Networking Working Group JP. Vasseur, Ed.
Internet-Draft George. Swallow
Intended status: Standards Track Cisco Systems, Inc
Expires: April 1, 2010 Ina. Minei
Juniper Networks
September 28, 2009
Node behavior upon originating and receiving Resource ReserVation
Protocol (RSVP) Path Error message
draft-ietf-mpls-3209-patherr-06.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on April 1, 2010.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Vasseur, et al. Expires April 1, 2010 [Page 1]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
Abstract
The aim of this document is to describe a common practice with regard
to the behavior of a node sending a Resource ReserVation Protocol
(RSVP) Traffic Engineering (TE) Path Error message and to the
behavior of a node receiving an RSVP Path Error message for a
preempted Multi-Protocol Label Switching (MPLS) and Generalized MPLS
(GMPLS) Traffic Engineering Label Switched Path (TE LSP). This
document does not define any new protocol extensions.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Protocol behavior . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Behavior at Detecting Nodes . . . . . . . . . . . . . . . . 4
2.2. Behavior at Receiving Nodes . . . . . . . . . . . . . . . . 4
2.3. Data Plane Behavior . . . . . . . . . . . . . . . . . . . . 5
3. RSVP PathErr Messages For a Preempted TE LSP . . . . . . . . . 5
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 5
5. Security Considerations . . . . . . . . . . . . . . . . . . . . 5
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 6
7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.1. Normative References . . . . . . . . . . . . . . . . . . . 6
7.2. Informative References . . . . . . . . . . . . . . . . . . 6
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 6
Vasseur, et al. Expires April 1, 2010 [Page 2]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
1. Introduction
The aim of this document is to describe a common practice with regard
to the behavior of a node sending a Resource ReserVation Protocol
(RSVP) Traffic Engineering (TE) Path Error message and to the
behavior of a node receiving an RSVP Path Error message for a
preempted Multi-Protocol Label Switching (MPLS) and Generalized MPLS
(GMPLS) Traffic Engineering Label Switched Path (TE LSP) (for
reference to the notion of TE LSP preemption see [RFC3209]).
[RFC2205] defines two RSVP error message types: PathErr and ResvErr
that are generated when an error occurs. Path Error Messages
(PathErr) are used to report errors and travel upstream toward the
head-end of the flow. Resv Error messages (ResvErr) travel
downstream toward the tail-end of the flow.
This document describes only PathErr message processing for the
specific case of a preempted Traffic Engineering Label Switched Path
(TE LSP) where the term preemption is defined in [RFC3209].
2. Protocol behavior
PathErr messages are routed hop-by-hop using the path state
established when a Path message is routed through the network from
the head-end to its tail-end.
As stated in [RFC2205], PathErr messages do not modify the state of
any node through which they pass; they are only reported to the head-
end of the TE LSP (Traffic Engineering Label Switched Path).
The format of the PathErr message is defined in Section 3. of
[RFC2205].
The ERROR_SPEC object includes the IP address of the node that
detected the error (Error Node Address), and specifies the error
through two fields. The Error Code field encodes the category of the
error, for example, Policy Control Failure or Unknown object class.
The Error Value field qualifies the error code to indicate the error
with more precision. [RFC3209] extends RSVP as defined in [RFC2205]
for the management of Multi-Protocol Label Switching (MPLS) Traffic
Engineered Label Switched Paths (TE-LSPs). [RFC3209] specifies
several additional conditions that trigger the sending of a RSVP
PathErr message for which new error codes and error values have been
defined that extend the list defined in [RFC2205]. The exact
circumstances under which a TE LSP is preempted and such PathErr
messages are sent are defined in Section 2.2 of [RFC3209] and will
not be repeated here.
Vasseur, et al. Expires April 1, 2010 [Page 3]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
Values for the Error Code and Error Value fields defined in
[RFC2205], [RFC3209], and other documents are maintained in a
registry by the IANA.
The error conditions fall into two categories:
o Fatal errors represent disruptive conditions for a TE LSP,
o Non-fatal errors are non-disruptive conditions which have occurred
for this TE LSP
PathErr messages may be used in two circumstances:
o During TE LSP establishment,
o After a TE LSP has been successfully established.
Nodal behavior is dependent on which combination of the four cases
listed above applies. The following sections describe the expected
behavior at nodes that perform a preemption action for a TE LSP (and
therefore report using error PathErr messages), and at nodes that
receive PathErr messages. This text is a clarification and re-
statement of the procedures set out in [RFC3209] and does not define
any new behavior.
2.1. Behavior at Detecting Nodes
In the case of fatal errors ("Hard Preemption" see section 4.7.3 of
[RFC3209]), the detecting node SHOULD send a PathErr message
reporting the error condition, and clears the corresponding Path and
Resv (control plane) states. A direct implication is that the data
plane resources of such a TE LSP are also released, thus resulting in
traffic disruption. It should be noted, however, that in fatal error
cases, the LSP has usually already failed in the data plane, and
traffic has already been disrupted. When the error arises during LSP
establishment, the implications are different to when it arises on an
active LSP since no traffic flows until the LSP has been fully
established. In the case of non-fatal errors, the detecting node
should send a PathErr message, and must not clear control plane or
data plane state.
2.2. Behavior at Receiving Nodes
Nodes that receive PathErr messages are all of the nodes along the
path of the TE LSP upstream of the node that detected the error.
This includes the head-end node. In accordance with [RFC2205]
Section 3.7.1, a node receiving a PathErr message takes no action
upon it and consequently it must not clear Path or Resv control plane
Vasseur, et al. Expires April 1, 2010 [Page 4]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
or data plane state. This is true regardless of whether the error
condition reported by the PathErr is fatal or non-fatal. RSVP states
should only be affected upon receiving a PathTear or ResvTear
message, or in the event of a Path or Resv state timeout. Further
discussion of the processing of these events is outside the scope of
this document.
Note that [RFC3473] defines a Path_State_Removed flag in the
ERROR_SPEC object carried on a PathErr message. This field may be
set to change the behavior of upstream nodes that receive the PathErr
message. When set, the flag indicates that the message sender has
removed Path state (and any associated Resv and data plane state) for
the TE LSP. The message receiver should do likewise before
forwarding the message, but may retain state and clear the flag
before forwarding the message.
2.3. Data Plane Behavior
Any node clearing either or both the Path or the Resv state of a TE
LSP MUST also free up the data plane resources allocated to the
corresponding TE LSP.
3. RSVP PathErr Messages For a Preempted TE LSP
Two Error-code have been defined to report a preempted TE LSP:
o As defined in [RFC2750]:Error Code=2: "Policy Control Failure",
Error Value=5 "Flow was preempted"
o As defined in [RFC2205], Error Code=12: "Service preempted"
In both cases, these are fatal errors.
4. IANA Considerations
This document does not define any new protocol extensions and thus no
action is requested to IANA.
5. Security Considerations
This document does not define any new procedures, but clarifies those
defined in other documents where security considerations are already
specified in [RFC3209] and [RFC3473]. This document does not raise
specific security issues beyond those of existing MPLS-TE. By
clarifying the procedures, this document reduces the security risk
Vasseur, et al. Expires April 1, 2010 [Page 5]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
introduced by non-conformant implementations. See
[I-D.ietf-mpls-mpls-and-gmpls-security-framework] for further
discussion of MPLS security issues.
6. Acknowledgements
The author would like to thank Carol Iturralde, Ashok Narayanan, Rom
Reuther and Reshad Rahman.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2205] Braden, B., Zhang, L., Berson, S., Herzog, S., and S.
Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
Functional Specification", RFC 2205, September 1997.
[RFC2750] Herzog, S., "RSVP Extensions for Policy Control",
RFC 2750, January 2000.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.
7.2. Informative References
[I-D.ietf-mpls-mpls-and-gmpls-security-framework]
Fang, L. and M. Behringer, "Security Framework for MPLS
and GMPLS Networks",
draft-ietf-mpls-mpls-and-gmpls-security-framework-06 (work
in progress), July 2009.
Vasseur, et al. Expires April 1, 2010 [Page 6]
Internet-Draft draft-ietf-mpls-3209-patherr-06.txt September 2009
Authors' Addresses
JP Vasseur (editor)
Cisco Systems, Inc
1414 Massachusetts Avenue
Boxborough, MA 01719
USA
Email: jpv@cisco.com
George Swallow
Cisco Systems, Inc
1414 Massachusetts Avenue
Boxborough, MA 01719
USA
Email: swallow@cisco.com
Ina Minei
Juniper Networks
1194 North Mathilda Ave.
Sunnyvale, 94089
Email: ina@juniper.net
Vasseur, et al. Expires April 1, 2010 [Page 7]