Network Working Group Cheenu Srinivasan
Internet Draft Parama Networks, Inc.
Expires: July 2002
Arun Viswanathan
Force10 Networks, Inc.
Thomas D. Nadeau
Cisco Systems, Inc.
January 2002
Multiprotocol Label Switching (MPLS) Traffic Engineering
Management Information Base
draft-ietf-mpls-te-mib-08.txt
Status of this Memo
This document is an Internet-Draft and is in full
conformance with all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet
Engineering Task Force (IETF), its areas, and its working
groups. Note that other groups may also distribute working
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of
six months and may be updated, replaced, or obsoleted by
other documents at any time. It is inappropriate to use
Internet-Drafts as reference material or to cite them other
than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be
accessed at http://www.ietf.org/shadow.html.
Abstract
This memo defines a portion of the Management Information
Base (MIB) for use with network management protocols in
the Internet community. In particular, it describes
managed objects for Multiprotocol Label Switching (MPLS)
based traffic engineering.
Table of Contents
1. Introduction .............................................. 2
2. Terminology ............................................... 2
3. The SNMP Management Framework ............................. 3
Srinivasan et al. Expires July 2002 [Page 1]
Internet Draft MPLS TE MIB January 2002
4. Feature List .............................................. 4
5. Outline ................................................... 4
5.1. Summary of Traffic Engineering MIB ..................... 4
6. Brief Description of MIB Objects .......................... 5
6.1. mplsTunnelTable ........................................ 5
6.2. mplsTunnelResourceTable ................................ 6
6.3. mplsTunnelHopTable ..................................... 6
6.4. mplsTunnelARHopTable ................................... 6
6.5. mplsTunnelCHoptable .................................... 6
6.6. mplsTunnelPerfTable .................................... 6
6.7. mplsTunnelCRLDPResTable ................................ 6
7. Application of the Interface Group to MPLS Tunnels ........ 7
7.1. Support of the MPLS Tunnel Interface by ifTable ........ 7
8. Example of Tunnel Setup ................................... 9
9. The Use of RowPointer ..................................... 10
10. MPLS Traffic Engineering MIB Definitions ................. 11
11. Security Considerations .................................. 60
12. Acknowledgments .......................................... 60
13. References ............................................... 60
14. Authors' Addresses ....................................... 63
15. Full Copyright Statement ................................. 63
1. Introduction
This memo defines a portion of the Management Information
Base (MIB) for use with network management protocols in the
Internet community. In particular, it describes managed
objects for modeling a Multi-Protocol Label Switching
(MPLS) [RFC3031] based traffic engineering. This MIB should
be used in conjunction with the companion document [LSRMIB]
for MPLS based traffic engineering configuration and
management.
2. Terminology
This document uses terminology from the MPLS architecture
document [RFC3031] and MPLS Label Switch Router MIB
[LSRMIB]. Some frequently used terms are described next.
An explicitly routed LSP (ERLSP) is referred to as an MPLS
tunnel. It consists of one in-segment and/or one out-
segment at the ingress/egress LSRs, each segment being
associated with one MPLS interface. These are also
referred to as tunnel segments. Additionally, at an
intermediate LSR, we model a connection as consisting of
one or more in-segments and/or one or more out-segments.
The binding or interconnection between in-segments and out-
Srinivasan et al. Expires July 2002 [Page 2]
Internet Draft MPLS TE MIB January 2002
segments in performed using a cross-connect. These objects
are defined in the MPLS Label Switch Router MIB [LSRMIB].
3. The SNMP Management Framework
The SNMP Management Framework presently consists of five
major components:
- An overall architecture, described in RFC 2571
[RFC2571].
- Mechanisms for describing and naming objects and events
for the purpose of management. The first version of
this Structure of Management Information (SMI) is
called SMIv1 and described in STD 16, RFC 1155
[RFC1155], STD 16, RFC 1212 [RFC1212] and STD 16, RFC
1215 [RFC1215]. The second version, called SMIv2, is
described in STD 58, RFC 2578 [RFC2578], STD 58, RFC
2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
- Message protocols for transferring management
information. The first version of the SNMP message
protocol is called SNMPv1 and described in STD 15, RFC
1157 [RFC1157]. A second version of the SNMP message
protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901
[RFC1901] and RFC 1906 [RFC1906]. The third version of
the message protocol is called SNMPv3 and described in
RFC 1906 [RFC1906], RFC 2572 [RFC2572] and RFC 2574
[RFC2574].
- Protocol operations for accessing management
information. The first set of protocol operations and
associated PDU formats is described in STD 15, RFC 1157
[RFC1157]. A second set of protocol operations and
associated PDU formats is described in RFC 1905
[RFC1905].
- A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism
described in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management
Framework can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information
store, termed the Management Information Base or MIB.
Objects in the MIB are defined using the mechanisms defined
in the SMI.
Srinivasan et al. Expires July 2002 [Page 3]
Internet Draft MPLS TE MIB January 2002
This memo specifies a MIB module that is compliant to the
SMIv2. A MIB conforming to the SMIv1 can be produced
through the appropriate translations. The resulting
translated MIB must be semantically equivalent, except
where objects or events are omitted because no translation
is possible (use of Counter64). Some machine-readable
information in SMIv2 will be converted into textual
descriptions in SMIv1 during the translation process.
However, this loss of machine-readable information is not
considered to change the semantics of the MIB.
4. Feature List
The MPLS traffic engineering MIB is designed to satisfy the
following requirements and constraints.
- The MIB supports configuration of point-to-point
unidirectional tunnels.
- MPLS tunnels need not be interfaces, but it is possible
to configure a tunnel as an interface.
- The MIB supports manually configured MPLS tunnels as
well as those set up via an MPLS signaling protocol.
- The MIB supports persistent as well as non-persistent
tunnels.
5. Outline
Traffic engineering support for MPLS tunnels requires the
following configuration.
- Setting up MPLS tunnels along with appropriate
configuration parameters.
- Configuring tunnel loose and strict source routed hops.
These actions may need to be accompanied with corresponding
actions using [LSRMIB] to establish and configure tunnel
segments, if this is done manually. Also, the in-segment
and out-segment performance tables, mplsInSegmentPerfTable
and mplsOutSegmentPerfTable [LSRMIB], should be used to
determine performance of the tunnels and tunnel segments.
5.1. Summary of Traffic Engineering MIB
Srinivasan et al. Expires July 2002 [Page 4]
Internet Draft MPLS TE MIB January 2002
The MIB objects for performing these actions consist of the
following tables.
- Tunnel table (mplsTunnelTable) for setting up MPLS
tunnels.
- Resource table (mplsTunnelResourceTable) for setting up
the tunnel resources.
- Tunnel specified, actual, and computed hop tables
(mplsTunnelHopTable, mplsTunnelARHopTable, and
mplsTunnelCHopTable) for strict and loose source routed
MPLS tunnel hops.
- CRLDP resource table (mplsTunnelCRLDPResTable) for
specifying resource objects applicable to tunnels
signaled using CRLDP.
These tables are described in the subsequent sections.
6. Brief Description of MIB Objects
The objects described in this section support the
functionality described in documents [RSVPTE] and [CRLDP].
The tables support both manually configured and signaled
tunnels.
6.1. mplsTunnelTable
The mplsTunnelTable allows new MPLS tunnels to be created
between an MPLS LSR and a remote endpoint, and existing
tunnels to be reconfigured or removed. Note that we only
support point-to-point tunnel segments, although multi-
point-to-point and point-to-multi-point connections are
supported by an LSR acting as a cross-connect. Each MPLS
tunnel can thus have one out-segment originating at an LSR
and/or one in-segment terminating at that LSR.
mplsTunnelTable does not define the in and out segments
forming the tunnel. Instead, these are defined by creating
rows in the in-segment and out-segment tables, defining
relationships in the cross-connect table and referring to
these rows in the mplsTunnelTable using a cross-connect
index, mplsTunnelXCIndex. These segment and cross-connect
related objects are defined in [LSRMIB].
Srinivasan et al. Expires July 2002 [Page 5]
Internet Draft MPLS TE MIB January 2002
6.2. mplsTunnelResourceTable
mplsTunnelResourceTable is used to indicate the resources
required for a tunnel. Multiple tunnels may share the same
resources by pointing to the same entry in this table.
Tunnels that do not share resources must point to separate
entries in this table.
6.3. mplsTunnelHopTable
mplsTunnelHopTable is used to indicate the hops, strict or
loose, for an MPLS tunnel defined in mplsTunnelTable, when
it is established via signaling. Multiple tunnels may
share the same hops by pointing to the same entry in this
table. Each row also has a secondary index,
mplsTunnelHopIndex, corresponding to the next hop of this
tunnel. The scalar mplsTunnelMaxHops indicates the maximum
number of hops that can be specified on each tunnel
supported by this LSR.
6.4. mplsTunnelARHopTable
mplsTunnelARHopTable is used to indicate the actual hops
traversed by a tunnel as reported by the MPLS signaling
protocol after the tunnel is setup. The support of this
table is optional since not all MPLS signaling protocol may
support this feature.
6.5. mplsTunnelCHoptable
mplsTunnelCHopTable lists the actual hops computed by a
constraint-based routing algorithm based on the
mplsTunnelHopTable. The support of this table is optional
since not all implementations may support computation of
hop list using a constraint-based routing protocol.
6.6. mplsTunnelPerfTable
mplsTunnelPerfTable provides several counters to measure
the performance of the MPLS tunnels. This table augments
mplsTunnelTable.
6.7. mplsTunnelCRLDPResTable
mplsTunnelCRLDPResTable contains resource information for
Srinivasan et al. Expires July 2002 [Page 6]
Internet Draft MPLS TE MIB January 2002
those tunnels that are signaled using CRLDP [CRLDP]. This
is a sparse extension to mplsTunnelResourceTable and is
also indexed by mplsTunnelResourceIndex. As with
mplsTunnelResourceTable, multiple tunnels may share the
same resources by pointing to the same entry in this table.
Tunnels that do not share resources must point to separate
entries in this table.
7. Application of the Interface Group to MPLS Tunnels
The Interfaces Group of MIB II defines generic managed
objects for managing interfaces. This memo contains the
media-specific extensions to the Interfaces Group for
managing MPLS Tunnels as logical interfaces.
This memo assumes the interpretation of the Interfaces
Group to be in accordance with [RFC2863] which states that
the interfaces table (ifTable) contains information on the
managed resource's interfaces and that each sub-layer below
the internetwork layer of a network interface is considered
an interface. Thus, the MPLS interface is represented as
an entry in the ifTable. The interrelation of entries in
the ifTable is defined by the Interfaces Stack Group
defined in [RFC2863].
When using MPLS Tunnels as interfaces, the interface stack
table might appear as follows:
+------------------------------------------------+
| MPLS tunnel interface ifType = mplsTunnel(150) |
+------------------------------------------------+
| MPLS interface ifType = mpls(166) |
+------------------------------------------------+
| Underlying layer |
+------------------------------------------------+
In the above diagram, "Underlying Layer" refers to the
ifIndex of any interface type, which has been defined for
MPLS interworking. Examples include ATM, Frame Relay, and
Ethernet.
7.1. Support of the MPLS Tunnel Interface by ifTable
Some specific interpretations of ifTable for those MPLS
tunnels represented as interfaces follow:
Object Use for the MPLS tunnel.
Srinivasan et al. Expires July 2002 [Page 7]
Internet Draft MPLS TE MIB January 2002
ifIndex Each MPLS tunnel is represented by an
ifEntry.
ifDescr Description of the MPLS tunnel.
ifType The value that is allocated for MPLS
tunnel is 150.
ifSpeed The total bandwidth in bits per second
for use by the MPLS tunnel.
ifPhysAddress Unused.
ifAdminStatus See [RFC2863].
ifOperStatus Assumes the value down(2) if the MPLS
tunnel is down.
ifLastChange See [RFC2863].
ifInOctets The number of octets received over the
MPLS tunnel.
ifOutOctets The number of octets transmitted over
the MPLS tunnel.
ifInErrors The number of labeled packets dropped
due to uncorrectable errors.
ifInUnknownProtos The number of received packets
discarded during packet header
validation, including packets with
unrecognized label values.
ifOutErrors See [RFC2863].
ifName Textual name (unique on this system) of
the MPLS tunnel or an octet string of
zero length.
ifLinkUpDownTrapEnable
Default is disabled (2).
ifConnectorPresent Set to false (2).
ifHighSpeed See [RFC2863].
ifHCInOctets The 64-bit version of ifInOctets;
supported if required by the compliance
Srinivasan et al. Expires July 2002 [Page 8]
Internet Draft MPLS TE MIB January 2002
statements in [RFC2863].
ifHCOutOctets The 64-bit version of ifOutOctets;
supported if required by the compliance
statements in [RFC2863].
ifAlias The non-volatile 'alias' name for the
MPLS tunnel as specified by a network
manager.
8. Example of Tunnel Setup
This section contains an example of which MIB objects
should be modified if one would like to create a best
effort, loosely routed, unidirectional traffic engineered
tunnel, which spans two hops of a simple network. Note
that these objects should be created on the "head-end"
LSR.
In mplsTunnelTable:
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 1,
mplsTunnelIngressLSRId = 123.123.125.1,
mplsTunnelEgressLSRId = 123.123.126.1,
mplsTunnelName = "My first tunnel",
mplsTunnelDescr = "Here to there",
mplsTunnelIsIf = true (1),
mplsTunnelXCPointer = mplsXCIndex.2.0.0.15,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = 0,
mplsTunnelOwner = snmp (1),
mplsTunnelLocalProtectInUse = false (0),
mplsTunnelResourcePointer = mplsTunnelResourceIndex.5,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelPrimaryInstance = 0,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAllAffinity = 0,
mplsTunnelPathInUse = 1,
mplsTunnelRole = head (1),
mplsTunnelRowStatus = createAndGo (4)
}
In mplsTunnelResourceTable:
{
Srinivasan et al. Expires July 2002 [Page 9]
Internet Draft MPLS TE MIB January 2002
mplsTunnelResourceIndex = 5,
mplsTunnelResourceMaxRate = 0,
mplsTunnelResourceMeanRate = 0,
mplsTunnelResourceMaxBurstSize = 0,
mplsTunnelResourceRowStatus = createAndGo (4)
}
The next two instances of mplsTunnelHopEntry are used to
denote the hops this tunnel will take across the network.
The following denotes the beginning of the network, or the
first hop. We have used the fictitious LSR identified by
"123.123.125.1" as our example head-end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 1,
mplsTunnelHopAddrType = 1,
mplsTunnelHopIpv4Addr = 123.123.125.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = loose (2),
mplsTunnelHopRowStatus = createAndGo (4)
}
The following denotes the end of the network, or the last
hop in our example. We have used the fictitious LSR
identified by "123.123.126.1" as our end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 2,
mplsTunnelHopAddrType = 1,
mplsTunnelHopIpv4Addr = 123.123.126.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = loose (2),
mplsTunnelHopRowStatus = createAndGo (4)
}
9. The Use of RowPointer
RowPointer is a textual convention used to identify a
conceptual row in an SNMP Table by pointing to one of its
objects. In this MIB, in mplsTunnelTable, the objects
mplsTunnelXCPointer and mplsTunnelResourcePointer are of
type RowPointer. The object mplsTunnelXCPointer points to
Srinivasan et al. Expires July 2002 [Page 10]
Internet Draft MPLS TE MIB January 2002
a specific entry in the mplsXCTable [LSRMIB]. This entry
in the mplsXCTable is the associated LSP for the given MPLS
tunnel entry. The object mplsTunnelResourcePointer points
to a specific entry in a traffic parameter table. An
example of such a traffic parameter table is
mplsTunnelResourceTable. It indicates a specific instance
of a traffic parameter entry that is associated with a
given MPLS tunnel entry.
10. MPLS Traffic Engineering MIB Definitions
MPLS-TE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Integer32, Unsigned32, Counter32, Counter64, TimeTicks
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue, RowStatus, RowPointer, StorageType,
DisplayString, TimeStamp
FROM SNMPv2-TC
InterfaceIndexOrZero
FROM IF-MIB
mplsMIB, MplsBitRate, MplsBurstSize, MplsLSPID,
MplsTunnelIndex, MplsTunnelInstanceIndex,
MplsTunnelAffinity, MplsLsrIdentifier, MplsPathIndex,
MplsPathIndexOrZero
FROM MPLS-TC-MIB
InetAddressIPv4, InetAddressIPv6
FROM INET-ADDRESS-MIB
;
mplsTeMIB MODULE-IDENTITY
LAST-UPDATED
"200201041200Z" -- 4 January 2002 12:00:00 GMT
ORGANIZATION
"Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Cheenu Srinivasan
Postal: Parama Networks, Inc.
1030 Broad Street
Shrewsbury, NJ 07702
Tel: +1-732-544-9120 x731
Email: cheenu@paramanet.com
Arun Viswanathan
Postal: Force10 Networks, Inc.
Srinivasan et al. Expires July 2002 [Page 11]
Internet Draft MPLS TE MIB January 2002
1440 McCarthy Blvd
Milpitas, CA 95035
Tel: +1-408-571-3516
Email: arun@force10networks.com
Thomas D. Nadeau
Postal: Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
Tel: +1-978-244-3051
Email: tnadeau@cisco.com
"
DESCRIPTION
"This MIB module contains managed object definitions
for MPLS Traffic Engineering (TE) as defined in:
1. Extensions to RSVP for LSP Tunnels, Awduche et
al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001
3. Requirements for Traffic Engineering Over MPLS,
Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M.,
and J. McManus, RFC 2702, September 1999"
-- Revision history.
REVISION
"200201041200Z" -- 4 January 2002 12:00:00 GMT
DESCRIPTION
"Initial draft version issues as part of RFC XXXX."
::= { mplsMIB 3 }
-- Top level components of this MIB.
-- tables, scalars
mplsTeScalars OBJECT IDENTIFIER ::= { mplsTeMIB 1 }
mplsTeObjects OBJECT IDENTIFIER ::= { mplsTeMIB 2 }
-- traps
mplsTeNotifications OBJECT IDENTIFIER ::= { mplsTeMIB 3 }
mplsTeNotifyPrefix OBJECT IDENTIFIER ::= { mplsTeNotifications 0 }
-- conformance
mplsTeConformance OBJECT IDENTIFIER ::= { mplsTeMIB 4 }
-- MPLS Tunnel scalars.
Srinivasan et al. Expires July 2002 [Page 12]
Internet Draft MPLS TE MIB January 2002
mplsTunnelConfigured OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of tunnels configured on this device. A
tunnel is considered configured if the
mplsTunnelRowStatus is active(1)."
::= { mplsTeScalars 1 }
mplsTunnelActive OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of tunnels active on this device. A
tunnel is considered active if the
mplsTunnelOperStatus is up(1)."
::= { mplsTeScalars 2 }
mplsTunnelTEDistProto OBJECT-TYPE
SYNTAX BITS {
other (0),
ospf (1),
isis (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The traffic engineering distribution protocol(s)
used by this LSR. Note that an LSR may support more
than one distribution protocol simultaneously."
::= { mplsTeScalars 3 }
mplsTunnelMaxHops OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of hops that can be specified for
a tunnel on this device."
::= { mplsTeScalars 4 }
-- End of MPLS Tunnel scalars.
-- MPLS tunnel table.
mplsTunnelIndexNext OBJECT-TYPE
Srinivasan et al. Expires July 2002 [Page 13]
Internet Draft MPLS TE MIB January 2002
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the next appropriate value to
be used for mplsTunnelIndex when creating entries
in mplsTunnelTable. If the number of unassigned
entries is exhausted, a retrival operation will
return a value of 0. This object may also return a
value of 0 when the LSR is unable to accept
conceptual row creation, for example, if the
mplsTunnelTable is implemented as read-only. To
obtain the value of mplsTunnelIndex for a new
entry, the manager must first issue a management
protocol retrieval operation to obtain the current
value of this object. The agent should modify the
value to reflect the next unassigned index after
each retrieval operation. After a manager retrieves
a value the agent will determine through its local
policy when this index value will be made available
for reuse."
::= { mplsTeObjects 1 }
mplsTunnelTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelTable allows new MPLS tunnels to be
created between an LSR and a remote endpoint, and
existing tunnels to be reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and point-
to-multi-point connections are supported by an LSR
acting as a cross-connect. Each MPLS tunnel can
thus have one out-segment originating at this LSR
and/or one in-segment terminating at this LSR."
::= { mplsTeObjects 2 }
mplsTunnelEntry OBJECT-TYPE
SYNTAX MplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol. Whenever a new entry is created
with mplsTunnelIsIf set to true(1), then a
corresponding entry is created in ifTable as well
Srinivasan et al. Expires July 2002 [Page 14]
Internet Draft MPLS TE MIB January 2002
(see RFC 2863). The ifType of this entry is
mplsTunnel(150)."
REFERENCE
"1. RFC 2863 - The Interfaces Group MIB, McCloghrie,
K., and F. Kastenholtz, June 2000
2. RFC 1700 - Assigned Numbers, Reynolds, J. and J.
Postel, Oct. 1994"
INDEX {
mplsTunnelIndex,
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}
::= { mplsTunnelTable 1 }
MplsTunnelEntry ::= SEQUENCE {
mplsTunnelIndex MplsTunnelIndex,
mplsTunnelInstance MplsTunnelInstanceIndex,
mplsTunnelIngressLSRId MplsLsrIdentifier,
mplsTunnelEgressLSRId MplsLsrIdentifier,
mplsTunnelName DisplayString,
mplsTunnelDescr DisplayString,
mplsTunnelIsIf TruthValue,
mplsTunnelIfIndex InterfaceIndexOrZero,
mplsTunnelXCPointer RowPointer,
mplsTunnelSignallingProto INTEGER,
mplsTunnelSetupPrio INTEGER,
mplsTunnelHoldingPrio INTEGER,
mplsTunnelSessionAttributes BITS,
mplsTunnelOwner INTEGER,
mplsTunnelLocalProtectInUse TruthValue,
mplsTunnelResourcePointer RowPointer,
mplsTunnelInstancePriority Unsigned32,
mplsTunnelHopTableIndex MplsPathIndexOrZero,
mplsTunnelARHopTableIndex MplsPathIndexOrZero,
mplsTunnelCHopTableIndex MplsPathIndexOrZero,
mplsTunnelPrimaryInstance MplsTunnelInstanceIndex,
mplsTunnelPrimaryTimeUp TimeTicks,
mplsTunnelPathChanges Counter32,
mplsTunnelLastPathChange TimeTicks,
mplsTunnelCreationTime TimeStamp,
mplsTunnelStateTransitions Counter32,
mplsTunnelIncludeAnyAffinity MplsTunnelAffinity,
mplsTunnelIncludeAllAffinity MplsTunnelAffinity,
mplsTunnelExcludeAllAffinity MplsTunnelAffinity,
mplsTunnelPathInUse MplsPathIndexOrZero,
mplsTunnelRole INTEGER,
mplsTunnelTotalUpTime TimeTicks,
mplsTunnelInstanceUpTime TimeTicks,
mplsTunnelAdminStatus INTEGER,
Srinivasan et al. Expires July 2002 [Page 15]
Internet Draft MPLS TE MIB January 2002
mplsTunnelOperStatus INTEGER,
mplsTunnelRowStatus RowStatus,
mplsTunnelStorageType StorageType
}
mplsTunnelIndex OBJECT-TYPE
SYNTAX MplsTunnelIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies this row."
::= { mplsTunnelEntry 1 }
mplsTunnelInstance OBJECT-TYPE
SYNTAX MplsTunnelInstanceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies an instance of a tunnel. It is
useful to identify multiple instances of tunnels
for the purposes of backup and parallel tunnels."
::= { mplsTunnelEntry 2 }
mplsTunnelIngressLSRId OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The purpose of this object is to uniquely identity a
tunnel within a network. When the MPLS signalling
protoocol is rsvp(2) this value SHOULD mimic the
Extended Tunnel Id field in the SESSION object.
When the MPLS signalling protoocol is crldp(3) this
value SHOULD mimic the Ingress LSR Router ID field
in the LSPID TLV object."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001"
::= { mplsTunnelEntry 3 }
mplsTunnelEgressLSRId OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the egress LSR ID."
::= { mplsTunnelEntry 4 }
Srinivasan et al. Expires July 2002 [Page 16]
Internet Draft MPLS TE MIB January 2002
mplsTunnelName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The canonical name assigned to the tunnel. This name
can be used to refer to the tunnel on the LSR's
console port. If mplsTunnelIsIf is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863."
REFERENCE
"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"
::= { mplsTunnelEntry 5 }
mplsTunnelDescr OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual string containing information about the
tunnel. If there is no description this object
contains a zero length string."
::= { mplsTunnelEntry 6 }
mplsTunnelIsIf OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this tunnel corresponds to an
interface represented in the interfaces group
table. Note that if this variable is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863."
REFERENCE
"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"
DEFVAL { false }
::= { mplsTunnelEntry 7 }
mplsTunnelIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
Srinivasan et al. Expires July 2002 [Page 17]
Internet Draft MPLS TE MIB January 2002
DESCRIPTION
"If mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which corresponds
to an entry in the interfaces table. Otherwise
this variable should contain the value of zero
indicating that a valid ifIndex was not assigned to
this tunnel interface."
REFERENCE
"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"
::= { mplsTunnelEntry 8 }
mplsTunnelXCPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable points to a row in the mplsXCTable.
This table identifies the segments that compose
this tunnel, their characteristics, and
relationships to each other. A value of zeroDotZero
indicates that no LSP has been associated with this
tunnel yet."
REFERENCE
"Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS
Label Switch Router Management Information Base,
Internet Draft <draft-ietf-mpls-lsr-mib-08.txt>,
December 2001."
::= { mplsTunnelEntry 9 }
mplsTunnelSignallingProto OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rsvp(2),
crldp(3),
other(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The signaling protocol, if any, which was used to
setup this tunnel."
DEFVAL { none }
::= { mplsTunnelEntry 10 }
mplsTunnelSetupPrio OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Srinivasan et al. Expires July 2002 [Page 18]
Internet Draft MPLS TE MIB January 2002
"Indicates the setup priority of this tunnel."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001"
::= { mplsTunnelEntry 11 }
mplsTunnelHoldingPrio OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the holding priority for this tunnel."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001"
::= { mplsTunnelEntry 12 }
mplsTunnelSessionAttributes OBJECT-TYPE
SYNTAX BITS {
fastReroute (0),
mergingPermitted (1),
isPersistent (2),
isPinned (3),
recordRoute(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmask indicates optional session values for
this tunnel. The following describes these
bitfields:
fastRerouteThis flag indicates that the any tunnel
hop may choose to reroute this tunnel without
tearing it down. This flag permits transit routers
to use a local repair mechanism which may result in
violation of the explicit routing of this tunnel.
When a fault is detected on an adjacent downstream
link or node, a transit router can reroute traffic
for fast service restoration.
mergingPermitted This flag permits transit routers
to merge this session with other RSVP sessions for
the purpose of reducing resource overhead on
Srinivasan et al. Expires July 2002 [Page 19]
Internet Draft MPLS TE MIB January 2002
downstream transit routers, thereby providing
better network scalability.
isPersistent Indicates whether this tunnel should
be restored automatically after a failure occurs.
isPinned This flag indicates whether the loose-
routed hops of this tunnel are to be pinned.
recordRouteThis flag indicates whether or not the
signaling protocol should remember the tunnel path
after it has been signaled."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."
DEFVAL { 0 }
::= { mplsTunnelEntry 13 }
mplsTunnelOwner OBJECT-TYPE
SYNTAX INTEGER {
admin(1), -- represents all management entities
rsvp(2),
crldp(3),
policyAgent(4),
other(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates which protocol created and is responsible
for managing this tunnel. Values rsvp(2) and
crldp(3) should not be used at the head-end of a
MPLS tunnel."
::= { mplsTunnelEntry 14 }
mplsTunnelLocalProtectInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates that the local repair mechanism is in use
to maintain this tunnel (usually in the face of an
outage of the link it was previously routed over)."
::= { mplsTunnelEntry 15 }
mplsTunnelResourcePointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
Srinivasan et al. Expires July 2002 [Page 20]
Internet Draft MPLS TE MIB January 2002
DESCRIPTION
"This variable represents a pointer to the traffic
parameter specification for this tunnel. This
value may point at an entry in the
mplsTunnelResourceEntry to indicate which
mplsTunnelResourceEntry is to be assigned to this
segment. This value may optionally point at an
externally defined traffic parameter specification
table. A value of zeroDotZero indicates best-
effort treatment. By having the same value of this
object, two or more segments can indicate resource
sharing."
::= { mplsTunnelEntry 16 }
mplsTunnelInstancePriority OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value indicates which priority, in descending
order, with 0 indicating the lowest priority,
within a group of tunnel instances. A group of
tunnel instances is defined as a set of tunnels
with the same mplsTunnelIndex in this table, but
with a different mplsTunnelInstance. Tunnel group
priorities are used to denote the priority at which
a particular tunnel instance will supercede
another. Instances of tunnels containing the same
mplsTunnelInstancePriority will be used for load
sharing."
DEFVAL { 0 }
::= { mplsTunnelEntry 17 }
mplsTunnelHopTableIndex OBJECT-TYPE
SYNTAX MplsPathIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Index into the mplsTunnelHopTable entry that
specifies the explicit route hops for this tunnel."
::= { mplsTunnelEntry 18 }
mplsTunnelARHopTableIndex OBJECT-TYPE
SYNTAX MplsPathIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index into the mplsTunnelARHopTable entry that
specifies the actual hops traversed by the tunnel."
::= { mplsTunnelEntry 19 }
Srinivasan et al. Expires July 2002 [Page 21]
Internet Draft MPLS TE MIB January 2002
mplsTunnelCHopTableIndex OBJECT-TYPE
SYNTAX MplsPathIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index into the mplsTunnelCHopTable entry that
specifies the computed hops traversed by the
tunnel."
::= { mplsTunnelEntry 20 }
mplsTunnelPrimaryInstance OBJECT-TYPE
SYNTAX MplsTunnelInstanceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the instance index of the primary instance
of this tunnel."
::= { mplsTunnelEntry 21 }
mplsTunnelPrimaryTimeUp OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the total time the primary instance of
this tunnel has been active. The primary instance
of this tunnel is defined in
mplsTunnelPrimaryInstance."
::= { mplsTunnelEntry 22 }
mplsTunnelPathChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of times the paths has changed
for this tunnel."
::= { mplsTunnelEntry 23 }
mplsTunnelLastPathChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the time since the last path change for
this tunnel."
::= { mplsTunnelEntry 24 }
mplsTunnelCreationTime OBJECT-TYPE
Srinivasan et al. Expires July 2002 [Page 22]
Internet Draft MPLS TE MIB January 2002
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the value of SysUpTime when the first
instance of this tunnel came into existence."
::= { mplsTunnelEntry 25 }
mplsTunnelStateTransitions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of times the state of this
tunnel instance has changed."
::= { mplsTunnelEntry 26 }
mplsTunnelIncludeAnyAffinity OBJECT-TYPE
SYNTAX MplsTunnelAffinity
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A link satisfies the include-any constraint if and
only if the constraint is zero, or the link and the
constraint have a resource class in common."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."
::= { mplsTunnelEntry 27 }
mplsTunnelIncludeAllAffinity OBJECT-TYPE
SYNTAX MplsTunnelAffinity
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A link satisfies the include-all constraint if and
only if the link contains all of the adminstrative
groups specified in the constraint."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."
::= { mplsTunnelEntry 28 }
mplsTunnelExcludeAllAffinity OBJECT-TYPE
SYNTAX MplsTunnelAffinity
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A link satisfies the exclude-all constraint if and
only if the link contains none of the adminstrative
Srinivasan et al. Expires July 2002 [Page 23]
Internet Draft MPLS TE MIB January 2002
groups specifie in the constraint."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."
::= { mplsTunnelEntry 29 }
mplsTunnelPathInUse OBJECT-TYPE
SYNTAX MplsPathIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value denotes the configured path that was
chosen for this tunnel. This value reflects the
secondary index into mplsTunnelHopTable. This path
may not exactly match the one in
mplsTunnelARHopTable due to the fact that some CSPF
modification may have taken place. See
mplsTunnelARHopTable for the actual path being
taken by the tunnel. A value of zero denotes that
no path is currently in use or available."
::= { mplsTunnelEntry 30 }
mplsTunnelRole OBJECT-TYPE
SYNTAX INTEGER { head(1), transit(2), tail(3) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value signifies the role that this tunnel
entry/instance represents. This value MUST be set
to head(1) at the originating point of the tunnel.
This value MUST be set to transit(2) at transit
points along the tunnel, if transit points are
supported. This value MUST be set to tail(3) at the
terminating point of the tunnel if tunnel tails are
supported."
::= { mplsTunnelEntry 31 }
mplsTunnelTotalUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents the aggregate up time for all
instances of this tunnel, if available. If this
value is unavailable, it MUST return a value of 0."
::= { mplsTunnelEntry 32 }
mplsTunnelInstanceUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-create
Srinivasan et al. Expires July 2002 [Page 24]
Internet Draft MPLS TE MIB January 2002
STATUS current
DESCRIPTION
"This value identifies the total time that this
tunnel instance's operStatus has been Up(1)."
::= { mplsTunnelEntry 33 }
mplsTunnelAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
-- ready to pass packets
up(1),
down(2),
-- in some test mode
testing(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the desired operational status of this
tunnel."
::= { mplsTunnelEntry 34 }
mplsTunnelOperStatus OBJECT-TYPE
SYNTAX INTEGER {
-- ready to pass packets
up(1),
down(2),
-- in some test mode
testing(3),
-- status cannot be determined
unknown(4),
dormant(5),
-- some component is missing
notPresent(6),
-- down due to the state of
-- lower layer interfaces
lowerLayerDown(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the actual operational status of this
tunnel, which is typically but not limited to, a
function of the state of individual segments of
this tunnel."
::= { mplsTunnelEntry 35 }
mplsTunnelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
Srinivasan et al. Expires July 2002 [Page 25]
Internet Draft MPLS TE MIB January 2002
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table."
::= { mplsTunnelEntry 36 }
mplsTunnelStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object."
::= { mplsTunnelEntry 37 }
-- End of mplsTunnelTable
mplsTunnelHopListIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to be used
for mplsTunnelHopListIndex when creating entries in
the mplsTunnelHopTable. If the number of
unassigned entries is exhausted, a retrival
operation will return a value of 0. This object
may also return a value of 0 when the LSR is unable
to accept conceptual row creation, for example, if
the mplsTunnelHopTable is implemented as read-only.
To obtain the value of mplsTunnelHopListIndex for a
new entry in the mplsTunnelHopTable, the manager
issues a management protocol retrieval operation to
obtain the current value of mplsTunnelHopIndex.
After each retrieval operation, the agent should
modify the value to reflect the next unassigned
index. After a manager retrieves a value the agent
will determine through its local policy when this
index value will be made available for reuse."
::= { mplsTeObjects 3 }
mplsTunnelHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelHopTable is used to indicate the hops,
strict or loose, for an MPLS tunnel defined in
mplsTunnelTable, when it is established via
signaling, for the outgoing direction of the
Srinivasan et al. Expires July 2002 [Page 26]
Internet Draft MPLS TE MIB January 2002
tunnel. Each row in this table is indexed by
mplsTunnelHopListIndex. Each row also has a
secondary index mplsTunnelHopIndex corresponding to
the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelHopTable."
::= { mplsTeObjects 4 }
mplsTunnelHopEntry OBJECT-TYPE
SYNTAX MplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol."
INDEX {
mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex,
mplsTunnelHopIndex
}
::= { mplsTunnelHopTable 1 }
MplsTunnelHopEntry ::= SEQUENCE {
mplsTunnelHopListIndex MplsPathIndex,
mplsTunnelHopPathOptionIndex MplsPathIndex,
mplsTunnelHopIndex MplsPathIndex,
mplsTunnelHopAddrType INTEGER,
mplsTunnelHopIpv4Addr InetAddressIPv4,
mplsTunnelHopIpv4PrefixLen Unsigned32,
mplsTunnelHopIpv6Addr InetAddressIPv6,
mplsTunnelHopIpv6PrefixLen Unsigned32,
mplsTunnelHopAsNumber Unsigned32,
mplsTunnelHopLspId MplsLSPID,
mplsTunnelHopType INTEGER,
mplsTunnelHopIncludeExclude INTEGER,
mplsTunnelHopPathOptionName DisplayString,
mplsTunnelHopEntryPathComp INTEGER,
mplsTunnelHopRowStatus RowStatus,
mplsTunnelHopStorageType StorageType
}
mplsTunnelHopListIndex OBJECT-TYPE
SYNTAX MplsPathIndex
Srinivasan et al. Expires July 2002 [Page 27]
Internet Draft MPLS TE MIB January 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index into this table identifying a
particular explicit route object."
::= { mplsTunnelHopEntry 1 }
mplsTunnelHopPathOptionIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Secondary index into this table identifying a
particular group of hops representing a particular
configured path. This is otherwise known as a path
option."
::= { mplsTunnelHopEntry 2 }
mplsTunnelHopIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Secondary index into this table identifying a
particular hop."
::= { mplsTunnelHopEntry 3 }
mplsTunnelHopAddrType OBJECT-TYPE
SYNTAX INTEGER {
ipV4(1),
ipV6(2),
asNumber(3),
lspid(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP."
DEFVAL { ipV4 }
::= { mplsTunnelHopEntry 4 }
mplsTunnelHopIpv4Addr OBJECT-TYPE
SYNTAX InetAddressIPv4
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsTunnelHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
Srinivasan et al. Expires July 2002 [Page 28]
Internet Draft MPLS TE MIB January 2002
hop. If mplsTunnelHopAddrType is set to lspid(4),
then this value will contain the Ingress LSR Router
ID of the Tunnel. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelHopEntry 5 }
mplsTunnelHopIpv4PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsTunnelHopAddrType is ipV4(1), then the prefix
length for this hop's IPv4 address is contained
herein. This object is otherwise insignificant and
should contain a value of 0."
::= { mplsTunnelHopEntry 6 }
mplsTunnelHopIpv6Addr OBJECT-TYPE
SYNTAX InetAddressIPv6
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the mplsTunnelHopAddrType is set to ipV6(2), then
this variable contains the IPv6 address of this
hop. This object is otherwise insignificant and
should contain a value of 0."
::= { mplsTunnelHopEntry 7 }
mplsTunnelHopIpv6PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsTunnelHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelHopEntry 8 }
mplsTunnelHopAsNumber OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsTunnelHopAddrType is set to asNumber(3), then
this value will contain the AS number of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."
::= { mplsTunnelHopEntry 9 }
Srinivasan et al. Expires July 2002 [Page 29]
Internet Draft MPLS TE MIB January 2002
mplsTunnelHopLspId OBJECT-TYPE
SYNTAX MplsLSPID
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsTunnelHopAddrType is set to lspid(4), then
this value will contain the LSPID of a tunnel of
this hop. The present tunnel being configured is
tunneled through this hop (using label stacking).
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."
::= { mplsTunnelHopEntry 10 }
mplsTunnelHopType OBJECT-TYPE
SYNTAX INTEGER {
strict(1),
loose(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether this tunnel hop is routed in a
strict or loose fashion."
::= { mplsTunnelHopEntry 11 }
mplsTunnelHopIncludeExclude OBJECT-TYPE
SYNTAX INTEGER {
include(1),
exclude(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If this value is set to include(1), then this
indicates that this hop must be included in the
tunnel's path. If this value is set to exclude(2),
then this hop must be avoided when calculating the
path for this tunnel. The default value of this
object is include(1), so that by default all
indicated hops are included in the CSPF path
computation."
DEFVAL { include }
::= { mplsTunnelHopEntry 12 }
mplsTunnelHopPathOptionName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The description of this series of hops as they
Srinivasan et al. Expires July 2002 [Page 30]
Internet Draft MPLS TE MIB January 2002
relate to the specified path option."
::= { mplsTunnelHopEntry 13 }
mplsTunnelHopEntryPathComp OBJECT-TYPE
SYNTAX INTEGER {
dynamic(1), -- CSPF computed
explicit(2) -- strict hop
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If this value is set to dynamic, then the user
should only specify the source and destination of
the path and expect that the CSPF will calculate
the remainder of the path. If this value is set to
explicit, the user should specify the entire path
for the tunnel to take. This path may contain
strict or loose hops. Each hop along a specific
path should have this object set to the same value"
::= { mplsTunnelHopEntry 14 }
mplsTunnelHopRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table."
::= { mplsTunnelHopEntry 15 }
mplsTunnelHopStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object."
::= { mplsTunnelHopEntry 16 }
-- End of mplsTunnelHopTable
-- Begin of mplsTunnelResourceTable
mplsTunnelResourceIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0.. 2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the next appropriate value to
be used for mplsTunnelResourceIndex when creating
Srinivasan et al. Expires July 2002 [Page 31]
Internet Draft MPLS TE MIB January 2002
entries in the mplsTunnelResourceTable. If the
number of unassigned entries is exhausted, a
retrival operation will return a value of 0. This
object may also return a value of 0 when the LSR is
unable to accept conceptual row creation, for
example, if the mplsTunnelTable is implemented as
read-only. To obtain the mplsTunnelResourceIndex
value for a new entry, the manager must first issue
a management protocol retrieval operation to obtain
the current value of this object. The agent should
modify the value to reflect the next unassigned
index after each retrieval operation. After a
manager retrieves a value the agent will determine
through its local policy when this index value will
be made available for reuse."
::= { mplsTeObjects 5 }
mplsTunnelResourceTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelResourceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelResourceTable allows a manager to
specify which resources are desired for an MPLS
tunnel. This table also allows several tunnels to
point to a single entry in this table, implying
that these tunnels should share resources."
::= { mplsTeObjects 6 }
mplsTunnelResourceEntry OBJECT-TYPE
SYNTAX MplsTunnelResourceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a set of resources
for an MPLS tunnel. An entry can be created by a
network administrator or by an SNMP agent as
instructed by any MPLS signaling protocol."
INDEX { mplsTunnelResourceIndex }
::= { mplsTunnelResourceTable 1 }
MplsTunnelResourceEntry ::= SEQUENCE {
mplsTunnelResourceIndex Unsigned32,
mplsTunnelResourceMaxRate MplsBitRate,
mplsTunnelResourceMeanRate MplsBitRate,
mplsTunnelResourceMaxBurstSize MplsBurstSize,
mplsTunnelResourceMeanBurstSize MplsBurstSize,
mplsTunnelResourceExcessBurstSize MplsBurstSize,
mplsTunnelResourceFrequency INTEGER,
mplsTunnelResourceWeight Unsigned32,
Srinivasan et al. Expires July 2002 [Page 32]
Internet Draft MPLS TE MIB January 2002
mplsTunnelResourceRowStatus RowStatus,
mplsTunnelResourceStorageType StorageType
}
mplsTunnelResourceIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies this row."
::= { mplsTunnelResourceEntry 1 }
mplsTunnelResourceMaxRate OBJECT-TYPE
SYNTAX MplsBitRate
UNITS "bits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum rate in bits/second. Note that setting
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate, and
mplsTunnelResourceMaxBurstSize to 0 indicates best-
effort treatment.
This object is copied to an instance of
mplsTrafficParamMaxRate in mplsTrafficParamTable
the OID of which is copied into the corresponding
mplsInSegmentTrafficParamPtr."
REFERENCE
"Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS
Label Switch Router Management Information Base,
Internet Draft <draft-ietf-mpls-lsr-mib-08.txt>,
December 2001."
::= { mplsTunnelResourceEntry 2 }
mplsTunnelResourceMeanRate OBJECT-TYPE
SYNTAX MplsBitRate
UNITS "bits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is copied into an instance of
mplsTrafficParamMeanRate in the
mplsTrafficParamTable. The OID of this table entry
is then copied into the corresponding
mplsInSegmentTrafficParamPtr.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry in
mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMeanRate to mplsTrafficParamMeanRate.
Srinivasan et al. Expires July 2002 [Page 33]
Internet Draft MPLS TE MIB January 2002
The OID of this entry is copied to
mplsInSegmentTrafficParamPtr of the corresponding
in-segment entry."
REFERENCE
"Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS
Label Switch Router Management Information Base,
Internet Draft <draft-ietf-mpls-lsr-mib-08.txt>,
December 2001."
::= { mplsTunnelResourceEntry 3 }
mplsTunnelResourceMaxBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum burst size in bytes. This object is
copied to mplsInSegmentMaxBurstSize of the
corresponding in-segment.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry in
mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMaxBurstSize to
mplsTrafficParamMaxBurstSize. The OID of this entry
is copied to mplsInSegmentTrafficParamPtr of the
corresponding in-segment entry."
REFERENCE
"Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS
Label Switch Router Management Information Base,
Internet Draft <draft-ietf-mpls-lsr-mib-08.txt>,
December 2001."
::= { mplsTunnelResourceEntry 4 }
mplsTunnelResourceMeanBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mean burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value."
::= { mplsTunnelResourceEntry 5 }
mplsTunnelResourceExcessBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
Srinivasan et al. Expires July 2002 [Page 34]
Internet Draft MPLS TE MIB January 2002
STATUS current
DESCRIPTION
"The Excess burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value."
REFERENCE
"CR-LDP Specification, Section 4.3."
::= { mplsTunnelResourceEntry 6 }
mplsTunnelResourceFrequency OBJECT-TYPE
SYNTAX INTEGER {
unspecified(1),
frequent(2),
veryFrequent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The granularity of the availability of committed
rate. The implementations which do not implement
this variable must return unspecified(1) for this
value and must not allow a user to set this value."
REFERENCE
"CR-LDP Specification, Section 4.3."
::= { mplsTunnelResourceEntry 7 }
mplsTunnelResourceWeight OBJECT-TYPE
SYNTAX Unsigned32(0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP."
REFERENCE
"CR-LDP Specification, Section 4.3."
::= { mplsTunnelResourceEntry 8 }
mplsTunnelResourceRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table."
::= { mplsTunnelResourceEntry 9 }
mplsTunnelResourceStorageType OBJECT-TYPE
SYNTAX StorageType
Srinivasan et al. Expires July 2002 [Page 35]
Internet Draft MPLS TE MIB January 2002
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object."
::= { mplsTunnelResourceEntry 10 }
-- End mplsTunnelResourceTable
-- Tunnel Actual Route Hop table.
mplsTunnelARHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelARHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as reported by the MPLS
signaling protocol, for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelARHopListIndex. Each row also has a
secondary index mplsTunnelARHopIndex, corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelARHopTable.
Please note that since the information necessary to
build entries within this table are not provided by
some MPLS signaling protocols, implementation of
this table is optional. Furthermore, since the
information in this table is actually provided by
the MPLS signaling protocol after the path has been
set-up, the entries in this table are provided only
for observation, and hence, all variables in this
table are accessible exclusively as read-only."
::= { mplsTeObjects 7 }
mplsTunnelARHopEntry OBJECT-TYPE
SYNTAX MplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a tunnel hop. An
Srinivasan et al. Expires July 2002 [Page 36]
Internet Draft MPLS TE MIB January 2002
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol."
INDEX { mplsTunnelARHopListIndex, mplsTunnelARHopIndex }
::= { mplsTunnelARHopTable 1 }
MplsTunnelARHopEntry ::= SEQUENCE {
mplsTunnelARHopListIndex MplsPathIndex,
mplsTunnelARHopIndex MplsPathIndex,
mplsTunnelARHopAddrType INTEGER,
mplsTunnelARHopIpv4Addr InetAddressIPv4,
mplsTunnelARHopIpv4PrefixLen Unsigned32,
mplsTunnelARHopIpv6Addr InetAddressIPv6,
mplsTunnelARHopIpv6PrefixLen Unsigned32,
mplsTunnelARHopAsNumber Unsigned32,
mplsTunnelARHopLspId MplsLSPID
}
mplsTunnelARHopListIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index into this table identifying a
particular recorded hop list."
::= { mplsTunnelARHopEntry 1 }
mplsTunnelARHopIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Secondary index into this table identifying the
particular hop."
::= { mplsTunnelARHopEntry 2 }
mplsTunnelARHopAddrType OBJECT-TYPE
SYNTAX INTEGER {
ipV4(1),
ipV6(2),
asNumber(3),
lspId(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Denotes the address type of this tunnel hop."
DEFVAL { ipV4 }
::= { mplsTunnelARHopEntry 3 }
Srinivasan et al. Expires July 2002 [Page 37]
Internet Draft MPLS TE MIB January 2002
mplsTunnelARHopIpv4Addr OBJECT-TYPE
SYNTAX InetAddressIPv4
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelARHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0."
::= { mplsTunnelARHopEntry 4 }
mplsTunnelARHopIpv4PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelARHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelARHopEntry 5 }
mplsTunnelARHopIpv6Addr OBJECT-TYPE
SYNTAX InetAddressIPv6
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the mplsTunnelARHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0."
::= { mplsTunnelARHopEntry 6 }
mplsTunnelARHopIpv6PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelARHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelARHopEntry 7 }
mplsTunnelARHopAsNumber OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelARHopAddrType is set to asNumber(3),
Srinivasan et al. Expires July 2002 [Page 38]
Internet Draft MPLS TE MIB January 2002
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact."
::= { mplsTunnelARHopEntry 8 }
mplsTunnelARHopLspId OBJECT-TYPE
SYNTAX MplsLSPID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelARHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."
::= { mplsTunnelARHopEntry 9 }
-- End of mplsTunnelARHopTable
-- Tunnel Computed Hop table.
mplsTunnelCHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelCHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as computed by a constraint-
based routing protocol, based on the
mplsTunnelHopTable for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelCHopListIndex. Each row also has a
secondary index mplsTunnelCHopIndex, corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelCHopTable.
Please note that since the information necessary to
build entries within this table may not be
supported by some LSRs, implementation of this
table is optional. Furthermore, since the
information in this table is actually provided by
routing protocol after the path has been computed,
Srinivasan et al. Expires July 2002 [Page 39]
Internet Draft MPLS TE MIB January 2002
the entries in this table are provided only for
observation, and hence, all variables in this table
are accessible exclusively as read-only."
::= { mplsTeObjects 8 }
mplsTunnelCHopEntry OBJECT-TYPE
SYNTAX MplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a tunnel hop. An
entry in this table is created by a constraint-
based routing protocol based on the hops specified
in the corresponding mplsTunnelHopTable."
INDEX { mplsTunnelCHopListIndex, mplsTunnelCHopIndex }
::= { mplsTunnelCHopTable 1 }
MplsTunnelCHopEntry ::= SEQUENCE {
mplsTunnelCHopListIndex MplsPathIndex,
mplsTunnelCHopIndex MplsPathIndex,
mplsTunnelCHopAddrType INTEGER,
mplsTunnelCHopIpv4Addr InetAddressIPv4,
mplsTunnelCHopIpv4PrefixLen Unsigned32,
mplsTunnelCHopIpv6Addr InetAddressIPv6,
mplsTunnelCHopIpv6PrefixLen Unsigned32,
mplsTunnelCHopAsNumber Unsigned32,
mplsTunnelCHopLspId MplsLSPID,
mplsTunnelCHopType INTEGER
}
mplsTunnelCHopListIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index into this table identifying a
particular computed hop list."
::= { mplsTunnelCHopEntry 1 }
mplsTunnelCHopIndex OBJECT-TYPE
SYNTAX MplsPathIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Secondary index into this table identifying the
particular hop."
::= { mplsTunnelCHopEntry 2 }
mplsTunnelCHopAddrType OBJECT-TYPE
SYNTAX INTEGER {
Srinivasan et al. Expires July 2002 [Page 40]
Internet Draft MPLS TE MIB January 2002
ipV4(1),
ipV6(2),
asNumber(3),
lspId(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Denotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP."
DEFVAL { ipV4 }
::= { mplsTunnelCHopEntry 3 }
mplsTunnelCHopIpv4Addr OBJECT-TYPE
SYNTAX InetAddressIPv4
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelCHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0."
::= { mplsTunnelCHopEntry 4 }
mplsTunnelCHopIpv4PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelCHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelCHopEntry 5 }
mplsTunnelCHopIpv6Addr OBJECT-TYPE
SYNTAX InetAddressIPv6
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the mplsTunnelCHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0."
::= { mplsTunnelCHopEntry 6 }
mplsTunnelCHopIpv6PrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS read-only
Srinivasan et al. Expires July 2002 [Page 41]
Internet Draft MPLS TE MIB January 2002
STATUS current
DESCRIPTION
"If mplsTunnelCHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0."
::= { mplsTunnelCHopEntry 7 }
mplsTunnelCHopAsNumber OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelCHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact."
::= { mplsTunnelCHopEntry 8 }
mplsTunnelCHopLspId OBJECT-TYPE
SYNTAX MplsLSPID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If mplsTunnelCHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."
::= { mplsTunnelCHopEntry 9 }
mplsTunnelCHopType OBJECT-TYPE
SYNTAX INTEGER {
strict(1),
loose(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Denotes whether this is tunnel hop is routed in a
strict or loose fashion."
::= { mplsTunnelCHopEntry 10 }
-- End of mplsTunnelCHopTable
-- MPLS Tunnel Performance Table.
mplsTunnelPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelPerfEntry
MAX-ACCESS not-accessible
Srinivasan et al. Expires July 2002 [Page 42]
Internet Draft MPLS TE MIB January 2002
STATUS current
DESCRIPTION
"This table provides per-tunnel MPLS performance
information."
::= { mplsTeObjects 9 }
mplsTunnelPerfEntry OBJECT-TYPE
SYNTAX MplsTunnelPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for
every tunnel. Its is an extension to
mplsTunnelEntry."
AUGMENTS { mplsTunnelEntry }
::= { mplsTunnelPerfTable 1 }
MplsTunnelPerfEntry ::= SEQUENCE {
mplsTunnelPerfPackets Counter32,
mplsTunnelPerfHCPackets Counter64,
mplsTunnelPerfErrors Counter32,
mplsTunnelPerfBytes Counter32,
mplsTunnelPerfHCBytes Counter64
}
mplsTunnelPerfPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets forwarded by the tunnel."
::= { mplsTunnelPerfEntry 1 }
mplsTunnelPerfHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets
forwarded by the tunnel."
::= { mplsTunnelPerfEntry 2 }
mplsTunnelPerfErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of errored packets."
::= { mplsTunnelPerfEntry 3 }
Srinivasan et al. Expires July 2002 [Page 43]
Internet Draft MPLS TE MIB January 2002
mplsTunnelPerfBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of bytes forwarded by the tunnel."
::= { mplsTunnelPerfEntry 4 }
mplsTunnelPerfHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes forwarded
by the tunnel."
::= { mplsTunnelPerfEntry 5 }
-- End of mplsTunnelPerfTable
-- CR-LDP Tunnel Resource Table
mplsTunnelCRLDPResTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelCRLDPResEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mplsTunnelCRLDPResTable allows a manager to
specify which CR-LDP-specific resources are desired
for an MPLS tunnel if that tunnel is signaled using
CR-LDP. Note that these attributes are in addition
to those specified in mplsTunnelResourceTable. This
table also allows several tunnels to point to a
single entry in this table, implying that these
tunnels should share resources."
::= { mplsTeObjects 10 }
mplsTunnelCRLDPResEntry OBJECT-TYPE
SYNTAX MplsTunnelCRLDPResEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a set of resources
for an MPLS tunnel established using CRLDP
(mplsTunnelSignallingProto equal to crldp (3)). An
entry can be created by a network administrator or
by an SNMP agent as instructed by any MPLS
signaling protocol."
INDEX { mplsTunnelResourceIndex }
::= { mplsTunnelCRLDPResTable 1 }
Srinivasan et al. Expires July 2002 [Page 44]
Internet Draft MPLS TE MIB January 2002
MplsTunnelCRLDPResEntry ::= SEQUENCE {
mplsTunnelCRLDPResMeanBurstSize MplsBurstSize,
mplsTunnelCRLDPResExcessBurstSize MplsBurstSize,
mplsTunnelCRLDPResFrequency Integer32,
mplsTunnelCRLDPResWeight Unsigned32,
mplsTunnelCRLDPResFlags Unsigned32,
mplsTunnelCRLDPResRowStatus RowStatus,
mplsTunnelCRLDPResStorageType StorageType
}
mplsTunnelCRLDPResMeanBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mean burst size in bytes."
::= { mplsTunnelCRLDPResEntry 2 }
mplsTunnelCRLDPResExcessBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Excess burst size in bytes."
REFERENCE
"CR-LDP Specification, Section 4.3."
::= { mplsTunnelCRLDPResEntry 3 }
mplsTunnelCRLDPResFrequency OBJECT-TYPE
SYNTAX INTEGER {
unspecified(1),
frequent(2),
veryFrequent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The granularity of the availability of committed
rate."
REFERENCE
"CR-LDP Specification, Section 4.3."
::= { mplsTunnelCRLDPResEntry 4 }
mplsTunnelCRLDPResWeight OBJECT-TYPE
SYNTAX Unsigned32(0..255)
MAX-ACCESS read-create
STATUS current
Srinivasan et al. Expires July 2002 [Page 45]
Internet Draft MPLS TE MIB January 2002
DESCRIPTION
"The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP."
REFERENCE
"CR-LDP Specification, Section 4.3."
DEFVAL { 0 }
::= { mplsTunnelCRLDPResEntry 5 }
mplsTunnelCRLDPResFlags OBJECT-TYPE
SYNTAX Unsigned32 (0..63)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the 1 byte Flags conveyed as part of
the traffic parameters during the establishment of
the CRLSP. The bits in this object are to be
interpreted as follows.
+--+--+--+--+--+--+--+--+
| Res |F6|F5|F4|F3|F2|F1|
+--+--+--+--+--+--+--+--+
Res - These bits are reserved. Zero on transmission.
Ignored on receipt.
F1 - Corresponds to the PDR.
F2 - Corresponds to the PBS.
F3 - Corresponds to the CDR.
F4 - Corresponds to the CBS.
F5 - Corresponds to the EBS.
F6 - Corresponds to the Weight.
Each flag if is a Negotiable Flag corresponding to a
Traffic Parameter. The Negotiable Flag value zero
denotes Not Negotiable and value one denotes
Negotiable."
REFERENCE
"1. Section 4.3, Constraint-Based LSP Setup using
LDP, Jamoussi (Editor), Internet Draft <draft-ietf-
mpls-crldp-06.txt>, November 2001"
DEFVAL { 0 }
::= { mplsTunnelCRLDPResEntry 6 }
mplsTunnelCRLDPResRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table."
Srinivasan et al. Expires July 2002 [Page 46]
Internet Draft MPLS TE MIB January 2002
::= { mplsTunnelCRLDPResEntry 7 }
mplsTunnelCRLDPResStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object."
::= { mplsTunnelCRLDPResEntry 8 }
-- Notifications.
mplsTunnelTrapEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is true, then it enables the
generation of mplsTunnelUp and mplsTunnelDown
traps, otherwise these traps are not emitted."
DEFVAL { false }
::= { mplsTeObjects 11 }
mplsTunnelUp NOTIFICATION-TYPE
OBJECTS {
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}
STATUS current
DESCRIPTION
"This notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to leave the down state
and transition into some other state (but not into
the notPresent state). This other state is
indicated by the included value of
mplsTunnelOperStatus."
::= { mplsTeNotifyPrefix 1 }
mplsTunnelDown NOTIFICATION-TYPE
OBJECTS {
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}
STATUS current
DESCRIPTION
"This notification is generated when a
mplsTunnelOperStatus object for one of the
Srinivasan et al. Expires July 2002 [Page 47]
Internet Draft MPLS TE MIB January 2002
configured tunnels is about to enter the down state
from some other state (but not from the notPresent
state). This other state is indicated by the
included value of mplsTunnelOperStatus."
::= { mplsTeNotifyPrefix 2 }
mplsTunnelRerouted NOTIFICATION-TYPE
OBJECTS {
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}
STATUS current
DESCRIPTION
"This notification is generated when a tunnel is
rerouted. If the actual path is used, then this
tunnel's entry MAY contain the new path for this
tunnel some time after this trap is issued by the
agent."
::= { mplsTeNotifyPrefix 3 }
mplsTunnelReoptimized NOTIFICATION-TYPE
OBJECTS {
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}
STATUS current
DESCRIPTION
"This notification is generated when a tunnel is
reoptimized. If the actual path is used, then this
tunnel's entry MAY contain the new path for this
tunnel some time after this trap is issued by the
agent."
::= { mplsTeNotifyPrefix 4 }
-- End of notifications.
-- Module compliance.
mplsTeGroups
OBJECT IDENTIFIER ::= { mplsTeConformance 1 }
mplsTeCompliances
OBJECT IDENTIFIER ::= { mplsTeConformance 2 }
mplsTeModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support the
MPLS TE MIB."
Srinivasan et al. Expires July 2002 [Page 48]
Internet Draft MPLS TE MIB January 2002
MODULE -- this module
-- The mandatory group has to be implemented by all
-- LSRs that originate/terminate ESLSPs/tunnels.
-- In addition, depending on the type of tunnels
-- supported, other groups become mandatory as
-- explained below.
MANDATORY-GROUPS {
mplsTunnelGroup,
mplsTunnelScalarGroup
}
GROUP mplsTunnelManualGroup
DESCRIPTION
"This group is mandatory for devices which support
manual configuration of tunnels, in addition to
mplsTunnelGroup. The following constraints apply:
mplsTunnelSignallingProto should be at least read-
only with a value of none(1)."
GROUP mplsTunnelSignaledGroup
DESCRIPTION
"This group is mandatory for devices which support
signaled tunnel set up, in addition to
mplsTunnelGroup. The following constraints apply:
mplsTunnelSignallingProto should be at least read-
only returning a value of ldp(2), or rsvp(3)."
GROUP mplsTunnelIsNotIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are not interfaces, in addition to
mplsTunnelGroup. The following constraints apply:
mplsTunnelIsIf must at least be read-only
returning false(1)."
GROUP mplsTunnelIsIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are interfaces, in addition to
mplsTunnelGroup. The following constraints apply:
mplsTunnelIsIf must at least be read-only
returning true(2)."
GROUP mplsTunnelOptionalGroup
DESCRIPTION
"Objects in this group are optional."
-- mplsTunnelTable
Srinivasan et al. Expires July 2002 [Page 49]
Internet Draft MPLS TE MIB January 2002
OBJECT mplsTunnelName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelDescr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelIsIf
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelIfIndex
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelXCPointer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelSignallingProto
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelSetupPrio
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHoldingPrio
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelSessionAttributes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelOwner
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Srinivasan et al. Expires July 2002 [Page 50]
Internet Draft MPLS TE MIB January 2002
OBJECT mplsTunnelLocalProtectInUse
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourcePointer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelInstancePriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopTableIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPrimaryInstance
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPrimaryTimeUp
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPathChanges
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelLastPathChange
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelCreationTime
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelStateTransitions
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Srinivasan et al. Expires July 2002 [Page 51]
Internet Draft MPLS TE MIB January 2002
OBJECT mplsTunnelARHopTableIndex
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelCHopTableIndex
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelAdminStatus
SYNTAX INTEGER { up (1), down (2) }
MIN-ACCESS read-only
DESCRIPTION
"Only up and down states must be supported. Write
access is not required."
OBJECT mplsTunnelOperStatus
SYNTAX INTEGER { up (1), down (2) }
DESCRIPTION
"Only up and down states must be supported. Write
access is not required."
OBJECT mplsTunnelRowStatus
SYNTAX INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
MIN-ACCESS read-only
DESCRIPTION
"The notReady(3) and createAndWait(5) states need
not be supported. Write access is not required."
OBJECT mplsTunnelStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other (1) needs to be supported."
OBJECT mplsTunnelPathInUse
MIN-ACCESS read-only
DESCRIPTION
"Read-only support is required."
OBJECT mplsTunnelRole
SYNTAX INTEGER { head(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only support for head is required."
Srinivasan et al. Expires July 2002 [Page 52]
Internet Draft MPLS TE MIB January 2002
OBJECT mplsTunnelTotalUpTime
MIN-ACCESS read-only
DESCRIPTION
"Read-only support is required."
OBJECT mplsTunnelInstanceUpTime
MIN-ACCESS read-only
DESCRIPTION
"Read-only support is required."
-- mplsTunnelHopTable
OBJECT mplsTunnelHopAddrType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopIpv4Addr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopIpv4PrefixLen
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopIpv6Addr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopIpv6PrefixLen
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopAsNumber
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopLspId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopType
SYNTAX INTEGER { strict(1) }
MIN-ACCESS read-only
Srinivasan et al. Expires July 2002 [Page 53]
Internet Draft MPLS TE MIB January 2002
DESCRIPTION
"loose(2) need not be supported. Write access is
not required."
OBJECT mplsTunnelHopIncludeExclude
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopPathOptionName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopEntryPathComp
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelHopRowStatus
SYNTAX INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
MIN-ACCESS read-only
DESCRIPTION
"The notReady(3) and createAndWait(5) states need
not be supported. Write access is not required."
OBJECT mplsTunnelHopStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other (1) needs to be supported."
-- mplsTunnelResourceTable
OBJECT mplsTunnelResourceMaxRate
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceMeanRate
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceMaxBurstSize
Srinivasan et al. Expires July 2002 [Page 54]
Internet Draft MPLS TE MIB January 2002
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceMeanBurstSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceExcessBurstSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceFrequency
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceWeight
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelResourceRowStatus
SYNTAX INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
MIN-ACCESS read-only
DESCRIPTION
"The notReady(3) and createAndWait(5) states need
not be supported. Write access is not required."
OBJECT mplsTunnelResourceStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other (1) needs to be supported."
-- mplsTunnelPerfTable
OBJECT mplsTunnelPerfPackets
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPerfHCPackets
Srinivasan et al. Expires July 2002 [Page 55]
Internet Draft MPLS TE MIB January 2002
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPerfErrors
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPerfBytes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelPerfHCBytes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { mplsTeCompliances 1 }
-- Units of conformance.
mplsTunnelGroup OBJECT-GROUP
OBJECTS {
mplsTunnelIndexNext,
mplsTunnelName,
mplsTunnelDescr,
mplsTunnelOwner,
mplsTunnelXCPointer,
mplsTunnelIfIndex,
mplsTunnelHopTableIndex,
mplsTunnelARHopTableIndex,
mplsTunnelCHopTableIndex,
mplsTunnelAdminStatus,
mplsTunnelOperStatus,
mplsTunnelRowStatus,
mplsTunnelTrapEnable,
mplsTunnelStorageType,
mplsTunnelConfigured,
mplsTunnelActive,
mplsTunnelPrimaryInstance,
mplsTunnelPrimaryTimeUp,
mplsTunnelPathChanges,
mplsTunnelLastPathChange,
mplsTunnelCreationTime,
mplsTunnelStateTransitions,
mplsTunnelIncludeAnyAffinity,
mplsTunnelIncludeAllAffinity,
Srinivasan et al. Expires July 2002 [Page 56]
Internet Draft MPLS TE MIB January 2002
mplsTunnelExcludeAllAffinity,
mplsTunnelPerfPackets,
mplsTunnelPerfHCPackets,
mplsTunnelPerfErrors,
mplsTunnelPerfBytes,
mplsTunnelPerfHCBytes,
mplsTunnelResourcePointer,
mplsTunnelInstancePriority,
mplsTunnelPathInUse,
mplsTunnelRole,
mplsTunnelTotalUpTime,
mplsTunnelInstanceUpTime
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to
implement tunnels. In addition, depending on the
type of the tunnels supported (for example,
manually configured or signaled, persistent or non-
persistent, etc.), the following other groups
defined below are mandatory: mplsTunnelManualGroup
and/or mplsTunnelSignaledGroup,
mplsTunnelIsNotIntfcGroup and/or
mplsTunnelIsIntfcGroup."
::= { mplsTeGroups 1 }
mplsTunnelManualGroup OBJECT-GROUP
OBJECTS { mplsTunnelSignallingProto }
STATUS current
DESCRIPTION
"Object(s) needed to implement manually configured
tunnels."
::= { mplsTeGroups 2 }
mplsTunnelSignaledGroup OBJECT-GROUP
OBJECTS {
mplsTunnelSetupPrio,
mplsTunnelHoldingPrio,
mplsTunnelSignallingProto,
mplsTunnelLocalProtectInUse,
mplsTunnelSessionAttributes,
mplsTunnelHopListIndexNext,
mplsTunnelHopAddrType,
mplsTunnelHopIpv4Addr,
mplsTunnelHopIpv4PrefixLen,
mplsTunnelHopIpv6Addr,
mplsTunnelHopIpv6PrefixLen,
mplsTunnelHopAsNumber,
mplsTunnelHopLspId,
mplsTunnelHopType,
Srinivasan et al. Expires July 2002 [Page 57]
Internet Draft MPLS TE MIB January 2002
mplsTunnelHopIncludeExclude,
mplsTunnelHopPathOptionName,
mplsTunnelHopEntryPathComp,
mplsTunnelHopRowStatus,
mplsTunnelHopStorageType
}
STATUS current
DESCRIPTION
"Object needed to implement signaled tunnels."
::= { mplsTeGroups 3 }
mplsTunnelScalarGroup OBJECT-GROUP
OBJECTS {
mplsTunnelConfigured,
mplsTunnelActive,
mplsTunnelTEDistProto,
mplsTunnelMaxHops
}
STATUS current
DESCRIPTION
"Scalar object needed to implement MPLS tunnels."
::= { mplsTeGroups 4 }
mplsTunnelIsIntfcGroup OBJECT-GROUP
OBJECTS { mplsTunnelIsIf }
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are
interfaces."
::= { mplsTeGroups 5 }
mplsTunnelIsNotIntfcGroup OBJECT-GROUP
OBJECTS { mplsTunnelIsIf }
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are not
interfaces."
::= { mplsTeGroups 6 }
mplsTunnelOptionalGroup OBJECT-GROUP
OBJECTS {
mplsTunnelResourceIndexNext,
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate,
mplsTunnelResourceMaxBurstSize,
mplsTunnelResourceMeanBurstSize,
mplsTunnelResourceExcessBurstSize,
mplsTunnelResourceFrequency,
mplsTunnelResourceWeight,
mplsTunnelResourceRowStatus,
Srinivasan et al. Expires July 2002 [Page 58]
Internet Draft MPLS TE MIB January 2002
mplsTunnelResourceStorageType,
mplsTunnelARHopAddrType,
mplsTunnelARHopIpv4Addr,
mplsTunnelARHopIpv4PrefixLen,
mplsTunnelARHopIpv6Addr,
mplsTunnelARHopIpv6PrefixLen,
mplsTunnelARHopAsNumber,
mplsTunnelARHopLspId,
mplsTunnelCHopAddrType,
mplsTunnelCHopIpv4Addr,
mplsTunnelCHopIpv4PrefixLen,
mplsTunnelCHopIpv6Addr,
mplsTunnelCHopIpv6PrefixLen,
mplsTunnelCHopAsNumber,
mplsTunnelCHopLspId,
mplsTunnelCHopType
}
STATUS current
DESCRIPTION
"The objects in this group are optional."
::= { mplsTeGroups 7 }
mplsTunnelCRLDPResOptionalGroup OBJECT-GROUP
OBJECTS {
mplsTunnelCRLDPResMeanBurstSize,
mplsTunnelCRLDPResExcessBurstSize,
mplsTunnelCRLDPResFrequency,
mplsTunnelCRLDPResWeight,
mplsTunnelCRLDPResFlags,
mplsTunnelCRLDPResRowStatus,
mplsTunnelCRLDPResStorageType
}
STATUS current
DESCRIPTION
"Set of objects implemented for resources applicable
for tunnels signaled using CR-LDP."
::= { mplsTeGroups 8 }
mplsTeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
mplsTunnelUp,
mplsTunnelDown,
mplsTunnelRerouted,
mplsTunnelReoptimized
}
STATUS current
DESCRIPTION
"Set of notifications implemented in this module.
None is mandatory."
::= { mplsTeGroups 9 }
Srinivasan et al. Expires July 2002 [Page 59]
Internet Draft MPLS TE MIB January 2002
END
11. Security Considerations
There are a number of management objects defined in this
MIB that have a MAX-ACCESS clause of read-write and/or
read-create. Such objects may be considered sensitive or
vulnerable in some network environments. The support for
SET operations in a non-secure environment without proper
protection can have a negative effect on network
operations.
It is thus important to control even GET access to these
objects and possibly to even encrypt the values of these
object when sending them over the network via SNMP. Not
all versions of SNMP provide features for such a secure
environment.
SNMPv1 by itself is not a secure environment. Even if the
network itself is secure (for example by using IPSec
[RFC2401]), there is no control as to who on the secure
network is allowed to access and GET/SET
(read/change/create/delete) the objects in this MIB. It is
recommended that the implementers consider the security
features as provided by the SNMPv3 framework.
Specifically, the use of the User-based Security Model
[RFC2574] and the View- based Access Control [RFC2575] is
recommended. It is then a customer/user responsibility to
ensure that the SNMP entity giving access to an instance
of this MIB, is properly configured to give access to the
objects only to those principals (users) that have
legitimate rights to indeed GET or SET
(change/create/delete) them.
12. Acknowledgments
We wish to thank Adrian Farrel, Eric Gray, Joan Cucchiara,
Patrick Kerharo, Paul Langille and Mike Piecuch for their
comments on this draft.
13. References
[Assigned] Reynolds, J., and J. Postel, "Assigned
Numbers", RFC 1700, October 1994. See also:
http://www.isi.edu/in-
notes/iana/assignments/smi-numbers
Srinivasan et al. Expires July 2002 [Page 60]
Internet Draft MPLS TE MIB January 2002
[TCMIB] Nadeau, T., Cucchiara, J., Srinivasan, C,
Viswanathan, A. and H. Sjostrand,
"Definition of Textual Conventions and
OBJECT-IDENTITIES for Multi-Protocol Label
Switching (MPLS) Management", Internet Draft
<draft-ietf-mpls-tc-mib-03.txt>, January
2002.
[LSRMIB] Srinivasan, C., Viswanathan, A. and T.
Nadeau, "MPLS Label Switch Router Management
Information Base ", Internet Draft <draft-
ietf-mpls-lsr-mib-08.txt>, January 2002.
[CRLDP] B. Jamoussi (Editor), "Constraint-Based LSP
Setup using LDP", Internet Draft <draft-ietf-
mpls-cr-ldp-06.txt>, November 2001.
[RFC1155] Rose, M., and K. McCloghrie, "Structure and
Identification of Management Information for
TCP/IP-based Internets", RFC 1155, May 1990.
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J.
Davin, "Simple Network Management Protocol",
RFC 1157, May 1990.
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB
Definitions", RFC 1212, March 1991.
[RFC1215] M. Rose, "A Convention for Defining Traps
for use with the SNMP", RFC 1215, March
1991.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Introduction to Community-based
SNMPv2", RFC 1901, January 1996.
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for Version
2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Transport Mappings for Version
2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996.
[RFC2026] S. Bradner, "The Internet Standards Process
-- Revision 3", RFC 2026, October 1996.
Srinivasan et al. Expires July 2002 [Page 61]
Internet Draft MPLS TE MIB January 2002
[RFC2401] Kent, S., and Atkinson, R., "Security
Architecture for the Internet Protocol", RFC
2401, November 1998.
[RFC2570] Case, J., Mundy, R., Partain, D., and B.
Stewart, "Introduction to Version 3 of the
Internet-standard Network Management
Framework", RFC 2570, April 1999.
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen,
"An Architecture for Describing SNMP
Management Frameworks", RFC 2571, April
1999.
[RFC2572] Case, J., Harrington D., Presuhn R., and B.
Wijnen, "Message Processing and Dispatching
for the Simple Network Management Protocol
(SNMP)", RFC 2572, April 1999.
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3
Applications", RFC 2573, April 1999.
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based
Security Model (USM) for version 3 of the
Simple Network Management Protocol
(SNMPv3)", RFC 2574, April 1999.
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie,
"View-based Access Control Model (VACM) for
the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder,
J., Case, J., Rose, M., and S. Waldbusser,
"Structure of Management Information Version
2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder,
J., Case, J., Rose, M., and S. Waldbusser,
"Textual Conventions for SMIv2", STD 58, RFC
2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder,
J., Case, J., Rose, M., and S. Waldbusser,
"Conformance Statements for SMIv2", STD 58,
RFC 2580, April 1999.
[RFC2851] Daniele, M., Haberman, B., Routhier, S., and
J. Schoenwaelder, "Textual Conventions for
Internet Network Addresses", RFC 2851, June
Srinivasan et al. Expires July 2002 [Page 62]
Internet Draft MPLS TE MIB January 2002
2000.
[RFC2863] McCloghrie, K. and F. Kastenholtz, "The
Interfaces Group MIB ", RFC 2863, June 2000.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching
Architecture", RFC 3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC
3209, December 2001.
14. Authors' Addresses
Cheenu Srinivasan
Parama Networks, Inc.
1030 Broad Street
Shrewsbury, NJ 07702
Phone: +1-732-544-9120 x731
Email: cheenu@paramanet.com
Arun Viswanathan
Force10 Networks, Inc.
1440 McCarthy Blvd
Milpitas, CA 95035
Phone: +1-408-571-3516
Email: arun@force10networks.com
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
15. Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights
Reserved.
This document and translations of it may be copied and
furnished to others, and derivative works that comment on
or otherwise explain it or assist in its implementation may
be prepared, copied, published and distributed, in whole or
in part, without restriction of any kind, provided that the
above copyright notice and this paragraph are included on
Srinivasan et al. Expires July 2002 [Page 63]
Internet Draft MPLS TE MIB January 2002
all such copies and derivative works. However, this
document itself may not be modified in any way, such as by
removing the copyright notice or references to the Internet
Society or other Internet organizations, except as needed
for the purpose of developing Internet standards in which
case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to
translate it into languages other than English.
The limited permissions granted above are perpetual and
will not be revoked by the Internet Society or its
successors or assigns. This document and the information
contained herein is provided on an "AS IS" basis and THE
INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE
DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
Srinivasan et al. Expires July 2002 [Page 64]