Internet-Draft 1st nibble July 2023
Kompella, et al. Expires 6 January 2024 [Page]
Workgroup:
MPLS Working Group
Internet-Draft:
draft-ietf-mpls-1stnibble-02
Updates:
RFC 4928 (if approved)
Published:
Intended Status:
Standards Track
Expires:
Authors:
K. Kompella
Juniper Networks
S. Bryant
University of Surrey 5GIC
M. Bocci
Nokia
G. Mirsky, Ed.
Ericsson
L. Andersson
Huawei Technologies
J. Dong
Huawei Technologies

IANA Registry for the First Nibble Following a Label Stack

Abstract

The goal of this memo is to create a new IANA registry (called the MPLS First Nibble registry) for the first nibble (4-bit field) immediately following an MPLS label stack. The memo offers a rationale for such a registry, describes how the registry should be managed, and provides some initial entries. Furthermore, this memo sets out some documentation requirements for registering new values. Finally, it provides some recommendations that make processing MPLS packets easier and more robust.

The relationship between the IANA IP Version Numbers and the MPLS First Nibble registry is described in this document.

This memo, if published, would update [RFC4928].

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 6 January 2024.

1. Introduction

An MPLS packet consists of a label stack, an optional "post-stack header" (PSH) and an optional embedded packet (in that order). By PSH, we mean existing artifacts such as Control Words, BIER headers and the like, as well as new types of PSH being discussed in the MPLS Open Design Team meetings. However, in the data plane, there are scant clues regarding the PSH, and no clue as to the type of embedded packet; this information is communicated via other means, such as the routing protocols that signal the labels in the stack. Nonetheless, in order to better handle an MPLS packet in the data plane, it is common practice for network equipment to "guess" the type of embedded packet. Such equipment may also need to process the PSH. Both of these require parsing the data after the label stack. To do this, the "first nibble" (the top four bits of the first octet following the label stack) is often used. Although some existing network devices may use such a method, it needs to be stressed that the correct interpretation of the MPLS first nibble (MFN) in a PSH can be made only in the context of the LSE or group of LSEs in the preceding label stack that characterize the type of the PSH, and that any attempt to rely on the value in any other context is unreliable.

The semantics and usage of the first nibble are not well documented, nor are the assignments of values. This memo serves three purposes:

  • To document the assignments already made.
  • To provide straighforward documentation of future assignments through the creation of an "MPLS First Nibble registry".
  • Provide a method for tracking usage by requiring more consistent documentation.
  • To reiterate the importance that any MPLS packet not carrying plain IPv4 or IPv6 packets MUST contain a PSH.

There have been suggestions during discussions at the MPLS Open Design Team meetings that this document may serve as a registry for the PSH "headers of headers" types; however, this change needs WG consensus.

1.1. Conventions and Definitions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

LSR:

label switching router.

MPLS packet:

one whose Layer 2 header declares the type to be MPLS. For Ethernet, that means the Ethertype is 0x8847 or 0x8848.

Label Stack:

(of an MPLS packet) all labels (four-octet fields) after the Layer 2 header, up to and including the label with the BoS bit set ([RFC3032]).

MPLS First Nibble (MFN):

the most significant four bits of the first octet following the label stack.

MPLS Payload:

all data after the label stack, including the MFN, an optional post-stack header, and the embedded packet.

Post-stack Header (PSH):

optional field of interest to the egress LSR (and possibly to transit LSRs). Examples include a control word or an associated channel. The PSH MUST indicate its length, so that a parser knows where the embedded packet starts.

Embedded Packet:

All octets beyond the PSH (if any). That could be an IPv4 or IPv6 packet (e.g., for traffic engineering of IP packets, or for a Layer 3 VPN [RFC4364]), an Ethernet packet (for VPLS ([RFC4761], [RFC4762]) or EVPN [RFC7432]), or some other type of Layer 2 frame [RFC4446].

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
X |                        Layer 2 Header                         | |
  |                                                               | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
                                            TC   S       TTL
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
Y |             Label-1                   | TC  |0|      TTL      | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |             Label-2                   | TC  |0|      TTL      | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |               ...                     | TC  |0|      TTL      | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |             Label-n                   | TC  |1|      TTL      | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 1: Example of an MPLS Packet With Label Stack
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
A | (MFN) |                   IP packet                           | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                             data                              | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                 ...                                |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                        end of IP packet                       | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/


  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
B | (MFN) |                 non-IP packet                         | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                             data                              | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                 ...                                |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                      end of non-IP packet                     | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/


  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
C | (MFN) |                      PSH                              | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                              PSH                              | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                 ...                                |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                          end of PSH                           | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  |                        embedded packet                        | |
  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 2

Figure 1 shows an MPLS packet with Layer 2 header X and a label stack Y ending with Label-n. Then, there are three examples of an MPLS payload. The complete MPLS packet thus would consist of [X Y A], or [X Y B], or [X Y C].

A. The first payload is a bare IP packet, i.e., no PSH. The MFN in this case overlaps with the IP version number.

B. The next payload is a bare non-IP packet; again, no PSH. The MFN here is the first nibble of the payload, whatever it happens to be.

C. The last example is an MPLS Payload that starts with a PSH followed by the embedded packet. Here, the embedded packet could be IP or non-IP.

2. Rationale

2.1. Why Look at the First Nibble

An MPLS packet can contain many types of embedded packets. The most common types are:

  1. An IPv4 packet (whose IP header has version number 4).
  2. An IPv6 packet (whose IP header has version number 6).
  3. A Layer 2 Ethernet frame (i.e., not including the Preamble or the Start frame delimiter), starting with the destination MAC address.

Many other packet types are possible, and in principle, any Layer 2 embedded packet is permissible; indeed, in the past, PPP, Frame Relay and ATM packets were reasonably common.

In addition, there may be a PSH ahead of the embedded packet, and it needs to be parsed. The MFN is currently used for both of these purposes.

2.1.1. Load Balancing

There are four common ways to load balance an MPLS packet:

  1. One can use the top label alone.
  2. One can do better by using all of the (non-SPL) labels in the stack.
  3. One can do even better by "divining" the type of embedded packet, and using fields from the guessed header.
  4. One can do best by using either an Entropy Label [RFC6790] or a FAT Pseudowire Label [RFC6391]; see Section 2.1.3.)

Load balancing based on just the top label means that all packets with that top label will go the same way -- this is far from ideal. Load balancing based on the entire label stack (not including SPLs) is better, but it may still be uneven. If, however, the embedded packet is an IP packet, then the combination of (<source IP address>, <dest IP address>, <transport protocol>, <source port>, and <dest port>) from the IP header of the embedded packet forms an excellent basis for load-balancing. This is what is typically used for load balancing IP packets.

An MPLS packet doesn't, however, carry a payload type identifier. There is a simple (but dangerous) heuristic that is commonly used to guess the type of the embedded packet. The first nibble, i.e., the four most significant bits of the first octet, of an IP header contains the IP version number. That, in turn, indicates where to find the relevant fields for load-balancing. The heuristic goes roughly as follows:

2.1.1.1. Heuristic for Load Balancing
  1. If the MFN is 0x4 (0100b), treat the payload as an IPv4 packet, and find the relevant fields for load-balancing on that basis.
  2. If the MFN is 0x6 (0110b), treat the payload as an IPv6 packet, and find the relevant fields for load-balancing on that basis.
  3. If the MFN is anything else, the MPLS payload is not an IP packet; fall back to load-balancing using the label stack.

This heuristic has been implemented in many (legacy) routers, and performs well in the case of Figure 2, A. However, this heuristic can work very badly for Figure 2, B. For example, if payload B is an Ethernet frame, then the MFN is the first nibble of the OUI of the destination MAC address, which can be 0x4 or 0x6, and if so would lead to very bad load-balancing. This behavior can happen to other types of non-IP payloads as well.

That, in turn, led to the idea of inserting a PSH (e.g., a pseudowire control word [RFC4385], a DetNet control word [RFC8964] or a BIER header [RFC8296]) where the MFN is NOT 0x4 or 0x6, to explicitly prevent forwarding engines from confusing the MPLS payload with an IP packet. [RFC8469] recommends the use of a control word when the embedded packet is an Ethernet frame. RFC 8469 was published at the request of the operator community and the IEEE RAC as a result of operational difficulties with pseudowires that did not contain the control word.

This memo introduces a requirement and a recommendation, the first building on the above; the second deprecating the use of the heuristic in Section 2.1.1.1. The intent of both of these is that legacy routers continue to operate as they have, with no new problems introduced as a result of this memo. However, new implementations SHOULD follow these recommendations for a more robust operation.

2.1.2. Requirement

Network equipment that complies with this memo MUST use a PSH with an MFN value that is neither 0x4 nor 0x6 in all cases when the MPLS payload is not an IP packet. Effectively, Figure 2, B is disallowed.

This replaces the following text from [RFC4928], section 3, paragraph 3:

"It is RECOMMENDED, however, those applications that depend upon in-order packet delivery and do not have an MFN value assigned, restrict the first nibble values to 0x0 and 0x1. That will ensure that those traffic flows will not be affected if some future routing equipment does similar snooping on some future version(s) of IP."

2.1.3. Recommendation

It is RECOMMENDED that where load-balancing of MPLS packets is desired, either an Entropy Label or a FAT Pseudowire Label SHOULD be used; furthermore, the heuristic in Section 2.1.1.1 MUST NOT be used.

A consequence of Recommendation 2 is that, while legacy routers may look for an MFN of 0x4 [RFC0791] or 0x6 [RFC8200], no router will look for a MFN of 0x7 (or whatever the next IP version number will be) for load-balancing purposes. This means that the values 0x4 and 0x6 are used to (sometimes incorrectly) identify IPv4 and IPv6 packets, but no other First Nibble values will be used to identify IP packets.

This obviates the need for paragraph 4, section 3 in [RFC4928]:

"This behavior implies that if in the future an IP version is defined with a version number of 0x0 or 0x1, then equipment complying with this BCP would be unable to look past one or more MPLS headers, and load-split traffic from a single LSP across multiple paths based on a hash of specific fields in the IPv0 or IPv1 headers. That is, IP traffic employing these version numbers would be safe from disturbances caused by inappropriate load-splitting, but would also not be able to get the performance benefits."

This also expands the MFN Registry to all 16 possible values, not just 0x0 and 0x1.

2.1.4. Parsing the Post-stack Header

Given the above recommendations on the use of a PSH and future non-use of the heuristic (Section 2.1.1.1) via the use of Entropy or FAT Pseudowire Labels, the main reason for creating a First Nibble registry is to document the types of PSHs that may follow a label stack, and to simplify their parsing.

2.2. Why Create a Registry

The MPLS WG is currently engaged in updating the MPLS architecture; part of this work may involve the use of PSHs. That might be more challenging if PSH values are allocated on an ad hoc basis, and their parsing and semantics are ill-specified. Consider that the MFN value of 0x0 has two different formats, depending on whether the PSH is a pseudowire control word or a DetNet control word; disambiguation requires the context of the service label. This was a considered decision; documenting this would be helpful to future implementors.

With a registry, PSHs become easier to parse; not needing means outside the data plane to interpret them correctly; and their semantics and usage are documented. (Thank you, IANA!)

2.3. The Relationship between IANA IP Version Numbers and MPLS First Nibble Registries

The use of the MFN stemmed from the desire to heuristically identify IP packets for load-balancing purposes. It was then discovered that non-IP packets, misidentified as IP when the heuristic failed, were being badly load balanced, leading to [RFC4928]. This situation may confuse some as to the relationship between the MPLS First Nibble Registry and the IP Version Numbers registry. These registries are quite different:

  1. The IP Version Numbers registry's explicit purpose is to track IP version numbers in an IP header.
  2. The MPLS First Nibble registry's purpose is to track PSH types.

The only intersection points between the two registries is for values 0x4 and 0x6 (for backward compatibility). There is no need to track future IP version number allocations in the MPLS First Nibble registry.

3. IANA Considerations

3.1. MPLS First Nibble Registry

This memo recommends the creation of an IANA registry called "The MPLS First Nibble Registry" with the following values:

Table 1: MPLS First Nibble Values
Value PSH Type Reference Allocation Policy
0x0 PW Control Word RFC 4385
0x0 DetNet Control Word RFC 8964
0x0 NSH Base Header, Payload RFC 8300
0x1 PW Assoc Channel RFC 4385
0x1 DetNet Assoc Channel draft-ietf-detnet-mpls-oam
0x2 NSH Base Header, OAM RFC 8300
0x3 Unallocated Standards Action
0x4 IPv4 header RFC 791
0x5 BIER header RFC 8296
0x6 IPv6 header RFC 8200
0x7 - 0xE Unallocated Standards Action
0xF Reserved for expansion This document

3.1.1. Allocation Policy

All new values registered here MUST use the Standards Action policy [RFC8126].

4. References

4.1. Normative References

[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC3032]
Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, DOI 10.17487/RFC3032, , <https://www.rfc-editor.org/info/rfc3032>.
[RFC4385]
Bryant, S., Swallow, G., Martini, L., and D. McPherson, "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN", RFC 4385, DOI 10.17487/RFC4385, , <https://www.rfc-editor.org/info/rfc4385>.
[RFC8200]
Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, , <https://www.rfc-editor.org/info/rfc8200>.
[RFC4928]
Swallow, G., Bryant, S., and L. Andersson, "Avoiding Equal Cost Multipath Treatment in MPLS Networks", BCP 128, RFC 4928, DOI 10.17487/RFC4928, , <https://www.rfc-editor.org/info/rfc4928>.
[RFC6790]
Kompella, K., Drake, J., Amante, S., Henderickx, W., and L. Yong, "The Use of Entropy Labels in MPLS Forwarding", RFC 6790, DOI 10.17487/RFC6790, , <https://www.rfc-editor.org/info/rfc6790>.
[RFC8469]
Bryant, S., Malis, A., and I. Bagdonas, "Recommendation to Use the Ethernet Control Word", RFC 8469, DOI 10.17487/RFC8469, , <https://www.rfc-editor.org/info/rfc8469>.
[RFC8300]
Quinn, P., Ed., Elzur, U., Ed., and C. Pignataro, Ed., "Network Service Header (NSH)", RFC 8300, DOI 10.17487/RFC8300, , <https://www.rfc-editor.org/info/rfc8300>.
[RFC8296]
Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A., Tantsura, J., Aldrin, S., and I. Meilik, "Encapsulation for Bit Index Explicit Replication (BIER) in MPLS and Non-MPLS Networks", RFC 8296, DOI 10.17487/RFC8296, , <https://www.rfc-editor.org/info/rfc8296>.
[RFC8126]
Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, , <https://www.rfc-editor.org/info/rfc8126>.
[RFC8964]
Varga, B., Ed., Farkas, J., Berger, L., Malis, A., Bryant, S., and J. Korhonen, "Deterministic Networking (DetNet) Data Plane: MPLS", RFC 8964, DOI 10.17487/RFC8964, , <https://www.rfc-editor.org/info/rfc8964>.
[RFC6391]
Bryant, S., Ed., Filsfils, C., Drafz, U., Kompella, V., Regan, J., and S. Amante, "Flow-Aware Transport of Pseudowires over an MPLS Packet Switched Network", RFC 6391, DOI 10.17487/RFC6391, , <https://www.rfc-editor.org/info/rfc6391>.
[RFC0791]
Postel, J., "Internet Protocol", STD 5, RFC 791, DOI 10.17487/RFC0791, , <https://www.rfc-editor.org/info/rfc791>.

4.2. Informative References

[RFC4364]
Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, , <https://www.rfc-editor.org/info/rfc4364>.
[RFC4761]
Kompella, K., Ed. and Y. Rekhter, Ed., "Virtual Private LAN Service (VPLS) Using BGP for Auto-Discovery and Signaling", RFC 4761, DOI 10.17487/RFC4761, , <https://www.rfc-editor.org/info/rfc4761>.
[RFC7432]
Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A., Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, , <https://www.rfc-editor.org/info/rfc7432>.
[RFC4446]
Martini, L., "IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)", BCP 116, RFC 4446, DOI 10.17487/RFC4446, , <https://www.rfc-editor.org/info/rfc4446>.
[RFC4762]
Lasserre, M., Ed. and V. Kompella, Ed., "Virtual Private LAN Service (VPLS) Using Label Distribution Protocol (LDP) Signaling", RFC 4762, DOI 10.17487/RFC4762, , <https://www.rfc-editor.org/info/rfc4762>.

Authors' Addresses

Kireeti Kompella
Juniper Networks
1133 Innovation Way
Sunnyvale, 94089
United States of America
Stewart Bryant
University of Surrey 5GIC
Matthew Bocci
Nokia
Greg Mirsky (editor)
Ericsson
Loa Andersson
Huawei Technologies
Jie Dong
Huawei Technologies
Huawei Campus, No. 156 Beiqing Rd.
Beijing, 100095
China