Network Working Group N. Bahadur
Internet-Draft R. Aggarwal
Updates: 4379 (if approved) Juniper Networks, Inc.
Intended status: Standards Track S. Boutros
Expires: September 15, 2011 Cisco Systems, Inc.
E. Gray
Ericsson
March 14, 2011
MPLS On-demand Connectivity Verification and Route Tracing
draft-ietf-mpls-tp-on-demand-cv-03
Abstract
LSP-Ping is an existing and widely deployed OAM mechanism for MPLS
LSPs. This document describes extensions to LSP-Ping so that LSP-
Ping can be used for On-demand Connectivity Verification of MPLS-TP
LSPs. This document also clarifies procedures to be used for
processing the related OAM packets. Further, it describes procedures
for using LSP-Ping to perform Connectivity Verification and Route
Tracing functions in MPLS-TP networks. Finally this document updates
RFC 4379 by adding a new address type and requesting a registry.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 15, 2011.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Bahadur, et al. Expires September 15, 2011 [Page 1]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Conventions used in this document . . . . . . . . . . . . 4
1.2. On-demand CV for MPLS-TP LSPs using IP encapsulation . . . 4
1.3. On-demand CV for MPLS-TP LSPs using non-IP
encapsulation . . . . . . . . . . . . . . . . . . . . . . 5
2. LSP-Ping Extensions . . . . . . . . . . . . . . . . . . . . . 5
2.1. New address type for Downstream Mapping TLV . . . . . . . 5
2.1.1. DSMAP/DDMAP Based Non-IP Address TLV . . . . . . . . . 5
2.2. Source/Destination Address TLV . . . . . . . . . . . . . . 6
2.2.1. Source/Destination Non-IP Address TLV Format . . . . . 6
2.2.2. Source Address TLV . . . . . . . . . . . . . . . . . . 7
2.2.3. Destination Address TLV . . . . . . . . . . . . . . . 7
2.3. Identifying Statically provisioned LSPs and PWs . . . . . 7
2.3.1. Static LSP Sub-TLV . . . . . . . . . . . . . . . . . . 7
2.3.2. Static Pseudowire Sub-TLV . . . . . . . . . . . . . . 8
3. Performing On-demand CV over MPLS-TP LSPs . . . . . . . . . . 9
3.1. LSP-Ping with IP encapsulation . . . . . . . . . . . . . . 9
3.2. On-demand CV with IP encapsulation, over ACH . . . . . . . 9
3.3. Non-IP based On-demand CV, using ACH . . . . . . . . . . . 10
3.4. Reverse Path Connectivity Verification . . . . . . . . . . 11
3.4.1. Requesting Reverse Path Connectivity Verification . . 11
3.4.2. Egress Procedures . . . . . . . . . . . . . . . . . . 11
3.4.3. Ingress Procedures . . . . . . . . . . . . . . . . . . 12
3.5. P2MP Considerations . . . . . . . . . . . . . . . . . . . 12
3.6. Operation of On-demand CV with Static MPLS-TP . . . . . . 12
3.7. GAL Label Processing . . . . . . . . . . . . . . . . . . . 12
4. Performing on-demand Route Tracing over MPLS-TP LSPs . . . . . 13
4.1. On-demand LSP Route Tracing with IP encapsulation . . . . 13
4.2. Non-IP based On-demand LSP Route Tracing, using ACH . . . 13
4.2.1. Ingress node procedure for sending echo request
packets . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.2. Ingress node procedure for receiving echo response
packets . . . . . . . . . . . . . . . . . . . . . . . 14
4.2.3. Transit and egress node procedure . . . . . . . . . . 14
4.3. P2MP Considerations . . . . . . . . . . . . . . . . . . . 14
4.4. ECMP Considerations . . . . . . . . . . . . . . . . . . . 14
5. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 14
Bahadur, et al. Expires September 15, 2011 [Page 2]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
6. Security Considerations . . . . . . . . . . . . . . . . . . . 14
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15
7.1. New Source and Destination Address TLVs . . . . . . . . . 15
7.2. New Target FEC Stack Sub-TLVs . . . . . . . . . . . . . . 15
7.3. New Reverse-path Target FEC Stack TLV . . . . . . . . . . 15
7.4. New Pseudowire Associated Channel Type . . . . . . . . . . 16
7.5. New RFC 4379 Registry . . . . . . . . . . . . . . . . . . 16
8. Contributing Authors . . . . . . . . . . . . . . . . . . . . . 17
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9.1. Normative References . . . . . . . . . . . . . . . . . . . 17
9.2. Informative References . . . . . . . . . . . . . . . . . . 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 18
Bahadur, et al. Expires September 15, 2011 [Page 3]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
1. Introduction
LSP-Ping [RFC4379] is an OAM mechanism for MPLS LSPs. This document
describes extensions to LSP-Ping so that LSP-Ping can be used for on-
demand monitoring of MPLS-TP LSPs. It also clarifies the procedures
to be used for processing the OAM packets. This document describes
how LSP-Ping can be used for on-demand Connectivity Verification
(Section 3) and Route Tracing (Section 4) functions required in
[RFC5860] and specified in [I-D.ietf-mpls-tp-oam-framework].
1.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
In addition, there is considerable opportunity for confusion in use
of the terms "on-demand connectivity verification" (CV), "on-demand
route tracing" and "LSP-Ping." In this document, we try to use the
terms consistently as follows:
LSP-Ping: refers to the mechanism - particularly as defined and used
in referenced material;
On-demand CV: refers to on-demand connectivity verification and -
where both apply equally - on-demand route tracing as implemmented
using the LSP-Ping mechanism as extended for support of MPLS-TP;
On-demand route tracing: used in those cases where the LSP-Ping
mechanism (as extended) is used exclusively for route tracing.
1.2. On-demand CV for MPLS-TP LSPs using IP encapsulation
LSP-Ping requires IP addressing on the egress and transit LSRs for
performing OAM on MPLS signaled LSPs and pseudowires. In particular,
in these cases the LSP-Ping packets generated by an ingress LSR are
encapsulated in an IP/UDP header with the destination address from
the 127/8 range and then encapsulated in the MPLS label stack
([RFC4379] , [RFC5884]). Egress LSRs use the presence of the 127/8
destination address to identify the OAM packets and rely further on
the UDP port number to determine whether the packet is a LSP-Ping
packet. It is to be noted that this determination does not require
IP forwarding capabilities. It requires the presence of an IP host
stack which enables egress LSRs to process packets with a destination
address from the 127/8 range. [RFC1122] allocates the 127/8 range as
"Internal host loopback address" and [RFC1812] states that "a router
SHOULD NOT forward, except over a loopback interface, any packet that
has a destination address on network 127".
Bahadur, et al. Expires September 15, 2011 [Page 4]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
1.3. On-demand CV for MPLS-TP LSPs using non-IP encapsulation
In certain MPLS-TP deployment scenarios IP addressing might not be
available or it may be preferred to use some form of non-IP
encapsulation for On-demand CV, route tracing and BFD packets. In
such scenarios, On-demand CV and/or route tracing SHOULD be run
without IP addressing, using the ACH channel type specified in
Section 3.
Section 3.3 and Section 4.2 describe the theory of operation for
performing On-demand CV over MPLS-TP LSPs with any non-IP
encapsulation.
2. LSP-Ping Extensions
2.1. New address type for Downstream Mapping TLV
[RFC4379] defines the Downstream Mapping TLV. This document defines
the following new Address type which is added to the Downstream
Mapping TLV:
Type # Address Type K Octets
------ -------------- --------
5 Non IP 12
Figure 1: Downstream Mapping TLV new address type
The new address type indicates that no address is present in the
Downstream Mapping TLV. Multipath type SHOULD be set to 0 (no
multipath) when using this address type.
When this address type is used, on receipt of a LSP-Ping echo
request, interface verification MUST be bypassed. Thus the receiving
node SHOULD only perform mpls label control-plane/data-plane
consistency checks.
The new address type is also applicable to the Detailed Downstream
Mapping TLV defined in [I-D.ietf-mpls-lsp-ping-enhanced-dsmap].
2.1.1. DSMAP/DDMAP Based Non-IP Address TLV
When sending On-demand CV packets using ACH, without IP
encapsulation, the following information MUST be included in any
(source/destination) TLV that is included in the packet. This
information forms the address portion of an address TLV as defined in
as defined in [RFC4379] (and extended here).
Bahadur, et al. Expires September 15, 2011 [Page 5]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MTU | Address Type | DS Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ingress IF-Num (4 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Egress IF-Num (4 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Multipath Type| Depth Limit | Multipath Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: New DSMAP/DDMAP Address Format
Address Type will be 5 (as shown in Section 2.1 above.
Multipath type SHOULD be set to 0 (no multipath) when using this
address type.
2.2. Source/Destination Address TLV
2.2.1. Source/Destination Non-IP Address TLV Format
The format for the address TLV is the same for both source and
destination address TLVs (only the type is different). The format is
as specified in the figure below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type=TBD | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Global_ID (4 Octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Node_ID (4 Octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: New Source/Destination Address Format
Type will be one of either TBD-SRC or TBD-DST, depending on whether
the TLV in question is a source or destination address TLV.
Global_ID is as defined in [I-D.ietf-mpls-tp-identifiers].
Node_ID is as defined in [I-D.ietf-mpls-tp-identifiers].
Bahadur, et al. Expires September 15, 2011 [Page 6]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
2.2.2. Source Address TLV
When sending On-demand CV packets using ACH, without IP
encapsulation, there MAY be a need to identify the source address of
the packet. This source address will be specified via the Source
Address TLV, using the address TLV defined in [RFC4379] (and extended
by this document, containing the information specified in
Section 2.1.1, above.
An On-demand CV packet MUST NOT include more than 1 source address
TLV. The source address MUST specify the address of the originator
of the packet. If more than 1 such TLV is present in an On-demand CV
request packet, then an error of 1 (Malformed echo request received,
Section 3.3 [RFC4379]) MUST be returned, if it is possible to
unambiguously identify the source of the packet.
2.2.3. Destination Address TLV
An On-demand CV packet MUST NOT include more than 1 destination
address TLV. The destination address MUST specify a valid address of
the destination node for the packet. If more than 1 such TLV is
present in an On-demand CV request packet, then an error of 1
(Malformed echo request received, Section 3.3 [RFC4379]) MUST be
returned, if it is possible to unambiguously identify the source of
the packet.
2.3. Identifying Statically provisioned LSPs and PWs
[RFC4379] specifies how an MPLS LSP under test may be identified in
an echo request. A Target FEC Stack TLV is used to identify the LSP.
In order to identify a statically provisioned LSP and PW, new target
FEC stack sub-TLVs are being defined. The new sub-TLVs are assigned
sub-type identifiers as follows, and are described in the following
sections.
Type # Sub-Type # Length Value Field
------ ---------- ------ -----------
1 22 24 Static LSP
1 23 24 Static Pseudowire
Figure 4: New target FEC sub-types
2.3.1. Static LSP Sub-TLV
The format of the Static LSP sub-TLV value field is specified in the
following figure. The value fields are taken from the definitions in
[I-D.ietf-mpls-tp-identifiers].
Bahadur, et al. Expires September 15, 2011 [Page 7]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Tunnel Number | LSP Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Tunnel Number | Must be Zero |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Static LSP FEC Sub-TLV
The Source global ID and Destination Global ID MAY be set to 0. When
set to zero, the field is not applicable.
2.3.2. Static Pseudowire Sub-TLV
The format of the Static PW sub-TLV value field is specified in the
following figure.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source AC-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination AC-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Static PW FEC Sub-TLV
The Source global ID and Destination Global ID MAY be set to 0. When
set to zero, the field is not applicable. The Global ID and Node ID
Bahadur, et al. Expires September 15, 2011 [Page 8]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
fields are taken from the definitions in
[I-D.ietf-mpls-tp-identifiers]. The AC-ID definitions are taken from
[RFC5003].
3. Performing On-demand CV over MPLS-TP LSPs
This section specifies how On-demand CV can be used in the context of
MPLS-TP LSPs. The On-demand CV function meets the On-demand
Connectivity Verification requirements specified in [RFC5860],
section 2.2.3. This function SHOULD NOT be performed except in the
on-demand mode. This function SHOULD be performed between End Points
(MEPs) and Intermediate Points (MIPs) of PWs and LSPs, and between
End Points of PWs, LSPs and Sections. In order for the On-demand CV
packet to be processed at the desired MIP, the TTL of the MPLS label
should be set such that it expires at the MIP to be probed.
[RFC5586] defines an ACH mechanism for MPLS LSPs. The mechanism is a
generalization of Associated Channel mechanism that [RFC4385] defined
for use with Pseudowires. As a result, a single Associated Channel
Type may be used for either an LSP or Pseudowire.
A new Pseudowire Associated Channel Type (type TBD-2) is defined for
use in performing On-demand Connectivity Verification. Its use is
described in the following sections.
3.1. LSP-Ping with IP encapsulation
LSP-Ping packets, as specified in [RFC4379], are sent over the MPLS
LSP for which OAM is being performed and contain an IP/UDP packet
within them. The IP header is not used for forwarding (since LSP
forwarding is done using MPLS label switching). The IP header is
used mainly for addressing and can be used in the context of MPLS-TP
LSPs. This form of On-demand CV OAM MUST be supported for MPLS-TP
LSPs when IP addressing is in use.
The On-demand CV echo response message MUST be sent on the reverse
path of the LSP. The reply MUST contain IP/UDP headers followed by
the On-demand CV payload. The destination address in the IP header
MUST be set to that of the sender of the echo request message. The
source address in the IP address MUST be set to a valid address of
the replying node.
3.2. On-demand CV with IP encapsulation, over ACH
IP encapsulated On-demand CV packets MAY be sent over the MPLS LSP
using the control channel (ACH). IP ACH type specified in [RFC4385]
MUST be used in such a case. The IP header is used mainly for
Bahadur, et al. Expires September 15, 2011 [Page 9]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
addressing and can be used in the context of MPLS-TP LSPs.
The On-demand CV echo response message MUST be sent on the reverse
path of the LSP. The response in this case SHOULD use ACH and SHOULD
be IP encapsulated.
If IP encapsulated, the destination address in the IP header MUST be
set to that of the sender of the echo request message, and the source
address in the IP header MUST be set to a valid address of the
replying node.
3.3. Non-IP based On-demand CV, using ACH
The OAM procedures defined in [RFC4379] require the use of IP
addressing, and in some cases IP routing, to perform OAM functions.
When the ACH header is used, IP addressing and routing is not needed.
This section describes procedures for performing on-demand CV without
a dependency on IP addressing and routing.
When using On-demand CV via LSP-Ping with the ACH header, the LSP-
Ping Reply mode [RFC4379] in the LSP-Ping echo request MUST be set to
4 (Reply via application level control channel).
Note that the application level control channel in this case is the
reverse path of the LSP (or Pseudowire) using ACH.
The requesting node MAY attach a Source Address TLV (Section 2.2) to
identify the node originating the request.
The On-demand CV reply message MUST be sent on the reverse path of
the LSP using ACH. The On-demand CV payload MUST directly follow the
ACH header (and any ACH TLVs) and no IP and/or UDP headers MUST be
attached. The responding node MAY attach a Source Address TLV to
identify the node sending the response.
If a node receives an MPLS echo request packet over ACH, without IP/
UDP headers, with a reply mode of 4, and if that node does not have a
return MPLS LSP path to the echo request source, then the node SHOULD
drop the echo request packet and not attempt to send a response.
If a node receives an MPLS echo request with a reply mode other than
4 (reply via application level control channel), and if the node
supports that reply mode, then it MAY respond using that reply mode.
If the node does not support the reply mode requested, or is unable
to reply using the requested reply mode in any specific instance, the
node MUST drop the echo request packet and not attempt to send a
response.
Bahadur, et al. Expires September 15, 2011 [Page 10]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
3.4. Reverse Path Connectivity Verification
3.4.1. Requesting Reverse Path Connectivity Verification
A new global flag, Validate Reverse Path (R), is being defined in the
LSP-Ping packet header. When this flag is set in the echo request,
the LSP-egress SHOULD return reverse path FEC information, as
described in Section 3.4.2.
The R flag MUST NOT be set in the echo response. If it is set in the
echo response, it should be ignored.
The Global Flags field is now a bit vector with the following format:
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MBZ |R|T|V|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: Global Flags Field
The V flag is defined in [RFC4379]. The T flag is defined in P2MP-
LSP-PING. The R flag is defined in this draft.
The Validate FEC Stack (V) flag MAY be set in the echo response when
reverse path connectivity verification is being performed.
3.4.2. Egress Procedures
When the R flag is set in the echo request, the egress node MAY
attach a new TLV, Reverse-path target FEC stack TLV, in the echo
response. The requesting node (on receipt of the response) can use
the Reverse-path target FEC stack TLV to perform reverse path
connectivity verification. For co-routed bi-directional LSPs, the
Reverse-path target FEC stack used for On-demand CV will be the same
in both the forward and reverse path of the LSP. For associated bi-
directional LSPs, the target FEC stack will be different for the
reverse path.
The format of the Reverse-path target FEC stack TLV is the same as
that of the Target FEC stack TLV defined in [RFC4379]. The rules for
creating a Target FEC stack TLV also apply to the Reverse-path target
FEC stack TLV.
Bahadur, et al. Expires September 15, 2011 [Page 11]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
Value TLV
-------- ------------------------------------
TBD-1 Reverse-path target FEC stack
Figure 8: Reverse-Path Target FEC Stack TLV Type
3.4.3. Ingress Procedures
On receipt of the echo response, the requesting node MUST perform the
following checks:
1. Perform interface and label-stack validation to ensure that the
packet is received on the reverse path of the bi-directional LSP
2. If the Reverse-Path target FEC stack stack TLV is present in the
echo response, then perform FEC validation.
If any of the validations fail, then the requesting node MUST drop
the echo response and report an error.
3.5. P2MP Considerations
[I-D.ietf-mpls-p2mp-lsp-ping] describes how LSP-Ping can be used for
OAM on P2MP LSPs with IP encapsulation. This MUST be supported for
MPLS-TP P2MP LSPs when IP addressing is used. When IP addressing is
not used, then the procedures described in Section 3.3 can be applied
to P2MP MPLS-TP LSPs as well.
3.6. Operation of On-demand CV with Static MPLS-TP
Support for static MPLS-TP LSP, or Pseudowire, usage and on-demand
CV, requires manageable objects necessary to, for instance, configure
operating parameters such as duration and periodicity of an on-demand
connectivity test.
The specifics of this manageability requirement are out-of-scope in
this document and SHOULD be addressed in an appropriate management
specification.
3.7. GAL Label Processing
At the ingress PE, when encapsulating the LSP echo request (LSP Ping)
packet (with the IP ACH, or the non IP ACH, codepoint), a GAL label
MUST be added before adding the MPLS LSP label, and sending the LSP
Ping echo request packet in-band in the MPLS LSP.
The GAL label MUST NOT be considered as part of the MPLS label stack
that requires verification by the egress PE. For this reason, a NIL
Bahadur, et al. Expires September 15, 2011 [Page 12]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
FEC Stack TLV MUST NOT be added or associated with the GAL label.
GAL Label MUST NOT be included in DSMAP or DDMAP TLVs.
Interface and label stack TLV MUST include the whole label stack
including the GAL label.
4. Performing on-demand Route Tracing over MPLS-TP LSPs
This section specifies how On-demand CV traceroute can be used in the
context of MPLS-TP LSPs. The On-demand CV traceroute function meets
the Route Tracing requirement specified in [RFC5860], section 2.2.4.
This function SHOULD be performed on-demand. This function SHOULD be
performed between End Points and Intermediate Points of PWs and LSPs,
and between End Points of PWs, LSPs and Sections.
When performing On-demand CV traceroute, the requesting node inserts
a Downstream Mapping TLV to get the downstream node information and
to enable LSP verification along the transit nodes. The Downstream
Mapping TLV can be used as is for performing the traceroute. If IP
addressing is not in use, then the Address Type field in the
Downstream Mapping TLV can be set to "Not applicable" (Section 2.1).
The Downstream Mapping TLV address type field can be extended to
include other address types as need be.
4.1. On-demand LSP Route Tracing with IP encapsulation
The mechanics of On-demand CV traceroute are similar to those
described for ping in Section 3.1. On-demand Route Tracing packets
sent by the LSP ingress MUST follow procedures described in
[RFC4379]. This form of On-demand CV OAM MUST be supported for
MPLS-TP LSPs, when IP addressing is used.
4.2. Non-IP based On-demand LSP Route Tracing, using ACH
This section describes procedures for performing LSP traceroute when
using LSP-Ping with the ACH header and without any dependency on IP
addressing. The procedures specified in Section 3.3 with regards to
Source Address TLV, MEP/MIP identifiers apply to LSP traceroute as
well.
4.2.1. Ingress node procedure for sending echo request packets
On-demand Route Tracing packets sent by the LSP ingress MUST adhere
to the format described in Section 3.3. MPLS-TTL expiry (as
described in [RFC4379]) will be used to direct the packets to
specific nodes along the LSP path.
Bahadur, et al. Expires September 15, 2011 [Page 13]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
4.2.2. Ingress node procedure for receiving echo response packets
The On-demand CV traceroute responses will be received on the LSP
itself and the presence of an ACH header with channel type of On-
demand CV is an indicator that the packet contains On-demand CV
payload.
4.2.3. Transit and egress node procedure
When a echo request reaches the transit or egress, the presence of
the ACH channel type of On-demand CV will indicate that the packet
contains On-demand CV data. The On-demand CV data, the label stack
and the MEP/MIP identifier should be sufficient to identify the LSP
associated with the echo request packet. If there is an error and
the node is unable to identify the LSP on which the echo response
would to be sent, the node MUST drop the echo request packet and not
send any response back. All responses MUST always be sent on a LSP
path using the ACH header and ACH channel type of On-demand CV.
4.3. P2MP Considerations
[I-D.ietf-mpls-p2mp-lsp-ping] describes how LSP-Ping can be used for
OAM on P2MP LSPs. This MUST be supported for MPLS-TP P2MP LSPs when
IP addressing is used. When IP addressing is not used, then the
procedures described in Section 4.2 can be applied to P2MP MPLS-TP
LSPs as well.
4.4. ECMP Considerations
On-demand CV using ACH SHOULD NOT be used when there is ECMP (equal
cost multiple paths) for a given LSP. The addition of the additional
ACH header may modify the hashing behavior for OAM packets which may
result in incorrect monitoring of path taken by data traffic.
5. Applicability
The procedures specified in this document for non-IP encapsulation
apply only to MPLS-TP Transport paths. This includes LSPs and PWs
when IP encapsulation is not desired. However, when IP addressing is
used, as in non MPLS-TP LSPs, procedures specified in [RFC4379] MUST
be used.
6. Security Considerations
The draft does not introduce any new security considerations. Those
discussed in [RFC4379] are also applicable to this document.
Bahadur, et al. Expires September 15, 2011 [Page 14]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
7. IANA Considerations
7.1. New Source and Destination Address TLVs
IANA is requested to assign the following TLV types from the "Label
Switched Paths (LSPs) Parameters - TLVs" Registry, "TLVs and sub-
TLVs" sub-registry (from "Standards Action" TLV type range):
Length
Type # TLV Name Octets Reference
------ ----------------------- ------ ------------------------
TBD-SRC Source Address TLV 8 this document (sect 2.2)
TBD-DST Destination Address TLV 8 this document (sect 2.2)
Figure 9: New Source/Destination Address TLV Type
7.2. New Target FEC Stack Sub-TLVs
Section 2.3 defines 2 new sub-TLV types for inclusion within the LSP
Ping [RFC4379] Target FEC Stack TLV.
IANA is requested to assign sub-type values to the following sub-TLVs
from the "Multiprotocol Label Switching Architecture (MPLS) Label
Switched Paths (LSPs) Parameters - TLVs" registry, "TLVs and sub-
TLVs" sub-registry.
Value Meaning Reference
----- ------------------------- --------------------------
22 Static LSP sub-TLV this document (sect 2.4.1)
23 Static Pseudowire sub-TLV this document (sect 2.4.2)
7.3. New Reverse-path Target FEC Stack TLV
Section 3.4.2 defines a new TLV type for inclusion in the LSP-Ping
packet.
IANA is requested to assign a type value to the TLV from the
"Multiprotocol Label Switching Architecture (MPLS) Label Switched
Paths (LSPs) Parameters - TLVs" registry, "TLVs and sub-TLVs" sub-
registry.
Value Meaning Reference
----- -------------------------- ------------------------
TBD-1 Reverse-path Target FEC this document (sect 3.4)
Stack TLV
The sub-TLV space and assignments for this TLV will be the same as
Bahadur, et al. Expires September 15, 2011 [Page 15]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
that for the Target FEC Stack TLV. Sub-types for the Target FEC
Stack TLV and the Reverse-path Target FEC Stack TLV MUST be kept the
same. Any new sub-type added to the Target FEC Stack TLV MUST apply
to the Reverse-path Target FEC Stack TLV as well.
7.4. New Pseudowire Associated Channel Type
On-demand Connectivity Verification requires a unique Associated
Channel Type. IANA is requested to assign a PW ACh Type from the
"Pseudowire Associated Channel Type Registry" as describe below:
Value Description TLV Follows Reference
------ ------------- ----------- ----------------------
TBD-2 On-Demand CV No this document (sect 3)
7.5. New RFC 4379 Registry
[RFC4379] defined several registries. It also defined some value
assignments without explicitly asking for IANA to create a registry
to support additional value assingments. One such case is in
defining address types associated with the Downstream Mapping (DSMAP)
TLV.
This document extends RFC 4379 by defining a new address type for use
with the Downstream Mapping TLV.
Recognizing that the absence of a registry makes it possible to have
collisions of "address-type" usages, IANA is requested to establish a
new registry - associated with both [RFC4379] and this document -
that initially allocates the following assignments:
Type # Address Type K Octets Reference
------ ------------ -------- --------------------------
1 IPv4 Numbered 16 RFC 4379
2 IPv4 Unnumbered 16 RFC 4379
3 IPv6 Numbered 40 RFC 4379
4 IPv6 Unnumbered 28 RFC 4379
5 Non IP 12 this document (sect 2.1.1)
Downstream Mapping Address Type Registry
Because the field in this case is an 8-octet field, the basis for all
future allocations SHOULD be "Standards Based."
Bahadur, et al. Expires September 15, 2011 [Page 16]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
8. Contributing Authors
The following individuals also contributed to this document:
o Thomas D. Nadeau, Huawei
o Nurit Sprecher, Nokia Siemens Networks
o Yaacov Weingarten, Nokia Siemens Networks
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4379] Kompella, K. and G. Swallow, "Detecting Multi-Protocol
Label Switched (MPLS) Data Plane Failures", RFC 4379,
February 2006.
[RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson,
"Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for
Use over an MPLS PSN", RFC 4385, February 2006.
[RFC5586] Bocci, M., Vigoureux, M., and S. Bryant, "MPLS Generic
Associated Channel", RFC 5586, June 2009.
9.2. Informative References
[I-D.ietf-mpls-lsp-ping-enhanced-dsmap]
Bahadur, N., Kompella, K., and G. Swallow, "Mechanism for
performing LSP-Ping over MPLS tunnels",
draft-ietf-mpls-lsp-ping-enhanced-dsmap-08 (work in
progress), January 2011.
[I-D.ietf-mpls-p2mp-lsp-ping]
Yasukawa, S., Farrel, A., Ali, Z., Swallow, G., Nadeau,
T., and S. Saxena, "Detecting Data Plane Failures in
Point-to-Multipoint Multiprotocol Label Switching (MPLS) -
Extensions to LSP Ping", draft-ietf-mpls-p2mp-lsp-ping-15
(work in progress), January 2011.
[I-D.ietf-mpls-tp-identifiers]
Bocci, M., Swallow, G., and E. Gray, "MPLS-TP
Identifiers", draft-ietf-mpls-tp-identifiers-04 (work in
progress), March 2011.
[I-D.ietf-mpls-tp-oam-framework]
Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A.,
Bahadur, et al. Expires September 15, 2011 [Page 17]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
Hernandez-Valencia, E., Levrau, L., Sestito, V., Sprecher,
N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R.
Winter, "Operations, Administration and Maintenance
Framework for MPLS-based Transport Networks",
draft-ietf-mpls-tp-oam-framework-11 (work in progress),
February 2011.
[RFC1122] Braden, R., "Requirements for Internet Hosts -
Communication Layers", STD 3, RFC 1122, October 1989.
[RFC1812] Baker, F., "Requirements for IP Version 4 Routers",
RFC 1812, June 1995.
[RFC5003] Metz, C., Martini, L., Balus, F., and J. Sugimoto,
"Attachment Individual Identifier (AII) Types for
Aggregation", RFC 5003, September 2007.
[RFC5860] Vigoureux, M., Ward, D., and M. Betts, "Requirements for
Operations, Administration, and Maintenance (OAM) in MPLS
Transport Networks", RFC 5860, May 2010.
[RFC5884] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,
"Bidirectional Forwarding Detection (BFD) for MPLS Label
Switched Paths (LSPs)", RFC 5884, June 2010.
Authors' Addresses
Nitin Bahadur
Juniper Networks, Inc.
1194 N. Mathilda Avenue
Sunnyvale, CA 94089
US
Phone: +1 408 745 2000
Email: nitinb@juniper.net
URI: www.juniper.net
Bahadur, et al. Expires September 15, 2011 [Page 18]
Internet-Draft MPLS On-demand Connectivity Verification March 2011
Rahul Aggarwal
Juniper Networks, Inc.
1194 N. Mathilda Avenue
Sunnyvale, CA 94089
US
Phone: +1 408 745 2000
Email: rahul@juniper.net
URI: www.juniper.net
Sami Boutros
Cisco Systems, Inc.
3750 Cisco Way
San Jose, CA 95134
US
Phone:
Fax:
Email: sboutros@cisco.com
URI:
Eric Gray
Ericsson
900 Chelmsford Street
Lowell, MA 01851
US
Phone: +1 978 275 7470
Fax:
Email: eric.gray@ericsson.com
URI:
Bahadur, et al. Expires September 15, 2011 [Page 19]