turn, and if the set of
selected MPRs without that router still satisfies the necessary
conditions, for all OLSRv2 interfaces, then that router MAY be
removed from the set of MPRs. This process MAY be repeated until
no MPRs are removed. Routers MAY be considered in order of
increasing N_willingness.
Note that only symmetric strict 2-hop neighbors are considered, thus:
o Symmetric 1-hop neighbor routers with N_willingness = WILL_NEVER
MUST NOT be selected as MPRs, and MUST be ignored in the following
algorithm (and hence also ignore any 2-Hop Tuples whose
N2_neighbor_iface_addr_list is included in the
N_neighbor_addr_list of any such Neighbor Tuple).
o Symmetric 2-hop neighbor routers which are also symmetric 1-hop
neighbor routers MUST be ignored in the following algorithm (i.e.,
Clausen, et al. Expires January 27, 2012 [Page 84]
Internet-Draft OLSRv2 July 2011
ignore any 2-Hop Tuples whose N2_2hop_addr is in the
N_neighbor_addr_list of any Neighbor Tuple).
A.1. Terminology
The following terminology will be used when selecting MPRs for the
OLSRv2 interface I:
N(I) - The set of symmetric 1-hop neighbors which have a symmetric
link to I.
N2(I) - The set of network addresses of interfaces of a router with
a symmetric link to a router in N(I); this MAY be restricted to
considering only information received over I (in which case N2(I)
is the set of N2_2hop_addr in 2-Hop Tuples in the 2-Hop Set for
OLSRv2 interface I).
Connected to I via Y - A network address A in N2(I) is connected to
I via a router Y in N(I) if A is a network address of an interface
of a symmetric 1-hop neighbor of Y (i.e., A is the N2_2hop_addr in
a 2-Hop Tuple in the 2-Hop Set for OLSRv2 interface I, and whose
N2_neighbor_iface_addr_list is contained in the set of interface
network addresses of Y).
D(Y, I) - For a router Y in N(I), the number of network addresses in
N2(I) which are connected to I via Y.
R(Y, I): - For a router Y in N(I), the number of network addresses
in N2(I) which are connected to I via Y, but are not connected to
I via any router which has already been selected as an MPR.
A.2. MPR Selection Algorithm for each OLSRv2 Interface
When selecting MPRs for the OLSRv2 interface I:
1. For each network address A in N2(I) for which there is only one
router Y in N(I) such that A is connected to I via Y, select that
router Y as an MPR (i.e., set N_mpr := true in the Neighbor Tuple
corresponding to Y).
2. While there exists any router Y in N(I) with R(Y, I) > 0:
1. Select a router Y in N(I) with R(Y, I) > 0 in the following
order of priority:
+ greatest N_willingness in the Neighbor Tuple corresponding
to Y, THEN;
Clausen, et al. Expires January 27, 2012 [Page 85]
Internet-Draft OLSRv2 July 2011
+ greatest R(Y, I), THEN;
+ greatest D(Y, I), THEN;
+ N_mpr_selector is equal to true, if possible, THEN;
+ any choice.
2. Select Y as an MPR (i.e., set N_mpr := true in the Neighbor
Tuple corresponding to Y).
Appendix B. Example Algorithm for Calculating the Routing Set
The following procedure is given as an example for calculating the
Routing Set using a variation of Dijkstra's algorithm. First all
Routing Tuples are removed, and then, using the selections and
definitions in Appendix B.1, the procedures in the following sections
(each considered a "stage" of the processing) are applied in turn.
B.1. Local Interfaces and Neighbors
The following selections and definitions are made:
1. For each Local Interface Tuple, select a network address from its
I_local_iface_addr_list, this is defined as the selected address
for this Local Interface Tuple.
2. For each Link Tuple, the selected address of its corresponding
Local Interface Tuple is defined as the selected local address
for this Local Interface Tuple.
3. For each Neighbor Tuple with N_symmetric = true, select a Link
Tuple with L_status = SYMMETRIC for which this is the
corresponding Neighbor Tuple and has L_out_metric = N_out_metric.
This is defined as the selected Link Tuple for this Neighbor
Tuple.
4. For each network address (N_orig_addr or in N_neighbor_addr_list,
the "neighbor address") from a Neighbor Tuple with N_symmetric =
true, select a Link Tuple (the "selected Link Tuple") from those
for which this is the corresponding Neighbor Tuple, have L_status
= SYMMETRIC, and have L_out_metric = N_out_metric, by:
1. If there is such a Link Tuple whose
L_neighbor_iface_addr_list contains the neighbor address,
select that Link Tuple.
Clausen, et al. Expires January 27, 2012 [Page 86]
Internet-Draft OLSRv2 July 2011
2. Otherwise select the selected Link Tuple for this Neighbor
Tuple.
Then for this neighbor address:
3. The selected local address is defined as the selected local
address for the selected Link Tuple.
4. The selected link address is defined as an address from the
L_neighbor_iface_addr_list of the selected Link Tuple, if
possible equal to this neighbor address.
5. Routing Tuple preference is decided by preference for minimum
R_dist, and then for preference for corresponding Neighbor Tuples
in this order:
* For greater N_willingness.
* For N_mpr_selector = true over N_mpr_selector = false.
Note that preferred Routing Tuples SHOULD be used. Routing
Tuples with minimum R_metric MUST be used, this is specified
outside the definition of preference. An implementation MAY
modify this definition of preference without otherwise affecting
this algorithm.
B.2. Add Neighbor Routers
The following procedure is executed once.
1. For each Neighbor Tuple with N_symmetric = true, add a Routing
Tuple with:
* R_dest_addr := N_orig_addr;
* R_next_iface_addr := selected link address for N_orig_addr;
* R_local_iface_addr := selected local address for N_orig_addr;
* R_metric := N_out_metric;
* R_dist := 1.
B.3. Add Remote Routers
The following procedure is executed for each value of h, starting
with h := 1 and incrementing by 1 for each iteration. The execution
MUST stop if no Routing Tuples are added or modified in an iteration.
Clausen, et al. Expires January 27, 2012 [Page 87]
Internet-Draft OLSRv2 July 2011
1. For each Router Topology Tuple, if:
* TR_from_orig_addr is equal to the R_dest_addr of a Routing
Tuple with R_dist = h (the "previous Routing Tuple"),
then consider the candidate Routing Tuple with:
* R_dest_addr := TR_to_orig_addr;
* R_next_iface_addr := R_next_iface_addr of the previous Routing
Tuple;
* R_local_iface_addr := R_local_iface_addr of the previous
Routing Tuple;
* R_metric := R_metric of the previous Routing Tuple +
TR_metric;
* R_dist := h+1.
This candidate Routing Tuple MUST be added to the Routing Set if
there is no existing Routing Tuple with the same R_dest_addr.
Otherwise this candidate Routing Tuple MUST replace the existing
Routing Tuple with the same R_dest_addr if this candidate Routing
Tuple has a smaller R_metric, this candidate Routing Tuple SHOULD
replace the existing Routing Tuple with the same R_dest_addr if
this candidate Routing Tuple has an equal R_metric and is
preferred to the existing Routing Tuple.
B.4. Add Neighbor Addresses
The following procedure is executed once.
1. For each Neighbor Tuple with N_symmetric = true:
1. For each network address (the "neighbor address") in
N_neighbor_addr_list, if the neighbor address is not equal to
the R_dest_addr of any Routing Tuple, then add a new Routing
Tuple, with:
+ R_dest_addr := neighbor address;
+ R_next_iface_addr := selected link address for the
neighbor address;
+ R_local_iface_addr := selected local address for the
neighbor address;
Clausen, et al. Expires January 27, 2012 [Page 88]
Internet-Draft OLSRv2 July 2011
+ R_metric := N_out_metric;
+ R_dist := 1.
B.5. Add Remote Routable Addresses
The following procedure is executed once.
1. For each Routable Address Topology Tuple, if:
* TA_dest_addr is not equal to the R_dest_addr of any Routing
Tuple added in an earlier stage, AND;
* TA_from_orig_addr is equal to the R_dest_addr of a Routing
Tuple (the "previous Routing Tuple"),
then add a new Routing Tuple, with:
* R_dest_addr := TA_dest_addr;
* R_next_iface_addr := R_next_iface_addr of the previous Routing
Tuple;
* R_local_iface_addr := R_local_iface_addr of the previous
Routing Tuple;
* R_metric := R_metric of the previous Routing Tuple +
TA_metric.
* R_dist := R_dist of the previous Routing Tuple + 1.
There may be more than one Routing Tuple that may be added for an
R_dest_addr in this stage. If so, then, for each such
R_dest_addr, a Routing Tuple with minimum R_metric MUST be
selected, otherwise a Routing Tuple which is preferred SHOULD be
added.
B.6. Add Attached Networks
The following procedure is executed once.
1. For each Attached Network Tuple, if:
* AN_net_addr is not equal to the R_dest_addr of any Routing
Tuple added in an earlier stage, AND;
* AN_orig_addr is equal to the R_dest_addr of a Routing Tuple
(the "previous Routing Tuple),
Clausen, et al. Expires January 27, 2012 [Page 89]
Internet-Draft OLSRv2 July 2011
then add a new Routing Tuple, with:
* R_dest_addr := AN_net_addr;
* R_next_iface_addr := R_next_iface_addr of the previous Routing
Tuple;
* R_local_iface_addr := R_local_iface_addr of the previous
Routing Tuple;
* R_metric := R_metric of the previous Routing Tuple +
AN_metric;
* R_dist := R_dist of the previous Routing Tuple + AN_dist.
There may be more than one Routing Tuple that may be added for an
R_dest_addr in this stage. If so, then, for each such
R_dest_addr, a Routing Tuple with minimum R_metric MUST be
selected, otherwise a Routing Tuple which is preferred SHOULD be
added.
B.7. Add 2-Hop Neighbors
The following procedure is executed once.
1. For each 2-Hop Tuple, if:
* N2_2hop_addr is a routable address, AND;
* N2_2hop_addr is not equal to the R_dest_addr of any Routing
Tuple added in an earlier stage, AND;
* the Routing Tuple with R_dest_addr = N_orig_addr of the
corresponding Neighbor Tuple (the "previous Routing Tuple")
has R_dist = 1,
then add a new Routing Tuple, with:
* R_dest_addr := N2_2hop_addr;
* R_next_iface_addr := R_next_iface_addr of the previous Routing
Tuple;
* R_local_iface_addr := R_local_iface_addr of the previous
Routing Tuple;
* R_metric := R_metric of the previous Routing Tuple +
N_out_metric of the corresponding Neighbor Tuple;
Clausen, et al. Expires January 27, 2012 [Page 90]
Internet-Draft OLSRv2 July 2011
* R_dist := 2.
There may be more than one Routing Tuple that may be added for an
R_dest_addr in this stage. If so, then, for each such
R_dest_addr, a Routing Tuple with minimum R_metric MUST be
selected, otherwise a Routing Tuple which is preferred SHOULD be
added.
Appendix C. TC Message Example
TC messages are instances of [RFC5444] messages. This specification
requires that TC messages contains <msg-hop-limit> and <msg-orig-
addr> fields. It supports TC messages with any combination of
remaining message header options and address encodings, enabled by
[RFC5444] that convey the required information. As a consequence,
there is no single way to represent how all TC messages look. This
appendix illustrates a TC message, the exact values and content
included are explained in the following text.
The TC message's four bit Message Flags (MF) field has value 15
indicating that the message header contains originaor address, hop
limit, hop count, and message sequence number fields. Its four bit
Message Address Length (MAL) field has value 3, indicating addresses
in the message have a length of four octets, here being IPv4
addresses. The overall message length is 71 octets.
The message has a Message TLV Block with content length 13 octets
containing three TLVs. The first two TLVs are validity and interval
times for the message. The third TLV is the content sequence number
TLV used to carry the 2 octet ANSN, and (with default type extension
zero, i.e., COMPLETE) indicating that the TC message is complete.
Each TLV uses a TLV with Flags octet (MTLVF) value 16, indicating
that it has a Value, but no type extension or start and stop indexes.
The first two TLVs have a Value Length of 1 octet, the last has a
Value Length of 2 octets.
The message has two Address Blocks. (This is not necessary, the
information could be conveyed using a single Address Block, the use
of two Address Blocks, which is also allowed, is illustrative only.)
The first Address Block contains 3 addresses, with Flags octet
(ATLVF) value 128, hence with a Head section (with length 2 octets),
but no Tail section, and hence with Mid sections with length two
octets. The following TLV Block (content length 13 octets) contains
two TLVs. The first TLV is a NBR_ADDR_TYPE TLV with Flags octet
(ATLVF) value 16, indicating a single Value but no indexes. Thus all
three addresses are associated with the Value (with Value Length 1
octet) ROUTABLE_ORIG, i.e., they are originator addresses of
advertised neighbors that are also routable addresses. The second
Clausen, et al. Expires January 27, 2012 [Page 91]
Internet-Draft OLSRv2 July 2011
TLV is a LINK_STATUS TLV with Flags octet (ATLVF) value 20,
indicating a Value for each address, i.e. as the total Value Length
is 6 octets, each address is associated with a Value with length two
octets. These Value fields are each shown as having four bits
indicating that they are outgoing neighbor metric values, and as
having twelve bits that represent the metric value (the first four
bits being the exponent, the remaining twelve bits the mantissa).
The second Address Block contains 1 address, with Flags octet (ATLVF)
176, indicating that there is a Head section (with length 2 octets),
that the Tail section (with length 2 octets) consists of zero valued
octets (not included), and that there is a single prefix length,
which is 16. The network address is thus Head.0.0/16. The following
TLV Block (content length 8 octets) includes two TLVs. The first has
a Flags octet (ATLVF) of 16, again indicating that no indexes are
needed, but that a Value (with Value Length 1 octet) is present,
indicating the address distance as a number of hops. The second TLV
is another LINK_METRIC TLV, as in the first Address TLV Block except
with a Flags octet (ATLVF) value 16, indicating that a single Value
is present.
Clausen, et al. Expires January 27, 2012 [Page 92]
Internet-Draft OLSRv2 July 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TC | MF=15 | MAL=3 | Message Length = 71 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Originator Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Hop Limit | Hop Count | Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Message TLV Block Length = 13 | VALIDITY_TIME | MTLVF = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value Len = 1 | Value (Time) | INTERVAL_TIME | MTLVF = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value Len = 1 | Value (Time) | CONT_SEQ_NUM | MTLVF = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value Len = 2 | Value (ANSN) | Num Addrs = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ABF = 128 | Head Len = 2 | Head |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Mid | Mid |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Mid | Address TLV Block Length = 13 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NBR_ADDR_TYPE | ATLVF = 16 | Value Len = 1 | ROUTABLE_ORIG |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LINK_METRIC | ATLVF = 20 | Value Len = 6 |0|0|0|1|Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Metric (cont) |0|0|0|1| Metric |0|0|0|1|Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Metric (cont) | Num Addrs = 1 | ABF = 176 | Head Len = 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Head | Tail Len = 2 | Pref Len = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address TLV Block Length = 9 | GATEWAY | ATLVF = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value Len = 1 | Value (Hops) | LINK_METRIC | ATLVF = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value Len = 2 |0|0|0|1| Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Appendix D. Constraints
Any process which updates the Local Information Base, the
Neighborhood Information Base or the Topology Information Base MUST
ensure that all constraints specified in this appendix are
maintained, as well as those specified in [RFC6130].
In each Originator Tuple:
Clausen, et al. Expires January 27, 2012 [Page 93]
Internet-Draft OLSRv2 July 2011
o O_orig_addr MUST NOT equal any other O_orig_addr.
o O_orig_addr MUST NOT equal this router's originator address.
In each Local Attached Network Tuple:
o AL_net_addr MUST NOT equal any other AL_net_addr.
o AL_net_addr MUST NOT equal or be a sub-range of any network
address in the I_local_iface_addr_list of any Local Interface
Tuple.
o AL_net_addr MUST NOT equal this router's originator address, or
equal the O_orig_addr in any Originator Tuple.
o AL_dist MUST NOT be less than zero.
In each Link Tuple:
o L_neighbor_iface_addr_list MUST NOT contain any network address
that AL_net_addr of any Local Attached Network Tuple equals or is
a sub-range of.
o If L_status = HEARD or L_status = SYMMETRIC then L_in_metric !=
UNKNOWN_METRIC.
o If L_status = SYMMETRIC then L_in_metric != UNKNOWN_METRIC.
o if L_in_metric != UNKNOWN_METRIC then L_in_metric MUST be
representable in the defined compressed form.
o if L_out_metric != UNKNOWN_METRIC then L_out_metric MUST be
representable in the defined compressed form.
o If L_mpr_selector = true, then L_status = SYMMETRIC.
In each Neighbor Tuple:
o N_orig_addr MUST NOT be changed to unknown.
o N_orig_addr MUST NOT equal this router's originator address, or
equal O_orig_addr in any Originator Tuple.
o N_orig_addr MUST NOT equal the AL_net_addr in any Local Attached
Network Tuple.
o If N_orig_addr != unknown, then N_orig_addr MUST NOT equal the
N_orig_addr in any other Neighbor Tuple.
Clausen, et al. Expires January 27, 2012 [Page 94]
Internet-Draft OLSRv2 July 2011
o N_neighbor_addr_list MUST NOT contain any network address which
includes this router's originator address, the O_orig_addr in any
Originator Tuple, or equal or have as a sub-range the AL_net_addr
in any Local Attached Network Tuple.
o If N_orig_addr = unknown, then N_willingness = WILL_NEVER, N_mpr =
false, N_mpr_selector = false, and N_advertised = false.
o N_in_metric MUST equal the minimum value of the L_in_metric values
of all corrsponding Link Tuples, if any, otherwise N_in_metric =
UNKNOWN_METRIC.
o N_out_metric MUST equal the minimum value of the L_out_metric
values of all corrsponding Link Tuples, if any, otherwise
N_out_metric = UNKNOWN_METRIC.
o N_will_flooding and N_will_routing MUST be in the range from
WILL_NEVER to WILL_ALWAYS, inclusive.
o If N_flooding_mpr = true, then N_symmetric MUST be true and
N_will_flooding MUST NOT equal WILL_NEVER.
o If N_routing_mpr = true, then N_symmetric MUST be true and
N_will_routing MUST NOT equal WILL_NEVER.
o If N_symmetric = true and N_mpr_flooding = false, then
N_will_flooding MUST NOT equal WILL_ALWAYS.
o If N_symmetric = true and N_mpr_routing = false, then
N_will_routing MUST NOT equal WILL_ALWAYS.
o If N_mpr_selector = true, then N_advertised MUST be true.
o If N_advertised = true, then N_symmetric MUST be true.
In each Lost Neighbor Tuple:
o NL_neighbor_addr MUST NOT include this router's originator
address, the O_orig_addr in any Originator Tuple, or equal or have
as a sub-range the AL_net_addr in any Local Attached Network
Tuple.
In each 2-Hop Tuple:
o N2_2hop_addr MUST NOT equal this router's originator address,
equal the O_orig_addr in any Originator Tuple, or equal or have as
a sub-range the AL_net_addr in any Local Attached Network Tuple
Clausen, et al. Expires January 27, 2012 [Page 95]
Internet-Draft OLSRv2 July 2011
o N2_in_metric and N2_out_metric MUST be representable in the
defined compressed form.
In each Advertising Remote Router Tuple:
o AR_orig_addr MUST NOT be in any network address in the
I_local_iface_addr_list in any Local Interface Tuple or be in the
IR_local_iface_addr in any Removed Interface Address Tuple.
o AR_orig_addr MUST NOT equal this router's originator address or
equal the O_orig_addr in any Originator Tuple.
o AR_orig_addr MUST NOT be in the AL_net_addr in any Local Attached
Network Tuple.
o AR_orig_addr MUST NOT equal the AR_orig_addr in any other
Advertising Remote Router Tuple.
In each Router Topology Tuple:
o There MUST be an Advertising Remote Router Tuple with AR_orig_addr
= TR_from_orig_addr.
o TR_to_orig_addr MUST NOT be in any network address in the
I_local_iface_addr_list in any Local Interface Tuple or be in the
IR_local_iface_addr in any Removed Interface Address Tuple.
o TR_to_orig_addr MUST NOT equal this router's originator address or
equal the O_orig_addr in any Originator Tuple.
o TR_to_orig_addr MUST NOT be in the AL_net_addr in any Local
Attached Network Tuple.
o The ordered pair (TR_from_orig_addr, TR_to_orig_addr) MUST NOT
equal the corresponding pair for any other Router Topology Tuple.
o TR_seq_number MUST NOT be greater than AR_seq_number in the
Advertising Remote Router Tuple with AR_orig_addr =
TR_from_orig_addr.
o TR_metric MUST be representable in the defined compressed form.
In each Routable Address Topology Tuple:
o There MUST be an Advertising Remote Router Tuple with AR_orig_addr
= TA_from_orig_addr.
Clausen, et al. Expires January 27, 2012 [Page 96]
Internet-Draft OLSRv2 July 2011
o TA_dest_addr MUST be routable.
o TA_dest_addr MUST NOT overlap any network address in the
I_local_iface_addr_list in any Local Interface Tuple or overlap
the IR_local_iface_addr in any Removed Interface Address Tuple.
o TA_dest_addr MUST NOT include this router's originator address or
include the O_orig_addr in any Originator Tuple.
o TA_dest_addr MUST NOT equal or have as a sub-range the AL_net_addr
in any Local Attached Network Tuple.
o The ordered pair (TA_from_orig_addr, TA_dest_addr) MUST NOT equal
the corresponding pair for any other Attached Network Tuple.
o TA_seq_number MUST NOT be greater than AR_seq_number in the
Advertising Remote Router Tuple with AR_orig_addr =
TA_from_orig_addr.
o TA_metric MUST be representable in the defined compressed form.
In each Attached Network Tuple:
o There MUST be an Advertising Remote Router Tuple with AR_orig_addr
= AN_orig_addr.
o AN_net_addr MUST NOT equal or be a sub-range of any network
address in the I_local_iface_addr_list in any Local Interface
Tuple or be a sub-range of the IR_local_iface_addr in any Removed
Interface Address Tuple.
o AN_net_addr MUST NOT equal this router's originator address or
equal the O_orig_addr in any Originator Tuple.
o AN_net_addr MUST NOT equal the AL_net_addr in any Local Attached
Network Tuple.
o The ordered pair (AN_orig_addr, AN_net_addr) MUST NOT equal the
corresponding pair for any other Attached Network Tuple.
o AN_seq_number MUST NOT be greater than AR_seq_number in the
Advertising Remote Router Tuple with AR_orig_addr = AN_orig_addr.
o AN_dist MUST NOT be less than zero.
o AN_metric MUST be representable in the defined compressed form.
Clausen, et al. Expires January 27, 2012 [Page 97]
Internet-Draft OLSRv2 July 2011
Appendix E. Flow and Congestion Control
Due to its proactive nature, this protocol has a natural control over
the flow of its control traffic. Routers transmit control messages
at predetermined rates specified and bounded by message intervals.
This protocol employs [RFC6130] for local signaling, embedding MPR
selection advertisement through a simple Address Block TLV, and
router willingness advertisement (if any) as a single Message TLV.
Local signaling, therefore, shares the characteristics and
constraints of [RFC6130].
Furthermore, the use of MPRs can greatly reduce the signaling
overhead from link state information dissemination in two ways,
attaining both flooding reduction and topology reduction. First,
using MPR flooding, the cost of distributing link state information
throughout the network is reduced, as compared to when using classic
flooding, since only MPRs need to forward link state declaration
messages. Second, the amount of link state information for a router
to declare is reduced to need only contain that router's MPR
selectors. This reduces the size of a link state declaration as
compared to declaring full link state information. In particular
some routers may not need to declare any such information. In dense
networks, the reduction of control traffic can be of several orders
of magnitude compared to routing protocols using classical flooding
[MPR]. This feature naturally provides more bandwidth for useful
data traffic and pushes further the frontier of congestion.
Since the control traffic is continuous and periodic, it keeps the
quality of the links used in routing more stable. However, using
some options, some control messages (HELLO messages or TC messages)
may be intentionally sent in advance of their deadline in order to
increase the responsiveness of the protocol to topology changes.
This may cause a small, temporary, and local increase of control
traffic, however this is at all times bounded by the use of minimum
message intervals.
Authors' Addresses
Thomas Heide Clausen
LIX, Ecole Polytechnique
Phone: +33 6 6058 9349
EMail: T.Clausen@computer.org
URI: http://www.ThomasClausen.org/
Clausen, et al. Expires January 27, 2012 [Page 98]
Internet-Draft OLSRv2 July 2011
Christopher Dearlove
BAE Systems ATC
Phone: +44 1245 242194
EMail: chris.dearlove@baesystems.com
URI: http://www.baesystems.com/
Philippe Jacquet
Project Hipercom, INRIA
Phone: +33 1 3963 5263
EMail: philippe.jacquet@inria.fr
Clausen, et al. Expires January 27, 2012 [Page 99]
