Network Working Group K. Kompella (Juniper)
Internet Draft P. Pan (Ciena)
draft-ietf-mpls-lsp-ping-04.txt N. Sheth (Juniper)
Category: Standards Track D. Cooper (Global Crossing)
Expires: April 2003 G. Swallow (Cisco)
S. Wadhwa (Juniper)
R. Bonica (WorldCom)
October 2003
Detecting MPLS Data Plane Failures
*** DRAFT ***
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as ``work in progress.''
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Kompella et al Standards Track [Page 1]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Abstract
This document describes a simple and efficient mechanism that can be
used to detect data plane failures in Multi-Protocol Label Switching
(MPLS) Label Switched Paths (LSPs). There are two parts to this
document: information carried in an MPLS "echo request" and "echo
reply" for the purposes of fault detection and isolation; and
mechanisms for reliably sending the echo reply.
Changes since last revision
(This section to be removed before publication.)
Clarified that an MPLS echo request/reply can be either an IPv4 or an
IPv6 packet.
Expanded on Return Codes (section 3.1).
Expanded and reformatted the section on Downstream Mapping.
Expanded the section on Receiving an MPLS Echo Request
Issues
(This section to be removed before publication.)
Need to fill out Downstream Verification.
Need to address issues with pinging L3VPN FECs.
1. Introduction
This document describes a simple and efficient mechanism that can be
used to detect data plane failures in MPLS LSPs. There are two parts
to this document: information carried in an MPLS "echo request" and
"echo reply"; and mechanisms for transporting the echo reply. The
first part aims at providing enough information to check correct
operation of the data plane, as well as a mechanism to verify the
data plane against the control plane, and thereby localize faults.
The second part suggests two methods of reliable reply channels for
the echo request message, for more robust fault isolation.
An important consideration in this design is that MPLS echo requests
follow the same data path that normal MPLS packets would traverse.
MPLS echo requests are meant primarily to validate the data plane,
Kompella et al Standards Track [Page 2]
Internet Draft Detecting MPLS Data Plane Failures October 2003
and secondarily to verify the data plane against the control plane.
Mechanisms to check the control plane are valuable, but are not
covered in this document.
To avoid potential Denial of Service attacks, it is recommended to
regulate the MPLS ping traffic going to the control plane. A rate
limiter should be applied to the well-known UDP port defined below.
1.1. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [KEYWORDS].
1.2. Structure of this document
The body of this memo contains four main parts: motivation, MPLS echo
request/reply packet format, MPLS ping operation, and a reliable
return path. It is suggested that first-time readers skip the actual
packet formats and read the Theory of Operation first; the document
is structured the way it is to avoid forward references.
The last section (reliable return path for RSVP LSPs) may be removed
in a future revision.
2. Motivation
When an LSP fails to deliver user traffic, the failure cannot always
be detected by the MPLS control plane. There is a need to provide a
tool that would enable users to detect such traffic "black holes" or
misrouting within a reasonable period of time; and a mechanism to
isolate faults.
In this document, we describe a mechanism that accomplishes these
goals. This mechanism is modeled after the ping/traceroute paradigm:
ping (ICMP echo request [ICMP]) is used for connectivity checks, and
traceroute is used for hop-by-hop fault localization as well as path
tracing. This document specifies a "ping mode" and a "traceroute"
mode for testing MPLS LSPs.
The basic idea is to test that packets that belong to a particular
Forwarding Equivalence Class (FEC) actually end their MPLS path on an
LSR that is an egress for that FEC. This document proposes that this
test be carried out by sending a packet (called an "MPLS echo
request") along the same data path as other packets belonging to this
FEC. An MPLS echo request also carries information about the FEC
whose MPLS path is being verified. This echo request is forwarded
Kompella et al Standards Track [Page 3]
Internet Draft Detecting MPLS Data Plane Failures October 2003
just like any other packet belonging to that FEC. In "ping" mode
(basic connectivity check), the packet should reach the end of the
path, at which point it is sent to the control plane of the egress
LSR, which then verifies that it is indeed an egress for the FEC. In
"traceroute" mode (fault isolation), the packet is sent to the
control plane of each transit LSR, which performs various checks that
it is indeed a transit LSR for this path; this LSR also returns
further information that helps check the control plane against the
data plane, i.e., that forwarding matches what the routing protocols
determined as the path.
One way these tools can be used is to periodically ping a FEC to
ensure connectivity. If the ping fails, one can then initiate a
traceroute to determine where the fault lies. One can also
periodically traceroute FECs to verify that forwarding matches the
control plane; however, this places a greater burden on transit LSRs
and thus should be used with caution.
3. Packet Format
An MPLS echo request is a (possibly labelled) IPv4 or IPv6 UDP
packet; the contents of the UDP packet have the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version Number | Must Be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Message Type | Reply mode | Return Code | Return Subcode|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sender's Handle |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Sent (seconds) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Sent (microseconds) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Received (seconds) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Received (microseconds) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLVs ... |
. .
. .
. .
| |
Kompella et al Standards Track [Page 4]
Internet Draft Detecting MPLS Data Plane Failures October 2003
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Version Number is currently 1. (Note: the Version Number is to
be incremented whenever a change is made that affects the ability of
an implementation to correctly parse or process an MPLS echo
request/reply. These changes include any syntactic or semantic
changes made to any of the fixed fields, or to any TLV or sub-TLV
assignment or format that is defined at a certain version number.
The Version Number may not need to be changed if an optional TLV or
sub-TLV is added.)
The Message Type is one of the following:
Value Meaning
----- -------
1 MPLS Echo Request
2 MPLS Echo Reply
The Reply Mode can take one of the following values:
Value Meaning
----- -------
1 Do not reply
2 Reply via an IPv4 UDP packet
3 Reply via an IPv4 UDP packet with Router Alert
4 Reply via application level control channel
An MPLS echo request with "Do not reply" may be used for one-way
connectivity tests; the receiving router may log gaps in the sequence
numbers and/or maintain delay/jitter statistics. An MPLS echo
request would normally have "Reply via an IPv4 UDP packet"; if the
normal IPv4 return path is deemed unreliable, one may use "Reply via
an IPv4 UDP packet with Router Alert" (note that this requires that
all intermediate routers understand and know how to forward MPLS echo
replies).
Any application which supports an IP control channel between its
control entities may set the Reply Mode to 4 to ensure that replies
use that same channel. Further definition of this codepoint is
application specific and thus beyond the scope of this docuemnt.
Return Codes and Subcodes are described in the next section.
The Sender's Handle is filled in by the sender, and returned
unchanged by the receiver in the echo reply (if any). There are no
semantics associated with this handle, although a sender may find
this useful for matching up requests with replies.
Kompella et al Standards Track [Page 5]
Internet Draft Detecting MPLS Data Plane Failures October 2003
The Sequence Number is assigned by the sender of the MPLS echo
request, and can be (for example) used to detect missed replies.
The TimeStamp Sent is the time-of-day (in seconds and microseconds,
wrt the sender's clock) when the MPLS echo request is sent. The
TimeStamp Received in an echo reply is the time-of-day (wrt the
receiver's clock) that the corresponding echo request was received.
TLVs (Type-Length-Value tuples) have the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value |
. .
. .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Types are defined below; Length is the length of the Value field in
octets. The Value field depends on the Type; it is zero padded to
align to a four-octet boundary.
Type # Value Field
------ -----------
1 Target FEC Stack
2 Downstream Mapping
3 Pad
4 Error Code
5 Vendor Enterprise Code
3.1. Return Codes
The Return Code is set to zero by the sender. The receiver can set
it to one of the values listed below. The notation <RSC> refers to
the Return Subcode. This field is filled in with the stack-depth for
those codes which specify that. For all other codes the Return
Subcode MUST be set to zero.
Value Meaning
----- -------
0 No return code or return code contained in the Error
Code TLV
Kompella et al Standards Track [Page 6]
Internet Draft Detecting MPLS Data Plane Failures October 2003
1 Malformed echo request received
2 One or more of the TLVs was not understood
3 Replying router is an egress for the FEC at stack
depth <RSC>
4 Replying router has no mapping for the FEC at stack
depth <RSC>
5 Reserved
6 Reserved
7 Reserved
8 Label switched at stack-depth <RSC>
9 Label switched but no MPLS forwarding at stack-depth
<RSC>
10 Mapping for this FEC is not the given label at stack
depth <RSC>
11 No label entry at stack-depth <RSC>
12 Protocol not associated with interface at FEC stack
depth <RSC>
3.2. Target FEC Stack
A Target FEC Stack is a list of sub-TLVs. The number of elements is
determined by the looking at the sub-TLV length fields.
Sub-Type # Length Value Field
---------- ------ -----------
1 5 LDP IPv4 prefix
2 17 LDP IPv6 prefix
3 20 RSVP IPv4 Session Query
4 56 RSVP IPv6 Session Query
5 Reserved; see Appendix
6 13 VPN IPv4 prefix
7 25 VPN IPv6 prefix
8 14 L2 VPN endpoint
9 10 L2 circuit ID
Other FEC Types will be defined as needed.
Kompella et al Standards Track [Page 7]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Note that this TLV defines a stack of FECs, the first FEC element
corresponding to the top of the label stack, etc.
An MPLS echo request MUST have a Target FEC Stack that describes the
FEC stack being tested. For example, if an LSR X has an LDP mapping
for 192.168.1.1 (say label 1001), then to verify that label 1001 does
indeed reach an egress LSR that announced this prefix via LDP, X can
send an MPLS echo request with a FEC Stack TLV with one FEC in it,
namely of type LDP IPv4 prefix, with prefix 192.168.1.1/32, and send
the echo request with a label of 1001.
Say LSR X wanted to verify that a label stack of <1001, 23456> is the
right label stack to use to reach a VPN IPv4 prefix of 10/8 in VPN
foo. Say further that LSR Y with loopback address 192.168.1.1
announced prefix 10/8 with Route Distinguisher RD-foo-Y (which may in
general be different from the Route Distinguisher that LSR X uses in
its own advertisements for VPN foo), label 23456 and BGP nexthop
192.168.1.1. Finally, suppose that LSR X receives a label binding of
1001 for 192.168.1.1 via LDP. X has two choices in sending an MPLS
echo request: X can send an MPLS echo request with a FEC Stack TLV
with a single FEC of type VPN IPv4 prefix with a prefix of 10/8 and a
Route Distinguisher of RD-foo-Y. Alternatively, X can send a FEC
Stack TLV with two FECs, the first of type LDP IPv4 with a prefix of
192.168.1.1/32 and the second of type of IP VPN with a prefix 10/8
with Route Distinguisher of RD-foo-Y. In either case, the MPLS echo
request would have a label stack of <1001, 23456>. (Note: in this
example, 1001 is the "outer" label and 23456 is the "inner" label.)
3.2.1. LDP IPv4 Prefix
The value consists of four octets of an IPv4 prefix followed by one
octet of prefix length in bits. The IPv4 prefix is in network byte
order. See [LDP] for an example of a Mapping for an IPv4 FEC.
3.2.2. LDP IPv6 Prefix
The value consists of sixteen octets of an IPv6 prefix followed by
one octet of prefix length in bits. The IPv6 prefix is in network
byte order. See [LDP] for an example of a Mapping for an IPv6 FEC.
3.2.3. RSVP IPv4 Session
The value has the format below. The value fields are taken from
[RFC3209, sections 4.6.1.1 and 4.6.2.1].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Kompella et al Standards Track [Page 8]
Internet Draft Detecting MPLS Data Plane Failures October 2003
| IPv4 tunnel end point address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Must Be Zero | Tunnel ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Extended Tunnel ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 tunnel sender address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Must Be Zero | LSP ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.2.4. RSVP IPv6 Session
The value has the format below. The value fields are taken from
[RFC3209, sections 4.6.1.2 and 4.6.2.2].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 tunnel end point address |
| |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Must Be Zero | Tunnel ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Extended Tunnel ID |
| |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 tunnel sender address |
| |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Must Be Zero | LSP ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.2.5. VPN IPv4 Prefix
The value field consists of the Route Distinguisher advertised with
the VPN IPv4 prefix, the IPv4 prefix and a prefix length, as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Route Distinguisher |
Kompella et al Standards Track [Page 9]
Internet Draft Detecting MPLS Data Plane Failures October 2003
| (8 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 prefix |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix Length | Must Be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.2.6. VPN IPv6 Prefix
The value field consists of the Route Distinguisher advertised with
the VPN IPv6 prefix, the IPv6 prefix and a prefix length, as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Route Distinguisher |
| (8 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 prefix |
| |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix Length | Must Be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.2.7. L2 VPN Endpoint
The value field consists of a Route Distinguisher (8 octets), the
sender (of the ping)'s CE ID (2 octets), the receiver's CE ID (2
octets), and an encapsulation type (2 octets), formatted as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Route Distinguisher |
| (8 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sender's CE ID | Receiver's CE ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Encapsulation Type | Must Be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Kompella et al Standards Track [Page 10]
Internet Draft Detecting MPLS Data Plane Failures October 2003
3.2.8. L2 Circuit ID
The value field consists of a remote PE address (the address of the
targetted LDP session), a VC ID and an encapsulation type, as
follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Remote PE Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VC ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Encapsulation Type | Must Be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.3. Downstream Mapping
The Downstream Mapping object is an optional TLV. Only one
Downstream Mapping request may appear in and echo request. The
presence of a Downstream Mapping object is a request that Downstream
Mapping objects be included in the echo reply. If the replying
router is the destination of the FEC, then a Downstream Mapping TLV
SHOULD NOT be included in the echo reply. Otherwise Downstream
Mapping objects SHOULD include a Downstream Mapping object for each
interface over which this FEC could be forwarded.
The Length is 16 + M + 4*N octets, where M is the Multipath Length,
and N is the number of Downstream Labels. The Value field of a
Downstream Mapping has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MTU | Address Type | Resvd (SBZ) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream IP Address (4 or 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream Interface Address (4 or 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Hash Key Type | Depth Limit | Multipath Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. (Multipath Information) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream Label | Protocol |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Kompella et al Standards Track [Page 11]
Internet Draft Detecting MPLS Data Plane Failures October 2003
. .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream Label | Protocol |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Maximum Transmission Unit (MTU)
The MTU is the largest MPLS frame (including label stack) that
fits on the interface to the Downstream LSR.
Address Type
The Address Type indicates if the interface is numbered or
unnumbered and is set to one of the following values:
Type # Address Type
------ ------------
1 IPv4
2 Unnumbered
3 IPv6
The field marked SBZ SHOULD be set to zero when sending and
SHOULD be ignored on receipt.
Downstream IP Address and Downstream Interface Address
If the interface to the downstream LSR is numbered, then the
Address Type MUST be set to IPv4 or IPv6, the Downstream IP
Address MUST be set to either the downstream LSR's Router ID or
the interface address of the downstream LSR, and the Downstream
Interface Address MUST be set to the downstream LSR's interface
address.
If the interface to the downstream LSR is unnumbered, the Address
Type MUST be Unnumbered, the Downstream IP Address MUST be the
downstream LSR's Router ID (4 octets), and the Downstream
Interface Address MUST be set to the index assigned by the
upstream LSR to the interface.
Multipath Length
The length in octets of the Multipath Information.
Downstream Label(s)
The set of labels in the label stack as it would have appeared if
Kompella et al Standards Track [Page 12]
Internet Draft Detecting MPLS Data Plane Failures October 2003
this router were forwarding the packet through this interface.
Any Implicit Null labels are explicitly inluded. Labels are
treated as numbers, i.e. they are right justified in the field.
Protocol
The Protocol is taken from the following table:
Protocol # Signaling Protocol
---------- ------------------
0 Unknown
1 Static
2 BGP
3 LDP
4 RSVP-TE
5 Reserved; see Appendix
The notion of "downstream router" and "downstream interface"
should be explained. Consider an LSR X. If a packet that was
originated with TTL n>1 arrived with outermost label L at LSR X,
X must be able to compute which LSRs could receive the packet if
it was originated with TTL=n+1, over which interface the request
would arrive and what label stack those LSRs would see. (It is
outside the scope of this document to specify how this
computation is done.) The set of these LSRs/interfaces are the
downstream routers/interfaces (and their corresponding labels)
for X with respect to L. Each pair of downstream router and
interface requires a separate Downstream Mapping to be added to
the reply. (Note that there are multiple Downstream Label fields
in each TLV as the incoming label L may be swapped with a label
stack.)
The case where X is the LSR originating the echo request is a
special case. X needs to figure out what LSRs would receive the
MPLS echo request for a given FEC Stack that X originates with
TTL=1.
The set of downstream routers at X may be alternative paths (see
the discussion below on ECMP) or simultaneous paths (e.g., for
MPLS multicast). In the former case, the Multipath sub-field is
used as a hint to the sender as to how it may influence the
choice of these alternatives. The "No of Multipaths" is the
number of IP Address/Next Label fields. The Hash Key Type is
taken from the following table:
Key Type Multipath Information
--- ---------------- ---------------------
0 no multipath (empty; M = 0)
Kompella et al Standards Track [Page 13]
Internet Draft Detecting MPLS Data Plane Failures October 2003
1 label labels
2 IP address IP addresses
3 label range low/high label pairs
4 IP address range low/high address pairs
5 no more labels (empty; M = 0)
6 All IP addresses (empty; M = 0)
7 no match (empty; M = 0)
8 Bit-masked IPv4 IP address prefix and bit mask
address set
9 Bit-masked label set Label prefix and bit mask
Type 0 indicates that all packets will be forwarded out this one
interface.
Types 1, 2, 3, 4, 8 and 9 specify that the supplied Multipath
Information will serve to execise this path.
Types 5 and 6 are TBD.
Type 7 indicates that no matches are possible given the Multipath
Information in the received DS mapping information.
Depth Limit
The Depth Limit is applicable only to a label stack, and is the
maximum number of labels considered in the hash; this SHOULD be
set to zero if unspecified or unlimited.
Multipath Information
The multipath information encodes labels or addresses which will
exercise this path. The multipath informaiton depends on the
hash key type. The contents of the field are shown in the table
above. IP addresses are drawn from the range 127/8. Labels are
treated as numbers, i.e. they are right justified in the field.
Label and Address pairs MUST NOT overlap and MUST be in ascending
sequence.
Hash key 8 allows a denser encoding of IP address. The IPv4
prefix is formatted as a base IPv4 address with the non-prefix
low order bits set to zero. The maximum prefix length is 27.
Following the prefix is a mask of length 2^(32-prefix length)
bits. Each bit set to one represents a valid address. The
address is the base IPv4 address plus the position of the bit in
the mask where the bits are numbered left to right begining with
zero.
Hash key 9 allows a denser encoding of Labels. The label prefix
Kompella et al Standards Track [Page 14]
Internet Draft Detecting MPLS Data Plane Failures October 2003
is formatted as a base label value with the non-prefix low order
bits set to zero. The maximum prefix (including leading zeros
due to encoding) length is 27. Following the prefix is a mask of
length 2^(32-prefix length) bits. Each bit set to one represents
a valid Label. The label is the base label plus the position of
the bit in the mask where the bits are numbered left to right
begining with zero.
If the received DS mapping information is non-null the labels and
IP addresses MUST be picked from the set provided or the Hash Key
Type MUST be set to 7.
For example, suppose LSR X at hop 10 has two downstream LSRs Y
and Z for the FEC in question. X could return Hash Key Type 4,
with low/high IP addresses of 1.1.1.1->1.1.1.255 for downstream
LSR Y and 2.1.1.1->2.1.1.255 for downstream LSR Z. The head end
reflects this information to LSR Y. Y, which has three
downstream LSRs U, V and W, computes that 1.1.1.1->1.1.1.127
would go to U and 1.1.1.128-> 1.1.1.255 would go to V. Y would
then respond with 3 Downstream Mappings: to U, with Hash Key Type
4 (1.1.1.1->1.1.1.127); to V, with Hash Key Type 4
(1.1.1.127->1.1.1.255); and to W, with Hash Key Type 7.
3.4. Pad TLV
The value part of the Pad TLV contains a variable number (>= 1) of
octets. The first octet takes values from the following table; all
the other octets (if any) are ignored. The receiver SHOULD verify
that the TLV is received in its entirety, but otherwise ignores the
contents of this TLV, apart from the first octet.
Value Meaning
----- -------
1 Drop Pad TLV from reply
2 Copy Pad TLV to reply
3-255 Reserved for future use
3.5. Error Code
The Error Code TLV is currently not defined; its purpose is to
provide a mechanism for a more elaborate error reporting structure,
should the reason arise.
Kompella et al Standards Track [Page 15]
Internet Draft Detecting MPLS Data Plane Failures October 2003
3.6. Vendor Enterprise Code
The Length is always 4; the value is the SMI Enterprise code, in
network octet order, of the vendor with a Vendor Private extension to
any of the fields in the fixed part of the message, in which case
this TLV MUST be present. If none of the fields in the fixed part of
the message have vendor private extensions, this TLV is OPTIONAL.
4. Theory of Operation
An MPLS echo request is used to test a particular LSP. The LSP to be
tested is identified by the "FEC Stack"; for example, if the LSP was
set up via LDP, and is to an egress IP address of 10.1.1.1, the FEC
stack contains a single element, namely, an LDP IPv4 prefix sub-TLV
with value 10.1.1.1/32. If the LSP being tested is an RSVP LSP, the
FEC stack consists of a single element that captures the RSVP Session
and Sender Template which uniquely identifies the LSP.
FEC stacks can be more complex. For example, one may wish to test a
VPN IPv4 prefix of 10.1/8 that is tunneled over an LDP LSP with
egress 10.10.1.1. The FEC stack would then contain two sub-TLVs, the
first being a VPN IPv4 prefix, and the second being an LDP IPv4
prefix. If the underlying (LDP) tunnel were not known, or was
considered irrelevant, the FEC stack could be a single element with
just the VPN IPv4 sub-TLV.
When an MPLS echo request is received, the receiver is expected to do
a number of tests that verify that the control plane and data plane
are both healthy (for the FEC stack being pinged), and that the two
planes are in sync.
4.1. Dealing with Equal-Cost Multi-Path (ECMP)
LSPs need not be simple point-to-point tunnels. Frequently, a single
LSP may originate at several ingresses, and terminate at several
egresses; this is very common with LDP LSPs. LSPs for a given FEC
may also have multiple "next hops" at transit LSRs. At an ingress,
there may also be several different LSPs to choose from to get to the
desired endpoint. Finally, LSPs may have backup paths, detour paths
and other alternative paths to take should the primary LSP go down.
To deal with the last two first: it is assumed that the LSR sourcing
MPLS echo requests can force the echo request into any desired LSP,
so choosing among multiple LSPs at the ingress is not an issue. The
problem of probing the various flavors of backup paths that will
typically not be used for forwarding data unless the primary LSP is
down will not be addressed here.
Kompella et al Standards Track [Page 16]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Since the actual LSP and path that a given packet may take may not be
known a priori, it is useful if MPLS echo requests can exercise all
possible paths. This, while desirable, may not be practical, because
the algorithms that a given LSR uses to distribute packets over
alternative paths may be proprietary.
To achieve some degree of coverage of alternate paths, there is a
certain lattitude in choosing the destination IP address and source
UDP port for an MPLS echo request. This is clearly not sufficient;
in the case of traceroute, more lattitude is offered by means of the
"Multipath Exercise" sub-TLV of the Downstream Mapping TLV. This is
used as follows. An ingress LSR periodically sends an MPLS
traceroute message to determine whether there are multipaths for a
given LSP. If so, each hop will provide some information how each of
its downstreams can be exercised. The ingress can then send MPLS
echo requests that exercise these paths. If several transit LSRs
have ECMP, the ingress may attempt to compose these to exercise all
possible paths. However, full coverage may not be possible.
4.2. Sending an MPLS Echo Request
An MPLS echo request is a (possibly) labelled UDP packet. The IP
header is set as follows: the source IP address is a routable address
of the sender; the destination IP address is a (randomly chosen)
address from 127/8; the IP TTL is set to 1. The source UDP port is
chosen by the sender; the destination UDP port is set to 3503
(assigned by IANA for MPLS echo requests). The Router Alert option
is set in the IP header.
If the echo request is labelled, one may (depending on what is being
pinged) set the TTL of the innermost label to 1, to prevent the ping
request going farther than it should. Examples of this include
pinging a VPN IPv4 or IPv6 prefix, an L2 VPN end point or an L2
circuit ID. This can also be accomplished by inserting a router
alert label above this label; however, this may lead to the undesired
side effect that MPLS echo requests take a different data path than
actual data.
In "ping" mode (end-to-end connectivity check), the TTL in the
outermost label is set to 255. In "traceroute" mode (fault isolation
mode), the TTL is set successively to 1, 2, ....
The sender chooses a Sender's Handle, and a Sequence Number. When
sending subsequent MPLS echo requests, the sender SHOULD increment
the sequence number by 1. However, a sender MAY choose to send a
group of echo requests with the same sequence number to improve the
chance of arrival of at least one packet with that sequence number.
Kompella et al Standards Track [Page 17]
Internet Draft Detecting MPLS Data Plane Failures October 2003
The TimeStamp Sent is set to the time-of-day (in seconds and
microseconds) that the echo request is sent. The TimeStamp Received
is set to zero.
An MPLS echo request MUST have a FEC Stack TLV. Also, the Reply Mode
must be set to the desired reply mode; the Return Code and Subcode
are set to zero.
In the "traceroute" mode, the echo request SHOULD contain one or more
Downstream Mapping TLVs. For TTL=1, all the downstream routers (and
corresponding labels) for the sender with respect to the FEC Stack
being pinged SHOULD be sent in the echo request. For n>1, the
Downstream Mapping TLVs from the echo reply for TTL=(n-1) are copied
to the echo request with TTL=n; the sender MAY choose to reduce the
size of a "Downstream Multipath Mapping TLV" when copying into the
next echo request as long as the Hash Key Type matching the label or
IP address used to exercise the current MP is still present.
4.3. Receiving an MPLS Echo Request
An LSR X that receives an MPLS echo request first parses the packet
to ensure that it is a well-formed packet, and that the TLVs that are
not marked "Ignore" are understood. If not, X SHOULD send an MPLS
echo reply with the Return Code set to "Malformed echo request
received" or "TLV not understood" (as appropriate), and the Subcode
set to zero. In the latter case, the misunderstood TLVs (only) are
included in the reply.
If the echo request is good, X notes the interface I over which the
echo was received, and the label stack with which it came. If the
MPLS echo request contained a Downstream Verification object (TBD),
then X must format this information as a Downstream Verification
object and include it in its MPLS echo reply message.
X matches up the labels in the received label stack with the FECs
contained in the FEC stack. The matching is done beginning at the
bottom of both stacks and working up. For reporting purposes the
bottom of stack is consided to be stack-depth of 1. This is to
establish an absolute reference for the case where the stack may have
more labels than are in the FEC stack and the sender of the ping has
not requested that a Downstream Verification TLV be sent. If there
are more FECs than labels, the extra FECs are assumed to correspond
to Implicit Null Labels.
Note: in all the error codes listed in this draft a stack-depth of 0
means "no value specified". This allows compatibility with existing
implementations which do not use the Return Subcode field.
Kompella et al Standards Track [Page 18]
Internet Draft Detecting MPLS Data Plane Failures October 2003
X sets a variable, call it current-stack-depth, to the number of
labels in the received label stack. Processing now continues with
the following steps:
1. Check if there is a FEC corresponding to the current-stack-
depth. If there is, go to step 2. If not, check if the label is
valid on interface I. If it is, continue with step 4. Otherwise
X MUST send an MPLS echo reply with a Return Code 11, "No label
entry at stack-depth" and a Return Subcode set to current-stack-
depth.
2. Check the FEC at the current-stack-depth to determine what
protocol was used to advertise it. If X can determine that no
protocol associated with interface I would have advertised a FEC
of that FEC-Type, X MUST send an MPLS echo reply with a Return
Code 12, "Protocol not associated with interface at FEC stack-
depth" and a Return Subcode set to current-stack-depth.
3. Check that the mapping for the FEC at the current-stack-depth is
the corresponding label.
If no mapping for the FEC exists, X MUST send an MPLS echo reply
with a Return Code 4, "Replying router has no mapping for the FEC
at stack-depth" and a Return Subcode set to current- stack-depth.
If a mapping is found, but the mapping is not the corresponding
label, X MUST send an MPLS echo reply with a Return Code 10,
"Mapping for this FEC is not the given label at stack-depth" and
a Return Subcode set to current-stack-depth.
4. X determines the label operation. If the operation is to pop and
continue processing, X checks the current-stack-depth. If it is
one, X MUST send an MPLS echo reply with a Return Code 3,
"Replying router is an egress for the FEC at stack depth" and a
Return Subcode set to one. Otherwise, X decrements current-
stack-depth and goes back to step 1.
If the label operation is pop and switch based on the popped
label, X then checks if it is valid to forward a labelled packet.
If it is not valid to forward a labelled packet, or the current-
stack-depth is one, X MUST send an MPLS echo reply with a Return
Code 9, "Label switched but no MPLS forwarding at stack-depth"
and a Return Subcode set to current-stack-depth. Otherwise, X
MUST send an MPLS echo reply with a Return Code 8, "Label
switched at stack-depth" and a Return Subcode set to current-
stack-depth.
If the label operation is swap, X MUST send an MPLS echo reply
Kompella et al Standards Track [Page 19]
Internet Draft Detecting MPLS Data Plane Failures October 2003
with a Return Code 8, "Label switched at stack-depth" and a
Return Subcode set to current-stack-depth.
If the MPLS echo request contains a downstream mapping TLV, and the
MPLS echo reply has either a Return Code of 8, or a Return Code of 9
with a Return Subcode of 1 then Downstream mapping TLVs SHOULD be
included for each multipath.
If the echo request has a Reply Mode that wants a reply, X uses the
procedure in the next subsection to send the echo reply.
4.4. Sending an MPLS Echo Reply
An MPLS echo reply is a UDP packet. It MUST ONLY be sent in response
to an MPLS echo request. The source IP address is a routable address
of the replier; the source port is the well-known UDP port for MPLS
ping. The destination IP address and UDP port are copied from the
source IP address and UDP port of the echo request. The IP TTL is
set to 255. If the Reply Mode in the echo request is "Reply via an
IPv4 UDP packet with Router Alert", then the IP header MUST contain
the Router Alert IP option. If the reply is sent over an LSP, the
topmost label MUST in this case be the Router Alert label (1) (see
[LABEL-STACK]).
The format of the echo reply is the same as the echo request. The
Sender's Handle, the Sequence Number and TimeStamp Sent are copied
from the echo request; the TimeStamp Received is set to the time-of-
day that the echo request is received (note that this information is
most useful if the time-of-day clocks on the requestor and the
replier are synchronized). The FEC Stack TLV from the echo request
MAY be copied to the reply.
The replier MUST fill in the Return Code and Subcode, as determined
in the previous subsection.
If the echo request contains a Pad TLV, the replier MUST interpret
the first octet for instructions regarding how to reply.
If the echo request contains a Downstream Mapping TLV, the replier
SHOULD compute its downstream routers and corresponding labels for
the incoming label, and add Downstream Mapping TLVs for each one to
the echo reply it sends back.
Kompella et al Standards Track [Page 20]
Internet Draft Detecting MPLS Data Plane Failures October 2003
4.5. Receiving an MPLS Echo Reply
An LSR X should only receive an MPLS Echo Reply in response to an
MPLS Echo Request that it sent. Thus, on receipt of an MPLS Echo
Reply, X should parse the packet to assure that it is well-formed,
then attempt to match up the Echo Reply with an Echo Request that it
had previously sent, using the destination UDP port and the Sender's
Handle. If no match is found, then X jettisons the Echo Reply;
otherwise, it checks the Sequence Number to see if it matches. Gaps
in the Sequence Number MAY be logged and SHOULD be counted. Once an
Echo Reply is received for a given Sequence Number (for a given UDP
port and Handle), the Sequence Number for subsequent Echo Requests
for that UDP port and Handle SHOULD be incremented.
If the Echo Reply contains Downstream Mappings, and X wishes to
traceroute further, it SHOULD copy the Downstream Mappings into its
next Echo Request (with TTL incremented by one).
4.6. Non-compliant Routers
If the egress for the FEC Stack being pinged does not support MPLS
ping, then no reply will be sent, resulting in possible "false
negatives". If in "traceroute" mode, a transit LSR does not support
MPLS ping, then no reply will be forthcoming from that LSR for some
TTL, say n. The LSR originating the echo request SHOULD try sending
the echo request with TTL=n+1, n+2, ..., n+k in the hope that some
transit LSR further downstream may support MPLS echo requests and
reply. In such a case, the echo request for TTL>n MUST NOT have
Downstream Mapping TLVs, until a reply is received with a Downstream
Mapping.
Normative References
[KEYWORDS] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[LABEL-STACK] Rosen, E., et al, "MPLS Label Stack Encoding", RFC
3032, January 2001.
[RSVP] Braden, R. (Editor), et al, "Resource ReSerVation protocol
(RSVP) -- Version 1 Functional Specification," RFC 2205,
September 1997.
[RSVP-REFRESH] Berger, L., et al, "RSVP Refresh Overhead Reduction
Extensions", RFC 2961, April 2001.
[RSVP-TE] Awduche, D., et al, "RSVP-TE: Extensions to RSVP for LSP
Kompella et al Standards Track [Page 21]
Internet Draft Detecting MPLS Data Plane Failures October 2003
tunnels", RFC 3209, December 2001.
Informative References
[ICMP] Postel, J., "Internet Control Message Protocol", RFC 792.
[LDP] Andersson, L., et al, "LDP Specification", RFC 3036, January
2001.
Security Considerations
There are at least two approaches to attacking LSRs using the
mechanisms defined here. One is a Denial of Service attack, by
sending MPLS echo requests/replies to LSRs and thereby increasing
their workload. The other is obfuscating the state of the MPLS data
plane liveness by spoofing, hijacking, replaying or otherwise
tampering with MPLS echo requests and replies.
Authentication will help reduce the number of seemingly valid MPLS
echo requests, and thus cut down the Denial of Service attacks;
beyond that, each LSR must protect itself.
Authentication sufficiently addresses spoofing, replay and most
tampering attacks; one hopes to use some mechanism devised or
suggested by the RPSec WG. It is not clear how to prevent hijacking
(non-delivery) of echo requests or replies; however, if these
messages are indeed hijacked, MPLS ping will report that the data
plane isn't working as it should.
It doesn't seem vital (at this point) to secure the data carried in
MPLS echo requests and replies, although knowledge of the state of
the MPLS data plane may be considered confidential by some.
5. IANA Considerations
The TCP and UDP port number 3503 has been allocated by IANA for LSP
echo requests and replies.
The following sections detail the new name spaces to be managed by
IANA. For each of these name spaces, the space is divided into
assignment ranges; the following terms are used in describing the
procedures by which IANA allocates values: "Standards Action" (as
defined in [IANA]); "Expert Review" and "Vendor Private Use".
Values from "Expert Review" ranges MUST be registered with IANA, and
Kompella et al Standards Track [Page 22]
Internet Draft Detecting MPLS Data Plane Failures October 2003
MUST be accompanied by an Experimental RFC that describes the format
and procedures for using the code point.
Values from "Vendor Private" ranges MUST NOT be registered with IANA;
however, the message MUST contain an enterprise code as registered
with the IANA SMI Network Management Private Enterprise Codes. For
each name space that has a Vendor Private range, it must be specified
where exactly the SMI Enterprise Code resides; see below for
examples. In this way, several enterprises (vendors) can use the
same code point without fear of collision.
5.1. Message Types, Reply Modes, Return Codes
It is requested that IANA maintain registries for Message Types,
Reply Modes, Return Codes and Return Subcodes. Each of these can
take values in the range 0-255. Assignments in the range 0-191 are
via Standards Action; assignments in the range 192-251 are made via
Expert Review; values in the range 252-255 are for Vendor Private
Use, and MUST NOT be allocated.
If any of these fields fall in the Vendor Private range, a top-level
Vendor Enterprise Code TLV MUST be present in the message.
5.2. TLVs
It is requested that IANA maintain registries for the Type field of
top-level TLVs as well as for sub-TLVs. The valid range for each of
these is 0-65535. Assignments in the range 0-32767 are made via
Standards Action; assignments in the range 32768-64511 are made via
Expert Review; values in the range 64512-65535 are for Vendor Private
Use, and MUST NOT be allocated.
If a TLV or sub-TLV has a Type that falls in the range for Vendor
Private Use, the Length MUST be at least 4, and the first four octets
MUST be that vendor's SMI Enterprise Code, in network octet order.
The rest of the Value field is private to the vendor.
Kompella et al Standards Track [Page 23]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Acknowledgments
This document is the outcome of many discussions among many people,
that include Manoj Leelanivas, Paul Traina, Yakov Rekhter, Der-Hwa
Gan, Brook Bailey, Eric Rosen and Ina Minei.
The Multipath Information sub-field of the Downstream Mapping TLV was
adapted from text suggested by Curtis Villamizar.
Appendix
This appendix specifies non-normative aspects of detecting MPLS data
plane liveness.
5.1. CR-LDP FEC
This section describes how a CR-LDP FEC can be included in an Echo
Request using the following FEC subtype:
Sub-Type # Length Value Field
---------- ------ -------------
5 6 CR-LDP LSP ID
The value consists of the LSPID of the LSP being pinged. An LSPID is
a four octet IPv4 address (a local address on the ingress LSR, for
example, the Router ID) plus a two octet identifier that is unique
per LSP on a given ingress LSR.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ingress LSR Router ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Must Be Zero | LSP ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
5.2. Downstream Mapping for CR-LDP
If a label in a Downstream Mapping was learned via CR-LDP, the
Protocol field in the Mapping TLV can use the following entry:
Protocol # Signaling Protocol
---------- ------------------
5 CR-LDP
Kompella et al Standards Track [Page 24]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Authors' Addresses
Kireeti Kompella
Nischal Sheth
Juniper Networks
1194 N.Mathilda Ave
Sunnyvale, CA 94089
e-mail: kireeti@juniper.net
e-mail: nsheth@juniper.net
Ping Pan
Ciena
10480 Ridgeview Court
Cupertino, CA 95014
e-mail: ppan@ciena.com
phone: +1 408.366.4700
Dave Cooper
Global Crossing
960 Hamlin Court
Sunnyvale, CA 94089
email: dcooper@gblx.net
phone: +1 916.415.0437
George Swallow
Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
e-mail: swallow@cisco.com
phone: +1 978.497.8143
Sanjay Wadhwa
Juniper Networks
10 Technology Park Drive
Westford, MA 01886-3146
email: swadhwa@unispherenetworks.com
phone: +1 978.589.0697
Ronald P. Bonica
WorldCom
22001 Loudoun County Pkwy
Ashburn, Virginia, 20147
email: ronald.p.bonica@wcom.com
phone: +1 703.886.1681
Kompella et al Standards Track [Page 25]
Internet Draft Detecting MPLS Data Plane Failures October 2003
Intellectual Property Rights Notices
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implmentation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
Kompella et al Standards Track [Page 26]
Internet Draft Detecting MPLS Data Plane Failures October 2003
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Kompella et al Standards Track [Page 27]