Internet Engineering Task Force Q. Zhao
Internet-Draft Huawei Technology
Intended status: Standards Track L. Fang
Expires: May 24, 2012 C. Zhou
Cisco Systems
L. Li
China Mobile
N. So
Verizon Business
R. Torvi
Juniper Networks
November 21, 2011
LDP Extensions for Multi Topology Routing
draft-ietf-mpls-ldp-multi-topology-02.txt
Abstract
Multi-Topology (MT) routing is supported in IP through extension of
IGP protocols, such as OSPF and IS-IS. It would be advantageous to
extend Multiprotocol Label Switching (MPLS), using Label Distribution
Protocol (LDP), to support multiple topologies. These LDP
extensions, known as Multiple Topology Label Distribution Protocol
(MT LDP), would allow the configuration of multiple topologies within
an MPLS LDP enabled network.
This document describes the protocol extensions required to extend
the existing MPLS LDP signalling protocol for creating and
maintaining LSPs in an MT environment.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
Zhao, et al. Expires May 24, 2012 [Page 1]
Internet-Draft LDP Multi Topology Extension November 2011
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 24, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Zhao, et al. Expires May 24, 2012 [Page 2]
Internet-Draft LDP Multi Topology Extension November 2011
Table of Contents
1. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1. Application Scenarios . . . . . . . . . . . . . . . . . . 6
3.1.1. Simplified Data-plane . . . . . . . . . . . . . . . . 6
3.1.2. Using MT for p2p Protection . . . . . . . . . . . . . 6
3.1.3. Using MT for mLDP Protection . . . . . . . . . . . . . 7
3.1.4. Service Separation . . . . . . . . . . . . . . . . . . 7
3.1.5. An Alternative inter-AS VPN Solution . . . . . . . . . 7
3.2. Signaling Extensions . . . . . . . . . . . . . . . . . . . 7
3.2.1. Topology-Scoped Prefix FEC . . . . . . . . . . . . . . 7
3.2.2. LDP MT Capability Advertisement . . . . . . . . . . . 9
3.2.3. Procedures . . . . . . . . . . . . . . . . . . . . . . 11
3.2.4. LDP Sessions . . . . . . . . . . . . . . . . . . . . . 12
3.2.5. Reserved MT ID Values . . . . . . . . . . . . . . . . 12
3.3. MT Applicability on FEC-based features . . . . . . . . . . 13
3.3.1. Typed Wildcard Prefix FEC Element . . . . . . . . . . 13
3.3.2. End-of-LIB . . . . . . . . . . . . . . . . . . . . . . 13
3.4. MPLS Forwarding in MT . . . . . . . . . . . . . . . . . . 14
3.5. Security Consideration . . . . . . . . . . . . . . . . . . 14
3.6. IANA Considerations . . . . . . . . . . . . . . . . . . . 14
3.7. Acknowledgement . . . . . . . . . . . . . . . . . . . . . 15
4. References . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1. Normative References . . . . . . . . . . . . . . . . . . . 15
4.2. Informative References . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16
Zhao, et al. Expires May 24, 2012 [Page 3]
Internet-Draft LDP Multi Topology Extension November 2011
1. Terminology
Terminology used in this document
MT-ID: A 12 bit value to represent Multi-Topology ID.
Default Topology: A topology that is built using the MT-ID value
0.
MT topology: A topology that is built using the corresponding
MT-ID.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Introduction
There are increasing requirements to support multi-topology in MPLS
network. For example, service providers may want to assign different
level of service(s) to different topologies so that the service
separation can be achieved. It is also possible to have an in-band
management network on top of the original MPLS topology, or maintain
separate routing and MPLS domains for isolated multicast or IPv6
islands within the backbone, or force a subset of an address space to
follow a different MPLS topology for the purpose of security, QoS, or
simplified management and/or operations.
OSPF and IS-IS use MT-ID (Multi-Topology Identifier) to identify
different topologies. For each topology identified by an MT-ID, IGP
computes a separate SPF tree independently to find the best paths to
the IP prefixes associated with this topology.
For IP Prefix FECs that are associated with a specific topology, this
solution utilizes the use of MT-ID of the topology in LDP. Thus the
LSP for the given Prefix FEC may be created and maintained along the
IGP path in this topology if it is needed.
Maintaining multiple MTs for MPLS network in a backwards-compatible
manner requires several extensions to the label signaling encoding
and processing procedures. When a label is associated with an IP
Prefix FEC, the corresponding FEC element includes both the
destination prefix (IP address) and the topology it belongs to.
MT based MPLS in general can be used for a variety of purposes such
Zhao, et al. Expires May 24, 2012 [Page 4]
Internet-Draft LDP Multi Topology Extension November 2011
as service separation by assigning each service or a group of
services to a topology, where the management, QoS, and security of
the service or the group of the services can be simplified and
guaranteed, in-band management network "on top" of the original MPLS
topology, maintain separate routing and MPLS forwarding domains for
isolated multicast or IPv6 islands within the backbone, or force a
subset of an address space to follow a different MPLS topology for
the purpose of security, QoS or simplified management and/or
operations.
One of the use of the MT based MPLS is where one class of data
requires low latency links, for example Voice over IP (VoIP) data.
As a result such data may be sent preferably via physical landlines
rather than, for example, high latency links such as satellite links.
As a result an additional topology is defined as all low latency
links on the network and VoIP data packets are assigned to the
additional topology. Further possible examples are File Transfer
Protocol (FTP) or Simple Mail Transfer Protocol (SMTP) traffic which
can be assigned to additional topology comprising high latency links,
and Internet Protocol version 4 (IPv4) versus Internet Protocol
version 6 (IPv6) traffic which may be assigned to different topology
or data to be distinguished by the Quality of Service (QoS) assigned
to it.
3. Requirements
MPLS-MT may be used for a variety of purposes such as service
separation by assigning each service or a group of services to a
topology, where the management, QoS and security of the service or
the group of the services can be simplified and guaranteed, in-band
management network "on top" of the original MPLS topology, maintain
separate routing and MPLS forwarding domains for isolated multicast
or IPv6 islands within the backbone, or force a subset of an address
space to follow a different MPLS topology for the purpose of
security, QoS or simplified management and/or operations.
The following specific requirements and objectives have been defined
in order to provide the functionality described above, and facilitate
service provider configuration and operation.
o Deployment of MPLS-MT within existing MPLS networks should be
possible, with MPLS-MT non-capable nodes existing with MPLS-MT
capable nodes.
o Minimise configuration and operation complexity of MPLS-MT across
the network.
Zhao, et al. Expires May 24, 2012 [Page 5]
Internet-Draft LDP Multi Topology Extension November 2011
o The MPLS-MT solution SHOULD NOT require data-plane modification.
o The MPLS-MT solution MUST support multiple topologies. Allowing a
an MPLS LSP to be established across a specific, or set of,
multiple topologies.
o Control and filtering of LSPs using explicitly including or
excluding multiple topologies MUST be supported.
o The MPLS-MT solution MUST be capable of supporting QoS mechanisms.
[Editors Note - We expect these base MPLS-MT protocol requirements to
be evolved over the next few versions of this document. Note that
all Editors notes will be deleted before publication of the document]
3.1. Application Scenarios
3.1.1. Simplified Data-plane
IGP-MT requires additional data-plane resources maintain multiple
forwarding for each configured MT. On the other hand, MPLS-MT does
not change the data-plane system architecture, if an IGP-MT is mapped
to an MPLS-MT. In case MPLS-MT, incoming label value itself can
determine an MT, and hence it requires a single NHLFE space. MPLS-MT
requires only MT-RIBs in the control-plane, no need to have MT-FIBs.
Forwarding IP packets over a particular MT requires either
configuration or some external means at every node, to maps an
attribute of incoming IP packet header to IGP-MT, which is additional
overhead for network management. Whereas, MPLS-MT mapping is
required only at the ingress-PE of an MPLS-MT LSP, because of each
node identifies MPLS-MT LSP switching based on incoming label, hence
no additional configuration is required at every node.
3.1.2. Using MT for p2p Protection
We know that [IP-FRR-MT] can be used for configuring alternate path
via backup-mt, such that if primary link fails, then backup-MT can be
used for forwarding. However, such techniques require special
marking of IP packets that needs to be forwarded using backup-MT.
MPLS-LDP-MT procedures simplify the forwarding of the MPLS packets
over backup-MT, as MPLS-LDP-MT procedure distribute separate labels
for each MT. How backup paths are computed depends on the
implementation, and the algorithm. The MPLS-LDP-MT in conjunction
with IGP-MT could be used to separate the primary traffic and backup
traffic. For example, service providers can create a backup MT that
consists of links that are meant only for backup traffic. Service
providers can then establish bypass LSPs, standby LSPs, using backup
MT, thus keeping undeterministic backup traffic away from the primary
Zhao, et al. Expires May 24, 2012 [Page 6]
Internet-Draft LDP Multi Topology Extension November 2011
traffic.
3.1.3. Using MT for mLDP Protection
Fro the P2mP or MP2MP LSPs setup by using mLDP protocol, there is a
need to setup a backup LSP to have an end to end protection for the
priamry LSP in the appplicaitons such IPTV, where the end to end
protection is a must. Since the mLDP lSp is setup following the IGP
routes, the second LSP setup by following the IGP routes can not be
guranteed to have the link and node diversity from the primary LSP.
By using MPLS-LDP-MT, two topology can be configured with complete
link and node diversity, where the primary and secondary LSP can be
set up independantly within each topology. The two LSPs setup by
this mechanism can protect each other end-to-end.
3.1.4. Service Separation
MPLS-MT procedures allow establishing two distinct LSPs for the same
FEC, by advertising separate label mapping for each configured
topology. Service providers can implement CoS using MPLS-MT
procedures without requiring to create separate FEC address for each
class. MPLS-MT can also be used separate multicast and unicast
traffic.
3.1.5. An Alternative inter-AS VPN Solution
When the lsp is crossing multiple domains for the inter-as VPN
scenarios, the LSP setup process can be done by configuring a set of
routers which are in different domains into a new single domain with
a new topology ID using the LDP multiple topology. All the routers
belong this new topology will be used to carry the traffic across
multiple domains and since they are in a single domain with the new
topology ID, so the LDP lsp set up can be done without propagating
VPN routes across AS boundaries.
3.2. Signaling Extensions
3.2.1. Topology-Scoped Prefix FEC
LDP assigns and binds a label to a FEC, where a FEC is a list of one
of more FEC elements. To setup LSPs for unicast IP routing paths,
LDP assigns local labels for IP prefixes, and advertises these labels
to its peers so that an LSP is setup along the routing path. To
setup Multi-Topology LSPs for IP prefixes under a given topology
scope, it is a natural requirement to extend LDP "Prefix" FEC element
to include topology info. This infers that MT-ID becomes an
attribute of Prefix FEC element, and all FEC-Label binding operations
are performed under the context of given topology (MT-ID). Following
Zhao, et al. Expires May 24, 2012 [Page 7]
Internet-Draft LDP Multi Topology Extension November 2011
subsection proposes the extension to bind "Prefix FEC" to a topology.
3.2.1.1. New Address Families: MT IP
LDP base specification [RFC5036] (section 3.4.1) defines the "Prefix"
FEC Element as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix (2) | Address Family | PreLen |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Prefix FEC Element Format [RFC5036]
Where "Prefix" encoding is as defined for given "Address Family", and
whose length (in bits) is specified by the "PreLen" field.
To extend IP address families for MT, we propose two new Address
Families named "MT IP" and "MT IPv6" that can be used to specify IP
prefixes within a topology scope. The format of data associated with
these new Address Family is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (IP) Prefix |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | MT-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: MT IP Address Family Format
Where "(IP) Prefix" is an IPv4 and IPv6 address/prefix for "MT IP"
and "MT IPv6" AF respectively, and the field "MT-ID" corresponds to
16-bit Topology ID for given prefix.
For MT LDP, the "Prefix" FEC element's "Address Family" will be set
to "MT IP" or "MT IPv6", and the FEC element will be encoded as
follows:
Zhao, et al. Expires May 24, 2012 [Page 8]
Internet-Draft LDP Multi Topology Extension November 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix (2) | Address Family (MT IP/MT IPv6)| PreLen |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | MT-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: MT Prefix FEC Element Format
Where 16-bit "MT-ID" field defines the Topology ID, and the
definition and usage of "Prefix" and "PreLen" field is same as
defined for IP/IPv6 AF. The value of MT-ID 0 corresponds to default
topology and MUST be ignored on receipt so as to not cause any
conflict/confusion with existing non-MT procedures.
The proposed "Prefix FEC Element" with "MT IP" Address Family can be
used in any LDP message and procedures that currently specify and
allow the use of "Prefix FEC" element with IP/IPv6 Address Family.
This document does not limit the use of these new AF only to LDP
"Prefix FEC element", and these can be used in other FECs and
signaling as required. For example, mLDP MP FECs, as specified in
[mLDP], can be extended to use these new address families to make MP
FECs to become MT aware.
[Editors Note - RFC[5036] doesn't specify the handling of unknown
Address Family. After we have introduced the two new address family
here, RFC[5036] need to be updated to add the handling procedure for
the unknow address families.
3.2.1.2. IGP MT-ID Mapping and Translation
The non-reserved non-special IGP MT-ID values can be used/carried in
LDP as-is and need no translation. However, there is a need for
translating reserved/special IGP MT-ID values to corresponding LDP
MT-IDs. The corresponding special/reserved LDP MT-ID values are
defined in later section 9.
3.2.2. LDP MT Capability Advertisement
We specify a new LDP capability, named "Multi-Topology (MT)", which
is defined in accordance with LDP Capability definition guidelines
[RFC5561]. The LDP "MT" capability can be advertised by an LDP
speaker to its peers either during the LDP session initialization or
after the LDP session is setup to announce LSR capability to support
Zhao, et al. Expires May 24, 2012 [Page 9]
Internet-Draft LDP Multi Topology Extension November 2011
MTR for given IP address family.
The "MT" capability is specified using "Multi-Topology Capability"
TLV. The "Multi-Topology Capability" TLV format is in accordance
with LDP capability guidelines as defined in [RFC5561]. To be able
to specify IP address family, the capability specific data (i.e.
"Capability Data" field of Capability TLV) is populated using "Typed
Wildcard Prefix FEC Element" as defined in [RFC5918].
The format of "Multi-Topology Capability" TLV is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|U|F| Multi-Topology Cap.(IANA) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|S| Reserved | |
+-+-+-+-+-+-+-+-+ |
~ Typed Wcard Prefix FEC element(s) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Multi-Topology Capability TLV Format
Where:
U- and F-bits: MUST be 1 and 0, respectively, as per Section 3 of LDP
Capabilities [RFC5561].
Multi-Topology Capability: Capability TLV type (IANA assigned)
S-bit: MUST be 1 if used in LDP "Initialization" message. MAY be set
to 0 or 1 in dynamic "Capability" message to advertise or withdraw
the capability respectively.
Typed Wcard Prefix FEC element(s): One or two elements specified as
the "Capability data".
Length: The length (in octets) of TLV. The value of this field MUST
be 6 with one FEC element specification, and 11 for two FEC element
specifications.
The encoding of Typed Wcard Prefix FEC element, as defined in
[RFC5561], is as follows:
Zhao, et al. Expires May 24, 2012 [Page 10]
Internet-Draft LDP Multi Topology Extension November 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Typed Wcard (5)|Type=Prefix (2)| Len = 2 | Address... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...Family |
+-+-+-+-+-+-+-+-+
Figure 5: Typed Wildcard Prefix FEC Element [RFC5561]
Where:
Address Family: MUST be set to "MT IP" or "MT IPv6"
3.2.3. Procedures
To announce its MT capability for given IP address family, an LDP
speaker MAY send "MT Capability" with exactly one Typed Wildcard
Prefix FEC element with corresponding "Address Family" field (i.e.
set to "MT IP" for IPv4 and set to "MT IPv6" for IPv6 address
family). To announce its MT capability for both IPv4 and IPv6
address family, an LDP speaker MAY send "MT Capability" with two
Typed Prefix FEC elements in it, where Address Family is set to "MT
IP" in one element and set to "MT IPv6" in other element.
o The capability for supporting multi-topology in LDP can be
advertised during LDP session initialization stage by including
the LDP MT capability TLV in LDP Initialization message. After
LDP session is established, the MT capability can also be
advertised or withdrawn using Capability message (only if "Dynamic
Announcement" capability [RFC5561] has already been successfully
negotiated).
o If an LSR has not advertised MT capability, its peer must not send
messages that include MT identifier to this LSR.
o If an LSR receives a Label Mapping message with MT parameter from
downstream LSR-D and its upstream LSR-U has not advertised MT
capability, an LSP for the MT will not be established.
o We propose to add a new notification event to signal the upstream
that the downstream is not capable.
o If an LSR is changed from non-MT capable to MT capable, it sets
the S bit in MT capability TLV and advertises via the Capability
message. The existing LSP is treated as LSP for default MT (ID
0).
Zhao, et al. Expires May 24, 2012 [Page 11]
Internet-Draft LDP Multi Topology Extension November 2011
o If an LSR is changed from MT capable to non-MT capable, it may
initiate withdraw of all label mapping for existing LSPs of all
non-default MTs. Alternatively, it may wait until the routing
update to withdraw FEC and release the label mapping for existing
LSPs of specific MT.
o There will be case where IGP is MT capable but MPLS is not and the
handling procedure for this case is TBD.
3.2.4. LDP Sessions
Depending on the number of label spaces supported, if a single global
label space is supported, there will be one session supported for
each pair of peer, even there are multiple topologies supported
between these two peers. If there are different label spaces
supported for different topologies, which means that label spaces
overlap with each other for different MTs, then it is suggested to
establish multiple sessions for multiple topologies between these two
peers. In this case, multiple LSR-IDs need to be allocated
beforehand so that each multiple topology can have its own label
space ID.
[Editors Note - This section requires further discussion]
3.2.5. Reserved MT ID Values
Certain MT topologies are assigned to serve pre-determined purposes:
Default-MT: Default topology. This corresponds to OSPF default IPv4
and IPv6, as well as ISIS default IPv4. A value of 0 is proposed.
ISIS IPv6 MT: ISIS default MT-ID for IPv6.
Wildcard-MT: This corresponds to All-Topologies. A value of 65535
(0xffff) is proposed.
We propose a new IANA registry "LDP Multi-Topology ID Name Space"
under IANA "LDP Parameter" namespace to keep LDP MT-ID reserved
value.
If an LSR receives a FEC element with an "MT-ID" value that is
"Reserved" for future use (and not IANA allocated yet), the LSR must
abort the processing of the FEC element, and SHOULD send a
notification message with status code "Invalid MT-ID" to the sender.
[Editors Note - This section requires further discussion].
Zhao, et al. Expires May 24, 2012 [Page 12]
Internet-Draft LDP Multi Topology Extension November 2011
3.3. MT Applicability on FEC-based features
3.3.1. Typed Wildcard Prefix FEC Element
RFC-5918 extends base LDP and defines Typed Wildcard FEC Element
framework [RFC5918]. Typed Wildcard FEC element can be used in any
LDP message to specify a wildcard operation/action for given type of
FEC.
The MT extensions proposed in document do not require any extension
in procedures for Typed Wildcard Prefix FEC element, and these
procedures apply as-is to MT Prefix wildcarding. The MT extensions,
though, allow use of "MT IP" or "MT IPv6" in the Address Family field
of the Typed Wildcard Prefix FEC element in order to use wildcard
operations in the context of a given topology. The use of MT-scoped
address family also allows us to specify MT-ID in these operations.
This document extends Typed Wildcard Prefix FEC element encoding for
MT is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Typed Wcard (5)|Type=Prefix (2)| Len = 4 | AF = MT IP ..|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|... or MT IPv6 | MT-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Typed Wildcard Prefix FEC Element for MT
The proposed format allows an LSR to perform wildcard FEC operations
under the scope of a topology. If an LSR wishes to perform wildcard
operation that applies to all topologies, it can use "Wildcard
Topology" MT-ID as defined in section 5.4. For instance, upon local
un-configuration of topology "x", an LSR may send wildcard label
withdraw with MT-ID "x" to withdraw all its labels from peer that
were advertised under the scope of topology "x". On the other hand,
upon some global configuration change, an LSR may send wildcard label
withdraw with MT-ID set to "Wildcard Topology" to withdraw all its
labels under all topologies from the peer.
3.3.2. End-of-LIB
[RFC5919] specifies extensions and procedures for an LDP speaker to
signal its convergence for given FEC type towards a peer. The
procedures defined in [RFC5919] apply as-is to MT Prefix FEC element.
This means that an LDP speaker MAY signal its IP convergence using
Zhao, et al. Expires May 24, 2012 [Page 13]
Internet-Draft LDP Multi Topology Extension November 2011
Typed Wildcard Prefix FEC element, and its MT IP convergence per
topology using MT Typed Wildcard Prefix FEC element (as defined in
earlier section).
3.4. MPLS Forwarding in MT
Although forwarding is out of the scope of this draft, we include
some forwarding consideration for informational purpose here.
The specified signaling mechanisms allow all the topologies to share
the platform-specific label space; this is the feature that allows
the existing data plane techniques to be used; and the specified
signaling mechanisms do not provide any way for the data plane to
associate a given packet with a context-specific label space.
3.5. Security Consideration
No specific security issues with the proposed solutions are known.
The proposed extension in this document does not introduce any new
security considerations beyond that already apply to the base LDP
specification [RFC5036] and [RFC5920].
3.6. IANA Considerations
The document introduces following new protocol elements that require
IANA consideration and assignments:
o New LDP Capability TLV: "Multi-Topology Capability" TLV (requested
code point: 0x510 from LDP registry "TLV Type Name Space").
o New Status Code: "Invalid Topology ID" (requested code point: 0x50
from LDP registry "Status Code Name Space") as follows:
Registry:
Range/Value E Description
-------------- --- ------------------------------
0x00000050 0 Invalid MT-ID
Figure 7: Invalid Topology ID
o New address families under IANA registry "Address Family Numbers":
- MT IP: Multi-Topology IP version 4 (requested codepoint: 26)
- MT IPv6: Multi-Topology IP version 6 (requested codepoint: 27)
Figure 8: Address Family Numbers
Zhao, et al. Expires May 24, 2012 [Page 14]
Internet-Draft LDP Multi Topology Extension November 2011
o New registry "LDP Multi-Topology (MT) ID Name Space" under "LDP
Parameter" namespace. The registry is defined as:
Range/Value Name
----------- ------------------------
0 Default Topology (ISIS and OSPF)
1-4095 Unassigned
4096 ISIS IPv6 routing topology (i.e. ISIS MT ID #2)
4097-65534 Reserved (for future allocation)
65535 Wildcard Topology (ISIS or OSPF)
Figure 9: LDP Multi-Topology (MT) ID Name Space
3.7. Acknowledgement
The authors would like to thank Dan Tappan, Nabil Bitar, Huang Xin,
Daniel King and Eric Rosen for their valuable comments on this draft.
4. References
4.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3692] Narten, T., "Assigning Experimental and Testing Numbers
Considered Useful", BCP 82, RFC 3692, January 2004.
[RFC5036] Andersson, L., Minei, I., and B. Thomas, "LDP
Specification", RFC 5036, October 2007.
[RFC5919] Asati, R., Mohapatra, P., Chen, E., and B. Thomas,
"Signaling LDP Label Advertisement Completion", RFC 5919,
August 2010.
[RFC5918] Asati, R., Minei, I., and B. Thomas, "Label Distribution
Protocol (LDP) 'Typed Wildcard' Forward Equivalence Class
(FEC)", RFC 5918, August 2010.
4.2. Informative References
[RFC5920] Fang, L., "Security Framework for MPLS and GMPLS
Networks", RFC 5920, July 2010.
Zhao, et al. Expires May 24, 2012 [Page 15]
Internet-Draft LDP Multi Topology Extension November 2011
Authors' Addresses
Quintin Zhao
Huawei Technology
125 Nagog Technology Park
Acton, MA 01719
US
Email: quintin.zhao@huawei.com
Huaimo Chen
Huawei Technology
125 Nagog Technology Park
Acton, MA 01719
US
Email: huaimochen@huawei.com
Emily Chen
Huawei Technology
No. 5 Street, Shangdi Information, Haidian
Beijing
China
Email: chenying220@huawei.com
Lianyuan Li
China Mobile
53A, Xibianmennei Ave.
Xunwu District, Beijing 01719
China
Email: lilianyuan@chinamobile.com
Chen Li
China Mobile
53A, Xibianmennei Ave.
Xunwu District, Beijing 01719
China
Email: lichenyj@chinamobile.com
Zhao, et al. Expires May 24, 2012 [Page 16]
Internet-Draft LDP Multi Topology Extension November 2011
Lu Huang
China Mobile
53A, Xibianmennei Ave.
Xunwu District, Beijing 01719
China
Email: huanglu@chinamobile.com
Luyuang Fang
Cisco Systems
300 Beaver Brook Road
Boxborough, MA 01719
US
Email: lufang@cisco.com
Chao Zhou
Cisco Systems
300 Beaver Brook Road
Boxborough, MA 01719
US
Email: czhou@cisco.com
Kamran Raza
Cisco Systems
2000 Innovation Drive
Kanata, ON K2K-3E8, MA
Canada
Email: E-mail: skraza@cisco.com
Ning So
Verizon Business
2400 North Glenville Drive
Richardson, TX 75082
USA
Email: Ning.So@verizonbusiness.com
Zhao, et al. Expires May 24, 2012 [Page 17]
Internet-Draft LDP Multi Topology Extension November 2011
Raveendra Torvi
Juniper Networks
10, Technoogy Park Drive
Westford, MA 01886-3140
US
Email: rtorvi@juniper.net
Zhao, et al. Expires May 24, 2012 [Page 18]